Srs Airbag: Section
Srs Airbag: Section
Srs Airbag: Section
SECTION SR
SRS AIRBAG
B
E
CONTENTS
FOR USA AND CANADA Exploded View .........................................................17 F
Removal and Installation .........................................17
PRECAUTION ............................................... 3
SIDE CURTAIN AIR BAG MODULE ................ 19
G
PRECAUTIONS ................................................... 3 Exploded View .........................................................19
Precaution for Supplemental Restraint System Removal and Installation .........................................19
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" ................................................................... 3 CRASH ZONE SENSOR ................................... 21 SR
Service ...................................................................... 3 Exploded View .........................................................21
Occupant Classification System .............................. 3 Removal and Installation .........................................21
FOR SIDE AND ROLLOVER COLLISION ............... 33 SIDE CURTAIN AIR BAG MODULE ................. 47
FOR SIDE AND ROLLOVER COLLISION : When Exploded View ........................................................ 47
SRS is activated in a collision ................................. 33 Removal and Installation ......................................... 47
FOR SIDE AND ROLLOVER COLLISION : When
SRS is not activated in a collision ........................... 34
CRASH ZONE SENSOR ................................... 49
Exploded View ........................................................ 49
REMOVAL AND INSTALLATION ............... 37 Removal and Installation ......................................... 49
DRIVER AIR BAG MODULE ............................. 37 SIDE AIR BAG (SATELLITE) SENSOR ........... 51
Exploded View ........................................................ 37 Exploded View ........................................................ 51
Removal and Installation ........................................ 37 Removal and Installation ......................................... 51
FRONT PASSENGER AIR BAG MODULE ....... 43 FRONT SEAT BELT PRE-TENSIONER ........... 55
Exploded View ........................................................ 43 Removal and Installation ......................................... 55
PRECAUTION A
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT B
PRE-TENSIONER" INFOID:0000000005518899
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along C
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted. D
Information necessary to service the system safely is included in the “SRS AIR BAG” and “SEAT BELT” of this
Service Manual.
WARNING: E
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
F
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the “SRS AIR BAG”.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this G
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS SR
WARNING:
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the
ignition ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) I
with a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly
causing serious injury.
• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the J
battery, and wait at least 3 minutes before performing any service.
Service INFOID:0000000005518900
K
• Do not use electrical test equipment to check SRS circuits unless instructed to in this Service Manual.
• Before servicing the SRS, turn ignition switch OFF, disconnect battery negative terminal and wait at least 3
minutes.
L
For approximately 3 minutes after the battery negative terminal is removed, it is still possible for the air bag
and seat belt pre-tensioner to deploy. Therefore, do not work on any SRS connectors or wires until at least 3
minutes have elapsed.
• Diagnosis sensor unit must always be installed with their arrow marks “⇐” pointing towards the front of the M
vehicle for proper operation. Also check diagnosis sensor unit for cracks, deformities or rust before installa-
tion and replace as required.
• The spiral cable must be aligned in the neutral position since its rotations are limited. Do not turn steering
N
wheel and column after removal of steering gear.
• Handle air bag module carefully. Always place driver and front passenger air bag modules with the pad side
facing upward and seat mounted front side air bag module standing with the stud bolt side facing down.
• Conduct self-diagnosis to check entire SRS for proper functioning after replacing any components. O
• After air bag inflates, the front instrument panel assembly should be replaced if damaged.
• Always replace instrument panel pad following front passenger air bag deployment.
Occupant Classification System INFOID:0000000005518901
P
• Replace occupant classification system control unit and passenger front seat cushion as an assembly.
Refer to SE-112, "Removal and Installation".
PREPARATION
PREPARATION
Commercial Service Tools INFOID:0000000005518902
S-NT757
JMKIA3050ZZ
BASIC INSPECTION A
COLLISION DIAGNOSIS
FOR FRONTAL COLLISION
B
FOR FRONTAL COLLISION : When SRS is activated in a collision INFOID:0000000005681357
CAUTION: C
Due to varying models and option levels, not all parts listed in the chart below apply to all vehicles.
WORK PROCEDURE
1. Before performing any of the following steps, ensure that all vehicle body and structural repairs have been D
completed.
2. Replace the diagnosis sensor unit.
3. Remove the front air bag modules, crash zone sensor, bracket and seat belt pre-tensioner assemblies. E
4. Check the SRS components using the table below:
Replace any SRS components showing visible signs of damage. (dents, cracks and deformation, etc.)
5. Install new front air bag modules, crash zone sensor assembly, bracket and seat belt pre-tensioner F
assemblies.
6. Perform self-diagnosis using CONSULT-III or air bag warning lamp. Refer to SRC-17, "Diagnosis Descrip-
tion" for details. Ensure entire SRS operates properly. G
7. After the work is completed, perform self-diagnosis to check that no malfunction is detected. Refer to
SRC-17, "Diagnosis Description".
SR
SRS INSPECTION (FOR FRONTAL COLLISION)
Part Inspection
I
If the driver air bag has deployed:
Driver air bag module REPLACE
Install with new fasteners.
If the front passenger air bag has deployed:
J
Front passenger air bag module
REPLACE
(if equipped)
Install with new fasteners.
If any of the front air bags or seat belt pre-tensioners* have been activated: K
Crash zone sensor REPLACE the crash zone sensor and bracket with new fasteners.
*: Confirm seat belt pre-tensioner activation using CONSULT-III only.
Seat belt pre-tensioner assem- L
If either the driver or passenger seat belt pre-tensioner* has been activated:
blies
REPLACE all seat belt pre-tensioner assemblies with new fasteners.
