Sony HCD-GT3D PDF

HCD-GT3D
SERVICE MANUAL Russian Model

E Model
Ver. 1.2 2015.08
Australian Model
Model Name Using Similar Mechanism HCD-GPX555

CD/DVD Section CD Mechanism Type CDM90-DVBU204//M
Optical Pick-up Name CMS-S76RFS7G
SPECIFICATIONS
Amplifier section Maximum current FM tuner section Power consumption (at the Power Saving
The following are measured at 1A System mode)
AC 120 V – 240 V, 50/60 Hz Disc/USB section PLL quartz-locked digital synthesizer 0.5 W
Power output (rated) Supported bit rate Antenna (When “BT STBY” is set to “OFF”)
Left/Right Channel: 120 W + 120 W MPEG1 Layer-3: FM lead antenna 6W
(at 2 ohms, 1 kHz, 1% THD) 32 kbps – 320 kbps, VBR Tuning range (When “BT STBY” is set to “ON”)
RMS output power (reference) Sampling frequencies 87.5 MHz – 108.0 MHz (50 kHz step) Dimensions (w/h/d) (Approx.)
Left/Right Channel: 180 W + 180 W MPEG1 Layer-3: BLUETOOTH section DVD Receiver (subwoofer unit):
(per channel at 2 ohms, 1 kHz) 32 kHz/44.1 kHz/48 kHz Communication system 305 mm × 636 mm × 355 mm
Subwoofer: 360 W (at 4 ohms, 100 Hz) Xvid BLUETOOTH Standard version 3.0 Mass (Approx.)
Video codec: Xvid DVD Receiver (subwoofer unit):
Speaker section Output
Bit rate: 4.854 Mbps (MAX) BLUETOOTH Standard Power 14.5 kg
Speaker system
Subwoofer, Sound Pressure Horn Resolution/Frame rate: Class 2
Speaker unit 720 × 480, 30 fps Maximum communication range Design and specifications are subject to
200 mm, cone type 720 × 576, 25 fps Line of sight approx. 10 m 1) change without notice.
Rated impedance Audio codec: MP3 Frequency band
4 ohms MPEG4 2.4 GHz band (2.4000 GHz –
Inputs
File format: MP4 File Format 2.4835 GHz) – Continued on next page –
Video codec: Modulation method
AUDIO IN/PARTY CHAIN IN L/R
MPEG4 Simple Profile FHSS (Freq Hopping Spread Spectrum)
Voltage 2 V, impedance 47 kilohms
(AVC is not compatible.) Compatible BLUETOOTH profiles 2)
OPTICAL IN
Bit rate: 4 Mbps A2DP (Advanced Audio Distribution
Supported audio signal:
Resolution/Frame rate: Profile)
2-channel Linear PCM
720 × 576, 30 fps AVRCP (Audio Video Remote
MIC 1, MIC 2
Audio codec: AAC-LC Control Profile)
Sensitivity 1 mV, impedance 10 kilohms
(HE-AAC is not compatible.) SPP (Serial Port Profile)
(USB) port
DRM: Not compatible Supported codecs
Type A
Disc player section SBC (Sub Band Codec)
Outputs AAC (Advanced Audio Coding)
System
AUDIO OUT/PARTY CHAIN OUT L/R
Compact disc and digital audio and 1)
The actual range will vary depending on
Voltage 2 V, impedance 1 kilohm
video system factors such as obstacles between devices,
VIDEO OUT
Laser Diode Properties magnetic fields around a microwave oven,
Max. output level 1 Vp-p, unbalanced,
Emission Duration: Continuous static electricity, reception sensitivity,
Sync. negative load impedance 75 ohms
Laser Output*: Less than 44.6 μW antenna’s performance, operating system,
USB section * This output is the value software application, etc.
Supported bit rate measurement at a distance of 2)
WMA: BLUETOOTH standard profiles indicate
200 mm from the objective lens
48 kbps – 192 kbps, VBR, CBR the purpose of BLUETOOTH communica-
surface on the Optical Pick-up
AAC: tion between devices.
Block with 7 mm aperture.
48 kbps – 320 kbps, VBR, CBR Frequency response General
Sampling frequencies 20 Hz – 20 kHz Power requirements
WMA: 44.1 kHz Video color system format AC 120 V – 240 V, 50/60 Hz
AAC: 44.1 kHz NTSC and PAL Power consumption
Supported USB device 120 W
DVD RECEIVER
Mass Storage Class
9-890-669-03
2015H81-1 Sony Corporation
© 2015.08 Published by Sony EMCS (Malaysia) PG Tec
HCD-GT3D
Ver. 1.1
License and Trademark Notice SAFETY CHECK-OUT

• is a trademark of DVD Format/Logo Licensing Corporation.
After correcting the original service problem, perform the following
• “DVD+RW”, “DVD-RW”, “DVD+R”, “DVD-R”, “DVD VIDEO”, and
the “CD” logos are trademarks.
safety check before releasing the set to the customer:
• MPEG Layer-3 audio coding technology and patents licensed from Check the antenna terminals, metal trim, “metallized” knobs,
Fraunhofer IIS and Thomson. screws, and all other exposed metal parts for AC leakage. Check
• Windows Media is either a registered trademark or trademark of leakage as described below.
Microsoft Corporation in the United States and/or other countries.
• This product is protected by certain intellectual property rights of
Microsoft Corporation. Use or distribution of such technology outside LEAKAGE TEST
of this product is prohibited without a license from Microsoft or an
authorized Microsoft subsidiary.
The AC leakage from any exposed metal part to earth ground and
• “WALKMAN” and “WALKMAN” logo are registered trademarks of from all exposed metal parts to any exposed metal part having a
Sony Corporation. return to chassis, must not exceed 0.5 mA (500 microamperes).
• This system incorporates Dolby* Digital. Leakage current can be measured by any one of three methods.
* Manufactured under license from Dolby Laboratories. Dolby and
the double-D symbol are trademarks of Dolby Laboratories. 1. A commercial leakage tester, such as the Simpson 229 or RCA
• The BLUETOOTH® word mark and logos are registered trademarks WT-540A. Follow the manufacturers’ instructions to use these
owned by Bluetooth SIG, Inc. and any use of such marks by Sony instruments.
Corporation is under license. Other trademarks and trade names are
those of their respective owners. 2. A battery-operated AC milliammeter. The Data Precision 245
• The N Mark is a trademark or registered trademark of NFC Forum, digital multimeter is suitable for this job.
Inc. in the United States and in other countries.
3. Measuring the voltage drop across a resistor by means of a
• Android™ is a trademark of Google Inc.
VOM or battery-operated AC voltmeter. The “limit” indication
• Google Play™ is a trademark of Google Inc.
is 0.75 V, so analog meters must have an accurate low-voltage
• Apple, the Apple logo, iPhone, and iPod touch are trademarks of
Apple Inc., registered in the U.S. and other countries. App Store is a scale. The Simpson 250 and Sanwa SH-63Trd are examples
service mark of Apple Inc. of a passive VOM that is suitable. Nearly all battery operated
• “Made for iPod” and “Made for iPhone” mean that an electronic
accessory has been designed to connect specifically to iPod or iPhone,
digital multimeters that have a 2V AC range are suitable. (See
respectively, and has been certified by the developer to meet Apple Fig. A)
performance standards. Apple is not responsible for the operation of
this device or its compliance with safety and regulatory standards.
Please note that the use of this accessory with iPod or iPhone may
affect wireless performance. To Exposed Metal
• THIS PRODUCT IS LICENSED UNDER THE MPEG-4 VISUAL Parts on Set
PATENT PORTFOLIO LICENSE FOR THE PERSONAL AND
NON-COMMERCIAL USE OF A CONSUMER FOR
(i) ENCODING VIDEO IN COMPLIANCE WITH THE MPEG-4
VISUAL STANDARD (“MPEG-4 VIDEO”)
AND/OR
(ii) DECODING MPEG-4 VIDEO THAT WAS ENCODED BY
A CONSUMER ENGAGED IN A PERSONAL AND NON-
COMMERCIAL ACTIVITY AND/OR WAS OBTAINED FROM AC
A VIDEO PROVIDER LICENSED TO PROVIDE MPEG-4 0.15 μF 1.5 kΩ voltmeter
VIDEO. (0.75 V)
NO LICENSE IS GRANTED OR SHALL BE IMPLIED FOR ANY
OTHER USE. ADDITIONAL INFORMATION INCLUDING THAT
RELATING TO PROMOTIONAL, INTERNAL AND COMMER-
CIAL USES AND LICENSING MAY BE OBTAINED FROM MPEG
LA, L.L.C.
HTTP://WWW.MPEGLA.COM
• All other trademarks are trademarks of their respective owners.
Earth Ground
• In this manual, ™ and ® marks are not specified.
Fig. A. Using an AC voltmeter to check AC leakage.
• Abbreviation
AR : Argentina model
AUS : Australian model
E4 : African model
EA : Saudi Arabia model
LA9 : Latin-American model
MY : Malaysia model
RU : Russian model
TH : Thai model
SAFETY-RELATED COMPONENT WARNING!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE

WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS
WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS
MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
2
HCD-GT3D
TABLE OF CONTENTS
1. SERVICING NOTES ............................................. 4 6-30. Schematic Diagram - SPLITTER Board - ...................... 58
2. DISASSEMBLY 7. EXPLODED VIEWS

2-1. Disassembly Flow ........................................................... 9 7-1. Side Panel Section .......................................................... 72
2-2. Side (L) Panel, Side (R) Panel ........................................ 10 7-2. Top Panel Section ........................................................... 73
2-3. Top Panel Section ........................................................... 11 7-3. Loading Panel Section .................................................... 74
2-4. OPTICAL Board ............................................................. 12 7-4. MOTHERBOARD Board Section .................................. 75
2-5. Loading Panel Assy ........................................................ 12 7-5. Chassis Section ............................................................... 76
2-6. CDM Section .................................................................. 13 7-6. Front Panel Section ......................................................... 77
2-7. Back Panel ...................................................................... 13 7-7. CDM Section .................................................................. 78
2-8. DAMP Board .................................................................. 14 7-8. CD Mechanism Section
2-9. MOTHERBOARD Board, SPLITTER Board ................ 15 (CDM90-DVBU204//M) ................................................ 79
2-10. Sub Chassis Section ........................................................ 16
2-11. SMPS Board ................................................................... 17 8. ELECTRICAL PARTS LIST .............................. 80
2-12. Chassis ............................................................................ 17
2-13. Front Panel Section ......................................................... 18
2-14. Loudspeaker (20cm)-087-11 ........................................... 19
2-15. Service, Optical Device(7G), Wire (Flat Type) .............. 20
3. TEST MODE ............................................................ 21
4. ELECTRICAL CHECK ......................................... 26
5. TROUBLESHOOTING .......................................... 27
6. DIAGRAMS
6-1. Block Diagram - SERVO/USB/DISPLAY Section - ...... 33
6-2. Block Diagram - AUDIO/VIDEO Section - ................... 34
6-3. Block Diagram - AMP Section - ..................................... 35
6-4. Block Diagram - POWER SUPPLY Section - ................ 36
6-5. Printed Wiring Board - MOTHERBOARD Board - ....... 39
6-6. Schematic Diagram
- MOTHERBOARD Board (1/10) - ............................... 40
- MOTHERBOARD Board (10/10) - ............................. 49
6-16. Printed Wiring Board - DAMP Board - .......................... 50
6-17. Schematic Diagram - DAMP Board (1/2) - .................... 51
6-18. Schematic Diagram - DAMP Board (2/2) - .................... 52
6-19. Printed Wiring Board - BUTTON Board - ..................... 53
6-20. Schematic Diagram - BUTTON Board - ........................ 54
6-21. Printed Wiring Board - LCD Board -.............................. 55
6-22. Schematic Diagram - LCD Board - ................................ 55
6-23. Printed Wiring Board - OPTICAL Board - ..................... 55
6-24. Schematic Diagram - OPTICAL Board -........................ 55
6-25. Printed Wiring Board - SPK_HLED Board -.................. 56
6-26. Schematic Diagram - SPK_HLED Board - .................... 56
6-27. Printed Wiring Board - MIC Board - .............................. 56
6-28. Schematic Diagram - MIC Board - ................................. 57
6-29. Printed Wiring Board - SPLITTER Board - ................... 58
3
HCD-GT3D
Ver. 1.1 SECTION 1
SERVICING NOTES
Notes on chip component replacement MODEL IDENTIFICATION
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be – Rear View – MODEL NUMBER LABEL
damaged by heat.
Flexible Circuit Board Repairing

• Keep the temperature of the soldering iron around 270 °C
during repairing.
• Do not touch the soldering iron on the same conductor of the Destination Code
circuit board (within 3 times). Part No.
• Be careful not to apply force on the conductor when soldering
or unsoldering.
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the
leadfree mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARK

Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40 °C higher
than ordinary solder. Model Part No.
Ordinary soldering irons can be used but the iron tip has to be
AR 4-566-431-0[]
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to LA9 4-567-343-0[]
about 350 °C. TH 4-567-344-0[]
Caution: The printed pattern (copper foil) may peel away if E4 4-567-347-0[]
the heated tip is applied for too long, so be careful!
EA 4-567-349-0[]
• Strong viscosity
Unleaded solder is more viscous (sticky, less prone to flow) MY 4-567-350-0[]
than ordinary solder so use caution not to let solder bridges RU 4-567-352-0[]
occur such as on IC pins, etc. AUS 4-567-353-0[]
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
• Abbreviation
also be added to ordinary solder. AR : Argentina model
CAUTION E4 : African model
Use of controls or adjustments or performance of procedures EA : Saudi Arabia model
other than those specified herein may result in hazardous radiation LA9 : Latin-American model
exposure. MY : Malaysia model
RU : Russian model
TH : Thai model
NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK
OR BASE UNIT • JIG
When disassembling the set, use the following jig (for front
panel removal).
The laser diode in the optical pick-up block may suffer electrostatic
Part No.: J-2501-238-A JIG FOR SPEAKER REMOVAL
break-down because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care. PLAYABLE DISCS
• DVD+R/DVD+RW
NOTES ON LASER DIODE EMISSION CHECK • AUDIO CD
The laser beam on this model is concentrated so as to be focused • CD-R/CD-RW/DVD-R/DVD-RW
on the disc reflective surface by the objective lens in the optical – audio data
pickup block. Therefore, when checking the laser diode emission, – MP3 files that conforms to ISO9660 Level 1/Level 2, or
observe from more than 30 cm away from the objective lens. Joliet (expansion format).
Notes
This appliance is classified as • MP3 (MPEG 1 Audio Layer-3) is a standard format defined
a CLASS 1 LASER product by ISO (International Organization for Standardization) which
under IEC 60825-1:2007. compresses audio data. MP3 files must be in MPEG 1 Audio
This marking is located on Layer-3 format.
the rear exterior. • The system can only play back MP3 files that have a file
extension of “.mp3”.
4
HCD-GT3D
Ver. 1.1
NOTE OF REPLACING THE IC001, IC002, IC101, IC105, NOTE OF REPLACING MOTHERBOARD BOARD OR
IC106, IC301, IC302 AND IC303 ON THE MOTHERBOARD BLUETOOTH MODULE OR RC-S730 (WW) BOARD
BOARD When the MOTHERBOARD board or BLUETOOTH module
IC001, IC002, IC101, IC105, IC106, IC301, IC302 and IC303 or RC-S730 (WW) board are replaced, please execute the below
on the MOTHERBOARD board cannot exchange with single. service mode.
When these parts on the MOTHERBOARD board are damaged,
exchange the entire mounted board.
Pairing this system with a Bluetooth device
NOTE OF REPLACEMENT OF THE MS-476 BOARD 1. Press the [\/1] button to turn the power on.
When the MS-476 board is defective, exchange the entire 2. Place the Bluetooth device within 1 meter (3 feet) from the
LOADING COMPLETE ASSY (T). system.
3. Press BLUETOOTH on the unit to select Bluetooth function.
RELEASING THE DISC TRAY LOCK “BT AUDIO” appears in the display panel.
The disc tray lock function for the antitheft of an demonstration 4. Hold down BLUETOOTH on the unit for 2 seconds or more.
disc in the store is equipped. “PAIRING” flashes in the display panel.
5. Perform the pairing procedure on the Bluetooth device.
Releasing Procedure: 6. Select the model number of the unit on the display of the
1. Press [\/1] button to turn the power on. Bluetooth device.
2. Press [FUNCTION] button and turn the [MULTI CONTROL] For example, select “SONY : MHC-GT3D”. If passkey is
knob to select “DVD/CD” function, then press [ENTER] required on the Bluetooth device, enter “0000”.
button. 7. Perform the Bluetooth connection on the Bluetooth device.
3. Press the [ENTER] button and [VOCAL FADER] button 8. When pairing is completed and the Bluetooth connection is
simultaneously and hold down for around 3 seconds. established, the Bluetooth device name appears in the display
4. The message “UNLOCKED” is displayed and the disc tray is panel.
unlocked. 9. To cancel pairing operation, hold down BLUETOOTH on the
unit for 2 seconds or more until “BT AUDIO” appears in the
Note: When “LOCKED” is displayed, the slot lock is not released by display panel.
turning power on/off with the [\/1] button.
NOTE OF REPLACING THE IC1001 ON THE DAMP Connecting with a smartphone by one touch (NFC)
BOARD AND THE COMPLETE DAMP BOARD
Note: The operation in this mode must use a NFC-compatible smartphone
When IC1001 on the DAMP board and the complete DAMP board (Smartphones with a built-in NFC function [OS: Android 2.3.3 or
are replaced, it is necessary to spread the compound between parts later, excluding Android 3.x])
and heat sink.
1. Press the [\/1] button to turn the power on.
Part No. Description 2. Download and install the app “NFC Easy Connect”.
7-300-009-67 THERMAL COMPOUND (TIG2000) Download the free Android app from Google Play by searching
for “NFC Easy Connect”.
Spread the compound referring to the figure below.
3. Start the app “NFC Easy Connect” on the smartphone.
Make sure that the application screen is displayed.
– DAMP Board (Component Side) –
4. Touch the smartphone to the N-Mark on the system until the
smartphone vibrates.
thermal compound (TIG2000)

Complete the connection by following the instructions
displayed on the smartphone.
5. When pairing is completed and the Bluetooth connection is
IC1001 established, the Bluetooth device name appears in the display
panel.
5
HCD-GT3D
Ver. 1.2
NOTE OF DISASSEMBLE THE PANEL, SIDE

Playing music from a Bluetooth device
To disassemble the PANEL, SIDE, hexagon key is required to
For a Bluetooth device unscrew the SCREW, TAPPING (HEX) (Type A).
2. Press BLUETOOTH on the unit to select Bluetooth function.
“BT AUDIO” appears in the display panel.
3. Establish connection with the Bluetooth device. hexagon key
Press BLUETOOTH on the unit to connect to the last
connected Bluetooth device.
Perform the Bluetooth connection from the Bluetooth device if
the device is not connected.
Once the connection is established, the Bluetooth device name
appears in the display panel.
4. Press N.
Depending on the Bluetooth device,
– you may have to press N twice.
– you may need to start playback of an audio source on the
Bluetooth device. hexagon key
For an NFC-compatible smartphone

Touch the smartphone to the N-Mark on the system to establish
the Bluetooth connection.
Start playback of an audio source on the smartphone. For
details on playback, refer to the operating instructions of your
smartphone.
BOND FIXATION OF ELECTRIC PARTS
When DAMP board is replaced or the following object parts are
To disconnect the Bluetooth device replaced, it is necessary to fix parts to the boards by using a speci-
For a Bluetooth device fied bond without fail.
Press BLUETOOTH on the unit.
“BT AUDIO” appears in the display panel. • Object boards
Complete DAMP board
For an NFC-compatible smartphone
Touch the smartphone to the N-Mark on the system again. • Object parts
Board Ref. No.
To erase all the pairing registration information perform C1126, C1127, C1128, C1129, C1142,
COLD RESET test mode (Refer to page 21). DAMP
L1010, RY001
SCREW TYPE DISCRIMINATION BEFORE DISASSEM-

BLE THE PANEL, SIDE • Use bond
In this set, the screw type which screw between “PANEL, SIDE Part No. Description
and PANEL, TOP” and “PANEL, SIDE and CHASSIS” have been 7-600-020-70 ADHESIVE (SC608Z2) 180ML
changed in the midway of production.
Repair after distinguishing the screw type referring to the • Parts position
following. Complete DAMP board (page 6)
Type A or Type B
DAMP board
– DAMP Board (Component Side) –
RY001
C1142
C1127 C1128
Type A or Type B
C1126 C1129
L1010
Type Screw P/N Screw Shape
A 4-546-397-01
B 4-162-271-01
The portion which applies bond:
6
HCD-GT3D
Ver. 1.2
HOW TO OPEN THE TRAY WHEN POWER SWITCH TURN OFF

Note 1: After the side panel and top panel are removed, this work is done.
Note 2: Please prepare the thin wire (clip etc. processed to the length of 8 cm or more).
1 Remove the side (L) panel, side (R) panel, top panel section.
(Illustration of disassembly is omitted.)
hole
– Left view –
3
Insert the clip etc. processed to the
length of 8 cm or more in the hole CD/DVD mechanism deck
on the side of the chassis and push.
8 cm or more 2 Insert the clip etc.
tray
Note: Push after it inserts it
in this hole well.
– Top view –
NOTE OF REPLACING THE VOLUME KNOB ASSY OR MIC KNOB

When VOLUME knob assy or MIC knob is replaced, it is necessary to apply lubricant on the knob.
Part No. Description

7-651-000-63 Lubricant (SFL-7A)1KG
Apply the lubricant referring to the figure below.
– VOLUME KNOB ASSY – – MIC KNOB ASSY –
Lubricant (SFL-7A)1KG
7
HCD-GT3D
CAPACITOR DISCHARGE FOR ELECTRIC SHOCK PREVENTION
SMPS Board (Conductor side view)

In checking the SMPS board, make 3 capacitors discharge of C914, C1003 and C1006 for eletrical shock prevention.
800 :/5 W
800 :/5 W
C1003
800 :/5 W
C914
C1006
8
HCD-GT3D
SECTION 2
DISASSEMBLY
Note: Disassemble the unit in the order as shown below.
2-1. DISASSEMBLY FLOW
SET
2-2. SIDE (L) PANEL, SIDE (R) PANEL

(Page 10)
2-3. TOP PANEL SECTION

(Page 11)
2-4. OPTICAL BOARD

(Page 12)
2-5. LOADING PANEL ASSY

(Page 12)
2-6. CDM SECTION

(Page 13)
2-7. BACK PANEL 2-15. SERVICE, OPTICAL DEVICE(7G), WIRE (FLAT TYPE)
(Page 13) (Page 20)
2-8. DAMP BOARD

(Page 14)
2-9. MOTHERBOARD BOARD,

SPLITTER BOARD
(Page 15)
2-10. SUB CHASSIS SECTION

(Page 16)
2-11. SMPS BOARD

(Page 17)
2-12. CHASSIS
(Page 17)
2-13. FRONT PANEL SECTION

(Page 18)
2-14. LOUDSPEAKER (20CM)-087-11

(Page 19)
9
HCD-GT3D
Ver. 1.2
Note: Follow the disassembly procedure in the numerical order given.
2-2. SIDE (L) PANEL, SIDE (R) PANEL
1 two screws 3 three claws

(TAPPING (HEX)
(Type A) or TAPPING
(Type B))
2 three screws (+BVTP 3 × 8)
5 panel, side (L)

2 three screws (+BVTP 3 × 8)
4 Remove the panel, side (L)

3 three claws
in the direction of the arrow.
5 panel, side (R)
1 two screws (TAPPING (HEX)

(Type A) or TAPPING (Type B))
4 Remove the panel, side (R)
Note 1: The screw type which screw between “PANEL, SIDE and PANEL,
TOP” and “PANEL, SIDE and CHASSIS” for this unit have been
changed in the midway of production. About the screw type dis-
crimination, refer to “SCREW TYPE DISCRIMINATION BEFORE
DISASSEMBLE THE PANEL, SIDE” on servicing notes (page 6).
10
HCD-GT3D
Ver. 1.2
3 two screws (+BVTP 3 × 8) 1 three screws (+BVTP 3 × 8)
D A
4 one screw (+BVTP 3 × 8)
qs top panel section
F 8 Remove the wires from pin, lead.

C
B 4 one screw (+BVTP 3 × 8)
G
E :LUHVHWWLQJ
6 three claws
9 wire (flat type) (11 core) (CN3402) MIC board

0 CN451 (8P)
pin, lead
7 Remove the top panel section A
in the direction of the arrow. MOTHERBOARD
qa CN3200 (4P) front side board
5 one screw (+BVTP 3 × 8) D
F
C
B
G
E
11
HCD-GT3D
Ver. 1.2
2-4. OPTICAL BOARD
4 one screw (+BVTP 3 × 8) 1 Remove the wire from pin, lead.
:LUHVHWWLQJ
5 OPTICAL board A OPTICAL board
pin, lead
2 CN602 (3P)
3 one screw front side
(+BVTP 3 × 8)
A
MOTHERBOARD board
2-5. LOADING PANEL ASSY
4 panel, loading assy

3 three claws
hole
– Left view –
Insert the clip etc. processed to the

length of 8 cm or more in the hole CD/DVD mechanism deck
on the side of the chassis and push.
2 Draw out the tray.
8 cm or more 1 Insert the clip etc.
tray
Note: Push after it inserts it
in this hole well.
– Top view –
12
HCD-GT3D
Ver. 1.2
2-6. CDM SECTION
1 two screws (+BVTP 3 × 8)

A
8 CDM section
7 wire (flat type) (24 core) (CN302)

6 wire (flat type) (5 core) (CN303) 5 CN401 (6P)
3 two claws
4 Remove the CDM section
2-7. BACK PANEL

3 four screws (+BVTP 3 × 8)
4 five screws (+BVTP 3 × 8)
5 panel, back
13
HCD-GT3D
Ver. 1.2
2-8. DAMP BOARD
:LUHVHWWLQJ
DAMP board
8 heatsink
chassis, sub Note: When you install the heatsink, spread the compound
rear side referring to “NOTE OF REPLACING THE IC1001
ON THE DAMP BOARD AND THE COMPLETE
DAMP BOARD” on servicing notes (page 5).
holder, wire
6 four screws (+BVTP 3 × 8)
1 Remove the wires

from holder, wire. 9 DAMP board
3 CN1005 (8P)
2 CN1007 (2P)
4 CN1004 (2P)
– Rear view –
14
HCD-GT3D
Ver. 1.2
2-9. MOTHERBOARD BOARD, SPLITTER BOARD
B 5 wire (flat type) (25 core) (CN118)

qa SPLITTER board
7 five screws (+BVTP 3 × 8)
A
8 MOTHERBOARD board

A
B
3 CN001 (9P)
1 Remove the wires from holder, wire.
2 CN517 (4P)
– Rear view –
:LUHVHWWLQJ
front side MOTHERBOARD

board
chassis, sub
holder, wire
15
HCD-GT3D
Ver. 1.2
2-10. SUB CHASSIS SECTION
:LUHVHWWLQJ
clamp front side
fan, DC
2 three screws (+BV3 (3-CR))
3 clamp bracket, fan

1 Remove the wire from clamp.
4 four screws (+BV3 (3-CR)) chassis, sub
7 sub chassis section
6 Draw out the wires from chassis, sub.

B A
5 Remove the sub chassis section :LUHVHWWLQJ

in the direction of the arrow. chassis, sub
front side
B
A chassis
16
HCD-GT3D
Ver. 1.2
2-11. SMPS BOARD
2 AC inlet
3 nine screws (+PWH 3 × 8 (SUMITITE))
1 CN901 (2P)
4 SMPS board
2-12. CHASSIS
2 seven step screws (M4)
A
3 one claw
5 chassis
3 one claw
4 nine damper chassis
17
HCD-GT3D
Ver. 1.2
1 one screw ((4 × 13) (TR-184A))
2 Insert the jig into a space and slowly

remove the front panel section.
Note : When using a jig, please work
so as not to injure front panel
section and speaker cabinet.
3 All bosses are removed while moving

jig in the direction of the arrow, and
front panel section is removed.
total fourteen bosses

2 Insert the jig into a space and slowly
remove the front panel section.
Note : When using a jig, please work
so as not to injure front panel
section and speaker cabinet.
3 All bosses are removed while moving

jig in the direction of the arrow, and
4 Remove the front panel section front panel section is removed.
5 front panel section
18
HCD-GT3D
2-14. LOUDSPEAKER (20CM)-087-11
,QVWDOODWLRQGLUHFWLRQIRUWKHORXGVSHDNHUFP
terminal position loudspeaker (20cm)-087-11
3 Push the protrusion,

and remove the terminal
(wide side) [grey]. protrusion
:LUHVHWWLQJ
terminal (wide side)

[grey].
front side
front side
terminal (narrow side)

3 Push the protrusion,
[black/grey].
and remove the terminal
(narrow side) [black/grey].
2 Remove the
loudspeaker (20cm)-087-11
terminal
(wide side)
4 loudspeaker (20cm)-087-11
[grey]
terminal
(narrow side)
[black/grey]
1 four screws ((1) (4 × 20), +BV TAPPING)
19
HCD-GT3D
Ver. 1.2
2-15. SERVICE, OPTICAL DEVICE(7G), WIRE (FLAT TYPE)

2 chuck holder assy (T)
1 three claws
1 three claws
7 four insulator screws

qa insulator
qh holder, FFC
qs service, optical device(7G)
qa insulator
9
8 qj wire (flat type) (24 core)
6 belt qg
qd base, lo assy
3 Insert the clip etc.
0 connector loading assy (T)
– Bottom view –
5 tray
4 qf wire(flat type) (5 core)
,QVWDOODWLRQRIZLUHIODWW\SHFRUHDQGZLUHIODWW\SHFRUH

Note: This illustration sees the loading assy (T) from bottom side.
5 two claws 5 three claws
1 wire (flat type) (24 core)
loading assy (T)
6 holder, FFC
3 Through the hole

4
terminal face
2 Through the hole
Under the guide

(Fold area)
Under the guide
20
HCD-GT3D
SECTION 3
TEST MODE
[PANEL TEST MODE] [COLD RESET]
This mode is used to check the fluorescent indicator tube, LEDs, The cold reset clears all data including preset data stored in the
keys, [VOLUME/DJ CONTROL] jog, model, destination and data flash to initial conditions included history mode data. Execute
software version. this mode when returning the set to the customer.
Procedure: Procedure:
1. Press [] button and [S3 TUNING – .] button simultaneously 1. Press [\/1] button to turn on the system.
and hold 3 seconds. 2. Press [] button and [S4 TUNING + >] button
2. All LEDs and segments in fluorescent indicator tube are simultaneously for 3 seconds.
lighted up. 3. “COLD RST” appears on the fluorescent indicator tube.
3. When you want to enter to the software version display mode, After that, the fluorescent indicator tube will display “SONY
press [S2 +] button. DEMO”. The set will automatically Power ON and Power
The model information appears on the fluorescent indicator OFF again, and the system is reset.
tube.
Press [S2 +] button again to view the destination information. [DISC TRAY LOCK MODE]
4. During the destination information display, press [S2 +] This mode let you lock the disc tray. When this mode is activated,
button. Each time [S2 +] button is pressed, the fluorescent the disc tray will not open when [Z] button is pressed. The mes-
indicator tube shows the version of each category software sage “LOCKED” will be displayed on the fluorescent indicator
in the following sequence: SC, MTK, OPU, UI, PF, SUB, tube. This mode only applied when there is disc on the tray.
SYS, CD, CMA, CMB, ST, TA, TM and return back to model Procedure:
information display. 1. Press [\/1] button to turn on the system.
5. When [] button is pressed while the version numbers are 2. Press [FUNCTION] button and turn the [MULTI CONTROL]
being displayed except model and destination, the date of the knob to select “DVD/CD” function, then press [ENTER]
software creation appears. When [] button is pressed again, button.
the display returns to the software version display. 3. Press [ENTER] button and [VOCAL FADER] button
6. When [ENTER] button is pressed after all LEDs and segments simultaneously and hold down until “LOCKED” or
in fluorescent indicator tube light up, alternate segments in “UNLOCKED” displayed on the fluorescent indicator tube
fluorescent indicator tube and LEDs would light up, all Party (around 3 seconds).
Light LEDs would light up in red color. If you press [ENTER]
button again, another half of alternate segments in fluorescent Bluetooth PAIRING HISTORY CLEAR
indicator tube and LEDs would light up, all Party Light LEDs It can clear the Bluetooth pairing history.
would light up in green color. Pressing [ENTER] button Procedure:
again would cause all segments in fluorescent indicator tube 1. Press [\/1] button to turn on the system.
and LEDs light up, all Party Light LEDs would light up in 2. Press [-PAIRING BLUETOOTH] button to turn the Bluetooth
blue color. Pressing [ENTER] button again would turn off all function.
segments in fluorescent indicator tube and all LEDs including 3. Press two buttons of [ENTER] and [S1 –] simultaneously
Party Light LEDs. for 3 seconds.
7. Press [S1 –] button, the key check mode is activated. 4. The message “BT HIST” → “CLEAR” is displayed on the
8. In the key check mode, the fluorescent indicator tube displays fluorescent indicator tube, and the pairing history of Bluetooth
“K0 V0E0”. is cleared.
Each time a button is pressed, “K” value increases. However,
once a button has been pressed, it is no longer taken into
account. After all the buttons have been pressed, "K" value will
toggle between "OK" and "K24".
“V” value increases in the manner of 0, 1, 2, 3 ... if [VOLUME/
DJ CONTROL] knob is turned clockwise, or it decreases in the
manner of 0, 9, 8, 7 ... if [VOLUME/DJ CONTROL] knob is
turned counterclockwise.
“E” value increases in the manner of 0, 1, 2, 3 ... if [MULTI
CONTROL] knob is turned clockwise, or it decreases in the
manner of 0, 9, 8, 7 ... if [MULTI CONTROL] knob is turned
counterclockwise.
9. To release from this mode, press the buttons in the same
manner as step 1, or disconnect the power cord.
[USER RESET]
The user reset clears all data including preset data stored in the data
flash to initial conditions exclude history mode data.
Procedure:
1. Press [\/1] button to turn on the system.
2. Press [ENTER] button and [S4 TUNING + >] button simul-
taneously for 3 seconds.
3. “RESET” appears on the fluorescent indicator tube. After that,
the fluorescent indicator tube becomes blank for a while, and
the system goes to demo mode.
21
HCD-GT3D
[HISTORY MODE]
This mode is used to check important data stored in the system when PROTECTOR happened.
Procedure:
1. During demo mode, press [] button and [S2 +] button for 5 seconds to mode into history mode.
2. Press the [S4 TUNING + >] button or [S3 TUNING – .] button to check history data stored.
Display on fluorescent indicator tube Description

P C O U N T ※ ※ No. of time protector happened (0 ~ 99)
P T ※ ※ ※ ※ Refer to protect type description
Single Power On Time until protector happened (0~99999 hours,
1 *h *h *h *h *h *m *m
0~99 minutes)
Total Power On Time [ no consider protector happened ]
2 *h *h *h *h *h *m *m
(0~99999 hours, 0~99 minutes)
F ※ ※ ※ ※ ※ ※ Input Function during protector happened
V O L ※ ※ ※ Volume setting (MIN / 1 - 50 / MAX)
S W ※ Subwoofer setting (0 ~ 4)
B A S S ※ ※ ※ MEGA BASS setting (OFF / ON)
To release from History Mode.

