Srs Airbag: Section
Srs Airbag: Section
SR
A
B
SECTION
SRS AIRBAG C
E
CONTENTS
PRECAUTION ............................................... 2 Exploded View .........................................................20 F
Removal and Installation .........................................20
PRECAUTIONS ................................................... 2
Precaution for Supplemental Restraint System SIDE AIR BAG MODULE .................................. 22
G
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN- Removal and Installation .........................................22
SIONER" ................................................................... 2
Service ...................................................................... 2
CRASH ZONE SENSOR ................................... 23
Exploded View .........................................................23 SR
Occupant Classification System .............................. 2
Removal and Installation .........................................23
Precaution for Work .................................................. 2
SATELLITE SENSOR ....................................... 25
PREPARATION ............................................ 4 I
Exploded View .........................................................25
PREPARATION ................................................... 4 Removal and Installation - Front Door Satellite
Special Service Tools ................................................ 4 Sensor .....................................................................25
Removal and Installation - Front Side Air Bag Sat- J
BASIC INSPECTION .................................... 5 ellite Sensor .............................................................26
Removal and Installation - Rear Side Air Bag Sat-
COLLISION DIAGNOSIS .................................... 5 ellite Sensor .............................................................27 K
For Frontal Collision .................................................. 5
For Side and Rollover Collision ................................. 7 AIR BAG DIAGNOSIS SENSOR UNIT ............. 29
Exploded View .........................................................29
REMOVAL AND INSTALLATION ............... 12 Removal and Installation .........................................29 L
The Supplemental Restraint System such as AIR BAG and SEAT BELT PRE-TENSIONER, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the SR and SB section of
this Service Manual.
WARNING:
To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the
battery and wait at least three minutes before performing any service.
Service INFOID:0000000009477603
Do not use electrical test equipment to check SRS circuits unless instructed to in this Service Manual.
Before servicing the SRS, turn ignition switch OFF, disconnect both battery cables and wait at least three
minutes.
For approximately three minutes after the cables are removed, it is still possible for the air bag and seat belt
pre-tensioner to deploy. Therefore, do not work on any SRS connectors or wires until at least three minutes
have passed.
Diagnosis sensor unit must always be installed with their arrow marks pointing towards the front of the
vehicle for proper operation. Also check diagnosis sensor unit for cracks, deformities or rust before installa-
tion and replace as required.
The spiral cable must be aligned with the neutral position since its rotations are limited. Do not turn steering
wheel and column after removal of steering gear.
Handle air bag module carefully. Always place driver and front passenger air bag modules with the pad side
facing upward and seat mounted front side air bag module standing with the stud bolt side facing down.
Conduct self-diagnosis to check entire SRS for proper function after replacing any components.
After air bag inflates, the instrument panel assembly should be replaced if damaged.
Always replace instrument panel pad following front passenger air bag deployment.
Occupant Classification System INFOID:0000000009477602
Replace occupant classification system control unit and passenger front seat frame as an assembly. Refer to
SE-40, "PASSENGER SIDE : Exploded View".
Precaution for Work INFOID:0000000009477604
When removing or disassembling each component, be careful not to damage or deform it. If a component
may be subject to interference, be sure to protect it with a shop cloth.
When removing (disengaging) components with a screwdriver or similar tool, be sure to wrap the component
with a shop cloth or vinyl tape to protect it.
SR
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Tool number Description
(Kent-Moore No.)
Tool name
Removing trim components
(J-46534)
Trim Tool Set
AWJIA0483ZZ
CAUTION:
Due to varying models and option levels, not all parts listed in the chart below apply to all vehicles.
WORK PROCEDURE
1. Before performing any of the following steps, ensure that all vehicle body and structural repairs have been
completed.
2. Check the SRS components using the table below:
Replace any SRS components showing visible signs of damage. (dents, cracks and deformation, etc.)
3. Perform self-diagnosis using CONSULT or air bag warning lamp. Refer to SRC-14, "Description" for
details.
Ensure entire SRS operates properly.
4. After the work is completed, perform self-diagnosis to check that no malfunction is detected. Refer to
SRC-14, "Description".
SRS INSPECTION (FOR FRONTAL COLLISION)
Part Inspection
Driver air bag module If the driver air bag has NOT been activated:
1. Remove driver air bag module. Check harness cover and connectors for damage, terminals
for deformities, and harness for binding.
