Sharp LC-46XL1E PDF

LC-46XL1E/RU, LC-52XL1E/RU
SERVICE MANUAL
No. S67J4LC46XL1E
LCD COLOUR TELEVISION
LC-46XL1E/RU
MODELS LC-52XL1E/RU
In the interests of user-safety (Required by safety regulations in some countries) the set should be restored to its orig-
inal condition and only parts identical to those specified should be used.
CONTENTS
SAFETY PRECAUTION [4] POWER BLOCK DIAGRAM
IMPORTANT SERVICE SAFETY (LC-52XL1E/RU) ...........................................6-4
PRECAUTION.....................................................i [5] WIRING DIAGRAM (LC-46XL1E/RU) ...........6-5
Precautions for using lead-free solder ...............ii [6] WIRING DIAGRAM (LC-52XL1E/RU) ...........6-6
CHAPTER 1. OPERATION MANUAL CHAPTER 7. PRINTED WIRING BOARD

[1] SPECIFICATIONS ......................................... 1-1 [1] MAIN UNIT PRINTED WIRING BOARD........7-1
[2] OPERATION MANUAL .................................. 1-2 [2] AV UNIT PRINTED WIRING BOARD............7-5
[3] DIMENSIONS ................................................ 1-5 [3] DIGITAL UNIT PRINTED WIRING
BOARD..........................................................7-8
CHAPTER 2. REMOVING OF MAJOR PARTS [4] D-TUNER UNIT PRINTED WIRING
[1] REMOVING OF MAJOR PARTS BOARD........................................................7-12
(LC-46XL1E/RU) ............................................ 2-1 [5] KEY UNIT PRINTED WIRING BOARD .......7-13
[2] REMOVING OF MAJOR PARTS [6] R/C, LED UNIT PRINTED WIRING
(LC-52XL1E/RU) .......................................... 2-11 BOARD........................................................7-13
[7] ILLUMINATION UNIT PRINTED WIRING
CHAPTER 3. ADJUSTMENT PROCEDURE BOARD........................................................7-14
[1] ADJUSTMENT PROCEDURE ....................... 3-1 [8] FRC UNIT PRINTED WIRING BOARD .......7-15
[9] POWER UNIT PRINTED WIRING
CHAPTER 4. TROUBLESHOOTING TABLE BOARD........................................................7-19
[1] TROUBLESHOOTING TABLE....................... 4-1
CHAPTER 8. SCHEMATIC DIAGRAM
CHAPTER 5. MAJOR IC INFORMATIONS [1] DESCRIPTION OF SCHEMATIC
[1] MAJOR IC INFORMATIONS.......................... 5-1 DIAGRAM......................................................8-1
[2] SCHEMATIC DIAGRAM ................................8-2
CHAPTER 6. BLOCK DIAGRAM/WIRING DIAGRAM
[1] BLOCK DIAGRAM (LC-46XL1E/RU) ............. 6-1 Parts Guide
[2] BLOCK DIAGRAM (LC-52XL1E/RU) ............. 6-2
[3] POWER BLOCK DIAGRAM
(LC-46XL1E/RU) ............................................ 6-3
Parts marked with " " are important for maintaining the safety of the set. Be sure to replace these parts with specified ones for maintaining the
safety and performance of the set.
This document has been published to be used for

after sales service only.
The contents are subject to change without notice.
LC46XL1E
SAFETY PRECAUTION Service Manual
IMPORTANT SERVICE SAFETY PRECAUTION

Service work should be performed only by qualified service technicians who are thoroughly familiar with all safety checks and the
servicing guidelines which follow:
WARNING Use an AC voltmeter having with 5000 ohm per volt, or higher, sen-
sitivity or measure the AC voltage drop across the resistor.
1. For continued safety, no modification of any circuit should be
attempted. Connect the resistor connection to all exposed metal parts having a
return to the chassis (antenna, metal cabinet, screw heads, knobs
2. Disconnect AC power before servicing.
and control shafts, escutcheon, etc.) and measure the AC voltage
drop across the resistor.
All checks must be repeated with the AC cord plug connection
reversed. (If necessary, a nonpolarized adaptor plug must be used
CAUTION: only for the purpose of completing these checks.)
FOR CONTINUED PROTECTION AGAINST A Any reading of 1.05 V peak (this corresponds to 0.7 mA peak AC.)
RISK OF FIRE REPLACE ONLY WITH SAME or more is excessive and indicates a potential shock hazard which
TYPE FUSE. must be corrected before returning the monitor to the owner.
F701 (6.3A/250V)
DVM
BEFORE RETURNING THE RECEIVER AC SCALE
(Fire & Shock Hazard)
Before returning the receiver to the user, perform the following 1.5k ohm
safety checks: 10W
3. Inspect all lead dress to make certain that leads are not pinched,
and check that hardware is not lodged between the chassis and
other metal parts in the receiver.
4. Inspect all protective devices such as non-metallic control knobs, 0.15 F
insulation materials, cabinet backs, adjustment and compartment TEST PROBE
covers or shields, isolation resistor-capacitor networks, mechanical
insulators, etc.
5. To be sure that no shock hazard exists, check for leakage current in
the following manner.
Plug the AC cord directly into a 220~240 volt AC outlet. TO EXPOSED CONNECT TO
METAL PARTS KNOWN EARTH
Using two clip leads, connect a 1.5k ohm, 10 watt resistor paral- GROUND
leled by a 0.15F capacitor in series with all exposed metal cabinet
parts and a known earth ground, such as electrical conduit or elec-
trical ground connected to an earth ground.
///////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
SAFETY NOTICE
Many electrical and mechanical parts in LCD color television have For continued protection, replacement parts must be identical to those
special safety-related characteristics. used in the original circuit.
These characteristics are often not evident from visual inspection, nor The use of a substitute replacement parts which do not have the same
can protection afforded by them be necessarily increased by using safety characteristics as the factory recommended replacement parts
replacement components rated for higher voltage, wattage, etc. shown in this service manual, may create shock, fire or other hazards.
Replacement parts which have these special safety characteristics are
identified in this manual; electrical components having such features
are identified by and shaded areas in the Replacement Parts
List and Schematic Diagrams.
///////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
i
Precautions for using lead-free solder
Employing lead-free solder

PWBs of this model employs lead-free solder. The LF symbol indicates lead-free solder, and is attached on the PWBs and service manuals. The
alphabetical character following LF shows the type of lead-free solder.
Example:
LFa L F a/a
Indicates lead-free solder of tin, silver and copper. Indicates lead-free solder of tin, silver and copper.
Using lead-free wire solder

When fixing the PWB soldered with the lead-free solder, apply lead-free wire solder. Repairing with conventional lead wire solder may cause dam-
age or accident due to cracks.
As the melting point of lead-free solder (Sn-Ag-Cu) is higher than the lead wire solder by 40 C, we recommend you to use a dedicated soldering
bit, if you are not familiar with how to obtain lead-free wire solder or soldering bit, contact our service station or service branch in your area.
Soldering
As the melting point of lead-free solder (Sn-Ag-Cu) is about 220 C which is higher than the conventional lead solder by 40 C, and as it has poor
solder wettability, you may be apt to keep the soldering bit in contact with the PWB for extended period of time. However, Since the land may be
peeled off or the maximum heat-resistance temperature of parts may be exceeded, remove the bit from the PWB as soon as you confirm the
steady soldering condition.
Lead-free solder contains more tin, and the end of the soldering bit may be easily corroded. Make sure to turn on and off the power of the bit as
required.
If a different type of solder stays on the tip of the soldering bit, it is alloyed with lead-free solder. Clean the bit after every use of it.
When the tip of the soldering bit is blackened during use, file it with steel wool or fine sandpaper.
Be careful when replacing parts with polarity indication on the PWB silk.
Lead-free wire solder for servicing
Part No. Description Code
ZHNDAi123250E J 0.3mm 250g (1roll) BL
ZHNDAi126500E J 0.6mm 500g (1roll) BK
ZHNDAi12801KE J 1.0mm 1kg (1roll) BM
ii
CHAPTER 1. OPERATION MANUAL
LC46XL1E
Service Manual
[1] SPECIFICATIONS
11
[2] OPERATION MANUAL
12
13
Remote control unit

NOTE 1 2 3 15 (INPUT SOURCE)
The symbols , and Select an input source.
indicate that the buttons become (TV, DTV, EXT1, EXT2, EXT3, EXT4,
available in respective operating mode EXT5, EXT6)
when using as a universal remote 16 MENU
control. TV: MENU screen on/off.
1 (TV Standby/On) 4 DVD: Title menu on/off.
17 EPG
2 LIGHT DTV: To display EPG (Electronic
When pressed buttons that are Programme Guide) screen.
frequently used(P / , / , 18 P( / )
0 - 9 numeric buttons, and ) 5 Select the TV channel.
will light. The lighting will turn off if In analogue TV mode, external input
no operations are performed within sources (EXT 1 - 6) can also be
about 5 seconds. This button is used selected.
for performing operations in low-light 6 15
19 (Display information)
situations. 7 16
3 FUNCTION
8 17 20 (Return)
Press this button briefly (for more than
0.2 second), and the remote control 9 18 Return to the previous menu screen.
switches for DVD, SetTopBox or VCR 21 Buttons for other useful features
operation and currently controlled device 10 19 Flip open the remote control cover on
will be indicated in the LCD window.
the front.
See page 37 for how to use this unit as
a universal remote control. 11 RADIO
4 LCD window DTV: Switch between RADIO and DTV
This screen shows which device you are 12 mode.
currently controlling. (TV, DVD, STB or SURROUND
VCR).
13 20 Surround effects on/off.
5 09 (Sound mode)
Set the channel in TV and DTV mode. 14 Select the sound multiplex mode.
Enter the desired numbers or letters.
Set the page in Teletext mode.
AV MODE
6 (Flashback)
Press to return to the previous image in
21 Select a video setting.
normal viewing mode. SLEEP
7 DTV MENU
22 Set the sleep timer on (in units of 30
DTV: Display DTV Menu screen. 23 min. up to max. 2hr. 30min) and off.
(If the Time and date screen is
8 DTV displayed, enter the time and date,
Press to access DTV mode while and set the sleep timer again.)
watching other input sources, and vice
versa. OPC
(Will not work if you were watching
To switch the Optical Picture Control on
DTV immediately before turning off the
and off.
TV. In this case rst select any other
input source except DTV using the DEMO
button.) 14 Buttons for teletext Demonstrate the 100Hz effects in a dual
9 ( / ) (Volume) (Subpage) screen format.
Increase/decrease TV volume. (Wide modes)
10 (Mute) (Teletext) Select the wide mode.
TV sound on/off TV: Display the analogue teletext. 22 AQUOS LINK buttons
11 Colour (Red/Green/Yellow/Blue) If external equipment such as AQUOS
DTV: Select DTV data broadcasting and BD Player is connected via HDMI cables
TELETEXT: Select a page. TELETEXT. and AQUOS LINK compatible, you can
The coloured buttons are used to select (Freeze/Hold) use these AQUOS LINK buttons.
correspondingly to the coloured items in
the menu screen. In DVD or VCR mode, press OPTION to
12 / / / (Cursor) (Reveal hidden Teletext) pause the picture.
Not available when operating STB
Select a desired item on the setting
except powering on the device.
screen. (Subtitle for Teletext)
23 REC and REC STOP buttons
OK TV/External: Subtitle on/off.
TV/DTV/DVD/STB: Execute a command DTV: Display the subtitle selection screen.
within the menu screen.
TV/DTV: Display the station list in (Top/Bottom/Full)
analogue mode and the programme list Set the area of magnification in analogue
in DTV mode. teletext mode.
13 END
Exit the menu screen.
14
[3] DIMENSIONS
( ) : LC-46XL1E/RU
[ ] : LC-52XL1E/RU
: LC-46XL1E/RU
LC-52XL1E/RU
Unit:mm
660.0
(1137.0 ) / [1273.0] (96.0 ) / [95.0] (124.4 ) / [125.5]
(1021.4 ) / [1155.0]
(796.0 ) / [875.0]
(733.0 ) / [812.0]
(575.4 ) / [651.0]
(450.0 ) / [490.0]
63.0
309.0
200.0
100.0
200.0
15
CHAPTER 2. REMOVING OF MAJOR PARTS
LC46XL1E
Service Manual
[1] REMOVING OF MAJOR PARTS (LC-46XL1E/RU)