(All applicable locations: buckle,
*: Confirm seat belt pre-tensioner activation using CONSULT-III only.
retractor, lap outer)
M
If any of the SRS components have been activated:
Diagnosis sensor unit REPLACE the diagnosis sensor unit.
Install with new fasteners.
1. Visually check steering wheel for deformities. N
2. Check harness (built into steering wheel) and connectors for damage, and terminals for defor-
mities.
Steering wheel 3. Install driver air bag module into the steering wheel to check fit and alignment with the wheel.
4. Check steering wheel for excessive free play. O
5. If no damage is found, reinstall.
6. If damaged − REPLACE.
If the driver front air bag has deployed: P
Spiral cable
REPLACE the spiral cable.
1. Remove passenger seat assembly.
2. Check control unit case for dents, cracks of deformities.
Occupant classification system 3. Check connectors and pressure sensor tube for damage, and terminals for deformities.
(Passenger seat) 4. Check seat frame and cushion pan for dents or deformities.
5. If no damage is found, reinstall seat with new fasteners.
6. If damaged − REPLACE seat cushion assembly with new fasteners.
CAUTION:
Due to varying models and option levels, not all parts listed in the chart below apply to all vehicles.
WORK PROCEDURE
1. Before performing any of the following steps, ensure that all vehicle body and structural repairs have been
completed.
2. Check the SRS components using the table below:
Replace any SRS components showing visible signs of damage. (dents, cracks and deformation, etc.)
3. Perform self-diagnosis using CONSULT-III or air bag warning lamp. Refer to SRC-17, "Diagnosis Descrip-
tion" for details. Ensure entire SRS operates properly.
4. After the work is completed, perform self-diagnosis to check that no malfunction is detected. Refer to
SRC-17, "Diagnosis Description".
SRS INSPECTION (FOR FRONTAL COLLISION)
Part Inspection
If the driver air bag has NOT been deployed:
1. Remove driver air bag module. Check harness cover and connectors for damage, terminals for
deformities, and harness for binding.
Driver air bag module
2. Install driver air bag module into the steering wheel to check fit and alignment with the wheel.
3. If no damage is found, reinstall with new fasteners.
4. If damaged − REPLACE. Install driver air bag module with new fasteners.
If the front passenger air bag has NOT been deployed:
1. Remove front passenger air bag module. Check harness cover and connectors for damage, ter-
minals for deformities, and harness for binding.
Front passenger air bag module
2. Install front passenger air bag module into the instrument panel to check fit with the instrument
(if equipped)
panel.
3. If no damage is found, reinstall with new fasteners.
4. If damaged − REPLACE. Install front passenger air bag modules with new fasteners.
If the front air bags or seat belt pre-tensioners have NOT been activated:
1. Remove the crash zone sensor. Check harness connectors for damage, terminals for deformi-
ties, and harness for binding.
2. Check for visible signs of damage (dents, cracks, deformation, etc.) of the crash zone sensor
Crash zone sensor
and bracket.
3. Install the crash zone sensor to check fit.
4. If no damage is found, reinstall with new fasteners.
5. If damaged − REPLACE the crash zone sensor and bracket with new fasteners.
If the pre-tensioners have NOT been activated:
1. Remove seat belt pre-tensioners.
Check harness cover and connectors for damage, terminals for deformities, and harness for
binding.
Seat belt pre-tensioner assem-
2. Check belts for damage and anchors for loose mounting.
blies
3. Check retractor for smooth operation.
(All applicable locations: buckle,
4. Check seat belt adjuster for damage.
retractor, lap outer)
5. Check for deformities of the center pillar inner.
6. If the center pillar inner has no damage, REPLACE the seat belt pre-tensioner assembly.
7. If no damage is found, reinstall seat belt pre-tensioner assembly.
8. If damaged − REPLACE. Install the seat belt pre-tensioners with new fasteners.
CAUTION: L
Due to varying models and option levels, not all parts listed in the chart below apply to all vehicles.
WORK PROCEDURE
M
1. Before performing any of the following steps, ensure that all vehicle body and structural repairs have been
completed.
2. Replace the following components:
• Front seat back assembly (on the side on which side air bag is activated) N
• Door finisher (on the side on which door-mounted curtain air bag is activated)
• Pop-up roll bar assemblies and pop-up roll bar covers
• Side air bag (satellite) sensor LH/RH (on the side on which side air bag is activated) O
• Diagnosis sensor unit
• Seat belt pre-tensioner assemblies
3. Check the SRS components and the related parts using the following table. P
Replace any SRS components and the related parts showing visible signs of damage. (dents, cracks,
deformation, etc.)
4. Perform self-diagnosis using CONSULT-III and “AIR BAG” warning lamp. Refer to SRC-17, "Diagnosis
Description" for details. Make sure entire SRS operates properly.
5. After the work is completed, perform self-diagnosis to check that no malfunction is detected. Refer to
SRC-17, "Diagnosis Description".
Part Inspection
If the side curtain air bag LH has deployed:
Side curtain air bag module LH REPLACE the side curtain air bag module LH.
Install with new fasteners.
If the side curtain air bag RH has deployed:
Side curtain air bag module RH REPLACE the side curtain air bag module RH.
Install with new fasteners.
If the front side air bag LH has deployed:
Front side air bag module LH
REPLACE front seatback assembly LH.
If the front side air bag RH has deployed:
Front side air bag module RH
REPLACE front seatback assembly RH.
Side air bag (satellite) sensor If any of the SRS components have deployed:
(LH or RH) REPLACE the side air bag (satellite) sensor on the collision side with new fasteners.
If any of the SRS components have deployed:
Diagnosis sensor unit
REPLACE the diagnosis sensor unit with new fasteners.
Seat belt pre-tensioner assem-
If either the driver or passenger seat belt pre-tensioner* has been activated:
blies
REPLACE all seat belt pre-tensioner assemblies with new fasteners.
