eSH Technical Catalog PDF

50 Hz
e-SH Series
CENTRIFUGAL ELECTRIC PUMPS ACCORDING TO EN 733
MADE IN AISI 316 STAINLESS STEEL AND EQUIPPED WITH IE3 MOTORS
ErP 2009/125/EC
Cod. 191002961 Rev. A Ed.01/2015

XylectTM
XylectTM is a pump solution software with an extensive online database of product information across the entire
range of pumps and related products, with multiple search options and helpful project management facilities.
The system holds up-to-date product information on thousands of products and accessories.
XylectTM can be available:
On the website www.xylect.com On Mobile Apps
For more information, please, see page 114-115.
Ecodesign Directive (ErP)

Over last decade the European Commission with the Energy Efficiency Plan pushed the European Parliament
and the Council to adopt specific measures to the purpose of reducing energy consumption and further negative
environmental impacts.
Through the Directives 2005/32/EC, energy-using products (EuP), and 2009/125/EC, energy-related products
(ErP) a framework for ecodesign requirements was established.
The Commission Regulations (EC) No 640/2009 and (EU) No 4/2014 have implemented two directives with re-
gard to ecodesign requirements for three-phase 50 Hz electric motors placed on the market and put into
service inside EU zone as self-alone units or integrated in other products.
This regulation states that motors must have efficiency level IE3 (or IE2 + Variable Speed Drive) from
1st January 2015 for 7,5 to 375 kW rated powers and from 1st January 2017 for 0,75 to 375 kW ones.
The Commission Regulation (EU) No 547/2012 has implemented two directives with regard to ecodesign requi-
rements for some types of clean water pumps placed on the market and put into service inside EU zone as
self-alone units or integrated in other products.
This regulation states that water pumps shall have index MEI 0.4 as minimum from 1st January 2015.
That index comes from a dedicated formula which considers hydraulic efficiency values at best efficiency point
(BEP), 75 % of the flow at BEP (Part load PL) and 110 % of the flow at BEP (Over load OL).
The e-SH series, for the models in the scope of the regulations above, is ErP com-pliant,
having an index MEI equal or higher than 0,4 and IE3 motor efficiency.
HYDROVAR, Xylect are trademarks or registered trademarks of Xylem Inc. or one of its subsidiaries. All
other trademarks or registered trademarks are property of their respective owners
2
CONTENTS
5
General Introduction ........................................................................................................................
6
Applications .......................................................................................................................................
8
Identification code .............................................................................................................................
9
Rating plate .......................................................................................................................................
List of Models at 50 Hz, 2 poles ................................................................................................... 10

List of Models at 50 Hz, 4 poles ................................................................................................... 11
Pump cross-section and main components ................................................................................. 12
17
Mechanical seals ..........................................................................................................................
Motors (ErP 2009/125/EC) ............................................................................................................ 18

Pumps (ErP 2009/125/EC) ............................................................................................................ 26
Minimum efficiency index (MEI) ................................................................................................... 27
Hydraulic performance range at 50 Hz, 2 poles ............................................................................ 28
Table of hydraulic performances at 50 Hz, 2 poles ........................................................................ 29
Hydraulic performance range at 50 Hz, 4 poles ............................................................................ 31
Table of hydraulic performances at 50 Hz, 4 poles ........................................................................ 32
Operating characteristics at 50 Hz, 2 poles ................................................................................... 35
Operating characteristics at 50 Hz, 4 poles ................................................................................... 57
Dimensions and weights .............................................................................................................. 79
ESH..H (ESH with Hydrovar) ...................................................................................................... 96
99
Accessories ..................................................................................................................................
Report and declarations ......................................................................................................... 104

Technical appendix ................................................................................................................. 107
3
e-SH SERIES
HYDRAULIC PERFORMANCE RANGE AT 50 Hz
ESH (2900 rpm)
ESH (1450 rpm)
4
e-SH SERIES
GENERAL INTRODUCTION
The new and improved e-SH Series is a high performance stainless steel centrifugal end-suction electro-pump
with single stage, axial flanged suction port, radial flanged discharge, and horizontal shaft.
The e-SH is fully made in AISI 316 stainless steel which makes it suitable for handling water as well as non-
aggressive or moderately aggressive fluids.
The pumps are equipped with intercheangeable mechanical seals, IE3 efficiency motors, and have a back pull-out
design (impeller, bracket and motor can be extracted without disconnecting the pump body from the piping).
The e-SH series pumps are available in the following constructions:
Extended shaft Stub shaft

Close-coupled by means of an adaptor Rigid-coupled with a bracket, an adap-
bracket with an impeller keyed directly tor and a rigid coupling keyed to the
to the special motor shaft extension. standard motor shaft extension.
Frame mounted Bare shaft pump

Flexible-coupled with bracket, support, Version without driver suitable to
flexing coupling (special version with be coupled with a standard electric
spacer on demand), aligning and an- motor.
choring base.
Hydraulic specifications Motor specifications

Maximum delivery: up to 240 m3/h for 2 poles range. Squirrel cage in short circuit enclosed construction
up to 130 m3/h for 4 poles range. with external ventilation (TEFC).
Maximum head: up to 110 m for 2 poles range. 2-pole and 4-pole ranges.
up to 23 m for 4 poles range. IP55 protection degree as motor (EN 60034-5), IPX5
Hydraulic performance compliant with as electro-pump (EN 60529).
ISO 9906:2012 Grade 3B. Performances according to EN 60034-1.
Fluid temperature range: IE3 efficiency level (three-phase 0,75 to 75 kW).
standard version (with gaskets in FPM*) 155 (F) insulation class.
-10 to +120 C Standard voltage:
versions on request (with gaskets in EPDM) 1 x 220-240 V 50 Hz for power up to 2,2 kW
-30 to +120 C. 3 x 220-240/380-415 V 50 Hz for power up to 3 kW
Maximum operating pressure: 3 x 380-415/660-690 V 50 Hz for power above 3 kW
12 bar @ 50 C and 10 bar @ 120 C Maximum ambient temperature: 40 C.
* Fluoro-elastomer: FPM (old ISO), FKM (ASTM & new ISO). Note
Anti-clockwise rotation when facing pumps suction port.
Pump does not include counter-flanges.
List of the Directives and the main technical norms

- Machinery Directive MD 2006/42/EC EN 809, EN 60204-1 (safety)
- Connection dimensions according to EN 733 EN 1092-2 (flanges)
(except for ESH 25 models)
- Electromagnetic Compatibility Directive EMCD 2004/108/EC EN 61000-6-1, EN 61000-6-3
- Ecodesign requirements for energy-related products EN 60034-30:2009, IEC 60034-30:2014

ErP 2009/125/EC, Regulation (EC) No 640/2009, Regulation (electric motors)
(EU) No 4/2014, Regulation (EU) No 547/2012
5
e-SH SERIES
COMMERCIAL BUILDING SERVICES (CBS)
APPLICATIONS & BENEFITS
Applications
The e-SH Series is suitable for many different applications demanding reliable and efficient products that require
constant or variable duty points in cost saving operation.
The e-SH Series can be used for the following CBS

applications:
HVAC
- Liquid transfer in heating and air-conditioning
systems.
- Liquid transfer in ventilation systems.
- Liquid transfer with mildly aggressive liquids or
environment.
Water Supply
- Pressure boosting in commercial buildings.
- Irrigation systems.
- Water transfer for green houses.
Diverse OEM applications
Benefits
The e-SH Series permit to achieve the following benefits.
Performances: the e-SH pumps are ErP 2015 compliant, equipped with IE3 motors and provide improved
performance vs. the current SH series of pumps. Its AISI 316 material configuration makes it ideal for pumping
mildly aggressive liquids or pumping in aggressive environment. With a standard version designed for up to PN12
pressure rating, 120 C maximum fluid temperature, and FPM elastomer, and easy maintenance, the e-SH provides
the solution to many CBS needs.
Reliability: the high quality in production, the robust construction and operation, the easily interchangeable
mechanical seals, and wear rings guarantee a continuous operation without faults and a shorter down time for
maintenance.
Total cost ownership: the best hydraulic and electric efficiency, the HYDROVAR -equipped versions, the easy
and quick maintenance, permit to reduce the operation and maintenance cost and to save energy when the pump
is working.
Pre-post sales support: we are continuously working close to our customers to help them in selecting the
right pump for the specific application. An improved user-friendly selection software improved with many selection
tools is available on the website, on DVD or on Apps for mobile phones. Experienced engineers are fully dedicated
to big projects for Municipality.
Features
Sizes DN25 to DN80.

Wide performance range up to 110 m head and 240 m/h flow.
Nominal pressure of 12 bar.
Wide range of temperatures for pumped liquids: -30C to +120C.
Wide range of materials for many different kinds of pumped liquid.
Wide range of voltages.
High performance IE3 motors.
Variable speed by optional HYDROVAR drive.
Wear rings in AISI 316L stainless steel on the front and rear shim washers of the impeller.
6
e-SH SERIES
for INDUSTRY
APPLICATIONS & BENEFITS
Applications
The e-SH Series is suitable for many different applications demanding reliable and efficient products. The
reliability, robustness, and AISI 316 material configuration of the e-SH series makes it ideal for use in aggressive envi-
ronments or for pumping of mildly aggressive fluids. Finally
the e-SH series compactness and reliability allows for use in
diverse OEM applications.
The e-SH Series can be used for the following

Industry applications:
Process
- Process cooling and Process heating
- Heat recovery
Water Supply
- Pressure boosting
- Irrigation systems
- Water transfer for green houses
- Liquid transfer with mildly aggressive liquids or
environment.
Water treatment
- Washing and cleaning
- Water treatment.
Diverse OEM applications
Benefits
The e-SH Series permit to achieve the following
benefits:
Performances: the e-SH pumps are ErP 2015

compliant, equipped with IE3 motors and provide
improved performance vs. the current SH series of pumps. Its AISI 316 material configuration makes it ideal for
pumping mildly aggressive liquids or pumping in aggressive environment. With a standard version designed for
up to PN12 pressure rating, 120 C maximum fluid temperature, an FPM elastomer, and with easy maintenance,
the e-SH provides the solution to many Industry needs.
Reliability: the high quality in production, the robust construction and operation, the easily interchangeable
mechanical seals, and wear rings guarantee a continuous operation without faults and a shorter down time for
maintenance.
Know How: the perfect configuration for an application can be made with the selection tool or with the sup-
port of our industrial experienced employees.
Pre- and post-sales support: we are continuously working close to our customers to help them in selecting
the right pump for the specific application. An improved user-friendly selection software improved with many
selection tools is available on the website, on DVD or on Apps for mobile phones. Experienced engineers are
fully dedicated to big projects for Municipality.
Features
Sizes DN25 to DN80.

Wide performance range up to 110 m head and 240 m/h flow.
Nominal pressure 12 bar.
Wide range of temperatures for pumped liquids: -30C to +120C.
Wide range of materials for many different kinds of pumped liquid.
Wide range of voltages.
High performance IE3 motors.
Variable speed by optional HYDROVAR drive.
Wear rings in AISI 316L stainless steel on the front and rear shim washers of the impeller.
7
ESH SERIES
IDENTIFICATION CODE
E S H F 6 5 - 1 6 0 / 1 1 0 A / P 2 5 V S N A
Motor power [2 to 3 digits]

kW x 10
or
D + actual impeller
diameter (mm)
Pump Type [3 digits] (bare shaft version)
[ESH] = series name
Mech Seal + Oring Config
Special trimmed Impeller
[1 digit]
[1 digit]
[A] = Ceramic/Carbon/FPM
[A] = Trimmed diameter
Coupling [1 digit] [B] = Ceramic/Carbon/EPDM
that doesnt maximi-
[ ] = bare shaft [2] = SiC/Carbon/FPM
ze motor power
[E]= extended shaft [4] = SiC/Carbon/EPDM
[X] = Trimmed diameter
[S] = stub shaft [W] = SiC/SiC/FPM
to meet customer
[F] = frame mounted [Z] = SiC/SiC/EPDM
required duty point
[C] = spacer coupling [X] = other configurations
frame mounted Motor type [2 digits]
[/P] = PLM
[/S] = SM
[/W] = Weg Impeller Material [1 digit]
[/X] = Other [S] = Fabricated Stainless
Motor operation [1 digit] Steel (1.4404)
[ ] = standard asynchronous motor [N] = Cast Stainless Steel
N poles [1 digit] (1.4408)
[H] = equipped with Hydrovar
[2] = 2 poles
[X] = other drives
[4] = 4 poles
Size of the pump [6 digits] Electrical Voltage + Casing Material [1 digit]

Discharge diameter - nominal impeller diameter Frequency [2digits] [S] = Fabricated Stainless
e.g. 32-160, 65-160 50 Hz Steel (1.4404)
5H = 1x220-240 V
5R = 3x220-240/380-415 V
5V = 3x380-415/660-690 V
5P = 3x200-208/346-360 V
5S = 3x255-265/440-460 V
5T = 3x290-300/500-525 V
5W = 3x440-460/- V
60 Hz
6F = 1x220-230 V
6E = 1x200-210 V
6P = 3x220-230/380-400 V
6R = 3x255-277/440-480 V
6V = 3x440-480/- V
6U = 3x380-400/660-690 V
6N = 3x200-208/346-360 V
6T = 3x330-346/575-600 V
EXAMPLES
ESHS 80-200/300/W25VSNA
End-suction, electric pump with stub shaft coupling, DN 80 nominal discharge port, 200 mm nominal impeller diameter, 30 kW rated motor power,
WEG IE3 model, 2-pole, 50 Hz 380-415/660-690 V, fabricated stainless steel casing, cast stainless steel impeller, Ceramic/Carbon/FPM mechanical
seal.
ESHF 80-160/22A/P45RSNA
End-suction, electric pump with frame mounted coupling, DN 80 nominal discharge port, 160 mm nominal impeller diameter, 2,2 kW rated motor
power, trimmed impeller, PLM IE3 model, 4-pole, 50 Hz 220-240/380-415 V, fabricated stainless steel casing, cast stainless steel impeller, Ceramic/
Carbon/FPM mechanical seal.
ESH 50-250/D224SSA
End-suction, bare shaft pump, DN 50 nominal discharge port, 250 mm nominal impeller diameter, 224 mm actual impeller diameter, fabricated
stainless steel casing, fabricated stainless steel impeller, Ceramic/Carbon/FPM mechanical seal.
8
ESH SERIES
RATING PLATE
ESHE, ESHS (ELECTRIC PUMP)

1 13 9 10 12 11 7 2 19
TYPE No/Date
PN kPa tmax C tmin C Code Kg
F mm Q m/h H m n 1/min P2 kW F MEI T p%
T mm
REGULATION (EU) No 547/2012
3 4 6 5 15 14
ESHF (ELECTRIC PUMP) ESH (PUMP ONLY)
1 13 12 10 9 2 7 8 1 13 12 10 9 2 7 8
REGULATION (EU) No 547/2012 REGULATION (EU) No 547/2012
11 19 3 4 6 5 15 14 11 19 3 4 6 5 15 14
LEGEND
1 - Pump / Electric pump unit type 10 - Trimmed impeller diameter (only filled-in for
2 - Pump / Electric pump unit code models with trimmed impellers)
3 - Flow range 11 - Minimum operating liquid temperature
4 - Head range 12 - Maximum operating liquid temperature
5 - Nominal or maximum pump power 13 - Maximum operating pressure
6 - Speed 14 - Hydraulic efficiency in best efficiency point
7 - Serial number or order number 15 - Minimum efficiency index MEI (Regulation (EU)
8 - Order position number No 547/2012)
9 - Full impeller diameter (only filled in for trimmed 19 - Weight
impellers)
9
ESH SERIES
ESH SERIES
LIST OF
LIST OFMODELS
MODELSAT AT
50 Hz,
50 2Hz,
POLES
2 POLES
SIZE kW VERSION SIZE kW VERSION
ESH..2 ESHE..M ESHE ESHS ESHF ESHC ESH..2 ESHE..M ESHE ESHS ESHF ESHC
25-125/07 0,75 - 65-160/40 4 -
25-125/11 1,1 - 65-160/55 5,5 -
25-160/15 1,5 - 65-160/75 7,5 -
25-160/22 2,2 - 65-160/92 9,2 - - - -
25-200/30 3 - - 65-160/110A 11 - -
25-200/40 4 - - 65-160/110 11 -
25-250/55 5,5 - - 65-200/150 15 -
25-250/75 7,5 - - 65-200/185 18,5 -
25-250/110 11 - - 65-200/220 22 -
32-125/07 0,75 65-250/300 30 - -
32-125/11 1,1 65-250/370 37 - -
32-160/15 1,5 80-160/110 11 -
32-160/22 2,2 80-160/150 15 -
32-200/30 3 - 80-160/185 18,5 -
32-200/40 4 - 80-200/220 22 -
32-250/55 5,5 - 80-200/300 30 - -
32-250/75 7,5 - 80-200/370 37 - -
32-250/110 11 - 80-250/450 45 - - -
40-125/11 1,1 80-250/550 55 - - -
40-125/15 1,5 80-250/750 75 - - -
40-125/22 2,2
40-160/30 3 -
40-160/40 4 -
40-200/55 5,5 -
40-200/75 7,5 -
40-250/92 9,2 - - - -
40-250/110A 11 - -
40-250/110 11 -
40-250/150 15 -
50-125/22 2,2
50-125/30 3 -
50-125/40 4 -
50-160/55 5,5 -
50-160/75 7,5 -
50-200/92 9,2 - - - -
50-200/110A 11 - -
50-200/110 11 -
50-250/150 15 -
50-250/185 18,5 -
50-250/220 22 -
= Available ESH_models-2p50-en_a_sc
LEGEND
ESHE..M : Close-coupled version with single-phase motor.

ESHE : Close-coupled version.
ESHS : Close-coupled version with rigid coupling and standardised motor.
ESHF : Version with elastic coupling, support, base and standardised motor.
ESHC : Version with elastic coupling and spacer, support, base and standardised motor.
10
ESH SERIES
ESH SERIES
LIST OF
LIST OFMODELS
MODELSATAT
50 50
Hz, Hz,
4 POLES
4 POLES
SIZE kW VERSION SIZE kW VERSION
ESH..4 ESHE ESHS ESHF ESHC ESH..4 ESHE ESHS ESHF ESHC
25-125/02A 0,25 - - 65-200/15 1,5 -
25-125/02 0,25 - - 65-200/22 2,2 -
25-160/02A 0,25 - - 65-200/30 3 -
25-160/02 0,25 - - 65-250/40 4 -
25-200/03 0,37 - - 65-250/55 5,5 -
25-200/05 0,55 - - 80-160/15 1,5 -
25-250/07 0,75 - 80-160/22A 2,2 -
25-250/11 1,1 - 80-160/22 2,2 -
25-250/15 1,5 - 80-200/30 3 -
32-125/02A 0,25 - - 80-200/40 4 -
32-125/02 0,25 - - 80-250/55 5,5 -
32-160/02A 0,25 - - 80-250/75 7,5 -
32-160/02 0,25 - - 80-250/110 11 -
32-200/03 0,37 - -
32-200/05 0,55 - -
32-250/07 0,75 -
32-250/11 1,1 -
32-250/15 1,5 -
40-125/02A 0,25 - -
40-125/02 0,25 - -
40-160/03 0,37 - -
40-160/05 0,55 - -
40-200/07 0,75 -
40-200/11 1,1 -
40-250/11 1,1 -
40-250/15 1,5 -
40-250/22 2,2 -
50-125/02 0,25 - -
50-125/03 0,37 - -
50-125/05 0,55 - -
50-160/07 0,75 -
50-160/11 1,1 -
50-200/11 1,1 -
50-200/15 1,5 -
50-250/22A 2,2 -
50-250/22 2,2 -
50-250/30 3 -
= Available ESH_models-4p50-en_a_sc
11
DENOMINAZIONE MODELLI
ESHE SERIES SERIE SHE - SHE4 CON
ELECTRIC PUMP CROSS-SECTION AND MAIN COMPONENTS
STAFFA DI SOSTEGNO
(ESHE) VERSIONS
2 POLES 4 POLES
25-125/07 25-200/05
25-125/11 25-250/07
25-160/15 25-250/11
25-160/22 25-250/15
25-200/30 32-200/05
25-200/40 32-250/07
25-250/55 32-250/11
25-250/75 32-250/15
25-250/110 40-160/05
32-125/07 40-200/07
32-125/11 40-200/11
32-160/15 40-250/11
32-160/22 40-250/15
32-200/30 40-250/22
32-200/40 50-125/05
32-250/55 50-160/07
32-250/75 50-160/11
32-250/110 50-200/11
40-125/11 50-200/15
40-125/15 50-250/22A
40-125/22 50-250/22
40-160/30 50-250/30
40-160/40 65-200/15
40-200/55 65-200/22
40-200/75 65-200/30
40-250/92 65-250/40
40-250/110 65-250/55
50-125/22 80-160/15
50-125/30 80-160/22A
50-125/40 80-160/22
50-160/55 80-200/30
50-160/75 80-200/40
50-200/92 80-250/55
50-200/110 80-250/75
65-160/40
65-160/55
65-160/75
65-160/92
65-160/110
80-160/110
MATERIALI ESHE ESHE-p-en_a_mo
REF. NAME MATERIAL REFERENCE STANDARDS

N. EUROPE USA
1 Pump body Stainless steel EN 10088-1-X2CrNiMo17-12-2 (1.4404) AISI 316L
Impeller 25-32-40-50-65(160 )** Stainless steel EN 10088-1-X2CrNiMo17-12-2 (1.4404) AISI 316L
2
Impeller 65(160)***, 65(200-250)-80 Stainless steel EN 10213-4-GX5CrNiMo19-11-2 (1.4408) ASTM CF8M (cast AISI 316)
3 Seal housing Stainless steel EN 10088-1-X2CrNiMo17-12-2 (1.4404) AISI 316L
4 Wear ring Stainless steel EN 10088-1-X2CrNiMo17-12-2 (1.4404) AISI 316L
5 Counterwear ring Stainless steel EN 10088-1-X2CrNiMo17-12-2 (1.4404) AISI 316L
6 Shaft extension Stainless steel EN 10088-1-X5CrNiMo17-12-2 (1.4401) AISI 316
7 Rigid shaft coupling Stainless steel EN 10088-1-X5CrNiMo17-12-2 (1.4401) AISI 316
8 Impeller locknut and washer Stainless steel EN 10088-1-X5CrNiMo17-12-2 (1.4401) AISI 316
9 Tab Stainless steel EN 10088-1-X2CrNiMo17-12-2 (1.4404) AISI 316L
10 Fill/drain plugs Stainless steel EN 10088-1-X5CrNiMo17-12-2 (1.4401) AISI 316
11 Mechanical seal Ceramic / Carbon / FPM (standard version)
12 Elastomers FPM (standard version)
Adapter * Aluminium EN 1706-AC-AlSi11Cu2 (Fe) (AC46100) -
13
Adapter Cast iron EN 1561-GJL-200 (JL1030) ASTM Class 25
15 Pump body fastening bolts & screws Galvanized steel
* 2/4 pole: 25/32/40-125, 25/32/40-160, 25/32/40-200 ESHE-en_a_tm
** 2 pole: 65-160/40, 65-160/55, 65-160/75

*** 2 pole: 65-160/92, 65-160/110A, 65-160/110
12
ESHE SERIES
SERIE ESHE CON PIEDE DI
SOSTEGNO SUL MOTORE
(ESHE) VERSIONS
2 POLES 4 POLES
40-250/150 80-250/110
50-250/150
50-250/185
50-250/220
65-200/150
65-200/185
65-200/220
80-160/150
80-160/185
80-200/220
ESHE-s-en_a_mo
SERIE SHE4 CON MOTORE
MEC 71 B5
(ESHE) VERSIONS
4 POLES
25-125/02A 40-125/02A
25-125/02 40-125/02
25-160/02A 40-160/03
25-160/02 50-125/02
25-200/03 50-125/03
32-125/02A
32-125/02
32-160/02A
32-160/02
32-200/03
ESHE4-p-en_a_mo
MATERIALI ESHE

N. EUROPE USA
2
13
* 2/4 pole: 25/32/40-125, 25/32/40-160, 25/32/40-200 ESHE-en_a_tm
** 2 pole: 65-160/40, 65-160/55, 65-160/75

*** 2 pole: 65-160/92, 65-160/110A, 65-160/110
13
ESHS SERIES SERIE ESHS - ESHS4 CON
STAFFA DI SOSTEGNO
(ESHS) VERSIONS
2 POLES 4 POLES
25-125/07 25-250/07
25-125/11 25-250/11
25-160/15 25-250/15
25-160/22 32-250/07
25-200/30 32-250/11
25-200/40 32-250/15
25-250/55 40-200/07
25-250/75 40-200/11
32-125/07 40-250/11
32-125/11 40-250/15
32-160/15 40-250/22
B5 32-160/22 50-160/07
32-200/30 50-160/11
32-200/40 50-200/11
32-250/55 50-200/15
32-250/75 50-250/22A
40-125/11 50-250/22
40-125/15 50-250/30
40-125/22 65-200/15
40-160/30 65-200/22
40-160/40 65-200/30
40-200/55 65-250/40
40-200/75 65-250/55
50-125/22 80-160/15
50-125/30 80-160/22A
50-125/40 80-160/22
50-160/55 80-200/30
50-160/75 80-200/40
65-160/40 80-250/55
65-160/55 80-250/75
65-160/75
MATERIALI ESHS ESHS-p-en_a_mo

N. EUROPE USA
2
9 Tab Acciaio inox EN 10088-1-X2CrNiMo17-12-2 (1.4404) AISI 316L
13
14 Adapter motor coupling Cast iron EN 1561-GJL-200 (JL1030) ASTM Class 25
* 2/4 pole: 25/32/40-125, 25/32/40-160, 25/32/40-200 ESHS-en_a_tm
** 2 pole: 65-160/40, 65-160/55, 65-160/75

*** 2 pole: 65-160/92, 65-160/110A, 65-160/110
14
ESHS SERIES
SERIE ESHS CON PIEDE DI
SOSTEGNO SUL MOTORE
(ESHS) VERSIONS
2 POLES 4 POLES
25-250/110 80-250/110
32-250/110
40-250/110A
40-250/110
B35 40-250/150
50-200/110A
50-200/110
50-250/150
50-250/185
50-250/220
65-160/110A
65-160/110
65-200/150
65-200/185
65-200/220
65-250/300
65-250/370
80-160/110
80-160/150
80-160/185
80-200/220
80-200/300
80-200/370
ESHS-s-en_a_mo
MATERIALI ESHS

N. EUROPE USA
2
9 Tab Acciaio inox EN 10088-1-X2CrNiMo17-12-2 (1.4404) AISI 316L
13
14 Adapter motor coupling Cast iron EN 1561-GJL-200 (JL1030) ASTM Class 25
* 2/4 pole: 25/32/40-125, 25/32/40-160, 25/32/40-200 ESHS-en_a_tm
** 2 pole: 65-160/40, 65-160/55, 65-160/75

