GLASSES, WINDOW SYSTEM & MIRRORS

I BODY

B
SECTION
GLASSES, WINDOW SYSTEM & MIRRORS C

E
CONTENTS
WINDSHIELD GLASS ................................................ 2 Wiring Diagram WINDOW ................................ 13 F
Removal and Installation .......................................... 2 Terminals and Reference Value for Power Window
REMOVAL ............................................................. 2 Main Switch ............................................................ 15
INSTALLATION ..................................................... 3 Trouble Diagnosis Symptom Chart ......................... 15 G
SLIDE DOOR GLASS & SIDE WINDOW GLASS ..... 4 Power Window Main Switch Power Supply and
Push-in Type Weatherstrip ....................................... 4 Ground Circuit Check ............................................. 15
REMOVAL AND INSTALLATION .......................... 4 Driver Power Window Motor Check ........................ 16
H
Slide Glass Type ...................................................... 5 Power Window Main Switch Check ........................ 16
REMOVAL AND INSTALLATION .......................... 5 Passenger Power Window Switch Check ............... 17
BACK DOOR WINDOW GLASS ................................ 7 FRONT DOOR GLASS AND REGULATOR ............. 18
Removal and Installation .......................................... 7 Removal and Installation ........................................ 18 GW
REMOVAL ............................................................. 7 INSPECTION AFTER REMOVAL ....................... 20
INSTALLATION ..................................................... 8 FITTING INSPECTION ....................................... 20
BACK DOOR WINDOW DEFOGGER ........................ 9 DOOR MIRROR ........................................................ 21 J
System Description .................................................. 9 Removal and Installation ........................................ 21
TIMER FUNCTION ............................................... 9 REMOVAL (B) ..................................................... 21
ComponentParts and Harness Connector Location..... 9 INSTALLATION (B) .............................................. 21
K
Wiring Diagram DEF ........................................ 10 OUT SIDE MIRROR & UNDER MIRROR ................. 22
Terminals and Reference Value for Combination Removal and Installation ........................................ 22
Meter (Unified Meter Control Unit) ..........................11 REAR UNDER MIRROR ........................................... 23
POWER WINDOW SYSTEM .................................... 12 Removal and Installation ........................................ 23 L
ComponentParts and Harness Connector Location... 12

GW-1
 WINDSHIELD GLASS

WINDSHIELD GLASS PFP:72712

Removal and Installation EIS001LL

PIIA0410E

REMOVAL
1. Remove the front pillar garnish and head lining. Refer to EI-22, "BODY SIDE TRIM" and EI-27, "HEAD-
LINING" .
2. Remove the weather-strip on the front pillar.
3. Remove the cowl top cover. Refer to EI-13, "COWL TOP" .
4. Apply a protective tape around the windshield glass to protect the painted surface from damage.
After removing moldings, remove glass using piano wire or power cutting tool and an inflatable pump bag.
If a windshield glass is reversed, mark the body and the glass with mating marks.
WARNING:
When cutting the glass from the vehicle, always wear safety glasses and heavy gloves to help prevent
glass splinters from entering your eyes or cutting your hands.
CAUTION:
When a windshield glass is reused, do not use a cutting knife or power cutting tool.
NOTE:
Be careful not to scratch the glass when removing.

GW-2
 WINDSHIELD GLASS

Do not set or stand the glass on its edge. Small chips may develop into cracks.
A

PIIA0186E D
INSTALLATION
Use a genuine Nissan Urethane Adhesive Kit or equivalent and follow the instructions furnished with it.
E
While the urethane adhesive is curing, open a door window. This will prevent the glass from being forced
out by passenger compartment air pressure when a door is closed.
The molding must be installed securely so that it is in position and leaves no gap.
F
Inform the customer that the vehicle should remain stationary until the urethane adhesive has completely
cured (preferably 24 hours). Curing time varies with temperature and humidity.
WARNING: G
Keep heat and open flames away as primers and adhesive are flammable.
The materials contained in the kit are harmful if swallowed, and may irritate skin and eyes. Avoid
contact with the skin and eyes.
H
Use in an open, well ventilated location. Avoid breathing the vapors. They can be harmful if
inhaled. If affected by vapor inhalation, immediately move to an area with fresh air.
Driving the vehicle before the urethane adhesive has completely cured may affect the perfor-
GW
mance of the windshield in case of an accident.
CAUTION:
Do not use an adhesive which is past its usable term. Shelf life of this product is limited to six
months after the date of manufacture. Carefully adhere to the expiration or manufacture date J
printed on the box.
Keep primers and adhesive in a cool, dry place. Ideally, they should be stored in a refrigerator.
Do not leave primers or adhesive cartridge unattended with their caps open or off. K
The vehicle should not be driven for at least 24 hours or until the urethane adhesive has com-
pletely cured. Curing time varies depending on temperature and humidities. The curing time will
increase under higher temperatures and lower humidities. L