1. Remove the 13 lock screws 1 , 4 lock screw 2 and the 4 lock screws 3 . Detach the Rear Cabinet.
2
3
Rear Cabinet
2. Remove the 4 lock screws 4 and detach the Bottom Cover.
Bottom Cover -Rear

Bottom Cover -Front
21
3. Remove the 1 lock screw 5 and the 2 lock screws 6 . Detach the Earth Abgle.
Earth Angle
< Check >

No float of FPC in this area
4. Remove the 8 lock screws 7 and detach the Stand Angle.
# In stand angle installation, position while

pulling ferrite core to arrow direction
7 Stand Angle
Wire "SP" to WH
22
5. Remove the 2 lock screws 8 and the 4 lock screws 9 . Detach the Center Angle Assy.
#Caution
Make sure Gasket shape like this.
9
When install center angle, be careful

so that gasket doesn't come off
Center Angle Ass'y
Don't sandwich wire "SP"
6. Remove the KM connectors from the KEY PWB.
Wire "KM" to WH
Wire "KM" (to P151) Top Cover Ass'y
Wire "KM" to WH
23
7. Remove the 1 lock screw 10 and the 5 lock screws 11 . Detach the Full Shield.
11 10
BTM
Lock side
Top
Wire Holder
Wire "SP" Wire "SP", "RA" into Edge
Wire "RA"
# Push slack of Wire "SP" into Full-
Full Shield
8. Remove the SP wire from the wire holders.
For prevention to sandwich between molding parts
Ferrite Core (to SP-Box Wire "L")
Wire "SP" to pin

# Hold wire "RA" by wire "SP"
Never overlap the boss by wire Never overlap the boss by wire
24
9. Remove the SP wire.
Remove the 2 lock screws 12 and detach the Speaker L & R.
12
Wire "SP" (to P301) Wire "RA","SP" to WH SP Box SP Box
Ferrite Core (to Wire "SP")
Red/Black of Wire "SP" --> to SP-BOX "R" White/Black of Wire "SP" --> to SP-BOX "L"
Wire "SP" to WH
10.Remove the 4 lock screws 13 and detach the FRC Cover Sub Assy.
13
FRC Cover Sub Ass'y
25
11.Remove all the connectors from PWBs.
Tape
45
Wire "RA" (to P2303)
Wire "RA" to WH
# Wind wire "RA" to WH 1 turn
Ferrite Core (to Wire "RA")
12.Remove the 1 lock screw 14 and detach the R/C, LED Unit.
14
R/C, LED Unit
Wire "RA" to WH
Wire "RA" (to P101)
Wire "RA" to pin
# Shape like this
Illumination Unit
Wire "RA" (to P901)
Shape wire "RA" to pin inside

26
< Detail "A" >
# to Wire "LC" and "LB" # to Wire "LC"

Wire Tie (Wire "LA", "LC")
Ferrite Core Ferrite Core
Wire "LB" to WH
Wire "LA" (to CN7401) Wire "LA" (to CN7601)
Wire "LV" (SC2302 to SC6281)
Wire "LA","LB","LC" to WH
Wire "LB" (to CN7402) Wire "LA" "LC" to WH
Wire "PL","LV" to WH
Ferrite Core (to Wire "LV") Wire "LF (D)" (to P4801) Wire "PL" (to CN3) # Not Wire "LF (D)"
27
14.Remove the 5 lock screws 15 and detach the Chassis Tray Sub Assy.
Chassis Tray Sub Ass'y
15
Hole
Lock side
Lock side
Wire Holder
Lock side
Wire Holder
15.Remove the 4 lock screws 16 and detach the Chassis FRC Angle.
Wire Holder
Lock side
16
FRC Unit FRC Angle
LCD_C-FRC(11P)
LCD_C-FRC(FPC)
# Character is outside
28
16.Remove the 4 lock screws 17 and the 8 lock screw 18 . Detach the LCD Side Angle.
18
17
LCD Panel
LCD Side Angle
Cabinet-A Ass'y
Base of LCD Panel positioning
29
17.Remove the 1 lock screw 19 and the 2 lock screws 20 . Detach the D-Tuner Unit.
Wire "KM"
Wire "PL"
Wire "LF (D)"

20 D-Tuner Unit
B to B connector (to SC2705 / SC2707)
19
Chassis Tray Unit
Wire "LB" Wire "LA"
2 10
[2] REMOVING OF MAJOR PARTS (LC-52XL1E/RU)
1. Remove the 18 lock screws 1 , 4 lock screw 2 and the 4 lock screws 3 . Detach the Rear Cabinet.
2
3
Rear Cabinet
2. Remove the 4 lock screws 4 and detach the Bottom Cover.
BOTTOM COVER F
BOTTOM COVER R
2 11
3. Remove the 1 lock screw 5 and the 2 lock screws 6 . Detach the Earth Abgle.
4. Remove the 8 lock screws 7 and detach the Stand Angle.
6 Earth Angle
5 7
STAND ANGLE
< CAUTIONS >
# Do Not sandwich wire "RA","SP"
5. Remove the 4 lock screws 8 and detach the Center Angle Assy.
#Caution
Make sure Gasket shape like this.
Center Angle Ass'y

View A
< CAUTIONS > "TOP" Printing

# Do Not sandwich wire "SP"
2 12
6. Remove the KM connectors from the KEY PWB.
Wire "KM" to WH
KS TOP COVER
Wire "KM"
# No Screw
7. Remove the SP wire.
Remove the 2 lock screws 9 and detach the Speaker L & R.
< CAUTIONS >

# Do Not sandwich wire "RA"
SPEAKER
Detach wire "SP".

Set to connecter holder
of cabinet. For SP-lead
#Caution
Wire "RA" Wire "SP" Wire "RA" grow straight,don't get loose.
Wire "RA" to pin of cabinet Set Wire "RA" along Cabinet lib.
Wire "RA","SP" to pin of cabinet
For SP-lead
Set Wire "RA"
Under Set Wire "SP" Wire "SP" to pin of cabinet
Upper
2 13
8. Remove the 4 lock screws 10 and detach the FRC Cover.
10
FRC COVER
9. Remove all the connectors from PWBs.
#Caution
FPC Connection Direction
Letter printing
side to outside
LCD_C-FRC(FPC)
#Connect to FRC UNIT

Wire "LV" to SC6281 #Connect to FRC LCD_CONTROLER
#Caution
Set Wire "LV" upper to Wire "LP"
LCD_C-FRC(11P)
Wire "LV","PL" to WH
Wire "D" to P4801
Wire "PL" to CN3
for "LV" wire
2 14
10.Remove the 4 lock screws 11 and detach the FRC Angle
11
FRC ANGLE
11.Remove the 4 lock screws 12 and the 8 lock screws 13 . Detach the LCD Side Angle.
12.Remove the 5 lock screws 14 and detach the Chassis Tray Sub Assy.
Chassis Tray Sub Ass'y
14
13
12
< CAUTIONS > LCD Side Angle

# Do Not sandwich wire "RA"
2 15
13.Remove the 1 lock screw 15 and detach the R/C, LED Unit.
WIRE HOLDER
Wire "RA" to LED PWB
Wire "RA"
#Insert
R/C, LED Unit

FOR Wire "RA"
Wire "RA" to ILLUMINATION

Wire "SP"
#Lock
FOR Wire "RA"
15
Wire "LA"
#Brown,Black,
Black Wire Wire "LB" to WH Chassis Tray Unit
Wire "LB" Wire "LB"

Wire "LA"
Wire "LA" #White,Black,
Black Wire
Wire "LC",LA" to WH
#NO Shape/Lock Wire "LB" to this WH
Wire "LA"
Wire "LB"
Wire "LA"
Wire "LC",LA" to WH
For Wire "LC"
Wire "LC"
For Wire "LC"
Wire "LC"
#Wire "LC" and "LA".
Stop to move Core
2 16
SMPL_PANEL_MDL
WIRE HOLDER
KS FRONT CABINE
Base of LCD Panel

positioning
ILLUMINATION
#Insert #Insert
Wire "RA" to WH
Wire "SP" to WH
#Connector Side dwon
15.Remove the 5 lock screws 16 and the 1 lock screw 17 . Detach the Full Shield.
< CAUTIONS >

# Do Not sandwich wire "KM"
FULL SHIELD
16
Wire "KM" to WH
< CAUTIONS >

# Do Not sandwich wire "RA","SP"
17
Wire "RA" Wire "SP"
2 17
Wire "KM"
Wire "LV" (to P2305)
RA:MAIN-RC
#Shape/Lock Wire "RA" to
#View from right side Digital Sheild Angle
FOR Wire "RA"
Wire "SP" Wire "LB"
Wire "LA"
Wire "RA" to WH
Wire "RA"
Wire "SP","RA" to WH Wire "SP"
17.Remove the 1 lock screw 18 and the 2 lock screws 19 . Detach the D-Tuner Unit.
19
B to B connector
Tuner Unit
18
Chassis Tray Unit
2 18
CHAPTER 3. ADJUSTMENT PROCEDUREService
LC46XL1E
Manual
[1] ADJUSTMENT PROCEDURE

The adjustment values are set to their optimum at the factory before shipping.
If by any chance a value should become improper or a readjustment is required due to part replacement, make an adjustment according to the follow-
ing procedure.
1. After replacement of any PWB and/or IC for repair, note the following.
When replacing the following units, be sure to prepare the new units loaded with updated software.
MAIN-UNIT: DUNTKD915FM01
NOTE: That an IC into which ROM data is written is available for MAIN-UNIT servicing (see below).
IC1901 VHi24LC2BiNQES EDID (HDMI)
IC1902 VHi24LC2BiNRES EDID(HDMI)
IC2303 RH-iXB731WJZZS EDID(PC)
2. Software Upgrade 3. Double click on starter.exe and running.
Main software update procedure of SHARP LCDTV

1. Connect your PC and LCDTV by 232C-CROSS-CABLE.
Set up starter298
2. Decompress starter_298_ver100.zip.
31
4. Set the parameters of the starter software as below. 3) Download: set configuration as below.
i) [Options]-[Preferences] Setup window will be opened.
1) General, Terminal, System update: no need to modify (a) set directory path of starter tool
(b) set absolute path of target elf file
anything.
(c) set simple or packed (e) set absolute path of "Cbus_flash_NoUART_

ver1.00.txt" for Cbus(flash).
Starter_298\Configs\Cbus_flash_NoUART_
ver1.00.txt
2) Connection: set COM port number and configuration on (d) set absolute path of "Cbus_boot_ver1.00.txt" for Cbus(boot).
your PC. Starter_298\Configs\Cbus_boot_ver1.00.txt
5. [File]-[Save as] you can save above settings as file name as you
want.
Setting "9600"
32
Download 9. Input "fpga 3 0x80" command and return key on your PC, and the
6. Connect to the LCD TV and start up starter298 software.
in small letters
7. After turn on the power of set, please push the below connect but-
ton. LCD TV is turned off automatically.
NOTE: If set power was turned off and on with this condition, strange
character will be appear, so if this strange character appear,
please ignore.
8. Input "USEROFF" command (non-visited) and return key on your

PC. (get "OK"message)
in capital letters
Input "DPON" command and return key on your PC. (get "MSH>"
message)
in capital letters
33
10.Change the port settings. 11. Connect to the LCD TV by activating the connection button.
12.[Programming]-[Download] Download window will be opened.
setting "115200"
34
13.Select the file which you want to upload. 15.If the Flash has burned successfully, OK message is shown as
below.
click once
click once
16.Turn the AC power off, and turn AC power on.

Return to default automatically.
17.Finish!!
18.Prepare for next model
If you have once write the software to the set, the PC side commu-
nication speed will be set up to 115200.
So before you connect the PC to the next set, please change back
14.Click Flash button and get executed.
this speed to 9600.
(Please refer 4-(i)-2)
19.Software writing time
It takes about 15 minutes to write the all software with above
method.
Please keep the cable connection during the PC and Set having a
communication.
35
3. Install procedure of Storage Media Manager 6. Please select Next button
(Digital unit PCMCIA download tool)
1. Please unzip attached file. StorageMediaManager1.0.1_Setup.zip
2. You make a suitable folder of your PC, and please copy an *.img
file.
(I made a folder of c:\SSS\img as an example.)
3. Please double-click Setup.exe file of unzip files.
7. Please select Next button
4. Setup is started.
Please select Next button.
8. Setup is complete
9. Please Insert the PCMCIA card of changing software in your PC.
NOTE: Please insert a PCMCIA card before starting an application
10.Please choose Program file Storage Media Manager Stor-
age Media Manager files.
5. Please select Yes button 11. A following window appear.
36
12.At first. Please delete current software of PCMCIA. 15.Copy will be Start.
Please select a drive of PCMCIA with a right window. Then a file If a window disappears, COPY is completion.
name is displayed in bottom window.
Please choose a file. And, please push right click and select delete
button.
16.A new file name is displayed by a right bottom window.

