Att Trans Tools

Since 1978 ATEC Trans-Tool has maintained a reputation for manufacturing and suppling the most complete line
of specialty tools and equipment for the transmission industry.

Reproduction of this material in whole or in part is strictly prohibited without prior written consent by ATEC Trans-Tool, LP, including all part numbers, drawings, pictures, logos, or descriptions. Reproduction of any or any part of these items is civilly and/or criminally punishable by law.
TRANSMISSION GENERAL TOOLS & EQUIPMENT

TRANSMISSION SERVICE a. Case Sleeving ....................................30 b. Bushing Driver Kits & Accessories ......................................31-32 c. Transmission-Support & Holding ..............................................33 d. Air Test Plates....................................34 e. Clutch Spring Compressors ....................................35
TRANSMISSION GEN. TOOLS-EQUIP
Specifications and descriptions on products in this catalog may change without notice.
f. Specialty Tools & Equipment ..........................................36-38
Copyright 2007 ATEC Trans-Tool All intellectual property and copyrights reserved.
FEATURED PRODUCTS
T-0015
UNIVERSAL LIP SEAL INSTALLER See Page 37 METAL VALVE BODY SMALL PARTS TRAY
T-0170- M
T-0171
TRANSMISSION FOOT PRESS
See Page 36
See Page 35
See Page 31
T-0220-39
T-0158-HD
CLUTCH DRUM SPRING COMPRESSOR See Page 42
T-0156-A
FULL LINE TRANSMISSION SUPPORT-HOLDING FIXTURES See Page 33
MASTER BUSHING DRIVER KIT
Contact Your Local Distributor or Mobile Tool Truck Dealer
PH: 1-800-531-5978 24 Hr. FAX 210-225-2114 www.atec-trans-tool.com
29
TRANSMISSION TOOLS & EQUIPMENT

TRANSMISSION SERVICE
Case Sleeving Tool Kits

Our case sleeving tools allow rebuilders to bore out worn areas of a transmission case, such as the governor bore, and install a sleeve in this area. With more cases becoming hardto-find and prices increasing, these tool kits will reduce rebuilding costs by quickly and easily refurbishing a case to be rebuilt.
T-1695 T-0 T-1695-SL

Governor Bore Case Sleeving Tool Kit For FIOD-AOD (RWD) w/ Overdrive) T-1690-SL-E AODE Bushing Replacement For T-1695 AOD only AODE only
T-0107
Governor Bore Repair Tool GM 350, 400
T-0
T-1690-SL-E
Bushing Replacement
T-2195
Governor Bore Case Sleeving Tool Kit For Toyota, Isuzu, Volvo (RWD)
T-0107-D
Governor Bore Bushing Driver
T-2195-SL
Bushing Replacement For T-2195
T-2494
Oil Pump Needle Bearing & Seal Tool For Ford AXOD
30104-A
Governor Bore Bushing For GM 350, 400 For T-0107 & T-0107-D
T-2494-SL
T-0495
Governor Bore Case Sleeving Tool Kit For Ford C3, A4LD (RWD)
T-2495
Valve Body Cover Pump Driveshaft Bore Repair Tool
T-0495-SL
T-2495-SL Bushing Replacement For T-2495 T-0 T-2795

Output Shaft Rear Washer Case Resurfacing Tool Kit For Ford C6
T-1116
Rear Case Bushing Sleeving Tool Kit For Ford C6 (66-80) Use T-2795-A adaptor for E4OD (RWD)
T-2795-SL
T-1116-SL-A
Bushing Replacement For T-1116 (rear w/o oil grooves)
T-2795-A
E4OD (RWD) Adaptor For T-1093, T-2795 Cuts case surface where the output shafts rear washer is seated, creating the ability to install an oversized heavy duty bronze washer which will save the worn case.
T-1116-SL-B
Bushing Replacement For T-1116 (front w/ oil grooves)
T-1195 T-1195-SL
Governor Bore Case Sleeving Tool Kit For GM 180/180C/Postal Vehicles Bushing Replacement For T-1195
T-2995
Rear Bushing Case Boring Tool For 4L80E
T-2995-SL
30
Contact Your Local Distributor or Tool Truck Dealer

BUSHING DRIVER KIT
19 Piece Solid Steel Kit
T-0220-19
Bushing Driver Kits BUSHING DRIVER KIT T-0220-20

20 Piece Solid Steel Kit
To be used to update the T-0220-20 bushing driver kit to make a complete 39 piece kit
Drives most popular domestic bushings. Can be expanded in the future with T-0220-19
MASTER BUSHING DRIVER KIT- 39 PC T-0220-39

Most complete kit in the industry. Drives over 200 different bushing - foreign & domestic Comes complete with numbered application chart and board
GM
125/125C 180/180C 200/200-4R/200C 250/250-C 325/325-4L 350/350C 400, 440-T4 700-R4 Powerglide Super Turbine 300
FORD
A4LD, AOD ATX, C3, C 4/5, C6, FMX, Jatco
CHRYSLER
A404/413/470 727 904/999 All bushing drivers available individually For longer driver handle, order T-0220-DR06A
T-1093
UNIVERSAL DRIVER HANDLE
T-0220-30
BUSHING DRIVER KIT 30 Piece
T-0
For threaded bushing drivers
T-0220-DRO6A
LONG UNIV. BUSHING DRIVER HANDLE
T-0220-EX
EXTENSION DRIVER HANDLE For Multiple Step Bushing Driver Kits Only
T-0280-C
CHISEL BUSHING CUTTER SEAL REMOVER * Use curl cut method * Also use as tailpipe cutter
31

Bushing Driver Kits T-0220-AOD

BUSHING DRIVER KIT
T-0220- RI
BEARING RACE INSTALLER Patented * Adjustable for all races 1 9/16 to 2 7/16 I.D. * Impact resistant head for positive dead blow drive * Can use extension driver T-0220-TH
For Ford AOD
T-0220-TH T-0220-350
BUSHING DRIVER KIT Long Dead Blow Extension Driver (use with T-0220- RI)
For GM 250, 250C, 350, 350C

3 Piece Multiple Step Bushing Driver Kit
T-0220-USAFE
DRIVER KIT FOR STABILIZER BUSHING SEALS 10 Piece Kit Chrysler, GM, Ford, others
T-0220-440MM
BUSHING DRIVER KIT
T-0220-US-1
STABILIZER BUSHING & SEAL Chrysler 78 and up left side - standard
Fits metric bushing in GM 440T4
T-0220-US-2 T-0220-700R4
BUSHING DRIVER KIT STABILIZER BUSHING & SEAL Chrysler 78 and up left side - narrow
For
GM 700-R4
T-0220-US-3
STABILIZER BUSHING & SEAL Chrysler 78 and up right side - narrow
T-0220-US-4 T-0220-RM
UNIVERSAL BUSHING REMOVER KIT For use with T-0154-HD & T-0154-C STABILIZER BUSHING & SEAL GM 85 and up (440T4) either side
T-0220-US-5
STABILIZER BUSHING & SEAL GM 80 and up either side
Reproduction of this material in whole or in part is strictly prohibited without prior written consent by ATEC Trans-Tool, LP, including all part numbers, drawings, pictures, logos, or descriptions. eproduction of any or any part of these items is civilly and/or criminally punishable by law.
T-0220-US-6
STABILIZER BUSHING & SEAL Ford 85 and up either side
32

HOLDING FIXTURE
Transmission Support & Holding Fixtures TRANSMISSION T-0156-A GENERAL SERVICE

Includes Base * Bench mounts * Full 360 degree swing * 90 degree locking increments * Fits popular domestic & foreign transmissions
SUPPORT AND HOLDING FIXTURES ON PAGES 17 GM TRANSMISSION HOLDING FIXTURE
T-1200
Includes Base
T-0156-AF
Without Base (Same features as above)
For GM 125/125C GM 440-T4

* Bench mounts
T-1200-F
GM TRANSMISSION HOLDING FIXTURE
T-0156-B
Includes Base * Bench mounts * Full 360 degree swing * 90 degree locking increments * All steel construction * Allows work comfort at any angle * Allows easy access to work on valve body
GM TRANSMISSION HOLDING FIXTURE
T-2018-F
Without Base (For Base Order T-0156-KM )
For GM 4T40-E * Bench mounts
T-0156-BF
T-0156-BB
HOLDING FIXTURE BASE (Adapts To:) T-0156-AF T-0156-BF T-1200-F T-2409-F T-2800-F T-0156-B Bench Mounts
FORD TRANSMISSION HOLDING FIXTURE
T-2409-F
Without Base (For Base Order T-0156-BB)
For Ford Transaxles
T-0
T-0156-KM
UNIVERSAL HOLDING FIXTURE BASE For use with T-2018-F GM holding fixture Bench Mounts
Reproduction of this material in whole or in part is strictly prohibited without prior written consent by ATEC Trans-Tool, LP, including all part numbers, drawings, pictures, logos, or descriptions.Reproduction of any or any part of these items is civilly and/or criminally punishable by law.
FORD TRANSMISSION HOLDING FIXTURE
T-2800-F
Without Base (For Base Order T-0156-BB)
For Ford E40D
33

Air Test Plates

Air test plates allows testing a transmission for leaks and valve body performance without complete reassembly or filling the transmission with fluid. Our air test plates are machined for reliable testing
GENERAL MOTORS
Applications ..........................Page ..............Part Number
T-2017
125C (3T40) ..............41..............T-1237 180C (3L30) ..............42..............T-1047 200C ..........................45..............T-1087 200-4R ......................45..............T-1717 250, 350 ....................48..............T-1017 350C ..........................48..............T-1017-A 325-4L..........................................T-1117 400 (3L80) ................51..............T-1247 440-T4 (4T60) ..........52..............T-2017 (4T60-E) ..............52..............T-2017-A 700-R4 (4L60) ..........58..............T-1517 (4L60-E) ..............58..............T-1517-A (4L80-E) ....................61..............T-2917
FORD
T-1617
CHRYSLER
C-3 ............................64..............T-0417 A4LD / 5R55E / 4R44E 67..............T-2617 C-6 ............................69..............T-0427 AOD ..........................74..............T-1617 AODE / 4R70W ........74..............T-1617-A ATX ............................77..............T-1817 AXOD ........................82..............T-2417 AXOD-E ....................82..............T-2417-A E4OD / 4R100 ..........84..............T-2817 4EAT, G4AEL ............98..............T-2717
A-500, 904, 727 ........92..............T-1317 A-604 ........................93..............T-1442 404, 413, 470 ............91..............T-1427 A-606 ........................95..............T-3217
T-1442
MISCELLANEOUS
Toyota 130 ................100............T-2147 Hyundai........................................T-5217 Suzuki ..........................................T-5117
T-2147 34

T-0157
UNIVERSAL QUICK LOCK SPRING COMPRESSOR
Clutch Spring Compressors T-0158- SPA

SNAPRESS UPDATE KIT Updates early model Snapress * compressors to the T-0158-SP version
T-0157- K
COMPRESSION RING KIT
T-0158- ZF18
3-4 CLUTCH SPRING COMPRESSOR ADAPTER
T-0158
TRANSMISSION CLUTCH SPRING COMPRESSOR (available individually) Only tool you will need to remove clutch pistons from virtually all automatic transmissions, foreign and domestic * Adapters included for Ford ATX, AOD, AXOD * Use on clutch drums with center shafts. TRANSMISSION FOOT PRESS
For ZF-HP18
T-0171
For removal of snap rings in drum. For removal of snap rings in rear of case. Includes longer legs for late model transmissions.
[Order adapter T-1456 for use on Chrysler 604]
T-0158- J
JAWS For T-0158
INDIVIDUAL ADAPTERS
T-0171- A
Small loop
T-0158- HD
CLUTCH DRUM SPRING COMPRESSOR MOST ECONOMICAL * Long legs for deep drums * Mounts on work bench or vise
T-0171- B
Large loop
T-0171- C
Cone shape
T-0
T-0158- 4L
SPRING COMPRESSOR LEG SET For use with T-0158-HD and T-0171 only
T-0171- J
ADJUSTABLE SPRING COMPRESSOR ADAPTER Fits T-0171 * Compresses 3 areas for more positive action. * A simple twist for all adjustments * Heavy duty construction
T-0158- SP
SNAPRESS CLUTCH SPRING COMPRESSOR
35

Specialty Tools And Equipment T-0004

VALVE BODY LOCK PIN REMOVER
T-0033- A
HEAVY DUTY FRONT PUMP REMOVER * E-Z removal of Ford, GM and Chrysler front pumps. * Quick change boots adapt for GM & Chrysler * Slide hammer adaptable * Removes pump without it rocking
T-0004- RT
REPLACEMENT TIP
T-0007
UNIVERSAL SPEEDOMETER DRIVEN GEAR REMOVER
T-0153- HD
FRONT PUMP & SPEEDOMETER GEAR REMOVER
T-0015
UNIVERSAL LIP SEAL INSTALLER
T-0164
PLUG - A - SEAL
T-0030- A
H GAUGE UNIVERSAL FRONT PUMP CLEARANCE GAUGE Longer, more coverage
T-0170
SMALL PARTS TRAY
T-0033
UNIVERSAL PUMP REMOVER Quickly removes conventional type pumps without damage
GET ORGANIZED * Made of oil resistant plastic * 13.5 x 18 * 15 compartments
T-0170- A
VALVE BODY PARTS TRAY * Made of oil resistant plastic * 13.5 x 18 * 30 compartments keep valve body parts separated
36

