Air Compressor PDS 100S PDF

INSTRUCTIONAL MANUAL
AIR COMPRESSOR
PDS100S-6B4, PDS103S-6B4,
PDS185S-6B4
MMD Equipment Inc.
121 High Hill Road
Swedesboro, NJ 08085
Tel: (800) 433-1382
Fax: (856) 467-5235
www.mmdequipment.com
Table of Contents
1. Safety ....................................................................................................................................................... 1-1
1.1 Caution before Operation ................................................................................................................ 1-2
1.2 Caution during Operation ................................................................................................................ 1-6
1.3 Caution during Inspection and Maintenance ................................................................................... 1-8
1.4 Safety Warning Labels .................................................................................................................... 1-12
2. Operation ................................................................................................................................................. 2-1

2.1 Unit Appearance and Part Names ................................................................................................... 2-1
2.2 Internal Components and Part Names ............................................................................................ 2-2
2.3 Instrument Panel ............................................................................................................................. 2-3
2.4 Compressed Air Service Valve ....................................................................................................... 2-5
2.5 Door ................................................................................................................................................ 2-5
2.6 Check before Starting Unit .............................................................................................................. 2-5
2.7 Unit Operation ................................................................................................................................. 2-12
2.8 Stopping Procedures ....................................................................................................................... 2-15
3. Transportation and Towing the Unit ..................................................................................................... 3-1

3.1 Transportation ................................................................................................................................. 3-1
3.2 Towing the Unit ............................................................................................................................... 3-2
4. Installation ............................................................................................................................................... 4-1

4.1 Location and Installation ................................................................................................................. 4-1
5. Periodic Inspection/Maintenance .......................................................................................................... 5-1

5.1 Important Items as Periodic Inspection and Maintenance or after Maintenance ............................. 5-1
5.2 Daily Inspection and Operation Log ................................................................................................ 5-2
5.3 Periodic Inspection List ................................................................................................................... 5-3
5.4 Periodic Replacement of Parts ........................................................................................................ 5-5
5.5 Items and Places of Inspection ......................................................................................................... 5-6
5.6 Maintenance Items .......................................................................................................................... 5-7
6. Maintenance/Adjustment ....................................................................................................................... 6-1

6.1 Adjustment of Regulator .................................................................................................................. 6-1
6.2 Maintenance of Battery ................................................................................................................... 6-2
6.3 Troubleshooting .............................................................................................................................. 6-4
7. Storage of the Unit ................................................................................................................................. 7-1

7.1 Preparation for Long-term Storage ................................................................................................. 7-1
8. Specifications ......................................................................................................................................... 8-1

8.1 Compressor Specifications ............................................................................................................. 8-1
9. Wiring Diagram ....................................................................................................................................... 9-1
10. Piping Diagram ....................................................................................................................................... 10-1

1. Safety
This manual explains and illustrates general requirements for safety.
Read all safety requirements carefully and fully understand the contents before starting the machine.
For your better recognition, according to the degree of potential danger, safety messages are classified
into three hierarchical categories, namely, , , and with a caution
symbol attached to each message.
When one of these messages is shown, please take preventive measures and carry out SAFETY
OPERATION AND PROPER MAINTENANCE OF THE UNIT.
DANGER indicates an imminently hazardous situation which, if not avoided,

will result in death or serious injury. This signal word is to be limited to the
most extreme situations.
WARNING indicates a potentially hazardous situation which, if not avoided,

could result in death or serious injury.
CAUTION indicates a potentially hazardous situation which, if not avoided,

may result in minor or moderate injury. It may also be used to alert against
unsafe practices.
IMPORTANT indicates important caution messages for the performance or

durability of the unit.
Follow warnings mentioned in this manual. This manual does not describe all safety items. We,
therefore, advise you to pay special attention to all items (even though they may not be described
in the manual) for your safety.
1-1
1. Safety
1.1 Caution before Operation
Air pressurized construction method prohibited
Never use the unit directly or indirectly for the following

purposes:
Never use the unit for respirator equipment by which
compressed air is supplied for human consumption. The
compressed air contains carbon monoxide and other
contaminants. Such air may cause serious injury or death if
used by a person for respiration.
This compressor is not designed for air pressurized
construction methods and underwater diving jobs.
Never use compressed air for human consumption such as TR0201
pressurizing diving air tanks. Consumption of compressed air
can cause death while diving.
Ventilation
Exhaust gas from the engine is poisonous, and could cause

serious injury or death when inhaled.
Avoid using the machine in an insufficiently ventilated building
or tunnel.
PC002
Follow all safety instructions
Read each instruction plate which is displayed in the manual or

on the unit carefully, understand its content and follow the
directions.
Keep the Safety Warning labels clean. If they are damaged or
missing, apply new ones.
Do not modify the machine without prior approval. Safety of the
unit may be compromised, functions may be deteriorated, or
machine life may be shortened.
Never use the unit for the purpose of compression of gases
other than air, or as a vacuum pump. Serious accidents may TR0086
occur.
Maintain both physical and mental health
Do not operate the machine you are tired, intoxicated or under the influence of drugs. Operation under
these circumstances may cause unexpected injury or accident.
Maintain your physical and mental health and be cautious in handling the machine.
1-2
1. Safety
Safety outfit
When handling the machine, do not wear;

loose clothes
clothes with unbuttoned sleeves
hanging tie or scarf
accessories such as dangling jewelry
Such outfit could be caught in the machine or dragged in the
rotating portion of the machine which could cause a serious
injury.
TR0084
Transportation
When loading and unloading unit, be sure to use the lifting bail provided on the center of the unit top.
Never get under the unit which is suspended, it is very dangerous.
When unit is transferred or moved from a working site, be sure to place it on truck bed, and tie it down
firmly. Also be sure to put a set of chocks to fix its wheels firmly in position.
Never lift unit which is still in operation. It could cause critical damage to each component or lead to
serious accident.
Installation
The machine should be parked horizontally on a level place.

In case the machine has to be parked on a slope, place it
across grade so that the machine does not tend to roll
downhill.
Grade on a slope shall be within 15 degrees
Be sure to put one set of chocks1to the wheels.
A000054
Cautions of hose attachment and removal
Piping or the hose from this machine service valve should use
what can be borne enough for the discharge pressure of this
machine.
Please connect piping or a hose to this machine service valve
firmly before operation and during operation. If the connection
part is loosening, there is a possibility of piping or a hose
separating and getting seriously injured.
TR0088
Please remove after closing a service valve and extracting
pressure remained, in case piping or a hose is removed. If
TR0088
pressure remained should remain, a near thing blows away or
there is a possibility of a hose whipping, causing a
phenomenon and getting seriously injured.
In order to use it safely, please read the handling of the work
tools often used.
TR0303A
1-3
1. Safety
Handling battery
Keep flames away from battery.

