Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 520 views

    Exp 13 Fault Analysis

    Uploaded by

    Gokul Chandrasekaran
    A power system diagram and fault analysis problem is presented. The document includes a one line diagram, system data, and asks to determine the fault current for four different types of faults at bus 3 through a 0.1 per unit fault impedance: (1) A balanced three-phase fault would result in a fault current of 1.0 per unit. (2) A single line-to-ground fault current is calculated to be 1.0/1.45 per unit. (3) A line-to-line fault current is calculated to be 1.0/0.22 per unit. (4) A double line-to-ground fault current is calculated using a MATLAB program to

    Copyright:

    © All Rights Reserved
    Download as DOC, PDF, TXT or read online from Scribd

    Exp 13 Fault Analysis

    Uploaded by

    Gokul Chandrasekaran
    520 views4 pages
    A power system diagram and fault analysis problem is presented. The document includes a one line diagram, system data, and asks to determine the fault current for four different types of faults at bus 3 through a 0.1 per unit fault impedance: (1) A balanced three-phase fault would result in a fault current of 1.0 per unit. (2) A single line-to-ground fault current is calculated to be 1.0/1.45 per unit. (3) A line-to-line fault current is calculated to be 1.0/0.22 per unit. (4) A double line-to-ground fault current is calculated using a MATLAB program to

    Original Description:

    PSS LAB

    Copyright

    © © All Rights Reserved

    Available Formats

    DOC, PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    A power system diagram and fault analysis problem is presented. The document includes a one line diagram, system data, and asks to determine the fault current for four different types of faults at bus 3 through a 0.1 per unit fault impedance: (1) A balanced three-phase fault would result in a fault current of 1.0 per unit. (2) A single line-to-ground fault current is calculated to be 1.0/1.45 per unit. (3) A line-to-line fault current is calculated to be 1.0/0.22 per unit. (4) A double line-to-ground fault current is calculated using a MATLAB program to

    Copyright:

    © All Rights Reserved
    Download as DOC, PDF, TXT or read online from Scribd
    Download as doc, pdf, or txt
    520 views4 pages

    Exp 13 Fault Analysis

    Uploaded by

    Gokul Chandrasekaran
    A power system diagram and fault analysis problem is presented. The document includes a one line diagram, system data, and asks to determine the fault current for four different types of faults at bus 3 through a 0.1 per unit fault impedance: (1) A balanced three-phase fault would result in a fault current of 1.0 per unit. (2) A single line-to-ground fault current is calculated to be 1.0/1.45 per unit. (3) A line-to-line fault current is calculated to be 1.0/0.22 per unit. (4) A double line-to-ground fault current is calculated using a MATLAB program to

    Copyright:

    © All Rights Reserved
    Download as DOC, PDF, TXT or read online from Scribd
    Download as doc, pdf, or txt
    of 4

    ---Exp 13---------FAULT ANALYSIS-----HS P 427 -------Ex10.

    5------

    PROBLEM:
    The one line diagram of a simple power system is shown in figure. The neutral of each
    generator is grounded through a current limiting reactor of 0.25/3 per unit on a
    100MVA base. The system data expressed in per unit on a common 100 MVA base is
    tabulated below. The generators are running on no load at their rated voltage and rated
    frequency with their emf in phase.
    Determine the fault current for the following faults.
    (a) A balanced three phase fault at bus 3 through a fault impedance, Zf = j0.1 per unit.
    (b) A single line to ground fault at bus3 through a fault impedance, Zf = j0.1 per unit.
    (c) A line to line fault at bus3 through a fault impedance, Zf = j0.1 per unit.
    (d) A double line to ground fault at bus3 through a fault impedance, Zf = j0.1 per unit.

    MATLAB PROGRAM:
    Z133 = j*0.22; Z033 = j*0.35; Zf = j*0.1;
    disp('(a) Balanced three-phase fault at bus 3')
    Ia3F = 1.0/(Z133+Zf)
    disp('(b) Single line-to-ground fault at bus 3')
    I03 = 1.0/(Z033 + 3*Zf + Z133 + Z133);
    I012=[I03; I03; I03]
    %sctm;
    global sctm
    a =cos(2*pi/3)+j*sin(2*pi/3);
    sctm = [1 1 1; 1 a^2 a; 1 a a^2];
    Iabc3 = sctm*I012
    disp('(c) Line-to-line fault at bus 3')
    I13 = 1.0/(Z133 + Z133 + Zf);
    I012 = [0; I13; -I13]
    Iabc3 = sctm*I012
    disp('(d) Double line-to-ground fault at bus 3')
    I13 = 1/(Z133 + Z133*(Z033+3*Zf)/(Z133+Z033+3*Zf));
    I23 = -(1.0 - Z133*I13)/Z133;
    I03 = -(1.0 - Z133*I13)/(Z033+3*Zf);
    I012 = [I03; I13; I23]
    Iabc3 = sctm*I012
    MANUAL CALCULATION
    ZERO SEQUENCE NETWORK:

    You might also like