Specialty Tools And Equipment T-1090- HD T-0170- M

METAL VALVE BODY SMALL PARTS TRAY * Heavy duty metal construction OIL COOLER LINE FLUSHER * Completely self contained * Closed filtering system reuses cleaning fluid * Positive displacement pump * Carbon bearings for heavy-duty operation * All bronze pump body * Replaceable filter cartridge * Heavy-duty motor * Includes: hoses, filter and fittings * Ready for operation * A must for late model and lock up units
T-0222
GM & CHRYSLER FRONT PUMP ALIGNMENT BAND The only tool needed for most GM & Chrysler transmissions
T-0222- A
FORD FRONT PUMP ALIGNMENT BAND
REPLACEMENT FILTER (For T-1090-HD...above)
001730 T-1091
PULSATING TRANSMISSION COOLER FLUSHER
T-1052
UNIVERSAL TORQUE CONVERTER LEAK TESTER * Fits domestic & foreign * Includes fittings and adapters * Detects even smallest leaks * Instruction Manual
T-0
Flushes cooler before installing rebuilt transmission. Air operated. Removable filter. Includes adapters and hoses. No solvents.
RPK-1052
REPLACEMENT PARTS KIT FOR T-1052
T-1081
CONVERTER HOUSING SEAL REMOVER Use with T-0154-HD T-0099
T-3425
COOLER LINE BANJO FITTINGS * Quick easy hook-up for flushing transmission cooler * Use w/ large flusher or aerosol cans For Ford 4R20E, 4EAT Chrysler diesel truck, Mazda, Nissan, Iinfinity, B.M.W., Mercedes
37

Specialty Tools And Equipment T-3020

DRAIN PLUG KIT * Installs with one simple drilled hole * Eliminates oil spills when changing fluid or rebuilding
T-3237
TRS ALIGNMENT TOOL Universal
T-1033
T-5033- K
REVERSE CLUTCH FEED OIL PIPE SEAL INSTALLER KIT (4 Pieces) AXOD, 125, 125C, 200, 200C, 200-4R Also sold separately.
30110
GM 350 ADAPTER PLATE * Replace the Chevrolet 350 & 400 transmission with the plentiful B.P.O.C. 350 & 400 * Replace the 4-speed stick with the super performance B.P.O.C.400
T-2433 T-1033-A T-1233
T-8010
TRANSMISSION TEMPERATURE GAUGE * 150 - 320 degrees * Includes mounting bracket, lamp and sending unit
T-3236
UNIVERSAL BEARING SPLITTER Heavy duty fixture for removing bearing and gears
- - WANTED NEW TOOLS - IF YOU HAVE SUGGESTIONS FOR TOOLS YOU WOULD LIKE TO SEE INCLUDED IN OUR LINE OF PRODUCTS PLEASE DROP US AN EMAIL OR LETTER WITH A COMPLETE DESCRIPTION OF THE PRODUCT AND, IF POSSIBLE, A PHOTO, ADVERTISEMENT OR FLYER.
NEW ITEM
T-9201
ONE FITS ALL GRINDING WHEEL
IMAGE NOT AVAILABLE
* Super abrasive cutting properties * Lasts up to ten times longer than regular wheels * Use of corner cutters eliminated
38
GENERAL MOTORS OLD TO NEW TRANSMISSION CONVERTIONS 125C ........................(3T40) 180C ........................(3L30) 180C-4 Spd Elec......(4L30-E) 400 ............................(3L80) 4 Spd Elec................(4L80-E) 440-T4 ......................(4T60) 440-T4 Elec ..............(4T60-E) 475 (HD400) ............(3L80-HD) 700-R4 ......................(4L60) 700-R4 Elec..............(4L60-E) MH1 ..........................(4T80-E) 4 Spd FWD ..............(4T40-E)
AUTOMATIC TRANSMISSION
SPECIFIC TOOLS FOR: GENERAL MOTORS
Transmission Type
a. b. c. d. e. f. g. h. i. j. k. l. m. 125, 125C (3T40) (3T40-E) ..................40-41 180, 180C (3L30) (4L30-E) ..................42-43 200, 200C, 200-4R ..............................44-45 250, 250-C, 350, 350C ........................46-48 325, 325-4L ..........................................49 375, 400 (3L80), 425, 475 (3L80-HD) 50-51 440-T4, F7, (4T60) (4T60-E) (4T65-E) 52-54 (4T40-E) ..............................................55 (4T80-E) ..............................................56 700-R4 (4L60) (4L60-E) ......................57-59 (4L80-E) ..............................................60-61 Powerglide. ........................................62 JF403-E (Nissan) ................................62
GM TRANSMISSION TOOLS-EQUIP
FEATURED PRODUCTS
T-1503
STATOR SHAFT TEFLON SEAL INSTALLER RESIZER See Page 58
T-0158-HD
T-2926
FOURTH CLUTCH PISTON & HOUSING LIP SEAL
See Page 61
INSTALLER PROTECTOR KIT
T-1574
TURBINE SHAFT TEFLON SEAL INSTALLERRESIZER
See Page 53 INPUT SHAFT TEFLON SEAL INSTALLATION KIT
T-2004
See Page 58 OIL PUMP REMOVER
T-1055
See Page 59
39
AUTOMATIC TRANSMISSION TOOLS

GENERAL MOTORS
125, 125C (3T40) (3T40E) T-0154- HD

SLIDE HAMMER SET HEAVY DUTY * With 3/8 threaded shaft tip
T-1200
HOLDING FIXTURE WITH BASE
(Also 440-T4, 4T60-E)
T-1200- F T-0154- E
1/2 SLIDE HAMMER ADAPTERS [Use with T-0154-HD] HOLDING FIXTURE WITHOUT BASE
T-1201
OUTPUT SHAFT C-RING REMOVER & INSTALLER
(Also 440-T4, 4T60-E)
T-1264
CONVERTER END PLAY CHECKER Also use as a side gear checking tool
(Also 200-4R, 4T60E, 4L60E, 3L80)
T-1202- A
CLUTCH ASSEMBLY AND FINAL DRIVE REMOVER-INSTALLER
T-1059- B
(Also 440-T4, 4T60-E)
METAL LO-REVERSE CLUTCH CENTER SUPPORT UNIT REMOVERINSTALLER

(Also 200, 200C,325, 325-4L)
T-1203
OUTPUT SHAFT LOADING AND ALIGNING TOOL
(Also 325, 325-4L, 440-T4, 4T60-E)
T-1059-HD
METAL LO-REVERSE CLUTCH CENTER SUPPORT UNIT REMOVERINSTALLER * Positive locking action. Works with or without bushing intact * Built-in slide hammer - to remove bound housings.
(Also 200, 200C,325, 325-4L)
T-1205
SEAL BEARING RACE INSTALLER [ Use with T-1093]
(Also 440-T4, 4T60-E)
T-0
T-1112
CUP PLUG INSTALLER
(Also 325, 325-4L)
40

GENERAL MOTORS
T-1206
PARK NEUTRAL SWITCH ALIGNER For (3T40E)
(Also 4T60E)
125, 125C (3T40) (3T40E) T-1237

AIR TEST PLATE
T-1207
AXLE SHAFT PULLER For (3T40E) Tripot drive joint 81- up [Use with T-0154-HD]
T-1238
AXLE SHAFT REMOVER [Use with T-0154-HD]
T-1208
AXLE SHAFT SEAL INSTALLER Installs axle seal w/o removal of output shaft (Use with T-1093)
(Also: 440-T4, 4T60, 4T60-E)
T-1239
BAND APPLY PIN GAUGE
T-1208-A
RIGHT & LEFT AXLE SEAL INSTALLER * Installs axle seal without removal of output shaft, while in or out of car.
(Also 440-T4)
T-1263
CONVERTER SEAL INSTALLER
T-1217
BOOT SEAL CLAMP INSTALLER
T-1274
TURBINE SHAFT SEAL INSTALLER - RESIZER 125 cover side only
(Also 440-T4)
T-0
T-1233
125/125C REVERSE CLUTCH FEED OIL PIPE SEAL INSTALLER
T-1274- A
TURBINE SHAFT SEAL INSTALLER-RESIZER 125C case side only
(Also 440-T4)
41

GENERAL MOTORS
180, 180C (3L30) (4L30-E) T-0030- A

H GAUGE UNIVERSAL FRONT PUMP CLEARANCE GAUGE Longer more coverage
T-1001
SHIFT LEVER SEAL REMOVER-INSTALLER Does not require draining fluid
T-0085
FRONT PUMP SEALER TOOL
T-1001- PV
SHIFT LEVER SEAL REMOVER-INSTALLER Does not require draining fluid
T-0131
EXTENSION HOUSING SEAL INSTALLER
Longer Version
T-0134
FRONT PUMP SEAL INSTALLER
T-1047
AIR TEST PLATE
T-0154- HD
HEAVY DUTY SLIDE HAMMER SET With 3/8 threaded shaft tip
T-1055
OIL PUMP REMOVER For (4L30-E)
T-0158- HD
CLUTCH DRUM SPRING COMPRESSOR (Other models on pg 49)
T-1068
FRONT END PLAY CHECKING ADAPTER For (4L30-E) [Use with T-1055]
T-0160
EXTENSION HOUSING BUSHING REMOVER AND INSTALLER
(Also 200, 200C, 200-4R)
T-1080
CONVERTER HOUSING TO FRONT PUMP ALIGNMENT Early 1969-1981 No 4L30E
T-0160- A
EXTENSION HOUSING BUSHIING REMOVERINSTALLER & OUTPUT SHAFT SUPPORT FIXTURE
T-1080- PV
SAME AS ABOVE FOR POSTAL VEHICLES
42

GENERAL MOTORS
T-1080-A
CONVERTER HOUSING TO FRONT PUMP ALIGNMENT TOOL Late 1982-Up Pontiac Only No postal vehicles 3L30E
180, 180C (3L30) (4L30-E) T-2012

CRANKSHAFT HUB HOLDING FIXTURE For 4L30-E To allow removal of the hold-down nut.
T-1080- B
PUMP ALIGNMENT TOOL 4L30E
T-2013
REAR HUB HOLDING TOOL For 4L30-E Also hold axle flange & transmission flange.
T-1081
CONVERTER HOUSING SEAL REMOVER [Use with T-0154-HD T-0099 ]
T-2014
EXTENSION HOUSING SEAL INSTALLER For 4L30-E Used to install to the proper depth.
T-1082
SECOND CLUTCH PISTON SEAL INSTALLER AND PROTECTOR
T-2039
OVERRUN CLUTCH SPRING COMPRESSOR ADAPTER
T-1085- A
THIRD CLUTCH SNAP RING COMPRESSOR Late 79 - up
T-2040
SERVO-3rd CLUTCH SPRING COMPRESSOR For 3L30, 4L30-E
T-1088
OIL PUMP SUN GEAR INSTALLER [Use with T-1093]
T-2041
ALIGNMENT PIN For 3L30, 4L30-E 2 required
(Also 250, 350)
T-1089
SERVO PISTON RING INSTALLER
T-2143
TURBINE SHAFT SIZING RING TOOL [For 4L30E]
T-1264
(Also 200-4R, 4T60E, 4L60E, 3L80)
CONVERTER END PLAY CHECKER Also use as a side gear checking tool
43

GENERAL MOTORS
200, 200C, 200-4R T-0030- A

H GAUGE UNIVERSAL FRONT PUMP CLEARANCE GAUGE
T-0166
LINE A PUMP KIT
T-0033
HEAVY DUTY FRONT PUMP REMOVER
T-0222
FRONT PUMP ALIGNMENT BAND
T-1001 T-0126
ACCUMULATOR PISTON COMPRESSOR ADAPTER
(Also: 375, 400, (3L80) 475 (3L80-HD)
SHIFT LEVER SEAL REMOVER-INSTALLER
T-1033
REVERSE CLUTCH FEED OIL PIPE SEAL INSTALLER For 200, 200C
T-0127
ACCUMULATORSERVO PISTON REMOVER [Use with T-0126]
(Also: 325, 400 (3L80) (3L80-HD)
T-1033- A
REVERSE CLUTCH FEED OIL PIPE SEAL INSTALLER For 2004-R
T-0131
T-1055
OIL PUMP REMOVER & END PLAY TOOL [Use with T-1068 ]
(Also 700-R4)
T-0156- B
HOLDING FIXTURE WITH BASE
T-1056
DIRECT CLUTCH LIP SEAL INSTALLER AND PROTECTOR
(Also 325, 325-4L)
T-0156- BF
FIXTURE W/O BASE
T-0160
EXTENSION HOUSING BUSHING REMOVER AND INSTALLER Can be used while in car
(Also: 3L30)
T-1057
LO-REVERSE CLUTCH LIP SEAL INSTALLER AND PROTECTOR
(Also 325, 325-4L)
T-0160- A
EXTENSION HOUSING BUSHING REMOVERINSTALLER & OUTPUT SHAFT SUPPORT FIXTURE *Speeds up process
T-1264
CONVERTER END PLAY CHECKER
44

