Manual Book Mesin Series 2500.PDF-1

PT.
JALA FUNGSI KREASINDO

J F
K
FASTENER - STUD WELDING EQUIPMENT & CONSUMABLES - FORM WORK SUPPLIES
SERIES 2500
Description :
Series 2500 is a fully regulated, single gun, solid -
State stud welding system primary intended for construction
job site application of large diameter stud and large volume -
industrial use. The weld timer is steplessy adjustable
beetwen 100 - 2000 M.sec. With current control steplessy
adjustable between 400 -2500 Amperes.
Standard Parts List

System Conguration
Item Description Part Number
1 Power/Control unit, 3 Phase/400 V 80 - 2500 - 010

Heavy Duty Gun PG-25
(80-025-010)
2 Extension Cable + Control Cable, 12 Meter 125 - 016 - 010 - Weldable Stud Range :
13-25 mm
3 Ground Cable and Clamp, 10 Meter, 95/125 mm 80 -120 - 010
- Length Welding Cable Gun :
4 Welding Gun
Heavy Duty Gun PG-25 80 - 025 - 010 1.5 Mtr
Standard Duty Gun PG-16 80 - 016 - 010 - Weight :
2.8 Kg (Excluding Welding Cable)
Standard Duty Gun -G-16

(80-016-010)
- Weldable Stud Range :
3-16 mm
- Length Welding Cable Gun :
6 Mtr
- Weight :
1.06 Kg (Excluding Welding Cable)
Technical Data Series 2500 Technical Data Series 2500

Stud Welding with Max. extention cable
cerramic ferrule permissible to mains
6 - 25 30
Weldable stud range connection (400 V mains,
( mm ) cross section identical to
mains extension cable)
Max. Current (A) 2500
Time-lag fuse for 400 V (A) 125
Stepless current Max. welding cable
Adjustment range, (A) 400 - 2500 length under given 2000 A/40 m
current (A) with at 120 mm
Stepless time given cross-section
adjustment range, 100 - 2000
(ms) Input voltage tolerance (%) -15/+16
Max. weld in rate in 30 Stud/6 mm Ip23
Class of protectin
studs/min. forstud 2 Stud/25 mm
( mm )
Cooling Fan
Input viltage, three-
400
phase 56/60 Hz (V)
Housing dimensions 1100 x 600 x
Mains plug 400V (A) 125 (L x W x H) mm 880
Mains cable 4-pole, 5/16 Weight (app.kg) 398

400 V (m/mm)
Jl. Tapos raya Kebayunan No. 23, Kebayunan Cimanggis Depok 16457
Telp. 021-87742795 Fax. 021-87742895
Website : www.jalafungsi.com Email : sales@jalafungsi.com
PT. JALA FUNGSI KREASINDO
J F
K
1.Introduction
With the Stud Welding Equipment you have purchased an appliance of superior quality. It has been
constructed according to latest technical principles and complies with all technical regulations and
requirements in force at the time of delivery. To achievetrouble-free operation at all times we recommended
that you observe the following
instructions:
- Before starting-up carefully read trought the complete manual and make sure that anyone on your staff
handling or operating the appliance has also read and understood the instruction.
- The safety instructions must be followed at all times.
- Store this manual in a safe place, with easy access for anyone operating the appliance.
- The appliance may only be operated by sufciently qualied personnel.
- Secure the machine against use by anauthorized persons.
- Have a trained electrician inspect the mains connection for correct fusing and aerthing.
- If any malfunctions occur which you cannot remedy yourself, call our after-sales service.
- In case of accidents call for proper medical help, and if necessary, notify accident insurers and/or
local trade supervision authorities.
1.1 Safety Instructions

The Series 2500 stud welding equipment and the welding gun PG-25 & PG-16 is designed for use in
drawn-arc stud welding only. It must not be used for any other purpose, with the exception of manual
electrode welding, and then only if the appliance is equipped for this purpose. In particular, welding under
water is strictly prohibited, nor is it permissible under any circumstances to use the appliance for thawing
up frozen water pipes.
1.1.1Personal Safety
Stud welding equipment and the welding guns PG-25 & PG-16 are approved for welding under increased
electrically hazardous conditions, according to EN 60974-1. For his own safety, the operator must wear
protective chloting during welding, which includes the following:
- Dry, insulating shoes

