C067

SPECIFICATION FOR LOW-ALLOY STEEL
ELECTRODES FOR SHIELDED METAL ARC

WELDING
SFA-5.5
(Identical with AWS Specification A5.5-96.)
1. Scope 4. Certification
This specification prescribes requirements for the By affixing the AWS specification and classification
classification of low-alloy steel electrodes for shielded designations to the packaging, or the classification to
metal arc welding of carbon and low-alloy steels. the product, the manufacturer certifies that the product
These electrodes include steel alloys in which no single meets the requirements of this specification.2
alloying element exceeds 10.5 percent.
PART A GENERAL REQUIREMENTS 5. Units of Measure and Rounding-Off

2. Classification Procedure
2.1 The welding electrodes covered by this specifica- 5.1 U.S. customary units are the standard units of
tion are classified according to the following: measure in this specification. The SI units are given
as equivalent values to the U.S. customary units. The
(a) Type of current (Table 1)
standard sizes and dimensions in the two systems are
(b) Type of covering (Table 1)
not identical and for this reason conversion from a
(c) Welding position (Table 1)
standard size or dimension in one system will not
(d) Chemical composition of the weld metal (Table 2) always coincide with a standard size or dimension in
(e) Mechanical properties of the weld metal in the the other. Suitable conversions, encompassing standard
as-welded or postweld heat-treated condition (Tables 3 sizes of both, can be made, however, if appropriate
and 4) tolerances are applied in each case.
2.2 Material classified under one classification shall
not be classified under any other classification in this 5.2 For the purpose of determining conformance with
specification. this specification, an observed or calculated value shall
be rounded to the nearest unit in the last right-hand
place of figures used in expressing the limiting value
3. Acceptance in accordance with the rounding-off rules given in
ASTM E29, Standard Practice for Using Significant
Acceptance1 of the welding electrode shall be in
Digits in Test Data to Determine Conformance with
accordance with the provisions of the ANSI/AWS
Specifications.
A5.01, Filler Metal Procurement Guidelines.
1 2
See Section A3, Acceptance (in the Appendix), for further informa- See Section A4, Certification (in the Annex), for further information
tion concerning acceptance, testing of the material shipped, and concerning certification and the testing called for to meet this
ANSI/AWS A5.01, Filler Metal Procurement Guidelines. requirement.
99
SFA-5.5 2001 SECTION II
TABLE 1
ELECTRODE CLASSIFICATION
AWS Welding Positions Type of
Classificationa Type of Covering for Classificationb Currentc
E7010-X High-cellulose sodium F,V,OH,H DCEP
E7011-X High-cellulose potassium F,V,OH,H ac or DCEP
E7015-Xd,e Low-hydrogen sodium F,V,OH,H DCEP
E7016-Xd,e Low-hydrogen potassium F,V,OH,H ac or DCEP
E7018-Xd,e Low-hydrogen potassium, iron powder F,V,OH,H ac or DCEP
E7020-X High-iron oxide H-fillets
F
ac or DCEN
ac, DCEP or DCEN
E7027-X High-iron oxide, iron powder H-fillets
F
ac or DCEN
ac, DCEP or DCEN
E8010-X High-cellulose sodium F,V,OH,H DCEP
E8011-G High-cellulose potassium F,V,OH,H ac or DCEP
E8013-G High-titania potassium F,V,OH,H ac, DCEP or DCEN
E9010-G High-cellulose sodium F,V,OH,H DCEP
E9018Md,e Iron-powder, low hydrogen F,V,OH,H DCEP
E11015-Gd,e Low-hydrogen sodium F,V,OH,H DCEP
E11016-Gd,e Low-hydrogen potassium F,V,OH,H ac or DCEP
E11018-Gd,e Low-hydrogen potassium, iron powder F,V,OH,H ac or DCEP
E12015-Gd,e Low-hydrogen sodium F,V,OH,H DCEP
E12016-Gd,e Low-hydrogen potassium F,V,OH,H ac or DCEP
E12018-Gd,e Low-hydrogen potassium, iron powder F,V,OH,H ac or DCEP
E12018M1d,e Iron-powder, low hydrogen F,V,OH,H DCEP
100
PART C SPECIFICATIONS FOR WELDING RODS,
ELECTRODES, AND FILLER METALS SFA-5.5
TABLE 1 (CONTD)
ELECTRODE CLASSIFICATION
NOTES:
a. The letter suffix X as used in this table stands for the suffixes A1, B1, B3, etc. (see Table 2) and designates the chemical
composition of the weld metal. See A2.2.3 for more information on G classification.
b. The abbreviations, F,V,OH,H, and H-fillets indicate the welding position as follows:
F p Flat
H p Horizontal
H-fillets p Horizontal fillets
V p Vertical (For electrodes 316 in. (4.8 mm) and under, except 532 in. (4.0 mm) and under for classifications EXX15-X,
EXX16-X, EXX18-X)
OH p Overhead (For electrodes 316 in. (4.8 mm) and under, except 532 in. (4.0 mm) and under for classifications EXX15-
X, EXX16-X, EXX18-X).
c. The term DCEP refers to direct current, electrode positive (dc, reverse polarity). The term DCEN refers to direct current,
electrode negative (dc, straight polarity).
d. Electrodes classified as EXX15-X, EXX16-X, EXX18-X, or EXX18M(1) which meet supplemental absorbed moisture require-
ments in Table 11 may be further identified as shown in Table 11 and Figure 12.
e. Electrodes classified as EXX15-X, EXX16-X, EXX18-X, or EXX18M(1) which produce weld metal that meets the maximum
average level of diffusible hydrogen in Table 12 may be further identified as specified in Table 12 and Figure 12.
PART B TESTS, PROCEDURES, AND 8. Weld Test Assemblies

REQUIREMENTS
8.1 One or more of the following weld test assemblies
6. Summary of Tests are required for classification testing.
(1) The weld pad in Fig. 1 for chemical analysis of
The tests required for each classification are specified
the undiluted weld metal.
in Table 5. The purpose of these tests is to determine
the chemical composition, mechanical properties and (2) The groove weld in Fig. 2 for mechanical proper-
soundness of the weld metal, the usability of the ties and soundness of the weld metal for all classifica-
tions except EXX18M(1).
electrode, and the moisture content of the low-hydrogen
electrode covering. The base metal for the weld test (3) The fillet weld in Fig. 3 for the usability of the
assemblies, the welding and testing procedures to be electrode.
employed, and the results required are given in Sections (4) The groove weld in Fig. 4, an alternate to (2)
8 through 14. above, for mechanical properties and soundness of
The supplemental tests for absorbed moisture (see the weld metal made with the E9018M, E10018M,
Section 15, Absorbed Moisture Test), and for diffusible E11018M, E12018M, or E12018M1 electrode.
hydrogen (see Section 16, Diffusible Hydrogen Test), The sample for chemical analysis may be taken from
are not required for classification of the low-hydrogen the reduced section of the fractured tension test specimen
or from a corresponding location (or any location above
electrodes (see Note i of Table 5).
it) in the weld metal in the groove weld in Figs. 2
or 4. In case of dispute, the weld pad in Fig. 1 shall
be the referee method.
7. Retest 8.2 The preparation of each weld test assembly shall

be as prescribed in 8.3 through 8.5. The base metal
If the results of any test fail to meet the requirement, for each assembly shall be as required in Table 6 and
that test shall be repeated twice. The results of both shall meet the requirements of the ASTM specification
retests shall meet the requirement. Specimens for the shown there or an equivalent specification. Testing of
retest may be taken from the original test assembly or the assemblies shall be as prescribed in Sections 9
from a new test assembly. For chemical analysis, retest through 13.
need be only for those specific elements that failed to Electrodes other than low hydrogen, as defined in
meet the test requirement. Table 1, shall be tested without conditioning. Low-
101
SFA-5.5
TABLE 2
CHEMICAL COMPOSITION REQUIREMENTS FOR UNDILUTED WELD METAL
Wt. Percenta,b
Additional Elements
AWS UNS
Classificationc Numberd C Mn Si P S Ni Cr Mo Type Amt.
Carbon-Molybdenum Steel Electrodes
E7010-A1 W17010 0.12 0.60 0.40 0.03 0.03 0.400.65

E7011-A1 W17011 0.12 0.60 0.40 0.03 0.03 0.400.65
E7015-A1 W17015 0.12 0.90 0.60 0.03 0.03 0.400.65
E7016-A1 W17016 0.12 0.90 0.60 0.03 0.03 0.400.65
E7018-A1 W17018 0.12 0.90 0.80 0.03 0.03 0.400.65
E7020-A1 W17020 0.12 0.60 0.40 0.03 0.03 0.400.65
E7027-A1 W17027 0.12 1.00 0.40 0.03 0.03 0.400.65
Chromium-Molybdenum Steel Electrodes
2001 SECTION II
E8016-B1 W51016 0.050.12 0.90 0.60 0.03 0.03 0.400.65 0.400.65
E8018-B1 W51018 0.050.12 0.90 0.80 0.03 0.03 0.400.65 0.400.65
102
E8016-B2 W52016 0.050.12 0.90 0.60 0.03 0.03 1.001.50 0.400.65

E8018-B2 W52018 0.050.12 0.90 0.80 0.03 0.03 1.001.50 0.400.65
E7015-B2L W52115 0.05 0.90 1.00 0.03 0.03 1.001.50 0.400.65

E7016-B2L W52116 0.05 0.90 0.60 0.03 0.03 1.001.50 0.400.65
E7018-B2L W52118 0.05 0.90 0.80 0.03 0.03 1.001.50 0.400.65
E9015-B3 W53015 0.050.12 0.90 1.00 0.03 0.03 2.002.50 0.901.20

E9016-B3 W53016 0.050.12 0.90 0.60 0.03 0.03 2.002.50 0.901.20
E9018-B3 W53018 0.050.12 0.90 0.80 0.03 0.03 2.002.50 0.901.20
E8015-B3L W53115 0.05 0.90 1.00 0.03 0.03 2.002.50 0.901.20

E8018-B3L W53118 0.05 0.90 0.80 0.03 0.03 2.002.50 0.901.20
E8015-B4L W53415 0.05 0.90 1.00 0.03 0.03 1.752.25 0.400.65
E8016-B5 W51316 0.070.15 0.400.70 0.300.60 0.03 0.03 0.400.60 1.001.25 V 0.05
E8015-B6e W50215 0.050.10 1.0 0.90 0.03 0.03 0.40 4.06.0 0.450.65
E8016-B6e W50216 0.050.10 1.0 0.90 0.03 0.03 0.40 4.06.0 0.450.65
E8018-B6e W50218 0.050.10 1.0 0.90 0.03 0.03 0.40 4.06.0 0.450.65
E8015-B6Le W50205 0.05 1.0 0.90 0.03 0.03 0.40 4.06.0 0.450.65
(continued)
TABLE 2 (CONTD)
Wt. Percenta,b
Additional Elements
AWS UNS
Chromium-Molybdenum Steel Electrodes (continued)
E8016-B6Le W50206 0.05 1.0 0.90 0.03 0.03 0.40 4.06.0 0.450.65
E8018-B6Le W50208 0.05 1.0 0.90 0.03 0.03 0.40 4.06.0 0.450.65

E8015-B7e W50315 0.050.10 1.0 0.90 0.03 0.03 0.40 6.08.0 0.450.65
E8016-B7e W50316 0.050.10 1.0 0.90 0.03 0.03 0.40 6.08.0 0.450.65
ELECTRODES, AND FILLER METALS

E8018-B7e W50318 0.050.10 1.0 0.90 0.03 0.03 0.40 6.08.0 0.450.65
E8015-B7Le W50305 0.05 1.0 0.90 0.03 0.03 0.40 6.08.0 0.450.65
E8016-B7Le W50306 0.05 1.0 0.90 0.03 0.03 0.40 6.08.0 0.450.65
E8018-B7Le W50308 0.05 1.0 0.90 0.03 0.03 0.40 6.08.0 0.450.65
E8015-B8e W50415 0.050.10 1.0 0.90 0.03 0.03 0.40 8.010.5 0.851.20
E8016-B8e W50416 0.050.10 1.0 0.90 0.03 0.03 0.40 8.010.5 0.851.20
103
E8018-B8e W50418 0.050.10 1.0 0.90 0.03 0.03 0.40 8.010.5 0.851.20
E8015-B8Le W50405 0.05 1.0 0.90 0.03 0.03 0.40 8.010.5 0.851.20
E8016-B8Le W50406 0.05 1.0 0.90 0.03 0.03 0.40 8.010.5 0.851.20
E8018-B8Le W50408 0.05 1.0 0.90 0.03 0.03 0.40 8.010.5 0.851.20
E9015-B9 W50425 0.080.13 1.25 0.30 0.01 0.01 1.0 8.010.5 0.851.20 V 0.150.30
Cu 0.25
Al 0.04
Nb(Cb) 0.020.10
N 0.020.07
E9016-B9 W50426 0.080.13 1.25 0.30 0.01 0.01 1.0 8.010.5 0.851.20 V 0.150.30
Cu 0.25
Al 0.04
Nb(Cb) 0.020.10
N 0.020.07
E9018-B9 W50428 0.080.13 1.25 0.30 0.01 0.01 1.0 8.010.5 0.851.20 V 0.150.30
Cu 0.25
Al 0.04
Nb(Cb) 0.020.10
N 0.020.07
SFA-5.5
(continued)
SFA-5.5
TABLE 2 (CONTD)
Wt. Percenta,b
Additional Elements
AWS UNS
Nickel Steel Electrodes
E8016-C1 W22016 0.12 1.25 0.60 0.03 0.03 2.002.75

E8018-C1 W22018 0.12 1.25 0.80 0.03 0.03 2.002.75
E7015-C1L W22115 0.05 1.25 0.50 0.03 0.03 2.002.75

E7016-C1L W22116 0.05 1.25 0.50 0.03 0.03 2.002.75
E7018-C1L W22118 0.05 1.25 0.50 0.03 0.03 2.002.75
E8016-C2 W23016 0.12 1.25 0.60 0.03 0.03 3.003.75

E8018-C2 W23018 0.12 1.25 0.80 0.03 0.03 3.003.75
2001 SECTION II
E7015-C2L W23115 0.05 1.25 0.50 0.03 0.03 3.003.75
E7016-C2L W23116 0.05 1.25 0.50 0.03 0.03 3.003.75
E7018-C2L W23118 0.05 1.25 0.50 0.03 0.03 3.003.75
104
E8016-C3 W21016 0.12 0.401.25 0.80 0.03 0.03 0.801.10 0.15 0.35 V 0.05
E8018-C3i W21018 0.12 0.401.25 0.80 0.03 0.03 0.801.10 0.15 0.35 V 0.05
E7018-C3L W20918 0.08 0.401.40 0.50 0.03 0.03 0.801.10 0.15 0.35 V 0.05
E8016-C4 W21916 0.10 1.25 0.60 0.03 0.03 1.102.00

E8018-C4 W21918 0.10 1.25 0.80 0.03 0.03 1.102.00
E9015-C5L W25018 0.05 0.401.00 0.50 0.03 0.03 6.007.25
Nickel-Molybdenum Steel Electrodes
E8018-NM1 W21118 0.10 0.801.25 0.60 0.02 0.02 0.801.10 0.10 0.400.65 V 0.02
Cu 0.10
Al 0.05
Manganese-Molybdenum Steel Electrodes
E8018-D1 W18118 0.12 1.001.75 0.80 0.03 0.03 0.90 0.250.45

E9015-D1 W19015 0.12 1.001.75 0.60 0.03 0.03 0.90 0.250.45
E9018-D1 W19018 0.12 1.001.75 0.80 0.03 0.03 0.90 0.250.45
(continued)
TABLE 2 (CONTD)
Wt. Percenta,b
Additional Elements
AWS UNS
E10015-D2 W10015 0.15 1.652.00 0.60 0.03 0.03 0.90 0.250.45
E10016-D2 W10016 0.15 1.652.00 0.60 0.03 0.03 0.90 0.250.45
E10018-D2 W10018 0.15 1.652.00 0.80 0.03 0.03 0.90 0.250.45