Copying is completed.
13.Please select Yes button

Deletion will be complete.
17.Please finish an application
14.You will copy a new *.img file to PCMCIA card.

You choose a new *.img file with a window of the middle, and
please do drag & drop to a right window.
37
4. Entering and exiting the adjustment process mode
1. Press the POWER key on the set of running TV set to force off the power.
2. While holding down the VOL (-) and MENU keys on the set at once, press the POWER key on the set to turn on the power.
The letter K appears on the screen.
3. Next, hold down the VOL (-) and P ( ) keys on the set at once.
Multiple lines of orange characters appearing on the screen indicate that the set is now in the adjustment Process mode. If you fail to enter the
adjustment process mode (the display is the same as normal startup), retry the procedure.
(Another procedure)
2. Press the MENU key on the main unit to display OSD.
3. Move the cursor to SERVICE (OSD) using the cursor keys on the remote control.
Then press the MENU key on the remote control to enter the service mode (adjustment process mode).
4. To exit the adjustment process mode after the adjustment is done, unplug the AC power cord to force off the power. (When the power is turned off
with the remote controller, once unplug the AC power cord and plug it in again. In this case, wait 10 seconds or so before plugging.)
5. To remove K mode, just repeat step1 and 2. This time the letter K disappears from screen.
Caution: Use due care in handling the information described here lest the users should know how to enter the adjustment process
mode. If the settings are tampered with in this mode, unrecoverable system damage may result.
5. Remote controller key operation and description of display in adjustment process mode.
1. key operation
Remote controller key Main unit key Function

P( / ) P( / ) Changing a selected line setting (+10/-10)
VOL (+/-) VOL (+/-) Turning a page (PREVIOUS/NEXT)
Cursor (UP/DOWN) Moving an item (line) by one (UP/DOWN)
Cursor (LEFT/RIGHT) Turning a page (PREVIOUS/NEXT)
Changing a selected item setting (+1/-1)
MENU Direct control on TV set
(Input/Wide Mode/Bright/Contrast)
INPUT SOURCE on Input source switching (toggle switching)
remote controller (TVEXT1EXT2EXT3EXT4EXT5EXT6)
RETURN Returning to a present page
OK Executing a function
* Input mode is switched automatically when relevant adjustment is started so far as the necessary input signal is available.
2. Description of display
(1) Current page title
[INIT] [PAL+TUNERMAIN] [COMP] [SCART RGB] [TUNER]
Main Version 46.52XL1 1.XX (XX/XX/XXX)

Dev Version XX
Dev Loader Version XX (2) Parameters
Center Acutime XX
Backlight Acutime XX
Temp Sensor XX
Normal Standby Cause XX
Error Standby Cause [1] XX
[5]
(3) Current page item
38
6. Adjustment process mode menu
The character string in brackets [ ] will appear as a page title in the adjustment process menu header.
Page Line Item Description Remarks (adjustment detail, etc.)

1/13 [INFO]
1 Main Version 46/52XL1 ver1.15 2007.0525 Main microprocessor version
2 Dev Version ver1.10 DTV version.
3 Dev Loader Version 2.3 DTV Loader Version
4 Center Acutime xxxxH xxM Main operating hours
5 Backlight Acutime xxxxH xxM Backlight operating hours
6 Temp Sensor 080 Temp Sensor setting
7 Normal Standby Cause 1 RC_STANDBY
8 Error Standby Cause [1] 1a POWER ERROR 0000H 00M Error standby cause Total operating time before error
[2] 0 0000H 00M
[3] 0 0000H 00M
[4] 0 0000H 00M
[5] 0 0000H 00M
2/13 [INIT]
1 FACTORY INIT EURO/RUSSIA/SWEDEN Initialization to factory settings execution
2 INCH SETTING 46/52 Inch Setting
3 PUBLIC MODE off/on HOTEL MODE flag setting
4 Center Acutime Reset off/on Main operating hours Reset
5 Backlight Acutime Reset off/on Backlight operating hours Reset
6 Picture Read Pos X 670 x-axis setting of picture data
7 Picture Read Pos Y 419 y-axis setting of picture data
8 Picture Read Signal Type PAL/COMP/HDMI/RGB Signal Type Setting
9 Picture Read 0-1023 Start/stop of picture data
3/13 [PAL+TUNERMAIN]
1 RF-AGC BG ADJ ENTER RF-AGC BG adjustment execution
2 RF-AGC L ADJ ENTER RF-AGC L adjustment execution
3 PAL+TUNER ADJ ENTER PAL TUNER auto adjustment execution
4 PAL ADJ ENTER PAL auto adjustment execution
5 TUNER ADJ ENTER TUNER auto adjustment execution
6 PAL DAC 29 PAL DAC adjustment
7 TUNER A DAC 29 Tuner DAC adjustment
8 Tuner AGC BG 5 Tuner AGC BG adjustment
9 Tuner AGC L 8 Tuner AGC L adjustment
10 Tuner AGC int. off 6 Tuner AGC gain adjustment
4/13 [COMP]
1 COMP ALL ADJ ENTER COMP15K auto adjustment execution
2 COMP CONTRAST 32 COMP contrast adjustment execution
3 COMP Cb GAIN 32 COMP Cb gain adjustment execution
4 COMP Cr GAIN 32 COMP Cr gain adjustment execution
5 COMP BRIGHT 0 COMP bright adjustment execution
5/13 [SCART RGB]
1 SCART RGB CONTRAST 40 SCART RGB contrast adjustment execution
2 SCART RGB Cb GAIN 40 SCART RGB Cb gain adjustment execution
3 SCART RGB Cr GAIN 40 SCART RGB Cr gain adjustment execution
4 SCART RGB BRIGHT 0 SCART RGB bright adjustment execution
6/13 [TUNER]
1 TUNER TEST
7/13 [M GAMMA INFO]

1 M GAMMA POS 1 4 W/B adjustment, gradation 1 input setting
7 M GAMMA WRITE off/on EEP writing of adjustment values
8 M GAMMA RESET off/on Initialization of adjustment values
39
Page Line Item Description Remarks (adjustment detail, etc.)

8/13 [M GAMMA 1-3]
1 M GAMMA R 1 107 W/B adjustment, gradation 1R adjustment value
2 M GAMMA G 1 107 W/B adjustment, gradation 1G adjustment value
3 M GAMMA B 1 107 W/B adjustment, gradation 1B adjustment value
9/13 [M GAMMA 4-6]
10/13 [ETC]
1 EEP CLEAR off/on Clear of process adjustment EEP value
2 EEP CLEAR B off/on Clear of process adjustment value of B_mode.
3 STANDBYCAUSE RESET off/on Reset of STANDBY CAUSE
4 AUTO INSTALLATION SW 0/1 1: * * * 0: * * *
5 OPTION 0/1
6 COUNTRY Destination setting
7 L ERR RESET 0 LAMP ERR RESET Initialization of L_ERR
8 L ERR STOP 0/1 LAMP ERR Inhibit L_ERR detection.
9 DTV CLR off/on Clear of DTV unit.
10 I2C-OFF off/on STOP of I2C DATA execution
11/13 [LCD]
1 OSC FREQ50 1279 INVERTER drive frequency setting
2 OSC FREQ60 1279 NVERTER drive frequency setting
3 PWM FREQ50 218 Frequency setting for INVERTER dimmer
4 PWM FREQ60 218 Frequency setting for INVERTER dimmer
5 VCOM ADJ 64 COMMON VIAS adjustment setting
6 QS off/on on/off of Quick Shoot Function
7 CSI off/on on/off of Change Shear Impulse
12/13 [LCD TESTPATTERN]
1 PATTERN 0 Display LCD test pattern.
13/13 Service B
1 [HDTV] 0-10 Contrast, Bright and Color Adjustment of HDTV
2 [SERVICE B2] off/on on/off of Auto Sw Adjustment
3 [BASE GAMMA 1] 0-1023 Base Gamma Adjustment 1
9 [QUICK SHOOT] 0-255 QS Sreshuhorld Level Adjustment
3 10
7. Special features
* ERROR STANDBY CAUSE (Page 1/13)
The total time when the unit enters the standby due to operational error and cause of error are recorded on EEPROM as much as possible.
The values can be used to locate the fault for repair.
* EEP CLEAR (Page10/13)
Clear of process adjustment EEP value.
8. Inch Setting
Adjustment point Adjustment Conditions Adjustment procedure

1 Factory settings ends by turning off the MAIN Enter the adjustment process mode.
POWER key. Move the cursor to [INCH SETTING] on page 2/13.
Use the R/C key to select a inch size from [46/52] and press the [OK] key.
EXECUTING display appears.
After a while, OK display appears, the setting is completed.
9. Video signal adjustment procedure * The adjustment process mode menu is listed in Section 5.
1. Signal check
Signal generator level adjustment check (Adjustment to the specified level)
Composite signal PAL: 0.7Vp-p 0.02Vp-p (Pedestal to white level)
15K component signal: Y level 0.7Vp-p 0.02Vp-p (Pedestal to white level)
(50 Hz) PB, PR level 0.7Vp-p 0.02Vp-p
2. Entering the adjustment process mode

Enter the adjustment process mode according to Section 3.
3. RF AGC adjustment 1

1 Setting [Signal] Feed the PAL Split Field colour bar signal (E-12ch) to TUNER.
PAL Signal level: 55 dB V 1dB (75 LOAD)
Split Field Colour Bar
RF signal UV [E-12CH]
[Terminal]
TUNER
100% white
2 Auto adjustment performance Adjustment process Bring the cursor on [RF AGC BG ADJ] and press [OK]
[PAL+TUNERMAIN] menu [RF AGC BG ADJ OK] appears when finished.
3 11
4. Tuner adjustment

1 Setting [Signal] Feed the RF signal (PAL colour bar) to TUNER.
Make sure the PAL colour bar pattern (E-12) has the sync level of 7.3
PAL RF signal with the picture level.
[Terminal] [E-12CH]
TUNER
100% white
2 Auto adjustment performance Adjustment process Bring the cursor on [PAL+TUNER ADJ] and press [OK].
[PAL+TUNERMAIN] menu [PAL+TUNER ADJ OK] appears when finished.
10. White Balance Adjustment

Adjustment gradation values (IN) appear on page 7/13 of process adjustment, and adjustment initial values (offset value) appear on pages 8/13 and
9/13.
For white balance adjustment, adjust the offset values on pages 8/13 and 9/13.
[Condition of the unit for inspection]

Modulated light: MAX (+8)
[Adjustment reference device]

Minolta CA-210
[Adjustment]
Check that the values on page 7/13 of process adjustment are set as below. If not, change them accordingly.
MGAMMA POS 1 4
MGAMMA POS 2 10
MGAMMA POS 3 15
MGAMMA POS 4 19
MGAMMA POS 5 24
MGAMMA POS 6 29
1) Display the current adjustment status at point 6. (Page 8/13 of process adjustment)
The display for checking the adjustment status is toggled by pressing the 6 button on the remote control.
(Normal OSD display 6 display for check (OSD disappears) 6 normal OSD display . . . )
2) Read the value of the luminance meter. x=0.272, y =0.277
3) Change MGAMMA R6/MGAMMA B6 (Adjustment offset value) on page 9/13 of process adjustment so that the values of the luminance meter
approach x=0.272 and y =0.277.
(Basically, G is not changed. If adjustment fails with R and B, change G. When G is lowered, the weaker of R and B must be fixed.)
4) Display the adjustment status of the current point 5. (Each time the 5 button on the remote control is pressed, the adjustment status check dis-
play is toggled.)
(Normal OSD display 5 Check display (OSD disappears) 5 Normal OSD display . . . )
Change M GAMMA R5/M GAMMA B5 (adjustment offset value) on page 9/13 of process adjustment so that the values of the luminance meter
approach x = 0.272 and y = 0.277.
5) Repeat step 4) for points 4, 3, 2, and 1.
[Adjustment reference standard value]
Adjustment spec 0.004 Inspection spec 0.006 (point 1)
Adjustment spec 0.002 Inspection spec 0.004 (Excluding the above-mentioned)
3 12
11. Confirmation item
1. 100Hz Confirmation (Demo Mode Function)
Confirmation item Confirmation method

1 Setting Input a horizontal scroll signal of the vertical bar into the external input.
It moves at a constant speed.
white
2 Confirmation Confirmed that brightness darkens when the DEMO mode is turned on with the DEMO key to remote control
and the afterimage decreases.
2. Magi-Link Inspection
The thing that the Magi-Link circuit operates is confirmed.
3. HDMI-CEC Inspection
The thing that the HDMI-CEC circuit operates is confirmed.
12. Initialization to factory settings
Caution: When the factory settings have been made, all user setting data, including the channel settings, are initialized. (The adjustments done in
the adjustment process mode are not initialized.) Keep this in mind when initializing these settings.
Adjustment item Adjustment conditions Adjustment procedure

1 Factory settings ends by turning off the MAIN POWER [Factory setting with adjustment process mode]
key. Enter the adjustment process mode.
(See to below caution) Move the cursor to [Factory Init] on page 2/13.
Use the R/C key to select a region from [EURO/UK/ITALY/FRANCE/
RUSSIA] and press the [OK] key.
EXECUTING display appears.
[Factory setting with R/C key]
Enter the adjustment process mode.
Push a remote controller code of each destination. (See below)
It automatically becomes in the process adjustment menu (INIT) and change
FACTORY INIT becomes EXECUTING display.
destination R/C code

46/52XL1R EB (Hex)
46/52XL1S EC (Hex)
46/52XL1E FE (Hex)
The following items are initialized in the factory setting.

