Carriage of Steel Cargoes, Guidelines

1(49)
Carriage of steel cargoes - Index

Guidelines for Members, Masters and Surveyors
CONTENTS
INTRODUCTION
PART 1 TYPES OF STEEL CARGOES
Category A - Packed or wrapped

Category B - Not packed or wrapped
PART 2 CARGO CARE
Section 1 - Loading and stowage
Planning
Loading wet cargo
Rain during loading
Incompatible cargoes
Strength of tank tops
Stowage and lashing of different types of products
o Steel coils
o Steel slabs
o Hot and cold rolled steel in packages and bundles
o Single plates
o Structural steel
o Sheet pilings
o Pipes
o Wire rods
o Stowage certificates
The golden rules of stowage
Section 2 - On the voyage
Supervision of loading, stowing and discharging

Maintenance of the vessel
Watertightness Ventilation Ventilation Ventilation
Ventilation
2(49)
PART 3 SURVEYS
Section 1 - Pre-shipment survey - cargo
Information for the Surveyor

When to instruct the Surveyor
The Surveyor's duties
Preliminary report
Final report
Section 2 - Pre-shipment survey - the vessel
Cargo holds
Steel hatch covers and other deck openings
Checklist
o General
o Panels
o Rubber packing (gaskets)
o Retaining channels
o Compression bars
o (a) Transverse guttering and (b) Hatch rims
o Steel to steel contact points
o Snugs
o Crutches
o Quick-Acting cleats, rods, nuts and washers/Other cleating
arrangements
o Cross wedges (cross joint cleats)
o Inboard drainage system
o Wheel tracks (guide rails)
o Wheels
o (a) Panel side chains (b) Hinges (c) Hydraulics
o Access hatches
o Access doors
o Bilge sounding caps
o Sealing tape
Testing for watertightness
o Ultrasonic test
o Hose test
o Chalk test
The survey report
o Preliminary report
o Final report
3(49)
Section 3 - Discharge survey
Instructions to Surveyor
The survey
o Copy documents which should be obtained
Contents of the Surveyor's report - Relative to the cause of any damage
o Non-return valves on Bilge Lines
o Tank tops
The survey report
o Preliminary
o Final
Stevedores' outturn report
Who should be authorised to board the vessel and examine the cargo?
Section 4 - Cargo/commodity survey
The survey
The survey report
o Preliminary
o Final
Silver nitrate testing and sampling
PART 4 THE BILL OF LADING
Section 1 - The legal position
A "clean" Bill of Lading

Letters of Indemnity
Claused Bills of Lading
Section 2 - Cargo condition clauses
o "Rust stained"
o "Partly rust stained"
o "Rusty"
o "Partly rusty"
o "Rust spots apparent"
o "Rust spotted"
o "Wet before shipment"
o "Rust with pitting"
o "Covered with snow"
o "Areas of steel surfaces reacting to silver nitrate solution tests"
o "Stained by an Unidentifiable Powder"
o streaks"
4(49)
Mechanical (handling) damages

o Unwrapped material
o Hot rolled steel sheeting in coils
o Hot rolled steel plates in bundles
o Single steel plates
o Large steel beams
o Merchant iron
o Pipes and tubes
Wire rods
o Unwrapped goods
o Wrapped goods
o Sheet pilings
Wrapped material
o Steel coils
o Packages
General "Rust streaked" "Evidence of contact with free moisture - drip down rust
PART 5 RESPONSIBILITIES UNDER CHARTERPARTIES
Types of contracts
The owner's obligations under the Hague or Hague-Visby Rules
Loading, stowage and discharging operations
o Time Charterparties
o The NYPE Inter-Club Agreement
o Voyage Charterparties
Conclusion
5(49)
Introduction
As part of the service offered to Members of Skuld, the Club operates a

loss prevention programme. The pupose of this programme is to help
Members reduce claims and to offer advice aimed at improving safety and
efficiency of vessels entered with the Club. Most importantly, the Club
works together with Members to help safeguard the lives of those working
for and alongside them. It is in this spirit that the Club offers the guidance
in this booklet.
This booklet is not a scientific study of the physics and chemistry of steel,
nor is it a legal textbook. It has been prepared with one aim in mind: to
be a useful, handy reference guide for members, their Masters and
Officers, and for Surveyors appointed on their behalf. It is intended to be
a practical guide for use on the quayside, or on the bridge, or on the deck,
or in the Member's office.
This booklet has a number of objectives. The first is to reduce the risk of
actual damage to cargo whilst in the Member's custody. Damage is not
bound to happen. It can and will be avoided in the vast majority of cases
if the cargo is handled, stowed and carried in the right way. This is good
for the Member concerned and for all the Club's Members.
A second objective is to help Members protect themselves from financial

penalties resulting from circumstances outside their control, but for which
they may be legally liable. The classic example is pre-shipment damage to
cargo. A Master may oversee loading and stowage in an exemplary
fashion on board a perfect ship, carry and discharge the cargo in
accordance with best practice, without incident, and yet still find his
Owners unable to defend a substantial cargo damage claim. The cargo
was not in good condition when loaded, but the Bills of Lading were not
claused. It is not enough for the Master to do his job - he has to find ways
to protect himself from those who do not. Often this involves getting the
paperwork right. It is a chore, and there are no doubt many other
pressures competing for the Master's time and energy, but it is essential.
The good news is that the Master is not on his own. The Club, its
Correspondents, Surveyors and lawyers are all there to assist - this
booklet is also intended to help.
As well as the prevention of cargo claims and cargo damage on board (not
always the same thing, as members may know to their cost), these
guidelines are intended to help Masters and Members improve safety and
efficiency on board. Correct handling of steel products, based on an
awareness of the particular characteristics and possible hazards of
6(49)
different types of products, makes life safer for stevedores and crew.
Accidents equal claims, so correct handling methods make sense all
round. Correct stowage not only reduces the risk of cargo damage by
protecting the cargo, it also protects the vessel from the cargo, which in
the case of steel should be a major concern. This booklet contains
guidelines on these subjects which ought to be followed not only in order
to reduce the chance of cargo damage claims, but by all those who value
their vessel and their own safety.
This booklet also offers guidance to the Surveyors who may be called
upon to survey cargo and/or ship at one or other stage in the adventure.
The Club and its Members value Surveyors not as passive recorders of
information, but as a vital part of the Member's loss prevention team.
They are encouraged to see their role in this way and the advice and
assistance they can offer to Masters is an essential part of their work.
Many are experts in this field. The Club hopes that even for experts, this
booklet will prove to be useful as a source of advice, as an aide memoire
and as a back-up when differences of opinion arise, as they often do.
For ease of reference, the booklet is divided into sections, some of which
may appear to be of more or less interest, depending on the user's role.
But the issues involved are inter-connected. They cannot be read in
splendid isolation - the guidelines for surveys, for example, should be
useful for Surveyors, but the information they contain is of direct interest
to Masters.
The Club hopes that the guidelines in this booklet prove to be of practical
use to all those involved with the carriage of steel cargoes on members'
vessels.
We express our thanks to Arthur Sparks, of Sparks & Company Ltd.,

London, who has contributed in respect of the technical issues, and to
Glenn Winter and Duncan Rudkin, Holmes Hardingham, solicitors, London,
who have contributed in respect of the legal aspects in this publication.
All previous steel circulars are superseded by this publication.
Oslo - January 1998
Hans Jrgensen
7(49)
PART 1 TYPES OF STEEL CARGOES
Steel cargoes can be split into two categories: products that are packed or
wrapped and those that are not.
Category A - Packed or wrapped

- Special quality wire rods in coil form; for example, pre-stressing wire,
tyre cord, high tensile wire rods. This type of wire rod is usually wrapped
in strong waterproofed reinforced material.
- Cold rolled steel sheeting in coils and packages.
- Coated steel in coils and packages; for example galvanised, aluminised

and paint-coated.
- Tin plate in steel boxes - also shipped in coils on wooden skids. These
products are usually wrapped in plastic coated kraft paper, with an outer
layer of steel sheet wrapper. The bundles are then secured with flat metal
strapping bands.
Packing is designed to protect the products from handling damage and

from the atmosphere and to keep bundles together. It is not airtight or
watertight.
Category B - Not packed or wrapped

- Structural steels; for example beams, angles, flats, channels, reinforcing
bars, squares, rounds. Usually shipped in 20 or 40 feet (6 metre and 12
metre) bundles, secured by wire bands or strapping bands.
- Single flat steel plates and bundles of steel plates secured with strapping
bands.
- Hot rolled steel sheeting in coils and bundles, secured with metal
strapping bands.
- Steel slabs, billets, blooms, mild steel hot rolled wire rods.
- Scrap: ferrous metal, borings, shavings, turnings,

cuttings, iron swarf, steel swarf. Scrap metal can heat
spontaneously leading to fire. This is because it has a
high surface area for its mass, making oxidation easy.
Vibrations and working of the vessel causes friction and
therefore heating. Masters are advised to familiarise
themselves with the special dangers presented by scrap
metal, before carrying it. If in doubt the local Skuld
Correspondents should be consulted.
8(49)
A few guidelines:
- Care should be taken over ventilation.
- Cargo which was wet before loading is more likely to heat in transit.
- Scrap metal must not be allowed to come into contact with sea water.
- Check the temperature of the bulk ashore, before loading: if it is

increasing, consider rejecting the cargo.
- If the surface temperature of the bulk reaches 80C at sea and shows no
sign of cooling, there is a real risk of fire. Consider diverting to a suitable
port of refuge.
- Cargo should be loaded, segregated, stowed and carried in accordance

with the latest edition of the IMO Code of Safe Practice for Solid Bulk
Cargoes (BC Code).
9(49)
Carriage of steel cargoes - Part 2 Cargo Care
SECTION 1 - LOADING AND STOWAGE
Planning
It is important not to allow loading to begin before a stowage plan is agreed.
Stevedores may be in a hurry to start. They might have to wait, but by approving the
stowage plan before the beginning of loading, the Master can avoid worse delays
later and prevent damage to cargo, his ship and the lives of those on board.
If a Surveyor is attending, he should assist and advise the Master in checking the
stowage plan.
Loading wet cargo

