FEATURES COMPUTER START / STOP KM / MILE SELECTION

ATTENTION: Computer Functions refer to the packing details. Slide the computer onto the mounting bracket until it snaps To start the unit, press the RIGHT button to turn on the display After the wheel size input, the following function is selection of
firmly into position. Press the release button to take out the and the wireless mounting system. To stop the unit, leave kilometers or miles as the measurement for distance. Press the
FUNCTIONS 9 computer as shown in Fig. 1. unused for over 5-6 minutes and then the computer will RIGHT button to choose between kilometer (KM) and Mile (M),
Speedometer (SPD) automatically switch off to preserve batteries. press the LEFT button to confirm.
- 0~99.9 KM/hr or M/hr
Tripmeter (DST)
- 0~999.9 KM or M Fig. 1
WHEEL SIZE INPUT SPEED COMPARATOR
Odometer (ODO) Press and hold LEFT and RIGHT buttons for 2 seconds or after A + or - sign appears to the right of the
- 0~9999.9 KM or M the replacement of battery, the unit is switched to wheel size speed. + indicates you are travelling
Auto Trip Timer (TM) input mode. Multiply wheel diameter, d (Fig. 2) in millimeters by faster than your average speed (AVS). A
- 9: 59 59 3.1416 to determine wheel factor, c. - indicates you are riding slower than your
Maximum Speed (MXS) Press the LEFT button to select digit to be input and the RIGHT average speed.
- 0~99.9 KM/hr or M/hr button to adjust the digit to the desired number (hold for fast
Average Speed (AVS) advance). Press the LEFT button again to KM/MILE selection.
- 0~99.9 KM/hr or M/hr (Note: removing battery will erase Wheel Size Input)
Scan
- for DST, MXS, AVS, TM For convenience you can refer to the chart of wheel diameter
size factor inputs.
SPEEDOMETER (SPD)
Speed Comparator
- (+ or -) Instantaneous Speed is indicated on the
top line. The range of measurement is
Digital Clock from 0 to 99 KM/ hr [0 to 99 M/ hr] and
accuracy is 0.5 KM/ hr [M/ hr].
Fig. 2
650A
(700x23C)

ODOMETER (ODO)
Total distance travelled is indicated by
distance in millimeter ODO and display on the bottom line. To
per one turn reset ODO, press and hold LEFT and
Release RIGHT buttons for 2 seconds or remove
the battery.

ATTENTION !! Refer to the appendix for installation reference.

TRIPMETER (DST) TRIP TIMER (TM) SCAN

(Trip Information Reset Mode)
Trip distance measurement is indicated by
Trip timer measurement is indicated by TM
and is displayed on the bottom line. Trip
The Scan mode allows DST, MXS, AVS
and TM to cycle on the screen without SERFAS CYCLE
COMPUTER
DST and is displayed on the bottom line. Timer is activated automatically with pressing any keys.
Tripmeter is activated automatically with speedometer input [On when you ride and
speedometer input. Reset DST to zero by off when you stop.] It records only the time
pressing the LEFT button for 2 seconds; spent actually riding.
DST (Trip distance), TM (Trip Timer) & AVS Reset TM to zero by pressing the LEFT
(Average Speed) will also be reset at that button for 2 seconds in DST mode.
time.

MALFUNCTION PROBLEM
Inaccurate maximum Unknown atmospheric or RF
MAXIMUM SPEED (MXS) speed reading interference
CLOCK (12H / 24H) Maximum speed measurement is indicated
A 12 or 24-hour digital clock is indicated by No speedometer Improper magnet/transmitter
by MXS and is displayed on the bottom reading alignment
the flickering colon on the bottom line. To line. Maximum speed is stored in memory
switch between the 12 and 24 hour format Check battery and correct
and updated only when a higher speed is installation
or to adjust time, press the LEFT button for reached. To reset MXS, press and hold the
2 seconds. 24H will start to flicker. Use RIGHT button to enter AVS mode.
the RIGHT button to select 12H for12- Slow display Temperature outside of operating
hour format or 24H for 24-hour format. response limits (0-55 C)
Press the LEFT button to confirm. Next the
hour digits will start to flicker. Use the Black display Temperature too hot, or display
RIGHT button to select the hour. To change exposed to direct sunlight too long
minutes, press LEFT button again. The AVERAGE SPEED (AVS)
minutes will start to flicker. Use the RIGHT No trip distance Check correct transmitter / magnet
Average Speed measurment is indicated reading alignment Check battery and correct
button to select the minutes. Press the
by AVS and is displayed on the bottom line. installation
LEFT button once more to return to
AVS is calculated with the Trip Timer (TM),
CLOCK Mode.
so AVS is the average speed only while Display shows Take out computer battery and
riding. irregular figures install again

Art No.: BC-9-P3-GB

INSTRUCTION MANUAL