Battery generates hydrogen gas and may explode.
Therefore, recharging should be done at a well-ventilated
place.
Do not allow sparks or flame near the battery.
Do not check the battery by short-circuiting the positive and
negative terminals.
D004
Never operate the machine nor charge the batteries with the
battery liquid level being kept lower than the "LOWER" level.
Continuing operation at this lower level will cause deterioration
of such parts as pole plates etc., and also it may cause
explosion as well as reduction of battery life. Add distilled water
so that the liquid level may reach the middle level between the
"UPPER" and "LOWER" level without any delay.
Do not charge a frozen battery. Otherwise it may explode. If
the battery is frozen, warm it up until the battery temperature W010
becomes 61F to 86F (16C to 30C).
Battery electrolyte is dilute sulfuric acid.
In case of mishandling, it could cause skin burning.
When you deal with a battery, please be sure to wear
protection implements, such as protection glasses and a glove.
When such battery electrolyte contacts your clothes or skin,
wash it away with large amount of water immediately.
If the battery electrolyte gets into your eyes, wash it away
immediately with plenty of water and seek medical attention.
Dispose of battery, observing local regulations.
TR0093
Check before starting the unit
Be sure to check the unit before operation.

When any abnormality is found, be sure to repair it before restarting the unit.
Be sure to make daily checks before operation. If the unit is operated without prior check and without
noticing any abnormality, operation could cause damage of components or may even cause fire.
1-4
1. Safety
Protection equipments
Please wear protection implements, such as a helmet,

protection glasses, earplugs, safety shoes, a glove, and a
protection-against-dust mask, according to the contents of
work for safety.
TR0085
Safety fittings
Have first-aid kits and fire-extinguishers near the unit ready for
emergency situations.
It is advisable to have a list of phone numbers of doctors,
ambulance and the fire department available in case of
emergency.
TR0096
Safety around the machine
Unnecessary equipment and tools, cables, hoods, covers which are a hindrance to the job, have to
be removed.
1-5
1. Safety
1.2 Caution during Operation
Do not replenish compressor oil during operation
Do not, under any circumstance, open the oil filler cap of

separator receiver tank while running or immediately after
stopping operation.
It is very dangerous and cause serious injury.
Relieve all pressure before performing any maintenance.
W010
Draining during operation prohibited
Do not, under any circumstance, open the items listed below

during operation:
Separator receiver tank drain valve
Coolant drain valve and plug
Engine oil drain plug
Oil cooler drain plug
PK0028
Beware of cooling fan
Never put your hand near the engine cooling fan during
operation.
W009
Hands off from rotating parts and belts
Keep hands off from the rotating portion or belts while running.
TR0304
1-6
1. Safety
Never direct the compressed air to people and foods
Never blow compressed air directly at people.

Scattered dust, or foreign objects in the compressed air may
cause serious injuries.
Blowing compressed air on food is prohibited.
TR0092
Do not remove radiator cap during operation
Do not, under any circumstance, open the radiator cap while

running or immediately after stopping operation. Otherwise
high temperature steam releases out and this could cause
scalding.
H990432
Do not touch hot parts
Never work near hot portions of the machine while it is running.

Such parts as engine, exhaust manifold, exhaust pipe, muffler,
radiator, oil cooler, compressor, piping, separator receiver tank,
and discharging pipe are especially hot, so never touch those
parts, because it could cause serious burns.
Compressor oil, coolant water, and engine oil are also very hot
and dangerous to touch.
Avoid checking or refilling them while the unit is running.
H990432
Operation with compressed air supply port opened is prohibited
Do not operate the machine with service valves and relief valve
open unless air hoses and/or pipes are connected.
When the machine has to be unavoidably temporarily operated
with its port open, be sure to mount a silencer to reduce noise
and wear protective materials such as earplugs to prevent
damage to hearing. For testing service only.
D003
1-7
1. Safety
Fire prevention
Do not, under any circumstance, bring lit cigarettes or matches

near oils as engine oil and compressor oil, etc.
They are extremely flammable and dangerous.
Refilling oils should be done in an outdoor well-ventilated
place.
Refuel after stopping the engine, and never leave the fuel
nearby the machine. Do not spill. Clean environmental spills.
D004
Such parts as muffler and exhaust pipe can be extremely hot.
Remove twigs, dried leaves, dried grass and waste paper, etc.
from the exhaust outlet of the muffler.
Keep a fire extinguisher available by the machine in case of a
fire.
H990433
1.3 Caution during Inspection and Maintenance
Hang a Now Checking and under Maintenance tag
Remove the starter key from the starter switch before starting
inspection, and hang up a Now Checking and under
Maintenance tag where it can be easily seen. The checker
must keep the key during checking and maintenance.
Remove the negative () side cable from the battery.
SY001
Refilling of compressor oil
When you refill the separator receiver tank with compressor oil,
stop the engine, and make sure that the pressure gauge
indicates 0 psi (0 bar) and there is no residual pressure in it,
and then gradually loosen the oil filler cap for refilling oil.
Note residual pressure in the separator receiver tank could
force both extremely hot compressed air and oil to jet out and
W010
you may be scalded or seriously injured.
1-8
1. Safety
Draining separator receiver tank
After stopping the engine, confirm that the pressure gauge

then open the drain valve gradually to drain the compressor oil.
Note residual pressure in the separator receiver tank could
force both extremely hot compressed air and oil to jet out and
you may be scalded or seriously injured.
H990432
Be careful of high-pressurized air blowout
After stopping the engine, make sure that pressure gauge

indicates 0 psi (0 bar). Even when the gauge shows 0 psi (0
bar), open a service valve and further do not fail to make sure
that there is no residual pressure in the air piping. Then begin
repair and maintenance.
Residual air under pressure can cause severe injury.
W010
Adjusting tension of fan belt
Be sure to stop the engine and remove the starter key

whenever the tension of the fan belt is to be adjusted.
If the machine is running, it might catch the operators hand
into the fan belts, and this could cause a serious injury.
TR0304
Hands off from cooling fan
Be sure to stop the engine and remove the starter key

whenever check or maintenance work is carried out near the
cooling fan.
If the cooling fan is rotating, it may catch the operator or part of
his body into the fan, and it could cause a serious injury.
W009
1-9
1. Safety
Cleaning by air-blow
When cleaning dust accumulated in such devices as the

air-filter, by blowing compressed air, wear safety glasses, etc.
to protect your eyes.
M003
Lighting apparatus
It is recommended to use a lamp with safety guard fitted in low

light conditions.
Any lamps without safety guard are not recommended since
they can be broken and they could ignite flammables such as
fuel, etc.
TR0206
Taking off the radiator cap
Be sure to stop the machine and allow time to cool. Then

loosen the radiator cap one notch. After the coolant water is
sufficiently cooled and the inner pressure is released, take the
cap off.
If this procedure is neglected, the inner pressure can blow off
the cap. Steam jetting out of the radiator could result in
scalding. Follow this procedure under all circumstances.
H990432
Opening coolant water drain valve cap
Be sure to stop the engine, and let the coolant water

