Verification Manual Russian Code SP 16.13330.2011

Autodesk
Robot Structural Analysis

Professional
VERIFICATION MANUAL
FOR STEEL MEMBERS DESIGN
March 2014

2014Autodesk,Inc.AllRightsReserved.ExceptasotherwisepermittedbyAutodesk,Inc.,this
publication,orpartsthereof,maynotbereproducedinanyform,byanymethod,foranypurpose.
Certainmaterialsincludedinthispublicationarereprintedwiththepermissionofthecopyright
holder.

Disclaimer
THISPUBLICATIONANDTHEINFORMATIONCONTAINEDHEREINISMADEAVAILABLE
BYAUTODESK,INC.ASIS.AUTODESK,INC.DISCLAIMSALLWARRANTIES,EITHER
EXPRESSORIMPLIED,INCLUDINGBUTNOTLIMITEDTOANYIMPLIEDWARRANTIES
OFMERCHANTABILITYORFITNESSFORAPARTICULARPURPOSEREGARDINGTHESE
MATERIALS.

Trademarks
ThefollowingareregisteredtrademarksofAutodesk,Inc.,intheUSAand/orothercountries:
AutodeskRobotStructuralAnalysisProfessional,AutodeskConcreteBuildingStructures,SpreadsheetCalculator,
ATC,AutoCAD,Autodesk,AutodeskInventor,Autodesk(logo),Buzzsaw,
DesignWebFormat,DWF,ViewCube,SteeringWheels,andAutodeskRevit.
Allotherbrandnames,productnamesortrademarksbelongtotheirrespectiveholders.

Third Party Software Program Credits
ACISCopyright19892001SpatialCorp.PortionsCopyright2002Autodesk,Inc.
Copyright1997MicrosoftCorporation.Allrightsreserved.
InternationalCorrectSpellSpellingCorrectionSystem1995byLernout&HauspieSpeech
Products,N.V.Allrightsreserved.
InstallShield3.0.Copyright1997InstallShieldSoftwareCorporation.Allrightsreserved.
PANTONEandotherPantone,Inc.trademarksarethepropertyofPantone,Inc.Pantone,Inc.,
2002.
PortionsCopyright19911996ArthurD.Applegate.Allrightsreserved.
PortionsrelatingtoJPEGCopyright19911998ThomasG.Lane.Allrightsreserved.Portionsof
thissoftwarearebasedontheworkoftheIndependentJPEGGroup.
PortionsrelatingtoTIFFCopyright19971998SamLeffler.Copyright19911997Silicon
Graphics,Inc.Allrightsreserved.

Government Use
Use,duplication,ordisclosurebytheU.S.Governmentissubjecttorestrictionsassetforthin
FAR12.212(CommercialComputerSoftwareRestrictedRights)andDFAR227.7202(Rightsin
TechnicalDataandComputerSoftware),asapplicable.
RUSSIAN CODE SP 16.13330.2011 MOSCOW 2011 ...................................................................................................................1
INTRODUCTION ..............................................................................................................................................................................2
GENERAL REMARKS ..................................................................................................................................................................3
VERIFICATION PROBLEM 1 DESIGN OF MEMBERS FOR COMPRESSION ......................................................................................6
VERIFICATION PROBLEM 2 LATERAL-TORSIONAL BUCKLING OF BEAMS ..................................................................................15
VERIFICATION PROBLEM 3 COMBINED COMPRESSION AND BENDING ABOUT BOTH AXES .........................................................25
March 2014 page i

Russian code SP 16.13330.2011
Moscow 2011
March 2014 page 1 / 33

Autodesk Robot Structural Analysis Professional - Verification Manual for Steel Members Design
INTRODUCTION
This verification manual contains numerical examples for elements of steel structures prepared and
originally calculated by Autodesk Robot Structural Analysis Professional version 2015.
Each problem contains the following parts:

- title of the problem
- specification of the problem
- Robot solution of the problem
- outputs with calculation results and calculation notes

GENERAL REMARKS
If you make first step in Robot program you should select preferences corresponding to your example
using Preferences or Job Preferences (click Tools).
A. Preferences
To specify required regional preferences click Tools / [Preferences...] and in default opened
Preferences dialog box select in combo boxes a needed country (region) and
working / printout language.
B. Job Preferences
To specify required job preferences click Tools / [Job Preferences...] and in default opened
Job Preferences dialog box select preferences corresponding to your structure example
at the left list view and appropriate combo boxes. Below there is a screenshot showing the
selection [Design codes] :