Repairing Water Leaks for Windshield

Leaks can be repaired without removing and reinstalling glass. M
If water is leaking between the urethane adhesive material and body or glass, determine the extent of leakage.
This can be done by applying water to the windshield area while pushing glass outward.
To stop the leak, apply primer (if necessary) and then urethane adhesive to the leak point.

GW-3
 SLIDE DOOR GLASS & SIDE WINDOW GLASS

SLIDE DOOR GLASS & SIDE WINDOW GLASS PFP:83300

Push-in Type Weatherstrip EIS001J9

REMOVAL AND INSTALLATION

PIIA0412E

Sliding door
Remove sliding door finisher. Refer to EI-19, "DOOR FINISHER" .
Side window glass 1st
Remove the following: center pillar upper garnish, rear pillar upper garnish and rear side upper finisher
(Front). Refer to EI-22, "BODY SIDE TRIM" .
Side window glass 2nd
Remove the following: center pillar upper garnish, back pillar upper garnish and rear side upper finisher
(Rear). Refer to EI-22, "BODY SIDE TRIM" .
Removal
Using a clip clamp tool in the cabin, pull weatherstrip outward to
remove.

SIIA1051E

Installation

SIIA1053E

GW-4
 SLIDE DOOR GLASS & SIDE WINDOW GLASS

1. Insert rope into body flange inserting groove of the weatherstrip. (Both ends of the rope should be tied
together at the lower center of weatherstrip.) A
2. Align weatherstrip and body flange. Pull the rope in cabin and push glass from outside (at the same time)
to fit weatherstrip and body flange.
3. After installing the glass, lightly tap weatherstrip all around with rubber hammer to completely fit weather- B
strip and body flange.
4. Install the removed parts.
C
Slide Glass Type EIS001JA

REMOVAL AND INSTALLATION

D

GW

PIIA0413E M
Sliding door
Remove sliding door finisher. Refer to EI-19, "DOOR FINISHER" .
Side window glass 1st
Remove the following: center pillar upper garnish, rear pillar upper garnish and rear side upper finisher
(Front). Refer to EI-22, "BODY SIDE TRIM" .
Side window glass 2nd
Remove the following: center pillar upper garnish, back pillar upper garnish and rear side upper finisher
(Rear). Refer to EI-22, "BODY SIDE TRIM" .
Removal
1. Remove body side welt. Refer to EI-22, "BODY SIDE TRIM" .
2. Apply protective tape on body panel along the circumference window glass to protect coated surfaces
from damage.

GW-5
 SLIDE DOOR GLASS & SIDE WINDOW GLASS

3. Working from inside the cabin, insert a cutter knife between

sash assembly and body panel. Then, cut off the adhesive.
CAUTION:
Cut carefully so that the tip end of cutter knife does not
contact sash assembly or painted surface.
4. Remove slide glass assembly out of body panel.
CAUTION:
The glass is very heavy. Be careful not to drop it.

BEC2418D

Installation
1. Using a knife, remove remaining sealant on body down to
approximately 2 mm (0.08 in) thick so that entire contour
becomes smooth.
CAUTION:
If coated panel surface is scratched or cut, always repair
with two-liquid type urethane paint. Do not use lacquer type
paint.

