THE DEFINING SERIES

Mud Logging
Matt Varhaug Standpipe

Senior Editor
Kelly Flowline
Gas trap
Since its commercial introduction in 1939, the mud logging unit has become Mud logging Rotary table
unit Shale
a hub for monitoring formation responses to the drilling process. Initially, Drill floor Suction line shaker
the mud loggers mandate was to record the depth and describe the lithol- Bell nipple
ogy of formations encountered by the drill bit then determine whether those Blowout
formations contained hydrocarbons. However, the scope of mud logging has preventer

expanded as additional sensors brought more data into the logging unit Mud Shaker
pump pit
such as gas chromatographs, weight-on-bit and mud pit level indicators.
Basic mud logging services now typically track drilling rates, lithology, Casing Suction Reserve
pit pit
visual hydrocarbon indicators, total combustible gas in mud and individual
hydrocarbon compounds in the gas along with numerous drilling parame-
ters. The mud logger monitors and evaluates a broad range of surface indi-
cators to compile a concise record of subsurface geology, hydrocarbons
Drillpipe
encountered and significant drilling events. These days, the term surface
logging is sometimes used to encompass a range of enhanced mud logging
services that incorporate advanced sensor and computing technology to
provide monitoring for wellbore stability and early kick detection .
Bit
The practice of mud logging relies heavily on the mud circulation system.
High-pressure mud pumps draw mud, or drilling fluid, from surface tanks and Figure 1. Monitoring the formation. Drilling mud, pumped downhole through
direct it downhole through the drillpipe (Figure 1). The mud exits the drill- the center of the drillpipe, enters the open borehole and carries away
string through nozzles in the bit. As a bit drills through the subsurface, the formation cuttings and fluids as it moves upward to the surface. There, the
rock it grindsalong with water, oil or gas in the formationis carried back mud, formation fluids and cuttings are diverted through a flowline to the
shale shaker. Gas is separated from the mud, and a suction line siphons the
up the hole by the drilling fluid. Upon reaching the surface, the fluid exits gas to the mud logging unit for analysis. Cuttings are sampled at the shaker
through a flowline above the blowout preventer and is deposited over a vibrat- screen and examined inside the unit. When these evaluations are combined
ing mesh screen at the shale shaker, which separates formation cuttings from with drilling parametersdrill rate, pump rate, pump pressure, weight on bit,
mud properties and other inputsthe mud logger can identify potential pay
the liquid mud. The liquid portion of the drilling fluid falls through the screens
zones and ascertain how the formation is reacting to the drilling process.
to the mud pits, ready to be pumped back into the well; the rock cuttings on
the shaker screen provide the basis for determining downhole lithology.
porosity, texture and other characteristics relevant to rock type. This infor-
Depth of Samples mation is plotted in the lithology column of the mud log, which displays an
The type of material flowing over the shaker and the timing of its arrival are estimate of gross lithology as a percentage of cuttings, reported in 10%
fundamental to the mud logging process. To characterize the lithology and increments. Because the presence of hydrocarbons may not be obvious
fluid content of a particular interval, the mud logger must account for the even under a microscopeeach sample is examined for fluorescence under
transport velocity of the cuttings to determine the time it takes cuttings to ultraviolet (UV) light.
travel from the bit to the shaker. This lag time increases as depth increases, Fluorescence can be an extremely sensitive indicator of the presence of
taking just a few minutes while the upper section of a well is drilled but hydrocarbons in drill cuttings. Sample fluorescence is evaluated in terms of
extending to several hours in deeper sections. Lag time, a function of depth color (ranging from brown to green, gold, blue, yellow or white), intensity
and mud pump rate, is usually measured in terms of pump strokes, which and distribution. Fluorescence color may indicate oil gravity; dark colors
are counted by a pump stroke counter at the mud loggers console. are suggestive of low API gravity heavy oils, and light colors indicate high
The lag time dictates when formation cuttings from a given depth will API gravity light oils. Following application of a solvent on the samples,
arrive at the shaker. Lagged cuttings samples are collected at regular depth hydrocarbon fluorescence will appear to flow and diffuse into the solvent as
intervalstypically every 3 m [10 ft] or 10 m [30 ft] of drillingand prior the oil dissolves. This diffusion is known as cut fluorescence, or more com-
to tripping out of the hole. Lagged samples are also collected to examine monly just cut. Under UV light, hydrocarbons may be seen to stream from
changes in formation characteristics, as indicated by significant changes in the rock pores into the surrounding solvent, turning the solvent cloudy.
drill rate or gas curve trends. To measure gas, the mud logger relies on an automated gas detection sys-
tem. Suction lines transport a constant stream of air and gas from the gas
Sample Analysis trap, located at the shale shaker, to the logging unit. There, sensitive instru-
Inside the logging unit, the mud logger rinses and dries cuttings samples ments process the gas samples extracted from the drilling mud. The primary
before examining them under a binocular microscope. The mud logger gas measurement tool is a flame ionization detector (FID), which can sense
describes each sample in terms of lithology, color, grain size, shape, sorting, hydrocarbon gas concentrations as low as 5 parts per million. From FID mea-
surements, a total gas curve can be plotted on the mud log. Background
Oilfield Review 2015. gasa more or less constant, minimum level of gasestablishes a baseline
Copyright 2015 Schlumberger.
www.slb.com/defining

