GO2 GSM/SMS

Alarm System
Printed in China
PA: GO2-UM-EN-V1.2 User Manual
Foreword Contents

Dear users, In the Box.......................................................................................................................................... 1~2

Thank you for choosing our product. This product is a totally D.I.Y. wireless home Included Accessories........................................................................................................................2
security solution. It features automatic connection to various accessories, putting your How It Works..........................................................................................................................................3
home under all-round protection. To experience this wonderful product, please follow Accessories....................................................................................................................................... 4~9
the instructions in the user manual. Remote Control.................................................................................................................................4
Door/Window Contact....................................................................................................................5
PIR Motion Detector.........................................................................................................................6
Disclaimer Zone Mode of Sensor......................................................................................................................8
Getting Started.............................................................................................................................. 9~12
Step 1. Insert SIM Card....................................................................................................................9
Dear users, Step 2. Download the App.............................................................................................................9
Step 3. Add an Account............................................................................................................... 10
We have reviewed this manual thoroughly in order that it will be an easy to use guide
Step 4. Be Familiar with the Alarm System............................................................................... 10
to this product. All statements, technical information, recommendations in this manual
are believed reliable, but the accuracy and completeness thereof are not guaranteed or Step 5. System Settings................................................................................................................ 11
warranted. Setting through SMS..................................................................................................................13~14
Other SMS Notifications................................................................................................................ 14
The specifications and information regarding the products in this document are subject Installation......................................................................................................................................15~18
to change without notice. Sensor Placement........................................................................................................................... 15
Installation Mode............................................................................................................................ 16
Photocopy, copy, reproduction, translation to any language, modification, storage in a
Placing the Control Panel............................................................................................................. 17
retrieval system or retransmission, in any form or by any means, electronic, mechanical
or otherwise, is strictly prohibited without prior written permission. Mounting the Door/Window Contact....................................................................................... 17
Mounting the PIR Motion Detector............................................................................................ 18
In no event we are liable for any indirect, special, incidental, or consequential damages, Pairing/Deleting Accessory.......................................................................................................19~20
including, without limitation, lost profits or loss or damage to data arising out of the use Pairing New Remote Control and Sensor................................................................................. 19
or inability to use this document, even if the product has been advised of the possibility Pairing New Wireless Siren........................................................................................................... 20
of such damages. Deleting Sensors............................................................................................................................. 20
Deleting Wireless Siren.................................................................................................................. 20
Reload the Batteries of Accesories................................................................................................. 21
Arm & Disarm by Free Phone Call................................................................................................. 22
Restore to Factory Settings.............................................................................................................. 22
Specifications................................................................................................................................23~24
Control Panel................................................................................................................................... 23
Remote Control............................................................................................................................... 23
Door/Window Contact.................................................................................................................. 24
PIR Motion Detector...................................................................................................................... 24
 In the Box System Status

Arm: Press [ ] to arm your system. Now all the sensors are on guarding.
Disarm: Enter the password (default setting: 1234) and press [ ] to disarm your
system. Now your system stops handling alarm signal from sensors (except these
GSM Signal Indicator sensors in 24-H zone).
Voice Memo Indicator Home Arm: Press [ ] to part arm your system. Now your system only stops handling
alarm signal from home mode zone sensors, which enables users to move freely at
Call home.

Included Accessories
Record Voice Memo
This alarm system has the following accessories included in the box.

Arm Disarm Home Arm

Blinks once per second: Searching network.

Blinks once per 3 seconds: Connected with network.
PIR Motion Detector x 1
Blinking: There is a new voice memo.
Enter a phone number and press this call button to make a call.
Press and hold it for 3 seconds to leave a 10-second voice memo.
Press once to listen to a new voice memo or replay.

Door/Window Contact x 1
SIM

SIM
SIM Card Slot

Power On/Off
Adapter Jack

Remote Control x 2 AC Adapter x 1 User Manual x 1

1 2
 How It Works Accessories

The control panel will receive an alarm signal when a sensor is triggered, it will hoot and Remote Control
inform users by sending SMS and making calls.
Status Indicator

Arm Disarm

SOS
Home Arm SOS

Button System Status

Press once to arm. The siren beeps once to confirm the system is armed.