- Non-ammabe, dry, close-tting working clotes ( leather apron)
- Leather Gloves
- Safety goggles with an adequate degree of protection
- A special helmet with neck protrction while engaged in overhead welding
- No metallic jewellery (rings, chains, etc.) or watches may be worn during welding.
Telp. 021-87742795 Fax. 021-87742895
J F
K
During the welding process, persons wearing heart pace-maker must be kept at a safe
distance from the appliance and the welding cables, because the strong magnetic elds could endanger
their lives.In addition to the above, all normal accident prevention regulation must be observed.
1.1.2 safety When Working

- Do not operate the equipment in areas of re of explosion danger. Remove all inammable objects from
the surroundings!
- Keep in mind that welding splashes are likely to ignite inammable objects, for example cleaning rags
soaked with oil, grease or solvent or packing materials, event at several metres' distance!
- In case of doubt check with the security ofcer in charge and obtain his release before commencing work!
- Make sure that the operating site has sufcient ventilation!
- Do not weld without air axtrection on any workpieces which may release substances dangerous to healt,
such as coating materials, zinc, nickel, chromium or cadmium!
- Do not carry out welding on hollow objects which contain, or have contained, inammable liquids or gases,
or which are under pressure, or inside which a dangerous level of pressure can be generated by welding
heat!
- The heat generated by welding may lead to the release of gases or vapours which are dangerous to
health or even explosive. Specialized knowledge is required for this kind of work. Do not carry out such
operations unless you proses the necessary knowledge!
- Keep at a safe distance from any equipment which might be affected by magnetic elds, such us EDP
installations ( computers ), cards with magnetic strips, or timepieces (wrist-watches)
- Do not weld on the same workpiece (welding potential) simultaneouslywith other types of welding machines,
especially those working with different poles or frequency (alternating current), or welding equipment with
high voltage ignition, because this can adversely affect or damage the control unit of the stud welding
appliance.
- Ensure that a awless safe welding circuit is generated. The earthing cables should be rmly clamped
onto the workpiece. If this is not possible or not desirable, make sure that there are no parts in contact with
the welding circuit which can be damage or destroyed by the welding current, such us crane hooks, rolling
bearings, clamps with layers of partly insulating material, screw or rivets. Especially dangerous is the
destruction of protective conductors in other electric appliances when they come into contact whit the
welding current.
- Whenever the appliance must be placed on sloping ground, secure it against tipping over or rolling downhill.
Telp. 021-87742795 Fax. 021-87742895
J F
K
- For transporting the equipment, use only the parts specially provided for this purpose. When liftng it
by cran, this must be done buy using the crane lug. Before attaching it, make sure that the nuts are properly
tightened. The handles of the appliance are not designed for transporting it by crane.
- While setting up or adjusting the welding gun, unintentional triggering of the gun pushbutton must be
avoided, either by turning off the power switch or by disconnecting the control cable plug from the ange
socket on the power source.
2.Drawn Arc Stud Welding

Drawn-arc stud welding is used for the welding of metallic parts, generally of cylindrical shape, onto metallic
workpieces. For this purpose, a DC power source and a mobile device, the welding gun, are required.
Depending on the type of welding-pool protection and welding time range used, the appropriate process
may be stud welding with a ceramic ferrule.
The welding procedure is illustrated below:
Drawn-arc stud welding procedure
Explanation:
A : Stud welding with ceramic ferrule
F : Ceramic ferrule
P : Protrusion
L : Lift
A 1 : The stud contacts the aaaworkpiece.
A 2 : The stud is lifted of under current
Flow and thus the arc ignited.
A 3 : The drawn arc melts the tip of the
Stud and the portion of the
workpiece directly beneath it. At
the end of welding time the stud is
pressed ( plunged ) into themolten
part of the workpiece.
A 4 : The melt solidies, resulting in a rm
Cross-sectional weld. The ceramic
Ferrule is then removed.
Telp. 021-87742795 Fax. 021-87742895
J F
K
2.1 Technical Data on SERIES 2055 Power Sources
Technical Data Series Data
Stud Welding with ceramic Ferrule