1) User settings
2) Channel data (e.g. broadcast frequencies)
3) Maker option setting
4) Password data
After adjustments, exit the adjustment process mode.

To exit the adjustment process mode, turn off the MAIN power key.
When the power is turned off with the remote control, unplug the AC power cord and plug it back in.
3 13
13. Lamp error detection
1. Function
This LCD color TV set incorporates a lamp error detection feature that automatically turns off the power for safety under abnormal lamp or lamp
circuit conditions. If by any chance anything is wrong with the lamp or lamp circuit or if the lamp error detection feature is activated for some rea-
son, the following will result.
1) The power is interrupted in about 6 seconds after it is turned on.
(The power LED on the front of the TV set turns red from green and keeps blinking in red: ON for 250 ms and OFF for 1 sec.).
2) If the above phenomenon 1) occurs 5 times consecutively, it becomes impossible to turn on the power. (The power LED remained red).
2. Measures
1) Checking with lamp error detection OFF
Enter the adjustment process mode, referring to 3. Entering and exiting the adjustment process mode.
If there is a problem with the lamp or lamp circuit, the lamp will go out. (The power LED is green.)
Then, you can check the operation to see if the lamp and lamp circuit are in trouble.
2) Resetting the lamp error count
After the lamp and lamp circuit are found out of trouble, reset the lamp error count. If a lamp error is detected five consecutive times, the power
cannot be turned on. Using the cursor (UP/DOWN) key, move to the cursor to [L ERR RESET], Line 7 on adjustment process mode service
page 10/13. With the cursor (LEFT/RIGHT) keys, select the [L ERR RESET] value. Finally press the cursor (OK) eys to reset the value to 0.
Table of contents of adjustment process mode Page 10/13
[ETC]
EEP CLEAR off
EEP CLEAR B off
STANDBYCAUSE RESET off
AUTO INSTALLATION SW 0
OPTION 0
COUNTRY EURO
L ERR RESET 0 Resetting to "0"
L ERR STOP 0
DTV CLR off
I2C-OFF off
3 14
14. Public Mode
1. How to enter Public mode
Enter the adjustment process mode, referring to 3. Entering and exiting the adjustment process mode.
In the [INIT], page2/13 of service, turns on the PUBLIC MODE option.
Turn off TV by pressing Power button of TV unit.
Press Power button of TV unit and then press V- of RC and V- of TV at the same time during the switch-on action (before the screen is dis-
played)
NOTE:
Language: English only
Options Monitor, Basic, Hotel, Full

Default Full
Chart of available parameters in each mode
Monitor Basic Hotel Full

Power on fixed x
Maximum volume x x x
Volume fixed x
Fixed volume level x
Input mode start x x x
Input fixed x
Start-up preset x x x
Reset x x x
In possible to select each item of function by press cursor UP/DOWN keys on remote control.
The setting position of each item of function is made by press cursor RIGHT/LEFT keys on remote control.
Press OK key on remote control for confirmation after you set all functions.
2. Valid/Invalid function table
In ATV mode In DTV mode

(R/C)KEY_CODE MONITOR BASIC HOTEL MONITOR BASIC HOTEL
Power *1 x x *1 x x
TELETEXT x x
1-9,0 x x
FLASH_BACK x x
Input select *2 x x *2 x x
DTV x *2 x x
EPG,ESG
RADIO *2 x x
SOUND(MPX) x x x x
mute x x
V+,V- *3 x x *3 x x
P+,P- *2 x x *2 x x
AV mode x x Standard setting called
Surround
LIST x
i+ x x
DTV menu
Menu
OK (Station/Program List) x x
truD
SLEEP x x
Wide mode x x
OPC
(TV unit) KEY_CODE MONITOR BASIC HOTEL MONITOR BASIC HOTEL

Menu *2 x x *2 x x To select input only
P+,P- *2 x x x x x
V+,V- *3 x x *3 x x
*1: The key is available in a case that Power on fixed is set to no.
*2: The key is available in a case that Input fixed is set to no.
*3: The key is available in a case that Volume fixed is set to no.
3 15
Full mode: Normal operation, no restrictions
3. Parameter setting
1) POWER ON FIXED
Options yes, no
Default no
2) MAXIMUM VOLUME
Options 0 --- 63
Default 63
3) VOLUME FIXED
Options yes, no
Default no
4) VOLUME FIXED LEVEL
Options 0 --- Maximum volume

Default 20
5) INPUT MODE START
Options normal, TV, DTV, EXT1, EXT2, EXT3, EXT4, EXT5, EXT6
Default normal
6) INPUT MODE FIXED
Options yes, no
Default no
7) START-UP PRESET
Options 0 --- maximum preset channel

Default 0001
8) RESET
Options execute, no
Default no
3 16
CHAPTER 4. TROUBLESHOOTING TABLE
LC46XL1E
Service Manual
[1] TROUBLESHOOTING TABLE

Power switched on but no power supplied.
Are the power cord and internal harnesses correctly con- NO Reconnect the cables correctly and switch on the power again.
nected?
YES
Does F701 function? NO Replace F701 and switch on the power again. Does the fuse blow
out?
YES NO
Is there a voltage of about 5V at the BU5V output [between pins (20) (+) and (22) (-) of PA]?
NO
YES
Replace R790, D742, NO Is the voltage at C790
IC702, R780 and R781. higher than 8V?
YES YES
Are there voltages of about 13V, 24V and 35V at the UR13V, NO Check D708, Q727, Q726, Replace Q705, D715,
S29V and UR35V outputs, respectively? R830, R829, D762, D763, IC701, R726 and R721.
Q741, R824, R825, IC704,
R826, R827 and R828.
YES
Is the relay activated clicking? NO Check Q706, Q741, D707, D729 and R776.
YES
Is there a voltage of about 12V at UR12V [between pins (1) NO Check Q731, Q742, Q732, D767, D766, R843, R844 and C799.
(+) and (3) (-) of PL]?
YES
Is there a voltage of about 380V at C726? NO Check Q705, D715, IC701, R726 and R721.
YES
Is there a voltage of about 60V at the INV60V output NO Check Z1, Q707, Q708, Q716 and L706.
[between pins (1) (+) and (3) (-) of LA]?
YES
Is there a voltage of about 10V at the INV10V output NO Check IC705, R832, R833, R834 and C813.
[between pins (5) (+) and (3) (-) of LA]?
41
No sound (1) (during the reception of TV broadcasting)
No audio output during UHF/VHF reception
Checklist:
1) Is the volume set to MIN or MUTE on the remote control? ... Set the desired volume.
2) Are headphones connected to HEADPHONE (J1301)? ... Disconnect them.
3) Is ANT-CABLE disconnected or connected improperly? ... Connect it correctly as per the operation manual.
Is the audio signal (L/R) Is the SIF signal YES Check whether +5V and
sent from pins (28) and NO (ANA_IN1+) sent to pin +8V are supplied to pins
(27) of IC3701 (MSP)? (67) of IC3701 (MSP)? (12) and (39) of IC3701
respectively. Or, check
peripheral circuits.
(AV-UNIT) YES NO
Is the audio signal of pins NO Check SC2704 and P1201 Is the audio signal (SIF) YES Check pin (67) of IC3701
(3) and (5) of IC303 (OP- or peripheral circuits. sent from pin (1) of CON- (MSP) and peripheral cir-
AMP) sent properly? Is the S-MUTE signal L? NECTOR (SC2705)? cuits.
YES (TUNER) NO
Is the audio signal of pin NO Check HEAD-PHONE Is the audio signal (SIF) YES Check CONNECTOR
(4) of IC301/IC302 (J1301) or peripheral sent from pin (12) of IC201 (P201) and peripheral cir-
(AUDIO-AMP) sent prop- circuits. (IF-DEMOD)? cuits.
erly?
YES NO
Is the audio signal output NO Check P301 (AUDIO- Is the SIF signal sent to YES Confirm whether +5V is
of pins (2) and (4) of P301 CONNECTOR) and pins (23) and (24) of supplied to IC201.
(AUDIO-CONNECTOR) peripheral circuits. IC201 (IF-DEMOD)? Or, please check the
normal? peripheral circuit.
YES NO
Check SP-BOX (right and Is the IF signal sent from YES Check soldering the termi-
left) and wire harness. pin (17) of TUNER nal and peripheral circuits.
(TU201)?
NO
Check whether 5V YES Replace TUNER (TU201).
(CONT) and 5V are sup-
plied to pins (1) and (2) of
TUNER (TU201) respec-
tively.
Check SDA/SCL and AGC
signal.
42
No sound from external input devices (2) -1
No sound from an external input No sound from an external No sound from an external
device connected to EXT1 input device connected to input device connected to
(SCART1). EXT2 (SCART2). EXT3.
<EXT1> <EXT2> <EXT3>

Is IN1-L audio signal sent from Is IN2-L audio signal sent Is IN3-L audio signal sent from
pin (6) of SCART1 terminal YES from pin (27) of SCART2 ter- YES pin (3) of J1201 terminal to pin
(J1101) to pin (53) of IC3701 minal (J1101) to pin (56) of (47) of IC3701?
(MSP)? IC3701 (MSP)? Is IN3-R audio signal sent from
Is IN1-R audio signal sent from Is IN2-R audio signal sent pin (5) of J1201 terminal to pin
pin (2) of SCART1 terminal from pin (23) of SCART2 ter- (48) of IC3701?
(J1101) to pin (54) of IC3701 minal (J1101) to pin (57) of
(MSP)? IC3701 (MSP)?
NO NO NO
Check pins (6) and (2) of Check pins (27) and (23) of Check pins (3) and (5) of EXT3
SCART1 and connection to an SCART2 and connection to (J1201) and connection to an
external input device. an external input device. external input device.
Is the audio signal properly sent from pins (28) and (27) of IC3701?
NO YES
Check IC3701 or peripheral circuits. Is the audio signal of pins (1) NO Check IC303 or peripheral circuits.
and (7) of IC303 (OP-AMP)
sent properly?
YES
Is the audio output signal of NO Check IC302/IC301 (MAIN-AMP),
pins (13) and (16) of IC302/ HEADPHONE and peripheral circuits.
IC301 (MAIN-AMP) normal?
YES
Check CONNECTOR (P301)
and SP-BOX (right and left).
43
No sound from external input devices (2) -2
No sound from EXT4 (AUDIO) connect- No sound from EXT5 (AUDIO) connect-
ing an external input device. ing an external input device.
<EXT4> <EXT5>
Is D-SUB-L audio signal sent from J2702 Is HDMI-L audio signal sent from J2701
to pin (15) of IC2704? to pin (14) of IC2704?
Is D-SUB-R audio signal sent from J2702 Is HDMI-R audio signal sent from J2701
to pin (2) of IC2704? to pin (5) of IC2704?
YES YES
Is D-SUB-L audio signal sent to pin (50) Is HDMI-L audio signal sent to pin (50) of NO Check output of pins (13) and (3) of
of IC3701? IC3701? IC2704 and peripheral circuits.
Is D-SUB-R audio signal sent to pin (51) Is HDMI-R audio signal sent to pin (51) of
of IC3701? IC3701?
YES YES
Is the audio signal properly sent from pins (28) and (27) of IC3701? NO Check IC3701 or peripheral circuits.
YES
Is the audio signal of pins (1) and (7) of NO Check IC303 or peripheral circuits.
IC303 (OP-AMP) sent properly?
YES
Is the audio output signal of pins (13) and NO Check IC302/IC301 (MAIN-AMP),
(16) of IC302/IC301 (MAIN-AMP) nor- HEADPHONE and peripheral circuits.
mal?
YES
Check CONNECTOR(P301) and
SP-BOX (right and left).
44
No sound except from speakers (3) -1
No audio output from the No audio output from

headphones. EXT1 (SCART1) terminal.
Is there audio output on pins Checklist:

