QuickSilver Controls QCI-DS008 QCI-A23

Datasheet:QCI-DS008 QuickSilver Controls, Inc.
Date: 25 June 2010 www.QuickSilverControls.com
NEMA 23 I-Grade Motor/Encoder
Shaft Seal (QCI-23M-65)

sold separately
Property of QuickSilver Controls, Inc. Page 1 of 14 This document is subject to change without notice.
QuickControl and QCI are Registered Trademarks of QuickSilver Controls, Inc.
SilverLode, SilverNugget, SilverDust, PVIA, QuickSilver Controls, and AntiHunt are trademarks ofBy:
Sold & Serviced
QuickSilver Controls, Inc.. ELECTROMATE

Toll Free Phone (877) SERVO98
Toll Free Fax (877) SERV099
www.electromate.com
sales@electromate.com
Note: Motor specifications (including torque curves) are only true when the motors are used in
conjunction with QuickSilvers SilverLode Controller/Drivers (i.e. SilverNuggetTM and
SilverDustTM). See the controller datasheets for more details.
General Motor Specifications
Specifications 23L-1 23K-3 23L-3 23H-5 23H-1 23-3 23H-3 23-5 23T-7
Maximum Speed (RPM) 4000 2000 4000 4000 4000 2000 4000 2000 1000
48v Optimal Speed (RPM) 2500 600 1900 1000 2500 500 1500 200 400
Torque (oz-in / Nm) 30 130 55 120 30 110 43 225 220

at Optimal Speed 0.22 0.92 0.39 0.85 0.22 0.78 0.30 1.60 1.55
Continuous Stall Torque 40 145 84 190 40 125 70 240 300
oz-in / Nm 0.28 1.00 0.59 1.34 0.28 0.88 0.51 1.70 2.1
Peak Power
80 58 84 95 78 47 60 47 65
(Mech. Watts)
0.74 0.74 3.2
Rotor Inertia 1.50 1.50 2.3 1.36 1.60 2.3
2 2 1.35E- 1.35E- 5.9E-
oz-in / Kg-m 2.7E-5 2.7E-5 4.2E-5 2.5E-5 2.9E-5 4.2E-5
5 5 5
Weight 1.40 1.70 1.70 2.6 1.40 1.70 1.70 2.6 3.2
pounds / Kg 0.65 0.77 0.77 1.20 0.65 0.77 0.77 1.20 1.45
Maximum Driver Input
4.0 3.0 3.5 4.0 4.0 3.0 4.0 3.0 3.0
Current (Amps - DC)
Maximum Radial Force(lbs)
15 15 15 N/A N/A N/A N/A N/A 20
0.55 from mounting face
Maximum Axial Force (lbs) 13 13 13 N/A N/A N/A N/A N/A 6
Use Use Use Use

Notes 23L-1 23K-3 23L-3 23H-5
EOL EOL EOL EOL
Note: The grayed items are special order only. EOL = end of life, no new orders, information
provided for reference only.
Torque Curves
48V Max is the torque of the motor when the Torque Limits (TQL) command is set to Max
(see SilverLode Command Reference for details on the TQL command). Operating the motor
in this mode requires proper heat sinking on the Controller/Driver and motor to prevent
overheating.
All other torque curves represent motor torque at the specified voltage when the TQL
command is set to 100%. These curves represent torque up to 100% duty cycle depending
on ambient temperature, heat sinking and air flow.
Important: There is a slight reduction in available torque if the shaft seal (sold separately) is
used due to the resistance of the quad seal around the shaft. Sold & Serviced By:
QuickSilver Controls, Inc. Page 2 of 14 ELECTROMATE

www.electromate.com
Optimal Speed point provides the maximum available power at 100% torque setting, which
is usually the maximum efficiency point as well. If these two points differ, the Optimal speed
is approximately the average of the two speeds.
23L-1 Torque Curve

70
450
60
400
50 350
Torque (mN-m)
Torque (oz-in)
300
40
250
30
200
150
20
100
10
50
0 0
0 500 1000 1500 2000 2500 3000 3500 4000
Speed (RPM)
48V 36V 24V 12V 48V Max
23K-3 Torque Curve