E8016-D3 W18016 0.12 1.001.80 0.60 0.03 0.03 0.90 0.400.65
E8018-D3 W18018 0.12 1.001.80 0.80 0.03 0.03 0.90 0.400.65
E9018-D3 W19118 0.12 1.001.80 0.80 0.03 0.03 0.90 0.400.65
ELECTRODES, AND FILLER METALS

General Low-Alloy Steel Electrodes
EXX10-Gg 1.00h min 0.80h min 0.50h min 0.30h min 0.20h min V 0.10h min
Cu 0.20h min
Cu 0.20h min
EXX13-Gf 1.00h min 0.80h min 0.50h min 0.30h min 0.20h min V 0.10h min
105
Cu 0.20h min
Cu 0.20h min
Cu 0.20h min
Cu 0.20h min
E7020-G 1.00h min 0.80h min 0.50h min 0.30h min 0.20h min V 0.10h min
Cu 0.20h min
E7027-G 1.00h min 0.80h min 0.50h min 0.30h min 0.20h min V 0.10h min
Cu 0.20h min
Military-Similar Electrodes
E9018Mi W21218 0.10 0.601.25 0.80 0.030 0.030 1.401.80 0.15 0.35 V 0.05
E10018Mi W21318 0.10 0.751.70 0.60 0.030 0.030 1.402.10 0.35 0.250.50 V 0.05
E11018Mi W21418 0.10 1.301.80 0.60 0.030 0.030 1.252.50 0.40 0.250.50 V 0.05
E12018Mi W22218 0.10 1.302.25 0.60 0.030 0.030 1.752.50 0.301.50 0.300.55 V 0.05
E12018M1i W23218 0.10 0.801.60 0.65 0.015 0.012 3.003.80 0.65 0.200.30 V 0.05
(continued)
SFA-5.5
SFA-5.5
TABLE 2 (CONTD)
Wt. Percenta,b
Additional Elements
AWS UNS
Pipeline Electrodes
E7010-P1 W17110 0.20 1.20 0.60 0.03 0.03 1.00 0.30 0.50 V 0.10
E8010-P1 W18110 0.20 1.20 0.60 0.03 0.03 1.00 0.30 0.50 V 0.10
2001 SECTION II
Weathering Steel Electrodes
E7018-W1j W20018 0.12 0.400.70 0.400.70 0.025 0.025 0.200.40 0.150.30 V 0.08
106
Cu 0.300.60
E8018-W2j W20118 0.12 0.501.30 0.350.80 0.03 0.03 0.400.80 0.450.70 Cu 0.300.75
NOTES:
a. Single values are maximum, except where specified otherwise.
b. Weld metal shall be analyzed for those elements for which specific values are shown. Other elements listed without specified values shall be reported, if intentionally added. The total of
these latter unspecified elements and all other elements not intentionally added shall not exceed 0.50%.
c. The suffixes A1, B3, C3, etc. designate the chemical composition of the electrode classification.
d. SAE/ASTM Unified Numbering System for Metals and Alloys.
e. The E8015-B6 and E8015-B6L electrodes were formerly classified as E502-15 in AWS A5.4-81, Specification for Covered Corrosion-Resisting Chromium and Chromium Nickel Steel
Welding Electrodes. The E8016-B6 and E8016-B6L were formerly classified as E502-16 in A5.4-81. The E8018-B6 and E8018-B6L were not formerly classified but were produced to
the E502 composition ranges in A5.4-81 but with the EXX18 covering of this specification. Similarly, the E80XX-B7(L) classifications were formerly classified as E7Cr-XX in A5.4-81;
and the E80XX-B8(L) classifications were formerly classified as E505-XX in A5.4-81.
f. The letters XX used in the classification designation for EXX13-G in this table stand for various tensile-strength levels (80, 90, 100, 110, and 120 ksi) of weld metal.
g. The letters XX used in the classification designations for all electrodes except EXX13-G in this table stand for the various tensile-strength levels (70, 80, 90, 100, 110, and 120 ksi)
of electrodes.
h. In order to meet the alloy requirements of the G group, the undiluted weld metal shall have the minimum of at least one of the elements listed in this table. Additional chemical
requirements may be agreed to between supplier and purchaser.
i. These classifications are intended to be similar to types of electrodes covered by MIL-E-22200/1 and MIL-E-22200/10.
j. In AWS A5.5-81, E7018-W1 was designated E7018-W, and E8018-W2 was designated E8018-W.
TABLE 3
TENSION TEST REQUIREMENTSa,b
Tensile Strength Yield Strength, at 0.2% Offset
AWS Elongation Postweld
Classificationc ksi MPa ksi MPa Percent Conditiond
E7010-P1 70 480 60 415 22 AW
E7010-A1 70 480 57 390 22 PWHT
E7010-G 70 480 57 390 22 AW or PWHT
E7011-A1 70 480 57 390 22 PWHT
E7011-G 70 480 57 390 22 AW or PWHT
E7015-X 70 480 57 390 25 PWHT
E7015-B2L 75 520 57 390 19 PWHT
E7015-G 70 480 57 390 25 AW or PWHT
E7016-X 70 480 57 390 25 PWHT
E7016-B2L 75 520 57 390 19 PWHT
E7016-G 70 480 57 390 25 AW or PWHT
E7018-X 70 480 57 390 25 PWHT
E7018-B2L 75 520 57 390 19 PWHT
E7018-C3L 70 480 57 390 25 AW
E7018-W1 70 480 60 415 25 AW
E7018-G 70 480 57 390 25 AW or PWHT
E7020-A1 70 480 57 390 25 PWHT
E7020-G 70 480 57 390 25 AW or PWHT
E7027-A1 70 480 57 390 25 PWHT
E7027-G 70 480 57 390 25 AW or PWHT
E8010-P1 80 550 67 460 19 AW

E8010-G 80 550 67 460 19 AW or PWHT
E8011-G 80 550 67 460 19 AW or PWHT
E8013-G 80 550 67 460 16 AW or PWHT
E8015-X 80 550 67 460 19 PWHT
E8015-B3L 80 550 67 460 17 PWHT
E8015-G 80 550 67 460 19 AW or PWHT
E8016-X 80 550 67 460 19 PWHT
E8016-C3 80 550 68 to 80e 470 to 550e 24 AW
E8016-C4 80 550 67 460 19 AW
E8016-G 80 550 67 460 19 AW or PWHT
E8018-X 80 550 67 460 19 PWHT
E8018-B3L 80 550 67 460 17 PWHT
E8018-C3 80 550 68 to 80e 470 to 550e 24 AW
E8018-C4 80 550 67 460 19 AW
E8018-NM1 80 550 67 460 19 AW
E8018-W2 80 550 67 460 19 AW
E8018-G 80 550 67 460 19 AW or PWHT
E9010-G 90 620 77 530 17 AW or PWHT

E9011-G 90 620 77 530 17 AW or PWHT
E9013-G 90 620 77 530 14 AW or PWHT
E9015-X 90 620 77 530 17 PWHT
E9015-G 90 620 77 530 17 AW or PWHT
E9016-X 90 620 77 530 17 PWHT
E9016-G 90 620 77 530 17 AW or PWHT
E9018M 90 620 78 to 90e 540 to 620e 24 AW
E9018-X 90 620 77 530 17 PWHT
E9018-G 90 620 77 530 17 AW or PWHT
107
TABLE 3 (CONTD)
TENSION TEST REQUIREMENTSa,b
Tensile Strength Yield Strength, at 0.2% Offset
AWS Elongation Postweld
Classificationc ksi MPa ksi MPa Percent Conditiond
E10010-G 100 690 87 600 16 AW or PWHT
E10011-G 100 690 87 600 16 AW or PWHT
E10013-G 100 690 87 600 13 AW or PWHT
E10015-X 100 690 87 600 16 PWHT
E10015-G 100 690 87 600 16 AW or PWHT
E10016-X 100 690 87 600 16 PWHT
E10016-G 100 690 87 600 16 AW or PWHT
E10018M 100 690 88 to 100 610 to 690e 20 AW
E10018-X 100 690 87 600 16 PWHT
E10018-G 100 690 87 600 16 AW or PWHT
E11010-G 110 760 97 670 15 AW or PWHT

E11011-G 110 760 97 670 15 AW or PWHT
E11013-G 110 760 97 670 13 AW or PWHT
E11015-G 110 760 97 670 15 AW or PWHT
E11016-G 110 760 97 670 15 AW or PWHT
E11018-G 110 760 97 670 15 AW or PWHT
E11018M 110 760 98 to 110 680 to 760e 20 AW
E12010-G 120 830 107 740 14 AW or PWHT

E12011-G 120 830 107 740 14 AW or PWHT
E12013-G 120 830 107 740 11 AW or PWHT
E12015-G 120 830 107 740 14 AW or PWHT
E12016-G 120 830 107 740 14 AW or PWHT
E12018-G 120 830 107 740 14 AW or PWHT
E12018M 120 830 108 to 120 745 to 830e 18 AW
E12018M1 120 830 108 to 120 745 to 830e 18 AW
NOTES:
a. See Table 5 for sizes to be tested.
b. Single values are minimum, except as otherwise specified.
c. The letter suffix X as used in this table represents the suffixes (A1, B1, B2, etc.) except for those classifications which are tested in the
as-welded condition.
d. AW signifies as-welded with aging when it is specified in 11.2, PWHT signifies postweld heat treated as specified in 8.4.2 and in Table
7, except that the G designated classifications, marked as AW or PWHT in this table, may have weld metal tested with or without
PWHT as agreed between the supplier and purchaser.
e. For 332 in. (2.4 mm) electrodes, the upper value for the yield strength may be 5 ksi (35 MPa) higher than the indicated value.
hydrogen electrodes, that have not been adequately straight pass with the pass width not exceeding 212
protected against moisture absorption in storage, shall times the diameter of the core wire. The slag shall be
be held at a temperature of 500 to 800F (260 to removed after each pass. The pad may be quenched
427C) for a minimum of one hour prior to testing. in water between passes. The dimensions of the com-
pleted pad shall be as shown in Fig. 1. Testing of this
8.3 Weld Pad. A weld pad, when required, shall
assembly shall be as specified in Section 9, Chemical
be prepared as specified in Fig. 1. Base metal of any
Analysis.
convenient size of the type specified in Table 6 shall
be used as the base for the weld pad. The surface of 8.4 Groove Weld
the base metal on which the filler metal is deposited
shall be clean. The pad shall be welded in the flat 8.4.1 Mechanical Properties and Soundness. A
position with multiple layers to obtain undiluted weld test assembly shall be prepared and welded as specified
metal. The preheat temperature shall not be less than in Fig. 2 or 4 using base metal of the appropriate type
60F (16C) and the interpass temperature shall not specified in Table 6, of thickness specified in Fig. 2
exceed 300F (150C). Each weld pass shall be a single or 4. Testing of this assembly shall be as specified in
108
TABLE 4
CHARPY V-NOTCH IMPACT REQUIREMENTS
Limits for 3 out of 5 Specimensc
AWS Classification Average, min.b Single Value, min.b

E7018-W1 20 ftlbf at 0F 15 ftlbf at 0F
E8018-W2 (27J at 18C) (20J at 18C)
50 ftlbf at 0F 40 ftlbf at 0F
E12018M1
(67J at 18C) (54J at 18C)
E7010-P1 20 ftlbf at 20F 15 ftlbf at 20F

E8010-P1 (27J at 29C) (20J at 29C)
E8018-NM1
20 ftlbf at 40F 15 ftlbf at 40F
E8016-C3
(27J at 40C) (20J at 40C)
E8018-C3
E8016-D3, E8018-D1
E8018-D3, E9015-D1
20 ftlbf at 60Fa 15 ftlbf at 60Fa
E9018-D1, E9018-D3
(27J at 51C) (20J at 51C)
E10015-D2, E10016-D2
E10018-D2
E7018-C3L
E8016-C4, E8018-Cr 20 ftlbf at 60F 15 ftlbf at 60F)
E9018M, E10018M (27J at 51C) (20J at 51C)
E11018M, E12018M
E8016-C1 20 ftlbf at 75Fa 15 ftlbf at 75Fa

E8018-C1 (27J at 59C) (20J at 59C)
E7015-C1L
E7016-C1L
E7018-C1L
(27J at 73C) (20J at 73C)
E8016-C2
E8018-C2
E7015-C2L 20 ftlbf at 150Fa 15 ftlbf at 150Fa

E7016-C2L (27J at 101C) (20J at 101C)
E7018-C2L

E9015-C5L
(27J at 115C) (20J at 115C)
EXXXX-A1
EXXXX-BX
Not specified
EXXXX-BXL
EXXXX-G
NOTES:
a. These classifications are tested in the postweld heat treated condition. No thermal treatment shall be performed on the test specimens of all
other classifications.
b. Impact test values shall be recorded to nearest whole unit of energy absorbed in foot-pounds in accordance with the rounding-off method
specified in 5.2.
c. Both the highest and the lowest test values obtained shall be disregarded in computing the average value. Two of these three remaining values
shall equal or exceed the minimum average value listed; one of these three remaining values may be lower than minimum average value, but
shall not be less than the minimum single value listed. The average of the three remaining values shall not be less than the minimum average
value listed.
109
TABLE 5
REQUIRED TESTSa,b
Electrode Sizec Welding Position for Test Assembly
Soundness Test
Type of Chemical All Weld Metal Impact Fillet Moisture
AWS Classificationa Currenta in. mm Analysisd Tension Teste,f Testg Weld Testh Testj
3
E7010-X 32, 18 2.4, 3.2 NRb NRb NR NRb NR
5
E8010-X 32 4.0 F F NR V,OH NR
3
E9010-G 16 4.8 NRb F NR V,OH NR
DCEP 7
E10010-G 32 5.6 NRb NRb NR NRb NR
1
E11010-G 4 6.4 F F NR H NR
E12010-G
3
E7011-X 32, 18 2.4, 3.2 NRb NRb NR NRb NR
5
E8011-X 32 4.0 F F NR V,OH NR
3
E9011-G 16 4.8 NRb F NR V,OH NR
ac and DCEP 7
E10011-G 32 5.6 NRb NRb NR NRb NR
1
E11011-G 4 6.4 F F NR H NR
E12011-G
3
E8013-G 32, 18 2.4, 3.2 NRb NRb NR NRb NR
5
E9013-G 32 4.0 Fj Fj NR V,OH NR
ac, DCEN, 3
E10013-G 16 4.8 NRb Fj NR V,OH NR
and DCEP
E11013-G
E12013-G
3
E7015-X 32, 18 2.4, 3.2 NRb NRb NRb NRb NRb
5
E8015-X 32 4.0 F F F V,OH Reqd.
3
E9015-X 16 4.8 NRb F F H NRb
DCEP 7
E11015-X 32 5.6 NRb NRb NRb NRb NRb
1
E11015-G 4 6.4 F F F H Reqd.
E12015-G
3
E7016-X 32, 18 2.4, 3.2 NRb NRb NRb NRb NRb
5
E8016-X 32 4.0 F F F V,OH Reqd.
3
E9016-X 16 4.8 NRb F F H NRb
ac and DCEP 7
1
E11016-G 4 6.4 F F F H Reqd.
E12016-G
3
E7018-X 32, 18 2.4,3.2 NRb NRb NRb NRb NRb
5
E8018-X 32 4.0 F F F V,OH Reqd.
3
E9018-X 16 4.8 NRb F F H NRb
ac and DCEP 7
1
E11015-G 4 6.4 F F F H Reqd.
E12018-G
1
8 3.2 NRb NRb NR NRb NR
5
For H-fillets, 32 4.0 Fj Fj NR H NR
3
E7020-X ac and DCEN 16 4.8 NRb Fj NR H NR
7
E7027-X For flat position, 32 5.6 NRb NRb,k NR NRb NR
1
ac, DCEN and 4 6.4 Fj Fj,k NR H NR
5
DCEP 16 8.0 NRb Fj,k NR NRb NR
110
TABLE 5 (CONTD)
REQUIRED TESTSa,b
Electrode Sizec Welding Position for Test Assembly
Soundness Test
Type of Chemical All Weld Metal Impact Fillet Moisture
AWS Classificationa Currenta in. mm Analysisd Tension Teste,f Testg Weld Testh Testj
3
E9018M 32, 18 2.4, 3.2 NRb NRb NRb NRb NRb
5
E10018M 32 4.0 F F F V,OH Reqd.
3
E11018M DCEP 16 4.8 NRb F F H NRb
7
E12018M 32 5.6 NRb NRb NRb NRb NRb
1
E12018M1 4 6.4 F F F H Reqd.
NOTES:
a. NR means not required. The abbreviations, F, H, H-fillet, V, and OH, are defined in Note b of Table 1. The terms DCEP and DCEN
are defined in Note c of Table 1. The letter suffix X as used in this table is defined in Note a of Table 1.
b. Standard electrode sizes not requiring this specific test can be classified, provided at least two other sizes of that classification have passed
the tests required for them, or the size to be classified meets specification requirements by having been tested in accordance with Sections
8 through either 13, 14, 15, or 16, depending on the electrode being classified.
c. Electrodes manufactured in sizes not shown shall be tested to the requirement of the nearest standard size. 6.0 mm electrode shall be tested
to the requirements of 14 in. (6.4 mm) electrode.
d. See Section 9.
e. See Section 10.
f. See Section 11.
g. See Section 12. Impact tests are required for classifications listed in Table 4.
h. See Section 13.
i. The moisture test given in Section 14 is the required test for measurement of moisture content of the covering. The absorbed moisture test,
in Section 15, and the diffusible hydrogen test, in Section 16, are supplemental tests required only when their corresponding optional
supplemental designators are to be used with the classification designators.
j. When DCEP and DCEN are specified, only DCEN need be tested.
k. Electrodes longer than 18 in. (450 mm) will require a double length test assembly in accordance with Note 2 of Figure 2, to ensure uniformity
of the entire electrode.
Sections 10, Radiographic Test; 11, Tension Test; and 8.5 Fillet Weld. A weld test assembly shall be
12, Impact Test. The assembly shall be tested in prepared for particular sizes of electrodes of all classifi-
the as-welded condition or the postweld heat treated cations and welded as specified in Table 5 and Fig.
condition as specified in Table 3, except for the 3 using base metal of the appropriate type specified
E(X)XXYY-G classifications, which shall be tested in in Table 6. The welding positions and conditions shall
the postweld condition agreed to by the purchaser and be as specified in Table 8 and Fig. 5 according to the
supplier (see Note a of Table 7). size and classification of electrode. Testing of the
assembly shall be as specified in Section 13, Fillet
8.4.2 When required, the weld test assembly shall
Weld Test.
be postweld heat treated before removal of mechanical
test specimens. This postweld heat treatment may be
done either before or after the radiographic examination.
9. Chemical Analysis
8.4.2.1 Temperature of the weld test assembly
shall be raised, in a suitable furnace, at the rate of 9.1 The sample for chemical analysis shall be taken
150 to 500F (65 to 260C) per hour until the from weld metal obtained with the electrode. The
postweld heat treatment temperature, specified in Table sample shall be taken from a weld pad, or the reduced
7 for the electrode classification, is attained. Tempera- section of the fractured tension test specimen or from
ture shall be maintained for one hour. a corresponding location (or any location above it) in
the weld metal in the groove weld in Figs. 2 or 4.
8.4.2.2 The weld test assembly shall then be Areas where arc starts or craters exist shall be avoided.
cooled in the furnace at a maximum rate of 350F The top surface of the pad described in 8.3 and
(177C) per hour. The test assembly may be removed shown in Fig. 1 shall be removed and discarded and
from the furnace when the temperature has reached a sample for analysis shall be obtained from the underly-
600F (316C) and allowed to cool in still air. ing metal by any appropriate mechanical means. The
111
sample shall be free of slag and shall be taken from

