www.fairchildsemi.

com

KA5x02xx-SERIES
KA5H0265RC, KA5M0265R, KA5L0265R,
KA5H02659RN/KA5M02659RN, KA5H0280R,
KA5M0280R
Fairchild Power Switch(FPS)
Features Description
Precision Fixed Operating Frequency (100/67/50kHz) The Fairchild Power Switch(FPS) product family is specially
Low Start-up Current (Typ. 100uA) designed for an off-line SMPS with minimal external
Pulse by Pulse Current Limiting components. The Fairchild Power Switch(FPS) consist of high
Over Load Protection voltage power SenseFET and current mode PWM IC. Included
Over Voltage Protection (Min. 25V) PWM controller features integrated fixed oscillator, under
Internal Thermal Shutdown Function voltage lock out, leading edge blanking, optimized gate turn-on/
Under Voltage Lockout turn-off driver, thermal shut down protection, over voltage
Internal High Voltage Sense FET protection, and temperature compensated precision current
Auto-Restart Mode sources for loop compensation and fault protection circuitry-
compared to discrete MOSFET and controller or RCC
switching converter solution. The Fairchild Power Switch(FPS)
can reduce total component count, design size, weight and at the
same time increase efficiency, productivity, and system
reliability. It has a basic platform well suited for cost-effective
design in either a flyback converter or a forward converter.
TO-220F-4L 8-DIP TO220-5L

1
1 1
1.6.7.8. Drain 1. Drain
1. GND
2. GND 2. GND
2. Drain
3. Vcc 3. Vcc
3. Vcc
4. FB 4. FB
4. FB
5. NC 5. S/S

Internal Block Diagram

VCC
32V 5V Internal DRAIN
Vref bias SFET
Good
logic
* Soft Start
OSC
5V
S
uA Q
R
FB
L.E.B
5A 1mA 2.5R +
9V 1R
0.1V
+
7.5V S GND
Q
R
+ Thermal S/D
27V Power on reset
OVER VOLTAGE S/D

* KA5H0265RC

Rev.1.0.4
2003 Fairchild Semiconductor Corporation
KA5X02XX-SERIES

Absolute Maximum Ratings

(Ta=25C, unless otherwise specified)

Characteristic Symbol Value Unit

KA5x0265xRx
Drain-Gate Voltage (RGS=1M) VDGR 650 V
Gate-Source (GND) Voltage VGS 30 V
(1)
Drain Current Pulsed IDM 8.0 ADC
Continuous Drain Current (TC=25C) ID 2.0 ADC
Continuous Drain Current (TC=100C) ID 1.3 ADC
(2)
Single Pulsed Avalanche Energy EAS 68 mJ
Maximum Supply Voltage VCC,MAX 30 V
Analog Input Voltage Range VFB -0.3 to VSD V
PD 42 W
Total Power Dissipation
Darting 0.33 W/C
Operating Junction Temperature. TJ +160 C
Operating Ambient Temperature. TA -25 to +85 C
Storage Temperature Range. TSTG -55 to +150 C
KA5x0280R
Drain-Gate Voltage (RGS=1M) VDGR 800 V
Gate-Source (GND) Voltage VGS 30 V
(1)
Drain Current Pulsed IDM 8.0 ADC
Continuous Drain Current (TC=25C) ID 2.0 ADC
Continuous Drain Current (TC=100C) ID 1.3 ADC
(2)
Single Pulsed Avalanche Energy EAS 90 mJ
Maximum Supply Voltage VCC,MAX 30 V
Analog Input Voltage Range VFB -0.3 to VSD V
PD 35 W
Total Power Dissipation
Darting 0.28 W/C
Operating Junction Temperature. TJ +160 C
Operating Ambient Temperature. TA -25 to +85 C
Storage Temperature Range. TSTG -55 to +150 C

Note:
1. Repetitive rating: Pulse width limited by maximum junction temperature
2. L = 51mH, starting Tj = 25C