on the total gas plot. A gas show is any Clay Shale Sandstone Sand Limestone Dolomite Anhydrite Coal
significant increase in detected gas,
FG Formation gas CG Connection gas TG Trip gas Oil and gas Oil Gas Bit change, trip Shoe
which is usually associated with a zone of
Chromatograph, ppm
increased porosity or permeability. ROP
C1 C2 C3
ft/h Depth, Cuttings, Total Gas, units Mud Weight,

Fluorescence
Lithological Description
For more detailed hydrocarbon analy- 100 50 0 ft % 0 125 250 375 500
iC4 nC4 ppg
and Notes
iC5 nC5
sis during shows, the mud logger employs 0.5k 1k 1.5k 2k 2.5k

1,000k
100k
a gas chromatograph. The chromatograph

100

10k
10

1k
7,500 Sandstone: Clr-lt gy-frst, m-f gr,
separates the gas stream into fractions sbelg-elg, sbang-sbrnd, m srt, tr Glau,
calc mtx, p-m cmt, qtzc i/p, m ind,
according to molecular weight. Commonly fri-m hd, p-fr intgran por, no fluor.
9 7/8-in. casing set at 7,580 ft MD/
detected components fall within the 6,691 ft TVD. LOT = 14.8 ppg.
In: 10.8
alkane group: methane [CH4]denoted 7,600 Out: 10.8
Clay: Lt brn-tan, arg, calc, plas,
sft, sol, slty, rthy, grty.
as C1as well as the following constitu- Shale: Lt gy-lt brn, grnsh gy, arg, calc,
frm-hd, occ sft, p-m cpt, sbblky-blky,
ents: ethane [C2H6] or C2, propane [C3H8] Trip for new bit Increase splty-ppy i/p, rthy, grty.
TG: 1,548 U
MW to 11.3
or C3, the normal and isopolymers of 6.3 bbl gain
Sandstone: Clr-lt gy-frst, m-f gr,
butane [C4H10] or nC4 and iC4 and pentane sbelg-elg, sbang-sbrnd, m srt, tr Glau,
calc mtx, p-m cmt, qtzc i/p, m ind,
7,700 CG: 35 U Increase
[C5H12] or nC5 and iC5. The measurement MW to 11.5 fri-m hd, p-fr intgran por, no fluor.

of these light hydrocarbons helps geolo- CG: 39 U Increase Shale: Lt gy-lt brn, grnsh gy, arg, calc,
MW to 11.7 frm-hd, occ sft, p-m cpt, sbblky-blky,
gists characterize reservoir fluid composi- CG: 45 U splty-ppy i/p, rthy, grty.

tion while drilling. The quantity of gas Clay: Lt brn-tan, arg, calc, plas,
7,800 sft, sol, stky i/p, rthy, grty.
recovered and the ratios of the various
Sand: Clr-frst, trnsp-trnsl, m-c gr,
gases are useful in identifying zones of WOB 38 to 53 klb occ f, sbelg-sbsph, ang-sbang, m srt,
RPM 78 to 84 tr Glauc, uncons-p cmt, p ind, lse, n por,
producible oil or gas. Flow 650 gpm Qtz, no fluor.