*** 2 pole: 65-160/92, 65-160/110A, 65-160/110
15
ESH, ESHF, ESHC SERIES
B3 DENOMINAZIONE MODELLI
SERIE ESHF
VERSIONS
ESH, ESHF, ESHC
25-125
25-160
25-200
25-250
32-125
32-160
32-200
32-250
40-125
40-160
40-200
40-250
50-125
50-160
50-200
50-250
65-160
65-200
65-250
80-160
80-200
80-250
ESHF-p-en_a_mo
MATERIALI ESHF

N. EUROPE USA
2
13
14 Transmission support body Cast iron EN 1561-GJL-200 (JL1030) ASTM Class 25
* 2/4 pole: 25/32/40-125, 25/32/40-160, 25/32/40-200 ESHF-en_a_tm
** 2 pole: 65-160/40, 65-160/55, 65-160/75

*** 2 pole: 65-160/92, 65-160/110A, 65-160/110
16
ESH SERIES
MECHANICAL SEAL
Mechanical seal with mounting dimensions according to EN 12756 and ISO 3069.
(*) Standard version (**) Version with fixed assembly anti-rotation
TENUTA MECCANICA SH MATERIALI

LIST OF MATERIALS
POSITION 1 - 2 POSITION 3 POSITION 4 - 5
B : Resin impregnated carbon E : EPDM G : AISI 316

Q 1 : Silicon carbide V : FPM
V : Ceramic
sh_ten-mec-en_a_tm
TENUTA MECCANICA SH COMBINAZIONI

SEAL TYPES
POSITION TEMPERATURE
TYPE 1 2 3 4 5
( C )
ROTATING ASSEMBLY FIXED ASSEMBLY ELASTOMERS SPRINGS OTHER COMPONENTS
STANDARD MECHANICAL SEAL
VB V G G V B V G G -10 +120
OTHER MECHANICAL SEAL TYPES
Q1 B V G G Q1 B V G G -10 +120
Q1 Q1 V G G Q1 Q1 V G G -10 +120
VB E G G V B E G G -30 +120
Q1 B E G G Q1 B E G G -30 +120
Q1 Q1 E G G Q1 Q1 E G G -30 +120
sh_tipi-ten-mec-en_a_tc
PRESSURE / TEMPERATURE APPLICATIONS LIMITS FOR COMPLETE PUMP

(APPLICABLE WITH ANY OF THE SEALS LISTED ABOVE)
17
ErP 2009/125/EC
ESH SERIES
MOTORS
Over last decade the European Commission with the Energy Efficiency Plan pushed the European Parliament
and the Council to adopt specific measures to the purpose of reducing energy consumption and further negative
environmental impacts.
Through the Directives 2005/32/EC, energy-using products (EuP), and 2009/125/EC, energy-related products (ErP)
a framework for ecodesign requirements was established.
The Commission Regulations (EC) No 640/2009 and (EU) No 4/2014 have implemented two directives with regard
to ecodesign requirements for electric motors placed on the market and put into service inside EU zone as self-alone
units or integrated in other products.
The various types considered include three-phase 50 Hz surface motors with power outputs ranging from
0,75 to 375 kW included.
Regulations also establish the following deadlines.

from kW minimum level of efficiency (IE)
16 June 2011 0,75 375 IE2
27 July 2014 0,75 375 new exclusion criteria
< 7,5 IE2
1 January 2015 IE3
7,5 375
IE2 fitted with variable speed drive
IE3
1 January 2017 0,75 375
IE2 fitted with variable speed drive
Short-circuit squirrel-cage motor, enclosed Single-phase version:

construction with external ventilation (TEFC). 220-240 V 50 Hz
Rated power from 0,75 to 75 kW for 2-pole range Built-in automatic reset overload protection up
and from 0,25 to 11 kW for 4-pole range. to 1,5 kW. For higher powers the protection must be
IP55 protection degree. provided by the user.
Insulation class 155 (F). Three-phase version:
Standard three-phase surface motors 0,75 kW 220-240/380-415 V 50 Hz for power up to 3 kW.
supplied as IE3. 380-415/660-690 V 50 Hz for power above 3 kW.
IE efficiency level according to EN 60034-30:2009 Overload protection to be provided by the user.
and IEC 60034-30-1:2014 ( 0,75 kW). PTC included as standard only for WEG motors
Electrical performances according to EN 60034-1. (one per phase, 155C).
Metric cable gland according to EN 50262. Maximum ambient temperature: 40 C.
ESHE SERIES
MOTORI MONOFASE PER SERIE SHE 50 Hz, 2 poli
SINGLE-PHASE MOTORS AT 50 Hz, 2 POLES
INPUT CAPACITOR DATA FOR 230 V 50 Hz VOLTAGE
Construction
IEC SIZE*
Design
CURRENT
PN In (A) Tn
MOTOR TYPE
-1
kW 220-240 V F V min ls / ln % cos
Nm Ts/Tn Tm/Tn
0,75 SM90RB14S2/1075 90R B14 4,83-5,23 30 450 2875 5,28 71,8 0,92 2,49 0,70 2,59
1,1 SM90RB14S2/1115 90R B14 6,88-6,65 30 450 2800 3,89 74,7 0,96 3,75 0,46 1,72
1,5 SM90RB14S2/1155 90R B14 9,21-8,58 40 450 2810 4,00 76,1 0,98 5,15 0,39 1,74
2,2 PLM90B14S2/1225 90 B14 12,5-11,6 70 450 2825 4,47 82,4 0,97 7,43 0,53 1,87
* R = Reduced size of motor casing as compared to shaft extension and flange. ESHE-motm-2p50-en_a_te
18
ESHE SERIES
MOTORI TRIFASE PER SERIE ESHE 50 Hz, 2 poli
THREE-PHASE MOTORS AT 50 Hz, 2 POLES
Efficiency N
manufacture
%
Year of
220 V 230 V 240 V 380 V 400 V 415 V
PN Y 380 V Y 400 V Y 415 V Y 660 V Y 690 V IE
kW 4/4 3/4 2/4 4/4 3/4 2/4 4/4 3/4 2/4 4/4 3/4 2/4 4/4 3/4 2/4 4/4 3/4 2/4
0,75 82,5 83,1 81,3 82,8 82,7 80,1 82,6 82,0 78,9 82,5 82,0 78,9 82,5 82,0 78,9 82,5 82,0 78,9
1,1 84,0 84,7 83,4 84,4 84,5 82,5 84,3 84,0 81,4 84,0 84,0 81,4 84,0 84,0 81,4 84,0 84,0 81,4
1,5 85,6 86,5 85,8 85,9 86,4 84,9 86,0 86,0 84,0 85,6 86,0 84,0 85,6 86,0 84,0 85,6 86,0 84,0
2,2 86,5 87,4 86,8 86,4 86,9 85,7 86,6 86,7 85,0 86,4 86,7 85,0 86,4 86,7 85,0 86,4 86,7 85,0
from 11/2014
3 87,2 88,5 88,3 87,5 88,2 87,5 87,5 87,8 86,4 87,2 87,8 86,4 87,2 87,8 86,4 87,2 87,8 86,4
4 89,1 90,1 89,2 89,1 90,1 89,2 89,1 90,1 89,2 89,1 90,3 90,4 89,6 90,4 89,9 89,6 90,1 89,2
5,5 89,5 89,6 88,0 89,5 89,6 88,0 89,5 89,6 88,0 89,5 90,3 89,9 89,7 90,0 89,0 89,6 89,6 88,0 3
7,5 90,6 90,5 89,0 90,6 90,5 89,0 90,6 90,5 89,0 90,6 91,0 90,2 90,8 90,8 89,6 90,7 90,5 89,0
9,2 90,8 91,0 89,7 90,8 91,0 89,7 90,8 91,0 89,7 90,8 91,4 90,8 91,1 91,3 90,3 91,1 91,0 89,7
11 91,3 92,0 91,1 91,3 92,0 91,1 91,3 92,0 91,1 91,3 92,2 92,2 91,6 92,2 91,7 91,7 92,0 91,1
15 92,5 92,4 91,2 92,5 92,4 91,2 92,5 92,4 91,2 92,7 93,3 92,9 93,1 93,3 92,7 92,5 92,4 91,2
18,5 92,6 93,1 92,4 92,6 93,1 92,4 92,6 93,1 92,4 92,6 93,2 93,0 92,9 93,3 92,8 92,9 93,1 92,4
22 93,0 92,7 91,3 93,0 92,7 91,3 93,0 92,7 91,3 93,0 93,2 92,4 93,1 93,0 91,9 93,0 92,7 91,3
Manufacturer
Construction
Xylem Service Italia Srl Data for 400 V / 50 Hz Voltage

IEC SIZE*
Design
Reg. No. 07520560967

PN Montecchio Maggiore Vicenza - Italia N. of fN TN
kW Model Poles Hz cos ls / lN Nm Ts/TN Tm/Tn
0,75 SM90RB14S/307PE 90R 0,78 7,38 2,48 3,57 3,75
1,1 SM90RB14S/311PE 90R 0,79 8,31 3,63 3,95 3,95
1,5 SM90RB14S/315PE 90R 0,80 8,80 4,96 4,31 4,10
2,2 PLM90B14S2/322 E3 90 0,80 8,77 7,28 3,72 3,70
3 PLM90B14S2/330 E3 90 0,79 7,81 9,93 4,26 3,94
4 PLM112RB14S2/340 E3 112R 0,85 9,13 13,2 3,82 4,32
SPECIAL
5,5 PLM112B14S2/355 E3 112 2 50 0,85 10,5 18,1 4,74 5,11

7,5 PLM132B14S2/375 E3 132 0,85 10,2 24,4 3,43 4,76
9,2 PLM132B14S2/392 E3 132 0,85 10,1 30,0 3,73 4,81
11 PLM132B14S2/3110 E3 132 0,86 9,89 35,9 3,46 4,59
15 PLM160B34S3/3150 E3 160 0,88 9,51 48,6 2,73 4,32
18,5 PLM160B34S3/3185 E3 160 0,88 9,81 59,9 2,81 4,53
22 PLM160B34S3/3220 E3 160 0,85 10,9 71,1 3,26 5,12
Voltage UN
Operating conditions **
V
Observe the regulations and codes locally
in force regarding sorted waste disposal.
Y Y Altitude T. amb ATEX

PN 220 V 230 V 240 V 380 V 400 V 415 V 380 V 400 V 415 V 660 V 690 V nN Above Sea min/max
kW IN (A) min-1 Level (m) C
0,75 2,96 2,94 2,96 1,71 1,70 1,71 1,70 1,69 1,70 0,98 0,98 2875 2895
1,1 4,19 4,14 4,16 2,42 2,39 2,40 2,41 2,38 2,38 1,39 1,37 2870 2900
1,5 5,56 5,49 5,51 3,21 3,17 3,18 3,21 3,18 3,19 1,85 1,84 2870 2895
2,2 7,97 7,90 7,98 4,6 4,56 4,61 4,57 4,54 4,57 2,64 2,62 2880 2900
3 11,0 11,0 11,2 6,35 6,33 6,44 6,29 6,27 6,34 3,63 3,62 2865 2895
4 13,6 13,4 13,4 7,87 7,75 7,74 7,80 7,62 7,61 4,50 4,40 2885 2910
5,5 18,1 17,9 18,1 10,4 10,4 10,4 10,6 10,5 10,7 6,10 6,05 2880 2910 1000 -15 / 40 No
7,5 24,8 24,4 24,3 14,3 14,1 14,0 14,4 14,1 14,2 8,32 8,16 2920 2935
9,2 30,6 30,1 30,2 17,6 17,4 17,5 17,5 17,2 17,3 10,1 9,93 2920 2935
11 35,7 35,0 34,9 20,6 20,2 20,2 20,6 20,2 20,2 11,9 11,7 2910 2930
15 47,6 46,1 45,2 27,5 26,6 26,1 27,5 26,6 26,1 15,9 15,3 2940 2950
18,5 58,3 56,7 55,6 33,7 32,7 32,1 34,0 33,0 32,7 19,6 19,0 2940 2950
22 72,9 73,1 73,7 42,1 42,2 42,6 40,9 40,4 40,6 23,6 23,3 2950 2960
* R = Reduced size of motor casing as compared to shaft extension and flange. ESHE-IE3-mott-2p50-en_a_te
** Operating conditions to be referred to motor only. About electric pump, refer to limits in users manual.
19
ESHS SERIES
MOTORI TRIFASE PER SERIE ESHS 50 Hz, 2 poli
THREE-PHASE MOTORS AT 50 Hz, 2 POLES (up to 22 kW)
Efficiency N
manufacture
%
Year of
220 V 230 V 240 V 380 V 400 V 415 V
PN Y 380 V Y 400 V Y 415 V Y 660 V Y 690 V IE
kW 4/4 3/4 2/4 4/4 3/4 2/4 4/4 3/4 2/4 4/4 3/4 2/4 4/4 3/4 2/4 4/4 3/4 2/4
0,75 82,5 83,1 81,3 82,8 82,7 80,1 82,6 82,0 78,9 82,5 82,0 78,9 82,5 82,0 78,9 82,5 82,0 78,9
1,1 84,0 84,7 83,4 84,4 84,5 82,5 84,3 84,0 81,4 84,0 84,0 81,4 84,0 84,0 81,4 84,0 84,0 81,4
1,5 85,6 86,5 85,8 85,9 86,4 84,9 86,0 86,0 84,0 85,6 86,0 84,0 85,6 86,0 84,0 85,6 86,0 84,0
2,2 86,5 87,4 86,8 86,4 86,9 85,7 86,6 86,7 85,0 86,4 86,7 85,0 86,4 86,7 85,0 86,4 86,7 85,0
from 11/2014
3 87,2 88,5 88,3 87,5 88,2 87,5 87,5 87,8 86,4 87,2 87,8 86,4 87,2 87,8 86,4 87,2 87,8 86,4
4 89,1 90,1 89,2 89,1 90,1 89,2 89,1 90,1 89,2 89,1 90,3 90,4 89,6 90,4 89,9 89,6 90,1 89,2 3
5,5 89,5 89,6 88,0 89,5 89,6 88,0 89,5 89,6 88,0 89,5 90,3 89,9 89,7 90,0 89,0 89,6 89,6 88,0
7,5 90,6 90,5 89,0 90,6 90,5 89,0 90,6 90,5 89,0 90,6 91,0 90,2 90,8 90,8 89,6 90,7 90,5 89,0
11 91,8 92,3 91,5 91,8 92,3 91,5 91,8 92,3 91,5 91,8 92,3 91,9 92,2 92,5 91,8 92,3 92,4 91,5
15 92,5 92,4 91,2 92,5 92,4 91,2 92,5 92,4 91,2 92,7 93,3 92,9 93,1 93,3 92,7 92,5 92,4 91,2
18,5 92,6 93,1 92,4 92,6 93,1 92,4 92,6 93,1 92,4 92,6 93,2 93,0 92,9 93,3 92,8 92,9 93,1 92,4
22 93,0 92,7 91,3 93,0 92,7 91,3 93,0 92,7 91,3 93,0 93,2 92,4 93,1 93,0 91,9 93,0 92,7 91,3
Manufacturer
Construction

IEC SIZE*
Design
Reg. No. 07520560967

kW Model Poles Hz cos
ls / lN Nm Ts/TN Tm/Tn
0,75 SM80B5/307PE 80 0,78 7,38 2,48 3,57 3,75
1,1 SM80B5/311PE 80 0,79 8,31 3,63 3,95 3,95
1,5 SM90RB5/315PE 90R 0,80 8,80 4,96 4,31 4,10
2,2 PLM90B5/322 E3 90 0,80 8,77 7,28 3,72 3,70
B5
3 PLM100RB5/330 E3 100R 0,79 7,81 9,93 4,26 3,94
4 PLM112RB5/340 E3 112R 0,85 9,13 13,2 3,82 4,32
2 50
5,5 PLM132RB5/355 E3 132R 0,85 10,5 18,1 4,74 5,11
7,5 PLM132B5/375 E3 132 0,85 10,2 24,4 3,43 4,76
11 PLM160B35/3110 E3 160 0,88 8,59 35,6 2,36 4,14
15 PLM160B35/3150 E3 160 0,88 9,51 48,6 2,73 4,32
B35
18,5 PLM160B35/3185 E3 160 0,88 9,81 59,9 2,81 4,53
22 PLM180RB35/3220 E3 180R 0,85 10,9 71,1 3,26 5,12
Voltage UN
V

0,75 2,96 2,94 2,96 1,71 1,70 1,71 1,70 1,69 1,70 0,98 0,98 2875 2895
1,1 4,19 4,14 4,16 2,42 2,39 2,40 2,41 2,38 2,38 1,39 1,37 2870 2900
1,5 5,56 5,49 5,51 3,21 3,17 3,18 3,21 3,18 3,19 1,85 1,84 2870 2895
2,2 7,97 7,90 7,98 4,6 4,56 4,61 4,57 4,54 4,57 2,64 2,62 2880 2900
3 11,0 11,0 11,2 6,35 6,33 6,44 6,29 6,27 6,34 3,63 3,62 2865 2895
4 13,6 13,4 13,4 7,87 7,75 7,74 7,80 7,62 7,61 4,50 4,40 2885 2910
1000 -15 / 40 No
5,5 18,1 17,9 18,1 10,4 10,4 10,4 10,6 10,5 10,7 6,10 6,05 2880 2910
7,5 24,8 24,4 24,3 14,3 14,1 14,0 14,4 14,1 14,2 8,32 8,16 2920 2935
11 35,0 33,9 33,0 20,2 19,6 19,1 20,4 19,6 19,2 11,8 13,3 2935 2950
15 47,6 46,1 45,2 27,5 26,6 26,1 27,5 26,6 26,1 15,9 15,3 2940 2950
18,5 58,3 56,7 55,6 33,7 32,7 32,1 34,0 33,0 32,7 19,6 19,0 2940 2950
22 72,9 73,1 73,7 42,1 42,2 42,6 40,9 40,4 40,6 23,6 23,3 2950 2960
* R = Reduced size of motor casing as compared to shaft extension and flange. ESHS-IE3-mott-2p50-en_a_te
20
ESHF, ESHC SERIES
MOTORI TRIFASE PER SERIE SHF 50 Hz, 2 poli (fino a 18,5 kW)
THREE-PHASE MOTORS AT 50 Hz, 2 POLES (up to 18,5 kW)
Efficiency N
manufacture
%
Year of
220 V 230 V 240 V 380 V 400 V 415 V
PN Y 380 V Y 400 V Y 415 V Y 660 V Y 690 V IE
kW 4/4 3/4 2/4 4/4 3/4 2/4 4/4 3/4 2/4 4/4 3/4 2/4 4/4 3/4 2/4 4/4 3/4 2/4
0,75 82,5 83,1 81,3 82,8 82,7 80,1 82,6 82,0 78,9 82,5 82,0 78,9 82,5 82,0 78,9 82,5 82,0 78,9
1,1 84,0 84,7 83,4 84,4 84,5 82,5 84,3 84,0 81,4 84,0 84,0 81,4 84,0 84,0 81,4 84,0 84,0 81,4
1,5 84,6 85,8 85,4 85,5 86,3 85,2 85,9 86,2 84,8 84,6 85,8 84,8 84,6 85,8 84,8 84,6 85,8 84,8
2,2 86,5 87,4 86,8 86,4 86,9 85,7 86,6 86,7 85,0 86,4 86,7 85,0 86,4 86,7 85,0 86,4 86,7 85,0
from 11/2014
3 88,7 89,5 89,1 89,1 89,5 88,4 89,1 89,1 87,7 88,7 89,1 87,7 88,7 89,1 87,7 88,7 89,1 87,7
4 88,6 89,0 87,6 88,6 89,0 87,6 88,6 89,0 87,6 88,7 89,6 89,1 88,6 89,2 88,3 88,9 89,0 87,6 3
5,5 90,1 89,8 88,0 90,1 89,8 88,0 90,1 89,8 88,0 90,2 90,5 89,5 90,3 90,2 88,8 90,1 89,8 88,0
7,5 90,6 90,5 89,0 90,6 90,5 89,0 90,6 90,5 89,0 90,6 91,0 90,2 90,8 90,8 89,6 90,7 90,5 89,0
11 91,8 92,3 91,5 91,8 92,3 91,5 91,8 92,3 91,5 91,8 92,3 91,9 92,2 92,5 91,8 92,3 92,4 91,5
15 92,5 92,4 91,2 92,5 92,4 91,2 92,5 92,4 91,2 92,7 93,3 92,9 93,1 93,3 92,7 92,5 92,4 91,2
18,5 92,6 93,1 92,4 92,6 93,1 92,4 92,6 93,1 92,4 92,6 93,2 93,0 92,9 93,3 92,8 92,9 93,1 92,4
Manufacturer
Construction

IEC SIZE
Design
Reg. No. 07520560967

0,75 SM80B3/307PE 80 0,78 7,38 2,48 3,57 3,75
1,1 SM80B3/311PE 80 0,79 8,31 3,63 3,95 3,95
1,5 PLM90B3/315 E3 90 0,86 8,04 4,96 3,34 3,27
2,2 PLM90B3/322 E3 90 0,80 8,77 7,28 3,72 3,70
3 PLM100B3/330 E3 100 0,84 9,65 9,84 3,59 4,26
4 PLM112B3/340 E3 112 B3 2 50 0,86 9,41 13,2 3,95 4,46
5,5 PLM132B3/355 E3 132 0,83 10,0 17,9 3,33 4,65
7,5 PLM132B3/375 E3 132 0,85 10,2 24,4 3,43 4,76
11 PLM160B3/3110 E3 160 0,88 8,59 35,6 2,36 4,14
15 PLM160B3/3150 E3 160 0,88 9,51 48,6 2,73 4,32
18,5 PLM160B3/3185 E3 160 0,88 9,81 59,9 2,81 4,53
Voltage UN
V
0,75 2,96 2,94 2,96 1,71 1,70 1,71 1,70 1,69 1,70 0,98 0,98 2875 2895
1,1 4,19 4,14 4,16 2,42 2,39 2,40 2,41 2,38 2,38 1,39 1,37 2870 2900
1,5 5,35 5,11 5,04 3,09 2,95 2,91 3,09 2,96 2,91 1,78 1,71 2865 2890
2,2 7,97 7,90 7,98 4,60 4,56 4,61 4,57 4,54 4,57 2,64 2,62 2880 2900
3 10,2 10,0 10,1 5,91 5,79 5,82 5,94 5,83 5,87 3,43 3,37 2895 2920
4 13,3 13,1 13,1 7,69 7,56 7,55 7,70 7,56 7,57 4,45 4,36 2885 2905 1000 -15 / 40 No
5,5 18,9 18,8 18,9 10,9 10,9 10,9 10,7 10,6 10,7 6,20 6,14 2925 2940
7,5 24,8 24,4 24,3 14,3 14,4 14,0 14,4 14,1 14,2 8,32 8,16 2920 2935
11 35,0 33,9 33,0 20,2 19,6 19,1 20,4 19,6 19,2 11,8 11,3 2935 2950
15 47,6 46,1 45,2 27,5 26,6 26,1 27,5 26,6 26,1 15,9 15,3 2940 2950
18,5 58,3 56,7 55,6 33,7 32,7 32,1 34,0 33,0 32,7 19,6 19,0 2940 2950
** Operating conditions to be referred to motor only. About electric pump, refer to limits in users manual. ESHF-IE3-mott18-2p50-en_a_te
21
ESHS SERIES (B35 from 30 to 37 kW)
ESHF SERIES (B3 from 22 to 75 kW)
MOTORI TRIFASE PER SERIE SHS-SHF 50 Hz, 2 poli (da 22kW fino a75kW)
Efficiency N
manufacture
%
Year of
380 V 400 V 415 V
PN Y 660 V Y 690 V IE
kW 4/4 3/4 2/4 4/4 3/4 2/4 4/4 3/4 2/4
22 93,4 93,2 92,7 93,7 93,3 92,5 93,8 93,3 92,3
from 11/2014
30 94,0 94,0 93,1 94,1 94,0 92,8 94,2 93,9 92,6
37 94,4 94,0 93,5 94,6 94,0 93,3 94,7 93,9 93,1
3
45 94,8 94,9 94,6 95,1 95,1 94,6 95,3 95,2 94,5
55 95,1 95,0 94,9 95,4 95,3 94,9 95,5 95,3 94,8
75 95,4 95,2 94,6 95,6 95,3 94,5 95,7 95,3 94,4
Manufacturer
Construction
WEG Equipamentos Eletricos S.A. Data for 400 V / 50 Hz Voltage

IEC SIZE
Design
Reg. No. 07.175.725/0010-50

PN Jaragua do Sul - SC (Brazil) N. of fN TN
22 W22 180M B3 22KW E3 180 B3 0,87 8,00 71,10 2,50 3,30
W22 200L B3 30KW E3 B3
30 200 0,86 7,30 96,60 2,60 2,90
W22 200L B35 30KW E3 B35
W22 200L B3 37KW E3 B3
37 200 2 50 0,86 7,30 119,2 2,60 2,90
W22 200L B35 37KW E3 B35
45 W22 225S/M B3 45KW E3 225 0,88 8,00 144,7 2,70 3,20
55 W22 250S/M B3 55KW E3 250 B3 0,89 7,90 177,1 2,80 2,90
75 W22 280S/M B3 75KW E3 280 0,90 7,60 240,3 2,30 2,90
Voltage UN
V
Y Altitude T. amb ATEX
PN 380 V 400 V 415 V 660 V 690 V nN Above Sea min/max
-1
kW IN (A) min Level (m) C
See note.
22 40,70 39,00 37,90 23,40 22,60 2950 2960