SIIA1097E

2. With white gasoline, clean bonding areas around body panel and slide glass assembly.
3. Apply primer along outer circumference of slide glass sash.
CAUTION:
If coated surface other than areas to be bonded is smeared
with Primer M, immediately wipe off with white gasoline.
4. After applying the primer, apply adhesive along entire circumfer-
ence within the time specified in the instruction manual.
5. Confirm installation position for slide glass assembly, and install
it into panel.
6. Lightly press across slide glass assembly for complete fitting.
7. Using a spatula, go over areas with excessive or insufficient SIIA1054E
adhesive and neatly smooth the surface.
CAUTION:
After installing the glass, allow some time until adhesive is cured. Do not drive the vehicle until
adhesive has finished curing.
8. Perform the leak test.
9. Peel off the protective tape. Install body side welt and other removed parts again.

GW-6
 BACK DOOR WINDOW GLASS

BACK DOOR WINDOW GLASS PFP:90300

A
Removal and Installation EIS001LM

GW

PIIA0411E
M
REMOVAL
1. Remove rear wiper. Refer to WW-13, "Removal and Installation for Rear Wiper Arms" .
2. Remove the rear pillar garnish. Refer to WW-15, "Removal and Installation for Rear Washer Nozzle" .
3. Remove the connectors and grounds for the rear defogger and printed antenna.
After removing moldings, remove glass using piano wire or power cutting tool and an inflatable pump bag.
If a windshield glass is revsed, mark the body and the glass with mating marks.
WARNING:
When cutting the glass from the vehicle, always wear safety glasses and heavy gloves to help prevent
glass splinters from entering your eyes or cutting your hands.
CAUTION:
When a windsheild glass is reused, do not use a cutting knife or power cutting tool.
Be careful not to scratch the glass when removing.

GW-7
 BACK DOOR WINDOW GLASS

Do not set or stand the glass on its edge. Small chips may develop into cracks.

PIIA0186E

INSTALLATION
Use a genuine Nissan Urethane Adhesive Kit or equivalent and follow the instructions furnished with it.
While the urethane adhesive is curing, open a door window. This will prevent the glass from being forced
out by passenger compartment air pressure when a door is closed.
The molding must be installed securely so that it is in position and leaves no gap.
Inform the customer that the vehicle should remain sta-tionary until the urethane adhesive has completely
cured (preferably 24 hours). Curing time varies with temperature and humidity.
WARNING:
Keep heat and open flames away as primers and adhesive are flammable.
The materials contained in the kit are harmful if swallowed, and may irritate skin and eyes. Avoid
contact with the skin and eyes.
Use in an open, well ventilated location. Avoid breathing the vapors. They can be harmful if
inhaled. If affected by vapor inhalation, immediately move to an area with fresh air.
Driving the vehicle before the urethane adhesive has completely cured may affect the perfor-
mance of the windshield in case of an accident.
CAUTION:
Do not use an adhesive which is past its usable term. Shelf life of this product is limited to six
months after the date of manufacture. Carefully adhere to the expiration or manufacture date
printed on the box.
Keep primers and adhesive in a cool, dry place. Ideally, they should be stored in a refrigerator.
Do not leave primers or adhesive cartridge unattended with their caps open or off.
The vehicle should not be driven for at least 24 hours or until the urethane adhesive has com-
pletely cured. Curing time varies depending on temperature and humidities. The curing time will
increase under higher temperatures and lower humidities.

GW-8
 BACK DOOR WINDOW DEFOGGER

BACK DOOR WINDOW DEFOGGER PFP:90300

A
System Description EIS0018L

TIMER FUNCTION
With ignition switch turned ON, when rear defogger switch is switched from OFF to ON, the switch sends B
an output signal to rear defogger, and simultaneously the timer starts (it remains ON for approximately 15
minutes).
With timer working, when rear defogger switch is turned from OFF to ON, timer will be stopped. Output to
defogger will also be stopped. When ignition switch is turned to ACC or OFF while timer is working, the C
same will happen.
The meter control unit inside the meter controls the timer while defogger is activated.
D
Component Parts and Harness Connector Location EIS0018M

GW

J
PIIA0531E

GW-9
 BACK DOOR WINDOW DEFOGGER

Wiring Diagram DEF EIS0018N

TIWH0010E

GW-10
 BACK DOOR WINDOW DEFOGGER

Terminals and Reference Value for Combination Meter (Unified Meter Control
Unit) EIS0018O
A