FG: 427 U
Clay: Lt brn-tan, arg, calc, plas,
7,900 sft, sol, stky i/p, rthy, grty.
Coordination with the Drill Floor Increase
Sand: Clr-frst, trnsp-trnsl, m-c gr,
Gas monitoring is also important to the FG: 920 U
MW to 12.0 occ f, sbelg-sbsph, ang-sbang, m srt,
tr Glauc, uncons-p cmt, p ind, lse,
driller and company representative. Qtz, no fluor.

Mud gas trends that develop while drill-

8,000
ing are integral to the evaluation of mud
balance and identification of potentially Figure 2. Excerpt from a basic mud log. A mud log typically displays ROP, depth, cuttings lithology, gas measurements
overpressured formations. By carefully and cuttings descriptions along with notes on mud rheology or drilling parameters. This log documents fairly routine
tracking gas and drilling parameters, drilling. Casing was set in a shaly interval at 7,580ft. After drilling out of casing, the driller ran a leakoff test (LOT).
Drilling ROP was about 25 to 30ft/h [7.6 to 9 m/h]. A trip for a new bit at 7,650ft resulted in 1,548units of trip gas (TG).
the mud logger can recognize deviations During drilling at near-balanced conditions, small increases in connection gas (CG) were observed following
from normal trends and give advanced each connection, prompting the driller to raise the mud weight. An increase in ROP at 7,890ft signified a drilling
warning so the driller can mitigate break, which was accompanied by increasing sand content and a gas show, which reached a peak of 920units of
impending problems. Thus, the success formation gas (FG).
of a well and the safety of the drilling
operation may hinge on how quickly a mud logger can synthesize and inter- logs from offset wells and help the operator track the bits position in relation
pret myriad pieces of data. to target formations. Because the mud log is based on physical samples, it can
A sensor mounted on the drawworks tracks the drill rate, or rate of pen- provide a direct, positive identification of lithology and indication of hydrocar-
etration (ROP), to determine the amount of time spent drilling each meter bon content. This information can be especially useful when formation char-
or foot of depth. The mud loggers role takes on added importance when a acteristics make wireline or LWD log interpretation complicated or ambiguous.
drilling break, or significant increase in ROP, is encountered. Then the mud The mud log provides independent evidence for a more comprehensive under-
logger alerts the company representative to request that drilling be stopped standing of reservoir conditions andgeology.
until mud and cuttings from the bit face can be circulated to the surface. If Advances in computing and networking systems, surface sensor design
these cuttings are accompanied by an increase in gas, or if sample analysis and sample analysis are bringing mud logging technology into the 21stcen-
reveals the presence of oil, the mud logger notifies the company representa- tury. Today, even more sensors lead into the logging unit, each acquiring
tive and geologist of a show of gas or oil. The operator then has the option to data at a frequency of several times per second. To handle this increase in
further evaluate the potential pay zone through coring or testing. data rate and volume, a context-aware processing systembased on com-
The mud log serves a variety of functions (Figure 2). The ROP curve is puter-generated trend lines and a library of established modelsmakes the
plotted as a step chart or a continuous line, increasing from right to left. When data easier for the mud logger and other end users to evaluate. Digital
displayed in this manner, the ROP curve responds to changes in rock type or images of samples viewed under the microscope can be rapidly transmitted
porosity in a manner similar to that of a spontaneous potential or gamma ray from the wellsite to the client office. New approaches to gas sampling and
curve, making for easy correlation between LWD or wireline curves. As a cor- analysis have been developed to extract geochemical properties at the well-
relation tool, the mud logs ROP and total gas curves often exhibit a remark- site. The mud logging unit has long been a hub for monitoring drilling opera-
able correspondence to gamma ray and resistivity curves, respectively. tions; its role as a source of crucial information for the company
Throughout the drilling process, mud logs provide real-time correlations with representative, the driller and the geologist continues to evolve.

Oilfield Review