2. Install driver air bag module into the steering wheel to check fit and alignment with the wheel.
3. If no damage is found, reinstall with new fasteners.
4. If damaged REPLACE. Install driver air bag modules with new fasteners.
Front passenger air bag module If the front passenger air bag has NOT been activated:
(if equipped) 1. Remove front passenger air bag module. Check harness cover and connectors for damage,
terminals for deformities, and harness for binding.
2. Install front passenger air bag module into the instrument panel to check fit with the instrument
panel.
3. If no damage is found, reinstall with new fasteners.
4. If damaged REPLACE. Install front passenger air bag modules with new fasteners.
Crash zone sensor If the front air bags or seat belt pre-tensioners have NOT been activated:
1. Remove the crash zone sensor. Check harness connectors for damage, terminals for defor-
mities, and harness for binding.
2. Check for visible signs of damage (dents, cracks, deformation) of the crash zone sensor and
bracket.
3. Install the crash zone sensor to check fit.
4. If no damage is found, reinstall with new fasteners.
5. If damaged REPLACE the crash zone sensor and bracket with new fasteners.
Part Inspection
Side curtain air bag module LH If the side curtain air bag LH has deployed:
REPLACE the side curtain air bag module LH.
Install with new fasteners.
Side curtain air bag module RH If the side curtain air bag RH has deployed:
REPLACE the side curtain air bag module RH.
Install with new fasteners.
Front side air bag module LH If the front side air bag LH has deployed:
REPLACE front seatback assembly LH.
Front side air bag module RH If the front side air bag RH has deployed:
REPLACE front seatback assembly RH.
Side air bag (satellite) sensor (LH If any of the SRS components have deployed:
or RH) REPLACE the side air bag (satellite) sensor on the collision side with new fasteners.
Door (satellite) sensor (LH or RH) If any of the SRS components have deployed:
REPLACE the door (satellite) sensor on the collision side with new fasteners.
Diagnosis sensor unit If any of the SRS components have deployed:
REPLACE the diagnosis sensor unit with new fasteners.
Seat belt pre-tensioner assem- If either the driver or passenger seat belt pre-tensioner* has been activated:
blies REPLACE all seat belt pre-tensioner assemblies with new fasteners.
(All applicable locations: buckle, *: Confirm seat belt pre-tensioner activation using CONSULT only.
retractor, lap outer)
Center inner pillar 1. Check the center inner pillar on the collision side for damage (dents, cracks, deformation).
2. If damaged REPAIR the center inner pillar.
Seat (if equipped with front side If either the front LH or front RH side air bag modules has been deployed:
air bag) REPLACE front seatback assembly on the deployed side.
Trim/headlining 1. Check for visible signs of damage (dents, cracks, deformation) of the interior trim on the colli-
sion side.
2. If damaged REPLACE the damaged trim parts.
Door-mounted curtain air bag If the door-mounted curtain air bag module LH has been deployed:
module LH REPLACE the door finisher LH and door-mounted curtain air bag module.
Install with new fasteners.
Door-mounted curtain air bag If the door-mounted curtain air bag module RH has been deployed:
module RH REPLACE the door finisher RH and door-mounted curtain air bag module.
Install with new fasteners.
Occupant classification system 1. Remove passenger seat assembly.
(Passenger seat) 2. Check control unit case for dents, cracks of deformities.
3. Check connectors for damage and terminals for deformities.
4. Check seat frame and cushion pan for dents or deformities.
5. If no damage is found, reinstall seat with new fasteners.
6. If damaged REPLACE seat cushion assembly with new fasteners.
7. Perform zero point reset function after front passenger seat is installed in the vehicle and all
bolts are tightened to specification. Refer to SRC-38, "ZERO POINT RESET : Special Repair
Requirement".
Pop-up roll bar assemblies If the pop-up roll bar has deployed:
REPLACE pop-up roll bar assemblies and pop-up roll bar covers.
Install with new fasteners.
Part Inspection
F
Side curtain air bag module LH If the side curtain air bag LH has NOT deployed:
1. Check for visible signs of damage (dents, tears, deformation) of the center pillar on the colli-
sion side.