6 25
Weldable stud range (mm)
Max. Current (A) 2500
Stepless current adjustment range, (A) 400-2500
Stepless time adjustment range, (ms) 100-2000
Max. weld rate in studs/min. for 30 Stud / 6 mm

stud (mm) 2 Stud / 25 mm
Input voltage, three-phase 50/60 Hz (V) 400
Mains plug 400V (A) 125
Mains cable 4-pole, 400 V (m/mm) 5/16
Max. extension cable permissible to 30

mainsConnection (400 V main,cross
section identical To mains extension cable)
Time-lag fuse for 400 V (A) 125
Max welding cable length under given 2000 A/40 m

Current (A) with given cross-section At 120 mm
Input voltage tolerance (%) -15/+6
Class of protection Ip23
Cooling Fan
Housing dimensions (L x W x H) mm 1100 x 600 880
Weight (app.kg) 398
Telp. 021-87742795 Fax. 021-87742895
J F
K
2.2 The Power Source Series 2500

The power source consists of a 3-phase transformer, a fully controlled thyristor bridge with constant
current control, a choke connected in series, and electronic control. The standard setting of the appliance
is for an input of 400 V (3-phase).
Nominal output of the equipment can still be reached with an udervoltage of up to minus 10%. However,
depending on circumstances, it it may become necessary to shorten the extension cables, to prevent
exceeding the capacity of the constant current control. If the input voltage drops below minus 15%, the
appliance can no longer be operated.
Because the load-voltage may be considerably lower than the no-load-voltage, especially in case of a
weak power supply, in a case of doubt a voltage measuring should be carried out during the welding
procedure.
When welding with 400 V input, the primary current is approximately 12% of the welding current. The
mains must be capable of supplying this primary current with minimum uctuation to voltage. Since the
ow of current is only short (max. 1.5 sec) main fuses of considerably reduced rating may be used,
provided, of course that they operate with sufcient time-lag. Quick acting fuses (including safety cut-out
switches) may prevent operation of the appliance.
An overvoltage of 15% should not be exceeded, since otherwise iron losses in the transformer will
cause overheating.
2.3 The Welding Gun PG-25

In drawn-arc stud welding the welding gun is used to generate the arc between stud and workpiece, and
to unite the two welding pools at the end of welding time. The PG-25, gun with length adjustment
especially for drawn arc stud welding. It should be used for studs with very variations in length and when
constant conditions for the positioning of the welding gun apply.
In stud welding, lift and protrusion are important parameters. In most cases they can be selected to t
stud diameters, the position of the weld or the kind of surface on the workpiece may necessitate some
adjustments. In such cases, optimal setting should be obtained through test welds. The length of lift is
the vital factor in determining the form of metal melting at the tip of the stud. In case of major deviation
from optimal values, cavities may form in the welding pool. Moreover, if if the lift is too small, an In crease
in the number of droplet short circuits will destabilize the welding process. The protrusion will determine
the form of the welding collar around the welded stud. In some cases,especially when welding onto
a vertical wall, setting other then those listed may be selected. If the plunge is too shallow, this will lead to
pores and undercuts in the weld zone. If it is too deep, the welding pool will splash out to the side or
upwards with the risk of blockage to the downward movement of the stud.
Telp. 021-87742795 Fax. 021-87742895
J F
K
2.4 Technical Data on Stud Welding Guns PG-25 (Heavy Duty Gun)
Technical Data PG-25
Stud Welding with ceramic Ferrule 13 -25

Standard support by ..legs 2
Lifting range from to (mm) 18
Input voltage of lifting coil )v=) 60 90
Welding cable (m/mm) 1.5/120
Welding cable plug ( mm) 120
Control cable plug 4-pole YES
Control cable (m/mm) 6/4 x 1.0
Length (excluding chuck) (mm) 240
Body diam. App.(mm) 80
Height (including handle) (mm) 170
Weight (excluding connection cables) app. (kg) 2.8
Telp. 021-87742795 Fax. 021-87742895
J F
K
2.5 Technical Data on Stud Welding Guns PG-16 (Standard Duty Gun)
Technical Data PG-16
Stud Welding with cerramic Ferrule 5 16

