Material Safety Data Sheet

Terra Industries Inc.

Terra Centre 600 Fourth Street Anhydrous Ammonia
Sioux City, Iowa 51101

MSDS Number 2001 (Revised July 1, 2003) 9 Pages

1. CHEMICAL PRODUCT and EMERGENCY TELEPHONE CONTACT

Product Name:............................................ Anhydrous Ammonia

Chemical Family: ....................................... Inorganic Nitrogen Compound
Synonyms:.................................................. Ammonia, Liquid Ammonia, Nitro-Sil, Spirit
of Hartshorn, NH3
Formula: ..................................................... NH3
Product Use:............................................... Fertilizers; Fibers and Plastics; Explosives;
Animal Feed; SCR NOx Control

EMERGENCY TELEPHONE NUMBER

CHEMTREC (U.S.): .................................. 800-424-9300
CANUTEC (Canada): ................................ 613-996-6666

2. COMPOSITION/INFORMATION ON INGREDIENTS

Ingredient Name/CAS Number Concentration Exposure Limits

Ammonia 99-100% 25 ppm TWA

#7664-41-7 35 ppm STEL
50 ppm PEL
300 ppm IDLH

3. HAZARDS IDENTIFICATION

EMERGENCY OVERVIEW
Colorless gas and liquid (liquid under pressure). Vapor is toxic and irritating to eyes,
nose, throat and skin. Liquid will burn skin and eyes and cause frostbite. Vapor is
flammable und er limited conditions. Use water to control fire and disperse vapors. Do not
put water on liquid ammonia.

POTENTIAL HEALTH EFFECTS

Primary Routes of Entry: Inhalation, skin contact/absorption and eye contact.

Page 1 of 9
General Acute Exposure: Anhydrous ammonia reacts with moisture in mucosal surfaces
(eyes, skin, and respiratory tract) to produce ammonium hydroxide, which may cause
caustic injury. The severity of injury depends upon the concentration and duration of
exposure. The extent of injury ranges from mild cough to laryngeal edema and life-
threatening pulmonary edema.

Inhalation:
Acute Exposure: Ammonia is toxic and a severe irritant of the respiratory tract. It may
cause a running nose, coughing, chest pain, cessation of respiration and death. It may cause
severe breathing difficulties, which may be delayed in onset. ADDITIONAL MEDICAL
INFORMATION: Bronchospasm, laryngitis, tracheitis, wheezing, dyspnea, and laryngeal
stridor may be noted. Mucosal burns to the tracheobronchial tree, Pulmonary Edema, and
associated hypoxemia frequently occur following exposure to concentrated ammonia.

Skin:
Acute Contact: Ammonia is a severe irritant of the skin. Skin exposure to high
concentrations of the gas may cause burning and blistering. Contact with liquid may cause
severe skin burns. ADDITIONAL MEDICAL INFORMATION: Concentrated ammonia
may produce liquefaction necrosis and deep penetrating burns.

Eye:
Acute Contact: Exposure to the eyes (>700 ppm) may cause temporary or permanent
blindness. ADDITIONAL MEDICAL INFORMATION: Eye exposure may result in
conjunctivitis, lacrimation and/or corneal irritation. Total corneal epithelial loss may occur.

Neurologic:
Acute Exposure: An altered mental status (coma) may be seen, but is not characteristic
unless hypoxemia occurs.

Gastrointestinal:
Acute Exposure: Nausea and vomiting occurs frequently following ingestion. Swelling of
the lips, mouth, and larynx, and oral or esophageal burns may occur if concentrated
ammonia solutions are ingested.

Genitourinary:
Acute Exposure: Urinary retention may occur.

Note to the Physician: Pneumonitis should be anticipated after inhalation or ingestion. If

severe exposure is suspected, observe for 48-72 hours for delayed pulmonary edema.

Carcinogenicity:

NTP:.................................................. Not Listed

IARC:................................................ Not Listed
OSHA:............................................... Not Regulated

Medical Conditions Aggravated by Exposure: Chronic respiratory or skin disease.