sufficiently cool down before draining it.
If the drain valve is opened before the coolant water is cooled
enough, hot water could jet out, and it could cause scalding.
H990432
1-10
1. Safety
Refilling or draining of engine oil
After stopping the engine, wait for 10 to 20 minutes until the

engine oil cools off. Then check the level of the engine oil, or
refill or drain the oil.
Engine oil is very hot and highly pressurized during or just after
the operation. Hot oil could blow out of the tank and can cause
scalding.
H990432
Fire warning
Be sure to perform the periodical check of compressor oil and

oil separator.
Neglecting checks could cause overheat of the oil, resulting in
a fire.
H990433
Disposal of waste liquid, etc.
Waste liquid from the machine contains harmful material. Do not discharge it onto the ground or into
the river, lake or sea. Such material will contaminate the environment.
Be sure to use a container to hold the waste liquid from the machine.
Be sure to follow the designated regulations when disposing of oil, fuel, coolant (antifreeze), filter,
battery or other harmful materials.
1-11
1.Safety
1.4 Safety Warning Labels
Following labels are attached to the machine.
Keep them clean all the time. If they are damaged or peeled off, immediately place an order with
your nearest dealer for replacement, with the number indicated on the lower right corner of the
label. Adhere a new one to the original place.
5
1
4 5
6 6
7 8
3 2
10
11
A
5
A-View
A050230
1. Caution, exhaust gases 3. Lifting bail 5. Caution, high temp. 7. Caution, Fire 9. No fire 11. Caution, hose whipping
(39176 73300) (39176 69300) (39176 69500) (39176 69700) (39176 35600) (39176 73400)
2. Caution, radiator cap 4. Caution, cooling fan 6. Caution, fan belt 8. Caution, residual pressure 10. Caution, Do not inhale
(hot water) (39176 73500) (39176 73800) (39176 69800) (39176 73600)
(39176 69600)
1-12
2. Operation
2.1 Unit Appearance and Part Names
A030132
PDS185S-6B4
1. Exhaust outlet 5. Service valve

2. Lifting bail 6. Drawbar
3. Door 7. Instrument panel
4. Handle
2-1
2. Operation
2.4 Compressed Air Service Valve
2.4.1 Service Valve (20A)

Open Close
Open the valve by turning the handle clockwise, and close it
by turning the handle counterclockwise.
TR0642
2.5 Door
2.5.1 Open/Close the Door
Keep the door closed and locked while running the unit.
When the door has to be opened, be careful not to touch
portions that are rotating or very hot.
Careless touch may cause serious injury.
PK0028
Pull the handle forward to open the door.

Be sure to close the door tightly so that its latch is firmly caught.
2.6 Check before Starting Unit
Check before starting the unit
Be sure to check the unit before operation.

When any abnormality is found, be sure to repair it before restarting the unit.
Be sure to make daily checks before operation. If the unit is operated without prior check and without
noticing its abnormality, such operation could cause seizure of components or may even cause fire.
2-5
2. Operation
2.6.1 Check Items and Locations
3 2 4
PDS185S-6B4
1
6
PDS100S-6B4
PDS130S-6B4
5 7 8
A050233
1. Check fuel 6. Check compressor oil level

2. Check V-belt tension 7. Drain fuel tank
3. Check coolant level 8. Check engine oil level
4. Drain water sedimenter Check wiring of each part
5. Draining of separator receiver tank Check piping of each part
2-6
2. Operation
2.6.2 Check Engine Oil Level
Unit should be on level before checking oil level.
When you check oil level after you have once started operation, wait 10 to 20 minutes after
stopping engine, before checking the oil level.
(Procedure)
Pull out the engine oil dipstick, and wipe it with a clean When oil level is
cloth. within this zone, HIGH
Then, re-insert the dipstick fully and pull it out again. If it is normal.
the dipstick shows the oil level between HIGH and LOW, it
is normal.
When the oil level is below its LOW, add engine oil.
LOW
(See 5.6.1)
While checking oil level, check also for contamination. If the
oil is found dirty, contaminated or should it be changed A050232
according to the periodic inspection list, change the oil.
(See 5.6.1)
Never fill oil more than HIGH level.
2.6.3 Check Coolant Level
Be sure to stop the machine and allow time to cool. Then loosen
the radiator cap one notch. After the coolant water is sufficiently
cooled and the inner pressure is released, take the cap off.
the cap. Steam jetting out of the radiator could result in causing
H990432
Check the coolant level in the reserve tank. If it is lower

than the limit, open the cap and replenish the coolant.
(Level must be kept above LOW mark.)
If little coolant is left in the reserve tank, replenish the
radiator with cooling water. (See 5.6.15)
LOW
H000036
2-7
2. Operation
2.6.4 Check Compressor Oil Level
indicates psi (0 bar) and there is no residual pressure in it, and
then gradually loosen the oil filler cap for refilling oil.
Note residual pressure in the receiver tank could force both
extremely hot compressed air and oil to jet out and you may be
scalded or seriously injured.
W010
Place the machine on level ground when checking the oil

level.
Check the oil level of the compressor. Correct oil level is 1/2
between upper and lower limit of the gauge, when the unit 1/2
stops. If the gauge shows lower than the middle level,
replenish oil. (See 5.6.5)
H000037
2.6.5 Draining of Separator Receiver Tank
Draining of Separator receiver tank
After stopping the engine, confirm that the pressure gauge

then open the drain valve gradually to drain the compressor oil.
H990432
Gradually opening the drain valve 2fitted under the 1

separator receiver tank1as shown in the fig, drain the
condensate. 3
Be careful not to fully open the valve. Otherwise, much oil
may be lost.
2
After draining the oil completely, close the drain valve2
firmly.
4
Drain the condensate in container4, dispose of the waste
oil according to the designated regulations.
H000038
2-8
2. Operation
2.6.6 Check Fuel
Fire prevention
Do not, under any circumstance, smoke cigarettes or light

matches during fueling.
Fuel is extremely flammable and dangerous. It therefore, could
catch fire should it flame or other sources of ignition be brought
near fuel. Ensure that the engine is cool. Never fuel a hot
machine.
Refuel only after stopping the engine, and never leave an open
fuel can near the machine. Do not spill. It could cause a fire.
When it is spilt, wipe it up completely.
D004
Refilling fuel tank should be done in an outdoor well-ventilated
place.
Choose appropriate fuel

Be sure to use diesel fuel oil for diesel engine use.
(Using other oil will cause low power or damage to the engine.)
Check fuel level gauge before operation. Replenish enough fuel to prevent fuel shortage during
operation, if the level is low.
When refueling, fill a fuel tank up to the base of fuel filler port4. Never overfill fuel because it
may cause fuel leakage.
Be sure to fasten the fuel tank cap firmly after replenishment. If fuel is spilt, wipe it up
completely.
2.6.7 Drain Fuel Tank