Short-Cycle stud welding 3-10

Standard support by.legs 2
Lifting range from..to(mm) 13
Input voltage of lifting coil (v=) 60 90
Welding cable (m/mm) 6/70
Welding cable plug (mm) 50
Control cable plug 4-pole YES
Control cable (m/mm) 6/4 x 1.0
Length (excluding chuck)(mm) 207
Body diam. App.(mm) 50
Height (including handle) (mm) 150
Weight (excluding connection cables)app. (kg) 1.05
Telp. 021-87742795 Fax. 021-87742895
J F
K
2.6 Setting Guidelines for welding with ceramic ferrule

The setting given in gure 2 have been tested for welds on clean metallic surfaces and standard type
studs in downhand position. The decisive parameter is the actual diameterat the welding end of the stud,
not the nominal diameter. Under different condition (other welding position, or oily, scaly or primer-coated
surfaces) the optimal setting must be determined by test welds. With difcult surfaces, it may be
necessary to considerably increase lift and welding time, and to reduce the welding current. When
welding in a horizontal position,it is recommended to select higher current and protrusion than the given
settings and at the same time reduce welding time and lift. Please note that at the lower end of the
welding range of large appliances it may be necessary to select values higher than those listed in the
chart. This is chaused by the relatively long phase for building up the current, which means that for a
considerable part of the welding cycle the peak current is not yet reached. This must be compensated
by lengthening the welding cycle or selecting a higher current.
APPROXIMATE SETTING
STUD TIME CURRENT

DIA. M. SEC AMP
6 100 400
8 200 600
10 240 700
12 300 800
16 550 1300
19 800 1700
22 1000 2000
25 1200 2300
Telp. 021-87742795 Fax. 021-87742895
J F
K
3.Working with the stud welding equipment

3.1 Requirements before starting-up
1.Ensure adequate power supply
2.The power connection must be earthed according to regulations.
3.The housing of the welding power source must not have any electrical contact with the workpiece.
Make sure that the insulating wheels (caters) are in perfect condition!
4.Make sure that the welding power source is standing rm a vibration-free, dry area!
5.Make sure that there is sufcient cooling! The circulation of air must not be restricted in any way.
6.Operating the equipment in a re or explosion danger area is prohibited. In case of doubt obtain
a release for the welding operation from the security ofcer in charge.
7.Keep a safe distance from any objects which may be affected by strong magnetic elds, such as
EDP installations!
Make sure that persons wearing a heart pace-maker do not come close to the welding cables!
3.2 Starting-up of the welding gun

1.While setting up or adjusting the welding gun, unintentional triggering of the gun pushbutton must
be avoided, either by turning off the power switch or by disconnecting the control cable plug from the
ange socket on the power source.
2.Screw the desired chuck on to the adapter screw of the gun, slightly tightening it with a wrench.
3.Using the counter-sink screws and washers supplied, attach the two legs to the desired footplate.
Initially, do not tighten the screws.
4.Insert the desired ceramic ferrule grip (when welding with a ceramic ferrule) or the supporting tube
(in case of short cycle welding) into the footplate, pushing it to the stop. Secure the ceramic ferrule
grip or the supporting tobe with the screws at the sides of the footpate.
5.Insert a suitable stud into the chuck, pushing it up to the stop.
6.Slide the footplate with the legs in the damping guides of the gun, so that the tip of the stud reaches
approximately the same height as the ceramic ferrule grip or the supporting tube.
7.Move the footplate until the stud is centrally seated in the bore of the ceramic ferrule grip or the
supporting tube. Then tighten the counter-sink screws of the footplate.
Telp. 021-87742795 Fax. 021-87742895
J F
K
Explanation :
A : Correct centering of the footplate
B : Inaccurate centering of the footplate
Will cause blockage of the pluging
Movement of the stud.
8.Only when welding with a ceramic ferrule: Place a suitable ceramic ferrule into its grip. Check the
centering of the footplate by manually pulling back the pistonof the gun and then slowly releasing it again.
The stud should then move forward without pushing the ceramic ferrule out of its guide. If the ceramic
ferrule is pushed out, loosen the footplate and improve its centering.
9. Slide the footplate with the legs in the damping guides until the correct protrusion is reached
Explanation:
1 : Chuck
2 : Stud
3 : Footplate
4 : Ferrule grip
5 : Leg
6 : Screw
L : Lift
P : protrusion
Diagram of the gun setup
3.3 Starting-up of the Power Source

