Published by : International Journal of Engineering Research & Technology (IJERT)

http://www.ijert.org ISSN: 2278-0181

Vol. 6 Issue 02, February-2017

Generation of Electricity Through Rack and

Pinion
Laxmi Gupta Ankita Bharti
Electronics and communication Department Electronics and Communication Department
Jaypee Institute of Information Technology Jaypee Institute of Information Technology
Noida, Uttar Pradesh, India Noida, Uttar Pradesh, India

Abstract In this paper we illustrate generation of electricity shaft which is connected to the rotor of the motor. This rotor
through speed breakers. Here we used a technique of harvesting contains a magnet which when turned produce rotating
energy by three mechanisms- Rack and pinion mechanism, magnetic field which in turn produces electromotive force.
Crank and shaft mechanism, Roller mechanism. In this paper The rotor is surrounded by stator which is nothing only a
we have used roller mechanism. This technique is beneficial to
stationary case, which contains the wound copper coils or
those areas where generation of electricity is a difficult task.
When a vehicle moves over the speed breakers its kinetic energy windings. When the moving magnetic field passes through
which is due its speed, friction between road and its wheels, heat these wound copper coil or windings, they generate
developed during motion and energy of wind striking is given to electricity. On controlling the speed at which the rotor is
roller attached beneath it. Then the roller passes the energy to turned, a steady flow of electricity is produced in the
spring and spring passes it to dynamo which converts windings. These windings of the rotor are connected to the
mechanical energy to electrical energy. This electrical energy is electrical network by transmission lines. This concept it is
in the form of DC and we used inverter which converts DC into known as "reciprocating bump". The speed breaker designed
AC. Large amount of electricity can be generated saving lot of such that it is supported on springs. When a vehicle mounts
money and if implemented will be very beneficial for
on the speed breaker, the load on the springs causes a
Government.
movement which is converted to a rotary motion by using the
Keywords Component; Formatting; Style; Styling; Insert rack and pinion mechanism. Hence the energy is generated
and can be stored in batteries or any other equippments. The
I. INTRODUCTION input for producing energy is the weight of the vehicle.
In India many of the people are facing with the problem of motion to a DC motor for electricity generation.
electricity. Of those who did their effort all find electricity
supply intermittent and unreliable. In India there is lack of II. EXPERIMENTAL SETUP
clean and reliable energy sources such as electricity. About An iron roller is fixed beneath wooden ramp on
1000 million people in India are still using traditional which vehicle passes. As vehicle goes over it starts moving.
biomass energy sources such as fuel wood, agricultural waste A connection is attached which transfer the motion to a DC
and livestock dung for cooking and other domestic needs. motor for electricity generation. This is a new concept
This traditional fuel combustion in India causes air pollution undergoing research. The number of vehicles on road is
which causes about 500,000 deaths per year and other chronic increasing rapidly and if we convert kinetic energy of
health diseases. vehicles into the rotational motion of roller which is
Carbon dioxide (CO2) produces from India thermal power converted into electricity. This is the main concept of this
plant is about 50 to 120 percent more than that carbon paper. In this paper, a roller is fixed in between a speed
dioxide is produce in European union countries (EU-27) from breaker and there is a type of grip provided on the speed
coal-fired, oil-fired and natural gas-fired thermal power breaker so that when a vehicle passes over speed breaker it
plants. rotates the roller. By the movement of roller we can rotate the
The largest problem of electricity in India was seen on July shaft of D.C. generator by the chain drive which provides 1:5
2012. In history in July 2012 India blackout was the largest speed ratios. As the shaft of D.C. generator rotates, it
power outage due to occurring of two events on 30 and 31 produces electricity. Battery is used to store electricity. This
July 2012. This outage of power affected 700 million people electricity is used to glow street lamps. During daytime we
which is about 9% population of the world or half of India's dont require to lighten up the street lamps. So we are
population, spread across 22 states in Northern, Eastern, and controlling this operation using a switch which is connected
Northeast India. During this event of outage power approx to the battery through a wire. A car or any heavy vehicle
32giga watts of generating capacity was taken offline. moving with a speed of 100 mph and passing over this roller
According to an article given in The Wall Street Journal attached to the road then this roller moves with 90 mph (due
which stated that, 320 million initially had power, while the to losses). So a cycle is coming with a speed of 20 mph and
rest of the affected population lacked direct access of the total passes this roller (which is moving at a speed of 90 mph).
affected people. [1] There will be a collision because of difference in the speed.
In this paper roller is directly connected to mechanical This is the main reason for using speed breakers. A
arrangement which consist of chain & sprocket & rack & connection is provided which transfer the motion to a DC
pinion. This mechanical arrangement is directly connected to