180
1.2
160
140 1
120
Torque (oz-in)
Torque (N-m)
0.8
100
0.6
80
60
0.4
40
0.2
20
0 0
0 200 400 600 800 1000 1200 1400 1600 1800 2000
Speed (RPM)
48V 36V 24V 12V 48 V Max
Sold & Serviced By:

www.electromate.com
23H-5 Torque Curve

300
250
1.5
200
Torque (oz-in)
Torque (N-m)
150
1
100
0.5
50
0 0
0 500 1000 1500 2000 2500 3000 3500 4000
Speed (RPM)
48V 36V 24V 12V 48V MAX
Sold & Serviced By:

www.electromate.com
23H-1 Torque Curve

70
450
60
400
50 350
Torque (mN-m)
Torque (oz-in)
300
40
250
30
200
150
20
100
10
50
0 0
0 500 1000 1500 2000 2500 3000 3500 4000
Speed (RPM)
48V 36V 24V 12V 48V Max
23-3 Torque Curve

160
140 1
120
0.8
Torque (oz-in)
Torque (N-m)
100
0.6
80
60
0.4
40
0.2
20
0 0
0 200 400 600 800 1000 1200 1400 1600 1800 2000
Speed (RPM)
48V 36V 24V
12V 48 V Max
Sold & Serviced By:

www.electromate.com
23H-3 Torque Curve

120
800
100 700
600
80
Torque (mN-m)
Torque (oz-in)
500
60
400
300
40
200
20
100
0 0
0 500 1000 1500 2000 2500 3000 3500 4000
Speed (RPM)
48V 36V 24V 12V 48 V Max
23-5 Torque Curve

300
250
1.5
200
Torque (oz-in)
150 Torque (N-m)

1
100
0.5
50
0 0
0 200 400 600 800 1000 1200 1400 1600 1800 2000
Speed (RPM)
48V 36V 24V 12V 48 V Max
Sold & Serviced By:

www.electromate.com
23T-7 Torque Curve

400
350 2.5
300
2
Torque (oz-in)
Torque (N-m)
250
1.5
200
150
1
100
0.5
50
0 0
0 100 200 300 400 500 600 700 800 900 1000
Speed (RPM)
48V 36V 24V 12V 48V MAX
Sold & Serviced By:

www.electromate.com
Electrical Specifications
Encoder Interface
Encoder Count Per Revolution: 8000
Index Pulse: 49 - SilverLode controller/drivers internally translate to a single index pulse.
Motor Memory
I-Grade motors come from the factory with a memory chip containing encoder and motor
information. This information is automatically uploaded by the SilverDust IG/IGB
controller/driver to simplify the initialization process.
Temperature Sensor
All QCI IP65 motors contain a sensor to read motor temperature. This sensor automatically
reads in the background when controlled by a SilverDust IG/IGB controller/driver.
Temperature can be read from a dedicated register and/or used to halt the servo in the case of
an over temperature condition.
Connector Data
Standard
Motor Phase A+ 6
Motor Phase A- 11
Motor Phase B+ 1
Motor Phase B- 7
Motor Body Ground 12
2
Encoder Z 8
Encoder B 13
Encoder +5v 3
Encoder A 9
Encoder GND 14
Encoder A- 4
Encoder Z/ 10
Reserved 15
Encoder B- 5
Sold & Serviced By:

www.electromate.com
-6T Option
Pin Signals
EXPOSED FRONT VIEW OF MOTOR CONNECTOR
A Motor A -
C +5V
E Memory
G Motor B+
J Motor B -
L Motor A+
M Z+
N Z-
O A+
P B-
R B+
S GND
T A-
U Motor GND
Sold & Serviced By:

www.electromate.com
Mechanical Specifications
Standard
n.20 n5.1 mm
1.86 47.2 mm 2.25 57.2 mm
n1.500 n38.10 mm
1.86 47.2 mm
2.25 57.2 mm
See Notes
** .250 6.35 mm
.75 18.9 mm
.06 1.5 mm .19 4.8 mm
See Length Table
2.26 57.4 mm
2.40 61.0 mm
Motor Series Length Shaft diameter Notes **