30 55,10 53,50 52,70 31,70 31,00 2960 2970
37 67,70 65,60 64,70 39,00 38,00 2960 2970
1000 -15 / 40 No
45 80,10 77,60 74,60 46,10 45,00 2965 2970
55 97,60 93,50 91,00 56,20 54,20 2960 2965
75 131,0 126,0 121,0 75,40 73,00 2975 2980
Note: Observe the regulations and codes locally in force regarding sorted waste disposal.
22
ESHE SERIES
MOTORI TRIFASE PER SERIE SHE 50 Hz, 4 poli
Efficiency N
manufacture
%
Year of
220 V 230 V 240 V 380 V 400 V 415 V
PN Y 380 V Y 400 V Y 415 V Y 660 V Y 690 V IE
kW 4/4 3/4 2/4 4/4 3/4 2/4 4/4 3/4 2/4 4/4 3/4 2/4 4/4 3/4 2/4 4/4 3/4 2/4
0,25 - - - - - - - - - - - - - - - - - - -
06/2011
0,37 - - - - - - - - - - - - - - - - - - -
0,55 - - - - - - - - - - - - - - - - - - -
0,75 80,4 81,3 79,8 81,1 81,4 79,1 81,4 81,2 78,4 80,4 81,2 78,4 80,4 81,2 78,4 80,4 81,2 78,4 2
1,1 84,9 85,7 84,7 85,3 85,5 83,8 85,3 85 82,7 84,9 85 82,7 84,9 85 82,7 84,9 85 82,7
1,5 86,6 87 85,7 86,7 86,9 84,5 86,4 85,9 83,3 86,4 85,9 83,3 86,4 85,9 83,3 86,4 85,9 83,3
from 11/2014
2,2 87,6 88,6 88,3 88,2 88,8 87,9 88,5 88,7 87,4 87,6 88,6 87,4 87,6 88,6 87,4 87,6 88,6 87,4
3 88,5 89,2 88,5 88,6 88,9 87,6 88,6 88,6 86,8 88,5 88,6 86,8 88,5 88,6 86,8 88,5 88,6 86,8
3
4 88,6 89,1 87,9 88,6 89,1 87,9 88,6 89,1 87,9 88,6 89,2 88,9 88,6 89,2 88,4 88,8 89,1 87,9
5,5 90,4 90,9 89,7 90,4 90,9 89,7 90,4 90,9 89,7 90,4 91,0 90,5 90,9 91,1 90,2 90,9 90,9 89,7
7,5 90,4 91,2 90,4 90,4 91,2 90,4 90,4 91,2 90,4 90,4 91,2 91,1 90,7 91,3 90,8 90,9 91,2 90,4
11 91,5 92,2 91,4 91,5 92,2 91,4 91,5 92,2 91,4 91,5 92,4 92,4 91,9 92,5 92,0 91,9 92,2 91,4
Manufacturer
Construction

IEC SIZE*
Design
Reg. No. 07520560967

0,25 SM471B5/302 71 0,59 3,58 1,71 3,16 2,63
B5
0,37 SM471B5/304 71 0,60 3,39 2,57 3,40 2,47
0,55 SM490RB14S2/305 90R 0,67 3,95 3,77 2,45 2,38
0,75 LLM490RB5S2/307 IE2 90R 0,75 5,78 5,03 2,77 3,31
1,1 PLM490B5S2/311 E3 90 0,71 6,22 7,28 2,75 3,44
1,5 PLM490B5S2/315 E3 90 0,68 6,92 9,89 3,29 4,01
4 50
SPECIAL
2,2 PLM4100B5S3/322 E3 100 0,78 7,47 14,5 2,38 3,69

3 PLM4100B5S3/330 E3 100 0,74 7,75 19,7 2,48 4,21
4 PLM4112B5S3/340 E3 112 0,79 8,32 26,3 3,19 4,02
5,5 PLM4132B14S4/355 E3 132 0,76 7,64 35,9 2,85 3,65
7,5 PLM4132B14S4/375 E3 132 0,79 7,70 49,1 2,69 3,57
11 PLM4160B34S4/3110 E3 160 0,81 7,19 71,5 2,45 3,26
Voltage UN
V

-1
0,25 1,68 1,71 1,77 0,97 0,99 1,02 - - - - - 1375 1400
0,37 2,46 2,53 2,62 1,42 1,46 1,51 - - - - - 1355 1380
0,55 2,98 3,03 3,1 1,72 1,75 1,79 - - - - - 1380 1400
0,75 3,08 3,03 3,01 1,78 1,75 1,74 1,78 1,75 1,74 1,03 1,01 1410 1430
1,1 4,61 4,59 4,62 2,66 2,65 2,67 2,64 2,63 2,65 1,53 1,52 1435 1445
1,5 6,34 6,41 6,41 3,66 3,7 3,7 3,65 3,68 3,69 2,11 2,13 1440 1450
1000 -15 / 40 No
2,2 8,19 8,04 7,97 4,73 4,64 4,6 4,70 4,62 4,56 2,71 2,67 1445 1455
3 11,5 11,5 11,5 6,66 6,62 6,67 6,63 6,59 6,63 3,83 3,81 1450 1460
4 14,8 14,6 14,5 8,52 8,40 8,36 8,40 8,23 8,19 4,85 4,75 1445 1455
5,5 20,0 19,7 19,4 11,6 11,4 11,2 11,7 11,5 11,4 6,75 6,62 1455 1465
7,5 26,6 26,1 25,8 15,4 15,1 14,9 15,5 15,2 15,1 8,95 8,75 1450 1460
11 38,3 37,3 37,5 22,1 21,8 21,7 21,9 21,4 21,3 12,6 12,3 1465 1470
* R = Reduced size of motor casing as compared to shaft extension and flange. ESHE-IE3-mott-4p50-en_a_te
23
ESHS SERIES (B5/B35 from 0,55 to 11 kW)
ESHF SERIES (B3 from 0,25 to 11 kW)
MOTORI TRIFASE PER SERIE ESHS4-ESHF4 50 Hz, 4 poli (fino a 11 kW)
Efficiency N
manufacture
%
Year of
220 V 230 V 240 V 380 V 400 V 415 V
PN Y 380 V Y 400 V Y 415 V Y 660 V Y 690 V IE
kW 4/4 3/4 2/4 4/4 3/4 2/4 4/4 3/4 2/4 4/4 3/4 2/4 4/4 3/4 2/4 4/4 3/4 2/4
0,25 - - - - - - - - - - - - - - - - - - -
06/2011
0,37 - - - - - - - - - - - - - - - - - - -
0,55 - - - - - - - - - - - - - - - - - - -
0,75 80,4 81,3 79,8 81,1 81,4 79,1 81,4 81,2 78,4 80,4 81,2 78,4 80,4 81,2 78,4 80,4 81,2 78,4 2
1,1 84,9 85,7 84,7 85,3 85,5 83,8 85,3 85 82,7 84,9 85 82,7 84,9 85 82,7 84,9 85 82,7
1,5 86,6 87 85,7 86,7 86,9 84,5 86,4 85,9 83,3 86,4 85,9 83,3 86,4 85,9 83,3 86,4 85,9 83,3
from 11/2014
2,2 87,6 88,6 88,3 88,2 88,8 87,9 88,5 88,7 87,4 87,6 88,6 87,4 87,6 88,6 87,4 87,6 88,6 87,4
3 88,5 89,2 88,5 88,6 88,9 87,6 88,6 88,6 86,8 88,5 88,6 86,8 88,5 88,6 86,8 88,5 88,6 86,8
3
4 88,6 89,1 87,9 88,6 89,1 87,9 88,6 89,1 87,9 88,6 89,2 88,9 88,6 89,2 88,4 88,8 89,1 87,9
5,5 90,4 90,9 89,7 90,4 90,9 89,7 90,4 90,9 89,7 90,4 91,0 90,5 90,9 91,1 90,2 90,9 90,9 89,7
7,5 90,4 91,2 90,4 90,4 91,2 90,4 90,4 91,2 90,4 90,4 91,2 91,1 90,7 91,3 90,8 90,9 91,2 90,4
11 91,5 92,2 91,4 91,5 92,2 91,4 91,5 92,2 91,4 91,5 92,4 92,4 91,9 92,5 92,0 91,9 92,2 91,4
Manufacturer
Construction

IEC SIZE
Design
Reg. No. 07520560967

0,25 SM471B3/302 71 0,59 3,58 1,71 3,16 2,63
B3
0,37 SM471B3/304 71 0,60 3,39 2,57 3,40 2,47
SM480B3/305 B3
0,55 80 0,67 3,95 3,77 2,45 2,38
SM480B5/305 B5
LLM480B3/307 IE2 B3
0,75 80 0,75 5,78 5,03 2,77 3,31
LLM480B5/307 IE2 B5
PLM490B3/311 E3 B3
1,1 90 0,71 6,22 7,28 2,75 3,44
PLM490B5/311 E3 B5
PLM490B3/315 E3 B3
1,5 90 0,68 6,92 9,89 3,29 4,01
PLM490B5/315 E3 B5
PLM4100B3/322 E3 B3
2,2 100 4 50 0,78 7,47 14,5 2,38 3,69
PLM4100B5/322 E3 B5
PLM4100B3/330 E3 B3
3 100 0,74 7,75 19,7 2,48 4,21
PLM4100B5/330 E3 B5
PLM4112B3/340 E3 B3
4 112 0,79 8,32 26,3 3,19 4,02
PLM4112B5/340 E3 B5
PLM4132B3/355 E3 B3
5,5 132 0,76 7,64 35,9 2,85 3,65
PLM4132B5/355 E3 B5
PLM4132B3/375 E3 B3
7,5 132 0,79 7,70 49,1 2,69 3,57
PLM4132B5/375 E3 B5
PLM4160B3/3110 E3 B3
11 160 0,81 7,19 71,5 2,45 3,26
PLM4160B35/3110 E3 B35
Voltage UN
V

-1
0,25 1,68 1,71 1,77 0,97 0,99 1,02 - - - - - 1375 1400
0,37 2,46 2,53 2,62 1,42 1,46 1,51 - - - - - 1355 1380
0,55 2,98 3,03 3,10 1,72 1,75 1,79 - - - - - 1380 1400
0,75 3,08 3,03 3,01 1,78 1,75 1,74 1,78 1,75 1,74 1,03 1,01 1410 1430
1,1 4,61 4,59 4,62 2,66 2,65 2,67 2,64 2,63 2,65 1,53 1,52 1435 1445
1,5 6,34 6,41 6,41 3,66 3,7 3,7 3,65 3,68 3,69 2,11 2,13 1440 1450
1000 -15 / 40 No
2,2 8,19 8,04 7,97 4,73 4,64 4,6 4,70 4,62 4,56 2,71 2,67 1445 1455
3 11,5 11,5 11,5 6,66 6,62 6,67 6,63 6,59 6,63 3,83 3,81 1450 1460
4 14,8 14,6 14,5 8,52 8,40 8,36 8,40 8,23 8,19 4,85 4,75 1445 1455
5,5 20,0 19,7 19,4 11,6 11,4 11,2 11,7 11,5 11,4 6,75 6,62 1455 1465
7,5 26,6 26,1 25,8 15,4 15,1 14,9 15,5 15,2 15,1 8,95 8,75 1450 1460
11 38,3 37,3 37,5 22,1 21,8 21,7 21,9 21,4 21,3 12,6 12,3 1465 1470
24
MOTOR NOISE
The tables below show the mean sound pressure levels (Lp) measured at 1 meters distance in a free field according
to the A curve (ISO 1680 standard).
The noise values are measured with idling 50 Hz motor with a tolerance of 3 dB (A).
ESHE, ESHS MOTORS ESHF, ESHC MOTORS

2 POLES 50 Hz 2 POLES 50 Hz
POWER MOTOR TYPE NOISE POWER MOTOR TYPE NOISE
LpA LpA
kW IEC SIZE* dB kW IEC SIZE dB
0,75 90R <70 0,75 80 <70
1,1 90R <70 1,1 80 <70
1,5 90R - 90 <70 1,5 90 <70
2,2 90 <70 2,2 90 <70
3 90 <70 3 100 <70
3 100R <70 4 112 <70
4 112R <70 5,5 132 71
5,5 112 <70 7,5 132 71
5,5 132R <70 11 160 71
7,5 132 71 15 160 71
9,2 132 73 18,5 160 73
11 132 73 22 180 67
11 160R 73 30 200 69
11 160 71 37 200 69
15 160 71 45 225 74
18,5 160 73 55 250 74
22 160 70 75 280 77
22 180R 70
30 200 69
37 200 69
ESHE MOTORS ESHS, ESHF MOTORS

4 POLES 50 Hz 4 POLES 50 Hz
POWER MOTOR TYPE NOISE POWER MOTOR TYPE NOISE
LpA LpA
kW IEC SIZE* dB kW IEC SIZE dB
0,25 71 <70 0,25 71 <70
0,37 71 <70 0,37 71 <70
0,55 90R <70 0,55 80 <70
0,75 90R <70 0,75 80 <70
1,1 90 <70 1,1 90 <70
1,5 90 <70 1,5 90 <70
2,2 100 <70 2,2 100 <70
3 100 <70 3 100 <70
4 112 <70 4 112 <70
5,5 132 <70 5,5 132 <70
7,5 132 <70 7,5 132 <70
11 160 <70 11 160 <70
*R=Reduced size of motor as compared to shaft extension and flange. ESH_mott_a_tr
25
ErP 2009/125/EC
ESH SERIES
PUMPS
Over last decade the European Commission with the Energy Efficiency Plan pushed the European Parliament and the
Council to adopt specific measures to the purpose of reducing energy consumption and further negative environmental
impacts. Through the Directives 2005/32/EC, energy-using products (EuP), and 2009/125/EC, energy-related products
(ErP) a framework for ecodesign requirements was established.
The Commission Regulation (EU) No 547/2012 has implemented two directives with regard to ecodesign
requirements for some types of clean water pumps placed on the market and put into service inside EU zone
as self-alone units or integrated in other products.
For end-suction close-coupled pumps (ESCC for the Regulation) and end-suction own-bearing pumps (ESOB for the
Regulation) the efficiency assessment refers to:
just the pump and not the pump and motor assembly (electric or combustion);
pumps with just one impeller;
pumps with a nominal pressure PN not higher than 16 bar (1600 kPa);
pumps with a minimum nominal flow not less than 6 m3/h;
pumps with a maximum nominal power at the shaft not higher than 150 kW;
pumps designed to operate at a speed of 2900 min-1 (for electric pumps this means 50 Hz 2-pole electric
motors) and with a head not greater than 140 metres;
pumps designed to operate at a speed of 1450 min-1 (for electric pumps this means 50 Hz 4-pole electric
motors) and with a head not greater than 90 metres;
use with clean water at a temperature ranging from -10C to 120C (the test is performed with cold water at a
temperature not higher than 40C).
According to the definitions established in the Regulation ESHE and ESHS versions correspond to the end-suction
close-coupled pump while ESH, ESHF and ESHC versions correspond to the end-suction own bearing pump.
This regulation states that water pumps shall have a minimum index MEI coming from a dedicated formula which
considers hydraulic efficiency values at best efficiency point (BEP), 75 % of the flow at BEP (Part load PL) and 110
% of the flow at BEP (Over load OL).
The Regulation also establishes the following deadlines.

from minimum efficiency index (MEI)
1st January 2013 MEI 0,1
1st January 2015 MEI 0,4
Regulation (EU) n. 547/2012 Annex II point 2 (Product information requirements)

1) Minimum efficiency index: see MEI values in specific tables on following page.
2) The benchmark for most efficient water pumps is MEI 0,70.
3) Year of manufacture: 2014.
4) Manufacturer: Xylem Service Italia Srl - Reg. No 07520560967 - Montecchio Maggiore, Vicenza, Italy.
5) Product type: see the PUMP TYPE column in the tables in the Hydraulic performance section.
6) Hydraulic pump efficiency with trimmed impeller: see p and T columns in the tables in the Hydraulic
performance section.
7) Pump performance curves, including the performance curve: see the Operating Characteristics graphs in the
following pages.
8) The efficiency of a pump with a trimmed impeller is usually lower than that of a pump with the full impeller
diameter. The trimming of the impeller will adapt the pump to a fixed duty point, leading to reduced energy
consumption. The minimum efficiency index (MEI) is based on the full impeller diameter.
9) The operation of this water pump with variable duty points may be more efficient and economic when
controlled, for example, by the use of a variable speed drive that matches the pump duty to the system.
10) Information relevant for disassembly, recycling or disposal at end-of-life: observe the current laws and by-laws
governing sorted waste disposal. Consult the product operating manual.
11) Designed for use below 10 C only: note not applicable to these products.
12) Designed for use above 120 C only: note not applicable to these products.
13) Specific instructions for pumps as per points 11 and 12: not applicable to these products.
14) Information on benchmark efficiency is available at: www.europump.org (Ecodesign section).
15) The benchmark efficiency graphs with MEI = 0.7 and MEI = 0.4 are available at
www.europump.org/efficiencycharts (refer to ESCC 1450 rpm, ESCC 2900 rpm, ESOB 1450 rpm,
ESOB 2900 rpm).
26
ESH SERIES
ESH SERIES
MINIMUM EFFICIENCY
MINIMUM INDEX
EFFICIENCY (MEI) (MEI)
INDEX
2-POLE 4-POLE
ESH, ESHE ESH, ESHE
PUMP SIZE ESHS PUMP SIZE ESHS
ESHF, ESHC ESHF
25-125/128 0,40 0,40 25-125/128 0,40 0,40
25-160/160 0,40 0,40 25-160/160 0,40 0,40
25-200/199 0,40 0,40 25-200/199 0,40 0,40
25-250/245 0,40 0,40 25-250/245 0,40 0,40
32-125/128 0,40 0,40 32-125/128 0,40 0,40
32-160/160 0,40 0,40 32-160/160 0,40 0,40
32-200/199 0,40 0,40 32-200/199 0,40 0,40
32-250/245 0,40 0,40 32-250/245 0,40 0,40
40-125/135 0,40 0,40 40-125/135 0,40 0,40
40-160/171 0,40 0,40 40-160/171 0,40 0,40
40-200/209 0,40 0,40 40-200/209 0,40 0,40
40-250/251 0,40 0,40 40-250/251 0,40 0,40
50-125/137 0,40 0,40 50-125/137 0,40 0,40
50-160/174 0,40 0,40 50-160/174 0,40 0,40
50-200/209 0,40 0,40 50-200/209 0,40 0,40
50-250/250 0,40 0,40 50-250/250 0,40 0,40
65-160/176 0,40 0,40 - - -
65-200/215 0,40 0,40 65-200/219 0,40 0,40
65-250/255 0,40 0,40 65-250/255 0,40 0,40
80-160/186 0,40 0,40 80-160/186 0,40 0,40
80-200/226 0,40 0,40 80-200/220 0,40 0,40
80-250/270 0,40 0,40 80-250/270 0,40 0,40
ESH-MEI-en_a_sc
27
ESH SERIES
HYDRAULIC PERFORMANCE RANGE AT 50 Hz, 2 POLES
28
ESH 25, 32, 40, 50 SERIES
HYDRAULIC PERFORMANCE TABLE AT 50 Hz, 2 POLES
PUMP Q = DELIVERY
TYPE F p % T l/s 0 2,0 2,5 3,1 3,6 4,2 4,7 5,3 5,9 6,4 7,0 7,5 8,1
PN m3/h 0 7 9 11 13 15 17 19 21 23 25 27 29
kW (1) (2) (3) H = TOTAL HEAD METRES COLUMN OF WATER
25-125/07* 0,75 64,0 114 16,3 14,7 13,8 12,8 11,7 10,5 9,2
25-125/11* 1,1 128 66,1 20,8 19,3 18,6 17,6 16,6 15,4 14,2 12,8
25-160/15* 1,5 61,3 145 26,5 25,2 24,2 22,8 21,3 19,4 17,4 15,1 12,5
25-160/22* 2,2 160 63,2 32,8 31,6 30,7 29,5 28,1 26,4 24,6 22,5 20,2 17,7
25-200/30 3 52,5 182 43,0 39,8 38,3 36,6 34,5 32,1 29,4 26,4 23,0
25-200/40 4 199 54,2 52,2 49,0 47,6 45,9 44,0 41,7 39,3 36,5 33,4 30,1
25-250/55 5,5 47,6 208 57,7 55,9 54,8 53,3 51,5 49,6 47,4 44,7 41,2
25-250/75 7,5 49,2 228 70,5 68,4 67,5 66,2 64,6 62,7 60,6 58,4 55,8 52,7
25-250/110 11 245 50,7 82,6 80,3 79,4 78,2 76,6 74,8 72,8 70,7 68,3 65,7
32-125/07* 0,75 62,2 114 16,1 14,5 13,6 12,5 11,2 9,7 8,1 6,4
32-125/11* 1,1 128 64,4 20,6 19,2 18,4 17,3 16,1 14,8 13,3 11,7 10,0
32-160/15* 1,5 58,3 145 26,9 24,9 23,8 22,3 20,6 18,5 16,2 13,7 11,1
32-160/22* 2,2 160 60,2 33,1 31,3 30,3 29,0 27,5 25,6 23,5 21,2 18,7 16,0
32-200/30 3 50,8 182 43,4 39,2 37,6 35,6 33,3 30,6 27,7 24,4 20,9
32-200/40 4 199 52,5 52,6 48,3 46,8 44,9 42,8 40,3 37,6 34,5 31,2 27,6
32-250/55 5,5 46,1 208 57,5 55,7 55,0 53,9 52,4 50,5 48,3 45,9 43,2
32-250/75 7,5 47,7 228 70,3 67,5 66,5 65,2 63,5 61,5 59,2 56,7 54,0 50,9
32-250/110 11 245 49,2 82,3 79,2 78,3 77,0 75,4 73,6 71,4 69,1 66,5 63,7 60,6 57,2
PUMP Q = DELIVERY
TYPE F p % T l/s 0 5,0 5,8 6,7 7,5 8,3 9,2 10,0 10,8 11,7 12,5 13,3 14,2
PN m3/h 0 18 21 24 27 30 33 36 39 42 45 48 51
40-125/11* 1,1 66,6 111 15,7 12,8 11,8 10,7 9,5 8,3 6,9 5,5 4,0
40-125/15* 1,5 68,2 122 19,1 16,4 15,5 14,4 13,3 12,1 10,8 9,4 8,0 6,5
40-125/22* 2,2 135 70,1 23,7 21,1 20,2 19,2 18,1 17,0 15,7 14,4 13,0 11,5 10,1
40-160/30 3 67,5 159 32,1 29,4 28,3 27,0 25,6 24,1 22,5 20,7 18,9 17,0 15,1
40-160/40 4 171 69,5 37,9 35,4 34,4 33,2 31,8 30,2 28,5 26,7 24,8 22,7 20,7 18,6
40-200/55 5,5 65,0 190 49,1 46,3 45,2 43,8 42,2 40,4 38,4 36,1 33,7 31,0 28,1 25,0
40-200/75 7,5 209 66,5 58,2 55,1 53,9 52,4 50,8 49,0 47,0 44,9 42,5 40,0 37,3 34,4
40-250/92 9,2 58,0 218 64,9 62,0 60,9 59,6 58,1 56,2 54,1 51,5 48,4 44,6
40-250/110A 11,0 58,0 218 64,9 62,0 60,9 59,6 58,1 56,2 54,1 51,5 48,4 44,6
40-250/110 11 58,5 233 74,6 71,3 70,3 69,0 67,6 65,9 63,8 61,5 58,6 55,2 51,3
40-250/150 15 251 59,0 87,7 84,0 82,9 81,6 80,1 78,4 76,6 74,4 72,0 69,3 66,1 62,4 58,2
PUMP Q = DELIVERY
TYPE F p % T l/s 0 10 11 12,73 14,09 15,45 16,82 18,18 19,55 20,91 22,27 23,636 25
PN m3/h 0 36 41 46 51 56 61 65 70 75 80 85 90
50-125/22* 2,2 72,9 114 16,8 14,3 13,4 12,4 11,2 9,8 8,4 6,9 5,4
50-125/30 3 74,6 125 20,4 18,2 17,4 16,5 15,4 14,2 12,9 11,4 9,9 8,3
50-125/40 4 137 76,5 24,7 22,7 22,0 21,2 20,3 19,2 18,0 16,7 15,3 13,8 12,2
50-160/55 5,5 72,0 158 34,0 30,5 29,5 28,3 26,9 25,5 23,9 22,2 20,4 18,5 16,4
50-160/75 7,5 174 74,0 40,7 37,4 36,3 35,2 33,9 32,6 31,0 29,4 27,6 25,6 23,5 21,1 18,6
50-200/92 9,2 70,0 197 52,9 47,4 45,8 43,8 41,7 39,3 36,7 33,8 30,7 27,4 23,7
50-200/110A 11 70,0 197 52,9 47,4 45,8 43,8 41,7 39,3 36,7 33,8 30,7 27,4 23,7
50-250/110 11 209 72,0 38,5 54,5 37,9 37,3 36,4 35,2 33,6 31,6 29,3 26,5 23,5 27,2
50-250/150 15 69,5 224 70,2 66,6 65,4 64,0 62,4 60,4 58,1 55,3 52,0 48,1
50-250/185 18,5 68,4 237 79,9 74,9 73,6 72,1 70,4 68,4 66,2 63,6 60,7 57,3 53,4
50-250/220 22 250 67,3 88,9 84,5 83,7 82,8 81,9 80,9 79,8
Hydraulic performances in compliance with ISO 9906:2012 - Grade 3B (ex ISO 9906:1999 - Annex A)
(1) External diameter of full impeller (2) Hydraulic efficiency of pump (3) External diameter of trimmed impeller. ESH-25-32-40-50_2p50-en_a_th
*Available also in single-phase version.
29
ESH 65, 80 SERIES
TABELLA DI PRESTAZIONI
HYDRAULIC IDRAULICHE
PERFORMANCE SERIE AT
TABLE ESH50
65,Hz,
80 2
2 poli
POLES50 Hz
PUMP Q = DELIVERY
TYPE F p % T l/s 0 13 14,77 16,96 19,15 21,34 23,53 25,72 27,91 30,1 32,29 34,477 37
3
PN m /h 0 45 53 61 69 77 85 93 100 108 116 124 132
65-160/40 4 72,1 127 21,1 17,2 15,7 14,1 12,3 10,6 8,7
65-160/55 5,5 73,9 140 25,8 22,5 21,1 19,5 17,8 16,1 14,2 12,3 10,3
65-160/75 7,5 75,7 154 31,5 28,8 27,5 26,0 24,4 22,6 20,8 18,9 16,9 14,9
65-160/92 9,2 73,0 164 36,3 33,8 32,2 30,3 28,2 25,9 23,6 21,4 19,4 17,7
65-160/110A 11 73,0 164 36,3 33,8 32,2 30,3 28,2 25,9 23,6 21,4 19,4 17,7
65-160/110 11 176 74,4 42,1 40,1 38,7 37,0 35,0 32,8 30,5 28,1
65-200/150 15 71,7 192 52,4 50,3 49,2 47,9 46,2 44,3 42,1 39,6 36,8
65-200/185 18,5 72,8 203 59,3 56,4 55,2 53,7 51,9 49,9 47,6 45,0 42,2
65-200/220 22 215 74,0 31,1 30,3 28,4 25,0 20,2 56,1 53,7 51,1 48,2 45,0
65-250/300 30 74,5 240 83,7 81,5 80,2 78,6 76,7 74,4 71,9 69,0 65,8 62,3
65-250/370 37 255 73,5 96,5 94,8 93,3 91,6 89,6 87,3 84,8 82,0 79,0 75,7 72,2
PUMP Q = DELIVERY
TYPE F p % T l/s 0 20 24,24 28,48 32,73 36,97 41,21 45,45 49,7 53,94 58,18 62,424 67
PN m3/h 0 72 87 103 118 133 148 164 179 194 209 225 240
80-160/110 11 75,0 169 33,0 31,8 30,3 28,4 26,1 23,5 20,7 17,7 14,6 11,5
80-160/150 15 76,5 177 39,5 38,7 37,2 35,4 33,2 30,7 27,9 24,9 21,7 18,5 15,2
80-160/185 18,5 186 78,0 46,4 45,6 44,1 42,4 40,3 37,9 35,3 32,4 29,3 26,1 22,6
80-200/220 22 80,5 198 51,8 51,4 50,0 48,2 46,2 43,8 41,2 38,4 35,4 32,1 28,6
80-200/300 30 81,0 215 62,3 62,6 61,3 59,7 57,7 55,3 52,6 49,7 46,5 43,1 39,6 36,0
80-200/370 37 226 81,5 69,8 70,8 69,7 68,2 66,4 64,2 61,7 58,9 55,8 52,5 48,9 45,2 41,3
80-250/450 45 79,5 237 82,2 78,7 76,4 73,7 70,5 66,9 63,0 58,6 53,8
80-250/550 55 80,0 252 93,9 91,8 89,6 87,1 84,1 80,7 77,0 72,9 68,5
80-250/750 75 270 78,0 109,6 108,4 106,4 103,9 101,1 97,9 94,3 90,4 86,0 81,2
Hydraulic performances in compliance with ISO 9906:2012 - Grade 3B (ex ISO 9906:1999 - Annex A) ESH-65-80_2p50-en_a_th
(1) External diameter of full impeller (2) Hydraulic efficiency of pump (3) External diameter of trimmed impeller
30
ESH SERIES
31
ESH 25, 32, 40, 50 SERIES
PUMP Q = DELIVERY
TYPE F p % T l/s 0 1,3 1,6 1,9 2,2 2,5 2,8 3,1 3,4 3,7 4,0 4,3 4,6
PN m3/h 0 5 6 7 8 9 10 11 12 13 14 15 17
25-125/02A 0,25 58,5 114 4,0 3,5 3,2 2,9 2,6 2,2 1,7
25-125/02 0,25 128 60,8 5,2 4,7 4,4 4,1 3,8 3,4 3,0 2,5
25-160/02A 0,25 57,4 145 6,5 6,0 5,7 5,3 4,8 4,3 3,8 3,2
25-160/02 0,25 160 59,4 8,0 7,5 7,2 6,9 6,5 6,0 5,5 4,9 4,3
25-200/03 0,37 50,4 182 10,4 9,4 8,9 8,4 7,8 7,1 6,3 5,5 4,6 3,6
25-200/05 0,55 199 52,2 12,5 11,6 11,1 10,6 10,0 9,4 8,7 7,9 7,0 6,1 5,1
25-250/07 0,75 46,8 208 14,4 13,6 13,3 12,9 12,5 11,9 11,3 10,5 9,8 8,9 8,1
25-250/11 1,1 48,4 228 17,5 16,7 16,4 16,1 15,7 15,1 14,6 13,9 13,2 12,4 11,5 10,7
25-250/15 1,5 245 49,7 20,4 19,6 19,3 19,0 18,6 18,1 17,6 17,0 16,3 15,5 14,7 13,9 13,0
32-125/02A 0,25 59,9 114 4,0 3,6 3,4 3,1 2,8 2,4 2,0 1,5
32-125/02 0,25 128 62,3 5,2 4,8 4,6 4,3 4,0 3,6 3,3 2,8 2,4 1,9
32-160/02A 0,25 58,0 145 6,6 6,0 5,7 5,3 4,8 4,2 3,6 2,9
32-160/02 0,25 160 60,0 8,1 7,5 7,2 6,9 6,4 5,9 5,4 4,7 4,0 3,3 2,5
32-200/03 0,37 49,9 182 10,5 9,4 8,9 8,4 7,7 7,0 6,2 5,3 4,3 3,2
32-200/05 0,55 199 51,6 12,7 11,6 11,2 10,6 10,0 9,3 8,5 7,7 6,8 5,8 4,7
32-250/07 0,75 44,0 208 14,2 13,5 13,2 12,8 12,3 11,7 11,0 10,2 9,3 8,3 7,1
32-250/11 1,1 45,6 228 17,4 16,6 16,3 15,9 15,5 14,9 14,3 13,6 12,8 11,9 10,9 9,8
32-250/15 1,5 245 46,9 20,3 19,5 19,2 18,9 18,4 17,9 17,3 16,7 15,9 15,1 14,2 13,2 12,2
PUMP Q = DELIVERY
TYPE F p % T l/s 0 2,5 2,9 3,4 3,8 4,2 4,6 5,1 5,5 5,9 6,4 6,8 7,2
3
PN m /h 0 9 11 12 14 15 17 18 20 21 23 24 26
40-125/02A 0,25 66,2 122 4,5 3,7 3,4 3,2 2,9 2,6 2,2
40-125/02 0,25 135 68,2 5,6 4,8 4,5 4,3 4,0 3,7 3,4 3,0 2,7 2,3 2,0
40-160/03 0,37 67,6 159 8,0 7,2 6,9 6,6 6,3 5,9 5,5 5,0 4,6 4,1 3,5
40-160/05 0,55 171 66,5 9,2 8,5 8,2 7,9 7,6 7,2 6,8 6,3 5,8 5,3 4,8 4,2
40-200/07 0,75 64,3 190 11,9 11,2 10,9 10,5 10,1 9,6 9,1 8,5 7,8 7,1 6,4
40-200/11 1,1 209 62,9 14,2 13,3 13,0 12,6 12,2 11,8 11,2 10,7 10,0 9,3 8,6 7,7
40-250/11 1,1 55,8 218 15,6 14,6 14,3 13,9 13,5 13,0 12,4 11,7 11,0 10,1
40-250/15 1,5 57,0 233 18,1 17,0 16,7 16,3 15,9 15,5 14,9 14,3 13,7 12,9 12,1
40-250/22 2,2 251 58,1 21,5 20,4 20,0 19,6 19,2 18,7 18,2 17,6 16,9 16,2 15,4 14,6 13,6
PUMP Q = DELIVERY
TYPE F p % T l/s 0 5 6 6,364 7,045 7,727 8,409 9,091 9,773 10,45 11,14 11,818 12,5
PN m3/h 0 18 20 23 25 28 30 33 35 38 40 43 45
50-125/02 0,25 71,5 114 4,1 3,4 3,1 2,9 2,6 2,3 2,0 1,7 1,3 0,9
50-125/03 0,37 73,2 125 5,0 4,3 4,1 3,9 3,6 3,3 3,0 2,7 2,3 2,0 1,6
50-125/05 0,55 137 75,1 6,0 5,4 5,2 5,0 4,8 4,5 4,2 3,9 3,6 3,2 2,9 2,5 2,1
50-160/07 0,75 71,3 158 8,2 7,3 7,1 6,8 6,5 6,2 5,8 5,5 5,1 4,6 4,2
50-160/11 1,1 174 73,0 9,8 8,8 8,6 8,3 8,0 7,7 7,4 7,0 6,7 6,3 5,8 5,3 4,8
50-200/11 1,1 69,1 197 12,8 11,2 10,7 10,2 9,7 9,1 8,5 7,8 7,1 6,3 5,5
50-200/15 1,5 209 70,1 14,7 13,0 12,6 12,1 11,5 10,9 10,3 9,6 8,9 8,1 7,3 6,4 5,5
50-250/22A 2,2 70,0 224 38,5 16,0 37,9 37,3 36,4 35,2 33,6 31,6 29,3 26,5 23,5
50/250/22 2,2 69,0 237 19,4 17,8 17,4 17,0 16,5 16,0 15,4 14,8 14,0 13,2 12,3 11,3
50-250/30 3 250 67,9 21,9 20,6 20,2 19,8 19,4 18,8 18,3 17,6 17,0 16,2 15,4 14,5 13,5
Hydraulic performances in compliance with ISO 9906:2012 - Grade 3B (ex ISO 9906:1999 - Annex A) ESH-25-32-40-50_4p50-en_a_th
(1) Diametro esterno girante piena (2) Efficienza idraulica della pompa (3) Diametro esterno girante ridotta (tornita).
32
ESH 65, 80 SERIES
TABELLA DI PRESTAZIONI
HYDRAULIC IDRAULICHE
PERFORMANCE SERIE ESH
RANGE 65, 80
AT 50 Hz,44poli 50 Hz
POLES
PUMP Q = DELIVERY
TYPE F p % T l/s 0 8 8,788 10,08 11,36 12,65 13,94 15,23 16,52 17,8 19,09 20,379 22
3
PN m /h 0 27 32 36 41 46 50 55 59 64 69 73 78
65-200/15 1,5 68,2 176 10,7 9,8 9,3 8,7 8,1 7,3 6,3 5,3 4,0
65-200/22 2,2 70,2 199 13,8 13,1 12,7 12,2 11,6 11,0 10,2 9,3 8,4 7,3
65-200/30 3 219 72,0 16,9 16,3 15,9 15,5 15,0 14,4 13,8 13,0 12,1 11,2 10,2
65-250/40 4 71,9 240 20,4 19,3 18,8 18,3 17,6 16,9 16,1 15,2 14,2 13,0
65-250/55 5,5 255 71,0 23,7 23,1 22,6 22,0 21,4 20,7 19,9 19,1 18,1 17,1 16,0 14,7
PUMP Q = DELIVERY
TYPE F p % T l/s 0 10 12,73 15,45 18,18 20,91 23,64 26,36 29,09 31,82 34,55 37,273 40
PN m3/h 0 36 46 56 65 75 85 95 105 115 124 134 144
80-160/15 1,5 75,2 169 8,0 7,6 7,0 6,3 5,6 4,8 4,0 3,1
80-160/22A 2,2 74,2 177 9,4 9,0 8,5 7,8 7,1 6,3 5,4 4,5 3,5
80-160/22 2,2 186 73,4 10,8 10,4 9,9 9,2 8,5 7,7 6,8 5,9 4,9
80-200/30 3 80,5 198 12,3 11,9 11,2 10,4 9,5 8,5 7,5 6,4 5,3
80-200/40 4 220,0 78,3 15,4 15,3 14,7 13,9 13,0 12,1 11,1 10,1 9,0 7,9
80-250/55 5,5 77,5 237 20,3 19,5 19,2 18,9 18,5 18,1 17,6 17,2 16,6
80-250/75 7,5 76,7 252 23,1 22,2 21,9 21,6 21,3 20,9 20,5 20,1 19,7
80-250/110 11 270 74,3 26,6 26,1 25,8 25,5 25,2 24,8 24,5 24,1 23,6
Hydraulic performances in compliance with ISO 9906:2012 - Grade 3B (ex ISO 9906:1999 - Annex A) ESH-65-80_4p50_a_th
(1) External diameter of full impeller (2) Hydraulic efficiency of pump (3) External diameter of trimmed impeller.
33
ESH SERIES
IDENTIFICATION OF IMPELLER TYPOLOGY
[%]
[%]
04940_B_SC
34
ESH SERIES
OPERATING CHARACTERISTICS AT 50 Hz, 2 POLES
ESH 25-125 ~ 2900 [rpm] ISO 9906:2012 - Grade 3B
0 10 20 30 40 50 60 70 80 90 gpm]
Q [Imp
0 20 40 60 80 100 Q [US gpm]