When you receive a phone call from the control panel, you will hear your pre-recorded
Press once to disarm. The siren beeps twice confirm the system is disarmed.
alarm voice message first, and then you can remotely control the system by pressing the
numbers on your phone keyboard. Press once to home arm. After 3 seconds, the siren beeps once to confirm the
system is in home mode.
Operation Function Note: The control panel only stops handling alarm signal from the home mode
zone sensor, which enables users to move freely at home.
0 Disarm
The control panel will hoot on-site with indicator flashing, and users will receive
1 Arm SMS and calls.
Press the [ ] button. After the indicator on the remote control blinks once,
6 Turn off siren
press [ ] button within 3 seconds to mutely arm the system.
9 Turn on siren Press the [ ] button. After the indicator on the remote control blinks once,
press [ ] button within 3 seconds to mutely disarm the system.
* Two-way talk

# Hang up

You can record an alarm voice message by the following steps:

Enter disarm password (default setting: 1234), and then press [ ] and [ ] button to leave a
10-second alarm message.

Distinction
Voice memo: Message is recorded to your family members.
Alarm voice message: Message is played when you pick up an emergency call.

3 4
 Door/Window Contact PIR Motion Detector
The contact contains a transmitter and a magnet. It can be mounted on doors, windows The detector adopts digital dual-core fuzzy logic control processing technology and
and any other objects that can be opened or closed. When the transmitter and magnet intelligent analyze algorithm. When human bodys infrared spectrum is detected, it will
are separated over 2 cm, the contact will send a signal to the control panel to trigger an send alarm signal to the control panel.
alarm. The detector features pet immunity for animals up to 25kgs.

Overview Overview
Status Indicator 1. Detection Lens
2. Status Indicator

Battery 3. Test Button

Tamper Switch 5
4. Bracket Slot
Transmitter Magnet 5. Double-sided Tape Stick Place
Zone Setting

Status Indication
Status Indicator
Blinks continuously: Motion detector performs a self-test.
Blinks once: Door/window is opened.
Blinks once: Motion is detected.
Blinks once per 3 seconds: Low battery, please replace battery.
Blinks twice: Motion detector has exited testing mode, and goes to power saving mode.
Blinks once per 3 seconds: Low battery, please replace battery.
Note: When tamper switch is pressed, the system will alarm immediately.
Tamper Switch
Infrared
PCB LayoutSensors

Zone Setting
Status Indicator
Tamper Switch
Infrared Sensors

Zone Setting
Status Indicator

Tamper Switch: When the tamper switch is pressed, system will alarm immediately.
Infrared Sensors: The infrared sensors detect movement, and please make sure they are
always clean.

5 6
 Working Mode Pet-Immune Function
Testing Mode This sensor adopts a special design to improve detection accuracy. Pets less than 25kgs
will not trigger the alarm.
After a 1 minute self-test, the detector enters a testing mode. It detects once in every 10
seconds and emits alarm signal when motion is detected. This will last for 3 minutes and
then switches into power saving mode.

Note: You can press the test button to enter testing mode too. 2-2.2m

Power Saving Mode

1m 8m

If the PIR motion detector detects movements twice in 3 minutes, it automatically goes
into asleep state. If there is no movement detected in next 3 minutes, it will switch from
asleep state to arm. During the 3 minutes, the detector wont be active and send any
signals to the control panel. As long as there is a movement detected within 3 minutes,
the duration of power saving mode will be extended.
2-2.2m

Case 1: Case 2:
Initial start and then arm. Press the test button and then arm.