1.Insert the mains plug into the socket and lock it into position using the lock ring (if available).
2.Connect the ground cable to the ground sockets of the welding power source and the workpiece.
The connection points on the workpiece must be bright metal. Lock the welding cable plugs by turning
them to the right (clockwise) to the stop
3.Connect the welding and control cables of the welding gun to the correct sockets of the power source,
using a welding cable extension if necessary. Lock the welding cable plugs by turning them to the right
(clockwise) to the stop.
Note: In most cases, the studs is connected to the minus pole and the workpiece to the plus pole. In
certain cases, especially when welding non-ferrous metals, reversed polarity may improve the welding
results. The power source is suitable for welding with either polarity. Before welding with the minus pole
connected to the workpiece, be sure to disconnected the second earth cable from the plus pole.
Telp. 021-87742795 Fax. 021-87742895
J F
K
4. Switch on the welding power source at its power switch. The green pilot lamp will light up and the
fan will start to operate.
3.4 Selecting of setting

Welding current and welding time are set on the control panel of the power source. When selecting
the welding time, note the position of the time range change-over switch. In the welding time gauge,
the uninterruptedline applies to the setting for ,, stud welding with ceramic ferrule.
3.5 Welding
Place the prepared gun on the workpiece so that the whole basis of the ceramic ferrule of supporting
tube touches the surface of the workpiece. In so doing, the piston is pushed back by the length of the
protrusion, and the tension spring is tightened.
Now press the trigger, holding the gun completely still during welding until the welding pool has cooled
down. Then lift off the gun from the welded stud, keeping it straight (i.e. in the axial direction of the stud)
and by turning it clockwise. If it is not lifted of straight, this may open out the gripping jaws of the chuck
and prevent a sufciently tight grip on the next stud to be welded or the chuck can get loose from the
adaptor screw.
Next, check the weld (by visual test and possibly other tests according to EN ISO 14555) and adjust
the settings if necessary.
Test welds should always be carried out prior to starting a series of welds.
3.6 Weld Testing

For testing a stud weld, there are several different methods available:
1.Visual test : A good weld will have a closed even weld collar with a shiny blue-gray surface, not
dull or porous.
The welded stud will have its nominal length 1 mm.
Explanation : Nominal length of stud

A : Good weld
B : Energy too high
C : Energy too low
Assessment of visual examination
Telp. 021-87742795 Fax. 021-87742895
J F
K
A frwquent fault is a so=called pluging impediment. It occurs whenever the pluging movement of the stud
is cut short and the stud comes to a halt above the welding pool. In case of only a minor impediment the
pluging of the stud may not be stpooed, but delayed. In this case a cold weld with an
incompleteconnection may result, without any faults showing on the outside. Therefore the nal
assessment of aweld should never be made on the basis of visual test alone, without mechanical
test being carried out as well.
2.Bend Test : A awless weld will withstand bending by an angle of up to 60 without any cracks in the
welding zone. This does not apply for studs designed for heat-resistant steel) and for studs with
non-uniform cross section. The bend test is carried out to check the suitability of both the selected
settings and the combination of materials welded together.
Bending by = 60o with a hammer or an afxed pipe

(for leverage). Result satisfactory, if the welding zone or the
heat affected zone shows no cracks or breakages.
Carrying out a bend test
Telp. 021-87742795 Fax. 021-87742895
J F
K
Illustrates the assessment of welding result.

Assessment of stud welds
Appearance Remarks
Good weld with ceramic ferrule
Lopsided melting because of arc-blow effect.

This can be remedied by adjusting the earth
clamps, by providing compensating masses
at the rim, or by turning the gun (if the
welding cable is on the outside).
A large lift and welding without ceramic
ferrule will increase the blowing effect.
Impediment to the pluging of the stud.