(2) and (3) of the headphone 1) Is the MUTE button on the remote control set to ON? ... Set to OFF.
terminal (J1301)? 2) Check the connection to external devices. ... Is there any improper connection?
NO
Is audio input/output signal of Is audio signal sent to pins NO Is S-MUTE-LINE
pins (3) and (5)/(1) and (7) of (3) and (1) of EXT1 [IC1710 (pin 92)] at H?
IC303 (OP-AMP) normal? (J1101)? (Check Q1106/Q1105
operation.)
NO YES NO
Is audio output signal (SPK- Check the connection to Is audio signal sent NO Check the power supply
OUT L/R) properly sent from EXT1 (J1101) and exter- from pins (33) and (34) 8/5 V pins (39) and (12)
pins (28) and (27) of IC3701 nal devices. of IC3701? of IC3701 and periph-
(MSP)? eral circuits.
NO YES
Check audio input signal of pin Check the audio signal
(67) of IC3701(MSP), pins output line from pins
(39) and (12) of the power (33) and (34) of IC3701
line5 and 8V, pins (3) and (2) to pins (3) and (1) of
of I2C-LINE, and peripheral EXT1.
circuits.
No sound except from speakers (3) -2
Is S-MUTE-LINE [IC1710 (pin 92)] at H?

No audio output from No audio output from
EXT2 (SCART2) termi- AUDIO OUTPUT termi-
nal. nal.
Checklist:
1) Is the MUTE button on the remote control set to ON? ... Set to OFF.
2) Check the connection to external devices....Is there any improper connection?
Is audio signal sent to NO Is S-MUTE-LINE [IC1710 Is S-MUTE-LINE NO Is audio signal sent to

pins (24) and (22) of (pin 92)] or S2-MUTE- [IC1710 (pin 92)] at H? pins (13) and (15) [L/R
EXT2 (J1101)? LINE [IC1710 (pin 90)] at (Check 1204/Q1203 (white) (red)] of AUDIO
H? operation.) OUTPUT terminal
(Check Q1102/Q1101 (J1201)?
operation.)
YES NO NO YES
Check the connection to Is audio signal sent from pins (36) and (37) of IC3701? Check the connection
EXT2 (J1101) and to AUDIO OUTPUT
external devices. terminal (J1201) and
external devices.
NO YES
Check the power supply 8/ Check the audio signal
5 V pins (39) and (12) of output line from pins
IC3701 and peripheral cir- (36) and (37) of IC3701
cuits. to Q1103/Q1104/
Q1201/Q1202.
45
DTV troubleshooting 1
The unit does not enter YES Go to The unit does not The unit does not enter the DTV mode. Or, the DTV menu does not
the DTV mode. Or, the enter the DTV mode. Or, appear.
DTV menu does not the DTV menu does not
appear. appear.
NO
No video output during YES Go to No video output Digital UNIT: NO Check peripheral circuits
DTV reception. during DTV reception. Is a voltage supplied from of IC4701/IC4704 and pin
IC4701 (3.3V-REG)/ (7) of IC4701.
IC4704 (1.8V-REG)?
NO YES
No audio output during YES Go to No audio output Do X4001/X4002 oscil- NO Check peripheral circuits
DTV reception. during DTV reception. late? of X4001/X4002.
YES
D-TUNER UNIT: NO Check peripheral circuits
Is a voltage of 1.8/3.3V of IC205/IC206.
supplied from IC205
(REG) and IC206 (REG)?
YES
Is a voltage applied to NO MAIN UNIT:
pin(20) (I2CSEL) of P202? Check around the pin (85)
(High=3.3V) of IC1710 (FPGA).
YES
Is FESDA/FESCL signal NO Check peripheral circuits
sent to pins (21) and (22) of IC202 (COFDM)/
of P202 and pins (21) and IC4001 (D-Processor).
(20) of IC202 (COFDM).
YES
Does X-TAL X202 of NO Check peripheral circuits
IC202 oscillate? of X202.
YES
Check IC202(COFDM)/
IC4001 (D-Processor).
46
DTV troubleshooting 2
No video output during DTV reception. Colors of Images are not right. No audio output during DTV reception. Sound is low.
D-TUNER UNIT: NO Check R272 and R273. DIGITAL UNIT: NO Check R4002 (AD2pin)
Is data FED [0:7] sent Is audio signal fed to pins and IC4001 (D-Proces-
from pins (3), (4), (5), (6), (5) and (10) of IC4604 sor).
(8), (9), (10) and (11) of (OP-AMP)?
P202?
YES YES
DIGITAL UNIT: NO Check R4011 (AC8pin), Is audio signal sent from NO Check power supply of
Are video signals (R/G/B, R4013 (AC9pin) and pins (7) and (8) of IC4604 IC4604 (OP-AMP) and its
CVBS) sent from C4639/ IC4001 (D-Processor). (OP-AMP)? peripheral circuits.
C4640/C4641/C4625?
YES YES
Are video signals (R/G/B, NO Check Q4601-Q4605, MAIN UNIT: NO Check power supply and
CVBS) send from the Q4607 and their periph- Is audio signal sent to pin control signal of pins (9)
C4636/C4637/C4638 and eral circuits. (3) and (13) of IC2704 and (10) of IC2704 (SW)
emitters of Q4607? (SW)? and audio signal input of
pins (4) and (11) of
IC2704.
YES YES
MAIN UNIT: Perform the same check
Are video signals (R/G/B, as the tuner (U/V) recep-
CVBS) fed from pins tion.
(AA18), (AB18), (Y18) and
(AA21) of IC3002?
YES
Are scrambled images not YES DIGITAL UNIT:
displayed? Check 5V output of pin (1)
of IC4702.
Check 5V of pin (6) of
Q4401.
NO
Perform the same check
as the tuner (U/V) recep-
tion.
47
<On input of the tuner (U/V)> No picture on the display (1)
No picture appears on LCD during the tuner (U/V) reception.
Checklist:
1) Is INPUT SOURCE button on the remote control set up correctly? ... See the operation manual and set INPUT SOURCE to TV.
2) Is MENU-Picture-Contrast/Brightness set to MIN? ... Set it to an appropriate level.
3) Is ANT-CABLE disconnected or connected improperly? ...Connect it correctly as per the operation manual.
YES
Is level of pins (15) and (14) of tuner (TU201) and pins (12) and NO These are communications lines for control (I2C). Follow the path
(2) of IC204 (MULTI) at H? and check whether they are forced to L (PULL_DOWN).
YES
Is the video signal (IF) sent from pin (17) of tuner (TU201)? NO Check the tuner (TU201) and peripheral circuits.
YES
Is the video signal CVBS sent to pin (AC23) of lC3002 (V-PRO.)? NO Check CONNECTOR (P201/SC2705) and peripheral circuits.
YES
Is LVDS video signal (TA1~TE1) sent to pins (AB8)/(AC8) - NO Check pins (G14)/(U10) of BU3.3V line of IC3002 (V-PRO.), pins
(AB3)/(AC3) of IC3002 (V-PRO.), and is CLK signal (CK1) sent (G10)/(N17) of BU2.5V line, pins (U16)/(G12) of BU1.8V line and
to pins (AB5)/(AC5)? peripheral circuits.
Is LVDS video signal (TA2~TE2) sent to pins (AC2)/(AC1) -
(V2)/(V1) of IC3002 (V-PRO.), and is CLK signal (CK2) sent to
pins (Y2)/(Y1)?
YES
Check the FRC- circuit.
Refer to sheet of FRC (100Hz). (P4-20)
YES
Is LVDS video signal (TA1~TE1) sent to pins (3)/(2) - (18)/(17) NO Check CONNECTOR (SC6211, CN1) and HARNESS WIRE
of CONNECTOR CN1 of LCD-CONT-UNIT, and is CLK signal (LV).
(CK1) sent to pins (12)/(11)?
Is LVDS video signal (TA2~TE2) sent to pins (21)/(20) - (36)/
(35) of CONNECTOR CN2 of LCD-CONT-UNIT, and is CLK sig-
nal (CK2) sent to pins (30)/(29)?
YES
Is power (+12V) supplied to pins (1) - (5) of CONNECTOR CN3 NO Check CONNECTOR (CN3, PL) and HARNESS WIRE (PL).
in LCD-CONT-UNIT?
YES
Replace LCD-CONT-UNIT.
48
<During external connection> No picture on the monitor (2) -1
SCART1: SCART2:
No picture appears on EXT1 -connected monitor during the tuner (U/V) No picture from EXT1 appears on EXT2-connected monitor.
reception.
NOTE: Normally, if the screen during display is sent to EXT2, no pic-
ture is sent to EXT2.
Checklist:
1) Are input terminal on back of TV and INPUT SOURCE button on the remote control set up correctly? ... See the operation manual and
set INPUT SOURCE appropriately.
2) Is the Signal Type (item) in MENU-Connection-Input-Select set to the same as that of the external device? ... Set it to CVBS, Y/C or RGB.
4) The picture is sent to the monitor in a CVBS signal if the source during display is TV, CVBS or Y/C of EXT1-3. When sent by component, etc.,
that signal is not sent to the monitor.
5) When the monitor picture is not sent and is not displayed on the monitor, refer to No picture for each terminal.
6) The video output from EXT1 is not the monitor output (output of the picture now watching). The picture of the last selected TV channel is always
sent to EXT1. (Specification).
Is video signal sent to YES Check SCART1, external Is video signal sent to YES Check SCART2, external
pin (19) of SCART1 connection or input setting. pin (40) of SCART2 connection or input setting.
(J1101)? (J1101)?
NO NO
Is video signal (V- YES Check SCART1 (J1101) and Is video signal (V- YES Check SCART2 (J1101) and
OUT1) sent from pin (2) peripheral circuits. OUT2) sent from pin (2) peripheral circuits.
of IC1102 (SW)? of IC1101 (SW)?
NO NO
Is video signal (V- YES Check IC1102 (SW), Is video signal (V- YES Check IC1101 (SW),
OUT1) sent from pin Connector (P1101, SC2702) OUT2) sent from pin Connector (P1102, SC2703)
(Y23) of IC3002 (V- and peripheral circuits. (Y20) of IC3002 (V- and peripheral circuits.
PRO.)? PRO.)?
NO NO
Is video signal (CVBS) YES Check power supply of Is video signal (VIN1) YES Check power supply of
sent to pin (AC23) of IC3002 (V-PRO.) and periph- from EXT1 sent to pin IC3002 (V-PRO.) and periph-
lC3002 (V-PRO.)? eral circuits. (AB22) of IC3002 (V- eral circuits.
PRO.)?
NO NO
Is video signal (IF) sent YES Check CONNECTOR (P201, Check whether video YES Check SCART1, CONNEC-
from pin (11) of tuner SC2705) and peripheral cir- signal is sent to pin (20) TOR (SC2702, P1101) and
(TU201)? cuits. of SCART1. peripheral circuits.
NO NO
Check 5/33 V power Check SCART1, exter-
supply pins (10) and (7), nal connection or input
I2C line pins (9) and (8) setting.
of tuner (TU201) and
49
<During external connection> No picture on the monitor (2) -2
SCART2:
No picture from EXT3 appears on EXT2- connected monitor.
Checklist:
1) Are input terminal on back of TV and INPUT SOURCE button on the remote control set up correctly? ... See the operation manual and
set INPUT SOURCE appropriately.
2) Is the Signal Type (item) in MENU-Connection-Input-Select set to the same as that of the external device? ... Set it to CVBS, Y/C or RGB.
4) The picture is sent to the monitor in a CVBS signal if the source during display is TV, CVBS or Y/C of EXT1-3. When sent by component, etc.,
that signal is not sent to the monitor.
5) When the monitor picture is not sent and is not displayed on the monitor, refer to No picture for each terminal.
6) The video output from EXT1 is not the monitor output (output of the picture now watching). The picture of the last selected TV channel is always
sent to EXT1. (Specification).
Is video signal sent to pin (40) of SCART2 (J1101)? YES Check SCART2, external connection or input setting.
NO
Is video signal (V- OUT2) sent from pin (2) of IC1101 (SW)? YES Check SCART2 (J1101) and peripheral circuits.
NO
Is video signal (V- OUT2) sent from pin (Y20) of IC3002 YES Check IC1101 (SW), Connector (P1102, SC2703) and periph-
(V-PRO.) ? eral circuits.
NO
Is video signal (IN3Y) from EXT3 sent to pin (AB20) of IC3002 (V- YES Check power supply of IC3002 (V-PRO.) and peripheral circuits.
PRO.)?
NO
Is video signal (IN3YV) sent to pin (2) of IC1201 (SW)? YES Check pin (AB20) of IC3002 (V-PRO.), CONNECTOR (SC2703,
P1102) and peripheral circuits.
NO
Is video signal (CVBS) sent from pin(1) of A/V-TERMINAL YES Check pin (1) (IN3SW) of IC1201 (SW), power supply and
(J1201=EXT3)? peripheral circuits.
NO
Check A/V-TERMINAL (J1201), external connection or input set-
ting.
4 10
<When EXT1 is used for external input> No picture on the display (3)-1
No EXT1 -Composite output of the external input system. No EXT1-RGB output of the external input system.
Checklist:
1) Is INPUT SOURCE button on the remote control set up correctly? ... See the operation manual and set INPUT SOURCE to EXT1.
2) Is MENU-Picture-Backlight/Contrast/Brightness set to MIN? ... Set it to an appropriate level.
3) Check the connection to the external device ... Connect it correctly as per the operation manual for the device.
Is composite video signal NO Check external connec- Is RGB signal sent to pins NO Check external connection,
sent to pin (20) of tion, input setting, (15), (11) and (7) of input setting, SCART1
SCART1 (J1101)? SCART1 and peripheral SCART1 (J1101)? (J1101) and peripheral cir-
circuits. cuits.
YES YES
Is composite video signal NO Check CONNECTOR Is RGB signal (RED1/ NO Check CONNECTOR
(VIN1 (V)) sent to input (SC2702/P1101), GREEN1/BLUE1) sent to (SC2702/P1101), SCART1
terminal pin (AB22) of SCART1 (J1101) and input terminal pins (Y19) (J1101) and peripheral cir-
IC3002 (V-PRO.)? peripheral circuits. (AB19) and (AC18) of cuits.
IC3002 (V-PRO.)?
YES YES
Is LVDS video signal (TA1~TE1) sent to pins (AB8)/(AC8) - (AB3)/(AC3) of IC3002 (V-PRO.), and is NO Check pins (G14)/(U10) of
CLK signal (CK1) sent to pins (AB5)/(AC5)? BU3.3V line of IC3002 (V-
Is LVDS video signal (TA2~TE2) sent to pins (AC2)/(AC1) - (V2)/(V1) of IC3002 (V-PRO.), and is PRO.), pins (G10)/(N17) of
CLK signal (CK2) sent to pins (Y2)/(Y1)? BU2.5V line, pins (U16)/
(G12) of BU1.8V line and
YES
YES
Is LVDS video signal (TA1~TE1) sent to pins (3)/(2) - (18)/(17) of CONNECTOR CN1 of LCD- NO Check CONNECTOR
CONT-UNIT, and is CLK signal (CK1) sent to pins (12)/(11)? (SC6211, CN1) and HAR-
Is LVDS video signal (TA2~TE2) sent to pins (21)/(20) - (36)/(35) of CONNECTOR CN1 of LCD- NESS WIRE.
CONT-UNIT, and is CLK signal (CK2) sent to pins (30)/(29)?
YES
Is power (+12V) supplied to pins (1) - (5) of CONNECTOR CN3 in LCD-CONT-UNIT? NO Check CONNECTOR (CN3,
PL) and HARNESS WIRE
(PL).
YES
4 11
<When EXT1 is used for external input> No picture on the display (3)-2
No EXT1-Y/C output of the external input system.
Checklist:
Is Y/C signal sent to pins (20) and (15) of SCART1 (J1101)? NO Check external connection, input setting, SCART1 (J1101) and
YES
Is Y/C signal (Y1/C1) sent to input terminal pins (AB22) and (Y19) NO Check CONNECTOR (SC2702/P1101), SCART1 (J1101) and
of IC3002 (V-PRO.)? peripheral circuits.
YES
Is LVDS video signal (TA1~TE1) sent to pins (AB8)/(AC8) - NO Check pins (G14)/(U10) of BU3.3V line of IC3002 (V-PRO.),
(AB3)/(AC3) of IC3002 (V-PRO.), and is CLK signal (CK1) sent pins (G10)/(N17) of BU2.5V line, pins (U16)/(G12) of BU1.8V
to pins (AB5)/(AC5)? line and peripheral circuits.
pins (Y2)/(Y1)?
YES
YES
Is LVDS video signal (TA1~TE1) sent to pins (3)/(2) - (18)/(17) NO Check CONNECTOR (SC6211, CN1) and HARNESS WIRE.
of CONNECTOR CN1 of LCD-CONT-UNIT, and is CLK signal
YES
Is power (+12V) supplied to pins (1) - (5) of CONNECTOR CN3 in NO Check CONNECTOR (CN3, PL) and HARNESS WIRE (PL).
LCD-CONT-UNIT?
YES
4 12
<When EXT2 is used for external input> No picture on the display (4)
No EXT2-Composite output of the external input system. No EXT2-Y/C output of the external input system.
Checklist:
Is composite video signal NO Check external connec- Is Y/C signal sent to pins NO Check external connection,
sent to pin (41) of tion, input setting, (41) and (36) of SCART2 input setting, SCART2
SCART2 (J1101)? SCART2 (J1101) and (J1101)? (J1101) and peripheral
peripheral circuits. circuits.
YES YES
Is composite video signal NO Check CONNECTOR Is Y/C signal (VIN2=Y2/ NO Check CONNECTOR
(VIN2 (V)) sent to input (SC2703/P1102), C2) sent to input terminal (SC2703/P1102), SCART2
terminal pin (AB2) of SCART2 (J1101) and pins (AB2) and (AC21) of (J1101) and peripheral cir-
IC3002 (V-PRO.)? peripheral circuits. IC3002 (V-PRO.)? cuits.
YES YES
YES
YES
YES
(PL).
YES
4 13
No EXT3 composite output of the external input system. No EXT3-Y/C output of the external input system.
Checklist:
Is composite video signal NO Check external connec- Is Y/C signal sent to pins NO Check external connection,
sent to pin (1) of A/V-IN- tion, input setting, A/V- (11) and (7) of S-TERMI- input setting, S-TERMINAL
TERMINAL IN-TERMINAL (J1201) NAL (J1201)? (J1201) and peripheral cir-
(J1201)? and peripheral circuits. cuits.
YES YES
Is composite video signal NO Check A/V-IN-TERMI- Is Y3 signal (IN3-Y) sent NO Check S-TERMINAL
(IN3-CVBS) sent to input NAL (J1201) and periph- to Input terminal pin (6) of (J1201) and peripheral cir-
terminal pin (4) of IC1201 eral circuits. IC1201 (SW)? cuits.
(SW)?
YES YES
Is composite video signal NO Check CONNECTOR Is Y/C signal (IN3Y/IN3C) NO Check CONNECTOR
(IN3 (V)) sent to input ter- (SC2703/P1102), sent to input terminal pins (SC2703/P1102), IC3002
minal pin (AB20) of IC3002 (V-PRO.) and (AB20) and (AC20) of (V-PRO.) and peripheral cir-
IC3002 (V-PRO.)? peripheral circuits. IC3002 (V-PRO.)? cuits.
YES YES
YES
YES
YES
(PL).
YES
4 14
No EXT4 (15pin-D-SUB terminal) output of the external input sys-