23L-1 2.7 [68 mm] .250 [6.35 mm] Shaft has .020 [.5 mm] flat
23K-3 3.2 [81 mm] .250 [6.35 mm] Shaft has .020 flat
23L-3 3.2 [81 mm] .250 [6.35 mm] Shaft has .020 flat
23H-5 4 [101 mm] .250 [6.35 mm]
23H-3 3.2 [80 mm] .250 [6.35 mm] * Special order item
23-5 4.1 [103 mm] .250 [6.35 mm] * Special order item
23T-7 5.1 [129 mm] .3125 [7.94 mm] * Special order item
Sold & Serviced By:

www.electromate.com
-6T Option
n.20 n5.1 mm
1.86 47.2 mm
2.25 57.2 mm
n1.500 n38.10 mm
1.86 47.2 mm
2.25 57.1 mm
** .25 6.4 mm
.75 19.1 mm
.06 1.5 mm .19 4.8 mm
See Length Table
2.40 61.0 mm
2.26 57.4 mm
2.9 74 mm
Motor Series Length Shaft diameter Notes **

23L-1 3.1 [78 mm] .250 [6.35 mm] Shaft has .020 [.5 mm] flat
23K-3 3.6 [91 mm] .250 [6.35 mm] Shaft has .020 flat
23L-3 3.6 [91 mm] .250 [6.35 mm] Shaft has .020 flat
23H-5 4.4 [111 mm] .250 [6.35 mm]
23T-7 5.5 [139 mm] .3125 [7.94 mm] * Special order item
Note: The motor construction uses a wave spring to compensate for mechanical
tolerances and thermal expansion in the axial shaft direction. It is important to not push
the shaft into the motor in operation or when mounting gears or pulleys as this may
damage the encoder disk.
Sold & Serviced By:

www.electromate.com
Environmental Specifications
Operational Temperature
-10 C to +80 C
Storage Temperature
-40 C to +85 C
Humidity
Continuous specification is 95% RH non-condensing.
Shock
Limitation is approximately 50g/11ms.
IP Rating - Standard
IP50
IP Rating 6T Option
IP65 is achieved if both a shaft seal and IP65 Motor Interface Cable (QCI-C-D15P-T14S-nn)
are used.
NOTE: The IP65 rating is for applications with occasional wash downs. It is not meant for
continuous wet applications or high-pressure wash downs. See IP65 spec for more details
(CEI IEC 529).
Sold & Serviced By:

www.electromate.com
Recommended Components
Start-Up Kit
There are several start-up kits available, each based off a servo controller/driver. With a Start-
Up kit, power supply and motor/encoder, you will have everything you need to get started. See
the Start-Up Kit technical documents on our website for more details.
If you would rather buy the components individually, QCI recommends the following:
SilverNugget N2 Controller/Driver (QCI-N2-E3-04-EE) or

SilverDust D2 IG/IGB/IG8/IGF/IGC Controller/Drivers
(i.e. QCI-D2-IG, QCI-D2-IGB, QCI-D2-IG8,QCI-D2-IGF, QCI-D2-IGC)
The motors will work with any of the following controller/drivers. See the indicated datasheets
for details:
SilverDust D2 IGB (QCI-DS003)
SilverNugget I-Grade N2 (QCI-DS005)
SilverDust D2 IG8 (QCI-DS018)
SilverDust D2 IG (QCI-DS019)
SilverDust D2 IGF (QCI-DS021)
SilverDust D2 IGC (QCI-DS016)
Motor Interface Cable (QCI-C-D15P-D15S-nn)

This cable goes between the motor and the QuickSilver Controller/Driver (SilverNugget).
Replace the last two digits nn with length of cable in feet (i.e. 10 for 10 feet).
Shaft Seal (QCI-23M-65 or QCI-23T-65)

The shaft seal (sold separately) is required for an IP65 rating on the shaft end of the motor.
The shaft seal consists of an o-ring seal for the motors pilot and a quad ring seal for the shaft.
The shaft seal needs periodical inspections, lubrication, and replacement if worn out. The
QCI-23M-65 is for the 23 and 23H motors, while the QCI-23T-65 is for the 23T.
IP65 Motor Interface Cable (QCI-C-D15P-T14S-nn)

This cable goes between the motor and the SilverLode Controller/Driver (SilverDust D2 or
SilverNugget N2). Replace the last two digits nn with length of cable in feet (i.e. 10 for 10
feet).
SilverLode Manuals (QCI-SLM) QuickControl Software (QCI-QC)

The SilverLode User Manual, SilverLode Command Reference and QuickControl Software are
also available on our website. We recommend first time users reading chapter 1 of the User
Manual.
Power Supply (i.e. S-210-48)

