SLM2xx Manual Switch

USER GUIDE
BUSINESS SERIES
Business Series Smart

Gigabit Ethernet Switch
Model: SLM2048 (EU), SLM2024 (EU), SLM248G (EU), SLM248P (EU),
SLM224G (EU), SLM224P (EU)
About This Guide
About This Guide

Icon Descriptions
While reading through the User Guide you may encounter
various icons designed to call attention to a specific item.
Below is a description of these icons:
NOTE: This check mark indicates that there is

a note of interest and is something that you
should pay special attention to while using the
product.
WARNING: This exclamation point indicates

that there is a caution or warning and it is
something that could damage your property or
product.
WEB: This globe icon indicates a noteworthy

website address or e-mail address.
Online Resources
Website addresses in this document are listed without
http:// in front of the address because most current web
browsers do not require it. If you use an older web browser,
you may have to add http:// in front of the web address.
Resource Website
Linksys Europe www.linksys.eu
Linksys International www.linksys.com/international
Linksys www.linksys.com
Glossary www.linksys.com/glossary
Network Security www.linksys.com/security
Copyright and Trademarks

Specifications are subject to change without notice.
Linksys is a registered trademark or trademark of Cisco
Systems, Inc. and/or its affiliates in the U.S. and certain
other countries. Copyright © 2007 Cisco Systems, Inc. All
rights reserved. Other brands and product names are
trademarks or registered trademarks of their respective
holders.
a
Business Series Smart Gigabit Ethernet Switch
Table of Contents
Chapter 1: Introduction 1
Chapter 2: Product Overview 2
SLM2048 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Back Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
SLM2024 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Back Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
SLM248G . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Back Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
SLM248P . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Back Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
SLM224G . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Back Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
SLM224P . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Back Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Chapter 3: Installation 8
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Pre-Installation Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Fast Ethernet Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Full-Duplex Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
1000BASE-T Cable Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Positioning the Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Placement Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Desktop Placement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Rack-Mount Placement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Hardware Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Uplinking the Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Chapter 4: Configuration Using the Web-based Utility 11

Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Setup > Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Setup > Network Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Setup > Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Port Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Port Management > Port Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Port Management > Link Aggregation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Business Series Smart Gigabit Ethernet Switch ii

Table of Contents
Port Management > LACP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Port Management > PoE Power Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
VLAN Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
VLAN Management > Create VLAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
VLAN Management > Port Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
VLAN Management > Port to VLAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
VLAN Management > VLAN to Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Statistics > Interface Statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Security > 802.1x Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Security > Port Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Security > Storm Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Security > RADIUS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
QoS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
QoS > CoS Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
QoS > Queue Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
QoS > DSCP Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
QoS > Basic Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Spanning Tree . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Spanning Tree > STP Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Spanning Tree > Global STP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Spanning Tree > STP Port Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Multicast . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Multicast > IGMP Snooping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Multicast > Bridge Multicast . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Multicast > Bridge Multicast Forward All . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Admin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Admin > User Authentication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Admin > Static Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Admin > Dynamic Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Admin > Port Mirroring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Admin > Save Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Admin > Firmware Upgrade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Admin > Reboot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Admin > Factory Default . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Admin > Logging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Admin > Memory Logs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Admin > Flash Logs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Logout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Appendix A: About Gigabit Ethernet and Fiber Optic Cabling 37

Gigabit Ethernet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Business Series Smart Gigabit Ethernet Switch iii

Table of Contents
Fiber Optic Cabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Appendix B: Glossary 38
Appendix C: Specifications 42
SLM2024/SLM2048 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
SLM224G/SLM248G/SLM224P/SLM248P . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Appendix D: Warranty Information 45

Appendix E: Regulatory Information 46
FCC Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Safety Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Industry Canada Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Avis d’ Industrie Canada . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
EC Declaration of Conformity (Europe) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
User Information for Consumer Products Covered by EU Directive 2002/96/EC on Waste
Electric and Electronic Equipment (WEEE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Appendix F: Contact Information 51

Europe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Outside of Europe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Business Series Smart Gigabit Ethernet Switch iv

Chapter 1 Introduction
Chapter 1: security by keeping sensitive data separated from other

workgroups on the network..
Introduction Network Security is an absolute requirement for any
business and preventing unauthorized access to the
Thank you for choosing the Linksys Business Series Smart company network is business-critical. The Smart Switch
Gigabit Ethernet Switch. secures the network through 802.1X port authentication
which prompts end-users to provide their username
The new Linksys Business Series Smart Gigabit Ethernet and password before they are permitted to pass data.
Switches are cost-effective switching solutions ideal User access can also be controlled through the Smart
for small businesses, the network edge, or workgroups Switch’s MAC-Based Filtering capability which allows
within larger organizations. These easy-to-install, high- network access only to those devices or workstations that
speed switches offer many of the same Quality of Service have been authorized as identified by their MAC (Media
and Security features found in more expensive full Layer Access Control) address. The Many-to-One or One-to-One
2 managed switches but without their complexity. The Port Mirroring feature of the Smart Switch enables you
Smart Switches offer the following interfaces: to monitor the type of traffic being transmitted on the
• The SLM2024 and SLM2048 offer twenty four (24) or network.
forty eight (48) 10/100/1000 Gigabit copper ports, with The Smart Switch includes features for quickly expanding
two (2) shared copper or optical (SFP) uplink interfaces and growing your network. To substantially increase
for connecting the switch to the core network. network throughput speeds, especially useful for
• The SLM224G, SLM224P, SLM248G, and SLM248P companies whose employees are routinely backing up
offer twenty four (24) or forty eight (48) 10/100 copper their hard drives to a company server or storage platform,
ports, with two (2) shared Gigabit copper or optical the Smart Switch supports Link Aggregation which allows
(SFP) uplink interfaces for connecting the switch to the multiple high-bandwidth trunks between switches to be
core network. set up. Link Aggregation also provides a level of availability
and redundancy as traffic will continue to flow even if one
The Smart Switch’s simplified user interface is an intuitive
of the network links breaks. The Smart Switch’s Spanning
management tool enabling you to quickly utilize the
Tree Protocol support (STP) and Storm Control features
comprehensive feature-set of the switch, resulting in a
help to control planned or inadvertent cable loops when
better optimized network.
switches are connected to one another. These loops can
For Wireless or VoIP deployments, the SLM224P and cause broadcast or multicast storms in the network and
SLM248P support the IEEE802.3af standard for Power over severely limit its performance. With these features, you can
Ethernet (PoE). This eliminates the need for additional confidently build a mesh of switches and quickly expand
power cables and the need for a nearby power outlet, your network to support your growing workforce.
thereby making installation simple and inexpensive,
allowing networking devices like cameras and Wireless
Access Points to be positioned in optimal locations like in
ceilings and walls -- even outdoors.
The Smart Switch includes numerous QoS features to
ensure that traffic is prioritized properly to deliver the
best possible user experience for real time applications
like voice and video or bandwidth intensive graphic/
video file uploads or downloads. With its IGMP Snooping
feature, the Smart Switch limits IP multicast traffic (real
time presentations, videoconferences, on-line gaming)
to only the ports that have requested it enabling the rest
of the network to operate at peak efficiency. Additional
QoS capabilities like IEEE 802.1p Priority Tagging, DSCP
(Differentiated Services Code Point), and 4 hardware
queues also maintain quality for real-time applications like
voice and video. Network traffic can be optimized with the
switch’s 802.1Q VLAN (Virtual LAN) support which enables
you to quickly segregate network traffic by department
or workgroup. VLANs also provide an additional layer of

Chapter 2 Product Overview
Chapter 2: miniGBIC (1-2) The miniGBIC (gigabit interface

converter) port is a connection point for a
Product Overview miniGBIC expansion module, so the Switch can
be uplinked via fiber to another switch. The
MiniGBIC port provides a link to a high-speed
SLM2048 network segment or individual workstation at
speeds of up to 1000 Mbps.
Front Panel To establish a Gigabit Ethernet connection using
The Switch’s LEDs and ports are located on the front a miniGBIC port, you will need to install a MGBT1,
panel. MGBSX1, or MGBLH1 Gigabit expansion module
and use Category 5e cabling or fiber optic
cabling.
To establish a Fast Ethernet connection using a
Front Panel of the SLM2048 miniGBIC port, you will need to install a MFEFX1
(100BASE-FX) or MFELX1 (100BASE-LX) 100SFP
Transceiver and use fiber optic cabling.
SYSTEM (Green) Lights up to indicate that the
Switch is powered on. Blinks while the Switch is
performing a system self-test. NOTE: On the SLM2048, MiniGBIC ports are
shared with standard ports. If a miniGBIC port is
LNK/ACT (1-48) (Green) Lights up to indicate
used, then the shared standard port on the Switch
a functional 10/100/1000 Mbps network link
cannot be used. The following table defines the
through the corresponding port (1 through 48)
shared port mapping of the SLM2048 Switch.
with an attached device. Blinks to indicate that
the Switch is actively sending or receiving data
over that port.
Gigabit (1-48) (Amber) Lights up to indicate SLM2048 Shared Port Mapping
a functional 1000 Mbps connection on the miniGBIC Port Standard Port
corresponding port (1 through 48) with an
attached device. miniGBIC 1 Port 24
Reset Press and hold the Reset Button for less
than ten seconds to reboot the Switch. Press and miniGBIC 2 Port 48
hold the Reset Button for more than ten seconds
to reset the Switch’s settings to the factory
defaults. Back Panel
Ethernet 1-48 The Switch is equipped with 48 The power port is located on the back panel of the
auto-sensing, Ethernet network ports, which Switch.
use RJ-45 connectors. The Fast Ethernet ports
support network speeds of 10 Mbps, 100 Mbps,
or 1000 Mbps. They can operate in half- and full-
duplex modes. Auto-sensing technology enables
Back Panel of the SLM2048
each port to automatically detect the speed of
the device connected to it (10 Mbps, 100 Mbps,
or 1000 Mbps), and adjust its speed and duplex POWER The Power port is where you connect
accordingly. the AC power.

SLM2024 miniGBIC (1-2) The miniGBIC (gigabit interface

Front Panel miniGBIC expansion module, so the Switch can
be uplinked via fiber to another switch. The
The Switch’s LEDs and ports are located on the front MiniGBIC port provides a link to a high-speed
panel. network segment or individual workstation at
speeds of up to 1000 Mbps.
To establish a Gigabit Ethernet connection using
a miniGBIC port, you will need to install a MGBT1,
Front Panel of the SLM2024
MGBSX1, or MGBLH1 Gigabit expansion module
and use Category 5e cabling or fiber optic
SYSTEM (Green) Lights up to indicate that the cabling.
Switch is powered on. Blinks while the Switch is To establish a Fast Ethernet connection using a
performing a system self-test. miniGBIC port, you will need to install a MFEFX1
LNK/ACT (1-24) (Green) Lights up to indicate (100BASE-FX) or MFELX1 (100BASE-LX) 100SFP
a functional 10/100/1000 Mbps network link Transceiver and use fiber optic cabling.
through the corresponding port (1 through 24)
the Switch is actively sending or receiving data NOTE: On the SLM2024, MiniGBIC ports are
over that port. shared with standard ports. If a miniGBIC port is
used, then the shared standard port on the Switch
Gigabit (1-24) (Amber) Lights up to indicate cannot be used. The following table defines the
a functional 1000 Mbps connection on the shared port mapping of the SLM2024 Switch.
corresponding port (1 through 24) with an
attached device.
SLM2024 Shared Port Mapping
than ten seconds to reboot the Switch. Press and
hold the Reset Button for more than ten seconds miniGBIC Port Standard Port
defaults. miniGBIC 1 Port 12
Ethernet 1-24 The Switch is equipped with 24
miniGBIC 2 Port 24
auto-sensing, Ethernet network ports, which
support network speeds of 10 Mbps, 100 Mbps,
or 1000 Mbps. They can operate in half- and full-
Back Panel
duplex modes. Auto-sensing technology enables The power port is located on the back panel of the
each port to automatically detect the speed of Switch.
the device connected to it (10 Mbps, 100 Mbps,
or 1000 Mbps), and adjust its speed and duplex
accordingly.
Back Panel of the SLM2024
POWER The Power port is where you connect

the AC power.

SLM248G G1-G2 The Switch is equipped with 2 auto-

sensing Gigabit Ethernet network ports, which
Front Panel use RJ-45 connectors. The Gigabit Ethernet ports
support network speeds of 10 Mbps, 100 Mbps, or
The Switch’s LEDs and ports are located on the front 1000 Mbps. They can operate in half- and full-duplex
panel. modes. Auto-sensing technology enables each port
to automatically detect the speed of the device
connected to it (10 Mbps, 100 Mbps, or 1000 Mbps),
and adjust its speed and duplex accordingly.
Front Panel of the SLM248G miniGBIC (1-2) The miniGBIC (gigabit interface
SYSTEM (Green) Lights up to indicate that the miniGBIC expansion module, so the Switch can
Switch is powered on. Blinks while the Switch is be uplinked via fiber to another switch. The
performing a system self-test. MiniGBIC port provides a link to a high-speed
network segment or individual workstation at
LNK/ACT (1-48) (Green) Lights up to indicate speeds of up to 1000 Mbps.
a functional 10/100 Mbps network link through
the corresponding port (1 through 48) with To establish a Gigabit Ethernet connection using
an attached device. Blinks to indicate that the a miniGBIC port, you will need to install a MGBT1,
Switch is actively sending or receiving data over MGBSX1, or MGBLH1 Gigabit expansion module
that port. and use Category 5e cabling or fiber optic cabling.
100M (1-48) (Amber) Lights up to indicate To establish a Fast Ethernet connection using a
a functional 100 Mbps connection on the miniGBIC port, you will need to install a MFEFX1
corresponding port (1 through 48) with an (100BASE-FX) or MFELX1 (100BASE-LX) 100SFP
attached device. Transceiver and use fiber optic cabling.
LNK/ACT (G1-G2) (Green) Lights up to indicate
a functional 10/100/1000 Mbps network link NOTE: On the SLM248G, MiniGBIC ports are
through the corresponding port (G1 through G2) shared with Gigabit Ethernet ports. If a miniGBIC
with an attached device. Blinks to indicate that port is used, then the shared Gigabit Ethernet
the Switch is actively sending or receiving data port on the Switch cannot be used. The following
over that port. table defines the shared port mapping of the
Gigabit (G1-G2) (Amber) Lights up to indicate SLM248G Switch.
a functional 1000 Mbps connection on the
corresponding port (G1 through G2) with an
attached device.
SLM248G Shared Port Mapping
than ten seconds to reboot the Switch. Press and miniGBIC Port Gigabit Port
miniGBIC 1 Port G1
defaults.
miniGBIC 2 Port G2
use RJ-45 connectors. The Fast Ethernet ports Back Panel
support network speeds of 10 Mbps or 100 Mbps.
They can operate in half- and full-duplex modes. The power port is located on the back panel of the Switch.
Auto-sensing technology enables each port to
automatically detect the speed of the device
connected to it (10 Mbps or 100 Mbps), and
adjust its speed and duplex accordingly. Back Panel of the SLM248G

the AC power.

SLM248P G1-G2 The Switch is equipped with 2 auto-

Front Panel of the SLM248P miniGBIC (1-2) The miniGBIC (gigabit interface
PoE (1-12, 25-36) (Amber) Blinks to indicate that To establish a Fast Ethernet connection using a
power is being supplied to an attached powered miniGBIC port, you will need to install a MFEFX1
device on the corresponding port (1 through 12, (100BASE-FX) or MFELX1 (100BASE-LX) 100SFP
25 through 36). Transceiver and use fiber optic cabling.
100M (13-24, 37-48) (Amber) Lights up to
indicate a functional 100 Mbps connection NOTE: On the SLM248P, MiniGBIC ports are
on the corresponding port (13 through 24, 37 shared with Gigabit Ethernet ports. If a miniGBIC
through 48) with an attached device. port is used, then the shared Gigabit Ethernet
LNK/ACT (G1-G2) (Green) Lights up to indicate port on the Switch cannot be used. The following
a functional 10/100/1000 Mbps network link table defines the shared port mapping of the
through the corresponding port (G1 through G2) SLM248P Switch.
over that port.
SLM248P Shared Port Mapping
Gigabit (G1-G2) (Amber) Lights up to indicate
a functional 1000 Mbps connection on the miniGBIC Port Gigabit Port
miniGBIC 1 Port G1
attached device.
Reset Press and hold the Reset Button for less miniGBIC 2 Port G2
than ten seconds to reboot the Switch. Press and
to reset the Switch’s settings to the factory Back Panel
defaults.
Ethernet 1-48 The Switch is equipped with 48 The power port is located on the back panel of the Switch.
They can operate in half- and full-duplex modes. Back Panel of the SLM248P
automatically detect the speed of the device POWER The Power port is where you connect
connected to it (10 Mbps or 100 Mbps), and the AC power.
adjust its speed and duplex accordingly.