tem.
Checklist:
2) Connect the included D-SUB-Adapter-Cable to the COMPONENT terminal of an external device. ... See the operation manual (use a commer-
cially available Component-Cable to connect to the external device).
3) Is ANT-CABLE disconnected or connected improperly? ... Connect it correctly as per the operation manual
NO
Is EXT4 selected with button on the remote control? Select EXT4 with button on the remote control.
YES
Is D-SUB-COMPONENT signal (APC_R/G/B) sent to pins (1), (2) NO Check D-SUB-adaptor and external connection.
and (3) of EXT4-TERMINAL (SC2303)?
YES
Is D-SUB-COMPONENT signal (APC-R/G/B) sent to pins (AA17), NO Check EXT4-TERMINAL and peripheral circuits.
(AB17) and (Y17) of IC3002 (V-PRO.)?
YES
pins (Y2)/(Y1)?
YES
YES
YES
LCD-CONT-UNIT?
YES
4 15
No EXT5 (HDMI) output of the external input system.
Checklist:
2) Have you checked the type video signal sent from HDMI-connected external device? ... Confirm the type (it should RGB, YCbCr 4:4:4 or
YCbCr 4:2:2).
3) Have you checked the type of Color matrix sent from HDMI-connected external device? ... Confirm the type (it should be ITU601 or ITU709.)
4) Is ANT-CABLE disconnected or connected improperly? ... Connect it correctly as per the operation manual
NO
YES
Is the type of video signal (Signal Type) from HDMI- connected NO From MENU-Connections-HDMI setup-EXT5-Signal type, select
external device set? a signal type (RGB, YCbCr 4:4:4 or YCbCr 4:2:2).
YES
Is the type of color signal (Color matrix) from HDMl -connected NO From MENU-Connections-HDMI setup-EXT5-Color Matrix,
external device set? select a color signal type (ITU601 or ITU709).
YES
Is TMDS signal (RX*signal) sent to pins (1) - (12) of EXT5 NO Is I2C signal (SDA/SCL signal) sent to pins (16) and (15) of
(HDMI) terminal (SC1901)? EXT5 (HDMI) terminal? Check external connection and periph-
eral circuits.
YES
Is 8bit-DIGITAL signal (HDMI- R/G/B) sent from pins (110)- (144) NO Check power supply (3.3/1.8V) pins (99) and (74) of IC1905,
of IC1905 (HDMI-RECEIVER)? SDA/SCL signal pins (29) and (30), and peripheral circuits.
YES
Is 8bit-DIGITAL signal (HDMI- R/G/B) sent to pins (B10) - (D15) of NO Check SDA3/SCL3 signal pins (27) and (28), interface between
IC3002 (V-PRO.)? IC1905 and lC3002, and peripheral circuits.
YES
pins (Y2)/(Y1)?
YES
YES
YES
LCD-CONT-UNIT?
YES
4 16
No EXT6 (HDMI) output of the external input system.
Checklist:
2) Have you checked the type video signal sent from HDMI-connected external device? ... Confirm the type (it should RGB, YCbCr 4:4:4 or
YCbCr 4:2:2).
3) Have you checked the type of Color matrix sent from HDMI-connected external device? ... Confirm the type (it should be ITU601 or ITU709.)
NO
YES
Is the type of video signal (Signal Type) from HDMI- connected NO From MENU-Connections-HDMI setup-EXT6-Signal type, select
external device set? a signal type (RGB, YCbCr 4:4:4 or YCbCr 4:2:2).
YES
Is the type of color signal (Color Matrix) from HDMl-connected NO From Connections-HDMI setup-EXT6-Color Matrix, select a
external device set? color signal type (ITU601 or ITU709).
YES
Is TMDS signal (RX*signal) sent to pins (1) - (12) of EXT6 NO Is I2C signal (SDA/SCL signal) sent to pins (16) and (15) of
(HDMI) terminal (SC1902)? EXT6 (HDMI) terminal? Check external connection and periph-
eral circuits.
YES
Is 8bit-DIGITAL signal (HDMI- R/G/B) sent from pins (110) - (144) NO Check power supply (3.3/1.8V) pins (99) and (74) of IC1905,
of IC1905 (HDMI-RECEIVER)? SDA/SCL signal pins (29) and (30), and peripheral circuits.
YES
Is 8bit-DIGITAL signal (HDMI- R/G/B) sent to pins (B10) - (D15) of NO Check SDA3/SCL3 signal pins (27) and (28), interface between
IC3002 (V-PRO.)? IC1905 and lC3002, and peripheral circuits.
YES
pins (Y2)/(Y1)?
YES
YES
YES
LCD-CONT-UNIT?
YES
4 17
FRC (IC3301) circuit failure
NOTE: The SD signal (576i 480i) alone passes through the FRC circuit. (The HD signal does not go through.)
Does the image appear with the HD sig- Does anything unusual (which or black- Does the image look unusual with the
nal, but not with the SD signal? ish screen, block noise, for example) power switch turned on?
appear on the screen?
YES YES YES