To release from this mode, press [\/1] button.
Protect Type Description:
Error Code Description

01 The over current condition to MOSFET occurs by defect of MOSFET or defect of PS output line.
or
Unusual heat up of MOSFET by improper assembly of heat sink, destruction of MOSFET etc.
02 Defect of thermistor IC or charging circuit used by SPM (Sound Pressure Management) system.
03 Defect of power supply circuit to AMP. There is possibility of unusual power supply of any of the AMP IC or Pre-
amplifier.
04 DC appears in SP terminal by defect of AMP IC and MOSFET.
06 Defect of DC FAN and DC FAN driver circuit.
If speaker does not have output even if the set status is not in PROTECT mode, the following defect might be possible:
Defects Possible cause

RESET defect Reset signal status from micom is not ‘H’.
22
HCD-GT3D
Ver. 1.1
[DVD COLOR SYSTEM MODE] 6. To release from this mode, press [\/1] button to turn off the
This mode let you change the color system of the video output system.
from PAL to NTSC or vice-versa.
Procedure: • Execute IOP Measurement
1. Press [\/1] button to turn on the system. In order to execute IOP measurement, the following standard
2. Press [FUNCTION] button and turn the [MULTI CONTROL] procedures must be followed.
knob to select “DVD/CD” function, then press [ENTER]
button. 1. From the Top Menu of Remocon Diagnosis Menu, select
3. Press [ENTER] button and [MIC ECHO] button “2. Drive Manual Operation” by pressing the [2] button on
simultaneously and hold for 3 seconds. the remote commander. The following screen appears on the
4. The message “PAL” or “NTSC” appears on the fluorescent onscreen display.
indicator tube.
Drive Manual Operation
• To release from DVD Color System Mode
1. Once the color system has been selected, the mode is fixed 1. Servo Control
there after. If you wish to change the mode again, perform the 2. Track/Layer Jump
above item 2 again. 3. Manual Adjustment
4. Tray Aging Mode
5. MIRR time Adjust
[DVD SERVICE MODE]
0. Return to Top Menu
This mode let you make diagnosis and adjustment easily by using
the remote commander and the TV. The instructions, diagnostic
2. Select “3. Manual Adjustment” by pressing the [3] button on
results, etc. are given on the on-screen display.
the remote commander. The following screen appears on the
• TEST DISC LIST on-screen display.
Be sure to use the DVD disc that matches the signal standards
Manual Adjust
of your region.
• CD 1. Track Balance Adjust:
YEDS-18 (Part No.: 3-702-101-01) 2. Track Gain Adjust:
PATD-012 (Part No.: 4-225-203-01) 3. Focus Balance Adjust:
HLX-A1 (Part No.: J-2501-307-A) 4. Focus Gain Adjust:
• DVD SL (Single Layer) 5. Eq Boost Adjust:
NTSC : HLX-503 (Part No.: J-6090-069-A) 6. Iop:
HLX-504 (Part No.: J-6090-088-A) 7. TRV. Level:
HLX-513 (Part No.: J-2501-305-A) 8. S curve (FE) Level:
PAL : HLX-506 (Part No.: J-6090-077-A) 9. RFL (PI) Level:
0. MIRR Time:
• DVD DL (Double Layer)
NTSC : HLX-501 (Part No.: J-6090-071-A) O o Change Value
HLX-505 (Part No.: J-6090-089-A) RETURN Return to previous menu
HLX-514 (Part No.: J-2501-306-A)
PAL : HLX-507 (Part No.: J-6090-078-A)
3. Select “6. Iop:” by pressing the [6] button on the remote
commander.
• Procedure to enter to DVD Service Mode:
4. Wait until a hexadecimal number appears in the on-screen
1. Press [\/1] button to turn on the system.
2. Press [FUNCTION] button and turn the [MULTI CONTROL] display as below:
knob to select “DVD/CD” function, then press [ENTER]
Manual Adjust
button.
3. Press [SOUND FIELD] button and [VOCAL FADER] button 1. Track Balance Adjust:
simultaneously and hold 3 seconds. 2. Track Gain Adjust:
4. The message “SERVICE IN” appears on the fluorescent 3. Focus Balance Adjust:
indicator tube. 4. Focus Gain Adjust:
The display of the “Model Name” of the “Remocon Diagnosis 5. Eq Boost Adjust:
Menu” change with the model and the destination appears on 6. Iop. ED
screen display. Refer to below on the model name. 7. TRV. Level:
MHC-GT3D: GV2 8. S curve (FE) Level:
9. RFL (PI) Level:
Remocon Diagnosis Menu 0. MIRR Time:
0. External Chip Check O o Change Value

1. Servo Parameter Check RETURN Return to previous menu
2. Drive Manual Operation
3. Emergency History 5. Convert data from hexadecimal to decimal by using
4. Version Information conversion table.
*1 6. Please find the label on the rear of the BU (Base Unit).
Model Name : MHC-GT3D_ XX
The default IOP value is written in the label.
IF-con : Ver. XX.XX (XXXX)
Syscon : Ver. X.XXX
7. Subtract between these two values.
8. If the remainder is smaller than 93 (decimal), then it is OK.
*1: Changes depending on destination However if the value is higher than 93, then the BU is defective
5. To execute each function, press its number by using numeric and need to be change.
button on the remote commander. 9. Press [RETURN] button on the remote commander to return
to previous menu.
23
HCD-GT3D
Ver. 1.1
10. Press the [0] button on the remote commander to return to the • Parameter of error code
Top Menu of Remocon Diagnosis Menu. This is the detail of error code.
11. Press [\/1] button to turn off the system.
Example of Error code
• Check Emergency History
To check the emergency history, please follow the following 1. 01 05 04 04 00 92 46 00
procedure. 00 00 00 00 00 00 23 45
1. From the Top Menu of Remocon Diagnosis Menu, select • Time of error code
“3. Emergency History” by pressing the [3] button on the This is the laser time when an error occurred.
remote commander. The following screen appears on the on-
screen display. Example of Error code
Emg. History Check 1. 01 05 04 04 00 92 46 00

00 00 00 00 00 00 23 45
Laser Hours CD 999h 59min
DVD 999h 59min
1. 01 05 04 04 00 92 46 00 To clear the Laser Hours

00 00 00 00 00 00 23 45 Press the [ DISPLAY] button and then press the [CLEAR]
2. 02 02 01 01 00 A9 4B 00 button. The data for both CD and DVD data are reset.
00 00 00 00 00 00 23 45
Emg. History Check
Next Next Page Prev Prev Page
O Return to Top Menu
DVD 0h 0min
(Displayed values in the above figure are example)
2. You can check the total time when the laser is turned on 1. 01 05 04 04 00 92 46 00
during playback of DVD and CD from the above menu. The 00 00 00 00 00 00 23 45
2. 02 02 01 01 00 A9 4B 00
maximum time, which can be displayed are 999h 59min.
00 00 00 00 00 00 23 45
3. You can check the error code of latest 10 emergency history
from the above menu. To view the previous or next page of Next Next Page Prev Prev Page
emergency history, press the [.] button or [>] button O Return to Top Menu
on the remote commander. The error code consists of “Error
Code”, “Parameter of error code” and “Time of error code”.
To clear the Emergency History
• Error Code Press the [DVD TOP MENU] button and then press the [CLEAR]
button.
Example of Error code The error code for all emergency history would be reset.
1. 01 05 04 04 00 92 46 00 Emg. History Check

00 00 00 00 00 00 23 45
DVD 999h 59min
The meaning of error code is as below:
01: Communication error (No reply from syscon) 1. 00 00 00 00 00 00 00 00
02: Syscon hung up 00 00 00 00 00 00 00 00
03: Power OFF request when syscon hung up 2. 00 00 00 00 00 00 00 00
19: Thermal shutdown 00 00 00 00 00 00 00 00
24: MoveSledHome error
Next Next Page Prev Prev Page
25: Mechanical move error (5 Changer) O Return to Top Menu
26: Mechanical move stack error
30: DC motor adjustment error
31: DPD offset adjustment error
To clear the Initialize Setup Data
32: TE balance adjustment error
Press the [DVD/TUNER MENU] button and then press the
33: TE sensor adjustment error
[CLEAR] button on the remote commander.
34: TE loop gain adjustment error
35: FE loop gain adjustment error
Emg. History Check
36: Bad jitter after adjustment
40: Focus NG Laser Hours CD 999h 59min
42: Focus layer jump NG DVD 999h 59min
51: Spindle stop error
52: Open kick spindle error Initialize setup data...
60: Focus on error
61: Seek fail error
62: Read Q data/ID error
70: Lead in data read fail Next Next Page Prev Prev Page
71: TOC read time out (CD) O Return to Top Menu
80: Can’t buffering
81: Unknown media type
24
HCD-GT3D
Ver. 1.1
To return to the Top Menu of Remocon Diagnosis Menu

Press the [0] button on the remote commander.
• Check Version Information

To check the version information, please follow the following
procedure.
1. From the Top Menu of Remocon Diagnosis Menu, select “4.

Version information” by pressing the [4] button on the remote
commander. The following screen appears on the on-screen
display.
Version information
Firm (Main) : Ver. xxxxx

Firm (Sub) : xxxxx
RISC : xxxxx
8032 : xxxxx
Audio DSP : xxxxx
Servo DSP : xxxxx
O Return to Top Menu
To return to the Top Menu of Remocon Diagnosis Menu, press

the [0] button on the remote commander.
25
HCD-GT3D
SECTION 4
ELECTRICAL CHECK
TUNER SECTION 0 dB = 1 μV FOCUS BIAS CHECK
oscilloscope
FM AUTO STOP CHECK (DC range)
signal MOTHERBOARD board

generator
CN302 pin 17 (RF) +
CN302 pin 1 (GND) –
set
+ Procedure:
75 1. Connect the oscilloscope to CN302 pin 17 (RF) and CN302
– pin 1 (GND) on the MOTHERBOARD board.
2. Press the [?/1] button to turn the power on, and press the
[FUNCTION] button to select CD function.
3. Set the test disc (CD: YEDS-18) on the tray and press [B]
button to playback.
Procedure: 4. Confirm that oscilloscope waveform is as shown in the figure
1. Turn the power on. below (eye pattern).
2. Input the following signal from Signal Generator to FM A good eye pattern means that the diamond shape (◊) in the
antenna input directly. center of the waveform can be clearly distinguished.
VOLT/DIV: 200 mV
Carrier frequency : A = 87.5 MHz, B = 98 MHz, C = 108 MHz TIME/DIV: 500 ns
Deviation : 75 kHz
Modulation : 1 kHz
ANT input : 35 dBu (EMF) level:
1.1 ± 0.25 Vp-p (DVDSL)
Note: Please use 75 ohm “coaxial cable” to connect SG and the 1.0 ± 0.25 Vp-p (CD)
set. You cannot use video cable for checking.
Please use SG whose output impedance is 75 ohm.
3. Set to FM tuner function and scan the input FM signal with

automatic scanning. Checking Location:
4. Confirm that input Frequency of A, B and C detected and
– MOTHERBOARD Board (Component Side) –
automatic scanning stops.
The stop of automatic scanning means “The station signal is

received in good condition”.
CD/DVD SECTION
[TEST DISC LIST]

Use the following test disc on test mode.
• CD: YEDS-18 (PART No. 3-702-101-01)
or
PATD-012 (PART No. 4-225-203-01) pin 1 (GND) pin 17 (RF)
or
CN302
HLX-A1 (PART No. J-2501-307-A)
• DVD (SL)
NTSC HLX-503 (PART No. J-6090-069-A)
or
HLX-504 (PART No. J-6090-088-A)
or
HLX-513 (PART No. J-2501-305-A)
PAL HLX-506 (PART No. J-6090-077-A)
• DVD (DL)
NTSC HLX-501 (PART No. J-6090-071-A)
or
HLX-505 (PART No. J-6090-089-A)
or
HLX-514 (PART No. J-2501-306-A)
PAL HLX-507 (PART No. J-6090-078-A)
Note: When the BASE UNIT is replaced, perform the Execute
IOP measurement
(Refer to page 24).
26
SMPS Board Diagnosis Flow
(1)
AC IN
(2)
(5) The Power Control signal to SMPS Board is checked.

(6)
Is following power voltage OK? Checks whether the state of a Cable and Outlet are normal.
No
If there are no problems, checks circumference circuit for
Main on Standby Demo mode Power On Main on Output of Main mount side.
CN2005: pin9 Low (0V) Low (0V) Hi (3.3V)
Yes
(4)
(3)
The Output from SMPS Board is checked.

Is following power voltage up to standard?
No
Replaces SMPS Board if it is not up to standard.
Standby Demo mode Power On
CN2005 pin1,4,5 13.5V±0.5V 13.5V±0.5V 13.5V±0.5V
CN4 pin5 0V 0V 50V±5%
(1) AC input Yes

SECTION 5
(2) Fuse
(3) Sub Power transformer END
(4) CN2005 Connector
TROUBLESHOOTING
pin1: 13.5V
pin3: AGND
pin4-5: 13.5V
pin6-7: M/DGND
pin8: AC-DET
pin9: MAIN-ON
(5) MAIN Power transformer
(6) CN4 Connector
pin1-5: V1 (50V)
pin6-9: V1_GND
27
HCD-GT3D
Optical Block Diagnosis Flow (1/2)
28
REMOVE SIDE PANEL
HCD-GT3D
REMOVE TOP PANEL

TURN ON
TRAY IN
No Checks IC303 circumference circuit for +1.2V.

Does Optical pickup move to inner circumference? No Checks CL335 for +3.3V and +1.2V REG IC303.
Checks IC002 (JL040) circumference circuit for
(Visual check) Does it output the power voltage of 3.3V and 1.2V?
+3.3V.
Yes Yes
Checks CN401 SL+/SL- signal. No Checks circumference circuit for SL+/SL- of IC401.
Does it output the signal? Checks circumference circuit of IC301 FMO Signal.
Yes
The Sled motor has a problem.
Replaces BU.
Does Spindle motor rotate? No Checks CN401 SP+/SP- signal. No Checks circumference circuit for SP+/SP of IC401.
(Visual check) Does it output the signal? Checks circumference circuit of IC301 DMO Signal.
Yes Yes
The Spindle motor has a problem.
Replaces BU.
Does Optical pickup do focus search? No Checks CN302 FCS+/FCS- signal. No Checks circumference circuit for FCS+/FCS- of IC401.
(Visual check) Does it output the signal? Checks circumference circuit of IC301 FOO Signal.
Yes Yes
The Optical pickup has a problem.
Replaces BU.
A
Optical Block Diagnosis Flow (2/2)
Does laser diode become luminous? No Checks JL306 (LD780) signal. No Checks circumference circuit of Q402.
(Visual check) Does it output 2V when laser become luminous? Checks circumference circuit of IC301 LD01.
Yes Yes
Replaces BU.
DISC IN
Yes
Is output level of RF signal (JL317) up to standard? No If it is not up to standard,

RF Level = 1.05 ±0.45 Vpp Lens cleaning is performed.
Test disc (CD: YEDS-18, DVD: HLX-503 (NTSC) or HLX-504 (PAL))
Yes
Yes
Is output level of RF signal (JL317) up to standard?
No
RF Level = 1.05 ±0.45 Vpp Replaces BU if it is not up to standard.
Test disc (CD: YEDS-18, DVD: HLX-503 (NTSC) or HLX-504 (PAL))
Yes
Is there no problem with Long term Aging Test (60min)?
Confirms that there is no sound skip. No
Yes

Replaces BU.
END
29
HCD-GT3D
DAMP Mount Diagnosis Flow
30
HCD-GT3D
PLAY MUSIC
Yes
No No
Is there audio output from DAMP Board? Check CN1005 (pin1 refer to pin9). Reinsert the wire and check again. If it is OK,
Is the voltage = 50V? check the SMPS Board position.
Yes
Yes
Yes Check speaker output CN1007 (for subwoofer), TB001 (for FR, FL).
Is the power voltage = 25V?
END No
Yes Check IC1003 (pin1).

Is the power voltage = 12V?
No
Check CN1001 (pin1). No Reinsert FFC and check again. If it is OK, check
Is the voltage = 13V (MAIN ON) ?
MOTHERBOARD Board position.
Yes
Yes Check CN1001 (pin7). No

Is the voltage = 3.3V (AMP-RESET)?
MOSFET Confirmation for DAMP Mount
CL1054
CL1049 CL1048 CL1051

CL1062 CL1050 CL1061
CL1046 CL1047
CL1052
CL1053
Tester Tester Tester Tester
CL1002
CL1032
CL1059
CL1031
Tester Tester Tester Tester
CL1005
CL1023
CL1038
CL1006
CL1007 CL1008
CL1009
CL1004 CL1013 CL1014
CL1017
CL1012 CL1010
CL1003
CL1039 CL1015
CL1001
CL1060 CL1019 CL1063
CL1018 CL1011 CL1016
<Note>
Please check each channel’s resistance value for the Coil’s terminal and Capacitor’s + and – terminal.
These terminal is equal to resistance value for POWER AUDIO DRIVER terminal.
31
Ver. 1.1
HCD-GT3D
HCD-GT3D
SECTION 6
DIAGRAMS
• Circuit Boards Location
DAMP board
BUTTON board MIC board
OPTICAL board
RC-S730 (WW)
MS-476 board MOTHERBOARD board
SMPS board
LCD board
BLUETOOTH MODULE
SPLITTER board
SPK_HLED board
32
HCD-GT3D
6-1. BLOCK DIAGRAM - SERVO/USB/DISPLAY Section -
CD RF AMP FOCUS/TRACKING ERROR AMP,

CD SYSTEM PROCESSOR,
DIGITAL SERVO PROCESSOR SYSTEM CONTROLLER
SERVICE, IC301 SD-RAM IC101 LED DRIVER
OPTICAL DEVICE (7G) (1/2) IC306 (1/4) IC502
BLUE HLED
RF 123 RFIP RA0 89 23 A0 RGB-PWM-CLK 118 21 PWMCLK /OUT0 5
D4001
NC 124 OPDIST RA1 90 24 A1 RGB-TRANS-LED-SPK/SD_WP_0 112 4 TRANS /OUT1 6
VOD/C 127 RF_A RA2 91 25 A2 RGB-SOUT 48 2 SIN /OUT2 7
VOB/B 128 RF_B RA3 92 26 A3 RGB-SCLK 137 3 SCK /OUT3 8
VOA/A 1 RF_C RA4 79 29 A4
VOD/D 2 RF_D RA5 78 30 A5 GREEN HLED
RA0 ~ RA11 REMOTE CONTROL /OUT4 9
VOF/F+H 3 RF_E RA6 77 31 A6 SIGNAL RECEIVER D4002
/OUT5 10
VOE/E+G 4 RF_F RA7 76 32 A7 IC3000
/OUT6 11
RA8 75 33 A8
/OUT7 12
RA9 74 34 A9 SIRCS 135 1 VO
VR (780) 19 CD_VR RA10 88 22 A10/AP RED HLED
VR (650) 20 DVD_VR RA11 73 /OUT8 13
35 A11 D4000
/OUT9 14
VC 10 V20 2
BA0 85 20 BA0 EN3100 /OUT10 15
PD 13 MDI1 JOG+ 44
BA1 86 21 BA1 MULTI /OUT11 16
MSW 23 MSW CONTROL
2 JOG- 49 BASS BAZUCA LED
DQM0 61 15 LDQM /OUT14 19
D3100
DQM1 70 39 UDQM
AUTOMATIC POWER
LD (780) CONTROL (FOR CD) 14 LDO1 EN3101
RCLK 72 38 CLK
Q402 4 VOLUME/
RWE# 80 16 WE MASTER-VOLUME 83
DJ CONTROL BT LED
CAS# 82 17 CAS /OUT15 20
D3105
RAS# 83 18 RAS
AUTOMATIC POWER
LD (650) CONTROL (FOR DVD) 15 LDO2
Q401 RD0 52 2 DQ0
RD1 53 4 DQ1 LED DRIVER BACKLIGHT LED
LOW_AC_SUPPLY/LCD_BCKLED 6 D3001
RD2 54 5 DQ2 Q3000
EEPROM RD3 55 7 DQ3
IC304 RD4 57 8 DQ4
LIQUID CRYSTAL DISPLAY DRIVER
RD5 58 10 DQ5 IC3004
WE 7 46 EEWP RD6 59 11 DQ6
SCL 6 48 SCL RD7 60 13 DQ7 LIQUID CRYSTAL DISPLAY
LCD-OSC 10 7
14-28,30-36,38-47
RD0 ~ RD15 OSCIN ND3000
SDA 5 47 SDA RD8 69 42 DQ8 LCD-CLK 35 5 9 SCL 32
RD9 68 44 DQ9 LCD-SDA 40 10 SDA SEG0-SEG31 SEG0-SEG31
RD10 67 45 DQ10 LCD-CSB/TEST-MON38 38 8 CSB
7 XTALI
X301 RD11 66 47 DQ11 LCD-INHB(LCD_BCKLED)/FL-LATCH 134 13 INHB
27MHz RD12 65 48 DQ12
SERIAL FLASH 8 XTALO
RD13 64 50 DQ13 COM0 51
IC302
RD14 63 51 DQ14 4
COM1 52
RD15 62 53 DQ15 COM0-COM3
CS 1 30 SF_CS# COM2 1
SCLK 6 33 SF_CK COM3 2
SI/SIO0 5 32 SF_DI IFCS# 42 19 MTK-XIFCS
SO/SIO1 2 31 SF_DO IFSCK 34 17 MTK-CLK
S3100
IFSDO 35 20 MTK-SDI POWER-KEY 45 "/1
IFSDI 40 22 MTK-SDO
FOCUS/TRACKING COIL DRIVE, IFBSY 41 16 MTK-BUSY
SPINDLE/SLED/LOADING MOTOR DRIVE PRST# 38 15 MTK-RESET
IC401
139 USB-X1 S3101 S3102 S3103 S3104 S3105 S3106
USB SWITCH X104
FCS+ 14 VOFC+ x N - PAIRING MEGA BASS LIGHT MODE ENTER
VINFC 1 22 FOO IC453 48MHz
FCS- 13 VOFC- 140 USB-X2 BLUETOOTH
AD-KEY0 84
USB_DP 25 11 1D+ 2D+ 10 151 DP0
TRK- 15 VOTK+ S3107 S3108 S3109 S3110 S3111 S3112
VINTK 26 21 TRO USB_DM 24 3 1D- 2D- 4 150 DM0
TRK+ 16 VOTK- FUNCTION SOUND FIELD DJ EFFECT DJ EFFECT DJ EFFECT DJ EFFECT
FLANGER ISOLATOR DJ OFF SAMPLER
SP+ 11 VOSL+ S 2 60 USB_HOST_SEL
VINSL+ 4 17 DMO
SP- 12 VOSL- CN3203
D+ REC/PLAY
D+ 9
SL+ 17 VOLD+ D- S3113 S3114 S3115 S3116 S3117 S3118
VINLD 23 18 FMO D- 5
SL- 18 VOLD- VBUS PARTY CHAIN Z PARTY LIGHT FOOTBALL S3 S4
5V 1A
TUNING - TUNING +
BIAS 27 11 V14/VREF0 AD-KEY1 85
. >
USB+5V 6 2-IN 2+IN 5 152 VBUSIN0 S3119 S3120 S3121 S3122 S3123
MUTE 28 45 MUTE
S1 S2 VOCAL FADER MIC ECHO REC TO USB
2OUT 7 47 USB-OC - +
USB COMPARATOR
MS-476 BOARD IC452
BUS BUFFER
LOAD+ 10 VOTR+ FWD 6 122 CD-MOTOR+ IC102
(1/3)
LOAD- 9 VOTR- REV 7 124 CD-MOTOR- CN101
RXD1
DEBUG-RXD(MD-BOOT1) 64 8 3Y 3A 9 4 FOR
TXD1 SERVICE USE
3 6LJQDOSDWK
TRAY-IN 4 CDM-LOAD-SW
TRAY-OUT 3 CDM-UNLOAD-SW DEBUG-TXD 43 c : CD/DVD PLAY
d : USB
HCD-GT3D
33 33
HCD-GT3D
6-2. BLOCK DIAGRAM - AUDIO/VIDEO Section -
RV3100 MIC AMP J3200

IC3200
MIC LEVEL
CD RF AMP FOCUS/TRACKING ERROR AMP,
CD SYSTEM PROCESSOR, 7 OUT2 +IN2 5 MIC 1
DIGITAL SERVO PROCESSOR
IC301 SIGNAL SELECTOR
(2/2) IC913 3 +IN1 OUT1 1
ASDATA0 118 2 B SEL 6 J3201

ADIN 106 1 A Y 5 A/D CONVERTER AUDIO SELECTOR
IC606 IC605 GAIN CONTROL D3201
Q3200, Q3201 MIC 2
9 DOUT VINL 13 13 X X0 12
ACLK 112 6 SCKI
ALRCK 117 7 LRCK VINR 14 3 Y Y0 1
ABCK 113 8 BCK
SYSTEM CONTROLLER X3 11
VIDEO AMP IC101
IC901 (2/4)
Y3 4
CVBS 100 4 VIN
164 ANALOG-CSEL ANALOG-ASEL 41 AUDIO SELECTOR 10 A X1 14 13 LRCK/LOUT
POWER SAVE 1 2 VIDEO-MUTE DRIVER
J907
ANALOG-BSEL 42 Q604 9 B Y1 5 12 BCLK/ROUT
VIDEO OUT 2 VOUT
16 X1 CN2002
X600 FM ANTENNA
SIGNAL SELECTOR FRF1 1 2
12MHz FM
IC912 17 X2
DIGITAL AUDIO
INTERFACE RECEIVER 3 1B 1Y 4 28 SSI3_DI ST-DATA 128 11 DA
DIGITAL IC904
OPTICAL RECEIVER 10 3B 3Y 9 26 SSI3_LRCKO ST-CLK 127 8 CK
IC3300 13 4B 4Y 12 24 SSI3_BCKO ST-RDS 114 6 IIC/RDSI
DOUT 17 2 1A
OPTICAL IN FM RECEIVER
TV VOUT 1 31 RXIN4/ASCKI0 LRCK 18 11 3A SELECT 1 111 3D-RESET_ANALOG-DSEL/SD_D1_0
IC902
BCK 19 14 4A
67 RTC-X1 MIC-DETECT 173
X101
COPROCESSOR 32.768kHz A/D CONVERTER
IC105 68 RTC-X2 IC609
39 XTI
X602 SSI1_DI 55 9 DOUT
24.576MHz 91 AUDIO-X1 VINL 13
SDA SCL X103 AUDIO_CLK_OUT 14 6 SCKI
40 XTO
2 6 12.288MHz SSI0_BCKO 29 8 BCK
92 AUDIO-X2 VINR 14
SSI0_LRCKO 30 7 LRCK
MDI/SDA 24 126 DIR_CP-DATA
MC/SCL 25 125 DIR_CP-CLK
D/A CONVERTER
RST 34 165 DIR_RESET IC914
ERROR/INT0 1 130 DIR_INT0/EVOL_DATA
NPCM/INT1 2 136 DIR_INT1/AMP-CLK-FR SSI0_DO 32 14 DIN
OUTL 6 FRONT-L
12 SCK
70 EXTAL 13 BCK
X102 OUTR 7 FRONT-R
15 LRCK
13.333MHz
71 XTAL
SERIAL FLASH
IC106 >001B
D/A CONVERTER AMP
IC615 SECTION
SI/SIO0 5 170 Q-FLASH-SIO0 (Page 35)
4
SO/SIO1 2 172 Q-FLASH-SIO1 SSI1_DO 54 2 DATA
WP/SIO2 3 166 Q-FLASH-SIO2 16 SCK
HOLD/SIO3 7 167 Q-FLASH-SIO3 VOUTL 7 SW
1 BCK
3 LRCK
SCLK 6 168 Q-FLASH-CLK
CS 1 169 Q-FLASH-CS
NFC MODULE
(RC-S730 (WW)) D/A CONVERTER
IC604 AUDIO SELECTOR
SCL 131 NFC_CLK IC602 J602
DATA 132 NFC_DATA SSI2_DO 33 2 DATA
IRQ 12 NFC-INT 16 SCK VOUTL 7 1 Y0 Y1 5 L
OP AMP
RF-DET 53 NFC-RF-DET 1 BCK IN
IC603
3 LRCK VOUTR 8 12 X0 X1 14 R
AUDIO
PWR SUPPLY
PARTY CHAIN
CONTROL 8 BT-ON
Q104 LINK-OUT-A 176 AUDIO SELECTOR 10 A Y 3 L
OP AMP
DRIVER OUT
IC601
LINK-OUT-B 51 Q611 9 B X 13 R
BLUETOOTH
MODULE
+3.3V
3.3V PWR SUPPLY E+3.3V
Q103
BIAS DETECTION MUTING BIAS SET
BT-RESET 5 BT-RESET Q605, Q607 Q602, Q606 Q603
BT-TXD 133 BT-TXD
6LJQDOSDWK
BT-RXD 5 2A 2Y 6 65 BT-RXD(MD-CLK) LINK-DET 59 f : TUNER
/LINK-MUTE 94 N : MIC
BUS BUFFER LINK-SET 175
IC102 F : AUDIO (ANALOG)
(2/3)
L : AUDIO (DIGITAL)
E : VIDEO
HCD-GT3D
34 34
HCD-GT3D
6-3. BLOCK DIAGRAM - AMP Section -
POWER AMP
IC1001
OUT_A_52 52
4 INPUT_A
OUT_A_53 53
PRE AMP
SW L1006 LOUDSPEAKER
IC1005
OUT_B_44 44
5 INPUT_B
OUT_B_45 45
BIAS
+12V
>001B Q1022
TB001
AUDIO/VIDEO
SECTION
(Page 34) OUT_C_36 36 + L
FRONT-L 10 INPUT_C
OUT_C_37 37 - GREY
PRE AMP
L1007 MID/TWEETERS
IC1004
OUT_D_28 28 IMPEDANCE USE 2ȍ
FRONT-R 11 INPUT_D
OUT_D_29 29 + R
- PURPLE
15 SD
RELAY DRIVER
AMP RESET 20 M1 Q1021
SWITCH OVERLOAD OVERLOAD OVERLOAD
21 M2 D1008 RY001
Q1018, Q1019 DETECTION DETECTION DETECTION
Q1015, Q1014 Q1016, Q1017 Q1003, Q1004
2 RESET
DC FAN RESET FAN MOTOR

DETECTION SWITCH DRIVER M+13V
Q1006 Q1023 Q1010
D1017
CN1004
FAN 1 M
PROTECTION 2 DC FAN
Q1011
56 120 129 78 82
SD-FAST /AMP-RESET EVOL_CLK/RELAY_CONTROL AMP-PROTECT FAN_DET
SYSTEM CONTROLLER
IC101
(3/4) SLgQaO SaWK
F : AUDIO (ANALOG)
HCD-GT3D
35 35
HCD-GT3D
6-4. BLOCK DIAGRAM - POWER SUPPLY Section -
+9V REG +9V REG

IC004 IC006
+13V
A+13V PWR SUPPLY A+13V_GV2 A+13V_GV2 1 VIN VOUT 3 AVDD+9V, A+9V AVDD+9V 1 VIN VOUT 3 AVDD+5V
Q004
+12V REG +3.3V REG

IC1003 IC305 SYSTEM CONTROLLER
PWR SUPPLY IC101
A+13V_GV2 8 VCC VO 1 +12V DVDD5V 1 VDD VOUT 5 +3.3V
CONTROL (4/4)
Q461 5 EN DVDD3.3V 3 CE
57 PCONT-PSAVE-PROTECT
+1.2V REG
PWR SUPPLY +3.3V IC303
CONTROL E+3.3V PWR SUPPLY DVDD3.3V, FE_3.3V, FE_3.3V_1
Q012 Q005 DVDD3.3V 6 VCC VO 1 +1.2V
4 EN
SMPS BOARD +13V PWR SUPPLY

M+13V PWR SUPPLY SW+13V CONTROL 13 MTK-POWER-CTRL
Q011 Q457
13.5V M+13V
13.5V A+13V PWR SUPPLY
V1 PVDD DC-DC CONVERTER CONTROL
IC002 +5.2V Q006
M+5.2V PWR SUPPLY FE_5.2V_M, FE_5.2V_TRAY
M+13V 1 VIN1 SW1 3 E+1.18V Q459
5 EN1 VBST1 2
16 VIN2 VBST2 15 +5V
12 EN2 SW2 14 E+3.3V AVDD+5V PWR SUPPLY DVDD5V, FE_5V
Q007
+3.3V REG
DC-DC CONVERTER IC008
IC001
+3.3V AVDD+5V 4 VDD VOUT 3 AVDD+3.3V
M+13V 1 VIN1 SW1 3 USB+5V
E+3.3V PWR SUPPLY D+3.3V 1 CE
16 VIN2 VBST1 2 Q008
5 EN1 VBST2 15
12 EN2 SW2 14 M+5.2V, LED+5.2V +3.3V REG
IC903
PWR SUPPLY AVDD+5V 4 VDD VOUT 3 +3.3V
CONTROL
Q009 CE 1 115 ST-CE
96 PCONT-BTSTBY
52 VBUS-OE
~ AC IN
RESET
IC103
E+3.3V 2 VDD VOUT 4 76 REST
PROTECTION PROTECTION
E+3.3V CONTROL CONTROL 27 C-CONT
Q572 Q571
PROTECTION
CONTROL 79 SPM-C-MON
Q574
PROTECTION PROTECTION TH571

M+13V CONTROL CONTROL 80 SPM-AMBIENT-TEMP
Q575 Q576
MAIN ON 117 PCONT-DAMP
BUS BUFFER
IC102
(3/3)
AC OFF
AC-DET DETECT 12 4A 4Y 11 63 AC-CUT(MD-BOOT0)
Q107
HCD-GT3D
36 36
HCD-GT3D
Ver. 1.1
• Note for Printed Wiring Boards and Schematic Diagrams • Waveforms
- MOTHERBOARD Board -
Note on Printed Wiring Board: Note on Schematic Diagram:
• X : parts extracted from the component side. • All capacitors are in μF unless otherwise noted. (p: pF)
• Y : Parts extracted from the conductor side. 50 WV or less are not indicated except for electrolytics 1 IC001 2 (VBST1) 7 IC101 wh (SSI3_LRCKO) qd IC101 ua (XTAL)
• : Pattern from the side which enables seeing. and tantalums.
(The other layer’s patterns are not indicated.) • All resistors are in Ω and 1/4 W or less unless otherwise
specified.
Caution: • Components for right channel have same values as for
Pattern face side: Parts on the pattern face side seen left channel. Reference numbers are coded from
(Conductor Side) from the pattern face are indicated. • C : panel designation.
Parts face side: Parts on the parts face side seen from 3.4 Vp-p
(Component Side) the parts face are indicated. Note: The components identified by mark 0 or dotted line 15 Vp-p 3.7 Vp-p 75 ns
23 Ps
with mark 0 are critical for safety.
• MOTHERBOARD board is multi-layer board. Replace only with part number specified. 5 V/DIV, 1 Ps/DIV 1 V/DIV, 10 Ps/DIV 1 V/DIV, 25 ns/DIV
However, the patterns of intermediate layers have not
been included in diagrams. • A : B+ Line. 2 IC001 qg (VBST2) 8 IC101 wl (SSI0_BCKO) qf IC101 oa (AUDIO-X1)
• Indication of transistor. • Voltage and waveforms are dc with respect to ground
under no-signal (detuned) conditions.
C no mark : TUNER
• Voltages are taken with a VOM (Input impedance 10 MΩ).
Q These are omitted. Voltage variations may be noted due to normal production
B E tolerances. 16 Vp-p
• Waveforms are taken with a oscilloscope. 7.4 Ps 3.56 Vp-p 1.7 Vp-p
Voltage variations may be noted due to normal production 325 ns 81 ns
tolerances. 5 V/DIV, 1 Ps/DIV 1 V/DIV, 100 ns/DIV 500 mV/DIV, 25 ns/DIV
• Circled numbers refer to waveforms.
• Signal path.
c : CD/DVD PLAY
3 IC002 2 (VBST1) 9 IC101 e; (SSI0_LRCKO) qg IC101 os (AUDIO-X2)
BC E
These are omitted. f : TUNER
N : MIC
F : AUDIO (ANALOG)
L : AUDIO (DIGITAL)
Q
E : VIDEO
d : USB 16 Vp-p 3.4 Vp-p
B C E • Abbreviation 3.5 Vp-p
5.5 Ps 21 Ps
81 ns
These are omitted. AR : Argentina model
AUS : Australian model 5 V/DIV, 1 Ps/DIV 1 V/DIV, 10 Ps/DIV 1 V/DIV, 25 ns/DIV
E4 : African model
• Abbreviation EA : Saudi Arabia model 4 IC002 qg (VBST2) q; IC101 yj (RTC-X1) qh IC101 <zc. (USB-X1)
AR : Argentina model LA9 : Latin-American model
AUS : Australian model MY : Malaysia model
E4 : African model RU : Russian model
EA : Saudi Arabia model TH : Thai model
LA9 : Latin-American model
MY : Malaysia model
Note 1: When the MS-476 board is defective, exchange the 1 Vp-p
RU : Russian model 30 Ps
entire LOADING COMPLETE ASSY (T). 16 Vp-p 630 mVp-p
TH : Thai model 3.8 Ps 21 ns
5 V/DIV, 1 Ps/DIV 500 mV/DIV, 10 Ps/DIV 200 mV/DIV, 10 ns/DIV
Note 1: When the MS-476 board is defective, exchange the Note 2: When the complete DAMP board is replaced, refer to
entire LOADING COMPLETE ASSY (T). “NOTE OF REPLACING THE IC1001 ON THE DAMP
BOARD AND THE COMPLETE DAMP BOARD” on 5 IC101 qf (AUDIO_CLK_OUT) qa IC101 yk (RTC-X2) qj IC101 <zv/ (USB-X2)
servicing notes (page 5).
Note 2: When the complete DAMP board is replaced, refer to
“NOTE OF REPLACING THE IC1001 ON THE DAMP
Note 3: When the C1126, C1127, C1128, C1129, C1142,
BOARD AND THE COMPLETE DAMP BOARD” on
L1010 and RY001 on the DAMP board are replaced,
spread the bond referring to “BOND FIXATION OF
ELECTRIC PARTS” on servicing notes (page 6). 1.6 Vp-p 480 mVp-p
3.6 Vp-p
30 Ps 21 ns
Note 3: When the C1126, C1127, C1128, C1129, C1142, 81 ns
L1010 and RY001 on the DAMP board are replaced, 1 V/DIV, 25 ns/DIV 500 mV/DIV, 10 Ps/DIV 200 mV/DIV, 10 ns/DIV
ELECTRIC PARTS” on servicing notes (page 6).
6 IC101 wf (SSI3_BCKO) qs IC101 u; (EXTAL) qk IC301 7 (XTALI)
3.6 Vp-p 1.7 Vp-p