GENERAL MOTORS
T-1059- B
(Also 125, 125C, 325, 325-4L )
200, 200C, 200-4R T-1702

PRESSURE REGULATOR VALVE SNAP RING INSTALLER For 200-4R Only
(Also 700-R4, 4L60)
METAL LO-REVERSE CLUTCH CENTER SUPPORT UNIT REMOVER AND INSTALLER
T-0
T-1059- HD
(Also 125, 125C, 325, 325-4L)
T-1703
FRONT PUMP SPRING LOADER TOOL
HEAVY DUTY LO-REVERSE CLUTCH CENTER SUPPORT UNIT REMOVER AND INSTALLER
T-1705
FOURTH CLUTCH COMPRESSOR AND CENTER SUPPORT REMOVER TOOL For 200-4R Only
T-1060
OUTPUT SHAFT & REAR UNIT SUPPORT FIXTURE 200, 200C Only [For 200-4R must use T-1760]
T-1717
VALVE BODY AIR TEST PLATE For 200-4R Only
T-1060- P
REPLACEMENT PLUNGER FOR T-1060
T-1060- A
OUTPUT SHAFT & REAR UNIT SUPPORT FIXTURE *Doubles as holding fixture
T-1735 T-1727
OVERRUN CLUTCH INNER PISTON LIP SEAL INSTALLER PROTECTOR
T-1061
INTERMEDIATE BAND APPLY PIN GAUGE
(Also: 325, 325-4L)
For 200-4R Only
T-1735
SERVO COVER DEPRESSOR * For use with pan on * On or off car use (Also 700-R4 )
T-1063
PUMP SEAL INSTALLER
(Also: 700-R4, 4L60)
T-1739
FORWARD & DIRECT CLUTCH REMOVER & INSTALLER, END PLAY CHECKER AND SHAFT BUSHING REMOVER For 200-4R Only
T-1068
[Use with T-1055) END PLAY CHECKING FIXTURE ADAPTER 245MM TORQUE CONVERTER
T-1760
OUTPUT SHAFT SUPPORT FIXTURE For 200-4R Only [Use with T-1060]
T-1072
SNAP RING REMOVER AND INSTALLER
T-1774
TURBINE SHAFT SEAL INSTALLER-RESIZER For 200-4R Only
T-1087
AIR TEST PLATE 200C Only [For 200-R4 use T-1717]
45

GENERAL MOTORS
250, 250C, 350, 350C T-0030- A

H GAUGE UNIVERSAL FRONT PUMP CLEARANCE GAUGE Longer & more coverage
T-0131
T-0134 T-0033
HEAVY DUTY FRONT PUMP REMOVER FRONT PUMP SEAL INSTALLER
T-0135
LIP SEAL INSTALLER PROTECTOR KIT
T-0033- A
HEAVY DUTY FRONT PUMP REMOVER Forward Direct Available Individually
T-0085
Intermediate
T-0135- A T-0135- B T-0135- C T-0151

REAR CLUTCH SPRING COMPRESSOR
T-0107
GOVERNOR BORE REPAIR TOOL [Use with T-30104-A, T-0107-D]
T-0153- HD
FRONT PUMP & SPEEDOMETER GEAR REMOVER
T-0
T-0107- D
GOVERNOR BORE BUSHING DRIVER [Use with T-30104-A, T-0107]
T-0154- HD
T-0127
ACCUMULATOR SERVO PISTON REMOVER
46

GENERAL MOTORS
T-0156- B
TRANSMISSION HOLDING FIXTURE WITH BASE
250, 250C, 350, 350C T-0814- A

ACCUMULATOR PRY BAR
T-0156- BF
ABOVE W/O BASE
T-0814- C
ACCUMULATOR PRY BAR WITH BOLT
T-0160- A
EXTENSION HOUSING BUSHING REMOVER INSTALLER AND OUTPUT SHAFT SUPPORT FIXTURE
T-1001 T-0166
LINE A PUMP KIT * Works without draininig fluid SHIFT LVER SEAL REMOVER-INSTALLER
T-0220-20
BUSHING DRIVER KIT (20 Piece)
T-1006
GOVERNOR HOLDING FIXTURE
T-0220-350
T-0
3 PIECE MULTIPLE STEP BUSHING DRIVER KIT
For more information about ATEC products, log onto our website:
www.atec-trans-tool.com
T-0220- EX
EXTENSION DRIVER HANDLE For multiple step bushing driver kits only
47

GENERAL MOTORS
250, 250C, 350, 350C T-1017

AIR TEST PLATE [For 250, 350C]
T-1072
T-1017- A
FOR 350C ONLY
T-1097
FRONT PUMP ALIGNMENT TOOL
T-1039- A
STATOR BUSHING REMOVER-INSTALLER
T-1264
T-1043- A
BUSHING REMOVER AND INSTALLER
T-2041
ALIGNMENT PIN
T-1055
OIL PUMP REMOVER
2 required
(Also: 3L30, 4L30E)
T-0
[When used with T-1068]
30104-A
GOVERNOR BORE BUSHING [Use with T-0107,T-0107-D]
T-1068
END PLAY CHECKING FIXTURE ADAPTER 245MM TORQUE CONVERTER [Use with T-1055]
30110
ADAPTER PLATE 350 * Replace 350 with the plentiful B.P.O.C. 350
T-1071- A
DIRECT CLUTCH ACCUMULATOR PISTON REMOVER AND INSTALLER
48

GENERAL MOTORS
T-0085
325, 325-4L T-1061

INTERMEDIATE BAND APPLY PIN GAUGE
T-0134
T-1072
T-1001
SHIFT LEVER SEAL REMOVER-INSTALLER * Removes & installs without draining fluid
T-1092
BEARING RACE INSTALLER
Also: 3L80, 375, 400, 3L80-HD, 475, 4L60, 4L60E, 700-R4, 325, 325-4L, JF403E-GEO
T-1056
DIRECT CLUTCH LIP SEAL INSTALLER & PROTECTOR
Also: 200, 200C, 200-4R
T-1112
CUP PLUG INSTALLER
T-1057
REVERSE CLUTCH LIP SEAL PROTECTOR
Also: 200, 200C, 200-4R
T-1174
TURBINE SHAFT TEFLON SEAL INSTALLER - RESIZER
T-1059-B
METAL LO-REVERSE CLUTCH CENTER SUPPORT UNIT REMOVER-INSTALLER
Also: 125,125C, 200, 200C, 200-4R
T-1203
OUTPUT SHAFT LOADING & ALIGNING TOOL
Also: 125, 125C, 440-T4
T-1217 T-1059-HD
* Positive locking action. Works with or without bushing intact * Built-in slide hammer - to remove bound housings BOOT SEAL CLAMP INSTALLER
METAL - HEAVY DUTY LO-REVERSE CLUTCH CENTER SUPPORT UNIT REMOVER & INSTALLER
T-1264
Also: 125, 125C, 200, 200C, 200-4R
49

GENERAL MOTORS
375, 400, (3L80), 425, 475 (3L80-HD) T-0030- A

H GAUGE UNIVERSAL FRONT PUMP CLEARANCE GAUGE * Longer, more coverage
T-0126
ACCUMULATOR PISTON COMPRESSOR ADAPTER For remover order T-0127
T-0033
UNIVERSAL PUMP REMOVER * Quickly removes conventinal type pumps without damage. [Use with T-0126]
T-0127
T-0128
REAR GEAR HOLDING FIXTURE ADAPTER [Use with T-0129]
T-0033- A
T-0129
HOLDING FIXTURE
T-0085
FRONT PUMP SEALER TOOL * Small shaft For 400 only
[Use with T-0128]
T-0131
T-0099
UNIVERSAL SEAL REMOVER
T-0133
EXTENSION SEAL INSTALLER
T-0
T-0107
GOVERNOR BORE REPAIR TOOL [Use with T-0107-D]
T-0134
T-0107- D
GOVERNOR BORE BUSHING DRIVER [Use with bushing 30104-A] For repair tool order T-0107
T-0153-HD
FRONT PUMP AND SPEEDOMETER GEAR REMOVER
T-0124
LIP SEAL INSTALLER PROTECTOR KIT T-0124-A Inner; T-0124-B Outer; T-0124-C Intermediate
T-0156- B
T-0125
REAR GEAR ASSEMBLY REMOVER AND INSTALLER [Use with T-0099]
T-0156- BF
HOLDING FIXTURE WITHOUT BASE
50

GENERAL MOTORS
375, 400, (3L80), 425, 475 (3L80-HD) T-1055 T-0158-HD

CLUTCH DRUM SPRING COMPRESSOR OIL PUMP REMOVER
T-1072 T-0160-A
EXTENSION HOUSING BUSHING REMOVER & INSTALLER SNAP RING REMOVER AND INSTALLER
T-1092
Also: 4L60, 4L60-E, 700R4, 325, 325-4L, JF403E-Geo
T-0161
EXTENSION HOUSING BUSHING REMOVER AND INSTALLER [GM]
T-1094
REAR PINION BEARING RACE INSTALLER Also used to install crankshaft gear
T-0163- A
HEAVY DUTY VACUUM PUMP
T-1097 T-0163- C
PRESSURE GAUGE * 0-100 Lbs. FRONT PUMP ALIGNMENT BAND For 375, 400 only.
Also: 350, 700-R4, Powerglide GM TRANSMISSION TOOLS-EQUIP
T-0163- D
PRESSURE GAUGE * 0-300 lbs
T-1247
AIR TEST PLATE For 400 (3L80)
T-0166
LINE A PUMP KIT
T-1264
CONVERTER END PLAY CHECKER Also used as a side gear checking tool.
Also: 200-4R, 3T40E, 4T60E, 4L60E
T-0220-20
BUSHING DRIVER KIT (20 Piece)
T-1502
SPEED SENSOR ROTOR INSTALLER KIT
T-1001
30104- A
GOVERNOR BORE BUSHING [Use with T-0107, T-0107-D]
T-1006
GOVERNOR HOLDING FIXTURE
51

GENERAL MOTORS
440-T4, F7 (4T60) (4T60-E) (4T65-E) T-1093

UNIVERSAL DRIVER HANDLE For threaded bushing drivers
T-1205
SEAL AND BEARING RACE INSTALLER Use with T-1093
Also:125, 125C,
T-1206 T-1200
HOLDING FIXTURE WITH BASE PARK-NEUTRAL SWITCH ALIGNER
Also: (3T40E)
T-1200-F
HOLDING FIXTURE WITHOUT BASE Use with T-0156-BB
Also 125, 125C
T-1208
AXLE SHAFT SEAL INSTALLER * Installs without removal of output shaft [Use with T-1093 driver handle]
T-1201
OUTPUT SHAFT C-RING REMOVER AND INSTALLER
T-1208- A
RIGHT & LEFT AXLE SEAL INSTALLER * Installs axle seal without removal of output shaft while in or out of car
Also 125, 125C
T-1202-A
CLUTCH ASSEMBLY AND FINAL DRIVE REMOVER-INSTALLER
T-1209
MODULATOR CHECKING TOOL * 87 to current
Also: 125, 125C
T-1217 T-1203
OUTPUT SHAFT LOADING AND ALIGNIING TOOL To remove final drive order T-1202-A
Also: 125,125C, 325, 325-4L
BOOT SEALER CLAMP INSTALLER
T-1264
CONVERTER END PLAY CHECKER Also use as side gear checking tool.
Also: 200-4, (3T40E) (4K60E) (3K80)
52

GENERAL MOTORS
440-T4, F7 (4T60) (4T60-E) (4T65-E) T-1263 T-2004- C

TORQUE CONVERTER SEAL INSTALLER INPUT SHAFT SEAL RESIZER
Also: 125, 125C
T-1274
TURBINE SHAFT TEFLON SEAL INSTALLER-RESIZER * 440-T4 cover side only
Also: 125, 125C
T-2005
OUTPUT SHAFT LOADING TOOL ADAPTER For (4T60-E) only [Use with T-1203]
T-1274- A
TURBINE SHAFT TEFLON SEAL INSTALLER-RESIZER * 440-T4 case side only
Also: 125, 125C
T-2006
THERMO ELEMENT HEIGHT GAUGE
T-2003
OUTPUT SHAFT LOADING TOOL ADAPTER [Use with T-1203]
T-2007
SPROCKET SUPPORT BEARING INSTALLER [Use with T-1215 bushing driver handle]
T-2004
INPUT SHAFT TEFLON SEAL INSTALLATION KIT Also 4T80E
NO PHOTO AVAILABLE
T-2008
AXLE SEAL INSTALLER [Left side]
T-0 T-0
All tools can be ordered individually- below
T-2004- A
INPUT SHAFT SEAL INSTALLER
T-2017
VALVE BODY AIR TEST PLATE For 440-T4 (4T60)
T-2017-A T-2004- B
INPUT SHAFT SEAL GUIDE VALVE BODY AIR TEST PLATE For (4T60-E)
53