Is the power supplied to IC3301 (FRC)? Is there the specified RESET-A signal Check the connection between pin
Is there the FRC-IN signal input at pins input at pin (39) of IC3301(FRC)? (R22) of IC3002 (V-PRO.) and pin
(142) and (13) of IC3301? (60 ms delay design) (142) of IC3301 (FRC) as well as that
Check the soldering condition. between pin (N20) of IC3302 and pin
(13) of IC3301.
YES NO
Replace IC3301(FRC). Check RESET-A signal pin (34) of
IC1710 (CPLD).
Backlight failure to light up (LC-46XL1E/RU)
Do all the fluorescent tubes light up? NO Check the individual fluorescent YES Replace any defective fluorescent
tubes for light-up failure. tubes with new ones.
YES
Is the power supplied to CN7401 and NO Check the connection between power
CN7601 on the inverter unit? (LA) unit and inverter unit.
YES
Is the fuse (F7401 or F7601) in the NO Replace the blown-out fuse (F7401 or YES Check T7401 and T7601 and their
inverter unit circuit functioning? F7601) on the inverter unit. Turn on peripheral circuits as well as IC7401
the power again. and their peripheral circuits.
If the fuse gets blown out again,
check the short-circuited spot.
YES
Is the VCC power supplied to the NO Check the circuit connected with the
control IC (IC7401) on the inverter VCC terminal on the inverter control
unit? IC (IC7401).
YES
Has each control signal come to NO Have INV-OFL/OSC and the INV-STB NO Check pins (19), (17) and (89) of
CN7402? (INV-OFL, INV-OSC, INV- signal come to P1701 (LB) in the IC1710 (main PWB).
STB, INV-BRT) MAIN substrate?
YES
Is the specified control signal input- NO Check the line between CN7402 and
ted at IC7401 (INV-CTL) on the IC7401.
inverter unit.
YES
Are the Q7405 and Q7406 transis- NO Check the power line of IC7401, Its
tors at the primary side of T7401 peripheral circuits or replace IC7401.
functioning?
YES
Is the secondary circuit of T7401 NO Replace T7401 or the T74** trans-
functioning. former for the fluorescent tubes, or
check their peripheral circuits.
4 18
Backlight failure to light up (LC-52XL1E/RU)
Do all the fluorescent tubes light up? NO Check the individual fluorescent YES Replace any defective fluorescent
tubes for light-up failure. tubes with new ones.
YES
Is the power supplied to CN7507B NO Check the connection between power
and CN7507D on the inverter unit? unit and inverter unit.
YES
Is the fuse (F7501A/B/C/D) in the NO Replace the blown-out fuse (F7501A/ YES Check T7501A, T7501B, T7501C and
inverter unit circuit functioning? B/C/D) on the inverter unit. Turn on T7501D and their peripheral circuits
the power again. as well as IC7502B and their periph-
If the fuse gets blown out again, eral circuits.
check the short-circuited spot.
YES
Is the VCC power supplied to the NO Check the circuit connected with the
control IC (IC7502B) on the inverter VCC terminal on the inverter control
unit? IC (IC7502B).
YES
Has each control signal come to NO Have INV-OFL/OSC and the INV-STB NO Check pins (19), (17) and (89) of
CN7508B? (INV-OFL, INV-OSC, signal come to P1701 (LB) in the IC1710 (main PWB).
INV-STB, INV-BRT) MAIN substrate?
YES
Is the specified control signal input- NO Check the line between CN7508B
ted at IC7502B (INV-CTL) on the and IC7502B.
inverter unit.
YES
Are the Q7501B, Q7502B, Q7503B NO Check the power line of IC7502B, its
and Q7504B transistors at the pri- peripheral circuits or replace
mary side of T7501B functioning? IC7502B.
YES
Is the secondary circuit of T7501B NO Replace T7501B or the T75*** trans-
functioning. former for the fluorescent tubes, or
check their peripheral circuits.
LCD failure 1
Does a single or several verti- Does a single or several hori- Do luminescent or black dots Is the on-screen image rip-
cal stripes appear on the LCD zontal stripes appear on the appear on the screen? pling or distorted?
screen? LCD screen?
Replace the LCD panel.
LCD failure 2
The backlight func- Does the entire LCD Does the QS drive func- Are the data bit drop- Is the gamma correc-
tions. Does not the screen look whitish all tion? out? tion as specified?
image come out in the over? (No solution even when
LCD screen (screen turning on and off the QS
black)? drive)
Replace the LCD control unit.
4 19
LED blinking timing table
250ms 1sec
Type of error Kind of LED Power LED operation (1 cycle) Remarks

H:OFF
Lamp error STANDBY LED Blinking once
L:ON
H:OFF
Lamp error STANDBY LED Blinking once
At five time accumulation L:ON
H:OFF The lamp is turned off
SLEEP TIMER LED Blinking once when it is abnormal usually.
L:ON
H:OFF
Power error STANDBY LED Blinking twice
L:ON
H:OFF
Temperature error STANDBY LED Five time blinking
L:ON
H:OFF
FAN error STANDBY LED Seven time blinking
L:ON
FRC-UNIT (DUNTKE046FE02) circuit failure (1)
No sound or picture come out.

The screen is overall abnormal.
Confirm whether the power supply is defective. Are 12V input to P4802?
Confirm whether 12V is output from CN8 (FL).
YES Are 3.3V output from pin2 of IC4803?

Are 2.5V output from pin2 of IC4802?
YES
Confirm the IC6341 (FPGA) circuit. Is the clock output from X6341 at 33MHz cycle?
Confirm the surrounding of IC6342 (PROM).
Confirm the surrounding of IC6341 (FPGA).
YES YES
Confirm the IC5801 (FRC) circuit. Is the clock output from X5801 at 27MHz cycle?
Confirm the surrounding the IC5801 (FRC).
FRC-UNIT (DUNTKE046FE02) circuit failure (2)
The screen is horizontally displayed only at intervals of one.

The display of putting of one is abnormal.
A horizontal even number line is abnormal ..not going out... A horizontal odd number line is abnormal ..not going out...
Check the surrounding of IC6281(LVDS_RX_even). Check the surrounding of IC6282(LVDS_RX_odd).
FRC-UNIT(DUNTKE046FE02) circuit failure (3)
The screen upper half is abnormal ..not going out... The screen lower half is abnormal ..not going out...
Check the connection of SC6211. Check the connection of SC6212.
Check the surrounding of IC6212(LVDS_TX_upper). Check the surrounding of IC6211(LVDS_TX_lower).
4 20
CHAPTER 5. MAJOR IC INFORMATIONS Service
LC46XL1E
Manual
[1] MAJOR IC INFORMATIONS

