Service Manual: Sound Bar Active Speaker System

HT-X9000F/XF9000 SA-X9000F/XF9000
SERVICE MANUAL US Model

Canadian Model
Ver. 1.0 2018.01 HT-X9000F/SA-X9000F
• All of the units included in the HT-X9000F

AEP Model
(SA-X9000F/SA-WX9000F/Remote
control) or HT-XF9000 (SA-XF9000/SA-
UK Model
WXF9000/Remote control) are required HT-XF9000/SA-XF9000
to confirming operation of SA-X9000F/
XF9000. Check in advance that you have
all of the units.
Note:
Be sure to keep your PC used for service and
checking of this unit always updated with the Photo: SA-X9000F
latest version of your anti-virus software.
In case a virus affected unit was found during
service, contact your Service Headquarters.
COMPONENT MODEL NAME

HT-X9000F HT-XF9000
Bar Speaker (Active Speaker System) SA-X9000F SA-XF9000
Subwoofer (Active Subwoofer) SA-WX9000F SA-WXF9000
• Please refer to service manual separately issued for Subwoofer.
SPECIFICATIONS
Amplifier section USB section Front L/Front R speaker block section
(X9000F: US) (USB) port: Speaker system
Wireless Transmitter/
POWER OUTPUT AND TOTAL HARMONIC Type A (For connecting USB memory) Full Range speaker system, Acoustic Receiver Section
DISTORTION: suspension
(FTC)
BLUETOOTH section Frequency band
Speaker
Communication system 2.4GHz (2.4000GHz - 2.4835GHz)
Front L + Front R: 40mm × 100mm (1 5/8 in. × 4 in) cone
BLUETOOTH Specification version 4.2 Modulation method
With 4ohms loads, both channels type
Output FHSS (Freq Hopping Spread Spectrum)
driven, from 200 - 20,000Hz; rated General
BLUETOOTH Specification Power
35W per channel minimum RMS Power requirements
power, with no more than 1% total
Class1 What’s in the Box
Maximum communication range 120 V AC, 60 Hz (X9000F: US, CND) t#BS4QFBLFS
harmonic distortion from 250mW to 220 V - 240 V AC, 50 Hz/60 Hz

Line of sight approx. 30m 1) t4VCXPPGFS
rated output. (XF9000: AEP, UK)

Maximum number of devices to be t3FNPUFDPOUSPM
POWER OUTPUT (reference) Power consumption

registered t3 TJ[F"""
CBUUFSZ
Front L/Front R speaker blocks: 100W On: 38W

9 devices t)%.*DBCMF TVQQPSUTUIFTQFDJöDBUJPO
(per channel at 4ohms, 1kHz) [Bluetooth Standby] - [On]: Less than
Frequency band equal to Premium High Speed HDMI
(X9000F: CND/XF9000: AEP, UK) 2W
POWER OUTPUT (rated) 2.4 GHz band (2.4GHz - 2.4835GHz) Cable with Ethernet) (1) (X9000F: US, CND)
Modulation method [Bluetooth Standby] - [Off]: Less than t0QUJDBMEJHJUBMDBCMF
9'"&1 6,
Front L + Front R: 60W + 60W 0.5W

(at 4ohms, 1kHz, 1% THD) FHSS (Freq Hopping Spread Spectrum) t8"--.06/55&.1-"5&
Compatible BLUETOOTH profiles 2) Dimensions* (approx.) (w/h/d) t4UBSUVQ(VJEF

POWER OUTPUT (reference) 930mm × 58mm × 85mm (36 5/8 in ×
Front L/Front R speaker blocks: 100W A2DP (Advanced Audio Distribution t0QFSBUJOH*OTUSVDUJPOT
Profile) 2 3/8 in × 3 3/8 in)
(per channel at 4ohms, 1kHz) Design and specifications are subject to
AVRCP (Audio Video Remote Control *Not including projection portion
Inputs Mass (approx.) change without notice.
Profile)
HDMI IN* Supported Codecs 3) 2.5kg (5 33/64 lb)
ANALOG IN SBC 4), AAC 5)
TV IN (OPT) Transmission range (A2DP)
Outputs 20 Hz - 20,000 Hz (Sampling frequency
HDMI OUT (TV (ARC))* 32kHz, 44.1kHz, 48kHz)
1) The actual range will vary depending on
*HDMI IN and HDMI OUT (TV (ARC)) jacks
support HDCP 2.2 protocol. HDCP 2.2 is factors such as obstacles between
newly enhanced copyright protection devices, magnetic fields around a
technology that is used to protect microwave oven, static electricity,
content such as 4K movies. cordless phone use, reception
HT-X9000F/XF9000
sensitivity, the operating system,
HDMI Section software applications, etc.
2)
Connector BLUETOOTH standard profiles indicate
SOUND BAR
Type A (19pin) the purpose of BLUETOOTH
communication between devices.
3)
Codec: Audio signal compression and
conversion format
4) Abbreviation for Subband Codec
5)
Abbreviation for Advanced Audio
Coding SA-X9000F/XF9000
ACTIVE SPEAKER SYSTEM
9-896-483-01
2018A33-1
© 2018.01 Sony Video & Sound Products Inc.
HT-X9000F/XF9000
Copyrights and Trademarks NOTES ON CHIP COMPONENT REPLACEMENT

• Never reuse a disconnected chip component.
This system incorporates Dolby* Digital • Notice that the minus side of a tantalum capacitor may be dam-
and the DTS** Digital Surround System.
aged by heat.
*Manufactured under license from Dolby
Laboratories. Dolby, Dolby Audio, Dolby
Atmos, Dolby Vision, and the double-D SAFETY CHECK-OUT
symbol are trademarks of Dolby After correcting the original service problem, perform the follow-
Laboratories.
ing safety check before releasing the set to the customer:
**For DTS patents, see http://
patents.dts.com. Manufactured under
Check the antenna terminals, metal trim, “metallized” knobs,
license from DTS, Inc. DTS, the Symbol, screws, and all other exposed metal parts for AC leakage.
DTS and the Symbol together, DTS:X, and Check leakage as described below.
the DTS:X logo are registered trademarks
and/or trademarks of DTS, Inc. in the
United States and/or other countries. © LEAKAGE TEST
DTS, Inc. All Rights Reserved. The AC leakage from any exposed metal part to earth ground and
from all exposed metal parts to any exposed metal part having a
The BLUETOOTH ® word mark and logos are
registered trademarks owned by Bluetooth
return to chassis, must not exceed 0.5 mA (500 microamperes.).
SIG, Inc. and any use of such marks by Sony Leakage current can be measured by any one of three methods.
Corporation is under license. Other 1. A commercial leakage tester, such as the Simpson 229 or RCA
trademarks and trade names are those of WT-540A. Follow the manufacturers’ instructions to use these
their respective owners.
instruments.
This system incorporates High-Definition 2. A battery-operated AC milliammeter. The Data Precision 245
Multimedia Interface (HDMI™) technology. digital multimeter is suitable for this job.
The terms HDMI and HDMI High-Definition 3. Measuring the voltage drop across a resistor by means of a
Multimedia Interface, and the HDMI Logo
are trademarks or registered trademarks of VOM or battery-operated AC voltmeter. The “limit” indication
HDMI Licensing Administrator, Inc. in the is 0.75 V, so analog meters must have an accurate low-voltage
United States and other countries. scale. The Simpson 250 and Sanwa SH-63Trd are examples
“BRAVIA” logo is a trademark of Sony
of a passive VOM that is suitable. Nearly all battery operated
Corporation. digital multimeters that have a 2 V AC range are suitable. (See
Fig. A)
“ClearAudio+” is a trademark of Sony
Corporation.
To Exposed Metal
Parts on Set
WALKMAN® and WALKMAN® logo are
registered trademarks of Sony
Corporation.
“PlayStation” is a registered trademark or

trademark of Sony Interactive
Entertainment Inc.
AC
MPEG Layer-3 audio coding technology 0.15 μF 1.5 kΩ voltmeter
and patents licensed from Fraunhofer IIS (0.75 V)
and Thomson.
Windows Media is either a registered

trademark or trademark of Microsoft
Corporation in the United States and/or
other countries. Earth Ground
This product is protected by certain
intellectual property rights of Microsoft Fig. A. Using an AC voltmeter to check AC leakage.
Corporation. Use or distribution of such
technology outside of this product is
prohibited without a license from Microsoft
or an authorized Microsoft subsidiary.
SAFETY-RELATED COMPONENT WARNING!
“DSEE” is a trademark of Sony Corporation.
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE
“TRILUMINOS” and “TRILUMINOS” logo are WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN
a registered trademark of Sony
Corporation.
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS
All other trademarks are trademarks of WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS
their respective owners. MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT

À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0 SUR

LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES
PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONC-
TIONNEMENT. NE REMPLACER CES COMPOSANTS QUE
PAR DES PIÈCES SONY DONT LES NUMÉROS SONT DON-
NÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS
PUBLIÉS PAR SONY.
2
HT-X9000F/XF9000
TABLE OF CONTENTS
1. SERVICING NOTES ............................................. 4 5. DIAGRAMS

5-1. Block Diagram - HDMI Section -................................... 37
2. DISASSEMBLY 5-2. Block Diagram - MAIN Section -................................... 38
2-1. Disassembly Flow ........................................................... 8 5-3. Block Diagram - AMP Section - ..................................... 39
2-2. Top/Bottom Cabinet Block-1 .......................................... 9 5-4. Block Diagram
2-3. Top/Bottom Cabinet Block-2 .......................................... 10 - PANEL/POWER SUPPLY Section - ............................ 40
2-4. SK1 LED Board .............................................................. 11 5-5. Printed Wiring Board - MAIN Board - ........................... 42
2-5. Speaker Connection Cable (L-ch)................................... 12 5-6. Printed Wiring Boards
2-6. Speaker Connection Cable (R-ch) .................................. 13 - SK1-JACK/SK1-WS-CHUKEI Boards - ..................... 43
2-7. Loudspeaker (L-ch/R-ch), Top Cabinet Assy ................. 14 5-7. Schematic Diagram
2-8. Bluetooth Module ........................................................... 14 - SK1-JACK/SK1-WS-CHUKEI Boards - ..................... 43
2-9. Holder (BT) Block .......................................................... 15 5-8. Printed Wiring Board - SK1 AMP Board - ..................... 44
2-10. SK1-WS-CHUKEI Board ............................................... 16 5-9. Schematic Diagram - SK1 AMP Board - ........................ 45
2-11. SK1 IR REP (2) Board .................................................... 17 5-10. Printed Wiring Board - POWER Board -........................ 46
2-12. Main Chassis Block-1 ..................................................... 18 5-11. Schematic Diagram - POWER Board - .......................... 47
2-13. Main Chassis Block-2 ..................................................... 19
2-14. Power-supply Cord ......................................................... 20 6. EXPLODED VIEWS
2-15. MAIN Board-1 ................................................................ 21 6-1. Foot Section .................................................................... 51
2-16. MAIN Board-2 ................................................................ 22 6-2. Top Cabinet Section ........................................................ 52
2-17. SK1 IR REP (1) Board .................................................... 23 6-3. Bottom Cabinet Section .................................................. 53
2-18. SK1-JACK Board ........................................................... 24 6-4. MAIN Board Section ...................................................... 54
2-19. SK1 AMP Board ............................................................. 25 6-5. SK1 AMP Board Section ................................................ 55
2-20. POWER Board ................................................................ 26 6-6. POWER Board Section ................................................... 56
2-21. MAIN Board Service Position ........................................ 26
7. ELECTRICAL PARTS LIST .............................. 57
3. TEST MODE ............................................................ 27
Accessories are given in the last of the electrical parts list.
4. TROUBLESHOOTING .......................................... 31
3
HT-X9000F/XF9000
SECTION 1
SERVICING NOTES
The SERVICING NOTES contains important information for servicing. Be sure to read this section before repairing the unit.
UNLEADED SOLDER ABOUT THE PROTECTION

Boards requiring use of unleaded solder are printed with the lead- All the indicators flash quickly and
free mark (LF) indicating the solder contains no lead. the system is turned off.
(Caution: Some printed circuit boards may not come printed with q Disconnect the AC power cord (mains
the lead free mark due to their particular size) lead) and make sure nothing is
obstructing the ventilation holes of
the system.
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40 °C higher MODEL IDENTIFICATION
than ordinary solder. Distinguish by Part No. and Destination code of the model number
Ordinary soldering irons can be used but the iron tip has to be label on the bottom side of the main unit.
applied to the solder joint for a slightly longer time.
MODEL NUMBER LABEL
Soldering irons using a temperature regulator should be set to
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful!
• Strong viscosity bottom side
Part No.
Unleaded solder is more viscous (sticky, less prone to flow) Destination code
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
front side
also be added to ordinary solder.
NOTE OF REPLACING THE FUSE

The fuse is or could be in the neutral. When a fuse is being re-
placed, the main plug shall be disconnected from the AC outlet to Destination
Destination Part No.
prevent electric shock. code
X9000F: US, CND 4-724-090-0[] UC2
ADVANCE PREPARATION WHEN CONFIRMING OP- XF9000: AEP 4-724-092-0[] CEL
ERATION XF9000: UK 4-724-093-0[] CEK
All of the units included in the HT-X9000F (SA-X9000F/SA- Æ
WX9000F/Remote control) or HT-XF9000 (SA-XF9000/SA-
WXF9000/Remote control) are required to confirming operation DESTINATION ABBREVIATIONS
of SA-WX9000F/WXF9000. Check in advance that you have all The following abbreviations for model destinations are used in this
of the units. service manual.
• Abbreviations
DISCHARGE PROCESSING AEP : European area (Except for UK, Ireland), East European
Before checking the operation of the boards for the electric shock area, CIS area (Moldova) and Middle East area (Israel,
prevention, perform the discharge processing by connecting the Jordan) models
resistor at both ends of the specified capacitor with referring to the CND : Canadian and Latin American area (Puerto Rico) models
figure below. UK : European area (UK and Ireland) model
Note: Be sure to discharge using a resistor of 800  or higher.
– POWER Board (Conductor Side) –
C917
C923
800 :/2 W
800 :/2 W
NOTE OF PERFORMING THE OPERATION CHECK IN

THE STATE THAT HEAT SINK IS REMOVED
When performing the operation check in the state that this unit is
disassembled, it is possible to perform the operation check in the
state that heat sink is removed. However, don’t perform the opera-
tion check in the long time, and perform the operation check in the
volume state as low as possible.
4
HT-X9000F/XF9000
SERIAL NUMBER WRITING WORK WHEN THE MAIN 8. Press the [V]/[v] buttons on the remote commander to select
BOARD REPLACED the “[EDIT]”, and press the [ ] button on the remote com-
When the MAIN board is replaced, be sure to serial number writ- mander. The cursor moves to the right serial number side.
ing work is necessary. Perform works according to the following 9. Press the [V]/[v]/[B]/[b] buttons on the remote commander,
procedure. input the serial number you memoranda in step 1.
Note: For the serial number writing work, need a TV monitor compatible
with resolution “1920 × 1080 P” of video format. Operation:
[B]/[b] Select the digit to edit
Serial number writing procedure: [V]/[v] Make the selected number to +1/–1
1. Take a memorandum of the serial number on the bottom of this
unit. 10. Press the [ ] button on the remote commander, return to the
cursor position [EDIT].
Serial number position
11. Press the [V]/[v] buttons on the remote commander to select
the “[SAVE]”.
12. Press the [ ] button on the remote commander, the message
bottom side “>OK” is appear and serial number is written.
Serial number (7 digit)
Serial number Editor
[EDIT] [1234567]
[CLEAR]
[SAVE]
> OK
front side
2. Connect this unit with TV monitor.

3. Touch the [1] button to turn the power on.
4. Press button on the remote commander in order of the follow- (Displayed characters in the above figure are example)
ing.
[AUTO SOUND] → [DISPLAY] → [.] → [V] 13. Press the [BACK] button on the remote commander, return to
(Make the interval when each button is pressed within one sec- the service mode menu screen.
ond) 14. Press the [V]/[v] buttons on the remote commander to select
5. The LEDs light up/flash on this unit as shown in the following the “Exit”.
figure, then enter the service mode to display the service mode
menu on TV monitor. Service diag [ver x.xx.xx]
System Information
The all LEDs light up. The all LEDs keep flash. Exit
TV monitor screen
Service diag [ver x.xx.xx]
System Information
Exit
15. Press the [ ] button on the remote commander, the service

mode is released and turn the power off automatically.
6. Press the [V]/[v] buttons on the remote commander to select

the “Serial number Editor”.
7. Press the [ ] button on the remote commander, display the se-
rial number editor screen.

[EDIT] [XXXXXXX]
[CLEAR]
[SAVE] Serial
number
(Displayed characters in the above figure are example)
5
HT-X9000F/XF9000
WIRELESS CONNECTION (LINK) WORK OF BAR SPEAK- What to do if only bar speaker or subwoofer are brought
ER AND SUBWOOFER in for repair
When the Bluetooth module of bar speaker or Bluetooth module of If only the bar speaker or subwoofer is brought in for repair situa-
subwoofer are replaced, the wireless connection (LINK) of the bar tion, and the Bluetooth module is replaced, by customer must wire-
speaker and subwoofer will be disconnected. less connection (LINK) the bar speaker and subwoofer.
Before returning repaired products to the customer, follow the pro-
cedure below to LINK the bar speaker and subwoofer. • If the customer was not performing the secure link
Note: If only the bar speaker or subwoofer is brought in for repair, wire- It will automatically wireless connection (LINK) with the bar
less connection (LINK) is not possible. Refer to “What to do if only speaker and subwoofer when turn the power on.
bar speaker or subwoofer are brought in for repair”.
• If the customer was performing the secure link
Replacing parts for repairing that required wireless con- The customer must need perform the secure link setting again, or
nection (LINK) customer must need to cancel the secure link of the bar speaker or
• Replacing the Bluetooth module of bar speaker subwoofer at hand of the customer and perform a normal wireless
• Replacing the Bluetooth module of subwoofer connection.
Wireless connection (LINK) method Secure link cancellation method of bar speaker
When the repairing unit is not secure link: Procedure:
After replacing the Bluetooth module of the bar speaker or replac- 1. Connect bar speaker with TV monitor.
ing the Bluetooth module of the subwoofer, when turn the power 2. Press the [1] button to turn the power on.
on, it will automatically wireless connection. 3. Press the [HOME] button on the remote commander.
4. From the display of home menu on the TV monitor, operate
When the repairing unit was secure link: and decision in the following order.
After replacing the Bluetooth module of the bar speaker or replac- “Setup” → “Advanced settings” → “Speaker settings” → “Se-
ing the Bluetooth module of the subwoofer, even if turn the power cure Link”
on, if you do not automatically wireless connection, there is a pos- 5. Since the “On/Off” switching of Secure Link is displayed, se-
sibility that the repairing unit was secure link. lect the “Off” and decision.
In this case, perform the secure link according to “Secure link
method” below. Secure link cancellation method of subwoofer
Also, press and hold the [LINK] button on the rear side of sub- Procedure:
woofer to cancel the secure link, it can automatically wireless con- 1. Press the [1] button on the rear side of subwoofer to turn the
nection. power on.
2. Press and hold the [LINK] button on the rear side of subwoof-
Secure link method er.
Procedure:
1. Connect bar speaker with TV monitor.
2. Press the [1] button on the bar speaker to turn the power on.
3. Press the [1] button on the rear side of subwoofer to turn the
power on.
4. Press the [HOME] button on the remote commander. Press and hold the [LINK] button.
5. From the display of home menu on the TV monitor, operate
and decision in the following order.
“Setup” → “Advanced settings” → “Speaker settings” → “Se-
cure Link”→ “On”
6. Press the [LINK] button on the rear side of subwoofer.
Note: Perform the next step within 2 minutes after the power indicator is
flashed.
7. From the display of home menu on the TV monitor, select the
“Start” and decision.
8. The message “Finish” is displayed on the TV monitor, the
power indicator of the subwoofer is lit in orange and secure
link is completed. 3. When the secure link is canceled, the power indicator is flashes
in green.
6
HT-X9000F/XF9000
Æ
RESETTING THE SYSTEM SPREADING OF COMPOUND