Possible causes:
1.Friction between stud and ceramic ferrule
due to inaccurate centering of the footplate
or welding splashes (energy too high)
2.Droplet short-circuits between the stud and
the workplace due to too low lift setting
3.Defective gun or damping set too high.
Implediment to the pluging of the stud (cold

pluging). The fault can only be recognized by
mechanical testing; if bent only by a small
angle, the stud will break off at the welding
zone. At the edge of the stud and the welding
zone blank spots are visible (lack of fusion).
Possible causes: As given above
Further details about testing and assessments of stud welds are available
Telp. 021-87742795 Fax. 021-87742895
J F
K
Illustrates the assessment of welding results.

Effect of arc blow and some possible remedies
No Cause Remedy
Note : Arc blow is proportional to the current intensity and can be inuenced by
symmetrically attaching the mass clamps and by attaching compensating masses or
(in the case of hand guns with an external welding cable) by turning the gun about the
vertical axis. It generates one-sided melting and can increase the number of pores in the
welded materials.
Telp. 021-87742795 Fax. 021-87742895
J F
K
3.7 shutting-Down
After termination of welding the power switch must rst be turned off. In case of interruption for any length
of time, the appliance should also be disconnected from the mains (i.e. by pulling out the plug). Never use
the mains plug in lieu of a switch, i.e. before disconnecting it, the power switch must be turned off rst.
4.Remedies for Malfunctions

In case of malfunctions recognized by the machine itself, the red signal lamp for error will light up.
The kind of malfunction present can be identied. As soon as the error is identied, the red light will ash.
The following error signals are possible.
4.1 Error of the Power Source
Cause Remedy
Excessive current in lifting circuit (short - Repair or replace contol cable.
circuiting in the control cable or lifting coil Repair or replace welding gun.
burn out)
Overheating of the Power Source (Yellow Let the appliance cooling down with
lampon the control panel signal the fan switch on.
Overheating of the thrystor bridge Reduce welding performance.
Main phase missing Replace fuses (use only fuses with

sufcient time lag). Make sure the
capacityof the fuses used is
adequated.
Pilot current insufent (leads to ignition Replace pilot current contractor,

problems), pilot current contractor defect replace pilot current fuses.
or pilot current fuse burnt out
Internal control error Replace control module.
Telp. 021-87742795 Fax. 021-87742895
J F
K
4.2 Other Malfunctions

In the following chart, some malfunctions are described which can be recognized and remedied by
qualied personel with relative ease. In case you cannot solve these problems yourself, please contact
our agent in your neighbourhood or our customer service department. It is important that you give us
detail of type and series number of your appliance, as well as an exact description of the malfunction.
Maffunction Maffunction Maffunction
Piston of the gun does Disconnection in the control

not react to triggering cable to the gun First connect the gun direcly to the power
sourceand trigger it once more. If the
malfunction does not occur again, the fault
is in the control cable extension. If the
malfunction occurs again: check the gun
with an Ohm-meter. Normal resistence of
the coil is app. 20 ( PG-16 app. 38 ).
The magnet is connected to points 1 and
2, the trigger to 3 and 4 if the fault is still
not remedied, the plug and socket
connection should be check next.
Fuse 2.5 A defected Replace it