metal that is at least the minimum distance from the
original base metal surface as specified in Fig. 1.
The sample from the reduced section of the fractured
tension test specimen or from a corresponding location
(or any location above it) in the groove weld in Figs.
2 or 4 shall be prepared for analysis by any suitable
mechanical means.
9.2 The sample described in 9.1 shall be analyzed

by accepted analytical methods. The referee method
shall be ASTM E350, Method for Chemical Analysis
of Carbon Steel, Low Alloy Steel, Silicon Electrical
Steel, Ingot Iron and Wrought Iron.
9.3 The results of the chemical analysis shall meet

the requirements of Table 2 for the classification of
the electrode under test.
10. Radiographic Test

10.1 The groove weld described in 8.4.1 and shown
in Fig. 2 or 4 shall be radiographed to evaluate the
soundness of the weld metal for all classifications as
specified in Table 5. In preparation for radiography,
the backing shall be removed and both surfaces of the
weld shall be machined or ground smooth. The finished
surface of the weld may be flush with the plate or
have a reasonably uniform reinforcement not exceeding
3
32 in. (2.4 mm). Both surfaces of the test assembly
shall be smooth enough to avoid difficulty in interpreting
the radiograph.
10.2 The weld shall be radiographed in accordance

with ASTM E142, Method for Controlling Quality of
Radiographic Testing. The quality level of inspection
shall be 2-2T.
10.3 The soundness of the weld metal meets the

requirements of this specification if the radiograph
shows:
(1) no cracks or incomplete fusion.
(2) no slag inclusions longer than 14 in. (6 mm) or
1
3 of the thickness of the weld, whichever is greater,
or no groups of slag inclusions in line that have an
aggregate length greater than the thickness of the weld
in a length 12 times the thickness of the weld except
when the distance between the successive inclusions
exceeds 6 times the length of the longest inclusion in
FIG. 1 PAD FOR CHEMICAL ANALYSIS OF
the group.
UNDILUTED WELD METAL
(3) no rounded indications in excess of those permit-
ted by the radiographic standards in Fig. 6 according
to the grade specified in Table 9.
112
FIG. 2 GROOVE WELD TEST ASSEMBLY FOR MECHANICAL PROPERTIES AND SOUNDNESS OF WELD
METAL PRODUCED BY USING ALL ELECTRODE CLASSIFICATIONS EXCEPT EXX18M(1)
113
METAL PRODUCED BY USING ALL ELECTRODE CLASSIFICATIONS EXCEPT EXX18M(1) (CONTD)
One inch (25 mm) of the weld measured from each fications shall be aged at 200 to 220F (95 to 105C)
end of the assembly shall be excluded from radiographic for 48 hours plus or minus 2 hours, and cooled in air
examination. to room temperature. Other tension test specimens to
be tested in the as-welded condition may be aged at
10.4 A rounded indication is an indication (on the
200 to 220F (95 to 105C) for up to 48 hours and
radiograph) whose length is no more than three times
cooled to room temperature. See A6.3 for a discussion
its width. Rounded indications may be circular, elliptical,
of the purpose of aging treatments. All specimens shall
conical, or irregular in shape, and they may have tails.
be tested in the manner described in the tension testing
The size of a rounded indication is the largest dimension
section of ANSI/AWS B4.0, Standard Methods for
of the indication, including any tail that may be present.
Mechanical Testing of Welds.
The indication may be porosity or slag. Indications
whose largest dimension does not exceed 164 in. (0.4 11.3 Results of the tension test shall meet the require-
mm) shall be disregarded. Test assemblies with indica- ments specified in Table 3.
tions larger than the large indications permitted in the
radiographic standards do not meet the requirements
12. Impact Test
of this specification.
12.1 Five Charpy V-notch impact specimens, as
specified in Fig. 8, shall be machined from the test
11. Tension Test
assembly shown in Fig. 2 or 4 for those classifications
11.1 One all-weld-metal tension test specimen shall for which impact testing is required in Table 5.
be machined from the groove weld described in 8.4.1
12.2 The five specimens shall be tested in accordance
and shown in Fig. 2 or 4. The dimensions of the
with the fracture toughness testing section of ANSI/
specimen shall be as shown in Fig. 7.
AWS B4.0, Standard Methods for Mechanical Testing
11.2 The tension specimens for electrodes E7010- of Welds. The test temperature shall be that specified
G, E7010-P1, E8010-G, E8010-P1, and E9010-G classi- in Table 4 for the classification under test.
114
FIG. 3 FILLET WELD TEST ASSEMBLY
115
METAL PRODUCED BY USING EXX18M(1)
116
TABLE 6
BASE METAL FOR WELD TEST ASSEMBLIES
AWS Classification Base Metals ASTM Specification UNS Number*
All except E(X)XXYYM(1) Carbon Steel A29 Grade 1015 or equiv. G10150
All except E(X)XXYYM(1) Carbon Steel A29 Grade 1020 or equiv. G10200
All except E(X)XXYYM(1) Carbon Steel A283 Grade D or equiv. K02702
All except E(X)XXYYM(1) Carbon Steel A285 Grade A or equiv. K01700
All except E(X)XXYYM(1) Carbon Steel A285 Grade B or equiv. K02200
All except E(X)XXYYM(1) Carbon Steel A285 Grade C or equiv. K02801
All Carbon Steel A36 or equivalent K02600
All Carbon Steel A131 Grade B or equiv. K02102
*SAE/ASTM Unified Numbering System for Metals and Alloys
TABLE 7
PREHEAT, INTERPASS, AND POSTWELD HEAT TREATMENT TEMPERATURES
Preheat and Interpass Postweld Heat Treatment
Temperature Temperature
AWS Classification F C F C
E7010-A1
E7011-A1
E7015-A1
E7016-A1
E7018-A1
E7020-A1
E7027-A1
E8018-D1 200 to 225 93 to 107 1150 25 620 14
E9015-D1
E9018-D1
E10015-D2
E10016-D2
E10018-D2
E8016-D3
E8018-D3
E9018-D3
E8016-B1
E8018-B1
E8015-B2
E8016-B2
E8018-B2
E7015-B2L
E7016-B2L
E7018-B2L 325 to 375 163 to 191 1275 25 690 14
E9015-B3
E9016-B3
E9018-B3
E8015-B3L
E8018-B3L
E8015-B4L
E8016-B5
(continued)
117
TABLE 7 (CONTD)
E8015-B6
E8016-B6
E8018-B6
E8015-B6L
E8016-B6L
E8018-B6L
E8015-B7 350 to 450 177 to 232 1375 25 740 14
E8016-B7
E8018-B7
E8015-B7L
E8016-B7L
E8018-B7L
E8015-B8
E8016-B8
E8018-B8
E8015-B8L 400 to 500 205 to 260 1375 25 740 14
E8016-B8L
E8018-B8L
E9015-B9
E9016-B9 450 to 550 232 to 288 1375 25 740 14
E9018-B9
E8016-C1
E8018-C1
E7015-C1L
E7016-C1L
E7018-C1L
E8016-C2 200 to 225 93 to 107 1125 25 605 + 14
E8018-C2
E7015-C2L
E7016-C2L
E7018-C2L
E9015-C5L 200 to 250 93 to 121 1075 25 579 14
E8018-G
E8011-G
E8013-G
E9010-G
E9011-G
E9013-G
E10010-G
E10011-G 325 to 375 163 to 191 See Note a
E10013-G
E11010-G
E11011-G
E11013-G
E12010-G
E12011-G
E12013-G
118
TABLE 7 (CONTD)
E7010-G
E7011-G
E7015-G
E7016-G
E7018-G
E7020-G
E7027-G
E8015-G
E8016-G
E8018-G
E9015-G 200 to 225 93 to 107 See Note a
E9016-G
E9018-G
E10015-G
E10016-G
E10018-G
E11015-G
E11016-G
E11018-G
E12015-G
E12016-G
E12018-G
E7010-P1
E7018-C3L
E7018-W1
E8016-C3
E8018-C3
E8016-C4
E8018-C4 200 to 250 93 to 121 Not specifiedb
E8018-NM1
E8018-W2
E9018M
E10018M
E11018M
E12018M
E12018M1
E8018-P1 325 to 375 163 to 191 Not specifiedb
NOTES:
a. The need and specific values for postweld heat treatment of weld test assemblies made with these G electrodes shall be as agreed between
supplier and purchaser.
b. Postweld heat treatment is not required for those classifications listed as as-welded in Table 3.
119
TABLE 8
REQUIREMENTS FOR PREPARATION OF FILLET WELD TEST ASSEMBLIES
Electrode Plate Sizeb
Thickness Length Size of

Size Length (T) min (L)c Fillet Weld
AWS Position of
Classificationa in. mm in. mm in. mm in. mm Welding in. mm
3
32 2.4 12 300 1
8 3.2 10 250 V,OH 5
32 max. 4.0

1 1 3
8 3.2 14 350 4 6.4 12 300 V,OH 16 max. 4.8
5 3 1

EXX10-X 32 4.0 14 350 8 9.5 12 300 V,OH 4 max. 6.4
3 3 5
EXX11-X 16 4.8 14 350 8 9.5 12 300 V,OH 16 max. 8.0
7
32 5.6 14 or 18 350 or 450 1
2 12.5 12 or 16 300 or 400 H 1
4 min. 6.4
1
4 6.4 18 450 1
2 12.5 16 400 H 1
4 min. 6.4
3
32 2.4 12 300 1
8 3.2 10 250 V,OH 5
32 max. 4.0
1
8 3.2 14 350 1
4 6.4 12 300 V,OH 3
16 max. 4.8
EXX13-X 5
32 4.0 14 350 3
8 9.5 12 300 V,OH 1
4 max. 6.4
3
16 4.8 14 350 3
8 9.5 12 300 V,OH 3
8 max. 9.5
7
32 5.6 14 or 18 350 or 450 1
2 12.5 12 or 16 300 or 400 H 1
4 min. 6.4
EXX15-X 3
32 2.4 12 or 14 300 or 350 1
8 3.2 10 or 12 250 or 300 V,OH 3
16 max. 4.8

1 1 1
EXX16-X 8 3.2 14 350 4 6.4 12 300 V,OH 4 max. 6.4
5 3 5
EXX18M
E12018M1 3
32
16
4.0
4.8
14
14
350
350 3
8
8
9.5
9.5
12
12
300
300
V,OH
H 3
16 max.
16 min.
8.0
4.8
EXX18-X 7
32 5.6 14 or 18 350 or 450 1
2 12.5 12 or 16 300 or 400 H 1
4 min. 6.4
1
4 6.4 18 450 1
2 12.5 16 400 H 5
16 min. 8.0
1
8 3.2 14 350 1
4 6.4 12 300 H 1
8 min. 3.2