2
 KA5X02XX-SERIES

Electrical Characteristics (SFET Part)

(Ta=25C unless otherwise specified)

Parameter Symbol Condition Min. Typ. Max. Unit

KA5x0265xRx
Drain-Source Breakdown Voltage BVDSS VGS=0V, ID=50A 650 - - V
VDS=Max. Rating, VGS=0V - - 50 A
Zero Gate Voltage Drain Current IDSS VDS=0.8Max. Rating,
- - 200 A
VGS=0V, TC=125C
Static Drain-Source on Resistance (Note) RDS(ON) VGS=10V, ID=0.5A - 5.0 6.0
(Note)
Forward Transconductance gfs VDS=50V, ID=0.5A 1.5 2.5 - S
Input Capacitance Ciss - 550 -
VGS=0V, VDS=25V,
Output Capacitance Coss - 38 - pF
f=1MHz
Reverse Transfer Capacitance Crss - 17 -
Turn on Delay Time td(on) - 20 -
VDD=0.5B VDSS, ID=1.0A
Rise Time tr (MOSFET switching time is - 15 -
nS
Turn Off Delay Time td(off) essentially independent of - 55 -
operating temperature)
Fall Time tf - 25 -
Total Gate Charge VGS=10V, ID=1.0A,
Qg - - 35
(Gate-Source+Gate-Drain) VDS=0.5B VDSS (MOSFET
Gate-Source Charge Qgs switching time is essentially - 3 - nC
independent of operating
Gate-Drain (Miller) Charge Qgd temperature) - 12 -

KA5x0280R
Drain-Source Breakdown Voltage BVDSS VGS=0V, ID=50A 800 - - V
VDS=Max. Rating, VGS=0V - - 50 A
Zero Gate Voltage Drain Current IDSS VDS=0.8Max. Rating,
- - 200 A
VGS=0V, TC=125C
Static Drain-Source on Resistance (Note) RDS(ON) VGS=10V, ID=0.5A - 5.6 7.0
Forward Transconductance (Note) gfs VDS=50V, ID=0.5A 1.5 2.5 - S
Input Capacitance Ciss - 250 -
VGS=0V, VDS=25V,
Output Capacitance Coss - 52 - pF
f=1MHz
Reverse Transfer Capacitance Crss - 25 -
Turn on Delay Time td(on) - 21 -
VDD=0.5B VDSS, ID=1.0A
Rise Time tr (MOSFET switching time is - 28 -
nS
Turn Off Delay Time td(off) essentially independent of - 77 -
operating temperature)
Fall Time tf - 24 -
Total Gate Charge VGS=10V, ID=1.0A,
Qg - - 60
(Gate-Source+Gate-Drain) VDS=0.5B VDSS (MOSFET
Gate-Source Charge Qgs switching time is essentially - 15 - nC
independent of operating
Gate-Drain (Miller) Charge Qgd temperature) - 20 -

Note:
1. Pulse test: Pulse width 300S, duty cycle 2%
2. S = ---
1
-
R

3
KA5X02XX-SERIES

Electrical Characteristics (Control Part) (Continued)

(Ta=25C unless otherwise specified)

