MASTER CYLINDER #916-31926

#916-31933
#916-31935
#916-31939
#916-31948
Step-by-Step Installation Instructions

CAUTION: DO NOT allow brake fluid to contact

REMOVING THE ORIGINAL painted surfaces as the fluid damages paint. If contact
MASTER CYLINDER occurs, immediately flood the affected area with water.

6. Remove the nuts/bolts securing the master cylinder

NOTE: Before beginning work, be sure vehicle is to the firewall or power brake booster. DO NOT
parked in a level area and that wheels are chocked to remove power brake booster.
prevent unintentional movement. The master cylinder
MUST be level during the procedure.

1. Disconnect the ground cable from the battery.

2. On manual brake master cylinders (except some

Chrysler products), disconnect the push rod from the
brake pedal linkage under the dash. The rod eyelet is
attached to the pedal with a thru-bolt and cotter pin,
nut or retaining clip.

NOTE: Some Chrysler vehicles use manual brake

master cylinders with a "pop out" pushrod. After
removing the flange bolts, support the master cylinder
and use a wedge between the flange and firewall to
"pop" the pushrod from the piston. DO NOT separate the
pushrod from the brake pedal linkage (see illustration).

3. Disconnect electrical lead(s) from master cylinder's 7. Remove the master cylinder from the vehicle.
brake failure warning switch, if so equipped. CAREFULLY remove and save any fittings, rubber
hoses, clamps, plastic pipes, gaskets or other
components (including brake warning switches and
proportioning valves) for installation on the
replacement unit if necessary.

NOTE: If the replacement master cylinder is supplied

without a reservoir, you must remove and transfer the
reservoir from the original master cylinder to the
replacement unit. Refer to the following instructions.

TRANSFERRING THE RESERVOIR

1. Carefully drain remaining brake fluid from the
master cylinder.
4. Clean the area around the brake line connections on
the master cylinder. 2. Position the original master cylinder in a vise so the
jaws clamp onto the mounting flange. DO NOT
5. Disconnect brake lines from the master cylinder and TIGHTEN THE VISE JAWS ON THE MASTER
proportioning valve, if so equipped. Cover or plug CYLINDER BODY! This will cause damage and void
lines to prevent dirt from entering and contaminating the unit's core value.
the brake system.
Speedway Motors, Inc. 2006
 3. Use a pry bar or large screwdriver to "pop" the 1. Position the replacement master cylinder in a vise
reservoir off of the master cylinder (see illustration). so that the jaws clamp onto the mounting flange. DO
NOT TIGHTEN THE VISE JAWS ON THE MASTER
4. Remove the reservoir mounting grommets and
CYLINDER BODY! This will cause damage and void
install them on the replacement unit.
the warranty.
5. Lubricate the grommets and reservoir necks with
2. Install brake failure warning switch and
clean brake fluid. Carefully press the replacement
proportioning valve, if so equipped, onto the
master cylinder body down onto the reservoir using a
replacement master cylinder BEFORE bench bleeding
slight rocking motion.
the unit. Use the new O-rings supplied with the
6. Remove original master cylinder from vise. replacement unit on the valves and switch. Install
Put it into replacement carton to assure proper core plugs in the proportioning valve ports, if so equipped,
credit upon return. before bench bleeding.
3. Install bleeder tubes, if available, into the brake line
outlet ports or use plugs to seal the ports.
4. Add enough clean brake fluid to the reservoir so
that the bleeder tube ends are submerged beneath the
fluid level.
5. Use a wooden dowel or similar tool to slowly push
the master cylinder piston in about one inch, then
release the piston slowly.

CAUTION: Be careful to avoid spraying brake fluid!

Keep your face away from the open reservoir.

NOTE: Cores holding fluid, especially hydraulic units, 6. Wait 15 seconds and repeat step 5 until you no
MUST be drained before they are returned for core longer see air bubbles in the reservoir.
credit.
7. Replace the reservoir cover. Do not remove bleeder
tubes from the brake line fittings yet.
NOTE: Some fluid around the mouth of the piston bore
is normal and does not indicate leakage. This is a rust
inhibitive bore lubricant used during assembly.