Wet cargo in a ship's holds increases humidity in the air and vapour pressure. The
presence of wet cargo in the holds will therefore lead to moisture damage to cargo
that was sound and dry on shipment.
Rain during loading

Category A packed or wrapped products must not be left uncovered on the quay or
loaded during rain.
Category B non-packed or non-wrapped products will often be stored on the open

quay and loaded during light rain. This is usually acceptable provided they are not
going into the same hold as dry products.
A suitable descriptive clause (for example "Wet before Shipment") should be

prepared for insertion on Mate's Receipts and Bills of Lading for any wet cargo.
Watch out for coils that appear to be dry on the outside but which drip water from the
windings when lifted.
Hatch covers and all other deck openings should be closed in good time to stop rain
getting to cargo in the holds.
A careful note of the timing of any rain and of the opening and closing of hatch
covers should be made so that the Master can check that the timings in the
Statement of Facts presented to him for signature match the timings in the ship's log.
Incompatible cargoes
Care should be taken not to load incompatible cargoes (such as chemicals, fertilisers,
sulphur-bearing materials and, in many instances, hygroscopic cargoes) in the same
compartment as steel cargo.
10(49)
Strength of tank tops

Bundles of reinforcing bars and bundles of small scantling materials can be stowed in
tween decks. Unpalletised steel coils must never be stowed in tween decks. The
ideal stowage position for steel products is in the bottom of the vessel, on the tank
tops.
Steel is a high density, deadweight cargo. The danger of tank top overload must be
considered and avoided. The Master should calculate the permissible tonnage and
this figure should never be exceeded.
The permissible tonnage is calculated as follows:

Area of tank top (M2) x Tonnes per M2 tank top strength limitation.
The tank top strength limitation figure is supplied by the shipbuilder and approved by
the Classification Society. The figure usually remains unchanged throughout a ship's
life. The strength of the scantlings of the component parts of a ship reduces over the
years. The older the ship, the more caution should be exercised in calculating the
permissible tonnage - a greater safety margin should be left for older vessels.
If the permissible tonnage is exceeded, the tank top plating may be deformed. In
order to spread the pressure evenly over the tank top and thereby reduce structural
deformation, dunnage should be adequately spread, this to avoid spot overloading
Stowage and lashing of different types of products
Steel coils
In coils of up to 15 tons, the tank top should be dunnaged with two double lines of
6"x1" (15cm x 2.5cm) dunnage wood boards. For coils of over 15 tons, three lines of
such dunnage should be used. In order to achieve tight stowage and prevent
movement, wooden chocks must be inserted on top of the lines of dunnage in the
lower tier.
For handling steel coils, chains and wire rope slings should never be used. The
safest lifting gear is a round steel pole through the centre of the coil, or a "C" hook.
The correct method of stowing hot and cold rolled steel coils (except for palletised
coils) is usually with their centre cores fore and aft. If they are stowed any other way,
they are more likely to shift. Steel coils must never be stowed in tween decks, except
for palletised coils in special circumstances.
If it can be avoided, coils should not be stowed in a single tier, unless they are
overstowed with other cargo. If there are only enough coils for a single tier and
nothing can be placed on top, an ideal stowage would be to stow the coils in two tiers
at the after end of the compartment. If single tier stowage cannot be avoided, each
athwartship tier must be secured with a locking coil.
11(49)
As a general guide, the following weight/height ratio should be applied -
10 ton coils: 3 high

15 ton coils: 2 high
15+ ton coils: 1 high
The age of the vessel and strength of the tank tops should be considered, and a
lower ratio applied if appropriate to a particular vessel.
No. 1 Hot rolled steel coil provided with No. 2 Cold rolled steel coil
steel channels to prevent edge damage.
Begin stowage against the end bulkhead in the centre and the wings, with the gap
between the wing and centre stowage closing to leave a space for the insertion of
locking coils. The stow should be arranged so that the second tier locking coils do not
protrude down into the cantlines of the lower tier by more than one-third of the
diameter of the locking coil.
Ideally, the athwartships lines of cargo should extend out to the extremities of the
cargo hold. If stevedores are not equipped with the necessary gear to do this in the
upper tiers, a mobile crane can be used to put the outer coils in place.
Drawings "A" and "B" (see next page) and photographs "3" and "4" show the
recommended method of securing with strapping bands. Passing bands through the
cores of adjacent coils prevents fore and aft movement. Crossing bands over the top
of coils prevent up and down movements, when the ship is pitching. This method also
stops individual coils from turning in stow.
When you have a single tier, the locking coil should be secured as shown in drawing
"C".
Steel strapping bands should always be tightened with pneumatic tools never by
hand operated tools. The ends of the securing bands should always be joined with
two crimp seals.
Metal strapping bands should ideally be used to secure steel coils, for the following
reasons:
- Each coil can be efficiently secured through its core to the two coils beneath - costly
perhaps, but the safest method.
- Using a pneumatic tightening tool, bands are tensioned up to 2,000 kgs.
12(49)
- Bands are applied singly, making it easier to handle them and pass them through
awkward gaps.
- Tension is uniform throughout the stow. (Do not use securing timbers, which defeat
this purpose.)
If wire rope is to be used to secure steel coils, the following precautions should be
taken:-
- All bulldog grips should be properly fitted and adequately tightened.
- Three bulldog grips should be fitted either side of the spanscrew.
- The turnbuckles should be extended to the maximum of thread before application of
the wires in order to ensure that after tightening not more than 1/3 of the thread is
used. This will allow for further tightening.
Bands/wires should be passed as in Drawings A and B.
Drawing A Drawing B
No. 3 Steel coils recommended securing No. 4 Steel coils recommended

securing
13(49)
Drawing C
(1) The wire is led through the centre of coil "B" from front to rear side.
(2) The end is then passed upwards at the rear side and through the centre of coil "A".
(3) It passes back downwards on the front side through the centre of coil "B".
(4) The wire then passes upwards and diagonally over the top of coil "A" to the front where it is passed
downwards.
(5) It passes through the centre of coil "C".
(6) It then emerges at the rear side. Passing up and through the centre of coil "A";
(7) It continues back down again at the front side through the centre of coil "C".
(8) At the rear side the wire is taken upwards diagonally across the top of coil "A" to be connected to
the opposite end of the wire where it is joined with a span screw.
Drawings:
Courtesy of LLP Limited from the publication Steel - Carriage by Sea - 2nd edition by Arthur Sparks
MNI.
Steel slabs
Mild steel slabs are relatively thin rectangular blocks of steel, weighing up to 20 tons
per piece. A popular size can be 6500mm x 1200mm x 250mm with a specific gravity
of 7.85; such a slab weighs 15.3 tons. Steel slabs are the basic material from which
most steel products are manufactured. Slabs are usually stored in the open -
unusually: for steel products, wetness and rust staining is of no consequence.
The traditional stowage method has been to load slabs with their longitudinal axis
athwartships, right out to the ship's sides over and above the sloping plating of the
hopper tanks. Dunnage was inserted between each tier, to allow re-slinging for
discharge. Building out to the ship's sides produced a staggered stow, more stable
than a uniform pile. With a part load, the best stowage position was thought to be at
either end of the hold, close to the bulkhead.
Such cargoes are now usually carried in bulk carriers, of between 20,000 and 40,000
tons deadweight for full cargoes. In a 30,000 ton ship, the tank tops of the main holds
would be about 16m wide. In such ships, the traditional stowage method would
produce an unacceptable amount of broken stowage, or loss of space, in some
areas.
This can be avoided by combining traditional athwartships stowage with fore and aft
stowage. Complete fore and aft stowage is acceptable in some cases, provided the
stow is built out over the hopper tanks. It is particularly important with steel slabs
always to remember one of the basic principles of good stowage: to interlock the
individual blocks, like building a brick wall. Non-interlocking stacks should be avoided
14(49)
if at all possible. All gaps in the uppermost horizontal tier should be secured with
suitable sized timber.
As stevedores are able to load heavier and heavier weights, methods of stowage
have been devised in which the stevedores simply lower large single loads and stack
them in the hatchway square, leaving large gaps at the sides and sometimes at the
ends of the holds. These methods of stowage are not recommended and should be
avoided for the reasons explained above. It may sometimes be acceptable, but only
in vessels with box-shaped cargo compartments.
The danger of tank top overload should always be borne in mind and avoided by
reference to the permissible tonnage and by use of suitable dunnaging, when
possible
No. 5 Steel slabs awaiting shipment
Hot and cold rolled steel in packages and bundles
Cold rolled steel sheets are wrapped and referred to as packages. Hot rolled steel
sheets are unwrapped, in bundles. Packages usually measure about 1m x 2m x
15cm, weighing about 2,000 kgs. Bundles are of more variable thickness and
therefore variable weight.
These products should be stowed right out to the ship's sides with their longitudinal
axis athwartships. No gaps should be left between the edge of the stow and the
ship's sides/hopper tanks. Packages/bundles usually have bearers, either
longitudinally or transversely. If the bearers are transverse and the units are placed
athwartships, as they should be, two lines of 6"x1" single dunnage boards should be
inserted to tie the stow together and keep it level.
If the tank top is not entirely covered, the "brow of the stow" i.e. the gap between the
end of the stow and the bulkhead(s), or adjacently stowed cargo, must be secured, to
prevent movement in a fore and aft direction. Dunnage can be laid on the tank top as
appropriate.
15(49)
Before commencement of loading, 16mm wire cables should be laid fore and aft,
about 3m apart. When loading is completed, a 6"x1" board lattice fence is fitted to the
face of the stow. The securing wires on the tank top are then brought up over the
stow to be attached with a span screw to the opposite ends, and then tightened.
Gaps between the top layer packages/bundles are secured by wedging and/or
tomming
No. 6 Bundles of hot rolled steel sheeting No. 7 Hot rolled steel in
bundles
No. 8 Cold rolled steel sheeting in packages No. 9 Cold rolled steel sheeting in packages
16(49)
Single plates
Single steel plates are usually quite long and, although heavy, they lack rigidity
because of their length. If they are not handled and stowed carefully, they may
become kinked.
Single plates are ideally stowed in the same way as steel slabs. Suitable lengths of
dunnage should be inserted between each tier of plates or tier of lifts of plates. The
dunnage must be kept in line vertically, close enough together to stop the plates
bending, where there are gaps between dunnage.
Plate-type hooks and clamps are used to secure the wire legs to the plates and are
usually attached to a spreader.
No. 10 Single hot rolled steel plates awaiting shipment
Structural steel
Structural steel products are usually shipped in bulk carriers. Beams and channels
commonly sustain crushing and deformation damage. This can be avoided by placing
the products carefully and correctly, and by proper dunnaging.
Before commencement of loading, 3"x3" dunnage in cross section should be laid in