SLM224G G1-G2 The Switch is equipped with 2 auto-

Front Panel of the SLM224G miniGBIC (1-2) The miniGBIC (gigabit interface
100M (1-24) (Amber) Lights up to indicate To establish a Fast Ethernet connection using a
a functional 100 Mbps connection on the miniGBIC port, you will need to install a MFEFX1
corresponding port (1 through 24) with an (100BASE-FX) or MFELX1 (100BASE-LX) 100SFP
attached device. Transceiver and use fiber optic cabling.
LNK/ACT (G1-G2) (Green) Lights up to indicate
a functional 10/100/1000 Mbps network link NOTE: On the SLM224G, MiniGBIC ports are
through the corresponding port (G1 through G2) shared with Gigabit Ethernet ports. If a miniGBIC
with an attached device. Blinks to indicate that port is used, then the shared Gigabit Ethernet
the Switch is actively sending or receiving data port on the Switch cannot be used. The following
over that port. table defines the shared port mapping of the
Gigabit (G1-G2) (Amber) Lights up to indicate SLM224G Switch.
a functional 1000 Mbps connection on the
attached device.
SLM224G Shared Port Mapping
than ten seconds to reboot the Switch. Press and miniGBIC Port Gigabit Port
miniGBIC 1 Port G1
defaults.
miniGBIC 2 Port G2
use RJ-45 connectors. The Fast Ethernet ports Back Panel
They can operate in half- and full-duplex modes. The power port is located on the back panel of the Switch.
automatically detect the speed of the device
connected to it (10 Mbps or 100 Mbps), and
adjust its speed and duplex accordingly. Back Panel of the SLM224G

the AC power.

SLM224P G1-G2 The Switch is equipped with 2 auto-

Front Panel of the SLM224P miniGBIC (1-2) The miniGBIC (gigabit interface
PoE (1-6, 13-18) (Amber) Blinks to indicate that To establish a Fast Ethernet connection using a
power is being supplied to an attached powered miniGBIC port, you will need to install a MFEFX1
device (PD) on the corresponding port (1 through (100BASE-FX) or MFELX1 (100BASE-LX) 100SFP
6, 13 through 18). Transceiver and use fiber optic cabling.
100M (7-12, 19-24) (Amber) Lights up to
indicate a functional 100 Mbps connection on NOTE: On the SLM224P, MiniGBIC ports are
the corresponding port (7 through 12, 19 through shared with Gigabit Ethernet ports. If a miniGBIC
24) with an attached device. port is used, then the shared Gigabit Ethernet
LNK/ACT (G1-G2) (Green) Lights up to indicate port on the Switch cannot be used. The following
a functional 10/100/1000 Mbps network link table defines the shared port mapping of the
through the corresponding port (G1 through G2) SLM224P Switch.
over that port.
SLM224P Shared Port Mapping
Gigabit (G1-G2) (Amber) Lights up to indicate
a functional 1000 Mbps connection on the miniGBIC Port Gigabit Port
miniGBIC 1 Port G1
attached device.
Reset To reboot the Switch, press and hold the miniGBIC 2 Port G2
Reset Button for approximately five seconds. To
reset the Switch settings to the factory defaults,
press and hold the Reset Button for approximately Back Panel
ten seconds.
Ethernet 1-24 The Switch is equipped with 24 The power port is located on the back panel of the Switch.
They can operate in half- and full-duplex modes. Back Panel of the SLM224P
automatically detect the speed of the device POWER The Power port is where you connect
connected to it (10 Mbps or 100 Mbps), and the AC power.
adjust its speed and duplex accordingly.

Chapter 3 Installation
Chapter 3: Pre-Installation Considerations

Installation Fast Ethernet Considerations
If you are using the Switch for Fast Ethernet (100 Mbps)
Overview applications, you must observe the following guidelines:
This chapter will explain how to connect network devices Full-Duplex Considerations
to the Switch. The following diagram shows a typical
network configuration. The Switch provides full-duplex support for its RJ-45
ports. Full-duplex operation allows data to be sent and
received simultaneously, doubling a port’s potential data
Cable/DSL Uplink via Fiber to
Internet Modem Router Wireless Access Point Server Switch
throughput. If you will be using the Switch in full-duplex
mode, the maximum cable length using Category 5 cable
is 100 meters.
1000BASE-T Cable Requirements

All Category 5 UTP cables that are used for 100BASE-TX
connections should also work for 1000BASE-T, providing
that all four wire pairs are connected. However, it is
recommended that for all critical connections, or any
10/100/1000 10/100
Desktop Notebook
new cable installations, Category 5e (enhanced Category
5) or Category 6 cable should be used. The Category
Typical Network Configuration for the SLM2048
5e specification includes test parameters that are only
When you connect your network devices, make sure you recommendations for Category 5. Therefore, the first
do not exceed the maximum cabling distances, which are step in preparing existing Category 5 cabling for running
listed in the following table: 1000BASE-T is a simple test of the cable installation to be
sure that it complies with the IEEE 802.3ab standards.
Maximum Cabling Distances
From To Maximum Distance

Positioning the Switch
Before you choose a location for the Switch, observe the
Switch Switch or Hub 100 meters following guidelines:
Hub† Hub 5 meters • Make sure that the Switch is accessible and that the
cables can be connected easily.
Switch or Hub† Computer 100 meters • Keep cabling away from sources of electrical noise,
†A hub refers to any type of 100 Mbps hub. A 10 Mbps hub connected power lines, and fluorescent lighting fixtures.
to another 10 Mbps hub can span up to 100 meters.
• Position the Switch away from water and moisture
sources.
• To ensure adequate air flow around the Switch, be
sure to provide a minimum clearance of two inches
(50 mm).
• Do not stack free-standing Switches more than four
units high.
Placement Options
There are two ways to physically install the Switch, either
set the Switch on its four rubber feet for desktop placement
or mount the switch in a standard-sized, 482,6-mm wide,
1U-high rack for rack-mount placement.

Desktop Placement To rack-mount the Switch in any standard 482,6-mm wide,

1U high rack, follow the instructions described below.
• Attach the rubber feet to the recessed areas on the
bottom of the Switch. 1. Place the Switch on a hard flat surface with the front
panel facing you.
• Place the Switch on a desktop near an AC power
source. 2. Attach a rack–mount bracket to one side of the Switch
with the supplied screws and secure the bracket
• Keep enough ventilation space for the switch and tightly.
check the environmental restrictions mentioned in the
Specifications Appendix as you are placing the Switch.
• Connect the Switch to network devices according to
the Hardware Installation instructions below.
Attaching the Brackets
3. Follow the same steps to attach the other bracket to

the opposite side.
4. After the brackets are attached to the Switch, use
Attaching the Switch’s Rubber Feet suitable screws to securely attach the brackets to any
standard 482,6-mm rack.
Rack-Mount Placement
When rack-mounting the Switch, please observe the
following guidelines
• Elevated Operating Ambient If installed in a closed
or multi-unit rack assembly, the operating ambient
temperature of the rack environment may be greater
than room ambient. Therefore, consideration should
be given to installing the equipment in an environment
compatible with the maximum ambient temperature
(Tma) specified by the manufacturer.
• Reduced Air Flow Installation of the equipment
in a rack should be such that the amount of air flow
required for safe operation of the equipment is not
compromised.
Mounting in Rack
• Mechanical Loading Mounting of the equipment in
the rack should be such that a hazardous condition is 5. Connect the Switch to network devices according to
not achieved due to uneven mechanical loading. the Hardware Installation instructions below.
• Circuit Overloading Consideration should be given
to the connection of the equipment to the supply Hardware Installation
circuit and the effect that overloading of the circuits
might have on overcurrent protection and supply To connect network devices to the Switch, follow these
wiring. Appropriate consideration of equipment instructions:
nameplate ratings should be used when addressing 1. Make sure all the devices you will connect to the Switch
this concern. are powered off.
• Reliable Earthing Reliable earthing of rack-mounted 2. For a 10/100 Mbps device:
equipment should be maintained. Particular attention
• All models: Connect a Category 5 Ethernet network
should be given to supply connections other than
direct connections to the branch circuit (e.g. use of cable to one of the numbered ports on the Switch.
power strips).
For a 1000 Mbps device: Ethernet Ports Shared with miniGBIC Ports

• SLM2048 and SLM2024: Connect a Category 5e Port Shared Port Shared
Ethernet network cable to one of the numbered Switch with with
ports on the Switch. miniGBIC1 miniGBIC2
• SLM248G, SLM248P, SLM224G, SLM224P: Connect SLM2048 24 48
a Category 5e Ethernet network cable to port G1 or
port G2 on the Switch. SLM2024 12 24
For a 10/100 Mbps PoE device: SLM248G, SLM248P,
G1 G2
• SLM248P: Connect a Category 5 Ethernet cable to SLM224G, SLM224P
one of ports 1-12 or ports 25-36 on the Switch.
To establish a Gigabit Ethernet connection using a miniGBIC
• SLM224P: Connect a Category 5 Ethernet cable to port, you will need to install a MGBT1, MGBSX1, or MGBLH1
one of ports 1-6 or ports 13-18 on the Switch. Gigabit expansion module and use Category 5e cabling or
3. Connect the other end of the network cable to a PC or fiber optic cabling.
other network device. To establish a Fast Ethernet connection using a miniGBIC
4. Repeat steps 2 and 3 to connect additional devices. port, you will need to install a MFEFX1 (100BASE-FX) or
MFELX1 (100BASE-LX) 100SFP Transceiver and use fiber
SLM248P and SLM224P: If a 802.3af-compliant PoE
optic cabling.
device is connected to one of the Switch’s PoE ports,
the Switch automatically supplies the required power. The hardware installation is complete. Proceed to
“Chapter 4: Configuration Using the Web-based Utility”,
5. If you are using a miniGBIC port, then connect a
for directions on how to set up the Switch.
miniGBIC module to a miniGBIC port. For more detailed
instructions, refer to “Uplinking the Switch“.
6. Connect the supplied power cord to the Switch’s
power port, and plug the other end into an electrical
outlet. When connecting power, always use a surge
protector.
IMPORTANT: Make sure you use the power

cord that is supplied with the Switch. Use of a
different power cord could damage the Switch.
7. Power on the devices connected to the Switch. Each

active port’s corresponding LED will light up on the
Switch.
Uplinking the Switch

To uplink the Switch using a 1000 Mbps Ethernet port,
connect one end of a Cat 5e (or better) Ethernet network
cable to one of the Gigabit ports, and then connect the
other end of the cable into the peripheral device’s uplink
port. MDI/MDIX will automatically detect the speed and
cable type.
To uplink the Switch using the miniGBIC port, connect
a miniGBIC module to a miniGBIC port whose shared
Ethernet port is not being used (a miniGBIC port and its
shared Ethernet port cannot be used at the same time).
The following table shows which Ethernet ports are shared
with the miniGBIC ports.
Business Series Smart Gigabit Ethernet Switch 10

Chapter 4 Configuration Using the Web-based Utility
Chapter 4: Each time you log in, the web-based utility first displays
the Setup tab’s Summary screen. To access another screen,
Configuration Using the you first select the appropriate category from among the
10 tabs that appear at the top of the screen: Setup, Port
Web-based Utility Management, VLAN Management, Statistics, Security,
QoS, Spanning Tree, Multicast, Admin, and Logout.
Then, select the desired screen from the list directly below
This chapter describes the features included in the Web- the tab names.
based Utility. All features shown in this chapter, unless
specifically identified, are included in the all of Smart
Switches. Unique features for specific Switches are noted.
Setup
The Setup tab contains the Summary screen. This screen
NOTE: The web-based utility is optimized for displays basic system information.
a screen resolution of 1024 x 768. Internet
Explorer version 5.5 or above is recommended.. Setup > Summary
The Summary screen displays a summary of Switch
To use the utility, open your web browser, enter
information. The settings shown cannot be modified
http://192.168.1.254 in the Address field, then press Enter.
from the Summary screen; however, many of them can be
modified from the Setup tab’s Network Settings screen.
Address Bar
NOTE: The default IP address is 192.168.1.254.

If you have changed the IP address or are using
DHCP to assign it, enter the new IP address
instead. The computer you use for configuration
should be on the same subnet as the Switch.
The Login screen appears. Enter admin in the Username

field and enter the password in the Password field. If this is
the first time you are using the utility, leave the Password
blank. Then press OK to log in. The Setup tab’s Summary
screen appears. Setup > Summary
(After you have completed your first login, for security At the top of the Summary screen, an image of the Switch‘s
purposes it is recommended that you set a password at front panel provides the following color-coded status
a later time. For detailed information on changing the information for the Switch’s Ethernet ports:
password, refer to section “Admin > User Authentication.”)
Green Indicates that the port has a connection.
Gray Indicates that the port has no connection.
Orange Indicates that the port has been closed down by
the administrator.
Click on a port to display that port’s statistics.
NOTE: The port colors in the Summary screen

are not related to the colors of the LEDs on the
Switch’s ports. The port LEDs display different
status information, as described in “Chapter 2:
Overview.”
The Summary screen two sections: Device Information and

System Information. These are described below.
Login Screen

Device Information Boot Version Displays the current boot version of the
Switch.
System Name Displays the name of the Switch, if one has
been entered on the Setup tab’s Network Settings screen. Firmware Version Displays the Switch’s current software
version
IP Address The IP address assigned to the Switch. The
Switch’s default IP address is 192.168.1.254. This setting System Location Displays the location of the system if it
can be configured from the Setup tab’s Network Settings has been defined. This setting can be configured from the
screen. Setup tab’s Network Settings screen.
Subnet Mask The Subnet Mask assigned to the Switch. System Contact The name of the administrator appears
The default subnet mask is 255.255.255.0. This setting here, if one has been defined. This setting can be configured
can be configured from the Setup tab’s Network Settings from the Setup tab’s Network Settings screen.
screen. System Up Time Displays the length of time that has
DNS Server The IP address of your ISP’s server that elapsed since the Switch was last reset.
translates the names of websites into IP addresses. This Current Time Displays the current time. This setting can
setting can be configured from the Setup tab’s Network be configured from the Setup tab’s Time screen.
Settings screen.
Click Save Settings to save your changes. Click Cancel
Default Gateway The IP address of the gateway router Changes to cancel your changes.
between the Switch and management stations on other
network segments. The default Gateway Address is Setup > Network Settings
0.0.0.0. This setting can be configured from the Setup
tab’s Network Settings screen.
NOTE: The Default Gateway cannot be

configured if the system IP address is set to
192.168.1.254. (The system IP Address is set
using Setup > Network Settings.).
Address Mode Specifies whether IP functionality is

enabled via manual configuration (Static) or Dynamic
Host Configuration Protocol (DHCP). This setting can be
configured from the Setup tab’s Network Settings screen.
The default setting is DHCP.
Setup > Network Settings
Base MAC Address Displays the MAC address of the
Switch. The Network Settings screen allows you to edit the
following information. Many of these fields are displayed
System Information on the Summary screen where they cannot be edited.
NOTE: The Jumbo Frame setting applies ONLY Identification

to the SLM2024 and SLM2048 Smart Switches.
System Name Specifies the name of the Switch. Enter
Other Smart Switches do not support this
the name into the text field provided. By default, a system
feature.
name is not defined.
Jumbo Frame (SLM2024 and SLM2048 only) This System Location This field is used to enter a description
setting enables or disables Jumbo frames on the Switch. of where the Switch is physically located, such as 3rd
A maximum packet size of 9 KB is supported. Jumbo Floor.
frames allow data to be transmitted using fewer frames, System Contact Enter the name of the administrator
providing lower overhead, quicker processing time, and responsible for the system.
fewer interruptions. Select either Enable to enable the
Jumbo frames feature, or Disable (default) to disable it. Base MAC Address Displays the physical address of the
Switch.
Model Name Displays the model name of the Switch.
Hardware version Displays the Switch’s current hardware
version.

IP Configuration Setup > Time

Management VLAN This drop-down menu allows you to The Time screen allows you to configure the time settings
select the Management VLAN. The default value is 1. for the Switch.
WARNING: The Management VLAN must be

set to 1 (default VLAN) if the system IP address
(IP Address field) is set to 192.168.1.254.
Otherwise, you may not be able to access the
system.
IP Address Mode Specifies whether IP functionality is

enabled via manual configuration (Static) or Dynamic
Host Configuration Protocol (DHCP). Select Static or
DHCP from the drop-down menu. Selecting Static will
allow you to enter a static IP address, subnet mask and
default gateway using the text field provided. The default
setting is DHCP.
IP Address If you are using a static IP address, enter Setup > Time
the IP address here. The Switch’s default IP address is
192.168.1.254. Local Time
Subnet Mask If you are using a static IP address, enter This is where you set the system date and time for the
the subnet mask for the currently configured IP address. Switch. All values noted as “two-digit” must consist of two
The default subnet mask is 255.255.255.0. digits; values less than 10 must have a leading zero (for
Default Gateway If you are using a static IP address, example, 01 instead of 1).
enter the IP address of the default gateway. The default Hours Enter the two-digit hour here.
value is 0.0.0.0.
Minutes Enter the two-digit minutes here.
DNS Server If you are using a static IP address, enter the
IP address of the DNS server. A second DNS address can be Seconds Enter the two-digit seconds here.
specified in the additional text field provided. Month Enter the two-digit month here.
Click Save Settings to save your changes. Click Cancel Day Enter the two-digit day here.
Changes to cancel your changes.
Year Enter the last two digits of the year here (for example,
07 instead of 2007).
Time Zone Select your time zone from the drop-down
menu. Time zones are identified by the difference between
Greenwich Mean Time (GMT) and local time.
Daylight Saving
This is where you configure Daylight Saving Time.
Daylight Saving Enable daylight saving time by checking
the checkbox.
Time Set Offset Custom daylight saving time is set by
entering the time difference in minutes into the Time Set
Offset field. The default offset is 60 minutes.