5 3 3
32 4.0 14 350 8 9.5 12 300 H 16 min. 4.8
3 3 1
E7020-X
E7027-X 7
16
32
4.8
5.6
14 or 18
18 or 28
350 or 450
450 or 700 1
8
2
9.5
12.5
12 or 16
16 or 26
300 or 400
400 or 650
H
H 1
4 min.
4 min.
6.4
6.4
1
4 6.4 18 or 28 450 or 700 1
2 12.5 16 or 26 400 or 650 H 5
16 min. 8.0
5
16 8.0 18 or 28 450 or 700 1
2 12.5 16 or 26 400 or 650 H 3
8 min. 9.5
NOTES:
a. The letters XX used in the classification designations in this table represent the various strength levels (70, 80, 90, 100, 110, and 120
ksi) of the weld metal. The letter suffix X as used in this table is defined in Note a of Table 1.
b. See Figure 3.
c. A starting tab, or a longer test assembly shall be used to ensure that the end of the first bead is more than 4 in. (100 mm) from the end of
the test assembly.
12.3 In evaluating the results for all the classifications entire face of the completed fillet weld shall be examined
that require impact testing, the lowest and the highest visually. The test specimen shall be free of cracks,
values obtained shall be disregarded. Two of the three overlap, slag, and porosity, and shall be substantially
remaining values shall equal, or exceed, the minimum free of undercut. An infrequent short undercut up to
1
average energy level specified in Table 4. One of the 32 in (0.8 mm) in depth shall be allowed. After the
three may be lower, but not lower than the minimum visual examination, a specimen, approximately 1 in.
single value specified in Table 4. The average of the (25 mm) in length, shall be removed as shown in Fig.
three shall not be less than the minimum average energy 3. One cross-sectional surface of the specimen shall
level specified in Table 4. be polished, etched, and then examined as required
in 13.2.
13. Fillet Weld Test
13.2 Scribe lines shall be placed on the prepared
13.1 The fillet weld test, when required in Table 5, surface, as shown in Fig. 9, and the fillet weld size,
shall be made in accordance with 8.5 and Fig. 3. The fillet weld leg, and convexity shall be determined to
120
FIG. 5 WELDING POSITIONS FOR FILLET WELD TEST ASSEMBLIES
the nearest 164 in. (0.4 mm) by actual measurement except for electrodes of the E(X)XX13-G classifications.
(see Fig. 9). These measurements shall meet the require- Fillet welds made with electrodes of these classifications
ments of Table 8 with respect to minimum or maximum may exhibit incomplete joint penetration through the
fillet weld size and the requirements of Table 10 with entire weld length, provided that at no point this
respect to maximum convexity and maximum difference incomplete joint penetration exceeds 25 percent of the
between fillet weld legs according to fillet weld size smaller leg of the fillet weld.
measured.
13.3 The remaining two sections of the test assembly
shall be broken through the fillet weld by a force 14. Moisture Test
exerted as shown in Fig. 10. When necessary to facilitate
fracture through the fillet weld, one or more of the 14.1 The moisture content of the covering on the
following procedures may be used: low-hydrogen electrodes, when required in Table 5,
(1) A reinforcing bead, as shown in Fig. 10, may shall be determined by any suitable method. In case
be added to each leg of the weld. of dispute, the method described in 14.3 through 14.9
(2) The position of the web on the flange may be shall be the referee method.
changed, as shown in Fig. 10.
14.2 The electrode shall be tested without condition-
(3) The face of the fillet may be notched, as shown
ing unless the manufacturer recommends otherwise. If
in Fig. 10.
the electrodes are conditioned, that fact, along with
Tests in which the weld metal pulls out of the base
the method used for conditioning, and the time and
metal during bending are invalid tests. Specimens in
temperature involved in the conditioning shall be noted
which this occurs shall be replaced, specimen for
on the test record. The moisture content shall not
specimen, and the test completed. In this case, the
exceed the limit specified in Table 11.
doubling of specimens required for retest in Section
7, Retest, does not apply.
14.3 The referee method for moisture consists of
13.4 The fractured surfaces shall be visually examined heating a sample of the covering in a nickel or clay
without magnification. The fractured surface shall be boat placed inside a combustion tube in order to remove
free of cracks. Incomplete joint penetration or incom- the moisture from the covering. A stream of oxygen
plete fusion at the weld root, in cumulative length, is used to carry the moisture to an absorption tube,
shall not be greater than 20 percent of the total length where the moisture is collected. The moisture content
of the weld. There shall be no continuous length of of the covering is determined by the increase in weight
incomplete joint penetration or incomplete fusion greater of the absorption tube and is expressed as a percentage
than 1 in. (25 mm), as measured along the weld axis, of the original weight of the sample of covering.
121
FIG. 6 RADIOGRAPHIC ACCEPTANCE STANDARDS FOR ROUNDED INDICATIONS (GRADE 1)
122
FIG. 6 RADIOGRAPHIC ACCEPTANCE STANDARDS FOR ROUNDED INDICATIONS (GRADE 2) (CONTD)
123
TABLE 9 14.4 The apparatus used for moisture testing with

RADIOGRAPHIC SOUNDNESS REQUIREMENTS the referee method3 shall be as shown in Fig. 11 and
AWS Classificationa Radiographic Standardb,c shall consist of the following:
EXX15-X
(1) A tube furnace with a heating element long
EXX16-X enough to heat at least 6 in. (150 mm) of the middle
EXX18-X Grade 1 portion of the combustion tube to 2000F (1093C).
E7020-X (2) An oxygen purifying train consisting of a needle
EXX18M
valve, a flow meter, a 96 percent sulfuric acid wash
E12018M1
bottle, a spray trap, and an anhydrous magnesium
EXX10-X perchlorate drying tower.
EXX11-X (3) A fused silica combustion tube of at least 78
EXX13-G Grade 2 in. (22 mm) inside diameter with plain ends and a
E7027-X
devitrification point above 2000F (1093C). (A high-
NOTES: temperature ceramic tube can be used, but a higher
a. The letters XX used in the classification designations in this
table, stand for the various strength levels (70, 80, 90, 100, 110,
value will be obtained for the blanks.) A plug of glass
and 120) of electrodes. The letter suffix X as used in this table wool, fine enough to filter the gases, shall be inserted
stands for the suffixes A1, B1, B2, etc. (see Table 2). far enough into the exit end of the combustion tube
b. See Figure 6.
c. The radiographic soundness obtainable under actual industrial con-
to be heated to a temperature of 400 to 500F (204
ditions employed for the various electrode classifications is dis- to 260C).
cussed in A6.10.1 in the Annex.
3
Modifications of the type described in A8, Modification of Moisture
Test Apparatus, which give equivalent results, also meet the require-
ments of this specification.
FIG. 7 ALL-WELD-METAL TENSION TEST SPECIMEN DIMENSIONS
124
FIG. 8 CHARPY V-NOTCH IMPACT TEST SPECIMEN
(4) A water absorption train consisting of a U- period of 20 minutes, the absorption U-tube shall be
tube (Schwartz-type) filled with anhydrous magnesium weighed.
perchlorate and a concentrated sulfuric acid gas-sealing
bottle. 14.7 In the determination of the blank value, the
procedure for an actual moisture determination shall
14.5 In conducting the moisture test, a sample of be followed step-by-step with the single exception of
approximately 4 grams of covering shall be prepared omitting the sample. The boat shall be removed from
as a composite of the covering from the middle of the desiccator and exposed to the atmosphere for a
three electrodes taken from the same package. The period approximating the time required to transfer a
covering shall be removed by bending the electrode sample from the balance pan to the boat. The combustion
or by pinching the covering with clean, dry pliers or tube shall be opened, the weighed absorption U-tube
forceps. Immediately upon removal, the sample of attached, the empty boat placed in the hot zone of the
covering shall be transferred to a dried, stoppered vial combustion tube, and the tube closed. After a heating
or sample bottle. period of 30 minutes, the absorption U-tube shall be
removed and placed in the balance case. The boat shall
14.6 The furnace shall be operated at 1775 to be transferred to the desiccator. After the 20 minute
1825F (968 to 996C) with an oxygen flow of 200 cooling period, the absorption U-tube shall be weighed
to 250 mL per minute. The empty boat (see 14.3) shall and the gain in weight shall be taken as the blank
be placed in the hot zone of the combustion tube, for value.
drying, and the absorption U-tube assembly shall be
attached to the system for conditioning. After 30 14.8 Immediately after weighing the absorption U-
minutes, the absorption U-tube shall be removed and tube, the sample of the covering shall be weighed and
placed in the balance case. The boat shall be removed quickly transferred to the boat. The combustion tube
and placed in a desiccator in which anhydrous magne- shall be opened, the weighed absorption U-tube attached,
sium perchlorate is used as a desiccant. After a cooling the boat with sample transferred to the hot zone of
125
the combustion tube, and the tube closed. After heating

for 30 minutes, the absorption U-tube shall be removed
and placed in the balance case. If another sample is
to be run, the boat shall be taken from the combustion
tube, the sample removed, and the boat transferred to
the desiccator. The absorption U-tube shall be weighed
after the 20 minute cooling period. Another determina-
tion may be started immediately, since it is not necessary
to repeat the blank determination provided the same
combustion boat can be used.
14.9 The calculation shall be made according to the
following formula:
AB
Percent Moisturep 100
initial weight of sample
where:
Ap gain in weight of absorption tube in moisture
determination
Bp gain in weight of absorption tube in blank deter-
mination
15. Absorbed Moisture Test

15.1 In order for a low-hydrogen electrode to be
designated as low-moisture-absorbing with the R suf-
fix designator, sufficient electrodes shall be exposed to
an environment of 80F and 80% relative humidity for
a period of not less than 9 hours by any suitable method.
In case of dispute, the exposure method described in
15.2 through 15.6 shall be the referee method. The
moisture content of the electrode covering on the low-
moisture-absorbing, low-hydrogen electrodes (EXX15-
X-R, EXX16-X-R, EXX18-X-R) shall be determined
by any suitable method. In case of dispute, the method
described in 14.3 through 14.9 shall be the referee
method for determination of moisture content. The
moisture content of the exposed covering shall not
exceed the maximum specified moisture content for the
R designated electrode and classification in Table 11.
15.2 An electrode sample of the smallest and the
largest sizes of the R designated electrode shall
be used for controlled environmental exposure. If the
electrodes are conditioned prior to exposure, that fact,
along with the method used for conditioning, and the
time and temperature involved in conditioning, shall
be noted on the test record. Conditioning of electrodes
after exposure is not permitted.
FIG. 9 DIMENSIONS OF FILLET WELDS
15.3 The electrode samples described in 15.2 shall
be exposed in a suitably calibrated and controlled
environmental chamber for nine hours minimum at
126
TABLE 10
DIMENSIONAL REQUIREMENTS FOR FILLET WELD USABILITY TEST SPECIMENS
Maximum Difference Between Fil-
Measured Fillet Weld Size Maximum Convexity let Weld Legs
in. mm in. mm in. mm

1 3 1
8, or less 3.2 64 1.2 32 0.8
9 3 3
64 3.6 64 1.2 64 1.2
5 3 3
32 4.0 64 1.2 64 1.2
11 1 1
64 4.4 16 1.6 16 1.6
3 1 1
16 4.8 16 1.6 16 1.6
13 1 5
64 5.2 16 1.6 64 2.0
7 1 5
32 5.6 16 1.6 64 2.0
15 1 3
64 6.0 16 1.6 32 2.4
1 1 3
4 6.4 16 1.6 32 2.4
17 1 7
64 6.7 16 1.6 64 2.8
9 1 7
32 7.1 16 1.6 64 2.8
19 5 1
64 7.5 64 2.0 8 3.2
5 5 1
16 8.0 64 2.0 8 3.2
21 5 9
64 8.3 64 2.0 64 3.6
11 5 9
32 8.7 64 2.0 64 3.6
23 5 5
64 9.1 64 2.0 32 4.0
3 5 5
8, or more 9.5 64 2.0 32 4.0
FIG. 10 ALTERNATE METHODS FOR FACILITATING FRACTURE OF THE FILLET WELD
80F, minus 0, plus 5F (26.7C, minus 0, plus 2.8C) (3) The apparatus shall have a drip-free area where
and 80% relative humidity, minus 0, plus 5%. covered electrodes up to 18 in. (450 mm) in length
can be positioned with length as perpendicular as
15.4 The environmental chamber described in 15.3
shall meet the following design requirements: practical to the general air flow.
(1) The apparatus shall be an insulated humidifier (4) The apparatus shall have a calibrated means of
which produces the temperature of adiabatic saturation continuously measuring and recording the dry bulb
through regenerative evaporation or vaporization of temperature and either the wet bulb temperature or the
water. differential between the dry bulb and the wet bulb
(2) The apparatus shall have an average air speed temperature over the period of time required.
within the envelope of air surrounding the covered (5) The apparatus shall have an air speed of at least
electrodes of 100 to 325 fpm (0.5 to 1.7 m/sec). 900 fpm (4.5 m/sec) over the wet bulb sensor unless
127
TABLE 11
MOISTURE CONTENT LIMITS IN ELECTRODE COVERINGS
Limit of Moisture Content, % by wt., max.
AWS Classification Electrode Designationa As-Received or Reconditionedb As-Exposedc

E7015-X E7015-X, E7015-X-HZ
E7016-X E7016-X, E7016-X-HZ 0.4 Not specified
E7018-X E7018-X, E7018-X-HZ
E7015-X E7015-X-R, E7015-X-HZR
E7016-X E7016-X-R, E7016-X-HZR 0.3 0.4
E7018-X E7018-X-R, E7018-X-HZR
E8015-X E8015-X, E8015-X-HZ
E8018-X E8018-X, E8018-X-HZ
E8015-X E8015-X-R, E8015-X-HZR
E8016-X E8016-X-R, E8016-X-HZR 0.2 0.4
E8018-X E8018-X-R, E8018-X-HZR
E9015-X E9015-X, E9015-X-HZ
E9016-X E9016-X, E9016-X-HZ
0.15 Not specified
E9018-X E9018-X, E9018-X-HZ
E9018M E9018M, E9018M-HZ
E9015-X E9015-X-R, E9015-X-HZR
E9016-X E9016-X-R, E9016-X-HZR
0.15 0.4
E9018-X E9018-X-R, E9018-X-HZR
E9018M E9018M-R, E9018M-HZR
E10015-X E10015-X, E10015-X-HZ
E10018-X E10018-X, E10018-X-HZ
E10018M E10018M, E10018M-HZ
E10015-X E10015-X-R, E10015-X-HZR
E10016-X E10016-X-R, E10016-X-HZR
0.15 0.4
E10018-X E10018-X-R, E10018-X-HZR
E10018M E10018M-R, E10018M-HZR
E10015-G E11015-G, E11015-G-HZ
E11016-G E11016-G, E11016-G-HZ
0.15 Not specified
E11018-G E11018-G, E11018-G-HZ
E11018M E11018M, E11018M-HZ
E11015-G E11015-G-R, E11015-G-HZR
E11016-G E11016-G-R, E11016-G-HZR
0.15 0.4
E11018-G E11018-G-R, E11018-G-HZR
E11018M E11018M-R, E11018M-HZR
E12015-G E12015-G, E12015-G-HZ
E12016-G E12016-G, E12016-G-HZ
0.15 Not specified
E12018-G E12018-G, E12018-G-HZ
E12018M E12018M, E12018M-HZ
E12015-G E12015-G-R, E12015-G-HZR
E12016-G E12016-G-R, E12016-G-HZR
0.15 0.4
E12018-G E12018-G-R, E12018-G-HZR
E12018M E12018M-R, E12018M-HZR
E12018M1 E12018M1, E12018M1-HZ 0.10 Not specified
E12018M1 E12018M1-R, E12018M1-HZR 0.10 0.4
NOTES:
a. See Section 16 and Table 12.
b. As-received or reconditioned electrode coverings shall be tested as specified in Section 14.
c. As-exposed electrode coverings shall be treated with a moist environment as specified in 15.2 through 15.6 before being tesed as specified
in 15.1.
128
FIG. 11 SCHEMATIC OF TRAIN FOR MOISTURE DETERMINATION
the wet bulb sensor can be shown to be insensitive to (4) Time, temperature, and humidity shall be continu-
air speed or has a known correction factor that will ously recorded for the period that the electrodes are
provide for an adjusted wet bulb reading equal to the in the chamber.
temperature of adiabatic saturation. (5) Counting of the exposure time shall start when
(6) The apparatus shall have the wet bulb sensor the required temperature and humidity in the chamber
located on the suction side of the fan so that there is are established.
an absence of heat radiation on the sensor. (6) At the end of the exposure time, the electrode
shall be removed from the chamber and a sample of
15.5 The exposure procedure for electrode samples the electrode covering taken for moisture determination,
shall be as follows: as specified in Section 14, Moisture Test.
(1) The electrode sample in unopened packages, or
from reconditioned lots, shall be heated to a temperature, 15.6 The manufacturer shall control other test vari-
minus 0, plus 10F above the dew point of the chamber ables which are not defined, but which must be con-
at the time of loading. In this case, the dew point trolled to ensure a greater consistency of results.
temperature is 73F (22.8C).
(2) The electrode sample shall be loaded into the
chamber without delay after the packages are opened. 16. Diffusible Hydrogen Test
(3) The electrodes shall be placed in the chamber The smallest and the largest sizes of the electrode
in a vertical or horizontal position on one inch centers, of each classification to be designated by the optional
with the length of the electrode as perpendicular as supplemental diffusible hydrogen designator shall be
practical to the general air flow. tested according to one of the methods given in ANSI/
129
TABLE 12
DIFFUSIBLE HYDROGEN REQUIREMENTS FOR WELD METAL AND OPTIONAL SUPPLEMENTAL DESIGNATORS
Diffusible Hydrogen Content,
Diffusible Hydrogen Average, Maximumb
AWS Classification Designatora mL(H2)/100g Deposited Metal
H16 16.0
E(X)XX15-X, E(X)XX16-X,
E(X)XX18-X, or E(X)XX18M(1) H8
H4
8.0
4.0
NOTES:
a. Diffusible hydrogen testing of low hydrogen electrode classifications is only required when the diffusible hydrogen designator is added to the
classification as specified in Figure 12. See Section 16.
b. The lower average diffusible hydrogen levels (H8 and H4) may not be available in all low hydrogen classifications.
AWS A4.3, Standard Methods for Determination of produce electrodes that meet the requirements of this
the Diffusible Hydrogen Content of Martensitic, Bainitic, specification.
and Ferritic Weld Metal Produced by Arc Welding.
Testing shall be done without conditioning of the
electrode, unless the manufacturer recommends other- 18. Standard Sizes and Lengths
wise. If the electrodes are conditioned, that fact, along
18.1 Standard sizes (diameter of the core wire) and
with the method used for conditioning, and the time
lengths of electrodes are shown in Table 13.
and temperature involved in conditioning, shall be noted
on the test record. The diffusible hydrogen designator 18.2 The diameter of the core wire shall not vary
may be added to the classification according to the more than plus or minus 0.002 in. (0.05 mm) from
average test value as compared to the requirements of the diameter specified. The length shall not vary more
Table 12. than plus or minus 14 in. (6.4 mm) from that specified.
For purposes of certifying compliance with diffusible
hydrogen requirements, the reference atmospheric condi-
tion4 shall be an absolute humidity of 10 grains of 19. Core Wire and Covering
water vapor per pound (1.43 g/kg) of dry air at the
time of welding. The actual atmospheric conditions 19.1 The core wire and covering shall be free of
shall be reported along with the average value for the defects that would interfere with uniform deposition of
test according to ANSI/AWS A4.3. the electrode.
When the absolute humidity equals or exceeds the
19.2 The core wire and the covering shall be concen-
reference condition at the time of preparation of the test
tric to the extent that the maximum core-plus-one
assembly, the test shall be acceptable as demonstrating
covering dimension shall not exceed the minimum core-
compliance with the requirements of this specification,
provided the actual test results satisfy the diffusible plus-one covering dimension by more than:
hydrogen requirements for the applicable designator. (1) seven percent of the mean dimension in sizes
3
Likewise, if the actual test results for an electrode meet 32 in. (2.4 mm) and smaller;
the requirements for the lower, or lowest hydrogen (2) five percent of the mean dimension in sizes 18
designator, as specified in Table 12, the electrode in. (3.2 mm) and 532 in. (4.0 mm); and
also meets the requirements for all higher hydrogen (3) four percent of the mean dimension in sizes 316
designators in Table 12 without the need to retest. in. (4.8 mm) and larger.
Concentricity may be measured by any suitable
means.
PART C MANUFACTURE,
IDENTIFICATION, AND PACKAGING
20. Exposed Core
17. Method of Manufacture
20.1 The grip end of each electrode shall be bare
The electrodes classified according to this specifica-
tion may be manufactured by any method that will (free of covering) for a distance of not less than 12
in. (12.5 mm), nor more than 114 in. (30 mm) for
5
4
See A9.2 (in the Annex) for further explanation of reference 32 in. (4.0 mm) and smaller sizes, and not less than
3
atmospheric condition in psychometric terms. 4 in. (19 mm) nor more than 112 in. (40 mm) for
130
TABLE 13
STANDARD SIZES AND LENGTHS
Standard Lengthsa,b,c
All Classifications except

