SX1308 Suosemi

SX1308
85TConverter
High Efficiency 1.2MHz 2A Step Up
85T
FEATURES GENERAL DESCRIPTION

Integrated 80m Power MOSFET The SX1 308 is a constant frequency, 6-pin SOT23
2V to 24V Input Voltage current mode step-up converter intended for small,
1.2MHz Fixed Switching Frequency low power applications. The SX1308 switches at
Internal 4A Switch Current Limit 1.2MHz and allows the use of tiny, low cost
Adjustable Output Voltage capacitors and inductors 2mm or less in height.
Internal Compensation Internal soft-start results in small inrush current and
Up to 28V Output Voltage extends battery life.
Automatic Pulse Frequency Modulation The SX1308 features automatic shifting to pulse
Mode at Light Loads frequency modulation mode at light loads. The
up to 96% Efficiency SX1308 includes under-voltage lockout, current
Available in a 6-Pin SOT23-6 Package limiting, and thermal overload protection to prevent
damage in the event of an output overload. The
SX1308 is available in a small 6-pin SOT-23
APPLICATIONS package.
Battery-Powered Equipment
Set-Top Boxed
LCD Bais Supply
DSL and Cable Modems and Routers
Networking cards powered from PCI
or PCI express slots
TYPICAL APPLICATION
Efficiency
Efficiency (%)
Iout (mA)
Figure 1. Basic Application Circuit Figure 2. Efficiency Curve
Copyright 2010 by Suosemi Corporation 1

SX1308
ABSOLUTE MAXIMUM RATINGS

IN, EN voltages ... -0.3V to 26V SW Voltage ..-0.3V to 30V
Operating Temperature.... -40C to +85C Storage Temperature Range -65C to 150C
FB Voltages ................................-0.3V to 6V Peak SW Sink and Source Current 4A
Junction Temperature ...160C Lead Temperature (Soldering, 10s) ...+300C
PACKAGE/ORDER INFORMATION
SW 1 6 NC
GND 2 5 IN
FB 3 4 EN
SOT23-6
SOT23-5
(SX1308)
(MT3540)
PIN DESCRIPTION
PIN NAME FUNCTION
Power Switch Output. SW is the drain of the internal MOSFET switch. Connect the
1 SW
power inductor and output rectifier to SW. SW can swing between GND and 28V.
2 GND Ground Pin
3 FB Feedback Input. The FB voltage is 0.6V. Connect a resistor divider to FB.
Regulator On/Off Control Input. A high input at EN turns on the converter, and a
4 EN low input turns it off. When not used, connect EN to the input supply for automatic
startup.
Input Supply Pin. Must be locally bypassed.
5 IN
6 NC NC

SX1308
ELECTRICAL CHARACTERISTICS
(VIN=VEN=5V, TA = 25C, unless otherwise noted.)

Parameter Conditions MIN TYP MAX unit
Operating Input Voltage 2 24 V
Under Voltage Lockout 1.98 V
Under Voltage Lockout Hysteresis 100 mV
Current (Shutdown) VEN= 0V 0.1 1 A
Quiescent Current (PFM) VFB=0.7VNo switch 100 200 A
Quiescent Current (PWM) VFB=0.5Vswitch 1.6 2.2 mA
Switching Frequency 1.2 MHz
Maximum Duty Cycle VFB = 0V 90 %
EN Input High Voltage 1.5 V
EN Input Low Voltage 0.4 V
FB Voltage 0.588 0.6 0.612 V
FB Input Bias Current VFB = 0.6V -50 -10 nA
SW On Resistance (1) 80 150 m
SW Current Limit (1) VIN= 5V, Duty cycle=50% 4 A
SW Leakage VSW = 20V 1 A
Thermal Shutdown 155
Note:
1) Guaranteed by design, not tested.

SX1308
OPERATION
The SX1308 uses a fixed frequency, peak current The output voltage of the error amplifier the power
mode boost regulator architecture to regulate MOSFET is turned off. The voltage at the output of
voltage at the feedback pin. The operation of the the error amplifier is an amplified version of the
SX1308 can be understood by referring to the block difference between the 0.6V bandgap reference
diagram of Figure 3. At the start of each oscillator voltage and the feedback voltage. In this way the
cycle the MOSFET is turned on through the control peak current level keeps the output in regulation. If
circuitry. To prevent sub-harmonic oscillations at the feedback voltage starts to drop, the output of the
duty cycles greater than 50 percent, a stabilizing error amplifier increases. These results in more
ramp is added to the output of the current sense current to flow through the power MOSFET, thus
amplifier and the result is fed into the negative input increasing the power delivered to the output. The
of the PWM comparator. When this voltage equals SX1308 has internal soft start to limit the amount of
input current at startup and to also limit the amount
of overshoot on the output.
Figure 3. Functional Block Diagram