Port Management Flow Control The type of flow control currently in use.
Type The port type.
The Port Management tab contains the Port Settings,
Link Aggregation, and LACP screens. On the SLM224P LAG The LAG to which the port belongs, if the port is a
and SLM248P only, this tab also contains the PoE Power LAG member.
Settings screen.
Port Configuration
Port Management > Port Settings The Port Configuration screen lets you configure a port.
You use the Port Settings screen to display the speed, You can enable/disable the interface, and set the port’s
duplex mode, and flow control used on specific ports, or capability advertisements, speed, duplex mode, and flow
use to detect the connection settings used by the attached control. To use this screen, click Detail in the Detail column
device. Use the full-duplex mode on ports whenever on the Port Settings screen.
possible to double the throughput of switch connections.
Flow control should also be enabled to control network
traffic during periods of congestion and prevent the loss
of packets when port buffer thresholds are exceeded. The
Switch supports flow control based on the IEEE 802.3x
standard.
The information on the Port Settings screen is read-only.
To edit this information, click Details to the right of a
port’s information to edit that port’s settings using the
Port Configuration screen. For detailed information on the
Port Configuration screen, refer to the “Port Configuration“
section.
Port Management > Port Settings> Port Configuration
The Port Configuration screen contains the following fields

(“Read-only” indicates that a field cannot be edited).“
Port The port number. To edit the information for
another port, select the port from the drop-down menu.
(Port numbers consist of either “e” for Ethernet, or “g” for
Gigabit, followed by the appropriate number.)
Description The user-defined port description of up to
64 characters. This field is blank by default.
Port Management > Port Settings
Port Type (Read-only) The port’s connection type and
The Port Settings screen displays the following information. speed. The types are:
For information on these settings, refer to the “Port
Configuration“ section. • copper The port has a copper connection.
Port The port number. • ComboC The Gigabit port has a copper connection.
Description The user-defined port description. • ComboF The Gigabit port has a fiber optic
connection.
Administrative Status The port’s administrative status. The port speed is prefixed onto the type, for example
Link Status The port’s operational status. 10M-copper indicates a 10 Mbps copper connection.
Speed The port’s configured rate in Mbps. Admin Status The port’s administrative status. Select
either Up or Down to enable or disable traffic forwarding
Duplex The port’s current duplex mode. through the port.
MDI/MDIX The port’s MDI/MDIX type. Current Port Status (Read-only) The port’s connection
status, either Up or Down.
Reactivate Suspended Port If the port has been Flow Control Select Enable or Disable to manually
suspended, select this checkbox to reactivate the port. enable or disable flow control, or select Auto-Negotiation
for automatic selection of flow control on the port.
Operational Status (Read-only) Displays whether the
port is operational or non-operational. Current Flow Control (Read-only) The current flow
control setting.
Admin Speed Use this to manually set the port’s
configured transmission rate in Mbps. You can select 10M, MDI/MDIX Select the port’s MDI/MDIX type, either MDI,
100M, or 1000M (Gigabit ports only). Before you change MDIX, or Auto (automatically detect type). The MDI
this setting, make sure that Auto Negotiation is disabled. setting is used if the port is connected to an end station.
The MDIX setting is used if the port is connected to a hub
Current Port Speed (Read-only) The port’s current rate
or another switch.
in Mbps.
Current MDI/MDIX (Read-only) The port’s current MDI/
Admin Duplex The port’s duplex mode, either Full or
MDIX type.
Half.
LAG (Read-only) The LAG to which this port belongs, if
Current Duplex Mode (Read-only) The port’s current
the port is a LAG member.
duplex mode.
Click Save to save the settings and leave the screen open.
Auto Negotiation Select Enable (default) or Disable
Click Save & Close to save the settings and close the
to enable or disable Auto-Negotiation on the port. Auto-
screen. Click Close to close the screen without saving the
Negotiation allows a port to advertise its transmission rate,
settings.
duplex mode, and flow control settings to other ports.
Current Auto Negotiation (Read-only) The port’s current Port Management > Link Aggregation
Auto-Negotiation status.
You can create multiple links between devices that work
Admin Advertisement Select the speed(s) and duplex as one virtual, aggregate link. This is known as a Link
mode(s) that the port will advertise. The available speeds Aggregrated Group (LAG). LAGs offers a dramatic increase
are determined by the port type. The following capabilities in bandwidth for network segments where bottlenecks
are supported. exist, as well as providing a fault-tolerant link between two
• Max Capability The port advertises all speeds and devices. You can create up to eight LAGs on the Switch.
duplex mode settings. Each LAG can contain up to eight ports.
• 10 Half The port advertises 10 Mbps half-duplex
operation.
• 10 Full The port advertises 10 Mbps full-duplex
operation.
• 100 Half The port advertises 100 Mbps half-duplex
operation.
• 100 Full The port advertises 100 Mbps full-duplex
operation.
• 1000 Full (Gigabit ports only) The port advertises
1000 Mbps full-duplex operation.
Current Advertisement (Read-only) The speed
and duplex mode settings that the port is currently
Port Management > Link Aggregation
advertising.
Neighbor Advertisement (Read-only) The speed and LAG The LAG number (1-8).
duplex mode settings that the neighbor port (the port to Description The user-defined description for the LAG.
which the selected port is connected) is advertising. If the
port has no neighbor port, this field displays “Unknown.” Admin Status The administrative status of the interface.
To change it, select Up to enable the interface, or Down
Back Pressure Select Enable or Disable (default) to to disable it.
enable or disable Back Pressure mode on the port.
Type Indicates if a LAG has been manually configured
Current Back Pressure (Read-only) The current Back (static) or dynamically set through LACP.
Pressure mode on the port.
Link Status Displays the status of the link.
Speed Displays the port speed. Operational Status (Read-only) Displays whether the
LAG is operational or non-operational.
Duplex Displays the duplex mode.
Admin Auto Negotiation Select Enable (default) or
Flow Control Displays the flow control.
Disable to enable or disable Auto-Negotiation on the
LAG Mode Displays the LAG mode. LAG. Auto-Negotiation allows a LAG to advertise its
Detail To create a new LAG, click Detail in the Detail transmission rate, duplex mode, and flow control settings
column to display the Link Aggregation detail screen. to other LAGs.
Current Auto Negotiation (Read-only) The LAG’s current
LAG Configuration Auto-Negotiation status.
The Link Aggregation detail screen lets you configure a Admin Advertisement Select the capabilities (speeds
LAG. You can create a LAG, select its ports, enable/disable and duplex modes) that the LAG will advertise. The
the LAG, and set the capability advertisements, speed, available speeds are determined by the LAG port type.
duplex mode, and flow control. To use this screen, click The duplex mode must be full-duplex. The following
Detail on the Port Settings screen. capabilities are supported.
• Max Capability The LAG advertises all port speeds in
full-duplex mode.
• 10 Full The LAG advertises 10 Mbps full-duplex
operation.
• 100 Full The LAG advertises 100 Mbps full-duplex
operation.
• 1000 Full (Gigabit ports only) The LAG advertises
1000 Mbps full-duplex operation.
Current Advertisement (Read-only) The speed
and duplex mode settings that the LAG is currently
advertising.
Neighbor Advertisement (Read-only) The speed and
duplex mode settings that the neighbor port (the port to
which the selected LAG is connected) is advertising. If the
Port Management > Link Aggregation > Detail
LAG has no neighbor port, this field displays “Unknown.”
LAG The LAG number (1-8). To display or edit another Admin Speed Use this to manually set the LAG’s
LAG, select the number from the drop-down menu. configured transmission rate in Mbps. You can select 10M,
Description The user-defined LAG description of up to 100M, or 1000M (Gigabit ports only). Before you change
64 characters. This field is blank by default. this setting, make sure that Admin Auto Negotiation is
disabled.
LACP Select the checkbox to enable Link Aggregation
Control Protocol (LACP). Current LAG Speed (Read-only) The LAG’s current rate in
Mbps.
LAG Type (Read-only) The LAG type. The possible values
are: Admin Flow Control Select Enable or Disable to
manually enable or disable flow control, or select Auto-
• eth100m The LAG contains 100 Mbps Ethernet ports. Negotiation for automatic selection of flow control.
• eth1000m The LAG contains 1000 Mbps Ethernet Current Flow Control (Read-only) The current flow
ports. control setting.
Admin Status The LAG’s administrative status. Select Select Ports To add a port to the LAG, select its checkbox
either Up or Down to enable or disable the LAG. in this section. You can select up to 8 ports per LAG.
Current Status (Read-only) The LAG’s status, either Up or Click Save to save the settings and leave the screen open.
Down. Click Save & Close to save the settings and close the
Reactivate Suspended LAG If the LAG has been screen. Click Close to close the screen without saving the
suspended, select this checkbox to reactivate the LAG. settings.

Port Management > LACP Port Management > PoE Power Settings
In addition to LAGs that you create by manually grouping
ports together, you can also use the Link Aggregation NOTE: This section applies ONLY to the
Control Protocol (LACP) to automatically negotiate a LAG SLM224P and SLM248P Smart Switches.
link between the Switch and another network device.
The LACP screen contains fields for configuring LACP LAGs. The PoE Power Settings screen allows you to configure the
This screen is divided into three parts: Global Parameter, Power over Ethernet (PoE) ports on the Switch.
Port Priority, and LACP Port Table.
Port Management > PoE Power Settings

Port Management > LACP
Port Displays the port number.
Global Parameter Admin Status Check the checkbox to enable PoE power
to be supplied to the connected device.
LACP System Priority The global LACP priority value,
from 1 to 65535. The default value is 1. Priority Select Critical, High, or Low (default) from the
drop‑down menu to set the priority of the port.
Port Priority
Power Allocation (milliwatts) Sets the maximum power
Port The port number to which the timeout and priority in milliwatts that can be supplied to the port.
values are assigned. To configure a different port, select it
Power Consumption (milliwatts) Displays the power
from the drop-down menu. If you do not see the port you
currently being used by the connected PoE device.
want, click Next in the LACP Port Table.
Click Save Settings to save the changes, or click Cancel
LACP Port Priority Defines the LACP priority value for
the port, from 1 to 65535. The default value is 1.
LACP Timeout The administrative LACP timeout value.
Select either Short or Long (default).
Admin Key (Read-only) A channel will only be formed
between ports with the same admin key. This only applies
to ports located on the same switch.
When you are finished entering the settings above, click
Update to apply the settings.
LACP Port Table

This section provides a read-only display of the current
LACP settings.
After you are finished setting the LACP parameters,
click Save Settings to save the settings, or click Cancel

VLAN Management VLAN Management > Port Settings

A VLAN is a group of ports that can be located anywhere The Port Settings screen allows you to configure the ports
in the network, but communicate as though they belong in a VLAN.
to the same physical segment.
VLANs help to simplify network management by allowing
you to move devices to a new VLAN without having
to change any physical connections. VLANs can be
easily organized to reflect departmental groups (such
as Marketing or R&D), usage groups (such as e-mail), or
multicast groups (used for multimedia applications such
as videoconferencing). You can create up to 128 VLANs on
the Switch.
VLAN Management > Create VLAN

The Create VLAN screen lets you create and configure
global parameters for VLANs.
VLAN Management > Port Settings
You can configure VLAN behavior for specific ports,

including the accepted frame type, VLAN identifier (PVID),
and ingress filtering.
Port The number of the port.
Acceptable Frame Type This specifies the type of frames
that the port will accept. If All (default) is selected, the
port will accept all frame types, including tagged or
untagged frames. If Tagged is selected, the port accepts
only tagged frames. When set to All, any untagged frames
that are received are assigned to the default VLAN.
PVID Use this field to select the VLAN ID that will be
VLAN Management > Create VLAN assigned to untagged frames received on the port.
Valid IDs are 1 (default) to 4093. VLAN 4094 is reserved
Single VLAN for internal use. VLAN 4095 is defined per standard and
industry practice as the Discard VLAN. Frames tagged for
To create a single VLAN, enter the VLAN ID and VLAN the Discard VLAN are dropped.
Name, up to 32 characters long, and click Add.
Ingress Filtering Enables or disables Ingress filtering
VLAN ID ID of configured VLAN (2-4093, no leading on the port. Ingress filtering discards packets that do not
zeroes). include an ingress port. The default is Enabled.
VLAN Name Name of the VLAN. (1 to 32 characters) LAG Displays the LAG, if any, to which the port belongs. A
VLAN Range port’s LAG settings override the VLAN port settings.
Click Save Changes to save your changes, or click Cancel
To create a range of VLANs, enter the range of their IDs in
Changes to cancel.
the VLAN Range fields and then click Add Range.
VLAN Table VLAN Management > Port to VLAN

This section lists the current VLANs in tabular format. For You use the Port to VLAN screen to add ports to a VLAN and
each VLAN, it displays the VLAN’s ID, name, and status. The delete ports from a VLAN. When you add a port to a VLAN,
status values are Static (user-defined VLAN) or Default you also specify whether the port is tagged or untagged.
(default VLAN). The total number of VLANs is also shown. The Port to VLAN screen contains a Port Table with VLAN
To remove a VLAN or a range of VLANs, select the VLANs in parameters for each port. To add a port to or delete a
the VLAN Table, then click Delete. port from the VLAN, you select the port’s appropriate
configuration options from this table.
VLANs Displays the IDs of the VLANs to which the port

belongs, prefixed by “T” if the port is tagged or “U” if the
port is untagged in that VLAN.
LAG Displays the LAG to which the port belongs, if any.
If a port belongs to a LAG, it cannot belong to a VLAN.
However, the LAG to which the port belongs can be
configured to belong to a VLAN.
Join VLAN to Port

The Join VLAN to Port screen appears when you click the
Join VLAN button for a port in the VLAN to Port screen. You
use this screen to configure the port’s VLAN membership.
VLAN Management > Port to VLAN
Select VLAN Select the ID of the VLAN whose port

membership you are configuring. For each port in the
VLAN, select the appropriate configuration option:
• Tagged The interface is a member of the VLAN. All
packets transmitted by the port will be tagged and will
carry VLAN information.
• Untagged The interface is a member of the VLAN. All
packets transmitted by the port will be untagged and
will not carry VLAN information.
• Excluded The interface is excluded from the VLAN. VLAN Management > VLAN to Port > Join VLAN to Port
This is the default option.
Select VLAN This contains two fields. The field on the
left side of the screen lists the IDs of all available VLANs
VLAN Management > VLAN to Port to which the port can belong, while the field on the right
The VLAN to Port screen displays each port’s VLAN side lists the IDs of the VLANs to which the port already
membership information. It is also used to add a port to or belongs. Each VLAN ID is prefixed by “T” if the port is
delete a port from a VLAN. tagged or by “U” if the port is untagged on the respective
VLAN.
Add To add the selected port to one of the available
VLANs, select the desired VLAN from the left side of the
screen, then select the desired Tagging option and click
Add. The VLAN ID will appear on the right side with the
appropriate prefix indicating a tagged or untagged port.
Remove To remove the selected port from a VLAN,
select the VLAN from the right side of the screen and
click Remove. The VLAN ID appears on the left side of the
screen without the “T” or “U” prefix.
Tagging When you are adding a port to a VLAN, select
the appropriate option to specify whether the port is
Tagged (default) or Untagged.
VLAN Management > VLAN to Port Click Save to save your changes and leave the screen
open, Save & Close to save your changes and close the
Port The number of the port being configured. screen, or click Close to close the screen without saving
Join VLAN To configure the port’s VLAN membership, your changes.
press Join VLAN to bring up the Join VLAN to Port screen.

Statistics • Unicast Packets Displays the number of Unicast

packets transmitted from the selected interface.
The Statistics tab contains the Interface Statistics screen,
• Multicast Packets Displays the number of Multicast
which lets you display statistics for a specified interface.
Statistics > Interface Statistics • Broadcast Packets Displays the number of Broadcast
Ethernet-like
This section displays the following statistics for the
selected interface.
Frame Check Sequence (FCS) Errors Displays the
number of FCS errors received on the selected interface.
Single Collision Frames Displays the number of single
collision frames received on the selected interface.
Late Collisions Displays the number of late collision
frames received on the selected interface.
Oversize Packets Displays the number of oversize packet
errors on the selected interface.
Statistics > Interface Statistics
Internal MAC Receive Errors Displays the number of
This screen allows you to display statistics for the Ethernet internal MAC received errors on the selected interface.
port or LAG that you specify. You can also specify the rate
at which the display will be refreshed. Received Pause Frames Displays the number of received
paused frames on the selected interface.
Interface To display statistics for an Ethernet port, select
Port, then select the desired port from the drop-down Transmitted Pause Frames Displays the number of
menu. To display statistics for a LAG, select LAG and then paused frames transmitted from the selected interface.
select the desired LAG from the drop-down menu. Clear Counters Click the Clear Counters button to reset
Refresh Rate Select the rate at which to refresh the all the counters on this screen to zero.
statistics display. The values are 15 sec, 30 sec, 60 sec, and
No Refresh (default).
Interface
This section displays statistics for the packets transmitted
and received on the selected interface.
Receive Statistics Statistics on received packets
• Total Bytes (Octets) Displays the number of octets
received on the selected interface.
• Unicast Packets Displays the number of Unicast
packets received on the selected interface.
• Multicast Packets Displays the number of Multicast
• Broadcast Packets Displays the number of Broadcast
• Packets with Errors Displays the number of error
packets received from the selected interface.
Transmit Statistics Statistics on transmitted packets
• Total Bytes (Octets) Displays the number of octets
transmitted from the selected interface.