2. If damaged - Remove the side curtain air bag module LH. G
3. Check for visible signs of damage (tears etc.) of the side curtain air bag module LH.
4. Check harness and connectors for damage, and terminals for deformities.
5. If no damage is found, reinstall the side curtain air bag module LH with new fasteners.
6. If damaged REPLACE the side curtain air bag module LH with new fasteners. SR
Side curtain air bag module RH If the side curtain air bag RH has NOT deployed:
1. Check for visible signs of damage (dents, tears, deformation) of the center pillar on the colli-
sion side. I
2. If damaged - Remove the side curtain air bag module RH.
3. Check for visible signs of damage (tears etc.) of the side curtain air bag module RH.
4. Check harness and connectors for damage, and terminals for deformities.
5. If no damage is found, reinstall the side curtain air bag module RH with new fasteners. J
6. If damaged REPLACE the side curtain air bag module RH with new fasteners.
Front side air bag module LH If the front LH side air bag has NOT deployed:
1. Check for visible signs of damage (dents, tears, deformation) of the seat back on the collision
K
side.
2. Check harness and connectors for damage, and terminals for deformities.
3. If damaged REPLACE the front seatback assembly LH.
Front side air bag module RH If the front side air bag RH has NOT deployed: L
1. Check for visible signs of damage (dents, tears, deformation) of the seat back on the collision
side.
2. Check harness and connectors for damage, and terminals for deformities.
M
3. If damaged REPLACE the front seatback assembly RH.
Side air bag (satellite) sensor (LH If none of the SRS components have been activated:
or RH) 1. Remove the side air bag (satellite) sensor (LH or RH) on the collision side. Check harness
connectors for damage, terminals for deformities, and harness for binding. N
2. Check for visible signs of damage (dents, cracks, deformation) of the side air bag (satellite)
sensor (LH or RH).
3. Install the side air bag (satellite) sensor (LH or RH) to check fit.
4. If no damage is found, reinstall the side sir bag (satellite) sensor (LH or RH) with new fasten- O
ers.
5. If damaged REPLACE the side air bag (satellite) sensor (LH or RH) with new fasteners.
Door (satellite) sensor (LH or RH) If none of the SRS components have been activated: P
1. Remove the door (satellite) sensor (LH or RH) on the collision side. Check harness connec-
tors for damage, terminals for deformities, and harness for binding.
2. Check for visible signs of damage (dents, cracks, deformation) of the door (satellite) sensor
(LH or RH).
3. Install the door (satellite) sensor (LH or RH) to check fit.
4. If no damage is found, reinstall the door (satellite) sensor (LH or RH) with new fasteners.
5. If damaged REPLACE the door (satellite) sensor (LH or RH) with new fasteners.
SR
AWHIA0452ZZ
WARNING:
Before servicing the SRS, turn ignition switch OFF, disconnect both battery terminals then wait at
least three minutes.
Always work from the side of driver air bag module. Do not work in front of it.
If driver air bag module is being replaced due to deployment, the spiral cable must also be replaced.
Refer to SR-15, "Removal and Installation".
Do not insert any foreign objects (screwdriver, etc.) into the driver air bag module.
Do not attempt to disassemble the driver air bag module.
Do not expose the driver air bag module to temperatures exceeding 90C (194F).
Do not use air tools or electric tools for servicing.
CAUTION:
Do not allow oil, grease, detergent or water to come in contact with the driver air bag module.
REMOVAL
1. Disconnect negative and positive battery terminals, then wait at least three minutes. Refer to PG-67,
"Removal and Installation (Battery)".
G
AWHIA0528ZZ
4. Lift driver air bag module away from the steering wheel and dis-
connect the driver air bag module harness connectors (A) and SR
the horn harness connector (B). Then remove the harnesses
from hook (C).
NOTE: I
Take note of harness routing for correct installation.
AWHIA0551ZZ
K
CAUTION:
For removing/installing the driver air bag module harness
connector, insert a thin screwdriver wrapped in tape into L
the notch, then lift the lock and remove the harness con-
nector as shown.
Install the harness connector with the lock raised, and M
push the lock into the connector as shown.
After installing the connector, check that the lock is
pushed in securely.
N
PHIA0953J
O
JMHIA2077ZZ
JMHIA0009ZZ
INSTALLATION
Installation is in the reverse order of removal.
NOTE:
To install the driver air bag module onto the steering wheel, align the hooks over the springs and push to snap
into place.
CAUTION:
Always route driver air bag module harness in original location.
Be careful not to damage or pinch the harness while installing.
After the work is completed, check the function of the horn and each steering switch.