25
80
[%]
70
20 55
57
59
61
63 60
65
15 66.1 50
65
40
H [ft]
H[m]
25-125/11
128
10 64.0
30
25-125/07
114 20
5
10
0 0
2
6
NPSH [ft]
NPSH[m]
4
1
25-125/11
128 2
0 0
1.5 2
2
1.0 25-125/11
128
Pp[kW]
1
PP[HP]
25-125/07
0.5 114
1
ESH25-125_2P50_A_CH
0.0 0
0 5 10 15 20 Q25
[m3/h]
0 1 2 3 4 5 6 Q [l/s]
The NPSH values are laboratory values; for practical use we suggest increasing these values by 0,5 m.
These performances are valid for liquids with density = 1,0 Kg/dm3 and kinematic viscosity = 1 mm2/sec.
35
ESH SERIES
0 20 40 60 80 100 Q [Imp gpm]
0 20 40 60 80 100 120 Q [US gpm]

35
48 50.5
53 [%]
55.5
30
58 100
60.5
63.2
25 80
61.3
20 60.5
58 60
H [ft]
H[m]
15 25-160/22
160
40
10 25-160/15
145
20
5
0 0
4
3 10
NPSH [ft]
NPSH[m]
2
25-160/22 5
160
1
0 0
2.5
3.0
2.0
25-160/22 2.5
160
1.5 2.0
Pp[kW]
25-160/15
PP[HP]
145 1.5
1.0
1.0
0.5
0.5
ESH25-160_2P50_A_CH
0.0 0.0
0 5 10 15 20 25 Q30
[m3/h]
0 1 2 3 4 5 6 7 8 Q [l/s]
36
ESH SERIES
0 20 40 60 80 100 Q [Imp gpm]
0 20 40 60 80 100 120 Q [US gpm]

60
[%] 180
42
50 44
46
48 160
50
52
140
40 54.2
120
52.5
52
30 50 100
H [ft]
H[m]
25-200/40 80
199
20
60
25-200/30
182
40
10
20
0 0
5
15
4
NPSH [ft]
NPSH[m]
3 10
25-200/40
2 199
5
1
0 0
5
6
4
25-200/40 5
199
3 4
Pp[kW]
25-200/30
PP[HP]
182 3
2
2
1
1
ESH25-200_2P50_A_CH
0 0
0 5 10 15 20 25 Q30
[m3/h]
0 1 2 3 4 5 6 7 8 Q [l/s]
37
ESH SERIES
0 20 40 60 80 100 Q [Imp gpm]
0 20 40 60 80 100 120 Q [US gpm]

90
35.5 38 [%]
80 40.5
43
45.5 250
48
70
50.7
60 25-250/110 200
49.2
245
50 47.6
25-250/75
150
228
H [ft]
H[m]
40
25-250/55
208 100
30
20
50
10
0 0
30
8 25-250/110
245
NPSH [ft]
NPSH[m]
20
4
10
0 0
10
12
25-250/110
8 245 10
25-250/75
6 228 8
Pp[kW]
25-250/55
PP[HP]
208 6
4
4
2
2
ESH25-250_2P50_A_CH
0 0
0 5 10 15 20 25 Q30
[m3/h]
0 1 2 3 4 5 6 7 8 Q [l/s]
38
ESH SERIES
0 10 20 30 40 50 60 70 80 90 gpm]
Q [Imp
0 20 40 60 80 100 Q [US gpm]

25
80
[%]
49
70
51.5
20 54
56.5
59
61.5
60
64.4
15 50
61.5
40
H [ft]
H[m]
59
62.2
56.5
10
30
32-125/11
128
20
5
32-125/07
114 10
0 0
2
6
NPSH [ft]
NPSH[m]
4
1 32-125/11
128
2
0 0
1.5 2.0
1.5
1.0 32-125/11
Pp[kW]
128
1.0
PP[HP]
32-125/07
0.5 114
0.5
ESH32-125_2P50_A_CH
0.0 0.0
0 5 10 15 20 Q25
[m3/h]
0 1 2 3 4 5 6 Q [l/s]
39
ESH SERIES
0 20 40 60 80 100 Q [Imp gpm]
0 20 40 60 80 100 120 Q [US gpm]

35
45
47.5 [%]
50
52.5
30 55 100
57.5
60.2
25 80
58.3
20 57.5
55 60
52.5
H [ft]
H[m]
15 50
47.5
40
32-160/22
10 160
32-160/15
145
20
5
0 0
4
3 10
NPSH [ft]
NPSH[m]
32-160/22
2 160
5
1
0 0
2.5
3.0
2.0
32-160/22 2.5
160
1.5 2.0
Pp[kW]
32-160/15
PP[HP]
145 1.5
1.0
1.0
0.5
0.5
ESH32-160_2P50_A_CH
0.0 0.0
0 5 10 15 20 25 Q30
[m3/h]
0 1 2 3 4 5 6 7 8 Q [l/s]
40
ESH SERIES
0 20 40 60 80 100 Q [Imp gpm]
0 20 40 60 80 100 120 Q [US gpm]

60
[%] 180
37.5 40
50 42.5
45 160
47.5
50
140
40 52.5
120
50.8
50
30 47.5 100
H [ft]
H[m]
45
80
32-200/40
20 199
60
32-200/30
182 40
10
20
0 0
5
15
4
NPSH [ft]
NPSH[m]
3 32-200/40 10
199
2
5
1
0 0
5
6
4
32-200/40
5
199
3 4
Pp[kW]
32-200/30
PP[HP]
182 3
2
2
1
1
ESH32-200_2P50_A_CH
0 0
0 5 10 15 20 25 Q30
[m3/h]
0 1 2 3 4 5 6 7 8 Q [l/s]
41
ESH SERIES
0 20 40 60 80 100 Q [Imp gpm]
0 20 40 60 80 100 120 Q [US gpm]

90
34 36.5
[%]
80 39
41.5
44 250
46.5
70
49.2
60 200
47.7
32-250/110
50 245
46.1
32-250/75 150
H [ft]
H[m]
40 228
32-250/55
208
30 100
20
50
10
0 0
12
32-250/110
245
30
8
NPSH [ft]
NPSH[m]
20
4
10
0 0
10
12
32-250/110
8 245 10
32-250/75
6 228 8
Pp[kW]
PP[HP]
32-250/55 6
4 208
4
2
2
ESH32-250_2P50_A_CH
0 0
0 5 10 15 20 25 Q30
[m3/h]
0 1 2 3 4 5 6 7 8 Q [l/s]
42
ESH SERIES
0 20 40 60 80 100 120 140 160 180 gpm]

Q [Imp
0 50 100 150 200 Q [US gpm]

25
80
58 [%]
60
62
64
66 70
68
20
70.1 60
15 50
68.2
68 66
64
40
H [ft]
62
H[m]
60
66.6
10
30
40-125/22
135
20
40-125/15
5
122
40-125/11 10
111
0 0
3
8
2
NPSH [ft]
NPSH[m]
40-125/22 6
135
4
1
2
0 0
3 4
3
2
40-125/22
Pp[kW]
135
2
PP[HP]
40-125/15
122
1
40-125/11
1
111
ESH40-125_2P50_A_CH
0 0
0 10 20 30 40 Q50
[m3/h]
0 2 4 6 8 10 12 Q [l/s]
43
ESH SERIES
0 50 100 150 200 Q [Imp gpm]
0 50 100 150 200 250

Q [US gpm]
40
120
[%]
63
65
67
69
30 100
69.5
69
67.5
67
80
65
20 63
40-160/40
H [ft]
60
H[m]
171
40-160/30
159
40
10
20
0 0
6
15
4 40-160/40
NPSH [ft]
NPSH[m]
171
10
2
5
0 0
5
6
4 40-160/40
171 5
3 40-160/30 4
Pp[kW]
159
PP[HP]
3
2
2
1
1
ESH40-160_2P50_A_CH
0 0
0 10 20 30 40 50 Q60
[m3/h]
0 2 4 6 8 10 12 14 16 Q [l/s]
44
ESH SERIES
0 50 100 150 200 Q [Imp gpm]
0 50 100 150 200 250Q [US gpm]

60
180
[%]
60
62
50 64
160
65.0
140
64
40 65
66
62 120
66.5
60
66
30 65 40-200/75 100
209
H [ft]
H[m]
40-200/55 80
190
20
60
40
10
20
0 0
8
40-200/75
6 209 20
NPSH [ft]
NPSH[m]
4
10
2
0 0
8
40-200/75 10
209
6 40-200/55
40-200/55 8
190
190
6
Pp[kW]
4
PP[HP]
4
2
2
ESH40-200_2P50_A_CH
0 0
0 10 20 30 40 50 Q60
[m3/h]
0 2 4 6 8 10 12 14 16 Q [l/s]
45
ESH SERIES
0 50 100 150 200 Q [Imp gpm]
0 50 100 150 200 250

Q [US gpm]
90
45
50 52
[%]
80 55
57 250
58.0
70
57
60
58.5
40-250/150 200
251
59.0
50 40-250/110
233 150
H [ft]
H[m]
40 40-250/**
218
30 100
20
50
10
0 0
8
40-250/**
6 218 20
40-250/150
NPSH [ft]
NPSH[m]
251
4
10
2
0 0
16
40-250/150 20
14 251
12 40-250/110
15
233
10
40-250/**
Pp[kW]
8 218
PP[HP]
10
6
4 5
ESH40-250_2P50_A_CH
2
0 0
0 10 20 30 40 50 Q60
[m3/h]
0 2 4 6 8 10 12 14 16 Q [l/s]
**= 9.2 kW (/92) ESHE, **= 11 kW (/110A) ESHS, ESHF, ESHC
46
ESH SERIES
0 50 100 150 200 250 300 Q [Imp gpm]
0 50 100 150 200 250 300 350 Q [US gpm]

25
62.5 65 80
67.5
70
72.5 [%]
75
70
20 76.5
60
75
72.5
15 74.6
50
70
67.5
72.9 65 40
H [ft]
H[m]
62.5
10
50-125/40 30
137
50-125/30 20
125
5
50-125/22
114 10
0 0
5
15
4
NPSH [ft]
NPSH[m]
3 10
50-125/40
2 137
5
1
0 0
5
6
4
50-125/40 5
137
3 4
Pp[kW]
50-125/30
PP[HP]
125 3
2
50-125/22
114 2
1
1
ESH50-125_2P50_A_CH
0 0
0 10 20 30 40 50 60 70 80 Q90
[m3/h]
0 5 10 15 20 Q [l/s]
25
47
ESH SERIES
0 50 100 150 200 250 300 350

Q [Imp gpm]
0 50 100 150 200 250 300 350 400 Q [US gpm]

50
160
45
140
40 64 [%]
66
68
70 120
35 72
74
30 100
72
72
70
25 80
H [ft]
68
H[m]
66
64
20
60
50-160/75
15 174
50-160/55
40
10 158
20
5
0 0
8
50-160/55
6 158 20
50-160/75
NPSH [ft]
NPSH[m]
174
4
10
2
0 0
8
10
7
50-160/75
6 174 8
5 50-160/55
6
Pp[kW]
158
4
PP[HP]
3 4
2
2
ESH50-160_2P50_A_CH
1
0 0
0 10 20 30 40 50 60 70 80 90 Q100
[m3/h]
0 5 10 15 20 25 Q [l/s]
48
ESH SERIES
0 50 100 150 200 250 300 Q350

[Imp gpm]
0 50 100 150 200 250 300 350 400 Q [US gpm]

70
[%]
60 200
62
64 66
68
70
50 72.0
150
40 70
70.0 68
H[m]
H [ft]
66
64
30 62 100
50-200/110
209
20
50-200/**
197 50
10
0 0
8
50-200/**
197 50-200/110
6 209
20
NPSH [ft]
NPSH[m]
4
10
2
0 0
12 16
50-200/110
209 14
10
50-200/** 12
8 197
10
Pp[kW]
6 8
PP[HP]
6
4
4
2
ESH50-200_2P50_A_CH
2
0 0
0 20 40 60 80 Q100
[m3/h]
0 5 10 15 20 25 Q [l/s]
**= 9.2 kW (/92) ESHE, **= 11 kW (/110A) ESHS, ESHF, ESHC
49
ESH SERIES
0 50 100 150 200 250 300 350

Q [Imp gpm]
0 50 100 150 200 250 300 350 400 Q [US gpm]

100
300
[%]
90
60
62
64
80 66
67.3
250
70
66
64
60 68.4 200
68
50-250/220
69.5 250
50
68 50-250/185
H [ft]
150
H[m]
237
40 50-250/150
224
30 100
20
50
10
0 0
6 50-250/150
224 50-250/220
250 15
4
NPSH [ft]
NPSH[m]
10
2
5
0 0
24
50-250/220 30
20 250
50-250/185
25
16 237
20
Pp[kW]
50-250/150
12
PP[HP]
224 15
8 10
4 5
ESH50-250_2P50_A_CH
0 0
0 10 20 30 40 50 60 70 80 90 Q100
[m3/h]
0 5 10 15 20 25 Q [l/s]
50
ESH SERIES
0 100 200 300 400 500 Q [Imp gpm]
0 100 200 300 400 500 600 Q [US gpm]

44
64 68 140
72
40 [%]
74.4
36 120
72
32 73.0
100
28 68
75.7 65-160/110
176
24 80
73.9
H [ft]
20
H[m]
64 65-160/**
72.1 164 60
16
65-160/75
12 154 40
8 65-160/55
65-160/40
140 20
4 127
0 0
8
6 20
NPSH [ft]
NPSH[m]
4
10
2
0 0
15 20
65-160/110
176
65-160/** 15
10 164
Pp[kW]
65-160/75
10
PP[HP]
154
5 65-160/55
65-160/40
140 5
127
ESH65-160_2P50_A_CH
0 0
0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 Q150
[m3/h]
0 5 10 15 20 25 30 35 40 Q [l/s]
**= 9.2 kW (/92) ESHE **= 11 kW (/110A) ESHS, ESHF, ESHC
51
ESH SERIES
0 100 200 300 400 500 Q [Imp gpm]
0 100 200 300 400 500 600 Q [US gpm]

70
60 62.5 65
67.5
70 [%]
72.5
60 200
74.0
72.8 72.5
50
70
150
65-200/220
71.7 215
40
65-200/185
203
H [ft]
H[m]
65-200/150
30 192
100
20
50
10
0 0
8
65-200/220
6 215 20
NPSH [ft]
NPSH[m]
4
10
2
0 0
25
65-200/220 30
215
20
65-200/185 25
203
15 65-200/150 20
Pp[kW]
192
PP[HP]
15
10
10
5
5
ESH65-200_2P50_A_CH
0 0
0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 Q150
[m3/h]
0 5 10 15 20 25 30 35 40 Q [l/s]
52
ESH SERIES
0 100 200 300 400 500 Q [Imp gpm]
0 100 200 300 400 500 600 Q [US gpm]

120
[%]
350
100 65
68 70
72
73 300
73.5
73
80 72
74.5 70 250
65-250/370
60 255 200
H [ft]
H[m]
65-250/300
240
150
40
100
20
50
0 0
10
65-250/300 30
240
8
65-250/370
NPSH [ft]
NPSH[m]
6 20
255
4
10
2
0 0
40
50
65-250/370
255
30 40
65-250/300
240
30
Pp[kW]
20
PP[HP]
20
10
10
ESH65-250_2P50_A_CH
0 0
0 20 40 60 80 100 120 140 Q [m3/h]
0 5 10 15 20 25 30 35 40 Q [l/s]
53
ESH SERIES
0 100 200 300 400 500 600 700 800 900 gpm]
Q [Imp
0 200 400 600 800 1000 Q [US gpm]