Page 2 of 9
4. FIRST AID MEASURES

First Aid for Eyes: Immediately flush eyes with copious amounts of tepid water for at
least 15 minutes. If irritation, pain, swelling, excessive tearing, or light sensitivity persists,
the patient should be seen in a health care facility and referral to an ophthalmologist
considered.

First Aid for Skin: Immediately flush exposed area with copious amounts of tepid water
for at least 15 minutes followed by washing area thoroughly with soap and water. The
patient should be seen in a health care facility if irritation or pain persists.

First Aid for Inhalation: Move patient to fresh air. Monitor for respiratory distress. If
cough or difficulty in breathing develops, evaluate for respiratory tract irritation,
bronchitis, or pneumonitis. If trained to do so administer supplemental oxygen with
assisted ventilation as required. Administer artificial respiration if patient is not breathing.

First Aid for Ingestion: Call a physician. If conscious, give the patient 4 to 8 ounces of
milk or water to drink immediately. Do not induce vomiting.

Caution: Clothing frozen to the skin should be thawed before being removed.

5. FIRE FIGHTING MEASURES

Flash Point:................................................. Not Applicable

Lower Flammable Limit: ........................... 15.5 % Volume in Air
Upper Flammable Limit:............................ 27.0 % Volume in Air
Autoignition Temperature.......................... 1204o F (651o C)

Extinguishing Media: Stopping the flow of gas rather than extinguishing the fire is
usually the best procedure to follow when escaping gas is burning.
Small Fire:......................................... Dry chemical or CO2
Large Fire:......................................... Water spray, fog or foam

Special Fire Fighting Procedures:

a. Do not get water inside container.
b. Move container from fire area if you can do it without risk.
c. Apply cooling water to sides of containers that are exposed to flames until well
after fire is out. Stay away from ends of tanks due to exploding potential when
tanks are involved in a fire.
d. Isolate area until gas has dispersed.
e. Use water spray or foam to control vapors.
f. Positive pressure self-contained breathing apparatus (SCBA) should be used when
there is a potential for inhalation of vapors and/or fumes.
g. Chemical protective clothing that is safe for use with ammonia involved in a fire
should be worn.

Page 3 of 9
 CAUTION:
a. With proper training, structural fire fighters protective clothing and SCBA used in
conjunction with water spray will provide limited protection for short-term
exposure to ammonia vapors.
b. Liquid ammonia may cause protective equipment to become brittle.
c. Use of welding or flame cutting equipment on or in ammonia container is not
recommended unless all ammonia has been purged, rinsed with water, and any oil
residue removed.
Runoff from fire control or dilution water may cause pollution.

6. ACCIDENTAL RELEASE MEASURES

Spill or Leak Measures: Stop leak if you can do so without risk. Keep unnecessary
people away, isolate hazard area and deny entry. Stay upwind, out of low areas, and
ventilate closed spaces before entering. Evaluate the affected area to determine whether to
evacuate or shelter- in-place by taping windows and doors, shutting off outside air intakes
(attic fans, etc.), and placing a wet towel or cloth over the face (if needed). With proper
training, self-contained breathing apparatus (SCBA) and structural firefighters protective
clothing used in conjunction with water spray will provide limited protection in outdoor
releases for short-term exposure. Fully encapsulating, vapor-protective clothing should be
worn for spills and leaks with no fire. Use water spray or foam to control vapors. Mixing
of water and liquid ammonia will increase vaporization rate. Do not put water on liquid
ammonia unless more than 100 volumes of water are available for each volume of liquid
ammonia.

CAUTION:
a. Personal protective clothing may become brittle when exposed to liquid ammonia.
b. Runoff from vapor control or dilution may cause pollution.

Determining Spill Size: Generally, a small spill is one that involves a single, small
container (55-gallon capacity or less), or a small (non-continuing) leak from a larger tank
or vessel.