1 Press HOME.
When the IC6006 on the SK1 AMP board or the SK1 AMP board
The home menu appears on the TV is replaced, spread the compound to the touching portion between
screen. the IC6006 and the heat sink.
2 Select [Setup] - [Advanced
Settings] on the home menu.
– SK1 AMP Board (Side A) –
3 Select [Resetting].
4 Select the menu item you want to

reset.
5 Select [Start].
IC6006
To cancel resetting
Select [Cancel] in step 5.
compound
If You Cannot Perform
Resetting Using the Home
Menu
Press and hold Æ (power) and –
(volume) on the main unit for more
than 5 seconds.
The settings return to their initial MALFUNCTION PREVENTION OF THE BUTTON (TOUCH
status.
PANEL SWITCH)
Note: By perform resetting, the link with the subwoofer may be lost. In When the button portion on the top side of the main unit are
this case, refer to “WIRELESS CONNECTION (LINK) WORK OF touched with something such as the floor surface, there is a pos-
BAR SPEAKER AND SUBWOOFER” on page 6.
sibility of occurring the malfunction.
When performing the operation check in the state that the top side
ADVANCE CONFIRMATION WHEN SOUND IS NOT on this unit is under, set the stand etc. to the position that avoids the
OUTPUTTED, OR WHEN THE SUBWOOFER IS NOT button portion as shown in the figure below, perform in the state
LINKED that the button portion does not touch anything.
If in the symptoms such as not sound outputted of ARC, or the
subwoofer is not linked, be sure to refer to the TROUBLESHOOT-
ING below before repairing.
bottom side
When the sound is not outputted of ARC:
Refer to “The sound is not outputted of ARC” on the TROUBLE-
SHOOTING (page 34). stand button portion
When the subwoofer is not linked:
stand
Refer to “The subwoofer is not linked” on the TROUBLESHOOT-
ING (page 35).
FLEXIBLE FLAT CABLE FOR EXTENSION
NOTE OF REPLACING THE SK1 TOUCH, SK1 LED, If it necessary to the long flexible flat cable connecting the MAIN
SK1 IR REP (1) OR SK1 IR REP (2) BOARDS FOR board (CN701) and the SK1 AMP board (CN6005), use the follow-
REPAIRING ing flexible flat cable.
When the SK1 TOUCH, SK1 LED, SK1 IR REP (1) or SK1 IR
REP (2) boards are defective, replace the complete mounted board Part No. Description
or the whole parts including the applicable board. 1-912-603-11 FLEXIBLE FLAT CABLE (MB~AMP)
The mounted parts cannot be replaced with single for repairing. (28 CORE) (Length: 330 mm)
NOTE OF REPLACING THE MAIN BOARD FOR RE-

PAIRING
When the MAIN board is defective, replace the complete mounted
board.
The mounted parts cannot be replaced with single for repairing.
Block diagram and printed wiring board are described for refer-
ence purposes in this service manual.
Also, after replacing the MAIN board please refer to “SERIAL
NUMBER WRITING WORK WHEN MAIN BOARD RE-
PLACED” on page 5.
NOTE OF REPLACING THE ELECTRICAL PARTS ON

EACH BOARDS FOR REPAIRING
Among mounted electrical parts on each boards, only parts that
are described in the electrical parts list can be replaced for repair.
The parts that are not described in the electrical parts list cannot be
replaced with single for repairing.
7
HT-X9000F/XF9000
SECTION 2
DISASSEMBLY
• This set can be disassembled in the order shown below.
2-1. DISASSEMBLY FLOW
SET
2-2. TOP/BOTTOM CABINET BLOCK-1 2-21. MAIN BOARD SERVICE POSITION

(Page 9) (Page 26)
2-3. TOP/BOTTOM CABINET BLOCK-2 Top cabinet block

(Page 10)
Bottom cabinet block
2-9. HOLDER (BT) BLOCK 2-8. BLUETOOTH MODULE 2-4. SK1 LED BOARD
(Page 15) (Page 14) (Page 11)
2-10. SK1-WS-CHUKEI BOARD

(Page 16)
2-5. SPEAKER CONNECTION 2-6. SPEAKER CONNECTION
CABLE (L-ch) CABLE (R-ch)
2-11. SK1 IR REP (2) BOARD (Page 12) (Page 13)
(Page 17)
2-12. MAIN CHASSIS BLOCK-1 2-7. LOUDSPEAKER (L-ch/R-ch),

(Page 18) TOP CABINET ASSY
(Page 14)
2-13. MAIN CHASSIS BLOCK-2

(Page 19)
2-14. POWER-SUPPLY CORD 2-15. MAIN BOARD-1

(Page 20) (Page 21)
2-16. MAIN BOARD-2

(Page 22)
2-17. SK1 IR REP (1) BOARD

(Page 23)
2-18. SK1-JACK BOARD 2-19. SK1 AMP BOARD 2-20. POWER BOARD
8
HT-X9000F/XF9000
Note: Follow the disassembly procedure in the numerical order given.
2-2. TOP/BOTTOM CABINET BLOCK-1

• Continued on 2-3 (page 10).
1 eight screws
(BVTP3 u 10)
left side
2 two screws
(BVTP3 u 6)
front side
top side
1 ten screws
(BVTP3 u 10)
top side
right side rear side
Turn over.
soft cloth, etc.

front side right side
3 Lift up the top cabinet
block in the direction
of the arrow.
top cabinet block

rear side
4 Remove the top cabinet block

in the direction of the arrow.
3 Lift up the top cabinet left side

of the arrow.
+RZWRLQVWDOOWKHWRSFDELQHWEORFN
Attach in order from 1 to 6.
1 First install the front side of the top

cabinet block as shown below.
top cabinet block
front side
Note: Install the top cabinet block on the left and right at the same time.
The figures below explain using illustrations of the left side.
2 Open to the outer side with your

5 Slowly lower the top cabinet 6 Push the top cabinet
fingers so that the corner of the
block straight down. block.
left side top cabinet block does not touch.
top cabinet block Push.
3 Install the top cabinet
of the arrow.
4 Check.
bottom cabinet block
9
HT-X9000F/XF9000
2-3. TOP/BOTTOM CABINET BLOCK-2
soft cloth, etc.

1 Open the top cabinet block
right side
top cabinet block
rear side
2 FFC (16P)
(CN3004) left side
(See Fig. A)
5 top cabinet block
4 speaker connection cable

connector (CN6003)
(See Fig. B)

connector (CN6004)
(See Fig. B)
6 bottom cabinet block
:LUHVHWWLQJ
< Fig. A > < Fig. B > speaker connection speaker connection
MAIN board cable [red/black] cable [gray/black]
–7RSYLHZ– (for R-ch) (for L-ch)
FFC (16P)
front side –7RSYLHZ–
NG
The FFC (16P) must not
touch the heatsink main.
FFC (16P)
heatsink CN3004 terminal

main side
SK1 AMP board Bend. Bend.

heatsink main
CN6003 CN6004
10
HT-X9000F/XF9000
2-4. SK1 LED BOARD
&DEOHDUUDQJHPHQWZKHQLQVWDOOLQJWKH6./('ERDUGEORFN
Install the SK1 LED board on top of the speaker connection cable while holding down
the connector with your fingers so that the speaker connection cable does not rise.
Note 1: Check that the speaker connection

front side cable is in the two grooves. SK1 LED board
Hold down. Hold down.

SK1-TOUCH board
–%RWWRPYLHZ–
4 FFC (16P)
(CN1302)
(See Fig. C)
left side hole 2 two screws
hole (BVTP3 u 8)
5 SK1 LED board

Note 2: When installing the SK1 LED board,
A align the two bosses and two holes.
boss 3 Remove the SK1 LED board block

soft cloth, etc. boss
front side
+RZWRLQVWDOOWKH))&3 A 1 FFC (6P)

)LJ&! (CN1306)
FFC (16P)
front side top cabinet block

short top side
long
CN1302
))&3VHWWLQJ
The opposite side SK1 LED board The opposite side
SK1 LED board
is terminal side. is terminal side.
CN1306
right side
front side
FFC (6P)
–%RWWRPYLHZ–
SK1-TOUCH board
11
HT-X9000F/XF9000
2-5. SPEAKER CONNECTION CABLE (L-ch)

2 terminal (wide)
[gray]
1 Draw the speaker connection
2 terminal (narrow) cable out of two grooves.
[black]
1 Draw the speaker connection

cable out of two grooves.
left side

[gray/black] (for L-ch)
soft cloth, etc.

front side
top cabinet block
:LUHVHWWLQJ
Note 1: When pressing the speaker connection cable
into the grooves, set the wire as shown below.
top side
speaker connection cable

right side
+RZWRLQVWDOOWKHVSHDNHUFRQQHFWLRQFDEOHIRU/FK
front side
loudspeaker
(for L-ch) two grooves two grooves
left side right side
–%RWWRPYLHZ–
&DEOHFRQQHFWRUVHWWLQJ
,QVWDOODWLRQGLUHFWLRQIRUWKHWHUPLQDOV Note 3: When installing the speaker connection cable,
Note 2: When connecting the terminals of the speaker connection set the position and orientation of the connector
cable to the loudspeaker, be careful of the direction of the as shown below.
terminals.
loudspeaker (for L-ch) right side
front side terminal (wide)
OK [gray]
terminal (narrow) guide line

NG [black]
'LUHFWLRQIRUWKHFRQQHFWRU
OK OK NG
NG
12
HT-X9000F/XF9000
2-6. SPEAKER CONNECTION CABLE (R-ch)

left side top cabinet block
3 speaker connection cable 1 Draw the speaker connection

[red/black] (for R-ch) cable out of two grooves.
(See Fig. D)
2 terminal (narrow)
front side [black]
2 terminal (wide)
[red]
top side
1 Draw the speaker
connection cable out
:LUHVHWWLQJ of three grooves.
Note 1: When pressing the speaker connection
cable into the grooves, set the wire as
shown below.

soft cloth, etc.
right side
+RZWRLQVWDOOWKHVSHDNHUFRQQHFWLRQFDEOHIRU5FK
)LJ'!
front side two three
grooves grooves loudspeaker (for R-ch)
–%RWWRPYLHZ–
&DEOHFRQQHFWRUVHWWLQJ ,QVWDOODWLRQGLUHFWLRQIRUWKHWHUPLQDOV
Note 3: When installing the speaker connection cable, Note 2: When connecting the terminals of the speaker
set the position and orientation of the connector connection cable to the loudspeaker, be careful
as shown below. of the direction of the terminals.
terminal (narrow)
[black]
left side front side loudspeaker (for R-ch)
terminal (wide)
[red]
guide line
OK
OK
'LUHFWLRQIRUWKHFRQQHFWRU
OK NG NG
NG
13
HT-X9000F/XF9000
2-7. LOUDSPEAKER (L-ch/R-ch), TOP CABINET ASSY

boss
left side 5 indicator (LED)
boss hole Note 2: When installing the indicator (LED),
front side align the two bosses and two holes.
1 two screws
(BVTP3 u 10)
SK1-TOUCH
hole board
2 4 hole
boss
boss
hole
7 top cabinet assy
1 two screws (Including SK1-TOUCH board)
(BVTP3 u 10) top side
3 loudspeaker (for L-ch)
Note 1: When installing the loudspeaker (for L-ch),
align the two bosses and two holes. boss
,QVWDOODWLRQGLUHFWLRQIRUWKHORXGVSHDNHUIRU/FK boss

Note 3: When installing the loudspeaker, make the position
of terminals as shown in the figure below. 6 FFC (6P)
terminals position (CN1901) hole
terminal
2
left side top side side hole
1 two screws right side

(BVTP3 u 10) soft cloth, etc.
– Inner view – 3 loudspeaker (for R-ch)

Note 1: When installing the loudspeaker
(for R-ch), align the two bosses
,QVWDOODWLRQGLUHFWLRQIRUWKHORXGVSHDNHUIRU5FK
and two holes.
Note 3: When installing the loudspeaker, make the position
of terminals as shown in the figure below. 1 two screws
(BVTP3 u 10)
terminals position
top side
right side
– Inner view –
2-8. BLUETOOTH MODULE

Note: When the bluetooth module is replaced, be 2 screw
sure to refer to “WIRELESS CONNEC- (BVTP3 u 8)
TION (LINK) WORK OF BAR SPEAK- 1 Draw the FFC (18P)
ER AND SUBWOOFER” on page 6. 4 bluetooth module out of the connector.
terminal
side
3
catcher
catcher
top side
front side
bottom cabinet block right side
14
HT-X9000F/XF9000
2-9. HOLDER (BT) BLOCK
))&3VHWWLQJ

holder (BT) block FFC (18P)
CN1502
holder (BT) block

terminal
side CN1502
Pass the FFC (18P) underneath
rear side
right side the holder (BT) block.
SK1-WS-CHUKEI board
2 two screws
(BVTP3 u 8)
2 screw
(BVTP3 u 8)
hole
5 holder (BT) block

3 Lift up the holder (BT) block Note: When installing the holder (BT) block,
in the direction of the arrow. hole align the two bosses and two holes.
top side 4 FFC (18P)

(CN1502)
terminal
side
1 Turn over the end of the

cushion (absorbent).
front side
boss
boss
right side
15
HT-X9000F/XF9000
2-10. SK1-WS-CHUKEI BOARD
:LUHVHWWLQJ
OK NG
Gap. (Do not touch No gap. (Touch
the shield main.) the shield main.)
shield shield
Gap.
main main
packing (CZ2)
screw boss
groove groove groove screw boss

–7RSYLHZ– screw boss groove groove
CN1501
CN702
left side
right side
Twist the MAIN board Pass the MAIN board cable SK1-WS-CHUKEI board
cable two times. beside the screw boss. front side
4 MAIN board cable 2 packing (CZ2)

connector (CN702)
5 screw
(BVTP3 u 8)
top side
1 MAIN board cable
connector (CN1501)
5 screw
(BVTP3 u 8)
6 SK1-WS-CHUKEI board
Note: When installing the SK1-WS-CHUKEI
hole board, align the two bosses and two holes.
hole
front side
3 Draw the MAIN board cable

out of two grooves.
3 Draw the MAIN board cable boss

out of three grooves. boss
right side
16
HT-X9000F/XF9000
:LUHVHWWLQJ catcher rear side catcher

catcher catcher SK1 IR REP (2) board
–7RSYLHZ–
CN1101
4 SK1 IR REP board cable

connector (CN1101)
top side
2 screw
(BVTP3 u 10)
5 SK1 IR REP (2) board

Note: When installing the SK1 IR REP (2) board,
align the hole and groove with the two bosses.
hole
groove
3 Lift up the SK1 IR REP (2) board
block in the direction of the arrow.
boss
front side
1 Draw the SK1 IR REP board bottom cabinet block

cable out of two catchers.
1 Draw the SK1 IR REP board

cable out of two catchers.
boss
right side
17
HT-X9000F/XF9000

top side
left side
1 six screws
(BVTP3 u 10)
front side
right side
Note about installing the main chassis block

IR repeater portion
(SK1 IR REP (1) board) hole
3 Draw the IR repeater portion out
of the hole in bottom cabinet.
IR repeater portion
hole
front side – Top view –

MAIN board
4 main chassis block

Note: When installing the main chassis
block, align the boss and hole.
boss
2 Lift up the main chassis block hole

18
HT-X9000F/XF9000

1 four screws
(BVTP3 u 8) 2 insulator top
hole
Note: When installing the insulator top,
align the four ribs and four holes.
1 screw
(BVTP3 u 8) 1 screw
(BVTP3 u 8)
1 screw
(BVTP3 u 8)
hole left side
hole
hole
1 screw
(BVTP3 u 8)
rib top side
front side
rib
rib
rib
right side
3 power-supply cord
connector (CN901)
4 Draw the power-supply

cable out of catcher.
cord bushing
6 main chassis block
groove
catcher
5 Draw the cord bushing

portion out of groove.
3RZHUVXSSO\FRUGEORFNVHWWLQJ
claw side
[white]: US, CND
–7RSYLHZ– lock side POWER board [blue]: AEP, UK
cord bushing
CN901
right side
[black]: US, CND

power-supply
[brown]: AEP, UK
cord
power-supply cord catcher
two claws
19
HT-X9000F/XF9000
2-14. POWER-SUPPLY CORD

bottom cabinet block right side
top side
front side
left side 1 Unlock.
2 cord bushing
(FBS001)
,QVWDOODWLRQSRVLWLRQRIWKHFRUGEXVKLQJ)%6
cord bushing (FBS001)

power-supply cord
to POWER board
80 ± 5 mm
lock side
4 power-supply
cord
3 Draw the power-supply cord out

of the hole in bottom cabinet.
hole
20
HT-X9000F/XF9000
2-15. MAIN BOARD-1

2 shield main block

Note: When installing the shield main block,
align the hole and groove with the two ribs.
1 screw 1 two screws
(BVTP3 u 8) (BVTP3 u 8)
3DVWLQJSRVLWLRQRIWKHVKHHWUDGLDWLRQ
1 four screws )LJ(!
(BVTP3 u 8) sheet radiation sheet radiation
(8.0 u 8.0 mm) IC101 (34.0 u 16.0 mm)
hole
IC2302
sheet radiation
(14.0 u 14.0 mm)
left side
groove
4 sheet radiation
5 sheet
(14.0 u 14.0 mm)
radiation
(See Fig. E)
(34.0 u 16.0 mm)
1 screw (See Fig. E) MAIN board
guide line IC103 –7RSYLHZ– IC102
(BVTP3 u 8)
left side
5 sheet radiation
(34.0 u 16.0 mm)
(See Fig. E)
rib
front side top side
3 sheet radiation
main chassis block
(8.0 u 8.0 mm)
(See Fig. E) rib
right side
:LUHVHWWLQJ rear side
–7RSYLHZ– CN303 POWER board

7 SK1-JACK board cable
connector (CN532)
Press.
8 SK1-JACK board cable
connector (CN7001) Press.
6 flexible flat cable (28P)
(CN701)
terminal side
0 SK1 AMP board
cable connector
(CN303)
Press.
MAIN board
9 SK1 IR REP board

cable connector
(CN302)
qa POWER board cable

connector (CN301)
21
HT-X9000F/XF9000
2-16. MAIN BOARD-2
Note 1: When the MAIN board is replaced, be sure to refer to “SE-

RIAL NUMBER WRITING WORK WHEN THE MAIN
BOARD REPLACED” on page 5.
B
6 MAIN board block
Note 2: When installing the MAIN board block,
align the hole and groove with the two ribs.
hole
1 screw
5
(B3 u 5)
1 screw groove
(B3 u 5)
left side
rib top side
3 Move the SK1-JACK board

cable to the outer side. main chassis block
2 Move the FFC (28P) rib

to the outer side.
4 Move the SK1 IR REP board

cable to the outer side. front side
right side
Turn over. Note 3: When the MAIN board block is removed from
the main chassis block, the shield (pana) and
radio wave absorption sheet will detach from
the MAIN board.
When assembling, remove the shield (pana)
and radio wave absorption sheet from the main
chassis block, and install them onto the MAIN 1RWHDERXWLQVWDOOLQJWKHVKLHOGSDQD
board.
OK
7 shield (pana) Touching.
Note 4: When installing the shield (pana),
align the rib and hole.
NG NG
rib Missing. No touching.
8 radio wave absorption front side

sheet
9 gasket (SL) MAIN board two on-board clips
9 gasket (SL) shield (pana)
two on-board
hole clips
left side 0 MAIN board
left side
two on-board clips

two on-board clips two on-board clips
22
HT-X9000F/XF9000
6FUHZSRVLWLRQ
–7RSYLHZ– rear side
1 screw
(BVTP3 u 8)
1 three screws
(BVTP3 u 8)
screw
(BVTP3 u 8)
SK1 IR REP (1) board
7 screw
hole (BVTP3 u 8)
hole groove hole

hole
8 SK1 IR REP (1) board
5 sheet radiation
1 three screws Note 2: When installing the SK1 IR
(BVTP3 u 8) REP (1) board, align the hole
C and groove with the two ribs.
2 Draw the SK1-JACK C
board cable out of 6 connector rib
the hole. rib
(CN1101)
left side rib

4 bracket main block
Note 1: When installing the bracket
main block, align the hole
and groove with the two ribs.
rib
3 Draw the FFC (28P) bracket main block
out of the hole.
top side
main chassis block
groove
front side
right side
6.,55(3ERDUGFDEOHVHWWLQJ
Attach in order from 1 to 4. 1 Pass the SK1 IR REP board
cable through the hole.
SK1 IR REP (1) board –7RSYLHZ–
SK1 IR REP board cable
left side
front side
bracket main block

hole
Turn over.
front side SK1 IR REP board cable
SK1 IR REP (1) board
left side
–%RWWRPYLHZ–
3 catcher 2 CN1101
4 two catchers
23
HT-X9000F/XF9000
2-18. SK1-JACK BOARD
2 two screws 1 SK1-JACK board cable

