Journal of Advances in Science and Technology

Vol. 13, Issue No. 1, (Special Issue) March-2017, ISSN 2230-9659

Gating System and Feeder Design of Aluminium

Alloy (AA6063) Casting for Rectangular
Component

Kiran R. Jathar1*, Anant V. Hankare2, Amol A. Sapkal3

1,2
P.G.Scholar (Mechanical Engineering) GCE, Karad
3
Assistance Professor, Government college of Engineering, Karad

Abstract In around 80% of components are manufactured by casting process. So there is a lot of scope
for improvement in quality of casting. In today, many industries are struggling for good quality of casting.
Quality of casting is dependent upon flow of liquid melt through gating system. In other words, liquid
melt should enter into the mold cavity within solidification time of melt, so proper design of gating
system is essential study of this project. Proper gating system design reduces the turbulence in the flow
of molten metal, minimize air entrapment, sand inclusion, oxide film and dross. The problems caused by
improper gating system design are aluminium oxide films, cuts and washes, low casting yield and
entrapped gas. This study describes the design of a gating system and feeder to produce Aluminium
alloy casting of rectangular component having length 55mm, breadth 30mm and height 30mm using the
non-pressurized gating system with ratio of 1:4:4 and green sand moulding technique. Thus it is essential
to understand design of gating system and feeder for producing defect free casting. Objective of this
research is to improve the quality of aluminium alloy casting produced in green sand moulding process
through proper gating system design and feeder design.

Keywords Gating System Design, Feeder Design, Green Sand, Aluminium Alloy, Rectangular
Component.

--------------------------------------------------------

INTRODUCTION The elements shown in the fig. 1 are actually cavities

in the sand mold. The sand mold consists of two
Casting processes are widely used to obtain parts: the upper half, or cope and the lower half, or
complicated shapes of metal parts with little or no drag. The plane between the cope and the drag is
machining in a very economical way. The manufacture called the parting plane. The parting plane is
of a part involves several steps (a) Design of part itself sometimes referred to as the parting line when the
(b) Specification of material (c) Design of gating casting is viewed in two dimensions. The vertical
system (d) Design of rigging system (feeder). Two passage through which the molten metal is poured
major casting design considerations are the quality of into the casting is called the sprue or downsprue. The
the final product and the yield of the casting; both are horizontal channels in the parting plane are called the
dependent on the rigging system used. runners. The connections between the runners and
the cavity of the part to be cast are called the gates or
the ingates. Those extra parts of the casting that feed
metal to the casting as it solidifies and shrinks are
called the risers or feeders.

S. Guleyupoglu [1] explained a compilation of

common rules of thumb used by foundry experts and
www.ignited.in

guidelines suggested by researchers for better quality

castings. He has given the guidelines about gating
and risering practice for light alloy, ductile iron and
steel castings. Victor ANJO and Reyaz Khan [2] has
explained the gating system design calculations for
casting thin aluminium alloy(Al-Si) plates using green
Fig. 1 Schematics of the Mold Cavities in Casting sand mould and a non-pressurized gating system
35
Kiran R. Jathar1*, Anant V. Hankare2, Amol A. Sapkal3
 Gating System and Feeder Design OF Aluminium alloy (AA6063) casting for Rectangular Component

with a gating ratio of 1: 4: 4. A coal fired crucible Where, Ac = the cross sectional area of the
furnace is used for the melting of aluminium alloy and Choke.
an X-Ray machine is used to see internal defects in
casting. C. M. Choudharia et al. [3] he has done study Pattern Allowances:
on casting design calculation of cover plate and
numerical simulation using AutoCAST-X software. He There are various types of pattern allowances which
has produced the casting with the help of silica sand are named as draft, machining, distortion, shrinkage
and wooden pattern and finally radiographic test were allowance. Mainly shrinkage allowance is necessary to
performed on final casting to see internal defect. Jong avoid shrinkage defect in the casting. Shrinkage defect
Cheon Park and Kunwoo Lee [4] have been developed is the cavity remains inside the casting after
an interactive computer program to design a pattern solidification. To avoid shrinkage defect in the casting,
and the risers. They included an automatic whole shrinkage allowance is necessary.
elimination, an automatic scaling for shrinkage
allowance and an automatic draft addition for the Turbulence in the metal flow may be caused by
pattern design and also included an automatic excessive velocity of the molten metal, free-falling of
generation of risers and riser necks with their the stream while passing from one level to another,
recommended locations. B.H. Hu et al. [5] has vortices formed, or abrupt changes in the flow
presented a numerical simulation technique used for direction. Sharp changes in the flow direction will form
optimisation of the runner and gating systems for the eddies at the corners, and these will cause aspiration
hot chamber die casting of a thin-walled magnesium of air and mold gases into the molten metal.
telecommunication part. Dr. B. Ravi [6] has presented
an intelligent design environment to assist product Shrinkage allowance for Aluminium alloys is 16mm/m.
engineers in assessing a part design for castability. He These allowances shall be added to the pattern parts
has mentioned design of sprue, runner, gate and in the mould cavity.
feeder on the basis of simulation software.
Pattern Dimension = Actual Dimension + Shrinkage
The aim of this research is design of gating system for allowance (3)
rectangular component and also feeder design
calculations for aluminium alloy material. Original dimensions of component,