50
160
68
70
45 72
74 [%]
76 140
40
78.0
120
35
76.5
30 76 100
74
72
25 70 80
H [ft]
H[m]
75.0
68
20
80-160/185 60
15 186
80-160/150 40
10 177
80-160/110
169x15 20
5
0 0
8
80-160/110
6 169x15 20
80-160/185
NPSH [ft]
NPSH[m]
186
4
10
2
0 0
20
25
80-160/185
15 186 20
80-160/150
15
Pp[kW]
177
10
PP[HP]
80-160/110
169x15 10
5
5
ESH80-160_2P50_A_CH
0 0
0 50 100 150 200 250
Q [m3/h]
0 10 20 30 40 50 60 Q [l/s]
54
ESH SERIES
0 200 400 600 800 1000 Q [Imp gpm]
0 200 400 600 800 1000 1200 Q [US gpm]

80
[%] 250
70
70 75
78
80
81
81.5 200
60
81
80
50 78
81.0
75 150
40 80-200/370
80.5
H [ft]
H[m]
226
80-200/300
30 100
215
80-200/220
20 198
50
10
0 0
8
80-200/220 80-200/370
6 198
20
226
NPSH [ft]
NPSH[m]
4
10
2
0 0
40
80-200/370 50
35 226
30 80-200/300 40
215
25 80-200/220
30
Pp[kW]
198
20
PP[HP]
15 20
10
10
ESH80-200_2P50_A_CH
5
0 0
0 50 100 150 200 250 Q300
[m3/h]
0 10 20 30 40 50 60 70 80 Q [l/s]
55
ESH SERIES
0 200 400 600 800 1000gpm]

Q [Imp
0 200 400 600 800 1000 Q1200

[US gpm]
120
70 [%]
73
76 350
77
78.0
100
77
76 300
80.0 73
80
80-250/750 250
79.5
78 270
80-250/550
60 252 200
78
H [ft]
H[m]
80-250/450
237
150
40
100
20
50
0 0
8
80-250/750 20
6
270
NPSH [ft]
NPSH[m]
4
10
2
0 0
80
80-250/750 100
270
60 80
80-250/550
252
60
Pp[kW]
40 80-250/450
PP[HP]
237
40
20
20
ESH80-250_2P50_A_CH
0 0
0 40 80 120 160 200 240 Q280
[m3/h]
0 10 20 30 40 50 60 70 Q [l/s]
56
ESH SERIES
0 5 10 15 20 25 30 35 40 Q [Imp gpm]
0 10 20 30 40 Q [US gpm] 50
6
18
5 48 50
52
54 16
56
58 [%]
14
4 60.8
12
3 58.5 58 10
56
H [ft]
H[m]
54
8
25-125/02
2
128 6
4
1 25-125/02A
114
2
0 0
1.0
3
25-125/02
NPSH [ft]
NPSH[m]
128 2
0.5
1
0.0 0
0.2
0.2
25-125/02
Pp[kW]
128
0.1
PP[HP]
25-125/02A 0.1
114
ESH25-125_4P50_A_CH
0.0 0.0
0 2 4 6 8 10 Q12
[m3/h]
0.0 0.5 1.0 1.5 2.0 2.5 3.0 Q [l/s]
57
ESH SERIES
0 10 20 30 40 50 gpm]
Q [Imp
0 10 20 30 40 50 Q60
[US gpm]
10
9 30
8
53 54 [%] 25
55 56
7 57 58
6 59.4 20
5 58
57.4 57
56
H [ft]
15
H[m]
55
54
4 53
25-160/02
3 160 10
25-160/02A
2
145
5
1
0 0
1.0
3
NPSH [ft]
NPSH[m]
2
0.5
1
25-160/02
160
0.0 0
0.4
0.5
0.3 0.4
0.3
Pp[kW]
25-160/02
0.2
PP[HP]
160
25-160/02A 0.2
145
0.1
0.1
ESH25-160_4P50_A_CH
0.0 0.0
0 2 4 6 8 10 12 Q14
[m3/h]
0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 Q [l/s]
58
ESH SERIES
0 10 20 30 40 50 Q [Imp gpm]
0 10 20 30 40 50 60 70 gpm]
Q [US
14
45
12 42 40
44
46 [%]
48
50 35
51
10
52.2 30
8 51
50 25
48
50.4
H [ft]
H[m]
46
6 20
44
42
25-200/05 15
4 199
10
25-200/03
2 182
5
0 0
2.0
6
1.6
NPSH [ft]
NPSH[m]
1.2 4
0.8
25-200/05 2
0.4 199
0.0 0
0.5
0.6
25-200/05
0.4 199
0.5
0.3 25-200/03 0.4

Pp[kW]
182
PP[HP]
0.3
0.2
0.2
0.1
0.1
ESH25-200_4P50_A_CH
0.0 0.0
0 2 4 6 8 10 12 14 Q16
[m3/h]
0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 Q [l/s]
59
ESH SERIES
0 10 20 30 40 50 60 Q [Imp gpm]
0 10 20 30 40 50 60 70 Q [US gpm]
22
70
20 38 40
42
44
18
46
[%] 60
48.5
16 49.7
50
14 48.4
12 25-250/15
40
46.8
245
46
H [ft]
10
H[m]
25-250/11 30
8 228
25-250/07
6 208
20
4
10
2
0 0
5
15
4
NPSH [ft]
NPSH[m]
3 10
2 25-250/15
245 5
1
0 0
1.4
1.2
25-250/15 1.5
1.0 245
25-250/11
0.8
Pp[kW]
228 1.0
PP[HP]
0.6 25-250/07
208
0.4 0.5
0.2
ESH25-250_4P50_A_CH
0.0 0.0
0 2 4 6 8 10 12 14 16 Q18
[m3/h]
0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 Q [l/s]
5.0
60
ESH SERIES
0 10 20 30 40 50 gpm]
Q [Imp
0 10 20 30 40 50 Q60
[US gpm]
6
18
48 50
5 52 54
56
16
59
[%]
14
4 62.3
12
3 59.9 59 10
H [ft]
56
H[m]
54
52 8
50
2 48
6
32-125/02
128 4
1
32-125/02A
114 2
0 0
1.0
3
0.8
NPSH [ft]
NPSH[m]
0.6 2
0.4
32-125/02 1
0.2 128
0.0 0
0.2
0.2
Pp[kW]
PP[HP]
32-125/02
128
0.1
32-125/02A
114
0.1
ESH32-160_4P50_A_CH
0.0 0.0
0 2 4 6 8 10 12 Q14
[m3/h]
0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 Q [l/s]
61
ESH SERIES
0 10 20 30 40 50 Q [Imp gpm]
0 10 20 30 40 50 60 70 gpm]
Q [US
10
9 30
8 45 47.5
50
52.5 25
55 [%]
57.5
7
60.0
6 20
5 58.0 57.5
H [ft]
55 15
H[m]
52.5
4 50
47.5
3 45 10
2 32-160/02A
145 32-160/02 5
160
1
0 0
2
6
NPSH [ft]
NPSH[m]
4
1
32-160/02
160 2
0 0
0.4
0.5
0.3 0.4
0.3
Pp[kW]
0.2 32-160/02
PP[HP]
160
32-160/02A 0.2
145
0.1
0.1
ESH32-160_4P50_A_CH
0.0 0.0
0 2 4 6 8 10 12 14 Q16
[m3/h]
0 1 1 2 2 3 3 4 4 Q [l/s]
62
ESH SERIES
0 10 20 30 40 50 Q [Imp gpm]
0 10 20 30 40 50 60 70 gpm]
Q [US
14
45
37.5
12 40 40
42.5
45 [%]
47.5
50 35
10
51.6
30
8 50
25
47.5
49.9
H [ft]
45
H[m]
6 42.5 20
40
37.5
15
4
32-200/05
199 10
32-200/03
2 182
5
0 0
2.0
6
1.6
NPSH [ft]
NPSH[m]
1.2 4
32-200/05
0.8 199
2
0.4
0.0 0
0.5
32-200/05
0.6
0.4 199
0.5
0.3 32-200/03 0.4

Pp[kW]
182
PP[HP]
0.3
0.2
0.2
0.1
0.1
ESH32-200_4P50_A_CH
0.0 0.0
0 2 4 6 8 10 12 14 Q16
[m3/h]
0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 Q [l/s]
63
ESH SERIES
0 10 20 30 40 50 60 Q [Imp gpm]
0 10 20 30 40 50 60 70 Q [US gpm]
22
70
20 31.5 34
36.5 39
41.5
18 44
[%] 60
16 47.0
50
14 45.6
44
12 40
43.9
32-250/15
H [ft]
10
H[m]
245
30
8 32-250/11
228
6 20
32-250/07
208
4
10
2
0 0
5
15
4
NPSH [ft]
NPSH[m]
3 10
2 32-250/15
245 5
1
0 0
1.4
1.2 32-250/15 1.5

245
1.0
32-250/11
0.8 228
Pp[kW]
1.0
PP[HP]
32-250/07
0.6 208
0.4 0.5
0.2
ESH32-250_4P50_A_CH
0.0 0.0
0 2 4 6 8 10 12 14 16 Q18
[m3/h]
0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 Q [l/s]
5.0
64
ESH SERIES
0 10 20 30 40 50 60 70 80 90 gpm]
Q [Imp
0 20 40 60 80 100 Q [US gpm]

6
18
57
59
5 61
63 [%] 16
65
67
14
4 68.2
12
66.2
65
3 63
10
H [ft]
H[m]
61
59
8
57
2
6
40-125/02
135 4
1 40-125/02A
122
2
0 0
1.0
3
0.8
NPSH [ft]
NPSH[m]
0.6 40-125/02 2
135
0.4
1
0.2
0.0 0
0.3 0.4
0.3
0.2 40-125/02
135
Pp[kW]
0.2
PP[HP]
40-125/02A
122
0.1
0.1
ESH40-125_4P50_A_CH
0.0 0.0
0 5 10 15 20 Q25
[m3/h]
0 1 2 3 4 5 6 Q [l/s]
65
ESH SERIES
0 20 40 60 80 100 Q [Imp gpm]
0 20 40 60 80 100 120 Q [US gpm]

10
30
[%]
58
60
8 64
66
25
66.5
66
6 67.6 20
64
60
H [ft]
15
H[m]
58
40-160/05
4 171
40-160/03
40-160/03
159 10
159
2
5
0 0
3
40-160/05 8
2 171
NPSH [ft]
NPSH[m]
6
4
1
2
0 0
0.6 0.8
0.5 40-160/05
171
0.6
0.4 40-160/03
159
Pp[kW]
0.3 0.4
PP[HP]
0.2
0.2
0.1
ESH40-160_4P50_A_CH
0.0 0.0
0 5 10 15 20 25 Q30
[m3/h]
0 1 2 3 4 5 6 7 8 Q [l/s]
66
ESH SERIES
0 20 40 60 80 100 Q [Imp gpm]
0 20 40 60 80 100 120 Q [US gpm]

15
14 [%]
45
55
13 58
60
12 62 40
62.9
11
35
10 62
63
9 60 30
64.3 58
8
63 40-200/11 25
7 209
H [ft]
H[m]
6 40-200/07 20
190
5
15
4
3 10
2
5
1
0 0
3
40-200/11 8
2 209
NPSH [ft]
NPSH[m]
6
4
1
2
0 0
1.0
40-200/11
209 1.2
0.8
40-200/07
1.0
190
0.6 0.8
Pp[kW]
PP[HP]
0.6
0.4
0.4
0.2
0.2
ESH40-200_4P50_A_CH
0.0 0.0
0 5 10 15 20 25 Q30
[m3/h]
0 1 2 3 4 5 6 7 8 Q [l/s]
67
ESH SERIES
0 20 40 60 80 100 Q [Imp gpm]
0 20 40 60 80 100 120 Q [US gpm]

22
45 70
50 [%]
20 53
55
18 57 60
58.1
16
57 50
57.0
14 40-250/22
251
55.8 55
12 40-250/15
40
233
H [ft]
10
H[m]
40-250/11
218 30
8
6 20
4
10
2
0 0
8
40-250/11 40-250/22
218 251
6 20
NPSH [ft]
NPSH[m]
4
10
2
0 0
2.0
40-250/22
2.5
251
1.5 40-250/15 2.0
233
40-250/11
1.5
Pp[kW]
1.0 218
PP[HP]
1.0
0.5
0.5
ESH40-250_4P50_A_CH
0.0 0.0
0 5 10 15 20 25 Q30
[m3/h]
0 1 2 3 4 5 6 7 8 Q [l/s]
68
ESH SERIES
0 20 40 60 80 100 120 140 160 180 gpm]

Q [Imp
0 50 100 150 200 Q [US gpm]

6.5
6.0 60
20
62.5
65
67.5
5.5 70
72.5 [%]
5.0
4.5
75.1 15
4.0
73.2 72.5
3.5 70
71.5 67.5
10
H [ft]
3.0
H[m]
65
62.5
2.5 60
2.0 50-125/05
137
1.5 5
50-125/03
1.0 125
0.5 50-125/02
114
0.0 0
4
3 10
NPSH [ft]
NPSH[m]
2
50-125/05
137
5
1
0 0
0.6 0.8
0.5
0.6
0.4 50-125/05
137
Pp[kW]
0.3 0.4
PP[HP]
50-125/03
125
0.2 50-125/02
114 0.2
0.1
ESH50-125_4P50_A_CH
0.0 0.0
0 5 10 15 20 25 30 35 40 45 Q50
[m3/h]
0 2 4 6 8 10 12 Q [l/s]
69
ESH SERIES
0 20 40 60 80 100 120 140 160 180gpm]

Q [Imp
0 50 100 150 200 Q [US gpm]

10
30
[%]
9 65
68
69
70
71
8
73.0
25
7
71
6
71.3 70 20
69
68
5 65
H [ft]
15
H[m]
50-160/11
4
174
3 50-160/07 10
158
2
5
1
0 0
3 50-160/07
158 8
50-160/11
2 174
NPSH [ft]
NPSH[m]
6
4
1
2
0 0
1.0
1.2
0.8 50-160/11
174 1.0
0.6 50-160/07 0.8

Pp[kW]
158
PP[HP]
0.6
0.4
0.4
0.2
0.2
ESH50-160_4P50_A_CH
0.0 0.0
0 10 20 30 40 Q50
[m3/h]
0 2 4 6 8 10 12 Q [l/s]
70
ESH SERIES
0 20 40 60 80 100 120 140 160 180gpm]

Q [Imp
0 50 100 150 200 Q [US gpm]

15
55
14 60 [%]
45
63
13 66
68
12 40
70.1
11
35
10 69.1 68
9 30
66
8 63
25
60
7
H [ft]
H[m]
55
6 20
5 50-200/15
209 15
4
50-200/11
3 197 10
2
5
1
0 0
5
50-200/11 15
4 197
NPSH [ft]
NPSH[m]
3 50-200/15 10
209
2
5
1
0 0
1.5 2.0
50-200/15
209
1.5
1.0
50-200/11
Pp[kW]
197
1.0
PP[HP]
0.5
0.5
ESH50-200_4P50_A_CH
0.0 0.0
0 5 10 15 20 25 30 35 40 45 Q50
[m3/h]
0 2 4 6 8 10 12 Q [l/s]
71
ESH SERIES
0 20 40 60 80 100 120 140 160 180gpm]

Q [Imp
0 50 100 150 200 Q [US gpm]

25
80
[%]
55
60 70
63
20 66
67.9 60
15 69.0 66 50
68
70.0 50-250/30 40
H [ft]
H[m]
250
68
10 50-250/22
237 30
50-250/22A
224
20
5
10
0 0
6
50-250/22A
224
15
4
NPSH [ft]
NPSH[m]
50-250/30
250 10
2
5
0 0
3 4
50-250/30
250 3
2 50-250/22
Pp[kW]
237
2
PP[HP]
50-250/22A
224
1
1
ESH50-250_4P50_A_CH
0 0
0 10 20 30 40 Q50
[m3/h]
0 2 4 6 8 10 12 Q [l/s]
72
ESH SERIES
0 50 100 150 200 250 Q [Imp gpm]
0 50 100 150 200 250 300 350gpm]

Q [US
18
57.5 60 [%]
62.5 65
67.5
16 70
50
72.0
14
70
12 70.2
67.5
40
65
10 62.5
68.2
30
65-200/30
H [ft]
H[m]
8 219
6 65-200/22 20
199
4
65-200/15
176 10
2
0 0
7
6 20
5 65-200/30 15
NPSH [ft]
NPSH[m]
4 219
3 10
2
5
1
0 0
3.2
4
65-200/30
2.4 219
3
Pp[kW]
PP[HP]
65-200/22
1.6 199
2
65-200/15
176
0.8 1
ESH65-200_4P50_A_CH
0.0 0
0 10 20 30 40 50 60 70 Q80
[m3/h]
0 5 10 15 20 Q [l/s]
73
ESH SERIES
0 50 100 150 200 250 300 Q [Imp gpm]
0 50 100 150 200 250 300 350 Q [US gpm]

25
64
80
66
68 [%]
70
71.0 70
20
70
68
60
71.9
71 66
64
15 50
71
65-250/55
255
40
H [ft]
H[m]
65-250/40
10 240
30
20
5
10
0 0
6
65-250/40 65-250/55
240 255 15
4
NPSH [ft]
NPSH[m]
10
2
5
0 0
6 8
65-250/55
5
255
6
4 65-250/40
240
Pp[kW]
3 4
PP[HP]
2
2
1
ESH65-250_4P50_A_CH
0 0
0 10 20 30 40 50 60 70 80 Q90
[m3/h]
0 5 10 15 20 Q [l/s]
25
74
ESH SERIES
0 100 200 300 400 500 gpm]

Q [Imp
0 100 200 300 400 500 Q 600

[US gpm]
12
[%]
66
68
35
70
10 72
73.4 30
8 72
25
70
74.2 68
74
6 66 20
H [ft]
H[m]
75.2
74 15
4 80-160/22
186
10
80-160/22A
177
2 80-160/15
169x15 5
0 0
3
80-160/15 80-160/22
169x15 186 8
2
NPSH [ft]
NPSH[m]
6
4
1
2
0 0
2.5
3.0
80-160/22
2.0 186
2.5
80-160/22A
1.5 177 2.0
Pp[kW]
80-160/15
PP[HP]
169x15 1.5
1.0
1.0
0.5
0.5
ESH80-160_4P50_A_CH
0.0 0.0
0 20 40 60 80 100 120 Q140
[m3/h]
0 5 10 15 20 25 30 35 Q [l/s]
75
ESH SERIES
0 100 200 300 400 500 Q [Imp gpm]
0 100 200 300 400 500 600 700

Q [US gpm]
18
[%]
16 65
70
73
50
14 76
78
78.3
12 78 40
76
10 80.5
73
70 30
H [ft]
H[m]
8
65
6 80-200/40 20
220
4 80-200/30
198 10
2
0 0
8
6 20
80-200/30
NPSH [ft]
NPSH[m]
198
4 80-200/40
220 10
2
0 0
5
6
4 80-200/40
220 5
3 4
Pp[kW]
80-200/30
PP[HP]
198 3
2
2
1
1
ESH80-200_4P50_A_CH
0 0
0 20 40 60 80 100 120 140 Q160
[m3/h]
0 5 10 15 20 25 30 35 40 Q [l/s]
76
ESH SERIES
0 100 200 300 400 500 Q [Imp gpm]
0 100 200 300 400 500 600 700

Q [US gpm]
30
[%]
64 90
67
70
25 73
80
74.3
73
70
20
76.7 70 60
76 67
15 77.5 64 50
H [ft]
H[m]
76
80-250/110
270 40
10 80-250/75
252 30
80-250/55
237 20
5
10
0 0
8
6 20
NPSH [ft]
NPSH[m]
80-250/110
4 270
10
2
0 0
10
12
8 80-250/110
270 10
6 80-250/75 8
Pp[kW]
252
PP[HP]
80-250/55 6
4 237
4
2
2
ESH80-250_4P50_A_CH
0 0
0 20 40 60 80 100 120 140 Q160
[m3/h]
0 5 10 15 20 25 30 35 40 Q [l/s]
77
78
DIMENSIONS
AND WEIGHTS
79
ESHE SERIES
DIMENSIONS AND WEIGHTS AT 50 Hz, 2 POLES
80
ESHE SERIES
DIMENSIONI E PESI
DIMENSIONS AND SERIE ESHE 2 poli
WEIGHTS AT 5050 Hz
Hz, 2 POLES
PUMP TYPE DIMENSIONS (mm) WEIGHT
ESHE..2 PUMP SUPPORT B H L k

DNM DNA a h2 w w1 x b c *c1 h1 m m1 n n1 s max kg
25-125/07/S 25 50 80 140 - - 129 - - - 160 - - 190 130 - 218 300 443 98 18,6
25-125/11/S 25 50 80 140 - - 129 - - - 160 - - 190 130 - 218 300 443 98 20,6
25-160/15/S 25 50 80 160 - - 129 - - - 160 - - 210 130 - 253 320 443 98 24,4
25-160/22/P 25 50 80 160 - - 134 - - - 160 - - 210 130 - 253 320 478 98 29
25-200/30/P 25 50 80 180 - - 134 - - - 160 - - 230 130 - 284 340 478 98 38
25-200/40/P 25 50 80 180 - - 154 - - - 160 - - 230 130 - 284 340 499 98 41
25-250/55/P 25 50 100 225 - - 168 - - - 180 - - 265 130 - 345 405 553 98 66
25-250/75/P 25 50 100 225 - 305 191 - - - 180 - - 265 130 - 345 405 567 98 84
25-250/110/P 25 50 100 225 - 343 191 - - - 180 - - 265 130 - 345 405 605 98 92
32-125/07/S 32 50 80 140 - - 129 - - - 112 - - 190 130 - 218 252 443 98 18,6
32-125/11/S 32 50 80 140 - - 129 - - - 112 - - 190 130 - 218 252 443 98 20,6
32-160/15/S 32 50 80 160 - - 129 - - - 132 - - 210 130 - 253 292 443 98 24,4
32-160/22/P 32 50 80 160 - - 134 - - - 132 - - 210 130 - 253 292 478 98 29
32-200/30/P 32 50 80 180 - - 134 - - - 160 - - 230 130 - 284 340 478 98 38
32-200/40/P 32 50 80 180 - - 154 - - - 160 - - 230 130 - 284 340 499 98 41
32-250/55/P 32 50 100 225 - - 168 - - - 180 - - 265 130 - 345 405 553 98 66
32-250/75/P 32 50 100 225 - 305 191 - - - 180 - - 265 130 - 345 405 567 98 84
32-250/110/P 32 50 100 225 - 343 191 - - - 180 - - 265 130 - 345 405 605 98 92
40-125/11/S 40 65 80 140 - - 129 - - - 112 - - 190 130 - 218 252 443 100 21,6
40-125/15/S 40 65 80 140 - - 129 - - - 112 - - 190 130 - 218 252 443 100 22,4
40-125/22/P 40 65 80 140 - - 134 - - - 112 - - 190 130 - 218 252 478 100 30
40-160/30/P 40 65 80 160 - - 134 - - - 132 - - 210 130 - 253 292 478 100 32
40-160/40/P 40 65 80 160 - - 154 - - - 132 - - 210 130 - 253 292 499 100 40
40-200/55/P 40 65 100 180 - - 168 - - - 160 - - 230 130 - 284 340 553 100 52
40-200/75/P 40 65 100 180 - 305 191 - - - 160 - - 230 130 - 284 340 567 100 65
40-250/92/P 40 65 100 225 - 343 191 - - - 180 - - 265 130 - 345 405 605 107 89
40-250/110/P 40 65 100 225 - 343 191 - - - 180 - - 265 130 - 345 405 605 107 94
40-250/150/P 40 65 100 225 208 - 240 49 5 20 180 304 210 304 254 15 345 420 694 107 130
50-125/22/P 50 65 100 160 - - 134 - - - 132 - - 210 130 - 253 292 498 104 30
50-125/30/P 50 65 100 160 - - 134 - - - 132 - - 210 130 - 253 292 498 104 33
50-125/40/P 50 65 100 160 - - 154 - - - 132 - - 210 130 - 253 292 519 104 40
50-160/55/P 50 65 100 180 - - 168 - - - 160 - - 210 130 - 253 340 553 104 52
50-160/75/P 50 65 100 180 - 305 191 - - - 160 - - 210 130 - 253 351 567 104 67
50-200/92/P 50 65 100 200 - 343 191 - - - 160 - - 245 130 - 310 360 605 104 84
50-200/110/P 50 65 100 200 - 343 191 - - - 160 - - 245 130 - 310 360 605 104 88
50-250/150/P 50 65 100 225 208 - 240 49 5 20 180 304 210 304 254 15 345 420 694 107 131
50-250/185/P 50 65 100 225 208 - 240 49 5 20 180 304 254 304 254 15 345 420 694 107 144
50-250/220/P 50 65 100 225 208 - 240 49 5 20 180 304 254 304 254 15 345 420 694 107 147
65-160/40/P 65 80 100 200 - - 154 - - - 160 - - 245 130 - 310 360 519 130 56
65-160/55/P 65 80 100 200 - - 168 - - - 160 - - 245 130 - 310 360 553 130 63
65-160/75/P 65 80 100 200 - 305 191 - - - 160 - - 245 130 - 310 360 567 130 80
65-160/92/P 65 80 100 200 - 343 191 - - - 160 - - 245 130 - 310 360 605 130 95
65-160/110/P 65 80 100 200 - 343 191 - - - 160 - - 245 130 - 310 360 605 130 102
65-200/150/P 65 80 100 225 208 - 240 49 5 20 180 304 210 304 254 15 310 420 694 130 131
65-200/185/P 65 80 100 225 208 - 240 49 5 20 180 304 254 304 254 15 310 420 694 130 141
65-200/220/P 65 80 100 225 208 - 240 49 5 20 180 304 254 304 254 15 310 420 694 130 151
80-160/110/P 80 100 125 225 - 343 191 - - - 180 - - 265 130 - 345 405 630 160 94
80-160/150/P 80 100 125 225 208 - 240 49 5 20 180 304 210 304 254 15 345 420 719 160 128
80-160/185/P 80 100 125 225 208 - 240 49 5 20 180 304 254 304 254 15 345 420 719 160 139
80-200/220/P 80 100 125 250 208 - 240 49 5 20 180 304 254 304 254 15 345 430 719 160 156
* Motor shim on request ESHE_2p50-en_a_td
81
ESHE SERIES
82
ESHE SERIES
DIMENSIONI E PESI
DIMENSIONS AND SERIE ESHE 4 poli
WEIGHTS AT 5050 Hz
Hz, 4 POLES
ESHE..4 PUMP SUPPORT B H L k