Magnetic coil under Turn off the power source, then switch it
continouscurrent. on again watc ing the piston of the gun
(Do not trigger it). The piston must remain
unmoved. If the magnet attracts it
immediatelly, there is defect in the control.
Note : the magnetic coil will burn out if
kept continously under current even for a
short time
Faulty welding result in surface of the workpiece clean the surface of the workpiece in the
spite of correctly set oily, greasy, rusty, inccoated, welding area and at the ground connecting
welding parameters or painted, etc. point. The best result are obtained on
bright metal surface. On zinc-coated parts,
only welding without cerramic ferrule
(short cycle stud welding) will produce
satisfactory result.
Telp. 021-87742795 Fax. 021-87742895
J F
K
Malfunction Cause Remedy
Welding result unreli-able Function of gun irregular After operating the gun for a longer
(sometimes goodsemetimes period,deviation in the lift wil
bad) increase. Generally, it willbe below
the selected setting. This mean an
increase in the number of droplets
short-circuitsand spalshes.
Because of the lower voltage in
thearc, the energy remains below
the desired level.Have the gun
repair by uor customer service.
Welding time is cutshort when when connecting the Connect cable correctly. Please
the triggerbutton is controlcable, the positions of note :When the trigger button is
releasedduring welding twolines were reversed held down through outthe welding
time, this malfunction will not
occur,however the trigger will be
the subjected toconsiderable
electrical strain. If the trigger
buttonis released during welding,
this will immediatelyinterupt the
welding proces. When cable
arecorrectly connected,the welding
process will not be inuenced by
how long the trigger is held
(provided it is held for at least
app.0.5 sec).
Ignition failure duringpiston lift- interruption of the pilot Make sure that the tip of the stud
off arcthrough inadwquate in direct contactwith the workpiece.
contactwith the tip of the stud This kind of the
malfunctionfrequently occurs
during welding of the headedstuds
to prick punch marks, whenever
there isinsufcient contact between
the alumnium tipand the workpiece.
Unussually earlypower source Fan does not runction. Check fuse 1A.
cut-outbecause of powerheating
Unussually strong heating up at Reduction of the cross-section Stop welding immediately !

somepoints of the welding circuit through patrialwire break-age, Replace cables !tighten all
scorching at loose connections connections within the
weldingcircuit !
Telp. 021-87742795 Fax. 021-87742895

Manual Book Mesin Series 2500.PDF-1

Uploaded by

Copyright:

Available Formats

Manual Book Mesin Series 2500.PDF-1

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Manual Book Mesin Series 2500.PDF-1

Uploaded by

Copyright:

Available Formats

PT.

JALA FUNGSI KREASINDO

Standard Parts List

1 Power/Control unit, 3 Phase/400 V 80 - 2500 - 010

Standard Duty Gun -G-16

Technical Data Series 2500 Technical Data Series 2500

Mains cable 4-pole, 5/16 Weight (app.kg) 398

1.1 Safety Instructions

- Dry, insulating shoes

1.1.2 safety When Working

2.Drawn Arc Stud Welding

Drawn-arc stud welding procedure

2.1 Technical Data on SERIES 2055 Power Sources

Technical Data Series Data

Stud Welding with ceramic Ferrule

Max. Current (A) 2500

Stepless current adjustment range, (A) 400-2500

Stepless time adjustment range, (ms) 100-2000

Max. weld rate in studs/min. for 30 Stud / 6 mm

Input voltage, three-phase 50/60 Hz (V) 400

Mains plug 400V (A) 125

Mains cable 4-pole, 400 V (m/mm) 5/16

Max. extension cable permissible to 30

Time-lag fuse for 400 V (A) 125

Max welding cable length under given 2000 A/40 m

Input voltage tolerance (%) -15/+6

Class of protection Ip23

Housing dimensions (L x W x H) mm 1100 x 600 880

Weight (app.kg) 398

2.2 The Power Source Series 2500

2.3 The Welding Gun PG-25

Technical Data PG-25

Stud Welding with ceramic Ferrule 13 -25

Standard support by ..legs 2

Lifting range from to (mm) 18

Input voltage of lifting coil )v=) 60 90

Welding cable (m/mm) 1.5/120

Welding cable plug ( mm) 120

Control cable plug 4-pole YES

Control cable (m/mm) 6/4 x 1.0

Length (excluding chuck) (mm) 240

Body diam. App.(mm) 80

Height (including handle) (mm) 170

Weight (excluding connection cables) app. (kg) 2.8

Technical Data PG-16

Stud Welding with cerramic Ferrule 5 16

Short-Cycle stud welding 3-10

Standard support by.legs 2

Lifting range from..to(mm) 13

Input voltage of lifting coil (v=) 60 90

Welding cable (m/mm) 6/70

Welding cable plug (mm) 50

Control cable plug 4-pole YES

Control cable (m/mm) 6/4 x 1.0

Length (excluding chuck)(mm) 207

Body diam. App.(mm) 50

Height (including handle) (mm) 150

Weight (excluding connection cables)app. (kg) 1.05

2.6 Setting Guidelines for welding with ceramic ferrule