Small Spill:
a. Flush area with flooding amounts of water.
b. First isolate 100 feet in all directions and then protect persons downwind 0.1 miles
during daylight and 0.1 miles at night.

Large Spill:
a. Dike far ahead of liquid spill for later disposal.
b. Follow local emergency protocol for handling.
c. First isolate 200 feet in all directions, than protect persons downwind 0.3 miles
during daylight and 0.7 miles at night.

Page 4 of 9
7. HANDLING AND STORAGE

Follow the current ANSI-K61.1 Standard, Safety Requirements for the Storage and
Handling of Anhydrous Ammonia, or applicable Ammonia Manufacturing Industry
Standards.

Handling Precautions: Use proper personal protective equipment when working with or
around ammonia. See Section 8.

8. EXPOSURE CONTROLS, PERSONAL PROTECTION

Respiratory Protection Requirements:

<25 ppm: No protection required.

25 to 35 ppm: Protection required if the daily TWA is exceeded.

35 to 50 ppm: Protection required if exposed for more than 15 minutes.

50 to 250 ppm: Minimum of an air-purifying respirator equipped with

ammonia canister(s) or cartridge(s).

250 to 300 ppm: Minimum of a full- face air-purifying respirator equipped

with ammonia canister(s) or cartridge(s).

>300 ppm: A fresh air supply system must be used (i.e. positive
pressure self contained breathing apparatus).

Skin Protection Requirements: Skin protection is required for exposure to liquid, mist,
and > 1000 ppm of ammonia gas or vapors. Neoprene or rubber gauntlet-type gloves,
ammonia resistant clothing (overalls, jacket, and boots) or vapor suit, as required.

Eye Protection Requirements: Use chemical (indirectly vented) goggles when there is a
potential for contact with liquid or mist. A full- face shield is recommended in addition to
goggles for added protection.

Other Protective Equipment: Safety shower and eyewash fountain should be provided
in the ammonia handling area. In agricultural distribution, provide easily accessible shower
and/or at least 100 gallons of clean water in open top container (check regulations). When
transporting, provide at least 5 gallons of readily accessible, clean water and personal
protective equipment.

Engineering Controls: Maintain adequate ventilation to keep ammonia concentrations

below applicable standards when possible.

NOTE: See Section 2 for regulatory exposure limits.

Page 5 of 9
9. PHYSICAL AND CHEMICAL PROPERTIES

Physical Form:............................................... Gas (liquid under pressure)

Color:............................................................. Colorless gas and liquid, forms white vapor in
contact with moisture
Odor:.............................................................. Strong pungent penetrating odor, ammonia.
Boiling Point: ................................................ -28.1o F (-33o C) at 1 atm
Melting point:................................................ -107.9o F (-78o C)
Ph:.................................................................. Approximately 12.0 (neat)
Solubility: ...................................................... 510 - 530 g/L @ 20o C
Specific Gravity: ........................................... 0.6818 @ -33.35o C and 1 atm
Vapor Density: .............................................. 0.597 @ 0o C (0.60 @ 60o F)
Vapor Pressure: ............................................. 7,600 mm Hg @ 25o C (93 psig @ 60o F)
% Volatile by Volume:.................................. 100
Molecular Weight:......................................... 17.03
Density: ......................................................... 0.696 g/L @ 20o C (5.14 lb./gal. @ 60o F)
Critical Temperature: .................................... 271o F (133o C)
Critical Pressure: ........................................... 1636 psia

10. REACTIVITY

Stability: ........................................................ This is a stable material.

Hazardous Polymerization: ........................... Will not occur.

Decomposition: Hydrogen is released on heating above 850o F (454o C). The

decomposition temperature may be lowered to 575o F (300o C) by contact with certain
metals such as nickel. At 12900 F (690o C) or in the presence of an electric spark, ammonia
decomposes into nitrogen and hydrogen gases, which may form a flammable mixture in
the air.