Opening the drain valve2fitted under the fuel tank1, 4
drain the condensate from the tank.
1
When completely drained, firmly close the drain valve 2.
Drain the condensate in container3, dispose of condensate
according to the designated regulations.
2
3 H000039
2-9
2. Operation
2.6.9 Check V-Belt Tension
Too tight belt tension could damage shaft and shorten bearing life. Too loose belt tension may result in
damaging belt earlier and machine components due to overheat.
Follow the procedure below to adjust tension of fan belt and V-belt for alternator.
[PDS100S,130S-6B4]
(Procedure)
Adjust the tension by gradually loosening the fastening bolt 0.2 to 0.3in.[110bf(49N)]
of the alternator.
Visually check if there are any cracks or tears in the belt.
Loosen the fastening bolt of the alternator until the play of
the belt reaches 0.2 to 0.3 in. (6.0 to 8.0 mm) when pushed
by fingers, and adjust it.
Be careful not to leave any grease or LLC * on a belt while
changing it. If any such material is left, wipe it off
completely.
* Long life coolant H000041E-2
[PDS185S-6B4]
(Procedure)
Adjust the tension by gradually loosening the fastening bolt 0.32 to 0.45in.[22lbf(98.1N)]
of the alternator.
Visually check if there are any cracks or tears in the belt.
Loosen the fastening bolt of the alternator until the play of
the belt reaches 0.32 to 0.45 in. (8.0 to 12.0 mm) when
pushed by fingers, and adjust it.
Be careful not to leave any grease or LLC * on a belt while
changing it. If any such material is left, wipe it off
completely.
* Long life coolant H000041E-2
2-11
2. Operation
2.6.10 Check Wiring of Each Part
Check each wiring for any loose connection, damage to insulating sheathed portion, disconnection,
and short-circuit.
2.6.11 Check Piping of Each Part

Check each piping for any loose connection and also check each hose and pipe for any tear and leaks.
2.7 Unit Operation
Operation with compressed air supply port opened is prohibited
Do not operate the machine with service valves and relief valve
open unless air hoses and/or pipes are connected.
High-pressurized air blows out and its air pressure could cause
injury to the people nearby.
When the machine has to be unavoidably temporarily operated
with its port open, be sure to mount a silencer to reduce noise
and wear protective materials such as earplugs to prevent
damage to hearing. D003
Quick Glow System

Since this equipment is provided with a quick glow system (quick preheating device), you do not
have to turn the starter switch counterclockwise from STOP position.
Turn the starter switch to the RUN position, and the preheating will be completed in several
seconds and the preheating lamp will go out. Then, turn the Starter Switch to the Start position
to start up the engine.
When the engine is already warm, the preheating operation is automatically omitted. Even
though the preheating lamp lights up momentarily, ignore the lamp status, and start up the
engine.
WARNING Because of the quick glow system, never use starting fluids to start engine.
2-12
2. Operation
2.7.2 Operating Procedures when Engine Fails to Start up on First Attempt
When the engine fails to start up even after performing the startup procedures to , do not
keep the starter running, but set the starter switch back to STOP and wait about 30 seconds.
Then, repeat the startup procedure once again.
If the repeated procedure does not allow the engine to run, the following causes are suspected.
Check the following:
No fuel
Clogging of fuel filter
Clogging of filter inside the fuel air bleeding electromagnetic pump
Discharge of battery (Low cranking speed)
2.7.3 EFPA (Electrical Fuel Primer and Air Bleed)

If the unit runs out of fuel, the electromagnetic pump attached to the unit will automatically
bleed air out of the fuel system. (After draining sediment from water sedimenter or changing
fuel filter with a new one, bleed the air in the same procedure as below.)
(Procedure)
Replenish fuel.
Turn the starter switch to its RUN position. The electromagnetic pump starts pumping and
automatically bleed air caught in the fuel pipes.
Air-bleeding will be completed within 40 to 50 seconds.
Start the machine following the starting procedures mentioned in 2.7.1. If starting fails one time,
repeat the abovementioned procedures.
After finishing the air bleeding operation, never leave the starter switch placed on Run position
because the battery is discharging.
2.7.4 Operation under Cold Weather Conditions
When it is difficult to start engine in cold weather, take the

following measures.
Close
(Procedure) Open
Close all the service valves and fully open the relief valve
1provided at the front of the separator receiver tank.
When engine starts after performing the startup procedure,
gradually close the relief valve, watching the rise of engine
revolutions. Then after closing the valve fully, perform
warming-up operation in this state. 1
PDS130S-6B4
A030143
PDS185S-6B4
Operation under Cold Weather Conditions below 23F (-5C)

Use SAE10W-30 (CD class) for the engine oil.
Use LLC (antifreeze). Use correct amount to provide freeze protection, according to the ambient
temperature.
Battery should always be kept fully charged.
2-14
3. Transportation and Towing the Unit
3.1 Transportation
Transportation
When loading and unloading unit, be sure to use the lifting bail provided on the center of the unit top.
Never get under the unit which is lifted up, because it is very dangerous.
When unit is transferred or moved from working site, be sure to place it on truck bed, and fasten it by
ropes at the front eye and rear stand. Also be sure to put a set of chocks to fix its wheels firmly on the
truck bed.
Never lift unit which is still in operation, or it could cause critical damage to each component or lead to
serious accident.
When lifting unit up, make sure that all the fixing bolts on the bonnet are surely tightened because it is
feared that the unit may fall.
If towing unit : Make sure machine is towed level.
Check tire pressure and tire condition before towing.
Attach safety chains and use correct tow hitch.
Check operation of lights and brakes before towing.
Check wheel lug nuts for proper torque.
Lifting up
Before lifting the unit up, make sure to check the lifting bail
for any crack and loosened bolts.
Connect the hook1of the crane or shackle with lifting bail
2eye fitted at the top center of the unit, and make sure
that there is no person standing around the unit. Then
perform hoisting operation.
Use an auxiliary rope3and communicate with the other
personnel using signs and signals while lifting operation, so
that no swinging motion or twisting happens to the lifted
unit. A000053
Select a truck or a crane with capacity sufficient for weight
and size of the unit by referring to the values shown in
Chapter 8 Specifications of the manual.
Lowering the unit from the truck bed pulling down

Lower the unit down onto a level place which can sustain the weight of the unit.
After placing the unit down, put chocks to lock the wheels before unfastening the cranes shackles.
3-1
3. Transportation and Towing the Unit
3.2 Towing the Unit
Before towing the unit, check the following points and be sure to repair failures, if any:
Air-pressure in the tires.
Loose wheel bolts or nuts.
Abnormal wear or damage to the tires.
Damage of drawbar.
Be sure to use a vehicle with enough capacity to tow the unit in operating weight.
Do not tow the unit without unfastening tool, equipment, and hoses.
Keep hands and fingers clear during hook-up or unhooking drawbar.
If you do not follow the above instructions, it could cause serious injury or big damage.
3-2
4. Installation
4.1 Location and Installation
Ventilation
Exhaust gas from the engine is poisonous, and could cause

death when inhaled.
Avoid using the machine in an insufficiently ventilated building or
tunnel.
Do not position the exhaust gas outlet in direction of a person or
a house.
PC002
The machine has to be parked horizontally on a level place.

