R XPT PDF
R XPT PDF
R XPT PDF
R-XPT Throughbolt
Throughbolt for non-cracked concrete
Product information
Installation guide
Product information
Anchor Fixture
R-XPT-06050/10 AT-15-9327/14 6 50 10 - 7
R-XPT-06065/5 AT-15-9327/14 6 65 25 5 7
M6
R-XPT-06085/25 AT-15-9327/14 6 85 45 25 7
R-XPT-08050/5 AT-15-9327/14 8 50 5 - 9
R-XPT-08060/10 ETA-08/0339 8 60 10 - 9
R-XPT-08065/15 ETA-08/0339 8 65 15 - 9
R-XPT-08075/10 ETA-08/0339 8 75 25 10 9
R-XPT-08080/15 ETA-08/0339 8 80 30 15 9
M8
R-XPT-08085/20 ETA-08/0339 8 85 35 20 9
R-XPT-08095/30 ETA-08/0339 8 95 45 30 9
R-XPT-10065/5 ETA-08/0339 10 65 5 - 11
R-XPT-10080/10 ETA-08/0339 10 80 20 10 11
R-XPT-10085/15 ETA-08/0339 10 85 25 15 11
R-XPT-10095/25 ETA-08/0339 10 95 35 25 11
R-XPT-12080/5 ETA-08/0339 12 80 5 - 13
www.rawlplug.com 2
Mechanical Anchors
Product information
Anchor Fixture
R-XPT-20200/60 - 20 200 80 60 22
M20
R-XPT-20300/160 - 20 300 180 160 22
Installation data
Min. substrate thickness hmin,s [mm] 84 100 100 136 170 198 224
Min. substrate thickness hmin,r [mm] 80 100 100 100 130 158 194
Mechanical properties
Size M6 M8 M10 M12 M16 M20 M24
2
Nominal ultimate tensile strength - tension fuk [N/mm ] 400 400 400 400 400 480 480
Nominal yield strength - tension fyk [N/mm2] 320 320 320 320 320 384 384
Cross sectional area - tension As [mm2] 20.1 36.6 58 84.3 157 245 353
Elastic section modulus Wel [mm3] 21.2 50.3 98.2 169.6 402.1 785.4 1357.2
Characteristic bending resistance M0Rk,s [Nm] 10.9 25.9 50.7 87.5 207.5 452.4 781.7
Design bending resistance M [Nm] 8.7 20.7 40.5 70 166 361.9 625.4
www.rawlplug.com 3
Mechanical Anchors
Standard embedment depth [kN] 8.70 18.10 19.80 28.00 49.70 65.30 67.60
Reduced embedment depth [kN] 5.70 10.90 11.40 21.50 43.00 45.50 62.70
Standard embedment depth [kN] 6.00 12.20 19.20 28.00 51.50 80.90 118.60
Reduced embedment depth [kN] 6.00 12.20 19.10 28.00 51.50 94.70 118.60
CHARACTERISTIC LOAD
Standard embedment depth [kN] 6.80 12.00 12.00 25.00 40.00 40.00 50.00
Reduced embedment depth [kN] 4.50 9.00 9.00 16.00 30.00 35.00 48.90
Standard embedment depth [kN] 5.50 10.10 16.00 23.30 43.00 67.40 91.10
Reduced embedment depth [kN] 5.50 10.10 12.00 23.30 43.00 67.40 97.10
DESIGN LOAD
Standard embedment depth [kN] 3.80 6.70 6.70 13.90 22.20 22.20 27.80
Reduced embedment depth [kN] 2.50 5.00 5.00 8.90 16.70 19.40 27.20
Standard embedment depth [kN] 4.40 8.10 12.80 18.60 34.40 53.90 77.70
Reduced embedment depth [kN] 4.40 8.10 6.70 18.60 34.40 38.20 77.70
RECOMMENDED LOAD