(All applicable locations: buckle,
*: Confirm seat belt pre-tensioner activation using CONSULT-III only.
retractor, lap outer)
1. Check the center inner pillar on the collision side for damage (dents, cracks, deformation, etc.).
Center inner pillar
2. If damaged − REPAIR the center inner pillar.
1. Check for visible signs of damage (dents, cracks, deformation, etc.) of the interior trim on the
Trim/headlining collision side.
2. If damaged − REPLACE the damaged trim parts.
If the door-mounted curtain air bag module LH has deployed:
Door-mounted curtain air bag
REPLACE the door finisher LH and door-mounted curtain air bag module.
module LH
Install with new fasteners.
If the door-mounted curtain air bag module RH has deployed:
Door-mounted curtain air bag
REPLACE the door finisher RH and door-mounted curtain air bag module.
module RH
Install with new fasteners.
If the pop-up roll bar has deployed:
Pop-up roll bar assemblies REPLACE pop-up roll bar assemblies and pop-up roll bar covers.
Install with new fasteners.
FOR SIDE AND ROLLOVER COLLISION : When SRS is not activated in a collision
INFOID:0000000005681360
CAUTION:
Due to varying models and option levels, not all parts listed in the chart below apply to all vehicles.
WORK PROCEDURE
1. Before performing any of the following steps, ensure that all vehicle body and structural repairs have been
completed.
2. Check the SRS components and the related parts using the following table.
• If the front seat back assembly is damaged, the front seat back assembly must be replaced.
• If the door finisher assembly is damaged, the door finisher assembly and door-mounted curtain air bag
module must be replaced.
3. Perform self-diagnosis using CONSULT-III and “AIR BAG” warning lamp. Refer to SRC-17, "Diagnosis
Description" for details. Make sure entire SRS operates properly.
4. After the work is completed, perform self-diagnosis to check that no malfunction is detected. Refer to
SRC-17, "Diagnosis Description".
SRS INSPECTION (FOR SIDE AND ROLLOVER COLLISION)
JMHIA0503GB
SR
1. Steering wheel 2. Driver air bag module 3. Side lid (LH/RH)
4. TORX bolt (LH/RH)
Refer to GI-4, "Components" for symbols in the figure. I
J
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait 3 minutes
or more.
• Always work from the side of air bag module. Never work in front of it. K
• Never use the air tools or electric tools for servicing.
REMOVAL
L
1. Remove the side lids (LH/RH).
2. Remove the TORX bolts (LH/RH) from the steering wheel (1)
lower side using TORX bit (A). M
JMHIA0265ZZ
P
3. Pull out the driver air bag module.
PHIA0953J
: Upward
JMHIA0504ZZ
JMHIA0009ZZ
• Never insert any foreign objects (screwdriver, etc.) into the driver air bag module.
• Never disassemble the driver air bag module.
• Never expose the driver air bag module to temperatures exceeding 90 °C (194 °F).
• Never allow oil, grease, detergent, or water to come in contact with the driver air bag module.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• Never use the old TORX bolts after removal, replace with the new bolts.
• Fix the driver air bag harness to the harness fixing hook (A).
JMHIA0505ZZ
SR
JMHIA0506ZZ
1. Steering column cover (upper) 2. Spiral cable 3. Steering column cover (lower)
4. Steering column assembly
A. Driver air bag harness connector
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait 3 minutes
or more.
• Never use the air tools or electric tools for servicing.
REMOVAL
1. Remove the driver air bag module. Refer to SR-11, "Removal and Installation".
2. Remove the steering wheel. Refer to ST-17, "Removal and Installation".
3. Remove the steering column cover (upper/lower). Refer to IP-12, "Exploded View".
4. Disconnect the spiral cable body side harness connectors (A).
NOTE:
Disconnect the spiral cable body side harness connectors after
removing the spiral cable.
JMHIA0507ZZ
JMHIA0508ZZ
D
7. Pull out forward the spiral cable.
CAUTION:
• Never impact the spiral cable. E
• Never impact the spiral cable by dropping, etc. Replace the
spiral cable if it has been dropped or sustained an impact.
F
JMHIA0009ZZ SR
JMHIA0657ZZ
G
JMHIA0509GB
I
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait 3 minutes
or more. J
• Always work from the side of air bag module. Never work in front of it.
• Never use the air tools or electric tools for servicing.
REMOVAL K
1. Remove the glove box lid assembly. Refer to IP-13, "Removal and Installation".
2. Remove the Instrument lower assist panel. Refer to IP-13, "Removal and Installation".
3. Disconnect the front passenger air bag harness connector (A). L
4. Remove the front passenger air bag module fixing bolt (B).
NOTE:
The figure shows the installed front passenger air bag module. M
(Under view of the module installed without glove box cover.)
JMHIA0510ZZ
O
5. Remove the instrument panel assembly (1). Refer to IP-13, "Removal and Installation".
P
JMHIA0511ZZ
CAUTION:
• Always place the front passenger air bag module with pad
side facing upward.
: Upward
JMHIA0512ZZ
JMHIA0009ZZ
• Never insert any foreign objects (screwdriver, etc.) into front passenger air bag module.
• Never disassembly the front passenger air bag module.
• Never expose the front passenger air bag module to temperatures exceeding 90 °C (194 °F).
• Never allow oil, grease, detergent, or water to come in contact with the front passenger air bag mod-
ule.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• Never use the old fixing bolts after removal, replace with the new bolts.
• Never damage the harness while installing.
• If malfunction is detected by the air bag warning lamp, after repair or replacement of the malfunc-
tioning parts, reset the memory using self-diagnosis or CONSULT-III. Refer to SRC-17, "Diagnosis
Description".