In case the machine has to be parked on a slope, place it across
grade so that the machine does not tend to roll downhill.
Grade on a slope shall be within 15 degrees
Be sure to put one set of chocks1to the wheels.
A000054
The machine should be operated in following conditions:

Ambient temperature 5F to 104F (-15C to +40C)
Humidity Less than 90%
Altitude Lower than 1,500 m above sea level
Install the machine in a place with good ventilation, lower temperature and with surroundings as
dry as possible.
If more than two machines are placed parallel in operation, keep enough distance so that exhaust
air from one machine does not affect the other one.
Also, a machine has to be installed in the environment where fresh air is always available.
Keep enough space around the unit for inspection and maintenance access.
4-1
5. Periodic Inspection/Maintenance
5.1 Important Items at Periodic Inspection and Maintenance or after
Maintenance
The manual shows proper interval for periodic inspection and maintenance under normally
operating conditions. Inspection and maintenance should be performed more often under
extremely harsh conditions.
Hang a Now Checking and under Maintenance tag
Remove the starter key from the starter switch before starting
inspection, and hang up a Now Checking and under
Maintenance tag where it can be easily seen. The checker must
keep the key during checking and maintenance.
If the above procedure is neglected, and another person starts
operating the machine during check or maintenance, it could
cause serious injury.
Use tools appropriate for the inspection and maintenance. Any
makeshift or improper tools could cause unexpectedly injury by
SY001
their slippage.
For protecting oil separator from fire accident
Be sure to perform oil change basically according to the

specified interval. But if such oil is found much more
contaminated before the interval, change the oil even before the
specified period comes. In doing so, replace the oil completely
2
and use our recommended oil.
Be sure to perform following periodic inspection and
maintenance:
1
1. Check and change compressor oil
2. Change oil separator
Never mix the oil of different brands, or the mixed oil may
deteriorate the oil quality. H000046
5-1
Precautions for check and maintenance
Be sure to use recommended fuel, oil, grease, and antifreeze.

Do not disassemble or adjust engine, compressor or part(s) for which inspection or maintenance is not
referred to in this manual.
Use genuine parts for replacement.
Any breakdown, caused by using unapproved parts or by wrong handling, will be out of the scope of
WARRANTY.
Keep the electrical components away from water or steam.
Waste from machines contains harmful material. Do not dispose of such harmful fluids to the ground,
rivers, lakes or ponds, and sea. It contaminates the environment.
When draining waste fluid from machines, use leakproof containers to hold such fluids from machine.
Be sure to follow the designated regulations when disposing of oil, fuel, coolant, filters, battery and other
harmful things.
5.2 Daily Inspection and Operation Log

Be sure to carry out daily inspection every morning before operation. See Chapter 2 Operation of
the manual for the details of inspection.
Pay attention to and carefully observe the following points during daily operation or inspection
and maintenance work. If any trouble or abnormality is found, immediately investigate its cause
and make repairs. If the cause is unknown or not traceable, or if the trouble involves a part or
component not described in the manual, ask your nearest dealer for information.
(a)Controls and instruments function properly.

(b)Quantity and any leak of water, fuel, and oil or any
contamination should be checked.
(c)Appearance, abnormal noise or excessive heat should be
checked.
(d)Loose bolt or nut should be checked.
(e)Any damage, wear or shortage of machine components and
parts should be checked.
(f)Performance of each part or component should be proper.
TR0049
Keep the operation log to record constant inspection of each component, so that trouble of the unit
can be easily discovered and preventive measures can be taken.
It is very useful to record information such as discharge pressure, oil level, as well as running hour,
maintenance items and replenishment of lubricant on a daily maintenance log.
5-2
5.3 Periodic Inspection List
(Unit:Hour)
Every Every Every Every Every Every Page
Maintenance Daily 250 300 500 1,000 2,000 3,000
Check compressor oil level. 2-8
Drain of separator receiver tank. 2-8
Check looseness in pipe connecting part, and wear
and tear of pipe. 2-12
Check oil, water, fuel and air leak. 2-15
Check performance of gauge and indication lamps. 2-15
Change compressor oil. 1 5-9
Change compressor oil filter. 1 5-10
Clean strainer in the scavenging orifice. 5-10
Compressor

Clean and change air filter element. 5-11
(Clean) (Change)
Clean outside of oil cooler. 5-13

Change speed regulator diaphragm. 5-12
Change oil separator. 5-15
Change nylon tubes. 5-15
Change unloader of o-ring. 5-16
Change spacer of unloader. 2
Change pressure regulator. 5-16
Check rubber hoses. 5-16
Check o-ring and needle valve of auto-relief valve. 5-16
Such items marked shall be carried out by customers.

For the following items or clauses marked , contact us directly or our distributors because they
require expert technical knowledge on them.
The following table shows the inspection and maintenance intervals under normal operation conditions.
In case the unit is operated under harsh environmental conditions and operation conditions, the
intervals should be shortened.
The items or parts marked 1 show that they should be replaced primarily.
The items or parts marked should be replaced every two years even if they are not in disorder within
their periodical maintenance interval because their materials will change or become degraded as time
passes.
Also for the same reason, the parts marked should be replaced every three years.
Regarding the item marked 2check the function of the unloader. In case the unloader malfunctions,
change O-ring or bushing of unloader. This is because either of both parts may be worn out.
5-3
Refer to engine operation manual for inspection and maintenance of an engine.

(Unit:Hour)
Every Every Every Every Every Every Every Page
Maintenance Daily 50 250 500 1,000 2,000 3,000 8,000
Drain fuel tank
(Including sedimenter). 2-9
Check fuel level 2-9
Check engine oil level. 2-7
Check coolant level. 2-7
Check looseness in pipe connectors, terminals and
tear in wiring. 2-12
Check V-belt tension. 2-11
Change engine oil. 5-7
Change engine oil filter. 5-8
Check battery electrolyte. 5-8
Engine
Change filter for air bleeding electromagnetic 5-12