Security Table
This part of the 802.1x Settings screen displays a summary
Security > 802.1x Settings of the settings that appear in the Parameters section of the
The 802.1x Settings screen is used to configure a port’s screen. If you click More Details, the settings described in
802.1x authentication settings. the “Setting Timer” section are added to the table.
Click Save Settings to apply the changes, or Cancel
Changes to cancel the changes.
Setting Timer
The Setting Timer screen appears when you click Setting
Timer on the 802.1x Settings screen. You use the Setting
Timer screen to configure a port’s 802.1x functionality.
Security > 802.1x Settings
Port-based authentication enables authenticating system

users on a per-port basis via an external server. Only
Security > 802.1x Settings > Setting Timer
authenticated and approved system users can transmit
and receive data. Ports are authenticated via a RADIUS Port Displays the port name.
server using the Extensible Authentication Protocol (EAP).
Reauthentication Period Specifies the number
Parameters of seconds after which a connected client must be
reauthenticated. The range is 300 to 4294967295
Enable 802.1x Select the checkbox to enable 802.1x seconds. The default value is 3600 seconds.
authentication. The default is not enabled.
Quiet Period Specifies the time that a switch port waits
Interface The interface on which to configure 802.1x. after Max EAP Requests is exceeded before attempting
• Port Select the port from the drop-down menu. to acquire a new client. The range is 0 to 65535 seconds.
The default is 60 seconds.
Status Port Control Sets the port authentication mode
top one of the following options: Resending EAP Specifies the time that the switch waits
for a response to an EAP request/identity frame from the
• ForceAuthorized (Default) Forces the port to grant client before retransmitting an EAP packet. The range is 1
access to all clients, either dot1x-aware or otherwise. to 65535 seconds. The default is 30 seconds.
• ForceUnauthorized Forces the port to deny access Max EAP Requests Specifies the maximum number
to all clients, either dot1x-aware or otherwise. of times the switch port will retransmit an EAP request
• Auto Requires a dot1x-aware client to be authorized packet to the client before it times out the authentication
by the authentication server. Clients that are not dot1x- session. The range is 1 to 10 times. The default is 2 retries.
aware will be denied access. Supplicant Timeout Displays the number of seconds that
Enable Periodic Reauthentication Select the checkbox lapses before EAP requests are resent to the supplicant. The
to permit periodic port reauthentication. range is 1 to 65535 seconds. The default is 30 seconds.
Setting Timer Click this button to open the Setting Timer Server Timeout The number of seconds that lapses
screen to configure ports for 802.1x functionality. before the switch resends a request to the authentication
server The range is 1 to 65535. The default is 30 seconds.
Update If you click this button, your changes are saved
and appear immediately in the screen’s Table section. Click Save to save your changes and leave the screen
open. Click Save & Close to save your changes and close
the screen. Click Close to close the screen without saving
your changes.
Security > Port Security Learning Mode Defines the locked port type. This field
is enabled only if Lock Interface is not selected. The
The Port Security screen is used to configure a port’s possible values are:
security settings.
• Classic Lock Locks the port using the classic lock
mechanism. The port is immediately locked, regardless
of how many addresses have already been learned.
• Limited Dynamic Lock Locks the port by deleting
the current dynamic MAC addresses associated with
the port. The port learns up to the maximum number
of addresses allowed on the port. Both relearning and
aging MAC addresses are enabled.
In order to change the Learning Mode, the Lock Interface
must be unselected. Once the Learning Mode is changed,
the Lock Interface can be reinstated.
Max Entries Specifies the number of MAC addresses
that can be learned on the port. This field is enabled only
if Learning Mode is set to Limited Dynamic Lock. The
Security > Ports Security
default value is 1.
Network security can be increased by limiting access on Action on Violation Indicates the action to be applied to
a specific port only to users with specific MAC addresses. packets arriving on a locked port. The possible values are:
MAC addresses can be dynamically learned or statically
• Discard Discards packets from any unlearned source.
configured.
This is the default value.
Locked port security monitors both received and learned
• Forward Forwards packets from an unknown source
packets that are received on specific ports. Access to the
locked port is limited to users with specific MAC addresses. without learning the MAC address.
These addresses are either manually defined on the port, • Shutdown Discards packets from any unlearned
or learned on that port up to the point when it is locked. source and shuts down the port. The port remains shut
When a packet is received on a locked port, and the down until reactivated, or until the device is reset.
packet’s source MAC address is not tied to that port (either
Update If you click this button, your changes are saved
it was learned on a different port, or it is unknown to the
and appear immediately in the table at the bottom of the
system), the protection mechanism is invoked, and can
Port Security screen.
provide various options. Unauthorized packets arriving at
a locked port are either: The lower portion of the Port Security screen displays
a summary of the settings in the upper portion of the
• Forwarded
screen. The settings are displayed for each of the ports
• Discarded on the Switch.
• Cause the port to be shut down Click Save Settings to apply the changes, or Cancel
Locked port security also enables storing a list of MAC Changes to cancel the changes.
addresses in the configuration file. The MAC address list
can be restored after the device has been reset.
Disabled ports can be reactivated from the Port Settings
screen of the Port Management tab.
Interface Select Port or LAG, then select the desired
interface from the appropriate drop-down menu.
Lock Interface Select this option to lock the interface.
The default is not selected (interface not locked).

Security > IP Access List Security > Storm Control

Use the IP Access List (also known as Management Access The Storm Control screen is used to configure broadcast
List) screen to specify IP addresses that are to be allowed and multicast storm control.
to manage the device, using an IP address and wildcard
mask.
Security > Storm Control
Security > IP Access List Storm Control enables limiting the amount of Multicast and
Broadcast frames accepted and forwarded by the Switch.
IP Address Enter the IP address to be allowed. A Broadcast Storm results when an excessive amount of
Wildcard Mask Enter the IP address wildcard mask. broadcast messages is simultaneously transmitted across
Wildcard masks specify which bits are used and which a network by a single port. Forwarded message responses
bits are ignored. A wild card mask of 255.255.255.255 are heaped onto the network, straining network resources
indicates that no bit is important. A wildcard of 0.0.0.0 or causing the network to time out.
indicates that all the bits are important. For example, if the To enable Storm Control on a port, you specify the packet
source IP address is 149.36.184.198 and the wildcard mask type (broadcast/multicast) and maximum transmission
is 255.36.184.00, the first eight bits of the IP address are rate. The system measures the incoming Broadcast and
ignored, while the last eight bits are used. Multicast frame rates separately on each port and discards
Add to List Click this button to save the IP address and frames when the rate exceeds the specified maximum.
Wildcard Mask. The information will appear in the list at Interface Indicates the interface from which storm
the bottom of the screen. control is enabled.
The bottom portion of the IP Access List screen displays the • Port Select the port from the drop-down menu.
current IP access list, where each entry consists of an IP
Address and Wildcard Mask. To delete an entry from the Broadcast Control Select the checkbox to apply
list, select it and click Delete. Broadcast control on the selected interface. Broadcast
control limits the amount of Broadcast packet types to be
Click Save Settings to apply the changes, or Cancel forwarded. The default is not selected (disabled).
Mode Specifies the Broadcast mode currently enabled
on the device. The possible values are:
• Multicast & Broadcast Counts Broadcast and
Multicast traffic together.
• Broadcast Only Counts only Broadcast traffic.
Rate Threshold The maximum rate (packets per second)
at which unknown packets are forwarded. The ranges are
70 kbps to 100 Mbps for FE ports, and 3.5 to 100 Mbps
for GE ports. The default value is 3500 kbps.
The Update button adds the Storm Control settings to the
Storm Control table at the bottom of the screen.

Security > RADIUS Source IP Address Defines the source IP address that is
used for communication with RADIUS servers.
The RADIUS screen is used to configure a Remote
Authorization Dial-In User Service (RADIUS) server for user Usage Type Specifies the RADIUS server authentication
authentication. type. The default value is Login. The possible field values
are:
• Login Indicates that the RADIUS server is used for
authenticating user name and passwords.
• 802.1X Indicates that the RADIUS server is used for
802.1X authentication.
• All Indicates that the RADIUS server is used for
authenticating user name and passwords, and 802.1X
port authentication.
Click Add to List to add the RADIUS configuration to the
RADIUS table at the bottom of the screen.
Click Save Settings to save the changes, or Cancel
Security > RADIUS
RADIUS servers provide additional security for networks

by providing a centralized authentication method for web
access. Up to eight RADIUS servers can be configured. The
Switch attempts authentication using the listed sequence
of servers. The process ends when a server either approves
or denies access to a user.
IP Address Enter the IP address of the authentication
server.
Priority The server priority. The possible values are 0
to 65535, where 0 is the highest priority. This priority
determines the order in which RADIUS servers are queried
when more than one RADIUS server is configured. The
default priority is 0.
Authentication Port Enter the authentication port. The
authentication port is used to verify the RADIUS server
authentication. The default value is 1812.
Number of Retries Defines the number of transmitted
requests sent to RADIUS server before a failure occurs. The
possible values are 1 to 10. The default is 3.
Timeout for Reply Defines the amount of the time in
seconds the device waits for an answer from the RADIUS
server before retrying the query, or switching to the next
server. The possible values are 1 to 30. The default is 3.
Dead Time Defines the amount of time (minutes) that a
RADIUS server is bypassed for service requests. The range
is 0 to 2000. The default is 0 minutes.
Key String Defines the default key string used to
authenticate and encrypt all RADIUS communications
between the device and the RADIUS server. This key must
match the RADIUS encryption.

QoS • DSCP Setting

• Basic Mode
Network traffic is usually unpredictable, and the only
basic assurance that can be offered is best effort traffic
delivery. To overcome this challenge, Quality of Service
QoS > CoS Settings
(QoS) is applied throughout the network. This ensures that The CoS Settings screen contains fields for enabling or
network traffic is prioritized according to specified criteria, disabling CoS. This screen contains two sections, CoS
and that specific traffic receives preferential treatment. Settings and CoS Default.
QoS in the network optimizes network performance and
entails two basic facilities:
Classifying incoming traffic into handling classes, based
on an attribute, including:
• The ingress interface
• Packet content
• A combination of these attributes
Providing various mechanisms for determining the
allocation of network resources to different handling
classes, including:
• The assignment of network traffic to a particular
hardware queue
QoS > CoS Settings
• The assignment of internal resources
• Traffic shaping CoS Settings
The terms Class of Service (CoS) and QoS are used in the QoS Mode Indicates if QoS is enabled. The possible
following context: values are:
• CoS provides varying Layer 2 traffic services. CoS • Disable Disables QoS.
refers to classifying traffic into traffic classes, where
each class is handled as an aggregate whole, with no • Basic Enables QoS. This is the default value.
per-flow settings. CoS is usually related to the 802.1p Class of Service Specifies the CoS priority tag values,
service that classifies flows according to their Layer 2 where 0 is the lowest and 7 is the highest.
priority, as set in the VLAN header.
Queue Defines the traffic forwarding queue to which the
• QoS refers to Layer 2 traffic and above. QoS handles CoS priority is mapped. Four traffic priority queues are
per-flow settings, even within a single traffic class. supported.
The QoS facility involves the following elements: Click Restore Defaults to restore the device factory
• Traffic Classification—Classifies each incoming packet defaults for mapping CoS values to a forwarding queue.
as belonging to a given traffic class, based on the
CoS Default
packet contents and/or the context.
• Assignment to Hardware Queues—Assigns incoming Interface The interface to which the CoS configuration
packets to forwarding queues. Packets are sent to applies.
a particular queue for handling as a function of the Default CoS Determines the default CoS value for
traffic class to which they belong, as defined by the incoming packets for which a VLAN tag is not defined. The
classification mechanism. possible field values are 0-7. The default CoS is 0.
• Traffic Class-Handling Attributes—Applies QoS/CoS LAG The LAG to which the port belongs, if relevant. If the
mechanisms to different classes, including Bandwidth port is a member of a LAG, the LAG settings override the
Management. port settings.
The QoS configuration options are as follows: Click Save Settings to save the changes, or Cancel
• CoS Settings Changes to cancel the changes.
• Queue Settings

QoS > Queue Settings DSCP Indicates the DSCP value in the incoming packet.
Select a DSCP value from the drop-down menu to map
The Queue Settings screen contains fields for defining the that value to the associated queue. You can select the
QoS queue forwarding types. DSCP value for the High, Medium, and Normal priority
queues. The DSCP values for the Low priority queue are
selected automatically based on the other DSCP values.
Queue The queue (1-4) to which the DSCP value is being
mapped.
QoS > Basic Mode
QoS > Queue Settings
Strict Priority Indicates that traffic scheduling for the

selected queue is based strictly on the queue priority.
WRR Indicates that traffic scheduling for the selected
queue is based strictly on the WRR.
Queue Displays the queue (1-4) for which the queue
settings are displayed.
WRR Weight Displays the WRR weights to queues. QoS > Basic Mode
% of WRR Bandwidth Displays the percentage of The Basic Mode screen contains the following fields:
bandwidth assigned to the queue. These values are fixed
and cannot be modified. Trust Mode Displays the trust mode. If a packet’s CoS
tag and DSCP tag are mapped to different queues, the
Click Save Settings to save the changes, or Cancel Trust Mode determines the queue to which the packet is
Changes to cancel the changes. assigned. Possible values are:
QoS > DSCP Settings • CoS Sets trust mode to CoS on the device. The CoS
mapping determines the packet queue
The DSCP Settings screen allows you to map Differentiated
Services Code Point (DSCP) values to specific queues. • DSCP Sets trust mode to DSCP on the device. The
DSCP mapping determines the packet queue.
QoS > DSCP Settings

Spanning Tree waits between configuration messages. The default is 2

seconds. The range is 1 to 10 seconds.
Spanning Tree Protocol (STP) provides tree topography for
Root Forward delay (sec) The device forward delay time.
any arrangement of bridges. STP also provides one path
The Forward Delay Time indicates the amount of time in
between end stations on a network, eliminating loops.
seconds a bridge remains in a listening and learning state
Loops occur when alternate routes exist between hosts. before forwarding packets. The default is 15 seconds. The
Loops in an extended network can cause bridges to range is 4 to 30 seconds.
forward traffic indefinitely, resulting in increased traffic
Topology Changes Counts The total amount of STP
and reducing network efficiency.
state changes that have occurred.
The Switch supports the Classic STP version of STP, which
Last Topology Change The elapsed time since the bridge
provides a single path between end stations, avoiding
was initialized or reset, and the last topographic change
and eliminating loops.
occurred. The time is displayed in a day hour minute
second format, for example, 2 days 5 hours 10 minutes
Spanning Tree > STP Status and 4 seconds.
The STP Status screen displays the STP status on the Switch.
This information is read-only and cannot be modified. Spanning Tree > Global STP
The Global STP screen contains global parameters for STP
on the Switch.
Spanning Tree > STP Status
Spanning Tree State Indicates whether STP is enabled

on the device. Spanning Tree > Global STP
Spanning Tree Mode The STP mode by which STP is Global Setting
enabled on the device.
Spanning Tree State Select Enable or Disable from the
Bridge ID The Bridge priority and MAC address.
drop-down menu to enable or disable STP on the Switch.
Designated Root The ID of the bridge with the lowest The default is Enable.
path cost to the instance ID.
BPDU Handling Determines how BPDU packets are
Root Port The port number that offers the lowest cost managed when STP is disabled on the port or Switch.
path from this bridge to the Root Bridge. It is significant BPDUs are used to transmit spanning tree information.
when the Bridge is not the Root. The default is 0. The possible values are:
Root Path Cost The cost of the path from this bridge to • Filtering Filters BPDU packets when spanning tree is
the root. disabled on an interface. This is the default value.
Root Maximum Age (sec) The device Maximum Age • Flooding Floods BPDU packets when spanning tree is
Time, which indicates the amount of time in seconds a disabled on an interface.
bridge waits before sending configuration messages. The
Path Cost Default Values The method used to assign
default is 20 seconds. The range is 6 to 40 seconds.
default path costs to STP ports. The possible values are:
Root Hello Time (sec) The device Hello Time. The Hello
• Short Specifies a range of 1-65,535 for port path costs.
Time indicates the amount of time in seconds a root bridge
This is the default value.