GATING DESIGN CALCULATIONS Length=55mm,

Design calculations of gating system for aluminium Breadth=30mm,

alloy is calculated for designing wooden pattern for
producing casting component. Design of gating system Height=30mm.
will help to pour molten metal into mold cavity before
solidification temperature of aluminium alloy. Proper Pattern length = 55+0.05516 = 55.88mm
gating system will help to avoid turbulence flow of
molten metal into the mold cavity. Pattern breadth =30+0.03016 = 30.48mm

For the study on aluminium alloys, we shall be using Pattern height =30+0.03016 = 30.48mm
the non-pressurized gating system with a gating ratio
of: Step 1: Calculate the total weight of castings

As: Ar: Ag = 1: 4: 4 (1) W = V (4)

(Non-pressurized gating ratio) Where: W = total weight of casting,

Where, = density,

As = the cross sectional area of the Sprue V = total volume of casting.

Exit, V = 55.8830.4830.48(10 )
-3 3
www.ignited.in

Ar = the cross sectional area of the Runner, V = 51914.21 mm

3

Ag = the cross sectional area of the Ingate. W = 250051914.21 = 0.1297 Kg

The choke (the smallest cross sectional area) is at the Step 2: Calculate the pouring rate and pouring
sprue base exit therefore. time

As=Ac (2)
36
NC MEND 2017, Organized by Govt. College of Engineering, Karad, Maharashtra
In Association with The Institution of Engineers, PLC
 Journal of Advances in Science and Technology
Vol. 13, Issue No. 1, (Special Issue) March-2017, ISSN 2230-9659

Pouring rate formula for non-ferrous gating: air, and thus an increased oxidation of the metal.
Those oxides may rise to the top of the casting to form
a rough surface for the casting, or they may be
R= (5) trapped in the casting and create imperfections.
Turbulent flow may also cause erosion of the sand
Where, R = pouring rate, mold. To avoid turbulence flow, oxides formed, erosion
proper design of sprue is necessary.
b = constant, depends on wall thickness; Typical
values of b are shown on TABLE I. Sprue height Hsprue = 40 mm
TABLE I Values of Constant (b) for Different Height of casting in the cope H1=5 mm
Casting Thickness
Total height of casting H2=30mm, then using
Casting Below 6 6-12 Above 12 equation (8)
thickness mm mm mm

(mm)
Hp = H- 0.5 (8)
b -constant 0.99 0.87 0.47
Where, Hp = effective sprue height.

Hp = 40 0.5 = 39.58 mm
R = 0.47
Step 4: Calculate the choke cross sectional Area:
R = 0.16926 kg/s
Choke cross sectional area is the smallest cross
sectional area in the gating system which is sprue
exit area used to calculate sprue height and also
Ra = (6) sprue inlet and exit radius.