BENCH BLEEDING THE MASTER CYLINDER

NOTE: "Bench bleeding" (removing air from the master
cylinder) must be completed BEFORE the replacement
unit is installed in the vehicle. Otherwise, the brake
pedal will be insufficient and THE WARRANTY WILL
BE VOID!
Speedway Motors, Inc. 2006

2
 NOTE: The master cylinder flange should fully seat on
INSTALLING THE REPLACEMENT
MASTER CYLINDER the power booster face without applying pressure to the
IMPORTANT: Your replacement master cylinder is master cylinder piston. If it does not seat properly, the
guaranteed to fit and function in its listed applications, push rod must be adjusted or replaced (see "Adjusting
even though it may be different in appearance from the the Push Rod" section that follows).
original unit (see illustration). 5. Loosely attach master cylinder to firewall or power
1. Install any remaining fittings, rubber hoses, clamps, booster with mounting bolts/nuts.
plastic pipes, or other components removed from the 6. Working under the dash, attach the push rod to the
original unit onto the replacement master cylinder. brake pedal linkage (manual brake master cylinders
2. If the replacement unit is supplied without a other than Chrysler).
pushrod, the original push rod must be used. 7. Remove temporary plugs from the brake lines.
Also, remove bleeder tubes or plugs one at a time from
NOTE: For Chrysler "pop out" style push rods, remove outlet fittings or proportioning valves and connect
the original rubber lock piece and replace with new one brake lines to the master cylinder.
NOTE: Use the brass adapters supplied with the
replacement unit if brake line fittings differ in size from
master cylinder ports.
8. Tighten master cylinder mounting nuts or bolts to
the manufacturer's specification.

supplied with replacement kit. Lubricate with fresh

brake fluid and "pop" back into new master cylinder
piston (see illustration on page 1).
3. Install sealing ring, gasket or space, if necessary, 9. Fill the reservoir to the correct level with fresh
between master cylinder and booster or firewall. brake fluid. NEVER reuse brake fluid that has been
THESE PARTS ARE CRITICAL TO THE drained from the system! Replace reservoir cover.
OPERATION OF THE REPLACEMENT CYLINDER!
NOTE: On GM applications using angle-mounted 10. Bleed master cylinder by using bleeding screws, if
master cylinders, the rear of the vehicle must be elevated so equipped, or the brake line fittings. Crack them
to bring the master cylinder to a level position. This loose one line at a time while an assistant applies
prevents air from being trapped. When raising the medium pressure to the brake pedal. Tighten the
vehicle,use a lift or jack stands. The use of a jack only is fittings before releasing the pedal or air will be sucked
very dangerous! into the system. DO NOT attempt to bleed air from
hydraulic system by using the piston stop screw on the
4. Position the replacement master cylinder on the side or bottom of the master cylinder.
firewall or over the booster mounting studs.
Speedway Motors, Inc. 2006

3
 11. Pedal should be high and firm after the
bleeding procedure. If it isn't, bleed the entire
hydraulic system using the bleeder screws at the
calipers or wheel cylinders. Follow the manu-
facturer's recommended wheel order and
procedure.
NOTE: Check master cylinder fluid level after
bleeding each wheel cylinder. DO NOT allow the
master cylinder to run out of fluid!
12. After completing the bleeding procedure, top
off the reservoir, if necessary, and replace master
cylinder cover.
13. Re-connect brake failure warning switch lead
to master cylinder, if so equipped.
14. Re-connect the battery ground cable.
15. Be sure the brake system is working properly
before moving the vehicle.

CAUSE AND POSSIBLE SOLUTION

MASTER CYLINDER COMPENSATING

BINDING/DAMAGED PEDAL LINKAGE

ADJUSTING THE MASTER

PUSH ROD OUT OF ADJUSTMENT

CYLINDER PUSH ROD

CONTAMINATED BRAKE FLUID

NOTE: Correct push rod length is essential to

INSUFFICIENT BRAKE FLUID

TROUBLESHOOTING
reliable braking. If the push rod is too long, it causes CHART
the master cylinder compensating ports to be
blocked off, eventually resulting in brake drag. If the