• After the work is completed, check that no system malfunction is detected by air bag warning lamp.
G
JMHIA0513GB
1. Side curtain air bag inflator 2. Side curtain air bag 3. Strap
A. Side curtain air bag harness connec- B. Ground bolt SR
tor
Refer to GI-4, "Components" for symbols in the figure.
I
Removal and Installation INFOID:0000000005518910
WARNING: J
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait 3 minutes
or more.
• Never use air tools or electric tools for servicing.
K
REMOVAL
1. Remove the headlining.
• Normal roof models: Refer to INT-27, "NORMAL ROOF : Removal and Installation". L
• Sunroof models: Refer to INT-30, "SUNROOF : Removal and Installation".
2. Remove the side curtain air bag harness connector.
CAUTION:
M
• For installing/removing the side curtain air bag harness
connector, insert thin screwdriver wrapped in tape into
notch, lift lock and remove the connector.
• Install the connector with lock raised, and push lock into N
the connector.
• After installing the connector, check that the lock is
pushed securely into it. O
P
PHIA0953J
3. Remove the fixing bolts, and then remove the side curtain air bag module.
CAUTION:
JMHIA0009ZZ
• Never insert any foreign objects (screwdriver, etc.) into the side curtain air bag module.
• Never disassemble the side curtain air bag module.
• Never expose the side curtain air bag module to temperatures exceeding 90 °C (194 °F).
• Never allow oil, grease, detergent, or water to come in contact with the side curtain air bag module.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• If malfunction is detected by the air bag warning lamp, after repair or replacement of the malfunc-
tioning parts, reset the memory using self-diagnosis or CONSULT-III. Refer to SRC-19, "CONSULT-III
Function".
• After the work is completed, check that no system malfunction is detected by air bag warning lamp.
G
JMHIA0515GB
WARNING: J
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait 3 minutes
or more.
• Never use air tools or electric tools for servicing.
K
REMOVAL
1. Remove the radiator cover grill (RH). Refer to EM-31, "Exploded View".
2. Remove the air duct (inlet). Refer to EM-31, "Exploded View". L
3. Remove the crash zone sensor fixing nuts.
4. Disconnect the crash zone sensor harness connector, and then remove the crash zone sensor.
CAUTION: M
• Never impact the crash zone sensor.
• Replace the crash zone sensor if it has been dropped or sus-
tained an impact. N
P
JMHIA0009ZZ
• Replace the crash zone sensor of deployed SRS driver air bag and deployed SRS front passenger air
bag.
INSTALLATION
Install in the reverse order of removal.
G
JMHIA0516GB
WARNING: J
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait 3 minutes
or more.
• Never use the air tools or electric tools for servicing.
K
REMOVAL
1. Remove the front seat belt. Refer to SB-7, "SEAT BELT RETRACTOR : Removal and Installation".
2. Remove the side air bag (satellite) sensor fixing nuts. L
3. Disconnect the side air bag (satellite) sensor harness connector, and then remove the side air bag (satel-
lite) sensor.
M
CAUTION:
• Never impact the side air bag (satellite) sensor.
• Replace the side air bag (satellite) sensor if it has been
dropped or sustained an impact. N
JMHIA0009ZZ
• Replace the side air bag (satellite) sensor of deployed SRS front side air bag module and deployed
SRS side curtain air bag module.
INSTALLATION
G
JMHIA0517GB
WARNING: J
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait 3 minutes
or more.
• Before disconnecting the air bag sensor unit harness connector, be sure to disconnect the each har-
ness connector of the air bag module and pre-tensioner seat belt to prevent air bag deployment by K
static electricity and pre-tensioner seat belt operation.
• Never use the air tools or electric tools for servicing.
• When replacing the air bag diagnosis sensor unit, always check with the parts department for the lat- L
est parts information. Installing an incorrect air bag diagnosis sensor unit may or may not cause the
air bag warning lamp to illuminate and may cause incorrect deployment of the supplemental air bags
and seat belt pre-tensioners in a collision resulting in serious personal injury or death.
M
REMOVAL
1. Always check the air bag diagnosis sensor unit ECU discriminated number (identification number) using
CONSULT-III. N
2. Disconnect the each connector of all air bag modules and pre-tensioner seat belts.
3. Remove the instrument lower cover (LH/RH). Refer to IP-20, "Exploded View".
4. Remove the rear foot duct 1 (LH/RH). Refer to VTL-123, "REAR FOOT DUCT 1 : Exploded View". O
5. Remove the instrument stay LH. Refer to IP-20, "Exploded View".
6. Remove the front console bracket. Refer to IP-20, "Exploded View".
P
7. Disconnect the diagnosis sensor unit harness connectors.
8. Remove the fixing bolts, ground bolt, and then remove the diagnosis sensor unit.
CAUTION:
JMHIA0009ZZ
• Replace the diagnosis sensor unit of deployed SRS air bag and deployed SRS front seat belt pre-ten-
sioner.
INSTALLATION
Install air bag diagnosis sensor unit in the reverse order of removal.
CAUTION:
• Never use the old fixing bolts after removal, replace with the new fixing bolts.
• If malfunction is detected by the air bag warning lamp, after repair or replacement of the malfunc-
tioning parts, reset the memory using self-diagnosis or CONSULT-III. Refer to SRC-17, "Diagnosis
Description".
• After the work is completed, check that no system malfunction is detected by air bag warning lamp.
• After replacing the air bag diagnosis sensor unit, confirm using CONSULT-III that the ECU discrimi-
nated number (identification number) of the new replacement air bag sensor unit matches the ECU
discriminated number (identification number) of the replaced (old) air bag diagnosis sensor unit.