GENERAL MOTORS
440-T4, F7 (4T60) (4T60-E) (4T65-E) T-2027

INPUT CLUTCH PISTON LIP SEAL INSTALLER PROTECTOR
T-2055
INPUT SHAFT END PLAY TOOL * Check correct input shaft end play tolerance * No dial indicator required
T-2028
THIRD CLUTCH PISTON LIP SEAL INSTALLER PROTECTOR
T-2056
2nd CLUTCH PISTON SEAL INSTALLER For (4T60-E) only
T-2029
AXLE REMOVAL WEDGE * Remove the retaining ring to the output shaft-carrier assembly
T-2059
CLUTCH ASSEMBLY FINAL DRIVE REMOVER-INSTALLER For (4T60-E)
T-2042
DRIVESHAFT BEARING REMOVER AND INSTALLER For (4T65-E) * Double ended tool
Also: (4L80-E)
T-2061
1-2 AND REVERSE BANDS APPLY PIN GAUGE * Necessary tool for gauging dimensions for selection of the proper length of apply pins
T-0 T-0
T-2043
SECOND CLUTCH PISTON SEAL INSTALLER For (4T65-E) * Allows installation in the clutch housing, protecting it from damage
T-2062
1-2 BAND STOP INSTALLER
54

GENERAL MOTORS
T-0154-HD
(4T40-E) T-2024
COAST CLUTCH SPRING COMPRESSOR Allows the retaining ring to be removed or installed.
T-1206
PARK NEUTRAL SWITCH ALIGNER
T-2026
COOLER PIPE SEAL REMOVER AND INSTALLER
T-2011
T-0
FORWARD CLUTCH INNER SEAL REMOVER [Use with 3 jaw puller]
T-2026-A
PIPE SEAL INSTALLER BOLT This tool is a longer forcing screw that can be used on both seal positions in the 4T40E case which has been modified in the cooler line attachment area.
T-2015
OUTPUT SHAFT SEAL REMOVER * Access the stub shaft axle sleeve where standard pullers cannot be used.
T-2030
INPUT SHAFT TEFLON SEAL INSTALLER KIT Installs seals on direct/coast clutch assembly.
T-2016
OUTPUT SHAFT SLEEVE INSTALLER * Install new sleeve onto the output (stub) shaft while maintaining a lateral runout of .001.
T-2018-F
HOLDING FIXTURE [Use with T-0156-KM]
TRANS CONNECTOR REMOVER * Remove the transaxle wiring harness connector from the trans case. AXLE SEAL INSTALLER
T-2035
T-2036
T-2019
FWD-REV CLUTCH INNER SEAL INSTALLER * Used to press the inner seal into the forward clutch housing.
* Includes a driver and protector for inner axle seal lip for installing right and left axle seals into the case.
T-2037
TORQUE CONVERTER SEAL REMOVER
T-2020
2nd CLUTCH SPRING COMPRESSOR
T-2021
REVERSE CLUTCH INNER SEAL INSTALLER * Driver used to install the seal assembly onto the reverse clutch.
MANUAL SHAFT PIN INSTALLER This tool is used as a driver to achieve the proper height.
T-2038
T-2058
OUTPUT SHAFT ASSEMBLY REMOVER AND INSTALLER Use with T-0154-HD and 4L60-E
T-2023
2nd ROLLER CLUTCH INSTALLER * Plastic driver used to install the retainer onto the reverse clutch housing.
55

GENERAL MOTORS
(4T80-E) T-1206
T-3305
COAST CLUTCH SEAL PROTECTOR * Inner seal
T-2004
INPUT SHAFT SEAL INSTALLER
(Also: 440-T4)
T-3306
TORQUE CONVERTER SEAL INSTALLER
T-3300
TRANSAXLE HOLDING FIXTURE {Use with T-0156-KM}
T-3307
CASE COVER TO SHAFT SEAL REMOVER-INSTALLER
T-3301
AXLE SHAFT SEAL INSTALLER SET
T-3308
SPROCKET SHAFT SEAL INSTALLER
T-3302
FORWARD COAST CLUTCH ASSEMBLY REMOVER AND INSTALLER
T-3309
VALVE BODY GUIDE PINS ( Set of 3)
T-3310
DRIVE SPROCKET SEAL INSTALLER [Use with T-1093]
T-0
T-3303
REVERSE CLUTCH SEAL PROTECTOR * Inner seal
T-3311
INPUT END PLAY LIFTING TOOL
T-3304
FORWARD CLUTCH SEAL PROTECTOR * Inner seal
56

GENERAL MOTORS
T-0030- A
700-R4 (4L60) (4L60-E) T-0160- A

EXTENSION HOUSING BUSHING REMOVER INSTALLER AND OUTPUT SHAFT SUPPORT FIXTURE * Eases & speeds removal and replacement of bushings.
T-0107
GOVERNOR BORE REPAIR TOOL [Use with T-0107-D]
T-0163- A
VACUUM PUMP HEAVY DUTY STYLE
T-0107- D
GOVERNOR BORE BUSHING DRIVER [Use with bushing #30104-A]
T-0163- C
PRESSURE GAUGE 0 -100 lbs
T-0127
T-0163- D
PRESSURE GAUGE 0 - 300 lbs
T-0220-700R4 T-0131
EXTENSION HOUSING SEAL INSTALLER BUSHING DRIVER KIT
T-1001 T-0149
INPUT CLUTCH HOUSING SPRING COMPRESSOR SHIFT LEVER SEAL REMOVER-INSTALLER
T-1001-PV
Same as above for postal vehicles
T-1264
T-0151
Also: 200-4R, 3T40E, 4T60E, 3L80
57

GENERAL MOTORS
700-R4 (4L60) (4L60-E) T-1055

OIL PUMP REMOVER AND END PLAY TOOL
T-1501
SPEED SENSOR REMOVER
When used with T-1068

Also: 200, 200C, 200-4-R, 250, 350, 350-C
T-1063
PUMP SEAL INSTALLER
T-1502
SPEED SENSOR ROTOR INSTALLER KIT
T-1068
FRONT END PLAY TOOL * 245MM torque converter [Use with T-1055]
T-1503
STATOR SHAFT TEFLON SEAL INSTALLER RESIZER (4L60-E only)
T-1071- A
DIRECT CLUTCH ACCUMULATOR PISTON REMOVER AND INSTALLER
T-1517
AIR TEST PLATE (4L60 only)
T-1517- A T-1092
BEARING RACE INSTALLER AIR TEST PLATE (4L60-E only)
T-1527
OVERRUN CLUTCH INNER LIP SEAL INSTALLER PROTECTOR
T-0
T-1097
T-1528
FORWARD CLUTCH INNER LIP SEAL INSTALLER PROTECTOR
Also: 250, 350, 350C
58

GENERAL MOTORS
T-1529
700-R4 (4L60) (4L60-E) T-1574- B

TURBINE SHAFT SEAL RESIZER
T-1560
OUTPUT SHAFT SUPPORT FIXTURE
T-1702
PRESSURE REGULATOR VALVE SNAP RING INSTALLER
Also: 200-4R
T-1703
FRONT PUMP SPRING LOADER TOOL
T-1561
INTERMEDIATE BAND APPLY PIN GAUGE * Go / NO GO Gauge selects correct length of apply pin
T-1735
SERVO COVER DEPRESSOR * Use with pan on.
Also: 200, 200C, 200-4R
T-1571
SUN GEAR PULLER * Removes heat damaged sun gear when bonded to upper planetary set.
T-1891
TRANS OIL COOLER LINE DISCONNECT * 96-later light duty trucks.
T-2009
END PLAY ADAPTER For (4L60E)
TURBINE SHAFT TEFLON T-0 SEAL INSTALLER-RESIZER
T-2030
INPUT SHAFT TEFLON SEAL INSTALLER KIT Installs seals on direct/coast clutch assembly.
T-1574
(4L60 only)
* Prevents distortion during installation. * One tool will set all 4 rings. * See thru resizer prevents improper seal installation * Instructions included
T-1574-LONG
(416OE only)
* Prevents distortion during installation. * One tool will set all 4 rings. * See thru resizer extended length prevents improper seal installation * Instructions included
T-3423
T-1574- A
TURBINE SHAFT SEAL INSTALLER
30104- A
GOVERNOR BORE BUSHING (GM) [Use with T-0107, T-0107-D]
59

GENERAL MOTORS
(4L80-E) T-0128
REAR GEAR HOLDING FIXTURE ADAPTER
Use with T-0129
T-2054
REAR EXTENSION HOUSING OIL SEAL INSTALLER * Slip yoke design propshaft.
T-0129
REAR GEAR HOLDING FIXTURE
Use with T-0128
T-2057
DIRECT CLUTCH SPIRAL SNAP RING INSTALLER
T-1891
TRANS OIL COOLER LINE DISCONNECT 96-later light duty trucks
Also: 700-R4, (4L60) (4L60-E)
T-2058
OUTPUT SHAFT ASSEMBLY REMOVER INSTALLER Use with T-0154-HD and 4L60-E
T-2002
DIRECT CLUTCH ASSEMBLY REMOVER INSTALLER
T-2059 T-2025
BAND APPLY PIN CHECKING TOOL CLUTCH ASSEMBLY FINAL DRIVE REMOVER INSTALLER
Also: (4T60-E)
T-2901
TRANSMISSION HOLDING FIXTURE ADAPTER * Allows assembly & disassembly from a bench base.
T-0 T-0
T-2031
EXTENSION HOUSING OIL PUMP SEAL INSTALLER [Use with T-2054 for slip yoke prop application] [Use with T-0156-B]
T-2902
INTERMEDIATE CLUTCH PISTON COMPRESSOR
T-2053 T-2053
OIL PUMP ASSEMBLY REMOVER AND INSTALLER
60
T-2903
AUTOMATIC TRANSMISSION GENERAL TOOLS MOTORS (4L80-E) T-2927

OVER RUN CLUTCH PISTON LIP SEAL INSTALLER PROTECTOR * Protects inner seal when assembling.
OIL PUMP ASSEMBLY TEFLON SEAL INSTALLER AND RESIZER KIT 3 Piece Kit - installs each seal into its groove.
T-2904
CENTER SUPPORT TEFLON SEAL INSTALLER AND RESIZER KIT 3 piece kit
T-2928
FORWARD CLUTCH PISTON LIP SEAL INSTALLER PROTECTOR KIT * Protects inner and outer seals while servicing.
T-2905
INTERMEDIATE CLUTCH PACK ALIGNMENT TOOL
T-2930
FORWARD & DIRECT CLUTCH INNER SEAL PROTECTOR INSTALLER [Use with T-2924, T-2925]
T-2962 T-2917
AIR TEST PLATE PUMP ALIGNMENT BAND
T-2924
DIRECT CLUTCH OUTER SEAL PROTECTOR INSTALLER [Use with T-2930, T-2925]
T-2974
TURBINE SHAFT TEFLON SEAL INSTALLER-RESIZER KIT (6 pieces) * Helps in installing each seal into its groove & sizes or compresses each seal into the grooves.
T-0
T-2925
SECOND CLUTCH INNER SEAL PROTECTOR INSTALLER
T-2995
REAR BUSHING CASE BORING TOOL
T-2995-SL Replacement Sleeves
T-2926
FOURTH CLUTCH PISTON & HOUSING LIP SEAL INSTALLER PROTECTOR KIT * Protects the inner & outer seals when servicing the 4th clutch piston.
T-3422
CENTER SUPPORT THREAD REAMER * Includes reamer and gauge pin.
61

GENERAL MOTORS
POWERGLIDE T-0033
HEAVY DUTY FRONT PUMP PULLER
T-0153- HD
FRONT PUMP AND SPEEDOMETER GEAR REMOVER
T-0033- A
T-0160- A
EXTENSION HOUSING BUSHING REMOVER INSTALLER AND OUTPUT SHAFT SUPPORT FIXTURE * Eases & speeds process.
T-0085
T-1001
T-0131
T-1097
Also: 250, 350, 350C, 375, 400, 700-R4
T-0134
FRONT PUMP SEAL INSTALLER * Small shaft
SATURN TOOLS
T-3530
CLUTCH PISTON SEAL INSTALLER SET
T-0150
REAR CLUTCH SPRING COMPRESSOR SERVO PISTON SEAL INSTALLER SET
T-3531
JF403-E
(Nissan Transmission Used By GM - Geo)
T-0 T-0
T-1092
T-2210
SIDE BEARING PULLER PILOT [Front axle - use with universal two jaw puller]
T-1208
AXLE SHAFT SEAL INSTALLER [Use with T-1093]
T-2211
SERVO PISTON CLUTCH SPRING COMPRESSOR
T-2208
BEARING PULLER BRIDGE
T-2212
BEARING CUP REMOVER
62
FORD OLD TO NEW TRANSMISSION CONVERTIONS A4LD-Elec ................(4R44E) ..................................(4R55E) A4LD 5 Spd..............(5R55E) AOD-EW ..................(4R70W) 4 Spd FWD ..............(CD4E) AXOD-E ....................(AX4S) 4 Spd FWD ..............(AX4N) 4EAT Probe..............(G4A-EL) F4EAT Escort ..........(F4A-EL) GF4EAT ....................(GF4A-EL) 4F20-E Villager ........(RE4F04A)
SPECIFIC TOOLS FOR: FORD
Transmission Type
a. C-3, A4LD (4R44E) (4R55E) (5R55E) (5R55N) ....64-67 b. C-4, C-5 ................................................68 c. C-6........................................................69-70 d. AOD, AOD-E, AOD-EW (4R70W) ......71-75 ATX 82-84 f. AXOD, AXOD-E (AX4S) (AX4N) ........79-82 g. E4OD....................................................83-84 h. 4EAT (G4A-EL), F4EAT (F4A-EL) (G-4EAT) ..............................................85-86 i. (CD4E)..................................................87-88 j. 4F20-E (RE4F04A) ..............................89
e.
FEATURED PRODUCTS
T-0033
HEAVY DUTY FRONT PUMP REMOVER CLUTCH REMOVER INSTALLER See Page 84
T-2805
See Page 79
T-0004
FORD TRANSMISSION TOOLS-EQUIP
See Page 71
See Page 87
T-2400
See Page 81
T-1600-K
T-0158-HD
A.
B.
C.
63