Parameter Symbol Condition Min. Typ. Max. Unit

UVLO SECTION
Start Threshold Voltage VSTART VFB=GND 14 15 16 V
Stop Threshold Voltage VSTOP VFB=GND 8.2 8.8 9.4 V
OSCILLATOR SECTION
KA5H0265xRx
Initial Accuracy FOSC 90 100 110 kHz
KA5H0280R
KA5M0265xRx
Initial Accuracy FOSC 61 67 73 kHz
KA5M0280R
Initial Accuracy FOSC KA5L0265R 45 50 55 kHz
Frequency Change With Temperature (2) F/T -25C Ta +85C - 5 10 %
KA5H0265xRx
Maximum Duty Cycle Dmax 62 67 72 %
KA5H0280R
KA5M0265xRx
Maximum Duty Cycle Dmax KA5M0280R 72 77 82 %
KA5L0265R
FEEDBACK SECTION
Feedback Source Current IFB Ta=25C, 0V Vfb 3V 0.7 0.9 1.1 mA
Shutdown Feedback Voltage VSD Vfb 6.5V 6.9 7.5 8.1 V
Shutdown Delay Current Idelay Ta=25C, 5V Vfb VSD 4 5 6 A
SOFT START SECTION
Soft Start Voltage VSS 4.7 5.0 5.3 V
KA5H0265RC
Soft Start Current ISS 0.8 1.0 1.2 mA
REFERENCE SECTION
Output Voltage (1) Vref Ta=25C 4.80 5.00 5.20 V
Temperature Stability (1)(2)
Vref/T -25C Ta +85C - 0.3 0.6 mV/C
CURRENT LIMIT(SELF-PROTECTION)SECTION
Peak Current Limit IOVER KA5x02659RN 0.79 0.9 1.01 A
KA5x0265Rx
Peak Current Limit IOVER 1.05 1.2 1.34 A
KA5x0280R
PROTECTION SECTION
Over Voltage Protection VOVP VCC 24V 25 27 29 V
Thermal Shutdown Temperature (1)
TSD - 140 160 - C
TOTAL DEVICE SECTION
Start-up Current ISTART VCC=14V - 100 170 A
Operating Supply Current
IOPR VCC 28 - 7 12 mA
(Control Part Only)

Note:
1. These parameters, although guaranteed, are not 100% tested in production
2. These parameters, although guaranteed, are tested in EDS (wafer test) process

4
 KA5X02XX-SERIES

Typical Performance Characteristics

(These characteristic graphs are normalized at Ta=25C)

Fig.1 Operating Frequency Fig.2 Feedback Source Current

1.2 1.2
1.15 1.15
1.1 1.1
1.05 1.05
Fosc 1 Ifb 1
0.95 0.95
0.9 0.9
0.85 0.85
0.8 0.8
-25 0 25 50 75 100 125 150 -25 0 25 50 75 100 125 150
Temperature [C] Temperature [C]

Figure 1. Operating Frequency Figure 2. Feedback Source Current

Fig.3 Operating Current Fig.4 Max Inductor Current

1.2 1.1
1.15 1.05
1.1
1.05 IIpeak
over 1
Iop 1 0.95
0.95 0.9
0.9
0.85 0.85
0.8 0.8
-25 0 25 50 75 100 125 150 -25 0 25 50 75 100 125 150
Temperature [C] Temperature [C]

Figure 3. Operating Supply Current Figure 4. Peak Current Limit

Fig.5 Start up Current Fig.6 Start Threshold Voltage

1.5 1.15
1.3 1.1
1.05
1.1
Istart Vstart 1
0.9
0.95
0.7 0.9
0.5 0.85
-25 0 25 50 75 100 125 150 -25 0 25 50 75 100 125 150
Temperature [C] Temperature [C]

Figure 5. Start up Current Figure 6. Start Threshold Voltage

5
KA5X02XX-SERIES

Typical Performance Characteristics (Continued)

(These characteristic graphs are normalized at Ta=25C)

Fig.7 Stop Threshold Voltage Fig.8 Maximum Duty Cycle

1.15 1.15
1.1 1.1
1.05 1.05
Vstop 1 Dmax 1
0.95 0.95
0.9 0.9
0.85 0.85
-25 0 25 50 75 100 125 150 -25 0 25 50 75 100 125 150
Temperature [C] Temperature [C]

Figure 7. Stop Threshold Voltage Figure 8. Maximum Duty Cycle

Fig.9 Vcc Zener Voltage Fig.10 Shutdown Feedback Voltage

1.2 1.15
1.15 1.1
1.1
1.05 1.05
Vz 1 Vsd 1
0.95 0.95
0.9
0.85 0.9
0.8 0.85
-25 0 25 50 75 100 125 150 -25 0 25 50 75 100 125 150
Temperature [C] Temperature [C]