NOTE:
If the ECU discriminated number of the new replacement air bag diagnosis sensor unit differs from the ECU
discriminated number of the replaced air bag diagnosis sensor unit, reconfirm the parts information and verify
that the correct air bag diagnosis sensor unit was installed.
For removal and installation procedures, refer to SB-7, "SEAT BELT RETRACTOR : Removal and Installa- B
tion".
SR
PRECAUTION A
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT B
PRE-TENSIONER" INFOID:0000000005716644
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along C
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the “SRS AIR BAG” and
“SEAT BELT” of this Service Manual.
WARNING: D
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer. E
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the “SRS AIR BAG”.
F
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
G
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the SR
ignition ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s)
with a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly
causing serious injury.
• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the I
battery, and wait at least 3 minutes before performing any service.
Service INFOID:0000000005518920
J
• Do not use electrical test equipment to check SRS circuits unless instructed to in this Service Manual.
• Before servicing the SRS, turn ignition switch OFF, disconnect battery negative terminal and wait at least 3
minutes. K
For approximately 3 minutes after the battery negative terminal is removed, it is still possible for the air bag
and seat belt pre-tensioner to deploy. Therefore, do not work on any SRS connectors or wires until at least 3
minutes have elapsed.
L
• Diagnosis sensor unit must always be installed with their arrow marks “⇐” pointing towards the front of the
vehicle for proper operation. Also check diagnosis sensor unit for cracks, deformities or rust before installa-
tion and replace as required.
• The spiral cable must be aligned in the neutral position since its rotations are limited. Do not turn steering M
wheel and column after removal of steering gear.
• Handle air bag module carefully. Always place driver and front passenger air bag modules with the pad side
facing upward and seat mounted front side air bag module standing with the stud bolt side facing down.
N
• Conduct self-diagnosis to check entire SRS for proper functioning after replacing any components.
• After air bag inflates, the front instrument panel assembly should be replaced if damaged.
• Always replace instrument panel pad following front passenger air bag deployment.
O
PREPARATION
PREPARATION
Commercial Service Tools INFOID:0000000005518921
S-NT757
JMKIA3050ZZ
BASIC INSPECTION A
COLLISION DIAGNOSIS
FOR FRONTAL COLLISION
B
FOR FRONTAL COLLISION : When SRS is activated in a collision INFOID:0000000005681361
CAUTION: C
Due to varying models and option levels, not all parts listed in the chart below apply to all vehicles.
WORK PROCEDURE
1. Before performing any of the following steps, ensure that all vehicle body and structural repairs have been D
completed.
2. Replace the diagnosis sensor unit.
3. Remove the front air bag modules, crash zone sensor, bracket and seat belt pre-tensioner assemblies. E
4. Check the SRS components using the table below:
Replace any SRS components showing visible signs of damage. (dents, cracks and deformation, etc.)
5. Install new front air bag modules, crash zone sensor assembly, bracket and seat belt pre-tensioner F
assemblies.
6. Perform self-diagnosis using CONSULT-III or air bag warning lamp. Refer to SRC-186, "Diagnosis
Description" for details. Ensure entire SRS operates properly. G
7. After the work is completed, perform self-diagnosis to check that no malfunction is detected. Refer to
SRC-186, "Diagnosis Description".
SR
SRS INSPECTION (FOR FRONTAL COLLISION)
Part Inspection
I
If the driver air bag has deployed:
Driver air bag module REPLACE
Install with new fasteners.
If the front passenger air bag has deployed:
J
Front passenger air bag module
REPLACE
(if equipped)
Install with new fasteners.
If any of the front air bags or seat belt pre-tensioners* have been activated: K
Crash zone sensor REPLACE the crash zone sensor and bracket with new fasteners.
*: Confirm seat belt pre-tensioner activation using CONSULT-III only.
Seat belt pre-tensioner assem- L
If either the driver or passenger seat belt pre-tensioner* has been activated:
blies
REPLACE all seat belt pre-tensioner assemblies with new fasteners.
(All applicable locations: buckle,
*: Confirm seat belt pre-tensioner activation using CONSULT-III only.
retractor, lap outer)
M
If any of the SRS components have been activated:
Diagnosis sensor unit REPLACE the diagnosis sensor unit.
Install with new fasteners.
1. Visually check steering wheel for deformities. N
2. Check harness (built into steering wheel) and connectors for damage, and terminals for defor-
mities.
Steering wheel 3. Install driver air bag module into the steering wheel to check fit and alignment with the wheel.
4. Check steering wheel for excessive free play. O
5. If no damage is found, reinstall.
6. If damaged − REPLACE.
If the driver front air bag has deployed: P
Spiral cable
REPLACE the spiral cable.
1. Remove passenger seat assembly.
2. Check control unit case for dents, cracks of deformities.
Occupant classification system 3. Check connectors and pressure sensor tube for damage, and terminals for deformities.
(Passenger seat) 4. Check seat frame and cushion pan for dents or deformities.
5. If no damage is found, reinstall seat with new fasteners.
6. If damaged − REPLACE seat cushion assembly with new fasteners.
CAUTION:
Due to varying models and option levels, not all parts listed in the chart below apply to all vehicles.
WORK PROCEDURE
1. Before performing any of the following steps, ensure that all vehicle body and structural repairs have been
completed.
2. Check the SRS components using the table below:
Replace any SRS components showing visible signs of damage. (dents, cracks and deformation, etc.)
3. Perform self-diagnosis using CONSULT-III or air bag warning lamp. Refer to SRC-186, "Diagnosis
Description" for details. Ensure entire SRS operates properly.
4. After the work is completed, perform self-diagnosis to check that no malfunction is detected. Refer to
SRC-186, "Diagnosis Description".