Wire Voltage
Terminal Item Condition
color (Approximate values) B
26 (43) G/B Rear defogger switch Rear defogger switch OFF ON Battery voltage 0V
52 (16) BR Rear defogger relay Rear defogger switch OFF ON Battery voltage 0V
67 (13) W/L IGN power supply Battery voltage C
11 (14) B Ground 0V
( ): With tachometer
D

GW

GW-11
 POWER WINDOW SYSTEM

POWER WINDOW SYSTEM PFP:25401

Component Parts and Harness Connector Location EIS001LN

PIIA0530E

GW-12
 POWER WINDOW SYSTEM

Wiring Diagram WINDOW EIS001LO

GW

TIWH0011E

GW-13
POWER WINDOW SYSTEM

TIWH0012E

GW-14
 POWER WINDOW SYSTEM

Terminals and Reference Value for Power Window Main Switch EIS001LP

A
Wire Voltage
Terminal Item Condition
color (Approximate values)
1 L/OR Driver power window motor DOWN Driver DOWN switch ON 0V Battery voltage
B
2 G/Y Driver power window motor UP Driver UP switch ON 0V Battery voltage
4 L/B BAT power supply Battery voltage
5 Y Passenger power window DOWN Passenger DOWN switch ON 0V Battery voltage C
6 L Passenger power window UP Passenger UP switch ON 0V Battery voltage
7 B Ground 0V
D
Trouble Diagnosis Symptom Chart EIS001LQ

Check that other systems using the signal of the following systems operate normally.
E
Symptom Diagnostic procedure
Power window main switch power supply and ground
All the power windows are inoperative. circuit check. F
Refer to GW-15 .
Driver power window motor check.
Driver power window does not operate.
Refer to GW-16 .
G
Passenger power window is inoperative. (The window can be oper- Power window main switch check.
ated with the passenger power window switch.) Refer to GW-16 .
Passenger power window is inoperative. (The window can be oper- Passenger power window switch check. H
ated with the power window main switch.) Refer to GW-17 .

Power Window Main Switch Power Supply and Ground Circuit Check EIS001LR

1. POWER WINDOW RELAY CIRCUIT CHECK GW

1. Disconnect power window main switch connector.

2. Turn ignition switch to ON. J
3. Check voltage between power window main switch harness connector D6 terminal 4(L/B) and body
ground.
K
: Battery should exist.
OK or NG?
OK >> GO TO 2. L
NG >> Check power window relay power supply circuit harness for open or short circuit.
Check harness for open or short between power window relay and power window main switch.

M
2. POWER WINDOW MAIN SWITCH GROUND CIRCUIT CHECK
Check continuity between power window main switch harness connector D6 terminal 7(B) and body ground.
: Continuity should exist.
OK or NG?
OK >> Replace power window main switch.
NG >> Check ground circuit harness for open or short circuit.

GW-15
 POWER WINDOW SYSTEM

Driver Power Window Motor Check EIS001LS

1. POWER WINDOW MOTOR CIRCUIT CHECK

1. Disconnect driver power window motor connector and power window main switch connector.
2. Check continuity between driver power window motor harness connector D5 terminals 1(L/OR), 2(G/Y)
and power window main switch harness connector D6 terminals 1(L/OR), 2(G/Y).
1-1 : Continuity should exist.
2-2 : Continuity should exist.
OK or NG?
OK >> GO TO 2.
NG >> Check harness for open or short between driver power window motor and power window main
switch.

2. POWER WINDOW MAIN SWITCH SIGNAL CHECK

1. Connect power window main switch connector.
2. Turn ignition switch to ON.
3. Check voltage between driver power window motor harness connector D5 terminals 1(L/OR), 2(G/Y) and
body ground.