Standard Sizes, E7020-A1, E7020-G, E7020-A1, E7020-G,
(Core Wire Diameter)d E7027-A1 and E7027-G E7027-A1 and E7027-G
in. mm in. mm in. mm

3 e e
32 (0.093) 2.4 12 or 14 300 or 350 12 300
1
8 (0.125) 3.2 14 350 14 350
5
32 (0.156) 4.0 14 350 14 350
3
16 (0.187) 4.8 14 350 14 or 18 350 or 450
7 e
32 (0.218) 5.6e 14 or 18 350 or 450 18 or 28 450 or 700
1 e
4 (0.250) 6.4e 18 450 18 or 28 450 or 700
5 e
16 (0.312) 8.0e 18 or 28 450 or 700
NOTES:
a. Tolerance on the length shall be 14 in. (10 mm).
b. In all cases, end gripping is standard.
c. Other lengths are acceptable and shall be as agreed upon by the supplier and purchaser.
d. Tolerance on the core wire diameter shall be 0.002 in. (0.05 mm). Electrodes produced in sizes other than those shown may be classified.
See Note c of Table 5.
e. These diameters are not manufactured in all electrode classifications (see Table 5).
3
16 in. (4.8 mm) and larger sizes, to provide for 21.3 The ink used for imprinting shall provide suffi-
electrical contact with the electrode holder. cient contrast with the electrode covering so that, in
normal use, the numbers and letters are legible both
20.2 The arc end of each electrode shall be sufficiently before and after welding.
bare and the covering sufficiently tapered to permit
easy striking of the arc. The length of the bare portion 21.4 The prefix letter E in the electrode classifica-
(measured from the end of the core wire to the location tion may be omitted from the designation imprint.
where the full cross-section of the covering is obtained)
shall not exceed 18 in. (3.2 mm) or the diameter of
22. Packaging
the core wire, whichever is less. Electrodes with chipped
coverings near the arc end, baring the core wire no 22.1 Electrodes shall be suitably packaged to protect
more than the lesser of 14 in. (6.4 mm) or twice the them from damage during shipment and storage under
diameter of the core wire, meet the requirements of normal conditions. When electrodes are packaged in
this specification provided no chip uncovers more than hermetically-sealed containers, the type of hermetically-
50 percent of the circumference of the core. sealed container shall be capable of passing the test
specified in 22.2.
22.2 For test, a representative container shall be
21. Electrode Identification immersed in water that has been heated to a temperature
All electrodes shall be identified as follows: of at least 50F (28C) above that of the packaged
material (room temperature). The container shall be
21.1 At least one imprint of the electrode designation immersed so that the surface under observation is 1
(classification plus any optional designators) shall be in. (25 mm) below the water level and the greatest
applied to the electrode covering in the order specified basic dimension is parallel to the water surface. A
in Fig. 12 within 212 in. (65 mm) of the grip end of container with a steady stream of bubbles that lasts
the electrode. for 30 seconds or more does not meet the requirements
of the specification.
21.2 The numbers and letters of the imprint shall
be of bold block type of a size large enough to be 22.3 Standard package weights shall be as agreed
legible. between purchaser and supplier.
131
FIG. 12 ORDER OF ELECTRODE MANDATORY AND OPTIONAL SUPPLEMENTAL DESIGNATORS
132
23. Marking of Packages ARC RAYS can injure eyes and burn skin.
ELECTRIC SHOCK can kill.
23.1 The following product information (as a mini-
W Before use, read and understand the manufacturers
mum) shall be legibly marked on the outside of each
instructions, Material Safety Data Sheets (MSDSs),
unit package:
and your employers safety practices.
(1) AWS specification (year of issue may be ex-
W Keep your head out of the fumes.
cluded) and electrode designation (classification plus
W Use enough ventilation, exhaust at the arc, or both,
any optional supplemental designators)
to keep fumes and gases away from your breathing
(2) Suppliers name and trade designation zone and the general area.
(3) Size and net weight W Wear correct eye, ear, and body protection.
(4) Lot, control, or heat number W Do not touch electrical parts.
23.2 The following precautionary information (as a W See American National Standard Z49.1, Safety in
minimum) shall be prominently displayed in legible Welding and Cutting, published by the American
print on all packages of electrode, including individual Welding Society, 550 N.W. LeJeune Road, Miami,
unit packages enclosed within a larger package: Florida 33126; OSHA Safety and Health Standards,
29 CFR 1910, available from the U.S. Government
WARNING: Protect yourself and others. Read Printing Office, Washington, DC 20402.
and understand this information.
FUMES AND GASES can be dangerous to your
health. DO NOT REMOVE THIS INFORMATION
133
Annex
Guide to AWS Specification for Low-Alloy Steel
Electrodes for Shielded Metal Arc Welding
(This Annex is not a part of AWS A5.5-96, Specification for Low Alloy Steel Electrodes for Shielded Metal Arc Welding, but is
included for information purposes only.)
A1. Introduction a hyphen from the tensile strength and usability designa-
tors, and by a second hyphen, if necessary, from any
This guide is appended to the specification as a
optional supplemental designators which are not part
source of information. The guide is not mandatory and
of the classification designation. This composition desig-
does not form a part of the specification. This guide
nator, such as A1, B3, or W1, immediately identifies
was designed to correlate the covered electrode classifi-
the classification as different from those in ANSI/AWS
cations with the intended applications so the specifica-
A5.1, Specification for Carbon Steel Electrodes for
tion can be used effectively. Such correlations are
Shielded Metal Arc Welding. The composition designa-
intended as examples rather than complete listings of
tor identifies the chemical composition of the weld
the base metals for which each filler metal is suitable.
metal as specified in Table 2. For example, an A1
composition designator identifies the electrode as one
A2. Classification System that produces carbon-molybdenum steel weld metal,
when the electrode is deposited using shielded metal
A2.1 The system for electrode classification in this arc welding.
specification follows the standard pattern used in other
AWS filler metal specifications. The letter E at the
beginning of each classification designation stands for A2.2 G Classifications
electrode. The first two (or three) digits, 70 (or 110),
for example, designate tensile strength of at least 70 A2.2.1 The specification includes filler metals clas-
(or 110) ksi of the weld metal, welded and postweld sified as E(X)XXYY-G. The G indicates that the
heat treated (if required) in accordance with the test filler metal is of a general classification. It is general
assembly preparation section of this specification. The because not all of the particular requirements specified
third (or fourth) digit designates position usability that for each of the other classifications are specified for
will allow satisfactory welds to be produced with the this classification. The intent, in establishing this classi-
electrode. Thus, the 1, as in E7018-C2L (or fication, is to provide a means by which filler metals
E11018M), means that the electrode is usable in all that differ in one respect or another (chemical composi-
positions (flat, horizontal, vertical, and overhead). The tion, for example) from all other classifications (meaning
2, as in E7020-A1, designates that the electrode is that the composition of the filler metalin the case
suitable for use in the flat position and for making of the exampledoes not meet the composition speci-
fillet welds in the horizontal position. The last two fied for any of the classifications in the specification)
digits taken together designate the type of current with can still be classified according to the specification.
which the electrode can be used and the type of covering The purpose is to allow a useful filler metal, one
on the electrode, as listed in Table 1. that otherwise would have to await a revision of the
With the exception of the military similar electrodes specification, to be classified immediately, under the
[e.g., E(X)XX18M(1)], the classifications in this speci- existing specification. This means, then, that two filler
fication also include a suffix designator, separated by metals, each bearing the same G classification, may
134
be quite different in some certain respect (chemical A2.2.3.3 The request should be sent to the
composition, again, for example). Secretary of the Filler Metal Committee at AWS Head-
quarters. Upon receipt of the request, the Secretary
A2.2.2 The point of difference (although not neces- will do the following:
sarily the amount of difference) referred to above will (a) Assign an identifying number to the request.
be readily apparent from the use of the words not This number will include the date the request was
required and not specified in the specification. The received.
use of these words is as follows: (b) Confirm receipt of the request and give the
Not Specified is used in those areas of the specification identification number to the person who made the
that refer to the results of some particular test. It request.
indicates that the requirements for that test are not (c) Send a copy of the request to the Chairman
specified for that particular classification.
of the Filler Metal Committee and the Chairman of
Not Required is used in those areas of the specification
the particular Subcommittee involved.
that refer to the test that must be conducted in order
(d) File the original request.
to classify a filler metal. It indicates that the test is
not required because the requirements for the test have (e) Add the request to the log of outstanding
not been specified for that particular classification. requests.
Restating the case, when a requirement is not speci-
A2.2.3.4 All necessary action on each request
fied, it is not necessary to conduct the corresponding
will be completed as soon as possible. If more than
test in order to classify a filler metal to that classification.
12 months lapse, the Secretary shall inform the requestor
When a purchaser wants the information provided by
of the status of the request, with copies to the Chairman
that test, in order to consider a particular product of
of the Committee and the Subcommittee. Requests still
that classification for a certain application, the purchaser
outstanding after 18 months shall be considered not to
will have to arrange for that information with the
have been answered in a timely manner and the
supplier of that product. The purchaser will also have
Secretary shall report these to the Chairman of the
to establish with that supplier just what the testing
Filler Metal Committee, for action.
procedure and the acceptance requirements are to be,
for that test. The purchaser may want to incorporate A2.2.3.5 The Secretary shall include a copy of
that information (via ANSI/AWS A5.01, Filler Metal the log of all requests pending and those completed
Procurement Guidelines) in the purchase order. during the preceding year with the agenda for each
Filler Metal Committee meeting. Any other publication
A2.2.3 Request for Filler Metal Classification
of requests that have been completed will be at the
A2.2.3.1 When a filler metal cannot be classified option of the American Welding Society, as deemed
according to some classification other than a G classi- appropriate.
fication, the manufacturer may request that a classifica-
tion be established for that filler metal by using the A2.3 Optional supplemental designators are also used
procedure given here. When the manufacturer elects to in this specification in order to identify electrode classi-
use the G classification, the Filler Metal Committee fications that have met certain supplemental require-
recommends that the manufacturer still request that a ments as agreed to between the supplier and the pur-
classification be established for that filler metal, as long chaser. The optional supplemental designators are not
as the filler metal is of commercial significance. part of the classification nor of its designation.
An optional supplemental designator HZ following
A2.2.3.2 A request to establish a new filler the classification designation, which consists of four
metal classification must be a written request, and it or five digits plus M, or a composition suffix such as
needs to provide sufficient detail to permit the Filler -A1, -B2, or -C2L, indicates an average diffusible
Metal Committee or the Subcommittee to determine hydrogen content of not more than Z mL/100g of
whether a new classification or the modification of an deposited metal when tested in the as-received or
existing classification is more appropriate, and whether conditioned state in accordance with ANSI/AWS A4.3.
either is necessary to satisfy the need. The request See Section 16 and Table 12. Electrodes that are
needs to state the variables and their limits for such designated as meeting the lower, or lowest hydrogen
a classification or modification. The request should limits, as specified in Table 12, also are understood
contain some indication of the time by which completion to be able to meet any higher hydrogen limits. Therefore,
of the new classification or modification is needed. as an example, an electrode designated as H4 also
135
meets H8 and H16 requirements without being A5. Ventilation During Welding
designated as such. The letter R is an example of a
A5.1 Five major factors govern the quantity of
supplemental designator used with certain low-hydrogen
fumes in the atmosphere to which welders and welding
electrode classifications. It identifies classifications that
operators are exposed during welding:
have been exposed to a humid environment for a given
(1) Dimensions of the space in which welding is
length of time and tested for low moisture absorption
done (with special regard to the height of the ceiling)
in addition to the standard moisture test required for
classification of low-hydrogen electrodes. See Note d (2) Number of welders and welding operators work-
to Table 1, as well as Tables 11 and 12. ing in that space
(3) Rate of evolution of fumes, gases, or dust, ac-
cording to the materials and processes used
A3. Acceptance (4) The proximity of welders and welding operators
to the fumes as they issue from the welding zone, and
Acceptance of all welding materials classified under to the gases and dust in the space in which they are
this specification is in accordance with ANSI/AWS working
A5.01, Filler Metal Procurement Guidelines, as the (5) The ventilation provided to the space in which
specification states. Any testing a purchaser requires the welding is done
of the supplier, for material shipped in accordance with
this specification, shall be clearly stated in the purchase A5.2 American National Standard ANSI/ASC Z49.1,
order, according to the provisions of ANSI/AWS A5.01. Safety in Welding, Cutting, and Allied Processes (pub-
In the absence of any such statement in the purchase lished by the American Welding Society), discusses
order, the supplier may ship the material with whatever the ventilation that is required during welding and
testing is normally conducted on material of that classi- should be referred to for details. Attention is drawn
fication, as specified in Schedule F, Table 1, of ANSI/ particularly to the section of that document entitled
AWS A5.01. Testing in accordance with any other Ventilation.
Schedule in that Table must be specifically required
by the purchase order. In such cases, acceptance of
A6. Welding Considerations
the material shipped will be in accordance with those
requirements. A6.1 Weld metal properties may vary widely, ac-
cording to size of the electrode and amperage used,
size of the weld beads, base-metal thickness, joint
A4. Certification geometry, preheat and interpass temperatures, surface
condition, base-metal composition, dilution, etc. Be-
The act of placing the AWS specification and classi-
cause of the profound effect of these variables, a test
fication designations on the packaging enclosing the
procedure was chosen for this specification which would
product, or the classification on the product itself,
represent good welding practice and minimize variation
constitutes the suppliers (manufacturers) certification
of the most potent of these variables.
that the product meets all of the requirements of the
specification. A6.2 It should be recognized, however, that produc-
The only testing requirement implicit in this certification practices may be different. The differences encoun-
tion is that the manufacturer has actually conducted tered may alter the properties of the weld metal. For
the tests required by the specification on material that instance, interpass temperatures may range from sub-
is representative of that being shipped and that the freezing to several hundred degrees. No single tempera-
material met the requirements of the specification. Rep- ture or reasonable range of temperatures can be chosen
resentative material, in this case, is any production for classification tests which would be representative
run of that classification using the same formulation. of all of the conditions encountered in production work.
Certification is not to be construed to mean that tests Properties of production welds may vary accordingly,
of any kind were necessarily conducted on samples of depending on the particular welding conditions.
the specific material shipped. Tests on such material Weld metal properties may not duplicate, or even
may or may not have been made. The basis for the closely approach, the values listed and prescribed for
certification required by the specification is the classifi- test welds. For example, ductility in single pass welds
cation test of representative material cited above, in thick base-metal made outdoors in cold weather
and the Manufacturers Quality Assurance System in without adequate preheating may drop to little more
ANSI/AWS A5.01. than half that required herein and normally obtained.
136
This does not indicate that either the electrodes or the yield and tensile strengths with a decrease in ductility.
welds are below standards in this specification. It The cooling rate can be retarded by utilizing a higher
indicates only that the particular production conditions preheat and interpass temperature. The preheat and
are more severe than the test conditions prescribed by interpass temperature ranges given in Table 7 of this
this specification. specification are adequate for the preparation of the
test assemblies. However, in actual production, users
A6.3 Hydrogen is another factor to be considered are encouraged to test their own procedures to verify
in welding. Weld metals, other than those from low- that they have selected preheat and interpass tempera-
hydrogen electrodes [E(X)XX15-X, E(X)XX16-X, tures which will produce desirable results in production.
E(X)XX18M(1), and E(X)XX18-X], contain significant
quantities of hydrogen for some period of time after A6.6 Heat input usually is measured as Joules per
they have been made. Most of this hydrogen gradually linear inch, J/in. (kJ/cm). However, in this specification
escapes. After two to four weeks at room temperature the heat input is governed in the preparation of the
or in 24 to 48 hours at 200 to 220F (95 to 105C), test assembly by the bead sequence and the total weld
most of it has escaped. As a result of this change in layer count upon completion of the groove weld test
hydrogen content, ductility of the weld metal increases assembly.
towards its inherent value, while yield, tensile, and Heat input will have a significant effect on the
impact strengths remain relatively unchanged. strength levels attained in many of the higher strength
This specification requires aging of the test specimens weld metals produced from the electrode classifications
of cellulosic electrodes at 200 to 220F (95 to 105C) in this specification. For instance, weld metal produced
for 48 hours before subjecting them to tension testing. with E11018M electrode at a 35 000 J/in. (13.8 kJ/
This is done to minimize discrepancies in testing. cm) heat input rate may exceed 110 ksi (760 MPa)
Aging treatments are sometimes used for low-hydrogen yield strength in the as-welded condition and 95 ksi
electrodes, especially when testing high-strength depos- (655 MPa) yield strength after postweld heat treatment.
its. Note that aging may involve holding test specimens On the other hand, if the heat input is raised to 55
at room temperature for several days or holding at 000 J/in. (21.7 kJ/cm), this same electrode will produce
a higher temperature for a shorter period of time. weld metal that does not exceed 110 ksi (760 MPa)
Consequently, users are cautioned to employ adequate as-welded yield strength and after postweld heat treat-
preheat and interpass temperatures to avoid the deleteri- ment may be below 95 ksi (655 MPa) yield strength.
ous effects of hydrogen in production welds. It is, therefore, recommended that, if the user is going
to use either lower or higher heat inputs than normally
A6.4 Welds made with electrodes of the same classi- used for classification testing of electrodes, the user
fications and the same welding procedure will have should test the welding procedure to be used to deter-
significantly different tensile and yield strengths in the mine that the strength levels expected will be attained
as-welded and postweld heat-treated conditions. Even in production. This is especially true if out-of-position
weld metal produced from the same classification and welding is to be performed.
the same welding procedure but with different postweld
heat-treatment holding temperatures or times at holding A6.7 Electrodes which meet all the requirements of
temperatures will have different strength levels. With any given classification may be expected to have similar
the low-alloy steel weld metals produced by the classifi- characteristics. Certain minor differences continue to
cations in this specification, postweld heat treatment can exist from one brand to another due to differences
produce tempering (softening) or secondary hardening of in preferences that exist regarding specific operating
the weld metal. It is recommended that users conduct characteristics.
their own evaluation of the welding procedure to be A6.8 Since the electrodes within a given classification
used in production in order to verify that the weld have similar operating characteristics and mechanical
metal properties obtained in actual production are those properties, the user can usually limit the study of
desired. available electrodes to those within a single classification
after determining which classification best suits the
A6.5 Preheat and interpass minimum temperatures
users particular requirements.
also have a significant effect on the strength levels
attained with certain low-alloy steel weld metals. These A6.9 This specification does not establish values for
weld metals are affected by rapid cooling rates which all characteristics of the electrodes falling within a
tend to produce more martensitic or bainitic microstruc- given classification, but it does establish values to
tures. These microstructures will often exhibit higher measure those of major importance. In some instances,
137
the characteristics are so intangible that no adequate The inclusion of impact requirements for certain elec-
tests are available. This specification does not necessar- trode classifications allows the specification to be used
ily provide all the information needed to determine as a guide in selecting electrodes where low-temperature
which classification will best fulfill a particular need. toughness is required. There can be considerable varia-
Therefore, a discussion of each classification group is tion in the weld-metal toughness unless particular atten-
included in Section A7, Description and Intended Use tion is given to the welding procedure and the prepara-
of Electrodes, to supplement information given else- tion and testing of the specimens. The impact energy
where in the specification. values are for Charpy V-notch (ISO-V) specimens and
should not be confused with values obtained with other
A6.10 Some important tests for measuring major
toughness tests.
electrode characteristics are as follows:
A6.11 Electrode Covering Moisture Content and
A6.10.1 Radiographic Test. Nearly all of the low-
Conditioning
alloy steel electrodes covered by this specification are
capable of producing welds that meet most radiographic A6.11.1 Hydrogen can have adverse effects on
soundness requirements. However, if incorrectly applied, welds in some steels under certain conditions. One
unsound welds may be produced by any of the elec- source of this hydrogen is moisture in the electrode
trodes. For electrodes of some classifications, the radio- coverings. For this reason, the proper storage, treatment,
graphic requirements in Table 9 are not necessarily and handling of electrodes is necessary.
indicative of the average radiographic soundness to be
A6.11.2 Electrodes are manufactured to be within
expected in production use. Electrodes of the
acceptable moisture limits, consistent with the type of
E(X)XX10-X, E(X)XX11-X, and E7020-X classifica-
covering and strength of the weld metal. They are then
tions can be expected to produce acceptable radiographic
normally packaged in a container which has been
results. Under certain conditions, notably in welding
designed to provide the degree of moisture protection
long, continuous joints in relatively thick base metal,
considered necessary for the type of covering involved.
low-hydrogen electrodes of the E(X)XX15-X,
E(X)XX16-X, E(X)XX18M(1), and E(X)XX18-X clas- A6.11.3 If there is a possibility that the noncellu-
sifications will often produce even better results. losic covered electrodes may have absorbed excessive
On the other hand, in joints open to the atmosphere moisture, they may be reconditioned by rebaking. Some
on the root side, at the ends of joints, in joints with electrodes require rebaking at a temperature as high
many stops and starts, and in welds on small diameter as 800F (425C) for approximately 1 to 2 hours. The
pipe or in small, thin, irregularly-shaped joints, the manner in which the electrodes have been produced
low-hydrogen electrodes tend to produce welds of poor and the relative humidity and temperature conditions
radiographic soundness. E(X)XX13-X electrodes usually under which the electrodes are stored determine the
produce the best radiographic soundness in welding proper length of time and temperature used for condi-
small, thin parts. E7027-X electrodes produce welds tioning. Some typical storage and drying conditions are
which may be either quite good or rather inferior in included in Table A1.
radiographic soundness. The tendency seems to be in
A6.11.4 Cellulosic coverings for E(X)XX10-X and
the latter direction.
E(X)XX11-X classifications need moisture levels of 3
A6.10.2 Fillet Weld Test. This test is included to 7 percent for proper operation. Therefore, storage
as a means of demonstrating the usability of an elec- or conditioning above ambient temperature may dry
trode. This test is concerned with the appearance of these electrodes too much and adversely affect their
the weld (i.e., weld face contour and smoothness, operation (see Table A1).
undercut, overlap, size, and resistance to cracking). It
A6.12 Core Wire. The core wire for all the electrodes
also provides an excellent and inexpensive method of
in this specification is usually a steel having a typical
determining the adequacy of fusion at the weld root
composition which may differ significantly from that
(one of the important considerations for an electrode).
of the weld metal produced by the covered electrode.
Test results may be influenced by the level of
welded skill. A6.13 Coverings
A6.10.3 Toughness. Charpy V-notch impact re- A6.13.1 Electrodes of some classifications have
quirements are included in the specification. All classi- substantial quantities of iron powder added to their
fications of electrodes in the specification can produce coverings. The iron powder fuses with the core wire
weld metal of sufficient toughness for many applications. and other metals in the covering, as the electrode melts,
138
TABLE A1
TYPICAL STORAGE AND DRYING CONDITIONS FOR COVERED ARC WELDING ELECTRODES
Storage Conditionsa
AWS Classifications Ambient Air Holding Ovens Drying Conditionsb

