Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd
Upload
6K views

Shell Structures

Shell structures are light weight constructions using shell elements. A thin shell is defined as a shell with a thickness which is small compared to its other dimensions. The ideal thin shell must be capable of developing both tension and compression.

Uploaded by

Bhavani Rani
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
6K views

Shell Structures

Shell structures are light weight constructions using shell elements. A thin shell is defined as a shell with a thickness which is small compared to its other dimensions. The ideal thin shell must be capable of developing both tension and compression.

Uploaded by

Bhavani Rani
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 3

c 

c  are 
 
 constructions using
shell elements. These elements are    and
are assembled to 
. Typical applications
are fuselages of aeroplanes, boat hulls and roof
structures in some buildings.

A thin shell is defined as a shell with a thickness which is


small compared to its other dimensions and in which
deformations are not large compared to thickness. A
    between a  and a
 is that, in the , the  
 has   
 .

Montréal Biosphere Buckminister filler,canada

Membrane action in a shell is primarily caused by in-plane forces (plane stress), though there may be
secondary  
 . Where a flat plate acts similar to a beam with bending
and shear stresses, shells are analogous to a cable which resists loads through tensile stresses. Though the ideal
thin shell must be capable of developing both tension and compression

Shell structure of the TWA Flight Center


Building by ¦  , John F. Kennedy
International Airport, New York

Nicholas Grimshaw, Eden Project, Cornwall, UK




  

Ú Folded plate
Ú Barrel vaults
Ú Short shells
Ú £omes
Ú Intersection shells
Ú Warped surfaces
Ú Shell arches

a 
The distinguishing feature of the folded plate is the
ease in forming plane surfaces. Therefore, they are
more adaptable to smaller areas than curved
surfaces which require multiple use of forms for
maximum economy. A folded plate may be formed
for about the same cost as a horizontal slab and has
much less steel and concrete for the same spans.
Folded plates are not adapted to as wide bay
spacings as barrel vaults. For widths of plate over,
say, 12 feet, the thickness of the folded plate must
be thicker than for a barrel vault. Some advantage
may be gained by increasing the thickness of the slab
just at the valleys so it will act as a haunched beam and as an I section plate girder.

 
  
×    

   

 
     
 
     
   

 
    


  ×       


    

   
   
 
 
  
      
   
 
        
 

 

 
   

    

 

   


   
! 
     



     
! 


  

       

  "     


  "   
 

 
   

£ 
A dome is a space structure covering a more or less square or circular area. The best known example is the dome of
revolution, and it is one of the earliest of the shell structures. Excellent examples are still in existence that were built in
Roman times. They are formed by a surface generated by a curve of any form revolving about a vertical line. This surface
has double curvature and the resulting structure is much stiffer and stronger than a single curved surface, such as a
cylindrical shell. The simples dome of revolution is a portion of a sphere. However, other curves are also satisfactory, such
as the ellipse, the parabola, other conic sections, or random curves.

ë     
The structural efficiency of the intersection shell depends on the angle of the intersection of the surfaces. If the angle is
small (called here for descriptive purposes, sharp), then a natural rib is formed by the adjacent elements of the basic
shells which is much stiffer than the adjacent shells on each side. An itersection for which the angle is very large is called
here a shallow intersection. An intersection of 90 degrees is the optimum value because it gives a stiff rib. On large
structures with shallow intersections, massive ribs may be necessary which are very evident and detract from the light
appearance.

  
Shell arches are somewhat in the same category as short shells in that the shell action is subservient to the arch action.
All the thicknesses can be made quite small of an arch is used because the stresses will be principally compression. The
curve of the arch has to be generally a funicular form, that is, it should fit the thrust line of the applied loads. Shells are
not very efficient structures if the bending moments are high, as in the folded plate rigid frame.


   

    

          
 


You might also like