DNM DNA a h2 w w1 x b c *c1 h1 m m1 n n1 s max kg
25-125/02A/S 25 50 80 140 - - 121 - - - 160 - - 190 130 - 218 300 411 98 15
25-125/02/S 25 50 80 140 - - 121 - - - 160 - - 190 130 - 218 300 411 98 16
25-160/02A/S 25 50 80 160 - - 121 - - - 160 - - 210 130 - 253 320 411 98 18
25-160/02/S 25 50 80 160 - - 121 - - - 160 - - 210 130 - 253 320 411 98 19
25-200/03/S 25 50 80 180 - - 121 - - - 160 - - 230 130 - 284 340 411 98 26
25-200/05/S 25 50 80 180 - - 129 - - - 160 - - 230 130 - 284 340 443 98 27
25-250/07/X 25 50 100 225 - - 128 - - - 180 - - 265 130 - 345 405 431 98 42
25-250/11/P 25 50 100 225 - - 134 - - - 180 - - 265 130 - 345 405 498 98 49
25-250/15/P 25 50 100 225 - - 134 - - - 180 - - 265 130 - 345 405 498 98 51
32-125/02A/S 32 50 80 140 - - 121 - - - 112 - - 190 130 - 218 252 411 98 15
32-125/02/S 32 50 80 140 - - 121 - - - 112 - - 190 130 - 218 252 411 98 16
32-160/02A/S 32 50 80 160 - - 121 - - - 132 - - 210 130 - 253 292 411 98 18
32-160/02/S 32 50 80 160 - - 121 - - - 132 - - 210 130 - 253 292 411 98 19
32-200/03/S 32 50 80 180 - - 121 - - - 160 - - 230 130 - 284 340 411 98 26
32-200/05/S 32 50 80 180 - - 129 - - - 160 - - 230 130 - 284 340 443 98 27
32-250/07/X 32 50 100 225 - - 128 - - - 180 - - 265 130 - 345 405 431 98 42
32-250/11/P 32 50 100 225 - - 134 - - - 180 - - 265 130 - 345 405 498 98 49
32-250/15/P 32 50 100 225 - - 134 - - - 180 - - 265 130 - 345 405 498 98 51
40-125/02A/S 40 65 80 140 - - 121 - - - 112 - - 190 130 - 218 252 411 100 16
40-125/02/S 40 65 80 140 - - 121 - - - 112 - - 190 130 - 218 252 411 100 17
40-160/03/S 40 65 80 160 - - 121 - - - 132 - - 210 130 - 253 292 411 100 20
40-160/05/S 40 65 80 160 - - 129 - - - 132 - - 210 130 - 253 292 443 100 24
40-200/07/X 40 65 100 180 - - 128 - - - 160 - - 230 130 - 285 340 431 100 27
40-200/11/P 40 65 100 180 - - 134 - - - 160 - - 230 130 - 285 340 498 100 35
40-250/11/P 40 65 100 225 - - 134 - - - 180 - - 265 130 - 345 405 498 107 47
40-250/15/P 40 65 100 225 - - 134 - - - 180 - - 265 130 - 345 405 498 107 61
40-250/22/P 40 65 100 225 - - 168 - - - 180 - - 265 130 - 345 405 522 107 65
50-125/02/S 50 65 100 160 - - 121 - - - 132 - - 210 130 - 253 292 431 104 20
50-125/03/S 50 65 100 160 - - 121 - - - 132 - - 210 130 - 253 292 431 104 20
50-125/05/S 50 65 100 160 - - 129 - - - 132 - - 210 130 - 253 292 463 104 26
50-160/07/X 50 65 100 180 - - 128 - - - 160 - - 210 130 - 253 340 431 104 30
50-160/11/P 50 65 100 180 - - 134 - - - 160 - - 210 130 - 253 340 498 104 40
50-200/11/P 50 65 100 200 - - 134 - - - 160 - - 245 130 - 310 360 498 104 48
50-200/15/P 50 65 100 200 - - 134 - - - 160 - - 245 130 - 310 360 498 104 51
50-250/22A/P 50 65 100 225 - - 168 - - - 180 - - 265 130 - 345 405 522 107 56
50-250/22/P 50 65 100 225 - - 168 - - - 180 - - 265 130 - 345 405 522 107 56
50-250/30/P 50 65 100 225 - - 168 - - - 180 - - 265 130 - 345 405 553 107 62
65-200/15/P 65 80 100 225 - - 134 - - - 180 - - 245 130 - 310 405 498 130 56
65-200/22/P 65 80 100 225 - - 168 - - - 180 - - 245 130 - 310 405 522 130 64
65-200/30/P 65 80 100 225 - - 168 - - - 180 - - 245 130 - 310 405 553 130 64
65-250/40/P 65 80 100 250 - 315 168 - - - 200 - - 265 130 - 345 450 598 140 84
65-250/55/P 65 80 100 250 - 343 191 - - - 200 - - 265 130 - 345 450 605 140 97
80-160/15/P 80 100 125 225 - - 134 - - - 180 - - 265 130 - 345 405 523 160 55
80-160/22A/P 80 100 125 225 - - 168 - - - 180 - - 265 130 - 345 405 547 160 63
80-160/22/P 80 100 125 225 - - 168 - - - 180 - - 265 130 - 345 405 547 160 66
80-200/30/P 80 100 125 250 - - 168 - - - 180 - - 265 130 - 345 430 578 160 69
80-200/40/P 80 100 125 250 - 315 168 - - - 180 - - 265 130 - 345 430 623 160 88
80-250/55/P 80 100 125 280 - 343 191 - - - 200 - - 303 210 - 383 480 630 160 102
80-250/75/P 80 100 125 280 - 343 191 - - - 200 - - 303 210 - 383 480 630 160 106
80-250/110/P 80 100 125 280 208 - 240 49 5 40 200 304 210 304 254 15 383 480 719 160 145
* Motor shim on request ESHE_4p50-en_a_td
83
ESHS SERIES
84
ESHS SERIES
DIMENSIONI E PESI
DIMENSIONS AND SERIE ESHS 2 poli
WEIGHTS AT 50
50Hz
Hz, 2 POLES
ESHS..2 PUMP SUPPORT B H L k

DNM DNA a f h2 w w1 x b c *c1 h1 m m1 n n1 s max kg
25-125/07/S 25 50 80 155 140 - - 129 - - - 160 - - 190 130 - 218 300 498 98 24
25-125/11/S 25 50 80 155 140 - - 129 - - - 160 - - 190 130 - 218 300 498 98 25
25-160/15/S 25 50 80 155 160 - - 129 - - - 160 - - 210 130 - 253 320 498 98 27
25-160/22/P 25 50 80 155 160 - - 134 - - - 160 - - 210 130 - 253 320 533 98 33
25-200/30/P 25 50 80 165 180 - - 134 - - - 160 - - 230 130 - 284 340 543 98 44
25-200/40/P 25 50 80 165 180 - - 154 - - - 160 - - 230 130 - 284 340 564 98 51
25-250/55/P 25 50 100 192 225 - 399 168 - - - 180 - - 265 130 - 345 405 667 98 77
25-250/75/P 25 50 100 192 225 - 397 191 - - - 180 - - 265 130 - 345 405 659 98 91
25-250/110/P 25 50 100 222 225 330 - 240 49 5 20 180 304 210 304 254 15 350 420 816 98 130
32-125/07/S 32 50 80 155 140 - - 129 - - - 112 - - 190 130 - 218 252 498 98 24
32-125/11/S 32 50 80 155 140 - - 129 - - - 112 - - 190 130 - 218 252 498 98 25
32-160/15/S 32 50 80 155 160 - - 129 - - - 132 - - 210 130 - 253 292 498 98 27
32-160/22/P 32 50 80 155 160 - - 134 - - - 132 - - 210 130 - 253 292 533 98 33
32-200/30/P 32 50 80 165 180 - - 134 - - - 160 - - 230 130 - 284 340 543 98 44
32-200/40/P 32 50 80 165 180 - - 154 - - - 160 - - 230 130 - 284 340 564 98 51
32-250/55/P 32 50 100 192 225 - 399 168 - - - 180 - - 265 130 - 345 405 667 98 77
32-250/75/P 32 50 100 192 225 - 397 191 - - - 180 - - 265 130 - 345 405 659 98 91
32-250/110/P 32 50 100 222 225 330 - 240 49 5 20 180 304 210 304 254 15 350 420 816 98 130
40-125/11/S 40 65 80 155 140 - - 129 - - - 112 - - 190 130 - 218 252 498 100 26
40-125/15/S 40 65 80 155 140 - - 129 - - - 112 - - 190 130 - 218 252 498 100 26
40-125/22/P 40 65 80 155 140 - - 134 - - - 112 - - 190 130 - 218 252 533 100 32
40-160/30/P 40 65 80 165 160 - - 134 - - - 132 - - 210 130 - 253 292 543 100 42
40-160/40/P 40 65 80 165 160 - - 154 - - - 132 - - 210 130 - 253 292 564 100 48
40-200/55/P 40 65 100 192 180 - 399 168 - - - 160 - - 230 130 - 300 340 667 100 63
40-200/75/P 40 65 100 192 180 - 397 191 - - - 160 - - 230 130 - 300 351 659 100 80
40-250/110A/P 40 65 100 222 225 330 - 240 49 5 20 180 304 210 304 254 15 350 420 816 107 129
40-250/110/P 40 65 100 222 225 330 - 240 49 5 20 180 304 210 304 254 15 350 420 816 107 129
40-250/150/P 40 65 100 222 225 330 - 240 49 5 20 180 304 210 304 254 15 350 420 816 107 142
50-125/22/P 50 65 100 155 160 - - 134 - - - 132 - - 210 130 - 253 292 553 104 36
50-125/30/P 50 65 100 165 160 - - 134 - - - 132 - - 210 130 - 253 292 563 104 37
50-125/40/P 50 65 100 165 160 - - 154 - - - 132 - - 210 130 - 253 292 584 104 48
50-160/55/P 50 65 100 192 180 - 399 168 - - - 160 - - 210 130 - 300 340 667 104 62
50-160/75/P 50 65 100 192 180 - 397 191 - - - 160 - - 210 130 - 300 351 659 104 81
50-200/110A/P 50 65 100 222 200 330 - 240 49 5 20 180 304 210 304 254 15 350 420 816 104 126
50-200/110/P 50 65 100 222 200 330 - 240 49 5 20 180 304 210 304 254 15 350 420 816 104 130
50-250/150/P 50 65 100 222 225 330 - 240 49 5 20 180 304 210 304 254 15 350 420 816 107 148
50-250/185/P 50 65 100 222 225 330 - 240 49 5 20 180 304 254 304 254 15 350 420 816 107 156
50-250/220/P 50 65 100 222 225 330 - 240 49 5 20 180 304 254 304 254 15 350 420 816 107 162
65-160/40/P 65 80 100 165 200 - - 154 - - - 160 - - 245 130 - 310 360 584 130 60
65-160/55/P 65 80 100 192 200 - 399 168 - - - 160 - - 245 130 - 310 360 667 130 78
65-160/75/P 65 80 100 192 200 - 397 191 - - - 160 - - 245 130 - 310 360 659 130 93
65-160/110A/P 65 80 100 222 200 330 - 240 49 5 20 180 304 210 304 254 15 350 420 816 130 116
65-160/110/P 65 80 100 222 200 330 - 240 49 5 20 180 304 210 304 254 15 350 420 816 130 120
65-200/150/P 65 80 100 222 225 330 - 240 49 5 20 180 304 210 304 254 15 350 420 816 130 147
65-200/185/P 65 80 100 222 225 330 - 240 49 5 20 180 304 254 304 254 15 350 420 816 130 153
65-200/220/P 65 80 100 222 225 330 - 240 49 5 20 180 304 254 304 254 15 350 420 816 130 167
65-250/300/W 65 80 100 228 250 361 - 317 82 30 - 200 370 305 385 318 18 402 517 985 140 290
65-250/370/W 65 80 100 228 250 361 - 317 82 30 - 200 370 305 385 318 18 402 517 985 140 322
80-160/110/P 80 100 125 222 225 330 - 240 49 5 20 180 304 210 304 254 15 350 420 841 160 116
80-160/150/P 80 100 125 222 225 330 - 240 49 5 20 180 304 210 304 254 15 350 420 841 160 152
80-160/185/P 80 100 125 222 225 330 - 240 49 5 20 180 304 254 304 254 15 350 420 841 160 160
80-200/220/P 80 100 125 222 250 330 - 240 49 5 20 180 304 254 304 254 15 350 430 841 160 162
80-200/300/W 80 100 125 228 250 361 - 317 82 30 - 200 370 305 385 318 18 402 517 985 160 312
80-200/370/W 80 100 125 228 250 361 - 317 82 30 - 200 370 305 385 318 18 402 517 985 160 317
* Motor shim on request ESHS_2p50-en_a_td
85
ESHS SERIES
86
ESHS SERIES
DIMENSIONI E PESI
DIMENSIONS AND SERIE ESHS 4 poli
WEIGHTS AT 50
50Hz
Hz, 4 POLES
ESHS..4 PUMP SUPPORT B H L k

DNM DNA a f h2 w w1 x b c *c1 h1 m m1 n n1 s max kg
25-250/07/X 25 50 100 155 225 - - 128 - - - 180 - - 265 130 - 345 405 486 98 42
25-250/11/P 25 50 100 155 225 - - 134 - - - 180 - - 265 130 - 345 405 553 98 49
25-250/15/P 25 50 100 155 225 - - 134 - - - 180 - - 265 130 - 345 405 553 98 50
32-250/07/X 32 50 100 155 225 - - 128 - - - 180 - - 265 130 - 345 405 486 98 42
32-250/11/P 32 50 100 155 225 - - 134 - - - 180 - - 265 130 - 345 405 553 98 49
32-250/15/P 32 50 100 155 225 - - 134 - - - 180 - - 265 130 - 345 405 553 98 50
40-200/07/X 40 65 100 155 180 - - 128 - - - 160 - - 230 130 - 284 340 486 ## 31
40-200/11/P 40 65 100 155 180 - - 134 - - - 160 - - 230 130 - 284 340 553 ## 37
40-250/11/P 40 65 100 155 225 - - 134 - - - 180 - - 265 130 - 345 405 553 ## 51
40-250/15/P 40 65 100 155 225 - - 134 - - - 180 - - 265 130 - 345 405 553 ## 64
40-250/22/P 40 65 100 165 225 - - 168 - - - 180 - - 265 130 - 345 405 587 ## 68
50-160/07/X 50 65 100 155 180 - - 128 - - - 160 - - 210 130 - 253 340 486 ## 30
50-160/11/P 50 65 100 155 180 - - 134 - - - 160 - - 210 130 - 253 340 553 ## 36
50-200/11/P 50 65 100 155 200 - - 134 - - - 160 - - 245 130 - 310 360 553 ## 49
50-200/15/P 50 65 100 155 200 - - 134 - - - 160 - - 245 130 - 310 360 553 ## 52
50-250/22A/P 50 65 100 165 225 - - 168 - - - 180 - - 265 130 - 345 405 587 ## 58
50-250/22/P 50 65 100 165 225 - - 168 - - - 180 - - 265 130 - 345 405 587 ## 59
50-250/30/P 50 65 100 165 225 - - 168 - - - 180 - - 265 130 - 345 405 618 ## 65
65-200/15/P 65 80 100 155 225 - - 134 - - - 180 - - 245 130 - 310 405 553 ## 54
65-200/22/P 65 80 100 165 225 - - 168 - - - 180 - - 245 130 - 310 405 587 ## 71
65-200/30/P 65 80 100 165 225 - - 168 - - - 180 - - 245 130 - 310 405 618 ## 72
65-250/40/P 65 80 100 165 250 - 380 168 - - - 200 - - 265 130 - 345 450 663 ## 97
65-250/55/P 65 80 100 192 250 - 435 191 - - - 200 - - 265 130 - 345 450 697 ## 104
80-160/15/P 80 100 125 155 225 - - 134 - - - 180 - - 265 130 - 345 405 578 ## 59
80-160/22A/P 80 100 125 165 225 - - 168 - - - 180 - - 265 130 - 345 405 612 ## 67
80-160/22/P 80 100 125 165 225 - - 168 - - - 180 - - 265 130 - 345 405 612 ## 67
80-200/30/P 80 100 125 165 250 - - 168 - - - 180 - - 265 130 - 345 430 643 ## 72
80-200/40/P 80 100 125 165 250 - 380 168 - - - 180 - - 265 130 - 345 430 688 ## 88
80-250/55/P 80 100 125 192 280 - 435 191 - - - 200 - - 303 210 - 383 480 722 ## 107
80-250/75/P 80 100 125 192 280 - 435 191 - - - 200 - - 303 210 - 383 480 722 ## 113
80-250/110/P 80 100 125 222 280 330 - 240 49 5 40 200 ## 210 304 254 15 383 480 841 ## 153
* Motor shim on request ESHS_4p50-en_a_td
87
ESH SERIES
DIMENSIONS AND WEIGHTS (BARE SHAFT)
88
ESH SERIES
DIMENSIONI E PESI
DIMENSIONS AND SERIE ESH (bare(BARE
WEIGHTS shaft) SHAFT)
ESH PUMP SUPPORT SHAFT B k

(BARE SHAFT) DNM DNA a f h1 h2 b c m m1 n n1 s w d l t u kg
25-125 25 50 80 360 112 140 47 3 100 70 190 140 14 260 24 50 27 8 218 98 14
25-160 25 50 80 360 132 160 48 3 100 70 240 190 14 260 24 50 27 8 253 98 17
25-200 25 50 80 360 160 180 47 3 100 70 240 190 14 260 24 50 27 8 284 98 20
25-250 25 50 100 360 180 225 54 6 125 95 320 250 14 260 24 50 27 8 345 98 34
32-125 32 50 80 360 112 140 47 3 100 70 190 140 14 260 24 50 27 8 218 98 14
32-160 32 50 80 360 132 160 48 3 100 70 240 190 14 260 24 50 27 8 253 98 17
32-200 32 50 80 360 160 180 47 3 100 70 240 190 14 260 24 50 27 8 284 98 20
32-250 32 50 100 360 180 225 54 6 125 95 320 250 14 260 24 50 27 8 345 98 34
40-125 40 65 80 360 112 140 47 3 100 70 210 160 14 260 24 50 27 8 218 100 16
40-160 40 65 80 360 132 160 48 3 100 70 240 190 14 260 24 50 27 8 253 100 18
40-200 40 65 100 360 160 180 50 3 100 70 265 212 14 260 24 50 27 8 284 100 20
40-250 40 65 100 360 180 225 54 6 125 95 320 250 14 260 24 50 27 8 345 107 33
50-125 50 65 100 360 132 160 48 3 100 70 240 190 14 260 24 50 27 8 253 104 17
50-160 50 65 100 360 160 180 48 3 100 70 265 212 14 260 24 50 27 8 253 104 24
50-200 50 65 100 360 160 200 40 6 100 70 265 212 14 260 24 50 27 8 310 104 30
50-250 50 65 100 360 180 225 54 6 125 95 320 250 14 260 24 50 27 8 345 107 37
65-160 65 80 100 360 160 200 48 6 125 95 280 212 14 260 24 50 27 8 310 130 31
65-200 65 80 100 360 180 225 65 15 125 95 320 250 14 260 24 50 27 8 310 130 42
65-250 65 80 100 470 200 250 80 18 160 120 360 280 18 340 32 80 35 10 345 140 55
80-160 80 100 125 360 180 225 54 6 125 95 320 250 14 260 24 50 27 8 345 160 37
80-200 80 100 125 470 180 250 65 15 125 95 345 280 14 340 32 80 35 10 345 160 55
80-250 80 100 125 470 200 280 80 18 160 120 400 315 18 340 32 80 35 10 383 160 67
ESHbs-en_a_td
89
ESHF SERIES
90
ESHF SERIES
DIMENSIONI E PESI
DIMENSIONS AND SERIE ESHF 2 poli
WEIGHTS AT 50
50Hz
Hz, 2 POLES
PUMP TYPE DIMENSIONS (mm) s WEIGHT COUPLING
ESHF..2 FOR TYPE
DNM DNA a B1 B2 L1 L2 L3 G M h1 h2 Hmax SCREWS kg

25-125/07/S 25 50 80 320 360 746 540 800 130 60 212 140 352 M16 67 A2
25-125/11/S 25 50 80 320 360 746 540 800 130 60 212 140 352 M16 69 A2
25-160/15/P 25 50 80 350 390 791 600 900 150 60 232 160 392 M16 73 A3
25-160/22/P 25 50 80 350 390 791 600 900 150 60 232 160 392 M16 75 A3
25-200/30/P 25 50 80 350 390 822 600 900 150 60 260 180 440 M16 95 B1
25-200/40/P 25 50 80 350 390 825 600 900 150 60 260 180 440 M16 97 B1
25-250/55/P 25 50 100 440 490 910 740 1120 190 75 280 225 505 M20 130 C1
25-250/75/P 25 50 100 440 490 910 740 1120 190 75 280 225 505 M20 134 C1
25-250/110/P 25 50 100 490 540 1067 840 1250 205 75 280 225 520 M20 181 C2
32-125/07/S 32 50 80 320 360 746 540 800 130 60 212 140 352 M16 67 A2
32-125/11/S 32 50 80 320 360 746 540 800 130 60 212 140 352 M16 69 A2
32-160/15/P 32 50 80 350 390 791 600 900 150 60 232 160 392 M16 73 A3
32-160/22/P 32 50 80 350 390 791 600 900 150 60 232 160 392 M16 75 A3
32-200/30/P 32 50 80 350 390 822 600 900 150 60 260 180 440 M16 95 B1
32-200/40/P 32 50 80 350 390 825 600 900 150 60 260 180 440 M16 97 B1
32-250/55/P 32 50 100 440 490 910 740 1120 190 75 280 225 505 M20 130 C1
32-250/75/P 32 50 100 440 490 910 740 1120 190 75 280 225 505 M20 134 C1
32-250/110/P 32 50 100 490 540 1067 840 1250 205 75 280 225 520 M20 181 C2
40-125/11/S 40 65 80 350 390 746 600 900 150 60 212 140 352 M16 70 A2
40-125/15/P 40 65 80 350 390 791 600 900 150 60 212 140 352 M16 74 A3
40-125/22/P 40 65 80 350 390 791 600 900 150 60 212 140 352 M16 77 A3
40-160/30/P 40 65 80 350 390 822 600 900 150 60 232 160 392 M16 92 B1
40-160/40/P 40 65 80 350 390 825 600 900 150 60 232 160 400 M16 96 B1
40-200/55/P 40 65 100 400 450 910 660 1000 170 60 260 180 451 M20 123 C1
40-200/75/P 40 65 100 400 450 910 660 1000 170 60 260 180 451 M20 128 C1
40-250/110A/P 40 65 100 490 540 1067 840 1250 205 75 280 225 520 M20 167 C2
40-250/110/P 40 65 100 490 540 1067 840 1250 205 75 280 225 520 M20 170 C2
40-250/150/P 40 65 100 490 540 1067 840 1250 205 75 280 225 520 M20 175 C2
50-125/22/P 50 65 100 350 390 811 600 900 150 60 232 160 392 M16 84 A3
50-125/30/P 50 65 100 350 390 842 600 900 150 60 232 160 392 M16 92 B1
50-125/40/P 50 65 100 350 390 845 600 900 150 60 232 160 400 M16 95 B1
50-160/55/P 50 65 100 400 450 910 660 1000 170 60 260 180 451 M20 120 C1
50-160/75/P 50 65 100 400 450 910 660 1000 170 60 260 180 451 M20 122 C1
50-200/110A/P 50 65 100 440 490 1067 740 1120 190 60 260 200 500 M20 145 C2
50-200/110/P 50 65 100 440 490 1067 740 1120 190 60 260 200 500 M20 150 C2
50-250/150/P 50 65 100 490 540 1067 840 1250 205 75 280 225 520 M20 165 C2
50-250/185/P 50 65 100 490 540 1067 840 1250 205 75 280 225 520 M20 170 C2
50-250/220/W 50 65 100 490 540 1127 840 1250 205 75 280 225 559 M20 246 D1
65-160/40/P 65 80 100 400 450 845 660 1000 170 75 260 200 460 M20 133 B1
65-160/55/P 65 80 100 440 490 910 740 1120 190 75 260 200 460 M20 155 C1
65-160/75/P 65 80 100 440 490 910 740 1120 190 75 260 200 460 M20 159 C1
65-160/110A/P 65 80 100 490 540 1067 840 1250 205 75 260 200 500 M20 162 C2
65-160/110/P 65 80 100 490 540 1067 840 1250 205 75 260 200 500 M20 162 C2
65-200/150/P 65 80 100 490 540 1067 840 1250 205 75 280 225 520 M20 185 C2
65-200/185/P 65 80 100 490 540 1067 840 1250 205 75 280 225 520 M20 190 C2
65-200/220/W 65 80 100 490 540 1127 840 1250 205 75 280 225 559 M20 274 D1
65-250/300/W 65 80 100 550 610 1340 940 1400 230 90 310 250 627 M24 367 E1
65-250/370/W 65 80 100 550 610 1340 940 1400 230 90 310 250 627 M24 403 E1
80-160/110/P 80 100 125 490 540 1092 840 1250 205 75 280 225 520 M20 198 C2
80-160/150/P 80 100 125 490 540 1092 840 1250 205 75 280 225 520 M20 209 C2
80-160/185/P 80 100 125 490 540 1092 840 1250 205 75 280 225 520 M20 220 C2
80-200/220/W 80 100 125 490 540 1262 840 1250 205 75 280 250 559 M20 302 D2
80-200/300/W 80 100 125 550 610 1365 940 1400 230 75 310 250 627 M24 373 E1
80-200/370/W 80 100 125 550 610 1365 940 1400 230 75 310 250 627 M24 402 E1
80-250/450/W 80 100 125 550 610 1454 940 1400 230 90 365 280 749 M24 501 E1
80-250/550/W 80 100 125 600 660 1563 1060 1600 270 90 390 280 792 M24 582 F1
80-250/750/W 80 100 125 670 730 1670 1200 1800 300 90 420 280 892 M24 700 G1
ESHF_2p50-en_a_td
91
ESHF SERIES
92
ESHF SERIES
DIMENSIONI E PESI
DIMENSIONS AND SERIE ESHF 4 poli
WEIGHTS AT 50
50Hz
Hz, 4 POLES
PUMP TYPE DIMENSIONS (mm) s WEIGHT COUPLING
ESHF..4 FOR TYPE
DNM DNA a B1 B2 L1 L2 L3 G M h1 h2 Hmax SCREWS kg