(BVTP3 u 8) connector (CN1601)
left side 2 screw

(BVTP3 u 8)
top side
1RWHDERXWLQVWDOOLQJWKH6.-$&.ERDUG
)LJ)!
–6LGHYLHZ– top side
main chassis block
front side
right side
Check that the jack and two connectors are installed

on the holes of the chassis correctly.
4 Draw the jack and two connectors
out of the three holes in chassis.
,QVWDOODWLRQSRVLWLRQRIWKH6.-$&.ERDUG
Note: When installing the SK1-JACK board,
align the two holes and groove with 5 SK1-JACK board
the three ribs. (See Fig. F)
–7RSYLHZ– rib hole
left side
3 Remove the SK1-JACK board
groove
hole
rib hole
hole
chassis
rib hole
SK1-JACK board
24
HT-X9000F/XF9000
2-19. SK1 AMP BOARD
Note 1: When the SK1 AMP board is replaced, spread the compound
to the touching portion between the IC6006 and the heat sink.
4 two screws
(BVTP3 u 10)
5 heatsink
Note 2: When installing the heatsink, align
boss the two bosses and two holes.
boss
1 flexible flat cable (28P)
(CN6005)
6 screw
terminal side
6 screw (BVTP3 u 8)
(BVTP3 u 8)
hole
hole
6 screw
(BVTP3 u 8) hole
8 SK1 AMP board
2 SK1 AMP board cable
Note 3: When installing the SK1 AMP board,
connector (CN6001)
align the two ribs and two holes.
7 hole
9 sheet radiation
(14.0 u 10.0 mm)
9 sheet radiation
(14.0 u 10.0 mm) 9 sheet radiation
(14.0 u 10.0 mm)
left side
9 sheet radiation
(14.0 u 10.0 mm)
3 POWER board cable
connector (CN6002)
main chassis block
rib
top side
rib
:LUHVHWWLQJUHIHUHQFH
rear side
–7RSYLHZ– CN6001 POWER board front side
right side
Press.
Press.
Press.
MAIN board CN6002 SK1 AMP board
25
HT-X9000F/XF9000
2-20. POWER BOARD

2 two screws
(BVTP3 u 8)
5 POWER board
2 screw Note: When installing the POWER board,
(BVTP3 u 8) align the two ribs and two holes.
4 Draw the corner of POWER

1 POWER board cable board out of the slit.
connector (CN6002)
hole
:LUHVHWWLQJUHIHUHQFH
rear side
left side
hole –7RSYLHZ– CN6001 POWER board
top side
Press.
Press.
front side
slit
main chassis block
rib Press.
3 Remove the POWER board right side MAIN board CN6002 SK1 AMP board
in the direction of the arrow. rib
2-21. MAIN BOARD SERVICE POSITION
Note: The service position below cannot be performed with the flex-
ible flat cable (L = 60 mm) used with the unit.
Refer to “FLEXIBLE FLAT CABLE FOR THE EXTENSION”
on page 7, and use a long flexible flat cable (L = 330 mm).

left side
insulating sheet
flexible flat cable (28P)
(L = 330 mm)
(See Note)
SK1 AMP board
top cabinet block

POWER board
SK1-JACK board
rear side
MAIN board bluetooth module
SK1-TOUCH board
SK1-WS-CHUKEI board right side
SK1 LED board
26
HT-X9000F/XF9000
SECTION 3
TEST MODE
Button and LED position: Initial setting for demo mode:
• Cannot power off by the [1] button (both the main unit and the
Button position remote commander).
• The auto standby function becomes invalid.
• When the non-operation and no sound for 5 minutes is fol-
lowed, setting will return to the state when entering demo
mode.
LED position • When insert the AC power cord into the wall outlet, it auto-
matically turns on and enters the demo mode.
front side Releasing method:

Perform the “DEMO RESET” on page 28.
Note: The demo mode does not released by unplug the AC power cord.
FACTORY INITIALIZE (Factory Settings)
Return all of the unit settings to their factory defaults. DEMO CUSTOM PRESET
It can preset the demo mode parameters.
Procedure:
1. Touch the [1] button to turn the power on. Procedure:
2. Touch the two buttons of the [1] and [–] simultaneously for 5 1. In the demo mode state, touch the two buttons of the [ ] and
seconds. [+] simultaneously for 10 seconds.
3. The all LEDs are flash 4 times. 2. The LEDs light up as shown in the following figure, and the
parameters of the demo mode are preset with the current set
The all LEDs flash 4 times.
value.
4. The reset is completed, then main unit is restart automatically. light up
USB UPDATE light up light up light up light up
Update the firmware with the USB memory can be performed.

This mode is guided by technical news, when update occurs.
light up light up
FORCED UPDATE MODE IN light up light up light up
Both firmware up/down can be performed.
This mode is guided by technical news, when update occurs.
light up light up light up
DEMO MODE
The demo mode can be performed. light up light up
Procedure:
1. Touch the [1] button to turn the power on. light up light up light up light up
2. Touch the two buttons of the [ ] and [+] simultaneously for
10 seconds. light up
3. The LEDs light up/flash as shown in the following figure.

Return to the current
light up light up light up light up light up function display.
light up
Items that can be changed settings:
light up light up light up light up • Volume (See Note 1)
• Function
The all LEDs flash 3 times. • Muting
light up light up • Subwoofer volume (See Note 2)
• Sound mode
• Vertical surround
Return to the current Note 1: Since the minimum set value of the volume is 10, it becomes 10
light up light up light up function display. even if it is set to 10 or less.
Note 2: Since the minimum set value of the subwoofer volume is 5, it
becomes 5 even if it is set to 5 or less.
3. When the “FACTORY INITIALIZE” on the left is performed,

the value set in this mode is return to the initial value and re-
lease the DEMO mode.
When the DEMO mode is released with “DEMO RESET” on
page 28, the set value will not be cleared.
27
HT-X9000F/XF9000
DEMO RESET COPY BUILT-IN DEMO CONTENTS

It can release the demo mode. It can overwrite the content to be playback with built-in demo
sound source from the USB memory.
Procedure:
1. In the demo mode state, touch the two buttons of the [ ] and Procedure:
[1] simultaneously for 5 seconds. 1. Connect the USB memory that stores the music data to be writ-
2. The all LEDs are flash 4 times to release the demo mode. ten to the main unit.
Note 1: Store the music data to be written in the “SONY_COPY_DEMO”
The all LEDs flash 4 times. folder directly under root of the USB memory.
Note 2: Copying can not be done when the music file size is larger than 90
MB.
3. Touch the three buttons of the [ ], [+] and [–] simultaneously
BUILT-IN DEMO for 10 seconds.
It can playback of built-in demo sound source or USB memory. 4. When copying is started, the LED flashes as shown in the fol-
lowing figure.
Procedure for built-in demo sound:
2. Touch the [ ] button for 3 seconds.
Note: Although it is described as “Press for 5 sec” on the label affixed
keep
to the top of the unit, it will mode in with the 3 seconds touch. flash
3. During built-in demo sound source playback, the LEDs light
up as shown in the following figure. Note 3: If an error occurs during copying, the LED flashes as shown in the
following figure.
The all LEDs flash 2 times.
The all LEDs flash quickly 4 times.
light up light up light up light up
5. When copying is completed, the LED display return to the nor-

light up light up light up light up mal state.
Releasing method for built-in demo sound:

Touch the [ ] button and return to the normal mode, or the built-
in demo sound source playback is finished, the demo mode will be
released automatically.
Procedure for USB memory:

1. Connect the USB memory with the music data to the main
unit.
3. Touch the [ ] button for 3 seconds.
4. The USB function is selected, and the music data in the USB
memory is playback automatically.
Note: Because it is a normal USB function, there is no operation for re-
lease of this mode.
28
HT-X9000F/XF9000
PANEL TEST SERVICE MODE

It can check the LED lighting state and key input. Note: For the service mode work, need a TV monitor compatible with
resolution “1920 × 1080 P” of video format.
Checking procedure:
1. Touch the [1] button to turn the power on. Setting method of the service mode:
2. Press the buttons on the remote commander in the following 1. Connect this unit with TV monitor.
order. 2. Touch the [1] button to turn the power on.
[AUTO SOUND] → [DISPLAY] → [v] → [V] 3. Press button on the remote commander in order of the follow-
3. The LEDs flash as shown in the following figure. ing.
[AUTO SOUND] → [DISPLAY] → [.] → [V]
The all LEDs keep flash slowly. (Make the interval when each button is pressed within one sec-
ond)
4. The LEDs light up/flash on this unit as shown in the following
figure, then enter the service mode to display the service mode
menu on TV monitor.
4. In the state of step 3, press the [SW 2 +] button on the remote
commander and the LEDs light up/flash as shown in the fol- The all LEDs light up. The all LEDs keep flash.
lowing figure.
The all LEDs flash quickly 4 times.
TV monitor screen
System Information
Exit
Return to the current
function display.
Each time a button on the unit is touched, LED flash in the fol-
lowing order.
Note: Buttons once touched are not counted.
flash
Releasing method:
Press the [V]/[v] buttons on the remote commander to select the
flash flash flash flash “Exit” on the service mode menu, and press the [ ] button on the
remote commander, the service mode is released and turn the pow-
All buttons are touched to the er off automatically.
flash flash all LEDs keep flash quickly.
1. Main Functions
For reference to “2. Menu Tree” on the following.
• System Information
Displays the system information of the unit.
flash flash flash Displays information such as the software version, drive infor-
mation, etc.
• Serial number Editor
5. Press the [SW 2 –] button on the remote commander and re- Edit 7 digit Serial number.
turn to the state of step 3. • Exit
Releasing the service mode.
Releasing procedure:
1. Touch the [1] button in the state of step 3 for “Checking pro- 2. Menu Tree
cedure”, the panel test mode is released and the all LEDs light
off. Service Mode Menu
6\VWHP,QIRUPDWLRQ 6\VWHP,QIRUPDWLRQ
2. Touch the [1] button again, the LEDs light off as shown in the 6HULDOQXPEHU(GLWRU 'LVSOD\VWKHV\VWHP
following figure and turn the power off. ([LW LQIRUPDWLRQRIWKHXQLW
6HULDOQXPEHU(GLWRU
(GLWWKH6HULDOQXPEHU
light off
light off light off light off light off

([LW
5HOHDVLQJWKHVHUYLFHPRGH
All LEDs light off and turn
light off light off the power off.
light off light off light off
29
HT-X9000F/XF9000
3. Service mode menu (Top Menu)

This is the top menu of service mode.
Each function is accessed from this screen.
Operation:
[V]/[v] Moves the cursor
[ ] Moves to the screen of the item selected with the cursor

System Information
Exit
4. System Information (System Information Display)

This screen displays system information.
Operation:
[V]/[v] The screen scrolls up/down
[BACK] Returns to the top menu of the service mode
System Information
mtk crypto driver init success
Device name :
:
Model name :
Destination :
Serial number :
Production ID :
BENTEN ver. :
IFCON ver. :
OSD ver. :
AIROHA ver. :
ADSP coeff ver. :
Package ver. :
AIROHA
H/W Version :
BD Address :
Sound Group :
mtk crypto driver uninit success
5. Serial number Editor

When the MAIN board is replaced, this item must be performed.
Refer to “SERIAL NUMBER WRITING WORK WHEN THE
MAIN BOARD REPLACED” on page 5 for detail.

[EDIT] [XXXXXXX]
[CLEAR]
[SAVE] Serial
number
Operation:
[V]/[v] Moves the cursor
[ ] Moves/execute the selected item
[BACK] Returns to the top menu of the service mode
6. Exit
Press the [ ] button on the remote commander, the service mode
is released and turn the power off automatically.
30
HT-X9000F/XF9000
SECTION 4
TROUBLESHOOTING
1. Protection mode is occurs after turning the power on.
When protection mode is occurs, all LEDs are flash for 5 seconds and turn the power off.
Protection mode is occurs after

turning the power on (all LEDs are
flash for 5 seconds and turn the
power off).
Yes
IC6006 on the SK1 AMP board is Yes Replace the IC6006 on the SK1 AMP
burned out. board.
No
Protection mode is not occurs, when

removing the speaker connection Yes Check and replace the speaker (SP1,
connector (CN6003, CN6004) on SP2), check and repair the connection
the SK1 AMP board and turning the cable with speaker.
power on.
No
The voltage of the following is 3.3 V. Yes The voltage of the following is 3.3 V. Yes
Replace the SK1 AMP board.
MAIN board: IC3006 pin 138 MAIN board: IC3006 pin 124
No No
OUT_A (pin 39, 40), OUT_B (pin 35),

OUT_C (pin 32) and OUT_D (pin 27, 28)
lines of IC6006 on the SK1 AMP board do
abnormality
not short-circuits or opens. Replace the SK1 AMP board.
If there is no abnormality, check the area
surrounding transistor (Q6001 to Q6003)
on the SK1 AMP board.
Mounted parts on the OUT_A (pin 39, 40),

The voltage of the following is 12 V. Yes OUT_B (pin 35), OUT_C (pin 32) and Yes Repair the short-circuit and opening of
SK1 AMP board: IC6006 pin 2 OUT_D (pin 27, 28) lines of IC6006 on the mounted parts.
SK1 AMP board short-circuits or opens.
No
No
Check the area surrounding IC6001 The PWM signal is inputted INPUT_A
and IC6005 on the SK1 AMP board. (pin 5), INPUT_B (pin 6), INPUT_C Yes Replace the IC6006 on the SK1 AMP
If IC6001 is abnormality, replace the (pin 14) and INPUT_D (pin 15) lines of board.
SK1 AMP board. IC6006 on the SK1 AMP board.
If IC6005 is abnormality, replace the
IC6005 on the SK1 AMP board. No
Check the area surrounding IC6007 on the

SK1 AMP board.
If IC6007 is abnormality, replace the
IC6007 on the SK1 AMP board.
If IC6007 is normal and area surrounding
IC6007 is abnormal, replace the SK1 AMP
board.
31
HT-X9000F/XF9000
2. The video and audio of HDMI is not outputted
The video and audio of HDMI is not

outputted.
Yes
The voltage of the following is about 3.3 V.
The voltage of the following is 5.0 V.
MAIN board: IC311 pin 3
MAIN board: CL309
MAIN board: IC312 pin 5
The voltage of the following is 3.3 V. No abnormality
MAIN board: IC309 pin 5 Replace the MAIN board.
MAIN board: CL303
Check the mounted state of the area
surrounding IC309, IC311 and IC312 on
MAIN board: CL302
the MAIN board.
Yes
Check the area surrounding NRESET line on the MAIN board.

Check the SYSCLK/XI
The voltage of the following is 3.3 V. 27 MHz is outputted from the vibrator (X5002) pin 3 on the MAIN board. abnor-
MAIN board: IC5000 pin 115 (NRESET) No 3.3 V is inputted to the vibrator (X5002) pin 4 on the MAIN board. If 3.3 V mality
The pin 118 (SYSCLK/XI) of IC5000 on the is not inputted to the vibrator (X5002) pin 4 on the MAIN board, check the
MAIN board is oscillated. transistor (Q5103) base is 3.3 V.
Check the mounted state of the area surrounding vibrator (X5002) and
Yes transistor (Q5103, Q5104) on the MAIN board.
Check the HOT PLUG DET line.

The voltage of the following is about 5.0 V. The voltage of the following is about 5.0 V. abnormality
No
MAIN board: CN5002 MAIN board: R5062, R5066 Replace the MAIN board.
pin 19 (HOT PLUG DET) The voltage of the following is about 3.3 V.
MAIN board: Q5002 base, Q5000 base
Yes
The voltage of the following is about 3.3 V.

The voltage of the following is about 5.0 V. No MAIN board: IC5001 pin 3 abnormality
MAIN board: CN5004 Replace the MAIN board.
Check the mounted state of the area
pin 18 (+5V POWER) surrounding IC5001 on the MAIN board.
Yes
Check the SCL, SDA line (mounted state

The voltage of the following is about 5.0 V. No abnormality
of connector (CN5002, CN5004) and
MAIN board: CN5002, CN5004 Replace the MAIN board.
resistor (R5001 to R5003, R5010, R5011)
pin 15 (SCL (5V)), pin 16 (SDA (5V))
on the MAIN board.
Yes
Check the mounted state of connector

The voltage of the following is about 3.3 V. No abnormality
(CN5004), diode (D600), IC101 and Replace the MAIN board.
MAIN board: CN5004 pin 13 (CEC)
resistor (R621, R653) on the MAIN board.
Yes
The voltage of the following (TMDS input

line) is about 3.0 V. No Check the mounted state of connector abnormality
MAIN board: IC5000 pin 55, 56, 58, 59, (CN5002), IC5000 and common mode Replace the MAIN board.
61, 62, 64, 65 filter (L5002, L5003) on the MAIN board.
(In the case of HDMI IN connection)
Yes
The voltage of the following (TMDS output

line) is about 3.0 V. No Check the mounted state of connector abnormality
MAIN board: IC5000 pin 22, 24, 25, 27, (CN5004), IC5000 and common mode Replace the MAIN board.
28, 30, 31, 33 filter (L5000, L5001) on the MAIN board.
(In the case of HDMI OUT connection)
32
HT-X9000F/XF9000
3. The sound is not outputted
The sound is not outputted.
Yes
Entering the “BUILT-IN DEMO” Check the signal path for being inputted to
(touch the [ ] button for 3 the IC101 on the MAIN board, and then
seconds), and then the “BUILT-IN Yes replace the complete MAIN board.
DEMO” sound is outputted. (IC101 on the MAIN board and digital
(Touch the [ ] button again to power amplifier (IC6006) on the SK1 AMP
release the “BUILT-IN DEMO”) board is OK)
No
Check the OUT_A (pin 39, 40), OUT_B
The PWM signal is inputted INPUT
(pin 35), OUT_C (pin 32) and OUT_D
_A (pin 5), INPUT_B (pin 6), INPUT Yes The voltage of the following is 28.5 V. Yes (pin 27, 28) lines of IC6006 on the SK1
_C (pin 14) and INPUT_D (pin 15) SK1 AMP board: IC6006 pin 29 to 31,
AMP board do not short-circuits or opens.
lines of IC6006 on the SK1 AMP 36 to 38 (PVDD)
If there is no abnormality, replace the
board.
No IC6006 on the SK1 AMP board.
No
Check the area surrounding IC6007 Check the fuses (F6001, F6002) on the
on the SK1 AMP board. SK1 AMP board and if it damaged, replace
If IC6007 is abnormality, replace the the fuses (F6001, F6002) on the SK1 AMP
IC6007 on the SK1 AMP board. board.
If IC6007 is normal and area
surrounding IC6007 is abnormal,
replace the SK1 AMP board.
4. Power is not turned on
Power is not turned on.
Yes
The voltage of the following is

No Fuse (F901) on the POWER board No Replace the fuse (F901) on the POWER
28.5 V.
POWER board: CN902 pin 1, 6, 7, 8 conduct the electricity. board.
Yes
Yes
POWER board is damaged.

Replace the POWER borad.