355 ns 75 ns 640 mVp-p
37.5 ns
1 V/DIV, 100 ns/DIV 500 mV/DIV, 25 ns/DIV 200 mV/DIV, 25 ns/DIV
HCD-GT3D
37 37
HCD-GT3D
ql IC301 8 (XTALO) wg IC604 3 (LRCK) ea IC609 7 (LRCK) ej IC902 qj (X2) rd IC912 0 (3B) rl IC914 qd (BCK)
3.4 Vp-p 3.4 Vp-p 290 mVp-p 3.4 Vp-p 3.8 Vp-p
740 mVp-p 350 ns
37.5 ns 22 Ps 22 Ps 85 ns 22 Ps
200 mV/DIV, 25 ns/DIV 1 V/DIV, 10 Ps/DIV 1 V/DIV, 10 Ps/DIV 100 mV/DIV, 50 ns/DIV 1 V/DIV, 10 Ps/DIV 2 V/DIV, 250 ns/DIV
w; IC301 <zzx (ACLK) wh IC604 qh (SCK) es IC609 8 (BCK) ek IC904 qk (LRCK) rf IC912 qa (3A) t; IC914 qg (LRCK)
3.3 Vp-p 3.8 Vp-p

4 Vp-p 81 ns 3.4 Vp-p 3.4 Vp-p 3.4 Vp-p
60 ns 350 ns 22 Ps
375 Ps 375 Ps
1 V/DIV, 25 ns/DIV 1 V/DIV, 25 ns/DIV 2 V/DIV, 250 ns/DIV 1 V/DIV, 250 Ps/DIV 1 V/DIV, 250 Ps/DIV 1 V/DIV, 10 Ps/DIV
wa IC301 <zzc (ABCK) wj IC606 6 (SCKI) ed IC615 1 (BCK) el IC904 ql (BCK) rg IC912 qs (4Y)
3.8 Vp-p
3.8 Vp-p 4 Vp-p 3.4 Vp-p 3.8 Vp-p
359 ns 60 ns 350 ns 5.75 Ps 359 ns
1 V/DIV, 100 ns/DIV 2 V/DIV, 50 ns/DIV 2 V/DIV, 250 ns/DIV 1 V/DIV, 2.5 Ps/DIV 1 V/DIV, 100 ns/DIV
ws IC301 <zzm (ALRCK) wk IC606 7 (LRCK) ef IC615 3 (LRCK) r; IC904 el (XTI) rh IC912 qd (4B)
3.4 Vp-p 3.4 Vp-p 3.4 Vp-p 1.75 Vp-p 3.8 Vp-p
22 Ps 22 Ps 22 Ps 40 ns 359 ns
1 V/DIV, 10 Ps/DIV 1 V/DIV, 10 Ps/DIV 1 V/DIV, 10 Ps/DIV 500 mV/DIV, 25 ns/DIV 1 V/DIV, 100 ns/DIV
wd IC301 <zxc (RFIP) wl IC606 8 (BCK) eg IC615 qh (SCK) ra IC904 r; (XTO) rj IC912 qf (4A)
3.9 Vp-p 3.4 Vp-p

81 ns 3 Vp-p 3.4 Vp-p
1 Vp-p 350 ns 40 ns 5.75 Ps
200 mV/DIV, 500 ns/DIV 2 V/DIV, 250 ns/DIV 2 V/DIV, 250 ns/DIV 1 V/DIV, 25 ns/DIV 1 V/DIV, 2.5 Ps/DIV
wf IC604 1 (BCK) e; IC609 6 (SCKI) eh IC902 qh (X1) rs IC912 9 (3Y) rk IC914 qs (SCK)
3.5 Vp-p 3.4 Vp-p 3.4 Vp-p

81 ns 140 mVp-p 3.4 Vp-p 81 ns
320 ns 85 ns 22 Ps
1 V/DIV, 100 ns/DIV 2 V/DIV, 50 ns/DIV 50 mV/DIV, 50 ns/DIV 1 V/DIV, 10 Ps/DIV 2 V/DIV, 50 ns/DIV
HCD-GT3D
38 38
HCD-GT3D
Ver. 1.1
6-5. PRINTED WIRING BOARD - MOTHERBOARD Board - • See page 32 for Circuit Boards Location. • : Uses unleaded solder.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
AUDIO
PARTY CHAIN
ANTENNA VIDEO FOR
MOTHERBOARD BOARD MOTHERBOARD BOARD

FM L R OUT SERVICE USE
A (COMPONENT SIDE) IN
OUT
(CHASSIS)
IN
OUT (CONDUCTOR SIDE)
(CHASSIS)
CN101
JL635
C980
CN2002 J907
C1001
2 1
JL515 JL514 JL907
5 1
JL639
C1002
J602
JL640 JL516
JL638
JL518
R566
JL195 R543
JL519
R504
C530
JL630 R937 JL631 JL103 JL522
D600
B
C930 L603
L602 JL520 R567 R264
R534
R938
R935
R260
R952
C1003
JL523
C932
24 13
R503
R506
R507
R959
R957
L604 C905 R951
JL217 IC502
R995
C933
JL521
C511
C931
C541
FL601
24 13 R950
R996 25 12 JL525 1 12
C934
C935
R940 5 1
C904
6 20 C526
C945
IC904 R541
R515
IC90216 C906 C928
R511
R939 4 3
C950
X600
4
10 C647 C650 C960
R510
C936
CN517
>007P
11 15
R663
C641
6 1
C652
R552 R564
C643
C528 R514
R569
36 1
C937
R944 JL905 IC901JL904
R669 R671
37 48
R914
R685
C938
C657 C958 JL528
R905
R542
C956
C957
JL634 JL606 SPK_HLED R549 R555
1
R943 R954 R953
C527
R662
JL110 JL111 BOARD
R949
JL604
C357
C358
C943
L605
R381
R912
JL620
C941 R686 R911 C953 JL529
CN4000
X602 54 28
R859 (Page 56)
C638
C658
4 3 R955 JL637 C660 C665
IC903 JL605 1 6
C532
C RB306 RB307
R689
R913
C951 C952
R651
1 2
JL619 C954
C631
C602
RB304 RB301 CL338 3 4
IC306
C364
Q605
R380
R379
C917
C944 JL636 FB320
JL339
R857
C348
R382
C359
C347
C346
3 1 3 1 CL337
R369
JL290 (CHASSIS)
C362
FL301
CN602 RB303 RB305 RB302 CN602
C363
R368 JL206
RB308 Q607 R692
R700
IC304
1 27
CL336 1 6
R364
C352
R370
C345
FB321
R366
96 65 5 4
RB309 CL330 3 4
R377
97 64
R376
C365
C360
4 3
C350
(CHASSIS) JL056 Q603
R650 C629
R363 JL332 C354 CL334 CL333 6 1
R319
R752 R367
R346 R374
C626 R321 8 1 JL906 JL335 R373 R359 CL329 CL321 C628 Q602
R361 C344 CL332 CL316 C966 6 1
R036 JL334 C349
R628
CL315
R356 JL338 R360
R753 C342 C343 CL319
R627
C076
JL057 C627 R350 R388 JL337 JL333 JL351 R365
R756
JL336 R362
R357
R387
CL320
C330 C340
C339
4 3
IC301 CL318 CL331 R653
>001P R347 R330
C341
R355 JL355 R348 R390
CL335
R751
R354 C369 CL314

R750 C338
C331
R345
R343
C326
C325
CL408 C407
IC302 R358 R641
D OPTICAL BOARD C337
R352 R415 SL403 C315 C336
R624
R625
JL350
R303 R302
C334 5 4 C372
R344
CL401
C651
R402
C621
C620
CN3300 C411 R411
R328
128 33 JL349 SL402 CL311 CL309 C328
R351
R349
R606 1 32 C402 CL402

1 28 1 6
R696
(Page 55) JL354 R659
R326
CL403
R371
R342 C403 CL307
R378
C316 R666
R418 C413
3 4
R684
R329 C324
SL401 SL404 R401 CL412 CL322
C661
C637
R372 C319 R665
R408
1 23 CL404
R621
R642 R340 CL317
L301
C355 R332 8 1 JL348 JL347 C373 CL312
R644 R915 C353 JL404 CN302 IC401 CL409 1 16
R322
R334 R406
R658 R327
C321 IC303 CL313
R496
JL346 2 24
C409
7 22
C766
R694
R335
R339
1 8 5 CL308 CL310
IC305
R337
4
R407
IC605
R649 R916
R693 R682
C356
CL405
X301 JL353
C412
C401
1 3
CL411
C606
IC601 R331 JL352 R463
R681
R698
JL330 29 30
8 9
C656
R616
4 5 C322 C323 CL407 R697
C640
C310
C309
R600
JL331
CL410
R404
C648
C404
JL318
CL406
C408
R607 Q604 JL341
SL301
8 21
C767
3 1
R615 JL609 R661
C644
JL321
R301
R389
C605 R608 JL305 JL470 SERVICE, C642 R674
R409
C612
C601
JL611 JL326
C646
JL329
JL328
JL317
C311
4 6
C645 JL464 OPTICAL DEVICE(7G)
SL408
C462
C616
C653
SL405
SL407
C607 1 14
R634 R646 JL309
2 4 R633 JL301 2 4 R688
R677
SL406
14 15
JL403 R559 R645
IC606
1 16
CN303 R611 CN303 C419 R410 R603
E
C649
C655
R317
JL401
JL313
JL311
JL402 R316
1 5 R612 JL303 1 5 JL406 7 8
C465
R466
R467
C418 R691
C664
JL602 R648 R604

JL315
JL319
JL327
JL601 C463 R465 C307

IC602 JL307
JL405
R687
R636
6 4
JL323 JL325 C308 R690
Q611 R605
R313
R312
C302
R318
R310
R613 1 3 1 23 JL452
R472
R470
8 9 R639 CN302 R464
R478
1 8
R602 6 1 6 1
JL324
R702 JL454
C303
R647 R982 2 24 CN401 CN401
R051
R052
JL451
R801
D402
JL302
JL306
JL310
JL314
4 5
R610 R635 R838
C074
C075
C406
C405
JL455 1 14 C977
R577
R963
MS-476 BOARD R835 JL458 JL457 IC452
C468
1 16
D401
C366 JL320 JL322 IC453
C989
R964 1 8
R836
R500
JL469
FB455
R583
C466
R498
R585
R586
IC912 IC913
R480
JL050
C464
R837 7 8 Q402 Q401 R424 4 5
C421
C424
JL308
C618
JL304
JL312
JL316
C614
R839 B R429 B R965

R626
8 9 JL461 JL459 R054

C467
R966
R471 C073 C066 JL055
C367
R433 CL415 E CL414 E

R840
C613 JL463
JL462 JL460 JL456
JL023
R053 CL413
R802
R701
R622 C615
C625
C610
JL295
R432
R617
C634
C608
R048
R421
R422
R981 C064
R431
1 8
R430
R428
R427
R426
R425
R423
JL296
R980
R386 C071
R619
R638
F JL032 R030
JL022
R654
R652
CN451 IC603 CN451
JL021
R028
R640
1 6
C420
C423
R618
R609
1 8 1 8 B E
4 5 Q007 (CHASSIS)
C604 C603 C630 C624 C633 C635 B E 3 4 Q459
R791
R614 R655 Q457 JL024
R295
R034
R620
R656
R219
R039
B
C632 C619 R211
R254
R257
R261
E
R218
R040
C067
R215
R198
R581
R037
JL282
B
JL182
R232
E
Q006
R643
R629
R579 Q005 R213

JL190
R582 R274
C065
R580
JL059
R229
R224
JL189
R299
JL187
R150
JL185
>002P IC604
R193 JL281
JL183
R230
C622 R210
JL222
9 8 JL603
R221 C139
R538
R270
C617
C295
R265
C017
JL193 R267 R263
R164
R181
R119
C609 JL179
R273
MIC BOARD R163 JL163 JL001

JL212
R630
JC001
R271
R272
R226
JL209
JL294
JL211
L001
JC002
CN3201 R631 R948 JL293 R197 R251 R237
C662
JL292
R201
JL298 JL278
R168 R255
C299
R242 FB115 FB116
(Page 56) JL612
JL297 JL210
R284
C143
R716
R283
R711
16 1 JL632 C080
R820 JL161 R002 R183 R587 R247 C296
C003
JL616 R632 R059 C005
JL162
44 1 176
JL288 R169 45 L003
R268
C168 R234
R216
JL618
C153
R259
R576
C148
C146
R300
R170
JL285 R111 IC102
C137
C135
C133
R172 C111 R588
R256
C019
5 4
4 1 4 1 R103 JL164 IC101 R293 8 1 R112 R222
C142
C141
C140
8 7
C013
CN601 CN601 R173 R110 R294
R135 R129
R133
IC001
C1000
JL149
C691
R134
R120
R575
JL269 R292
R589
R116 R286 R107 R131
R291
C673
C030
R125 9 16
R123 C109 JL268 JL299 IC106 R287
R139
R143
8 1 14 1
L008
C040
C154 C112 IC609 C669 R709
C102
JL613 JL614 JL615 JL300

C279
C695
R023 C035
R132
R102 C106 R289
C113
C278
C674
C679
C052
JC003 C049
X101 C164 R290 C155 1 14 C667

R590 R031 R020 C114
R285 R288 C156 C666
R718
C115
R720
R137
R185
JC004
C678 R708
R140
C127 C126
L006 R723 C670

C157 C281 C120
C672
C298
C297
7 8
JL003 C158 C118 R175 C121 C122
C079
R188
C081 R024 C123 R719

R186
>003P X102
R127
R176
C151
JL158 JL160
R192
R167
R195
R253
R250
C117 C116 FB101 R722
R275
C986
C159
JL159
C160 C280
MIC BOARD R153 JL150 R149
R269
C144
C138
C136
X104
C083
R063
JL244 JL049 C282

R733
CN3200 R154 JL166

C084
R225
R223
JL255
JL214
JL213
(Page 56) R155 JL188 JL191 R761 R762

H
R760
R817
C152
R909
E E B
C134
C131
R156 R276 FB117 C147
R115
R298
JL165 88 133
Q009 JL044 R572 C128
R117
R830
C689
R061
JL276
B
R177 89 132
R174 R280 R278 R279
C034 R062
C995
R978
R282
R190
JL256 Q008 R194
R178
JL186 JL207 JL272 C129 R146 20 11
JL168
JL275
JL184
B E
R200 JL041 R297 R245 R145
R747
C998
R179 R196
R236
C690
R243
Q107 R189 IC914
JL208
C922
R171 JL283
JL167 L007
R206
R204
R202
R180 R144 R829
R166
JL271
JL273
JC007
C050 JC008
R227
R106
R114
R159
R104 C165
C110
R212
R763
JL280
R238
C077
1 10
X103
JL227
R574
JL116
R233
R160
C696 JL274 1 8 R228 C983

R158 R157
C994
R105
R252
R248
R246
R244
C162
R126
R241
C161
R161
R214
R220
R191
B
R128 C130
C053
R043 C166 C997

C699
4 5 R826
C032
C149 R041 C982

IC105
E
C132 JL134
C039
D102 JL224
R217
R100
JL068
C704
JL228
Q606 C996
C692
JL289
R827
R099 JL178 JL225
R203 8 1
C104
JL148
R122
C107
3 2 JL169 JL270 JL004
JL197 JL131 JL132 IC002 C993
C014
IC103
C748
R113
JL201 JL199
C150 Q572
C021
C103 4 1 R087
C105
JL172
C006
C004
C749
9 16 E B
JL173 JL048
C078
R831
16 9
JL067 C574
D571
I JL194 R003
R491
R483
L004
C744 C101 JL176 JL175 JL174 JL135 R006 C036
R485
JL171 R819 IC615
C018
JL203 JL151
D572
E B
C726
JC005
B E
L002
C742
C100
C167 R795
C984
3 2 Q571 S
Q575 Q576
JL240 IC008
C573
B 1 8
JL202 JL204 R571
C577
R487
C088
G
JC006
1
E
4 1 JL170 R479 Q574 R796 R793
2
JL239 R797
JL040
R035
R033
R794
JL008
Q012
C068
C072 JL007 JL005 JL152 E B
B E
JL198 JL215 JL235
R085
JL617 R029 Q461
JL241 JL106 R066
C087
IC004 IC006
C051
JL205
>004P JL105 JL216 R065 E B
C284
JL200 JL153
JL113 JL114 JL107 JL026
C085
JL196
C062
B
CN119
R064
JL045 JL006 Q004 1 3 1 3
C057
TH571
DAMP BOARD JL259 JL046

C024
E
JL247 JL248 R142 JL047 JL155
CN1001 JL140 JL136
6 2
R489
6 2
Q011
(Page 50) JL115 R086
JL108
J
5 1 5 1
10 2 JL249 10 2 JL139 CN105 CN105 Q104
CN102 JL251 CN102 JL137 C010 C092 R792 E B B E Q103
JL141 JL133
18
9 1 9 1
JL112 JL231 JL154 C011 C091
JL252 JL242
19
JL129 R109 R108

JL145
JL264 JL053 JL146 JL054
JL104 25 1
JL109 JL287 JL143 NFC MODULE
CN118
JL265 24 2 CN001 (RC-S730 (WW)
JL291 JL284 1 9
BLUETOOTH MODULE JL130
R080
JL144
JL230
JL142
JL147
JL232
JL138
JL286
(CHASSIS)
K
11 11
(CHASSIS)
>005P >006P
(11) (11)
SPLITTER BOARD SMPS BOARD
CN3400
(Page 58)
(Page 50)
1-894-133- 1-894-133-
Note 1: IC001, IC002, IC101, IC105, IC106, IC301, IC302 and IC303 on the Note 2: When the MS-476 board is defective, exchange the
MOTHERBOARD board cannot exchange with single. When these parts on the entire LOADING COMPLETE ASSY (T).
MOTHERBOARD board are damaged, exchange the entire mounted board.
HCD-GT3D
39 39
HCD-GT3D
Ver. 1.1
6-6. SCHEMATIC DIAGRAM - MOTHERBOARD Board (1/10) - • See page 59 for IC Block Diagrams.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
A MOTHERBOARD BOARD (1/10)
11 >011S
LINK-DET
MOTHERBOARD
BOARD
(9/10)
(Page 48)
/LINE-MUTE
B
R624 2.2k JL635
J602
0.1 0 4P
C1001 C980 C1002
0.001 220p 0.1
0.2 Q602
3.4 IMX25T110
MUTING LINEOUT LEFT JL619 IN
L
Q606 JL604 OUT
LTA014EUBFS8TL 0 0.1 R756 AUDIO
C D+3.3V
MUTING 3.4
6.8k PARTY CHAIN
>001S 1 LINEOUT RIGHT JL620 IN
R
MOTHERBOARD R625 2.2k JL605 OUT
BOARD
(2/10), (3/10),
(4/10), (8/10), R913 C657 R686
R628 4.7k GUEST L 68k 4.7 120k
(10/10) R752 C626
(Page 41), (Page 42), 100 10 LINEOUT LEFT
(Page 43), (Page 47), C620 47 R750 100
(Page 49) R627 4.7k C652
R914 MOTHERBOARD
C621 R751 C627 GUEST R 68k 4.7 BOARD
R753
47 100 100 10 LINEOUT RIGHT (7/10)
D C606 0.1
R792
0 AVDD+9V
(Page 46)
9 >009S
R912 470k C665 2.2
R911 470k R651 150k
R606 R621 R653 AGND
0 0 6.8k 10 >010S
IC601 Q605 Q607 MOTHERBOARD
BA4558F XP4501 R685 RN4902 (T5RSONY, D, F) BOARD
BIAS DETECTION 120k (7/10)
R915
IC601 R916
C628 2.2 R650 22k
5.1
BIAS DETECTION
3.4
(Page 46)
15k
E 4.7k OP AMP 4.7k R641
C647 0
R700 22k
R642 4.6 9.1 R649 C650 0
C629 10 0 5.1
1 OUT VCC 8 4.7 4.7
27k 27k 5.1 0 R692 A+9V
4.6 4.6
5.1 R689 C660 22k 0 5.1 8 >008S
2 - OUT 7 R662 R671 150k 2.2
C601 56k MOTHERBOARD
5.1 0 LINK-SET 56k BOARD
4.7 4.4 4.5
3 + - 6 R663 680k R669 680k C917 10 (3/10)
C612 5.1 (Page 42)
4.5 4.7 C641 10p C643 10p
4 GND R600
+ 5 68k Q603
R644 RN4902(T5RSONY,D,F)
68k
R607 470k R615 470k BIAS SET
F C766
4.7
R608 4.7k R616 4.7k
C767
4.7
7 >007S
C607 0.1 C605 47 6.3V MOTHERBOARD
TUNER-R
TUNER-L
BOARD
(2/10)
(Page 41)
Q611
RN1902
AUDIO SELECTOR
DRIVER CN601
LINK-OUT-B 4P
R711
1k JL613
4 A+9V
G IC602
SN74LV4052APWR
JL614
3 MIC GND
>037S
0 3.4 LINK-OUT-A C662 4.7 R716 1k JL615
2 MIC SIGNAL
IC602
4.7
4.7
MIC
JL632 JL603 JL616
4.7
4.7
AUDIO SELECTOR 0 1 MIC DET BOARD
CN3200
(Page 57)
C658
C661
R982 0
C638
C637
8 GND B 9
R681 1M R693 1M
0 R639 47k
7 GND A 10 R658 1M R665 1M R682 47k R694 47k
MIC SIGNAL
2.4 JL602 R659 47k R666 47k R684 47k R696 47k 6 >006S
6 INH X3 11
MOTHERBOARD
H 2.6
5 Y1 X0 12
2.6 BOARD
(3/10)
JL601 2.6 5.1 (Page 42)
2.6 2.6
4 Y3 X 13 1 Y0 VCC 16
2.6
C651
2.6 C631 4.7 GUEST R 0.1
3 Y X1 14 2 Y2 X2 15
R 2.6 0.3
2.6 2.6
2 Y2 X2 15 3 Y X1 14
2.6 5.1
C616 2.4 2.5
1 Y0 VCC 16 0.1 4 Y3 X 13
0.2 2.6
5 Y1 X0 12
I R602 47k R610 47k R633 47k R645 47k
2.4
R603 47k R611 47k R634 1M R646 1M 6 INH X3 11
C656 0.22 IC605
R604 47k R612 47k R635 47k R647 47k SN74LV4052APWR 0 R698 47k
C966 0.22 7 GND A 10 MIC-DET
R605 1M R613 1M R636 47k R648 47k
IC605 0 R697 47k VCC5V
C602 4.7 GUEST L AUDIO SELECTOR 8 GND B 9 0 0
5 >005S
MOTHERBOARD
JL609 3.4 JL611 ANALOG-ASEL BOARD
L (2/10), (3/10),
3.4 (4/10)
(Page 41), (Page 42),
ANALOG-BSEL (Page 43)
J
Y0
X0
Q604
RN1902
>002S 2 AUDIO SELECTOR
MOTHERBOARD DRIVER
DGND
BOARD 4 >004S
(3/10)
(Page 42) MOTHERBOARD
BOARD
(2/10), (3/10),
(4/10), (5/10),
(6/10), (7/10),
(8/10), (9/10),
(10/10),
(Page 41), (Page 42),
K >003S 3 (Page 43), (Page 44),
(Page 45), (Page 46),
MOTHERBOARD (Page 47), (Page 48),
BOARD (Page 49)
(4/10)
(Page 43)
HCD-GT3D
40 40
HCD-GT3D
Ver. 1.1
6-7. SCHEMATIC DIAGRAM - MOTHERBOARD Board (2/10) - • See page 37 for Waveforms. • See page 59 for IC Block Diagrams.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
MOTHERBOARD BOARD (2/10)

A E+3.3V
30 >030S
M+13V
>013S 13 MOTHERBOARD
BOARD
MOTHERBOARD (7/10)
BOARD (Page 46)
(4/10), (7/10)
(Page 43), (Page 46)
>012S 12
MOTHERBOARD D+3.3V
B BOARD
(4/10)
Q008
1 >001S
(Page 43)
KTA1542T-RTK/P MOTHERBOARD
+3.3V PWR SUPPLY BOARD
DIR_CP-DATA JL636 R957 10 R950 10 DIR BCK 3.4 3.3 JL049 (1/10)
(Page 40)
DIR_CP-CLK JL637 R951 10 DIR LACK
DIR_RESET R952 10 DIR DATA R061 2.6
10k
3.4 3.4 1.7 1.7 0
24 23 22 21 20 19 18 17 16 15 14 13 C084 C083
R062
220 100 16V 0.1
MDI/SDA
MDO/ADR0
DVDD
DGND
SCKO
BCK
LRCK
DOUT
MPO1
MPO0
MPIO_B3
MPIO_B2
R063 0.1
Q009
C FL601
2
3
PCONT-BTSTBY 0 3.3
KRC402-RTK 16 >016S
JL044 PWR SUPPLY MOTHERBOARD
1
3.4
39 38 CONTROL BOARD
R959 10 (6/10)
25 MC/SCL MPIO_B1 12 (Page 45)
26 MS/ADR1 MPIO_B0 11
Q011
27 MODE MPIO_C3 10 KTA1542T-RTK/P
28 RXIN7/ADIN0 MPIO_C2 9 +13V PWR SUPPLY
CN602 IC904 13.7 13.7 JL059 SW+13V
3P 29 RXIN6/ALRCKI0 PCM9211PTR MPIO_C1 8 14 >014S
D VCC 3
R949 100 0.3
30 RXIN5/ABCKI0 IC904 MPIO_C0 7 R064
68k
MOTHERBOARD
BOARD
>038S VOUT 2 31 RXIN4/ASCKI0 DIGITAL AUDIO MPIO_A3 6 13
(10/10)
C945 INTERFACE RECEIVER (Page 49)
OPTICAL GND 1 47p 32 RXIN3 MPIO_A2 5 R066 R065
BOARD 3.3k 3.3k C088 C087
CN3300 33 RXIN2 MPIO_A1 4
(Page 55) 3.4 220 16V 0.1
C958 34 RST MPIO_A0 3 0.1
0.01 0 0 DIR_INT1 PCONT-PSAVE-PROTECT 3.3 Q012 MOTHERBOARD
35 RXIN1 NPCM/INT1 2 BOARD
C950 3.4 3.4 DIR_INT0/EVOL_DATA KRC402-RTK (7/10)
10 JL265 PWR SUPPLY
DGND C944 1 36 VDDRX ERROR/INT0 1 (Page 46)
>004S 4 CONTROL
MGND
MOTHERBOARD
40 41 15 >015S
AGNDAD
BOARD
E
GNDRX
VCCAD
VCOM
RXIN0
(1/10)
AGND
VINR
VINL
VCC
XTO
FILT
(Page 40)
XTI
M+5.2V
31 >031S
37 38 39 40 41 42 43 44 45 46 47 48 FE_5.2V_M
R051 0 MOTHERBOARD
1.8 1.8 3.4 0 0 0 BOARD
5.4 5.4 JL050 R052 0 FE_5.2V_TRAY (7/10), (10/10)
100p
100p
R028 Q459
10k KTA1542T-RTK/P C064 C066 C074 C075
4.7 0.1 100 10V 0.1 0.1
C956
C957
R954 1M C953 +5.2V PWR SUPPLY
0.0047
X602 R953
24.576MHz 560
F
0.1
R054 0 FE_3.3V_1
R955 18 >018S
680
C960
MOTHERBOARD
C951 C952 C954 Q005 BOARD
10p 12p (6/10)
0.068 KTA1542T-RTK/P
+3.3V PWR SUPPLY (Page 45)
3.4 3.3 DVDD3.3V
17 >017S
R037 MOTHERBOARD
10k 2.6 BOARD
Q007 (5/10), (6/10)
KTA1542T-RTK/P (Page 44), (Page 45)
R859
0 +5V PWR SUPPLY R048
G >005S 5
VCC5V 5.1 5.1 JL032 0 DVDD5V
19 >019S
MOTHERBOARD
BOARD R039 MOTHERBOARD
(1/10) C938 C941 10k 4.4 BOARD
(Page 40) 10 1 JL022 JL024 (4/10), (5/10)
3.4 5.1 (Page 43), (Page 44)
L605 R030 R034
2.2nH C934 C935 C937 3 4 Q457 680 220
R857 C933 0.0022 1p 1p C943 RN1911 R053 0 FE_5V
R938 10p 20 >020S
VOUT
VDD
0 0 1 PWR SUPPLY JL023 R040

AGND
>010S
100 10V
100 10V
10 CONTROL 470 MOTHERBOARD
0.1 0.1
MOTHERBOARD
0.1 BOARD
Q006
0.1
X600 IC903 JL021 3.3 (6/10)
H 3.3 3.3
1
BOARD MM3411A33URE KRC402-RTK
(7/10) 12MHz (Page 45)
PWR SUPPLY
(Page 46) 3.4 3.4 0.1 0.1
IC903 CONTROL
C065
C067
C071
C073
20 19 18 17 16 +3.3V REG
VDDRF
GND_19
VDD_18
X2
X1
JL638 MTK-POWER-CTRL
GND
AVDD+5V
>021S
CE
21
L603 C930
68nH 68p 2 1 MOTHERBOARD
100
JL630
C932
0.047 0
37 36 3.4
BOARD
(3/10), (7/10)
Q575 (Page 42), (Page 46)
1 CP2 CP1 15
R937
L604 C931 0 Q572 13.7 LTA014EUBFS8TL

CN2002 D600 IC902 ST-CE PROTECTION
2P 68nH 47p 2 FRF1 RN5B801-0002 IISD 14 KTA1542T-RTK/P
BAV99-215 CONTROL
I ANTENNA GND 1
0
3 GNDRF IC902 LRCK/LOUT 13
1.6
1.5
TUNER-L PROTECTION
CONTROL 0
FM R996 0 TUNER-R 3.4 3.4

FM 2 4 ARF1 FM RECEIVER BCLK/ROUT 12
R995 0 0 3.4 ST-DATA 13.7
R943 22
5 ARF2 DA 11 D571
DA2J10100L R485 R483
2.9 1k 1k
R489 R571 D572 12.4
IIC/RDSI
GND_10
6.8k 220k DA2J10100L

VDD_9
CK
LA
SPM-AMBINET-TEMP TH571 R479 3.4 3.4 SPM-C-MON

6 7 8 9 10 220k Q576
1000 6.3V
L602 0 KRC402-RTK
J 47nH
3.4 3.4 3.4
C-CONT 3.3 Q571
KRC402-RTK Q574 0 PROTECTION
2.2M
RHK005N03T146 3.2 CONTROL PCONT-DAMP
PROTECTION PROTECTION
CONTROL CONTROL
R939 C936 C573
10k 0.0022 R491 C574
C577
R487
0.1 10k 0.1
R940 R944
100 22 ST-CLK
ST-RDS
11 >011S
>007S 7
K MOTHERBOARD
MOTHERBOARD
BOARD
BOARD (9/10)
(1/10) (Page 48)
(Page 40)
HCD-GT3D
41 41
HCD-GT3D
Ver. 1.1
6-8. SCHEMATIC DIAGRAM - MOTHERBOARD Board (3/10) - • See page 37 for Waveforms. • See page 59 for IC Block Diagrams.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17

AVDD+5V
21 >021S
B MOTHERBOARD
BOARD
(2/10), (7/10),
R719 10 DIN1
R718
MIC SIGNAL JL612 C666 4.7 R708 47 0 R722 10 ARAGON-BCK0
>006S 6
MOTHERBOARD C667 4.7 R709 47
BOARD
(1/10) 2.5 2.5 0 1.6 1.7
(Page 40) 32
14 13 12 11 10 9 8
C IC609 2 >002S
VINR
VINL
FMT
MD1
MD0
DOUT
BCK
PCM1808PWR
MOTHERBOARD
Y0
X0
IC609 30 BOARD
0.001
0.001
(1/10)
DGND
AGND
VREF
LRCK
A/D CONVERTER
SCKI
(Page 40)
VCC
VDD
1 2 3 4 5 6 7
C670
C669
C672 10 16V 2.6 5.1 3.4 1.7 1.7

31
C673 0.1 R723 10 ARAGON-LRCK0
C674 C678
0.1 0.1
R720 10
D C986
10 16V
C679
10 C618 10 16V A+9V
D+3.3V 8 >008S
>001S 1
C613 0.1
MOTHERBOARD C1000 MOTHERBOARD
BOARD 10 16V C610 BOARD
C691 C695 4.7 C614 47 6.3V
(1/10) 10 16V 0.1 (1/10)
(Page 40) R622 4.7k R626 4.7k (Page 40)
DGND C993 0.1 JL618 C615 0.1

>004S 4
680p
4.7k
47p
10k
4.7
MOTHERBOARD C726
BOARD 470 6.3V 4.6 9.1
(1/10) R733
R640
C633
C625
C635
R655
E (Page 40) 0 JL617 R617
1.5k 4.6
1 OUT VCC 8
4.6
R794 R609 4.7k
2 - OUT 7
0 R638
4.6 4.6 1.5k C634
C603 680p 3 + - 6 820p
4.6
R618 4 GND + 5
2.7k R652 R654
2.7k 2.7k
C608 820p IC603
BA4558F
>010S 10
AGND R619 IC603
F MOTHERBOARD ARAGON-LRCK0 C604 47p
2.7k OP AMP
BOARD
(7/10) R614 10k R620 3.3k C632 47
ARAGON-BCK0
(Page 46)
ARAGON-MCK
R909 0 DOUT1
C619 R656
47 3.3k
IC914 IC615
PCM5101 PCM1754DBQR
C624 C630
IC914 IC615 100p 100p
G C922 D/A CONVERTER 33 D/A CONVERTER 35
0.1 1.7 1.7 R629 R643
R795 10 IC604 0 0
C998 0.1 3.4 3.4 C994 0.1 1 BCK SCK 16 PCM1754DBQR
1 CPVDD DVDD 20 R819
1.7
2 CAPP DGND 19 R796 10 1.7
2 DATA FMT 15
10
IC604
1.9
3 CPGND LDOO 18 C995 0.1 1.7 34 D/A CONVERTER
R797 10
C997 2.2 1.7
4 CAPM XSMT 17
3.4 3 LRCK MUTE 14 2.6
3.3 9 AGND VOUTR 8
C996 2.2 5 VNEG FMT 16 4 DGND DEMP 13 2.6 2.6
0
6 OUTL
50 LRCK 15
1.7
R762 10 10 VCOM VOUTL 7
C742 C744 C609
0 5 NC TEST 12
H 7 OUTR DIN 14
1.7
R761 10 10 16V 0.1 10 16V 11 ZEROA VCC 6
5.1
>022S 22
AVDD+3.3V 3.4
8 AVDD
49 BCK 13
1.7
R760 10 5.1
6 VCC ZEROA 11
1.7
C748 C617
C696 C699 9 AGND SCK 12 R817 10 2.6 10 16V 12 TEST NC 5 0.1 C622
MOTHERBOARD 2.6
BOARD
10 16V 0.1 48 0 R978 0 7 VOUTL VCOM 10 10 16V
VCC5V
(7/10) 10 DEMP FLT 11 13 DEMP DGND 4 5 >005S
(Page 46) R793 25
0 8 VOUTR AGND 9 1.7 ARAGON-LRCK0 MOTHERBOARD
R630 10
14 MUTE LRCK 3 BOARD
(1/10)
1.7 R631 10 R948 0 DOUT2 (Page 40)
R747 R763 15 FMT DATA 2
0 0 C984 R820 24
10 10 1.7 1.7 R632 10 ARAGON-BCK0
I C983
10
C982
10 26
16 SCK BCK 1
R831
R829 R826 100
470 470
C689 2200p C692 2200p
R830 10k R827 10k C749
10 16V
C690 C704
10 16V 10 16V DOUT0
11 >011S
FRONT-R
FRONT-L
MOTHERBOARD
BOARD
(9/10)
SW
(Page 48)
>023S 23
MOTHERBOARD
K BOARD
(10/10)
(Page 49)
HCD-GT3D
42 42
HCD-GT3D
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
B 11 >011S
MOTHERBOARD
BOARD
(9/10)
(Page 48)
>003S 3
R791 0 DIN3
MOTHERBOARD
BOARD
(1/10)
(Page 40)
C C640 4.7 R
MOTHERBOARD
BOARD
IC912 (1/10)
TC74VHC157FT (EK) (Page 40)
C648 4.7 L D+3.3V
IC912 1 >001S
SIGNAL SELECTOR
R661 R674 C977
100 100 ANALOG-DSEL/SD_D1_0 R801 3.4 3.4 0.1
100
1 SELECT VCC 16
JL134 R702 0 DGND
10
2 1A ST 15 4 >004S
R701 10 0
3 1B
47 4A 14
1.7 R835 10
C642 R677 0 0
MOTHERBOARD
R802 1.7
D AGND
10p
R687 22
22
4 1Y 46
45
4B 13
1.7
R836
R837
10
22 R980 0 ARAGON-BCK3
BOARD
(1/10)
(Page 40)
>010S 10 R690 10 5 2A 4Y 12
C644 1.7 R838 10
MOTHERBOARD 10p 6 2B 44 3A 11
BOARD 1.7 R839 10
(7/10) 7 2Y 3B 10
(Page 46) 2.5 2.5 3.4 1.5 1.7
8 GND
43 3Y 9
1.7 R840 22 R981 0 ARAGON-LRCK3
14 13 12 11 10 9 8
29
42
VINR
VINL
FMT
MD1
MD0
DOUT
BCK
IC606
PCM1808PWR
E IC606
DGND
AGND
VREF
LRCK
SCKI
VCC
VDD
A/D CONVERTER
MTK LACK
DIR DATA
DIR LACK
MTK BCK
DIR BCK
1 2 3 4 5 6 7
2.6 5.1 3.4 1.7 1.7
C649 C653 12 >012S