After the work is completed, perform diagnosis to check that no malfunction is detected. Refer to
SRC-14, "Description".
G
AWHIA0504ZZ
I
WARNING:
Before servicing the SRS, turn ignition switch OFF, disconnect both battery terminals then wait at
least three minutes. J
Do not disassemble the spiral cable.
Do not use air tools or electric tools for servicing.
CAUTION:
Do not allow oil, grease, detergent or water to come in contact with the spiral cable. K
REMOVAL
1. Disconnect negative and positive battery terminals, then wait at least three minutes. Refer to PG-67, L
"Removal and Installation (Battery)".
2. Remove steering wheel. Refer to ST-8, "Removal and Installation".
3. Remove steering column covers. Refer to IP-17, "Removal and Installation". M
4. Disconnect the harness connector (A) from spiral cable and har-
ness connector (B) from steering angle sensor.
N
P
ALHIA0272ZZ
AWHIA0538ZZ
6. Remove screws (A), then release pawls (B) and separate the
steering angle sensor (2) from spiral cable (1).
CAUTION:
Do not reuse steering angle sensor.
ALHIA0271ZZ
CAUTION:
Do not strike or drop the spiral cable.
Replace the spiral cable if it has been dropped or sustained
an impact.
JMHIA0009ZZ
INSTALLATION
Installation is in the reverse order of removal.
The turn signal lever must be in the neutral position for spiral cable installation.
G
AWHIA0531ZZ
CAUTION: SR
The spiral cable may snap during steering operation if the spiral cable is installed in an improper
position.
Do not overturn the spiral cable or go beyond the maximum number of turns allowed. This will cause
the cable to snap. I
Do not apply lubricant to the spiral cable.
Do not allow oil, grease, detergent or water to come in contact with the spiral cable.
After the work is completed, perform diagnosis to check that no malfunction is detected. Refer to J
SRC-14, "Description".
AWHIA0529ZZ
WARNING:
Before servicing the SRS, turn ignition switch OFF, disconnect both battery terminals then wait at
least three minutes.
Always work from the side of air bag module. Do not work in front of it.
Do not expose the front passenger air bag module to temperatures exceeding 90C (194F).
Do not attempt to disassemble the front passenger air bag module.
Do not insert any foreign objects (screwdriver, etc.) into the front passenger air bag module.
Do not use air tools or electric tools for servicing.
CAUTION:
Do not allow oil, grease, detergent, or water to come in contact with the front passenger air bag mod-
ule.
REMOVAL
1. Disconnect negative and positive battery terminals, then wait at least three minutes. Refer to PG-67,
"Removal and Installation (Battery)".
2. Remove the glove box assembly. Refer to IP-25, "Removal and Installation".
JMHIA2022ZZ
D
5. Release pawls using a suitable tool and remove front passenger
air bag module (1).
: Pawl E
G
AWHIA0527ZZ
CAUTION:
SR
Always place the front passenger air bag module with pad
side facing upward.
: Upward
I
K
JMHIA2461ZZ
JMHIA0009ZZ
O
INSTALLATION
Installation is in the reverse order of removal. P
CAUTION:
Do not reuse the front passenger air bag module bolts.
Do not damage the front passenger air bag module harness during installation.
After the work is completed, perform diagnosis to check that no malfunction is detected. Refer to
SRC-14, "Description".
JMHIA2457GB
WARNING:
Before servicing the SRS, turn ignition switch OFF, disconnect both battery terminals then wait at
least three minutes.
Always work from the side of air bag module. Do not work in front of it.
Replace the side curtain air bag module if it has been dropped or sustained an impact.
Do not attempt to disassemble the side curtain air bag module.
Do not strike the side curtain air bag module.
Do not insert any objects (screwdriver, etc.) into the side curtain air bag module.
Do not expose the side curtain air bag module to temperatures exceeding 93C (200F).
Do not use air tools or electric tools for servicing.
CAUTION:
Do not allow oil, grease, detergent or water to come in contact with the side curtain air bag module.
REMOVAL
1. Disconnect negative and positive battery terminals, then wait at least three minutes. Refer to PG-67,
"Removal and Installation (Battery)".