EXX10-X
Ambient temperature 100120F (3849C) Not recommended
EXX11-X
EXX13-X 60100F (1638C)

250300F (121149C)
E7020-X 50 percent max relative 100120F (3849C)
1 hour at temperature
E7027-X humidity
EXX15-X
EXX16-X 500800F (260427C)
Not recommendedc 250300F (121149C)
EXX18M(1) 1 hour at temperature
EXX18-X
NOTES:
a. After removal from manufacturers packaging.
b. Because of inherent differences in covering compositions the manufacturer should be consulted for the exact drying conditions.
c. Some of these electrode classifications may be designated as meeting low moisture absorbing requirements. This designation does not imply
that storage in ambient air is recommended.
and is deposited as part of the weld metal, just as is A6.13.4 Low-hydrogen electrodes have mineral
the core wire. Relatively high amperages can be used coverings which are high in calcium carbonate and
since a considerable portion of the electrical energy other ingredients that are low in moisture and organic
passing through the electrode is used to melt the thicker materials and hence low in hydrogen content. Low-
covering containing iron powder. The result is that more hydrogen electrodes were developed for welding low-
weld metal may be obtained from a single electrode with alloy, high-strength steels, some of which were high
iron powder in its covering than from a single electrode in carbon content. Electrodes with other than low-
of the same size without iron powder. hydrogen coverings may produce hydrogen induced
cracking in those steels.
A6.13.2 Due to the thick covering and deep cup Underbead cracks occur in the base metal, usually
produced at the arcing end of the electrode, iron powder just below the weld bead. Weld cracks also may occur.
electrodes can be used very effectively with a drag These cracks are caused by the hydrogen absorbed
technique. This technique consists of keeping the elec- from the arc atmosphere. Although these cracks do not
trode covering in contact with the workpiece at all generally occur in carbon steels which have a low
times, which makes for easy handling. However, a carbon content, they may occur when welding higher
technique using a short arc length is preferable if the carbon or low-alloy steels with other than low-hydrogen
3
32 in. (2.4 mm) or 18 in. (3.2 mm) electrodes are to electrodes and without precautions, such as, increased
be used in other than flat or horizontal fillet welding preheat temperatures and postweld heating. For more
positions or for making groove welds. information on special tests for low-hydrogen electrodes,
see Sections 15 and 16 in the specification and A9.2
A6.13.3 The E70YY-X electrodes were included and A9.3 in this Annex.
in this specification to recognize the lowest strength A6.14 Amperage Ranges. Table A2 gives amperage
levels obtained with low-alloy steel electrodes, as well ranges which are satisfactory for most classifications.
as, to recognize the industry demand for low-alloy When welding in the vertical position with upward
electrodes with 70 ksi (480 MPa) minimum tensile progression, currents near the lower limit of the range
strength. Unlike the E70YY classifications in ANSI/ are generally used.
AWS A5.1, Specification for Carbon Steel Electrodes
for Shielded Metal Arc Welding, these electrodes do
A7. Description and Intended Use of Electrodes
contain deliberate alloy additions, and some are required
to meet minimum tensile properties after postweld heat A7.1 Chemical Composition. The chemical composi-
treatment. tion of the weld metal produced is often the primary
139
TABLE A2
TYPICAL AMPERAGE RANGES
Electrode Diameter
EXX10-X EXX15-X EXX18M(1)
in. mm and EXX11-X EXX13-X E7020-X E7027-X and EXX16-X and EXX18-X
3
32 2.4 40 to 80 45 to 90 65 to 110 70 to 100
1
8 3.2 75 to 125 80 to 130 100 to 150 125 to 185 100 to 150 115 to 165
5
32 4.0 110 to 170 105 to 180 130 to 190 160 to 240 140 to 200 150 to 200
3
16 4.8 140 to 215 150 to 230 175 to 250 210 to 300 180 to 255 200 to 275
7
32 5.6 170 to 250 225 to 310 250 to 350 240 to 320 260 to 340
1
4 6.4 210 to 320 275 to 375 300 to 420 300 to 390 315 to 400
5
16 8.0 375 to 475
consideration for electrode selection. Together with toughness of the weld metal. Typical applications in-
appropriate heat treatments, each composition can clude the welding of C-Mo steel base metals such as
achieve a wide range of corrosion resistance and me- ASTM A204 plate and A335-P1 pipe.
chanical properties at various service temperatures. It
is usually desirable for weld metal to match the chemical A7.1.2 EX01Y-BX and EX01Y-BXL (Cr-Mo
composition and the mechanical properties of the base Steel) Electrodes. These low-hydrogen electrodes pro-
metal as closely as possible. In fact, many of the duce weld metal that contains between 12% and 9%
electrodes classified to this specification have been chromium and between 12% to 1% molybdenum. They
developed for specific base-metal grades or classes. If are designed to produce weld metal for high-temperature
an optimum match is not possible, engineering judgment service and for matching the properties of the typical
together with weld testing may be required to select base metals as shown in Table A3.
the most suitable electrodes. For many of these Cr-Mo electrode classifications,
Table 2 provides detailed weld metal chemical com- low carbon EXX1Y-BXL classifications have been es-
position requirements for each electrode classification. tablished. While regular Cr-Mo electrodes produce weld
Tables 3 and 4 list the mechanical properties of the metal with about 0.08% carbon, the L-Grades are
weld metal when the electrode is used in the flat limited to a maximum of 0.05% carbon. While the
downhand position, and the weldment is subjected to lower percent carbon in the weld metal will improve
the postweld heat-treatment (PWHT) requirements in ductility and lower hardness, it will also reduce the
Tables 3 and 7. Is should be noted that changes in high-temperature strength and creep resistance of the
welding position, welding variables, or heat treatment weld metal.
can be expected to affect the mechanical properties. Since all Cr-Mo electrodes produce weld metal which
However, except for the effects of dilution, the chemical will harden in still air, both preheat and PWHT are
composition can be expected to remain reasonably required for most applications.
unchanged. No minimum notch toughness requirements have
The suffixes, which are part of each alloy electrode been established for any of the Cr-Mo electrode classifi-
classification, identify the chemical composition of the cations. While it is possible to obtain Cr-Mo electrodes
weld metal produced by the electrode. The following with minimum toughness values at ambient temperatures
paragraphs highlight the differences between these elec- down to 32F (0C), specific values and testing must
trodes and electrode groups and indicate typical applica- be agreed to by the supplier and the purchaser.
tions.
A7.1.2.1 E701Y-B2L and E801Y-B3L Elec-
A7.1.1 E70YY-A1 (C-Mo Steel) Electrodes. trodes. In previous revisions of ANSI/AWS A5.5,
These electrodes are similar to the E70YY carbon steel electrodes classified in this standard as E701Y-B2L
electrodes classified in ANSI/AWS A5.1, except that were classified as E801Y-B2L. Likewise, electrodes
1
2% molybdenum has been added. This addition in- herein classified as E801Y-B3L were classified as
creases the strength of the weld metal, especially at E901Y-B3L. The composition ranges were not changed
elevated temperatures, and provides some increase in from A5.5-81 to this standard for the corresponding
corrosion resistance; however, it may reduce the notch classifications. The strength designations and room tem-
140
TABLE A3
TYPICAL BASE METAL APPLICATIONS FOR Cr-Mo STEEL ELECTRODES
AWS Classification %Cr %Mo Typical Base Metals