Long Specifies a range of 1-200,000,000 for port path Enable STP Select this to enable STP on the port. The
costs. The default path costs assigned to an interface default is Enabled.
varies according to the selected method.
Port Fast Indicates if Fast Link is enabled on the port.
Bridge Settings If Fast Link mode is enabled for a port, the Port State
is automatically placed in the Forwarding state when
Priority Specifies the bridge priority value. When the port link is up. Fast Link optimizes the STP protocol
switches or bridges are running STP, each is assigned a convergence. STP convergence can take 30-60 seconds in
priority. After exchanging BPDUs, the device with the large networks. The possible values are Enable, Auto, and
lowest priority value becomes the Root Bridge. The default Disable. The default is Disable.
value is 32768. The value must be a multiple of 4096. For
Port State Displays the current STP state of a port. If
example, 4096, 8192, 12288, etc. The range is 0 to 65535.
enabled, the port state determines what forwarding
Hello Time Specifies the device Hello Time. The Hello action is taken on traffic. Possible port states are:
Time indicates the amount of time in seconds a root bridge
• Disabled STP is currently disabled on the port. The
waits between configuration messages. The default is 2
port forwards traffic while learning MAC addresses.
seconds. The range is 1 to 10 seconds.
• Blocking The port is currently blocked and cannot
Max Age Specifies the device Maximum Age Time. The
forward traffic or learn MAC addresses.
Maximum Age Time is the amount of time in seconds that
a bridge waits before sending configuration messages. • Listening The port is in Listening mode. The port
The default is 20 seconds. The range is 6 to 40 seconds. cannot forward traffic nor can it learn MAC addresses.
Forward Delay Specifies the device forward delay time. • Learning The port is in Learning mode. The port
The Forward Delay Time indicates the amount of time in cannot forward traffic, but can learn new MAC
seconds a bridge remains in a listening and learning state addresses.
before forwarding packets. The default is 15 seconds. The • Forwarding The port is in Forwarding mode. The port
range is 4 to 30 seconds. can forward traffic and learn new MAC addresses.
Click Save Settings to save the changes, or Cancel Speed Displays the speed at which the port is operating.
Path Cost Indicates the port contribution to the root path
Spanning Tree > STP Port Settings cost. The path cost is adjusted to a higher or lower value,
and is used to forward traffic when a path being rerouted.
The STP Port Settings screen allows network administrators The default value is 2000000 for a 10M port, 200000 for a
to assign STP settings to specific interfaces. 100M port, and 20000 for a 1G port or a LAG.
Default Path Cost When selected the default path cost is
implemented. The default is unselected.
Priority Priority value of the port. This value influences
the port choice when a bridge has two ports connected in
a loop. The range of values is 0 -240. The default is 128.
Designated Bridge ID Displays the bridge priority and
the MAC Address of the designated bridge.
Designated Port ID Displays the selected port’s priority
and interface.
Designated Cost Displays the cost of the port
participating in the STP topology. Ports with a lower cost
are less likely to be blocked if STP detects loops.
Forward Transitions Displays the number of times the
port has changed from the Blocking state to Forwarding
state.
Spanning Tree > STP Port Settings
Click Update to update the screen with your changes.
Interface Indicates the port or LAG on which STP is
enabled. Select either Port (default) or LAG, then select
the interface from the drop-down menu.

Multicast Auto Learn Select this option to enable Auto Learn on the
device. If Auto Learn is enabled, the device automatically
Multicast configuration options include IGMP Snooping, learns where other Multicast groups are located. The
Bridge Multicast, and Bridge Multicast Forward All. default is enabled (option is selected).
Host Timeout Indicates the amount of time host waits to
Multicast > IGMP Snooping receive a message before timing out. The default time is
260 seconds.
MRouter Timeout Indicates the amount of the time the
Multicast router waits to receive a message before it times
out. The default value is 300 seconds.
Leave Timeout Indicates the amount of time the host
waits, after requesting to leave the IGMP group and not
receiving a Join message from another station, before
timing out. If a Leave Timeout occurs, the switch notifies
the Multicast device to stop sending traffic The Leave
Timeout value is either user-defined, or an immediate
leave value. The default timeout is 10 seconds.
Click Update to update the screen with your changes.
Multicast > IGMP Snooping Click Save Settings to save the changes, or Cancel
When IGMP Snooping is enabled globally, all IGMP packets
are forwarded to the CPU. The CPU analyzes the incoming Multicast > Bridge Multicast
packets and determines:
The Bridge Multicast screen displays the ports and LAGs
• Which ports want to join which Multicast groups attached to the Multicast service group in the Ports and
• Which ports have Multicast routers generating IGMP LAGs tables. The Port and LAG tables also reflect the
queries manner in which the port or LAGs joined the Multicast
group.
• Which routing protocols are forwarding packets and
Multicast traffic
Ports requesting to join a specific Multicast group issue an
IGMP report, specifying that Multicast group is accepting
members. This results in the creation of the Multicast
filtering database.
The Bridge Multicast Forward All screen contains two
sections, IGMP Global and VLAN IGMP Settings. These
sections and the fields they contain are described below.
IGMP Global
Enable IGMP Snooping Select this option to enable
IGMP Snooping on the device. IGMP Snooping can be
enabled only if Bridge Multicast Filtering is enabled. The Multicast > Bridge Multicast
default is disabled (option not selected).
Ports can be added either to existing groups or to new
VLAN IGMP Settings Multicast service groups. The Bridge Multicast screen
VLAN ID Select the VLAN ID from the drop-down menu. permits new Multicast service groups to be created. The
Bridge Multicast screen also assigns ports to a specific
IGMP Status Select this option to enable IGMP snooping Multicast service address group.
on the VLAN. Default is disabled (option not selected).
The Bridge Multicast screen contains the following fields:
VLAN ID Identifies a VLAN to be configured to a Multicast
service.

Bridge Multicast Address Identifies the Multicast group Interface Interfaces with the following configuration
MAC address/IP address. options:
Bridge IP Multicast Displays the port that can be added • Static The port is user-defined.
to a Multicast service.
• Dynamic The port is configured dynamically.
Interface, Gigabit, LAG Lists switch interfaces and LAGs
• None The port is not configured for Multicast service.
that can be added to a Multicast service. The configuration
options are as follows: Gigabit Gigabit ports with the following configuration
options:
• Static Indicates the port is user-defined.
• Static The Gigabit port is user-defined.
• Dynamic Indicates the port is configured
dynamically. • Dynamic The Gigabit port is configured dynamically.
• Forbidden Forbidden ports are not included the • None The Gigabit port is not configured for Multicast
Multicast group, even if IGMP snooping designated service.
the port to join a Multicast group. LAG LAGs with the following configuration options:
• None The port is not configured for Multicast service. • Static The LAG is user-defined.
Click Add to List to add the configured static multicast • Dynamic The LAG is configured dynamically.
address to the table at the bottom of the screen.
• None The LAG is not configured for Multicast service.
Click Show All to display all multicast addresses on all
VLANs in the table at the bottom of the screen. Click Save Settings to save the changes, or Cancel
Multicast > Bridge Multicast Forward All

The Bridge Multicast Forward All screen contains fields for
attaching ports or LAGs to a device that is attached to a
neighboring Multicast router or switch.
Multicast > Bridge Multicast Forward All
Once IGMP Snooping is enabled, Multicast packets are

forwarded to the appropriate port or VLAN.
The Bridge Multicast Forward All screen contains the
following fields:
VLAN ID Displays the VLAN for which Multicast
parameters are displayed.

Admin Add to List/Update This button changes depending

on the function you are performing. When you create a
The Admin tab provides access to system administration new user name it becomes Add to List; when you edit an
settings and tools. It includes the following screens: existing password or user name, it becomes Update. For
detailed information on its use, refer to the “Local Users
Admin > User Authentication Table” section below.
The User Authentication screen is used to modify user Local Users Table
account information. You can modify the password or
user name for an existing account, or create additional The Local Users Table at the bottom of the screen lists all
accounts. existing user names (for security purposes, passwords are
not displayed). You use this table to edit or delete existing
user names and/or passwords, as described below.
Create a new user name

Make sure no entry is selected in the Local Users Table. If
one is selected, click Cancel. Enter the new user name in
the User Name field, and the password in the Password and
Confirm Password fields. Then click Add to List to add a
new entry to the Local Users Table.
Change a password
Highlight the associated user name in the Local Users
Table. The User Name, Password, and Confirm Password
fields will then be populated for editing. Enter the new
Admin > User Authentication password in the Password field, then enter it again in the
Confirm Password Field. Then click Update to save the
User Authentication changes to the Local Users Table.
Authentication Type Defines the user authentication Change a user name
methods. Combinations of all the authentication methods
can be selected. The possible field values are: Highlight the user name in the Local Users Table. The User
Name, Password, and Confirm Password fields will then be
• Local Authenticates the user at the device level.
populated for editing. Modify the user name in the User
The device checks the user name and password for Name field, then click Update to update the entry in the
authentication. Local Users Table.
• RADIUS Authenticates the user at the RADIUS server.
Delete a user name
• None Assigns no authentication method to the
authentication profile. Select the user name from the table, then click Delete.
If you accidentally select the wrong entry in the table, click
Local User Edit Cancel to unselect the highlighted user name.
User Name Displays the user name. Click Save Settings to save the changes, or Cancel
Password The password for the specified User Name. For Changes to cancel the changes.
security purposes, the password is not displayed; instead,
a“*” is displayed for each character. The password must be
between 1 and 159 characters in length.
Confirm Password Confirms the password when you
change an existing password or create a new one (for
a new User Name). The password entered into this field
must be exactly the same as the password entered in the
Password field.

Admin > Static Address Admin > Dynamic Address
Admin > Static Address Admin > Dynamic Address
The Static Address screen lets you assign a static address The Dynamic Address Table contains MAC addresses
to a specific interface on the Switch. A static address is learned by monitoring the source address on inbound
bound to its assigned interface and cannot be moved. If traffic. When the destination address of inbound traffic is
a static address is seen on an interface to which it is not found in the table, packets intended for that address are
assigned, the address is ignored and is not written to the forwarded directly to the associated port. Otherwise, the
address table. traffic is flooded to all ports.
A list of all static addresses on the Switch is displayed at The Dynamic Address screen lets you query the table to find
the bottom of the Static Address screen. The top section specific dynamic MAC addresses, or display MAC addresses
of the screen contains the following fields that you use to associated with a specific interface or VLAN. Query criteria
create static address entries. include interface type, MAC address, VLAN, and table sort
key. You can also set the Dynamic MAC Address Table’s
Interface The interface that is associated with the static
address aging parameter or clear the table.
address. Select Port or LAG, then select the desired
interface from the accompanying drop-down menu. Address Aging Specifies the amount of time (in seconds)
that a MAC address remains in the Dynamic MAC Address
MAC Address This is the physical address that is being
table before it times out, if no traffic from the source is
mapped to the specified interface.
detected. The default value is 300 seconds.
VLAN ID The VLAN ID number (1-4093) of the configured
Clear Table If checked, this clears the MAC Address
VLAN that is associated with the specified interface. If you
table.
use this field the VLAN Name field is disabled.
VLAN Name The name of the VLAN associated with the Query
specified interface. If you use this field, the VLAN ID field
Interface Use this to query the table for a specific port or
is disabled.
LAG. Select Port or LAG and select the interface from the
Status The static address type. The possible values are:: drop-down menu.
• Permanent (default) Keep the entry permanently. MAC Address Use this to query the table for a specific
• Delete on Reset Delete the entry when the Switch is
MAC address. Enter the MAC address in the field.
reset. VLAN ID Use this to query the table for a specific VLAN ID.
• Delete on Timeout Delete the entry when a timeout
Enter the VLAN ID in the field.
occurs. The default timeout period is 300 seconds. Address Table Sort Key Specifies how the search results
• Secure The entry is defined for locked ports.
will be sorted—by Address, VLAN, or Interface.
After you have entered the information listed above, click Specify the search criteria (Interface, MAC Address, or
Add to List. The static address will then appear in the list VLAN) and the sort method for the search results, then
of static addresses. To delete a static MAC address from click Query to display the dynamic addresses matching
the list, select the entry in the list, then click Remove. the search criteria.

Admin > Port Mirroring Admin > Save Configuration

Port mirroring monitors and mirrors network traffic by
forwarding copies of incoming and outgoing packets
from one port to a monitoring port. Port mirroring can be
used as diagnostic tool and/or a debugging feature. Port
mirroring also enables switch performance monitoring.
Network administrators configure port mirroring by
selecting a specific port to copy all packets, and different
ports from which the packets are copied.
Admin > Save Configuration
The Save Configuration screen allows you to upload Switch

configuration files to a TFTP server, or to download saved
Switch configuration files from a TFTP server or from your
computer via the HTTP interface.
Via TFTP Select this to upload to or download from a
TFTP server. When you select this option, the following
fields are displayed.
Admin > Port Mirroring
• UPGRADE Select this option to restore the Switch
Set the following attributes for port mirroring using the configuration from the file located on a TFTP server.
Port Mirroring screen.
• TFTP Server Enter the TFTP Server IP Address that
Target Port The port that will mirror the traffic on the contains the source file to download.
source port.
• File Name Enter the name of the configuration file
Source Port The port whose traffic will be monitored. on the TFTP Server.
Type Allows you to select which traffic to mirror to the • BACKUP To back up the Switch configuration to a
target port; receive, transmit, or both. TFTP server, enter the TFTP server address.
• RxOnly Mirror only received traffic. This is the default • TFTP Server Enter the TFTP Server IP Address to
value. which the configuration file will be saved.
• TxOnly Mirror only transmitted traffic. • File Name Enter the name of the configuration
file. The default is StartupCfg.cfg.
• Both Mirror both received and transmitted traffic.
Via HTTP Select this to download a configuration file to
Specify the source port, the traffic type to be mirrored, and
the Switch from your computer using the HTTP interface.
the target port, then click Add to List. The mirror session
(HTTP only supports the upgrade operation. You cannot
is displayed in the text box.
back up the configuration file using HTTP.) When you
select this option, the following field is displayed.
• Source File Enter the name and path of the file or
click Browse to locate the configuration file.
Click Save Settings to begin the download or upload.
After you have downloaded the configuration file to the
Switch during an upgrade, the configuration file’s settings
will not take effect until the system is rebooted.

Admin > Firmware Upgrade Admin > Reboot

The Reboot screen is used to reset the Switch. The current
configuration settings are automatically saved before the
Switch is rebooted.
Admin > Firmware Upgrade
The Firmware Upgrade screen allows you to download

firmware upgrade files from a TFTP server, or from your
computer via the HTTP interface. Admin > Reboot
Via TFTP Select this to download from or upload to a Click the Reboot button, then click OK to confirm.
TFTP server. When you select this option, the following
fields are displayed. Admin > Factory Default
• UPGRADE Select this option to upgrade the switch The Factory Default screen allows network managers to
from a file located on a TFTP server. reset the Switch to the factory defaults shipped with the
• File Type Select the type of file to download, switch. Restoring factory defaults results in erasing the
either Software Image or Boot Code. configuration file.
• TFTP Server Enter the TFTP Server IP Address that

NOTE: Restoring the factory defaults will erase
contains the source file to upgrade from.
all of your current configuration settings. Before
• File Name Enter the name of the upgrade file on you restore the factory defaults, you can save a
the TFTP Server. backup of your current configuration settings
from the Admin > Save Configuration screen..
• BACKUP To back up the firmware to a TFTP server,
enter the TFTP server address.
• TFTP Server Enter the TFTP Server IP Address to
which the firmware file will be saved.
• File Name Enter the name of the file.
Via HTTP Select this to download an upgrade file using
the HTTP interface. When you select this option, the
following field is displayed:
• Source File Enter the name and path of the file or
click Browse to locate the upgrade file.
Click Save Settings to begin the download or upload.
Admin > Factory Default
Click Reset Default, then click OK to confirm and restart

the Switch.

Admin > Logging Admin > Memory Logs

The Memory Log screen contains all system logs in
chronological order that are saved in RAM (Cache).
Log Index Displays the log number.
Log Time Displays the date and time at which the log
was generated.
Severity Displays the log severity.
Description Displays the log message text.
Admin > Logging
The System Logs allow you to view device events in real

time, and recording the events for later usage. System
Logs record and manage events and report errors or
informational messages.
Event messages have a unique format, as per the
SYSLOG protocols recommended message format for
all error reporting. For example, Syslog and local device
reporting messages are assigned a severity code, and Admin > Memory Logs
include a message mnemonic, which identifies the source
application generating the message. It allows messages Admin > Flash Logs
to be filtered based on their urgency or relevancy. Each
message severity determines the set of event logging The Flash Log screen contains information about log
devices that are sent per each event logging. entries saved to the Log File in flash memory, including
the time the log was generated, the log severity, and
Enable Logging If this option is selected, device global
a description of the log message. The Message Log is
logs for Cache, File, and Server Logs are enabled. The
available after reboot.
default is enabled.
Log Index Displays the log number.
• Emergency The system is not functioning.
Log Time Displays the date and time at which the log
• Alert The system needs immediate attention.
was generated.
• Critical The system is in a critical state.
Severity Displays the log severity.
• Error A system error has occurred.
Description Displays the log message text.
• Warning A system warning has occurred.
• Notice The system is functioning properly, but system
notice has occurred.
• Informational Provides device information.
• Debug Provides detailed information about the
log. If a Debug error occurs, contact Customer Tech
Support.
If you enable Logging, use the checkboxes to set the level
of event messages to be logged to RAM (Memory Logs)
and flash memory (Flash Logs), then click Save Settings.
Admin > Flash Logs

Logout
The Logout tab is used to terminate the login session.
When you select the Logout tab, the following dialog box
asks you to verify if you want to log out.
Logout Verification
If you select Yes, a confirmation screen appears.
Confirmation of Successful Logout

Appendix A About Gigabit Ethernet and Fiber Optic Cabling
Appendix A:
About Gigabit Ethernet
and Fiber Optic Cabling
Gigabit Ethernet
Gigabit Ethernet runs at speeds of 1Gbps (Gigabit per
second), ten times faster than 100Mbps Fast Ethernet, but
it still integrates seamlessly with 100Mbps Fast Ethernet
hardware. Users can connect Gigabit Ethernet hardware
with either fiber optic cabling or copper Category
5e cabling, with fiber optics more suited for network
backbones. As the Gigabit standard gradually integrates
into existing networks, current computer applications will
enjoy faster access time for network data, hardware, and
Internet connections.
Fiber Optic Cabling

Fiber optic cabling is made from flexible, optically efficient
strands of glass and coated with a layer of rubber tubing,
fiber optics use photons of light instead of electrons to
send and receive data. Although fiber is physically capable
of carrying terabits of data per second, the signaling
hardware currently on the market can handle no more
than a few gigabits of data per second.
Fiber cables come with two main connector types. The
most commonly used fiber optic cable is multi-mode
fiber cable (MMF), with a 62,5 micron fiber optic core.
Single‑mode fiber cabling is somewhat more efficient
than multi-mode but far more expensive, due to its smaller
optic core that helps retain the intensity of traveling light
signals. A fiber connection always require two fiber cables:
one transmits data, and the other receives it.
Each fiber optic cable is tipped with a connector that fits
into a fiber port on a network adapter, hub, or switch.
In the USA, most cables use a square SC connector that
slides and locks into place when plugged into a port or
connected to another cable. In Europe, the round ST
connector is more prevalent.
For Gigabit Ethernet, you must use the Linksys MGBT1,
MGBSX1, or MGBLH1 miniGBIC modules with the Linksys
Gigabit Switches. The MGBSX1 and the MGBLH1 require
fiber cabling with LC connectors, and the MGBT1 requires
a Category 5e Ethernet cable with an RJ-45 connector.
For Fast Ethernet, you must use the MFEFX1 (100BASE-FX)
or MFELX1 (100BASE-LX) SFP transceivers.