Figure 9. VCC Zener Voltage Figure 10. Shutdown Feedback Voltage

Fig.11 Shutdown Delay Current Fig.12 Over Voltage Protection

1.2 1.15
1.15
1.1
1.1
1.05 1.05
Idelay 1 Vovp 1
0.95 0.95
0.9
0.85 0.9
0.8 0.85
-25 0 25 50 75 100 125 150 -25 0 25 50 75 100 125 150
Temperature [C] Temperature [C]

Figure 11. Shutdown Delay Current Figure 12. Over Voltage Protection

6
 KA5X02XX-SERIES

Typical Performance Characteristics (Continued)

(These characteristic graphs are normalized at Ta=25C)

Fig.13 Soft Start Voltage Fig.14 Drain Source Turn-on

1.15 Resistance
1.1 2.5
1.05 2
Vss 1 1.5
0.95 Rdson
( )1
0.9 0.5
0.85 0
-25 0 25 50 75 100 125 150 -25 0 25 50 75 100 125 150
Temperature [C] Temperature [C]

Figure13. Soft Start Voltage Figure 14. Static Drain-Source on Resistance

7
KA5X02XX-SERIES

Package Dimensions

TO-220F-4L

8
 KA5X02XX-SERIES

Package Dimensions (Continued)

TO-220F-4L(Forming)

9
KA5X02XX-SERIES

Package Dimensions (Continued)

8-DIP

10
 KA5X02XX-SERIES

Package Dimensions (Continued)

TO-220-5L

11
KA5X02XX-SERIES

Package Dimensions (Continued)

TO-220-5L(Forming)

12
 KA5X02XX-SERIES

Ordering Information
Product Number Package Marking Code BVDSS FOSC RDS(on)
KA5H0265RCTU TO-220-5L
5H0265RC 650V 100kHz 5
KA5H0265RCYDTU TO-220-5L(Forming)
KA5M0265RTU TO-220F-4L
5M0265R 650V 67kHz 5
KA5M0265RYDTU TO-220F-4L(Forming)
KA5L0265RTU TO-220F-4L
5L0265R 650V 50kHz 5
KA5L0265RYDTU TO-220F-4L(Forming)
Product Number Package Marking Code BVDSS FOSC RDS(on)
KA5H0280RTU TO-220F-4L
5H0280R 800V 100kHz 5.6
KA5H0280RYDTU TO-220F-4L(Forming)
KA5M0280RTU TO-220F-4L
5M0280R 800V 67kHz 5.6
KA5M0280RYDTU TO-220F-4L(Forming)
Product Number Package Marking Code BVDSS FOSC RDS(on)
KA5H02659RN 8-DIP 5H02659R 650V 100kHz 5
KA5M02659RN 8-DIP 5M02659R 650V 67kHz 5
TU : Non Forming Type
YDTU : Forming Type

13
KA5X02XX-SERIES

DISCLAIMER
FAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY
PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION OR DESIGN. FAIRCHILD DOES NOT ASSUME ANY
LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCT OR CIRCUIT DESCRIBED HEREIN; NEITHER
DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS.

LIFE SUPPORT POLICY

FAIRCHILDS PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES
OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF FAIRCHILD SEMICONDUCTOR
CORPORATION. As used herein:
1. Life support devices or systems are devices or systems 2. A critical component in any component of a life support
which, (a) are intended for surgical implant into the body, device or system whose failure to perform can be
or (b) support or sustain life, and (c) whose failure to reasonably expected to cause the failure of the life support
perform when properly used in accordance with device or system, or to affect its safety or effectiveness.
instructions for use provided in the labeling, can be
reasonably expected to result in a significant injury of the
user.

www.fairchildsemi.com

8/25/03 0.0m 001

Stock#DSxxxxxxxx
2003 Fairchild Semiconductor Corporation