athwartships lines across the tank top plating. The space between the lines of
dunnage fore and aft, should be about 3 m. This pattern of dunnage should be
separated between every tier, in order to bind the stow together and to allow re-
slinging for discharge. The dunnage should be kept in line vertically. Every effort
should be made to have beams with their webs placed vertically in stow.
These products should ideally be stowed in a fore and aft direction. If they are to be
stowed athwartships, lifts should be placed fore and aft in the wings against the
hopper tanks or ship's sides. The ends of the products should butt up against these
lifts. The ends of athwartships steel must never be allowed to come into direct
contact with the ship's sides.
The stow is secured in the upper tier or tiers. With large beams or channels, wood-
wedges and timber dividers between the gaps is usually adequate. Reinforcing bars
do not normally need to be secured. With bundled goods, some securing may be
17(49)
necessary in the upper tier. Timber or wedges should be driven between the bundles
in the upper tier, particularly with tightly banded, small dimensional angles, etc.
These goods are usually handled by means of chains and wire slings. Care must be
taken not to overload slings. This is especially important when handling beams,
which may become bent or dented at the flanges.
No. 11 Structurals: hot rolled steel beams or joists stored on the open quay
Sheet pilings
Sheet pilings should be stowed in the same way as structural steel, except that they
are stacked on top of each other, to form unsecured bundles. Care should be taken
to ensure that stacks are not excessive, or the top piles may crack.
Special care is needed in slinging. Braided slings are recommended, to avoid

damage to the keying devices on the sides.
Pipes
Small diameter pipes are stowed in the same way as small scantling structural
material. Large single pipes are always stowed fore and aft. Pipes must never be
crossed - each pipe sits in the cantlines of the two pipes underneath. Athwartships
lines of single flat dunnage are first laid upon the tank top and the first tier of pipes is
laid side by side in a fore and aft direction.
If the pipes are not a perfect fit on the tank top or in the lower tiers, wooden stools
should be built in the wings of the areas of the slope of the hopper tank sides.
Some coated pipes require special care in handling. The shipper may provide special
lengths of packing, to stop these pipes chafing against each other. In such cases,
and where there are unusual fabrications and finishes, the shipper should provide
special guidance.
When loading is completed, the top tier of pipes must be secured. With some kinds of
pipes, driving securing timber through gaps and the use of wires may not be
advisable. Side chocking may be required in the area of the wings and the sides of
the stow.
18(49)
The Master should always check stacking limits before the beginning of loading.
Short single pipes may be loaded with wires hooked into the end of the pipes,
attached to a spreader. Bevel ended pipes are loaded by wire slings, but the flat-
plate type hooks on the ends must be copper lined or hard plastic coated. With
special coated pipes, the wire sling may have to be covered in canvas
No. 12 Pipes correctly bundled and strapped
Wire rods
Coils of wire rods usually consist of wire with a diameter of between 5mm and 9mm.
Bundles usually consist of three or four separate coils. Coils may be shipped singly or
in unitised bundles. Units normally weigh about 1.2-1.5mt each. They are secured
with flat metal strapping bands. These should be applied after the bundles have been
compressed. Bundles secured by strapping bands are very rigid - in this state they
are in the best condition for stowage in a ship's hold. Slack bundles which are not
tightly pressed and secured in this way can suffer during handling, securing bands
can converge and through pressure in the stow, wires can splay out and become
damaged. In addition, serious tangling of windings can result.
Two lines of single flat dunnage should be laid on the tank top athwartships under
each line of coils. Wire rods are not a high density cargo. Unlike most steel cargoes,
they take up a lot of hold space. Coils or bundles are stowed on the tank top in lines
across the hold, with the centre core pointing fore and aft. These products are stowed
in the same way as hot/cold rolled steel, but with rods it is not necessary to arrange
locking coils. Sometimes these cargoes are simply dumped in the hold. This should
not be allowed. These products need to be stowed carefully and properly, like any
other. The wire should not be allowed to rest against the ship's structure, or chafing
damage can occur.
19(49)
If it is intended to load a different, low density cargo on top of wire rods, remember
that wire rods settle and sink considerably after loading. Stowage and lashing of
other cargo on top should be planned with this fact in mind.
Soft copper wire rod is shipped in an unpacked condition and if great care is not
taken, it may become chafed, kinked or scored, causing substantial cargo claims.
Wrapped Unwrapped
No. 13 High tensile wire rods No. 14 Hot rolled wire rods: no wrappers
fully wrapped (unprotected) stored in the open air
Stowage certificates
If a Surveyor has been appointed to follow the loading operations, he should produce
a stowage certificate showing:
- Stowage per cargo hold.
- Dunnaging of cargo.
- Measures taken to secure the cargo.
- Any interventions by the Surveyor which have led to changes in the stowage/lashing
arrangements.
- Details of any differences of opinion, with whom, on what subject, with what result.
Before departure, the Master should be provided with copies of a stowage plan,
hatch lists, etc. He may be asked to sign a document confirming that stowage and
securing has been carried out to his satisfaction. The Master should obviously not
sign this document if he disagrees with it or has any doubts.
20(49)
The golden rules of stowage

Proper and efficient stowage is essential to avoid shifting, chafing and crushing
damage. The guidelines for particular cargoes, as set out above, should be followed,
and the following five Golden Rules should always be observed.
Golden Rule 1:
Before loading begins, check that there is adequate suction on all bilge lines. The
date of the test and results should be appropriately entered in the deck log book.
Golden Rule 2:
A reasonable inspection of the cargo holds must be carried out before loading
commences. The date and name of the vessel's officer who inspected the holds must
be entered in the deck log book.
Golden Rule 3:
Never go to sea with the top horizontal tier of a steel cargo not fully completed. If the
tier cannot be completed it should not be loaded, as securing with wires to the ship's
sides and tomming with timber cannot be considered as proper precautions against
shifting with this type of cargo and in this particular situation. In certain circumstances
this rule may not apply to steel coil cargoes.
Golden Rule 4:
Steel products should never be permitted to rest against the ship's structure in stow:
dunnage should always be used to prevent this occurring.
Golden Rule 5:
Underdeck steel cargoes should not be secured to component parts of the vessel's
structure, with the exception of wire rod cargoes in certain circumstances (for
example, half hatch stowage).
21(49)
PART 2 CARGO CARE
SECTION 2 - ON THE VOYAGE
Supervision of loading, stowage and discharging

Surveyors may be available to help and advise the Master but it is the Master's
responsibility properly and carefully to load, stow, carry, care for and discharge the
cargo. He may at some stage be obliged to prove that he fulfilled this responsibility
and in doing so took all measures humanly possible to protect the cargo while it was
in his custody.
The maintenance of the vessel

