Diesel Power, Expanded Capabilities: Ranger 305 D
Diesel Power, Expanded Capabilities: Ranger 305 D
Diesel Power, Expanded Capabilities: Ranger 305 D
EXPANDED CAPABILITIES
Ranger 305 D
Shown:
Ranger 305 D, K1727-3
300 0
250 2,300
200 4,200
150 5,600
100 7,100
0 9,500
FEATURES
Simple Controls - Keep training time to a minimum with the Compatible with many Lincoln wire feeders including the
straightforward control panel of the Ranger 305 D. The flip-down LN-25 Ironworker, LN-15, LF-72, LF-74, LN-7 GMA, LN-742, LN-8 wire
control panel door keeps less frequently used controls out of the way. feeders and Magnum SG Spool Gun.
Single, full-range output control dial. No confusion with taps and Wire feed voltmeter switch matches polarity of wire feeder volt
controls! meter to polarity of electrode.
4 welding modes: CC-Stick, Downhill Pipe, CV-Wire, and Top-of-the-line water-cooled Kubota 18.8 HP D722
DC Touch Start TIG. diesel engine with electric start. EPA Tier 4 Final.
Dual digital output meters for presetting weld amps for stick, TIG or Fully enclosed case for equipment protection and low noise. Noise at
downhill pipe modes, or voltage for CV wire mode. Also displays actual rated load:
outputs while welding. Memory feature holds output readings for 7 104.2 dB sound power (Lwa)
seconds after welding stops for viewing by the operator. 80.6 dBA sound level at 23 ft. (7 m)
Output at welding terminals controlled by electronic contactor. Glow plugs for rapid starting down to 5F (-15C).
Can be switched to On, or to Remotely Controlled. Mechanical fuel pump is activated when glow plug button is pressed.
Remote is auto-activated when plugged into a 6-pin connector.
For the CC-stick, downhill pipe and Touch Start TIG modes, the
machine output dial becomes a maximum current limit for more fine
tuning with the remote control dial or Amptrol.
[ 3 ] | Ranger 305 D
FEATURES, CONTD.
Engine closed breather system keeps engine compartment clean! Large top fuel filler neck is easily
Eliminates oil mist from collecting inside engine compartment, accessed for refueling.
especially on radiator surfaces, which would lower engine cooling
efficiency. Also prevents oil drips to a truck bed or the ground
from an open breather discharge.
12 gallon fuel capacity allows you to run an extended day.
Electric fuel gauge located on control panel makes it easy to
check the fuel level during operation. Helps you eliminate
running low on fuel during critical jobs. Oil drain valve (no tools required) with removable extension tube.
Convenient truck or trailer mounting with front and rear holes
in base.
KEY CONTROLS
1. Hour Meter
20 19 18 17 16 2. Output Control Dia
3. Digital Weld Output Ammeter
4. Weld Mode Switch
1 5. Arc Force & Inductance/ Pinch Control
15
6. Circuit Breakers
2
7. 120 Volt AC GFCI Receptacles (NEMA 5-20R)
3 14 8. Output Stud Covers
13 9. Ground Stud
10. 120/240 Volt AC Full KVA Receptacle (NEMA 14-50R)
4 12
11. Remote Control & Feeder Connectors
5 12. Wire Feeder Voltmeter Polarity Switch
13. Output Contactor ControlSwitch
6 11
14. Digital Weld Output Voltmeter
10
7 15. Idler Control Switch
9 16. Engine Protection Light
17. Pushbutton Start Switch
8 18. Glow Plug Button
19. Run/Stop Switch
20. Electric Fuel Gauge
Ranger 305 D | [ 4 ]
QUALITY AND RELIABILITY
Printed circuit boards are environmentally-shielded using Lincoln Automatic engine shutdown protection for low oil pressure or high
Electric engineered potting and protective frame trays. engine temperature. Indicator light on control panel.
Oil dip stick, filters, spark plugs, etc. are easily accessed with left, Dependability and long life aided by all-copper windings in rotor and
right and top engine doors. Left and right doors are removable. stator with high quality insulation.
Adjust exhaust direction with top-mounted 360 rotatable exhaust Canadian Standards Association (CSA) certified.
muffler. Muffler made from aluminized steel for long life. Manufactured under a quality system certified to ISO 9001
Attractive red and black powder paint finish offers increased requirements and ISO 14001 environmental standards.
durability with added protection from rust and corrosion. Three-year Lincoln Electric warranty (engine is warranted separately
Longer engine life, reduced noise emissions and greater fuel by the manufacturer - see Engine Specifications, footnote 6).
economy with automatic engine idler.