Standard embedment depth [kN] 2.70 4.80 4.80 9.90 15.90 15.90 19.80
Reduced embedment depth [kN] 1.80 3.60 3.60 6.40 11.90 13.90 19.40
Standard embedment depth [kN] 3.10 5.80 9.10 13.30 24.60 38.50 55.50
Reduced embedment depth [kN] 3.10 5.80 4.80 13.30 24.60 27.30 55.50
www.rawlplug.com 4
Mechanical Anchors
Effective embedment depth hef [mm] 42.00 47.00 49.00 68.00 85.00 99.00 112.00
TENSION LOAD
STEEL FAILURE
Characteristic resistance NRk,s [kN] 8.10 15.80 25.20 37.30 66.10 101.00 137.20
Design resistance Ms= 1.4 NRd,s [kN] 5.79 11.29 18.00 26.64 47.21 72.14 98.00
Characteristic resistance NRk,p [kN] 6.80 12.00 12.00 25.00 40.00 40.00 50.00
Design resistance Mp= 1.8 NRd,p [kN] 3.78 6.67 6.67 13.89 22.22 22.22 27.78
Increasing factors for NRd,p - C30/37 c - 1.10 1.10 1.37 1.16 1.17 1.30 1.10
Increasing factors for NRd,p - C40/50 c - 1.21 1.21 1.74 1.33 1.34 1.59 1.21
Increasing factors for NRd,p - C50/60 c - 1.32 1.32 2.10 1.49 1.50 1.89 1.32
Spacing scr,N [mm] 126.00 141.00 147.00 204.00 255.00 297.00 336.00
Edge distance ccr,N [mm] 63.00 71.00 74.00 102.00 128.00 149.00 168.00
SHEAR LOAD
Edge distance c1 [mm] 50.00 55.00 65.00 90.00 105.00 160.00 200.00
Characteristic resistance for c1 VRk,c [kN] 6.39 7.71 10.04 16.86 22.48 41.63 58.63
Design resistance Mc= 1.8 VRd,c [kN] 3.55 4.28 5.58 9.37 12.49 23.13 32.57
STEEL FAILURE
Characteristic resistance without lever arm VRk,s [kN] 5.50 10.10 16.00 23.30 43.00 67.40 94.10
Design resistance Ms= 1.25 VRd,s [kN] 4.40 8.08 12.80 18.64 34.40 53.92 77.68
Reduction factors for edge distance <Ccr,N applicable to NRd or Nrec for non-cracked concrete from 'Basic
Performance' table
40 0,68 0,53
100 0,87 0,87 0,82 0,98 0,66 0,83 0,62 0,78 0,56
105 0,90 0,90 0,85 1,00 0,68 0,86 0,63 0,80 0,57
300 1,00
www.rawlplug.com 5
Mechanical Anchors
Increasing factors for edge distance >Cmin applicable to VRd,c for non-cracked concrete from Design Per
formance table
40 1,00 1,00
100 2,84 2,55 2,08 1,77 1,69 1,34 1,34 1,00 1,00
650 2,37
700 2,53
750 2,69
800 2,85
880 3,10
www.rawlplug.com 6
Mechanical Anchors
Reduction factors for spacing <Scr,N applicable to NRd / VRd or Nrec / Vrec for non-cracked concrete from
'Basic Performance' table
[mm] h 1.84hmin hmin h 1.84hmin hmin h 1.84hmin hmin h 1.84hmin hmin h 1.84hmin hmin h 1.84hmin hmin h 1.84hmin hmin
45 0,68 0,59
90 0,86 0,69 0,82 0,69 0,81 0,67 0,72 0,62 0,68 0,60
100 0,90 0,71 0,85 0,71 0,84 0,69 0,75 0,64 0,70 0,62
125 1,00 0,76 0,94 0,76 0,93 0,74 0,81 0,67 0,75 0,65