1 1
E701Y-B2L 1 4 2 Thin wall A335-P11 Pipe or tube for use in the as-welded condition, A588 Plate for
weathering applications where toughness is not a requirement
1 1
E801Y-B1 2 2 A335-P2 Pipe, A387 Gr. 2 Plate
1 1
E801Y-B2 1 4 2 A335-P11 Pipe, A387 Gr. 11 Plate
1
E801Y-B3L 2 4 1 Thin wall A335-P22 Pipe for use in the as-welded condition
1
E901Y-B3 2 4 1 A335-P22 Pipe, A387 Gr. 22 Plate
1
E8015-B4L 2 2 A213-87 Gr. T3b Tube*
1
E8016-B5 2 1 A356-58T Grs. 3 or 4 Castings*
1
E801Y-B6 5 2 A213-T5 Tube, A335-P5 Pipe
1
E901Y-B9 9 1 A213-T91 Tube, A335-P91 Pipe, A387 Gr. 91 Plate
NOTE:
Base metals followed by an asterisk (*) are no longer listed as grades in the current ASTM specification.
perature strength requirements after postweld heat-treat- ture creep strength properties should be determined.
ment have been reduced to reflect the fact that commer- Due to the influence of various levels of carbon and
cial products have been producing marginal tensile niobium (columbium), specific values and testing must
strength results in classification tests over many years. be agreed to by the purchaser and supplier.
The base metals with which these classifications are
generally used have lower strength requirements than A7.1.3 EX01Y-CX and EX01Y-CXL (Ni Steel)
were reflected by the former electrode classifications. Electrodes. These low-hydrogen electrodes have been
Therefore, unless the higher strength indicated by the designed to produce weld metal with increased strength
former classifications of these electrodes is specifically without being air-hardenable or with increased notch
necessary for a particular welding procedure, the E701Y- toughness at temperatures as low as 175F (115C).
B2L classifications of this standard should be considered They have been specified with nickel contents which
as identical to the corresponding E801Y-B2L classifica- fall into five nominal levels of 1% Ni, 112% Ni, 212%
tions of A5.5-81. Likewise, the E801Y-B3L classifica- Ni, 312% Ni, and 612% Ni in steel.
tions of this standard should be considered as identical With carbon levels of up to 0.12%, strength increases
to the E901Y-B3L classifications of A5.5-81. and permits these Ni steel electrodes to be classified
as E801Y-CX. However, with lower levels of carbon,
A7.1.2.2 E901Y-B9 Electrodes. E901Y-B9 is low-temperature toughness improves to match the base-
a 9% Cr - 1% Mo, low-hydrogen electrode modified metal properties of nickel steels, such as ASTM A203
with niobium (columbium) and vanadium designed to Gr. E, ASTM A352 LC3 and LC4 classifications. Thus,
provide improved creep strength, toughness, fatigue the intended application and the needed mechanical
life, and oxidation and corrosion resistance at elevated properties determine whether or not L-Grades should
temperatures. Due to the higher elevated temperature be selected.
properties of this alloy, components that are now fabri- Many low-alloy steels require postweld heat treatment
cated from stainless and ferritic steels may be fabricated to stress relieve the weld or temper the weld metal
from a single alloy, eliminating problems associated and heat-affected zone to achieve increased ductility.
with dissimilar welds. It is often acceptable to exceed the PWHT holding
In addition to the classification requirements in this temperatures shown in Table 7. However, for many
specification, either impact toughness or high tempera- applications, nickel steel weld metal can be used without
141
postweld heat treatment. If PWHT is to be specified at temperatures ranging from 0F to 60F (18C to
for a nickel steel weldment, the holding temperature 51C). With these properties, the E(X)X01YM(1) type
should not exceed the maximum temperature given in electrodes are suitable for joining many high-strength,
Table 7 for the classification considered since nickel low-alloy or microalloyed steels to themselves or to
steels can be embrittled at higher temperatures. lower strength steels, including carbon steels.
A7.1.4 E8018-NM1 (Ni-Mo Steel) Electrodes. A7.1.8 EX010-P1 (Pipeline) Electrodes. These
This low-hydrogen electrode, which contains about 1% electrodes have been designed primarily for welding
nickel and 12% molybdenum, is similar to the Mn-Mo typical high-strength, pipe butt joints in the vertical
steel electrodes discussed in A7.1.5. However, this welding position with downward or upward progression.
electrode can often be welded without PWHT, but the With their cellulosic coverings, they produce deep
resulting strength and notch toughness are lower than penetrating, spray-type welding arcs and thin, easily
the values obtained with Mn-Mo electrodes. Some removable slag. This combination is best suited for
typical applications include the welding of high-strength, achieving full penetration and radiographic quality for
low-alloy or microalloyed structural steels. the downhill welding of butt joints when the axis of
A7.1.5 E(X)X01Y-DX (Mn-Mo Steel) Electrodes. the pipe is in the horizontal position.
These low-hydrogen electrodes produce weld metal While weld metals produced from these electrodes
which contains about 112% manganese and between do not have any minimum chemical composition re-
1
3 and 23% molybdenum. This weld metal provides quirements, the supplier must provide sufficient alloying
higher strength and better notch toughness than the C- elements to meet the increased mechanical property
1
2% Mo and 1% Ni-12% Mo steel weld metal discussed requirements. Special emphasis must be placed upon the
in A7.1.1 and A7.1.4. However, the weld metal from minimum yield strength values, since most transmission
these Mn-Mo steel electrodes is quite air-hardenable pipeline materials and systems are designed to yield
and usually requires preheat and PWHT. The individual strength limits. Typical application for E7010-P1 and
electrodes classified under this electrode group have E8010-P1 electrodes is the welding of API-5L-X52 and
been designed to match the mechanical properties and API-5L-X65 piping assemblies, respectively.
corrosion resistance of the high-strength, low-alloy pres-
A7.1.9 EX018-WX (Weathering Steel) Elec-
sure vessel steels, such as ASTM A302 Gr. B.
trodes. These low-hydrogen electrodes have been de-
A7.1.6 E(X)XXYY-G (General Low-Alloy Steel) signed to produce weld metal that matches the corrosion
Electrodes. These electrodes are described in A2.2. resistance and the coloring of the ASTM weathering-
These electrode classifications may be either modifica- type structural steels. These special properties are
tions of other discrete classifications or totally new achieved by the addition of about 12% copper to the
classifications. Purchaser and user should determine weld metal. To meet strength, ductility, and notch
from the supplier what the description and intended toughness in the weld metal, some chromium and nickel
use of the electrode is. additions are also made. These electrodes are used to
weld the typical weathering steel, such as ASTM A242
A7.1.7 E(X)X01YM(1) (Military Similar) Elec-
and A588.
trodes. These low-hydrogen electrodes were originally
designed for military applications such as welding HY80
and HY100 type steels. To achieve desired weld-metal
properties and soundness, these electrodes have small A8. Modification of Moisture Test Apparatus
alloy additions (especially some Ni) and require careful A8.1 Some laboratories have modified test apparatus
control of moisture in the electrode covering and from for determining the moisture content of electrode cov-
other sources of hydrogen. The latter must be maintained erings. The following are some of the modifications
during electrode fabrication, packaging, transport, and which have been successfully used:
site storage.
These electrodes are usually employed without subse- A8.1.1 This specification recommends that only
quent postweld-heat treatment. However, hydrogen-re- nickel boats be used rather than clay boats because
lease treatments at lower temperatures (typically less lower blank values can be obtained. Some laboratories
than 500F) are often applied. In the as-welded condi- use zirconium silicate combustion tubes in preference
tion, the weld-metal mechanical properties include ulti- to fused silica or mullite because zirconium silicate
mate tensile strength minimums ranging from 90 to will not devitrify or allow the escape of combustible
120 ksi (620 to 830 MPa) and good notch toughness gases at temperatures up to 2500F (1370C).
142
Some combustion tubes are reduced at the exit end, compounds (such as machining oil) in the arc causes
and a separate dust trap is used. This dust trap consists cracking. Accordingly, the use of optional designators
of a 200 mm drying tube filled with glass wool which for diffusible hydrogen is introduced to indicate the
is inserted between the Schwartz absorption U-tube and maximum average value obtained under a clearly defined
the combustion tube. A suitable 300F (149C) heater test condition in ANSI/AWS A4.3, Standard Methods
is mounted around the dust trap to keep evolved water for Determination of the Diffusible Hydrogen Content
from condensing in the trap. The dust trap is filled of Martensitic, Bainitic, and Ferritic Steel Weld Metal
with glass wool which can be easily inspected to Produced by Arc Welding.
determine when the glass wool should be replaced. An The user of this information is cautioned that actual
extra spray trap may be installed downstream of the welding conditions may result in different diffusible
absorption U-tube to ensure that the concentrated sulfu- hydrogen values than those indicated by the designator.
ric acid in the gas-sealing bottle is not accidentally The use of a reference atmospheric condition during
drawn into the absorption U-tube. welding is necessary because the arc always is imper-
fectly shielded. Moisture from the air, distinct from
A8.1.2 On the entrance end of the combustion
that in the covering, can enter the arc and subsequently
tube, a pusher rod can be used consisting of a 18 in.
the weld pool, contributing to the resulting observed
(3.2 mm) stainless steel rod mounted in a 14 in. (6.4
diffusible hydrogen. This effect can be minimized by
mm) copper tee fitting. This is used at the entrance
maintaining as short an arc length as possible consistent
of the combustion tube and permits gradual introduction
with a steady arc. Experience has shown that the effect
of the sample into the tube while oxygen is passing
of arc length is minor at the H16 level, but is very
over the sample. In this way, any free moisture will
significant at the H4 level. An electrode meeting the
not be lost, which can happen if the sample is introduced
H4 requirement under the reference atmospheric condi-
directly into the hot zone before closing the end of
tion may not do so under conditions of higher humidity
the tube.
at the time of welding. This is especially true if a
long arc is maintained.
A9. Special Tests The reference atmospheric condition during welding
of the test assembly is 10 grains of water vapor per
A9.1 It is recognized that supplementary tests may
pound (1.43 g/kg) of dry air. This corresponds to 70F
be necessary to determine the suitability of these welding
(21C) and 10% R.H. on a standard psychometric chart
electrodes for applications involving properties not con-
at 29.92 in. Hg (760 mm) barometric pressure. Actual
sidered in this specification. In such cases, additional
conditions, measured using a sling psychrometer or
tests to determine specific properties, such as hardness,
other suitable device, that equal or exceed this reference
corrosion resistance, mechanical properties at higher
condition provide assurance that the conditions during
or lower service temperatures, wear resistance, and
welding will not diminish the final results of the test.
suitability for welding combinations of dissimilar metals,
may need to be conducted.
A9.3 Absorbed Moisture Test. The development of
A9.2 Diffusible Hydrogen Test. Hydrogen induced low-hydrogen electrode coverings that resist moisture
cracking of weld metal and the heat-affected zone can absorption during exposure to humid air is a recent
be encountered in low-alloy steels welded by the filler improvement in covered electrode technology. Not all
metals covered by this specification. Therefore, many commercial low-hydrogen electrodes possess this char-
of the electrode classifications in this specification are acteristic. To assess this characteristic, the absorbed
the low-hydrogen type. The diffusible hydrogen test moisture test described in Section 15 was devised. The
is reintroduced into this specification as an optional exposure conditions selected for the test are arbitrary.
supplemental test for low-hydrogen electrodes. How- Other conditions may yield quite different results.
ever, the diffusible hydrogen test today is considerably A task group of the AWS A5A Subcommittee evalu-
improved over the former glycerin test, which appeared ated this test and concluded that it can successfully
first in the original issue of AWS A5.5-48. differentiate moisture-resistant electrodes from those
The covering moisture test has proved a satisfactory which are not. The task group also observed considerable
test over many years as a means of assessing the degree variability of coating moisture results after exposure
of care needed to avoid hydrogen induced cracking. of electrodes in cooperative testing among several labo-
This is, however, an indirect test. Moisture itself does ratories. The precision of the test is such that, with
not cause cracking, but the diffusible hydrogen that moisture-resistant electrodes from a single lot, the partic-
forms from the moisture and other hydrogen containing ipating laboratories could observe exposed covering
143
moisture values ranging, for example, from 0.15% or cutting of unusually thick base metal is involved, sheet-
less to 0.35% or more. The cause of this variability metal shields should be used for extra protection.
is uncertain at present, but is considered by the task Mechanization of highly hazardous processes or jobs
group to be related to variations in the exposure condi- should be considered.
tions. Because of this variability, the task group con- Other personnel in the work area should be protected
cluded that it is not realistic to set a limit for covering by the use of noncombustible screens or by the use
moisture of exposed moisture-resistant electrodes lower of appropriate protection as described in the previous
than 0.4% at this time. paragraph. Before leaving a work area, hot workpieces
should be marked to alert other persons of this hazard.
No attempt should be made to repair or disconnect
A10. Discontinued Classifications
electrical equipment when it is under load. Discon-
A number of electrode classifications have been nection under load produces arcing of the contacts and
discontinued during the numerous revisions of this may cause burns or shock, or both. (Note: Burns can
specification, reflecting either changes in commercial be caused by touching hot equipment such as electrode
practice, or changes in the classification system used holders, tips, and nozzles. Therefore, insulated gloves
in the specification. These discontinued electrode classi- should be worn when these items are handled, unless
fications are listed in Table A4, along with the year an adequate cooling period has been allowed before
they were last published in this specification. Some touching.)
discontinued electrode classifications continue to be The following sources are for more detailed informa-
applied to products even though they have been discon- tion on personal protection:
tinued from the specification. In this case, the referenced (1) American National Standards Institute. ANSI/
specification year should be the last year that the ASC Z41.1, Safety-Toe Footwear. New York: American
classification was published in the specification unless National Standards Institute.
the classification was transferred to another current (2) . ANSI/ASC Z49.1, Safety in Welding and
AWS filler metal specification. Cutting. Miami, FL: American Welding Society.
(3) . ANSI/ASC Z87.1, Practice for Occupational
A11. Safety Considerations and Educational Eye and Face Protection. New York:
American National Standards Institute.
A11.1 Burn Protection. Molten metal, sparks, slag, (4) Occupational Safety and Health Administration.
and hot-work surfaces are produced by welding, cutting, Code of Federal Regulations, Title 29 Labor, Chapter
and allied processes. These can cause burns if precau- XVII, Part 1910. Washington, D.C.: U. S. Government
tionary measures are not used. Workers should wear Printing Office.5
protective clothing made of fire-resistant material. Pant
cuffs, open pockets, or other places on clothing that A11.2 Electrical Hazards. Electric shock can kill;
can catch and retain molten metal or sparks should however, it can be avoided. Live electrical parts should
not be worn. High-top shoes or leather leggings and not be touched. The manufacturers instructions and
fire-resistant gloves should be worn. Pant legs should recommended safe practices should be read and under-
be worn over the outside of high-top shoes. Helmets stood. Faulty installation, improper grounding, and in-
or hand shields that provide protection for the face, correct operation and maintenance of electrical equip-
neck, and ears, and a head covering to protect the ment are all sources of danger.
head should be used. In addition, appropriate eye protec- All electrical equipment and the workpieces should
tion should be used. be grounded. The workpiece lead is not a ground lead.
When welding overhead or in confined spaces, ear It is used only to complete the welding circuit. A
plugs to prevent weld spatter from entering the ear separate connection is required to ground the workpiece.
canal should be worn in combination with goggles or The workpiece should not be mistaken for a ground
equivalent to give added eye protection. Clothing should connection.
be kept free of grease and oil. Combustible materials The correct cable size should be used, since sustained
should not be carried in pockets. If any combustible overloading will cause cable failure and result in possi-
substance has been spilled on clothing, a change to ble electrical shock or fire hazard. All electrical connec-
clean, fire resistant clothing should be made before tions should be tight, clean, and dry. Poor connections
working with open arcs or flame. Aprons, cape-sleeves,
leggings, and shoulder covers with bibs designed for 5
OSHA documents are available from U. S. Government Printing
welding service should be used. Where welding or Office, Washington, D.C. 20402
144
TABLE A4
DISCONTINUED ELECTRODE CLASSIFICATIONSa
Last A5.5 (ASTM A316) Last A5.5 (ASTM A316)
AWS Classification Publication Date Classification Publication Date
E7010b 1954 E10026 1948
E7011b 1954 E10030 1948
E7013 1948 E12015b 1954
E7015c 1954 E12016b 1954
E7016c 1954 E7015-C1 1954
E7020b 1954 E7016-C1 1954
E7025 1948 E7015-C2 1954
E7026 1948 E7016-C2 1954
E7030 1948 E9010-B3 1954
E8010b 1954 E9011-B3 1954
E8011b 1954 E9013-B3 1954
E8013b 1954 E8010-B1 1958
E8015b 1954 E8011-B1 1958
E8016b 1954 E8013-B1 1958
E8020 1948 E8015-B1 1958
E8025 1948 E8010-B2 1958
E8026 1948 E8011-B2 1958
E8030 1948 E8013-B2 1958
E9010b 1954 E8015-B2 1958
E9011b 1954 E8015-B4 1958
E9013b 1954 E8016-B4 1958
E9015b 1954 E8018-B4 1958
E9016b 1954 E8015-C1 1958
E9020 1948 E8015-C2 1958
E9025 1948 E8015-C3 1958
E9026 1948 E9016-D1 1958
E9030 1948 E7018-Wd 1981
E10010b 1954 E8015-B2Le 1981
E10011b 1954 E8018-B2Le 1981
E10013b 1954 E8018-NMf 1981
E10015b 1954 E8018-Wd 1981
E10016b 1954 E9015-B3Le 1981
E10020 1948 E9018-B3Le 1981
E10025 1948
NOTES:
a. See Section A10, Discontinued Classifications (in the Annex), for information on discontinued classifications and how they may be used.
b. The higher tensile strength electrode classifications without chemistry requirements for classifications were discontinued in 1958 and replaced
with the G classifications in order to permit a single classification system with chemistry requirements.
c. Both E7015 and E7016 classifications were transferred to AWS A5.1-58T and continue to be included in the current revision of that
specification.
d. Both E7018-W and E8018-W classification designations have been changed to E7018-W1 and E8018-W2 in order to permit the suffix
designator to differentiate between the two chemical compositions of undiluted weld metal.
e. These Cr-Mo electrode classifications were down graded to reflect a more realistic minimum tensile strength for low-carbon chromium-
molybdenum steel weld metal. This change may or may not show a corresponding reduction in creep strength of the weld metal depending
on how the chemical composition of the weld metal is controlled.
f. The E8018-NM classification has been changed to E8018-NM1 to allow for other possible Ni-Mo steel electrode classifications in future
revisions.
145
can overheat and even melt. Further, they can produce as nausea, headaches, dizziness, and metal fume fever.
dangerous arcs and sparks. Water, grease, or dirt should The possibility of more serious health effects exists
not be allowed to accumulate on plugs, sockets, or when especially toxic materials are involved. In confined
electrical units. Moisture can conduct electricity. spaces, the shielding gases and fumes might displace
To prevent shock, the work area, equipment, and breathing air and cause asphyxiation. Ones head should
clothing should be kept dry at all times. Welders should always be kept out of the fumes. Sufficient ventilation,
wear dry gloves and rubber-soled shoes, or stand on a exhaust at the arc, or both, should be used to keep
dry board or insulated platform. Cables and connections fumes and gases from your breathing zone and the
should be kept in good condition. Improper or worn general area.
electrical connections may create conditions that could In some cases, natural air movement will provide
cause electrical shock or short circuits. Worn, damaged, enough ventilation. Where ventilation may be question-
or bare cables should not be used. Open-circuit voltage able, air sampling should be used to determine if
should be avoided. When several welders are working corrective measures should be applied.
with arcs of different polarities, or when a number of Special precautions should be used when welding
alternating current machines are being used, the open-
with the electrodes of the B3, B4, B6, B7, B8, and
circuit voltages can be additive. The added voltages
B9 series. As a group, the fumes from the normal
increase the severity of the shock hazard.
use of these electrodes contain significant amounts of
In case of electric shock, the power should be turned
hexavalent chromium (Cr VI) compounds. The permissi-
off. If the rescuer must resort to pulling the victim
ble exposure limit (PEL) and the threshold limit value
from the live contact, nonconducting materials should
be used. If the victim is not breathing, cardiopulmonary (TLV) for Cr VI of 0.05 mg/m3 as chromium will be
resuscitation (CPR) should be administered as soon as exceeded before reaching the 5.0 mg/m3 threshold limit
contact with the electrical source is broken. A physician value for general welding fume. Therefore, for these
should be called and CPR continued until breathing products, monitoring for hexavalent chromium will be
has been restored, or until a physician has arrived. more conservative than monitoring for general welding
Electrical burns are treated as thermal burns; that is, fume. Short-term effects of excessive overexposure to
clean, cold (iced) compresses should be applied. Con- chromium VI present in fumes may be irritation of
tamination should be avoided; the area should be cov- the breathing system. Some people may have allergic
ered with a clean, dry dressing; and the patient should reactions. Chromium VI is considered a carcinogen by
be transported to medical assistance. the International Agency for Research on Cancer (IARC)
Recognized safety standards such as ANSI/ASC and the National Toxicology Program (NTP). However,
Z49.1, Safety in Welding and Cutting, and NFPA No. evidence from studies involving welding fumes and
70, National Electrical Code, available from National gases containing chromium compounds do not confirm
Fire Protection Association, Batterymarch Park, Quincy, any carcinogenic risk when exposures are held within
MA 02269, should be followed. OSHA mandated limits.
More detailed information on fumes and gases pro-
A11.3 Fumes and Gases. Many welding, cutting, duced by the various welding processes may be found
and allied processes produce fumes and gases which in the following:
may be harmful to health. Fumes are solid particles (1) The permissible exposure limits required by
which originate from welding filler metals and fluxes, OSHA can be found in Code of Federal Regulations,
the base metal, and any coatings present on the base Title 29, Chapter XVII, Part 1910.
metal. Gases are produced during the welding process
(2) The recommended threshold limit values for
or may be produced by the effects of process radiation
fumes and gases may be found in Threshold Limit
on the surrounding environment. Management personnel
and welders alike should be aware of the effects of Values for Chemical Substances and Physical Agents in
these fumes and gases. The amount and composition the Workroom Environment, published by the American
of these fumes and gases depend upon the composition Conference of Governmental Industrial Hygienists
of the filler metal and base metal, welding process, (ACGIH), 6550 Glenway Avenue, Building D-5, Cincin-
current level, arc length, and other factors. nati, OH 45211.
The possible effects of over-exposure range from (3) The results of an AWS-funded study are available
irritation of eyes, skin, and respiratory system to more in a report entitled, Fumes and Gases in the Welding
severe complications. Effects may occur immediately Environment, available from the American Welding
or at some later time. Fumes can cause symptoms such Society.
146
(4) Manufacturers Material Safety Data Sheet for (4) Screens, curtains, or adequate distance from
the product. aisles, walkways, etc., should be used to avoid exposing
passersby to welding operations.
A11.4 Radiation. Welding, cutting, and allied opera- (5) Safety glasses with UV protective side shields
tions may produce radiant energy (radiation) harmful have been shown to provide some beneficial protection
to health. One should become acquainted with the from ultraviolet radiation produced by welding arcs.
effects of this radiant energy.
Radiant energy may be ionizing (such as x-rays), or
nonionizing (such as ultraviolet, visible light, or infra-
red). Radiation can produce a variety of effects such A11.4.3 Ionizing radiation information sources in-
as skin burns and eye damage, depending on the radiant clude the following:
energys wavelength and intensity, if excessive exposure (1) ANSI/AWS F2.1-78, Recommended Safe Prac-
occurs. tices for Electron Beam Welding and Cutting, available
from the American Welding Society.
A11.4.1 Ionizing Radiation. Ionizing radiation is (2) Manufacturers product information literature.
produced by the electron beam welding process. It is
ordinarily controlled within acceptance limits by use
of suitable shielding enclosing the welding area. A11.4.4 The following include nonionizing radia-
tion information sources:
A11.4.2 Nonionizing Radiation. The intensity and
(1) American National Standards Institute. ANSI/
wavelengths of nonionizing radiant energy produced
ASC Z136.1, Safe Use of Lasers, New York, NY:
depend on many factors, such as the process, welding
American National Standards Institute.
parameters, electrode and base-metal composition,
fluxes, and any coating or plating on the base metal. (2) . ANSI/ASC Z87.1, Practice for Occupational
Some processes such as resistance welding and cold and Educational Eye and Face Protection. New York,
pressure welding ordinarily produce negligible quantities NY: American National Standards Institute.
of radiant energy. However, most arc welding and (3) . ANSI/ASC Z49.1, Safety in Welding, Cutting,
cutting processes (except submerged arc when used and Allied Processes. (published by AWS) Miami, FL:
properly), laser welding and torch welding, cutting, American Welding Society.
brazing, or soldering can produce quantities of non- (4) Hinrichs, J. F. Project committee on radiation-
ionizing radiation such that precautionary measures are summary report. Welding Journal, January, 1978.
necessary. (5) Moss, C. E. Optical radiation transmission levels
Protection from possible harmful effects caused by through transparent welding curtains. Welding Journal,
nonionizing radiant energy from welding include the March 1979.
following measures:
(6) Moss, C. E. and Murray, W. E. Optical radiation
(1) One should not look at welding arcs except
levels produced in gas welding, torch brazing, and
through welding filter plates which meet the require-
oxygen cutting. Welding Journal, September 1979.
ments of ANSI/ASC Z87.1, Practice for Occupational
and Educational Eye and Face Protection, published (7) Marshall, W. J., Sliney, D. H. and others. Optical
by American National Standards Institute. It should be radiation levels produced by air-carbon arc cutting
noted that transparent welding curtains are not intended processes, Welding Journal, March 1980.
as welding filter plates, but rather are intended to (8) National Technical Information Service. Non-
protect a passerby from incidental exposure. ionizing radiation protection special study no. 42-0053-
(2) Exposed skin should be protected with adequate 77, Evaluation of the potential hazards from actinic
gloves and clothing as specified in ANSI/ASC Z49.1, ultraviolet radiation generated by electric welding and
Safety in Welding, Cutting, and Allied Processes, pub- cutting arcs. Springfield, VA: National Technical Infor-
lished by American Welding Society. mation Service. ADA-033768.
(3) Reflections from welding arcs should be avoided, (9) . Non-ionizing radiation protection special
and all personnel should be protected from intense study no. 42-0312-77, Evaluation of the potential retina
reflections. (Note: Paints using pigments of substantially hazards from optical radiation generated by electrical
zinc oxide or titanium dioxide have a lower reflectance welding and cutting arcs. Springfield, VA: National
for ultraviolet radiation.) Technical Information Service, ADA-043023.
147