2. Remove the headlining. Refer to INT-31, "Removal and Installation".
3. Disconnect the harness connector from the side curtain air bag module.
CAUTION:
PHIA0953J
D
4. Remove the tether bolt, then the remaining side curtain air bag module bolts.
INSTALLATION
Installation is in the reverse order of removal. E
WARNING:
When installing the side curtain air bag module make sure it is not twisted between attachment brack-
ets. F
CAUTION:
Make sure to attach the double stick tape to the tether and adhere it to the pillar.
Do not damage the harness while installing the side curtain air bag module.
G
After the work is completed, perform self-diagnosis to check that no malfunction is detected. Refer
to SRC-14, "Description".
SR
The side air bag module is part of the front seatback. Refer to SE-24, "DRIVER SIDE : Side Air Bag Module"
(DRIVER SIDE) or SE-25, "PASSENGER SIDE : Side Air Bag Module" (PASSENGER SIDE).
SR
J
ALHIA0305ZZ
L
WARNING:
Before servicing the SRS, turn ignition switch OFF, disconnect both battery terminals then wait at
least three minutes.
Replace the crash zone sensor if it has been dropped or sustained an impact. M
Replace the crash zone sensor if either the driver air bag module, the front passenger air bag mod-
ule, or a front seat belt pre-tensioner has been deployed.
Do not strike the crash zone sensor. N
Do not use air tools or electric tools for servicing.
REMOVAL
1. Disconnect negative and positive battery terminals, then wait at least three minutes. Refer to PG-67, O
"Removal and Installation (Battery)".
ALHIA0306ZZ
4. Disconnect the slide double locking type harness connector from the crash zone sensor, as shown.
INSTALLATION
Installation is in the reverse order of removal.
Position the crash zone sensor using the locating pin before tightening the nut to specification.
CAUTION:
Do not reuse the crash zone sensor nut.
Do not damage the harness connector during installation.
After the work is completed, perform diagnosis to check that no malfunction is detected. Refer to
SRC-14, "Description".
SR
J
AWHIA0530ZZ
1. Front door satellite sensor 2. Front side air bag satellite sensor 3. Rear side air bag satellite sensor K
Front
WARNING:
Before servicing the SRS, turn ignition switch OFF, disconnect both battery terminals then wait at M
least three minutes.
Replace the front door satellite sensor if it has been dropped or sustained an impact.
Do not use air tools or electric tools for servicing.
Replace the front door satellite sensor (LH/RH) if either the side air bag module or the side curtain air N
bag module has been deployed.
Do not strike the front door satellite sensor.
O
REMOVAL
1. Disconnect negative and positive battery terminals, then wait at least three minutes. Refer to PG-67,
"Removal and Installation (Battery)".
P
2. Remove front door finisher. Refer to INT-15, "Removal and Installation".
WARNING:
Before servicing the SRS, turn ignition switch OFF, disconnect both battery terminals then wait at
least three minutes.
Do not strike the front side air bag satellite sensor.
Replace the front side air bag satellite sensor if it has been dropped or sustained an impact.
Do not use air tools or electric tools for servicing.
Replace the front side air bag satellite sensor (LH/RH) if either the side air bag module or the side
curtain air bag module has been deployed.
REMOVAL
1. Disconnect negative and positive battery terminals, then wait at least three minutes. Refer to PG-67,
"Removal and Installation (Battery)".
2. Remove center pillar lower finisher. Refer to INT-25, "CENTER PILLAR LOWER FINISHER : Removal
and Installation".
3. Remove and discard front side air bag satellite sensor nut.
CAUTION:
Do not reuse front side air bag satellite sensor nut.
4. Remove front side air bag satellite sensor.
G
INSTALLATION
Installation is in the reverse order of removal.
Position the front side air bag satellite sensor using the locating pin before tightening the nut to specification. SR
CAUTION:
Do not reuse the front side air bag satellite sensor nut.
Do not damage the harness connector during installation.
I
After the work is completed, perform self-diagnosis to check that no malfunction is detected. Refer
to SRC-14, "Description".
Removal and Installation - Rear Side Air Bag Satellite Sensor INFOID:0000000009460337 J
WARNING:
Before servicing the SRS, turn ignition switch OFF, disconnect both battery terminals then wait at
K
least three minutes.
Replace the rear side air bag satellite sensor if it has been dropped or sustained an impact.
Replace the rear side air bag satellite sensor (LH/RH) if either the side air bag module or the side cur-
tain air bag module has been deployed. L
Do not strike the rear side air bag satellite sensor.
Do not use air tools or electric tools for servicing.