Where, The flow rate equation:

Ra = adjusted pouring rate,

Ac = (9)
K = metal fluidity,
2
Where, Ac = choke area (mm ),
C = the effect of friction with values of 0.85-0.90 for
tapered sprues in the gating system.
W = casting weight (Kg),
3
= density of molten metal (kg/m ),
t= (7)
Hp = effective sprue height (mm),
Where, t = pouring time.
C = discharge coefficient (0.8),

Ra = = 0.199129 kg/s g = acceleration due to gravity

2
(9.81m/s ),

t= = 0.651336 sec Ra = adjusted pouring rate (Kg/s)

Step 3: Calculate the effective sprue height: t = pouring time (s).

www.ignited.in

The sprue, or downsprue, is the part of the rigging into

Ac =
which the molten metal is poured. The design of the
downsprue is crucial in order to avoid initiation of 2
turbulent flow in the rigging system. Turbulent metal = 112.985 mm
flow might cause an increased area to be exposed to

Kiran R. Jathar1*, Anant V. Hankare2, Amol A. Sapkal3 37

 Gating System and Feeder Design OF Aluminium alloy (AA6063) casting for Rectangular Component

Step 5: calculation of the sprue inlet area, since Where, L = length, B = breath.
sprue exit area Asprue_exit = choke area Ac
Since for a square,
Continuity equation:
Length = Breath,
2
Therefore, Area = (Length)
Asprue-inlet = (10)
Length of Runner cross section = Breath of
Where, Runner cross section.

Asprue-inlet = sprue inlet cross-sectional area, Length of Runner = 21.25mm and Breath of
Runner = 21.25mm.
Asprue-exit = sprue exit cross-sectional area,
Ingate cross-sectional area = 4112.985
Hsprue-inlet = distance between the ladle and sprue
2
top, = 451.94 mm

Hsprue-exit = distance between ladle and sprue exit. Step 7: Design of Sprue well:

Sprue well is the passage of transferring

Asprue-exit = 112.985 mm2 molten metal from sprue exit to runner.

Hsprue-inlet = 50 mm Sprue well cross-sectional area = 5sprue exit area =

2 2
5112.985 mm = 564.925 mm
Hsprue-exit = 50+40 = 90 mm
Sprue well depth = 2runner depth

2 = 221.25 = 42.5mm
Asprue-inlet = 112.985 = 151.58 mm
DESIGN OF FEEDER
Radius of the sprue inlet:
Risers are reservoirs of molten metal that are used to
feed the casting during solidification. The shrinkage
occurring during solidification causes voids unless
Rinlet = = more molten metal can be fed to the potential
problem spots. Risers are designed to solidify last
= 6.946 mm and to draw the shrinkage voids out of the casting.
Risers also serve as exits for gases and dross
Radius of the sprue exit: entrapped in the metal and as pressure heads to feed
thin sections.

For the greatest efficiency, for small casting, riser

Rexit = = should be cylindrical.

= 5.997 mm According to Chvirinos rule:

Step 6: Calculation of the Ingate and Runner cross-

sectional areas using a gating ratio of 1: 4: 4: ( ) riser > ( ) casting

Gates are the passages between the runners Volume of riser = 0.47 Volume of casting
and the part. Runners are the passages that carry the
molten metal from the sprue well to the gates through = 0.47 (55 30 30)
www.ignited.in

which metal enters the mold cavity.

3
= 23265 mm
Runner cross-sectional area = 4112.985
2
= 451.94 mm
= 23265
Area of a Square = LB

38
NC MEND 2017, Organized by Govt. College of Engineering, Karad, Maharashtra
In Association with The Institution of Engineers, PLC
 Journal of Advances in Science and Technology
Vol. 13, Issue No. 1, (Special Issue) March-2017, ISSN 2230-9659

film and dross while pouring molten metal into the

For the top riser, H = casting cavity. From the feeder design calculation it
has been seen that the dimensions of height, diameter
and modulus for top feeder are 19.48, 38.98 and 6.49
3 respectively and for side feeder 30.94, 30.94 and 5.15
D = 23265
respectively.
3
D = 59243.836
Table II Design Calculations of Gating System
D = 38.98 mm
Part Height Length Width

(mm) (mm) (mm)

H = = 19.49 mm
Pouring
For side riser, H = D basin
30 30 30
2
D H = 23265 Sprue 40 Inlet Outlet
Radius=7 Radius=6
3
D = 23265