FORD
C3, A4LD (4R44E) (4R55E) (5R55E) (5R55N) T-0030- A T-0409

H GAUGE UNIVERSAL FRONT PUMP CLEARANCE GAUGE OVERRUN CLUTCH GUIDE For: A4LD, 4R44E, 4R55E, 5R55E
T-0130
BOOT TYPE EXTENSION HOUSING SEAL INSTALLER
T-0414
FRONT SERVO COVER COMPRESSOR
T-0137
EXTENSION HOUSING SEAL REPLACER For: A4LD, 4R44E, 4R55E
T-0417
AIR TEST PLATE (C3 Only)
T-0159
EXTENSION HOUSING BUSHING REMOVER AND INSTALLER (C3 Only)
T-0429
OIL PUMP ALIGNING GAUGE KIT (5 PIECES) Gauges Available Individually A B C D E
T-0168- A
BELL HOUSING TO PUMP ALIGNMENT TOOL
T-0429- A T-0429- B T-0429- C T-0429- D T-0429- E T-0431

CLUTCH INSTALLER GUIDE Also for A4LD, 5R55E and 4R55E
T-0168- B
PUMP TO GEAR ALIGNMENT TOOL

Up to 90
T-0168- C
HEAVY DUTY PUMP TO GEAR ALIGNMENT TOOL
Up to 90
T-0168- CU
FRONT PUMP ALIGNMENT TOOL
90 up
T-0432
PNP REMOVER AND REPLACER For A4LD. Also: AOD
T-0168- K
BELL HOUSING TO PUMP & PUMP TO GEAR ALIGNMENT TOOL KIT
64

FORD
C3, A4LD (4R44E) (4R55E) (5R55E) (5R55N) T-0468 T-0437

INNER SEAL PROTECTOR For A4LD FRONT PUMP SEAL INSTALLER For: A4LD (5R55E)
T-0438
MANUAL LEVER OIL SEAL INSTALLER For: A4LD (4R44E) (4R55E) (5R55E)
Also: AOD, AOD-E, E40D
T-0469
PUMP SEAL STAKING TOOL For: A4LD (5R55E)
T-0439
PISTON INNER SEAL PROTECTOR For: (4R44E) (4R55E) (5R55E) (5R55N) (5R55S) (5R55W)
T-0480
A4LD HOLDING FIXTURE ADAPTER For: A4LD
T-0440
OUTER SEAL PROTECTOR For: A4LD (4R44E) (4R55E) (5R55E)
T-0481
GAUGE BAR For: A4LD
T-0443
HOUSING BUSHING INSTALLER For: A4LD (4R44E) (4R55E) (5R55E) (5R55N) (5R55S) (5R55W)
T-0484
VALVE BODY GUIDE .235 PIN For: (4R44E) (4R55E) (5R55E)
T-0
T-0450
END PLAY CHECKING TOOL For all Ford transmissions except ATX
T-0485
VALVE BODY GUIDE .248 PIN For: (4R44E) (4R55E) (5R55E)
T-0486
COAST CLUTCH SEAL SIZING TOOL For: (4R44E) (4R55E) (5R55E)
T-0487
DIRECT CLUTCH SEAL SIZING TOOL For: (4R44E) (4R55E) (5R55E)
65

FORD
C3, A4LD (4R44E) (4R55E) (5R55E) (5R55N) T-0488 T-0500

For: (4R44E) (4R55E) (5R55E) TSS GAUGE PUMP BEARING INSTALLER For: (5R55E) [Use with T-1215 bushing driver handle]
T-0489
CONVERTER GUIDE PIN For: (4R44E) (4R55E) (5R55E)
T-0490
FRONT PUMP SEAL SIZER For:(4R44E) (4R55E) (5R55E)
T-0501
CENTER SUPPORT BEARING INSTALLER For: (5R55E) [Use with T-1215 bushing driver handle]
T-0492
TRANSMISSION TEST PLATE For: (4R44E) (4R55E)
T-0502
FORWARD CLUTCH BEARING INSTALLER For: (5R55E) [Use with T-1215 bushing driver handle]
T-0493
SERVO COVER COMPRESSOR For: (4R44E) (4R55E) (5R55E)
T-0494
PUMP SEAL STAKING TOOL ADAPTER For: (4R44E) (4R55E) (5R55E)
T-0503
SLEEVE, ONE WAY CLUTCH For: (5R55E) [Use with T-0504]
T-0 T-0504
PUSHER, ONE WAY CLUTCH For: (5R55E) [Use with T-0503]
T-0495
GOVERNOR BORE CASE SLEEVING TOOL [Use with T-0495-SL]
T-0506
TRANSMISSION BELL HOUSING GUIDE PIN For (4R44E) (4R55E) ( 5R55E
T-0495- SL
GOVERNOR BORE BUSHING REPLACEMENT [For T-0495]
T-0507
SELECTING GAUGE
T-0497
SERVO COVER COMPRESSOR For: (5R55E)
T-0
For: A4LD, (4R44E) (4R55E) (5R55E)
T-0508
HOUSING BUSHING REMOVER For: C3, A4LD
66

FORD
C3, A4LD (4R44E) (4R55E) (5R55E) (5R55N) T-0518 T-0509

REVERSE DRUM 1 WAY CLUTCH PUSHER For: (4R55E) (5R55E) SERVO COVER COMPRESSOR For: (5RR5N)
T-0510
REVERSE DRUM 1 WAY CLUTCH PUSHER For:(4R55E) (5R55E)
T-0519
FLEX PLATE ALIGNER For: (5R55N)
T-0520
OUTPUT FLANGE INSTALLER For: (5R55N)
T-0511
OUTPUT SHAFT BEARING INSTALLER For: (5R55E)
T-0521
AIR TEST PLATE For: (5R55N)
T-0512
CONVERTER SEAL INSTALLER For: (5R55E)
T-0522
OUTPUT FLANGE REMOVER For: (5R55N)
T-0513 TRANSMISSION T-0516 PUMP PULLER

For: (5R55N)
T-2324
BAND ADJUSTER WRENCH KIT * Set at 10 foot pounds For: A4LD (4R44E) (5R55E) Also: C6
T-0514
PUMP ALIGNMENT PINS For: (5R55N) (5R55S) (5R55W)
T-0515
OIL PUMP TO TRANS CASE ALIGNMENT PINS For: (5R55N) (5R55S) (5R55W)
T-2601
PUMP SEAL STAKING TOOL For: A4LD
T-0 T-0516
GAUGE BAR For: (5R55N)
T-2617
VALVE BODY TEST PLATE For: A4LD
T-5015
OVERDRIVE SPRAG INSTALLER For: A4LD
T-0517
CUSHION SPRING COMPRESSOR For: (5RR5N)
67

FORD
C4, C5 T-0033
T-0163- A
HEAVY DUTY VACUUM PUMP
T-0033- A
T-0163- C
PRESSURE GAUGE 0 - 100 POUNDS
T-0130
T-0163- D
T-0131
EXTENSION HOUSING SEAL INSTALLER For: C4 Only
T-0450
END PLAY CHECK TOOL All Ford Trans except ATX
T-0132
FRONT PUMP SEAL INSTALLER For: C4 Only
T-0154- HD
HEAVY DUTY SLIDE HAMMER SET
T-1028
REVERSE CLUTCH LIP SEAL INSTALLER AND PROTECTOR For: C5 Only 81-current
T-0156- A
HOLDING FIXTURE WITH BASE * Bench mounts * 360 degree swing
T-0156- AF
WITHOUT BASE
T-1890
COOLER LINE QUICK DISCONNECT TOOL * Removes push lock connectors found at both the radiator & transmission connections on 83 thru current Ford vehicles & the 82 Lincoln Continental overdrive trans.
T-0158- HD
CLUTCH DRUM SPRING COMPRESSOR
T-0160- A
EXTENSION HOUSING BUSHING REMOVER INSTALLER AND OUTPUT SHAFT SUPPORT FIXTURE
68

FORD
C6 T-0033
T-0156- A
T-0156- AF T-0033- A
HEAVY DUTY FRONT PUMP REMOVER HOLDING FIXTURE WITHOUT BASE
T-0157
UNIVERSAL QUICK LOCK CLUTCH SPRING COMPRESSOR
T-0130
T-0157-K
Compression ring kit for T-0157
T-0158- HD
T-0133
REAR SEAL INSTALLER
T-0161- A T-0136
FRONT PUMP OIL SEAL INSTALLER EXTENSION HOUSING BUSHING REMOVER AND INSTALLER
[Ford] Also: 727, FMX, E4OD FORD TRANSMISSION TOOLS-EQUIP
T-0152
T-0163- A
VACUUM PUMP HEAVY DUTY
T-0163- C
T-0163- D T-0
69

FORD
C6 T-0427
AIR TEST PLATE
Also: E4ODD, 4R70W
T-0496
BUSHING INSTALLER REMOVER
T-0428
T-1052
UNIVERSAL TORQUE CONVERTER LEAK TESTER
RPK-1052
REPLACEMENT FOR T-1052
T-0442
CONVERTER CLUTCH HOLDING TOOL
Also: AOD, AOD-E, AXOD, ATX, 4R70W
T-1890
COOLER LINE QUICK DISCONNECT TOOL * Removes push lock connectors found at both the radiator & transmission connections on 83 thru current Ford vehicles & the 82 Lincoln Continental overdrive trans. Order T-1889 for replacement part.
T-0444
SEAL PROTECTOR
Also: E40D
T-0450
END PLAY CHECKING TOOL
All Ford Transmissions except ATX
T-2321
Also: CD4E
T-0479
VRV SETTING BLOCK
Also: E40D
MANUAL LEVER SEAL INSTALLER
70

FORD
T-0033
AOD, AOD-E, AOD-EW (4R70W) T-0156- A

T-0156- AF
ABOVE HOLDING FIXTURE WITHOUT BASE
T-0033- A
T-0157
UNIVERSL QUICK LOCK CLUTCH SPRING COMPRESSOR
T-0157- K
COMPRESSION RING KIT
T-0131
T-0158- HD
T-0132
FRONT PUMP SEAL INSTALLER Does not work on 4R70W
T-0160- A
EXTENSION HOUSING BUSHING REMOVER INSTALLER AND OUTPUT SHAFT SUPPORT FIXTURE * Eases & speeds process
T-0136
FRONT PUMP OIL SEAL REPLACER
Also: C6, E4OD, 4R70W
T-0220-AOD
BUSHING DRIVER KIT
T-0154- B
10mm SLIDE HAMMER ADAPTERS
T-0154- HD
T-0428
EXTENSION HOUSING SEAL REPLACER For: (4R70W)
Also: C6, E4OD
71

FORD
AOD, AOD-E, AOD-EW (4R70W) T-0431

CLUTCH INSTALLER GUIDE Also for A4LD, 5R55E and 4R55E
T-0442
Also: C6, AXOD, ATX
T-0432
PNP REMOVER AND INSTALLER
T-0446
OIL PUMP BUSHING INSTALLER
T-0436
UNIVERSAL OIL SEAL REMOVER
T-0447
OIL PUMP BUSHING REMOVER For AOD, AOD-E, (4R70W)
T-0438
MANUAL LEVER OIL SEAL INSTALLER For AOD, AOD-E
Also: AL4D, (4R4E) (4R55E) (5R55E), E4OD
T-0450
T-0441
ONE WAY CLUTCH TOOL
T-1600- K
LIP SEAL INSTALLER PROTECTOR KIT Prevents cutting and rolling during installation. A complete set to insure proper installation of liip seals. Available Individually (see next page)
72