10 16V
1000p 0.1
27 28 MOTHERBOARD
0.1
IC913
TC7WH157FK BOARD
(2/10)
C655 IC913 (Page 41)
C645
C646
10 SIGNAL SELECTOR
F VCC5V R963 10 1.5
1 A VCC 8
3.4
>005S 5
C989
MOTHERBOARD R964 10 0 0.1
BOARD 2 B _ST 7
(1/10)
(Page 40) R688 R691 3.4 R965 100 ANALOG-CSEL
10 10 3 _Y SEL 6
0 PCONT-DAMP
4 GND Y 5
C664
0.22
>024S 24
MTK-MCK
G MOTHERBOARD
BOARD
ADIN
M+13V
13 >013S
(5/10) MTK-LRCK MTK LACK MOTHERBOARD
(Page 44) BOARD
MTK-BCK MTK BCK (2/10), (7/10)
ASDATA0 R966 10
DVDD5V
>019S 19
JL005 A+13V
MOTHERBOARD
BOARD
26 >026S
H (2/10), (5/10)
JL904 VIDEO-MUTE MOTHERBOARD
BOARD
(7/10)
C011 C010 CN001 (Page 46)
IC901 0.1 100p 9P
NJM41031F1(TE2)
1 13.5V
IC901 JL007
2 AGND
VIDEO AMP JL008
3 13.5V
3.14 5.1 R080 0
1 POWER SAVE V+ 6 C024 C092 C091 JL053 4 13.5V
C904 C905 R036 0
470 25V 0.1 100p JL057 SMPS
1.2 0.1 100 10V JL006 5 M/DGND
2 VOUT GND 5 BOARD
R935 C928 R086 6 M/DGND ~AC IN
I J907 JL631
75 1000 6.3V 1.2
3 VSAG VIN 4
2.1 JL905 0 JL045 7 AC-DET
(1/2)
1P C906 R905 JL004

1 0 8 MAIN ON
VIDEO OUT JL906
JL068 9 LOW_AC
C1003
0.001
JL907
C076
0.01 AC_DET
29 >029S
J JL056 MOTHERBOARD
BOARD
(8/10)
(Page 47)
CVBUS
>025S 25
MOTHERBOARD
BOARD MGND
(5/10) 15 >015S
(Page 44)
MOTHERBOARD
BOARD
(7/10)
(Page 46)
K
HCD-GT3D
43 43
HCD-GT3D
Ver. 1.2
6-10. SCHEMATIC DIAGRAM - MOTHERBOARD Board (5/10) - • See page 37 for Waveforms. • See page 59 for IC Block Diagrams. • See page 66 for IC Pin Function Descriptions.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
MOTHERBOARD BOARD (5/10) CVBUS

25 >025S
A MOTHERBOARD
BOARD
(4/10)
>024S 24 (Page 43)
MOTHERBOARD
ASDATA0
MTK-LRCK
MTK-BCK
MTK-MCK
MTK-P108
MTK-P107
ADIN
FE_OP-
FE_OPO
BOARD
(4/10), (6/10), MOTHERBOARD
OPDIST R349 100 BOARD
(9/10), (10/10)
(Page 43), (Page 45), C334 0.01 R351 10k (1/10)
(Page 48), (Page 49) (Page 40)
DGND
4 >004S
10k
0.01
RFIP
1
C356
B 1
150
560
100
0.1
C355
C353
10
R372
10
0
1
3.3 DVDD3.3V
CL316
CL320
CL321
C343 1 4 NC CE 3 17 >017S
C341
R358
C340 1
C337
R390
R368
R370
C345
GND 2 MOTHERBOARD
CL335 3.4 5.1 BOARD
C339 0.01 R371 0
5 VOUT VDD 1 (2/10), (6/10)
CL308 C338 0.1 (Page 41), (Page 45)
330
100
47
IC305
CL329
CL330
CL331
CL332
CL333
CL334
FE_VOC
CL318
CL314
CL319
CL310
CL312
BU33TD3WG-TR
FE_VOB
R360
R365
R367
JL339
IC305 DVDD5V
19 >019S
>027S 27 C328 10 2.1 2.1 2.6 2.6 3.4 0.9 1.3 3.4 3.4 0 1.7 1.7 1.7 1.7 3.4 0.2 1.3 1.3 3.4 0.4 1.3 0 +3.3V REG
MOTHERBOARD
C MOTHERBOARD
BOARD C316 10 C330 0.1 128 127 126 125 124 123 122 121 120 119 118 117 116 115 114 113 112 111 110 109 108 107 106 105 104 103 102 101 100 99 98 97 BOARD
(2/10), (4/10)
C350
RF_B
ADACVDD1
RF_A
SPFG/OP-
IOPMON/OPO
OPDIST
RFIP
ADACVDD2
AGND12
AVDD12_1
ASDATA0
ALRCK
NC
AVCM
NC
ABCK
ACLK
ADACVSS1
ADACVSS2
AADVDD
NC
NC
ADIN
AADVSS
CR/R
SC/CB/B
SY/Y/G
DACVDDB
CVBS
DACVSSC
FS
VREF
(6/10) (Page 41), (Page 43)
(Page 45) 47 10V
VC
FE_VOA 2 3.4 C352 0.1
1 RF_C DACVDDC 96
FE_VOD 2
2 RF_D MFIDET 95 CL336
FE_3.3V R322 0 CL307 FE_VOF 0.2
23 22 21 20 CL337 RB303
>028S 28 3 RF_E XMAMUTE 94 22
FE_VOE 0.2
MOTHERBOARD 4 RF_F SPDIF 93 CL338
BOARD C331 R328 12 1.2 1.6 RA3 IC306
5 AVDD12_2 RA3 92 EM638165TSD-6G
(6/10) 0.1 3.4 2.5 RA2
R326 0
D (Page 45)
C322 10p 0.8
6 AVDD33_1 RA2 91
2.5 RA1 IC306
7 XTALI 18 RA1 90 SDRAM
R334 0.7 0.3 RA0
X301 100k 8 XTALO RA0 89
27MHz
9 AGND33
19 RA10 88
0 RA10 28 VSS VDD 27
3.4 C364 0.1
C319 10 C323 12p R332 330
2 1.3 C346 0.01 BA1 1.1
10 V20 DVDD12 87 RA4 1.1 RA3
1.4 1.5 BA0 29 A4 A3 26
11 V14/VREF0 BA1 86 1.6
FE_VREFO 0 0.9 RA5 1.1 RA2
R330 15k 12 REXT RB305 30 A5 A2 25
BA0 85
PD 0 3.4 C347 0.01 22 1.7
13 MDI1 DVDD33 84 RA6 1.1 RA1
3.3 31 A6 A1 24
FE_CD_LDD 3.3 RAS
E FE_DVD_LDD 3.3
14 LDO1 IC301
CXD9990R
RAS# 83
3.2 CAS RA7 1.2
32 A7 A0 23
0.2 RA0
15 LDO2 CAS# 82
3.3
16 AVDD33_2
IC301 DVSS12 81
RWE
RA8 0 0 RA10
CD RF AMP FOCUS/TRACKING ERROR AMP, 33 A8 A10/AP 22
FE_DMO 1.4 3.3 RB304
17 DMO CD SYSTEM PROCESSOR, RWE# 80 22 RB302 0
FE_FMO 1.4 1.1 22 RA4 RA9 1.3 BA1
18 FMO DIGITAL SERVO PROCESSOR RA4 79 34 A9 BA1 21
CD_VR 0 1.6 RA5 0 1.2 BA0
19 CD_VR RA5 78 RA11 35 A11 BA0 20
DVD_VR 0 1.7 RA6 C359 0.01
20 DVD_VR RA6 77 0
FE_TRO 1.4 1.2 RB301 R382 10k
21 TRO RA7 76 36 NC CS 19
22
FE_FOO 1.4 0 RA7 3.3
F MSW 0.1
22 FOO RA8 75
0 RA8
37 CLKE RAS 18
3.3 RAS
23 MSW RA9 74 1.5 3.2
USBM JL330 R335 0 0 0 RA9 CAS
24 USB_DM RA11 73 38 CLK CAS 17
USBP JL331 R337 0 0 1.5 RA11 3 3.3 RWE
25 USB_DP RCLK 72 39 UDQM WE 16
FE_MUTE 3.4 3.4 C348 0.01
26 VDD33_USB R380 100
DVDD33 71 3
3 R379 22 R381 DQM0
27 VSS33_USB DQM1 70 10k 40 NC LDQM 15
IC303 R339 5.1k 0.8 1.2 RD8 3.4
BD00IC0WHFV-GTR 28 PAD_VRT RD8 69 C360 0.1
1.3 1 RB306 41 VSS VDD 14
RD9
IC303 3.4
29 VDD12_USB RD9 68
1.1 RD10 RD8
22 0.8
42 DQ8 DQ7 13
1.1 RD7
G +1.2V REG
R327 47 0
30 SF_CS#
31 SF_DO
RD10 67
1.3 RD11 RD9 3.4
RD6
3.4 RD11 66 43 VDDQ VSSQ 12
JL354
4 EN GND 3 R302 0.3 1.4 RD10 RD5

C373 0.8 27k 32 SF_DI RD12 65 0.7 0.2
1000p 5 NC FB 2 RD11 RD4
LIMITSW
44 DQ9 DQ6 11
DVDD33
DVDD12
DVSS33
MFISW
SF_CK
PRST#
3.1
IFSDO
0.3
IFSCK
EEWP
IFBSY
DQM0
IFCS#
MUTE
IFSDI
RD15
RD14
RD13
6 VCC VO 1 RB308
SDA
RD0
RD1
RD2
RD3
RD4
RD5
RD6
RD7
SCL
0.7 0.3
NC
NC
RX
TX
R378 45 DQ10 DQ5 10 22

JL355 R331 R340
47 47 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 0 3.3 C365 0.1
46 VSSQ VDDQ 9
0.1
10
R303 C321 10 1.4 3.3 0.1 3.4 3.4 3.4 3.3 2 3.2 3.1 2.8 0 3.4 3.4 3.4 3.4 0.8 0.7 0.6 0.6 1.3 0.5 0.3 0.2 1.3 3 1.2 1.6 1.6
R369 22 DQM0
47k 0.7 0.5
C315 0.1
CL309
CL311
CL313
CL315
CL317
CL322
47 DQ11 DQ4 8
C372
C369
RB307
H C326 0.01
C325 0.01 RD12
22 0.7
48 DQ12 DQ3 7
0.5 RD3
L301 C336 0.01 RD2
47nH RD13 3.4
0.01
0.01
1k
R348 4.7k 49 VDDQ VSSQ 6

0
0
0
RD1
RD14
R387 3.3k 0.9 0.6 RD0
RD15 50 DQ13 DQ2 5
R359
R363
R364
R366
R357 3.3k
C344
C342
RD0
RD1
RD2
RD3
RD4
RD5
RD6
RD7
R361 4.7k 0.9 0.6 RB309

51 DQ14 DQ1 4 22
R321 100
3.3 C363 0.1
52 VSSQ VDDQ 3
100
10k
47
RXD R347 0
0
0
TXD R350 0 0.4 0.8

I R329 0
53 DQ15 DQ0 2
R352
R354
R355
R356
R362
100
100
C349 0.01
47
3.4 C362 10
R319 54 VSS VDD 1
0.5 3.3 10k
1 CS VCC 8
R342
R344
R345
1.3 3.3
2 SO/SIO1 HOLD/SIO3 7 IC304 R373 C357 0.1
0 FL301 FB321
C324 0.1 3.3 1.4 R1EX24016ASAS0A FB320
3 WP/SIO2 SCLK 6 R346 3.3k 0uH 0uH
C358 0.1
4 GND SI/SIO0 5
0 R343 3.3k IC304 1
3
2
JL341
4.7k
4.7k
IC302
10k
EEPROM
JL332
JL333
JL335
JL334
JL336
JL337
JL338
MX25L3235EM2I-10G
IC302 1 A0 VCC 8
3.3
R374
R376
R377
J SERIAL FLASH 0
2 A1 WE 7
3.3
MTK_RESET 3 A2 SCL 6
3.3
4 GND SDA 5
C354
XSYSRST
0.1
FE_LIMIT
XIFBSY
IFSDO
IFSCK
XIFCS
IFSDI
Note : IC301, IC302 and IC303 on the MOTHERBOARD

board cannot exchange with single. When these
parts on the MOTHERBOARD board are damaged,
exchange the entire mounted board.
HCD-GT3D
44 44
HCD-GT3D
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
FE_5V R386 0
>020S 20
MOTHERBOARD
BOARD R500 0 FE_LD_DVD
(2/10)
(Page 41) R471 0 FE_LD_CD
CN302
24P FE_3.3V
GND (LD) 1
JL301 28 >028S
JL302 C366 0.01 FE_VREFO
LD (650) 2 MOTHERBOARD
FE_MUTE BOARD
JL303 R318 10k R310 (5/10)
NC 3 SL301
4.7k OPDIST (Page 44)
C 5V 4
JL304
JL305 PD FE_FMO
PD 5 SL401 R433
JL306 C367 0.01 FE_TRO 0 FE_3.3V_1
LD (780) 6 SL402 18 >018S
JL307 R389 100 DVD_VR FE_FOO SL403
VR (650) 7 MOTHERBOARD
IC401 BOARD
JL308 R301 100 CD_VR FE_DMO SL404 AM5890S
VR (780) 8 (2/10)
NC 9
JL309
C402
IC401 (Page 41)
JL310 FE_VOE 330p FOCUS/TRACKING COIL DRIVE,

VOE/E+G 10 C302 0.1 SPINDLE/SLED/LOADING MOTOR DRIVE C411
JL311 R402 R411 330p
VCC 11
JL312 C303 0.1 27k 1.4 0 10k
D SERVICE,
VC 12
JL313 C403
1 VINFC MUTE 28
1.4 C407 0.1
OPTICAL DEVICE(7G) GND (PDIC) 13 0.015 CL401 2 TRB_1 BIAS 27 R415
JL314 FE_VOF 1.4 27k
(1/2) VOF/F+H 14 R401 R408 CL402 3 REGO2 VINTK 26
JL315 FE_VOB 10k 10k 1.4
VOB/B 15 4 VINSL+ TRB_2 25 CL408
MOTHERBOARD
JL316 FE_VOA C413
VOA/A 16 CL403 5 REGO1 RESET 24 CL409 0.1 R418 BOARD
JL317 RFIP FWD R406 0 CL404 0 1.4 15k (1/10)
RF 17 6 FWD VINLD 23 (Page 40)
REV R407 0 CL405 0 DGND
JL318 MSW
MSW 18 7 REV GND 22 4 >004S
JL319 FE_VOD C409 0.1
VOD/D 19
JL320 FE_VOC
E VOD/C 20
JL321 FE_TRK- C401 C404
29 PGND PGND 30
CN401
TRK- 21 100 10V 0.1 JL401
JL322 FE_TRK+ SL405 6P
TRK+ 22 C418 6 SL+
5.4 1.5
JL323 FE_FCS+ 8 VCC1 CL410 SL406 JL402 0.1
FCS+ 23 VCTL 21 5 SL-
LOAD- 0 0 CL411
JL324 FE_FCS- 9 VOTR- VCCD 20 JL403
FCS- 24 4 NC(LIMIT)
LOAD+ 0 5.4 SERVICE,
10 VOTR+ VCC2 19 JL404
3 NC(GND) OPTICAL DEVICE(7G)
VC 2.6 2.6
11 VOSL+ VOLD- 18 SL407 JL405 (2/2)
2.6
2 SP+
2.6 C419
12 VOSL- VOLD+ 17 SL408
0.1 1 SP-
FE_FCS- 2.7 2.6
>027S 27 13 VOFC- VOTK- 16 JL406
F MOTHERBOARD
FE_FCS+ 2.7
14 VOFC+ VOTK+ 15
2.6 C408
0.1
BOARD
(5/10)
(Page 44) 16 >016S
FE_5.2V_M
MOTHERBOARD
C412 BOARD
100 10V (2/10)
FE_5.2V_TRAY (Page 41)
>011S 11
MOTHERBOARD FE_TRK-
BOARD
(9/10) MGND
G (Page 48)
FE_TRK+ 15 >015S
MOTHERBOARD
BOARD
R316 1k UNLOAD_END_SW (7/10)
R409 (Page 46)
C307 0.001 FE_OP- CL406 10k
R317 1k LOAD_END_SW
D401 C405
CN303 RB520S-30FJTE61 0.1
5P R312 R313 R404
JL325 C308 0.001 1k 1k D402 C406 R410 1
TRAY-OUT 5 FE_OPO RB520S-30FJTE61 0.1 10k
JL326 C309 0.001
GND 4 CL407
JL327 FE_LIMIT
H MS-476 BOARD TRAY-IN 3
LOAD+ 2
JL328 LOAD+
JL329 C311 CL412 CL413
LOAD- 1 0.1
C310 0.001 LOAD-
15
15
15
15
15
15
R423
R425
R426
R427
R428
R430
R496 2.2k R463 2.7k R422 C420 C423 R431
MOTHERBOARD 47k 47 35V CL414 CL415 47 35V 47K
BOARD
(2/10), (5/10)
(Page 41), (Page 44) 3.3
R421 3.4
DVDD3.3V
I >017S 17 FE_DVD_LDD 100 3.3 3.3
R388 Q401 Q402

100k 2SA2119K 0 0 2SA2119K
AUTOMATIC POWER AUTOMATIC POWER
C421 CONTROL (FOR DVD) CONTROL (FOR CD) C424 R432
MTK-P108 0.01 0.01 100
JL352
MTK-P107
JL353
MTK_RESET R424 R429
JL346 100K 100k
MTK-POWER-CTRL
JL347
TXD FE_CD_LDD
J JL348
JL349 RXD
JL350 FE_LD_CD
JL351 FE_LD_DVD
E+3.3V
>030S 30
MOTHERBOARD
BOARD 24 >024S
K (7/10)
BOARD
(5/10)
(Page 44)
Note : When the MS-476 board is defective, exchange the

entire LOADING COMPLETE ASSY (T).
HCD-GT3D
45 45
HCD-GT3D
6-12. SCHEMATIC DIAGRAM - MOTHERBOARD Board (7/10) - • See page 37 for Waveforms.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
A
L004
2.2uH R087 0 C039 0.1
C014 C021 IC002
0.1 10
B TPS542941PWPR
IC002
DC-DC CONVERTER
13.7 13.7 C032 10
16 VIN2 VIN1 1
JC005 0 L002 C018 0.1 9.2
15 VBST2
4 VBST1 2
7 C034 0.1 L007 JC007 0
2.2uH 3.4 2.2uH
E+3.3V JL040 JC006 0 3 1.2 JC008 0 E+1.18V
>030S 30 14 SW2 SW1 3 34 >034S
JL041
MOTHERBOARD 13 PGND2 PGND1 4 MOTHERBOARD
BOARD 13.7 13.7 BOARD
(2/10), (6/10), 12 EN2 EN1 5 (9/10)
C (8/10), (9/10),
(10/10) 0.9
11 PG2 PG1 6
0.9
(Page 48)
(Page 41), (Page 45), R003 33k R041 12k

(Page 47), (Page 48), 10 VFB2 VFB1 7
C078 22p 5.8 C077 22p
(Page 49) 9 VREG5 GND 8
22
22
22k
22
22
R006 C036
C050
C053
10k 1
C004
C006
R043
DGND
4 >004S
MOTHERBOARD
D BOARD
(1/10)
(Page 40)
L003
M+13V 2.2uH C013 0.1
>013S 13
MOTHERBOARD IC001
BOARD TPS542941PWPR L008
(2/10), (4/10) 2.2uH
(Page 41), (Page 43) IC001
E DC-DC CONVERTER
13.7 13.7
1 VIN1 VIN2 16
JC001 0 C019 C017 0.1 10.4
2 VBST1
1 VBST2 15
9.2 C079 0.1 C030 C040 L006 JC003 0
10 5.1 3.4 10 0.1 4.7uH
USB+5V JL001 JC002 0 2 JC004 0 M+5.2V
>032S 32 3 SW1 SW2 14
E
31 >031S
L001 JL003
MOTHERBOARD 4.7uH 4 PGND1 PGND2 13 MOTHERBOARD
BOARD 3.4 13.7 BOARD
(10/10) 5 EN1 EN2 12 (2/10), (10/10)
(Page 49) (Page 41), (Page 49)
R059 6 PG1 PG2 11 R024 R023
68k 1 0.9 2.2k 56k
F 7 VFB1 VFB2 10
5.8
8 GND VREG5 9
22
22
C080 C081
22p 22p
22
22
R002 C035 R031
C049
C052
12k R020 1 10k
0
C003
C005
MGND
15 >015S
MOTHERBOARD
BOARD
(2/10), (4/10),
PCONT-BTSTBY
(6/10), (10/10)
(Page 41), (Page 43),
G (Page 45), (Page 49)
VBUS-OE
>011S 11
MOTHERBOARD
BOARD
(9/10)
(Page 48)
AVDD+9V
9 >009S
H MOTHERBOARD
BOARD
(1/10)
(Page 40)
A+13V_GV2
>033S 33
MOTHERBOARD AVDD+5V
BOARD 21 >021S
(10/10)
BOARD
IC004 IC006 (2/10), (3/10)
78D09AG-TN3-R 78D05AG-TN3-R (Page 41), (Page 42)
I Q004
KTA1542T-RTK/P
IC004 IC006
+13V PWR SUPPLY +9V REG +5V REG
A+13V 13.7 13.6 13.6 9.1 JL047 9.1 5.1 JL048
>026S 26
JL046
VIN VOUT
GND
VIN VOUT
GND
MOTHERBOARD 3.4 5.1
BOARD
R029
68k 12.9 3 4
(4/10)
(Page 43) JL026
VOUT
VDD
R033 R035
3.3k 3.3k
JL067 AVDD+3.3V
22 >022S
100 16V
100 10V
0.1
J MOTHERBOARD
0.1
0.1
0.1
47
PCONT-PSAVE-PROTECT 3.3
BOARD
1
C051 (3/10)
Q461 0.1 (Page 42)
KRC402-RTK
C085
C057
C062
R085
C068
C072
C100
GND
PWR SUPPLY
CE
CONTROL
2 1
5.1
AGND C101 1
>010S 10
MOTHERBOARD IC008
BOARD MM3411A33URE
K (1/10), (2/10),
(3/10), (4/10), IC008
(10/10), +3.3V REG
(Page 40), (Page 41),
(Page 42), (Page 43),
(Page 49)
Note : IC001 and IC002 on the MOTHERBOARD board

cannot exchange with single. When these parts on
the MOTHERBOARD board are damaged, exchange
the entire mounted board.
HCD-GT3D
46 46
HCD-GT3D
Ver. 1.1
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17

11 >011S
MOTHERBOARD
B BOARD
(9/10)
(Page 48)
R125 47k R131 100
R123 10k USBDPVCC

35 >035S
R120 47k MOTHERBOARD
BOARD
(9/10)
C 3.4
3.4
14 VCC 1G 1
3.4
R140
(Page 48)
3.4
13 4G 1A 2 22k
3.4 3.4
R116 47k IC102 R132 47
12 4A 1Y 3
3.4 TC74VHC126FT (EK) 3.4 DEBUG-RXD(MD-BOOT1)
JL149 R127 10k JL196
11 4Y 2G 4
3.4
10 3G
IC102 2A 5
3.4 SS-DET(MD-CLKS) TEST-MON0/SD_D2_0
JL197
3.4 BUS BUFFER 3.4 AC-CUT(MD-BOOT0)
R129 100 R133 47 BT-RXD(MD-CLK) JL198
9 3A 2Y 6
3.4
R134 47 DEBUG-RXD(MD-BOOT1) TEST-MON1/SD_D3_0
8 3Y GND 7 JL199
R135 47 AC-CUT(MD-BOOT0) FL-LCD-CLK
C109 JL200
C106
D C102
0.1 0.1
1
R137 R139 R143
TEST-MON2/SD_CMD_0
PCONT-BTSTBY
JL201
22k 22k 22k JL215
AC_DET C284 0.1 C167 0.1
JL195
>029S 29
R115 JL216
MOTHERBOARD
BOARD 1k TEST-MON3/SD_CLK
JL269 JL202
(4/10)
(Page 43) JL217
R117 D102 R128 TEST-MON4/SD_D0_0
DA2J10100L 1k JL203
6.8k 1.2 3.4 LCD-CSB
3.4 R099 3 CT VDD 2 R126 JL235
0 0 ANALOG-DSEL/SD_D1_0
E Q107
KRC402-RTK
0.1 3.4
4 VOUT GND 1 JL148
JL150 RESET
RGB-TRANS-LED/SD_CD_0
JL204
AC OFF DETECT JL205
RGB-TRANS-LED-SPK/SD_WP_0
IC103 JL206
BU4229F-TR
C103 C104 C105 IC103 C107 C110

0.1 0.0022 RESET 0.1 0.1
4.7 35V
E+3.3V
30 >030S
MOTHERBOARD
BOARD
(7/10)
F CN105
(Page 46)
R122 6P
0 JL151
1 VDD
NFC_CLK JL152
2 SCL
JL194
3 DGND NFC MODULE
CN101 NFC_DATA JL153 (RC-S730 (WW))
5P 4 DATA
NFC-IRQ JL154
GND 1 5 IRQ
NFC-RF-DET JL155
MCU VCC 2 6 RF-DET
FOR JL110 DEBUG-TXD
G SERVICE USE TXD1 3
RXD1 4
JL111
R191
100
CLK1 5 JL103
JL169
DIR_CP-CLK JL131 JL170
R206 R204 R202 R194 JL171
10k 10k 10k 10k
TCK
JL172
DGND TMS
JL173
>004S 4 TDI
JL174
H MOTHERBOARD
BOARD
IC105
MFI337S3959
TDO
JL175
(1/10)
(Page 40) IC105 TRST
JL176
COPROCESSOR
3.4
1 GND VCC 8 36 >036S
DIR_CP-DATA 3.4 0
2 SDA RST 7 JL227 MOTHERBOARD
JL132 JL224 3.4 BOARD
3 NC_3 SCL 6 (9/10)
(Page 48)
4 NC_4 NC_5 5 JL228 R161 C166 C165 CN102
JL225 10k 0.1 0.1 10P
I JL112
JL113
1 GND
2 GND
JL104
3 GPIO
BT-RXD JL105
D+3.3V 4 BT-RXD
>001S 1 BT-TXD JL106
5 BT-TXD BLUETOOTH
MOTHERBOARD JL107 MODULE
BOARD 6 BT-CTS
(1/10) JL108
(Page 40) Q103 7 BT-RTS
KTA1542T-RTK/P JL114
8 3.3V
BT-RESET +3.3V PWR SUPPLY JL109
J 3.4 3.4
JL115
9 BT-RESET
10 GND
R108
10k
2.7
Q104
KRC402-RTK R109
PWR SUPPLY 2.2k
0
CONTROL
BT-ON 3.3
Note : IC105 on the MOTHERBOARD board cannot

exchange with single. When this part on the
MOTHERBOARD board is damaged, exchange the
entire mounted board.
HCD-GT3D
47 47
HCD-GT3D
Ver. 1.1
6-14. SCHEMATIC DIAGRAM - MOTHERBOARD Board (9/10) - • See page 37 for Waveforms. • See page 59 for IC Block Diagrams. • See page 66 for IC Pin Function Descriptions.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
DOUT0
ARAGON-LRCK0
ARAGON-BCK0
DIN3
MTK-POWER-CTRL
JOG+
DEBUG-TXD
ANALOG-BSEL
ANALOG-ASEL
FL-SOUT_LCD-SDA
LCD-CSB
DOUT2
C-CONT
ARAGON-LRCK3
ARAGON-BCK3
BT-RESET
LOAD_END_SW
UNLOAD_END_SW
NFC-IRQ
OSC
BT-ON
VIDEO-MUTE
LCD-BCKLED
FL-LCD-CLK
ARAGON-MCK
A
MOTHERBOARD
IFSDI
IFSDO
XIFCS
XIFBSY
XSYSRST
IFSCK
BOARD
(7/10)
(Page 46)
>024S 24 R113 0 E+3.3V
MOTHERBOARD
30 >030S
BOARD R299 C139 R114 0 E+1.18V
(5/10) 10k
34 >034S
(Page 44) 47p MOTHERBOARD
0uH
0uH
100
100
100
100
100
47p
100p
0.01
100
100
100
100
100
100
100
100
100
100
100
100
100
100
10k
10k
10k
10k
10k
10k
10k
100
47p
100
100
100
47p
10k
10k
BOARD
47
47
0
0
0
0
0
(7/10)
B (Page 46)
C299
R198
R251
R257
R261
R265
R267
R581
R263
R119
R226
C142
R219
R254
R242
R229
R230
R232
R582
R274
R237
R283
C143
C295
R150
R193
R580
R579
R201
R295
R210
R211
R213
R215
R273
R218
FB116
FB115
R259
R256
R587
R216
R221
C141
R224
R284
C133 0.1
C137 0.1
100k
100k
JL193
JL298
JL294
JL278
JL209
JL211
JL212
C146 0.1 C164
JL292
JL281
JL282
JL179
JL222
JL182
JL183
JL185
JL187
JL189
JL190
C162 0.01 0.1 R111
100k
0 3.4
C150 100 10V R288 47
R110
R294
1 CS VCC 8
0 0
R289 47 R291 47
2 SO/SIO1 HOLD/SIO3 7
C148 0.1 0 0
R290 47 R292 47
C140 0.1 3 WP/SIO2 SCLK 6
0 R293 47
C C135 0.1
3.4 3.4 3.4 3.4 0 3.4 3.4 0.1
44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9
0 1.2 1.7 1.7 1.7 1.7 0 3.4 1.7 3.4 1.7 3.3 1.2 0.2 3.2 3.3 2 3.4 1.8 3.4 3.4 3.4 1.7
8
3.4 1.2 3.4 3.4 0.4 0.4 3.4 3.4
7 6 5 4 3 2 1
4 GND SI/SIO0 5
C161 0.01
IC106
JOG+
DEBUG-TXD
ANALOG-BSEL
ANALOG-ASEL
LCD-SDA / FL-SOUT
PVCC
LCD-CSB / TEST-MON38
CKIO
VSS
LCD-CLK / FL-CLK
VCC
SSI2_DO
SSI0_DO
VSS
SSI0_LRCKO
SSI0_BCKO
SSI3_DI
C-CONT
SSI3_LRCKO
PVCC
SSI3_BCKO
VSS
MTK-SDO
VCC
MTK-SDI
MTK-XIFCS
VSS
MTK-CLK
MTK-BUSY
MTK-RESET
MTK-POWER-CTRL
AUDIO_CLK_OUT
NFC-INT
PVCC
OSC
VSS
BT-ON
VCC
LOW_AC_SUPPLY_DET / LCD_BCKLED
BT-RESET
CDM-LOAD-SW
CDM-UNLOAD-SW
VIDEO-MUTE
SRC-RST0
R112 100k MX25L3235EM2I-10G
C149 100 10V
R286 100k
C168 0.1
R287 100k
IC106
R300 10k SERIAL FLASH
POWER-KEY R181 100 3.4
45 POWER-KEY 9 8 7 6 5 LINK-OUT-A 176
3.4 R270 100 LINK-OUT-A
JL162 0 R271 100 LINK-SET
46 VSS LINK-SET 175
USB-OC R163 0 3.4 3.4
JL163 47 USB-OC PVCC 174
RGB-SOUT 0 3.4 MIC-DET
C296 0.01 R164 100 R272 100
D JOG-
48 RGB-SOUT
JL293 3.4 49 JOG-
MIC-DETECT 173
0
R183 10k
R247 100 Q-FLASH-SIO1 172
R268 10k 3.4
C111 0.1 R575 100 DIR_RESET
50 PVCC VSS 171
LINK-OUT-B R197 100 0 3.4
R222 10k 51 LINK-OUT-B Q-FLASH-SIO0 170
VBUS-OE R255 100 JL210 3.4 52 VBUS-OE Q-FLASH-CS 169
0
R588 10k
NFC-RF-DET R168 100 JL297 3.4 53 NFC-RF-DET Q-FLASH-CLK 168
0
DOUT1 R169 47 JL161 1.7 54 SSI1_DO Q-FLASH-SIO3 167

0
DIN1 R170 47 JL164 1.2 55 SSI1_DI Q-FLASH-SIO2 166

0
/SD-FAST R234 100 JL288 3.4 56 3.4 JL299

E PCONT-PSAVE-PROTECT
R589 10k
R172 100 3.4
SD-FAST
57 PCONT-PSAVE-PROTECT
SS-DET/3D-DETECT/DIR-RESET
ANALOG-CSEL
165
164
3.4 JL300 R590 0 ANALOG-CSEL
R107 10k 1.2
R103 10k 58 VCC VSS 163
LINK-DET C112 0.1 3.4
R173 100 59 LINK-DET
C113 0.1 VSS 162
USB_HOST_SEL R576 100 0
60 USB_HOST_SEL USBUVSS 161
JL285 1.2 C154 0.1
61 VSS USBUVCC 160
C114 0.1 3.4
62 PVCC USBAVSS 159
AC-CUT(MD-BOOT0) 3.4 1.2 C155 0.1
JL268 63 AC-CUT(MD-BOOT0) USBAVCC 158
DEBUG-RXD(MD-BOOT1) 3.4 3.4
64 DEBUG-RXD(MD-BOOT1) IC101 USBAPVCC 157
F BT-RXD(MD-CLK) 3.4
65 BT-RXD(MD-CLK) R7S7200032CFP-A USBAPVSS 156 C298
1
SS-DET(MD-CLKS) R102 100
C278
3.4
66 MD-CLKS IC101 REFRIN 155
0 R285 5.6k
1.1
22p
X101 67 RTC-X1 10 SYSTEM CONTROLLER
USBDVSS 154
1.6 1.2 C157 0.1 C297
32.768kHz 68 RTC-X2 USBDVCC 153 0.1
C279 22p R185 0
1.2
69 PLLVCC
11 VBUSIN0 152
5.2 USBA+5V
C126 1.7 0 JL295 R585 0 USB_DP0
10p X102 R188 1.7
70 EXTAL 12 DP0 151
0 R586 0 USB_DM0
13.333MHz 1M 71 XTAL DM0 150
C127 10p R186 72 VSS
13 USBDPVSS 149
JL296
G C115 0.1
0
73 VSS USBDPVCC 148
3.4 USBDPVCC
35 >035S
R175 10k 3.4
74 NMI USBDVSS 147 MOTHERBOARD
R149 1.2 C159 0.1 BOARD
10k 75 VSS USBDVCC 146 (8/10)
RESET C118 0.1 R176 100 3.4 (Page 47)
76 RES VBUSIN1 145
3.4
77 PVCC DP1 144
R104 C116 0.1
4.7k /AMP-PROTECT R153 100 JL160 3.4
C117 4.7 78 AMP-PROTECT DM1 143
SPM-C-MON R154 100 JL159 3.4 79 SPM-C-MON
C280 0.1 USBDPVSS 142
11 >011S
SPM-AMBINET-TEMP JL158 1.7 3.4 R275 C151
R155 100 80 470 6p
C282 0.1 SPM-AMBIENT-TEMP USBDPVCC 141
MOTHERBOARD
H C281 0.1
R156 100 JL255 1.7 81 MODEL-DEST-IN 17 USB-X2 140
1.7
R269 X104
BOARD
(1/10), (2/10),
FAN_DET R177 100 JL165 1.3 82 1.7
1M 48MHz C152 (3/10), (4/10),
C120 0.1 FAN_DET USB-X1 139
MASTER-VOLUME R157 1k R178 100 JL256 3.4
83 MASTER-VOLUME
LCD-INHB(LCD_BCKLED) / FL-LATCH 16 VSS 138
7p (6/10), (7/10),
(8/10), (10/10),
R160 C121 0.01
JL167 3.4 84 JL214 R276 (Page 40), (Page 41),
3D-RESET_ANALOG-DSEL/SD_D1_0
4.7k AD-KEY0 R158 470 R179 100 BT-TXD 0 100 RGB-SCLK
C122 0.1 AD-KEY0 RGB-SCLK 137 (Page 42), (Page 43),
FB117 0
AD-KEY1 R159 470 R180 100 JL168 3.4 85 AD-KEY1 0 (Page 45), (Page 46),
C123 0.1 DIR_INT1/AMP-CLK-FR 136 (Page 47), (Page 49)
EVOL_CLK/RELAY CONTROL
3.4 3.3 SIRCS
JL213 R278 100
86 AVCC SIRCS 135
C128 10
TEST-MON2/SD_CMD_0
3.4 R279 100 FL-LAT_LCD-INHB
DIR_INT0/EVOL_DATA
87 AVSS
TEST-MON0/SD_D2_0
TEST-MON1/SD_D3_0
TEST-MON4/SD_D0_0
134
TEST_MON3/SD_CLK
3.4 3.4 R280 100 BT-TXD