In negotiating cargo claims, damage caused by lack of maintenance of the vessel
often leaves the carrier with no defence. As a result of this he may have to pay the
claim in full or otherwise settle on very poor terms even when other factors have
played an important part in causing the damage. Proper maintenance is, of course,
essential.
Watertightness
Steel cargoes are almost always high density deadweight cargoes. Vessels carrying
these cargoes have a high range of stability and work heavily in a seaway, imposing
concentrated stresses in various areas of the hull structure; especially in the area of
the hatchways. If the hatches are to remain watertight it is essential that all
component parts of the steel hatch closing appliances are maintained to a high
standard. This also applies to all other main deck openings.
Ventilation
Most moisture damage and subsequent rust damage to steel cargoes is caused by
cargo sweat and/or ship sweat. Steel loaded in a cooler climate going to or through a
relatively warmer climate will, if ventilated, probably suffer from cargo sweat (that is,
condensation of moisture directly onto the actual cargo). On the other hand, when a
ship travels from a warm area to a relatively cooler area, the steel cargo is vulnerable
to being affected by ship sweat (that is, condensation forming on the component
parts of the ship's structure within the cargo holds dropping back onto the cargo) if
proper ventilation does not take place.
Steel cargoes should therefore not be ventilated when passing from a cool climate to
a relatively warm climate. Cargo should be given full ventilation when temperatures
are falling. It will therefore be necessary to maintain temperature records from the
commencement of loading up to completion of discharge. These records will enable
the carrier to prove that all necessary measures were taken to care for the cargo
during the course of the voyage. In the negotiation of cargo claims it is of great
importance that correctly kept records are available which will accurately and
acceptably correspond with the manner in which the ventilation was used.
When it is decided that the cargo should not be ventilated every effort must be made
to seal off the cargo hold from the outside atmosphere. The aim should be to make
the cargo hold as air-tight as possible. If cargo hold dew point temperatures are
closely following outside atmospheric dew point temperatures, then the exercise is
not working: hold sealing arrangements should be re-checked.
22(49)
If there is any leakage of hatches, however slight, or the ingress or presence of free
moisture in the cargo hold (for example, due to a flood back along bilge lines, the
ingress of rain during loading, the presence of other cargo loaded in a wet condition,
or the cargo holds not being dry when loading commences), there will be an
appreciable increase in the relative humidity of the ambient air surrounding the cargo,
resulting in copious cargo sweat and ship sweat, possibly accompanied by serious
cargo damage.
Some Owners/operators equip their ships with either permanent or portable cargo
hold dehumidification units which have proved to give satisfactory results.
23(49)
Carriage of steel cargoes - Part 3 Surveys

SECTION 1 - PRE-SHIPMENT SURVEY - CARGO
Information for the Surveyor

If a pre-shipment survey of cargo is planned, the Surveyor should be provided with
the following information:
- Name of ship.
- Expected time of arrival.
- Loading terminal.
- Identity of applicant for survey.
- Name and full contact details of Agents.
- Instructions (for example, to survey all cargo or only particular parcels, or to survey
cargo only or both the cargo and ship).
When to instruct a Surveyor

The Surveyor needs enough time to survey the cargo before commencement of
loading. The length of time needed depends on the quantity of cargo and the number
of parcels. As a rough guide, the Surveyor needs one clear day per 15,000mt of
cargo. Fewer parcels mean fewer documents and less time is needed.
The Surveyor's duties

The Surveyor carrying out a pre-shipment cargo survey has a number of tasks:
(1) To survey the parcels of cargo for: - rust condition - mechanical/handling damage.
The Surveyor should take any necessary photographs, preferably using a date
insertion camera, and make a full note of the photographs he takes.
(2) To prepare descriptive clauses of any damage, to be inserted on Mate's Receipts
and Bills of Lading. Cargo affected by rust or mechanical damage is not in apparent
good order and condition and should not be so described. The Mate's Receipts and
Bills of Lading should be appropriately claused to reflect the true condition of cargo.
(3) To ensure that the person in touch with the Shipper (for example, the chief tally
clerk, or the Agent) obtains a copy of any descriptive clauses and passes them on to
the shipper before the affected cargo is loaded.
(4) To assist the Master. If appropriate, the Surveyor should:-
- warn and advise the Master not to sign Mate's Receipts or Bills of Lading as
presented except in the surveyor's presence;
- check that the descriptive clauses he has prepared are fully inserted on Mate's
Receipts and Bills of Lading before they are signed;
- support the Master, if appropriate, in insisting that the Mate's Receipts and Bills of
Lading are claused as necessary;
- help and advise the Master if it rains during loading.
N.B. It may be inappropriate for the surveyor to assist the Master if the Surveyor is
appointed on behalf of a Charterer Member (rather than an Owner Member).
24(49)
Preliminary report
As soon as the vessel has sailed (but in any event within 24 hours) the surveyor
should send, by fax, a preliminary written report covering:
- Date and time of sailing.
- Port(s) of discharge, quantity of cargo per port, total tonnage loaded.
- ETA port(s) of discharge.
- General observations on the condition of the cargo.
Final report
After the vessel has sailed (but in any event within 5 working days) the Surveyor
should send, by courier, a full written report containing the following information:
- Name of the applicant.
- Name of the vessel including relevant voyage number.
- Name of the Master.
- Name of the Chief Officer.
- Gross tonnage.
- Port of Registry.
- When and where built.
- Details of safety construction certificate.
- Details of last load line survey.
- Details of classification certificates and conditions of class (if any).
- Details of last special survey.
- Name of Owners and Operators.
- Name of Charterers' Agent.
- Name of Owners' Agent (protecting agent or not).
- Purpose of the survey.
- Date of arrival of the ship.
- Date when survey of steel commenced.
- Date and time when the Surveyor first boarded the vessel.
- Place where the vessel was berthed.
- Details of any discussions with the Master.
- Details of the cargo including:
(a) Number of Mate's Receipts and relevant Bills of Lading;
(b) Details of the parcel involved (for example, the number of pieces, packages or
bundles, type of goods);
(c) Condition of each parcel of cargo clauses if any, entered in the Mate's Receipts
and Bills of Lading;
(d) Details of the pre-shipment storage (for example, covered or uncovered on open
quay, covered or uncovered rail wagons, open barge or coaster).
(e) Cargo hold stowage per Mate's Receipts or Bill of Lading.
- Details of tonnages loaded for each discharge port and where stowed in the vessel.
- Details of any stevedore damage (with copies of any letters of reserve/protest to
accompany the report).
- Details of any stoppages for rain including details of whether the hatches were
closed and, if so, whether closed in sufficient time to prevent cargo from becoming
wet. It should be noted whether cargo brought forward for loading had been
protected from contact with rain during any stoppages.
- Condition of the cargo holds prior to commencement of loading in relation to
cleanliness and suitability to receive the intended cargo.
- Results of silver nitrate test on tank tops and ship's sides.
25(49)
- Atmospheric temperatures prevailing during loading.

- Every effort should be made to obtain a copy of the cargo plan and a copy of the
statement of facts to accompany the report.
- Photographs of the cargo should accompany the report, preferably with dated
exposures.
26(49)
PART 3 SURVEYS
SECTION 2 - PRE-SHIPMENT SURVEY - THE VESSEL
If such a survey is to be carried out, it should be done as soon as possible after the
vessel's arrival at the load port. The surveyor should invite the Master or Chief Officer
to attend. The following guidelines should be observed.
Cargo holds
The surveyor should check the condition of the cargo holds before the
commencement of loading. If the hold is not in a suitable condition, the surveyor
should report immediately, before any cargo is loaded.
If cargo compartments are washed with salt water in preparation for loading they
must be given a final fresh water wash to remove any salt crystals. The surveyor
should make spot checks with silver nitrate on the sides of the holds and on the tank
top plating. This is particularly important when the discharge port is in the United
States, where such tests are commonly carried out on discharge.
Steel hatch covers and other deck openings

Most bulk carriers employed in steel trades are fitted with MacGregor type wire-
operated hatch panels. Alternatively, the panels may be operated by chains or by
hydraulics. In most cases, the following checklist, with any necessary modifications,
is recommended.
Check list
General
(1) Favourable comments.
(2) Adverse comments.
(3) Types of hatchcovers involved.
Panels
(1) Well painted up, free from rust, rust scale or indentations, affected by rusty
patches and scattered dents but general condition not considered to affect the
strength of the appliances
OR
(2) Rusty, partly rusty, in appearance. Affected by rust scaling. Corrosion
(light/heavy). Affected by scattered dents. General condition poor and considered to
affect the strength of the appliances.
Rubber packing (gaskets)

(1) Rubber jointing pliable, not unduly compressed. Not torn, chafed or defective in
any respect
OR
(2) Locally chafed, torn and/or distorted (squeezed or pinched in the retaining
channels). Not firmly affixed in the retaining channels. Rubber jointing hanging out of
retaining channels in places. Rubbers perished, hardened and lacking necessary
pliability. Rubbers affected by heavy and unusual compression marks.
27(49)
Retaining channels
(1) Free of rust scale or any deformation
OR
(2) Rusty, corroded, locally distorted, bent and/or torn.
Compression bars
(1) Free of rust scale or any deformation
OR
(2) Locally bent and/or torn in places. Waved along length. Locally waved in places.
Affected by heavy (light) corrosion (points of corrosion). Distorted (locally) or (along
length). Affected by heavy (light) corrosion. Metal parts seriously wasting away
through corrosion.
(a) Transverse guttering and (b) Hatch rims

(a) (1) Free of rust scale, serious corrosion or any deformation
OR
(2) Channel bars locally bent and/or waved. Metal work generally corroded. Locally
wasted away through corrosion.
(b) (1) Free of corrosion or any physical damages

OR
(2) Hatch rims locally wasted and reduced in height through corrosion. Deeply
scored.
Steel to steel contact points