3 minutes later

Sleep after detecting human movement twice. Zone Mode of Sensor

Sensors can be placed in different zones for different requirements. Four different zones
No human movement within 3 minutes
can be selected:
Switch from sleep to arm. Normal zone: In arm or home arm state, the detectors set to normal zone work
normally. Once intrusion is detected, the detectors trigger an alarm.
Home zone: When system is in home arm state, the detectors set to home zone are
Detection Range disarmed. The detectors set to other zones are armed. That is, partial arm.
Single delay zone: Sensors set to this zone will alarm at the specified time (which can set
by yourself ) after being triggered.
24-H zone: The detector set to 24-H zone trigger an alarm immediately when detecting
2.2m intrusion,no matter the system is armed or disarmed.
Top view
Sensors in This Kit Zone Mode(Default Setting)

Door/Window Contact Normal Zone

Side view PIR Motion Detector Home Mode Zone

You can set zone by changing the jumpers in detector. After the setting, detector can
work in corresponding mode. It must be paired to the control panel again.

7 8
 How to set: Step 3. Add an Account
Open the rear cover of the detector; change the array of jumpers on the zone setting to
the corresponding position as below (Mind the direction of D0-D3):

Home Mode Zone Normal Zone Signal Delay Zone 24-H Zone

Getting Started
Step 4. Be Familiar with the Alarm System
Step 1. Insert SIM Card
Now you can tap [ ], [ ], [ ] to arm/disarm/home arm your system remotely.
Before inserting the SIM card, please perform the following steps: Tap [ ] and app will skip to messages interface automatically. After sending the SMS,
1. Make sure the alarm system is powered off.
you will receive a phone call from the control panel to leave a 10-second voice memo.
2. IMPORTANT: Remove the (default) code permanently from the SIM card.
3. Turn off the voice mail function if it is enabled. Tap [ ] and app will skip to messages interface automatically. After sending the SMS,
4. Insert the SIM card into the SIM card slot; wait until the GSM indicator starts blinking you will receive a phone call from the control panel to start a two-way talk.
once every 3 seconds; it means the network is connected.

SIM card requirement: 2G GSM SIM card with calling, SMS and caller display functions.

Step 2. Download the App

Download the App by searching keywords GO2 Alarm in the App Store or Google
Play, and then create your own account.

GO2 Alarm

9 10
 Step 5. System Settings Exit & Entry Delay Time
If you don't want to carry remote controls, you can set the exit or entry delay. Suppose
entry delay was set at 30 seconds, the system will allow you 30 seconds to disarm the
system before alarming. Suppose exit delay was set at 35 seconds, the system will allow
you 35 seconds to leave before the system is armed. The "beep" is heard in every
second to remind you to leave. The pace of reminding sound will speed up in last 15
seconds. Thus leaves you enough time to leave home without triggering the system.

Single Zone Delay Time

(To apply this function, you should change the zone mode of the sensor to single delay
zone first. Please refer to Zone Mode of Sensor on page 9).
After the time setup, the single delay zone sensor will delay to alarm when it is triggered.

Comparison
Store Emergency Numbers & SMS Numbers
For example: The exit & delay time is set at 30 seconds; single zone delay time is set at
Emergency numbers are the phone numbers that will receive calls from the control
40 seconds.
panel when the alarm goes off.
SMS numbers are the phone numbers that will receive alarm SMS from the control panel
Sensor Arm Alarm
when the alarm goes off.
Normal and home mode zone Delay 30s to arm Delay 30s to alarm
IMPORTANT: After phone numbers are stored, only those numbers can modify the system
settings. Commands from unauthorized phone numbers will be rejected. Single delay zone Delay 30s to arm Delay 40s to alarm
Once an alarm is triggered, the control panel will dial the emergency numbers 3 rounds at most,
if a phone is picked up with operation on phone button, the system will stop dialing. 24-H zone Always in arm state Alarm immediately

Store Speed Dial Number Disarm Password

After the number is stored, you can dial this number immediately by pressing [ ] The default disarm password is 1234. It is suggested to change the passcode for
button once on the control panel. safety.

Change Zone Name

10 remote controls and 50 sensors could be extended and the names of sensors are
able to be edited.
This function aims at guiding users to identify the invasion location quickly by changing
the sensor name. Their sequence in naming follows pairing order. For example, the first
paired sensor is by default set to zone 1; the second paired sensor is by default assigned
to zone 2, etc. In case of emergency, if you did not change the sensor name, this control
panel will send SMS with zone number to user (e.g. Zone 1 Alarm).