C067

Uploaded by

Copyright:

Available Formats

C067

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

C067

Uploaded by

Copyright:

Available Formats

SPECIFICATION FOR LOW-ALLOY STEEL

ELECTRODES FOR SHIELDED METAL ARC

(Identical with AWS Specification A5.5-96.)

PART A GENERAL REQUIREMENTS 5. Units of Measure and Rounding-Off

PART B TESTS, PROCEDURES, AND 8. Weld Test Assemblies

7. Retest 8.2 The preparation of each weld test assembly shall

E7010-A1 W17010 0.12 0.60 0.40 0.03 0.03 0.400.65

Chromium-Molybdenum Steel Electrodes

E8016-B2 W52016 0.050.12 0.90 0.60 0.03 0.03 1.001.50 0.400.65

E7015-B2L W52115 0.05 0.90 1.00 0.03 0.03 1.001.50 0.400.65

E9015-B3 W53015 0.050.12 0.90 1.00 0.03 0.03 2.002.50 0.901.20

E8015-B3L W53115 0.05 0.90 1.00 0.03 0.03 2.002.50 0.901.20

E8015-B4L W53415 0.05 0.90 1.00 0.03 0.03 1.752.25 0.400.65

PART C SPECIFICATIONS FOR WELDING RODS,

ELECTRODES, AND FILLER METALS

E8016-C1 W22016 0.12 1.25 0.60 0.03 0.03 2.002.75

E7015-C1L W22115 0.05 1.25 0.50 0.03 0.03 2.002.75

E8016-C2 W23016 0.12 1.25 0.60 0.03 0.03 3.003.75

E8016-C4 W21916 0.10 1.25 0.60 0.03 0.03 1.102.00

E9015-C5L W25018 0.05 0.401.00 0.50 0.03 0.03 6.007.25

Nickel-Molybdenum Steel Electrodes

Manganese-Molybdenum Steel Electrodes

E8018-D1 W18118 0.12 1.001.75 0.80 0.03 0.03 0.90 0.250.45

PART C SPECIFICATIONS FOR WELDING RODS,

ELECTRODES, AND FILLER METALS

E8010-P1 80 550 67 460 19 AW

E9010-G 90 620 77 530 17 AW or PWHT

E11010-G 110 760 97 670 15 AW or PWHT

E12010-G 120 830 107 740 14 AW or PWHT

AWS Classification Average, min.b Single Value, min.b

E7010-P1 20 ftlbf at 20F 15 ftlbf at 20F

E8016-C1 20 ftlbf at 75Fa 15 ftlbf at 75Fa

E7015-C2L 20 ftlbf at 150Fa 15 ftlbf at 150Fa

20 ftlbf at 175Fa 15 ftlbf at 175Fa

sample shall be free of slag and shall be taken from

9.2 The sample described in 9.1 shall be analyzed

9.3 The results of the chemical analysis shall meet

10. Radiographic Test

10.2 The weld shall be radiographed in accordance

10.3 The soundness of the weld metal meets the

FIG. 3 FILLET WELD TEST ASSEMBLY

Thickness Length Size of

FIG. 5 WELDING POSITIONS FOR FILLET WELD TEST ASSEMBLIES

FIG. 6 RADIOGRAPHIC ACCEPTANCE STANDARDS FOR ROUNDED INDICATIONS (GRADE 1)

FIG. 6 RADIOGRAPHIC ACCEPTANCE STANDARDS FOR ROUNDED INDICATIONS (GRADE 2) (CONTD)

TABLE 9 14.4 The apparatus used for moisture testing with

FIG. 7 ALL-WELD-METAL TENSION TEST SPECIMEN DIMENSIONS

FIG. 8 CHARPY V-NOTCH IMPACT TEST SPECIMEN

the combustion tube, and the tube closed. After heating

15. Absorbed Moisture Test

in. mm in. mm in. mm

FIG. 10 ALTERNATE METHODS FOR FACILITATING FRACTURE OF THE FILLET WELD

AWS Classification Electrode Designationa As-Received or Reconditionedb As-Exposedc

FIG. 11 SCHEMATIC OF TRAIN FOR MOISTURE DETERMINATION

All Classifications except

in. mm in. mm in. mm

FIG. 12 ORDER OF ELECTRODE MANDATORY AND OPTIONAL SUPPLEMENTAL DESIGNATORS

AWS Classifications Ambient Air Holding Ovens Drying Conditionsb

EXX13-X 60100F (1638C)