FORD
T-1601
For: AOD, AOD-E

DIRECT DRIVE SOLID SEALING RING INSTALLER KIT
THROTTLE VALVE CABLE GAUGE
T-1602
THROTTLE VALVE GAUGE BLOCK
T-1619 T-1603
REAR CASE BUSHING R&R SERVO REMOVER INSTALLER OVERDRIVE & LOW-REVERSE SERVO For: AODE Also for AX4N Coast
T-0
For: AOD-E
T-1605
TORQUE CONVERTER CHECKING TOOL
T-1624
DIRECT CLUTCH INNER LIP SEAL INSTALLER PROTECTOR
T-1606
OIL PRESSURE GAUGE SET For: AOD
T-1625
FORWARD CLUTCH INNER LIP SEAL INSTALLER PROTECTOR
T-1613
T-0
CLUTCH PISTON LIP SEAL PROTECTOR For AOD, AOD-E, 4R70W
T-1626
REVERSE CLUTCH OUTER LIP SEAL INSTALLER PROTECTOR
T-1617
AIR TEST PLATE For: AOD
T-1617- A
AIR TEST PLATE For: AOD-E
T-1627
REVERSE CLUTCH INNER LIP SEAL INSTALLER PROTECTOR
73

FORD

DIRECT CLUTCH OUTER LIP SEAL INSTALLER PROTECTOR
T-1641
VALVE BODY GUIDE PINS
T-1629
INTERMEDIATE CLUTCH LIP SEAL INSTALLER PROTECTOR
T-1643
END PLAY AND CLEARANCE GAUGE BAR
T-1630
FORWARD CLUTCH OUTER LIP SEAL INSTALLER PROTECTOR
T-1665
CASE REAR BUSHING INSTALLER
T-1632
SERVO PISTON REMOVER
T-2329
SUN GEAR BUSHING INSTALLER For: AOD only
T-1695 T-1633
SERVO PISTON SELECTOR GOVERNOR BORE CASE SLEEVING TOOL KIT For: AOD, AOD-E [Use with T-1695-SL]
T-1695- SL T-1634
SERVO PISTON REMOVER INSTALLER For: AOD-E BUSHING REPLACEMENT [Use with T-1695] AOD only
T-1690-SLE
AODE Replacement for T-1695
74

FORD
T-1890

OIL COOLER LINE DISCONNECT TOOL
COOLER AND FUEL LINE DISCONNECT TOOL * Removes push lock connectors found at both the radiator & transmission connections on 83 thru current Fords & 82 Lincoln overdrive. GEAR POSITION SENSOR ADJUSTER (TRS ALIGNMENT TOOL)
Also: AXOD, ATX
T-2802- A T-2142
AODE INPUT SHAFT SIZING RING TOOL
Also: AXOD, AXOD-E, AX4N, E4OD, AOD, AODE
T-2327
MLPS ALIGNMENT TOOL For 4R70W, 4R44E,
4R55E, A4LD Also: E4OD
T-2806
PUMP PULLER ADAPTERS Works on (E4OD) (4R70W) (AOD) (AODE)
T-2408
OUTPUT SEAL INSTALLER For AOD, AOD-E
Also: E4OD
75

FORD
ATX T-0154- HD
T-0452
CONVERTER REACTOR SUPPORT TOOL KIT
T-0157
UNIVERSAL QUICK LOCK SPRING COMPRESSOR
T-0453
BEARING INSTALLER
T-0157- K
COMPRESSION RING KIT [ For: T-0157]
T-0158
AUTOMATIC TRANSMISSION CLUTCH SPRING COMPRESOR KIT * For foreign & domestic * Removes clutch pistons * Adapters included for AOD, AXOD, ATX. * Can be used on clutch drums with center shafts. * Instructions included
T-0458
END PLAY CHECK TOOL
T-0460
BEARING REMOVER For: ATX (FLC)
Also: AXOD, 4EAT type F, G
T-0158- HD
T-0461
DIFFERENTIAL INSTALLER
Also: 4EAT
T-0
CLUTCH DRUM SPRING COMPRESSOR * Most economical universal unit. * Longer legs for deep drums. * Mounts directly on work bench or vise
T-0442
Also: C6, AOD, AOD-E, (4R70W), AXOD
76

FORD
ATX T-0464
BEARING CONE INSTALLER For: ATX 1.25 I.D. 8.0 66 thru 79
Also: 4EAT
T-0099
T-0467
CONVERTOR SEAL INSTALLER
Also: 4EAT TYPE F
T-0131
T-0470
TV LINKAGE ADJUSTMENT TOOL
T-0132
T-1641
T-0133 T-1643
END PLAY AND CLEARANCE GAUGE BAR REAR SEAL INSTALLER
T-0161- A T-1817
AIR TEST PLATE WITH BOLT KIT EXTENSION HOUSING BUSHING REMOVER AND INSTALLER
Also: C6, 727, E4OD
T-0450 T-1863
FRONT PUMP SEAL INSTALLER END PLAY CHECKING TOOL
77

FORD
ATX T-1864
DIFFERENTIAL ROTATOR AND AXLE REMOVER
T-2323
CONVERTER HUB SEAL INSTALLER
T-2341
DIFFERENTIAL SEAL INSTALLER
T-1890
COOLER AND FUEL LINE DISCONNECT TOOL * Removes push lock connectors found at both the radiator & transmission connections on 83 thru current Fords & 82 Lincoln overdrive.
Also: 4EAT type F, G
T-2410
FRONT HUB INSTALLER
T-0
T-2322
THROTTLE SHAFT SEAL INSTALLER
T-2411
FRONT HUB REMOVER
Also: CD4E
T-2416
OIL COOLER LINE DISCONNECT TOOL
Also: AOD, AXOD
78

FORD
T-0004
AXOD, AXOD-E (AX4S) (AX4N) T-0460

BEARING REMOVER For AXOD
T-0004- RT
REPLACEMENT TIPS FOR T-0004
Also: ATX, 4EAT (type F,G)
T-1619
SERVO REMOVER INSTALLER OVERDRIVE & LOW-REVERSE SERVO For AX4N Coast Also for: AODE
T-0156- A
T-0156- AF
T-1650
CONVERTER SEAL REMOVER For (AX4N)
T-0436
UNIVERSAL OIL SEAL REMOVER
T-1651
LUBE TUBE REMOVER For (AX4N)
T-0442
T-1652
LOW AND INTERMEDIATE CLUTCH PISTON LIP SEAL PROTECTOR For (AX4N)
Also: C6, AOD, AOD-E (4R70W), ATX
T-0450
T-1653
AIR TEST PLATE For (AX4N)
T-1654
GASKET ONLY
79

FORD

REVERSE CLUTCH PLANET ASSEMBLY COLLET For (AX4N)
T-1662
REVERSE PISTON LIP SEAL PROTECTOR For (AX4N)
T-1656
LUBE TUBE SEAL REPLACER For (AX4N)
T-1664
DRIVER SPROCKET WHEEL INSTALLER For (AX4N) (AX4S)
T-1657
FRONT CLUTCH LOADING TOOL SCREW For (AX4N)
T-2325
OUTPUT SEAL INSTALLER
T-1658
OUTPUT SHAFT SEAL REPLACER PILOT For (AX4N)
Also: CD4E
T-1659
BEARING REMOVER
T-2397
PUMP BODY GUIDE PIN For (AXOD)
For (AX4N)
T-1660
T-0
INTERMEDIATE CLUTCH BALANCE PISTON LIP SEAL PROTECTOR For (AX4N)
T-2398
PUMP BEARING-SEAL REMOVER For (AX4N) (AX4S)
T-1661
SHIM SELECTION GAUGE For (AX4N)
T-2399
PUMP BEARING-SEAL INSTALLER For (AX4N) (AX4S)
80

FORD
T-2400
A

STATOR AND DRIVEN SPROCKET BEARING INSTALLER
LIP SEAL INSTALLER PROTECTOR KIT Available Individually
T-2400- A
B
Direct Clutch Piston Protector
T-2400- B
Seal Protector - Reverse
T-2406
DIRECT INTERMEDIATE CLUTCH BUSHING INSTALLER
T-2400- C
Forward/Intermediate Clutch Seal Protector
T-2401
OVERDRIVE SERVO ROD TOOL
T-2407
VALVE AND PUMP SHAFT BODY GUIDE PINS * ESSENTIAL: Prevents misalignment of oil pump and valve body.
T-2402
FRONT CLUTCH LOADING TOOL
T-2409- F
T-0156-BB T-2403
LOW INTERMEDIATE SERVO ROD TOOL HOLDING FIXTURE BASE FOR T-2409- F
T-2410
FRONT HUB INSTALLER
T-2404
FRONT PLANETARY BUSHING INSTALLER
T-2411
FRONT HUB REMOVER
81

FORD

BIMETAL HEIGHT GAUGE TOOL
T-2421
OUTPUT SHAFT SEAL INSTALLER
T-2416
OIL COOLER LINE DISCONNECT TOOL Use with T-1889 Replacement Kit
Also: AOD, ATX
T-2433
REVERSE CLUTCH FEED OIL PIPE SEAL INSTALLER For: AXOD
T-2463 T-2417
AIR TEST PLATE For: AXOD CONVERTER OIL SEAL INSTALLER
T-2470 T-2417- A
AIR TEST PLATE For: AXOD-E REVERSE DRUM & PLANETARY GEARS REMOVER-INSTALLER
Ford Transmission Tools-Equip
T-2418
CONVERTER GUIDE SLEEVE
T-2494
OIL PUMP NEEDLE BEARING AND SEAL TOOL * For bearing replacement
[Use with T-0450]
T-0
T-2420
END PLAY TOOL
T-2495
VALVE BODY COVER PUMP DRIVE SHAFT BORE REPAIR TOOL
T-2495- SL
BUSHING REPLACEMENT For: T-2495
82

FORD
E40D T-0033
UNIVERSAL PUMP REMOVER * Quickly removes conventional type pumps without damage.
T-0438
OIL SEAL INSTALLER
Also: AOD, AOD-E, A4LD, (5R55E) (4R44E) (4R55E)
T-0444
SEAL PROTECTOR
T-0034
UNIVERSAL SEAL PULLER * Insert tip of the tool behind seal & leverage works for you. * Eliminates hammering & digging.
Also: C6
T-0450
T-0133
T-0479
VRV SETTING BLOCK
Also: C6
T-0136
FRONT PUMP OIL SEAL INSTALLER
T-2408
OUTPUT SHAFT BUSHING INSTALLER
Also: C6, AOD, AOD-E, (4R70W)
T-0161- A
T-0428
Also: C6, (4R70W)
83

FORD
E4OD T-2409
REAR CASE BUSHING REPLACER SET
T-2804
CLUTCH SPRING FIXTURE * All metal
Also: C6
T-2412
OUTPUT SHAFT BUSHING INSTALLER
T-2805
CLUTCH REMOVER INSTALLER * Works on new & older clutch drums.
T-2716-A
RETURN SPRING COMPRESSOR Low & Reverse Brake Piston 89- current
T-2806
PUMP PULLER ADAPTERS Works on (E4OD) (4R70W) (AOD) (AODE)
T-2800- F
HOLDING FIXTURE WITHOUT BASE [Use with base T-0156-BB]
T-2808
PRESSURE REGULATOR SNAP RING INSTALLER
T-0156- BB
HOLDING FIXTURE BASE
T-2817
AIR TEST PLATE
T-2801
T-0
OIL FILLER TUBE INSTALLER
T-2802- A
GEAR POSITION SENSOR ADJUSTER
Also: AOD, AOD-E, AXOD, AXOD-E
T-2862
ALIGNMENT BAND
T-2803
FRONT PUMP ALIGNING PIN
84

FORD
4EAT (G4A-EL), F4EAT (F4A-EL), (G-4EAT) T-0450 T-1641

END PLAY CHECKING TOOL VALVE BODY GUIDE PINS For 4EAT Type F, G
Also: AOD, AOD-E
T-0460
BEARING REMOVER For 4EAT-Types F, G
T-1643
END PLAY AND CLEARANCE GAUGE BAR For 4EAT
Also: AOD, AOD-E
Also: AXOD, ATX
T-0461
DIFFERENTIAL INSTALLER For 4EAT-Types F, G
T-0
T-2708
CONVERTER SEAL INSTALLER For 4EAT Type F, G
Also: ATX
T-0464
BEARING CONE INSTALLER For 4EAT-Types F, G 1.25 I.D. 8.0 * 1965 Thru 1979
Also: ATX (FLC)
T-2709
PRELOAD TORQUE ADAPTER For 4EAT Type F, G
T-0467
CONVERTER SEAL INSTALLER For 4EAT-Type F
Also: ATX
T-2710
DIFFERENTIAL BEARING CUP INSTALLER For 4EAT Type F, G
T-0471
OIL SENSOR REMOVER INSTALLER For 4EAT Type G
85

FORD
4EAT (G4A-EL), F4EAT (F4A-EL), (G-4EAT) T-2717 T-2712

TORQUE CONVERTER LEAK CHECK ADAPTER For 4EAT Type G Use with T-1052 AIR TEST PLACE For: (G4AEL)
T-2712-A
TORQUE CONVERTER LEAK CHECK ADAPTER For 4EAT Type F Use with T-1052
T-2718
T-0
LOW REVERSE CLUTCH SPRING COMPRESSOR For: F-4EAT (G4A-EL)
T-2713
LIP SEAL INSTALLER PROTECTOR For 4EAT Type F, G * Installs reverse piston & low-reverse clutch piston lip seals
T-2722
SHIM SELECTION SET For 4EAT Type F, G
T-2714
COASTING PISTON LIP SEAL INSTALLER PROTECTOR For 4EAT Type F, G
T-2723
SHIM SELECTION GAUGE For 4EAT Type F
T-2724
A
T-2715
TURBINE SHAFT HOLDER For 4EAT Type G
SEAL PROTECTOR SET (3 Piece) For 4EAT Type F AVAILABLE INDIVIDUALLY
T-2724-A T-2724-B T-2724-C T-3425