Appendix B Glossary
Appendix B: Baud Indicates the number of signaling elements

transmitted each second.
Glossary Best Effort Indicates that traffic is assigned to the lowest
priority queue, and packet delivery is not guaranteed.
This glossary contains some basic networking terms you Bit A binary digit.
may come across when using this product.
Boot To start a device and cause it to start executing
instructions.
WEB: For additional terms, please visit the Browser An application program that provides a way to
glossary at www.linksys.com/glossary
look at and interact with all the information on the World
Wide Web.
Access Mode Specifies the method by which user access
Bridge A device that connect two networks. Bridges are
is granted to the system.
hardware specific, however they are protocol independent.
Access Point A device that allows wireless-equipped Bridges operate at Layer 1 and Layer 2 levels.
computers and other devices to communicate with a
Broadcast Domain Devices sets that receive broadcast
wired network. Also used to expand the range of a wireless
frames originating from any device within a designated
network.
set. Routers bind Broadcast domains, because routers do
Access Profiles Allows network managers to define not forward broadcast frames.
profiles and rules for accessing the device. Access to
Broadcast Storm An excessive amount of broadcast
management functions can be limited to user groups,
messages simultaneously transmitted across a network
which are defined by the following criteria:
by a single port. Forwarded message responses are
• Ingress interfaces heaped onto the network, overloading network resources
or causing the network to time out.
• Source IP address and/or Source IP subnets.
ACE Filters in Access Control Lists (ACL) that determine Burst A packet transmission at faster than normal rates.
which network traffic is forwarded. An ACE is based on the Bursts are limited in time and only occur under specific
following criteria: conditions.
Burst Size Indicates the burst size transmitted at a faster
• Protocol
than normal rate.
• Protocol ID
Byte A unit of data that is usually eight bits long
• Source Port
Cable Modem A device that connects a computer to the
• Destination Port cable television network, which in turn connects to the
Internet.
• Wildcard Mask
CBS (Committed Burst Size) Indicates the maximum
• Source IP Address
number of data bits transmitted within a specific time
• Destination IP Address interval.
ACL (Access Control List) Access Control Lists are CIR (Committed Information Rate) The data rate is
used to grant, deny, or limit access devices, features, or averaged over a minimum time increment.
applications.
Class Maps An aspect of Quality of Service system that is
Auto-negotiation Allows 10/100 Mbps or 10/100/1000 comprised of an IP ACL and/or a MAC ACL. Class maps are
Mbps Ethernet ports to automatically establish the configured to match packet criteria, and are matched to
optimal duplex mode, flow control, and speed. packets in a first-fit fashion.
Back Pressure A mechanism used with Half Duplex mode Combo Ports A single logical port with two physical
that enables a port not to receive a message. connections, including an RJ-45 connection and a SFP
Bandwidth The transmission capacity of a given device connection.
or network. Communities Specifies a group of users which retain the
Bandwidth Assignments Indicates the amount of same system access rights.
bandwidth assigned to a specific application, user, and/or
interface.

Appendix B Glossary
CoS (Class of Service) The 802.1p priority scheme. CoS Full Duplex The ability of a networking device to receive
provides a method for tagging packets with priority and transmit data simultaneously.
information. A CoS value between 0-7 is added to the
GARP (General Attributes Registration
Layer II header of packets, where zero is the lowest priority
Protocol) Registers client stations into a multicast
and seven is the highest.
domain.
DDNS (Dynamic Domain Name System) Allows the
Gateway A device that interconnects networks with
hosting of a website, FTP server, or e-mail server with a
different, incompatible communications protocols.
fixed domain name (e.g., www.xyz.com) and a dynamic IP
address. GBIC (GigaBit Interface Converter) A hardware module
used to attach network devices to fiber-based transmission
Default Gateway A device that forwards Internet traffic
systems. GBIC converts the serial electrical signals to serial
from your local area network.
optical signals and vice versa.
DHCP (Dynamic Host Configuration Protocol) A
GVRP (GARP VLAN Registration Protocol) Registers
networking protocol that allows administrators to assign
client stations into a VLANs.
temporary IP addresses to network computers by “leasing”
an IP address to a user for a limited amount of time, instead Half Duplex Data transmission that can occur in two
of assigning permanent IP addresses. directions over a single line, but only one direction at a
time.
DHCP Clients An Internet host using DHCP to obtain
configuration parameters, such as a network address. HTTP (HyperText Transport Protocol) The
communications protocol used to connect to servers on
DHCP Server An Internet host that returns configuration
the World Wide Web.
parameters to DHCP clients.
HTTPS (HyperText Transport Protocol Secure) An
DNS (Domain Name Server) The IP address of your ISP’s
extension to the standard HTTP protocol that provides
server, which translates the names of websites into IP
confidentiality by encrypting the traffic from the website.
addresses.
By default this protocol uses TCP port 443.
Domain A specific name for a network of computers.
ICMP (Internet Control Message Protocol) Allows the
Download To receive a file transmitted over a network. gateway or destination host to communicate with the
source host. For example, to report a processing error.
DSL (Digital Subscriber Line) An always-on broadband
connection over traditional phone lines. IGMP (Internet Group Management Protocol) Allows
hosts to notify their local switch or router that they want
DSCP (DiffServ Code Point) Provides a method of
to receive transmissions assigned to a specific multicast
tagging IP packets with QoS priority information.
group.
Dynamic IP Address A temporary IP address assigned by
IP (Internet Protocol) A protocol used to send data over
a DHCP server.
a network.
EIGRP (Enhanced Interior Gateway Routing
IP Address The address used to identify a computer or
Protocol) Provides fast convergence, support for variable-
device on a network.
length subnet mask, and supports multiple network layer
protocols. IPCONFIG A Windows 2000 and XP utility that displays
the IP address for a particular networking device.
Encryption Encoding data transmitted in a network.
IPSec (Internet Protocol Security) A VPN protocol used
Ethernet IEEE standard network protocol that specifies
to implement secure exchange of packets at the IP layer.
how data is placed on and retrieved from a common
transmission medium. ISP (Internet Service Provider) A company that provides
access to the Internet.
Firmware The programming code that runs a networking
device. Jumbo Frames Enable transporting identical data in
fewer frames. Jumbo Frames reduce overhead, lower
Flow Control Enables lower speed devices to
processing time, and ensure fewer interrupts.
communicate with higher speed devices. This is
implemented by the higher speed device refraining from LAG (Link Aggregated Group) Aggregates ports or
sending packets. VLANs into a single virtual port or VLAN.
FTP (File Transfer Protocol) A protocol used to transfer LAN The computers and networking products that make
files over a TCP/IP network. up your local network.

Appendix B Glossary
MAC (Media Access Control) Address The unique RADIUS (Remote Authentication Dial-In User
address that a manufacturer assigns to each networking Service) A protocol that uses an authentication server to
device. control network access.
Mask A filter that includes or excludes certain values, for RJ-45 (Registered Jack-45) An Ethernet connector that
example parts of an IP address. holds up to eight wires.
Mbps (MegaBits Per Second) One million bits per RMON (Remote Monitoring) Provides network
second; a unit of measurement for data transmission. information to be collected from a single workstation.
MD5 (Message Digest 5) An algorithm that produces a Router A networking device that connects multiple
128-bit hash. MD5 is a variation of MD4, and increases MD4 networks together.
security. MD5 verifies the integrity of the communication
RSTP (Rapid Spanning Tree Protocol) Detects and uses
and authenticates the origin of the communication.
network topologies that allow a faster convergence of the
MDI (Media Dependent Interface) A cable used for end spanning tree, without creating forwarding loops.
stations.
Server Any computer whose function in a network is to
MDIX (Media Dependent Interface with Crossover) A provide user access to files, printing, communications,
cable used for hubs and switches. and other services.
MIB (Management Information Base) MIBs contain SMTP (Simple Mail Transfer Protocol) The standard e-
information describing specific aspects of network mail protocol on the Internet.
components.
SNMP (Simple Network Management Protocol) A
Multicast Transmits copies of a single packet to multiple widely used network monitoring and control protocol.
ports.
SSH Secure Shell. A utility that uses strong authentication
Network A series of computers or devices connected for and secure communications to log in to another computer
the purpose of data sharing, storage, and/or transmission over a network.
between users.
SSL (Secure Socket Layer) Encryption technology for
NMS (Network Management System) An interface that the Internet used to provide secure transactions, such as
provides a method of managing a system. the transmission of credit card numbers for e-commerce.
OID (Object Identifier) Used by SNMP to identify Static IP Address A fixed address assigned to a computer
managed objects. In the SNMP Manager/Agent network or device that is connected to a network.
management paradigm, each managed object must have
STP (Spanning Tree Protocol) Prevents loops in network
an OID to identify it.
traffic. The Spanning Tree Protocol (STP) provides tree
Packet A unit of data sent over a network. topography for any arrangement of bridges. STP provides
one path between end stations on a network, eliminating
Ping (Packet INternet Groper) An Internet utility used
loops.
to determine whether a particular IP address is online.
Subnet (Sub-network) Subnets are portions of a
Policing Determines if traffic levels are within a specified
network that share a common address component. In
profile. Policing manages the maximum traffic rate used
TCP/IP networks, devices that share a prefix are part of
to send or receive packets on an interface.
the same subnet. For example, all devices with a prefix of
Port The connection point on a computer or networking 157.100.100.100 are part of the same subnet.
device used for plugging in cables or adapters.
Subnet Mask An address code that determines the size
Port Mirroring Monitors and mirrors network traffic by of the network.
forwarding copies of incoming and outgoing packets
Switch Filters and forwards packets between LAN
from one port to a monitoring port.
segments. Switches support any packet protocol type.
Power over Ethernet (PoE) A technology enabling an
TACACS+ (Terminal Access Controller Access Control
Ethernet network cable to deliver both data and power.
System Plus) Proprietary Cisco enhancement to Terminal
QoS (Quality of Service) Provides policies that contain Access Controller Access Control System (TACACS). Provides
sets of filters (rules). QoS allows network managers additional support for authentication, authorization, and
to decide how and what network traffic is forwarded accounting.
according to priorities, application types, and source and
destination addresses.

Appendix B Glossary
TCP (Transmission Control Protocol) A network protocol

for transmitting data that requires acknowledgement
from the recipient of data sent.
TCP/IP (Transmission Control Protocol/Internet
Protocol) A set of instructions PCs use to communicate
over a network.
Telnet A user command and TCP/IP protocol used for
accessing remote PCs.
TFTP (Trivial File Transfer Protocol) A version of the
TCP/IP FTP protocol that has no directory or password
capability.
Throughput The amount of data moved successfully
from one node to another in a given time period.
Trunking Link Aggregation. Optimizes port usage by
linking a group of ports together to form a single trunk
(aggregated groups).
TX Rate Transmission Rate.
UDP (User Data Protocol) Communication protocol that
transmits packets but does not guarantee their delivery.
Upgrade To replace existing software or firmware with a
newer version.
Upload To transmit a file over a network.
URL (Uniform Resource Locator) The address of a file
located on the Internet.
VLAN (Virtual Local Area Networks) Logical subgroups
that constitute a Local Area Network (LAN). This is done in
software rather than defining a hardware solution.
WAN (Wide Area Network) Networks that cover a large
geographical area.
Wildcard Mask Specifies which IP address bits are
used, and which bits are ignored. A wild card mask
of 255.255.255.255 indicates that no bit is important.
A wildcard of 0.0.0.0 indicates that all the bits are
important.
For example, if the destination IP address is 149.36.184.198
and the wildcard mask is 255.36.184.00, the first two bits
of the IP address are used, while the last two bits are
ignored.

Appendix C Specifications
Appendix C:
Specifications
SLM2024/SLM2048 Security
802.1X - RADIUS Authentication.
Specifications MD5 Encryption
Ports 24 or 48 RJ-45 connectors for Port Security - MAC-based Filtering
10BASE-T/100BASE-TX/1000BASE-T Management Access Control
including 2 combo ports with Availability
miniGBIC/SFP slots
Link Aggregation Link Aggregation using
Auto MDI/MDI-X
IEEE 802.3ad LACP
Auto-negotiate/Manual setting
Up to 4 groups with up to 8 ports
Buttons Reset per group
Cabling Type UTP CAT 5e or better for 1000BASE-T Storm Control Broadcast and Multicast
LEDs System, Gigabit Link/Act and Speed Spanning Tree IEEE 802.1D Spanning Tree
Performance and Port Fast
Switching Capacity SLM2024: IGMP Snooping IGMP (v1/v2) Snooping provides
48 Gbps non-blocking for fast client joins and leaves of
multicast streams and limits
SLM2048:
bandwidth-intensive video traffic
96 Gbps non-blocking
to only the requestors.
Forwarding Rate SLM2024: Supports 32 Multicast Groups
35,71 Mpps wire-speed performance
QoS
SLM2048:
71,42 Mpps wire-speed performance Priority levels 4 Hardware queues
Scheduling Priority Queueing and
Layer 2 Weighted Round Robin (WRR)
MAC Table Size 8K
Class of Service Port-based
Number of VLANs 128 active VLANs (4096 range) 802.1p VLAN priority-based
VLAN Port-based and 802.1Q Tag-based IPv4/v6 IP DSCP based
VLANs Standards
Management VLAN
802.3 10BASE-T Ethernet,
HOL Blocking Head of line blocking prevention 802.3u 100BASE-TX Fast Ethernet,
Management 802.3ab 1000BASE-T Gigabit Ethernet,
802.3z Gigabit Ethernet,
Web User Interface Built-in Web UI for easy browser-
802.3x Flow Control,
based configuration (HTTP)
802.3ad LACP,
Firmware Upgrade Web Browser upgrade (HTTP) 802.1D STP,
and TFTP upgrade 802.1Q/p VLAN,
Port Mirroring Traffic on a port can be mirrored 802.1X Port Access Authentication
to another port for analysis
Environmental
with a network analyzer
Dimensions SLM2024: 440 x 43 x 257 mm
Other Management DHCP/BootP Client
(W x H x D) SLM2048: 440 x 43 x 345 mm
System Log
Configuration upload and backup Unit Weight SLM2024: 3,1 kg
via HTTP or TFTP SLM2048: 4,6 kg
Power Internal Power, 100-240V
Certification FCC Part15 Class A, CE Class A,
UL, cUL, CE mark, CB