11 12
 Setting through SMS For example:
1. Send 5 to the SIM card number of the control panel.

If you use a non-smart phone, you can set your system by sending the related SMS
command codes to the SIM card in the control panel. 5
Item SMS Command Code
SMS menu ?, ??, ??? 2. You will receive a menu SMS from the control panel.
System setting inquiry 00
TEL:
Disarm 0
1.
Arm 1 2.
Home arm 2 3.
Two-way talk 3 4.

Call back to leave a 10-second voice memo 4 5.

Store emergency telephone numbers 5

Store emergency SMS numbers 6 3. Copy and edit the menu message, and then send it back.
Store speed dial number 8
Change zone name 901~950 5 5

Set exit & entry delay time 11 Copy More...

Set alarm volume and ringing time 12

Change disarm passcode 13 Send

Paste

Set single zone delay time 14 Text Message Send Text Message Send

4. You will receive a SMS for confirmation from the control panel.

Other SMS Notifications

You will receive SMS for reminding you:
1. When the control panel and sensors are in low battery, the 1st stored phone number
will receive a SMS.
2. When the AC power of control panel fails or restores, the 1st stored phone number
will receive a SMS.
3. When the tamper switch of sensors trigger an alarm, all the stored phone numbers
will receive a SMS.

13 14
 Installation Installation Mode
There are possibilities to trigger an alarm when mounting the sensors. You can press the
[ ] button for 3 times on the control panel to enter the 10-minute installation mode.
Sensor Placement During this period, system only beeps 3 times when the sensor is triggered. You can also
press [ ] button on the control panel to exit this mode.
The alarm system is most effective with well-placed sensors. Determine which area you
want to guard and what kind of detectors should be used. The following picture is the
potential places shown for different types of detectors. You can refer it to choose an Placing the control panel
ideal place.
There are two installation methods for users. The one is placing the control panel on the
desk; the other one is mounting it on wall by using the supplied screw kit. Please choose
an ideal place and suitable method to mount your control panel.

A. Alarm panel B. Remote control C. Wireless Siren

1. Front door Magnet contact
2. Living area PIR motion detector
3. Window: living area Magnet contact
4. Window: living area Magnet contact
5. Terrace door Magnet contact
6. Window Magnet contact
7. Bedroom PIR motion detector
8. Kitchen Gas detector

15 16
 Mounting the Door/Window Contact Mounting the PIR Motion Detector
Make sure the contact works properly before installation. Important: Avoid installing the motion detector directly towards windows and near heat
sources, such as heat extraction units, air-condition, micro-wave oven, refrigerator etc;
Step 1: Choose a suitable installation location
Avoid placing two motion detectors in the opposite of each other; Dont place them in
It can be installed on doors, windows or any other objects that can be opened or closed.
each others detection range.
If it is applied to metal doors, please place a spacer under the transmitter and magnet.
Step 2: Secure the contact with the supplied sticker ON

Make sure the gap marks on the side of transmitter and magnet are closed to each
other and within the range of 1cm. As long as the space between transmitter and
ON

ON

magnet is over 2cm; The status indicator on the transmitter will blink once.

Step 1: The ideal mounting height of the motion detector is 2-2.2 meters from the floor.
It is suggested to mount it at the corner of the wall by using the supplied 3M sticker.

2-2.2m

2-2.2m
2-2.2m

Ground
Ground
Ground

Step 2: Press the test button twice and walk from left to right in the room. The status
indicator will blink once when motion is detected.

Note: This PIR motion detector can also be mounted at special location by using the supplied
bracket and screw kits.