COOLER LINE BANJO FITTING For: 4EAT
T-2716- A
RETURN SPRING COMPRESSOR * Low & reverse brake piston
Also: (4F20-E), Mazda, Nissan, Infinite, BMW, Mercedes
86

FORD
CD4E T-0450
T-2306
SHIFTER SHAFT ALIGNMENT TOOL
T-2301
CLUTCH PISTON LIP SEAL PROTECTOR KIT
T-2307
SPRAG INSTALLER
T-2302
CONVERTER SEAL INSTALLER
T-2308
NEEDLE BEARING INSTALLER
T-2303
NEEDLE BEARING REMOVER INSTALLER
T-2309
SERVO COVER REMOVER AND INSTALLER
T-2304
TRANSMISSION MOUNTING BRACKET
T-2310
SERVO PISTON ROD SELECTION TOOL
T-2305
OIL PUMP REMOVAL BOLTS
T-2311
87

FORD
CD4E T-2312
PUMP ALIGNMENT PINS
T-2319
END PLAY CHECKING TOOL SLEEVE
T-2313
GAUGE BAR
T-2320
DIRECT CLUTCH PISTON LIP SEAL PROTECTOR
T-2314
PRELOAD TOOL ADAPTER ALIGNER SET
T-2321
MANUAL LEVER SEAL INSTALLER
Also: C6
T-2315
AIR TEST PLATE
T-2322
THROTTLE SHAFT SEAL INSTALLER
T-2316
GASKET FOR T-2315
Also: ATX
T-2317
GAUGE BAR SPACER SET
T-2325
OUTPUT SEAL INSTALLER
Also: AXOD
T-0
T-2725 T-2318
LUBE TUBE INSTALLER SET MLPS ALIGNMENT TOOL
T-2726
CONVERTOR SEAL REMOVER
88

FORD
T-0450
4F20E (RE4FO4A) T-0476

SHIFT LEVER SEAL INSTALLER For 4F20E
T-0472
GEAR PISTON SENSOR ADJUSTER For 4F20E
T-0477
DIFFERENTIAL SEAL INSTALLER For 4F20E
T-0473
DIFFERENTIAL ROTATOR For 4F20E
T-0478
CLUTCH SPRING COMPRESSOR BAR For 4F20E
T-0474
BEARING RETAINER INSTALLER For 4F20E
T-0483
END PLAY CHECKING TOOL For 4F20E
T-0475
SHIM SELECTION BOLT SET For 4F20E
T-3425
COOLER LINE BANJO FITTING
89
CHRYSLER OLD TO NEW TRANSMISSION CONVERTIONS 404 ............................(30TH) 413, 470....................(31TH) 500................(40RH) (42RH) 518 ............................(46RH) 618 ............................(47RH) 604 ............................(41TE) 604 LD ......................(40TE) 604 AWD ..................(41AE) 606 ............................(42LE) 727...............(36RH) (37RH) 904 ............................(30RH) 998 ............................(31RH) 999 ............................(32RH)
SPECIFIC TOOLS FOR: CHRYSLER
Transmission Type
a. 404 (30TH), 413, 470 (31TH) ........98 b. 500 (40RH) (42RH) (42RE) (44RE), 518 (46RH) (46RE), 618 (47RH) (47RE) ........................99 c. 604, 604-E (40TE) (41TE) (41AE), 607..................................................100-101 d. 606 (42LE).....................................102-103 e. 727 (36RH) (37RH), ......................104 f. 904 (30RH), 998 (31RH), 999 (32RH). ....................................105-106
FOR: MISCELLANEOUS
Transmission Type Toyota, Mitsubishi/Hyundai, Mercedes, Renault, Volvo ..........107
FEATURED PRODUCTS
T-0033
UNIVERSAL PUMP REMOVER
T-1302
HEAVY DUTY DIRECT CLUTCH SPRING COMPRESSOR See Page99
T-1307
SPLINE ALIGNMENT TOOL
CHRYSLER TRANS. TOOLS-EQUIP
See Page 105
See Page 99
T-1420-K
OVERDRIVE REVERSE REACTION PLATE SPRING COMPRESSOR KIT
T-0030-A
H GAUGE UNIVERSAL FRONT PUMP CLEARANCE GAUGE See Page105
T-1435-A
TRANSFER SHAFT BEARING SNAP-RING REMOVER INSTALLER
See Page 100
See Page100
90

CHRYSLER
T-0033
UNIVERSAL PUMP REMOVER
404 (30TH), 413, 470 (31TH) T-1452

BEARING AND SEAL INSTALLER (31TH) * Use with T-3208 to install differential bearing. Used on rear wheel blue hub Also: (41AE) seal.
* Quickly removes conventional type pumps without damage.
T-1406
DIFFERENTIAL BEARING CONE REMOVER
T-1453
BEARING CUP AND CONE REMOVER INSTALLER KIT * New bronze collet for strength.
T-1409
OVERRUN CLUTCH ASSEMBLY INSTALLER BEARING CUPS IN: * Transfer shaft bearing cup retainer
* * * * Differential bearing cup retainer Output bearing cups Governor support retainer Extension housing
Also: 604, 604-E, 607
BEARING CONES IN:

* Transfer shafts * Differential assembly * Rear carrier * Output shaft gear * Transfer shaft gear * Rear annulus gear
T-1418
TRANSFER SHAFT & DIFFERENTIAL GEAR BEARING CUP (RACE) AND EXTENSION REMOVER
T-1454
OUTPUT AND TRANSFER SHAFT GEAR REMOVER * Fits both early & late models
T-1432
BEARING PULLER SET For (31TH) * Removes rear carrier, output gear, and transfer gear bearing cones.
Also: 604, (41TE), (41AE) (42LE)
T-1460
OUTPUT AND TRANSFER GEAR HOLDER REMOVER & INSTALLER * Up to 1979 1/2
T-1427
AIR TEST PLATE
T-1462
ADAPTER FOR T-1407 AND T-1460 * For use on 1979 1/2 and up
PHOTO NOT AVAILABLE
T-1448
DIFFERENTIAL SEAL AND CUP INSTALLER
T-3208
UNIVERSAL DRIVE HANDLE For (31TH) [Use with T-1452]
For (31TH) * Installs differential, extension housing oil seals & differential bearing cups. (Also: 604, (40TE)(41TE)(41AE)
91

CHRYSLER
500 (40RH) (42RH) (42RE) (44RE), 518 (46RH) (46RE), 618 (47RH) (47RE) T-1301
O.D. PISTON SHIM AND INTER. SHAFT SPACER GAUGE For: 500, 518 only
T-1321
COOLING LINE DISCONNECT TOOL From RWD vehicles 97 up Both 3/8 & 1/2 lines
T-1302
HEAVY DUTY DIRECT CLUTCH SPRING COMPRESSOR Part of T-1318 For: 500, 518 only
T-1322
OVERDRIVE PISTON SEAL INSTALLER For 4 Sp. RWD 96-up
T-1323
OUTPUT SHAFT BUSHING REMOVER For (46RE)
T-1307
SPLINE ALIGNMENT TOOL Part of T-1318 For: 500, 518 only
T-1441
RETAINING CLIP INSTALLER- REMOVER For (42RE) (44RE) (46RE) (47RE) * Used to compress front clutch assembly.
Also: 727 (36RH), (32RH)
T-1317
AIR TEST PLATE
Also: 727, 904
T-3229 T-1318
SPRING COMPRESSOR ALIGNMENT SHAFT * Disassemble & reassemble the overdrive unit For: 500, (40RH) (42RH) (46RH) (46RE) FRONT PUMP OIL SEAL INSTALLER For (42RE) (44RE)
Also: 604 (41TE), (42LE), (30RH)
T-1450
REAR EXTENSION HOUSING SEAL INSTALLER For (42RE) (44RE) (46RE) (47RE) [Use with T-3208]
Also: 904, (32RH), ( 36RH),
T-1319
T-0
TRANS BAND ADAPTER For (42RE) (44RE) (46RE) (46RH) (47RE) * Use with torque wrench to adjust transmission bands
Also: 727 (36RH), 904 (30RH) (32RH)
T-3208
UNIVERSAL DRIVE HANDLE [Use with T-1450 and T-1320]
T-1320
FRONT PUMP SEAL INSTALLER For (42RE) (44RE) (46RE) (47RE) [Use with T-3208]
Also: (36RH)
T-3210
* THRUST PLATE GAUGE BAR Use with a dial caliper or depth gauge to select the proper thrust plate.
92

CHRYSLER
604, 604-E (40TE) (41TE) (41AE), 607 T-1436 T-1420- K

OVERDRIVE REVERSE REACTION PLATE SPRING COMPRESSOR KIT TRANSFER AND OUTPUT GEAR BEARING CONE INSTALLER
T-1430
INPUT CLUTCH OUTER LIP SEAL INSTALLER PROTECTOR
T-1437
2-4 PISTON SPRING COMPRESSOR * Center bolt to be used with T-1431 and T-1443
Also: (42LE)
T-1431
OVERDRIVE AND REVERSE REACTION PLATE SPRING COMPRESSOR [Use with center bolt from T-1437 and T-1443]
Also: (42LE)
T-1438
UNDER DRIVE SPRING RETAINER SEAL INSTALLER
T-1432
BEARING CONE REMOVER SET * Can be used with T-1447 on 41TE
T-1439
TRANSFER SHAFT BEARING CONE INSTALLER
T-1442
AIR TEST PLATE
T-1433
FRONT BEARING CUP AND TRANSFER SHAFT REMOVER AND INSTALLER
T-1443
OVERDRIVE AND REVERSE SPRING COMPRESSOR For 604, (41TE) (41AE) * Removes retainiing ring [Use with T-1431 and center bolt from T-1437]
Also: (42LE)
T-1435
T-0
TRANSFER SHAFT BEARING SNAP-RING REMOVER-INSTALLER
T-1445 T-1435-A
TRANS SHAFT BEARING SNAP RING REMOVER-INSTALLER For: 604 Also: (Toyota 140, 150, 540) TRANSFER AND OUTPUT GEAR BEARING RACE CUP REMOVER
93

CHRYSLER
604, 604-E (40TE) (41TE) (41AE), 607 T-1446

OUTPUT AND TRANSFER GEAR HOLDER
T-1455
DIFFERENTIAL ASSEMBLY BEARING REMOVER For: 604, 604-E * Heavy duty all bronze jaws * No chisels or cut off wheels needed. * Wont damage bearing mount area.
T-1447
DIFFERENTIAL BEARING REMOVER * Used on front hub & bearing assemblies in FWD vehicles to 94 [Use with T-1432 to remove differential bearing from (41TE) ] 94 - up
T-1447
T-1456
CLUTCH SPRING COMPRESSOR ADAPTOR For: 604, 604-E [Use with T-0158]
PHOTO NOT AVAILABLE
T-1448
SEAL AND CUP INSTALLER For 604, (40TE) (41TE) (41AE) * Installs differential, extension housing oil seals & differential bearing cups. Also: (31TH)
T-3201
INNER DIFFERENTIAL ADJUSTMENT WRENCH
Also: 606
T-1449
FRONT PUMP OIL SEAL REMOVER For: (41TE) * Removes front camshaft seal in 3.0 Liter OHC V-6 engines
Also (42LE), (30RH), (32RH)
T-3202
SPLINED SOCKET WRENCH
Also; 606 (42LE)
T-3208
UNIVERSAL DRIVE HANDLE [Use with T-1452]
T-1451
BEARING CUP REMOVER For 604, (40TE) (41TE) (41AE) * Removes transfer shaft & differential bearing cups.
T-3229
FRONT PUMP OIL SEAL INSTALLER For: 604 Torqueflite & Loadflite * Use on LH vehicles
Also: (42LE)
T-0
T-1452
BEARING AND SEAL INSTALLER For (41AE) * Use on rear wheel blue hub seal. [Use with T-3208 to install differential bearing.]
T-3232
OUTPUT & TRANSFER SHAFT GEAR HOLDER During removal & installation process
T-1453
BEARING CUP AND CONE REMOVER INSTALLER KIT * New bronze collet
T-3234
OIL PUMP HOUSING SEAL INSTALLER For: (41TE) all wheel drive mini vans
94

CHRYSLER
T-1431
OVERDRIVE AND REVERSE REACTION PLATE SPRING COMPRESSOR (42LE) [Use with T-1437 center bolt and T-1443]
Also: 604 (41TE) (41AE)
606 (42LE) T-3202

