Data sheet

Customer item no.:

Communication dated: 12/11/2015 Number: 9973069649
Doc. no.: B1509282 Item no.: 100
Quantity: 1 Date: 16/11/2015
Page: 1 / 4

Sewabloc F 50-250GH H 100L 04 Version no.: 3

Operating data
Requested flow rate 30.00 m/h Actual flow rate 30.36 m/h
Requested developed head 10.00 m Actual developed head 10.24 m
Pumped medium Water Efficiency 46.8 %
Clean water Power absorbed 1.80 kW
Not containing chemical and Pump speed of rotation 1674 rpm
mechanical substances which NPSH required 1.14 m
affect the materials Permissible operating 10.00 bar.g
Ambient air temperature 20.0 C pressure
Fluid temperature 20.0 C Discharge press. 1.00 bar.g
Fluid density 998 kg/m

Fluid viscosity 1.00 mm/s Shutoff head 14.07 m

Suction pressure max. 0.00 bar.g Max. allow. mass flow 13.65 kg/s
Mass flow rate 8.42 kg/s Design Single system 1 x 100 %
Max. power on curve 2.48 kW Tolerances to ISO 9906
Class 3B; below 10 kW acc.
to paragraph 4.4.2

Design
Pump standard KSB-Aggregate international Manufacturer KSB
execution Type MG
Design Close-coupled Material code SIC/SIC/NBR
Orientation Horizontal Impeller type Free flow (vortex) impeller (F)
Suction nominal dia. DN 65 Wear ring Casing wear ring
Suction nominal pressure PN 16 Impeller diameter 170.0 mm
Suction position axial Free passage size 25.0 mm
Discharge nominal dia. DN 50 Direction of rotation from Clockwise
Discharge norminal pressure PN 16 drive
Discharge position top (0/360) Bearing bracket size B01
Discharge flange drilled EN 1092-2 Bearing type Anti-friction bearings
according to standard Lubrication type Grease
Flanges DN 65 will be drilled with 4 holes Color Ultramarine blue (RAL 5002)
Suction nozzle drilled acc. to DIN2501 with tapped blind holes KSB-blue
Shaft seal 2 mech. seals in tandem
arrangement with oil reservoir
Data sheet

Customer item no.:

Communication dated: 12/11/2015 Number: 9973069649
Doc. no.: B1509282 Item no.: 100
Quantity: 1 Date: 16/11/2015
Page: 2 / 4

Sewabloc F 50-250GH H 100L 04 Version no.: 3

Driver, accessories
Baseplate type Sewatec foundation rails Available reserve 66.27 %
Baseplate size U80X550b Rated current 9.7 A
Starting current ratio 9
Scope of mounting parts: foundation rails.
Driver type Electric motor Insulation class F to IEC 34-1
Drive standard mech. IEC Motor enclosure IP55
Drive standard elec. IEC Cos phi at 4/4 load 0.74
Model (make) KSB-Motor Motor efficiency at 4/4 load 89.5 %
Drive supplied by Standard motor supplied by Temperature sensor 3 PTC resistors
KSB - mounted by KSB Motor winding 460 / 795 V
Motor const. type V1 Number of poles 4
Motor size 100L Connection mode Delta
Efficiency class Efficiency class IE3 acc. to Motor cooling method Surface cooling
IEC60034-30-1 Motor material Aluminium
Motor speed 1674 rpm Frequency inverter operation FI allowed
Frequency 60 Hz allowed
Rated voltage 460 V Motor noise pressure level 65 dBa
Rated power P2 3.00 kW

Materials GH
Notes Impeller (230) High Chrome white iron EN-
General criteria for a water analysis: pH-value >= 7; chloride GJN-HB555(CR14)
content (Cl) <=250 mg/kg. Chlorine (Cl2) <=0.6 mg/kg. O-Ring (412) Nitrile rubber NBR
Pump casing (101) Grey cast iron EN-GJL-250 Casing wear ring (502.1) Grey cast iron EN-GJL-250
Discharge cover (163) High Chrome white iron EN- Screwed plug (903) Steel ST
GJN-HB555(CR14) Hexagon socket head cap Chrome steel CrSt
Shaft (210) Chrome steel 1.4021+QT800 screw (914)
Performance curve

Customer item no.:

Communication dated: 12/11/2015 Number: 9973069649
Doc. no.: B1509282 Item no.:100
Quantity: 1 Date: 16/11/2015
Page: 3 / 4

Sewabloc F 50-250GH H 100L 04 Version no.: 3

20
Total developed head

[m]

200.0
10

170.0

150.0

0
0 10 [m/h] 20 30 40 50 60 70

2
NPSH req.

[m]

0 10 [m/h] 20 30 40 50 60 70

40
Efficiency

[%]

20

0
0 10 [m/h] 20 30 40 50 60 70
Power Input

[kW]

0 10 [m/h] 20 30 40 50 60 70
Flow

Curve data
Speed of rotation 1674 rpm Efficiency 46.8 %
Fluid density 998 kg/m Power absorbed 1.80 kW
Viscosity 1.00 mm/s NPSH required 1.14 m
Flow rate 30.36 m/h Curve number K42651
Requested flow rate 30.00 m/h Effective impeller diameter 170.0 mm
Total developed head 10.24 m Acceptance standard Tolerances to ISO 9906
Requested developed head 10.00 m Class 3B; below 10 kW
acc. to paragraph 4.4.2
Installation plan

Customer item no.:

Communication dated: 12/11/2015 Number: 9973069649
Doc. no.: B1509282 Item no.:100
Quantity: 1 Date: 16/11/2015
Page: 4 / 4

Sewabloc F 50-250GH H 100L 04 Version no.: 3

. 620

100 230
155 155
20
DN2

.
225

DN1
198

1] 170

125
14
47.5 15 80

18 250
95
320
125

550

1] The inlet flange spacer is available as an accessory

Drawing is not to scale Dimensions in mm

Motor Connections
Motor manufacturer KSB-Motor Suction nominal size DN1 DN 65 / EN 1092-2
Motor size 100L Discharge nominal size DN2 DN 50 / EN 1092-2
Motor power 3.00 kW Nominal pressure suct. PN 16
Number of poles 4 Rated pressure disch. PN 16
Speed of rotation 1674 rpm Flanges DN 65 will be drilled with 4 holes
Suction nozzle drilled acc. to DIN2501 with tapped blind
Baseplate holes
Design Sewatec foundation rails
Size U80X550b
Material Steel ST
Leakage drain baseplate Rp1, Without
(8B) Weight net
Pump 70 kg
Baseplate 10 kg
Motor 34 kg
Total 114 kg
Connect pipes without stress or strain! For auxiliary connections see
Dimensional tolerances for shaft axis height: DIN 747 separate drawing.
Dimensions without tolerances, middle tolerances to: ISO 2768-m
Connection dimensions for pumps: EN735
Dimensions without tolerances - welded parts: ISO 13920-B
Dimensions without tolerances - gray cast iron parts: ISO 8062-CT9