D = 30.94 mm Sprue
Well
H = D = 30.94 mm 25 25 25

Modulus of riser: Runner 15 22 22

Ingate 10 15 10
For top riser, M = = = 6.496 mm

Table III Design Parameters of Feeder

For side riser M = = = = 5.156 mm
Feeder Height Diameter Modulus
Type
RESULTS AND DISCUSSION (mm) (mm) (mm)
After the calculations of the gating system dimensions Top 19.49 38.98 6.496
and the pattern allowances values obtained is transfer Feeder
to the wooden pattern and gating in order to make the
mould. The mould cavity is produced by placing the
Side 30.94 30.94 5.156
pattern in a wood frame, filling it with the green sand
Feeder
mix and properly ramming the sand mix with the
pattern in it to give the mould strength. After the
pattern is removed, the mould is assembled back
together. Fig. 1 shows the schematics of the mould CONCLUSIONS
cavities and gating produced by the wood pattern and
gating. Aluminium alloy is then charged into the Deign calculations of gating system for aluminium
melting furnace to get molten metal to pour into the alloy casting with a non-pressurized gating system of
mold cavity. After solidification and cooling casting is gating ratio 1:4:4 in a green sand molding process
taken out of the mold and cleaned from sand particles. are calculated to get good quality of a casting. And
also the feeder design parameters are calculated to
Design calculations of the gating system are shown in avoid shrinkage defects in the casting. Proper feeder
the TABLE II and design parameters of the feeder are design parameters and its location will help to
www.ignited.in

shown in the TABLE III. transfer shrinkage defect into the feeder. With the
help of proper design parameter of gating system and
Proper design of gating calculations helps to avoid feeder, defect free casting can be produced.
aspiration effect, turbulence in the flow of molten
metal, minimize air entrapment, sand inclusion, oxide

Kiran R. Jathar1*, Anant V. Hankare2, Amol A. Sapkal3 39

 Gating System and Feeder Design OF Aluminium alloy (AA6063) casting for Rectangular Component

ACKNOWLEDGMENT

I would like to thank Dr. S.S.Mohite; Head of Corresponding Author

Mechanical Engineering Department that have always
been prepared to offer me help at any time, in spite of Kiran R. Jathar*
having busy schedule. Finally I would like to thank R &
D department for financial support. P.G. Scholar (Mechanical Engineering) GCE, Karad

REFERENCES E-Mail kiranjathar1991@gmail.com

[1] S. Guleyupoglu, Casting Process Design

Guidelines, Concurrent Technologies
Corporation Johnstown, Pennsylvania, AFS
Transactions, pp-869-876.

[2] Victor ANJO and Reyaz Khan, Gating System

Design for Casting thin Aluminium Alloy (Al-Si)
Plates, Leonardo Electronic Journal of
Practices and Technologies, ISSN 1583-1078,
2013, pp. 51-62.

[3] C. M. Choudharia, B. E. Narkhedea and S. K.

Mahajan, Casting Design and Simulation of
Cover Plate using AutoCAST-X Software for
Defect Minimization with Experimental
Validation, Procedia Materials Science, vol-6,
(2014), pp. 786 797.

[4] Jong Cheon Park and Kunwoo Lee,

Computer Aided Design of a Pattern and
Risers for Casting Processes: Part 1, Journal
of Engineering for Industry, Vol. 113, February
(1991), pp. 59.

[5] B.H. Hu, K.K. Tong, X.P. Niu, I. Pinwill,

Design and optimisation of runner and gating
systems for the die casting of thin-walled
magnesium telecommunication parts through
numerical simulation, Journal of Materials
Processing Technology, (2000), vol-105, pp-
128-133.

[6] Dr. B. Ravi, Design for Casting, Institute of

Indian Foundrymen, SOURECON99, May 29,
(1999), Hyderabad.

[7] Rajput R.K., Manufacturing Technology, Metal

Casting, third edition, Laxmi Publications Ltd,
New Delhi, India, 2007, p. 46-59.

[8] Jain P.L., Principles of Foundry Technology,

fourth edition, McGraw-Hill ed, New Delhi,
India, 2003, p. 176-184.
www.ignited.in

[9] Campbell J., Castings, Linacre House, Jordan

Hill, Oxford, Butterworth-Heinemann Ltd.,
1991.

[10] Rao P.N., Manufacturing Technology,

Foundry, Forming and welding, third edition,
The McGraw-Hill Company Limited, New
Delhi, India, 2009, p. 128-138.
40
NC MEND 2017, Organized by Govt. College of Engineering, Karad, Maharashtra
In Association with The Institution of Engineers, PLC