SPLINED SOCKET WRENCH
Also: 604
T-3203
DIFFERENTIAL BEARING PRELOAD WRENCH
T-1432
BEARING CONE PULLER SET For (42LE) * Removes rear carrier, output gear, and transfer gear bearing cones. [Use with T-3208]
Also: (31TH), 604 (41TE) (41AE)
T-3204
T-1437
2-4 PISTON SPRING COMPRESSOR (42LE) * Center bolt to be used with T-1431 and T-1443
Also: 604, (41TE) (41AE)
MAIN & TRANSFER SHAFT RETAINING NUT WRENCH * For removing and installing [Use with T-3202]
T-3205
TRANSFER SHAFT FRONT BEARING CUP INSTALLER
T-1443
OVERDRIVE AND REVERSE SPRING COMPRESSOR (42LE) * Removes retaining ring [Use with T-1431 and center bolt from T-1437. Also: 604, (41TE) (41AE)
T-3206
TRANSFER SHAFT FRONT BEARING CUP REMOVER [Use with T-3208]
T-3207
TRANSFER SHAFT REAR BEARING CUP REMOVER
T-1449
FRONT PUMP OIL SEAL REMOVER (42LE) * Removes front camshaft seal in 3.0 Liter OHC V-6 engines
T-3208
UNIVERSAL DRIVE HANDLE [Use with T-3206 and T-1419]
T-0
Also: (41TE), (30RH) (32RH) (36RH)
T-3200
DIFFERENTIAL TURNING FORK WRENCH
T-3209
TRANSFER SHAFT SEAL REMOVER KIT For (42LE)
T-3201
INNER DIFFERENTIAL ADJUSTMENT WRENCH
Also: 604
T-3211
COLLET SET For (42LE) * Removes the output shaft bearing cone on the rear carrier 93 to current. [Use with T-1432]
95

CHRYSLER
606 (42LE) T-3213

MAIN & TRANSFER SHAFT SPROCKET REMOVER INSTALLER For (42LE) * Removes as a single unit 93 to current.
T-3222
OUTPUT SHAFT RETAINING NUT STAKING TOOL For (42LE) * 93 to current * Use after installation on LH vehicles. [Use with arbor press]
T-3214
DIFFERENTIAL INNER & OUTER ADJUSTER SEAL INSTALLER For (42LE) * Install the inner and outer adjuster seals 93-current
T-3223
LONG STUB SHAFT REMOVER For (42LE) * 93 to current [Use with T-0154- HD]
T-3215
TRANSFER SHAFT REAR & BAFFLE BEARING CUP INSTALLER For (42LE) [Use with an arbor press]
T-3224
STUB SHAFT OIL SEAL PROTECTOR For (42LE) 93 to current
T-1437 T-3216
T-3225
TRANSFER SHAFT SEAL INSTALLER For (42LE) * 93 to current
TRANSFER SHAFT RETAINING NUT STAKING TOOL For (42LE) * Use during assembly [Use with an arbor press]
T-3226
OUTPUT SHAFT REAR BEARING CONE SUPPORT PLATE For (42LE) * 93 to current * Use during installation * Also use to install ball bearing on stub shaft.
T-3218
TRANSFER SHAFT OIL SEAL PROTECTOR For (42LE) * 93 to current
T-3218 T-3219
T-3229
FRONT PUMP OIL SEAL INSTALLER For (42LE) * Use on LH vehicles. Also: 604 torqueflite & Loadflite
TRANSFER SHAFT HOLDING FIXTURE For (42LE) * Use during installation of transfer shaft seal, rear transfer shaft bearing cup and bearing cone. * 93 to current
T-3230
CARRIER BEARING INSTALLER For (42LE) * Also use to install the differential side carrier bearing in cars with 8 1/4 rear axles. [Use T-3208]
T-3220
OUTPUT SHAFT FRONT BEARING CUP REMOVER For (42LE) * 93 - current
T-3235
TRANSFER DRIVEN BEARING GEAR INSTALLER For Colt & Summit
T-3221
OUTPUT SHAFT REAR BEARING CUP REMOVER For (42LE) * 93 to current
T-3235
96

CHRYSLER
T-0030-A
UNIVERSAL H GAUGE FRONT PUMP CLEARANCE GAUGE
727 (36RH) (37RH) T-1031- A

SHIFT SELECTOR SHAFT SEAL REMOVER INSTALLER *No draining of trans fluid.
T-0033
UNIVERSAL PUMP REMOVER * Removes conventional pumps without damage.
T-1317
AIR TEST PLATE
Also: 500, 904
T-0033-A
T-1319
TRANS BAND ADAPTER 727 (36RH) * Use with torque wrench to adjust transmission bands
T-0085
T-1320
FRONT PUMP SEAL INSTALLER For (36RH) [Use with T-3208]
T-0099
T-1441
RETAINING CLIP INSTALLER REMOVER For 727 (36RH) * Used to compress front clutch assembly.
T-0133
T-1449
FRONT PUMP OIL SEAL REMOVER (36RH) * Front camshaft seal in 3.0 liter OHC V-6 engines.
T-0158- HD
CLUTCH DRUM SPRING COMPRESSOR * Long legs for lock ups * Mounts directly on work bench or vise
Also: 904 series
T-1450
REAR EXTENSION HOUSING SEAL INSTALLER For (36RH) [Use with T-3208]
T-0
T-0161- A
T-3208
UNIVERSAL DRIVE HANDLE [Use with T-1450, T-1320]
T-0166
LINE A PUMP KIT
T-0220-20
COMPLETE BUSHING DRIVER KIT
97

CHRYSLER
904 (30RH), 998 (31RH), 999 (32RH) T-0030- A

T-0158- HD
CLUTCH DRUM SPRING COMPRESSOR * Most economical unit * Long legs for lock ups * Mounts directly on work bench or vise.
Also: 727 series
T-0033
UNIVERSAL PUMP REMOVER * Removes conventional type pumps without damage.
T-0160- A
EXTENSION HOUSING BUSHING REMOVER INSTALLER AND OUTPUT SHAFT SUPPORT FIXTURE * Speeds up process
T-0033- A
T-0163- A
VACUUM PUMP HEAVY DUTY
T-0099
T-0163- C T-0130
BOOT TYPE EXTENSION SEAL INSTALLER PRESSURE GAUGE 0 - 100 pounds
T-0163- D
PRESSURE GAUGE 0 - 300 pounds
T-0154- HD
T-0166
LINE A PUMP KIT
T-0156- A
T-0156- AF
ABOVE WITHOUT BASE
98

CHRYSLER
904 (30RH), 998 (31RH), 999 (32RH) T-1031- A T-1441

SHIFT SELECTOR SHAFT SEAL REMOVER AND INSTALLER Does not require draining transmission fluid. RETAINING CLIP INSTALLER AND REMOVER For (32RH) * Used to compress front clutch assembly
Also: (42RE) (44RE) (46RE) (47RE), 727 (36RH)
T-1317
AIR TEST PLATE
T-1449
FRONT PUMP OIL SEAL REMOVER For (30RH) (32RH) * Removes front camshaft seal in 3.0 liter OHC V-6 engines.
T-0
Also: 500, 727
Also: (41TE), (42LE), (36RH)
T-1319
TRANS BAND ADAPTER For 904 (30RH) (32RH) * Use with torque wrench to adjust transmission bands
Also: (42RE) (44RE) (46RE) (47RE) (46RH), 727 (36RH)
T-1450
REAR EXTENSION HOUSING SEAL INSTALLER For 904 (32RH) [Use with T-3208]
Also: (42RE) (44RE) (46RE) (47RE), (36RH)
T-3208
UNIVERSAL DRIVE HANDLE [Use with T-1450]
T-3229
FRONT PUMP OIL SEAL INSTALLER For (30RH)
Also: (42RE) (44RE), 604 (41TE), (42LE)
99
MITSUBISHI OLD TO NEW TRANSMISSION CONVERSIONS

KM171-5 ..................F3A21-2 KM172-5 ..................F3A22-A KM175-5................ ..F4A22-2 KM176-5 ..................F4A21-2 KM177-8 ..................F4A23-2 (92-AWD) ................W4A32-1 (w/14Bolt Pan) ........F4A33-1
SPECIFIC TOOLS TOYOTA T-1435-A
TRANS SHAFT BEARING SNAP RING REMOVER-INSTALLER For: 140, 150, 540 Also: (Chrysler 604)
T-2147
TOYOTA AIR TEST PLATE
T-2162
HYUNDAI Scoupe/Accent ........A4A-F1
TOYOTA FRONT PUMP ALIGNMENT BAND
T-2195
TOYOTA GOVERNOR BORE CASE SLEEVING TOOL KIT [Use withT-2195-SL]
T-2195- SL
TOYOTA GOVERNOR BORE CASE SLEEVING TOOL BUSHING REPLACEMENT [Use with T-2195]
MITSUBISHI / HYUNDAI T-2145

MITSUBISHI-HYUNDAI END CLUTCH PISTON INSTALLER
VOLKSWAGEN T-3550
VW PINION SHAFT RETAINER WRENCH
MERCEDES T-2146
MERCEDES LINKAGE GROMMET
RENAULT
MISC TRANSMISSION TOOLS-EQUIP
MB1/MJ3 T-5299
RENAULT CLUTCH DRUM TOOL
VOLVO
AW55, AW70, AW71
T-0159- A
VOLVO EXTENSION HOUSING BUSHING REMOVER AND INSTALLER
* Opens and closes tangs on overdrive clutch unit. * Pays for itself with one use. * Fits 79 and later E-1 and E-2 models
100

Att Trans Tools

Uploaded by

Copyright:

Available Formats

Att Trans Tools

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Att Trans Tools

Uploaded by

Copyright:

Available Formats

Since 1978 ATEC Trans-Tool has maintained a reputation for manufacturing and suppling the most complete line

of specialty tools and equipment for the transmission industry.

TRANSMISSION GENERAL TOOLS & EQUIPMENT

f. Specialty Tools & Equipment ..........................................36-38

MASTER BUSHING DRIVER KIT

Contact Your Local Distributor or Mobile Tool Truck Dealer

PH: 1-800-531-5978 24 Hr. FAX 210-225-2114 www.atec-trans-tool.com

TRANSMISSION TOOLS & EQUIPMENT

Case Sleeving Tool Kits

T-1695 T-0 T-1695-SL

T-2495-SL Bushing Replacement For T-2495 T-0 T-2795

Contact Your Local Distributor or Tool Truck Dealer

PH: 1-800-531-5978 24 Hr. FAX 210-225-2114 www.atec-trans-tool.com

TRANSMISSION TOOLS & EQUIPMENT

Bushing Driver Kits BUSHING DRIVER KIT T-0220-20

MASTER BUSHING DRIVER KIT- 39 PC T-0220-39

For threaded bushing drivers

Contact Your Local Distributor or Mobile Tool Truck Dealer

PH: 1-800-531-5978 24 Hr. FAX 210-225-2114 www.atec-trans-tool.com

TRANSMISSION TOOLS & EQUIPMENT

Bushing Driver Kits T-0220-AOD

For Ford AOD

For GM 250, 250C, 350, 350C

Fits metric bushing in GM 440T4

Contact Your Local Distributor or Tool Truck Dealer

PH: 1-800-531-5978 24 Hr. FAX 210-225-2114 www.atec-trans-tool.com

TRANSMISSION TOOLS & EQUIPMENT

Transmission Support & Holding Fixtures TRANSMISSION T-0156-A GENERAL SERVICE

SUPPORT AND HOLDING FIXTURES ON PAGES 17 GM TRANSMISSION HOLDING FIXTURE

For GM 125/125C GM 440-T4

Without Base (Same features as above)

GM TRANSMISSION HOLDING FIXTURE

For GM 4T40-E * Bench mounts

FORD TRANSMISSION HOLDING FIXTURE

For Ford Transaxles

FORD TRANSMISSION HOLDING FIXTURE

For Ford E40D

Contact Your Local Distributor or Mobile Tool Truck Dealer

PH: 1-800-531-5978 24 Hr. FAX 210-225-2114 www.atec-trans-tool.com

TRANSMISSION TOOLS & EQUIPMENT

Air Test Plates

Applications ..........................Page ..............Part Number

Toyota 130 ................100............T-2147 Hyundai........................................T-5217 Suzuki ..........................................T-5117

PH: 1-800-531-5978 24 Hr. FAX 210-225-2114 www.atec-trans-tool.com

TRANSMISSION TOOLS & EQUIPMENT

Clutch Spring Compressors T-0158- SPA

[Order adapter T-1456 for use on Chrysler 604]

Contact Your Local Distributor or Mobile Tool Truck Dealer

PH: 1-800-531-5978 24 Hr. FAX 210-225-2114 www.atec-trans-tool.com

TRANSMISSION TOOLS & EQUIPMENT

Specialty Tools And Equipment T-0004

UNIVERSAL LIP SEAL INSTALLER

GET ORGANIZED * Made of oil resistant plastic * 13.5 x 18 * 15 compartments

Contact Your Local Distributor or Tool Truck Dealer

PH: 1-800-531-5978 24 Hr. FAX 210-225-2114 www.atec-trans-tool.com

TRANSMISSION TOOLS & EQUIPMENT

Specialty Tools And Equipment T-1090- HD T-0170- M

REPLACEMENT FILTER (For T-1090-HD...above)

TRANSMISSION GEN. TOOLS-EQUIP

Contact Your Local Distributor or Mobile Tool Truck Dealer