140 0,79 1,00 0,79 0,98 0,77 0,84 0,69 0,77 0,66 0,74 0,63
150 0,81 0,81 1,00 0,79 0,87 0,70 0,79 0,67 0,75 0,64
180 0,88 0,88 0,85 0,94 0,74 0,85 0,71 0,80 0,67 0,77 0,65
200 0,92 0,92 0,88 0,99 0,77 0,89 0,73 0,84 0,69 0,80 0,67
205 0,93 0,93 0,89 1,00 0,78 0,90 0,74 0,85 0,69 0,81 0,67
240 1,00 1,00 0,96 0,82 0,97 0,78 0,90 0,73 0,86 0,70
600 1,00
www.rawlplug.com 7
Mechanical Anchors
Effective embedment depth hef [mm] 22.00 32.00 39.00 48.00 65.00 79.00 97.00
TENSION LOAD
STEEL FAILURE
Characteristic resistance NRk,s [kN] 8.10 15.80 25.20 37.30 66.10 101.00 137.20
Design resistance Ms= 1.4 NRd,s [kN] 5.79 11.29 18.00 26.64 47.21 72.14 98.00
Characteristic resistance NRk,p [kN] 4.50 9.00 9.00 16.00 30.00 35.00 48.90
Design resistance Mp= 1.8 NRd,p [kN] 2.50 5.00 5.00 8.89 16.67 19.44 27.17
Increasing factors for NRd,p - C30/37 c - 1.25 1.25 1.36 1.20 1.12 1.18 1.25
Increasing factors for NRd,p - C40/50 c - 1.50 1.50 1.72 1.40 1.23 1.36 1.50
Increasing factors for NRd,p - C50/60 c - 1.76 1.76 2.08 1.60 1.34 1.54 1.76
Spacing scr,N [mm] 66.00 96.00 117.00 144.00 195.00 237.00 291.00
Edge distance ccr,N [mm] 33.00 48.00 59.00 72.00 98.00 119.00 146.00
SHEAR LOAD
Edge distance c1 [mm] 45.00 50.00 65.00 100.00 100.00 125.00 160.00
Characteristic resistance for c1 VRk,c [kN] 5.05 6.37 9.67 18.36 20.04 28.81 42.54
Design resistance Mc= 1.8 VRd,c [kN] 2.80 3.54 5.37 10.20 11.13 16.00 23.63
k - - - 1.00 - - 2.00 -
STEEL FAILURE
Characteristic resistance without lever arm VRk,s [kN] 5.50 10.10 16.00 23.30 43.00 67.40 97.10
Design resistance Ms= 1.25 VRd,s [kN] 4.40 8.08 12.80 18.64 34.40 53.92 77.68
Reduction factors for edge distance <Ccr,N applicable to NRd or Nrec for non-cracked concrete from 'Basic
Performance' table
40 0,87 0,64
90 0,92
240 0,94
260 1,00
www.rawlplug.com 8
Mechanical Anchors
Increasing factors for edge distance >Cmin applicable to VRd,c for non-cracked concrete from Design Per
formance table
40 1,00 1,00
600 2,78
700 3,19
800 3,60
970 4,28
www.rawlplug.com 9
Mechanical Anchors
Reduction factors for spacing <Scr,N applicable to NRd / VRd or Nrec / Vrec for non-cracked concrete from
'Basic Performance' table
[mm] h 1.84hmin hmin h 1.84hmin hmin h 1.84hmin hmin h 1.84hmin hmin h 1.84hmin hmin h 1.84hmin hmin h 1.84hmin hmin
40 0,80 0,63
125 0,89 0,89 0,81 0,93 0,75 0,82 0,67 0,76 0,65
145 0,95 0,95 0,86 1,00 0,79 0,87 0,70 0,81 0,68
160 1,00 1,00 0,90 0,82 0,91 0,72 0,84 0,70 0,77 0,65
520 1,00
R-XPT-10085/151) 10 85
www.rawlplug.com 10
Mechanical Anchors
www.rawlplug.com 11