PORTS BLOCKED
rod is too short, excessive brake pedal travel and,

AIR IN SYSTEM
possibly, a groaning noise from the power booster
will be noticed. Check the adjustment of the push
rod using the following procedure. PROBLEM
1. Remove the master cylinder reservoir cover. BRAKES WON'T APPLY X X
2. Have an assistant depress the brake pedal EXCESSIVE PEDAL TRAVEL/EFFORT X X X
slightly. Watch for fluid movement when the brake SPONGY PEDAL X X X
pedal is depressed 3/8" to 1/2". This indicates
BRAKES DRAG OR WON'T RELEASE X X X
correct push rod length. On dual system master
cylinders, fluid movement may occur in the front BRAKES GRAB X X X
reservoir only.
3. If the pedal travels more than 1/2" before fluid BRAKE INSTALLATION ALERT: The selection and
movement is noticed, the push rod is too short. If installation of brake components should only be done by
nothing happens no matter how far the pedal is personnel experienced in the proper installation and operation
depressed, the push rod is too long. of braking systems. The installer must use his/her own
4. To adjust the push rod's length, remove the discretion to determine the suitability of the brake components
master cylinder from the vehicle. Turn the and brake kits for every particular application.
adjusting nut in to shorten the rod or out to Speedway Motors, Inc. makes no warranties, either expressed
lengthen the push rod (see illustration). or implied, including any warranty of merchantability or fitness
5. If the push rod is non-adjustable, use shims for a particular purpose, other than those contained in its
between the master cylinder and the firewall or current catalog or website with respect to the goods identified
power booster to shorten it. If too short, remove on the face of the invoice. There is no warranty expressed or
the push rod from the master cylinder or power implied as to whether the goods sold herby will protect the
booster and replace it with one of proper length. purchaser or ultimate user of such goods from injury or death.
Speedway Motors, Inc. 2006
6. Install the master cylinder and recheck push rod
length.
4
 IMPORTANT
DISCLAIMER In an effort to offer our customers the low prices, quick service and great value, Speedway Motors
reserves the right to change suppliers, specifications, colors, prices, materials. Each of the previous items is subject
to change without notice. Speedway is not responsible for any typographical errors or misinterpretations. Quantities
are limited on some items.

WARRANTY DISCLAIMER The purchaser understands and recognizes that racing parts, specialized street rod
equipment, and all parts and services sold by Speedway Motors, Inc. are exposed to many and varied conditions due
to the manner in which they are installed and used. Speedway Motors, Inc. makes no warranties, either express or
implied, including any warranty of merchantability or fitness for a particular purpose other than those contained in its
current catalog with respect to the goods identified on the face of the invoice. There is no warranty expressed or
implied as to whether the goods sold hereby will protect purchaser or ultimate user of such goods from injury or
death. Speedway Motors assumes no liability after this period.

DAMAGE CLAIMS Always inspect your package upon delivery. Inspect all packages in the presence of the delivery
driver. The driver must note any damage. Ask the driver the Carriers procedures for handling damage claims. You
must hold the original box, packing material and damaged merchandise for inspection or the carrier will not honor
the claim. Notify Speedway Motors customer service department for instructions on returning damaged goods.
Speedway is not responsible if no notification is given within 5 days of receipt.

SHORTAGES Always check the contents of your delivery to insure all the parts that you ordered were received. Please
read the invoice. Double check all packing materials, small items may be wrapped inside with these products.
Shortages may occur from damage to the box, so save all packing materials. Inspect the box for holes that would
allow parts to fall out. If you are missing any item(s) be sure to check your invoice for back orders or canceled items
before calling the customer service department. If Speedway has to split a shipment into multiple boxes, packages
may be delivered on different days. You need to contact the customer service department within 5 days of delivery
to assure the prompt replacement. Speedway Motors assumes no liability after this period.

REFUSALS All refused COD customers will be billed a 15% restocking charge plus freight to and from the
destination! If you have questions please contact Speedways customer service department.

WARRANTY CLAIMS If an item has a manufacturers warranty as being free from defects we will exchange only. If
the item has been used and you are requesting warranty work, this may take up to 30 days as warranty work is done
by the manufacturer NOT Speedway Motors. If you have any questions please contact customer service.

RETURNS Speedway wants you to be satisfied with your purchase. If within 30 days after you receive your shipment
you are not satisfied, you may return the item for refund or exchange. All exchanged or returned merchandise must
be in original factory condition with no modifications or alterations. Returned merchandise must include all packaging
materials, warranty cards, manuals, and accessories. If the items being returned need to be repackaged there will be
a re-packing charge. Re-pack the item in a sturdy box and include a copy of your invoice and complete the form on
the back of the invoice. You must ship orders back PRE-PAID. WE DO NOT ACCEPT COD SHIPMENTS. All exchanges
need to have reshipping charges included. Items that are returned after 30 days are subject to 15% restocking
charges. All fiberglass returned will have 15% restocking charge. No returns on electrical parts, video tapes, and
books. Absolutely no returns on special order or close out merchandise.

FREE CATALOGS Speedway Motors offers FREE catalogs for Race, Street, Sprint and Midget, Sport Compact and
Pedal Car restoration.
**Some items are not legal for sale or use in California on pollution controlled motor vehicles. These items are
legal in California for racing vehicles only which may never be used upon a highway.

Speedway Motors Inc., P.O. Box 81906

Lincoln, NE 68501 (402) 323-3200
www.speedwaymotors.com
Speedway Motors, Inc. 2007