REMOVAL M
1. Disconnect negative and positive battery terminals, then wait at least three minutes. Refer to PG-67,
"Removal and Installation (Battery)".
2. Remove luggage side lower finisher. Refer to INT-34, "LUGGAGE SIDE LOWER FINISHER : Removal N
and Installation".
4. Remove and discard rear side air bag satellite sensor bolt.
CAUTION:
Do not reuse rear side air bag satellite sensor bolt.
5. Remove rear side air bag satellite sensor.
INSTALLATION
Installation is in the reverse order of removal.
Position the rear side air bag satellite sensor using the locating pin before tightening the bolt to specification.
CAUTION:
Do not reuse rear side air bag satellite sensor bolt.
Do not damage the harness connector during installation.
After the work is completed, perform self-diagnosis to check that no malfunction is detected. Refer
to SRC-14, "Description".
SR
J
AWHIA0553ZZ
L
REMOVAL
WARNING:
Before servicing the SRS, turn ignition switch OFF, disconnect both battery terminals then wait at M
least three minutes.
Replace the air bag diagnosis sensor unit if any SRS air bag has been deployed or if any front seat
belt pre-tensioner has been deployed. N
Before disconnecting the air bag diagnosis sensor unit harness connectors, be sure to disconnect
each harness connector of the front seat belt pre-tensioners (LH/RH) to prevent accidental air bag
deployment by static electricity and seat belt pre-tensioner operation.
Do not use the air tools or electric tools for servicing. O
When replacing the air bag diagnosis sensor unit, always check with the parts department for the lat-
est parts information. Installing an incorrect air bag diagnosis sensor unit may or may not cause the
air bag warning lamp to illuminate and may cause incorrect deployment of the supplemental air bags P
and seat belt pre-tensioners in a collision resulting in serious personal injury or death.
1. Always check the air bag diagnosis sensor unit ECU discriminated number (identification number) or part
number using CONSULT.
2. Disconnect negative and positive battery terminals, then wait at least three minutes. Refer to PG-67,
"Removal and Installation (Battery)".
3. Remove center pillar lower finisher. Refer to INT-25, "CENTER PILLAR LOWER FINISHER : Removal
and Installation".
PHIA0953J
5. Remove the center console assembly. Refer to IP-18, "Removal and Installation".
6. Disconnect the harness connectors (A) from the air bag diagno-
sis sensor unit.
7. Remove and discard bolts (B), then remove bracket and air bag
diagnosis sensor unit.
CAUTION:
Do not reuse air bag diagnosis sensor unit bolts.
NOTE:
Shown with bracket removed for clarity.
: Front
JMHIA2027ZZ
CAUTION:
Do not strike the air bag diagnosis sensor unit.
Replace the air bag diagnosis sensor unit if it has been
dropped or sustained an impact.
SGI787
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
Do not reuse the air bag diagnosis sensor unit bolts.
The air bag diagnosis sensor unit must always be installed with the label arrow mark " " pointing
toward the front of the vehicle for proper operation.
Do not damage the air bag diagnosis sensor unit harness or connectors during installation.
After replacing the air bag diagnosis sensor unit, confirm using CONSULT that the ECU discrimi-
nated number (identification number) or part number of the new replacement air bag diagnosis sen-
sor unit matches the ECU discriminated number (identification number) or part number of the
replaced (old) air bag diagnosis sensor unit.
After the work is completed, perform diagnosis to check that no malfunction is detected. Refer to
SRC-14, "Description".
NOTE:
If the ECU discriminated number or part number of the new replacement air bag diagnosis sensor unit differs
from the ECU discriminated number or part number of the replaced air bag diagnosis sensor unit, reconfirm
the parts information and verify that the correct air bag diagnosis sensor unit was installed.
SR
The front seat belt pre-tensioner is part of the front seat belt retractor. Refer to SB-9, "SEAT BELT RETRAC-
TOR : Removal and Installation".
The front seat belt buckle switch is part of the front seat belt buckle. Refer to SB-8, "FRONT SEAT BELT B
BUCKLE : Removal and Installation".
SR
Removal
1. Remove cluster lid C. Refer to IP-22, "Removal and Installation".
2. Release pawls and remove front passenger air bag off indicator
(1) from cluster lid C (2).
: Pawl
ALHIA0308ZZ
Installation
Installation is in the reverse order of removal.