You can create a new Job Preferences with arbitrarily chosen options and parameters ( standards,
materials, databases, load codes etc.) appropriate for required condition under a new name
to make it easier for future work .
In that case choose proper detailed data from [Configuration of Code List] dialog box which is
opened after pressing [More codes] button and e.g. looks as shown below :
If you pick Load combinations from Codes combo box the new list view appears:

Set a selected code on the right list of the box using arrows than press it as the current code .
Press OK.
After the job preferences decisions are set, type a new name in combo box ,e.g.
new Russian code and save it pressing Save Job Preferences icon placed on the top
of [Job Preferences] dialog box. It opens Save Job Preferences dialog box which you should accept
pressing OK.

VERIFICATION PROBLEM 1
design of members for compression
File: SP16_ex_Compression.rtd
TITLE:
Example 1. I-Shape Compressed Column Verification
SPECIFICATION:
Select a C255 (Ry = 240 MPa) I DDSH 40x1 bar to carry an axial dead load of 622 kN and
live load of 1800 kN. Assume the design member is 9 m long, is pinned top and bottom in both axes
and is laterally braced about the z-z axis at the midpoint.
Verify the strength of a defined compression member .
SOLUTION:
You must remember to specify appropriate gm material factor (a new option) in CONFIGURATION
dialog box placed at Steel/Aluminium Design level.
In DEFINITIONS dialog box define a new type of member, laterally braced about the z-z axis
at the midpoint . It can be set in Member type combo-box.

Pre-defined type of member Column may be initially opened.
For a chosen member type press the Parameters button on Members tab
which opens - here - Column MEMBER DEFINITIONPARAMETERS dialog box.
Type a new name in the Member type editable field. Change parameters to meet initial data
requirements of a structure in a current task. In this particular compression case define buckling z-z
parameters. Press Buckling length coefficient Z icon which opens BUCKLING DIAGRAMS dialog box.
Click a last icon.

The new dialog box INTERNAL BRACING will appear with active Buckling Z tab .
In Buckling Z tab define internal support in the middle of the member by typing relative value 0.5
for marked Define manually coordinates of the existing bracings field.
Press OK.
Save the newly-created member type under a new name, e.g. 0,5 Lz bracing :

Number of the member must be

assigned to appropriate name
of Member type.
( It is very important when you verify

different member types.)
In the CALCULATIONS dialog box set for this task:
Verification option Member Verification

Loads cases 1 to 4
Limit state only Ultimate Limit state will be
analyzed so switch off Limit stat Serviceability
Material factor gm =1,025 ;
the 1,025 radio button is switched on by default
in CONFIGURATION dialog box (opened by
[Configuration] button)
Limit slenderness for Main columns on
[Compression] tab ;
radio button selected in LIMIT SLENDERNESS
VALUE dialog box which is opened by [Define]
button placed in CONFIGURATION dialog box

Now, start calculations by pressing Calculations button.
MEMBER VERIFICATION dialog box with most significant results data will appear on screen.
Pressing the line with results for the member 1 opens the RESULTS dialog box with detailed results
for the analyzed member. The views of the RESULTS windows are presented below.
March 2014 page 10 / 33

Simplified results tab
Detailed results tab
March 2014 page 11 / 33

Pressing the [Calc.Note] button in RESULTS Code dialog box opens the printout note for
the analyzed member. You can obtain Simplified results printout or Detailed results printout .
It depends on which tab is active .
The printout note view of Simplified results is presented below.
a) In the first calculation step DDSH 40x1 section was considered. The results are presented
below.
March 2014 page 12 / 33

b) From economical reason try to check a lighter I-section.