Terminal Power window Voltage

(+) () main switch (Approximate values)
Driver DOWN
1(L/OR) 0V Battery voltage
Body switch ON
ground Driver UP
2(G/Y) 0V Battery voltage
switch ON
OK or NG?
OK >> Replace driver power window motor.
NG >> Replace power window main switch.
Power Window Main Switch Check EIS001LT

1. POWER WINDOW MAIN SWITCH CIRCUIT CHECK

1. Disconnect power window main switch connector and passenger power window switch connector.
2. Check continuity between power window main switch harness connector D6 terminals 5(Y), 6(L) and pas-
senger power window switch harness connector D24 terminals 3(L), 4(Y).
5-4 : Continuity should exist.
6-3 : Continuity should exist.
OK or NG?
OK >> Replace power window main switch.
NG >> Check harness for open or short between passenger power window switch and power window
main switch.

GW-16
 POWER WINDOW SYSTEM

Passenger Power Window Switch Check EIS001LU

1. POWER WINDOW RELAY CIRCUIT CHECK A

1. Disconnect passenger power window switch connector.

2. Turn ignition switch to ON. B
3. Check voltage between passenger power window switch harness connector D24 terminal 5(L/B) and body
ground.
C
: Battery voltage should exist.
OK or NG?
OK >> GO TO 2. D
NG >> Check harness for open or short between power window relay and driver power window switch.

2. PASSENGER POWER WINDOW CHECK E

1. Connect passenger power window switch connector.
2. Disconnect passenger power window motor connector.
F
3. Check voltage between passenger power window motor harness connector D23 terminals 1(G/B), 2(Y/G)
and body ground.

Terminal Passenger G
Voltage
power window
(+) () (Approximate values)
switch
DOWN switch H
1(G/B) Body ON 0V Battery voltage
ground
2(Y/G) UP switch ON 0V Battery voltage
GW
OK or NG?
OK >> Check harness for open or short between passenger power window switch and passenger power
window motor. J
NG >> Replace passenger power window switch

GW-17
 FRONT DOOR GLASS AND REGULATOR

FRONT DOOR GLASS AND REGULATOR PFP:80300

Removal and Installation EIS0018Y

PIIA0414E

1. Remove front door finisher. Refer to EI-19, "DOOR FINISHER" .

2. Remove sealing screen.
NOTE:
If sealing screen is reused, cut butyl tape in a way that leaves it on the sealing screen.
3. Remove lower sash mounting bolts.

PIIA0419E

4. Raise door glass to fully closed position. Pull lower sash out of
front door sash.

PIIA0420E

GW-18
 FRONT DOOR GLASS AND REGULATOR

5. Operate power window main switch to lower door glass until

door glass mounting bolts are accessible. A
6. Remove door glass mounting bolts.

PIIA0418E
D
7. While holding door glass, raise it at the rear end to pull glass out
of the sash toward the outside.
E

G
OCC3422D

8. Remove sub channel mounting nuts. H

GW

PIIA0421E
K

9. Disconnect power window motor connector.

10. Remove regulator assembly mounting bolts to remove the L
assembly out of door panel.
Install in the reverse order of removal.
M

PIIA0422E

GW-19
 FRONT DOOR GLASS AND REGULATOR

INSPECTION AFTER REMOVAL

Check regulator assembly for the following items. If a malfunction is
detected, replace or grease it.
Wire wear
Regulator deformation
Grease condition for each sliding part
NOTE:
The arrows in the figure show body grease application points.

PIIA0427J

FITTING INSPECTION
Check that the glass is securely fit into the glass run groove.
While raising and lowering the window, check for any unusual operation.

GW-20
 DOOR MIRROR

DOOR MIRROR PFP:96301

A
Removal and Installation EIS0018Z

PIIA0415E G

REMOVAL (B)
1. Remove front door trim. Refer to EI-19, "DOOR FINISHER" . H
2. Remove corner cover inner (clipped at 3 locations).
3. Remove mounting bolts to remove door outside finisher.
GW

PIIA0497E K
INSTALLATION (B)
Install in the reverse order of removal.
L

GW-21
 OUT SIDE MIRROR & UNDER MIRROR

OUT SIDE MIRROR & UNDER MIRROR PFP:96302

Removal and Installation EIS00191

PIIA0416E

GW-22
 REAR UNDER MIRROR

REAR UNDER MIRROR PFP:96340

A
Removal and Installation EIS00193

PIIA0417E G

GW

GW-23
REAR UNDER MIRROR

GW-24