Incompatibilities:
a. Ammonia has potentially explosive or violent reactions with interhalogens, strong
oxidizers, Nitric Acid, Fluorine, and Nitrogen Oxide.

b. Ammonia forms sensitive explosive mixtures with air and hydrocarbons, Ethanol
and Silver Nitrate, and Chlorine; and explosive products are formed by the reaction
of ammonia with Silver Chloride, Silver Oxide, Bromine, Iodine, Gold, Mercury,
and Tellurium Halides.

c. Ammonia is incompatible or has potentially hazardous reactions with Silver,

Acetaldehyde, Acrolein, Boron, Halogens, Perchlorate, Chloric Acid, Chlorine
Monoxide, Chlorites, Nitrogen Tetroxide, Tin, and Sulfur.

NOTE: The incompatibilities above are a partial list taken from two books by Sax &
Lewis: Dangerous Properties of Industrial Materials, 7th. ed., 1989 and Hawleys
Condensed Chemical Dictionary, 11th. ed. 1987, both published by Van Nostrand
Reinhold Company, New York. It is recommend that if additional information is required,
the reader refer to these and other published information.

Page 6 of 9
11. TOXICOLOGICAL INFORMATION

Toxicity

Acute Inhalation Toxicity

LC50 Rat, mouse:..................................... 4,200 - 19,060 mg NH3 /m3 (1 hr)
Acute Toxicity, Other Routes
LC50 Rat, mouse:..................................... 45.5 - 195.1 mg NH3 /kg bw (I hr intravenous)
Corrosiveness / Irritation
Skin Irritation / Corrosion: ............................ Corrosive to skin
Eye Irritation / Corrosion: ............................. Subacute and chronic exposure to 200 1,000
ppm produced eye damage. 100 200 ppm
produced moderate to severe irritation.
Repeated Dose Toxicity
Rats, guinea pigs, rabbits, etc:No mortality (Inhalation up to 770 mg/m3 )
Genetic Toxicity in vitro
Salmonella typhimurium, etc:.Negative (Bacterial gene mutation assay)
Chick fibroblasts:Induced chromosomal clumping, polyploidy, and
arrested spindle formation. No date showing that
ammonia is mutagenic in mammals. (Cytogenetic
assay)
Genetic Toxicity in vivo
Drosophila melanogaster:..No evidence for mutagenicity
Carcinogenicity
All:..No carcinogenic effects
Toxicity to Reproduction
Pig:..Temporarily depressed mean daily gain (MDG) at
35 mg/kg in gilts (One generation study)
Human Experience
Inhalation, human volunteers:Nasal and pulmonary irritation at concentrations of
about 100 ppm and higher.

Ecotoxicity

Acute Toxicity to Fish

LC50 Many species:................................. 0.09 3.51 mg un- ionized NH3 /L (96 hr)
Acute Toxicity to Aquatic Invertebrates
LC50 Daphnia magna:............................. 2.94 mg un- ionized NH3 -N/L (48 hr)
Toxicity to Aquatic Plants
LOEC Benthic diatoms:............................. 0.5 1.0 mg N/L (Up to 25 days)
LOEC Chlorella vulgaris: ......................... 500 mg N/L (21 days)
Toxicity to Bacteria
EC50 Photobacterium phosphoreum:...... 1.49 mg un- ionized NH3 /L (5 min)

Page 7 of 9
 Chronic Toxicity to Fish
NOEC Many species: .................................0.025 1.2 mg un- ionized NH3 /L (Varied 12
days 5 years)
Chronic Toxicity to Aquatic Invertebrates
NOEC Daphnia magna and others:............0.163 0.42 mg un- ionized NH3 /L (Varied
21 days 76 weeks)
Toxicity to Terrestrial Plants
LOEC Many species ..................................3 250 ppm (Varied 4 min 16 hrs)
Toxicity to Other Non-Mammalian Terrestrial Species
LD50 G. Domesticus:2.72 mM (1 hr injections)

Source: TFI Product Testing Program April 2003

12. ECOLOGICAL INFORMATION

a. Ammonia is harmful to aquatic life in very low concentrations and may be
hazardous if it enters water intakes.
b. Local health and wildlife authorities, as well as operators of water intakes in the
vicinity, should be notified of water releases.
c. Waterfowl toxicity may occur at elevated concentrations.
d. Ammonia does not concentrate in the food chain.
e. The conversion of ammonia to nitrites/nitrates by bacteria in aquatic systems can
reduce the concentration of dissolved oxygen (referred to as nitrogenous oxygen
demand).
Effect on water treatment process: Chlorination will produce chloramines, which are more readily
detected by taste and odor.