Being still in RESULTS- CODE dialog box, delete number of DDSH or type DB section symbol
in the editable field below a drawing of a section and select DB55x2. Press ENTER.
Calculations (and results) are refreshed instantly.
March 2014 page 13 / 33

The results in the form of a Calculation Note for the new selected section are presented below.
March 2014 page 14 / 33

Lateral-torsional buckling of beams
File: SP16_ex_LTB beam.rtd
TITLE:
Example 2. I-Shape Flexural Member Design in Strong-Axis Bending Braced at Midspan
SPECIFICATION:
Verify the strength of the C345 I DB50x1 beam with a simple span of 10.67m. The beam
is braced at the ends and center point. The nominal loads are a uniform dead load of 5,0 kN/m
and a uniform live load of 8,0 kN/m.
SOLUTION:
In DEFINITIONS dialog box define a new type of member, torsional and laterally braced upper flange
about the z-z axis at the midpoint. It can be set in Member type combo-box.
Pre-defined beam member type may be initially opened.
March 2014 page 15 / 33

For chosen member type press the [Parameters ] button on Members tab.
It opens MEMBER DEFINITIONPARAMETERS dialog box.
Type a new name in the Member type editable field. Then, change parameters to meet initial data
requirements of the structure. In this particular bending case set the following lateral-buckling
parameters :
switch on Lateral buckling
select upper load level by pressing proper icon
define appropriate load type by pressing load icon which opens LOAD TYPE dialog box;
for this task the first icon uniform loads

was selected.
define adequate bracings for Lateral buckling .
March 2014 page 16 / 33

To define Lateral buckling length coefficient for this structure press Upper flange button.
It opens LATERAL BUCKLING LENGTH COEFFICIENTS dialog box.
Click the last icon Intermediate bracings. The new dialog box INTERNAL BRACINGS will appear
with automatically active Lateral buckling - Upper flange tab .
In INTERNAL BRACINGS dialog box there are possibilities of defining independent bracings for
buckling and lateral buckling of the marked member type.
In Lateral buckling-upper flange tab define internal support in the middle of the member by typing
typing relative value 0.5 for marked Define manually coordinates of the existing bracings field.
Press OK.
March 2014 page 17 / 33

By pressing [Service] button at

MEMBER DEFINITIONPARAMETERS
dialog box open SERVICEABILITY-
DISPLACEMENT VALUES dialog box in
which limit dispalcements should be
defined.
Save the newly-

created member type
under a new name ,
e.g. as LB 0,5l up
March 2014 page 18 / 33

Number of a member must be

assigned to the appropriate name
of Member type.
It is very important when you verify

different member types.
In the CALCULATIONS dialog box set for this task :

Loads cases no 3 and no 11
Limit state Ultimate and Serviceability Limit state
will be analyzed so switch on both check boxes
the 1,025 radio button is switched on by default in
CONFIGURATION dialog box (opened by
[Configuration] button)
Limit slenderness Defined by the user on
[Compression] tab (radio button selected in LIMIT
SLENDERNESS VALUE dialog box which is
opened by [Define] button placed in
CONFIGURATION dialog box)
March 2014 page 19 / 33

Now, start verifications by pressing [Calculations] button.
Pressing the line with general results for the member 1 opens the RESULTS dialog box with
detailed results for the analyzed member. The view of the RESULTS windows are presented below.
March 2014 page 20 / 33

Displacements results tab
March 2014 page 21 / 33

the analyzed member. You can obtain Simplified results printout or Detailed results printout .
March 2014 page 22 / 33

March 2014 page 23 / 33

For comparison the simplified results for the unbraced beam, no 2 , are presented below.
March 2014 page 24 / 33

combined compression and bending about both axes
File: SP16_ex_Nc_My_Mz.rtd
TITLE:
Example 3. I-shape Subjected to Combined Compression and Bending About Both Axes
SPECIFICATION:
Verify if an C275 I DSZ_50x1 bar has sufficient available strength to support the axial forces and
moments listed below. The unbraced length is 7,70m and the member has pinned ends:
Lefy = Lefz = Lef,b = 7,70 m
section internal forces Material Properties:

C275 Ry = 270 MPa , Ru = 370 MPa
Nc = 800 kN
My = 400 kNm
Mz = 30 kNm
SOLUTION:
For a considered task define manually a new type of member in DEFINITIONS dialog box. It can be
set in Member type combo-box.
March 2014 page 25 / 33