SRS INSPECTION (FOR FRONTAL COLLISION)
Part Inspection
If the driver air bag has NOT been deployed:
1. Remove driver air bag module. Check harness cover and connectors for damage, terminals for
deformities, and harness for binding.
Driver air bag module
2. Install driver air bag module into the steering wheel to check fit and alignment with the wheel.
3. If no damage is found, reinstall with new fasteners.
4. If damaged − REPLACE. Install driver air bag module with new fasteners.
If the front passenger air bag has NOT been deployed:
1. Remove front passenger air bag module. Check harness cover and connectors for damage, ter-
minals for deformities, and harness for binding.
Front passenger air bag module
2. Install front passenger air bag module into the instrument panel to check fit with the instrument
(if equipped)
panel.
3. If no damage is found, reinstall with new fasteners.
4. If damaged − REPLACE. Install front passenger air bag modules with new fasteners.
If the front air bags or seat belt pre-tensioners have NOT been activated:
1. Remove the crash zone sensor. Check harness connectors for damage, terminals for deformi-
ties, and harness for binding.
2. Check for visible signs of damage (dents, cracks, deformation, etc.) of the crash zone sensor
Crash zone sensor
and bracket.
3. Install the crash zone sensor to check fit.
4. If no damage is found, reinstall with new fasteners.
5. If damaged − REPLACE the crash zone sensor and bracket with new fasteners.
If the pre-tensioners have NOT been activated:
1. Remove seat belt pre-tensioners.
Check harness cover and connectors for damage, terminals for deformities, and harness for
binding.
Seat belt pre-tensioner assem-
2. Check belts for damage and anchors for loose mounting.
blies
3. Check retractor for smooth operation.
(All applicable locations: buckle,
4. Check seat belt adjuster for damage.
retractor, lap outer)
5. Check for deformities of the center pillar inner.
6. If the center pillar inner has no damage, REPLACE the seat belt pre-tensioner assembly.
7. If no damage is found, reinstall seat belt pre-tensioner assembly.
8. If damaged − REPLACE. Install the seat belt pre-tensioners with new fasteners.
CAUTION: L
Due to varying models and option levels, not all parts listed in the chart below apply to all vehicles.
WORK PROCEDURE
M
1. Before performing any of the following steps, ensure that all vehicle body and structural repairs have been
completed.
2. Replace the following components:
• Front seat back assembly (on the side on which side air bag is activated) N
• Door finisher (on the side on which door-mounted curtain air bag is activated)
• Pop-up roll bar assemblies and pop-up roll bar covers
• Side air bag (satellite) sensor LH/RH (on the side on which side air bag is activated) O
• Diagnosis sensor unit
• Seat belt pre-tensioner assemblies
3. Check the SRS components and the related parts using the following table. P
Replace any SRS components and the related parts showing visible signs of damage. (dents, cracks,
deformation, etc.)
4. Perform self-diagnosis using CONSULT-III and “AIR BAG” warning lamp. Refer to SRC-186, "Diagnosis
Description" for details. Make sure entire SRS operates properly.
5. After the work is completed, perform self-diagnosis to check that no malfunction is detected. Refer to
SRC-186, "Diagnosis Description".
Part Inspection
If the side curtain air bag LH has deployed:
Side curtain air bag module LH REPLACE the side curtain air bag module LH.
Install with new fasteners.
If the side curtain air bag RH has deployed:
Side curtain air bag module RH REPLACE the side curtain air bag module RH.
Install with new fasteners.
If the front side air bag LH has deployed:
Front side air bag module LH
REPLACE front seatback assembly LH.
If the front side air bag RH has deployed:
Front side air bag module RH
REPLACE front seatback assembly RH.
Side air bag (satellite) sensor If any of the SRS components have deployed:
(LH or RH) REPLACE the side air bag (satellite) sensor on the collision side with new fasteners.
If any of the SRS components have deployed:
Diagnosis sensor unit
REPLACE the diagnosis sensor unit with new fasteners.
Seat belt pre-tensioner assem-
If either the driver or passenger seat belt pre-tensioner* has been activated:
blies
REPLACE all seat belt pre-tensioner assemblies with new fasteners.
(All applicable locations: buckle,
*: Confirm seat belt pre-tensioner activation using CONSULT-III only.
retractor, lap outer)
1. Check the center inner pillar on the collision side for damage (dents, cracks, deformation, etc.).
Center inner pillar
2. If damaged − REPAIR the center inner pillar.
1. Check for visible signs of damage (dents, cracks, deformation, etc.) of the interior trim on the
Trim/headlining collision side.
2. If damaged − REPLACE the damaged trim parts.
If the door-mounted curtain air bag module LH has deployed:
Door-mounted curtain air bag
REPLACE the door finisher LH and door-mounted curtain air bag module.
module LH
Install with new fasteners.
If the door-mounted curtain air bag module RH has deployed:
Door-mounted curtain air bag
REPLACE the door finisher RH and door-mounted curtain air bag module.
module RH
Install with new fasteners.
If the pop-up roll bar has deployed:
Pop-up roll bar assemblies REPLACE pop-up roll bar assemblies and pop-up roll bar covers.
Install with new fasteners.
FOR SIDE AND ROLLOVER COLLISION : When SRS is not activated in a collision
INFOID:0000000005681364
CAUTION:
Due to varying models and option levels, not all parts listed in the chart below apply to all vehicles.
WORK PROCEDURE
1. Before performing any of the following steps, ensure that all vehicle body and structural repairs have been
completed.
2. Check the SRS components and the related parts using the following table.
• If the front seat back assembly is damaged, the front seat back assembly must be replaced.
• If the door finisher assembly is damaged, the door finisher assembly and door-mounted curtain air bag
module must be replaced.