The voltage of the following is 4 V. No MAIN board.
MAIN board: CL401 If there is abnormality, replace the MAIN
board.
Yes

The voltage of the following is 3.3 V. No MAIN board.
MAIN board: CL402 If there is abnormality, replace the MAIN
board.
Yes

SK1 AMP board: CN6001 pin 3, 4
No The voltage of the following is 3.3 V. No
The voltage of the following is Replace the MAIN board.
SK1 AMP board: IC6001 pin 3
12.5 V.
SK1 AMP board: CN6001 pin 6 Yes
Yes
SK1 AMP board.
Replace the MAIN board. If there is abnormality, replace the SK1
AMP board.
33
HT-X9000F/XF9000
5. The sound is not outputted of ARC
The sound is not outputted of ARC.
Yes
Check the connection Change to the correct connection (connect the HDMI
Connecting HDMI OUT (TV (ARC)) connector of the connector of the TV to the ARC cmpatible port).
No
bar speaker and HDMI IN (ARC) connector of the TV. Change the HDMI cable.
It is connected by the supplied HDMI cable (or HDMI Sound is not outputted even if you change the connection,
cable with Ethernet). check the setting.
Yes Sound is not outputted
Check the bar speaker settings

Select the home menu screen of the bar speaker in the
following order.
³6HWXS´ĺ³$GYDQFHGVHWWLQJV´ĺ³+'0,VHWWLQJV´ Change to the correct settings.
Check the “Control for HDMI” = On If necessary, reconnect the HDMI cable after setting change.
No
Check the “TV Audio Input Mode” = Auto Sound is not outputted even if you change the settings, refer
to “The sound is not outputted”.
Check the TV settings
The HDMI control (BRAVIA sync, HDMI CEC etc.)
Sound is not outputted
setting is set to “On”.
Speaker output setting is set to “Audio system”.
Yes
Refer to “The sound is not outputted” on page 33.
34
HT-X9000F/XF9000
6. The subwoofer is not linked
The subwoofer is not linked.
Yes
If the subwoofer LED (on/standby indicator) does not light up
even if you press the [1] button on the subwoofer, refer to
No
The subwoofer LED (on/standby indicator) is light up. “2. ON/STANDBY indicator does not light up (Power is not
turned on)” on the TROUBLESHOOTING of service manual
Yes of subwoofer (SA-WX9000F/WXF9000).
Check the bar speaker settings

Select the home menu screen of the bar speaker in the Change to the secure link “Off” settings.
No The subwoofer is not linked even if you change the bar
following order.
³6HWXS´ĺ³$GYDQFHGVHWWLQJV´ĺ³6SHDNHU6HWWLQJV´ speaker settings, press and hold the [LINK] button on the
Check the “Secure Link” = Off subwoofer to cancel the secure link.
Not linked
Yes
Set the secure link settings

Bar speaker side:
following order.
³6HWXS´ĺ³$GYDQFHGVHWWLQJV´ĺ³6SHDNHU6HWWLQJV´
Set the “Secure Link” = On
Subwoofer side:
Press the [LINK] button on the subwoofer.
Not linked
Reset the bar speaker

Bar speaker side:
following order.
³6HWXS´ĺ³$GYDQFHGVHWWLQJV´ĺ³5HVHWWLQJ´ĺ
“All Settings”
(Other settings will also be reset)
Subwoofer side:
Pull out the AC power cord for turn the power off, then
insert the AC power cord for turn the power on.
Not linked
Bar speaker side:

Check whether there is any abnormality (open, short)
on the board (SK1-WS-CHUKEI board, MAIN board).
Check whether there is an abnormality (breaking of
wire) in the cable (between Bluetooth module
and CN1502 on the SK1-WS-CHUKEI board (FFC3),
between CN1501 on the SK1-WS-CHUKEI board and abnormality
Replace the defective board or cable.
CN702 on the MAIN board).
Subwoofer side:
Check whether there is an abnormality (breaking of
wire) in the cable (between Bluetooth module
and CN8101 on the SK1 SUB MAIN board (FFC1))
No abnormality
Replace the Bluetooth module

(Bar speaker side/Subwoofer side or both).
35
HT-X9000F/XF9000
MEMO
36
HT-X9000F/XF9000
SECTION 5
DIAGRAMS
5-1. BLOCK DIAGRAM - HDMI Section -
SIGNAL PATH
HDMI REPEATER
IC5000 : AUDIO (DIGITAL)
: VIDEO
CN5004
CN5002 SoC HDMI OUT
HDMI IN IC101 (1/3) TV (ARC)
DATA0+ 7 59 P2RX0P P1TX0P 14 P21 HDMI_RX_0 HDMITX_CH0_P AJ15 97 P0RX0P P0TX2M 24 7 DATA0+
DATA0– 9 58 P2RX0M P1TX0M 16 P22 HDMI_RX_0B HDMITX_CH0_M AH15 96 P0RX0M P0TX2P 22 9 DATA0–
DATA1+ 4 62 P2RX1P P1TX1P 11 L23 HDMI_RX_1 HDMITX_CH1_P AJ16 100 P0RX1P P0TX1M 27 4 DATA1+
DATA1– 6 60 P2RX1M P1TX1M 13 L24 HDMI_RX_1B HDMITX_CH1_M AH16 99 P0RX1M P0TX1P 25 6 DATA1–
DATA2+ 1 65 P2RX2P P1TX2P 8 L21 HDMI_RX_2 HDMITX_CH2_P AJ17 103 P0RX2P P0TX0M 30 1 DATA2+
DATA2– 3 64 P2RX2M P1TX2M 10 L22 HDMI_RX_2B HDMITX_CH2_M AH17 102 P0RX2M P0TX0P 28 3 DATA2–
CLOCK+ 10 56 P2RXCP P1TXCP 17 P23 HDMI_RX_C HDMITX_CLK_P AJ14 94 P0RXCP P0TXCP 31 10 CLOCK+
CLOCK– 12 55 P2RXCM P1TXCM 19 P24 HDMI_RX_CB HDMITX_CLK_M AH14 93 P0RXCM P0TXCM 33 12 CLOCK–
SDA (5V) 16 76 RX2SDA TXD1SDA 142 N25 HDMI_SDA_RX HDMISD AD17 107 RX0SDA TX0SDA 1 16 SDA (5V)
SCL (5V) 15 77 RX2SCL TXD1SCL 141 M25 HDMI_SCL_RX HDMISCK AE17 108 RX0SCL TX0SCL 144 15 SCL (5V)
HOT PLUG DET 19 TX1HPD 143 M27 HTPLG_RX HTPLG AF17 PANA_5V TX0HPD 2 19 HOT PLUG DET
+5V POWER 18 71 RX2P5V 14 RESERVE (NC)

HOT PLUG HOT PLUG B+ SWITCH
SYSCLK/XI 118 PANA_3.3V
CEC 13 HOT PLUG DETECT SWITCH VIO18_PMU DETECT SWITCH Q5103, 5104 13 CEC
DETECT SWITCH Q602 Q5000
Q5002 X5002
27MHz ARC PROCESSOR
IC5002
SERIAL FLASH DATA SELECTOR CH0ASD0 136 12 Data0 eARC_p 28

MI
IC5006 IC5009 AH23 SPI2_MI CH0ASD1 135 13 Data1 eARC_n 27
MO
AG22 SPI2_MO CH0ASD2 134 14 Data2
MI CLK
3B2 10 AH24 SPI2_CLK CH0ASD3 133 15 Data3
DO (IO1) 2 9 3A CSN HOT PLUG
PANA_PCONT
CEC
AJ23 SPI2_CSN
3B1 11
MO
127 MISO CH0ABCLK 131 10 BCK DETECT SWITCH >001B
4B2 13 CH0ALRCLK 132 11 LRCK Q5004, 5005
DI (IO0) 5 12 4A AE18 (Page 40)
4B1 14 125 MOSI/LPSA0 CH0AMCLK 129 8 MCLK
CLK
1B2 3 CH1ASD0 3 17 SPDIF HPD_IN 31
CLK 6 4 1A
1B1 2 124 SCLK/LPSA1
CSN
RESET_N
2B2 6 21 CSDA
CS 1 7 2A
MUTE
2B1 5 128 NCS 22 CSCL
S
INT
1
18 23 24
(Page 38)
ARC_SPDIF
>002B
PANA_MUTE,
PANA_MUTE EARC_MUTE
NIRQA0 37
EARC_MUTE
>003B
(Page 38)
65 66 67
eARC_INT
eARC_RESET
eARC_MUTE
HSDA0 116 120 HDMI/ESRC_SDA
HSCL0 114 121 HDMI/ESRC_SCL
NIRQ1 68 14 HDMI_INT
NRESET 115 137 HDMI_RST
48 MTK_HPD
EEPROM 134 IN1_UCON_HPD
IC5004 136 PANA_MTL_SEL
14 SDA2 SDA0 6
15 SCL2 SCL0 7
WPB 4 125 E2P_WPB
SYSTEM CONTROLLER
IC3006 (1/4)
HT-X9000F/XF9000
37 37
HT-X9000F/XF9000
5-2. BLOCK DIAGRAM - MAIN Section -

BT1
BLUETOOTH MODULE
SPDIF_OUT
SoC I2S_SDI
IC101 (2/3) BUFFER
I2S_SCLK (BCK)
IC1502
SD-RAM I2S_WS (LRCK)
IC102
DQL0 – DQL7, 16 16 CN1602

RDQ0 – RDQ15 3 T28 USB_DP_P1 URXD1 V25 BUS AIROHA_RX
DQU0 – DQU7
2 T29 USB_DM_P1 UTXD1 V24 SWITCH AIROHA_TX
15 15
A0 – A13, NC RA0 – RA14 NCEB1 H27 IC790 RESET
A/D CONVERTER,
DIGITAL AUDIO INTERFACE RECEIVER
CK J7 F14 RCLK0 CN531 MSDC0_CMD J28 BT_INT
IC7003
CK K7 E14 RCLK0_
CKE K9 A12 RCKE 1 P27 USB_VBUS_P0 BT_SDA
NC J9 63 RXIN1 2 R28 USB_DP_P0
NC L1 B20 RCS1_ 3 R29 USB_DM_P0
CN704
BA0 M2 D18 RBA0
BA1 N8 B15 RBA1 1 SDA
(Page 37)
BA2 M3 A20 RBA2 ARC_SPDIF 5 AIROHA_RX
CS L2 A18 RCS_ >002B 61 RXIN1
DATAOUT 16 N3 I2S4_DATA_IN 3 AIROHA_TX
RAS J3 A19 RRAS_ 2 BT_BOT
CAS K3 B19 RCAS_ 7 +3.3V
WE L3 B18 RWE_
DMU D3 C11 RDQM1 OPTICAL LEVEL SHIFT
LRCKOUT 15 N7 I2S4_LRCK CN202
DQSU C7 D10 RDQS1 TV IN (OPT) RECEIVER 62 RXIN2 IC752
CN1604
DQSU B7 E10 RDQS1_ URXD0 U24 BUFFER 3 RXD (IN)
DML E7 E8 RDQM0 LEVEL SHIFT UTXD0 T24 IC201, 203 4 TXD (OUT)
BCKOUT 14 N5 I2S4_BCK
DQSL F3 E12 RDQS0 IC751
URXD2 AF23 5 XDIAG
DQSL G3 F12 RDQS0_ MCKOUT 13 AA5 AUD_EXT_CK1 JTAG_RESET AF18 6 XJTAG_RESET
RESET T2 C19 DDR3RSTB AA4 AUD_EXT_CK2
J1602
ANALOG IN 45 ADINL
SD-RAM 44 ADINR WIRED_SWF_DET_MTK,

IC103 WIRED_SWF_DET_MTK WIRED_ON_MTK
AF14 AUX_IN2
MSDC0_DAT3 F29
WIRED_ON_MTK
>004B
DQL0 – DQL7, 16 16 MSDC0_DAT4 E29
RDQ16 – RDQ31 (Page 39)
DQU0 – DQU7 LEVEL SHIFT
SO 39 AJ21 SPI1_MI AMP_D0 (FL/FR), AMP_D2 (C/SW),
15 IC7206
A0 – A13, NC AMP_D0 (FL/FR) AMP_BCK, AMP_MCK, AMP_LRCK
I2S0_DATA AA1
AMP_D2 (C/SW)
>005B
LEVEL SHIFT I2S2_DATA T5
CK J7 D19 RCLK1 SI 38
IC7205
AG21 SPI1_MO (Page 39)
CK K7 E19 RCLK1_ AMP_BCK
I2S0_BCK AB2
CKE K9
SCK 37 LEVEL SHIFT
NC J9 AH22 SPI1_CLK
IC7204
NC L1 LEVEL SHIFT AMP_MCK
I2S0_MCLK AB3
BA0 K1
M2 IC750
CSB 36 LEVEL SHIFT
BA1 N8 AH21 SPI1_CSN
IC7203
BA2 M3
CS L2 XMODE 35 C29 MSDC0_DAT7 MUTE TIMING
RAS J3 CONTROLLER
X7000 31 XOUT IC785
CAS K3
24.576 MHz
WE L3 AMP_LRCK
32 XIN
DMU D3 D24 RDQM3 I2S0_LRCK AB1 11 LRCK_IN LRCK_OUT 12
DQSU C7 E23 RDQS3
DQSU B7 F23 RDQS3_ NRNB F26 10 HDMI_EXT_MUTE
DML E7 C22 RDQM2 NCEB0 G28 3 SOC_MUTE
DQSL F3 E22 RDQS2 5 HDMI_MUTE
DQSL G3 D22 RDQS2_
RESET T2 4 DIR_ERRF PANA_MUTE,
PANA_MUTE EARC_MUTE
ERRF 23 W6 DSI_TE HDMI_DEV_MUTE 6
EARC_MUTE
>003B
MUTEB 24 AD24 PCM_CLK ARC_MUTE 8
NAND FLASH
(Page 37 )
NPCMF 25 AJ27 EINT2
IC2001 2 HDMI_DIR_MUTE_SEL
INTB 40 Y6 LCM_RST
8 ARC_SEL
8 8
DAT0 – DAT7 MSDCOE_DAT0 – DAT7
RST_N K5 AC26 MSDCOE_RSTB

CMD M5 AE27 MSDCOE_CMD
11 143 12 61
CLK M6 AD26 MSDCOE_CLK
PANA_DIR_MUTE_SEL
eARC_SEL
MTK_MUTE
HDMI_MUTE
DS H5 AC27 MSDCOE_DSL 94 DEMO SIGNAL PATH
SPI0_MO L27 16 BD_SDO : AUDIO (ANALOG)

SPI0_MI K28 17 BD_SDI
: AUDIO (DIGITAL)
SPI0_CK K27 18 BD_SCL
SYSTEM CONTROLLER
SPI0_CSN L28 19 BD_CS : USB
IC3006 (2/4)
PCM_RX AF26 27 BD_REQ
PCM_SYNC AF27 28 BD_RESET(Reserved) : BLUETOOTH
URTS2 AF25 30 OPWRSB (Reserved)
PCM_TX AD25 31 UPG_STATUS (Reserved)
UCTS2 AF24 59 STREAM_STATUS (Reserved)
HT-X9000F/XF9000
38 38
HT-X9000F/XF9000
5-3. BLOCK DIAGRAM - AMP Section -

STREAM PROCESSOR
IC6007
AMP_D0 (FL/FR), AMP_D2 (C/SW),
AMP_BCK, AMP_LRCK, AMP_MCK LOW-PASS
AMP_D2 (C/SW)
>005B 25 SDIN2 PWM_M_1 38 FILTER J6001
SUBWOFFER WIRED
IC6010
(Page 38) CONNECTION
WIRED_SWF_DET_MTK,
WIRED_ON_MTK WIRED_ON_MTK
WIRED_SWF_DET_MTK
>004B (Page 38)
DIGITAL POWER AMP

IC6006
L6006
AMP_D0 (FL/FR)
24 SDIN1 PWM_P_4 49 5 INPUT_A OUT_A 39 SP1
AMP_BCK
23 SCLK (L-CH)
AMP_LRCK
22 LRCLK OUT_A 40
L6007
AMP_MCK BUFFER
11 MCLK PWM_M_4 48 6 INPUT_B OUT_B 35
IC6008
L6008
PWM_P_3 43 14 INPUT_C OUT_C 32 SP2
(R-CH)
L6009
PWM_M_3 42 15 INPUT_D OUT_D 27
OUT_D 28
OVER LOAD OVER LOAD
RESET
FAULT
OTW
CLIP
DETECT DETECT
Q6001 Q6002
4 16 17 18
VALID 37
RESET
MUTE
PDN
SDA
SCL
DC DETECT
Q6003
20 21 19 18 16
116 117 123 122 118 138 132 124

DAMP_SDA
DAMP_SCL
DAMP_XRST
DRIVER_CLIP
DC_DET
DAMP_XMUTE
DAMP_XPDN
DRIVER_XSD
SIGNAL PATH
: AUDIO (ANALOG)
: AUDIO (DIGITAL)
SYSTEM CONTROLLER
IC3006 (3/4)
HT-X9000F/XF9000
39 39
HT-X9000F/XF9000
5-4. BLOCK DIAGRAM - PANEL/POWER SUPPLY Section -

POWER MANAGEMENT
IC2302
DC/DC
VCDT A13 CONVERTER
CHRLDO R14 IC401
AVDD28 M4 VA +3.3V
UNSW3.3V REGULATOR
B14, A14, R2, R5, P7, R7, R1

AVDD22 H15 VSYS
H13, G15, F15, F14, E14,

IC402
VGP1_PMU N8 VGP1 VBAT_VSYS,
+3V
VBAT_VPROC, SoC
VGP2_PMU L8 VGP2 IR_3V REGULATOR
VBAT_VPA, IC101 (3/3)
VGP3_PMU M15 VGP3 IC3001
VBAT_LDOS1 –
VUSB_PMU N6 VUSB VBAT_LDOS3, MSDC1_DAT2 B2
VMCH_PMU R4 VMCH VBAT_SPK
B+ SWITCH
VPROC_PMU E15 VPROC AIROHA_4V
Q312, 313
D15 VPROC
C15 VPROC I2S2_DATA_IN T1
C13 VPROC_FB SPI_MISO B9 V28 PWRAP_SPI0_MI
VDD_EMI J15 VM SPI_MOSI D9 Y28 PWRAP_SPI0_MO +3.3V
BT_3.3V REGULATOR
DDRVREF SPI_CLK B10 W26 PWRAP_SPI0_CK IC1501
VCAMD_PMU L15 VCAMD SPI_CSN B7 V26 PWRAP_SPI0_CNS
VCAMD_IO_PMU M13 VCAM_IO INT C7 W28 PWRAP_INT
VCAM_AF P6 VCAM_AF SRCLKEN A2 AA27 SRCLKENA +1.8V
EXT_DDC_1V8 REGULATOR
VIO18_PMU L12 VIO18 CHG_DP A12 N28 CHD_DP_P0 IC403
VCN18_PMU K14 VCN18 CHG_DM A11 N29 CHD_DM_P0
VCN28_PMU P2 VCN28 SYSRSTB A1 AA28 WATCHDOG
VCN33_PMU N7 VCN33 RESETB M3 Y26 SYSRSTB
VTCXO_PMU N3 VTCXO +3.3V
EXT_DDC_3V3 REGULATOR
VEMC_3V3_PMU R6 VEMC_3V3 RTC_32K1V8 D6 AA29 RTC32K_CK IC404
EXT_PMIC_EN P12
+3.3V
D3.3V REGULATOR
X2300 IC406
26MHz
A4 XOUT +2.8V
SYSTEM CONTROLLER
CLK26M F2 REGULATOR
IC3006 (4/4) +3.3V
A3 XIN IC2303
X2301 DIR_3.3V REGULATOR
BENTEN 1.8V 95 32kHz AH19 26M_CLKSQ IC407
WATCHDOG 64 T901
POWER AC1
SK1 LED BOARD
TRANSFORMER (AC IN)
TH902 F901
TS_SDA W4 SDA0 VBUS DC/DC RECT LINE FILTER
USB
SWITCH CONVERTER D909 LF901
TS_SCL W5 SCL0 VBUS
IC531 IC318
TS_INT AH27 EINT7 POWER CONTROL
TS_PCONT C2 MSDC1_DAT3 MSDC1_INS D2 IC901
EXT_SDIO0 J23
LEVEL SHIFT 8 VH
USB_LED 32 LED_2 (USB_LED) SIRCS AB27 IR USB_VBUS1 P26 F902
IC204
ANALOG_LED 33 LED_3 (ANALOG_LED)
IR REPEATER DC/DC POWER ON
BT_LED 34 LED_1 (BT_LED) RECT
IC3004 DCDC_12.5V CONVERTER SWITCH 5 OUT
TV_LED 35 LED_5 (TV_LED) D913
IC6001 Q907
HDMI_LED 39 LED_4 (HDMI_LED) SWITCHING
IC3005 DC/DC
DCDC_5.5V CONVERTER 3 CS
SK1 IR REP (1) BOARD, IC6002
SK1 IR REP (2) BOARD LED DRIVE D910
Q3001
SK1-TOUCH BOARD F6001, 6002 6 VCC
IR_REP1,
AMP_PVDD
IR_REP2
+5V +12V
OVERHEAT DETECT PROTECT SWITCH
PANA_5V REGULATOR AMP_12V REGULATOR
Q901 Q903
IC311 IC6005
+5V TH901
+1.1V DC/DC
AMP_5V REGULATOR
PANA_1.1V REGULATOR CONVERTER 1 ZT
IC310 IC309 IC6003
PROTECT DETECT
PANA_3.3V Q902
PVDD
B+ SWITCH +3.3V CONTROL
SERIAL_FLASH_3.3V AMP_3.3V REGULATOR SWITCH
Q5101, 5102
+3.3V IC6004 Q908
eARC_3.3V REGULATOR D902
IC312
X1 71
X3001 SHUNT
+1.2V +5V ISOLATOR
4MHz REGULATOR 2 FB
X0 70 eARC_1.2V REGULATOR ADC_5V REGULATOR PH901
IC313 IC902
IC316
PWM4 T3
PANA_PCONT 47
MSDC0_DAT2 D27
+5V PWM3 V1
HDMI OUT +5V REGULATOR MSDC0_DAT1 E27
IC5001
LEVEL SHIFT VOLTAGE
INITX (RESET) 49 V2 PWM2 EIN6 AJ26 DETECT
Q3002, 3003
IC3003
5VPWER 60
PCONT_ON 38
AC_CUT 103
(Page 37)
PANA_PCONT
>001B
HT-X9000F/XF9000
40 40
HT-X9000F/XF9000
THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS. • Circuit Boards Location
(In addition to this, the necessary note is printed in each block.)
MAIN board
For Printed Wiring Boards. For Schematic Diagrams.
Note: Note:
• X : Parts extracted from the component side. • All capacitors are in μF unless otherwise noted. (p: pF) SK1 IR REP (1) board
• Y : Parts extracted from the conductor side. 50 WV or less are not indicated except for electrolytics SK1-TOUCH board
• f : Internal component. and tantalums.
• : Pattern from the side which enables seeing. • All resistors are in Ω and 1/4 W or less unless otherwise
(The other layers’ patterns are not indicated.) specified.
• 2 : Nonflammable resistor. SK1 LED board
Caution: • 5 : Fusible resistor.
Pattern face side: Parts on the pattern face side seen • C : Panel designation. SK1 IR REP (2) board
(Conductor Side) from the pattern face are indicated.
Note: Note: Bluetooth module
Parts face side: Parts on the parts face side seen from
The components identi- Les composants identifiés (BT1)
(Component Side) the parts face are indicated.
fied by mark 0 or dotted par une marque 0 sont
Caution: line with mark 0 are criti- critiques pour la sécurité. SK1-JACK board
Pattern face side: Parts on the pattern face side seen cal for safety. Ne les remplacer que par
(SIDE B) from the pattern face are indicated. Replace only with part une pièce portant le nu-
Parts face side: Parts on the parts face side seen from number specified. méro spécifié.
(SIDE A) the parts face are indicated.
• A : B+ Line. SK1 AMP board
• Voltages and waveforms are dc with respect to ground POWER board
• MAIN board is multi-layer printed board. However, the
under no-signal conditions.
patterns of intermediate layers have not been included in
no mark : POWER ON
diagrams. SK1-WS-CHUKEI board
* : Impossible to measure
• Indication of transistor. • Voltages are taken with VOM (Input impedance 10 M).
Voltage variations may be noted due to normal production
C tolerances.
Q These are omitted. • Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal production
B E tolerances.
• Circled numbers refer to waveforms.
• Lead layouts • Signal path.
surface F : AUDIO (ANALOG)
J : AUDIO (DIGITAL)
L : USB
E : Bluetooth
Note 1: When the complete MAIN board is replaced, be sure

to refer to “SERIAL NUMBER WRITING WORK
WHEN THE MAIN BOARD REPLACED” on page
Lead layout of conventional IC CSP (Chip Size Package) 5.
Note 2: Among mounted electrical parts on each board, only