A 12-48V power supply producing the amps specified above (see General Motor
Specifications) is required. QuickSilver recommends:
S-210-48 (48V, 4.4A, 210W)
Sold & Serviced By:

www.electromate.com
Part Numbers
NEMA 23 I-Grade Motors/Encoders
MOTOR TYPE/SIZE MOTOR INTERFACE
A23H-1 Blank Standard

A23L-1 DB15HD Motor Interface Connector
A23-3
A23H-3 6T IP65
A23K-3 14 Pin Round Connector
A23L-3 Shaft seal required for full IP65 rating.
A23-5 o QCI-23M-65
A23H-5 o QCI-23T-65
A23T-7 Extra coating on motor exterior.
To create a part number, choose one from each column above.
For example: 23K-3
QCI-A23K-3
This selection creates the part number: QCI-A23K-3
Standard Stocked Items
QCI-23L-1
QCI-23K-3
QCI-23L-3
QCI-23H-5
Special Orders
QCI-23H-1
QCI-23H-3
QCI-23-3
QCI-23-5
QCI-23T-7
All 6T Options
Contact Information
QuickSilver Controls, Inc.
712 Arrow Grand Circle
Covina, CA 91722
(626) 384-4760 or (888) 660-3801
(626) 384-4761 FAX
www.QuickSilverControls.com
Sold & Serviced By:

www.electromate.com

QuickSilver Controls QCI-DS008 QCI-A23

Uploaded by

Copyright:

Available Formats

QuickSilver Controls QCI-DS008 QCI-A23

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

QuickSilver Controls QCI-DS008 QCI-A23

Uploaded by

Copyright:

Available Formats

Datasheet:QCI-DS008 QuickSilver Controls, Inc.

Date: 25 June 2010 www.QuickSilverControls.com

NEMA 23 I-Grade Motor/Encoder

Shaft Seal (QCI-23M-65)

QuickSilver Controls, Inc.. ELECTROMATE

General Motor Specifications

Torque (oz-in / Nm) 30 130 55 120 30 110 43 225 220

Maximum Axial Force (lbs) 13 13 13 N/A N/A N/A N/A N/A 6

Use Use Use Use

QuickSilver Controls, Inc. Page 2 of 14 ELECTROMATE

23L-1 Torque Curve

23K-3 Torque Curve

Sold & Serviced By:

QuickSilver Controls, Inc. Page 3 of 14 ELECTROMATE

23H-5 Torque Curve

Sold & Serviced By:

QuickSilver Controls, Inc. Page 4 of 14 ELECTROMATE

23H-1 Torque Curve

23-3 Torque Curve

Sold & Serviced By:

QuickSilver Controls, Inc. Page 5 of 14 ELECTROMATE

23H-3 Torque Curve

23-5 Torque Curve

150 Torque (N-m)

Sold & Serviced By:

QuickSilver Controls, Inc. Page 6 of 14 ELECTROMATE

23T-7 Torque Curve

Sold & Serviced By:

QuickSilver Controls, Inc. Page 7 of 14 ELECTROMATE

Sold & Serviced By:

QuickSilver Controls, Inc. Page 8 of 14 ELECTROMATE

Sold & Serviced By:

QuickSilver Controls, Inc. Page 9 of 14 ELECTROMATE

1.86 47.2 mm 2.25 57.2 mm

See Length Table

Motor Series Length Shaft diameter Notes **

Sold & Serviced By:

QuickSilver Controls, Inc. Page 10 of 14 ELECTROMATE

See Length Table

Motor Series Length Shaft diameter Notes **

Sold & Serviced By:

QuickSilver Controls, Inc. Page 11 of 14 ELECTROMATE

Sold & Serviced By:

QuickSilver Controls, Inc. Page 12 of 14 ELECTROMATE

SilverNugget N2 Controller/Driver (QCI-N2-E3-04-EE) or

Motor Interface Cable (QCI-C-D15P-D15S-nn)

Shaft Seal (QCI-23M-65 or QCI-23T-65)

IP65 Motor Interface Cable (QCI-C-D15P-T14S-nn)

SilverLode Manuals (QCI-SLM) QuickControl Software (QCI-QC)

Power Supply (i.e. S-210-48)

Sold & Serviced By:

QuickSilver Controls, Inc. Page 13 of 14 ELECTROMATE

A23H-1 Blank Standard

Standard Stocked Items

Sold & Serviced By:

QuickSilver Controls, Inc. Page 14 of 14 ELECTROMATE

You might also like