Operating Temp. 0 to 50ºC Port Mirroring Traffic on a port can be mirrored

Storage Temp. 0 to 70ºC to another port for analysis
with a network analyzer
Operating Humidity 10 to 90% Noncondensing
Other Management DHCP/BootP Client
Storage Humidity 10 to 90% Noncondensing System Log
Configuration upload and
SLM224G/SLM248G/SLM224P/SLM248P backup via HTTP or TFTP
Specifications Security
Ports 24 or 48 RJ-45 connectors for 802.1X - RADIUS Authentication.
10BASE-T/100BASE-TX, MD5 Encryption
2 combo ports with RJ-45 Port Security - MAC-based Filtering
connectors for 10BASE-T/ Management Access Control
100BASE-TX/1000BASE-T and
miniGBIC/SFP slots
Availability
Auto MDI/MDI-X Link Aggregation Link Aggregation using
Auto-negotiate/Manual setting IEEE 802.3ad LACP
Up to 4 groups with up to 8 ports
Buttons Reset
per group
Cabling Type UTP CAT 5 or better for
Storm Control Broadcast and Multicast
10BASE-T/100BASE-TX,
UTP CAT 5e or better for 1000BASE-T Spanning Tree IEEE 802.1D Spanning Tree
and Port Fast
LEDs SLM224G and SLM248G:
System IGMP Snooping IGMP (v1/v2) Snooping provides
10/100 Link/Act and Speed for fast client joins and leaves of
Gigabit Link/Act and Speed multicast streams and limits
bandwidth-intensive video traffic
SLM224P and SLM248P:
to only the requestors.
System
Supports 32 Multicast Groups
10/100 Link/Act and PoE or Speed
Gigabit Link/Act and Speed QoS
Performance Priority levels 4 Hardware queues
Switching Capacity SLM224G and SLM224P: Scheduling Priority Queueing and
8,8 Gbps non-blocking Weighted Round Robin (WRR)
SLM248G and SLM248P: Class of Service Port-based
13,6 Gbps non-blocking 802.1p VLAN priority-based
IPv4/v6 IP DSCP based
Forwarding Rate SLM224G and SLM224P:
6,55 Mpps wire-speed performance Standards
SLM248G and SLM248P: 802.3 10BASE-T Ethernet,
10,12 Mpps wire-speed performance 802.3u 100BASE-TX Fast Ethernet,
802.3ab 1000BASE-T Gigabit Ethernet,
Layer 2
802.3z Gigabit Ethernet,
MAC Table Size 8K 802.3x Flow Control,
Number of VLANs 128 active VLANs (4096 range) 802.3ad LACP,
VLAN Port-based and 802.1Q Tag-based 802.1D STP,
VLANs 802.1Q/p VLAN,
Management VLAN 802.1X Port Access Authentication
HOL Blocking Head of line blocking prevention Environmental
Management Dimensions SLM224G, SLM224P, SLM248G:
(W x H x D) 440 x 43 x 257 mm
Web User Interface Built-in Web UI for easy browser-
based configuration (HTTP) SLM248G: 440 x 43 x 345 mm
Firmware Upgrade Web Browser upgrade (HTTP) Unit Weight SLM224G: 2,9 kg
and TFTP upgrade SLM248G: 3,1 kg

SLM224P: 3,3 kg
SLM248P: 4,6 kg
Power Internal Power, 100-240V
Certification FCC Part15 Class A, CE Class A,
UL, cUL, CE mark, CB
Operating Temp. 0 to 50ºC
Storage Temp. 0 to 70ºC
Operating Humidity 10 to 90% Noncondensing
Storage Humidity 10 to 90% Noncondensing

Appendix D Warranty Information
Appendix D: TO THE EXTENT NOT PROHIBITED BY LAW, IN NO EVENT

WILL LINKSYS BE LIABLE FOR ANY LOST DATA, REVENUE
Warranty Information OR PROFIT, OR FOR SPECIAL, INDIRECT, CONSEQUENTIAL,
INCIDENTAL OR PUNITIVE DAMAGES, REGARDLESS OF THE
Linksys warrants to You that, for a period of five years THEORY OF LIABILITY (INCLUDING NEGLIGENCE), ARISING
(the “Warranty Period”), your Linksys Product will be OUT OF OR RELATED TO THE USE OF OR INABILITY TO
substantially free of defects in materials and workmanship USE THE PRODUCT (INCLUDING ANY SOFTWARE), EVEN
under normal use. Your exclusive remedy and Linksys’ IF LINKSYS HAS BEEN ADVISED OF THE POSSIBILITY OF
entire liability under this warranty will be for Linksys at SUCH DAMAGES. IN NO EVENT WILL LINKSYS’ LIABILITY
its option to repair or replace the Product or refund Your EXCEED THE AMOUNT PAID BY YOU FOR THE PRODUCT.
purchase price less any rebates. This limited warranty The foregoing limitations will apply even if any warranty or
extends only to the original purchaser. remedy provided under this Agreement fails of its essential
purpose. Some jurisdictions do not allow the exclusion or
If the Product proves defective during the Warranty limitation of incidental or consequential damages, so the
Period call Linksys Technical Support in order to obtain above limitation or exclusion may not apply to You.
a Return Authorization Number, if applicable. BE SURE
TO HAVE YOUR PROOF OF PURCHASE ON HAND WHEN This Warranty is valid and may be processed only in
CALLING. If You are requested to return the Product, mark the country of purchase.
the Return Authorization Number clearly on the outside Please direct all inquiries to: Linksys, P.O. Box 18558, Irvine,
of the package and include a copy of your original proof CA 92623.
of purchase. RETURN REQUESTS CANNOT BE PROCESSED
WITHOUT PROOF OF PURCHASE. You are responsible
for shipping defective Products to Linksys. Linksys pays
for UPS Ground shipping from Linksys back to You only.
Customers located outside of the United States of America
and Canada are responsible for all shipping and handling
charges.
ALL IMPLIED WARRANTIES AND CONDITIONS OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE ARE LIMITED TO THE DURATION OF THE
WARRANTY PERIOD. ALL OTHER EXPRESS OR IMPLIED
CONDITIONS, REPRESENTATIONS AND WARRANTIES,
INCLUDING ANY IMPLIED WARRANTY OF NON-
INFRINGEMENT, ARE DISCLAIMED. Some jurisdictions do
not allow limitations on how long an implied warranty
lasts, so the above limitation may not apply to You. This
warranty gives You specific legal rights, and You may also
have other rights which vary by jurisdiction.
This warranty does not apply if the Product (a) has been
altered, except by Linksys, (b) has not been installed,
operated, repaired, or maintained in accordance with
instructions supplied by Linksys, or (c) has been subjected
to abnormal physical or electrical stress, misuse,
negligence, or accident. In addition, due to the continual
development of new techniques for intruding upon and
attacking networks, Linksys does not warrant that the
Product will be free of vulnerability to intrusion or attack.

Appendix E Regulatory Information
Appendix E: Industry Canada Statement

Regulatory Information This Class A digital apparatus complies with Canadian
ICES-003.
Operation is subject to the following two conditions:
FCC Statement 1. This device may not cause interference and
This equipment has been tested and complies with 2. This device must accept any interference, including
the specifications for a Class A digital device, pursuant interference that may cause undesired operation of
to Part 15 of the FCC Rules. Operation is subject to the the device.
following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any
interference received, including interference that may
Avis d’ Industrie Canada
cause undesired operation. These limits are designed Cet appareil numérique de la classe A est conforme à la
to provide reasonable protection against harmful norme NMB-003 d’ Industrie Canada.
interference when equipment is operated in a commercial
Le fonctionnement est soumis aux conditions suivantes :
environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and 1. Ce périphérique ne doit pas causer d’interférences;
used in accordance with the instruction manual, may
2. Ce périphérique doit accepter toutes les interférences
cause harmful interference to radio communications.
reçues, y compris celles qui risquent d’entraîner un
Operation of this equipment in a residential area is likely to fonctionnement indésirable.
cause harmful interference in which case the user will be
required to correct the interference at his own expense. EC Declaration of Conformity (Europe)
WARNING: You are cautioned that changes or In compliance with the EMC Directive 89/336/EEC, Low
modifications not expressly approved by the Voltage Directive 73/23/EEC, and Amendment Directive
party responsible for compliance could void 93/68/EEC, this product meets the requirements of the
your authority to operate the equipment. following standards:
• EN55022 Emission
Safety Notices • EN55024 Immunity
• EN60950 Safety
• Caution: To reduce the risk of fire, use only No.26 AWG
or larger telecommunication line cord.
• Do not use this product near water, for example, in a
wet basement or near a swimming pool.
• Avoid using this product during an electrical storm.
There may be a remote risk of electric shock from
lightning.

User Information for Consumer Products Ceština (Czech) - Informace o ochraně životního
prostředí pro zákazníky v zemích Evropské unie
Covered by EU Directive 2002/96/EC on Evropská směrnice 2002/96/ES zakazuje, aby zařízení označené
tímto symbolem na produktu anebo na obalu bylo likvidováno
Waste Electric and Electronic Equipment s netříděným komunálním odpadem. Tento symbol udává,
(WEEE) že daný produkt musí být likvidován odděleně od běžného
komunálního odpadu. Odpovídáte za likvidaci tohoto produktu
This document contains important information for users a dalších elektrických a elektronických zařízení prostřednictvím
with regards to the proper disposal and recycling of určených sběrných míst stanovených vládou nebo místními
úřady. Správná likvidace a recyklace pomáhá předcházet
Linksys products. Consumers are required to comply with
potenciálním negativním dopadům na životní prostředí a lidské
this notice for all electronic products bearing the following zdraví. Podrobnější informace o likvidaci starého vybavení si
symbol: laskavě vyžádejte od místních úřadů, podniku zabývajícího se
likvidací komunálních odpadů nebo obchodu, kde jste produkt
zakoupili.
Dansk (Danish) - Miljøinformation for kunder i EU

EU-direktiv 2002/96/EF kræver, at udstyr der bærer dette symbol
på produktet og/eller emballagen ikke må bortskaffes som
usorteret kommunalt affald. Symbolet betyder, at dette produkt
skal bortskaffes adskilt fra det almindelige husholdningsaffald.
Det er dit ansvar at bortskaffe dette og andet elektrisk og
English - Environmental Information for Customers in elektronisk udstyr via bestemte indsamlingssteder udpeget
the European Union af staten eller de lokale myndigheder. Korrekt bortskaffelse
European Directive 2002/96/EC requires that the equipment og genvinding vil hjælpe med til at undgå mulige skader for
bearing this symbol on the product and/or its packaging must miljøet og menneskers sundhed. Kontakt venligst de lokale
not be disposed of with unsorted municipal waste. The symbol myndigheder, renovationstjenesten eller den butik, hvor du
indicates that this product should be disposed of separately har købt produktet, angående mere detaljeret information om
from regular household waste streams. It is your responsibility to bortskaffelse af dit gamle udstyr.
dispose of this and other electric and electronic equipment via
designated collection facilities appointed by the government or
local authorities. Correct disposal and recycling will help prevent Deutsch (German) - Umweltinformation für Kunden
potential negative consequences to the environment and innerhalb der Europäischen Union
human health. For more detailed information about the disposal Die Europäische Richtlinie 2002/96/EC verlangt, dass technische
of your old equipment, please contact your local authorities, Ausrüstung, die direkt am Gerät und/oder an der Verpackung mit
waste disposal service, or the shop where you purchased the diesem Symbol versehen ist , nicht zusammen mit unsortiertem
product. Gemeindeabfall entsorgt werden darf. Das Symbol weist darauf
hin, dass das Produkt von regulärem Haushaltmüll getrennt
entsorgt werden sollte. Es liegt in Ihrer Verantwortung, dieses
Български (Bulgarian) - Информация относно Gerät und andere elektrische und elektronische Geräte über
опазването на околната среда за потребители в die dafür zuständigen und von der Regierung oder örtlichen
Европейския съюз Behörden dazu bestimmten Sammelstellen zu entsorgen.
Европейска директива 2002/96/EC изисква уредите, носещи Ordnungsgemäßes Entsorgen und Recyceln trägt dazu bei,
този символ върху изделието и/или опаковката му, да не potentielle negative Folgen für Umwelt und die menschliche
се изхвърля т с несортирани битови отпадъци. Символът Gesundheit zu vermeiden. Wenn Sie weitere Informationen zur
обозначава, че изделието трябва да се изхвърля отделно от Entsorgung Ihrer Altgeräte benötigen, wenden Sie sich bitte an
сметосъбирането на обикновените битови отпадъци. Ваша die örtlichen Behörden oder städtischen Entsorgungsdienste
е отговорността този и другите електрически и електронни oder an den Händler, bei dem Sie das Produkt erworben haben.
уреди да се изхвърлят в предварително определени от
държавните или общински органи специализирани пунктове
за събиране. Правилното изхвърляне и рециклиране
ще спомогнат да се предотвратят евентуални вредни за
околната среда и здравето на населението последствия. За
по-подробна информация относно изхвърлянето на вашите
стари уреди се обърнете към местните власти, службите за
сметосъбиране или магазина, от който сте закупили уреда.

Eesti (Estonian) - Keskkonnaalane informatsioon Français (French) - Informations environnementales

Euroopa Liidus asuvatele klientidele pour les clients de l’Union européenne
Euroopa Liidu direktiivi 2002/96/EÜ nõuete kohaselt on La directive européenne 2002/96/CE exige que l’équipement
seadmeid, millel on tootel või pakendil käesolev sümbol , sur lequel est apposé ce symbole sur le produit et/ou son
keelatud kõrvaldada koos sorteerimata olmejäätmetega. See emballage ne soit pas jeté avec les autres ordures ménagères. Ce
sümbol näitab, et toode tuleks kõrvaldada eraldi tavalistest symbole indique que le produit doit être éliminé dans un circuit
olmejäätmevoogudest. Olete kohustatud kõrvaldama käesoleva distinct de celui pour les déchets des ménages. Il est de votre
ja ka muud elektri- ja elektroonikaseadmed riigi või kohalike responsabilité de jeter ce matériel ainsi que tout autre matériel
ametiasutuste poolt ette nähtud kogumispunktide kaudu. électrique ou électronique par les moyens de collecte indiqués
Seadmete korrektne kõrvaldamine ja ringlussevõtt aitab vältida par le gouvernement et les pouvoirs publics des collectivités
võimalikke negatiivseid tagajärgi keskkonnale ning inimeste territoriales. L’élimination et le recyclage en bonne et due forme
tervisele. Vanade seadmete kõrvaldamise kohta täpsema ont pour but de lutter contre l’impact néfaste potentiel de ce
informatsiooni saamiseks võtke palun ühendust kohalike type de produits sur l’environnement et la santé publique. Pour
ametiasutustega, jäätmekäitlusfirmaga või kauplusega, kust te plus d’informations sur le mode d’élimination de votre ancien
toote ostsite. équipement, veuillez prendre contact avec les pouvoirs publics
locaux, le service de traitement des déchets, ou l’endroit où vous
avez acheté le produit.
Español (Spanish) - Información medioambiental para
clientes de la Unión Europea
La Directiva 2002/96/CE de la UE exige que los equipos que Italiano (Italian) - Informazioni relative all’ambiente
lleven este símbolo en el propio aparato y/o en su embalaje per i clienti residenti nell’Unione Europea
no deben eliminarse junto con otros residuos urbanos no La direttiva europea 2002/96/EC richiede che le apparecchiature
seleccionados. El símbolo indica que el producto en cuestión contrassegnate con questo simbolo sul prodotto e/o
debe separarse de los residuos domésticos convencionales con sull’imballaggio non siano smaltite insieme ai rifiuti urbani
vistas a su eliminación. Es responsabilidad suya desechar este y non differenziati. Il simbolo indica che questo prodotto non
cualesquiera otros aparatos eléctricos y electrónicos a través de deve essere smaltito insieme ai normali rifiuti domestici. È
los puntos de recogida que ponen a su disposición el gobierno y responsabilità del proprietario smaltire sia questi prodotti sia
las autoridades locales. Al desechar y reciclar correctamente estos le altre apparecchiature elettriche ed elettroniche mediante
aparatos estará contribuyendo a evitar posibles consecuencias le specifiche strutture di raccolta indicate dal governo o dagli
negativas para el medio ambiente y la salud de las personas. Si enti pubblici locali. Il corretto smaltimento ed il riciclaggio
desea obtener información más detallada sobre la eliminación aiuteranno a prevenire conseguenze potenzialmente negative
segura de su aparato usado, consulte a las autoridades locales, per l’ambiente e per la salute dell’essere umano. Per ricevere
al servicio de recogida y eliminación de residuos de su zona o informazioni più dettagliate circa lo smaltimento delle vecchie
pregunte en la tienda donde adquirió el producto. apparecchiature in Vostro possesso, Vi invitiamo a contattare gli
enti pubblici di competenza, il servizio di smaltimento rifiuti o il
negozio nel quale avete acquistato il prodotto.
ξλληνικά (Greek) - Στοιχεία περιβαλλοντικής
προστασίας για πελάτες εντός της Ευρωπαϊκής
Ένωσης Latviešu valoda (Latvian) - Ekoloģiska informācija
Η Κοινοτική Οδηγία 2002/96/EC απαιτεί ότι ο εξοπλισμός ο οποίος klientiem Eiropas Savienības jurisdikcijā
φέρει αυτό το σύμβολο στο προϊόν και/ή στη συσκευασία Direktīvā 2002/96/EK ir prasība, ka aprīkojumu, kam pievienota
του δεν πρέπει να απορρίπτεται μαζί με τα μικτά κοινοτικά zīme uz paša izstrādājuma vai uz tā iesaiņojuma, nedrīkst
απορρίμματα. Το σύμβολο υποδεικνύει ότι αυτό το προϊόν θα izmest nešķirotā veidā kopā ar komunālajiem atkritumiem
πρέπει να απορρίπτεται ξεχωριστά από τα συνήθη οικιακά (tiem, ko rada vietēji iedzīvotāji un uzņēmumi). Šī zīme nozīmē
απορρίμματα. Είστε υπεύθυνος για την απόρριψη του παρόντος to, ka šī ierīce ir jāizmet atkritumos tā, lai tā nenonāktu kopā ar
και άλλου ηλεκτρικού και ηλεκτρονικού εξοπλισμού μέσω των parastiem mājsaimniecības atkritumiem. Jūsu pienākums ir šo
καθορισμένων εγκαταστάσεων συγκέντρωσης απορριμμάτων οι un citas elektriskas un elektroniskas ierīces izmest atkritumos,
οποίες παρέχονται από το κράτος ή τις αρμόδιες τοπικές αρχές. izmantojot īpašus atkritumu savākšanas veidus un līdzekļus, ko
Η σωστή απόρριψη και ανακύκλωση συμβάλλει στην πρόληψη nodrošina valsts un pašvaldību iestādes. Ja izmešana atkritumos
πιθανών αρνητικών συνεπειών για το περιβάλλον και την υγεία. un pārstrāde tiek veikta pareizi, tad mazinās iespējamais
Για περισσότερες πληροφορίες σχετικά με την απόρριψη του kaitējums dabai un cilvēku veselībai. Sīkākas ziņas par
παλιού σας εξοπλισμού, παρακαλώ επικοινωνήστε με τις τοπικές novecojuša aprīkojuma izmešanu atkritumos jūs varat saņemt
αρχές, τις υπηρεσίες απόρριψης ή το κατάστημα από το οποίο vietējā pašvaldībā, atkritumu savākšanas dienestā, kā arī veikalā,
αγοράσατε το προϊόν. kur iegādājāties šo izstrādājumu.