(1) No distortion, bending or excessive grooving
OR
(2) Sections bent. Heavily grooved, distorted and/or partly broken off.
Snugs
(1) Free of rust scales or any defects
OR
(2) Corroded - diminished in size. Holding properties diminished.
Crutches
(1) Free of rust scale or corrosion
OR
(2) Heavily rusted or corroded. Partly crushed. Completely crushed. Distorted.
Quick-acting cleats, rods, nuts and washers/ other cleating arrangement

(1) Free of rust scale or any defects. Rubber washers pliable. Corroded but corrosion
not serious - general condition acceptable
OR
(2) (Number) corroded - cross sections area of rod diminished. Strength of rod
impaired. Rod bent. Washers hardened and perished. Washer crushed. Tightening
nut rusted and inoperable.
28(49)
Cross wedges (cross joint cleats)

(1) None missing - all in place when surveyed. Wedges not bent, side springs
complete and in good working order
OR
(2) (Number) cross wedges bent. (Number) cross wedges with inoperable springs.
(Number) cross wedges with side springs missing. All cross wedges not in place at
time of survey. Wedges tightened over welded pads on adjacent panel edges.
Inboard drainage system

(1) Coaming drain channels and all guttering free of loose scale, foreign matters
and/or obstructions. Drain holes unobstructed, in good order and condtion also in
good working order. Non-return drain valves free and working correctly
OR
(2) Coaming drain channels partly (completely) obstructed with residues of previous
cargo. Coaming drain channels corroded (lightly) (heavily). Drain holes blocked with
residues of previous cargo (with rust scales). Non-return drain valves jammed and
not in good working order. Drain holes not fitted with valves and drain pipes open.
Wheel tracks (guide rails)

(1) Free of loose scale clean and unobstructed
OR
(2) Worn, grooved, uneven, waved. Corroded (heavily or lightly) and weakened.
Wheels
(1) Well greased and free running
OR
(2) Seized up. Spindle bent, wheel not working.
(a) Panel side chains (b) Hinges (c) Hydraulics

(a) (1) Free of scale and correctly adjusted
OR
(2) Affected by rust scale and requiring adjustment.
(b) (1) Hinges in apparent good order and condition. Panels not misaligned
OR
(2) Hinges rusty and adjacent areas rust streaked. Wear down of hinge spindles
apparent with resulting misalignment of panels.
(c) (1) Hydraulic system functioning correctly. No leaking of oil from joint connections
or hoses
OR
(2) Hydraulic system malfunctioning. Oil leaking from hydraulic system.
Access hatches
(1) Cleat bolts and wing nuts working freely: wing nut thread well greased up. All
cleats in place and complete with wing nuts. Packing pliable, complete and
undamaged
OR
(2) Cleat bolt section seized up on operating spindle (all or give number). (Number) of
cleats wing nuts missing. (Number) of wing nuts seized up. All (or give number)
29(49)
cleats rusty, corroded and completely inoperable. (Number) cleats bent and
inoperable. Packing torn, hardened, perished, sections missing. Packing retaining
channels locally bent, rusty and corroded.
Access doors
(1) All securing lugs complete working freely and fully operable. Sealing rubbers
(door edge packing) pliable and in good condition
OR
(2) Out of (give number) lugs, all (or give number) seized up and completely
inoperable. Out of (give number) lugs (give number) missing. Sealing rubbers (door
edge packing) hardened, perished, partly missing.
Bilge sounding caps

(1) Operating correctly and capable of being fully screwed down
OR
(2) Thread of cap damaged, cannot be properly screwed down in place. No proper
cap fitted. Cap missing. Pipe opening closed with a wooden plug.
Sealing tape
The use of sealing tape on hatch covers is not recommended. Hatches are designed
to be weather-tight; that is, they must be watertight in normal weather conditions. If
they are in good order and well-maintained they will be.
In bad weather, experience shows that sealing tape is either ineffective or is simply
washed away.
As well as being ineffective, the very use of sealing tape can be harmful to the
carrier's interests - it can be regarded as an admission of lack of confidence in the
watertightness of the hatch covers.
In short, sealing tape is not an effective way of creating a watertight seal and its use
in any case a bad sign - it will not help to protect either the cargo or the carrier, and
may even be harmful to the latter.
Testing for watertightness

In addition to a visual inspection of cargo holds and hatch covers, the surveyor
should, if instructed, test the hatch cover panels for watertightness. Any defects
should be noted by the surveyor, reported to the responsible deck officer and
competently repaired, before the start of the voyage.
Three methods of testing are available: ultrasonic; hose; chalk.
Ultrasonic test
This can be the most reliable method. It is the preferred method of testing, but only if
the surveyor is certified to carry out ultrasonic testing and is using properly certified
and calibrated equipment approved by Skuld. It has a number of advantages:
- It can be used on loaded or partly loaded vessels without damage to cargo.
- It can be done by one person.
- It is less time-consuming than other methods.
- It reveals the exact location of any defects.
30(49)
- Equipment is easy to use.

- It can be used at below zero temperatures.
The Master is to be informed of the scope of work and intended procedure. Personal
safety measures are to be agreed.
The Club's requirement is that only competent and qualified operators, with properly
certified, calibrated and approved equipment, should be allowed to use the ultrasonic
equipment for testing hatches for watertight integrity. Therefore, ultrasonic testing
should only be carried out if the Association has expressly authorised the surveyor to
do so.
Hose test
If the Association has not authorised an ultrasonic test, hose tests should be carried
out.
IACS (The International Association of Classification Societies Ltd.) International

Guidelines 1985 dictate how the test should be carried out. They specify that the
nozzle diameter must be a minimum of 12mm, that the end of the nozzle of the hose
delivering the stream of water should be held at a maximum of 1.5 metres from the
joint being tested, that the pressure to be used should be sufficient for a free height
of water with stream directed upwards of at least 10 metres.
The actual joint to be tested is situated some distance below the surface of the hatch
panels, which meet to form a very narrow gap. Therefore, the water from the hose,
when testing, cannot be directed onto the actual joint forming the watertight seal. In
fact the force of the water directed towards the joint is dissipated against the surface
of the hatch panels. Hose testing has for many years been the principal method of
testing, because there was no other known method available, other than the less
satisfactory chalk test. However, hose testing is still an acceptable method of testing
for watertight integrity. It is usually necessary to use two surveyors and in order to
increase the efficiency of the test it is advisable to plug the drain holes on either side
of the transverse joint so that the guttering can be filled with water.
Chalk test
This test method should be the last resort. If other methods are not possible, this test
is achieved by applying ordinary chalk to all compression bars, closing the hatches
and then re-opening them to see if imprints of the chalk on the sealing rubbers can
be observed. The benefit of this test is that it can be performed with or without cargo
in the ship. On the other hand, application of the chalk to the compression bar is
time- consuming. Heavy and light imprints on the rubber gaskets can give rise to
indecision as to how effective the test really is. Naturally, areas where there is no
imprint must mean absence of contact between the compression bar and the rubber
seal; these are obviously areas of potential leakage. This test is more often used, and
is useful, when rubber gaskets have been renewed.
31(49)
The survey report

Preliminary
If any significant defects are found, the Surveyor should report, by phone or fax, to
the Club immediately. He should also report to the Master if appropriate.
Upon completion of the survey and in good time before the vessel sails from the port,
the Surveyor should report by fax to the Club setting out details of any defects found
during the survey. If appropriate, he should provide the Master with a copy.
Final report
The Surveyor should without undue delay (but in any event within 5 working days),
send a full written report, by courier, containing the following information:
- Name of Surveyor.
- Date of report.
- Name of applicant for survey.
- Summary of Surveyor's terms of reference.
- Name of the vessel.
- Type.
- Gross tons register.
- Port of registry.
- Classification Society.
- Date built.
- Place built.
- Details of safety construction certificate.
- Details of classification certificates and conditions of class.
- Details of last special survey.
- Details of last load line survey.
- Number of cargo holds.
- Number of deck hatches per hold.
- Hatch closing system.
- Number of deck ventilators per hold.
- Ventilation system.
- Number of sounding pipes per hold.
- Number of access openings per hold.
- Number and type of other weather deck openings.
- Name and city of Owner.
- Name and city of Manager/Operator.
- Name and city of Charterer.
- Name of Charterers' Agent at port of loading.
- Name of Owners' Agents/P&I Correspondent at port of loading.
- Names and business of others in attendance.
- Location of the loading berth.
- Time and date the vessel arrived.
- Time and date Surveyor proceeded on board.
- Time and date copy of preliminary report handed to the Master.
- Time and date loading commenced.
- Time and date vessel sailed.
- Full details of test for watertight integrity.
32(49)
- Full details of repairs and adjustments after preliminary report to the Master.
- Photographs of damages, defects and repairs as found necessary (with the
photographs showing exposure dates).
- Report on condition of hatches.
33(49)
SECTION 3 - DISCHARGE SURVEYS
Instructions to Surveyor
When a Surveyor is instructed to attend the discharge of the cargo, the hatches
should, if possible, remain as they were at sea (that is, unopened and all securing in
place) until the Surveyor has the opportunity to survey the hatches. He should be
able to report that, upon boarding the vessel he ascertained that the hatches were
still in their undisturbed sea-going condition with all securing wedges and quick-
acting cleats fully and firmly in place. The Surveyor should witness opening of
hatches and either report that all cargo in sight was dry and in apparent good order
and condition or give a full description of what he observes when the hatches are
open. If leaking hatches are involved the Surveyor should conduct a full hatch survey
similar to that which he would carry out when performing a pre-shipment survey. He
should follow the discharge of the cargo, consider and study the cause of any
damages found in stow with a view to reporting on them. Surveyors should
particularly bear in mind that it is advisable for them to attend towards the completion
of discharge, as it is in the bottom of the cargo holds where damages from
overstowing pressure and unexpected moisture damages can show up.
In any event, where damage has occurred and is evident, the Surveyor should take
an active and prominent interest in ensuring that, in discharging, sorting and storing
damaged cargo after discharge, everyone involved acts fully in the interests of
mitigating the loss. For example, even where wrapped cargo has sustained heavy
mechanical damage, it should not be left on the open quayside exposed to the
elements. In addition, he should try to ensure that no steps are taken which prejudice
the member's interests; for example, cargo which has been partly in contact with
sea/salt water should never be washed down with fresh water from the city mains:
city mains water is invariably contaminated with chlorides. There are many other
factors, too numerous to mention, of which the competent Surveyor should be aware.
The survey
Any damaged cargo discharged from the ship should be the subject of a statement
from the Master. Depending upon what the damage actually is, and how it was
caused, the following is a check list of matters which the Surveyor should refer to in
his report. In collecting information, it must be left to the Surveyor's discretion as to
what is relevant to the actual cause and circumstances of the damage.
- Name of applicant and the party whom he represents.
- Name of the ship and number of the relevant voyage.
- Gross tonnage and port of registry.
- Purpose of the appointment.
- Date when the surveyor went on board the vessel.
- Place where the vessel was berthed.
- Name of the Owners.
- Name of Operators.
- Name of Charterers and/or their Agents.
- Name of Owners' Agents (whether shared with Charterers or acting as protecting
Agents).
- Name of Classification Society.
34(49)
- Details of safety construction certificate: -