Note 1: When the complete MAIN board is replaced, be sure parts that are described in the electrical parts list can
to refer to “SERIAL NUMBER WRITING WORK be replaced for repairing.
WHEN THE MAIN BOARD REPLACED” on page The parts that are not described in the electrical parts
5. list cannot be replaced with single for repairing.
Note 2: Among mounted electrical parts on each board, only

parts that are described in the electrical parts list can
be replaced for repairing.
The parts that are not described in the electrical parts
list cannot be replaced with single for repairing.
HT-X9000F/XF9000
41 41
HT-X9000F/XF9000
5-5. PRINTED WIRING BOARD - MAIN Board - • See page 41 for Circuit Boards Location. • : Uses unleaded solder.
1 2 3 4 5 6 7 8 9 10 11 12 13 14
MAIN BOARD (SIDE A) (SHIELD) (BRACKET) (SHIELD)

X3001
A CL5001 R5011
C5056
1 4
R5017
K D301 A
CL309
1 4
C307 JL3026
R5002 2 3 C308 2 3
R304 JL3029 JL3027 JL3018 JL3014 JL3010
IC311
C5055
R5001 JL3031 JL3020 JL3016 JL3015
ET307
R5014
C5053
R3038
R5010 JL3024 JL3012
L5001 ET5002 JL3019
JL3032
19
IC5001
R3035
JL3025 R3033 JL3013
JL3030 R3034
R5113
R5083
R5084
CL3047
CL3050
JL5008
C3020
JL3023 R3073 JL3034 JL3033
JL5010 JL5006 JL3017 RB3004
R3004
R3005
C3004
L5000 JL3021 CL3046 C3019 JL3035
CL5034
R3006
R5179
C3035 C3016 R3016 R3017
R5024
CN5004 JL5011 JL5012 JL3038
JL3037 JL3039
36 1 R5141 R3018
R3015
C128 JL3036
FB5003
1
C5030
JL5009 JL5007
R649
R600
R651
C5041 CL5033 JL110 144 109 Q3001
R3003
R5129 E
37 144R5082 108 C3023CL3033
R3064
C3032
C3005
C132
C120
1 4 1 4 3
IC3005
C130
CL3002
JL143 JL114
R5120
R5122
R5012 JL5005 JL2189 R615 C3009 IC204 5 1
C5043
HDMI R5013 C108 R616 3 1 C3007
R3052 R3065
JL164
C115
B
JL113
R5123
R5081 ET5001 JL111 JL118 Q602 4 3 2 1
OUT C319 4 1
C318
C107
3 R3043
R225
JL109
CL304 5 8
C3003
6 5 1 JL139 C126 JL144 4 R3055 4 L3001
R5028 CL5032
TV (ARC) JL117 3 4
FB5002 JL115
IC3003
CL3006
C3001
4 R310 C121 JL140C119 C140 JL141
R3077
1
C5034
CL3038
C5085
IC5006
JL112
JL116
C3022
2 3 C221 JL2164 C138 C114 1 2 C3008
IC313 R109 R104
IC3004 IC3001
R3002
C109 CL3037
R105
C2384 C141 R110 JL119 R108 C3033
R3059
CL3007
CL3008
JL2163 CL3039
R5036 R5131
C5101 C123 JL122
19 JL142 R3063
5 8 JL132 C125 C139 C116 JL120 JL128 C112
RB3002
CL3040
CL2305
IC5000 C137 R3062
C113
ET5003 JL304
CL2320
JL108 JL2186 C117 C3021
IC3006
CL2304
JL137 CL3041 C3036
CL3055 CL3056 CL3059

C2389
JL131 JL105 JL127JL135 JL2104
C2427
C2426
L5003 R5124 C122
R5033
R5027 C2399 C143 CL3042 R423
C111 C110
CL3058
C127 JL107 JL133 C136 JL129 JL136 CL3003
C142 JL138 JL2184 JL121 CL3057 L401
C124 R3013
C424 CL2322 JL130 C131
C423
CL2315 CL3034
C129
CN5002 L5002 R5037 C133 JL106 JL134 R704 R3010 JL303
1 JL125 R106 C104 R3051
3 2 FB403 1 4 JL2301 JL2185 CL3001
2 3 R2400 JL2182 JL104 R107 R103 R3054 C404
R2337
CL2308
CL2309
CL5042 X5002 R426 JL123 R3011 C401 JL302
C134 JL2126
C5069 4 1
CL406
IC407 C105 C102 R3012
R702
R705
C2369
JL124
R2393 R3050
C2357
C2360
JL2187 C2348 C106 C403
C2342
HDMI R5207 R229 C2366 C103
C2372
72 109 C2430 JL301
C2363
ET5005 CL2321
C
C2327 C2343
C5032
36 73
C2317
IN R5068 C2361 C135 C3029 L402
Q5104 C2316 RB703 C408
C3030
4 3
IC2303 R230 R233 37 72
C2324
73 108 E
R2317 C2370 CL2323 CL3051 C3012 C3013 R3025 CL3043 R3040 C407
R3041
Q5103 1 2 R701 R3044
C2351
C2339
C2335
R5200 C2332 C2353 C3006
R3076
C2310 R216
CL3052
E
R2325
R3020
C2428 C2322 C2338 C2337 C3010
R3078
ET308
C3011
C2347
C2318 R217
IC7205
IC7203
IC7204
C2359 R2318 C2315 R3024 R3032
X3001
R5205
R5206
C2328 CL3049
C2340
C2368 C2358 CL3004
R418 R207 3 1 R3085 CL3048
C2365 C2371 R714
IC750
CL3044
CL3045
ET5004 R417 R416 C2364 C2354 C2344 CL3053 E Q3002 R3039 C3018 C3017
C7209
C7208
C7205
C7204
C7207
C751
C2346 C2350 CL3054
IC7206 6 4 6 4 CL240 4 5
R796
C2362 C2314 C2341 R715 R228 JL308
C2356
C416 CL238 R3081
C2309
R750
R752
R3082
R7219 4 3 1 6 1 6 1 6 C7206 CL242 C2326 C2319
IC403 JL305
CL719
CL243 R780 R3072
IC404
C415
CL102 ET312
C2334
C2323
R278 C2312
C2320
1 3 4 3 4 3 4 C2333 C2345 L701
CL718
C7210 5 C2325 C2336CL200 CL725
C2367 R204
Q3003
C2352 R617
1 3 1 3 C2329 C2321 R782 CL726E
ET311 C8002
C793
JL7001 JL7006 R781
CL405 C417 R765
IC2001 C418 C2349 C2313 FB8000 JL202 CL727 R779
JL7002 R2013 1211 CL703
CL201
CL791
CL792
C2355
C2311
R257 C600
C202
FL2001 CL257 C791 1 10 C792
CL236
JL306 (BRACKET)
R5066 R618
CL210 R215 CL209
CL298
CL297
CL296
(SHIELD) JL7003 JL7004 CL5038 R783 4 7 R788
CL728
FL2002 CL258 CL255 R784 5 6 JL307
JL7005 JL7007 C2004 R7214 E
R620
R201
D
CL730
R211 CL256 R732 14 8
CL735
CL264
JL2007 R619
CL734
CL736
JL2010 R275 Q5000
CL205
R626
R627
P14 P13 P12 P11 P10 P9 P8 P7 P6 P5 P4 P3 P2 P1 IC101 C2009 R218 R210 CL729 C794
R733
JL2008 R240
IC790
C2001
C2008
N14 N13 N12 N11 N10 N9 N8 N7 N6 N5 N4 N3 N2 N1 AJ29 AJ28 AJ27 AJ26 AJ24 AJ23 AJ21 AJ20 AJ18 AJ17 AJ16 AJ15 AJ14 AJ12 AJ11 AJ9 AJ8 AJ7 AJ6 AJ5 AJ4 AJ3 AJ2 AJ1 R212 RB705
C2010 R213
IC785
CL203
CL709 RB3005
R723
R730
CL8039
CL8037
CL8041
CL208
CL207
CL202
M14 M13 M12 M11 M10 M9 M8 M7 M6 M5 M4 M3 M2 M1 AH29AH28AH27AH26AH25AH24AH23AH22AH21AH20AH19AH18AH17AH16AH15AH14AH13AH12AH11AH10 AH9 AH8 AH7 AH6 AH5 AH4 AH3 AH1 C2002 R2001 C206
C2003 JL2009
R239
R280
L14 L13 L12 L3 L2 L1 AG29AG28 AG26AG25AG24 AG22AG21 AG18 AG13AG12AG11AG10 AG9 AG6 AG5 AG3 AG2 AG1 1 7 JL201 JL3004
JL2011
AF29AF28 AF27AF26AF25AF24AF23 AF21 AF18AF17 AF15 AF14 AF9 AF8 AF7 AF5 AF2 AF1 JL703 CL8036 RB706 JL3002 JL3006
K14 K13 K12 K10 K9 K8 K7 K6 K5 K3 K2 K1 JL701 CL8038
AE29AE28AE27 AE23 AE21AE20AE19AE18AE17 AE15AE14 AE12AE11 AE9 AE8 AE7 AE6 AE2 AE1 JL710 R769 CL8040 JL534
J14 J13 J12 J10 J5 J3 J2 J1 JL707 CL704
JL720 JL708 R797 CL705 CL790
AD28 AD26AD25AD24 AD22AD21 AD19AD18AD17 AD15AD14AD13AD12AD11AD10 AD8 AD6 AD5 AD4 AD2 AD1 JL713
JL717
JL719
JL3003
JL3005
JL3007
H14 H13 H12 H10 H5 H3 H2 H1 JL3001
CL702
JL702 CL707 7 1
CL701
AC29AC28AC27AC26 AC24 AC21 AC19AC18 AC15 AC13 AC9 AC8 AC6 AC3 AC2 JL712 JL715 JL531
CL708
G14 G13 G12 G10 G5 G3 G2 G1 JL706 R775 CL706 CN704
F14 F13 F12 F10 F5 F3 F2 F1 AB27 AB24 AB22 AB20AB19AB18 AB15 AB13AB12AB11AB10 AB9 AB6 AB5 AB4 AB3 AB2 AB1 JL704 7 1
R731 JL533
E14 E13 E12 E10 E9 E8 E7 E6 E5 E3 E2 E1 AA29AA28AA27 AA22 AA20 AA18AA17 AA15AA14AA13AA12AA11 AA5 AA4 AA2 AA1 CN3001
JL532 11
E Y28 Y27 Y26 Y25 Y24 Y22 Y21 Y20 Y19 Y18 Y17 Y16 Y15 Y14 Y13 Y12 Y11 Y10 Y6 Y3 Y2
JL705
JL709
JL711
JL714
JL716
JL718
D14 D13 D12 D4 D3 D2 D1
W29 W28 W27 W26 W25 W24 W22 W20 W19 W18 W17 W15 W14 W13 W12 W11 W10 W9 W8 W7 W6 W5 W4 W3 W2 W1 (NC) 1-982-490- (11)
C14 C13 C12 C11 C10 C9 C8 C7 C6 C5 C4 C3 C2 C1
V28 V27 V26 V25 V24 V22 V21 V20 V19 V18 V17 V16 V15 V14 V13 V12 V11 V10 V9 V8 V7 V6 V5 V4 V2 V1
B14 B13 B12 B11 B10 B9 B8 B7 B6 B5 B4 B3 B2 B1 (NC)
U29 U28 U27 U24 U22 U21 U20 U19 U18 U17 U16 U15 U14 U13 U12 U11 U10 U3 U2 (BRACKET) (BRACKET)
A14 A13 A12 A11 A10 A9 A8 A7 A6 A5 A4 A3 A2 A1
T29 T28 T27 T25 T24 T23 T18 T17 T16 T15 T14 T13 T12 T11 T10 T9 T7 T6 T5 T4 T3 T2 T1
R29 R28 R27 R26 R24 R20 R19 R18 R17 R16 R15 R14 R13 R12 R11 R10 R9 R8 R3 R2
IC2302 N29 N28

P27 P26 P25 P24 P23 P22 P21 P20 P19 P18 P17 P16 P15 P14 P13 P12 P11 P10
N25 N20 N19 N18 N17 N16 N15 N14 N13 N12 N11 N10 N9 N8 N7 N6 N5 N4 N3 N2 N1
P7 P6 P5 P3 P2 P1
SK1-JACK SK1 AMP SK1-WS-CHUKEI
M29 M28 M27 M26 M25 M20 M19 M18 M17 M16 M15 M14 M13 M12 M11 M10 M3 M2 (NC)
>03P BOARD >05P BOARD >04P BOARD
A1 A2 A3 A4 A5 A6
B1 B2 B3
A8 A10 A11 A12 A13 A14 A15
B6 B7 B8 B9 B10 B11 B13 B14 B15
L29 L28 L27 L25 L24 L23 L22 L21 L20 L19 L18 L17 L16 L15 L14 L13 L12 L11 L10 L9 L8 L7 L4 L3 L2 L1 (Page 43) MAIN BOARD (SIDE B) (CHASSIS) CN1601 (SHIELD) (CHASSIS) FFC4
CN6005 CN1501
(NC)
K28 K27 K26 K25 K20 K19 K18 K17 K16 K15 K14 K13 K12 K11 K10 K2 K1 SK1-JACK
C1 C2 C5 C7 C8 C9 C10 C11 C13 C15
BOARD
F D2 D3 D4 D5 D6 D7 D8 D9 D11 D13 D15
J29 J28 J27 J26 J25 J24 J23
H29 H27
J21
H19
J18 J16 J15 J14
H17 H16 H14
J12
H12
J10 J9 J8 J7 J5 J4 J3 J2 J1
H2 H1
CN1601 CN532
28 2
CN702
CN202
E1 E2 E6 E9 E11 E13 E14 E15
>02P 1 5
IC531 1 12 6 1
C531
G28 G27 G25 G23 G22 G21 G19 G18 G15 G14 G12 G11 G8 G3 G2 G1 CN701 CN531
F2 F3 F5 F6 F9 F11 F12 F14 F15 C534 1 5 27 1 4 1
F29 F28 F27 F26 F25 F23 F19 F18 F15 F14 F12 F10 F8 F5 F4 F2 F1 C533 C788
G1 G2 G3 G6 G7 G8 G9 G10 G11 G13 G15 R535 R725 R771 CL225 CL223 CL222
L702 R770
E29 E28 E27 E26 E25 E23 E22 E19 E18 E15 E14 E12 E10 E8 E7 E2 E1 3 4 R724 R773 C797 C798 FB701
H1 H2 H3 H4 H5 H6 H8 H10 H11 H13 H15 R531 (CHASSIS)
RB701
R726
R729
D28 D27 D26 D24 D23 D22 D19 D18 D15 D14 D11 D10 D6 D4 D3 D2 D1 R787 R778
C532
R532
J1 J2 J5 J7 J8 J9 J11 J12 J15 JL2006 D600 R776
R653 CL501
K2 K3 K4 K6 K7 K8 K10 K11 K12 K14 K15
C29 C28 C27 C26 C25 C24 C22 C21 C20 C19 C18 C16 C15 C14 C13 C11 C10 C9 C8 C5 C2 C1
R621 A K R777 L703 R772 CL308 CL226 CL221
CL2019 R537 ET309
B29 B28 B27 B26 B25 B24 B23 B22 B21 B20 B19 B18 B17 B16 B15 B14 B13 B12 B11 B10 B9 B8 B7 B6 B5 B4 B3 B2 B1 CN7001 CL2001 R538 CL224
R244
R245
R246
L1 L2 L6 L8 L9 L11 L12 L15 R329
A29 A28 A27 A26 A24 A23 A21 A20 A19 A18 A17 A16 A14 A12 A11 A10 A9 A7 A6 A5 A4 A3 A2 A1 1 7 CL2018 C349
M1 M3 M4 M6 M8 M10 M12 M13 M15 CL2002 CL2003 R243
1 6 C203
R299 R209 R208
N1 N2 N3 N6 N7 N8 N10 N11 N12 N13 N15 ET314 IC2001 JL2005 R2014 R285 C2429 CL503
Q313
3 4
C201
1 5
R220
1 5
C2012 C2011
P1 P2 P3 P6 P7 P8 P10 P11 P12 P13 P14 P15 R286 R297
X2301 C350 R327 3 4 3 4 IC203
G R1 R2 R3 R4 R5 R6 R7 R8 R10 R11 R13 R14 R15
(SHIELD)
CL2008
CL2011
CL2017 R7216 R298
R2342
E R328
IC201 R222
6
R7018
CL2016 R287 R291 Q312 C314
CL2007 R2395
CL2015 CL723 R306 R308
R7003
R7017 R7108
C328
C327
R7019
FB7001
CL2010 CL204 C305

C7006
C7007
CL2014 C313 R303 R309 CN303

CL2012 CL2006
IC318
R7021
R7016
(Page 44)
R7020
C5057 IC316 FB304 CL305 R7011 CL2013

CL2009 CL8012 6 4
>06P
IC5004 R7012
X7000
C7017 JL2002
CL2005
C316
C304
C303
R5044 C312 C7010 CL2004 R206 R3080
CL8034
R5043 JL2004 SK1 AMP
CL8004
CL8006
9 8 C7012 JL2001 JL2003 1 3
R708
R710
R7212
CL8035
CL8005
CL8015
CL8016
CL8010
3 2
R709
C310
C7008 CL299 CL307 BOARD
R7023
C5059 C315 L301