pump.(PDS185S only) (Change)
Clean and change air-filter element. 5-11

(Clean) (Change)
Change fuel filter. 5-11

Change sedimenter element and O-ring.
(PDS100S,130S only) 5-12
Change coolant. 5-14
Clean inside of radiator. 5-13
Clean outside of radiator. 5-13
Change rubber hose. 5-15
Clean inside of fuel tank. 5-15
Change radiator hoses. 5-16
The items or parts marked show that they should be replaced primarily.
The items or parts marked should be replaced every two years even if they are not in disorder within
their periodical maintenance interval because their materials will change or become degraded as time
passes.
Also for the same reason, the parts marked should be replaced every three years.
5-4
5.4 Periodic Replacement of Parts
5.4.1 Filters
Part Name Part Number Quantity
PDS100S-6B4 SHIBAURA 140517020 1
Engine oil filter PDS130S-6B4 SHIBAURA 140517020 1
PDS185S-6B4 NISSAN 15208 43G00 1
Compressor oil filter 37438 05201 1
PDS100S-6B4 32143 11700 1
Air filter element PDS130S-6B4 32143 11800 1
PDS185S-6B4 32143 12700 1
Element4 SHIBAURA 360720060 1
PDS100S-6B4
O-ring5 SHIBAURA 052100440 1
Fuel filter Element4 SHIBAURA 360720060 1
PDS130S-6B4
Element PDS185S-6B4 NISSAN 16403 J5500 1
PDS100S-6B4
Sedimenter
PDS130S-6B4
Separator 34220 12801 1
Oil separator
O-ring 03402 15140 1
Filter for electromagnetic pump PDS185S-6B4 43540 05600 1
5.4.2 Diaphragms & O-Rings

Part Name Part Number Quantity
Diaphragm of speed regulator 36437 01500 1
Pressure regulator 36400 19000 1
O-ring1 03402 25021 1
O-ring2 03402 25008 1
Auto-relief valve
O-ring3 21221 02100 1
Needle valve4 36429 00800 1
O-ring of unloader 21441 03000 1
5-5
5.5 Items and Places of Inspection
1 2 3 4 5 6 7 8 9,10,11
12
13
14
15
16 17 18
A030139
PDS185S-6B4
1. Change pressure regulator 13. Clean strainer in the scavenging orifice

2. Change O-ring of unloader 14. Check O-ring and needle valve in the
3. Change air filter element auto- relief valve
4. Change diaphragms of speed regulator 15. Change compressor oil
5. Change engine oil filter 16. Check battery
6. Change engine oil 17. Change compressor oil filter
7. Change radiator hoses 18. Clean inside the fuel tank
8. Change fuel filter Change nylon tubes
9. Clean outside of the radiator and oil cooler Change rubber hoses and pipes
10. Clean inside the radiator
11. Change coolant
12. Change oil separator
5-6
5.6.5 Change Compressor Oil
At 300 hours for the first change and every 500 hours thereafter
indicates 0 psi (0 bar) and there is no residual pressure in it, and
then gradually loosen the oil filler cap for refilling oil.
W010
Do not mix compressor oil

Be sure to use recommended oil listed below.
Viscosity of the oil varies depending on the temperature and other environmental conditions.
Select one from the recommended oil listed below.
Maker and Brand of Recommended Oil
Maker Brand
HULS ANDEROL 3032
MOBIL RARUS SHC 1024
TEXACO SYN-STAR DE32
Even continuous oil replenishment cannot improve its deteriorated condition. Be sure to change the oil
completely at every scheduled interval.
Do not mix it with other brand oil, or it will cause poor performance and shorten the life of the
compressor oil. (But fresh compressor oil could accept a mixture of small amount of different brands.)
Running the unit with old and deteriorated compressor oil will cause damage to bearings, or serious
accident like ignition in a separator receiver tank. Be sure to change the oil completely at every
scheduled interval.
Follow the designated regulations to dispose of compressor oil.
5-9
5.6.13 Clean outside of Radiator and Oil Cooler
Every 1,000 hours
When the fin tubes1of a radiator and an oil cooler are
clogged with dust or other foreign materials, the heat

exchange efficiency drops and this will raise coolant
temperature and discharge air temperature. These tubes and
fins should be cleaned depending on the state of clogged fin
tubes 1even before 1,000 hours maintenance schedule.
Do not use a high pressure washer to protect fin tubes from
being damaged.
1 H000054
5.6.14 Clean inside of Radiator

Every 1,000 hours
When the inside of a radiator and water conduits of an engine are dirty with scale and rust, its
cooling efficiency will be deteriorated. Clean the interiors of such components periodically.
Ask your nearest dealer for such inner cleaning.
5-13
5.6.15 Change Coolant
Every 1,000 hours or every 2 years
Be sure to stop the machine and allow time to cool. Then loosen
the radiator cap one notch. After the coolant water is sufficiently
cooled and the inner pressure is released, take the cap off.
the cap. Steam jetting out of the radiator could result in causing
H990432
How to handle LLC (Antifreeze)
LLC (Antifreeze) is a toxic material.

When a person has injested LLC (Antifreeze) by accident, seek medical attention immediately.
When a person gets LLC (Antifreeze) in his eyes, wash the eyes with clean running water and
make him see a doctor immediately.
When LLC (Antifreeze) is stored, put it in a container with an indication saying LLC
(Antifreeze) inside and seal it up, then keep it in a place away from children.
Beware of flames.
Quality of coolant and antifreeze

Use soft water of good quality such as tap water for coolant.
When water with dirt, sand, and/or dust contained, or hard water such as well water (ground water) is
used, this will cause deposits inside radiator or on cylinder head, and will cause engine overheat due to
poor flow of coolant.
When replacing coolant, be sure to install a coolant filter and add coolant.
When the unit is used in a cold region and possible freezing is expected, it is recommended to use LLC
(Antifreeze) for the coolant.
Adjust mixing ratio of LLC (Antifreeze) with water according to Reference of LLC (Antifreeze)
the temperature. mixing ratio
Use LLC (Antifreeze) within the range of its mixing ratio Temperature Mixing ratio
between 35 and 60%. 4F (20C) 35%
If LLC (Antifreeze) in the water exceeds more than 60%, it
40F (40C) 55%
may decrease its antifreezing effect.
Follow the designated regulations to dispose of LLC
(Antifreeze).
5-14
6. Maintenance/Adjustment
6.1 Adjustment of Regulator
Do not run the compressor with compressed air supply port open
When adjusting the regulator, be sure to mount a silencer at

the discharge opening to eliminate sound. Wear protective
materials such as earplugs to prevent hardness of hearing.
D003
Regulator is pre-adjusted at delivery from the plant. Never turn the bolt and rod. Otherwise it leads
to maladjustment.
In accordance with the following adjustment procedures, make sure to set engine revolutions to
make governor lever contact high-speed stopper at full load. If the pressure in separator receiver
tank with engine speed set lower than rated speed drops lower than 44 psi (3 bar) discharge air
temperature could rise so much to cause a serious trouble.
Be sure to follow the procedure below when the component is required to be re-adjusted (such as
when the unit has been disassembled).
Ask your nearest dealer if you have any questions.
(Procedure)
Stop the compressor and adjust the length of the rod 2 3 4 1
3 which is connected to the speed regulator2until
its engine governor lever1is pulled fully to its
high-speed side. (By shortening length of L, the
regulator increases high-speed.) If the engine governor
lever1does not reach the end of stopper4at its High Low
PDS100S-6B4 Speed Speed
high-speed side, sufficient speed of the engine, at its
full-load condition, cannnot be obtained. There is no PDS130S-6B4 A040309
need for unload revolution readjusttment.
Adjust the pressure regulator 5 by turning its 4
pressure adjustment screw6, so that the speed 2 3
regulator2starts its actuation and decreases the
1
engine speed when the pressure exceeds 100 psi (6.9
bar). (Pressure increases by tightening the screw, and
decreases by loosening the screw.)
L
High Low
Speed Speed
PDS185S-6B4 A000074
H000059
6-1
6.2 Maintenance of Battery
Handling battery
Keep flames away from battery.