Pre-defined type of member simple bar may be initially opened.
For a chosen member type click the [Parameters] button on Members tab.
It opens MEMBER DEFINITIONPARAMETERS dialog box.
Type a new name in the Member type editable field. Then change parameters to meet initial data
requirements of the current structure. For this particular task for a bar subjected to a combined loads
Nc +My+Mz case :
define buckling parameters - press Buckling length coefficient Y icon which opens
BUCKLING DIAGRAMS dialog box and select non-sway structure radio button
and the first icon with buckling length coefficient Y equal 1,0 ;
March 2014 page 26 / 33

Do the same for the z-z direction.
switch on Lateral buckling

select required load level by pressing a proper icon
select appropriate load type by pressing a load icon which opens LOAD TYPE dialog
box;
For this task the first icon uniform

loads was selected.
March 2014 page 27 / 33

define parameters required for member stability verification - press [More] button
which opens MEMBER DEFINITION-ADDITIONAL PARAMETERS dialog box and click
currently shown Bending moments for stability analysis icon ;
In the newly opened MOMENTS FOR CALCULATIONS OF MEMBER STABILITY dialog

box select a needed scheme icon ;
March 2014 page 28 / 33

Save the newly-created member type

under a new name, e.g. LTB.
MEMBER DEFINITION
PARAMETERS dialog box defined
for this verifications looks like:
In DEFINITIONS dialog box

number of the member must be
assigned to the appropriate name
of Member type.
( It is very important when you verify

different member types).
March 2014 page 29 / 33

In the CALCULATIONS dialog box set for this task :

Loads cases no 1
Limit state only Ultimate Limit state will be
analyzed so switch off Limit stat Serviceability.
And in CONFIGURATION dialog box opened by
[Configuration] button :
the 1,025 radio button is switched on by default
Limit slenderness Defined by the user on
[Compression] tab - radio button selected in LIMIT
SLENDERNESS VALUE dialog box which is opened
by [Define] button .
March 2014 page 30 / 33

Now, start verifications by pressing [Calculations] button.
Pressing a line with results for the member 1 opens the RESULTS dialog box with detailed results for
the analyzed member. The view of the RESULTS windows are presented below.
March 2014 page 31 / 33

the analyzed member. You can obtain Simplified results printout or Detailed results printout.
March 2014 page 32 / 33

March 2014 page 33 / 33

Verification Manual Russian Code SP 16.13330.2011

Uploaded by

Copyright:

Available Formats

Verification Manual Russian Code SP 16.13330.2011

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Verification Manual Russian Code SP 16.13330.2011

Uploaded by

Copyright:

Available Formats

Autodesk

Robot Structural Analysis

March 2014 page i

March 2014 page 1 / 33

Each problem contains the following parts:

March 2014 page 2 / 33

March 2014 page 3 / 33

March 2014 page 4 / 33

March 2014 page 5 / 33

March 2014 page 6 / 33

Pre-defined type of member Column may be initially opened.

Click a last icon.

March 2014 page 7 / 33

March 2014 page 8 / 33

Number of the member must be

( It is very important when you verify

In the CALCULATIONS dialog box set for this task:

Verification option Member Verification

March 2014 page 9 / 33

Now, start calculations by pressing Calculations button.

March 2014 page 10 / 33

Simplified results tab

Detailed results tab

March 2014 page 11 / 33

March 2014 page 12 / 33

b) From economical reason try to check a lighter I-section.

March 2014 page 13 / 33

March 2014 page 14 / 33

Pre-defined beam member type may be initially opened.

March 2014 page 15 / 33

for this task the first icon uniform loads

define adequate bracings for Lateral buckling .

March 2014 page 16 / 33

March 2014 page 17 / 33

By pressing [Service] button at

Save the newly-

March 2014 page 18 / 33

Number of a member must be

It is very important when you verify

In the CALCULATIONS dialog box set for this task :

Verification option Member Verification

March 2014 page 19 / 33

Now, start verifications by pressing [Calculations] button.

March 2014 page 20 / 33

Simplified results tab

Displacements results tab

March 2014 page 21 / 33

Detailed results tab

March 2014 page 22 / 33

The printout note view of Simplified results is presented below.

March 2014 page 23 / 33

Simplified results tab

March 2014 page 24 / 33

section internal forces Material Properties:

March 2014 page 25 / 33

Pre-defined type of member simple bar may be initially opened.

March 2014 page 26 / 33

Do the same for the z-z direction.

switch on Lateral buckling

For this task the first icon uniform