-- classification certificate;
-- last load line survey;
-- last special survey;
-- any conditions of class.
Copy documents which should be obtained

- Copies of the relevant log book pages.
- Copies of relevant Mate's Receipts and Bills of Lading.
- Copies of voyage ventilation records.
- Copies of bilge sounding records.
- Copies of any correspondence between the stevedores and/or the Charterers at the
port of loading and the port of discharge relevant to any current voyage cargo
damage.
- Copy of the cargo plan.
- Copy of any documentation received from Charterers, shippers or stevedores
relating to any current voyage cargo damage.
- Copies of ship's plans as found relevant/necessary (for example, ventilation plan,
piping plan, general arrangement plan and capacity plan).
- Statement of Facts covering discharge of the ship, to be checked against deck log
book times for the same periods.
Contents of the Surveyor's report relative to the cause of any damage

Non-return valves on bilge lines
Check that they are working properly. Valve chest on the engine room side of the aft
bulkhead should be opened and the seating of the valves examined and/or any other
relevant parts of the bilge pumping system.
Tank tops
- Details of pressure testing.
- If damage is associated with a crack in the tank top, give details of the exact
position of the crack, whether the crack has come into existence through damage to
the tank top, the general physical condition of the tank top or weakness in the
welding.
- If damage is associated with leaking tank-top manhole lids, give details regarding
the state of the packing - type of packing - also the studs and securing nuts.
- Are the manholes recessed and/or fitted with protection covers?
- Holes in pipes.
- The apparent condition of the pipe in general should be reported.
- The exact position of the hole, or holes, should be recorded and it should be
clarified whether the hole/holes has come into existence through the effects of
corrosion resulting from lack of maintenance, or through the effects of erosion from
within the pipe (that is, from an inside or outwards direction).
- Is the hole or defect in an accessible position? Would the defect have been visible
from a reasonable inspection of the cargo hold prior to loading cargo?
- With leaking pipe flanges it is necessary to state whether or not the flanges were
completely parallel; mention the type of packing used also its condition,
measurements of the flange sizes of the holding bolts and general condition.
- Where substantial condensation damage is concerned the surveyor should carry
out a full ventilation survey as referred to earlier.
35(49)
The survey report

Preliminary
Upon completion of the survey it will be necessary for the surveyor to produce a
preliminary report, briefly referring to identification details of the incident, the nature of
the damage, and the cause and circumstances of the damage sustained by the
cargo.
Final
The final survey report will contain full facts relating to the survey and be completed
by the surveyor giving his considered opinion as to the cause of the damage.
However, it is emphasised that surveyors should on no account include in their
reports any opinions as to liability.
Stevedores' outturn report

Upon completion of discharge it is customary in many ports for the stevedores to
present the Master with a stevedores' outturn report for his signature. This document
usually gives a general description of items of cargo which, according to the
stevedores, were allegedly found damaged prior to discharge, before the goods were
handled by the stevedores. If these damages were not brought to the attention of the
Master before being handled by the stevedores, he should refuse to sign the report. If
the damages were brought to the attention of the Master, at the correct moment, then
he may sign the report "for acknowledgement of receipt only." The descriptions and
quantities referred to in these reports are often inaccurate.
Who should be authorised to board the vessel and examine the cargo?
In many ports when a vessel arrives with a cargo of steel on board, it is not unusual
for cargo interests' surveyors to board the ship, proceed into the cargo holds, take
photographs and test surfaces of the cargo and the ship's structure with silver nitrate,
without letting anyone know who they are, or what their business is on board the
ship. Such people ignore the fact that a ship is private property: they should present
themselves to the Master, explain why they are on board and obtain the Master's
authorisation to remain on board.
Surveyors representing cargo interests can survey the cargo after it is landed ashore
from the ship but should not be allowed to do anything on board without the Master's
permission. The Master should refer such Surveyors to his Agent or the Club's
Correspondents who would then advise the Master as to whether he, the Master, is
under any obligation to permit the Surveyors on board. If eventually the cargo
interests' Surveyor is allowed on board the vessel, he must be accompanied by the
carriers' Surveyor and also by a member of the vessel's staff. It should be
remembered that voyage records kept by the ship are private documents so that
caution must be exercised as to who is permitted to examine them.
If a claim or arrest is made on the vessel, the Master should notify the Club's
Correspondents who will immediately inform the Club so that appropriate action can
be taken.
36(49)
SECTION 4 - CARGO/COMMODITY SURVEY
The survey
If it is alleged that cargo has been damaged, a Surveyor may be instructed to inspect
the cargo after discharge. The Association might agree to a joint survey with the
cargo interests to see if all interested parties can reach joint agreement as to the
extent of the damage. At such surveys, Surveyors should keep in mind that it is
incumbent upon the receiver to show the damage and prove any loss which he will
be claiming. It should also be borne in mind that the receiver cannot claim any loss
which could have been avoided had he taken reasonable steps to mitigate his
damages.
The survey report

Preliminary
This should be a short report identifying the case in question and briefly explaining
the aspect, nature and extent of the damage.
Final
The final report should include details of the following:
- Name of the applicant and whom he represents.
- Date and place where the survey was held.
- Purpose of attending the survey.
- Name of the vessel, date of arrival and date of discharge of the cargo.
- Bill of Lading details concerning the goods to be surveyed.
- Names of all present at the survey, who they represent and in what capacity.
- The name of the receiver.
- Details of the holds from which the cargo was discharged.
- Confirmation that the goods were properly identified as being the actual goods to be
surveyed. There are instances where Surveyors have been too casual in their
approach to the survey and have either surveyed the wrong goods or have surveyed
goods as presented which could not be identified with the shipment in question.
- Description of the goods (for example, packing, securing, weight per unit).
- A complete descriptive report of the damage before and after the packing is
removed.
- The nature of the damage; for example, contact with fresh water, chlorides, liquids,
powders, grease, oils. Joint samples should be taken and retained for future
reference. Analysis of samples, if found necessary, is in most instances for the
account of cargo interests as part of their obligation to determine the nature of the
damage.
- Comments on the damage must include a full and complete explanation as to how
the receiver justified the allowance he obtained from the Surveyors and on what
basis the Surveyors were prepared to agree and accept the allowance as being fair
and reasonable.
- If agreement as to the extent of damage cannot be reached, details and evidence
should be provided as to why the cargo interests' Surveyors' figures were
unreasonable.
- When a receiver attempts to reject his cargo and insists that he be allowed to
abandon the goods (in which case the goods would in all probability have to be
disposed of by sale) such action should not be approved by the Surveyor, unless it
can be proved by the receiver that he is unable to use the goods on account of the
37(49)
damaged condition which initially gave rise to the claim. All events and discussions of
importance leading up to the acceptance, or non-acceptance, of the cargo are to be
reported.
- Any information or evidence which might be useful in defending the claim.
Silver nitrate testing and sampling

Silver nitrate solutions for testing for chlorides are not reliable unless they contain an
amount of chlorine-free nitric acid: without the presence of this constituent in the
solution it will react to alkalis. For this reason surveyors should use their own solution
to check when complaints are made by cargo interests' Surveyors that goods are
contaminated by chlorides. As silver nitrate solutions deteriorate with time, Surveyors
should test their own solutions. The mains tap water usually gives a brackish reaction
and this can therefore generally be used.
Official rust samples or samples of the material should be selected jointly and sealed.
Samples of the actual material must be selected with care. Instances will arise where
the samples have to be properly wrapped and protected without being touched by
human hands. Sodium chloride (NaCl) is exuded through the pores of the human skin
and can contaminate samples, this being of importance where traces of NaCl might
enter into future arguments concerning the nature of the damage.
A silver nitrate test with positive results is not conclusive evidence of contact with sea
water; it is only an indication that sea water might be involved. If cargo interests
maintain that there has been salt water contamination then the carrier's Surveyor
must ensure that there is a quantitative analysis by a reputable laboratory, where all
the solids found in sea water are identified as being present and in the correct
proportions
38(49)
Carriage of steel cargoes - Part 4 The Bill of

Lading
SECTION 1 - THE LEGAL POSITION
A "clean" Bill of Lading.