Battery generates hydrogen gas and may explode.
Therefore, recharging should be done at a well-ventilated
place.
Do not allow sparks or flame near the battery.
Do not check the battery by short-circuiting the positive and
negative terminals.
D004
Never operate the machine nor charge the batteries with the
battery liquid level being kept lower than the "LOWER" level.
Continuing operation at this lower level will cause deterioration
of such parts as pole plates etc., and also it may cause
explosion as well as reduction of battery life. Add distilled water
so that the liquid level may reach the middle level between the
"UPPER" and "LOWER" level without any delay.
Do not charge a frozen battery. Otherwise it may explode. If the
battery is frozen, warm it up until the battery temperature W010
becomes 61F to 86F (16C to 30C).
Battery electrolyte is dilute sulfuric acid.
In case of mishandling, it could cause skin burning.
When you deal with a battery, please be sure to wear protection
implements, such as protection glasses and a glove.
When such battery electrolyte contacts your clothes or skin,
wash it away with large amount of water immediately.
If the battery electrolyte gets into your eyes, wash it away
immediately with plenty of water and seek medical attention.
Dispose of battery, observing local regulations.
TR0093
Do not connect the cables backwards
If a booster cable has to be used or when cables are connected at battery replacement, be careful not
to connect (+) and () terminals backwards. A wrong-connection will cause spark and damage
components. Explosion may result.
6-2
Symptom Cause Countermeasures
Engine oil (1) Engine oil shortage. Replenish oil
pressure lamp goes (2) Engine oil filter clogging. Change
on. (3) Malfunction of engine oil pump Change
(4) Faulty oil pressure switch. Change
(5) Loosened or disconnected wiring or Check/Fasten
connector.
Coolant (1) Radiator clogging. Clean
temperature lamp (2) Faulty thermostat. Change
goes on. (3) Faulty coolant temperature switch. Change
(4) Shortage of coolant. Replenish
(5) Slippage of fan belt. Adjust tension
(6) Looseness, disconnection of wiring or Check/Fasten
connectors.
Discharge air (1) Oil cooler clogging. Clean
temperature lamp (2) Oil filter clogging. Change
goes on. (3) Faulty discharged air temperature Check/Change
switch.
(4) Looseness, disconnection of wiring or Check/Fasten
connectors.
(5) Slippage of fan belt. Adjust tension
(6) Shortage of compressor oil. Replenish oil
(7) Malfunction of by-pass valve.
Fuel residual level (1) Fuel runs short. Add fuel oil
lamp goes on. (2) Malfunction of sending unit for fuel oil Inspect/replace
level drop.
(3) Loosened and disconnected wiring Inspect/retighten
connection and connectors.
Contact your nearest dealer if you find it difficult to repair by yourselves.
Refer to the engine operation manual for trouble concerning the engine.
6-5
6.3 Troubleshooting
Should any trouble occur during operation, do not leave it. Investigate the cause and take
appropriate measures.
Read the manual carefully and fully understand what to do in case of trouble.
The better you understand the construction and function of the unit, the faster you can find a
problem and solution.
This chapter describes the state, cause and countermeasures of important troubles in detail:
Symptom Cause Countermeasures