C158 0.1
88 AVREF 14 15 133
PCONT-BTSTBY
C160 0.1 FB101 C129 0.1

I
RGB-PWM-CLK
PCONT-DAMP
DIR_CP-DATA
0uH
/AMP-RESET
CD-MOTOR+
DIR_CP-CLK
C134 0.1
CD-MOTOR-
/LINE-MUTE
NFC_DATA
AUDIO-X1
AUDIO-X2
NFC_CLK
ST-DATA
BSCANP
C136 0.1
ST-RDS
ST-CLK
R572 100 DIR_INT1
ST-CE
PVCC
PVCC
PVCC
TRST
C144 0.1
VCC
TDO
TMS
VCC
VCC
VSS
TCK
VSS
VSS
VSS
VSS
TDI
C156 0.1
C153 0.1 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132
0 3.4 1.7 1.7 3.4 1.2 3.4 0 0.2 3.4 3.4 3.4 0 0 1.2 0 0 3.4 0 3.4 0 0 3.4 3.4 3.3 1.7 1.2 3.3 0 3.4 0 3.4 3.4 3.4 3.4 0 3.4 3.4 3.4
C131 0.1 DGND
4 >004S
100 JL207
100 JL208
100 JL271
JL272
100 JL273
100 JL274
100 JL275
100 JL276
JL178
JL283
JL289
C138 0.1
R196 1M MOTHERBOARD
JL184
JL186
JL188
JL166
JL191
100 JL116
C147 0.1 R146 10k BOARD

100
100
100
100
100
100
100
100
100
47
R144 15k R200 (1/10)

10k
100
100
J 0 (Page 40)
47
R145 15k X103

47
47
47
47
12.288MHz
R241
R243
R245
R248
R252
R105
R297
R189
R174
R574
R223
R225
R228
10k R166
R233
R236
R238
R106
R203
R171
TRST
100k
C130
TDO
TMS
R227
TCK
TDI
R220
10p
4.7k
4.7k
4.7k
4.7k
4.7k
4.7k
4.7k
10k
R212
R214
R217
R100
C132
R190
10p
R282
R298
R244
R246
R250
R253
R195
R192
R167
>036S 36
K EVOL_CLK/RELAY CONTROL
MOTHERBOARD
ANALOG-DSEL/SD_D1_0
TEST-MON2/SD_CMD_0
BOARD
DIR_INT0/EVOL_DATA
TEST-MON0/SD_D2_0
TEST-MON1/SD_D3_0
TEST-MON4/SD_D0_0
(8/10)
TEST-MON3/SD_CLK
(Page 47)
PCONT-BTSTBY
RGB-PWM-CLK
PCONT-DAMP
DIR_CP-DATA
/AMP-RESET
DIR_CP-CLK
/LINE-MUTE
Note : IC101, IC106 on the MOTHERBOARD board cannot

NFC_DATA
NFC_CLK
ST-DATA
ST-RDS
ST-CLK
ST-CE
exchange with single. When these part on the

FWD
REV
MOTHERBOARD board are damaged, exchange the

entire mounted board.
HCD-GT3D
48 48
HCD-GT3D
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17

11 >011S
MOTHERBOARD
BOARD
(9/10)
RGB-PWM-CLK (Page 48)
R543 100
C526 0.01
C532 CN517
47 16V 4P
4 3.3 R564 22 JL518
JL525 R503 33 4 M+5.2V
13 /OUT8 /OUT7 12
B R504 33 4
4
14 /OUT9 /OUT6 11
3.3
3.3
R555 22 3 RED_HLED
>040S
R506 33 R552 22 JL528
15 /OUT10 /OUT5 10 2 GREEN_HLED
4 3.3 SPK_HLED
R507 33 R549 22 C527 0.01
16 /OUT11 /OUT4 9 R538 1 BLUE_HLED BOARD
3.3 R510 22 C528 0.01 0 CN4000
17 /OUT12 /OUT3 8 (Page 56)
3.3 R514 22 AGND
18 /OUT13 /OUT2 7
JL529 10 >010S
R264 0 JL522 R567 33 4 3.3 R511 22 MOTHERBOARD
19 /OUT14 /OUT1 6 BOARD
R260 0 R566 22 3 3.3
JL523 R515 22 (7/10)
20 /OUT15 /OUT0 5
1.7 0 RGB-TRANS-LED-SPK/SD_WP_0 (Page 46)
R569 100
0.01
0.01
21 PWMCLK TRANS 4
C 1.1
22 SOUT SCK 3
0 R542 100 RGB-SCLK
R534 680 0 R541 100 RGB-SOUT
C541
C530
23 REXT SIN 2
MGND C511 0.1 3.4
IC502
>015S 15 24 VDD GND 1
TC62D723FNG
MOTHERBOARD 25
BOARD IC502
(7/10) LED DRIVER
(Page 46) 23 >023S
E+3.3V MOTHERBOARD
>030S 30
BOARD
MOTHERBOARD (3/10)
CN119 (Page 42)
D BOARD
(7/10) CN118
19P
(Page 46) 25P 1 AGND
JL129
NC 1 2 AGND
LED+5.2V 2 JL259
3 AGND
JL130 SW JL239
LED+5.2V 3 4 SW
JL133
LED_GND 4 5 AGND
LED_GND 5 FRONT-R JL240 6 FR
JL136 FL-LCD-CLK
LCD_SCL 6 7 AGND
JL137 FL-SOUT_LCD-SDA FRONT-L JL241
LCD_SDA 7
E LCD_INHB 8 JL138 FL-LAT_LCD-INHB
8 FL
9 AGND
JL139 LCD-CSB /SD-FAST JL242
LCD_CSB 9 10 /SD-FAST >041S
JL140 AD-KEY0 /AMP-RESET JL270
AD-KEY0 10 11 /AMP-RESET DAMP
JL141 AD-KEY1 /AMP-PROTECT JL244 BOARD
AD-KEY1 11 12 /DAMP-PROTECT (2/2)
JL142 CN1001
DGND 12 13 M+5V
JL143 JL247 (Page 52)
>039S E+3.3V 13 14 MGND
JL144 SIRCS
SPLITTER SIRCS 14 15 MGND
BOARD JL145 POWER-KEY JL248
CN3400 POWER KEY 15 16 M+13V
F (Page 58)
VOL 16
JL146 MASTER-VOLUME JL249
17 A+13V
JL147 FAN-DET JL251
D+3.3V 17 18 FAN-DET
JL290 EVOL-CLK/RELAY CONTROL JL252
RGB_SD 18 19 RELAY CONTROL
JL230
RGB_PWM 19
JL231 RGB-TRANS-LED/SD_CD_0 R142
RGB_TRANS 20 0 A+13V_GV2
RGB_SCLK 21
JL232 33 >033S
JL286 LCD-BCKLED MOTHERBOARD
LCD_BCK_LED 22 BOARD
JL287 JOG+ (7/10)
JOG_POS 23 (Page 46)
G JOG_NEG 24
JL291 JOG-
JL284 OSC
OSC 25 M+5.2V
31 >031S
MOTHERBOARD
BOARD
(2/10), (7/10)
D+3.3V R478 0
>001S 1 SW+13V
USBA+5V
14 >014S
H MOTHERBOARD
BOARD MOTHERBOARD
(1/10) BOARD
(Page 40) (2/10)
USB_DP0 (Page 41)
USBP R466 0 R470 0
R559
10k 1 NC1 NC_14 14 C468
USB_HOST_SEL 0 3.4 0.1
R480 0
2 S VCC 13
I USBM R467 0 R472 0 0
3 1D-
IC453
TC7USB40FT OE 12
JL469
USB_DM0 0 0
C467 CN451
0
4 2D-
IC453 1D+ 11
0 0.1 JL456
8P
5 D- USB SWITCH 2D+ 10 8 USB_B GND
USB-OC JL455 C465 0.1 0 JL457
6 GND D+ 9 7 D+B
C464 JL458
7 NC_7 NC_8 8 6 D-B
0.1
JL459
5 USBB+5V
>024S 24 JL460 >042S
4 USB_A GND
MOTHERBOARD JL461 MIC
BOARD 3 D+A BOARD
CN3201
J (5/10)
(Page 44)
JL462
JL463
2 D-A (Page 57)
R465 100 1 USBA+5V

R464 FB455
33k 0uH
DGND 0 R583 0.1
>004S 4 1 V- 2+IN 5
0
IC452 JL454 R577 470 USB+5V
MOTHERBOARD
NJM2903CV (TE1)
2 1+IN 2-IN 6 32 >032S
BOARD 0 C466 0.1
3 1-IN 2OUT 7 MOTHERBOARD
(1/10)
(Page 40) IC452 4 1OUT V+ 8
0 R498 0.1 BOARD
(7/10)
USB COMPARATOR (Page 46)
K C462 10 16V
C463 0.1
HCD-GT3D
49 49
HCD-GT3D
Ver. 1.1
6-16. PRINTED WIRING BOARD - DAMP Board - • See page 32 for Circuit Boards Location. • : Uses unleaded solder.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
A
DAMP BOARD
(COMPONENT SIDE)
MID/TWEETERS
IM3ED$NCE8SE2ȍ
LOUDSPEAKER
L R
B WHITE RED
+ -
DAMP BOARD
-
+ – + –
(CONDUCTOR SIDE)
R1033
R1062
Q1014 Q1016
B B R1091 Q1010
C1063
R1032 B
E E R1092
RY001 C CL1054
TB001 R1112
C Q1015 Q1017
B B
R1063 E
CL1051
R1031
R1130 CL1049 CL1048
C1125
E
B C1003 D1007 CL1062
E E CL1050 CL1061
R1131 Q1023
R1170 R1171
R1133
D1013
Q1021
E
B R1132
C1137
C1122
C1168
R1072
C1081
C1082
C1123
R1029
Q1003 C1059
C1108
C1121
C1167
CN1007 E C1080 R1106
R1111
C1056
C1062
C1124
2 B
C1055 C1132
R1135
C1077
C1052
E CL1046 CL1047
D1008
C1131
D C1083
R1037
R1134
(CHASSIS) C1169 (CHASSIS)
R1161
R1160
R1162
B
R1024
R1026
C1078
C1051
Q1004 Q1006
R1028
C1076
C1079 CL1052
C1044
C1046
B
R1030
C1002
R1022 C1048 C1047
R1036
E
R1065
R1067
R1139
R1137
R1138 R1064
R1136
R1025 C1053 C1054
R1070
C1001
R1020 C1043
R1021 C1045
C1067 CL1053
R1080
R1069
R1066
C1005
R1068
C1068
R1078
B
Q1011
C1049
E
C1075
R1085 R1083
R1027
C1074
E
C1050
R1084
C1057
L1007
R1023
R1082
C1004
C1058
C1141 C1139
R1079
C1138
R1077
L1006
C1142
CL1027
CL1030
F C1140
DC FAN
C1128
C1127
CN1004
R1081
1
2 M
CL1002
L1010
R1076
C1107
C1105
C1129
CL1032
C1126
C1029 C1026
G C1036 C1022
L1009
C1060 CL1059
CL1031
C1061
CL1026 CL1028
C1091
R1088 C1106
R1087 C1104
1
48 33
49 32
C1092
C1095
C1133
C1021
C1038 C1037
H R1017 IC1001 8 5
C1020
R1012 IC1003
1 4
CL1005
R1011
C1015
CN1005
(CHASSIS) (CHASSIS)
CL1037
CL1024
CL1025
C1039
R1018 C1090
R1053
C1040
R1052 CL1023
64 17 CL1038
D1016
1 16
C1007
R1009
CL1045 CL1043
R1127
R1129
CL1021
CL1044 CL1006
C1011 C1012 CL1041
R1141
CL1022 R1035 C1089 CL1007

9
D1002 CL1008
CL1042
I JC1019 CL1009
C1134
R1001
R1008
C1008
E B D1017 JC1020 CL1004 CL1013 CL1014

C1136
R1002
D1006
Q1018 CL1017
R1126 R1128
D1005 CL1012 CL1010

B
D1001 R1003 2 18
CN1001 CL1003
R1148
R1157
C1118 1 19 CL1039 CL1015

E
C1120 C1119 C1117 CL1001
Q1019 R1004 R1005 CL1063
R1154
5 4 CL1019
R1167
R1169
C1151
R1152
CL1060
R1155 C1155 R1156
IC1005
C1147
IC10044 R1163
R1158
CL1018 CL1011
C1143
5 CL1016
R1149 C1148
R1159
8 1
C1144
J
R1150
R1168
R1153
C1156 R1145
R1151
R1164
8 1 B
D1014
R1147
C1150
R1165
(CHASSIS) E
R1166 C1149 Q1022
(CHASSIS)
12 12
>004P
K MOTHERBOARD
BOARD 1-894-011- (12) 1-894-011- (12)
~ AC IN SMPS BOARD >006P CN119
(Page 39)
MOTHERBOARD
BOARD
CN001
(Page 39)
Note 1: When the complete DAMP board is replaced, refer to “NOTE Note 2: When the C1126, C1127, C1128, C1129, C1142, L1010 and RY001
OF REPLACING THE IC1001 ON THE DAMP BOARD AND on the DAMP board are replaced, spread the bond referring to “BOND
THE COMPLETE DAMP BOARD” on servicing notes (page 5). FIXATION OF ELECTRIC PARTS” on servicing notes (page 6).
HCD-GT3D
50 50
HCD-GT3D
Ver. 1.1
6-17. SCHEMATIC DIAGRAM - DAMP Board (1/2) - • See page 59 for IC Block Diagrams.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
A DAMP BOARD (1/2)

/AMP-RESET
Q1019 CN1005
Q1018 8P
KTA1542T-RTK/P PBSS4160T
AMP RESET SWITCH AMP RESET SWITCH 3.1 1 V1
3.3 0 0
R1128 4.7k
CL1031
3 V1
R1129
L1010 4 V1
B 33k 3.3 C1136
47 16V
R1126
100k C1142 20uH
5 V1 SMPS
C1134 R1127 3300 71V
BOARD
0.1 12k 6 V1_GND
CL1032
7 V1_GND
8 V1_GND
R1160 R1161 R1162 9 V1_GND
CL1023 0 0 0
R1018 R1017
3.3 3.3
C C1040 0.1
330p
0.1
0.1
C1036 CN1007
C1095 2.2 2P
0.1 R1020 R1021 C1076 0.1 CL1046
CL1061 1 SW - -
C1038
C1037
3.3
C1039
3.3 C1077 0.01 CL1047 LOUDSPEAKER
CL1028 2 SW + +
R1001 22k CL1022 C1074 C1043 C1045 C1078 0.01
12.4 2 12.4 12.4 30.2 24.2 24.2 50.8 50.8 1 0.0022 0.022
C1007 220p CL1045 C1079 0.1
CL1026
64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 L1006 C1044 C1046
D1001 ~ D1002 R1137
0.0022 0 0.022
VDD
PSU_REF
NC_62
NC_61
NC_60
NC_59
GND_58
GND_57
GVDD_B
GVDD_A
BST_A
OUT_A_53
OUT_A_52
PVDD_A_51
PVDD_A_50
GND_A_49
BAV99-215 10uH
D D1001 D1002
1 OC_ADJ 48
R1008 100 1.2 C1049 R1136
CL1059
2 RESET 47 C1047
0.022 0
C1120 C1008 1000p CL1021 3.1 GND_A_48 0.0022
R1002 3 C_STARTUP GND_B_46 46 C1029 D1017 R1171
1 100 24.2 2.2 RB551V-30TE-17
SW+ 3.3 GND_B_47 C1075 C1050 C1048 1k
4 INPUT_A OUT_B_45 45 1 0.022
2 24.2 0.0022
SW-
5 INPUT_B OUT_B_44 44 R1170
C1119 R1003 2 50.8 R1023 R1022 1k
100 6 VI_CM PVDD_B_43 43 3.3 3.3 C1080 0.1
1 C1011 1000p 2 50.8
7 GND_7 IC1001 PVDD_B_42 42 C1061 C1059 0.01
C1012 0.1 TAS5630BPHDR 30.4 0.1
8 AGND BST_B 41
E C1117 R1004 9 VREG IC1001 BST_C 40
30.2
CL1049 TB001
1 100 3.3 POWER AMP 50.8
FL C1060 C1026 4P RED
10 INPUT_C PVDD_C_39 39 0.1
2 50.8 2.2 R1025 R1024 RY001 CL1050 +
FR R1088 C1106 - R
11 INPUT_D PVDD_C_38 38 3.3 3.3 CL1062 MID/TWEETERS
C1118 R1005 R1141 10k R1009 10k 2 24.2 3.3 0.0022
12 FREQ_ADJ GND_C_34 OUT_C_37 37 + ,03('$1&(86(ȍ
1 100 Q1021 D1013 C1081 0.01 CL1051
1 24.2 C1053 C1051 - L
GND_D_33 C1126 R1081 LSCR523UBFS8TL DA2J10100L WHITE
C1140
CL1044 13 OSC_IO+ OUT_C_36 36 C1107 0.022 0.0022
47
47
220
0.1
10k 0.0022 C1082 0.1
CL1042
1.8
14 OSC_IO- GND_C_35 35 35V R1132 RELAY DRIVER 0.1
C1054 C1052 1k 0.8
CL1041 1.4
15 SD 34 0.022 0.0022
R1130
R1131
PVDD_D_30
PVDD_D_31
R1035 3.4
GND_D_32
C1127
OUT_D_28
OUT_D_29
C1141
1k CL1043 16 OTW1 33 R1077 R1080 C1068 R1133 C1137
GVDD_C
GVDD_D
0.1
GND_23
GND_24
220 10k 10k 1 47k 100 10V

READY
3.3
F
BST_D
OTW2
35V
CLIP
D1005 D1006 CL1048

M1
M2
M3
17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 R1085 R1083 R1135

47k 100k 0
D1005 ~ D1006 3.3 3.3 12.4 12.4 30.2 24.2 24.2 50.8 50.8 C1124 0.01
BAV99-215
L1007 C1121 0.1
CL1030 10uH
CL1037
CL1024
CL1025
C1167 0.1
R1134 0
C1168 0.1
0.1
0.1
C1021 CL1027 C1057 C1055
1
0.1 C1022 0.022 0.0022 C1123 0.01
G 2.2 R1082 R1084
C1067
C1015
C1020
100k 47k C1058 C1056 C1122 0.1

0.022 0.0022
C1131 0.1
R1078 R1027 R1026
C1104 C1105 C1138 3.3 C1132 0.015
/SD-FAST R1011 R1012 0.0022 0.0022 0.1 10k 3.3
3.3 3.3 C1169 0.1
GVDD C1128
R1079 220
10k
35V
R1087
3.3
C1139 R1076 C1129
220
H 0.1 10k
35V R1028
680k
R1030
680k
R1032
56k
R1106
56k
R1112
56k
R1111
56k
Q1014 ~ Q1017
2SA1162-G R1029 R1033 R1031
OVERLOAD DETECTION 680k 220k 220k
Q1003 ~ Q1004 C1062 C1063 C1125

Q1004 Q1016 Q1014
2SA1162-G 47 24.6 0 47 25.3 0 47 25.3 0
OVERLOAD DETECTION
24.6 25.3 25.3

I Q1003 Q1017 Q1015
24.6 0 25.3 0 25.3 0
24.6 25.3 25.3
DAMP-PROTECT R1138 18k

3.4 R1037
Q1006 0 680
LSCR523UBFS8TL
DC DETECTION C1108 1 50V R1072 1k
J R1036
100k
C1083
47 35V
D1008
M+13V BAV99-215
MGND
K
1 2 3
>043S >044S >045S
DAMP BOARD DAMP BOARD DAMP BOARD

3DJH 3DJH 3DJH
Note 1: When the complete DAMP board is replaced, refer to “NOTE Note 2: When the C1126, C1127, C1128, C1129, C1142, L1010 and RY001
OF REPLACING THE IC1001 ON THE DAMP BOARD AND on the DAMP board are replaced, spread the bond referring to “BOND
THE COMPLETE DAMP BOARD” on servicing notes (page 5). FIXATION OF ELECTRIC PARTS” on servicing notes (page 6).
HCD-GT3D
51 51
HCD-GT3D
6-18. SCHEMATIC DIAGRAM - DAMP Board (2/2) -
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
>044S
DAMP BOARD
(1/2)
(Page 51)
2
B
DAMP BOARD (2/2)
C D1007
RB551V-30TE-17
CN1004
2P
13.7 5.1 CL1052
1 FAN+
R1062
Q1010
DSA700300L
CL1053
2 FAN-
M DC FAN
10k 13.7 FAN MOTOR
DRIVER
R1139
C1003 R1063 R1091 R1092 0
10 3.3k 3.3k 3.3k
D
CL1054 R1070 R1064
0 27k C1001 22k
0.1 3.4
0
C1004 Q1011 0.1
R1065 R1067
10 50V LSCR523UBFS8TL 2.2 2.2
Q1023 FAN PROTECTION
LSCR523UBFS8TL
>045S 3 FAN RESET R1069 C1002 C1005 R1066 R1068
SWITCH 22k 0.1 22 3.3 2.2
DAMP BOARD
(1/2)
(Page 51)
E
CN1001
19P
RELAY_CTRL 1 CL1001
CL1002
FAN-DET 2
CL1003
A+13V 3
CL1004 M+13V
F M+13V 4
MGND 5
CL1005
CL1006 MGND
MGND 6
CL1007
M+5V 7
CL1008 /DAMP-PROTECT IC1005
/DAMP-PROTECT 8 IC1004 NJM4565M(TE2)
CL1009 /AMP-RESET NJM4565M(TE2) R1168 3.9k
/AMP-RESET 9
CL1010 /SD-FAST
C1149
0.1 IC1004
R1167 3.3k IC1005
>041S /SD-FAST 10
PRE AMP
PRE AMP C1156 R1154
CL1011 R1148 1.8k
MOTHERBOARD AGND 11 R1151 C1148 R1150 1.8k 6.5 0.0027
0.0022 2.2k R1157 2.2k R1156 2.2k
BOARD CL1012 R1153 1.8k 2.2k 6.5 5 2+IN GND 4
FL 12 5 2+IN GND 4 6.5 6.5
G (10/10)
CN119
AGND 13
CL1013 C1150 C1151 6.5
6 2-IN 1+IN 3
6.5
6.7
6 2-IN 1+IN 3
6.5
C1155
0.0022
(Page 49) 1500p 0.0022 C1147 7 2OUT
CL1014 6.5 6.5 1-IN 2
FR 14 7 2OUT 1-IN 2 1500p R1159 12.4 6.3
R1155 5.6k
CL1015 R1169 3.3k 12.4 6.5 R1158 4.7k 8 VCC 1OUT 1
AGND 15 8 VCC 1OUT 1 4.7k R1166
CL1016 R1152 R1164 R1165 R1149 3.3k
SW 16 8.2k 4.7k
CL1017 C1144 100 10V 8.2k 4.7k
AGND 17
CL1063
AGND 18 CL1018
AGND 19 CL1019 Q1022
LSCR523UBFS8TL
BIAS 12.5
H R1147 100k 6.5
C1143 0.1 7.1

R1145 2.2k
JC1019 JC1020
0 0 D1014 IC1003
DZ2J068M0L BD00GA3WEFJ-E2
R1163 0
CL1060
IC1003
13.6 +12V REG
CL1039
5 EN NC_4 4
C1092 1000p
I L1009
6 NC_6 GND 3
0.8
R1052
47k
47uH 7 NC_7 FB 2
13.4 12.2 CL1038
8 VCC VO 1
R1053 C1089 C1090

C1091 C1133 3.3k 10 0.1
10 50V 50V
0.1
GVDD
SW+
D1016
SW-
FR
FL
RF05VAM2STR
J 1 >043S
DAMP BOARD
(1/2)
(Page 51)
HCD-GT3D
52 52
HCD-GT3D
6-19. PRINTED WIRING BOARD - BUTTON Board - • See page 32 for Circuit Boards Location. • : Uses unleaded solder.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
S3108 S3107
SOUND FIELD FUNCTION
CL3126
B
JR3104
R3137 R3136
JR
CL3125
S3123 S3113
MIC BOARD
CN3202 REC TO USB PARTY CHAIN
(Page 56) CL3131
>008P CL3141
R3150 R3141
BUTTON BOARD
C
EN3100
S3110 MULTI
DJ EFFECT CONTROL
ISOLATOR R3123
C3107
4 3 1 S3111 S3112 S3109
DJ EFFECT DJ EFFECT DJ EFFECT
CN3101 SAMPLER
DJ OFF FLANGER
R3139 R3138
C3111
CL3113 R3140
CL3115 CL3114 R3124
CL3129 CL3127
D CL3130 CL3128
RV3100
R3125
MIC LEVEL CL3116
C3113
E
S3122 S3121
MIC ECHO VOCAL FADER
CL3140 S3106 S3105
R3149
R3148 ENTER LIGHT MODE

CL3139
F CL3124 CL3123
R3135 S3103
R3132
CL3138 R3134 - PAIRING
R3133 BLUETOOTH
R3147
S3119 S3104
JR3101
JR3100
D3100
D3105
S1
JR
CL3137 MEGA BASS
JR
C3117
R3146 -
CL3107 EN3101
CL3109
S3120 VOLUME/
R3129
G S2
+ CL3110
CL3118 DJ CONTROL CL3122 CL3102
JR3103
CL3121
JR
CL3117
>009P
JR
SPLITTER BOARD CL3100 CL3101 JR3102
CN3402
(Page 58)
S3118 CL3108 CL3132
S4 2 10
TUNING + CL3103 S3102 S3101
CN3100 1 11
H N x
R3131
>
CL3120 CL3119
CL3105
R3130
CL3136
R3144
S3117 R3143
R3145
CL3135 S3
TUNING - CL3134 R3142 CL3133
.
S3116 S3115
FOOTBALL PARTY LIGHT
I
CL3104
J
S3114
Z CL3106
S3100
"/1
K
12
1-894-298- (12)
HCD-GT3D
53 53
HCD-GT3D
Ver. 1.2
6-20. SCHEMATIC DIAGRAM - BUTTON Board -
1 2 3 4 5 6 7 8 9 10 11
BUTTON BOARD
A S3114
Z
S3101
x
CL3132
CL3119 S3115
S3102 PARTY LIGHT R3142
680
R3130 N
CN3100 680
11P D3105 D3100 CL3133
B LED+5.2V 11
CL3101 HL-364B460MZ-T
BT LED
HL-364V620MZ-T
BASS BAZUCA LED CL3120
S3116
FOOTBALL
CL3102 R3143
LED+5.2V 10 S3103 1k
AD-KEY0 9 CL3103 R3131 - PAIRING
CL3104 1k BLUETOOTH CL3134
AD-KEY1 8 S3117
DGND 7 CL3105
S3
CL3106 CL3107 CL3121 TUNING - R3144
>047S POWER-KEY 6 S3104
.
CL3107 S3100 R3132 MEGA BASS 1.5k
SPLITTER VOL 5
BOARD CL3108 "/1 1.5k
CN3402 BLUE_LED 4 CL3135
C (Page 58)
RED_LED 3
R3124 0
CL3109 CL3122
S3105
S3118
JOG_POS 2 CL3100 S4
R3133 LIGHT MODE TUNING +
CL3110 R3123 0 1.5k R3145
JOG_NEG 1 > 1.5k
CL3118 CL3123
CL3136
0.01
S3106
S3119
C3107 R3134 ENTER
0.01 C3117 R3129 2.2k S1
C3111
0.001 10k - R3146

2.2k
CL3124
S3107
D EN3100 EN3101
VOLUME / R3135 FUNCTION S3120
CL3137
MULTI CONTROL
DJ CONTROL 3.3k S2
+ R3147
CL3125 3.3k
S3108
C3113 RV3100 R3136 SOUND FIELD CL3138
2.2 50V 50k 4.7k
CL3116 MIC LEVEL S3121
CN3101 CL3126 VOCAL FADER R3148
4P R3125 S3109 S3111 4.7k
CL3113 10k DJ EFFECT DJ EFFECT
AMP_+IN1 1
E R3137
6.8k FLANGER DJ OFF CL3139
>048S CL3114 S3122
AMP_OUT2 3 CL3127 CL3129 R3149
MIC MIC ECHO 6.8k
BOARD CL3115
MIC_GND 4 S3110 S3112
CN3202
(Page 57) DJ EFFECT DJ EFFECT
R3138 ISOLATOR SAMPLER CL3140
R3139 S3113 S3123
10k 22k
PARTY CHAIN REC TO USB
CL3128 CL3130 R3150
R3140 15k 10k
CL3131 CL3141
F R3141 15k
HCD-GT3D
54 54
HCD-GT3D
Ver. 1.1
6-21. PRINTED WIRING BOARD - LCD Board - 6-23. PRINTED WIRING BOARD - OPTICAL Board -
• See page 32 for Circuit Boards Location. • : Uses unleaded solder. • See page 32 for Circuit Boards Location. • : Uses unleaded solder.
1 2 3 4 5 6 7 8 1 2 3 4 5 6
LCD BOARD
OPTICAL IN
OPTICAL BOARD TV
A A
CL3062
CL3059
CL3056
CL3048
CL3047
CL3046
CL3045
CL3041
CL3039
CL3037
CL3036
CL3031
CL3029
ND3000
IC3300
IC3000
CL3027
CL3060
CL3075
CL3073
CL3071
CL3067
CL3025
CL3069
CL3026
CL3043
CL3028
Q3000
CL3074
CL3038
CL3040
CL3072
CL3035
CL3070
CL3053
CL3064
LP3300
CL3068
3 2 1
D3001
CL3030
CL3050
B 27 26
R3004
R3003
E
C3002
CL3065
CL3044
CL3063 3 2 1
R3301
R3033
R3300
R3034
C3000
CL3057
39 14
IC3004 C3012 CL3302
R3011
40 13 R3030
C3011
B B C3303
R3002
CL3000 CL3061 C3001

CL3005 CL3054 R3028
CL3022 R3000
52 1
CL3049 R3026 CL3006 R3001
CL3004 C3301
4
R3035
JR3000
CL3051
CN3300
CL3001 JR
CL3023
CL3042 CL3301
3
C3008
CL3032
CL3034
C3010
CL3024
CL3033
C3009
>001P
JR3300
CL3002
R3025
>010P
JR
CL3003 CL3008
R3022
MOTHERBOARD
SPLITTER BOARD BOARD
1
CN3401 CN602
(Page 58) (Page 39)
CN3000 CL3300
2 12
C 1 13 C
CL3009 CL3007 12 12
(12)
1-894-297- (12) 1-894-300-
6-22. SCHEMATIC DIAGRAM - LCD Board - • See page 59 for IC Block Diagrams. 6-24. SCHEMATIC DIAGRAM - OPTICAL Board -
1 2 3 4 5 6 7 8 1 2 3 4 5
ND3000
LCD BOARD LIQUID CRYSTAL DISPLAY
A A OPTICAL BOARD
LP3300
IC3300
JSR1124
CN3300
4P R3301 0
IC3300
DIGITAL OPTICAL
GND 1 RECEIVER
CL3300
COM0 CL3023
COM1 CL3024
COM2 CL3025
COM3 CL3026
SEG0 CL3027
CL3028
CL3029
CL3030
CL3031
CL3035
CL3036
CL3037
CL3038
CL3039
SEG10 CL3040
SEG11 CL3041
SEG12 CL3043
SEG13 CL3045
SEG14 CL3046
SEG15 CL3047
SEG16 CL3048
SEG17 CL3050
SEG18 CL3053
SEG19 CL3056
SEG20 CL3059
SEG21 CL3062
SEG22 CL3064
SEG23 CL3067
SEG24 CL3068
SEG25 CL3069
SEG26 CL3070
SEG27 CL3071
SEG28 CL3072
SEG29 CL3073
SEG30 CL3074
SEG31 CL3075
1 VOUT
>038S CL3301 OPTICAL IN
VOUT 3 2 GND
B B MOTHERBOARD
BOARD VCC 4 C3301 C3303 3 VCC
TV
SEG1
SEG2
SEG3
SEG4
SEG5
SEG6
SEG7
SEG8
SEG9
(2/10) CL3302 0.22 0.22

CN602
(Page 41)
R3300
0
CL3060
CL3044
SEG23
SEG22
SEG20
SEG19
SEG18
SEG17
SEG16
SEG15
SEG14
SEG13
150
330
470
SEG21
R3002
R3003
R3004
1.7 1.7 1.7 1.7 1.7 1.7 1.7 1.7 1.7 1.7 1.7
39 38 37 36 35 34 33 32 31 30 29 28 27
C D3001 C
SEG23
SEG22
NC_37
SEG21
SEG20
SEG19
SEG18
SEG17
SEG16
SEG15
NC_29
SEG14
SEG13
1L043RW32E0CIE11
BACKLIGHT LED
3.3
Q3000 0.2
LTC014EUBFS8TL 1.7
SEG24 SEG12
LED DRIVER C3002 40 SEG24 SEG12 26
1.7 1.7
CN3000 0.1 SEG25 SEG11
41 SEG25 SEG11 25
13P R3035 1.7 1.7
0 SEG26 SEG10
42 SEG26 SEG10 24
LED+5.2V 13 SEG27 1.7 1.7
SEG9
CL3022 43 SEG27 SEG9 23
LED+5.2V 12 SEG28 1.7 1.7
SEG8
44 SEG28 IC3004 SEG8 22
D LED_GND 11
CL3002
R3011
0 SEG29 1.7
45 SEG29 BU9795AKS2 SEG7 21
1.7
SEG7
LED_GND 10
LCD_SCL 9
CL3003 LCD_SCL
SEG30 1.7
46 SEG30 IC3004 SEG6 20
1.7
1.7
SEG6
SEG31 1.7 LIQUID CRYSTAL DISPLAY SEG5
CL3004 LCD_SDA 47 SEG31 SEG5 19
LCD_SDA 8 1.7 DRIVER 1.7
SEG4
CL3005 LCD_INHB CL3032 48 SEG32 SEG4 18
>046S LCD_INHB 7 1.7
SEG3
CL3006 LCD_CSB CL3033 49 SEG33 SEG3 17
SPLITTER LCD_CSB 6 1.7
SEG2
BOARD CL3034 50 SEG34 SEG2 16
CN3401 SIRCS 5 CL3007 COM0 1.7
SEG1
(Page 58) CL3008 E+3.3V 51 COM0 SEG1 15
E+3.3V 4 COM1 1.7 1.7
SEG0
CL3009 52 COM1 SEG0 14
E LCD_BCK_LED 3
CL3001 OSC
1.7
OSC 2
DGND CL3000 DGND
1
OSCIN
NC_11
COM2
COM3
VLCD
NC_3
TEST
INHB
VDD
CSB
SDA
VSS
SCL
C3000 0.001
1 2 3 4 5 6 7 8 9 10 11 12 13
R3000 100 3.3 1.7 1.7 3.4 1.7 3.4 0 0 0 0 3.4

1 VO
CL3042
R3033
CL3049
CL3051
CL3054
CL3057
CL3061
CL3063
COM2
COM3
2 GND 100
3.3
C3001 3 VCC
F 1
C3009
CL3065
R3001 47 0.1
C3008 0.1
IC3000
PNA4823M03S0 E+3.3V R3022 0
IC3000 LCD_INHB R3034 0
REMOTE CONTROL OSC R3025 0
SIGNAL RECEIVER LCD_CSB R3026 1k C3010 22p
LCD_SCL R3028 1k C3011 22p
LCD_SDA C3012 22p
G DGND
R3030 1k
HCD-GT3D
55 55
HCD-GT3D
Ver. 1.1
6-25. PRINTED WIRING BOARD - SPK_HLED Board - 6-27. PRINTED WIRING BOARD - MIC Board -
• See page 32 for Circuit Boards Location. • : Uses unleaded solder. • See page 32 for Circuit Boards Location. • : Uses unleaded solder.
1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8
SPK_HLED BOARD MIC BOARD MIC 2 MIC 1