CL295
C301
R5023 4 1 C7013 C7009 C7015 C7014 R711 R712 C306 CN6001
C7016
R5042 R311 R7026 1

48 33 R202 R203 CL614
C311 C7026 R7025
IC101
C2331
C2330
R5041 R404 R403
CL293 R7211
R262
R263
16 1 49 32 R713 L302
CL2316
C5060 CL610
CL711 CL722
CL710 C409 C405
R2351 C2394
RB5014 RB5005 CL294
R5051 C7025 CL712
CL721
R2339
CL5039 ET306 4 3
CL206
R261
R264
R7030 CL241
R2336
CL609
R2350
R5080
CL615
CL5040 C7020
CL713
CL606
IC7003
CL616
CL720
C5067 R7001
R2340
R5079
H R5202 R5201 R7002
X2300
R249 CL260 IC401
C2382
R5078 C5036 C5037 C5025 R2341 CL306
CL2319 R256 CL732
C2383
C7022 CL733
R5018
R5072 R5077 R2349 CL724

C5006 C5022 C5027 CL2307 C2379 C2380 R284 R102 CL717 5 8 4
C5042 R5032 C7021 CN301
C402
CL731
64 17 C2390 CL715 CL401
CL5035 CL2318 CL2312 C2398
(Page 46)
R700
C5005 R5031
R271
CL714
IC402R407 R401
>07P
CL2310
CL5037 R5029 1 16 C2385 L2303
C2388 A1 A2 A3 A7 A8 A9 A1 A2 A3 A7 A8 A9 CL716 CL402 FB401
C2395
4 3
R5019
C5044 R7045 C2397 B1 B2 B3 B7 B8 B9 B1 B2 B3 B7 B8 B9 R402 POWER

R5020
C7024
C7027
R7063
R7058
R7060
C5084
R406
C2381
R7054
R405
C5019 C1C2C3 C7C8C9 C1C2C3 C7C8C9 BOARD
C412
R5030 1 4
CL8008
CL8009
IC2302 D1D2D3 D7D8D9 D1D2D3 D7D8D9
JL8036
5 1
R5104
Q5002 R5102
R5100
R5099
R5097 C5088
R5132
R5094
C5028 C2396 FB402 2 3

E1 E2 E3 E7 E8 E9 E1 E2 E3 E7 E8 E9 CN902
C5118
L2302
R2333
R409
R5054
C5065
C2392
C422
CL5036 F1 F2 F3 F7 F8 F9 F1 F2 F3 F7 F8 F9 CL403
R5003
C5033 RB5003 R425 C411

R753
C753
C2391 G1G2G3 G7G8G9 G1G2G3 G7G8G9 C347
IC103
IC102
R5190 R2331 R3074
R394
CL5014
1 16 C5119 CL2317
C2393 H1H2H3 H7H8H9 C144 H1H2H3 H7H8H9
IC406 C348
SK1 IR REP (1)
CL5030
J1 J2 J3 J7 J8 J9 J1 J2 J3 J7 J8 J9 ET301 C222 CN3002

R5061
E
CL311
C5048 CL5015 R5188 1 5 IC752 C2378 R2329 CL2300 K1 K2 K3
CL2301
CL2302
L1 L2 L3
K7 K8 K9 JL165
L7 L8 L9
K1 K2 K3
L1 L2 L3
K7 K8 K9
L7 L8 L9 C223 4 BOARD
R7208
R7210
R5062 CL5020 CL5016 R5186 E 3 4
C2376
CL5029 Q5101 CL3036 M1M2M3 M7M8M9 R111 M1 M2M3 M7M8M9

C2374
C2400
CL310
C2375
C2377
C2373
C5029 R5192 N1N2N3 N7N8N9 N1N2N3 N7N8N9
R5101
IC5009 C752 ET303 SK1 IR REP (2)
R3019
R3021
R3026
R3027
R3029
R3031
R3036
8 9 CL3035 1
I
P1 P2 P3 P7 P8 P9 P1 P2 P3 P7 P8 P9
C2387
C2386
C5109 C5086 FB5001 C5083 Q5102 1 5
C5074 R5187 R5191 E R1R2R3 R7R8R9 JL2106 R1R2R3 R7R8R9 BOARD
C5092 24 17 C5091 FB5004 C5040 C5039 3 4 T1T2T3 T7T8T9 T1T2T3 T7T8T9
R5189
R5128
R5181
25 16 R5127 R793
IC5002 RB5002
C5000
R5125 IC751 JL2188
JL2105 C118 R794 FB3002
C5013
C5003
C5010
C5004
C5089 R5093
FB5006
FB5005
FB5007
R798
R799
32 9 7 1
CL5019
C5093 R376
CL5018
C387
CL5017
R5098 1 8 CN5005
R5092 R385 R384 6 2
C5090
C5087 R383
C5076 C5063 R5091 C386
R391
IC309 CL3031
C3034
R3058
R5103
R5105
C5120 R389 R388 6 4

CL5011
CL5012
(NC)
R5007
E
R5142
IC310 C389 FB3003
RB3003 CL3032 CL3022 CL3021
C384
C383
R5049 E R5180 C3015 C3014

C395 15 11 C391 1 3
CL303
4 1 C388
C385
R5048 Q5004 ET305

16 10
C399
C346
Q5005
IC312 16 2
C394
CL302 CL301 L312

5 8 20 6 CN3004 CL3030 CL3024 (SHIELD) (SHIELD)
R390 15 1
R325
R378
C390
R379 1 5 L313 11
J C398
R381
C393
1-982-490- (11)
(CHASSIS) (SHIELD) SK1 LED SK1-TOUCH (CHASSIS) (CHASSIS)

BOARD BOARD
FFC1 FFC2
Note: When the SK1 TOUCH, SK1 LED, SK1 IR REP (1)
or SK1 IR REP (2) boards are defective, replace the
complete mounted board or the whole parts including
the applicable board.
The mounted parts cannot be replaced with single for
repairing.
HT-X9000F/XF9000
42 42
HT-X9000F/XF9000
5-6. PRINTED WIRING BOARDS - SK1-JACK/SK1-WS-CHUKEI Boards - • See page 41 for Circuit Boards Location. • : Uses unleaded solder.
1 2 3 4 5 6 7 8 9
SK1-JACK BOARD (SIDE A) SK1-JACK BOARD (SIDE B) SK1-WS-CHUKEI BOARD (SIDE A) SK1-WS-CHUKEI BOARD (SIDE B)
JL1604
IC150210
A 4
R1515
11
CN1602 (CHASSIS) R1548 R1516

C1608 R1521 L1501 CN1502 R1524 20 1 R1513
1 R1501
C1607
R1502
C1509
JL1605 FB1602
1 >02P (Page 42) (Page 42) R1503
R1504 17 18
FFC3 C1508
MAIN CN1501 BT1

CL1605 BOARD >04P BLUETOOTH
CN1601 MAIN R1505 MODULE R1509
CN7001
CL1603 BOARD R1519 2 R1510 R1508
FB1601 1
1 5 6 12 CN702 12 R1550 R1506 R1507
R1520
>03P (Page 42) R1549 CL1522 C1501
JL1608 MAIN 1 4 R1511
B
JL1603
JL1601
(CHASSIS)
C1605
BOARD
CN532
C1506
CL1551 11
C1510 IC1501 C15033
2
11
R1601
FB1604
R1603 J1602 1-982-495- (11) 1-982-495- (11)
R1605 ANALOG IN
C1601
R1606
C1602
R1604
R1602
C1603
(CHASSIS)
C1604 JL1602
C1610
2 R1610
CN1604
3 TV IN (OPT)
C1609
1
FB1603
C
11 11
1-982-493- (11) 1-982-493- (11)
(CHASSIS)
5-7. SCHEMATIC DIAGRAM - SK1-JACK/SK1-WS-CHUKEI Boards - • See page 48 for Waveforms. • See page 48 for IC Block Diagrams.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
SK1 IR REP (1) SK1 IR REP (2)

BOARD BOARD SK1-JACK BOARD SK1-WS-CHUKEI BOARD
A JL1604
(CHASSIS) IC1501
CN1601 +3.3V REGULATOR
12P IC1501
CL1603 4 MM3411A33URE
DGND 1
• See3 page CN1602
46 for Waveforms. • See page 46 for IC Block Diagrams. 4 4 1 3.9
CN1502
18P
DP 2 VDD CE
2 3.3 3 2 CL1522
MAIN DM 3 VOUT GND 1 GND
BOARD CL1605 1
(1/5) VBUS 4 CL1551 2 AIROHA_RX
GND(SHIELD) 5 FB1601 C1607 C1608
220p 220 3 BT_3.3V
JL1608
B
FFC1 6.3V C1510 C1501 C1503 R1509 R1507 R1510 R1508 R1513 C1506 R1511 L1501
DEMO 6 0.01 1 1 10k 1k 3.3k 3.3k 3.3k 330 10k 10uH 4 BT_INT
(CHASSIS)
6.3V
SK1 LED L-CH 7 5 I2S_SCLK(BCK)
FB1602
BOARD
AGND 8 6 GND
CN1501 R1549 R1550
R-CH 9 12P 47k 4.7k
7 I2S_MCLK
FFC2 FB1604 FFC3
DGND 10 C1603 R1603 R1601 PMIC_4V 12 8 GND
10 18k 2.2k JL1601 R1520
SK1-TOUCH OPT_IN 11 GND 11 9 I2S_SDO BT1
22 BLUETOOTH
BOARD MODULE
D3.3V 12 C1601 R1605 J1602 WS_INT/BT_INT 10 10 I2S_WS(LRCK)
R1506 22
47p 15k
WS_SCLK/BT_RST 9 11 MUTE
ANALOG IN R1519 22
C C1602 R1606
AIROHA_RX 8
R1505 22
12 BT_BOOT
MAIN AIROHA_TX 7 13 SPDIF_OUT
47p 15k R1604 R1602 BOARD R1504 220
18k 2.2k (2/5) WS_LRCK 6 14 GND
R1503 220
C1604 WS_BCK 5 15 I2S_SDI
JL1602 R1502 22
10
UPDATE 4 16 AIROHA_TX
R1521 220
DATA_X(SWF) 3 17 BT_SDA
C1605
1000p
C1610
0.1 GND_SHIELD 2
R1501 0
R1548
22
IC1502 18 GND
SPDIF_OUT 1 BUFFER
D JL1603
FB1603
1
IC1502
74LCX541FT
(CHASSIS) VCC
2 CN1604 C1508 C1509
1 20 3.3 0.1 10
VOUT VCC
R1610 3 TV IN (OPT) 0 2 19
100 C1609 GND
0.1
3 18 0
1.6 4 17 R1524
JL1605 220
5 16 1.6
(CHASSIS)
0 6 15 R1516
220
1 7
8
14
13
0
R1515
E 9 12
220
10 11
GND
Note 1: When the SK1 TOUCH, SK1 LED, SK1 IR REP (1) Note 2: When the Bluetooth module is replaced, be sure
or SK1 IR REP (2) boards are defective, replace the to refer to “WIRELESS CONNECTION (LINK)
complete mounted board or the whole parts including WORK OF BAR SPEAKER AND SUBWOOFER”
the applicable board. on page 6.
The mounted parts cannot be replaced with single for
repairing.
HT-X9000F/XF9000
43 43
HT-X9000F/XF9000
5-8. PRINTED WIRING BOARD - SK1 AMP Board - • See page 41 for Circuit Boards Location. • : Uses unleaded solder.
1 2 3 4 5 6 7 8 9
SK1 AMP BOARD (SIDE A)
J6001
SUBWOOFER
WIRED CONNECTION (Page 42)
MAIN BOARD
A FFC4
>05P CN701
LN6005 L6011 LN6003

R6036
R6031 R6033
R6030
JL6033 C6077
1 CN6005 27 C6080 L6010
(CHASSIS) CL6019 CL6012
2 28 28 R6029 1
C6089 JC6023
C6095
C6098
CL6023
JC6013
R6052
R6044
CL6026 (CHASSIS)
IC6007
R6045
R6048
R6050
B R6064 R6063 C6032
C6029 4 3 C6022
IC6010 R6075
5 1
C6021 CL6001
8 5
L6012
C6102
IC6003 29
R6041 R6037 C6085 C6076
56 C6078
LN6001
C6104 R6071 R6072 C6070
C6105
C6013
1 4 CL6020 C6073 C6006
R6070 C6014
C6096 R6038
C6100 R6069 C6101 (CHASSIS)
C6099
R6021
R6020
R6014
JL6008
R6065 A K
L6002
C6112
C6026
R6066
R6068
C6103
R6018
D6003
FB6002
C6045 CL6025
R6025 C6049 R6013 C6035
1
C 22 1 C6036
3 1
C6030 CL6008
4 5
IC6005 C6034 C6005 CN6001
CL6005
ET6002 ET6001 C6037
C6033
CL6006
>06P (Page 42)
IC6006 JL6004 FB6001
CL6004 MAIN
BOARD
CN303
(CHASSIS) 23 44 C6002 C6001
6
C6111 C6110 C6003 CL6002
L6001
A
C6059 C6047 K D6001
CL6010
D 1
C6024 C6025
L6009 L6008 L6007 L6006 CN6002
C6064 C6048
F6002 F6001 R6006
C6011 >01P (Page 42)
POWER
BOARD
C6043 CN902
C6066 C6054
C6057 7
C6042 JL6010 CL6009
C6065 C6056 C6053 C6019 C6016
E LN6002
CL6017 CL6015
LN6006 LN6004
CL6016
5 1 4 1
CN6004 CN6003 CL6013
CL6007 JL6009
CL6014 CL6022 CL6003
(CHASSIS) 11
1-982-506- (11)
(CHASSIS) (CHASSIS) (CHASSIS)
F SK1 AMP BOARD (SIDE B) SP1 SP2

(L-CH) (R-CH)
C6107 C6106
C6109 C6108
C6051 C6046
C6063 C6061
JL6012 JL6011
C6092
C6093
R6056
E JL6014 JL6013
Q6003
A A
K K JC6011
D6006 D6005 Q6001 Q6002
R6061
R6022 1 6 4 3
R6016 JL6006
R6024
G 3 4
C6038
6 1 R6017
C6041
R6011
R6012
FB6003 JL6007
L6003
R6023 R6019 C6012
C6058
C6055
1 8
H C6007 R6004
C6017
C6008 R6005 JL6002
CL6021 R6026 C6068 C6040 R6002
4 5
C6067
R6015
CL6011 IC6001 R6001 JL6001
C6062 C6052 R6003
C6044
FB6004
C6069 C6039 JL6005
L6005
L6004
CL6018 C6060 C6050
C6015
I 3 1
JC6007
JC6006
C6018
IC6002
4 6 JL6003
IC6008
R6009
C6097 R6010
R6008
R6007
R6049
JL6017 JL6022
C6023
R6073 1 5 C6090
R6053
R6074 3 4 C6031 1
C6091 4 K A
JL6024 R6046 2 3 D6002 11
CL6024 JL6018
R6047
C6028
R6027 C6020 IC6004 1-982-506- (11)
JL6016 JL6020 JL6027

C6072 C6071
JL6025 JL6031
JL6032
JL6030 C6075 R6028
J R6054
R6032
R6034
R6035
R6040
R6043
JL6026 JL6028 JL6029 C6074

JL6015
Note: When the IC6006 on the SK1 AMP board or the SK1 JL6019 JL6023
C6087
AMP board is replaced, spread the compound to the R6039
C6084
R6042
JL6021
touching portion between the IC6006 and the heat sink.
HT-X9000F/XF9000
44 44
HT-X9000F/XF9000
5-9. SCHEMATIC DIAGRAM - SK1 AMP Board - • See page 48 for Waveforms. • See page 48 for IC Block Diagrams.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
SK1 AMP BOARD

A LN6002
CL6003
(CHASSIS)
LN6004 R6061
CL6007 R6024
15k 100k
C6042 C6053 C6056 C6065
(CHASSIS) 1000p 1000p 1000p 1000p R6011 C6038
F6001 5A 32V
F6002 5A 32V
LN6006 R6022 100k 2.2
CL6022 100k
B (CHASSIS)
C6043
1
C6054
1
C6057
1
C6066
1
14.1 14.1
R6016
100k 1 4
CN6004 C6109 0.01 L6007 L6008 E E
5P C6055 R6019 R6023 C6058 14.1 2 B B 5 14.1
470p 10uH 10uH 470p
JL6014 C6063 1000p 10 10 R6012 C6041 C C
FL– 5 R6017 100k 2.2
100k 6 3
CL6017
FL– 4 L6006 L6009 0 0 Q6001
SP1 10uH 10uH HN1A01FU
NC 3 CL6014 OVER LOAD DETECT
(L-CH) JL6013
FL+ 2 R6015 C6048 C6064 R6026 14.1 14.1
CL6016 C6061 1000p C6044 C6067
10 470 470 10 1 4
470p 470p
12.7
11.9
C FL+ 1
C6108 0.01
35V 35V
14.1 2 B
E E
B 5 14.1
C C
4
C6047 C6059 D6006
CN6003 1 C6052 C6062 1 DZ2J300M0L 6 3
C6107 0.01
VOUT
VIN
4P 0.047 0.047 Q6002
0 0
JL6012 C6051 1000p HN1A01FU
FR– 4 OVER LOAD DETECT
SP2 FR– 3
CL6015
JL6011
IC6005 C6033
C6110
0.01
C6111
0.01
D6005
DA2J10100L JC6011
0
(R-CH) FR+ 2 +12V REGULATOR 1
CL6013 C6046 1000p CL6025
FR+ 1 IC6005
C6106 0.01 NJM2831F12(TE2)
C6093 R6056 C6092 C6097 R6073 C6105 C6104 C6096 R6063 C6095
D 0.1 100k 0.0022 10 47k 0.1 10 1000p 330k 47p
CONT
C6040 C6068
GND
CN6002 0.047 0.047
NC
7P
0
JL6006
1
2
3
(Page 47)
25.3
25.3
14.2
14.2
28.2
28.2
28.2
14.2
14.2
28.2
28.2
28.2
14.2
14.2
25.3
25.3
PVDD 7 R6074
JL6009 Q6003 R6069 R6075
33k
3.1
PVDD 6 LSCR523UBFS8TL 3.2 47k 47k
>01S CL6009
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
24
23
DC DETECT
PVDD 5
BST_A
BST_B
GND
GND
OUT_A
OUT_A
PVDD_AB
PVDD_AB
PVDD_AB
OUT_B
GND
GND
OUT_C
PVDD_CD
PVDD_CD
PVDD_CD
OUT_D
OUT_D
GND
GND
BST_C
BST_D
POWER NC 4 CL6024
C6011 C6016 C6019 R6006 C6099 R6064
JL6007
BOARD PGND 3 1000p 470 470 0.22 22 100 JL6032
CN902
IC6006
JL6010 35V 35V J6001
C6035 CL6026
E
PGND 2 SUBWOOFER
CL6010 0.001 WIRED CONNECTION
PGND 1 C6024 C6025 JL6033
1000p DIGITAL POWER AMP
10
50V IC6006
TAS5614LA-S C6098 JC6013
GVDD_CD
GVDD_AB
0
INPUT_C
INPUT_D
C-START
1000p
INPUT_A
INPUT_B
ET6001 L6003
OC_ADJ
FB6003 C6012
RESET
FAULT
2.2uH LN6005
DVDD
AVDD
IC6001
10
OTW
CL6011
GND
GND
GND
GND
CLIP
VDD
E
M1
M2
M3
CL6023
(CHASSIS) (CHASSIS)
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
DC/DC CONVERTER
ET6002
10
IC6001
IC6010
11.9
11.9
1.1
3.2
1.6
1.6
2.3
3.3
7.7
1.6
1.6
3.3
3.3
3.3
11.9
CL6021 RT7272BGSP
E
F 12.9 1 8 28.1 R6004 LOW-PASS FILTER

(CHASSIS) SW VIN 47k IC6010
17.2 2 7 0.3
R6065 NJM8065RB1(TE1)
LN6001 BOOT RLIM L6005
CL6001 2.2k
C6007 3.2 3 6 0.9 10uH
0.1 EN COMP 2.9 1 8 4.9
4 5 0.7 C6017
R6005 VCC
(CHASSIS) JC6023 GND FB 47k 2.9 2 7 2.9
L6001 0.0027 L6012
R6013 30k
0
C6049 0.1
R6014 47
R6018 47
R6020 47
R6021 47
JC6006 0
JC6007 0
22uH 10uH
C6050 1
C6060 1
R6025 0
2.9 3 6 2.9
CL6018
LN6003
CL6012 4 5 2.9
JL6004 R6001 R6002 R6003 VSS
C6008 D6001 C6002 C6003 C6036 C6037 C6045 C6039 C6069
27k 22k 3.3k
(CHASSIS) 0.001 UDZSUSTE-1715B 22 22 47 0.1 0.01 10 1
25V
G
C6034 C6001 C6030
CL6005 FB6001 47 1000p 0.1
25V
D6003
R6066 RB520SM-30T2R
5.6k C6100
680p
IC6002
FB6004
R6072 R6071 R6068
0 C6102 4.7k 1.5k
22
R6010 10k
DC/DC CONVERTER R6037 R6038 C6112 C6103