Low starter (1) Battery malfunction. Check battery
revolution speed. Charge, change
Starter rotates but (1) Fuel filter clogging. Disassemble, clean, and
engine does not change
start. (2) Malfunction of fuel cut solenoid or Check fuse
motor stopper. Change solenoid or motor
stopper
Check connector
(3) No fuel. Replenish fuel
Discharge air (1) Pressure regulator insufficient adjustment. Re-adjust (Fasten)
pressure does not (2) Starting unloader valve is left at its Place it at RUN position
reach 100 psi (6.9 start position.
bar).
Engine does not (1) Improper length in speed regulator rod. Re-adjust
reach its (2) Unloader orifice clogging. Disassemble/Clean
maximum speed. (3) Faulty speed regulator. Disassemble/Check
(4) Engine trouble. Call your nearest dealer
(5) Fuel filter clogging. Disassemble/Change
Revolution drops (1) Pressure regulator insufficient Re-adjust (Fasten)
before discharge adjustment.
air pressure (2) Trouble of pressure regulator. Change
reaches 100 psi (3) Unloader orifice clogging. Disassemble/Check
(6.9 bar).
Engine does not (1) Improper length in speed regulator rod. Re-adjust
reach minimum (2) Faulty speed regulator. Disassemble/Check
revolution at
unload.
Safety valve (1) Pressure regulator insufficient Re-adjust (loosen)
relieves at unload. adjustment.
(2) Speed regulator diaphragm damaged. Change
(3) Unloader valve damaged and seat Change
malfunction.
(4) Faulty safety valve. Change
(5) Improper length of speed regulator rod. Re-adjust (elongate)
Oil mixes in Air. (1) Scavenging orifice strainer clogging. Disassemble/Clean
(Poor oil (2) Excessive oil in tank. Drain to its proper level
separation) (3) Low discharge pressure. Disassemble unloader/Check
(4) Oil separator deteriorated. Disassemble/Change
Insufficient free air (1) Air filter element clogging. Clean element or change
delivery. (2) Unloader valve cannot fully open. Call your nearest dealer
(3) Engine does not reach rated speed. See 6.1.
6-4
7. Storage of the Unit
7.1 Preparation for Long-term Storage
When the unit is to be kept unused in storage for a long time, be sure to follow the preparations
below and put the unit in a dry and less dusty place.
Put the unit in a temporary cabin if it is stored outside. Avoid leaving the unit outside with a sheet
cover directly on the paint for a long time, or this will cause rust to the unit.
Perform the following treatments at least once every three months.
(Procedure)
Drain existing lubricant from the engine oil pan. Pour new lubricant in the engine to clean its
inside. After running it for a while, drain it again.
Spread lubricant on moving parts like speed regulator and rod end, beforehand.
Completely charge the battery and disconnect grounding wires. Remove the battery from the unit,
if possible, and store it in a dry place. (Charge the battery at least once every month.)
Drain coolant and fuel from the unit.
Seal the engine, air-intake port and other openings like the muffler with a vinyl sheet, packing
tape, etc., to prevent moisture and dust from getting in the unit.
Be sure to repair any trouble and maintain the unit so that it will be ready for the next
operation.
7-1
8. Specifications
8.1 Compressor Specifications
PDS100S-6B4
in. 106 Single-stage oil cooled,
Overall length Type
(mm) (2,680) screw type compressor
Overall length in. 62 cfm 100
Free air delivery
(bonnet only) (mm) (1,580) (m3/min) (2.85)
in. 57 psi 100
Overall width Working pressure
Compressor
(mm) (1,450) (bar) (6.9)
in. 55 Forced lubrication by
Overall height Lubricating system
(mm) (1,395) compressed pressure
lb 1,742 Direct driving with
Net dry mass Driving system
(kg) (790) gear coupling
lb 1,907 Receiver tank cu in. 1,833
General Specifications
Operating mass
(kg) (865) capacity (m3) (0.030)
gal. 18.5 Lubricating oil gal. 3.7
Fuel tank capacity
(L) (70) capacity (L) (14)
Model SHIBAURA S773L-C
Water-cooled 4-cycle
Type
pre-chamber type
Number of cylinders, in. 3-3.03in.3.19in.
bore stroke (mm) 3-77mm81mm
cu in. 69
Total displacement
Engine
(L) (1.131)
hp/rpm 27.1/3,425
Rated output
(kW/min-1) (20.2/3,425)
Lubricating oil gal. 1.3
capacity (L) (4.9)
Coolant capacity gal. 1.2
(including radiator) (L) (4.5)
Battery 80D26RMF
Outline drawing Unit:in.(mm)
A050236
8-1
8. Specifications
PDS130S-6B4
Overall length Type
Overall length in. 62 cfm 130
Free air delivery
(bonnet only) (mm) (1,580) (m3/min) (3.7)
in. 57 psi 100
Compressor
(mm) (1,450) (bar) (6.9)
lb 1,940 Direct driving with
(kg) (880) gear coupling
Operating mass
(kg) (960) capacity (m3) (0.030)
gal. 18.5 Lubricating oil gal. 3.7
Fuel tank capacity
(L) (70) capacity (L) (14)
Model SHIBAURA N843L-C
Type
direct injection
cu in. 101
Total displacement
Engine
(L) (1.662)
hp/rpm 37.5/3,000
Rated output
(kW/min-1) (28.0/3,000)
capacity (L) (6)
Battery 80D26RMF
A040290
8-2
8. Specifications
PDS185S-6B4
shows 49HP specifications
Overall length Type
Overall length in. 73 cfm 177 166
Free air delivery
(bonnet only) (mm) (1,850) (m3/min) (5.0) (4.7)
in. 57 psi 100
Compressor
(mm) (1,450) (bar) (6.9)
lb 2,249 Direct driving with gear
(kg) (1,020) coupling
Operating mass
(kg) (1,125) capacity (m3) (0.030)
gal. 24 Lubricating oil gal. 4.2
Fuel tank capacity
(L) (90) capacity (L) (16)
Model NISSAN TD27
Type
pre-chamber type
cu in. 162.5
Total displacement
Engine
(L) (2.663)
hp/rpm 51.6/2,600 45.7/2,400
Rated output
(kW/min ) (38.0/2,600) (34.1/2,400)
-1

capacity (L) (12)
Battery 80D26RMF
A000085
8-3
9. Wiring Diagram
PDS100S-6B4
PDS130S-6B4
A050044E
9-1
9. Wiring Diagram
PDS185S-6B4
A030125
9-2
10. Piping Diagram
PDS100S-6B4
A050211
10-1
10. Piping Diagram
PDS130S-6B4
A050222E-1
10-2
10. Piping Diagram
PDS185S-6B4
A050228
10-3
., .
12TH FLOOR SHINJUKU SAN-EI BLDG,

22-2 NISHI-SHINJUKU 1-CHOME,SHINJUKU-KU
TOKYO 160-0023 JAPAN
TEL:TOKYO 813(3348)7281
FAX:TOKYO 813(3348)7289
URL:http//www.airman.co.jp
39600 64220
PRINTED IN JAPAN 2005.12

Air Compressor PDS 100S PDF

Uploaded by

Copyright:

Available Formats

Air Compressor PDS 100S PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Air Compressor PDS 100S PDF

Uploaded by

Copyright:

Available Formats

INSTRUCTIONAL MANUAL

2. Operation ................................................................................................................................................. 2-1

3. Transportation and Towing the Unit ..................................................................................................... 3-1

4. Installation ............................................................................................................................................... 4-1

5. Periodic Inspection/Maintenance .......................................................................................................... 5-1

6. Maintenance/Adjustment ....................................................................................................................... 6-1

7. Storage of the Unit ................................................................................................................................. 7-1

8. Specifications ......................................................................................................................................... 8-1

9. Wiring Diagram ....................................................................................................................................... 9-1

10. Piping Diagram ....................................................................................................................................... 10-1

DANGER indicates an imminently hazardous situation which, if not avoided,

WARNING indicates a potentially hazardous situation which, if not avoided,

CAUTION indicates a potentially hazardous situation which, if not avoided,

IMPORTANT indicates important caution messages for the performance or

Air pressurized construction method prohibited

Never use the unit directly or indirectly for the following

Exhaust gas from the engine is poisonous, and could cause

Follow all safety instructions

Read each instruction plate which is displayed in the manual or

Maintain both physical and mental health

When handling the machine, do not wear;

The machine should be parked horizontally on a level place.

Cautions of hose attachment and removal

Keep flames away from battery.

Check before starting the unit

Be sure to check the unit before operation.

Please wear protection implements, such as a helmet,

Safety around the machine

Do not replenish compressor oil during operation

Do not, under any circumstance, open the oil filler cap of

Draining during operation prohibited

Do not, under any circumstance, open the items listed below

Beware of cooling fan

Hands off from rotating parts and belts

Never direct the compressed air to people and foods

Never blow compressed air directly at people.

Do not remove radiator cap during operation

Do not, under any circumstance, open the radiator cap while

Do not touch hot parts

Never work near hot portions of the machine while it is running.

Operation with compressed air supply port opened is prohibited

Do not, under any circumstance, bring lit cigarettes or matches

1.3 Caution during Inspection and Maintenance

Hang a Now Checking and under Maintenance tag

Refilling of compressor oil

Draining separator receiver tank

After stopping the engine, confirm that the pressure gauge

Be careful of high-pressurized air blowout

After stopping the engine, make sure that pressure gauge

Adjusting tension of fan belt

Be sure to stop the engine and remove the starter key

Hands off from cooling fan

Be sure to stop the engine and remove the starter key

When cleaning dust accumulated in such devices as the

It is recommended to use a lamp with safety guard fitted in low

Taking off the radiator cap

Be sure to stop the machine and allow time to cool. Then

Opening coolant water drain valve cap

Be sure to stop the engine, and let the coolant water