As a general rule, the carrier must, on demand of the shipper, issue a Bill of Lading
showing "the apparent order and condition" of the cargo at the time of loading.
A "clean" Bill of Lading is one which describes the cargo as being in "apparent good
order and condition", without containing adverse remarks. A clean Bill of Lading is
effectively a representation that, at the time of shipment, the cargo was in good order
and condition as far as would be apparent from the type of inspection which a
reasonable carrier could be expected to make. This representation will usually
prevent the carrier from arguing that any damage to the cargo occurred before the
cargo was received into his custody.
For example, if a carrier issues a clean Bill of Lading for steel coils which were rust
stained before shipment, the carrier can usually be held liable to the receiver for that
rust staining. The carrier cannot argue that the coils were already rust stained when
loaded onto his vessel, because he is bound by the clean Bill of Lading he issued.
The statements in the Bill of Lading as to the apparent order and condition must be
accurate: the carrier is not protected if he or the Master use reasonable care but still
issue an inaccurate Bill. Consequently, if in doubt the Master should seek guidance
from the Club Correspondent or a Surveyor appointed to assist. Any remarks on the
Bill of Lading usually reflect remarks in the Mate s Receipts, so the remarks in the
Mate s Receipts must also be accurate.
Letters of Indemnity
In the "real world", the shippers often need a clean Bill of Lading for their sales
contracts or letters of credit and they may attempt to persuade the vessel's
Charterers or Owners to issue a clean Bill, even though the cargo is obviously not in
apparent good order and condition. In return for a clean Bill of Lading, the shipper will
often offer a Letter of Indemnity which, on its face, appears to indemnify the owner or
charterer against all possible consequences of issuing a clean Bill of Lading.
It is, however, extremely dangerous to issue a clean Bill of Lading in these

circumstances. Firstly, the issue of a Bill of Lading containing a false statment is a
crime in many countries, as it is, in essence, a conspiracy by the shipper and the
carrier to defraud the receiver. Secondly, any Letter of Indemnity would almost
certainly be legally unenforceable. Even where shippers have honoured such Letters
of Indemnity in past cases (for commercial reasons) they may not do so in future
cases, where the sum involved is more substantial and where there is a dispute as to
the extent to which damage has a pre-shipment origin. Thirdly, the Member will lose
his P&I cover if he issues, or authorises the issue of, a clean Bill of Lading for cargo
39(49)
which he knows is damaged. The only circumstances where a Letter of Indemnity

may be acceptable is where there is a genuine dispute as to whether a clean Bill of
Lading should be issued.
Claused Bills of Lading

Where the cargo is not in apparent good order and condition, the carrier is entitled to
insist on the Bill of Lading being claused.
If there is no Charterparty applicable, the carrier can probably decide on his own
wording for the clausing, provided that the wording is neither inaccurate nor
misleading. However, if the carrier exaggerates the severity of any damage or
defects, he may be liable to the shippers.
If there is a Charterparty, the carrier may be under an obligation to issue Bills of

Lading "as presented". In those circumstances, the shippers are probably entitled to
decide on their own wording for the clausing but the carrier is still not obliged to
accept that clausing if it is inaccurate or misleading.
As a general rule, a carrier should attempt to agree the wording of clausing with the
shippers: in practice, the pre-shipment Surveyor will, at many ports, negotiate routine
clausing with the shippers on behalf of the carrier. If, however, an agreement cannot
be reached, in cases where the dispute may be significant, the Club should be
notified (either directly or through its Correspondents) since there may not only be a
factual or expert dispute (as to the extent to which the cargo is not in apparent good
order and condition) but a legal dispute as to the identity of the party entitled to
decide on the precise wording of any clausing.
40(49)
SECTION 2 - CARGO CONDITION CLAUSES
There is no single standard wording for clausing Bills of Lading in the steel trade but
the following descriptive clauses are recommended by Skuld in appropriate cases:
"Rust stained"
When 75% or more of the surface area of the item of cargo/cargo is covered
with a fine, light coloured film of rust which when removed by wire brushing,
scraping or wiping reveals a smooth, bright metallic surface
No. 15 Rust stained
"Partly rust stained"

When under 75% of the surface of the item of cargo/ cargo is covered with a
fine light coloured film of rust as described for "Rust Stained" above
No. 16 Partly rust stained
"Rusty"
When 75% or more of the surface area of the item of cargo/cargo is covered
with a dark brown coloured rust formation, which when removed by scraping or
wire brushing reveals an uneven, dull surface still rusty in appearance to some
degree.
41(49)
No. 17 Rusty
"Partly rusty"
When less than 75% of the surface of the item of cargo/cargo is covered with a
dark brown coloured rust formation as described for "Rusty" above
"Rust Spots Apparent"

Localised very slight penetration of rust in the form of rusty spots and especially in
areas where the mill scale coverage is broken or fragmented. The spots are not
prominently bulbous in appearance and, when cleaned away, leave a smooth steel
surface.
No. 18 Rust Spots Apparent

42(49)
"Rust spotted"
Localised penetration of rust through the mill scale. Bulbous, revealing an uneven
surface when removed by wire brushing. Parts of the surface without mill scale may
be rust stained with rust spotting.
"Wet before shipment"

Partly or totally wet surfaces apparent before shipment but may only become
apparent when moved for shipment (for example, water can run out of the inside of
structural steel, when lifted). When lifting hot rolled coils, flexing of the windings often
squeezes out water from between the turns of plating; in which case, although initially
apparently dry, the goods are wet before shipment.
No. 19 Rust spotted
"Rust with pitting"

Deep brown coloured rust which, often with rust scale formation, when removed by
wire brushing or scraping reveals pitting of the surface of the steel.
No. 20 Rust with pitting
"Covered with snow"

Visible surfaces partly or totally covered with snow and/or ice.
43(49)
"Areas of steel surfaces reacting to silver nitrate solution tests"

Suspect areas should be tested. If they react, the test is proof that chlorides are
involved: see the comments above on silver nitrate testing and sampling.
No. 21 Silver nitrate. Note milky white area: positive reaction
"Stained by an unidentifiable powder"

These powders are often hygroscopic and contain chemicals which can be
aggressive to steel surfaces. The colour of the powder may be mentioned. Surveyors
should endeavour to take and retain samples of the powder.
"Rust streaked"; "evidence of contact with free moisture - drip down rust
streaks"
These clauses will apply mainly to the packing of wrapped material; they are very
important as drifting free moisture can penetrate the overlaps of packing and contact
the contents so causing damage direct by contact, also creating internal sweating of
the material.
NB. Where wrapped goods are concerned many of the above mentioned clauses can
be used; for example, "Wrappers Rust Stained." Where galvanised material is
concerned the rust is referred to either as "White Oxidation Marks" or, when more
advanced, as "White Rust". It is important to mention drip down moisture runs when
these are observed.
Mechanical (handling) damages

Although at the time of loading these damages may be nothing more than
irregularities, they can eventually lead to damage developing and the goods must be
considered as not being altogether suitable perhaps for stowage purposes, or
capable of withstanding normal handling; the following clauses on Bills of Lading
should make this clear.
Unwrapped material
Hot rolled steel sheeting in coils
- "Inner and/or outer (or both) edges of plating locally dented and/or buckled where
handling gear marked (number of coils affected)."
- "Side edge windings locally affected by deep score marks." - "Inner and/or outer (or
both) turns of plating telescoped up to (give maximum extent of telescoping in
centimetres, also number of coils affected.)"
- "Telescoped edges of plating torn and bent (number of coils)."
44(49)
- "(Number of coils) loosely wound, windings slack, strapping bands slack; average
number of strapping bands per coil broken and/or missing."
- "Coil ovalised: note two way inner diameter measurements and mention numbers of
individual coils affected."
NB. The tightness of the windings of coils and efficiency of strapping is of

considerable importance. Loosely wound coils can lead to instability of the stow,
damage to the material and eventual costs for re-strapping in order to facilitate further
handling (for example, on carriage to final destination). The number of strapping
bands applied are the minimum; broken or missing strapping bands should not be
ignored.
No. 22 Hot rolled coils. Note bending damage to No. 23 Hot rolling coils -
inner circumference turns of plating excessive telescoping
Hot rolled steel plates in bundles

"Edges of bottom plates in bundles locally bent and/or buckled where handling gear
marked." "Edges of plating locally scored/gouged (number of bundles affected)."
Single steel plates

- "(Give number of plates). Plate edges locally bent where handling gear marked."
- "(Give number of plates). Plates waved/bent along length. Bent on end."
"Large steel beams"

These can be shipped in single pieces or wired into bundles. Overloading of slings
may cause bending of the flanges. When the goods are in bundle form, secured or
unsecured, it is important to observe how the flanges can lead to pressure in stow
resulting in serious distortion of the beam webs and such damage is not uncommon.
The flanges must not overlap consecutively but alternately. Steel beams are regularly
shipped in large quantities.
- "(Number of pieces) flanges incorrectly overlapping for stowage purposes."
- "(Number of pieces) flanges locally bent. Beams bent. Webs bent and/or distorted."
45(49)
No. 24 Large steel beams
Merchant iron
Small scantling material in the form of angles, flats, beams, rounds, squares,
channels, etc., shipped in lengths of 20 and 40 feet often form part of a cargo. They
are made up into unprotected bundles which are secured with flat metal strapping
bands or wire. If not well packed and tightly secured, in handling, individual pieces
project at the ends and become vulnerable to bending damages.
- "Bundles loosely secured."
- "Securing of bundles insufficient."
- "Individual pieces projecting on ends. Projected and pieces bent."
Pipes and tubes