IJERTV6IS020056 www.ijert.org 109

(This work is licensed under a Creative Commons Attribution 4.0 International License.)
Published by : International Journal of Engineering Research & Technology (IJERT)
http://www.ijert.org ISSN: 2278-0181
Vol. 6 Issue 02, February-2017

alternator for electricity generation. The set up for the

experiment is given in Fig.1

Fig.1. Experimental Setup

Fig.4 Alternator

III. CALCULATION AND RESULTS

This paper proposed a technique where a roller is fixed in
between a speed breaker and there is a type of grip
provided on the speed breaker so that when a vehicle
passes over speed breaker it rotates the roller. By the
Fig.2 Proposed Block Diagram movement of roller we can rotate the shaft of D.C.
generator when shaft of generator rotates then it generates
electricity by the following formulas:-The following
Equipments used are described as follows. The rack and performance characteristics is shown in fig.6.
pinion is used to convert between rotational motions into P=TxS
linear motion. The rack is flat and gear has the teeth which is Where: T is torque generated by dynamometer
called pinion. Rack and pinion can convert from between S is the shaft speed
rotational and linear motion. Here motion is converted with T=FxD
speed gain. Chain & sprocket arrangement uses a gear of 24 Where: F is friction force due to rotation of shaft
teeth (a pair) connected with the chain which is used to D is the distance of shaft from the pivot
increase revolution per minute (rpm). Full wave bridge F = aV2 + b
rectifier uses four diodes (IN4007) as shown in Fig.3.It is Where: a is coefficient for two wheel vehicle
preferred over centre tapped rectifier because of three b is reference weight of vehicle in k.g
reasons. First it is less costly than centre tapped. Secondly it
has peak inverse voltage half of centre tapped. It also
prohibits back flow of power from alternator to battery. An
alternator which is dynamo without commutator is used to Performance specifications
convert mechanical energy to electrical energy. Alternator
5
with a stationary armature in a rotating magnetic field is used 4
as shown in Fig.4. 3
2
1
0
15 20 25 30
Current (mA) 0.25 0.97 2.03 3.11
Voltage (V) 2.0825 2.776 3.47 4.164
Power(W) 0.17658 0.23544 0.2943 0.35316

Fig.3 Half wave bridge rectifier

IJERTV6IS020056 www.ijert.org 110

(This work is licensed under a Creative Commons Attribution 4.0 International License.)
 Published by : International Journal of Engineering Research & Technology (IJERT)
http://www.ijert.org ISSN: 2278-0181
Vol. 6 Issue 02, February-2017

IV. CONCLUSION
This type of electricity generation helps us in saving our
conventional resources as it generates electricity through
renewable natural resources which are easily available. By
this method electricity can be generated without depending
on other factors and can meet high demands of future. It is
also environment friendly process. There is also no where
obstruction in traffic flows. It is automatic and no need of
man power resource in this. This has application in many
areas such as street lights and traffic lights which stop
accidents from happening. "Electricity plays a very important
role in our life. As the population of india is increasing day
by day, the electricity generation has become a major issue
and it does not fulfill the requirements of people. In this paper
we described about a technology to generate electricity from
speed breakers which is reliable and will help in conserving
our natural resources

V. ACKNOWLEDGEMENT
The authors are grateful to Jaypee Institute Of Information
Technology for providing resources at the department of
Electronic and Communication Engineering to enable them to
carry out this research work.

REFERENCES
[1] Abhishek Gupta, N. M. (2016). Electricity Generation from Speed
Breakers. International Journal of Electrical and Electronics Research
, 135-139.
[2] Mohamad Ramadan, M. K. (2015). Using speed bump for power
generation Experimental study. The 7th International Conference on
Applied Energy ICAE2015 (pp. 867-872). Paris: Elsevier Ltd.

IJERTV6IS020056 www.ijert.org 111

(This work is licensed under a Creative Commons Attribution 4.0 International License.)