REC/PLAY
A (COMPONENT SIDE) A J3201 J3200 5V 1A
D4001 D4002 D4000

1
D3207
CN3203
CN4000
>007P JR3206
C3236
CL3225
R3219
JR
C3237
MOTHERBOARD 1 4
C3231
B BOARD B D3209 D3208
4
CN517
(Page 39) R3221
C3207
R3230
R3231
C3232 C3216
CL3227 C3208
CL3221
JR3205
JR
C3230
12
JR
JR3204
R3210
R3220
CL3229
CL3226
(12) R3223 R3217 C3226
C3204
1-894-386-
CL3228
CL3224
C3227 R3218 C3235 JR
JR3200
CL3223
C3223
JR3208
C C JR C3234 C3229 R3222
SPK_HLED BOARD
8 5
CL3222 D3204 D3202
R3216
C3224
IC3200 JR JR3201
1 4
(CONDUCTOR SIDE)
D3206
D3205
C3201
C3202
R3215 CL3214 C3211
C3225
Q3201
C3206
C3217 R3211
C3222
R3212 G JR3203 JR3207 JR D3200
JR3202
R3206
Q3200 CL3211 S
JR
CL3213 R3203
JR
R3234
R3229
C3221
C3218 B
C3215 R3207
R3205
E
FB002
R3204 R3202 CL3212
D D
R3200
CL4000 C3203 C3210 CL3218 CL3206
R3213 CL3207
R3201
CL4001 CL3220
CL4002 CL3202 CL3200 CL3217 CL3204 CL3232
R3214
CL3210 4 3 1 CL3205
CL4003 CL3203
4 1
CN3200 CN3202 CL3219 1 3 6 CN3201
FB003
LP3200 D3201 CL3209
CL3201
12
E 12 E (12)
(12) >003P >008P >002P 1-894-299-
1-894-386- MOTHERBOARD
BOARD
BUTTON BOARD
CN3101
MOTHERBOARD
BOARD
CN601 (Page 53) CN451
(Page 39) (Page 39)
6-26. SCHEMATIC DIAGRAM - SPK_HLED Board -
1 2 3 4 5 6 7 8
SPK_HLED BOARD
CL4000
B
D4000 D4002 D4001
LA CN5M-GAHA-24-1 (R) LT CN5M-GAHB-25-1 (G) LD CN5M-4Q4R-35-1 (B)
RED HLED GREEN HLED BLUE HLED
CN4000
4P
M+5.2V 1
CL4001
RED_HLED 2
>040S CL4002
GREEN_HLED 3
MOTHERBOARD CL4003
C BOARD
(10/10)
BLUE_HLED 4
CN517
(Page 49)
HCD-GT3D
56 56
HCD-GT3D
Ver. 1.1
6-28. SCHEMATIC DIAGRAM - MIC Board -
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
MIC BOARD R3229 0

A
CN3201
CN3202 6P
R3213 CL3204
DZ2J068M0L
DZ2J068M0L
4P
100 16V
CL3218 0 1 VBUS
D3204
D3202
AMP_+IN1 1 D3200
0.01
DZ2J068M0L
10
R3214 D3206 D3205 CL3205
>048S CL3219 0 BAV99-215 BAV99-215 3 D-
AMP_OUT2 3 >042S
C3208
C3207
C3204
BUTTON
CL3206 4 D+
CL3220 MOTHERBOARD
BOARD MIC_GND 4 R3234 0 CL3207
CN3101 5 USB_GND BOARD
B (Page 54) CN3200 FB002
CL3221 R3210 0 CL3232
6 SHIELD_GND
(10/10)
CN451
4P 0uH (Page 49)
CL3200
A+9V 1
FB003 0uH
CL3201
MIC_GND 2
>037S CL3202 CN3203
MIC_SIGNAL 3 4P
MOTHERBOARD CL3203
BOARD MIC_DET 4 REC/PLAY
(1/10) D3201 R3230 0
CN601 DA2J10100L
(Page 40) CL3209 R3231 0
R3218 C3229
R3205 C3206 33k 0.001 5V 1A
100 2.2 50V 9.1
C CL3213
CL3217
4.6
1 OUT1 IC3200
BA4558F
VCC 8
4.6
R3200 C3203 R3204 C3215 R3212 2 -IN1 OUT2 7 LP3200
1M 0.047 100k 68p 100k 4.6
3 +IN1 IC3200 -IN2 6
4.6 R3217
33k
C3227
0.001
C3216 D3207
0.001 BAV99-215
4.5 MIC AMP 4.5
4 VEE +IN2 5 C3226
C3210 R3207 220p CL3223
0.1 50V 10k C3217
220p
CL3214
C3211 R3211 C3218 CL3227
0.1 50V 100k 680p C3223 0.1 CL3228 J3200
C3230 2.2 50V R3220 1k CL3226
D R3215 10k R3216 10k CL3224 MIC 1
C3201 0.1 50V C3222 220 10V CL3222

R3201 1M R3219 1k C3232 2.2 50V C3236
0.001
Q3200
LSAR523UBFS8TL C3221 0.1 C3224 0.1 D3208
GAIN CONTROL 4.6
R3222 C3235 BAV99-215
3.9 R3206 100k 0.001
3.3k
CL3210
0 CL3212 C3231 R3221
E R3202
Q3201
RHK005N03T146
0 2.2 50V 1k CL3229 J3201
470 GAIN CONTROL MIC 2
C3225 CL3225
100k
0.001
0 220 10V
CL3211 D3209
BAV99-215
C3234
R3223
R3203 C3202 C3237
220k 10 50V 0.001
HCD-GT3D
57 57
HCD-GT3D
Ver. 1.1
6-29. PRINTED WIRING BOARD - SPLITTER Board - 6-30. SCHEMATIC DIAGRAM - SPLITTER Board -
• See page 32 for Circuit Boards Location. • : Uses unleaded solder.
1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8
SPLITTER BOARD
A SPLITTER BOARD A
CN3401
(COMPONENT SIDE) 13P
13 LED+5.2V
12 LED+5.2V
11 LED_GND
R002 CN3400
25P 10 LED_GND
2 24 NC 25 R002 R001 9 LED_SCL
0 0
CN3400 R001
1 25 LED+5.2V 24 8 LCD_SDA
B R008 B >046S
R005
R004
LED+5.2V 23 7 LCD_INHB
R003 (CHASSIS) LED_GND 22 6 LCD_CSB LCD
BOARD
LED_GND 21 5 SIRCS CN3000
(Page 55)
LCD_SCL 20 4 E+3.3V
LCD_SDA 19 3 LCD_BCK_LED
13 1 11 1
CN3401 LCD_INHB 18 2 OSC
CN3402
12 2 R006 10 2
12 LCD_CSB 17
AD_KEY0 16
1 DGND
C R007
1-894-358- (12) C AD_KEY1 15
DGND 14 R006 R007 R003
0 0 0 CN3402
>039S E+3.3V 13 11P
JL3400
>005P >010P >009P MOTHERBOARD SIRCS 12 11 LED+5.2V
BOARD
MOTHERBOARD (CHASSIS) LCD BOARD BUTTON BOARD
(10/10) POWER_KEY 11 10 LED+5.2V
BOARD CN3000 CN3100
CN118
CN118 (Page 55) (Page 53)
(Page 49) VOL 10 9 AD-KEY0
(Page 39)
NC 9 8 AD-KEY1
BLUE_LED 8 7 DGND
D SPLITTER BOARD D RED_LED 7

NC 6
6 POWER-KEY
5 VOL
>047S
BUTTON
(CONDUCTOR SIDE) NC 5
LCD_BCK_LED 4
R004
R005
0
0
4 BLUE_LED
3 RED_LED
BOARD
CN3100
(Page 54)
JOG_POS 3 2 JOG_POS
JOG_NEG 2 1 JOG_NEG
R008 0
OSC 1
JL3401
E E
JL3400 JL3401
12
F 1-894-358- (12)
HCD-GT3D
58 58
HCD-GT3D
• IC Block Diagrams
IC1001 TAS5630BPHDR (DAMP BOARD (1/2))
PSU_REF
GVDD_B
GVDD_A
PVDD_A
PVDD_A
GND_A
OUT_A
OUT_A
BST_A
GND
GND
VDD
NC
NC
NC
NC
64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49
GVDD_A
BST_A
OUT_A
OUT_A
PVDD_A
PVDD_A
GND_A
GVDD_B
OC_ADJ 1
VREG
CLIP
READY
OTW1
OTW2
SD
POWER-UP
M1 UVP
PROTECTION & I/O LOGIC

RESET
M2
M3 TEMP GVDD_A GVDD_C
SENSE
GVDD_B GVDD_D
/RESET 2
OVER-LOAD CURRENT
CB3C
PROTECTION SENSE
STARTUP
C_STARTUP 3 CONTROL 4
PVDD_X
PPSC 4
OUT_X
4
GND_X
OSCILLATOR
GVDD_A
PWM
ACTIVITY BST_A
DETECTOR
4
PVDD_X
PSU_FF PVDD_A
GND
PWM TIMING OUT_A
CONTROL GATE-DRIVE
RECEIVER CONTROL
GND_A
48 GND_A
GVDD_B
-
ANALOG
+
INPUT_A 4 LOOP FILTER 47 GND_B
46 GND_B
+ PWM TIMING
CONTROL GATE-DRIVE 45 OUT_B
ANALOG - RECEIVER CONTROL
ANALOG COMPARATOR MUX
LOOP FILTER 44 OUT_B

INPUT_B 5
ANALOG INPUT MUX
43 PVDD_B
VI_CM 6 42 PVDD_B
GND 7 GVDD_C
41 BST_B
AGND 8
40 BST_C
VREG 9 - 39 PVDD_C
INPUT_C 10 ANALOG +
LOOP FILTER 38 PVDD_C
PWM TIMING
CONTROL GATE-DRIVE 37 OUT_C
RECEIVER CONTROL
+ 36 OUT_C
INPUT_D 11 ANALOG
- 35 GND_C
LOOP FILTER
FREQ_ADJ 12 34 GND_C
GVDD_D
BST_D
OSC_IO+ 13
PVDD_D
OSC_IO- 14
PWM TIMING OUT_D
SD CONTROL GATE-DRIVE
/SD 15 RECEIVER CONTROL
GND_D
OTW1 33 GND_D
/OTW1 16
CLIP
READY
OTW2
M1
M2
M3
GVDD_C
GVDD_D
BST_D
OUT_D
OUT_D
PVDD_D
PVDD_D
GND_D
17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
/CLIP
READY
/OTW2
M1
M2
M3
GND
GND
GVDD_C
GVDD_D
BST_D
OUT_D
OUT_D
PVDD_D
PVDD_D
GND_D
59
HCD-GT3D
IC3004 BU9795AKS2 (LCD BOARD)
SEG31
SEG30
SEG29
SEG28
SEG27
SEG26
SEG25
SEG24
COM1
COM0
NC
NC
52 51 50 49 NC48 47 46 45 44 43 42 41 40
COM2 1 39 SEG23
COM3 2 38 SEG22
LCD voltage
generator Common Segment 37 NC
NC 3
driver driver
36 SEG21
VLCD 4
VDD 5 35 SEG20
LCD BIAS
SELECTOR Common Blink
timing DDRAM 34 SEG19
VSS 6 counter generator
OSCIO 7 33 SEG18
32 SEG17
CSB 8
Command Command
register Data Decoder 31 SEG16
SCL 9 OSCILLATOR Power On
Reset Serial inter face
30 SEG15
SDA 10
IF FILTER
29 NC
NC 11
28 SEG14
TEST 12
INHb 13 27 SEG13
14 15 16 17 18 19 20 21 22 23 24 25 26
SEG0
SEG1
SEG2
SEG3
SEG4
SEG5
SEG6
SEG7
SEG8
SEG9
SEG10
SEG11
SEG12
IC102 TC74VHC126FT (EK) (MOTHERBOARD BOARD (8/10))
1G 1 14 Vcc
1A 2 13 4G
1Y 3 12 4A
2G 4 11 4Y
2A 5 10 3G
2Y 6 9 3A
GND 7 8 3Y
IC103 BU4229F-TR (MOTHERBOARD BOARD (8/10))
Vout CT
4 3
–
+
Vref
1 2
GND VDD
IC106 MX25L3235EM2I-10G (MOTHERBOARD BOARD (9/10))

IC302 MX25L3235EM2I-10G (MOTHERBOARD BOARD (5/10))
CS 1
8 VCC
Address
X-Decoder
Generator
Memory Array
DO 2 Page Buffer
7 HOLD
Data
Register Y-Decoder
SRAM
Buffer
WP 3 Sense 6 CLK
Amplifier
Mode State HV
Logic Machine Generator
Clock Generator
GND 4 5 DI
Output
Buffer
60
HCD-GT3D
Ver. 1.2
IC305 BU33TD3WG-TR (MOTHERBOARD BOARD (5/10))
VDD 1
–
VREF
+
5 VOUT
GND 2 OCP
TSD
Discharge
STBY 4 NC
CE 3
IC306 EM638165TSD-6G (MOTHERBOARD BOARD (5/10))
VSS DQ8 VDDQ DQ9 DQ10 VSSQ DQ11 DQ12 VDDQ DQ13 DQ14 VSSQ DQ15 VSS
41 42 43 44 45 46 47 48 49 50 51 52 53 54
NC 40
1 VDD
UDQM 39
CLK 38 Clock
Bank D 2 DQ0
Generator
CKE 37 Bank C
Bank B 3 VDDQ
NC 36 Address Row
4 DQ1
Row Decoder
Address
A11 35 Buffer
Mode & Bank A 5 DQ2
Register Refresh
A9 34 Counter 6 VSSQ
A8 33 Sense Amplifier 7 DQ3
Command Decoder
Column
Column Decoder 8 DQ4
Control Logic
A7 32 Address
Buffer
Input & Output
& 9 VDDQ
Latch Circuit
A6 31 Refresh
Buffer
Counter Data Control Circuit 10 DQ5

A5 30
11 DQ6
A4 29
12 VSSQ
VSS 28
13 DQ7
27 26 25 24 23 22 21 20 19 18 17 16 15 14
VDD A3 A2 A1 A0 A10/AP BA1 BA0 CS RAS CAS WE LDQM VDD
IC401 AM5890S (MOTHERBOARD BOARD (6/10))

RESET
VOLD+
VOTK+
TRB_2
VOLD-
VOTK-
VINTK
VINLD
PGND
PGND
MUTE
VCCD
VCTL
BIAS
GND
Vcc2
30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15
Vcc2
Voltage
10K
Detection 15K
MUTE
+ 10K
-
+ - Spindle Actuator
Driver (6X)
-
Driver (4X)
+
25K
Thermal
Shut down
Vcc2
Vcc2
Vcc1
10K
+
25K -
+
-
+ Sled Actuator
25K
Driver (4X) Driver (6X)
-
Pre-DRV TRAY
10K DRIVER
1 2 3 4 5 6 7 8 9 10 11 12 13 14
VINFC
TRB_1
REGO2
VINSL+
REGO1
FWD
REV
Vcc1
VOTR-
VOTR+
VOSL+
VOSL-
VOFC-
VOFC+
IC452 NJM2903CV (TE1) (MOTHERBOARD BOARD (10/10))
A OUTPUT 1 8 V+
A- INPUT 2 A 7 B OUTPUT
- +
A+ INPUT 3 B 6 B- INPUT
+ -
V- 4 5 B+ INPUT
61
HCD-GT3D
IC453 TC7USB40FT (MOTHERBOARD BOARD (10/10))
NC 11
7 8 NC
GND 11
6 9 D+
D- 11
5
2D- 11
4
10 2D+
11 1D+
1D- 11
3
12 OE
S 11
2
13 VCC
NC 11
1
14 NC
IC502 TC62D723FNG (MOTHERBOARD BOARD (10/10))
GND 1
16 25 GND
SIN 2 Error detection result Output open/short detection circuit POR
data register 16 circuit 24 VDD
SCK 3
TRANS 4 Constant current output circuit Reference

voltage
/OUT0 5
Output delay circuit 23 REXT
/OUT1 6 16
8-bit
0-bit 15-bit
TSD DAC
Output ON/OFF setting data register circuit
8
Comparator
Comparator
Comparator
PWM
/OUT2 7 countor
/OUT3 8
/OUT4 9 16 16 16
/OUT5 10 PWM data registor
16-bit 16-bit Registor 3 16-bit
/OUT6 11 POD PWM Data PWM Data PWM Data
circuit for OUT0 for OUT1
(for output)
for OUT15
/OUT7 12 16 16 16 16-bit x 2
State setting
16-bit 16-bit Registor 2 16-bit register
/OUT8 13 16 PWM Data 16 PWM Data 16 PWM Data
for OUT0 for OUT1 (for synchronous) for OUT15
/OUT9 14 16 16 16
16-bit 16-bit 16-bit
/OUT10 15 Registor 1 PWM Data
PWM Data PWM Data
16 for OUT0 for OUT1 for OUT15
16
/OUT11 16
16 16 16
/OUT12 17 Command
control Data transfer control circuit
/OUT13 18 circuit
/OUT14 19 16 16
0-bit 15-bit
16-bit shift registor
SOUT
selection 22 SOUT
circuit
F/F
20 21
/OUT15
PWMCLK
IC602, IC605 SN74LV4052APWR (MOTHERBOARD BOARD (1/10))
2Y0 1 16 VCC
15 1Y2
2Y2 2
2-COM 3 14 1Y1
2Y3 4 13 1-COM
12 1Y0
2Y1 5
INH 6 11 1Y3
GND 7 10 A
GND 8 9 B
62
HCD-GT3D
IC604, IC615 PCM1754DBQR (MOTHERBOARD BOARD (3/10))
SYSTEM
SYSTEM
CLOCK 16 SCK
CLOCK
MANAGER
BCK 1 AUDIO SERIAL 15 FMT

DATA 2 SERIAL CONTROL 14 MUTE
LRCK 3 PORT PORT 13 DEMP
DGND 4
POWER
NC 5 4x/8x OVERSAMPLING DIGITAL
SUPPLY
VCC 6 FILTER & FUNCTION CONTROL
12 TEST
ENHANCED MULTILEVEL ZERO
11 ZEROA
DELTA-SIGMA MODULATOR DETECT
10 VCOM
9 AGND
D/A D/A
CONVERTER CONVERTER
OUTPUT AMP OUTPUT AMP

& LOW-PASS & LOW-PASS
FILTER FILTER
VLTUO 7
VRTUO 8
IC606 PCM1808PWR (MOTHERBOARD BOARD (4/10))

IC609 PCM1808PWR (MOTHERBOARD BOARD (3/10))
7 LRCK
BCK 8 Serial
DOUT 9 Interface
MD0 10 Mode/
Format
MD1 11
Control
FMT 12
Clock
and
6 SCKI
Timing
Control
x1/64
Decimation
Filter
with
High Pass Filter
5 DGND
Delta Sigma Delta Sigma
Modulator Modulator
4 VDD
Power
Supply
3 VCC
VINL 13 Antialias 2 AGND

LPF
Reference 1 VREF
VINR 14 Antialias
LPF
IC901 NJM41031F1 (TE2) (MOTHERBOARD BOARD (4/10))
VIN 4 6dB 75Ω DRIVER 3 VSAG

LPF
GND 5 2 VOUT
CLAMP
V+ 6 1 POWER SAVE
63
HCD-GT3D
Ver. 1.1
IC902 RN5B801-0002 (MOTHERBOARD BOARD (2/10))

VDDRF
GND
VDD
CP1
X2
X1
20 19 18 17 16 15
IISD 14 IISD
VDD VDD
Lch
Amplifier
CP2 13 FM Antenna Rch
Digital Signal Process
LOUT
Filter
Digital FM Stereo DAC
FRF1 24 AGC Mixer Demodulator Decoder
AMP
FM LNA ADC ROUT
AGC Digital AM RDS
AMP AGC Demodulator Decoder
LRCK
GNDRF 35 13 LRCK / LOUT
SW
Image Station IIS BCLK
Control Detector Generator LRCK
AMP ADC IISD
AM Antenna Digital Filters RSSI

ARF1 4 Calculation
AM LNA
12 BCLK / ROUT
SW
IIS Controller
ARF2 5
AM BCLK
TUNE
Clock Serial Interface / Registers

LOSC Generator XOSC 12C
HOST Controller
SPI
VDD
6 7 8 9 10 11
IIC / R
DSI
LA
CK
VDD
GND
DA
IC904 PCM9211PTR (MOTHERBOARD BOARD (2/10))

RXIN6/ALRCKIO
RXIN4/ASCKIO
RXIN5/ABCKIO
RXIN7/ADIN0
MS/ADR1
MC/SCL
VDDRX
MODE
RXIN1
RXIN2
RXIN3
RST
36 35 34 33 32 31 30 29 28 27 26 25
RXIN0 37 24 MD1/SDA
23 MD0/ADR0
RESET & SPI/I2C

RXIN10
RXIN11
DTOUT
RXIN0
RXIN1
RXIN2
RXIN3
RXIN4
RXIN5
RXIN6
RXIN7
RXIN8
RXIN9
MODE SETTING INTERFACE POWER

SUPPLY
22 DVDD
ALL
AUXIN0
21 DGND
REGISTER
POWER RECOUT1
SUPPLY RECOUT0
DIR
ADC CLOCK AUTO
GNDRX 38 ANALOG
(SCK/BCK/LRCK) DIR RXIN7
DIVIDER 20 SCKO
ADC DOUT MAIN 19 BCK
XMCKO AUXIN0 OUTPUT
SCKO/BCK/LRCK 18 LRCK
XTI 39 XMCKO (TO MPIO_A & MPO0/1) AUXIN1 PORT
OSC 17 DOUT
XTO 40 DIVIDER AUXIN2
RECOUT1
RECOUT0 MPO0/1 16 MPO1
DIR
CLOCK/DATA LOCK AUTO DITOUT SELECTOR 15 MPO0
PLL
RECOVERY DETECTION DIR
ADC
AUXIN0 DIT
AUXIN1
POWER SUPPLY
AUXIN2
AGND 41 DIR
VCC 42 ANALOG
AUTO
FILT 43 A/D DIR
CONVERTER ADC AUXOUT
14 MPIO_B3
ANALOG AUXIN0
MPIO_B 13 MPIO_B2
AUXIN1
SELECTOR
AUXIN2
VCOM 44 COM. SUPPLY ADC
AGNDAD 45
VCCAD 46
RXIN8
RXIN9
RXIN10
RXIN11
AUXIN1
VINL 47 A/D ADC

A/D CONVERTER
CONVERTER MODE ADC_STANDALONE
VINR 48 CONTROL
( TO MPIO_A)
SBCK/SLRCK
MPIO_C
MPIO_A
MPIO_B
MPO0
MPO1
SECONDARY BCK/LRCK EXTRA DIR MPIO_A MPIO_C

DIVIDER SELECTOR FUNCTIONS SELECTOR SELECTOR
1 2 3 4 5 6 7 8 9 10 11 12
ERROR/INT0
NPCM/INT1
MPIO_A0
MPIO_A1
MPIO_A2
MPIO_A3
MPIO_C0
MPIO_C1
MPIO_C2
MPIO_C3
MPIO_B0
MPIO_B1
64
HCD-GT3D
IC912 TC74VHC157FT (EK) (MOTHERBOARD BOARD (4/10))
SELECT 11
1 16 Vcc
S
1A 2 1A G 15 STROBE
INPUT
1B 3 1B 4A 14 4A
INPUT
OUTPUT 1Y 4 1Y 4B 13 4B
2A 5 2A 4Y 12 4Y OUTPUT
11
INPUT
2B 6 2B 3A 11 3A
INPUT
OUTPUT 2Y 7 2Y 3B 10 3B
3Y
GND 8 9 3Y OUTPUT
IC913 TC7WH157FK (MOTHERBOARD BOARD (4/10))
8 VCC
11
7 ST
11
6 SELECT
EN G
A 1 A Y 5 Y
B 2 B Y
Y 3
GND 4
IC914 PCM5101 (MOTHERBOARD BOARD (3/10))

'(03
AVDD
AGN
)/7
11 10 9 8
SCK 12
Current
Analog
0XWH
8x Interpolation Filter
7 2875
I/V
BCK 13 Segment
ELWǻȈ0RGXODWRU
Audio Interface
DAC
DIN 14
LRCK 15 Current
Analog
0XWH
Segment 6 287/
I/V
)07 16 DAC
Zero
Data $GYDQFHG0XWH&RQWURO
Detector
5 VNEG
Clock Halt
Detection 4 &$30
3 CPGND
2 CAPP
PLL Clock Power

UVP/Reset POR Ch. Pump Supply 1 CPVDD
17 18 19 20
;607
LDOO
DGND
DVD
65
HCD-GT3D
• IC Pin Function Descriptions

MOTHERBOARD BOARD (9/10) IC101 R7S7200032CFP-A (SYSTEM CONTROLLER)
Pin No. Pin Name I/O Description
1 SRC-RST0 - Not used
2 VIDEO-MUTE O Muting Control for Video
3 CDM-UNLOAD-SW I CDM UNLOAD SW
4 CDM-LOAD-SW I CDM LOAD SW
5 BT-RESET O Reset signal output to Bluetooth section
6 LCD_BCKLED O FL Backlight
7 Vcc - Power supply terminal (+3.3V)
8 BT-ON O Bluetooth on/off control signal output terminal for bluetooth section
9 Vss - Ground terminal
10 LCD-OSC O FL Frame Rate EXT CLOCK
11 PVcc - Power supply terminal (+3.3V)
12 NFC-INT I NFC Interrupt
13 MTK-POWER-CTRL O Power Control pin for MTK
14 AUDIO_CLK_OUT O Clock Signal from Aragon to MTK master clock
15 MTK-RESET O MTK Reset pin
16 MTK-BUSY O BUSY Signal communication between MTK
17 MTK-CLK I Clock Signal from MTK
19 MTK-XIFCS I MTK CHIP SELECT
20 MTK-SDI I Data In Signal from MTK
22 MTK-SDO O Data Out Signal to MTK
24 SSI3_BCK0 I Bit clock signal from MTK or DIR to Aragon
26 SSI3_LRCKO I LR clock signal from MTK or DIR to Aragon
27 C-CONT O Trigger port to start charging of SPM
28 SSI3_DI I Data signal from MTK or DIR to Aragon
29 SSI0_BCKO O Clock signal from Aragon to Wf DAC BCK
30 SSI0_LRCKO O Clock signal from Aragon to Wf DAC LRCK
32 SSI0_DO O Data Out from Aragon to Wf DAC
33 SSI2_DO O Data Out from Aragon to AUX OUT DAC
35 LCD-CLK O FL CIG serial data clock output
37 CKIO - Not used
38 LCD-CSB O FL CHIP SELECT
40 LCD-SDA O FL CIG serial data output
41 ANALOG-ASEL O Multiplexer selector A for Analog input
42 ANALOG-BSEL O Multiplexer selector B for Analog input
43 DEBUG-TxD O TxD (for Debug)
44 JOG+ O FILE SEARCH JOG POS
45 POWER-KEY I Power Key input terminal
47 USB-OC I USB Overcurrent Detection input port
48 RGB-SOUT O Serial data output to RGB driver
49 JOG- O FILE SEARCH JOG NEG
51 LINK-OUT-B O Selector B for Party Chain Signal
52 VBUS-OE O MTK Vbus Output enable control pin
53 NFC-RF-DET I NFC RF signal detection signal input from the NFC section
54 SSI1_DO O Data Out signal from Aragon to SWF DAC
66
HCD-GT3D

55 SSI1_DI I Data In Signal from ADC to Aragon
56 SD_FAST I SD FAST DETECT
PCONT-PSAVE-
57 O Main power on/off control signal output “H”:power on
PROTECT
59 LINK-DET I Party Chain input bias detection pin
60 USB_HOST_SEL O USB UPDATE SELECTOR
63 AC-CUT I AC off detection signal input from the reset signal IC “L”: AC Cut detected
64 DEBUG-RxD I RxD (for Debug)
65 BT-RxD I RX input signal from Bluetooth section
66 MD-CLKS O For ARAGON Internal SRC
67 RTC_X1 I RTC clock input terminal
68 RTC_X2 O RTC clock output terminal
69 PLLVcc - Power supply terminal (+3.3V)
70 EXTAL I System clock input terminal
71 XTAL O System clock output terminal
74 NMI - Non-maskable interrupt input terminal
76 RES I Reset signal
78 AMP PROTECT I Combination of TEMP, PS, SD & DC PROTECT
79 SPM-C-MON I Voice coil temperature monitor pin
SPM-AMBIENT-
80 I Ambient temperature monitor pin
TEMP
81 MODEL-DEST-IN I Model and Destination setting terminal (A/D input)
82 FAN-DET I Fan speed detect
83 MASTER-VOLUME I Jog dial pulse input from the MASTER VOLUME encoder (A/D input)
84 AD-KEY0 I Key input terminal (A/D input)
85 AD-KEY1 I Key input terminal (A/D input)
86 AVcc - Power supply terminal (+3.3V)
87 AVss - Ground terminal
88 AVref - A/D Converter reference voltage input terminal (+3.3V)
89 BSCANP - Boundary scan setting pin
91 AUDIO_X1 I Audio clock input terminal
92 AUDIO_X2 O Audio clock output terminal
94 /LINE-MUTE O Muting Control Switch for Party Chain. “L”: mute On
96 PCONT-BTSTBY O BT Standby Power Control Pin. “H”: ON
97 TRST I Debugging interface: Initialization-signal input pin
98 TDO O Debugging interface: Serial output pin for instructions and data
99 TDI I Debugging interface: Serial input pin for instructions and data
100 TMS I Debugging interface: Test-mode select signal input pin
101 TCK I Debugging interface: Test-clock input pin
TEST-MON103/
103 O Test port for software checking
SD_D2_0
TEST-MON104/
SD_D3_0
TEST-MON106/
SD_CMD_0
67
HCD-GT3D

TEST-MON108/
SD_CLK
TEST-MON110/
SD_D0_0
ANALOG-DSEL/
111 O ANALOG INPUT SELECTOR D
SD_D1_0
RGB-TRANS-LED-
112 O Transfer signal to RGB driver (driver for Speaker LED)
SPK/SD_WP_0
RGB-TRANS-LED/
113 O Transfer signal to RGB driver
SD_CD_0
114 ST-RDS I Input for RDS Text Detect Signal (L: RDS Detect)
115 ST-CE O Tuner IC: Tuner enable input pin
117 PCONT-DAMP O Digital Amp Module Power Control Pin. “H”: ON
118 RGB-PWM-CLK O PWM clock signal to RGB driver
120 /AMP-RESET O Digital Amp Reset Pin
122 CD-MOTOR+ O CDM turning motor control signal output
124 CD-MOTOR- O CDM turning motor control signal output
125 DIR_CP-CLK O DIR & CP share clock
126 DIR_CP-DATA I/O DIR & CP share data
127 ST-CLK O Tuner IC: Clock signal for IIC communication
128 ST-DATA I/O Tuner IC: Data signal for IIC communication
129 RELAY CONTROL O Relay control
130 DIR INT0 I DIR INTERRUPT 0
131 NFC_CLK O NFC CLOCK
132 NFC_DATA I/O Two-way data bus with the NFC
133 BT-TxD O TX signal output terminal for Bluetooth section
134 LCD_INHB O FL inhibit pin
135 SIRCS I Remote control signal input
136 DIR INT1 I DIR INTERRUPT 1
137 RGB-SCLK O Serial clock output to RGB driver
139 USB_X1 I USB clock input terminal
140 USB_X2 O USB clock output terminal
141 USBDPVcc - Power supply terminal (+3.3V)
142 USBDPVss - Ground terminal
143 DM1 - Not used
144 DP1 - Not used
145 VBUSIN1 - Not used
146 USBDVcc - Power supply terminal (+3.3V)
147 USBDVss - Ground terminal
148 USBDPVcc - Power supply terminal (+3.3V)
149 USBDPVss - Ground terminal
150 USB_DM0 I/O D- PIN FOR USB 2.0
151 USB_DP0 I/O D+ PIN FOR USB 2.0
152 VBUSIN0 O VBUS +5.0V supply monitoring pin
153 USBDVcc - Power supply terminal (+3.3V)
154 USBDVss - Ground terminal
155 REFRIN I Reference input
156 USBAPVss - Ground terminal
157 USBAPVcc - Power supply terminal (+3.3V)
158 USBAVcc - Power supply terminal (+3.3V)
68
HCD-GT3D

159 USBAVss - Ground terminal
160 USBUVcc - Power supply terminal (+3.3V)
161 USBUVss - Ground terminal
164 ANALOG-CSEL O ANALOG INPUT SELECTOR C
165 DIR-RESET O DIR RESET
166 Q-FLASH-SIO2 I/O QSPI: Data I/O pins for channel 0
168 Q-FLASH-CLK O Clock signal to QSPI
169 Q-FLASH-CS O Slave select pin to QSPI
173 MIC-DETECT I Mic Input Detection pin. “H”: Mic detected
175 LINK-SET O Party Chain output bias pin
176 LINK-OUT-A O Selector A for Party Chain Signal
69
HCD-GT3D
MOTHERBOARD BOARD (5/10) IC301 CXD9990R (CD RF AMP FOCUS/TRACKING ERROR AMP, CD SYSTEM
PROCESSOR, DIGITAL SERVO PROCESSOR)

1 RF_C I RF main beam C input from the optical pick-up block
2 RF_D I RF main beam D input from the optical pick-up block
3 RF_E I RF sub beam E input from the optical pick-up block
4 RF_F I RF sub beam F input from the optical pick-up block
5 AVDD12_2 - Power supply terminal (+1.2V) (for analog system)
7 XTALI I System clock input terminal (27 MHz)
8 XTALO O System clock output terminal (27 MHz)
9 AGND33 - Ground terminal (for analog system)
10 V20 O Reference voltage (+2V) output to the optical pick-up block
11 V14/VREF0 O Reference voltage (+1.4V) output to the coil / motor driver
12 REXT I Current reference input terminal
13 MDI1 I Laser power monitor input from the optical pick-up block
14 LDO1 O Laser diode drive signal output to the optical pick-up block (for CD)
15 LDO2 O Laser diode drive signal output to the optical pick-up block (for DVD)
17 DMO O Spindle motor control signal output to the motor driver
18 FMO O Sled motor control signal output to the motor driver
19 CD_VR O Variable resistor control signal output to the optical pick-up block (for CD)
20 DVD_VR O Variable resistor control signal output to the optical pick-up block (for DVD)
21 TRO O Tracking coil control signal output to the coil / motor driver
22 FOO O Focus coil control signal output to the coil / motor driver
23 MSW O CD/DVD selection signal output terminal “L”: DVD, “H”: CD
24 USB_DM I/O Two-way USB data (-) bus terminal
25 USB_DP I/O Two-way USB data (+) bus terminal
26 VDD33_USB - Power supply terminal (+3.3V) (for USB)
27 VSS33_USB - Ground terminal (for USB)
28 PAD_VRT I/O USB generating reference current terminal
29 VDD12_USB - Power supply terminal (+1.2V) (for USB)
30 SF_CS# O Chip select signal output to the serial flash
31 SF_DO O Serial data output to the serial flash
32 SF_DI I Serial data input from the serial flash
33 SF_CK O Serial clock signal output to the serial flash
34 IFSCK O Serial data transfer clock signal output to the system controller
35 IFSDO O Serial data output to the system controller
36 RX I Serial data input terminal for flash writing
37 TX O Serial data output terminal for flash writing
38 PRST# I Reset signal input from the system controller “L”: reset
39 NC - Not used
40 IFSDI I Serial data input from the system controller
41 IFBSY I Communication initialization request signal input from the system controller
42 IFCS# O Communication initialization request acknowledge signal output to the system controller
43 MFISW - Not used
44 LIMITSW - Not used
45 MUTE O Muting signal output to the coil/motor driver (for focus/tracking coil and sled motor)
46 EEWP O Write protect signal output with the EEPROM
47 SDA I/O Two-way I2C data signal with EEPROM
48 SCL I/O Two-way I2C clock signal with EEPROM
49 NC - Not used
50 DVSS33 - Ground terminal (for digital system)
51 DVDD33 - Power supply terminal (+3.3V) (for digital system)
52 to 55 RD0 to RD3 I/O Two-way data bus with the SD-RAM
70
HCD-GT3D