L6004 47 10k 1000p 680p
H 2.2uH IC6002
TPS563209DDCR 11
C6026 C6076 C6073 C6070 C6101 C6085
0.1 1 6 10.7
0.1 10 1 22 10
GND VBST
5.5 2 5 12.4
SW EN
12.7 3 4 0.7
CL6020
R6041
R6070
VIN VFB
10k
0 CN6005
R6054 28P
1k JL6031
PCON_ON
L6002
4.7uH R6007 R6008 28 PCON_ON
JL6008 47k 15k
27 DGND
I C6015 C6018 C6013 C6014 R6009

1.7
JL6030
26 AMP_D2(SL/SR)
3.2
1.6
1.6
1.6
1.6
3.2
3.2
3.2
FB6002 0.1 10 22 22 10k R6052
0
0
47 25 DGND
D2 JL6029
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
24 AMP_D2(C/SW)
C6006 C6020 C6023 C6028 C6031 R6050
TEST
SDOUT
NC_56
NC_55
NC_54
NC_53
VR_PWM
AVSS_PWM
AVDD_PWM
PWM_P_4
PWM_M_4
NC_47
NC_46
NC_45
NC_44
PWM_P_3
PWM_M_3
PWM_P_2
PWM_M_2
PWM_P_1
PWM_M_1
VALID
DVSS1_CORE
DVDD1_CORE
BKND_ERR
PSVC
LRCLKO
SCLKO
100 23 DGND
IC6004
0.001 1 1 10 47 JL6028
16V D0
22 AMP_D0(FL/FR)
IC6007
R6048
+3.3V REGULATOR 47 21 DGND
LRCK JL6027
IC6004 20 AMP_LRCK
RP114K331D-TRB STREAM PROCESSOR
C6021 R6045
19 DGND
DVDD2_CORE
1
DVSS2_CORE
IC6007 47
PWM_HPM_R
PWM_HPM_L
PWM_HPP_R
JL6026
J
PWM_HPP_L
D6002 3.2 3 2 BCK

ASEL_EMO2
RB520SM-30T2R TAS5534DGGR-S
CE GND 18 AMP_BCK
PLL_FLTM
OSC_RES
PLL_FLTP
5.1
VR_ANA
4 1 3.2
HP_SEL
VR_DIG
R6044
RESET
LRCLK
VDD VOUT 17 DGND
SDIN1
SDIN2
SDIN3
SDIN4
EMO1
MUTE
MCLK
AVDD
SCLK
AVSS
47 JL6025
PDN
SDA
MCK FFC4
SCL
C6005 C6022 16 AMP_MCK
1000p 0.001 R6043 MAIN
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
15 DGND
100 JL6024 BOARD
MUTE
14 AMP_MUTE (4/5)
0.6
1
1.7
3.2
0.2
1.8
0.9
3.2
3.2
3.2
3.2
3.2
2.5
3.2
1.6
0
0
1.8
C6029 C6032 R6042 100 JL6023
OVF1
IC6003
1 10 13 OVF1
CL6019
RESET R6040 100 JL6022

12 AMP_INIT
+5V REGULATOR DRIVER_SD R6039 100 JL6021
IC6003 IC6008 JL6020
11 DRIVER_SD
K 12 DC_PRT
C6075 0.0047
CN6001 RP130N501D-TR-FE
6P 10 DC_PRT
C6074 R6036 100 JL6019
0.047 BUFFER PCON_AMP
CL6002 JL6001
13
5.5 1 5 4.9 9 PCON_AMP
IC6008
R6033 10k
DCDC_12.5V 6 VDD VOUT PDN R6035 100 JL6018

CL6004 JL6002 2 TC7SZ125FU,RSOYJ 8 AMP_PDN
DCDC_12.5V_GND 5 GND
CL6006 JL6003 3.2 3 4 R6028 3.1
R6034
470 4 3 100
7 DGND
MAIN DCDC_5.5V 4 CE NC GND SDA JL6017
BOARD 2 1.7 6 AMP_SDA
(3/5) DCDC_5.5V 3 R6049
CL6008 JL6005 0 3.2
R6032
5 1 100
5 DGND
DCDC_5.5V_GND 2 VCC SCL JL6016
4 AMP_SCL
DCDC_5.5V_GND 1 PCON_1 R6031 100 JL6015
3 PCON_1
R6029 15k
R6030 18k
C6072 R6046
L 0.047 0
WIRED_DET
WIRED_ON
2 WIRED_DET
1 WIRED_ON
C6077 C6071 R6027 C6089 C6080 C6091 C6090 R6047 C6087 C6084
L6011
10uH
10 0.0047 470 10 10 10 0.1 150 1 0.01
C6078 L6010
470 10uH R6053
6.3V 0
WIRED_DET
DRIVER_SD
PCON_AMP
WIRED_ON
PCON_ON
PCON_1
DC_PRT
RESET
MUTE
LRCK
OVF1
MCK
PDN
SDA
BCK
SCL
D0
D2
Note: When the IC6006 on the SK1 AMP board or the SK1
AMP board is replaced, spread the compound to the
touching portion between the IC6006 and the heat sink.
HT-X9000F/XF9000
45 45
HT-X9000F/XF9000
5-10. PRINTED WIRING BOARD - POWER Board - • See page 41 for Circuit Boards Location. • : Uses unleaded solder.
1 2 3 4 5 6 7 8 9
POWER BOARD
IC902 JR901 JL908
R926
C921
R939 2
Q908 3
R938 1 A R920
A R927 C905 JL903
JW906
E 1 3 R922 R901
D910
R930 PH901
C926 C914 R940
JW909
R929 2 4 C902
R925
R924
R928 K Q901
JW908
JW904
E A
1
JW905
T901 JL909 D902 Q902
A K E
POWER TRANSFORMER R903
D918 E
R910 K
F902 C915 Q903
11 2 C901
1 C918 TH901
R914 A K K A VR901
JL914 D905 D904
(Page 42) C904
L902
10 R909 C912 LF901
>07P 3 R906 5 4 LINE FILTER
R913 F901
R902
MAIN C925 JL907
JW902
JW903
BOARD
B
D917
4 8 1
CN301
IC901
JW901
R919
CN902 A902
C913 K
A JL902
8 5 D908 LN901
R916
JL912 K A
R937
PATTERN SPARK-GAP
R936
R905 S 4
(Page 44) D913 Q907 JL901
7 6 C908
>01P JL906
D
1 3
SK1 AMP
G 2
BOARD C919 CN901
R915
CN6002 A D909
11
R911
JW910
C931 A C903 1
D919 C917
C923
JL911
C JL910
C929
R907 D911
K A901 3 C910
AC1
(AC IN)
TH902
K JL905
R908
ET902 ET901
C924 JL904
R923 12, 13
C920 C906
(CHASSIS)
1-982-475- (12, 13)
(CHASSIS)
HT-X9000F/XF9000
46 46
HT-X9000F/XF9000
5-11. SCHEMATIC DIAGRAM - POWER Board - • See page 48 for IC Block Diagrams.
1 2 3 4 5 6 7 8 9 10 11 12
POWER BOARD JL910

ET902
E
ET901
JL905
(CHASSIS)
E
CN902
JL904 11P
(CHASSIS) JL911
C924 11 PGND (Page 45)
0.01
CN901 F901
LF901
C910
0.0022
C906
0.0022 2
D909
D2SB60A-7003
10 PGND
>01S
3P 5A 9 PGND
LINE 250V 250V JL912
JL901 250V JL903 FILTER ~ C923 C926 C925 C918 SK1 AMP
4 3 2200 8 PVDD BOARD
LIVE 1 – + D913 47 47 47
AC1 35V 35V 35V 35V CN6002
B ~ FMX-22SL 7 PVDD
R923
(AC IN) NC 2 0.33
1 1W 6 PVDD
NEUTRAL 3 LN901 C908 R916
PATTERN 0.1 1.5M 5 DGND
SPARK-GAP C902 310V 0.5W L902
4 HI-TEMP/VACS_REQ
VR901 0.22 JL914 MAIN
310V 3 PVDD_SEL BOARD
(5/5)
A901 JL902 TH902 2 NC
R928
100 1 D28.5V
C917 C920 F902
(HEATSINK) 470p
150 1A
400V 250V R929 250V
C C903
0.01
C929
2.2k
D917 R936 R939
UDZSUSTE-172.4B 0.056 470p 100
1W 250V R930
C901 C921 R926 47k
0.01 0.1 47k
R905
47k
R915 R914 C913 R907 C919
100k 1k 0 330p 47k 0.0047
TH901 S
1kV 250V
0
R908 C931
Q901 R911 0.3 47k 0.0047
D LSCR523UBFS8TL 47 Q907 250V
26.6
19.7
2.4
R6015KNXC7 R927
OVERHEAT DETECT 150.7
4.7k
POWER ON D911
SWITCH
1
2
R901 R906 R909 D905 SARS05
180k 47k 220 DB2J31700L
K
VREF
D919
SARS05
IC902
C905 R910 SHUNT REGULATOR
0.01 330k
T901 IC902
R937 MM1431FNRE
22 POWER
163.5
2W TRANSFORMER
19.8
E 6 7
0.4
JL907 JL906
8
7
5 8
A
OUT
VH
NC
VCC
3
19.8 IC901 4
POWER CONTROL
19.7 IC901
BM1Q002FJ-E2 10
Q903
LTA014EUBFS8TL 0.4
F PROTECT SWITCH 2 11 0
GND
R940
CS
FB
ZT
CRH02(T5R,SONY,XM)
1k
1 3.2
1
2
R938 Q908
1k LTC014EUBFS8TL
D910
0.3
0.4
0
PVDD CONTROL SWITCH
C912 D918 C915

0.1 DZ2J240M0L 10
R902
4.7k JR901 R920 R922
G 0 39k 10
D904 R919
UDZSUSTE-1730B 4.7k
R903 C904 D908 PH901

220k 47 DA2J10100L EL816S1(B)(TA)(DTE-S) R925
470
JL908 ISOLATOR 1 27.6
0.4 3
R924
H 19.7
Q902
LSCR523UBFS8TL
D902
DZ2J039M0L
R913
33k C914
0.0047
JL909 4 2 26.6 1k
PROTECT DETECT
HT-X9000F/XF9000
47 47
HT-X9000F/XF9000
• Waveforms • IC Block Diagrams
– SK1-WS-CHUKEI Board – – SK1-WS-CHUKEI Board –

IC1501 MM3411A33URE
IC1502 4
1
4 VDD
CE 1 BIAS
VOLTAGE
–
REFERENCE
+
3.3 Vp-p
324 ns CURRENT
LIMIT 3 VOUT
1 V/DIV, 200 ns/DIV

GND 2
– SK1 AMP Board –

– SK1 AMP Board –
IC6001 2 (BOOT)
0 IC6001 RT7272BGSP IC6002 TPS563209DDCR
VBST
VFB
VA
EN
VCC 6 5 4
8 VIN REF VOLTAGE

REFERENCE
CURRENT INTERNAL
SENSE OSCILLATOR VCC
REGULATOR V UVP V OVP SS
SOFT START
AMPLIFIER SLOPE
34 Vp-p SW 1 COMP
+
+
–
–
+
BOOT 2 6 FOLDBACK VA VCC
2 Ps
CONTROL
SHUTDOWN
UVP OVP PWM
COMPARATOR 7 RLIM
10 V/DIV, 2 Ps/DIV Q S
+ 0.4V + 1.2V
TON
ONE-SHOT
UV

UV
TSD
IC6002 6 (VBST)
qa
COMPARATOR
CONTROL
6 COMP
+ LOGIC UVLO
EN 3 Q R
LOCKOUT
OCL OCL
GND 4 CURRENT COMPARATOR – THRESHOLD
COMPARATOR +
+ 1.7V
XCON
SS
+ 0.8V
EA +
5 FB LS VREG5 HS
VREG5
17.4 Vp-p
1.4 Ps REGULATOR
5 V/DIV, 1 Ps/DIV
1 2 3
IC6007 wd SCLK
GND
SW
VIN
qs
IC6003 RP130N501D-TR-FE IC6004 RP114K331D-TRB
VOUT 1 4 VDD
3.3 Vp-p VCC 1 5 VOUT
324 ns
1 V/DIV, 200 ns/DIV GND 2
VREF
IC6008 4
qd VREF CURRENT
LIMIT
CURRENT
LIMIT
GND 2 3 CE
4 NC
CE 3
4.4 Vp-p IC6005 NJM2831F12 (TE2)

41 ns
VOUT
VIN
2 V/DIV, 20 ns/DIV
5 4
THERMAL
PROTECTION
BANDGAP
REFERENCE
1 2 3
CONTROL
GND
NC
HT-X9000F/XF9000
48 48
HT-X9000F/XF9000
IC6006 TAS5614LA-S
GVDD_AB 1 44 BST_A
43 BST_B
VDD 2
42 GND
OC_ADJ 3
41 GND
RESET 4
ANALOG + PWM & TIMING GATE- 40 OUT_A
PWM LOOP FILTER CONTROL DRIVE
INPUT_A 5 – 39 OUT_A
RECEIVER
38 PVDD_AB
37 PVDD_AB
36 PVDD_AB
PWM
INPUT_B 6 ANALOG + PWM & TIMING GATE-
RECEIVER 35 OUT_B
C_START 7 LOOP FILTER – CONTROL DRIVE
34 GND
DVDD
DVDD 8
GND 9
GND 10
GND 11
GND 12
AVDD 33 GND
AVDD 13
ANALOG + PWM & TIMING GATE-
PWM 32 OUT_C
INPUT_C 14 LOOP FILTER – CONTROL DRIVE
RECEIVER
31 PVDD_CD
30 PVDD_CD
29 PVDD_CD
PWM
INPUT_D 15 ANALOG + PWM & TIMING GATE- 28 OUT_D
RECEIVER
LOOP FILTER – CONTROL DRIVE 27 OUT_D
26 GND
25 GND
24 BST_C
23 BST_D
STARTUP CB3C OVER-LOAD

CONTROL PROTECTION
TEMP
SENSE
FAULT 16
OTW 17 PROTECTION
POWER-UP
&
CLIP 18 RESET
I/O LOGIC
M1 19
M2 20 BST_X
M3 21 GVDD_X
UVP
GVDD_CD 22 AVDD
DVDD
IC6007 TAS5534DGGR-S
PWM_HPM_L 1
PWM_HPP_L 2
PWM_HPM_R 3
PWM_HPP_R 4
AVSS 5
PLL_FLTM 6
PLL_FLTP 7
VR_ANA 8
AVDD 9
ASEL_EMO2 10
MCLK 11
OSC_RES 12
DVSS2_CORE 13 POWER
SUPPLY
DVDD2_CORE 14
56 N.C.
EMO1 15 55 N.C.
RESET 16 54 N.C.
HP_SEL 17 DEVICE 53 N.C.
PDN 18 CONTROL 52 VR_RWM
MUTE 19 51 AVSS_PWM
50 AVDD_PWM
49 PWM_P_4
I2C SERIAL 48 PWM_M_4
SDA 20
CONTROL DIGITAL 47 N.C.
SCL 21 INTERFACE PWM
AUDIO 46 N.C.
SECTION
PROCESSOR 45 N.C.
44 N.C.
43 PWM_P_3
42 PWM_M_3
41 PWM_P_2
40 PWM_M_2
LRCLK 22 CLOCK, PLL, 39 PWM_P_1
SCLK 23 AND 38 PWM_M_1
SDIN1 24 SERIAL DATA 37 VALID
SDIN2 25 INTERFACE 36 DVSS1_CORE
SDIN3 26 35 DVDD1_CORE
SDIN4 27 34 BKND_ERR
VR_DIG 28 33 PSVC
32 TEST
31 LRCLKO
30 SCLKO
29 SDOUT
49
HT-X9000F/XF9000
– POWER Board –
IC901 BM1Q002FJ-E2
VCC
OUT
N.C.
VH
8 7 6 5
STARTER
+ VCC
13.0V/ 1SHOT + UVLO 4.0V 12V CLAMP
13.5V/ VREF
8.7V REGULATOR CIRCUIT
8.2V
+ VCC
100mV TIME + OVP
/200mV ZT OUT
27.5V
COMP. TRIGGER
DETECT PRE
VREF LOGIC S Q
DRIVER
R
ZT BLANKING MAX FREQUENCY
OUT CONTROL
BURST COMP. DELAY STOP

+ TIMER TIMER
0.50V
ZT ACSNS
OLP
+ COMP. + OSC
2.6V/2.8V
ZT OVP DCDC SOFT

VREF
+ COMP. COMP. START
0.50V
5.0V +
CURRENT SENSE LEADING EDGE
BLANKING
1 2 3 4
ZT
FB
CS
GND
50
HT-X9000F/XF9000
SECTION 6
EXPLODED VIEWS
Note:
• -XX and -X mean standardized parts, so • The mechanical parts with no reference
The components identified by mark 0
they may have some difference from the number in the exploded views are not sup-
or dotted line with mark 0 are critical for
original one. plied.
safety.
• Items marked “*” are not stocked since • Color Indication of Appearance Parts Ex-
Replace only with part number specified.
they are seldom required for routine ser- ample:
vice. Some delay should be anticipated KNOB, BALANCE (WHITE) . . . (RED) Les composants identifiés par une marque
when ordering these items.   0 sont critiques pour la sécurité.
Parts Color Cabinet’s Color Ne les remplacer que par une pièce por-
tant le numéro spécifié.
The components identified by mark 9 con-

tain confidential information.
6-1. FOOT SECTION Strictly follow the instructions whenever the
components are repaired and/or replaced.
Les composants identifiés par la marque
9 contiennent des informations confiden-
tielles.
Suivre scrupuleusement les instructions
chaque fois qu’un composant est remplacé
et / ou réparé.
top side
rear side
left side
#2
#2
top cabinet section
#2 B
A
#2 not supplied
#2
not supplied
1 #2 B
1 A
#2
#2
bottom cabinet section

#2 #2
#1 #2
front side #2
2
#1 #2
#2
#2
#2 right side
– Bottom view – #2 2 rear side
1 1 #2
1 1 1
1
#2
#2 #1 #2
right side front side left side
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
1 4-597-760-01 CUSHION FOOT #1 7-685-645-79 SCREW +BVTP 3X6 TYPE2 IT-3
2 4-693-812-01 FOOT, RUBBER #2 7-685-647-79 SCREW +BVTP 3X10 TYPE2 IT-3
51
HT-X9000F/XF9000
6-2. TOP CABINET SECTION
FFC1
#3
#3
FP1 51
left side
C
FFC2
#2
not supplied
#2
SP1 front side