25-125/02A/S 25 50 80 320 360 704 540 800 130 60 212 140 352 M16 72 A1
25-125/02/S 25 50 80 320 360 704 540 800 130 60 212 140 352 M16 72 A1
25-160/02A/S 25 50 80 320 360 704 540 800 130 60 232 160 392 M16 74 A1
25-160/02/S 25 50 80 320 360 704 540 800 130 60 232 160 392 M16 74 A1
25-200/03/S 25 50 80 320 360 704 540 800 130 60 260 180 440 M16 78 A1
25-200/05/S 25 50 80 320 360 746 540 800 130 60 260 180 440 M16 80 A2
25-250/07/X 25 50 100 400 450 734 660 1000 170 75 280 225 505 M20 98 A2
25-250/11/P 25 50 100 400 450 811 660 1000 170 75 280 225 505 M20 106 A3
25-250/15/P 25 50 100 400 450 811 660 1000 170 75 280 225 505 M20 108 A3
32-125/02A/S 32 50 80 320 360 704 540 800 130 60 212 140 352 M16 72 A1
32-125/02/S 32 50 80 320 360 704 540 800 130 60 212 140 352 M16 72 A1
32-160/02A/S 32 50 80 320 360 704 540 800 130 60 232 160 392 M16 74 A1
32-160/02/S 32 50 80 320 360 704 540 800 130 60 232 160 392 M16 74 A1
32-200/03/S 32 50 80 320 360 704 540 800 130 60 260 180 440 M16 78 A1
32-200/05/S 32 50 80 320 360 746 540 800 130 60 260 180 440 M16 80 A2
32-250/07/X 32 50 100 400 450 734 660 1000 170 75 280 225 505 M20 98 A2
32-250/11/P 32 50 100 400 450 811 660 1000 170 75 280 225 505 M20 106 A3
32-250/15/P 32 50 100 400 450 811 660 1000 170 75 280 225 505 M20 108 A3
40-125/02A/S 40 65 80 320 360 704 540 800 130 60 212 140 352 M16 57 A1
40-125/02/S 40 65 80 320 360 704 540 800 130 60 212 140 352 M16 57 A1
40-160/03/S 40 65 80 320 360 704 540 800 130 60 232 160 392 M16 60 A1
40-160/05/S 40 65 80 320 360 746 540 800 130 60 232 160 392 M16 62 A2
40-200/07/X 40 65 100 350 390 734 600 900 150 60 260 180 440 M16 70 A2
40-200/11/P 40 65 100 350 390 811 600 900 150 60 260 180 440 M16 78 A3
40-250/11/P 40 65 100 400 450 811 660 1000 170 75 280 225 505 M20 105 A3
40-250/15/P 40 65 100 400 450 811 660 1000 170 75 280 225 505 M20 108 A3
40-250/22/P 40 65 100 400 450 888 660 1000 170 75 280 225 505 M20 131 B1
50-125/02/S 50 65 100 320 360 724 540 800 130 60 232 160 392 M16 59 A1
50-125/03/S 50 65 100 320 360 724 540 800 130 60 232 160 392 M16 59 A1
50-125/05/S 50 65 100 320 360 766 540 800 130 60 232 160 392 M16 61 A2
50-160/07/X 50 65 100 350 390 734 600 900 150 60 260 180 440 M16 69 A2
50-160/11/P 50 65 100 350 390 811 600 900 150 60 260 180 440 M16 77 A3
50-200/11/P 50 65 100 350 390 811 600 900 150 60 260 200 460 M16 88 A3
50-200/15/P 50 65 100 350 390 811 600 900 150 60 260 200 460 M16 91 A3
50-250/22A/P 50 65 100 400 450 888 660 1000 170 75 280 225 505 M20 132 B1
50-250/22/P 50 65 100 400 450 888 660 1000 170 75 280 225 505 M20 132 B1
50-250/30/P 50 65 100 400 450 888 660 1000 170 75 280 225 505 M20 136 B1
65-200/15/P 65 80 100 400 450 811 660 1000 170 75 280 225 505 M20 109 A3
65-200/22/P 65 80 100 440 490 888 740 1120 190 75 280 225 505 M20 133 B1
65-200/30/P 65 80 100 440 490 888 740 1120 190 75 280 225 505 M20 137 B1
65-250/40/P 65 80 100 440 490 1031 740 1120 190 90 310 250 550 M20 178 C3
65-250/55/P 65 80 100 440 490 1058 740 1120 190 90 310 250 550 M20 193 C4
80-160/15/P 80 100 125 400 450 836 660 1000 170 75 280 225 505 M20 127 A3
80-160/22A/P 80 100 125 440 490 913 740 1120 190 75 280 225 505 M20 143 B1
80-160/22/P 80 100 125 440 490 913 740 1120 190 75 280 225 505 M20 143 B1
80-200/30/P 80 100 125 440 490 1023 740 1120 190 75 280 250 530 M20 162 C3
80-200/40/P 80 100 125 440 490 1056 740 1120 190 75 280 250 530 M20 171 C3
80-250/55/P 80 100 125 490 540 1083 840 1250 205 90 310 280 590 M20 194 C4
80-250/75/P 80 100 125 490 540 1083 840 1250 205 90 310 280 590 M20 198 C4
80-250/110/P 80 100 125 490 540 1202 840 1250 205 90 310 280 590 M20 256 C5
ESHF_4p50-en_a_td
93
ESHC SERIES
94
ESHC SERIES
DIMENSIONI E PESI
DIMENSIONS AND SERIE ESHC 2 poli
WEIGHTS AT 5050 Hz
Hz, 2 POLES
PUMP TYPE DIMENSIONS (mm) s WEIGHT
COUPLING
TYPE
ESHC..2 FOR
DNM DNA a B1 B2 L1 L2 L3 G M h1 h2 Hmax f x SCREWS kg

32-125/07/S 32 50 80 320 360 845 540 800 130 60 212 140 352 360 100 M16 69 A2S
32-125/11/S 32 50 80 320 360 845 540 800 130 60 212 140 352 360 100 M16 71 A2S
32-160/15/P 32 50 80 350 390 889 600 900 150 60 232 160 392 360 100 M16 75 A3S
32-160/22/P 32 50 80 350 390 889 600 900 150 60 232 160 392 360 100 M16 77 A3S
32-200/30/P 32 50 80 350 390 920 600 900 150 60 260 180 440 360 100 M16 97 B1S
32-200/40/P 32 50 80 350 390 923 600 900 150 60 260 180 440 360 100 M16 99 B1S
32-250/55/P 32 50 100 440 490 1007 740 1120 190 75 280 225 505 360 100 M20 132 C1S
32-250/75/P 32 50 100 440 490 1007 740 1120 190 75 280 225 505 360 100 M20 136 C1S
32-250/110/P 32 50 100 490 540 1164 840 1250 205 75 280 225 520 360 100 M20 183 C2S
40-125/11/S 40 65 80 350 390 845 600 900 150 60 212 140 352 360 100 M16 72 A2S
40-125/15/P 40 65 80 350 390 889 600 900 150 60 212 140 352 360 100 M16 76 A3S
40-125/22/P 40 65 80 350 390 889 600 900 150 60 212 140 352 360 100 M16 79 A3S
40-160/30/P 40 65 80 350 390 920 600 900 150 60 232 160 392 360 100 M16 94 B1S
40-160/40/P 40 65 80 350 390 923 600 900 150 60 232 160 400 360 100 M16 98 B1S
40-200/55/P 40 65 100 400 450 1007 660 1000 170 60 260 180 451 360 100 M20 125 C1S
40-200/75/P 40 65 100 400 450 1007 660 1000 170 60 260 180 451 360 100 M20 130 C1S
40-250/110A/P 40 65 100 490 540 1164 840 1250 205 75 280 225 520 360 100 M20 169 C2S
40-250/110/P 40 65 100 490 540 1164 840 1250 205 75 280 225 520 360 100 M20 172 C2S
40-250/150/P 40 65 100 490 540 1164 840 1250 205 75 280 225 520 360 100 M20 177 C2S
50-125/22/P 50 65 100 350 390 909 600 900 150 60 232 160 392 360 100 M16 86 A3S
50-125/30/P 50 65 100 350 390 940 600 900 150 60 232 160 392 360 100 M16 94 B1S
50-125/40/P 50 65 100 350 390 943 600 900 150 60 232 160 400 360 100 M16 97 B1S
50-160/55/P 50 65 100 400 450 1007 660 1000 170 60 260 180 451 360 100 M20 122 C1S
50-160/75/P 50 65 100 400 450 1007 660 1000 170 60 260 180 451 360 100 M20 124 C1S
50-200/110A/P 50 65 100 440 490 1164 740 1120 190 60 260 200 500 360 100 M20 147 C2S
50-200/110/P 50 65 100 440 490 1164 740 1120 190 60 260 200 500 360 100 M20 152 C2S
50-250/150/P 50 65 100 490 540 1164 840 1250 205 75 280 225 520 360 100 M20 167 C2S
50-250/185/P 50 65 100 490 540 1164 840 1250 205 75 280 225 520 360 100 M20 172 C2S
50-250/220/W 50 65 100 490 540 1224 840 1250 205 75 280 225 559 360 100 M20 248 D1S
65-160/40/P 65 80 100 400 450 943 660 1000 170 75 260 200 460 360 100 M20 135 B1S
65-160/55/P 65 80 100 440 490 1007 740 1120 190 75 260 200 460 360 100 M20 157 C1S
65-160/75/P 65 80 100 440 490 1007 740 1120 190 75 260 200 460 360 100 M20 161 C1S
65-160/110A/P 65 80 100 490 540 1164 840 1250 205 75 260 200 500 360 100 M20 164 C2S
65-160/110/P 65 80 100 490 540 1164 840 1250 205 75 260 200 500 360 100 M20 164 C2S
65-200/150/P 65 80 100 490 540 1164 840 1250 205 75 280 225 520 360 100 M20 187 C2S
65-200/185/P 65 80 100 490 540 1164 840 1250 205 75 280 225 520 360 100 M20 192 C2S
65-200/220/W 65 80 100 490 540 1224 840 1250 205 75 280 225 559 360 100 M20 276 D1S
65-250/300/W 65 80 100 550 610 1477 940 1400 230 90 310 250 627 470 140 M24 370 E1S
65-250/370/W 65 80 100 550 610 1477 940 1400 230 90 310 250 627 470 140 M24 406 E1S
80-160/110/P 80 100 125 490 540 1189 840 1250 205 75 280 225 520 360 100 M20 200 C2S
80-160/150/P 80 100 125 490 540 1189 840 1250 205 75 280 225 520 360 100 M20 211 C2S
80-160/185/P 80 100 125 490 540 1189 840 1250 205 75 280 225 520 360 100 M20 222 C2S
80-200/220/W 80 100 125 490 540 1359 840 1250 205 75 280 250 559 470 100 M20 304 D2S
80-200/300/W 80 100 125 550 610 1502 940 1400 230 75 310 250 627 470 140 M24 376 E1S
80-200/370/W 80 100 125 550 610 1502 940 1400 230 75 310 250 627 470 140 M24 405 E1S
80-250/450/W 80 100 125 550 610 1591 940 1400 230 90 365 280 749 470 140 M24 504 E1S
80-250/550/W 80 100 125 600 660 1700 1060 1600 270 90 390 280 792 470 140 M24 587 F1S
80-250/750/W 80 100 125 670 730 1807 1200 1800 300 90 420 280 892 470 140 M24 706 G1S
ESHC_2p50-en_a_td
95
ESH..H
(ESH WITH HYDROVAR)
96
ESH..H SERIES
(ESH WITH HYDROVAR)
Background and context Special features / benefits
In all areas of application, such as building services, There is no need for additional pressure
industry, agriculture and air-handling, the demand for sensors: ESH..H are fitted with a pressure transmitter
intelligent pumping systems is constantly growing. or differential pressure transmitters, depending on the
There are many advantages: reduced cost for pump life application.
cycle, lower environmental impact, longer lifetime of
pipes and unions. Thats why Xylem has developed the There is no need for special pumps or
ESH..H: an intelligent pumping system which assures high motors.
level performance with energy consumption tailored to
demand. There is no need for bypass or safety
systems: with HYDROVAR the pump immediately
Benefits of NSC with HYDROVAR switches off when demand drops to zero or when it
exceeds maximum pump capacity. This makes it
Saving: ESH..H transforms ESH pumps into variable unnecessary to install additional safety devices.
speed intelligent pumping systems. Thanks to the
HYDROVAR system, the speed of each pump varies so Anti-condensation device: all units are fitted
as to maintain a constant flow or pressure or differential with anti-condensation devices which switch on when
pressure. The pump only receives the energy required, the pump is in standby in order to prevent condensation
thus allowing considerable savings, especially for those forming in the unit.
systems in which demands varies during the day.
Easy installation and space-saving: ESH..H saves

time and space during installation. Installed directly on
the motor (up to 22 kW), which cools it down, and does
not require a further control panel. , only fuses on the
supply line (will depend upon any local electrical installation
regulations). The wall-mounted HYDROVAR version is
available for higher power outputs (up to 45 kW).
Standard motors: ESH..H models are fitted with

three-phase standard TEFC motors with insulation class
155 (F).
NSC_M0004_A_ot
97
ESH..H SERIES Lowara
(ESH WITH HYDROVAR)
OPERATING PRINCIPLE
The basic function of the HYDROVAR device is to control the
pump to meet the system demands.
The basic function of the HYDROVAR device is to
control the pump to meet the system demands.
HYDROVAR performs these functions by:
1) Measuring
HYDROVAR the system pressure or flow via a
performs these functions by:
transmitter
1) Measuring the mounted
system on the pumps
pressure or flow delivery
via a side.
2)transmitter
Calculatingmounted
the motoronspeed to maintain
the pumps delivery theside.
correct
flow or pressure.
2) Calculating the motor speed to maintain the correct
3)flow
Sending out a signal to the pump to start the motor,
or pressure.
increase out
3) Sending speed, decrease
a signal to the speed
pump ortostop.
start the motor, Control for constant pressure
4)increase
In the case of multiple pump
speed, decrease speed or stop. installations,
4) In the case ofwill
HYDROVAR multiple pump installations,
automatically provide for the cyclic
HYDROVAR
changeover of willtheautomatically
pumps starting provide for the cyclic
sequence.
changeover of the pumps starting sequence
In addition to these basic functions, HYDROVAR can do
In addition
things onlytobythese
the mostbasicadvanced
functions,computerised
HYDROVAR control can do
things only by
systems, such as: the most advanced computerised control
systems,
Stop the such as:
pump(s) at zero demand.
Stop
Stop the pump(s)at
the pump(s) in zero
case demand.
of water failure on the suction
Stop the pump(s) in casedry
side (protection against running).
of water failure on the
suction
Stop the pump
side if the required
(protection againstdelivery exceeds the pumps
dry running).
Stop the pump if the required delivery exceeds by
capacity (protection against cavitation caused theexcessive Control to match a system curve
pumps capacity (protection against cavitation causedin a
demand), or automatically switch on the next pump
multiple
by series.
excessive demand), or automatically switch on the
next
Protect
pumptheinpump and motor
a multiple series.from overvoltage,
Protect the pump and motorearth
undervoltage, overload and from fault.
overvoltage,
undervoltage,
Vary the pumpoverload
speed acceleration
and earth fault. and deceleration time.
Compensate for increased flow resistance at high flow
Vary the pump speed acceleration and deceleration
rates.
time.
Conduct automatic test starts at set intervals.
Compensate
Monitor the for increased
converter andflowmotor resistance
operating at high
hours.flow
rates.
Display all functions on an LCD in different languages
Conduct automatic
(Italian, English, test starts
French, German, at set intervals.
Spanish, Portuguese,
Control for constant flow
Monitor
Dutch). the converter and motor operating hours.
Display
Send a all
signal to a remote
functions on an control system which
LCD in different is
languages
proportional
(Italian, English,to the
French,pressure
German,and Spanish,
frequency. Portuguese,
Dutch).
Communicate with another HYDROVAR or control
system via anto
Send a signal RSa485 remoteinterface.
control system which is
proportional to the pressure and frequency.
Communicate with another HYDROVAR or control
system via an RS 485 interface.
Control according to an external signal
TYPICAL EXAMPLE OF ENERGY SAVINGS

System: SV1608F75T vertical multistage electric pump with 7.5 kW motor equipped with Hydrovar, 80 m head. 12
hour/day operation.
Application: maintaining a constant pressure as the flow rate varies.
FLOW ABSORBED POWER POWER OPERATING TOTAL
CONSTANT SPEED VARIABLE SPEED SAVED TIME ENERGY
PUMP PUMP SAVINGS
m3/h kW kW kW (hours) kWh

9 5,50 3,09 2,41 1095 2639
14 6,71 4,81 1,90 2190 4161
21 7,30 7,21 0,09 1095 99
YEARLY ENERGY SAVINGS (kWh) 6899
98
ACCESSORIES
99
FLEXIBLE COUPLING DIMENSIONS
SHF DIMENSIONI GIUNTO ELASTICO
REF. DENOMINATION DIMENSIONS (mm)

K1 K4
PUMP-SIDE HALF COUPLING MOTOR-SIDE HALF COUPLING
H7 js9 +0.2 H7 js9 +0.2
SIZE x d1 x d2 d1 l1 b1 t1 0 s1 q1 u d2 l2 b2 t2 0 s2 q2
A1 B 68 x 24 x 14 24 20 8 27,3 M6 10 24 14 20 5 16,3 M6 8
A2 B 68 x 24 x 19 24 20 8 27,3 M6 10 24 19 20 6 21,8 M6 8
A3 B 68 x 24 x 24 24 20 8 27,3 M6 10 24 24 20 8 27,3 M6 8
B1 B 80 x 24 x 28 24 30 8 27,3 M6 19 24 28 30 8 31,3 M6 12
C1 B 95 x 24 x 38 24 35 8 27,3 M6 20 24 38 35 10 41,3 M6 15
C2 B 95 x 24 x 42 24 35 8 27,3 M6 20 24 42 35 12 45,3 M6 15
C3 B 95 x 32 x 28 32 35 10 35,3 M6 20 24 28 35 8 31,3 M6 15
C4 B 95 x 32 x 38 32 35 10 35,3 M6 20 24 38 35 10 41,3 M6 15
C5 B 95 x 32 x 42 32 35 10 35,3 M6 20 24 42 35 12 45,3 M6 15
D1 B 110 x 24 x 48 24 40 8 27,3 M6 22 24 48 40 14 51,8 M6 18
D2 B 110 x 32 x 48 32 40 10 35,3 M6 22 24 48 40 14 51,8 M6 18
E1 B 125 x 32 x 55 32 50 10 35,3 M8 30 24 55 50 16 59,3 M8 20
F1 B 140 x 32 x 60 32 55 10 35,3 M8 13 24 60 55 18 64,4 M8 22
G1 B 160 x 32 x 65 32 60 10 35,3 M10 13 26 65 60 18 69,4 M10 25
shf-giunto-elastico-en_c_td
N.B.: Non-ATEX version.
100
SPACER COUPLING DIMENSIONS
DIMENSIONI GIUNTO ELASTICO CON SPAZIATORE
REF. DENOMINATION DIMENSIONS (mm)

K1 K5
PUMP-SIDE HALF COUPLING MOTOR-SIDE HALF COUPLING
+1 H7 js9 +0.2 H7 js9 +0.2
SIXE x l x d1 x d2 l0 d1 l1 b1 t1 0 s1 q1 u d2 l2 b2 t2 0 s2 q2
A2S H 80-100 x 24 x 19 100 24 30 8 27,3 M6 19 5 19 45 6 21,8 M6 15
A3S H 80-100 x 24 x 24 100 24 30 8 27,3 M6 19 5 24 45 8 27,3 M6 15
B1S H 80-100 x 24 x 28 100 24 30 8 27,3 M6 19 5 28 45 8 31,3 M6 15
C1S H 95-100 x 24 x 38 100 24 35 8 27,3 M6 20 5 38 45 10 41,3 M6 20
C2S H 95-100 x 24 x 42 100 24 35 8 27,3 M6 20 5 42 45 12 45,3 M6 20
D1S H 110-100 x 24 x 48 100 24 40 8 27,3 M6 22 5 48 50 14 51,8 M6 25
D2S H 110-100 x 32 x 48 100 32 40 10 35,3 M6 22 5 48 50 14 51,8 M6 25
E1S H 125-140 x 32 x 55 140 32 50 10 35,3 M8 30 5 55 50 16 59,3 M8 25
F1S H 140-140 x 32 x 60 140 32 55 10 35,3 M8 13 5 60 65 18 64,4 M8 30
G1S H 160-140 x 32 x 65 140 32 60 10 35,3 M10 13 6 65 70 18 69,4 M10 35
sh-giunto-elastico-con-sp-en_c_td
N.B.: Non-ATEX version.
101
DIMENSIONS OF ROUND THREADED
COUNTERFLANGES ACCORDING TO EN 1092-1
DIMENSIONI CONTROFLANGE TONDE F

DIMENSIONS (mm) HOLES
DN C A B D H F N PN
25 Rp 1 85 10 115 16 14 4 16
32 Rp 1 100 13 140 16 18 4 16
40 Rp 1 110 14 150 19 18 4 16
50 Rp 2 125 16 165 24 18 4 16
65 Rp 2 145 16 185 23 18 4 16
80 Rp 3 160 17 200 27 18 8 16
100 Rp 4 180 18 220 31 18 8 16
sh-ctf-tonde-f-en_b_td
DIMENSIONS OF ROUND WELD-ON

COUNTERFLANGES ACCORDING TO EN 1092-1
DIMENSIONI CONTROFLANGE TONDE

DIMENSIONS (mm) HOLES
DN C A B D F N PN
65 77 145 18 185 18 4 16
80 90 160 20 200 18 8 16
100 115,5 180 22 220 18 8 16
sh-ctf-tonde-s-en_b_td
102
ESH SERIES
SHIM FOR MOTOR FEET
DIMENSIONI SPESSORI PER MOTORI SHF - SHS

DIMENSIONS (mm) DIMENSIONS (mm)
DENOMINATION HOLES DENOMINATION
b x h x l a l1 l2 c N s d1 x h d2
35 20 125 17 100 - 12,5 2 10 45 41 10
40 10 155 20 100 125 15 3 10 45 61 10
40 12 155 20 100 125 15 3 10 45 89 10
40 12 180 17 140 - 20 2 14 55 52 12
40 20 180 17 140 - 20 2 14 55 70 12
40 30 155 20 100 125 15 3 10 55 80 12
40 40 180 17 140 - 20 2 14 55 90 12
50 8 226 21 140 178 24 3 14 55 100 12
50 20 226 21 140 178 24 3 14 65 60 16
50 20 304 25 210 254 25 3 14 65 68 16
50 30 304 25 210 254 25 3 14 65 78 16
100 30 467 50 311 349 59 3 22 65 80 16
65 88 16
sp-mot-shs-shf-en_d_td
SHIM FOR PUMP FEET (ESHF)
DIMENSIONI SPESSORI POMPA SHF

DIMENSIONS (mm)
DESIGNATION
b x h x m1 a m2 s t
40 10 160 25 110 14 16,5
40 20 160 25 110 14 16,5
40 25 160 25 110 14 16,5
40 30 160 25 110 14 16,5
70 20 125 15 95 14 37,5
80 10 160 20 120 18 42,5
80 25 160 20 120 18 42,5
80 30 160 20 120 18 42,5
sp-pompa-shf-en_b_td
103
REPORTS AND
DECLARATIONS
104
REPORTS AND DECLARATIONS
i) Test reports
a) Factory Test Report (identity code: 1A)

(not available for all pump types; contact Customer Service in advance)
- Test report compiled at the end of the assembly line, including flow-head performance test
(ISO 9906:2012 Grade 3B) and tightness test.
b) Audit Test Report (identity code: 1B)

- Test report for electric pumps compiled in the test room, comprising flow-head-pump input-pump efficiency
performance test (ISO 9906:2012 Grade 3B)
c) NPSH Test Report (identity code: 1A / CTF-NP)

(unavailable for submerged or submergible pumps)
- Test report for electric pumps compiled in the test room, comprising flow-NPSH performance test
(ISO 9906:2012 Grade 3B)
d) Noise Test Report (identity code: 1A / CTF-RM)

(unavailable for submerged pumps)
- Report indicating sound pressure and power measurements (EN ISO 20361, EN ISO 11203, EN ISO 4871)
using the
intensimetric (EN ISO 9614-1, EN ISO 9614-2), or
phonometric method.
e) Vibration Test Report

(unavailable for submerged or submergible pumps)
- Report indicating vibration measurements (ISO 10816-1)
f) Declaration of product conformity with the technical requirements indicated in the order
a) EN 10204:2004 - type 2.1 (identity code: CTF-21)

- does not include test results on supplied or similar products.
b) EN 10204:2004 - type 2.2 (identity code: CTF-22)

- includes test results (materials certificates) on similar products.
c) EN 10204:2004 - type 3.1 (identity code: 1A / CTF-31 or 1B / CTF-31)

- includes test report (Factory Test Report or Audit Test Report), list of materials, EC Declaration of Conformity
(in addition to the one accompanying the product), certificates / declarations concerning materials in contact
with water.
d) Issue of a further EC Declaration of Conformity,

- in addition to the one accompanying the product, it comprises references to European law and the main
technical standards (e.g.: MD 2006/42/EC, EMCD 2004/108/EC, ErP 2009/125/EC).
N.B.: if the request is made after receipt of the product, communicate the code (name) and serial number (date
+ progressive number).
iv) Manufacturers declaration of conformity

- relative to one of more types of products without indicating specific codes and serial numbers.
v) Other certificates and/or documentation on request

- subject to availability or feasibility.
vi) Duplication of certificates and/or documentation on request

- subject to availability or feasibility.
105
106
TECHNICAL
APPENDIX
107
ESH SERIES
TYPICAL APPLICATIONS
Water Purification: Waste Management:
De-ionized water Waste treatment
Water Treatment Pollution control
Filtration
Commercial Pools
Food and Drink: Machine Tools:

Food processing Degreasing
Bottle washing Parts washing
Citrus Processing Machine centres
Dish washing Chemical treatment
Brewing Heat treatment
Sanitary ware
Medical: Vehicle Maintenance:

Laser cooling Car washing
Medical chillers Lorry of Truck wash
Sanitary equipment Wheel or tyre washing
Airplane washing
Heating, Ventilating &
Air Conditioning (HVAC) Marine:
Condensate return Water on board ships
Air scrubbers Boat design (wave machines)
Water re-circulation
Cooling towers Agriculture:
Cooling systems Irrigation
Temperature control Greenhouses
Chillaer Poultry Washing
Induction heating Cotton humidifiers
Heat exchangers
Water heating Computers:
Booster packages Washing of circuit boards
Graphics: Laundry:
Film washing Commercial washing
Cooling of presses
Plastics: General Industry:

Extrusion machines Spray Booths
Temperature control Light chemical transfer
Manufacture of polymers Booster systems
Fire fighting
TECHNICAL APPENDIX
108
NPSH
The minimum operating values that can be reached at the The maximum possible suction head for installation
pump suction end are limited by the onset of cavitation. depends on the value of the atmospheric pressure
(i.e. the elevation above sea level at which the pump
Cavitation is the formation of vapour-filled cavities within is installed) and the temperature of the liquid.
liquids where the pressure is locally reduced to a critical value,
or where the local pressure is equal to, or just below the To help the user, with reference to water temperature
vapour pressure of the liquid. (4 C) and to the elevation above sea level, the
following tables show the drop in hydraulic pressure
The vapour-filled cavities flow with the current and head in relation to the elevation above sea level, and
when they reach a higher pressure area the vapour the suction loss in relation to temperature.
contained in the cavities condenses. The cavities collide,
generating pressure waves that are transmitted to the Water
walls. These, being subjected to stress cycles, gradually temperature (C) 20 40 60 80 90 110 120
become deformed and yield due to fatigue. This Suction
phenomenon, characterized by a metallic noise loss (m) 0,2 0,7 2,0 5,0 7,4 15,4 21,5
produced by the hammering on the pipe walls, is called
incipient cavitation.
Elevation above
sea level (m) 500 1000 1500 2000 2500 3000
The damage caused by cavitation may be magnified by
electrochemical corrosion and a local rise in Suction
temperature due to the plastic deformation of the loss (m) 0,55 1,1 1,65 2,2 2,75 3,3
walls. The materials that offer the highest resistance to
heat and corrosion are alloy steels, especially austenitic Friction loss is shown in the tables at pages 111-112 of
steel. The conditions that trigger cavitation may be this catalogue. To reduce it to a minimum, especially
assessed by calculating the total net suction head, in cases of high suction head (over 4-5 m.) or within
referred to in technical literature with the acronym the operating limits with high flow rates, we
NPSH (Net Positive Suction Head). recommend using a suction line having a larger
diameter than that of the pumps suction port.
The NPSH represents the total energy (expressed in m.) It is always a good idea to position the pump as close
of the liquid measured at suction under conditions of as possible to the liquid to be pumped.
incipient cavitation, excluding the vapour pressure
(expressed in m.) that the liquid has at the pump inlet. Make the following calculation:
To find the static height hz at which to install the Liquid: water at ~15C = 1 kg/dm3
machine under safe conditions, the following formula Flow rate required: 25 m3/h
must be verified: Head for required delivery: 70 m.
Suction lift: 3,5 m.
hp + hz (NPSHr + 0.5) + hf + hpv 1
The selection is an 33SV3G075T pump whose NPSH
required value is, at 25 m3/h, of 2 m.
where:
hp is the absolute pressure applied to the free liquid For water at 15 C
surface in the suction tank, expressed in m. of
liquid; hp is the quotient between the barometric hp = Pa / = 10,33m, hpv = Pv / = 0,174m (0,01701 bar)
pressure and the specific weight of the liquid.
hz is the suction lift between the pump axis and the The Hf flow resistance in the suction line with foot
free liquid surface in the suction tank, expressed valves is ~ 1,2 m.
in m.; hz is negative when the liquid level is By substituting the parameters in formula 1 with the
lower than the pump axis. numeric values above, we have:
hf is the flow resistance in the suction line and its
accessories, such as: fittings, foot valve, gate 10,33 + (-3,5) (2 + 0,5) + 1,2 + 0,17
valve, elbows, etc.
hpv is the vapour pressure of the liquid at the from which we have: 6,8 > 3,9
operating temperature, expressed in m. of
liquid. hpv is the quotient between the Pv vapour The relation is therefore verified.
pressure and the liquids specific weight.
0,5 is the safety factor.
TECHNICAL APPENDIX
109
TENSIONE PRESSURE
VAPOUR DI VAPORE
TABELLA TENSIONE
VAPOUR PRESSUREDI VAPORE
ps ANDps DENSITY OF
E DENSITA' DELL'ACQUA
WATER TABLE
t T ps t T ps t T ps
C K bar kg/dm3 C K bar kg/dm3 C K bar kg/dm3
0 273,15 0,00611 0,9998 55 328,15 0,15741 0,9857 120 393,15 1,9854 0,9429
1 274,15 0,00657 0,9999 56 329,15 0,16511 0,9852 122 395,15 2,1145 0,9412
2 275,15 0,00706 0,9999 57 330,15 0,17313 0,9846 124 397,15 2,2504 0,9396
3 276,15 0,00758 0,9999 58 331,15 0,18147 0,9842 126 399,15 2,3933 0,9379
4 277,15 0,00813 1,0000 59 332,15 0,19016 0,9837 128 401,15 2,5435 0,9362
5 278,15 0,00872 1,0000 60 333,15 0,1992 0,9832 130 403,15 2,7013 0,9346
6 279,15 0,00935 1,0000 61 334,15 0,2086 0,9826 132 405,15 2,867 0,9328
7 280,15 0,01001 0,9999 62 335,15 0,2184 0,9821 134 407,15 3,041 0,9311
8 281,15 0,01072 0,9999 63 336,15 0,2286 0,9816 136 409,15 3,223 0,9294
9 282,15 0,01147 0,9998 64 337,15 0,2391 0,9811 138 411,15 3,414 0,9276
10 283,15 0,01227 0,9997 65 338,15 0,2501 0,9805 140 413,15 3,614 0,9258
11 284,15 0,01312 0,9997 66 339,15 0,2615 0,9799 145 418,15 4,155 0,9214
12 285,15 0,01401 0,9996 67 340,15 0,2733 0,9793 155 428,15 5,433 0,9121
13 286,15 0,01497 0,9994 68 341,15 0,2856 0,9788 160 433,15 6,181 0,9073
14 287,15 0,01597 0,9993 69 342,15 0,2984 0,9782 165 438,15 7,008 0,9024
15 288,15 0,01704 0,9992 70 343,15 0,3116 0,9777 170 433,15 7,920 0,8973
16 289,15 0,01817 0,9990 71 344,15 0,3253 0,9770 175 448,15 8,924 0,8921
17 290,15 0,01936 0,9988 72 345,15 0,3396 0,9765 180 453,15 10,027 0,8869
18 291,15 0,02062 0,9987 73 346,15 0,3543 0,9760 185 458,15 11,233 0,8815
19 292,15 0,02196 0,9985 74 347,15 0,3696 0,9753 190 463,15 12,551 0,8760
20 293,15 0,02337 0,9983 75 348,15 0,3855 0,9748 195 468,15 13,987 0,8704
21 294,15 0,24850 0,9981 76 349,15 0,4019 0,9741 200 473,15 15,550 0,8647
22 295,15 0,02642 0,9978 77 350,15 0,4189 0,9735 205 478,15 17,243 0,8588
23 296,15 0,02808 0,9976 78 351,15 0,4365 0,9729 210 483,15 19,077 0,8528
24 297,15 0,02982 0,9974 79 352,15 0,4547 0,9723 215 488,15 21,060 0,8467
25 298,15 0,03166 0,9971 80 353,15 0,4736 0,9716 220 493,15 23,198 0,8403
26 299,15 0,03360 0,9968 81 354,15 0,4931 0,9710 225 498,15 25,501 0,8339
27 300,15 0,03564 0,9966 82 355,15 0,5133 0,9704 230 503,15 27,976 0,8273
28 301,15 0,03778 0,9963 83 356,15 0,5342 0,9697 235 508,15 30,632 0,8205
29 302,15 0,04004 0,9960 84 357,15 0,5557 0,9691 240 513,15 33,478 0,8136
30 303,15 0,04241 0,9957 85 358,15 0,5780 0,9684 245 518,15 36,523 0,8065
31 304,15 0,04491 0,9954 86 359,15 0,6011 0,9678 250 523,15 39,776 0,7992
32 305,15 0,04753 0,9951 87 360,15 0,6249 0,9671 255 528,15 43,246 0,7916
33 306,15 0,05029 0,9947 88 361,15 0,6495 0,9665 260 533,15 46,943 0,7839
34 307,15 0,05318 0,9944 89 362,15 0,6749 0,9658 265 538,15 50,877 0,7759
35 308,15 0,05622 0,9940 90 363,15 0,7011 0,9652 270 543,15 55,058 0,7678
36 309,15 0,05940 0,9937 91 364,15 0,7281 0,9644 275 548,15 59,496 0,7593
37 310,15 0,06274 0,9933 92 365,15 0,7561 0,9638 280 553,15 64,202 0,7505
38 311,15 0,06624 0,9930 93 366,15 0,7849 0,9630 285 558,15 69,186 0,7415
39 312,15 0,06991 0,9927 94 367,15 0,8146 0,9624 290 563,15 74,461 0,7321
40 313,15 0,07375 0,9923 95 368,15 0,8453 0,9616 295 568,15 80,037 0,7223
41 314,15 0,07777 0,9919 96 369,15 0,8769 0,9610 300 573,15 85,927 0,7122
42 315,15 0,08198 0,9915 97 370,15 0,9094 0,9602 305 578,15 92,144 0,7017
43 316,15 0,09639 0,9911 98 371,15 0,9430 0,9596 310 583,15 98,70 0,6906
44 317,15 0,09100 0,9907 99 372,15 0,9776 0,9586 315 588,15 105,61 0,6791
45 318,15 0,09582 0,9902 100 373,15 1,0133 0,9581 320 593,15 112,89 0,6669
46 319,15 0,10086 0,9898 102 375,15 1,0878 0,9567 325 598,15 120,56 0,6541
47 320,15 0,10612 0,9894 104 377,15 1,1668 0,9552 330 603,15 128,63 0,6404
48 321,15 0,11162 0,9889 106 379,15 1,2504 0,9537 340 613,15 146,05 0,6102
49 322,15 0,11736 0,9884 108 381,15 1,3390 0,9522 350 623,15 165,35 0,5743
50 323,15 0,12335 0,9880 110 383,15 1,4327 0,9507 360 633,15 186,75 0,5275
51 324,15 0,12961 0,9876 112 385,15 1,5316 0,9491 370 643,15 210,54 0,4518
52 325,15 0,13613 0,9871 114 387,15 1,6362 0,9476 374,15 647,30 221,20 0,3154
53 326,15 0,14293 0,9862 116 389,15 1,7465 0,9460
54 327,15 0,15002 0,9862 118 391,15 1,8628 0,9445
G-at_npsh_b_sc
TECHNICAL APPENDIX
110
TABLE OF FLOW RESISTANCE IN 100 m OF STRAIGHT
CAST
TABELLAIRON
PERDITEPIPELINE
DI CARICO PER (HAZEN-WILLIAMS FORMULA
100 m TUBAZIONE DIRITTA IN GHISA C=100) C=100)
(FORMULA HAZEN-WILLIAMS
FLOW RATE NOMINAL DIAMETER in mm and inches

3
m /h l/min 15 20 25 32 40 50 65 80 100 125 150 175 200 250 300 350 400
1/2" 3/4" 1" 1 1/4" 1 1/2" 2 2 1/2" 3" 4" 5" 6" 7" 8" 10" 12" 14" 16"
v 0,94 0,53 0,34 0,21 0,13
0,6 10
hr 16 3,94 1,33 0,40 0,13 The hr values must be multiplied by:
v 1,42 0,80 0,51 0,31 0,20 0,71 for galvanized or painted steel pipes
0,9 15
hr 33,9 8,35 2,82 0,85 0,29 0,54 for stainless steel or copper pipes
v 1,89 1,06 0,68 0,41 0,27 0,17 0,47 for PVC or PE pipes
1,2 20
hr 57,7 14,21 4,79 1,44 0,49 0,16
v 2,36 1,33 0,85 0,52 0,33 0,21
1,5 25
hr 87,2 21,5 7,24 2,18 0,73 0,25
v 2,83 1,59 1,02 0,62 0,40 0,25
1,8 30
hr 122 30,1 10,1 3,05 1,03 0,35
v 3,30 1,86 1,19 0,73 0,46 0,30
2,1 35
hr 162 40,0 13,5 4,06 1,37 0,46
v 2,12 1,36 0,83 0,53 0,34 0,20
2,4 40
hr 51,2 17,3 5,19 1,75 0,59 0,16
v 2,65 1,70 1,04 0,66 0,42 0,25
3 50
hr 77,4 26,1 7,85 2,65 0,89 0,25
v 3,18 2,04 1,24 0,80 0,51 0,30
3,6 60
hr 108 36,6 11,0 3,71 1,25 0,35
v 3,72 2,38 1,45 0,93 0,59 0,35
4,2 70
hr 144 48,7 14,6 4,93 1,66 0,46
v 4,25 2,72 1,66 1,06 0,68 0,40
4,8 80
hr 185 62,3 18,7 6,32 2,13 0,59
v 3,06 1,87 1,19 0,76 0,45 0,30
5,4 90
hr 77,5 23,3 7,85 2,65 0,74 0,27
v 3,40 2,07 1,33 0,85 0,50 0,33
6 100
hr 94,1 28,3 9,54 3,22 0,90 0,33
v 4,25 2,59 1,66 1,06 0,63 0,41
7,5 125
hr 142 42,8 14,4 4,86 1,36 0,49
v 3,11 1,99 1,27 0,75 0,50 0,32
9 150
hr 59,9 20,2 6,82 1,90 0,69 0,23
v 3,63 2,32 1,49 0,88 0,58 0,37
10,5 175
hr 79,7 26,9 9,07 2,53 0,92 0,31
v 4,15 2,65 1,70 1,01 0,66 0,42
12 200
hr 102 34,4 11,6 3,23 1,18 0,40
v 5,18 3,32 2,12 1,26 0,83 0,53 0,34
15 250
hr 154 52,0 17,5 4,89 1,78 0,60 0,20
v 3,98 2,55 1,51 1,00 0,64 0,41
18 300
hr 72,8 24,6 6,85 2,49 0,84 0,28
v 5,31 3,40 2,01 1,33 0,85 0,54 0,38
24 400
hr 124 41,8 11,66 4,24 1,43 0,48 0,20
v 6,63 4,25 2,51 1,66 1,06 0,68 0,47
30 500
hr 187 63,2 17,6 6,41 2,16 0,73 0,30
v 5,10 3,02 1,99 1,27 0,82 0,57 0,42
36 600
hr 88,6 24,7 8,98 3,03 1,02 0,42 0,20
v 5,94 3,52 2,32 1,49 0,95 0,66 0,49
42 700
hr 118 32,8 11,9 4,03 1,36 0,56 0,26
v 6,79 4,02 2,65 1,70 1,09 0,75 0,55
48 800
hr 151 42,0 15,3 5,16 1,74 0,72 0,34
v 7,64 4,52 2,99 1,91 1,22 0,85 0,62
54 900
hr 188 52,3 19,0 6,41 2,16 0,89 0,42
v 5,03 3,32 2,12 1,36 0,94 0,69 0,53
60 1000
hr 63,5 23,1 7,79 2,63 1,08 0,51 0,27
v 6,28 4,15 2,65 1,70 1,18 0,87 0,66
75 1250
hr 96,0 34,9 11,8 3,97 1,63 0,77 0,40
v 7,54 4,98 3,18 2,04 1,42 1,04 0,80
90 1500
hr 134 48,9 16,5 5,57 2,29 1,08 0,56
v 8,79 5,81 3,72 2,38 1,65 1,21 0,93
105 1750
hr 179 65,1 21,9 7,40 3,05 1,44 0,75
v 6,63 4,25 2,72 1,89 1,39 1,06 0,68
120 2000
hr 83,3 28,1 9,48 3,90 1,84 0,96 0,32
v 8,29 5,31 3,40 2,36 1,73 1,33 0,85
150 2500
hr 126 42,5 14,3 5,89 2,78 1,45 0,49
v 6,37 4,08 2,83 2,08 1,59 1,02 0,71
180 3000
hr 59,5 20,1 8,26 3,90 2,03 0,69 0,28
v 7,43 4,76 3,30 2,43 1,86 1,19 0,83
210 3500
hr 79,1 26,7 11,0 5,18 2,71 0,91 0,38
v 8,49 5,44 3,77 2,77 2,12 1,36 0,94
240 4000
hr 101 34,2 14,1 6,64 3,46 1,17 0,48
v 6,79 4,72 3,47 2,65 1,70 1,18
300 5000
hr 51,6 21,2 10,0 5,23 1,77 0,73
v 8,15 5,66 4,16 3,18 2,04 1,42
360 6000
hr 72,3 29,8 14,1 7,33 2,47 1,02
v 6,61 4,85 3,72 2,38 1,65 1,21
420 7000
hr 39,6 18,7 9,75 3,29 1,35 0,64
v 7,55 5,55 4,25 2,72 1,89 1,39
480 8000
hr 50,7 23,9 12,49 4,21 1,73 0,82
v 8,49 6,24 4,78 3,06 2,12 1,56 1,19
540 9000
hr 63,0 29,8 15,5 5,24 2,16 1,02 0,53
v 6,93 5,31 3,40 2,36 1,73 1,33
600 10000
hr 36,2 18,9 6,36 2,62 1,24 0,65
G-at-pct-en_a_th
hr = flow resistance for 100 m of straight pipeline (m)
V = water speed (m/s)
TECHNICAL APPENDIX
111
FLOW RESISTANCE
TABLE OF FLOW RESISTANCE IN BENDS, VALVES AND
GATES
The flow resistance is calculated using the equivalent pipeline length method according to the table below:
TABELLA LUNGHEZZA DI TUBAZIONE EQUIVALENTE
ACCESSORY DN
TYPE 25 32 40 50 65 80 100 125 150 200 250 300
Equivalent pipeline length (m)
45 bend 0,2 0,2 0,4 0,4 0,6 0,6 0,9 1,1 1,5 1,9 2,4 2,8
90 bend 0,4 0,6 0,9 1,1 1,3 1,5 2,1 2,6 3,0 3,9 4,7 5,8
90 smooth bend 0,4 0,4 0,4 0,6 0,9 1,1 1,3 1,7 1,9 2,8 3,4 3,9
Union tee or cross 1,1 1,3 1,7 2,1 2,6 3,2 4,3 5,3 6,4 7,5 10,7 12,8
Gate - - - 0,2 0,2 0,2 0,4 0,4 0,6 0,9 1,1 1,3
Non return valve 1,1 1,5 1,9 2,4 3,0 3,4 4,7 5,9 7,4 9,6 11,8 13,9
G-a-pcv-en_a_th
The table is valid for the Hazen Williams coefficient C=100 (cast iron pipework);
for steel pipework, multiply the values by 1,41;
for stainless steel, copper and coated cast iron pipework, multiply the values by 1,85;
When the equivalent pipeline length has been determined, the flow resistance is obtained from the table of
flow resistance.
The values given are guideline values which are bound to vary slightly according to the model, especially for gate
valves and non-return valves, for which it is a good idea to check the values supplied by manufacturers.
TECHNICAL APPENDIX
112
VOLUMETRIC CAPACITY
Litres Cubic metres Cubic feet Cubic feet Imperial gallon U.S. gallon
per minute per hour per hour per minute per minute per minute
l/min m3/h ft3/h ft3/min Imp. gal/min US gal/min
1,0000 0,0600 2,1189 0,0353 0,2200 0,2642
16,6667 1,0000 35,3147 0,5886 3,6662 4,4029
0,4719 0,0283 1,0000 0,0167 0,1038 0,1247
28,3168 1,6990 60,0000 1,0000 6,2288 7,4805
4,5461 0,2728 9,6326 0,1605 1,0000 1,2009
3,7854 0,2271 8,0208 0,1337 0,8327 1,0000
PRESSURE AND HEAD

Newton per kilo Pascal bar Pound force per Metre Millimetre of
square metre square inch of water mercury
N/m2 kPa bar psi m H2O mm Hg
1,0000 0,0010 1 x 10-5 1,45 x 10-4 1,02 x 10-4 0,0075
1 000,0000 1,0000 0,0100 0,1450 0,1020 7,5006
1 x 105 100,0000 1,0000 14,5038 10,1972 750,0638
6 894,7570 6,8948 0,0689 1,0000 0,7031 51,7151
9 806,6500 9,8067 0,0981 1,4223 1,0000 73,5561
133,3220 0,1333 0,0013 0,0193 0,0136 1,0000
LENGTH
Millimetre Centimetre Metre Inch Foot Yard
mm cm m in ft yd
1,0000 0,1000 0,0010 0,0394 0,0033 0,0011

10,0000 1,0000 0,0100 0,3937 0,0328 0,0109
1 000,0000 100,0000 1,0000 39,3701 3,2808 1,0936
25,4000 2,5400 0,0254 1,0000 0,0833 0,0278
304,8000 30,4800 0,3048 12,0000 1,0000 0,3333
914,4000 91,4400 0,9144 36,0000 3,0000 1,0000
VOLUME
Cubic metre Litre Millilitre Imperial gallon U.S. gallon Cubic foot
m3 L ml imp. gal. US gal. ft3
1,0000 1 000,0000 1 x 106 219,9694 264,1720 35,3147

0,0010 1,0000 1 000,0000 0,2200 0,2642 0,0353
1 x 10-6 0,0010 1,0000 2,2 x 10-4 2,642 x 10-4 3,53 x 10-5
0,0045 4,5461 4 546,0870 1,0000 1,2009 0,1605
0,0038 3,7854 3 785,4120 0,8327 1,0000 0,1337
0,0283 28,3168 28 316,8466 6,2288 7,4805 1,0000
TEMPERATURE
Water Kelvin Celsius Fahrenheit
K C F F = C 95 + 32
icing 273,1500 0,0000 32,0000 C = (F 32) 59
boiling 373,1500 100,0000 212,0000
G-at_pp-en_b_sc
TECHNICAL APPENDIX
113
FURTHER PRODUCT SELECTION
AND DOCUMENTATION
XylectTM
XylectTM is pump solution selection software with an extensive online database of product information across the entire
range of pumps and related products, with multiple search options and helpful project management facilities. The
system holds up-to-date product information on thousands of products and accessories.
The possibility to search by applications and the detailed information output given makes it easy to make the optimal
selection without having detailed knowledge about the products.
The search can be made by:

Application
Product type
Duty point
XylectTM gives a detailed output:

List with search results
Performance curves (flow, head, power,
efficiency, NPSH)
Motor data
Dimensional drawings
Options
Data sheet printouts
The search by application guides users not familiar with
Document downloads incl dxf files the product range to the right choice.
TECHNICAL APPENDIX
114
FURTHER PRODUCT SELECTION
AND DOCUMENTATION
XylectTM
The detailed output makes it easy to select the optimal pump from the given alternatives.
The best way to work with XylectTM is to create a

personal account. This makes it possible to:
Set own standard units
Create and save projects
Share projects with other XylectTM users
Every user have a My Xylect space, where all projects

are saved.
Dimensional drawings appear on the screen and can be

For more information about XylectTM please contact downloaded in dxf format.
our sales network or visit www.xylect.com.
TECHNICAL APPENDIX
115
Xylem |zl m| e
1) The tissue in plants that brings water upward from the roots;
2) a leading global water technology company.
Were approximately 12,500 people unified in a common purpose: creating innovative solutions to meet our
worlds water needs. Developing new technologies that will improve the way water is used, conserved, and re-
used in the future is central to our work. We move, treat, analyze, and return water to the environment, and we
help people use water efficiently, in their homes, buildings, factories and farms. In more than 150 countries, we
have strong, long-standing relationships with customers who know us for our powerful combination of leading
product brands and applications expertise, backed by a legacy of innovation.
For more information on how Xylem can help you, go to xyleminc.com.
Legal head office For information and technical support

Xylem Water Solutions Italia Srl Xylem Service Italia Srl
Via Gioacchino Rossini 1/A Via Dottor Vittorio Lombardi 14

20020 Lainate (MI) - Italy 36075 - Montecchio Maggiore (VI) - Italy
Tel. (+39) 02 90358.1 Tel. (+39) 0444 707111
Fax (+39) 02 9019990 Fax (+39) 0444 491043
www.xylemwatersolutions.com
Xylem Water Solutions Italia Srl reserves the right to make modification without prior notice.
2015 Xylem, Inc.

eSH Technical Catalog PDF

Uploaded by

Copyright:

Available Formats

eSH Technical Catalog PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

eSH Technical Catalog PDF

Uploaded by

Copyright:

Available Formats

50 Hz

Cod. 191002961 Rev. A Ed.01/2015

XylectTM can be available:

On the website www.xylect.com On Mobile Apps

For more information, please, see page 114-115.

Ecodesign Directive (ErP)

List of Models at 50 Hz, 2 poles ................................................................................................... 10

Motors (ErP 2009/125/EC) ............................................................................................................ 18

Report and declarations ......................................................................................................... 104

ESH (2900 rpm)

ESH (1450 rpm)

Extended shaft Stub shaft

Frame mounted Bare shaft pump

Hydraulic specifications Motor specifications

List of the Directives and the main technical norms

- Electromagnetic Compatibility Directive EMCD 2004/108/EC EN 61000-6-1, EN 61000-6-3

- Ecodesign requirements for energy-related products EN 60034-30:2009, IEC 60034-30:2014

The e-SH Series can be used for the following CBS

Diverse OEM applications

Sizes DN25 to DN80.

The e-SH Series can be used for the following

Performances: the e-SH pumps are ErP 2015

Sizes DN25 to DN80.

Motor power [2 to 3 digits]

Size of the pump [6 digits] Electrical Voltage + Casing Material [1 digit]

ESHE, ESHS (ELECTRIC PUMP)

ESHF (ELECTRIC PUMP) ESH (PUMP ONLY)

REGULATION (EU) No 547/2012 REGULATION (EU) No 547/2012

ESHE..M : Close-coupled version with single-phase motor.

REF. NAME MATERIAL REFERENCE STANDARDS

** 2 pole: 65-160/40, 65-160/55, 65-160/75

REF. NAME MATERIAL REFERENCE STANDARDS

** 2 pole: 65-160/40, 65-160/55, 65-160/75

MATERIALI ESHS ESHS-p-en_a_mo

REF. NAME MATERIAL REFERENCE STANDARDS

** 2 pole: 65-160/40, 65-160/55, 65-160/75

REF. NAME MATERIAL REFERENCE STANDARDS

** 2 pole: 65-160/40, 65-160/55, 65-160/75

REF. NAME MATERIAL REFERENCE STANDARDS

** 2 pole: 65-160/40, 65-160/55, 65-160/75

(*) Standard version (**) Version with fixed assembly anti-rotation

TENUTA MECCANICA SH MATERIALI

B : Resin impregnated carbon E : EPDM G : AISI 316

TENUTA MECCANICA SH COMBINAZIONI

PRESSURE / TEMPERATURE APPLICATIONS LIMITS FOR COMPLETE PUMP

Regulations also establish the following deadlines.

Short-circuit squirrel-cage motor, enclosed Single-phase version:

Xylem Service Italia Srl Data for 400 V / 50 Hz Voltage

Reg. No. 07520560967

5,5 PLM112B14S2/355 E3 112 2 50 0,85 10,5 18,1 4,74 5,11

Y Y Altitude T. amb ATEX

Xylem Service Italia Srl Data for 400 V / 50 Hz Voltage

Reg. No. 07520560967

Y Y Altitude T. amb ATEX

Xylem Service Italia Srl Data for 400 V / 50 Hz Voltage

Reg. No. 07520560967

WEG Equipamentos Eletricos S.A. Data for 400 V / 50 Hz Voltage

Reg. No. 07.175.725/0010-50

22 40,70 39,00 37,90 23,40 22,60 2950 2960