61 DQM0 O Data mask signal output to the SD-RAM
70 DQM1 O Data mask signal output to the SD-RAM
72 RCLK O Clock signal output to the SD-RAM
73 to 79 RA11, RA9 to RA4 O Address signal output to the SD-RAM
80 RWE# O Write enable signal output to the SD-RAM
81 DVSS12 - Ground terminal (for digital system)
82 CAS# O Column address strobe signal output to the SD-RAM
83 RAS# O Row address strobe signal output to the SD-RAM
85 BA0 O Bank address signal output to the SD-RAM
86 BA1 O Bank address signal output to the SD-RAM
88 to 92 RA10, RA0 to RA3 O Address signal output to the SD-RAM
93 SPDIF - Not used
94 XMAMUTE - Not used
95 NC - Not used
96 DACVDDC - Power supply terminal (+3.3V) (for D/A converter)
97 VREF I Band gap reference voltage terminal
98 FS I Full scale adjustment terminal
99 DACVSSC - Ground terminal (for D/A converter)
100 CVBS O Composite video signal output terminal
101 DACVDDB - Power supply terminal (+3.3V) (for D/A converter)
102 SY/Y/G - Not used
103 SC/CB/B - Not used
104 CR/R - Not used
105 AADVSS - Ground terminal (for D/A converter)
106 ADIN I Audio data input from the A/D converter
107 NC - Not used
108 NC - Not used
109 AADVDD - Power supply terminal (+3.3V) (for D/A converter)
110 ADACVSS2 - Ground terminal (for D/A converter)
111 ADACVSS1 - Ground terminal (for D/A converter)
112 ACLK O Master clock signal output
113 ABCK O Bit clock signal output
114 NC - Not used
115 AVCM I Audio D/A converter reference voltage terminal
116 NC - Not used
117 ALRCK O L/R sampling clock signal output
118 ASDATA0 O Audio data output
119 ADACVDD1 - Power supply terminal (+3.3V) (for D/A converter)
120 ADACVDD2 - Power supply terminal (+3.3V) (for D/A converter)
122 AGND12 - Ground terminal (for analog system)
123 RFIP I AC coupled RF signal input from the optical pick-up block
124 OPDIST I Optical pick-up block type selection
125 IOPMON/OPO I Power monitor terminal
126 SPFG/OP I Spindle motor hall sensor input from the motor driver
127 RF_A I RF main beam A input from the optical pick-up block
128 RF_B I RF main beam B input from the optical pick-up block
71
HCD-GT3D
Ver. 1.2 SECTION 7
EXPLODED VIEWS
Note:
• The mechanical parts with no reference • Abbreviation
number in the exploded views are not sup- The components identified by mark 0
AR : Argentina model
plied. or dotted line with mark 0 are critical for
• Items marked “*” are not stocked since safety.
E4 : African model
they are seldom required for routine Replace only with part number specified.
EA : Saudi Arabia model
service. LA9 : Latin-American model The components identified by mark 9 con-
Some delay should be anticipated MY : Malaysia model tain confidential information.
when ordering these items. RU : Russian model Strictly follow the instructions whenever the
• -XX and -X mean standardized parts, so TH : Thai model components are repaired and/or replaced.
they may have some difference from the
original one.
7-1. SIDE PANEL SECTION
#2 #1
D A
#1
top panel section
F
C
B G
E
#1
1
#1
A
D
F
#1
C B
2
G
E
loading panel section #1
#2
#1
1 (Type A) 1 (Type B)
Note 1: The screw type which screw between “PANEL, SIDE and PANEL, TOP” and “PANEL, SIDE and CHASSIS” for
this unit have been changed in the midway of production. About the screw type discrimination, refer to “SCREW
TYPE DISCRIMINATION BEFORE DISASSEMBLE THE PANEL, SIDE” on servicing notes (page 6).
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
1 4-546-397-01 SCREW, TAPPING (HEX) (Type A) #1 7-685-646-71 SCREW +BVTP 3X8 TYPE2 IT-3
1 4-162-271-01 SCREW, TAPPING (Type B)
2 X-2590-652-2 PANEL, SIDE (L) ASSY #2 7-685-646-79 SCREW +BVTP 3X8 TYPE2 IT-3
3 X-2590-653-2 PANEL, SIDE (R) ASSY
72
HCD-GT3D
Ver. 1.2

• Bottom view
54
55
not supplied
56 (BUTTON board)
56 54
56
56
56
not supplied
(MIC board)
57
51
54
52
not supplied
not supplied 53
Note 1: When the VOLUME knob assy or MIC knob is replaced, Note 2: If wire (flat type) is replaced, install it after bending it
refer to “NOTE OF REPLACING THE VOLUME KNOB in the same form as that before replacement.
ASSY OR MIC KNOB” on servicing notes (page 7).
51 4-549-432-01 KNOB, MIC 55 1-849-009-11 WIRE (FLAT TYPE) (11 CORE)
52 4-549-431-01 KNOB, FUNCTION
53 X-2590-651-1 KNOB, VOLUME ASSY 56 4-543-517-02 HEMILON, 5X5X0.4
54 3-087-053-01 +BVTP2.6 (3CR) 57 X-2590-580-5 PANEL, TOP ASSY
73
HCD-GT3D
Ver. 1.2
7-3. LOADING PANEL SECTION
#1
not supplied
(OPTICAL board)
A
B
#1
CDM section
#1 #1
#1 #1
not supplied
B #1
#1
not supplied
101
not supplied
MOTHERBOARD board section

102
not supplied
Ref. No. Part No. Description Remark

101 X-2590-650-4 PANEL, LOADING ASSY
102 4-295-431-01 SPRING, LOADING
#1 7-685-646-71 SCREW +BVTP 3X8 TYPE2 IT-3
74
HCD-GT3D
Ver. 1.2
7-4. MOTHERBOARD BOARD SECTION

• Rear view
151
#1 not supplied
153
not supplied
B
not supplied
(SPLITTER board)
#1
A
not supplied not supplied
#1
154
152
#1
chassis section
Note 1: When the complete DAMP board is replaced, refer to Note 2: If wire (flat type) is replaced, install it after bending it
“NOTE OF REPLACING THE IC1001 ON THE DAMP in the same form as that before replacement.
BOARD AND THE COMPLETE DAMP BOARD” on
151 1-849-011-11 WIRE (FLAT TYPE) (19 CORE) 154 A-2071-986-A MOTHERBOARD BOARD, COMPLETE
152 A-2061-348-A DAMP BOARD, COMPLETE (for SERVICE) (AUS)
153 1-849-010-11 WIRE (FLAT TYPE) (25 CORE) 154 A-2071-987-A MOTHERBOARD BOARD, COMPLETE
154 A-2071-965-A MOTHERBOARD BOARD, COMPLETE (for SERVICE) (MY, TH)
(for SERVICE) (AR, LA9) 154 A-2071-988-A MOTHERBOARD BOARD, COMPLETE
154 A-2071-984-A MOTHERBOARD BOARD, COMPLETE (for SERVICE) (RU)
(for SERVICE) (EA, E4) #1 7-685-646-71 SCREW +BVTP 3X8 TYPE2 IT-3
75
HCD-GT3D
Ver. 1.2
7-5. CHASSIS SECTION
213 201 204

not supplied
(RU, EA, MY, AUS, E4) not supplied 205
not supplied
not supplied
206
B
not supplied
201 not supplied
not supplied
not supplied
208
202
207 not supplied
#1 B
C
A 208
#1
A
not supplied
not supplied D
not supplied
not supplied #1
not supplied
203 not supplied
not supplied
C 209
#1
211
210
D
front panel section

#1
212
201 3-077-331-21 +BV3 (3-CR) 208 3-559-407-21 CUSHION, STOPPER
* 202 3-703-150-11 CLAMP 209 4-532-593-01 SCREW (4X13) (TR-184A)
0 203 1-855-006-41 FAN, DC 210 4-238-407-12 SCREW (1) (4X20), +BV TAPPING
204 2-677-839-01 +PWH 3X8 (SUMITITE)
0 205 1-844-234-21 AC INLET 211 1-859-087-11 LOUDSPEAKER (20CM)-087-11
212 4-546-027-01 FOOT, RUBBER
0 206 A-2061-350-A SMPS BOARD, COMPLETE * 213 1-500-082-11 CLAMP, SLEEVE FERRITE (RU, EA, MY, AUS, E4)
207 4-558-595-01 STEP SCREW M4 #1 7-685-646-71 SCREW +BVTP 3X8 TYPE2 IT-3
76
HCD-GT3D
Ver. 1.2

• Rear view
not supplied
257
254
255
256 not supplied not supplied
not supplied
not supplied
253
ND3000
not supplied
252 not supplied
not supplied
not supplied
(LCD board)
254
not supplied
not supplied
251
not supplied 258

not supplied
254 (SPK_HLED board)
not supplied
Note: If wire (flat type) is replaced, install it after bending

it in the same form as that before replacement.
251 1-849-013-11 WIRE (FLAT TYPE) (13 CORE) 256 1-849-015-11 WIRE (FLAT TYPE) (6 CORE)
252 1-849-014-11 WIRE (FLAT TYPE) (10 CORE) 257 8-989-602-00 RC-S730 (WW)
253 1-492-699-11 BLUETOOTH MODULE 258 X-2590-649-3 PANEL, FRONT (SW) ASSY
254 3-087-053-01 +BVTP2.6 (3CR) ND3000 1-812-078-11 LIQUID CRYSTAL DISPLAY
255 4-449-063-01 CUSHION (NFC)
77
HCD-GT3D
Ver. 1.2
7-7. CDM SECTION
#1
CD mechanism section
(CDM90-DVBU204//M)
302
302 303
301 not supplied
not supplied
303
302
301
303
302
303
305
305
304 304
not supplied
Ref. No. Part No. Description Remark

301 2-345-115-01 SCREW (S), FLOAT
302 4-535-577-01 STEP SCREW M2.6
303 4-533-382-01 INSULATOR
304 4-533-939-01 SPRING, INSULATOR (F)
305 4-533-940-01 SPRING, INSULATOR (R)
#1 7-685-646-71 SCREW +BVTP 3X8 TYPE2 IT-3
78
HCD-GT3D
Ver. 1.2
7-8. CD MECHANISM SECTION

(CDM90-DVBU204//M)
not
supplied
351 (including MS-476 board)
not supplied
352
353
353
353
354
353
not supplied
not supplied
not supplied
not supplied
(MS-476 board)
356
not supplied
357
355
not supplied
not supplied
Note : If cable, flexible flat and wire (flat type) is

replaced, install it after bending it in the
same form as that before replacement.
351 A-1896-391-B LOADING COMPLETE ASSY (T) 355 1-469-829-11 CORE, FERRITE
(including MS-476 board)
352 3-087-599-01 INSULATOR SCREW 356 1-849-012-11 WIRE (FLAT TYPE) (24 CORE)
353 2-634-618-21 INSULATOR 357 1-849-016-11 WIRE (FLAT TYPE) (5 CORE)
0 354 A-2046-956-A SERVICE, OPTICAL DEVICE(7G)
79
HCD-GT3D
Ver. 1.2 SECTION 8
BUTTON
ELECTRICAL PARTS LIST
Note:
• Due to standardization, replacements in • SEMICONDUCTORS
The components identified by mark 0
the parts list may be different from the In each case, u: μ, for example:
or dotted line with mark 0 are critical for
parts specified in the diagrams or the com- uA. . : μA. . , uPA. . , μPA. . ,
safety.
ponents used on the set. uPB. . : μPB. . , uPC. . , μPC. . ,
Replace only with part number specified.
• -XX and -X mean standardized parts, so uPD. . : μPD. .
they may have some difference from the • CAPACITORS
When indicating parts by reference num-
original one. uF: μF
ber, please include the board name.
• RESISTORS • COILS
All resistors are in ohms. uH: μH
METAL: Metal-film resistor. • Abbreviation The components identified by mark 9
METAL OXIDE: Metal oxide-film resistor. AR : Argentina model contain confidential information.
F: nonflammable. AUS : Australian model Strictly follow the instructions whenever the
• Items marked “*” are not stocked since E4 : African model components are repaired and/or replaced.
they are seldom required for routine ser- EA : Saudi Arabia model
vice. LA9 : Latin-American model
Some delay should be anticipated when MY : Malaysia model
ordering these items. RU : Russian model
TH : Thai model
BUTTON BOARD R3141 1-216-835-11 METAL CHIP 15K 5% 1/10W
************* R3142 1-216-819-11 METAL CHIP 680 5% 1/10W
R3143 1-216-821-11 METAL CHIP 1K 5% 1/10W
< CAPACITOR > R3144 1-216-823-11 METAL CHIP 1.5K 5% 1/10W
R3145 1-216-823-11 METAL CHIP 1.5K 5% 1/10W
C3107 1-118-695-91 CERAMIC CHIP 0.01uF 5% 50V
C3111 1-118-695-91 CERAMIC CHIP 0.01uF 5% 50V R3146 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
C3113 1-115-872-11 ELECT 2.2uF 20% 50V R3147 1-216-827-11 METAL CHIP 3.3K 5% 1/10W
C3117 1-115-416-11 CERAMIC CHIP 0.001uF 5% 25V R3148 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R3149 1-218-867-11 METAL CHIP 6.8K 0.5% 1/10W
< CONNECTOR > R3150 1-216-833-11 METAL CHIP 10K 5% 1/10W
CN3100 1-779-279-11 CONNECTOR, FFC (LIF (NON-ZIF)) 11P < VARISTOR >
< DIODE > RV3100 1-227-918-11 RES, VAR, CARBON 50K (MIC LEVEL)
D3100 6-504-215-01 DI HL-364V620MZ-T < SWITCH >

D3105 6-504-213-01 DI HL-364B460MZ-T
S3100 1-762-875-21 SWITCH, TACTILE (:/1)
< ROTARY ENCODER > S3101 1-762-875-21 SWITCH, TACTILE (x)
S3102 1-762-875-21 SWITCH, TACTILE (N)
EN3100 1-493-009-11 ENCODER, ROTARY (MULTI CONTROL) S3103 1-762-875-21 SWITCH, TACTILE (-PAIRING BLUETOOTH)
EN3101 1-493-007-11 ENCODER, ROTARY (VOLUME/DJ CONTROL) S3104 1-762-875-21 SWITCH, TACTILE (MEGA BASS)
< JUMPER RESISTOR > S3105 1-762-875-21 SWITCH, TACTILE (LIGHT MODE)
S3106 1-762-875-21 SWITCH, TACTILE (ENTER)
JR3100 1-216-296-11 SHORT CHIP 0 S3107 1-762-875-21 SWITCH, TACTILE (FUNCTION)
JR3101 1-216-296-11 SHORT CHIP 0 S3108 1-762-875-21 SWITCH, TACTILE (SOUND FIELD)
JR3102 1-216-296-11 SHORT CHIP 0 S3109 1-762-875-21 SWITCH, TACTILE (DJ EFFECT FLANGER)
JR3103 1-216-296-11 SHORT CHIP 0
JR3104 1-216-296-11 SHORT CHIP 0 S3110 1-762-875-21 SWITCH, TACTILE (DJ EFFECT ISOLATOR)
S3111 1-762-875-21 SWITCH, TACTILE (DJ EFFECT DJ OFF)
< RESISTOR > S3112 1-762-875-21 SWITCH, TACTILE (DJ EFFECT SAMPLER)
S3113 1-762-875-21 SWITCH, TACTILE (PARTY CHAIN)
R3123 1-216-864-11 SHORT CHIP 0 S3114 1-762-875-21 SWITCH, TACTILE (Z)
R3124 1-216-864-11 SHORT CHIP 0
R3125 1-216-833-11 METAL CHIP 10K 5% 1/10W S3115 1-762-875-21 SWITCH, TACTILE (PARTY LIGHT)
R3129 1-216-833-11 METAL CHIP 10K 5% 1/10W S3116 1-762-875-21 SWITCH, TACTILE (FOOTBALL)
R3130 1-216-819-11 METAL CHIP 680 5% 1/10W S3117 1-762-875-21 SWITCH, TACTILE (S3 TUNING - .)
S3118 1-762-875-21 SWITCH, TACTILE (S4 TUNING + >)
R3131 1-216-821-11 METAL CHIP 1K 5% 1/10W S3119 1-762-875-21 SWITCH, TACTILE (S1 -)
R3132 1-216-823-11 METAL CHIP 1.5K 5% 1/10W
R3133 1-216-823-11 METAL CHIP 1.5K 5% 1/10W S3120 1-762-875-21 SWITCH, TACTILE (S2 +)
R3134 1-216-825-11 METAL CHIP 2.2K 5% 1/10W S3121 1-762-875-21 SWITCH, TACTILE (VOCAL FADER)
R3135 1-216-827-11 METAL CHIP 3.3K 5% 1/10W S3122 1-762-875-21 SWITCH, TACTILE (MIC ECHO)
S3123 1-762-875-21 SWITCH, TACTILE (REC TO USB)
R3136 1-216-829-11 METAL CHIP 4.7K 5% 1/10W *************************************************************
R3137 1-218-867-11 METAL CHIP 6.8K 0.5% 1/10W
R3138 1-216-833-11 METAL CHIP 10K 5% 1/10W
R3139 1-216-837-11 METAL CHIP 22K 5% 1/10W
R3140 1-216-835-11 METAL CHIP 15K 5% 1/10W
80
HCD-GT3D
Ver. 1.1
DAMP
A-2061-348-A DAMP BOARD, COMPLETE C1092 1-112-692-11 CERAMIC CHIP 1000PF 5% 50V
********************* * C1095 1-118-360-11 CERAMIC CHIP 0.1uF 10% 25V
< CAPACITOR > C1105 1-162-966-91 CERAMIC CHIP 0.0022uF 10% 50V
C1001 1-118-347-11 CERAMIC CHIP 0.1uF 10% 25V C1106 1-162-966-91 CERAMIC CHIP 0.0022uF 10% 50V
C1003 1-116-716-11 CERAMIC CHIP 10uF 10% 16V C1108 1-126-193-11 ELECT CHIP 1uF 20% 50V
C1004 1-128-991-21 ELECT CHIP 10uF 20% 50V C1117 1-165-908-11 CERAMIC CHIP 1uF 10% 10V
* C1005 1-116-714-11 CERAMIC CHIP 22uF 20% 6.3V C1118 1-165-908-11 CERAMIC CHIP 1uF 10% 10V
C1007 1-162-960-11 CERAMIC CHIP 220PF 10% 50V C1119 1-165-908-11 CERAMIC CHIP 1uF 10% 10V
C1011 1-112-692-11 CERAMIC CHIP 1000PF 5% 50V C1121 1-118-066-11 CERAMIC CHIP 0.1uF 10% 100V
* C1021 1-118-360-11 CERAMIC CHIP 0.1uF 10% 25V C1125 1-116-708-11 CERAMIC CHIP 47uF 20% 6.3V
C1022 1-116-782-91 CERAMIC CHIP 2.2uF 10% 100V C1126 1-112-247-31 ELECT 220uF 20% 35V
C1037 1-118-386-11 CERAMIC CHIP 0.1uF 10% 16V * C1131 1-118-360-11 CERAMIC CHIP 0.1uF 10% 25V
C1039 1-164-934-11 CERAMIC CHIP 330PF 10% 50V * C1133 1-118-360-11 CERAMIC CHIP 0.1uF 10% 25V
C1043 1-162-966-91 CERAMIC CHIP 0.0022uF 10% 50V C1136 1-137-765-21 ELECT CHIP 47uF 20% 16V
C1049 1-118-369-11 CERAMIC CHIP 0.022uF 10% 50V C1142 1-118-933-11 ELECT (BLOCK) 3300uF 20% 71V
C1052 1-162-966-91 CERAMIC CHIP 0.0022uF 10% 50V C1147 1-112-514-91 CERAMIC CHIP 1500PF 5% 50V
* C1060 1-118-360-11 CERAMIC CHIP 0.1uF 10% 25V C1168 1-118-066-11 CERAMIC CHIP 0.1uF 10% 100V
C1062 1-116-708-11 CERAMIC CHIP 47uF 20% 6.3V
< CONNECTOR >
C1063 1-116-708-11 CERAMIC CHIP 47uF 20% 6.3V
C1067 1-114-831-91 CERAMIC CHIP 1uF 10% 100V CN1001 1-820-117-51 CONNECTOR, FFC/FPC 19P
C1068 1-114-831-91 CERAMIC CHIP 1uF 10% 100V CN1004 1-770-469-21 PIN, CONNECTOR (PC BOARD) 2P
C1074 1-116-911-21 CERAMIC CHIP 1uF 10% 250V CN1005 1-691-770-11 PLUG (MICRO CONNECTOR) 8P
C1075 1-116-911-21 CERAMIC CHIP 1uF 10% 250V CN1007 1-564-320-00 PIN, CONNECTOR (3.96mm PITCH) 2P
C1076 1-118-066-11 CERAMIC CHIP 0.1uF 10% 100V < DIODE >
C1078 1-116-405-11 CERAMIC CHIP 0.01uF 10% 100V D1001 6-500-400-01 DIODE BAV99-215
D1006 6-500-400-01 DIODE BAV99-215
C1081 1-116-405-11 CERAMIC CHIP 0.01uF 10% 100V D1007 8-719-073-35 DIODE RB551V-30TE-17
C1083 1-128-403-11 ELECT CHIP 47uF 20% 35V D1008 6-500-400-01 DIODE BAV99-215
C1089 1-128-991-21 ELECT CHIP 10uF 20% 50V D1013 6-502-961-01 DI DA2J10100L
* C1090 1-118-360-11 CERAMIC CHIP 0.1uF 10% 25V D1014 6-502-970-01 DI DZ2J068M0L
D1016 6-503-987-01 DI RF05VAM2STR
C1091 1-128-991-21 ELECT CHIP 10uF 20% 50V D1017 8-719-073-35 DIODE RB551V-30TE-17
Note 1: When the complete DAMP board is replaced, re- Note 2: When the C1126, C1127, C1128, C1129 and C1142 on the
fer to “NOTE OF REPLACING THE IC1001 ON DAMP board are replaced, spread the bond referring to “BOND
THE DAMP BOARD AND THE COMPLETE DAMP FIXATION OF ELECTRIC PARTS” on servicing notes (page 6).
BOARD” on servicing notes (page 5).
81
HCD-GT3D
Ver. 1.1
DAMP
< IC > R1037 1-216-819-11 METAL CHIP 680 5% 1/10W
R1052 1-250-535-11 METAL CHIP 47K 1% 1/16W
IC1001 6-716-817-01 IC TAS5630BPHDR * R1053 1-250-507-11 METAL CHIP 3.3K 1% 1/16W
IC1003 6-716-462-01 IC BD00GA3WEFJ-E2
IC1004 8-759-274-71 IC NJM4565M (TE2) R1062 1-216-833-11 METAL CHIP 10K 5% 1/10W
IC1005 8-759-274-71 IC NJM4565M (TE2) R1063 1-216-827-11 METAL CHIP 3.3K 5% 1/10W
R1064 1-216-837-11 METAL CHIP 22K 5% 1/10W
< JUMPER > R1065 1-216-789-11 METAL CHIP 2.2 5% 1/10W
R1066 1-216-791-11 METAL CHIP 3.3 5% 1/10W
JC1019 1-216-295-91 SHORT CHIP 0
JC1020 1-216-295-91 SHORT CHIP 0 R1067 1-216-789-11 METAL CHIP 2.2 5% 1/10W
R1068 1-216-789-11 METAL CHIP 2.2 5% 1/10W
< COIL > R1069 1-216-837-11 METAL CHIP 22K 5% 1/10W
R1070 1-216-838-11 METAL CHIP 27K 5% 1/10W
L1006 1-482-158-11 INDUCTOR 10uH R1072 1-216-821-11 METAL CHIP 1K 5% 1/10W
L1007 1-482-158-11 INDUCTOR 10uH
R1078 1-216-833-11 METAL CHIP 10K 5% 1/10W
< TRANSISTOR > R1079 1-216-833-11 METAL CHIP 10K 5% 1/10W
R1080 1-216-833-11 METAL CHIP 10K 5% 1/10W
Q1003 8-729-216-22 TRANSISTOR 2SA1162-G
Q1004 8-729-216-22 TRANSISTOR 2SA1162-G R1081 1-216-833-11 METAL CHIP 10K 5% 1/10W
Q1006 6-552-892-01 TR LSCR523UBFS8TL R1082 1-216-845-11 METAL CHIP 100K 5% 1/10W
Q1010 6-552-746-01 TR DSA700300L R1083 1-216-845-11 METAL CHIP 100K 5% 1/10W
R1085 1-216-841-11 METAL CHIP 47K 5% 1/10W
Q1014 8-729-216-22 TRANSISTOR 2SA1162-G
Q1015 8-729-216-22 TRANSISTOR 2SA1162-G R1087 1-216-791-11 METAL CHIP 3.3 5% 1/10W
Q1016 8-729-216-22 TRANSISTOR 2SA1162-G R1088 1-216-791-11 METAL CHIP 3.3 5% 1/10W
Q1017 8-729-216-22 TRANSISTOR 2SA1162-G R1091 1-216-827-11 METAL CHIP 3.3K 5% 1/10W
Q1018 6-553-509-01 TR KTA1542T-RTK/P R1092 1-216-827-11 METAL CHIP 3.3K 5% 1/10W
R1106 1-216-842-11 METAL CHIP 56K 5% 1/10W
Q1019 6-553-083-01 TR PBSS4160T
R1127 1-216-834-11 METAL CHIP 12K 5% 1/10W
< RESISTOR > R1128 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R1001 1-208-715-11 METAL CHIP 22K 0.50% 1/16W R1129 1-216-839-11 METAL CHIP 33K 5% 1/10W
R1002 1-218-941-81 METAL CHIP 100 5% 1/16W R1130 1-216-805-11 METAL CHIP 47 5% 1/10W
R1004 1-218-941-81 METAL CHIP 100 5% 1/16W R1132 1-216-821-11 METAL CHIP 1K 5% 1/10W
R1008 1-218-941-81 METAL CHIP 100 5% 1/16W R1134 1-216-295-91 SHORT CHIP 0
R1009 1-208-911-11 METAL CHIP 10K 0.50% 1/16W R1135 1-216-295-91 SHORT CHIP 0
R1011 1-216-791-11 METAL CHIP 3.3 5% 1/10W R1136 1-216-295-91 SHORT CHIP 0
R1017 1-216-791-11 METAL CHIP 3.3 5% 1/10W R1138 1-216-836-11 METAL CHIP 18K 5% 1/10W
R1020 1-216-791-11 METAL CHIP 3.3 5% 1/10W R1141 1-208-911-11 METAL CHIP 10K 0.50% 1/16W
R1021 1-216-791-11 METAL CHIP 3.3 5% 1/10W R1145 1-218-855-11 METAL CHIP 2.2K 0.50% 1/10W
R1022 1-216-791-11 METAL CHIP 3.3 5% 1/10W R1147 1-216-845-11 METAL CHIP 100K 5% 1/10W
R1023 1-216-791-11 METAL CHIP 3.3 5% 1/10W R1148 1-216-824-11 METAL CHIP 1.8K 5% 1/10W
* R1028 1-250-684-11 METAL CHIP 680K 1% 1/10W R1153 1-216-824-11 METAL CHIP 1.8K 5% 1/10W
R1031 1-216-849-11 METAL CHIP 220K 5% 1/10W R1156 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R1036 1-216-845-11 METAL CHIP 100K 5% 1/10W R1160 1-216-864-11 SHORT CHIP 0
Note : When the L1010 on the DAMP board is replaced,
82
HCD-GT3D
Ver. 1.1
DAMP LCD MIC
R1161 1-216-864-11 SHORT CHIP 0 R3022 1-216-864-11 SHORT CHIP 0
R1163 1-216-864-11 SHORT CHIP 0 R3026 1-216-821-11 METAL CHIP 1K 5% 1/10W
R3028 1-216-821-11 METAL CHIP 1K 5% 1/10W
R1164 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R1165 1-216-832-11 METAL CHIP 8.2K 5% 1/10W R3030 1-216-821-11 METAL CHIP 1K 5% 1/10W
R1166 1-216-827-11 METAL CHIP 3.3K 5% 1/10W R3033 1-216-809-11 METAL CHIP 100 5% 1/10W
R1167 1-216-827-11 METAL CHIP 3.3K 5% 1/10W R3034 1-216-864-11 SHORT CHIP 0
*************************************************************
R1169 1-216-827-11 METAL CHIP 3.3K 5% 1/10W
R1170 1-216-198-91 METAL CHIP 1K 5% 1/8W MIC BOARD
R1171 1-216-198-91 METAL CHIP 1K 5% 1/8W *********
< RELAY > < CAPACITOR >
RY001 1-755-307-21 RELAY C3201 1-124-463-00 ELECT 0.1uF 20% 50V

C3202 1-124-261-00 ELECT 10uF 20% 50V
< TERMINAL > C3203 1-100-756-91 CERAMIC CHIP 0.047uF 10% 50V
C3204 1-126-382-11 ELECT 100uF 20% 16V
TB001 1-780-932-11
TERMINAL BOARD C3206 1-115-872-11 ELECT 2.2uF 20% 50V
(MID/TWEETERS L/R IMPEDANCE USE 2Ω)
************************************************************* * C3207 1-116-720-11 CERAMIC CHIP 10uF 20% 6.3V
LCD BOARD C3210 1-124-463-00 ELECT 0.1uF 20% 50V
********* C3211 1-124-463-00 ELECT 0.1uF 20% 50V
C3215 1-162-925-11 CERAMIC CHIP 68PF 5% 50V
< CAPACITOR >
C3001 1-116-734-11 CERAMIC CHIP 1uF 20% 16V C3218 1-162-963-11 CERAMIC CHIP 680PF 10% 50V
C3011 1-162-919-11 CERAMIC CHIP 22PF 5% 50V C3225 1-126-176-11 ELECT 220uF 20% 10V
C3012 1-162-919-11 CERAMIC CHIP 22PF 5% 50V C3226 1-162-960-11 CERAMIC CHIP 220PF 10% 50V
< CONNECTOR >
CN3000 1-779-550-21 CONNECTOR, FFC (LIF (NON-ZIF)) 13P C3230 1-115-872-11 ELECT 2.2uF 20% 50V
C3231 1-124-257-00 ELECT 2.2uF 20% 50V
< DIODE > C3232 1-115-872-11 ELECT 2.2uF 20% 50V
D3001 6-503-770-11 DI 1L043RW32E0CIE11 (WHITE) C3234 1-118-290-11 CERAMIC CHIP 0.001uF 10% 50V
< IC > C3235 1-118-290-11 CERAMIC CHIP 0.001uF 10% 50V

IC3000 6-600-768-01 IC PNA4823M03S0 ( ) C3237 1-118-290-11 CERAMIC CHIP 0.001uF 10% 50V
IC3004 6-720-239-01 IC BU9795AKS2
< CONNECTOR >
< JUMPER RESISTOR >
CN3200 1-564-720-11 PIN, CONNECTOR (SMALL TYPE) 4P
JR3000 1-216-296-11 SHORT CHIP 0 CN3203 1-822-423-11 CONNECTOR, USB (A) (REC/PLAY 5V 1A)
< LIQUID CRYSTAL DISPLAY > < DIODE >
ND3000 1-812-078-11 LIQUID CRYSTAL DISPLAY D3200 6-502-970-01 DI DZ2J068M0L

D3201 6-502-961-01 DI DA2J10100L
< TRANSISTOR > D3202 6-502-970-01 DI DZ2J068M0L
D3204 6-502-970-01 DI DZ2J068M0L
Q3000 6-552-936-01 TR LTC014EUBFS8TL D3205 6-500-400-01 DIODE BAV99-215
< RESISTOR > D3206 6-500-400-01 DIODE BAV99-215