SX1308
TYPICAL OPERATING CHARACTERISTICS

Efficiency Curve Efficiency Curve
Current limit(A)
Efficiency
Iout (mA) Iout(mA)
line Regulation Load regualation

Vout(V)
Vout(V)
Vin (V) Iout (mA)
Freq VS Vin Efficiency VS Vin

SX1308
APPLICATION INFORMATION
Setting the Output Voltage Layout Consideration

The internal reference VREF is 0.6V (Typical).The For best performance of the SX1308, the following
output voltage is divided by a resistor divider,R1 and guidelines must be strictly followed.
R2 to the FB pin. The output voltage is given by Input and Output capacitors should be placed
R1 close to the IC and connected to ground plane
VOUT = VREF (1 + ) to reduce noise coupling.
R2
The GND should be connected to a strong
ground plane for heat sinking and noise
Inductor Selection protection.
The recommended values of inductor are 4.7 to Keep the main current traces as possible as
22H. Small size and better efficiency are the major short and wide.
concerns for portable device, such as SX1308 used SW node of DC-DC converter is with high
for mobile phone. The inductor should have low core frequency voltage swing. It should be kept at a
loss at 1.2MHz and low DCR for better efficiency. To small area.
avoid inductor saturation current rating should be Place the feedback components as close as
considered. possible to the IC and keep away from the
noisy devices.
Capacitor Selection
Input and output ceramic capacitors of 22F are
recommended for SX1308 applications. For better
voltage filtering, ceramic capacitors with low ESR
are recommended. X5R and X7R types are suitable
because of their wider voltage and temperature
ranges.
Diode Selection
Schottky diode is a good choice for SX1308
because of its low forward voltage drop and fast
reverses recovery. Using Schottky diode can get
better efficiency. The high speed rectification is also
a good characteristic of Schottky diode for high
switching frequency. Current rating of the diode must
meet the root mean square of the peak current and
output average current multiplication as following :
I D ( RMS ) I OUT I PEAK
The diode s reverse breakdown voltage should be

larger than the output voltage.

SX1308
PACKAGE DESCRIPTION
TOP VIEW RECOMMENDED LAND PATTERN
FRONT VIEW SIDE VIEW
DETAIL A
Figure 4. TSOT23-6/SOT23-6 Physical Dimensions
NOTE:
1)ALL DIMENSIONS ARE IN MILLIMETERS.
2) PACKAGE LENGTH DOES NOT INCLUDE MOLD FLASH,PROTRUSION OR GATE BURR.
3) PACKAGE WIDTH DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSION.
4) LEAD COPLANARITY (BOTTOM OF LEADS AFTER FORMING) SHALL BE 0.10 MILLIMETERS MAX.
5) DRAWING CONFORMS TO JEDEC MO-193, VARIATION AB.
6) DRAWING IS NOT TO SCALE.
7) PIN 1 IS LOWER LEFT PIN WHEN READING TOP MARK FROM LEFT TO RIGHT, (SEE EXAMPLE TOP MARK)

SX1308 Suosemi

Uploaded by

Copyright:

Available Formats

SX1308 Suosemi

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

SX1308 Suosemi

Uploaded by

Copyright:

Available Formats

SX1308

FEATURES GENERAL DESCRIPTION

Figure 1. Basic Application Circuit Figure 2. Efficiency Curve

Copyright 2010 by Suosemi Corporation 1

ABSOLUTE MAXIMUM RATINGS

PIN NAME FUNCTION

2 GND Ground Pin

3 FB Feedback Input. The FB voltage is 0.6V. Connect a resistor divider to FB.

Copyright 2010 by Suosemi Corporation 2

(VIN=VEN=5V, TA = 25C, unless otherwise noted.)

Copyright 2010 by Suosemi Corporation 3

Figure 3. Functional Block Diagram

Copyright 2010 by Suosemi Corporation 4

TYPICAL OPERATING CHARACTERISTICS

Iout (mA) Iout(mA)

line Regulation Load regualation

Vin (V) Iout (mA)

Freq VS Vin Efficiency VS Vin

Copyright 2010 by Suosemi Corporation 5

Setting the Output Voltage Layout Consideration

The diode s reverse breakdown voltage should be

Copyright 2010 by Suosemi Corporation 6

TOP VIEW RECOMMENDED LAND PATTERN

FRONT VIEW SIDE VIEW

Figure 4. TSOT23-6/SOT23-6 Physical Dimensions

Copyright 2010 by Suosemi Corporation 7

You might also like