The remarks above for Merchant Iron would apply to small scantling pipes made up
into bundles. If these pipes are fitted with plastic protection caps their condition
should be noted.
Single Mild Steel Pipes are shipped loose and in various lengths. Damages consist of
localised denting on the body of the pipe or on the ends. Ends can be completely
distorted so that the pipe in the affected area is out of round. If the ends of the pipes
are bevelled, ready for welding, the bevelled edges often become scored or
damaged (requiring rebevelling). It is customary to handle these goods with copper or
plastic lined lifting clamps/hooks. In the following the number of pipes affected should
be mentioned:
- "(Number) pipes locally dented in (number of places)."
- "(Number) pipes dented on one end. Out of round on one end."
- "(Number) pipes bevelled end scored, nicked, cut."
Specially coated pipes and cement lined pipes often form part of ship's cargoes.
Although such pipes are unprotected, damage to the coatings or even defects
caused in handling can provoke claims.
- "Cement lining affected by hair line cracks."
- "(Number) pipes cement coating chipped and/or locally broken on ends."
- "(Number) pipes protective coating locally scored, chafed where handling gear
marked."
46(49)
Wire rods
Unwrapped goods
Unwrapped wire rods are subject to claims for scoring, nicking, twisting and tangling.
Such wire has in many instances to undergo redrawing. Scoring and nicking may
result in the wire breaking in the dies and evidence of the defects is carried on in the
drawn material. Twisting and tangling causes delays on the production line. The
following clauses can be used:
- "Strapping bands slack and converging. Bundles slack and leaning to one side."
- "End windings twisted and/or tangled."
- "Percentage of visible windings nicked, scored, chafed."
No. 25 Wire rods: disintegration of bundles caused by bad stowage & rough
handling
Wrapped goods
Wrapped wire rods are usually destined for prestressing purposes, wire for musical
instruments and tyre cord, etc. Any defects whatsoever will undoubtedly result in
claims. This is delicate material and the following clauses can be used:
- "Packing locally chafed where handling gear marked."
- "(Number of coils) packing locally torn, partly torn, visible contents scored, chafed,
rusty."
Sheet pilings
Single and double sheet pilings have keying grooves on their edges. These
interlocking grooves must not sustain damage.
- "Keying grooves locally bent in (give number of positions)."
No. 26 Sheet pilings ready for shipment

47(49)
If uncoated, a normal rust clause will apply. If coated for protection, the following will
apply if the coat is defective:
- "Rust stained/rusty, where protective coating scratched, scored, gouged or chafed
away."
Wrapped material
Steel coils
- "Inner and outer edges of circumference packing dented and chafed where handling
gear marked."
No. 27 Steel coils - cold rolled steel strip sheet
Packages
- "Upper and lower edges of packing dented where handling gear marked."
No. 28 Packages - cold rolled sheets
General
- "(Side packing) (circumference packing) (inner core packing) (top packing) locally
dented / scored / torn open / contents exposed / visible plate edges buckled/ scored /
chafed / rusty."
- "(Number) strapping bands broken and/or missing."
- "Inner and/or outer circumferences plate edges telescoping, edges of plating
buckled/torn."
- "Coil (give package number) ovalised (give inner core diameter two way
dimensions)."
48(49)
Carriage of steel cargoes - Part 5

Responsibilities Under Charterparties
Types of contracts
In addition to the Bill of Lading (which evidences the contract of carriage between the
carrier and the cargo interests), there will often be a Time Charterparty or a Voyage
Charterparty, or both.
The Owner's obligations under the Hague or Hague-Visby Rules

The Bill of Lading will usually be subject to the Hague or Hague-Visby Rules. These
Rules will also often be incorporated in a Time Charterparty or Voyage Charterparty
by means of a Paramount Clause. Under the Hague or Hague-Visby Rules, the
Carrier, Owner or Disponent Owner has an obligation, before and at the beginning of
each voyage, to exercise due diligence (that is, reasonable care) to make the vessel
seaworthy. For these purposes, a vessel is not seaworthy if she is not cargoworthy.
In addition, the Rules impose a general obligation properly and carefully to load,
handle, stow, carry, keep, care for and discharge the cargo.
Loading, stowage and discharging operations

Time Charterparties
However, under most unamended Time Charterparty forms, it is the Charterer (rather
than the Owner) who is primarily responsible for loading, stowing and discharging the
cargo. Nevertheless, the Master is always entitled to supervise those operations and
there may be certain situations where responsibility shifts back to Owners (for
example, where the Master negligently intervenes in the operations or where there is
a problem, such as stability, which is particularly within the province of the Master). It
is, however, not unusual for Charterparties to be amended to make the Master
responsible for loading, stowage and discharge operations and, in those cases, the
responsibility is transferred, even where the stevedores are engaged by the
Charterer.
The NYPE Inter-Club Agreement

The position with regard to cargo claims is simplified under the NYPE form
Charterparty, if the contract incorporates the Inter-Club Agreement. Where this
Agreement is incorporated into the charter, the general rule is that the Owner will be
100% responsible for claims arising out of the vessel's unseaworthiness (or an error
or fault in the navigation of the vessel), the Charterers will be 100% responsible for
claims arising out of cargo handling (unless the charterparty is amended to make
these matters the Master's responsibility, in which case responsibility is apportioned
on a 50/50 basis), and shortdelivery and other claims will be apportioned on a 50/50
basis.
49(49)
Voyage Charterparties
Under a Voyage Charterparty the Charterer will be primarily responsible for loading,
stowage and discharging, if the contract provides for FIOS terms. If, however, the
contract provides for liner terms, then Owners will be primarily responsible for these
operations.
Conclusion
The above is a general description of the parties' obligations under Charterparties,
but in the event of a dispute or disagreement, it is essential to contact the Club (either
directly or through its Correspondents). Complex disputes and problems can arise
out of the carriage of steel cargoes. The Club has a vast array of technical and legal
advice at its disposal, not only to assist after a claim has arisen, but to assist in the
prevention of claims. In the event of uncertainty as to what should be done, the
Member should contact the Club. Skuld is there to help, as part of the Member's
team.

Carriage of Steel Cargoes, Guidelines

Uploaded by

Copyright:

Available Formats

Carriage of Steel Cargoes, Guidelines

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Carriage of Steel Cargoes, Guidelines

Uploaded by

Copyright:

Available Formats

1(49)

Carriage of steel cargoes - Index

PART 1 TYPES OF STEEL CARGOES

Category A - Packed or wrapped

PART 2 CARGO CARE

Section 1 - Loading and stowage

Section 2 - On the voyage

Supervision of loading, stowing and discharging

Section 1 - Pre-shipment survey - cargo

Information for the Surveyor

Section 2 - Pre-shipment survey - the vessel

Section 3 - Discharge survey

Section 4 - Cargo/commodity survey

Silver nitrate testing and sampling

PART 4 THE BILL OF LADING

Section 1 - The legal position

A "clean" Bill of Lading

Section 2 - Cargo condition clauses

Mechanical (handling) damages

PART 5 RESPONSIBILITIES UNDER CHARTERPARTIES

As part of the service offered to Members of Skuld, the Club operates a

A second objective is to help Members protect themselves from financial

We express our thanks to Arthur Sparks, of Sparks & Company Ltd.,

All previous steel circulars are superseded by this publication.

Oslo - January 1998

PART 1 TYPES OF STEEL CARGOES

Category A - Packed or wrapped

- Cold rolled steel sheeting in coils and packages.

- Coated steel in coils and packages; for example galvanised, aluminised

Packing is designed to protect the products from handling damage and

Category B - Not packed or wrapped

- Scrap: ferrous metal, borings, shavings, turnings,

- Care should be taken over ventilation.

- Check the temperature of the bulk ashore, before loading: if it is

- Cargo should be loaded, segregated, stowed and carried in accordance

Carriage of steel cargoes - Part 2 Cargo Care

Guidelines for Members, Masters and Surveyors

SECTION 1 - LOADING AND STOWAGE

Loading wet cargo

Rain during loading

Category B non-packed or non-wrapped products will often be stored on the open

A suitable descriptive clause (for example "Wet before Shipment") should be

Strength of tank tops

The permissible tonnage is calculated as follows:

Stowage and lashing of different types of products

As a general guide, the following weight/height ratio should be applied -

10 ton coils: 3 high

Bands/wires should be passed as in Drawings A and B.

No. 3 Steel coils recommended securing No. 4 Steel coils recommended

No. 5 Steel slabs awaiting shipment

Hot and cold rolled steel in packages and bundles

No. 10 Single hot rolled steel plates awaiting shipment

Before commencement of loading, 3"x3" dunnage in cross section should be laid in

Special care is needed in slinging. Braided slings are recommended, to avoid

No. 12 Pipes correctly bundled and strapped

The golden rules of stowage

PART 2 CARGO CARE

SECTION 2 - ON THE VOYAGE

Supervision of loading, stowage and discharging

The maintenance of the vessel