Note: See Ecotoxicity information in section 11.

13. DISPOSAL CONSIDERATIONS

Reclaim as fertilizer if possible. Waste must be disposed of in accordance with federal,

state, and local environmental control regulations.

14. TRANSPORTATION INFORMATION

U.S. DOT and Canadian TGD Act

Shipping Name:............................................. Ammonia, anhydrous
Shipping Class/Division:............................... 2.2 (8)
Hazard Class:................................................. Non-Flammable Gas (Corrosive)
Product Identification Number (PIN):........... UN1005
DOT Placard:................................................. Non-Flammable Gas 2.2, color: green
DOT Special Provision: ................................ 13, Inhalation Hazard
OSHA Label Required:................................. Yes
RQ (Reportable Quantity):............................ 100 pounds
STCC Number:.............................................. 4904210

Page 8 of 9
15. REGULATORY INFORMATION
Controlled Products Regulations Classification: A: Compressed Gas; E: Corrosive

OSHA: This product is considered a hazardous material under criteria of the Federal
OSHA Hazard Communication Standard 29 CFR 1910.1200 (Toxic; Corrosive), and is
listed as a Highly Hazardous Chemical subject to the requirements of the Process Safety
Management Standard 29 CFR 1910.119.

CAA Chemical Accident Prevention: Ammonia is considered a regulated substance

subject to the Chemical Accident Prevention provisions of 40 CFR Part 68. The threshold
quantity for this substance is 10,000 lbs.
SARA TITLE III:
a. EHS (Extremely Hazardous Substances) List: Listed (EPA, 1992a)
b. SARA RQ (Reportable Quantity): 100 pounds
c. TPQ (Threshold Planning Quantity): 500 pounds
d. Regulation: Emergency Planning and Notification - 40 CFR Part 355
(Appendices A and B).
e. Section 313: Specific Toxic Chemical Listings - 40 CFR Part 372
Ammonia is subject to the reporting requirements of Section 313 Specific Toxic
Chemical Listings 40 CFR Part 372. Terra is required by 40 CFR 372.45 to notify
certain customers as to which of its mixture or trade name products contain those
chemicals. The purpose of that notification is to ensure that facilities that may be
subject to the reporting requirements of Section 313 and that use products of
unknown formulation will have knowledge that they are receiving products that
contain chemicals subject to those reporting requirements.

CERCLA Hazardous Substances List:

a. CERCLA RQ (Reportable Quantity): 100 pounds
b. Regulation: Designation, Reportable Quantities, Notification - 40 CFR 302

TSCA Inventory: Listed (RTECS)

16. OTHER INFORMATION

Dec. 18, 1995: The MSDS was rewritten to comply with ANSI Standard Z400.1-1993.
July 1, 2003: Added toxicity information from the TFI Product Testing Program April 2003.

The information and recommendations herein are taken from data contained in independent,
industry-recognized references including but not limited to NIOSH, OSHA, ANSI, NFPA, DOT
ERG, the TFI Product Testing Program, Global Engineering Documents, MEDITEXT,
HAZARDTEXT, SARATEXT, CHRIS, OHM/TADS, and IRIS. Terra Industries Inc. makes no
guarantee, warranty or other representation concerning this substance, since conditions of its us are
beyond the control of the company. Terra Industries Inc. disclaims any liability for loss or damage
incurred in connection with the use of this substance.

Page 9 of 9