3. Perform self-diagnosis using CONSULT-III and “AIR BAG” warning lamp. Refer to SRC-186, "Diagnosis
Description" for details. Make sure entire SRS operates properly.
4. After the work is completed, perform self-diagnosis to check that no malfunction is detected. Refer to
SRC-186, "Diagnosis Description".
SRS INSPECTION (FOR SIDE AND ROLLOVER COLLISION)
JMHIA0503GB
SR
1. Steering wheel 2. Driver air bag module 3. Side lid (LH/RH)
4. TORX bolt (LH/RH)
Refer to GI-4, "Components" for symbols in the figure. I
J
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait 3 minutes
or more.
• Always work from the side of air bag module. Never work in front of it. K
• Never use the air tools or electric tools for servicing.
REMOVAL
L
1. Remove the side lids (LH/RH).
2. Remove the TORX bolts (LH/RH) from the steering wheel (1)
lower side using TORX bit (A). M
JMHIA0265ZZ
P
3. Pull out the driver air bag module.
PHIA0953J
: Upward
JMHIA0504ZZ
JMHIA0009ZZ
• Never insert any foreign objects (screwdriver, etc.) into the driver air bag module.
• Never disassemble the driver air bag module.
• Never expose the driver air bag module to temperatures exceeding 90 °C (194 °F).
• Never allow oil, grease, detergent, or water to come in contact with the driver air bag module.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• Never use the old TORX bolts after removal, replace with the new bolts.
• Fix the driver air bag harness to the harness fixing hook (A).
JMHIA0505ZZ
SR
JMHIA0506ZZ
1. Steering column cover (upper) 2. Spiral cable 3. Steering column cover (lower)
4. Steering column assembly
A. Driver air bag harness connector
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait 3 minutes
or more.
• Never use the air tools or electric tools for servicing.
REMOVAL
1. Remove the driver air bag module. Refer to SR-37, "Removal and Installation".
2. Remove the steering wheel. Refer to ST-17, "Removal and Installation".
3. Remove the steering column cover (upper/lower). Refer to IP-12, "Exploded View".
4. Disconnect the spiral cable body side harness connectors (A).
NOTE:
Disconnect the spiral cable body side harness connectors after
removing the spiral cable.
JMHIA0507ZZ
JMHIA0508ZZ
D
7. Pull out forward the spiral cable.
CAUTION:
• Never impact the spiral cable. E
• Never impact the spiral cable by dropping, etc. Replace the
spiral cable if it has been dropped or sustained an impact.
F
JMHIA0009ZZ SR
JMHIA0013ZZ
G
JMHIA0509GB
I
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait 3 minutes
or more. J
• Always work from the side of air bag module. Never work in front of it.
• Never use the air tools or electric tools for servicing.
REMOVAL K
1. Remove the glove box lid assembly. Refer to IP-13, "Removal and Installation".
2. Remove the Instrument lower assist panel. Refer to IP-13, "Removal and Installation".
3. Disconnect the front passenger air bag harness connector (A). L
4. Remove the front passenger air bag module fixing bolt (B).
NOTE:
The figure shows the installed front passenger air bag module. M
(Under view of the module installed without glove box cover.)
JMHIA0510ZZ
O
5. Remove the instrument panel assembly (1). Refer to IP-13, "Removal and Installation".
P
JMHIA0511ZZ
CAUTION:
• Always place the front passenger air bag module with pad
side facing upward.
: Upward
JMHIA0512ZZ
JMHIA0009ZZ
• Never insert any foreign objects (screwdriver, etc.) into front passenger air bag module.
• Never disassembly the front passenger air bag module.
• Never expose the front passenger air bag module to temperatures exceeding 90 °C (194 °F).
• Never allow oil, grease, detergent, or water to come in contact with the front passenger air bag mod-
ule.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• Never use the old fixing bolts after removal, replace with the new bolts.
• Never damage the harness while installing.
• If malfunction is detected by the air bag warning lamp, after repair or replacement of the malfunc-
tioning parts, reset the memory using self-diagnosis or CONSULT-III. Refer to SRC-17, "Diagnosis
Description".
• After the work is completed, check that no system malfunction is detected by air bag warning lamp.
G
JMHIA0514GB
1. Seatback flame 2. Seat cushion flame 3. Front side air bag module
A. Front side air bag harness connector SR
Refer to GI-4, "Components" for symbols in the figure.
REMOVAL
WARNING: J
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait at least 3
minutes.
• Always work from the rear of the front side air bag module. K
• Never use the air tools or electric tools for servicing.
1. Remove the front seat. Refer to SE-112, "Removal and Installation".
2. Remove the seatback board. Refer to SE-105, "Exploded View". L
3. Remove the front side air bag module fixing nuts, and/or harness connector.
4. Remove the front side air bag module.
CAUTION: M
• Always place the front side air bag module with pad side fac-
ing upward.
N
: Upward
P
JMHIA0274ZZ
JMHIA0009ZZ
• Never insert any foreign objects (screwdriver, etc.) into front side air bag module.
• Never disassemble the front side air bag module.
• Never expose the front side air bag module to temperatures exceeding 90 °C (194 °F).
• Never allow oil, grease, detergent, or water to come in contact with the front side air bag module.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• Never use the old fixing nuts after removal, replace with the new nuts.
• If malfunction is detected by the air bag warning lamp, after repair or replacement of the malfunc-
tioning parts, reset the memory using self-diagnosis or CONSULT-III. Refer to SRC-186, "Diagnosis
Description".
• After the work is completed, check that no malfunctioning system is detected by air bag warning
lamp.
G
JMHIA0513GB
1. Side curtain air bag inflator 2. Side curtain air bag 3. Strap
A. Side curtain air bag harness connec- B. Ground bolt SR
tor
Refer to GI-4, "Components" for symbols in the figure.
