Jotatemp 650 (ENG)

Technical Data
Jotatemp 650
Product description
Jotatemp 650 is a high-build, one-component Inert Multipolymeric Matrix coating designed to provide corrosion
protection of structures exposed to extreme high and /or extreme low temperatures.
Recommended use
Corrosion protection of insulated and none -insulated carbon steel and stainless steel with dry operating surface
temperatures that can range from cryogenic to above 650C (intermittent 720C) including cyclic services in
temperatures between -185C and 540C. Jotatemp 650 can be applied on hot substrates (up to 260C). Especially
suited for preventing corrosion under insulation during construction and shut down /low temperature periods.
Film thickness and spreading rate

Minimum Maximum Typical
Film thickness, dry (m) 100 150 125
Film thickness, wet (m) 135 200 165
Theoretical spreading rate (m/l) 7.6 5.1 6.1
Physical properties
Colour Grey, Aluminium effect
Solids (vol %)* 76 2
Flash point 18C 2 (Setaflash)
VOC 3.5 lbs/gal (424 gms/ltr) USA-EPA Method 24
453 gms/ltr UK-PG6/23(97). Appendix 3
Gloss Flat
Water resistance Good
Solvent resistance Fair
Chemical resistance Fair
Flexibility Good
*Measured according to ISO 3233:1998 (E)
Hong Kong rules:

Category of paints - Other vessel coatings; VOC 424 gms/ltr HK EPD method (Ready to use); Exempt
compound - N/A; Specific gravity: 1.95 gms/ltr; Both VOC and Specific gravity values provided are typical
values, subject to changes when different colour involved .
Surface preparation
All surfaces should be clean , dry and free from contamination . The surface should be assessed and treated in
accordance with ISO 8504.
Bare steel
Cleanliness: Power tool cleaning to min. St 2, mill scale free (ISO 8501-1:2007) and a roughness between 35 - 50
microns. Improved surface treatment (blast cleaning to Sa 2) will improve the performance .
Other surfaces
The coating may be used on other substrates . Please contact your local Jotun office for more information .
Jotatemp 650 (English TDS) Page 1

Condition during application
The temperature of the substrate should be minimum 10C and at least 3C above the dew point of the air ,
temperature and relative humidity measured in the vicinity of the substrate . The coating should not be exposed to oil ,
chemicals or mechanical stress until fully cured .
Application methods
Spray Use airless spray
Brush May be used but care must be taken to achieve the specified dry film thickness .
Application data
Mixing ratio (volume) Single pack.
Thinner/Cleaner Jotun Thinner No. 21
Guiding data airless spray
Pressure at nozzle 15 MPa (150 kp/cm, 2100 psi)
Nozzle tip 0.38-0.53 mm (0.015-0.021")
Spray angle 40-80
Filter Check to ensure that filters are clean .
Note For substrate temperatures lower than 100C Jotun Thinner No. 7 can be used.
Drying time
Drying times are generally related to air circulation , temperature, film thickness and number of coats , and will be
affected correspondingly . The figures given in the table are typical with :
* Good ventilation (Outdoor exposure or free circulation of air )
* Typical film thickness
* One coat on top of inert substrate
Substrate temperature 10C 15C 23C 40C 100C

Surface dry 8-10 h 6h 2h 2h 0,5 h
2
Through dry 24 h 24 h 6h 6h 1h
1
Dry to recoat, minimum 24 h 24 h 6h 4h 1h
1. The surface should be free from chalking and contamination prior to application .
2. Exposure to extreme temperature, below 0C and above 260C, should be avoided before the coating is
through dry.
The given data must be considered as guidelines only . The actual drying time/times before recoating may be shorter
or longer, depending on film thickness , ventilation, humidity, underlying paint system, requirement for early handling
and mechanical strength etc . A complete system can be described on a system sheet , where all parameters and
special conditions could be included .
Typical paint system

Jotatemp 650 2 x 125 m (Dry Film Thickness)
Optional system:
Jotatemp 650 3 x 125 m (Dry Film Thickness)
Other systems may be specified, depending on area of use

Storage
The product must be stored in accordance with national regulations . Storage conditions are to keep the containers in
a dry, cool, well ventilated space and away from source of heat and ignition . Containers must be kept tightly closed .
Handling
Handle with care. Stir well before use.
Packing size
5 litre unit.
Health and safety

Please observe the precautionary notices displayed on the container . Use under well ventilated conditions . Do not
breathe or inhale mist. Avoid skin contact. Spillage on the skin should immediately be removed with suitable
cleanser, soap and water. Eyes should be well flushed with water and medical attention sought immediately .
For detailed information on the health and safety hazards and precautions for use of this product , we refer to
the Material Safety Data Sheet.
DISCLAIMER
The information in this data sheet is given to the best of our knowledge based on laboratory testing and practical
experience. However, as the product can be used under conditions beyond our control , we can only guarantee the
quality of the product itself . We also reserve the right to change the given data without notice . Minor product
variations may be implemented in order to comply with local requirements .
If there is any inconsistency in the text the English (UK) version will prevail.
Jotun is a World Wide company with factories , sales offices and stocks in more than 50 countries. For your nearest local Jotun
address please contact the nearest regional office or visit our website at www.jotun.com
ISSUED 9 DECEMBER 2011 BY JOTUN

THIS DATA SHEET SUPERSEDES THOSE PREVIOUSLY ISSUED
PDF Version :

Jotatemp 650 (ENG)

Uploaded by

Copyright:

Available Formats

Jotatemp 650 (ENG)

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Jotatemp 650 (ENG)

Uploaded by

Copyright:

Available Formats

Technical Data

Film thickness and spreading rate

Hong Kong rules:

Jotatemp 650 (English TDS) Page 1

Substrate temperature 10C 15C 23C 40C 100C

Typical paint system

Other systems may be specified, depending on area of use

Jotatemp 650 (English TDS) Page 2

Health and safety

ISSUED 9 DECEMBER 2011 BY JOTUN

Jotatemp 650 (English TDS) Page 3

You might also like