D3207 6-500-400-01 DIODE BAV99-215
R3000 1-216-809-11 METAL CHIP 100 5% 1/10W D3208 6-500-400-01 DIODE BAV99-215
R3001 1-216-805-11 METAL CHIP 47 5% 1/10W D3209 6-500-400-01 DIODE BAV99-215
R3002 1-216-811-11 METAL CHIP 150 5% 1/10W
R3003 1-216-815-11 METAL CHIP 330 5% 1/10W < FERRITE BEAD >
R3004 1-216-817-11 METAL CHIP 470 5% 1/10W
FB002 1-469-670-21 FERRITE, EMI (SMD) (2012)
R3011 1-216-296-11 SHORT CHIP 0 FB003 1-469-670-21 FERRITE, EMI (SMD) (2012)
Note : When the RY001 on the DAMP board is replaced,
83
HCD-GT3D
Ver. 1.1
MIC MOTHERBOARD
< IC > A-2071-988-AMOTHERBOARD BOARD, COMPLETE
(for SERVICE) (RU)
IC3200 8-759-909-71 IC BA4558F ******************************************
< JACK > < CAPACITOR >
J3200 1-822-967-12 JACK (MIC 1) * C003 1-116-714-11 CERAMIC CHIP 22uF 20% 6.3V
J3201 1-822-967-12 JACK (MIC 2) * C004 1-116-714-11 CERAMIC CHIP 22uF 20% 6.3V
* C005 1-116-714-11 CERAMIC CHIP 22uF 20% 6.3V
< JUMPER RESISTOR > * C006 1-116-714-11 CERAMIC CHIP 22uF 20% 6.3V
JR3200 1-216-296-11 SHORT CHIP 0
JR3201 1-216-864-11 SHORT CHIP 0 C011 1-118-347-11 CERAMIC CHIP 0.1uF 10% 25V
JR3205 1-216-296-11 SHORT CHIP 0
JR3206 1-216-296-11 SHORT CHIP 0 C019 1-116-716-11 CERAMIC CHIP 10uF 10% 16V
JR3207 1-216-296-11 SHORT CHIP 0 C021 1-116-716-11 CERAMIC CHIP 10uF 10% 16V
JR3208 1-216-296-11 SHORT CHIP 0 C024 1-112-797-11 ELECT CHIP 470uF 20% 25V
C030 1-116-716-11 CERAMIC CHIP 10uF 10% 16V
< TRANSISTOR > C032 1-116-716-11 CERAMIC CHIP 10uF 10% 16V
Q3200 6-552-891-01 TR LSAR523UBFS8TL C034 1-118-386-11 CERAMIC CHIP 0.1uF 10% 16V
Q3201 6-552-967-01 TR RHK005N03T146 C035 1-116-734-11 CERAMIC CHIP 1uF 20% 16V
< RESISTOR > C039 1-118-386-11 CERAMIC CHIP 0.1uF 10% 16V
R3200 1-216-857-11 METAL CHIP 1M 5% 1/10W
R3201 1-216-857-11 METAL CHIP 1M 5% 1/10W * C049 1-116-714-11 CERAMIC CHIP 22uF 20% 6.3V
R3202 1-216-817-11 METAL CHIP 470 5% 1/10W * C050 1-116-714-11 CERAMIC CHIP 22uF 20% 6.3V
R3203 1-216-849-11 METAL CHIP 220K 5% 1/10W C051 1-118-361-11 CERAMIC CHIP 0.1uF 10% 50V
R3204 1-216-845-11 METAL CHIP 100K 5% 1/10W * C052 1-116-714-11 CERAMIC CHIP 22uF 20% 6.3V
* C053 1-116-714-11 CERAMIC CHIP 22uF 20% 6.3V
R3205 1-216-809-11 METAL CHIP 100 5% 1/10W
R3206 1-216-827-11 METAL CHIP 3.3K 5% 1/10W C057 1-117-681-11 ELECT CHIP 100uF 20% 16V
R3210 1-216-864-11 SHORT CHIP 0 C064 1-118-347-11 CERAMIC CHIP 0.1uF 10% 25V
R3211 1-216-845-11 METAL CHIP 100K 5% 1/10W * C065 1-118-035-11 CERAMIC CHIP 0.1uF 10% 25V
C066 1-165-492-21 ELECT CHIP 100uF 20% 10V
R3212 1-216-845-11 METAL CHIP 100K 5% 1/10W
R3213 1-216-864-11 SHORT CHIP 0 C067 1-165-492-21 ELECT CHIP 100uF 20% 10V
R3214 1-216-864-11 SHORT CHIP 0 * C068 1-118-035-11 CERAMIC CHIP 0.1uF 10% 25V
R3215 1-216-833-11 METAL CHIP 10K 5% 1/10W C071 1-116-737-11 CERAMIC CHIP 1uF 20% 10V
R3216 1-216-833-11 METAL CHIP 10K 5% 1/10W C072 1-165-492-21 ELECT CHIP 100uF 20% 10V
C073 1-165-492-21 ELECT CHIP 100uF 20% 10V
R3217 1-216-839-11 METAL CHIP 33K 5% 1/10W
R3221 1-216-821-11 METAL CHIP 1K 5% 1/10W C077 1-164-858-11 CERAMIC CHIP 22PF 5% 50V
R3222 1-216-845-11 METAL CHIP 100K 5% 1/10W
R3229 1-216-864-11 SHORT CHIP 0 C080 1-164-858-11 CERAMIC CHIP 22PF 5% 50V
R3230 1-216-864-11 SHORT CHIP 0 C081 1-164-858-11 CERAMIC CHIP 22PF 5% 50V
R3231 1-216-864-11 SHORT CHIP 0 C083 1-118-347-11 CERAMIC CHIP 0.1uF 10% 25V
C084 1-117-681-11 ELECT CHIP 100uF 20% 16V
R3234 1-216-864-11 SHORT CHIP 0
************************************************************* C085 1-118-361-11 CERAMIC CHIP 0.1uF 10% 50V
A-2071-965-A MOTHERBOARD BOARD, COMPLETE C088 1-114-188-11 ELECT CHIP 220uF 20% 16V
(for SERVICE) (AR, LA9) C091 1-118-358-11 CERAMIC CHIP 100PF 1% 50V
A-2071-984-A MOTHERBOARD BOARD, COMPLETE C092 1-118-347-11 CERAMIC CHIP 0.1uF 10% 25V
(for SERVICE) (EA, E4)
A-2071-986-A MOTHERBOARD BOARD, COMPLETE * C100 1-116-738-11 CERAMIC CHIP 1uF 10% 6.3V
(for SERVICE) (AUS) * C101 1-116-738-11 CERAMIC CHIP 1uF 10% 6.3V
A-2071-987-A MOTHERBOARD BOARD, COMPLETE * C102 1-118-035-11 CERAMIC CHIP 0.1uF 10% 25V
(for SERVICE) (MY, TH) C103 1-126-603-11 ELECT CHIP 4.7uF 20% 35V
84
HCD-GT3D
Ver. 1.1
MOTHERBOARD
* C106 1-118-035-11 CERAMIC CHIP 0.1uF 10% 25V * C281 1-118-035-11 CERAMIC CHIP 0.1uF 10% 25V
C109 1-116-737-11 CERAMIC CHIP 1uF 20% 10V C284 1-118-386-11 CERAMIC CHIP 0.1uF 10% 16V
* C113 1-118-035-11 CERAMIC CHIP 0.1uF 10% 25V C298 1-116-737-11 CERAMIC CHIP 1uF 20% 10V
* C114 1-118-035-11 CERAMIC CHIP 0.1uF 10% 25V C299 1-164-874-11 CERAMIC CHIP 100PF 5% 50V
C126 1-164-850-11 CERAMIC CHIP 10PF 0.5PF 50V C316 1-116-717-11 CERAMIC CHIP 10uF 20% 10V
C127 1-164-850-11 CERAMIC CHIP 10PF 0.5PF 50V C319 1-116-717-11 CERAMIC CHIP 10uF 20% 10V
C128 1-116-717-11 CERAMIC CHIP 10uF 20% 10V C321 1-116-717-11 CERAMIC CHIP 10uF 20% 10V
* C129 1-118-035-11 CERAMIC CHIP 0.1uF 10% 25V C322 1-164-850-11 CERAMIC CHIP 10PF 0.5PF 50V
C130 1-164-850-11 CERAMIC CHIP 10PF 0.5PF 50V C323 1-164-852-11 CERAMIC CHIP 12PF 5% 50V
C132 1-164-850-11 CERAMIC CHIP 10PF 0.5PF 50V C325 1-118-459-11 CERAMIC CHIP 0.01uF 10% 25V
C149 1-165-492-21 ELECT CHIP 100uF 20% 10V C346 1-118-459-11 CERAMIC CHIP 0.01uF 10% 25V
* C153 1-118-035-11 CERAMIC CHIP 0.1uF 10% 25V C350 1-128-994-21 ELECT CHIP 47uF 20% 10V
C279 1-164-858-11 CERAMIC CHIP 22PF 5% 50V * C369 1-118-360-11 CERAMIC CHIP 0.1uF 10% 25V
85
HCD-GT3D
Ver. 1.1
MOTHERBOARD
C372 1-116-717-11 CERAMIC CHIP 10uF 20% 10V C626 1-116-865-11 CERAMIC CHIP 10uF 10% 25V
C401 1-165-492-21 ELECT CHIP 100uF 20% 10V * C628 1-116-727-11 CERAMIC CHIP 2.2uF 10% 16V
C420 1-128-403-11 ELECT CHIP 47uF 20% 35V C644 1-164-850-11 CERAMIC CHIP 10PF 0.5PF 50V
C468 1-118-347-11 CERAMIC CHIP 0.1uF 10% 25V C655 1-116-717-11 CERAMIC CHIP 10uF 20% 10V
C577 1-100-588-21 ELECT CHIP 1000uF 20% 6.3V C667 1-118-041-11 CERAMIC CHIP 4.7uF 10% 10V
C603 1-164-936-11 CERAMIC CHIP 680PF 10% 50V C672 1-124-779-00 ELECT CHIP 10uF 20% 16V
C605 1-165-708-11 ELECT CHIP 47uF 20% 6.3V C674 1-118-386-11 CERAMIC CHIP 0.1uF 10% 16V
C608 1-117-949-81 CERAMIC CHIP 820PF 10% 50V C689 1-164-676-11 CERAMIC CHIP 2200PF 5% 16V
C609 1-124-779-00 ELECT CHIP 10uF 20% 16V C690 1-124-779-00 ELECT CHIP 10uF 20% 16V
C614 1-165-708-11 ELECT CHIP 47uF 20% 6.3V C696 1-124-779-00 ELECT CHIP 10uF 20% 16V
* C616 1-118-035-11 CERAMIC CHIP 0.1uF 10% 25V C704 1-124-779-00 ELECT CHIP 10uF 20% 16V
C617 1-118-386-11 CERAMIC CHIP 0.1uF 10% 16V C726 1-128-392-11 ELECT CHIP 470uF 20% 6.3V
C618 1-124-779-00 ELECT CHIP 10uF 20% 16V C742 1-124-779-00 ELECT CHIP 10uF 20% 16V
C619 1-116-707-11 CERAMIC CHIP 47uF 20% 10V C744 1-118-386-11 CERAMIC CHIP 0.1uF 10% 16V
86
HCD-GT3D
Ver. 1.2
MOTHERBOARD
C905 1-165-492-21 ELECT CHIP 100uF 20% 10V < DIODE >
C917 1-116-716-11 CERAMIC CHIP 10uF 10% 16V D102 6-502-961-01 DI DA2J10100L
C922 1-118-386-11 CERAMIC CHIP 0.1uF 10% 16V D401 8-719-069-29 DIODE RB520S-30FJTE61
C928 1-110-530-11 ELECT CHIP 1000uF 20% 6.3V D402 8-719-069-29 DIODE RB520S-30FJTE61
D571 6-502-961-01 DI DA2J10100L
C930 1-164-870-11 CERAMIC CHIP 68PF 5% 50V D572 6-502-961-01 DI DA2J10100L
C933 1-164-850-11 CERAMIC CHIP 10PF 0.5PF 50V
C934 1-118-399-11 CERAMIC CHIP 0.0022uF 10% 50V < FERRITE BEAD >
C935 1-164-840-11 CERAMIC CHIP 1PF 0.25PF 50V FB101 1-481-515-11 BEAD, FERRITE (1608)
C936 1-118-399-11 CERAMIC CHIP 0.0022uF 10% 50V FB115 1-400-851-11 EMI, FERRITE (SMD) (1005)
C937 1-164-840-11 CERAMIC CHIP 1PF 0.25PF 50V FB116 1-400-851-11 EMI, FERRITE (SMD) (1005)
* C938 1-116-720-11 CERAMIC CHIP 10uF 20% 6.3V FB117 1-400-851-11 EMI, FERRITE (SMD) (1005)
* C941 1-116-738-11 CERAMIC CHIP 1uF 10% 6.3V FB320 1-481-348-21 EMI FERRITE (SMD) (1608)
* C943 1-116-738-11 CERAMIC CHIP 1uF 10% 6.3V FB321 1-481-348-21 EMI FERRITE (SMD) (1608)
C944 1-116-734-11 CERAMIC CHIP 1uF 20% 16V FB455 1-481-348-21 EMI FERRITE (SMD) (1608)
C950 1-165-989-91 CERAMIC CHIP 10uF 10% 6.3V < FILTER >
C951 1-164-850-11 CERAMIC CHIP 10PF 0.5PF 50V
FL301 1-234-494-21 FILTER, EMI REMOVAL (SMD)
C952 1-164-852-11 CERAMIC CHIP 12PF 5% 50V FL601 1-234-494-21 FILTER, EMI REMOVAL (SMD)
C954 1-110-563-11 CERAMIC CHIP 0.068uF 10% 16V < IC >
C957 1-164-874-11 CERAMIC CHIP 100PF 5% 50V IC001 (Not supplied) IC TPS542941PWPR
IC002 (Not supplied) IC TPS542941PWPR
C958 1-118-373-11 CERAMIC CHIP 0.01uF 10% 50V IC004 6-721-872-01 IC 78D09AG-TN3-R
C960 1-118-386-11 CERAMIC CHIP 0.1uF 10% 16V IC006 6-721-766-01 IC 78D05AG-TN3-R
C966 1-116-744-11 CERAMIC CHIP 0.22uF 10% 10V IC008 6-719-198-01 IC MM3411A33URE
C980 1-164-933-11 CERAMIC CHIP 220PF 10% 50V IC101 (Not supplied) IC R7S7200032CFP-A
IC102 6-707-866-01 IC TC74VHC126FT (EK)
C982 1-118-047-11 CERAMIC CHIP 10uF 10% 16V IC103 6-719-856-01 IC BU4229F-TR
C983 1-118-047-11 CERAMIC CHIP 10uF 10% 16V IC105 (Not supplied) IC MFI337S3959
C984 1-118-047-11 CERAMIC CHIP 10uF 10% 16V IC106 (Not supplied) IC MX25L3235EM2I-10G
C986 1-124-779-00 ELECT CHIP 10uF 20% 16V
C989 1-118-386-11 CERAMIC CHIP 0.1uF 10% 16V IC301 (Not supplied) IC CXD9990R
IC302 (Not supplied) IC MX25L3235EM2I-10G
C993 1-118-386-11 CERAMIC CHIP 0.1uF 10% 16V IC303 (Not supplied) IC BD00IC0WHFV-GTR
C994 1-118-386-11 CERAMIC CHIP 0.1uF 10% 16V IC304 6-714-351-01 IC R1EX24016ASAS0A
C995 1-118-386-11 CERAMIC CHIP 0.1uF 10% 16V IC305 6-717-694-01 IC BU33TD3WG-TR
C996 1-116-732-11 CERAMIC CHIP 2.2uF 20% 6.3V
C997 1-116-732-11 CERAMIC CHIP 2.2uF 20% 6.3V IC306 6-720-801-01 IC EM638165TSD-6G
IC401 6-720-195-01 IC AM5890S
C998 1-118-386-11 CERAMIC CHIP 0.1uF 10% 16V IC452 6-721-822-01 IC NJM2903CV (TE1)
C1000 1-124-779-00 ELECT CHIP 10uF 20% 16V IC453 6-721-811-01 IC TC7USB40FT
C1001 1-118-403-11 CERAMIC CHIP 0.001uF 10% 50V IC502 6-719-142-01 IC TC62D723FNG
C1003 1-118-403-11 CERAMIC CHIP 0.001uF 10% 50V IC601 8-759-909-71 IC BA4558F
IC602 8-759-596-39 IC SN74LV4052APWR
< CONNECTOR > IC603 8-759-909-71 IC BA4558F
IC604 6-705-973-01 IC PCM1754DBQR
CN001 1-816-296-21 PIN, CONNECTOR (PC BOARD) 9P IC605 8-759-596-39 IC SN74LV4052APWR
CN101 1-844-158-11 PIN, CONNECTOR 5P
(FOR SERVICE USE) IC606 6-710-554-01 IC PCM1808PWR
CN102 1-844-280-11 FFC ST CONNECTOR (NON-ZIF) 10P IC609 6-710-554-01 IC PCM1808PWR
CN118 1-820-123-51 CONNECTOR, FFC/FPC 25P IC615 6-705-973-01 IC PCM1754DBQR
CN119 1-820-117-51 CONNECTOR, FFC/FPC 19P IC901 6-720-187-01 IC NJM41031F1 (TE2)
IC902 6-720-234-01 IC RN5B801-0002
CN302 1-844-191-11 FFC ST CONNECTOR (NON-ZIF) 24P
CN303 1-794-362-51 CONNECTOR, FFC/FPC 5P IC903 6-719-198-01 IC MM3411A33URE
CN401 1-770-470-21 PIN, CONNECTOR (PC BOARD) 6P IC904 6-716-745-01 IC PCM9211PTR
CN517 1-573-290-21 PIN, CONNECTOR (1.5MM) (SMD) 4P IC912 6-707-870-01 IC TC74VHC157FT (EK)
CN601 1-843-888-11 PIN, CONNECTOR (PC BOARD) 4P IC913 8-759-680-48 IC TC7WH157FK
IC914 6-721-848-01 IC PCM5101
CN602 1-794-509-11 PIN, CONNECTOR (PC BOARD) (3P)
CN2002 1-770-160-21 PIN, CONNECTOR (PC BOARD) 2P
(ANTENNA FM)
Note : IC001, IC002, IC101, IC105, IC106, IC301, IC302 and IC303 on the MOTHERBOARD
board cannot exchange with single. When these parts on the MOTHERBOARD board
are damaged, exchange the entire mounted board.
87
HCD-GT3D
Ver. 1.1
MOTHERBOARD
< JACK > < RESISTOR >
J602 1-844-218-11 JACK, PIN 4P R002 1-208-709-11 METAL CHIP 12K 0.50% 1/16W
(AUDIO PARTY CHAIN IN L/R / OUT L/R) R003 1-208-923-11 METAL CHIP 33K 0.50% 1/16W
J907 1-794-970-11 JACK, PIN 1P (VIDEO OUT) R006 1-208-911-11 METAL CHIP 10K 0.50% 1/16W
R020 1-216-864-11 SHORT CHIP 0
< JUMPER > R023 1-218-974-11 METAL CHIP 56K 5% 1/16W
JC001 1-216-295-91 SHORT CHIP 0 R024 1-208-895-81 METAL CHIP 2.2K 0.50% 1/16W
JC002 1-216-295-91 SHORT CHIP 0 R028 1-218-965-11 METAL CHIP 10K 5% 1/16W
JC003 1-216-295-91 SHORT CHIP 0 R029 1-216-843-11 METAL CHIP 68K 5% 1/10W
JC004 1-216-295-91 SHORT CHIP 0 R030 1-218-843-11 METAL CHIP 680 0.50% 1/10W
JC005 1-216-295-91 SHORT CHIP 0 R031 1-208-911-11 METAL CHIP 10K 0.50% 1/16W
JC006 1-216-295-91 SHORT CHIP 0 R033 1-216-827-11 METAL CHIP 3.3K 5% 1/10W
JC007 1-216-295-91 SHORT CHIP 0 R034 1-216-813-11 METAL CHIP 220 5% 1/10W
JC008 1-216-295-91 SHORT CHIP 0 R035 1-216-827-11 METAL CHIP 3.3K 5% 1/10W
R036 1-216-864-11 SHORT CHIP 0
< COIL > R037 1-218-965-11 METAL CHIP 10K 5% 1/16W
L001 1-460-359-11 INDUCTOR 4.7uH R039 1-218-965-11 METAL CHIP 10K 5% 1/16W
L002 1-460-358-11 INDUCTOR 2.2uH R040 1-216-817-11 METAL CHIP 470 5% 1/10W
L003 1-400-789-21 INDUCTOR 2.2uH R041 1-208-709-11 METAL CHIP 12K 0.50% 1/16W
L004 1-400-789-21 INDUCTOR 2.2uH R043 1-208-715-11 METAL CHIP 22K 0.50% 1/16W
L006 1-457-439-11 INDUCTOR 4.7uH R048 1-216-864-11 SHORT CHIP 0

L301 1-400-793-21 INDUCTOR 47uH R053 1-216-864-11 SHORT CHIP 0
L602 1-414-851-21 INDUCTOR 47nH R054 1-216-864-11 SHORT CHIP 0
L603 1-469-187-21 INDUCTOR 68nH R059 1-208-931-11 METAL CHIP 68K 0.50% 1/16W
L604 1-469-187-21 INDUCTOR 68nH R061 1-218-965-11 METAL CHIP 10K 5% 1/16W
L605 1-414-832-11 INDUCTOR 2.2nH R062 1-216-813-11 METAL CHIP 220 5% 1/10W
R063 1-216-864-11 SHORT CHIP 0
< TRANSISTOR > R064 1-216-843-11 METAL CHIP 68K 5% 1/10W
R065 1-216-827-11 METAL CHIP 3.3K 5% 1/10W
Q004 6-553-509-01 TR KTA1542T-RTK/P
Q005 6-553-509-01 TR KTA1542T-RTK/P R066 1-216-827-11 METAL CHIP 3.3K 5% 1/10W
Q006 8-729-054-16 TRANSISTOR KRC402-RTK R080 1-216-864-11 SHORT CHIP 0
Q007 6-553-509-01 TR KTA1542T-RTK/P R085 1-257-604-11 RES-CHIP 47 5% 2W
Q008 6-553-509-01 TR KTA1542T-RTK/P R086 1-216-295-91 SHORT CHIP 0
R087 1-216-295-91 SHORT CHIP 0
Q009 8-729-054-16 TRANSISTOR KRC402-RTK
Q011 6-553-509-01 TR KTA1542T-RTK/P R099 1-216-864-11 SHORT CHIP 0
Q012 8-729-054-16 TRANSISTOR KRC402-RTK R100 1-218-937-11 METAL CHIP 47 5% 1/16W
Q103 6-553-509-01 TR KTA1542T-RTK/P R102 1-218-941-81 METAL CHIP 100 5% 1/16W
Q104 8-729-054-16 TRANSISTOR KRC402-RTK R103 1-218-965-11 METAL CHIP 10K 5% 1/16W
R104 1-218-961-11 METAL CHIP 4.7K 5% 1/16W
Q401 6-551-120-01 TRANSISTOR 2SA2119K R105 1-218-941-81 METAL CHIP 100 5% 1/16W
Q402 6-551-120-01 TRANSISTOR 2SA2119K R106 1-218-965-11 METAL CHIP 10K 5% 1/16W
Q457 6-550-987-01 TR RN1911 R107 1-218-965-11 METAL CHIP 10K 5% 1/16W
Q459 6-553-509-01 TR KTA1542T-RTK/P R108 1-218-965-11 METAL CHIP 10K 5% 1/16W
R109 1-218-957-11 METAL CHIP 2.2K 5% 1/16W
Q571 8-729-054-16 TRANSISTOR KRC402-RTK R110 1-218-977-11 METAL CHIP 100K 5% 1/16W
Q572 6-553-509-01 TR KTA1542T-RTK/P R111 1-218-977-11 METAL CHIP 100K 5% 1/16W
Q574 6-552-967-01 TR RHK005N03T146 R112 1-218-977-11 METAL CHIP 100K 5% 1/16W
Q575 6-552-922-01 TR LTA014EUBFS8TL R113 1-216-864-11 SHORT CHIP 0
R114 1-216-864-11 SHORT CHIP 0
* Q602 6-551-959-01 TR IMX25T110 R115 1-218-953-11 METAL CHIP 1K 5% 1/16W
Q603 6-551-039-01 TRANSISTOR RN4902 (T5RSONY, D, F) R116 1-218-973-11 METAL CHIP 47K 5% 1/16W
Q604 6-550-978-01 TR RN1902 R117 1-218-963-11 METAL CHIP 6.8K 5% 1/16W
Q605 8-729-427-72 TRANSISTOR XP4501 R119 1-218-965-11 METAL CHIP 10K 5% 1/16W
R120 1-218-973-11 METAL CHIP 47K 5% 1/16W
Q606 6-552-922-01 TR LTA014EUBFS8TL
Q607 6-551-039-01 TRANSISTOR RN4902 (T5RSONY, D, F) R122 1-218-990-81 SHORT CHIP 0
Q611 6-550-978-01 TR RN1902 R123 1-218-965-11 METAL CHIP 10K 5% 1/16W
R125 1-218-973-11 METAL CHIP 47K 5% 1/16W
R126 1-218-990-81 SHORT CHIP 0
88
HCD-GT3D
Ver. 1.1
MOTHERBOARD
R127 1-218-965-11 METAL CHIP 10K 5% 1/16W R201 1-218-941-81 METAL CHIP 100 5% 1/16W
R128 1-218-953-11 METAL CHIP 1K 5% 1/16W R202 1-218-965-11 METAL CHIP 10K 5% 1/16W
R163 1-218-990-81 SHORT CHIP 0 R233 1-218-941-81 METAL CHIP 100 5% 1/16W
R172 1-218-941-81 METAL CHIP 100 5% 1/16W R244 1-218-961-11 METAL CHIP 4.7K 5% 1/16W
R188 1-218-989-11 METAL CHIP 1M 5% 1/16W R259 1-218-965-11 METAL CHIP 10K 5% 1/16W
R196 1-250-567-11 METAL CHIP 1M 1% 1/16W R269 1-218-989-11 METAL CHIP 1M 5% 1/16W
89
HCD-GT3D
Ver. 1.1
MOTHERBOARD
R285 1-208-905-11 METAL CHIP 5.6K 0.50% 1/16W R364 1-218-990-81 SHORT CHIP 0
R291 1-218-937-11 METAL CHIP 47 5% 1/16W * R370 1-250-489-11 METAL CHIP 560 1% 1/16W
* R302 1-250-529-11 METAL CHIP 27K 1% 1/16W R381 1-218-965-11 METAL CHIP 10K 5% 1/16W

* R334 1-250-543-11 METAL CHIP 100K 1% 1/16W R421 1-218-941-81 METAL CHIP 100 5% 1/16W
R337 1-216-864-11 SHORT CHIP 0 * R423 1-250-572-11 METAL CHIP 15 1% 1/10W

R343 1-218-959-11 METAL CHIP 3.3K 5% 1/16W * R427 1-250-572-11 METAL CHIP 15 1% 1/10W
R346 1-218-959-11 METAL CHIP 3.3K 5% 1/16W * R430 1-250-572-11 METAL CHIP 15 1% 1/10W
R350 1-218-990-81 SHORT CHIP 0 R463 1-218-958-11 METAL CHIP 2.7K 5% 1/16W
90
HCD-GT3D
Ver. 1.1
MOTHERBOARD
R479 1-218-981-81 METAL CHIP 220K 5% 1/16W R613 1-218-989-11 METAL CHIP 1M 5% 1/16W
R487 1-220-804-11 METAL CHIP 2.2M 5% 1/16W R617 1-218-955-11 METAL CHIP 1.5K 5% 1/16W
R489 1-250-515-11 METAL CHIP 6.8K 1% 1/16W R618 1-218-958-11 METAL CHIP 2.7K 5% 1/16W
R496 1-218-957-11 METAL CHIP 2.2K 5% 1/16W R620 1-218-959-11 METAL CHIP 3.3K 5% 1/16W
R498 1-248-311-11 RES-CHIP 0.1 1% 1/4W R621 1-218-990-81 SHORT CHIP 0

R541 1-216-809-11 METAL CHIP 100 5% 1/10W R634 1-218-989-11 METAL CHIP 1M 5% 1/16W
R567 1-218-935-11 METAL CHIP 33 5% 1/16W R644 1-208-931-11 METAL CHIP 68K 0.50% 1/16W
R571 1-218-981-81 METAL CHIP 220K 5% 1/16W R646 1-218-989-11 METAL CHIP 1M 5% 1/16W
R583 1-248-311-11 RES-CHIP 0.1 1% 1/4W R656 1-218-959-11 METAL CHIP 3.3K 5% 1/16W
R585 1-218-990-81 SHORT CHIP 0 R658 1-218-989-11 METAL CHIP 1M 5% 1/16W
R600 1-208-931-11 METAL CHIP 68K 0.50% 1/16W R666 1-218-973-11 METAL CHIP 47K 5% 1/16W
R605 1-218-989-11 METAL CHIP 1M 5% 1/16W R677 1-218-990-81 SHORT CHIP 0
91
HCD-GT3D
Ver. 1.1
MOTHERBOARD
R692 1-218-969-11 METAL CHIP 22K 5% 1/16W R915 1-208-699-11 METAL CHIP 4.7K 0.50% 1/16W
R693 1-218-989-11 METAL CHIP 1M 5% 1/16W R916 1-208-699-11 METAL CHIP 4.7K 0.50% 1/16W
R720 1-218-929-11 METAL CHIP 10 5% 1/16W R954 1-218-989-11 METAL CHIP 1M 5% 1/16W

R791 1-218-990-81 SHORT CHIP 0
R792 1-216-864-11 SHORT CHIP 0 < COMPOSITION CIRCUIT BLOCK >
R793 1-216-864-11 SHORT CHIP 0
RB301 1-234-370-21 RES, NETWORK 22 (1005X4)
R794 1-216-864-11 SHORT CHIP 0 RB302 1-234-370-21 RES, NETWORK 22 (1005X4)
R795 1-218-929-11 METAL CHIP 10 5% 1/16W RB303 1-234-370-21 RES, NETWORK 22 (1005X4)
R801 1-218-941-81 METAL CHIP 100 5% 1/16W
RB306 1-234-370-21 RES, NETWORK 22 (1005X4)
R820 1-218-929-11 METAL CHIP 10 5% 1/16W
R826 1-218-949-11 METAL CHIP 470 5% 1/16W < THERMISTOR >
R827 1-216-833-11 METAL CHIP 10K 5% 1/10W TH571 1-804-949-11 THERMISTOR, NTC (SMD)
R829 1-218-949-11 METAL CHIP 470 5% 1/16W
R830 1-216-833-11 METAL CHIP 10K 5% 1/10W < VIBRATOR >
R831 1-218-941-81 METAL CHIP 100 5% 1/16W
R835 1-218-929-11 METAL CHIP 10 5% 1/16W X101 1-814-273-11 QUARTZ CRYSTAL UNIT (32.768kHz)
X102 1-814-767-11 QUARTZ CRYSTAL UNITS (13.333MHz)
R836 1-218-929-11 METAL CHIP 10 5% 1/16W X103 1-814-466-11 QUARTZ CRYSTAL UNITS (12.288MHz)
R837 1-218-933-11 METAL CHIP 22 5% 1/16W X104 1-814-356-11 QUARTZ CRYSTAL UNIT (48MHz)
R838 1-218-929-11 METAL CHIP 10 5% 1/16W X301 1-814-023-11 QUARTS CRYSTAL UNIT (27MHz)
R839 1-218-929-11 METAL CHIP 10 5% 1/16W
92
HCD-GT3D
Ver. 1.2
MOTHERBOARD MS-476 OPTICAL SPK_HLED SPLITTER
X600 1-814-365-11 QUARTZ CRYSTAL UNITS (12MHz) 153 1-849-010-11 WIRE (FLAT TYPE) (25 CORE)
X602 1-814-130-11 QUARTZ CRYSTAL UNIT (24.576MHz) * 202 3-703-150-11 CLAMP
************************************************************* 0 203 1-855-006-41 FAN, DC
MS-476 BOARD
************ 0 205 1-844-234-21 AC INLET
0 206 A-2061-350-A SMPS BOARD, COMPLETE
When the MS-476 board is defective, exchange the entire LOADING COMPLETE 211 1-859-087-11 LOUDSPEAKER (20CM)-087-11
ASSY (T). * 213 1-500-082-11 CLAMP, SLEEVE FERRITE (RU, EA, MY, AUS, E4)
************************************************************* 251 1-849-013-11 WIRE (FLAT TYPE) (13 CORE)
OPTICAL BOARD
************* 252 1-849-014-11 WIRE (FLAT TYPE) (10 CORE)
253 1-492-699-11 BLUETOOTH MODULE
< CAPACITOR > 256 1-849-015-11 WIRE (FLAT TYPE) (6 CORE)
257 8-989-602-00 RC-S730 (WW)
C3301 1-127-715-11 CERAMIC CHIP 0.22uF 10% 16V 351 A-1896-391-B LOADING COMPLETE ASSY (T)
C3303 1-127-715-11 CERAMIC CHIP 0.22uF 10% 16V (including MS-476 board)
< IC > 0 354 A-2046-956-A SERVICE, OPTICAL DEVICE(7G)

355 1-469-829-11 CORE, FERRITE
IC3300 6-600-827-01 IC JSR1124 (OPTICAL IN TV) 356 1-849-012-11 WIRE (FLAT TYPE) (24 CORE)
357 1-849-016-11 WIRE (FLAT TYPE) (5 CORE)
< JUMPER RESISTOR >
JR3300 1-216-864-11 SHORT CHIP 0
< RESISTOR >
R3300 1-216-864-11 SHORT CHIP 0

R3301 1-216-864-11 SHORT CHIP 0
*************************************************************
SPK_HLED BOARD
***************
< CONNECTOR >
CN4000 1-580-057-11 PIN, CONNECTOR (SMD) 4P
< DIODE >
D4000 6-504-103-01 DI LA CN5M-GAHA-24-1 (R)

D4001 6-504-102-01 DI LD CN5M-4Q4R-35-1 (B)
D4002 6-504-104-01 DI LT CN5M-GAHB-25-1 (G)
*************************************************************
SPLITTER BOARD
**************
< CONNECTOR >
CN3400 1-820-123-51 CONNECTOR, FFC/FPC 25P

< RESISTOR >
R001 1-216-295-91 SHORT CHIP 0

R002 1-216-295-91 SHORT CHIP 0
R003 1-216-295-91 SHORT CHIP 0
R004 1-216-864-11 SHORT CHIP 0
R005 1-216-864-11 SHORT CHIP 0
R006 1-216-295-91 SHORT CHIP 0

R007 1-216-295-91 SHORT CHIP 0
R008 1-216-295-91 SHORT CHIP 0
*************************************************************
MISCELLANEOUS
**************

Note : If cable, flexible flat and wire (flat type) is replaced,

install it after bending it in the same form as that
before replacement.
93
HCD-GT3D
Ver. 1.2
MEMO
94
HCD-GT3D
REVISION HISTORY
Ver. Date Description of Revision

1.0 2015.02 New
1.1 2015.06 Addition of African, Argentina, Malaysia, Russian, Saudi Arabia and Thai models.
Add note for IC101 in page 5, 39, 48 and 87.
Change description of IC303, IC601 and IC603 in MOTHERBOARD board.
Change description of IC3004 in LCD board.
Change description of IC3200 in MIC board.
Change description of Ref. No. R3137 and R3149 in BUTTON board.
Change description of Ref. No. Q1003, Q1004, Q1014, Q1015, Q1016 and Q1017 in DAMP board.
Change description of Ref. No. C3204 in MIC board.
Change description of Ref. No. C105, C953, Q605, R023, R642 and R649 in MOTHERBOARD board.
Change illustration of CDM in page 13, 20, 74 and 78.
Change note for “BOND FIXATION OF ELECTRIC PARTS” in page 37, 50, 51, 81, 82 and 83.
Change of DAMP, SPK_HLED and SPLITTER boards (Suffix 12).
Change of unit name in SPECIFICATIONS.
Change illustration of IC902 in page 64.
Change P/N of Ref. No. 57 in page 73.
Delete of “MODEL & DEST WRITE MODE” in page 23.
Delete note for “BOND FIXATION OF ELECTRIC PARTS” in page 75.
1.2 2015.08 Add illustration of CORE, FERRITE and CUSHION, SARANET (30X50) on WIRE (FLAT TYPE)
(24 CORE) in page 13, 20, 74, 78 and 79.
Add note of “SCREW TYPE DISCRIMINATION BEFORE DISASSEMBLE THE PANEL, SIDE” in
page 6, 10 and 72.
Add P/N and description for CORE, FERRITE in page 79 and 93.
Add P/N, description and illustration of Ref. No. 1 in page 72.
Change description of disassembly step (1) in page 10.
Change P/N and description of CN101 in MOTHERBOARD board.
Change P/N and description of IC306 in MOTHERBOARD board.
Change P/N and description of D3100 in BUTTON board.
Change P/N and description of D3105 in BUTTON board.
Change P/N and illustration of Ref. No. 57 in page 73.
Change P/N of Ref. No. 2 and 3 in page 72.
Change illustration of PANEL, SIDE (L) ASSY in page 10 and 72.
Change illustration of PANEL, FRONT (SW) ASSY in page 7, 10, 11, 12, 13, 14, 15, 16, 17, 18, 72, 74,
75, 76 and 77.
Delete CN105 in MOTHERBOARD board for Electrical Part List section (Service code changed).
Delete CN451 in MOTHERBOARD board for Electrical Part List section (Service code changed).
Delete CUSHION, WIRE 1.0T on WIRE (FLAT TYPE) (24 CORE) in page 13, 20, 74, 78 and 79.
HCD-GT3D
Ver. Date Description of Revision

Delete four pieces of CUSHION (D-AMP) on SUB CHASSIS in page 15, 16, 75 and 76.
Delete four pieces of CUSHION (SMPS) on CHASSIS in page 17 and 76.
Delete four pieces of CUSHION, BUTTON on CDM section in page 13, 74 and 78.
Delete T CUSHION on PANEL, FRONT (SW) ASSY in page 14, 15, 75 and 77.
Delete HEMILON, 10XLX0.4 in page 13, 74 and 78.
Delete CLAMP, SLEEVE FERRITE for Argentina, Latin-American and Thai models in page 76 and 93.
How to search for a contact point of signal lines or the like in DIAGRAMS SECTION
If a contact point of a BLOCK DIAGRAM, PRINTED WIRING BOARD or SCHEMATIC DIAGRAM is shown in a different page, use
the PDF file search function to find one.
e.g.) If a contact point is shown as , follow the procedure below.

Procedure:
1. Press the [F] key while pressing the [Ctrl] key.
2. Input “>001Z” in the search box and press the [Enter] key.
3. The relevant part (page), where the contact point is shown, appears.
Note: If you still see the original page, press the [Enter] key again.

Sony HCD-GT3D PDF

Uploaded by

Copyright:

Available Formats

Sony HCD-GT3D PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Sony HCD-GT3D PDF

Uploaded by

Copyright:

Available Formats

What are the main components of the audio system?

What are the main components of the audio system?

What are the main specifications of the disc player section?

What are the main specifications of the disc player section?

HCD-GT3D

SERVICE MANUAL Russian Model

Model Name Using Similar Mechanism HCD-GPX555

License and Trademark Notice SAFETY CHECK-OUT

SAFETY-RELATED COMPONENT WARNING!

COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE

1. SERVICING NOTES ............................................. 4 6-30. Schematic Diagram - SPLITTER Board - ...................... 58

2. DISASSEMBLY 7. EXPLODED VIEWS

3. TEST MODE ............................................................ 21

4. ELECTRICAL CHECK ......................................... 26

Flexible Circuit Board Repairing

: LEAD FREE MARK

thermal compound (TIG2000)

NOTE OF DISASSEMBLE THE PANEL, SIDE

For an NFC-compatible smartphone

SCREW TYPE DISCRIMINATION BEFORE DISASSEM-

Type Screw P/N Screw Shape

HOW TO OPEN THE TRAY WHEN POWER SWITCH TURN OFF

8 cm or more 2 Insert the clip etc.

NOTE OF REPLACING THE VOLUME KNOB ASSY OR MIC KNOB

Part No. Description

Apply the lubricant referring to the figure below.

– VOLUME KNOB ASSY – – MIC KNOB ASSY –

CAPACITOR DISCHARGE FOR ELECTRIC SHOCK PREVENTION

SMPS Board (Conductor side view)

2-1. DISASSEMBLY FLOW

2-2. SIDE (L) PANEL, SIDE (R) PANEL

2-3. TOP PANEL SECTION

2-4. OPTICAL BOARD

2-5. LOADING PANEL ASSY

2-6. CDM SECTION

2-8. DAMP BOARD

2-9. MOTHERBOARD BOARD,

2-10. SUB CHASSIS SECTION

2-11. SMPS BOARD

2-13. FRONT PANEL SECTION

2-14. LOUDSPEAKER (20CM)-087-11

Note: Follow the disassembly procedure in the numerical order given.

2-2. SIDE (L) PANEL, SIDE (R) PANEL

1 two screws 3 three claws

5 panel, side (L)

4 Remove the panel, side (L)

5 panel, side (R)

1 two screws (TAPPING (HEX)

2-3. TOP PANEL SECTION

3 two screws (+BVTP 3 × 8) 1 three screws (+BVTP 3 × 8)

F 8 Remove the wires from pin, lead.

9 wire (flat type) (11 core) (CN3402) MIC board

5 one screw (+BVTP 3 × 8)

2-4. OPTICAL BOARD

4 one screw (+BVTP 3 × 8) 1 Remove the wire from pin, lead.

2-5. LOADING PANEL ASSY

4 panel, loading assy

Insert the clip etc. processed to the

8 cm or more 1 Insert the clip etc.

5 Remove the sub chassis section :LUHVHWWLQJ

,QVWDOODWLRQGLUHFWLRQIRUWKHORXGVSHDNHUFP

,QVWDOODWLRQRIZLUHIODWW\SHFRUHDQGZLUHIODWW\SHFRUH