I
Removal and Installation INFOID:0000000005518931
WARNING: J
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait 3 minutes
or more.
• Never use air tools or electric tools for servicing.
K
REMOVAL
1. Remove the headlining.
• Normal roof models: Refer to INT-27, "NORMAL ROOF : Removal and Installation". L
• Sunroof models: Refer to INT-30, "SUNROOF : Removal and Installation".
2. Remove the side curtain air bag harness connector.
CAUTION:
M
• For installing/removing the side curtain air bag harness
connector, insert thin screwdriver wrapped in tape into
notch, lift lock and remove the connector.
• Install the connector with lock raised, and push lock into N
the connector.
• After installing the connector, check that the lock is
pushed securely into it. O
P
PHIA0953J
3. Remove the fixing bolts, and then remove the side curtain air bag module.
CAUTION:
JMHIA0009ZZ
• Never insert any foreign objects (screwdriver, etc.) into the side curtain air bag module.
• Never disassemble the side curtain air bag module.
• Never expose the side curtain air bag module to temperatures exceeding 90 °C (194 °F).
• Never allow oil, grease, detergent, or water to come in contact with the side curtain air bag module.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• If malfunction is detected by the air bag warning lamp, after repair or replacement of the malfunc-
tioning parts, reset the memory using self-diagnosis or CONSULT-III. Refer to SRC-17, "Diagnosis
Description".
• After the work is completed, check that no system malfunction is detected by air bag warning lamp.
G
JMHIA0515GB
WARNING: J
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait 3 minutes
or more.
• Never use air tools or electric tools for servicing.
K
REMOVAL
1. Remove the radiator cover grill (RH). Refer to EM-31, "Exploded View".
2. Remove the air duct (inlet). Refer to EM-31, "Exploded View". L
3. Remove the crash zone sensor fixing nuts.
4. Disconnect the crash zone sensor harness connector, and then remove the crash zone sensor.
CAUTION: M
• Never impact the crash zone sensor.
• Replace the crash zone sensor if it has been dropped or sus-
tained an impact. N
P
JMHIA0009ZZ
• Replace the crash zone sensor of deployed SRS driver air bag and deployed SRS front passenger air
bag.
INSTALLATION
Install in the reverse order of removal.
G
JMHIA0516GB
WARNING: J
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait 3 minutes
or more.
• Never use the air tools or electric tools for servicing.
K
REMOVAL
1. Remove the front seat belt. Refer to SB-7, "SEAT BELT RETRACTOR : Removal and Installation".
2. Remove the side air bag (satellite) sensor fixing nuts. L
3. Disconnect the side air bag (satellite) sensor harness connector, and then remove the side air bag (satel-
lite) sensor.
M
CAUTION:
• Never impact the side air bag (satellite) sensor.
• Replace the side air bag (satellite) sensor if it has been
dropped or sustained an impact. N
JMHIA0009ZZ
• Replace the side air bag (satellite) sensor of deployed SRS front side air bag module and deployed
SRS side curtain air bag module.
INSTALLATION
G
JMHIA0517GB
WARNING: J
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait 3 minutes
or more.
• Before disconnecting the air bag sensor unit harness connector, be sure to disconnect the each har-
ness connector of the air bag module and pre-tensioner seat belt to prevent air bag deployment by K
static electricity and pre-tensioner seat belt operation.
• Never use the air tools or electric tools for servicing.
• When replacing the air bag diagnosis sensor unit, always check with the parts department for the lat- L
est parts information. Installing an incorrect air bag diagnosis sensor unit may or may not cause the
air bag warning lamp to illuminate and may cause incorrect deployment of the supplemental air bags
and seat belt pre-tensioners in a collision resulting in serious personal injury or death.
M
REMOVAL
1. Always check the air bag diagnosis sensor unit ECU discriminated number (identification number) using
CONSULT-III. N
2. Disconnect the each connector of all air bag modules and pre-tensioner seat belts.
3. Remove the instrument lower cover (LH/RH). Refer to IP-20, "Exploded View".
4. Remove the rear foot duct 1 (LH/RH). Refer to VTL-123, "REAR FOOT DUCT 1 : Exploded View". O
5. Remove the instrument stay LH. Refer to IP-20, "Exploded View".
6. Remove the front console bracket. Refer to IP-20, "Exploded View".
P
7. Disconnect the diagnosis sensor unit harness connectors.
8. Remove the fixing bolts, ground bolt, and then remove the diagnosis sensor unit.
CAUTION:
JMHIA0009ZZ
• Replace the diagnosis sensor unit of deployed SRS air bag and deployed SRS front seat belt pre-ten-
sioner.
INSTALLATION
Install air bag diagnosis sensor unit in the reverse order of removal.
CAUTION:
• Never use the old fixing bolts after removal, replace with the new fixing bolts.
• If malfunction is detected by the air bag warning lamp, after repair or replacement of the malfunc-
tioning parts, reset the memory using self-diagnosis or CONSULT-III. Refer to SRC-17, "Diagnosis
Description".
• After the work is completed, check that no system malfunction is detected by air bag warning lamp.
• After replacing the air bag diagnosis sensor unit, confirm using CONSULT-III that the ECU discrimi-
nated number (identification number) of the new replacement air bag sensor unit matches the ECU
discriminated number (identification number) of the replaced (old) air bag diagnosis sensor unit.
NOTE:
If the ECU discriminated number of the new replacement air bag diagnosis sensor unit differs from the ECU
discriminated number of the replaced air bag diagnosis sensor unit, reconfirm the parts information and verify
that the correct air bag diagnosis sensor unit was installed.
For removal and installation procedures, refer to SB-7, "SEAT BELT RETRACTOR : Removal and Installa- B
tion".
SR