Lietuvškai (Lithuanian) - Aplinkosaugos informacija, Nederlands (Dutch) - Milieu-informatie voor klanten

skirta Europos Sąjungos vartotojams in de Europese Unie
Europos direktyva 2002/96/EC numato, kad įrangos, kuri ir De Europese Richtlijn 2002/96/EC schrijft voor dat apparatuur die
kurios pakuotė yra pažymėta šiuo simboliu (įveskite simbolį), is voorzien van dit symbool op het product of de verpakking,
negalima šalinti kartu su nerūšiuotomis komunalinėmis niet mag worden ingezameld met niet-gescheiden huishoudelijk
atliekomis. Šis simbolis rodo, kad gaminį reikia šalinti atskirai afval. Dit symbool geeft aan dat het product apart moet worden
nuo bendro buitinių atliekų srauto. Jūs privalote užtikrinti, kad ingezameld. U bent zelf verantwoordelijk voor de vernietiging
ši ir kita elektros ar elektroninė įranga būtų šalinama per tam van deze en andere elektrische en elektronische apparatuur via de
tikras nacionalinės ar vietinės valdžios nustatytas atliekų rinkimo daarvoor door de landelijke of plaatselijke overheid aangewezen
sistemas. Tinkamai šalinant ir perdirbant atliekas, bus išvengta inzamelingskanalen. De juiste vernietiging en recycling van
galimos žalos aplinkai ir žmonių sveikatai. Daugiau informacijos deze apparatuur voorkomt mogelijke negatieve gevolgen voor
apie jūsų senos įrangos šalinimą gali pateikti vietinės valdžios het milieu en de gezondheid. Voor meer informatie over het
institucijos, atliekų šalinimo tarnybos arba parduotuvės, kuriose vernietigen van uw oude apparatuur neemt u contact op met
įsigijote tą gaminį. de plaatselijke autoriteiten of afvalverwerkingsdienst, of met de
winkel waar u het product hebt aangeschaft.
Malti (Maltese) - Informazzjoni Ambjentali għal Klijenti

fl-Unjoni Ewropea Norsk (Norwegian) - Miljøinformasjon for kunder i EU
Id-Direttiva Ewropea 2002/96/KE titlob li t-tagħmir li jkun fih is- EU-direktiv 2002/96/EF krever at utstyr med følgende symbol
simbolu fuq il-prodott u/jew fuq l-ippakkjar ma jistax jintrema avbildet på produktet og/eller pakningen, ikke må kastes
ma’ skart muniċipali li ma ġiex isseparat. Is-simbolu jindika sammen med usortert avfall. Symbolet indikerer at dette
li dan il-prodott għandu jintrema separatament minn ma’ l- produktet skal håndteres atskilt fra ordinær avfallsinnsamling
iskart domestiku regolari. Hija responsabbiltà tiegħek li tarmi for husholdningsavfall. Det er ditt ansvar å kvitte deg med
dan it-tagħmir u kull tagħmir ieħor ta’ l-elettriku u elettroniku dette produktet og annet elektrisk og elektronisk avfall via egne
permezz ta’ faċilitajiet ta’ ġbir appuntati apposta mill-gvern jew innsamlingsordninger slik myndighetene eller kommunene
mill-awtoritajiet lokali. Ir-rimi b’mod korrett u r-riċiklaġġ jgħin bestemmer. Korrekt avfallshåndtering og gjenvinning vil
jipprevjeni konsegwenzi negattivi potenzjali għall-ambjent u være med på å forhindre mulige negative konsekvenser for
għas-saħħa tal-bniedem. Għal aktar informazzjoni dettaljata miljø og helse. For nærmere informasjon om håndtering av
dwar ir-rimi tat-tagħmir antik tiegħek, jekk jogħġbok ikkuntattja det kasserte utstyret ditt, kan du ta kontakt med kommunen,
lill-awtoritajiet lokali tiegħek, is-servizzi għar-rimi ta’ l-iskart, jew en innsamlingsstasjon for avfall eller butikken der du kjøpte
il-ħanut minn fejn xtrajt il-prodott. produktet.
Magyar (Hungarian) - Környezetvédelmi információ az Polski (Polish) - Informacja dla klientów w Unii
európai uniós vásárlók számára Europejskiej o przepisach dotyczących ochrony
A 2002/96/EC számú európai uniós irányelv megkívánja, hogy środowiska
azokat a termékeket, amelyeken, és/vagy amelyek csomagolásán Dyrektywa Europejska 2002/96/EC wymaga, aby sprzęt
az alábbi címke megjelenik, tilos a többi szelektálatlan lakossági oznaczony symbolem znajdującym się na produkcie i/lub jego
hulladékkal együtt kidobni. A címke azt jelöli, hogy az adott opakowaniu nie był wyrzucany razem z innymi niesortowanymi
termék kidobásakor a szokványos háztartási hulladékelszállítási odpadami komunalnymi. Symbol ten wskazuje, że produkt
rendszerektõl elkülönített eljárást kell alkalmazni. Az Ön nie powinien być usuwany razem ze zwykłymi odpadami z
felelõssége, hogy ezt, és más elektromos és elektronikus gospodarstw domowych. Na Państwu spoczywa obowiązek
berendezéseit a kormányzati vagy a helyi hatóságok által wyrzucania tego i innych urządzeń elektrycznych oraz
kijelölt gyűjtõredszereken keresztül számolja fel. A megfelelõ elektronicznych w punktach odbioru wyznaczonych przez władze
hulladékfeldolgozás segít a környezetre és az emberi egészségre krajowe lub lokalne. Pozbywanie się sprzętu we właściwy sposób
potenciálisan ártalmas negatív hatások megelõzésében. Ha i jego recykling pomogą zapobiec potencjalnie negatywnym
elavult berendezéseinek felszámolásához további részletes konsekwencjom dla środowiska i zdrowia ludzkiego. W celu
információra van szüksége, kérjük, lépjen kapcsolatba a helyi uzyskania szczegółowych informacji o usuwaniu starego sprzętu,
hatóságokkal, a hulladékfeldolgozási szolgálattal, vagy azzal prosimy zwrócić się do lokalnych władz, służb oczyszczania
üzlettel, ahol a terméket vásárolta. miasta lub sklepu, w którym produkt został nabyty.

Português (Portuguese) - Informação ambiental para Slovenčina (Slovene) - Okoljske informacije za stranke
clientes da União Europeia v Evropski uniji
A Directiva Europeia 2002/96/CE exige que o equipamento Evropska direktiva 2002/96/EC prepoveduje odlaganje opreme,
que exibe este símbolo no produto e/ou na sua embalagem označene s tem simbolom – na izdelku in/ali na embalaži – med
não seja eliminado junto com os resíduos municipais não običajne, nerazvrščene odpadke. Ta simbol opozarja, da je treba
separados. O símbolo indica que este produto deve ser izdelek odvreči ločeno od preostalih gospodinjskih odpadkov.
eliminado separadamente dos resíduos domésticos regulares. Vaša odgovornost je, da to in preostalo električno in elektronsko
É da sua responsabilidade eliminar este e qualquer outro opremo odnesete na posebna zbirališča, ki jih določijo
equipamento eléctrico e electrónico através das instalações državne ustanove ali lokalna uprava. S pravilnim odlaganjem
de recolha designadas pelas autoridades governamentais ou in recikliranjem boste preprečili morebitne škodljive vplive na
locais. A eliminação e reciclagem correctas ajudarão a prevenir okolje in zdravje ljudi. Če želite izvedeti več o odlaganju stare
as consequências negativas para o ambiente e para a saúde opreme, se obrnite na lokalno upravo, odpad ali trgovino, kjer
humana. Para obter informações mais detalhadas sobre a ste izdelek kupili.
forma de eliminar o seu equipamento antigo, contacte as
autoridades locais, os serviços de eliminação de resíduos ou o
estabelecimento comercial onde adquiriu o produto. Suomi (Finnish) - Ympäristöä koskevia tietoja EU-
alueen asiakkaille
EU-direktiivi 2002/96/EY edellyttää, että jos laitteistossa on tämä
Română (Romanian) - Informaţii de mediu pentru symboli itse tuotteessa ja/tai sen pakkauksessa, laitteistoa
clienţii din Uniunea Europeană ei saa hävittää lajittelemattoman yhdyskuntajätteen mukana.
Directiva europeană 2002/96/CE impune ca echipamentele care Symboli merkitsee sitä, että tämä tuote on hävitettävä erillään
prezintă acest simbol pe produs şi/sau pe ambalajul acestuia să tavallisesta kotitalousjätteestä. Sinun vastuullasi on hävittää
nu fie casate împreună cu gunoiul menajer municipal. Simbolul tämä elektroniikkatuote ja muut vastaavat elektroniikkatuotteet
indică faptul că acest produs trebuie să fie casat separat de viemällä tuote tai tuotteet viranomaisten määräämään
gunoiul menajer obişnuit. Este responsabilitatea dvs. să casaţi keräyspisteeseen. Laitteiston oikea hävittäminen estää
acest produs şi alte echipamente electrice şi electronice prin mahdolliset kielteiset vaikutukset ympäristöön ja ihmisten
intermediul unităţilor de colectare special desemnate de guvern terveyteen. Lisätietoja vanhan laitteiston oikeasta hävitystavasta
sau de autorităţile locale. Casarea şi reciclarea corecte vor ajuta saa paikallisilta viranomaisilta, jätteenhävityspalvelusta tai siitä
la prevenirea potenţialelor consecinţe negative asupra sănătăţii myymälästä, josta ostit tuotteen.
mediului şi a oamenilor. Pentru mai multe informaţii detaliate
cu privire la casarea acestui echipament vechi, contactaţi
autorităţile locale, serviciul de salubrizare sau magazinul de la Svenska (Swedish) - Miljöinformation för kunder i
care aţi achiziţionat produsul. Europeiska unionen
Det europeiska direktivet 2002/96/EC kräver att utrustning med
denna symbol på produkten och/eller förpackningen inte får
Slovenčina (Slovak) - Informácie o ochrane životného kastas med osorterat kommunalt avfall. Symbolen visar att denna
prostredia pre zákazníkov v Európskej únii produkt bör kastas efter att den avskiljts från vanligt hushållsavfall.
Podľa európskej smernice 2002/96/ES zariadenie s týmto Det faller på ditt ansvar att kasta denna och annan elektrisk och
symbolom na produkte a/alebo jeho balení nesmie byť elektronisk utrustning på fastställda insamlingsplatser utsedda
likvidované spolu s netriedeným komunálnym odpadom. av regeringen eller lokala myndigheter. Korrekt kassering och
Symbol znamená, že produkt by sa mal likvidovať oddelene återvinning skyddar mot eventuella negativa konsekvenser
od bežného odpadu z domácností. Je vašou povinnosťou för miljön och personhälsa. För mer detaljerad information om
likvidovať toto i ostatné elektrické a elektronické zariadenia kassering av din gamla utrustning kontaktar du dina lokala
prostredníctvom špecializovaných zberných zariadení určených myndigheter, avfallshanteringen eller butiken där du köpte
vládou alebo miestnymi orgánmi. Správna likvidácia a recyklácia produkten.
pomôže zabrániť prípadným negatívnym dopadom na životné
prostredie a zdravie ľudí. Ak máte záujem o podrobnejšie
informácie o likvidácii starého zariadenia, obráťte sa, prosím, na WEB: For additional information, please visit
miestne orgány, organizácie zaoberajúce sa likvidáciou odpadov www.linksys.com/international
alebo obchod, v ktorom ste si produkt zakúpili.

Appendix F Contact Information
Appendix F: Location E-mail Address
Contact Information Spain support.es@linksys.com
If you experience problems with any Linksys product, you

Sweden support.se@linksys.com
can e-mail us at:
Europe Switzerland support.ch@linksys.com
Location E-mail Address Turkey support.tk@linksys.com
Austria support.at@linksys.com
United Kingdom support.uk@linksys.com
Belgium support.be@linksys.com
Outside of Europe
Czech Republic support.cz@linksys.com
Location E-mail Address
asiasupport@linksys.com
Denmark support.dk@linksys.com Asia Pacific
(English only)
support.portuguese@linksys.com or
Finland support.fi@linksys.com Latin America
support.spanish@linksys.com
support.mea@linksys.com
France support.fr@linksys.com Middle East & Africa
(English only)
support.ze@linksys.com
Germany support.de@linksys.com South Africa
(English only)
support.gr@linksys.com support.ae@linksys.com
Greece UAE
(English only) (English only)
Hungary support.hu@linksys.com U.S. and Canada support@linksys.com
Ireland support.ie@linksys.com
NOTE: For some countries, support may be
available only in English.
Italy support.it@linksys.com
Netherlands support.nl@linksys.com
Norway support.no@linksys.com
Poland support.pl@linksys.com
Portugal support.pt@linksys.com
Russia support.ru@linksys.com
7100910B-AI

SLM2xx Manual Switch

Uploaded by

Copyright:

Available Formats

SLM2xx Manual Switch

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

SLM2xx Manual Switch

Uploaded by

Copyright:

Available Formats

USER GUIDE

Business Series Smart

About This Guide

NOTE: This check mark indicates that there is

WARNING: This exclamation point indicates

WEB: This globe icon indicates a noteworthy

Linksys Europe www.linksys.eu

Linksys International www.linksys.com/international

Network Security www.linksys.com/security

Copyright and Trademarks

Chapter 4: Configuration Using the Web-based Utility 11

Business Series Smart Gigabit Ethernet Switch ii

Port Management > LACP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Appendix A: About Gigabit Ethernet and Fiber Optic Cabling 37

Business Series Smart Gigabit Ethernet Switch iii

Fiber Optic Cabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Appendix D: Warranty Information 45

Appendix F: Contact Information 51

Business Series Smart Gigabit Ethernet Switch iv

Chapter 1: security by keeping sensitive data separated from other

Business Series Smart Gigabit Ethernet Switch 

Chapter 2: miniGBIC (1-2) The miniGBIC (gigabit interface

Business Series Smart Gigabit Ethernet Switch 

SLM2024 miniGBIC (1-2) The miniGBIC (gigabit interface

POWER The Power port is where you connect

Business Series Smart Gigabit Ethernet Switch 

SLM248G G1-G2 The Switch is equipped with 2 auto-

POWER The Power port is where you connect

Business Series Smart Gigabit Ethernet Switch 

SLM248P G1-G2 The Switch is equipped with 2 auto-

Business Series Smart Gigabit Ethernet Switch 

SLM224G G1-G2 The Switch is equipped with 2 auto-

POWER The Power port is where you connect

Business Series Smart Gigabit Ethernet Switch 

SLM224P G1-G2 The Switch is equipped with 2 auto-

Business Series Smart Gigabit Ethernet Switch 

Chapter 3: Pre-Installation Considerations

1000BASE-T Cable Requirements

From To Maximum Distance

Business Series Smart Gigabit Ethernet Switch 

Desktop Placement To rack-mount the Switch in any standard 482,6-mm wide,

Attaching the Brackets

3. Follow the same steps to attach the other bracket to

For a 1000 Mbps device: Ethernet Ports Shared with miniGBIC Ports

IMPORTANT: Make sure you use the power

7. Power on the devices connected to the Switch. Each

Uplinking the Switch

Business Series Smart Gigabit Ethernet Switch 10

NOTE: The default IP address is 192.168.1.254.

The Login screen appears. Enter admin in the Username

NOTE: The port colors in the Summary screen

The Summary screen two sections: Device Information and

Business Series Smart Gigabit Ethernet Switch 11

NOTE: The Default Gateway cannot be

Address Mode Specifies whether IP functionality is

NOTE: The Jumbo Frame setting applies ONLY Identification

Business Series Smart Gigabit Ethernet Switch 12

IP Configuration Setup > Time

WARNING: The Management VLAN must be

IP Address Mode Specifies whether IP functionality is

Business Series Smart Gigabit Ethernet Switch

Business Series Smart Gigabit Ethernet Switch

Business Series Smart Gigabit Ethernet Switch

Business Series Smart Gigabit Ethernet Switch

Business Series Smart Gigabit Ethernet Switch

Business Series Smart Gigabit Ethernet Switch

Business Series Smart Gigabit Ethernet Switch

Business Series Smart Gigabit Ethernet Switch