#2
#2
not supplied top side
#2
rear side #2
not supplied SP2 right side
#2 #2
51 A-2186-967-A SK1 LED BOARD, COMPLETE SP1 1-859-248-11 LOUDSPEAKER (35X93 mm) (Front L-ch)
FFC1 1-912-605-11 FFC (MB~SK1-LED-CHUKEI) (16P) (L = 107 mm)
FFC2 1-912-606-11 FFC (SK1-LED-CHUKEI~SK1-TOUCH) (6P) SP2 1-859-248-11 LOUDSPEAKER (35X93 mm) (Front R-ch)
(L = 50 mm) #2 7-685-647-79 SCREW +BVTP 3X10 TYPE2 IT-3
FP1 A-2201-999-A SERVICE ASSY, CABINET (TOP) #3 7-685-646-71 SCREW +BVTP 3X8 TYPE2 IT-3
(Including SK1-TOUCH board)
52
HT-X9000F/XF9000
6-3. BOTTOM CABINET SECTION
#2
#3 #3
top side #3
101
#3
not supplied
#3
#2 #3
#2 MAIN board section #3
E #3
#2
not supplied
#2
AC1
#2
not supplied #2 102 rear side
#3
not supplied BT1
FFC3
E
D
left side not supplied
#3
not supplied
#3
#3 not supplied
not supplied D #3
not supplied
(SK1-WS-CHUKEI board) #3
not supplied
not supplied
front side not supplied
not supplied right side
Note: When the bluetooth module (Ref. No. BT1) is replaced, be sure
to refer to “WIRELESS CONNECTION (LINK) WORK OF
BAR SPEAKER AND SUBWOOFER” on page 6.
101 A-2186-968-A SK1 IR REP (2) BOARD, COMPLETE BT1 1-493-368-11 BLUETOOTH MODULE (See Note)
0 102 4-966-267-12 BUSHING (FBS001), CORD FFC3 1-912-607-11 FFC (SK1-WS-CHUKEI~AIROHA) (18P)
0 AC1 1-837-308-12 CORD, POWER-SUPPLY (X9000F: US, CND) (L = 75 mm)
0 AC1 1-912-340-11 POWER-SUPPLY CORD (XF9000: AEP) #2 7-685-647-79 SCREW +BVTP 3X10 TYPE2 IT-3
0 AC1 1-912-341-11 POWER-SUPPLY CORD (XF9000: UK) #3 7-685-646-71 SCREW +BVTP 3X8 TYPE2 IT-3
53
HT-X9000F/XF9000
6-4. MAIN BOARD SECTION
#4
#4
#4
#4
not supplied top side
#3 #3
#3
#3
#3 not supplied
#3
Note 1: The parts for repair of the radiation sheet
#3
(Ref. No. 154, 155) are larger than the
156 radiation sheet before replacement.
155 154
156 When replacing the radiation sheet
(Ref. No. 154, 155), make sure to cut it
F to the sizes below.
H
I
153 J
H
K
G W
152 152
Ref. No. W H
151
154 8.0 8.0
155 14.0 14.0
unit: mm
not supplied
#3 G
left side #4 #4
H
I
J K
rear side
F
SK1 AMP board section
front side
right side
Note 2: When the complete MAIN board (Ref. No. 153) is replaced,
be sure to refer to “SERIAL NUMBER WRITING WORK
WHEN THE MAIN BOARD REPLACED” on page 5.
151 4-589-900-01 SHEET, RADIO WAVE ABSORPTION 154 4-699-695-61 SHEET RADIATION (See Note 1)
152 4-586-625-11 GASKET (SL) 155 4-699-695-61 SHEET RADIATION (See Note 1)
9 153 A-2207-315-A MAIN BOARD, COMPLETE (SV) 156 4-699-695-61 SHEET RADIATION (34.0X16.0 mm)
(X9000F: US, CND) (See Note 2) #3 7-685-646-71 SCREW +BVTP 3X8 TYPE2 IT-3
9 153 A-2207-317-A MAIN BOARD, COMPLETE (SV) (XF9000: AEP) #4 7-682-546-09 SCREW +B 3X5
(See Note 2)
9 153 A-2207-318-A MAIN BOARD, COMPLETE (SV) (XF9000: UK)
(See Note 2)
54
HT-X9000F/XF9000
6-5. SK1 AMP BOARD SECTION
#3
204 top side
#3
not supplied
203 L
#3 not supplied
#3
#3
#3
L #3
#3
#3
#2 not supplied not supplied

not supplied #2
Note 1: The parts for repair of the radiation sheet

#3 #3 (Ref. No. 201) is larger than the radiation
not supplied sheet before replacement.
FFC4
#3 When replacing the radiation sheet
not supplied #3 (Ref. No. 201), make sure to cut it to the
(SK1-JACK board) sizes below.
#3
#3
202
left side W
201 201 Ref. No. W H
201
201 14.0 10.0
201
rear side
unit: mm
POWER board section
front side
right side
Note 2: When the complete SK1 AMP board (Ref. No. 202) is re-
placed, spread the compound to the touching portion between
the IC6006 and the heat sink.
201 4-699-695-61 SHEET RADIATION (See Note 1) #2 7-685-647-79 SCREW +BVTP 3X10 TYPE2 IT-3
202 A-2186-964-A SK1 AMP BOARD, COMPLETE (See Note 2) #3 7-685-646-71 SCREW +BVTP 3X8 TYPE2 IT-3
203 4-699-695-21 SHEET RADIATION (20.0X20.0 mm)
204 A-2186-968-A SK1 IR REP (1) BOARD, COMPLETE
FFC4 1-912-604-11 FLEXIBLE FLAT CABLE (MB~AMP) (28P)
(L = 60 mm)
55
HT-X9000F/XF9000
6-6. POWER BOARD SECTION
#3 top side
#3
#3
251
#3 not supplied
not supplied
left side
not not supplied

supplied
not supplied
rear side
not supplied
not supplied not supplied
front side not

supplied
right side
not supplied
not supplied
251 A-2186-843-A POWER BOARD, COMPLETE #3 7-685-646-71 SCREW +BVTP 3X8 TYPE2 IT-3
56
HT-X9000F/XF9000
SECTION 7
MAIN POWER SK1 AMP
ELECTRICAL PARTS LIST
Note:
• Due to standardization, replacements in • SEMICONDUCTORS
The components identified by mark 9 con-
the parts list may be different from the In each case, u: μ, for example:
tain confidential information.
parts specified in the diagrams or the com- uA. . : μA. . , uPA. . , μPA. . ,
Strictly follow the instructions whenever the
ponents used on the set. uPB. . : μPB. . , uPC. . , μPC. . ,
components are repaired and/or replaced.
• -XX and -X mean standardized parts, so uPD. . : μPD. .
they may have some difference from the When indicating parts by reference num- Les composants identifiés par la marque
original one. ber, please include the board name. 9 contiennent des informations confiden-
• Items marked “*” are not stocked since tielles.
they are seldom required for routine ser- The components identified by mark 0 Suivre scrupuleusement les instructions
vice. Some delay should be anticipated or dotted line with mark 0 are critical for chaque fois qu’un composant est remplacé
when ordering these items. safety. et / ou réparé.
• RESISTORS Replace only with part number specified.
All resistors are in ohms. Among mounted electrical parts on each
METAL: Metal-film resistor. Les composants identifiés par une marque boards, only parts that are described in
METAL OXIDE: Metal oxide-film resistor. 0 sont critiques pour la sécurité. the electrical parts list can be replaced for
F: nonflammable Ne les remplacer que par une pièce por- repair.
• CAPACITORS tant le numéro spécifié. The parts that are not described in the
uF: μF electrical parts list cannot be replaced with
• COILS single for repairing.
uH: μH
9 A-2207-315-A MAIN BOARD, COMPLETE (SV) < COIL >
(X9000F: US, CND)
9 A-2207-317-A MAIN BOARD, COMPLETE (SV) (XF9000: AEP) 0 LF901 1-460-975-11 CHOKE COIL (SSR21NVS-M12220)
9 A-2207-318-A MAIN BOARD, COMPLETE (SV) (XF9000: UK)
******************** < PHOTO COUPLER >
When the MAIN board is defective, replace the complete mounted board. 0 PH901 6-600-883-01 PHOTO COUPLER EL816S1 (B) (TA) (DTE-S)
When the MAIN board is replaced, be sure to refer to “SERIAL NUMBER WRITING < TRANSISTOR >
WORK WHEN THE MAIN BOARD REPLACED” on page 5.
************************************************************* 0 Q901 6-552-892-01 TRANSISTOR LSCR523UBFS8TL
0 Q902 6-552-892-01 TRANSISTOR LSCR523UBFS8TL
A-2186-843-A POWER BOARD, COMPLETE 0 Q903 6-552-922-01 TRANSISTOR LTA014EUBFS8TL
********************** 0 Q907 6-553-768-01 FET R6015KNXC7
Q908 6-552-936-01 TRANSISTOR LTC014EUBFS8TL
7-685-646-71 SCREW +BVTP 3X8 TYPE2 IT-3
< TRANSFORMER >
< CONNECTOR >
0 T901 1-697-594-11 SWITCHING TRANSFORMER (ST6444)
0 * CN901 1-793-660-11 PIN, CONNECTOR (PC BOARD) 3P
< THERMISTOR >
< DIODE >
0 TH901 1-812-011-11 THERMISTOR, POSITIVE
0 D902 6-503-011-01 DIODE DZ2J039M0L 0 TH902 1-811-795-31 NTC THERMISTOR SCK13045LMY501
0 D904 8-719-083-71 DIODE UDZSUSTE-1730B
0 D905 6-503-058-01 DIODE DB2J31700L < VARISTOR >
0 D908 6-502-961-01 DIODE DA2J10100L
0 D910 6-503-775-01 DIODE CRH02 (T5R, SONY, XM) 0 VR901 1-811-165-31 VARISTOR (TVR10471-D)
*************************************************************
0 D911 6-503-900-01 DIODE SARS05
D913 6-501-849-01 DIODE FMX-22SL A-2186-964-A SK1 AMP BOARD, COMPLETE (See Note)
0 D917 6-500-694-01 DIODE UDZSUSTE-172.4B ***********************
0 D919 6-503-900-01 DIODE SARS05
< CONNECTOR >
< FUSE >
CN6001 1-770-470-21 PIN, CONNECTOR (PC BOARD) 6P
0 F901 1-523-067-51 FUSE (5 A/250 V) CN6002 1-785-728-21 PIN (PC BOARD), CONNECTOR 7P
0 F902 1-523-082-11 FUSE (1 A/250 V) CN6003 1-764-250-21 PIN, CONNECTOR (PC BOARD) 4P
CN6004 1-779-993-11 PIN, CONNECTOR (PWB) 5P
< IC > CN6005 1-820-841-31 CONNECTOR, FFC/FPC (LIF) 28P
0 IC901 6-723-132-01 IC BM1Q002FJ-E2 < DIODE >

IC902 6-716-865-01 IC MM1431FNRE
D6001 8-719-083-83 DIODE UDZSUSTE-1715B
< JUMPER RESISTOR > * D6002 6-503-578-01 DIODE RB520SM-30T2R
* D6003 6-503-578-01 DIODE RB520SM-30T2R
0 JR901 1-216-295-91 SHORT CHIP 0 D6005 6-502-961-01 DIODE DA2J10100L
D6006 6-503-040-01 DIODE DZ2J300M0L
Note: When the complete SK1 AMP board is replaced, spread the
compound to the touching portion between the IC6006 and the
heat sink.
57
HT-X9000F/XF9000
SK1 AMP SK1 IR REP (1) SK1 IR REP (2) SK1-JACK SK1 LED SK1-TOUCH SK1-WS-CHUKEI
< FUSE > < JACK >
0 F6001 1-523-395-11 FUSE (5 A/32 V) J1602 1-843-401-31 JACK, STEREO (MINI TYPE) (ANALOG IN)
0 F6002 1-523-395-11 FUSE (5 A/32 V) *************************************************************
< FERRITE BEAD > A-2186-967-A SK1 LED BOARD, COMPLETE

***********************
FB6001 1-400-180-21 INDUCTOR, EMI FERRITE (1608)
FB6002 1-400-179-21 INDUCTOR, EMI FERRITE (1608) When the SK1 LED board is defective, replace the complete mounted board.
FB6003 1-400-180-21 INDUCTOR, EMI FERRITE (1608) The mounted parts cannot be replaced with single for repairing.
FB6004 1-400-180-21 INDUCTOR, EMI FERRITE (1608) *************************************************************
< IC > SK1-TOUCH BOARD

****************
IC6002 6-722-479-01 IC TPS563209DDCR
IC6003 6-715-842-01 IC RP130N501D-TR-FE When the SK1-TOUCH board is defective, replace the cabinet (top) assy (Ref. No.
IC6004 6-723-719-01 IC RP114K331D-TRB FP1).
IC6005 6-710-731-01 IC NJM2831F12 (TE2) *************************************************************
IC6006 6-723-248-01 IC TAS5614LA-S (See Note 1)
SK1-WS-CHUKEI BOARD
IC6007 6-723-247-01 IC TAS5534DGGR-S *******************
IC6008 6-715-041-01 IC TC7SZ125FU, RSOYJ
< CONNECTOR >
< JACK >
CN1501 1-821-139-11 HEADER ASSEMBLY FOR PWB 12P
J6001 1-843-401-31 JACK, STEREO (MINI TYPE) CN1502 1-820-839-31 CONNECTOR, FFC/FPC (LIF) 18P
(SUBWOOFER WIRED CONNECTION)
< IC >
< JUMPER RESISTOR >
IC1501 6-719-198-01 IC MM3411A33URE
JC6006 1-216-864-91 SHORT CHIP 0 * IC1502 6-722-068-01 IC 74LCX541FT
JC6007 1-216-864-91 SHORT CHIP 0 *************************************************************
JC6011 1-216-864-91 SHORT CHIP 0
JC6013 1-216-864-91 SHORT CHIP 0 MISCELLANEOUS
JC6023 1-216-864-91 SHORT CHIP 0 **************
< TRANSISTOR > 0 AC1 1-837-308-12 CORD, POWER-SUPPLY (X9000F: US, CND)
0 AC1 1-912-340-11 POWER-SUPPLY CORD (XF9000: AEP)
Q6001 8-729-013-22 TRANSISTOR HN1A01FU 0 AC1 1-912-341-11 POWER-SUPPLY CORD (XF9000: UK)
Q6002 8-729-013-22 TRANSISTOR HN1A01FU BT1 1-493-368-11 BLUETOOTH MODULE (See Note 2)
Q6003 6-552-892-01 TRANSISTOR LSCR523UBFS8TL FFC1 1-912-605-11 FFC (MB~SK1-LED-CHUKEI) (16P) (L = 107 mm)
*************************************************************
FFC2 1-912-606-11 FFC (SK1-LED-CHUKEI~SK1-TOUCH) (6P)
A-2186-968-A SK1 IR REP (1) BOARD, COMPLETE (L = 50 mm)
**************************** FFC3 1-912-607-11 FFC (SK1-WS-CHUKEI~AIROHA) (18P)
(L = 75 mm)
When the SK1 IR REP (1) board is defective, replace the complete mounted board. FFC4 1-912-604-11 FLEXIBLE FLAT CABLE (MB~AMP) (28P)
The mounted parts cannot be replaced with single for repairing. (L = 60 mm)
************************************************************* FP1 A-2201-999-A SERVICE ASSY, CABINET (TOP)
(Including SK1-TOUCH board)
A-2186-968-A SK1 IR REP (2) BOARD, COMPLETE SP1 1-859-248-11 LOUDSPEAKER (35X93 mm) (Front L-ch)
****************************
SP2 1-859-248-11 LOUDSPEAKER (35X93 mm) (Front R-ch)
When the SK1 IR REP (2) board is defective, replace the complete mounted board. *************************************************************
*************************************************************
SK1-JACK BOARD
**************
< CONNECTOR/JACK >
CN1601 1-778-965-21 CONNECTOR 12P

* CN1602 1-843-199-11 USB CONNECTOR ( )
CN1604 1-843-541-11 OPTICAL RECEIVER JACK (TV IN (OPT))
< FERRITE BEAD >
FB1601 1-481-467-11 BEAD, FERRITE (CHIP)

FB1602 1-481-467-11 BEAD, FERRITE (CHIP)
FB1603 1-400-851-11 EMI, FERRITE (SMD) (1005)
FB1604 1-481-253-21 FERRITE, EMI (SMD) (1005)
Note 1: When the IC6006 on the SK1 AMP board is replaced, spread Note 2: When the bluetooth module (Ref. No. BT1) is replaced, be
the compound to the touching portion between the IC6006 sure to refer to “WIRELESS CONNECTION (LINK) WORK
and the heat sink. OF BAR SPEAKER AND SUBWOOFER” on page 6.
58
HT-X9000F/XF9000
Ref. No. Part No. Description Remark

ACCESSORIES
************
4-725-865-12 MANUAL, INSTRUCTION (Operating Instructions)

(ENGLISH, SPANISH, FRENCH)
(X9000F: US, CND)
(ENGLISH) (XF9000: UK)
(FRENCH, SPANISH, DUTCH) (XF9000: AEP)
(GERMAN, ITALIAN, POLISH) (XF9000: AEP)
501 1-493-354-11 REMOTE COMMANDER (RMT-AH401U)

(Remote control)
502 1-837-197-31 CORD, LIGHT PLUG (Optical digital cable)
(XF9000: AEP, UK)
503 1-849-300-11 CABLE WITH CONNECTOR
(HDMI cable (supports the specification equal to
Premium High Speed HDMI Cable with Ethernet))
(X9000F: US, CND)
(XF9000: AEP, UK)

501 502
Remote control (1) Optical digital cable (1)
(X9000F: US, CND)

503
HDMI cable (supports the specification equal to Premium
High Speed HDMI cable with Ethernet) (1)
59
HT-X9000F/XF9000
REVISION HISTORY
Ver. Date Description of Revision

1.0 2018.01 New
How to search for a contact point of signal lines or the like in DIAGRAMS SECTION
If a contact point of a BLOCK DIAGRAM, PRINTED WIRING BOARD or SCHEMATIC DIAGRAM is shown in a different page, use
the PDF file search function to find one.
e.g.) If a contact point is shown as , follow the procedure below.

Procedure:
1. Press the [F] key while pressing the [Ctrl] key.
2. Input “>001Z” in the search box and press the [Enter] key.
3. The relevant part (page), where the contact point is shown, appears.
Note: If you still see the original page, press the [Enter] key again.

Service Manual: Sound Bar Active Speaker System

Uploaded by

Copyright:

Service Manual: Sound Bar Active Speaker System

Uploaded by

Document Information

Original Title

Copyright

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Service Manual: Sound Bar Active Speaker System

Uploaded by

Copyright:

HT-X9000F/XF9000 SA-X9000F/XF9000

SERVICE MANUAL US Model

• All of the units included in the HT-X9000F

COMPONENT MODEL NAME

harmonic distortion from 250mW to 220 V - 240 V AC, 50 Hz/60 Hz

rated output. (XF9000: AEP, UK)

POWER OUTPUT (reference) Power consumption

Front L/Front R speaker blocks: 100W On: 38W

Front L + Front R: 60W + 60W 0.5W

Compatible BLUETOOTH profiles 2) Dimensions* (approx.) (w/h/d) t4UBSUVQ(VJEF

Copyrights and Trademarks NOTES ON CHIP COMPONENT REPLACEMENT

“PlayStation” is a registered trademark or

Windows Media is either a registered

ATTENTION AU COMPOSANT AYANT RAPPORT

LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0 SUR

1. SERVICING NOTES ............................................. 4 5. DIAGRAMS

UNLEADED SOLDER ABOUT THE PROTECTION

NOTE OF REPLACING THE FUSE

– POWER Board (Conductor Side) –

NOTE OF PERFORMING THE OPERATION CHECK IN

2. Connect this unit with TV monitor.

15. Press the [ ] button on the remote commander, the service

6. Press the [V]/[v] buttons on the remote commander to select

Serial number Editor

(Displayed characters in the above figure are example)

RESETTING THE SYSTEM SPREADING OF COMPOUND

4 Select the menu item you want to

NOTE OF REPLACING THE MAIN BOARD FOR RE-

NOTE OF REPLACING THE ELECTRICAL PARTS ON

2-1. DISASSEMBLY FLOW

2-2. TOP/BOTTOM CABINET BLOCK-1 2-21. MAIN BOARD SERVICE POSITION

2-3. TOP/BOTTOM CABINET BLOCK-2 Top cabinet block

Bottom cabinet block

2-10. SK1-WS-CHUKEI BOARD

2-12. MAIN CHASSIS BLOCK-1 2-7. LOUDSPEAKER (L-ch/R-ch),

2-13. MAIN CHASSIS BLOCK-2

2-14. POWER-SUPPLY CORD 2-15. MAIN BOARD-1

2-16. MAIN BOARD-2

2-17. SK1 IR REP (1) BOARD

Note: Follow the disassembly procedure in the numerical order given.

2-2. TOP/BOTTOM CABINET BLOCK-1

soft cloth, etc.

top cabinet block

4 Remove the top cabinet block

3 Lift up the top cabinet left side

1 First install the front side of the top

2 Open to the outer side with your

2-3. TOP/BOTTOM CABINET BLOCK-2

soft cloth, etc.

top cabinet block

5 top cabinet block

4 speaker connection cable

3 speaker connection cable

6 bottom cabinet block

heatsink CN3004 terminal

SK1 AMP board Bend. Bend.

2-4. SK1 LED BOARD

Note 1: Check that the speaker connection

Hold down. Hold down.

5 SK1 LED board

boss 3 Remove the SK1 LED board block

+RZWRLQVWDOOWKH))& 3 A 1 FFC (6P)

front side top cabinet block

+RZWRLQVWDOOWKH))&3 A 1 FFC (6P)

,QVWDOODWLRQGLUHFWLRQIRUWKHORXGVSHDNHUIRU/FK boss

))&3VHWWLQJ

:LUHVHWWLQJ catcher rear side catcher

Note about installing the main chassis block

:LUHVHWWLQJ rear side