Conveniently located engine maintenance label under top
engine door.
Engine hour meter for scheduled maintenance. Printed circuit boards are
environmentally-shielded using
Circuit breaker protection on the battery ignition system Lincoln Electrics engineered potting
provides added component protection. and protective frame trays.
Reliable start-up with Group 58 battery with 550 cold
cranking amps.
MACHINESPECIFICATIONS
CC/Pipe Rated Output (1) CV-Rated Output Dimensions
Product Ordering Current/Voltage/ Current/Voltage/ Generator HxWxL Weight
Name Information Description Duty Cycle Duty Cycle AC Power (3)(4) inches (mm) lbs. (kg)
Ranger 305 D K1727-4 300 Amp DC Multi-Process DC Constant Current DC Constant Voltage (2) 10,000 Watts Peak 29.9 x 21.5 x 52.3 in 698
(Kubota) Arc Welder with 305A/29V/100% 300A/29V/100% 9,500 Watts Continuous (759 x 546 x 1327 mm) (317)
Lincoln Electric 20-305A 60 Hz
Chopper Technology 14-29 V Single Phase To top of exhaust tube:
DC Pipe Current Single-Dial 35.8 in. (909 mm)
10,000 Watts Peak 300A/29V/100% Continuous Control Full KVA
40-300A Receptacle
9,500 Watts Wire Feeder Power 40A@ 240V
Continuous AC Power Touch Start TIG 42V, 60 Hz, 15 Amps 40A@ 120V ea.
250A/30V/100% 120V, 60 Hz, 20 Amps Branch Circuit (5)
20-250 A
Four 120V GFCI
Single Dial Receptacles
Continuous Control 20A per Duplex
60V DC Max OCV @ 40A Total (5)
3650 RPM
(1) High Altitude: For maximum rating, derate the output 2.5% to 3.5% for every 1,000 ft. (300 m). High Temperature: For maximum rating, derate 2 volts for every 18F (10C)
above 104F (40C). See Operator Manual for additional information.
(2) DC constant voltage capability provides convenience and added safety when welding in electrically hazardous conditions.
(3) When welding, available auxiliary power will be reduced. Output voltage is within +\- 10% at all loads up to rated capacity.
(4) 120V will operate either 60 Hz or 50/60 Hz power tools, lights, etc.
Kubota warranty is 2 years/2,000 hours for machines shipped within the U.S., Canada, Pacific Ocean region and Western Europe.
(6)
Warranty is 1 year/1,000 hours for Asia, Africa and Middle East.
SYSTEM SELECTION
K2614-9 LN-25 Ironworker K126-12 Gun and Cable 5/64 in. (2.0 mm) NR-233
Wire Feeder 25 lb. (11.3 kg) Spool
[ 6 ] | Ranger 305 D
RECOMMENDED ACCESSORIES
Ranger 305 D | [ 7 ]
RECOMMENDED ACCESSORIES
PRODUCT SPECIFICATIONS
Product Product Rated Output Output Number HP & Speed H x W x D Net Weight
Name Number Current/Voltage/Duty Cycle Range Engine of Cylinders (rpm) inches (mm) lbs.(kg)
Ranger 305 D K1727-4 305A DC CC/29V/100% 20-305A DC Kubota D722 Diesel 3 18.8 @ 3600 29.9 x 21.5 x 52.3 698
300A DC CV/29V/100% 40-300A Pipe EPA Tier 4 (759 x 546 x 1327) (317)
20-250A DC TIG To top of exhaust tube:
14-29V CV 35.8 (909)
10,000 Watts Peak
9,500 Watts Continuous
Ranger 305 D K2352-5
One-Pak
For best welding results with Lincoln Electric equipment, always use Lincoln Electric consumables. Visit www.lincolnelectric.com for more details.
Manufactured at a facility with certified ISO Quality and Environmental Management Systems.
Lincoln Electric is a responsive manufacturer, but the selection and use of specific products sold by Lincoln Electric is solely within the control of, and remains the sole responsibility of the customer. Many variables beyond the control of Lincoln
Electric affect the results obtained in applying these types of fabrication methods and service requirements.
Subject to Change This information is accurate to the best of our knowledge at the time of printing. Please refer to www.lincolnelectric.com for any updated information.