17 18
 Pairing/Deleting Accessory Pairing New Wireless Siren
Siren is sold separately.
1. Make sure the siren enters pairing state (please refer to relevant user manual).
The included accessories have been paired with the control panel by default, if you want 2. Press [ ] or [ ] on the control panel to send out a pairing signal to the siren.
to pair new accessories, please follow these instructions: When a beep is heard from the siren, the siren is paired successfully. If two beeps are
heard, the siren has already been paired before.
Pairing New Remote Control and Sensor If a wireless siren is paired, you can turn on or off the arm/disarm tone by sending 63701 or
Enter the disarm password (default: 1234); then press the [ ] button on the control 63700 to the control panel (The default setting is off ).
panel and trigger the sensors once.

Deleting Sensors
Press any button on
Send SMS with content 21 to the control panel, then you will receive an SMS to
the remote control
confirm the successful deletion of sensors.
Send SMS with content 23 to the control panel, then you will receive an SMS to
confirm the successful deletion of remote controls.

Press the test button

more than twice Deleting Wireless Siren
Press and hold the pair button of the wireless siren; the deletion is succeeded when two
beeps are heard from the wireless siren.
Separate the
transmitter and the
magnet over 2cm

When a beep is heard from the control panel, the sensor is paired successfully. If two
beeps are heard, the sensor has already been paired before.

Note: To pair other sensors, please refer to the related user manuals.

19 20
 Reload the Batteries of Accessories Arm & Disarm by Free Phone Call

Remote Control Arming the alarm system can be done by calling the SIM card No. in the control panel.
Hanging up the call after you hear the dialing tone, and then you will be called by the
control panel; do not answer the phone call and the system will be armed.

Disarming the alarm system can be done by calling the SIM card No. in the control
panel. Do not hang up until the system disconnected by itself. The alarm system will not
call you back and the system is disarmed.

Loose the screw Open the case and change the battery
Restore to Factory Settings
Door/Windor Contact
Send text 0000 to the control panel; the system will be restored to factory settings, but
the paired sensors remain working.

Open the case and change the battery

PIR Motion Detector

Loose the screw Open the case and change the battery

21 22
 Specifications Door/Window Contact
PowerSupply DC 3V (CR2032 lithium battery x 2pcs)

Control Panel Static Current <5 uA

AlarmCurrent <9 mA
PowerSupply DC12V500 mA
Transmitting Distance <80 m (open area/no interference)
Battery 3.7V 600 mAh Li-ion Battery
Radio Frequency 315 MHz or 433.92 MHz
GSM Frequency 850/900/1800/1900 MHz
HousingMaterial ABS Plastic
StandbyCurrent <56 mA
OperatingCondition Temperature -10C~+55C
AlarmCurrent <270 mA
Relative Humidity <80% (non-condensing)
InternalSiren 90 dB
Transmitter Dimensions 71 x 31.5 x 15 mm (L x W x H)
ExpandableAccessories 10RemoteControls,50Sensors
Magnet Dimensions 71 x 12.5 x 15 mm (L x W x H)
RadioFrequency 315 MHz or 433.92 MHz
HousingMaterial ABSPlastic
OperatingCondition Temperature -10C~+55C PIR Motion Detector
RelativeHumidity <80% (non-condensing) PowerSupply DC 3V (AA 1.5V LR6 battery x 2 pcs)
Control Panel Dimensions 125 x 150 x 30 mm (L x W x H) Static Current <50 uA
Bracket Dimensions 87.5 x 81.5 x 12 mm (L x W x H) AlarmCurrent <9.5 mA
Detection Scope 8m/110
Transmitting Distance <80 m (open area/no interference)
Remote Control
Radio Frequency 315 MHz or 433.92 MHz
PowerSupply DC 3V (CR2025 lithium battery x 1pc) HousingMaterial ABS Plastic
Transmit Current <7 mA OperationCondition Temperature -10C~+55C
Transmitting Distance <80 m (open area/no interference) Relative Humidity <80% (non-condensing)
Radio Frequency 315 MHz or 433.92 MHz Detector Dimensions 100 x 59 x 43 mm (L x W x H)
HousingMaterial ABS Plastic Bracket Dimensions 52 x 30 x 26.5 mm (L x W x H)
OperatingCondition Temperature -10C~+55C
Relative Humidity <80% (non-condensing)
Dimensions 53 x 31 x 11 mm (L x W x H)

23 24