1. DESCRIPTION OF MAJOR ICs
Dwg.
Ref No. Name Part Code Description
Code
IC1905 HDMI-Receiver VHiSii9025+-1Q The SiI9025 is a second generation panel Link Cinema receiver that is compati- M1
ble with the HDMI 1.2 (High Definition Multimedia interface) specification.
The SiI9025 is capable of receiving and outputting two channel digital audio at up
to 192KHz - an excellent solution for Digital TVs.
The features of this IC is as follow.
1) Digital video interface supports video processors:
2) Analog RGB and YPbPr output: 10-bit DAC
3) Digital audio interface supports high-end audio systems:
IC3002 VIDEO RH-iXB755WJZZ This is a video processor IC. M3
PROCESSOR This IC has the following six major functions.
1) Video Processing
2) CPU
3) Scaling, Display Processing
4) Video decoder and 3D Combfilter
5) OSD and Text
6) PC Connectivity
IC3501 256Mb-DDR RH-iXB765WJZZQ This is a 256Mb DDR SDRAM IC. This IC features a double-data rate dynamic M4
IC3502 SDRAM random-access memory containing 16M-bits columns by 16 bits.
In this model, it uses it as a memory for the micon and a frame memory for Video
Processor, etc.
IC3503 128Mbit-FLASH RH-iXB754WJZZ This IC is a NOR-type 128Mbit Flash Memory. M4
Memory The Flash Memory stores the main program hat is used for the CPU.
IC3504 D-TYPE RATCH RH-iXB753WJZZ This is a 16bit D-type RATCH-3 state output IC. M4
On this model, the IC is used to transfer the main program from the flash memory
to the CPU.
IC3701 MSP4410K RH-iXB752WJZZQ This MSP (4410K) of single-chip Multistandard Sound Processors covers the M5
sound processing of all analog TV-Standards worldwide, as well as the NICAM
digital sound standards and FM stereo radio.
IC3702 AK4363VF VHiAK4363VF-1Y The AK4363 is a stereo CMOS D/A Converter and Phase Locked Loop for use in M5
digital video broadcast set-top box applications or DVD. The DAC signal outputs
are single-ended and are analog filtered to remove out of band noise.
Therefore no external filters are required. The PLL provides selectable sampling
clock frequencies locked to the 27MHz recovered MPEG clock.
IC3301 FRC B2 Version RH-iXB064WJN1Q This is an IC for Frame Rate Converter. M6
This IC mainly processes I/P conversion: Standard 50/60 Hz interlaced to 50/60
Hz progressive.
It also has the following functions:
1) Image Improvement: (Chroma Transient Improvement, Luminance Transient
Improvement, Dynamic Contrast Improvement, Back Stretcher)
2) Film mode detection (2-2/3-2 pull down)
3) Film judder cancellation.
IC2301 RS232C VHiiCL3225E-1Y This IC is a line driver receiver in conformity with EIA/TIA-232-E (former RS- M7
Transmitters/ 232C) standard.
Receivers By connecting a PC, the system can be controlled externally.
IC1710 CPLD RH-iXB946WJZZQ This IC is C.P.L.D (Complex Programmable Logic Device) for signal selector and M8
synchronous processing of each digitalized input signal.
This IC functions as extended I/O of the main microcontroller and controls timing
of bus signals among ICs, etc.
IC1712/08 Stepdown VHiMP1410ES-1Y The MP1410 is a monolithic step down switch mode regulator with a built in inter- M8
Converter nal power MOSFET.
In this model, it works to 1.8V regulator.
IC1706 Stepdown VHiMP1583++-1Y The MP1583 is a step-down DC-DC converter of Class 3A current capacity. M8
Converter In this model, it works to BU1.8V regulator.
IC3001 E2PROM RH-iXA992WJZZY The BR24L64F is a 2-wire (I2C bus type) serial EEPROM that is electrically M1
(VHiBR24L64F-1Y) programmable.
This IC serves to store the adjustment and other data in the adjustment process
mode.
The data is given out by commands from the main microprocessor.
51
Dwg.
Code
IC1901 E2PROM VHi24LC2BiN-1Y This IC is a 2-wire (I2C bus type) serial EEPROM this is electrically programma- M1
IC1902 ble.
The EEPROM chip stores the EDID data of HDMI input.
This data is controlled through I2C signals.
IC2303 E2PROM VHiBR24C21F-1Y This IC is a 2-wire (I2C bus type) serial EEPROM this is electrically programma- M5
ble.
The EEPROM chip stores the EDID data of PC input.
This data is controlled through I2C signals.
[AV SECTION]
IC301 Sound Amp VHiTDA8931T-1Y The TDA8931 is a switching power stage for high efficiency class-D audio power AV1
IC302 amplifier systems.
With this amplifier a compact 1x 20 W closed loop self-oscillating digital amplifier
system can be built.
In this model, Audio amplifier is 15watt *2.
[POWER SECTION]
Z1 Switching SPT9001 This IC is a power supply for the switching regulator on the primary side. P1
Regulator Overvoltage/overcurrent protection circuit, other protection circuits and control
circuits are built in this IC.
IC702 Switching STR-W6765 This IC is a power supply for the switching regulator on the primary side. P1
Regulator The STR-W6765 is a Low EMI noise and soft switching designed for SMPS
applications.
IC701 Power Factor MC33262 The MC33262 are active power factor controllers specifically designed for use as P1
Correction IC a preconverter in electronic ballast and in off.line power converter applications.
[DIGITAL SECTION]
IC4001 DTV- RH-iXB680WJZZQ This is a video/audio signal processing IC (Digital Processor) (STi5516) for digital D1
PROCESSOR tuner, which has been manufactured by STMicroelectronics, and incorporates a
CPU. In this equipment, it implements GUI processing and video/audio process-
ing for digital tuner, negotiation processing with CI-CARD, etc.
IC4201 64M-SDRAM RH-iXB742WJZZQ This IC is 64Mb SDRAM (static dynamic random-access memory) IC. D2
IC4202 In this equipment, it is used for SMI memory (for image processing), and data is
used for operation of the digital processor.
IC4203 16Mbit-FLASH RH-iXC100WJZZQ This IC is a high performance CMOS super technology 16Mbit Flash Memory. D2
Start software (loader) for the CPU with a built-in digital processor and application
software have been written on this Flash Memory.
The digital processor reads these softwares on start-up and implements them.
IC4402/05 RATCH- VHiLVC573FT-1Y This is a RATCH-3 STATE output IC. In this equipment, it is used to establish D3
3 STATE negotiation communication with CI-CARD.
IC4401 BALANCE VHiLCX245FT-1Y This IC is a low voltage (3.3V) CMOS 8bit bidirectional transceiver. When setting D3
TRANCEIVER the transmission direction change input DIR to H, the A bus is switched to input
and the B bus is changed to output; if the DIR is set to L, the B bus is switched
to input and the A bus is changed to output. When setting the enable input OE to
H, both A and B buses enter the high impedance state. In this equipment, it
used to switch bus of the data from CICARD.
IC4404 BUS Buffer VHiLCX244FT-1Y This lC is fabricated with an advanced CMOS technology to achieve high speed D3
operation while maintaining CMOS low power dissipation.
In this equipment, it is used to control negotiation communication with CI-CARD.
IC4604 3-OP-AMP VHiTSH73CPT-1Y This IC is a Triple operational amplifiers featuring high video performances with D4
large bandwidth, low distortion and excellent supply voltage rejection. In this
equipment, it is used to convert audio output signal of the digital processor to nor-
mal analog signal level and to buffer it.
[DIGITAL TUNER section]
IC201 IF-PLL-DEMOD VHiTDA9886+-1 The TDA9886 is an alignment-free multistandard (PAL, SECAM and NTSC) TUNER
Vision and sound IF signal PLL demodulator for positive and negative modula-
tion, including sound AM and FM processing.
IC202 COFDM Demod RH-iXB964WJZZQ This is a COFDM (Coded Orthogonal Frequency Division Multiplex) Demodulator TUNER
IC IC. In this equipment, IF signal from the digital tuner is decoded to MPEG-2 sig-
nal, and it is digitally output. Output signal is fed to the digital processor to imple-
ment video/audio decode processing. This IC is used for digital signal is fed to the
digital processor to implement video/audio decode processing.
This IC is used for digital tuner only.
[FRC SECTION]
IC6281/82 LVDS-Receiver VHiTLVD104S-1Q This is a 30bits color LVDS (Low-Voltage Differential Signaling) receiver IC. F1
At a transmit clock frequency of 112MHz, 30bits of RGB data and 5bits of timing
and control data (HSYNC, VSYNC, DE, CNTL1, CNTL2) are transmitted at an
effective rate of 784Mbps per LVDS channel.
52
Dwg.
Code
IC6341 FPGA RH-iXC029WJQZQ This is an FPGA (Field Programmable Gate Array) IC. F2
In this unit, it performs phase difference absorption of ODD/EVEN of the video
input signal, I2C slave address conversion, and identification of the pulse drive
system.
IC6342 PROM RH-iXC030WJQZQ This is a PROM (Programmable Read Only Memory) IC. F2
This IC stores the program contents of FPGA (IC6341).
IC5801 FRC RH-iXB857WJZZQ This is an FRC (Field Rate Converter) IC. F3
This IC supports the vertical frequency at double speed of 120Hz and reduces
afterimages.
IC6001 128M-SDRAM RH-iXB822WJQZQ This IC is 128-Mbit GDDR SDRAM (Graphic Double Data Rate Synchronous F4
IC6002 DRAM), providing a memory for image processing and buffering OSD data.
IC6003 In this unit, it stores a frame of two screens and intermediate processing informa-
tion for forming interpolation images.
IC6004 Termination- RH-iXA361WJZZY This is a termination linear regulator IC for DDR-SDRAM. F4
REG This IC incorporates a high-speed operation amplifier providing excellent
response against load variation.
The output stage can provide continuous load current of 1.5A and supports varia-
tion peak of maximum 3A.
IC6211 LVDS- VHiTLVD1023-1Q This is an LVDS (Low-Voltage Differential Signaling) transmitter IC. F5
IC6212 Transmitter This transmitter is designed to support Single Link transmission between Host
and Flat Panel Display up to 1080p resolutions and Dual Link transmission
between Host and Flat Panel Display up to QXGA resolutions.
This IC converts 67bits of CMOS/TTL data into LVDS (Low Voltage Differential
Signaling) data stream.
IC4802 Chopper REG RH-iXA552WJZZY This is a PWM chopper regulator IC. F6
IC4803 This IC is equipped with the output voltage ON/OFF function, overcurrent shut-
down function, overheat protection function, standby low power consumption
function, and soft start circuit.
In this unit, it forms a 2.5V regulator circuit.
IC4801 DC/DC-CONV VHiTPS40055-1Y This is a DC/DC converter IC. F6
In this unit, it forms a 1.2V regulator circuit.
The TPS4005x is a family of high-voltage, wide input (8 V to 40 V), synchronous,
step-down converters. The TPS4005x family offers design flexibility with a variety
of user programmable functions, including soft-start, UVLO, operating frequency,
voltage feed- forward, high-side current limit, and loop compensation. current
limit, and loop compensation.
53
2. IC201: VHiTDA9886+-1
IF-PLL DEMODULATORS
Pin No. Pin Name I/O Pin Function

1 VIF1 I VIF differential input 1
2 VIF2 I VIF differential input 2
3 OP1 O Output port 1; open-collector.
4 FMPLL I FM-PLL for loop filter.
5 DEEM O De-emphasis output for capacitor.
6 AFD I AF decoupling input for capacitor
7 DGND Digital ground.
8 AUD O audio output.
9 TOP I tuner AGC TakeOver Pint (TOP) for resistor adjustment.
10 SDA I/O I2C-bus data input and output.
11 SCL I I2C-bus clock input.
12 SIOMAD O sound intercarrier output and MAD select with resistor.
13 N.C. not connected.
14 TAGC O tuner AGC output.
15 REF I 4 MHz crystal or reference signal input.
16 VAGC(1) I VIF-AGC for capacitor.
17 CVBS O composite video output.
18 AGND analog ground.
19 VPLL I VIF-PLL for loop filter.
20 VP supply voltage.
21 AFC O AFC output.
22 OP2 O output port 2; open-collector.
23 SIF1 I SIF differential input 1 and MAD select with resistor.
24 SIF2 I SIF differential input 2 and MAD select with resistor.
54
3. IC202: RH-iXB964WJZZ (STV0362)
DVB-T RECEIVER
Pin No Pin Name I/O Pin Function

32 NOT_RESET I Hardware reset, active Low.
15 XTAL_I I Crystal oscillator input/external clock (2.5V)
14 XTAL_O O Crystal oscillator output.
1 RF_LEVEL I ADC 8 input for RF level monitoring.
3 QP I Positive Q analog input for baseband configuration,
4 QM I Nagative Q analog input for baseband configuration.
5 VDDA_ISO Analog ISO neutral polarization.
7 REFP Internal positive reference.
8 REFM Internal negative reference.
9 INCM Internal common mode.
10 IM I Negative 1 analog input for IF and baseband configuration.
11 IP I Positive 1 analog input for IF and baseband configuration.
12 VDDA_1V0 Analog supply (1.0V)
29 SDA I/O Serial data (open drain)
30 SCL I Serial clock (open drain)
21 SDAT I/O SDA tuner (open drain)
20 SCLT I SCL tuner.
43 D7 O Serial MPEG data or parallel MPEG data (bit 7)
42 D6 O Parallel MPEG data (bit 6)
44 CLK_OUT O MPEG byte or bit clock
46 STR_OUT O MPEG first byte sync.
47 D/NOT_P O MPEG data valid/parity
48 ERROR O MPEG packet error
18 AGC_RF I/O RF AGC control (5V tolerant)
17 AGC_IF I/O IF AGC control (5V tolerant)
55
64 TEST Reserved test mode, must be grounded.
27 GPIO0 I/O General-purpose input/output port 0.
Reserved test mode, must be ground.
60 GPIO2 I/O General-purpose input/output port 2 or lock indicator.
59 GPIO3 I/O General-purpose input/output port 3 or lock indicator.
Resen must be ground.
23 AUX_CLK I/O Auxiliary clock.
25 CS0 I Chip select LSB.
2,6,13,16 VDDA_2V5 Analog power supply (2.5V)
19, 24, 31, 38, VDD_1V0 Digital core supply (1.0V)
45, 51, 55, 62
22, 28, 34, 41, VDD_3V3 Digital I/O supply (3.3V)
50, 56, 63
4. IC701: MC33262
POWER FACTOR CONTROLLER

1 FB I Feedback input terminal of converter output voltage.
2 COMP Compensation terminal of error amplifier.
3 MUL I Multiplier input terminal of sine wave AC power wave form.
4 IS I Input terminal to detect current of MOSFET.
5 ZCD I Input terminal to detect current of inductor returning to 0.
6 GND Ground.
7 OUT O Output terminal to drive MOSFET directry.
8 Vcc I Power supply input terminal to operate IC.
56
5. IC704: STR-W6765
SWITCHING REGULATOR

1 D I Drain (MOSFET drain)
2 NC Clipped (No connection)
3 S/GND Source/ground terminal (MOSFET source and ground)
4 VCC Power supply terminal (Input of power supply for control circuit)
5 SS/OLP I Soft Start/Overload Protection terminal
(Input to set delay for Overload Protection and Soft Start operation)
6 FB I Feedback terminal
(Input for Constant Voltage Control and Burst Mode oscillation control signals)
7 OCP/BD Overcurrent Protection/Bottom Detection
(Input for overcurrent detection and bottom detection signals)
57
6. IC1710: RH-IXB946WJZZ
CPLD
Pin No. Pin Name I/O Pin Function Sheet Name

1 EXP[8] O REG2 light control system identify (INT: L) REG2
2 EXP[9] O REG external sync identify (INT: L) REG
3 EXP[10] O QS (Quick Shoot) parameter (INT: L) TEMP3
6 EXP[13] O QS (Quick Shoot) parameter (INT: L) QSSET
7 EXP[14] O LED SLEEP (Light-up at L) (INT: H) LEDSLP
58
8 EXP[15] O LED OPC (Light-up at L) (INT: H) LEDOPC
9 VCCIO1 3.3V Power supply 3.3V 3.3V
10 GND Ground GND
11 GND Ground GND
12 PCLK I Panel clock 74.25MHz PCLK
13 VCCINT 3.3V Power supply 3.3V 3.3V
14 I/O GND* NC
15 I/O GND* NC
16 I/O GND* NC
17 OSCOUT O Light control clock output (No lamp light-up at initial L) OSCOUT
18 I/O GND* NC
19 OFLOUT O Light control PWM output (No lamp light-up at initial L) OFL1OUT
20 OFL2OUT O Light control PWM output OFL2OUT
21 I/O GND* NC
22 (TMS) I/O Inline Program JTAG TMS/OPEN TMS
23 (TDI) I/O Inline Program JTAG DataIn/OPEN TDI
24 (TCK) I/O Inline Program JTAG Clock/OPEN TCK
25 (TDO) O Inline Program JTAG DataOut/OPEN TDO
26 I/O I Write mode Vpp-cont NC
27 I/O GND* NC
28 I/O GND* NC
29 I/O GND* NC
30 I/O GND* NC
32 GND Ground GND
33 I/O GND* NC
34 EXP[16] O MSP&FRC Reset: Note 2 (INT: L) RESET_A
35 EXP[17] O DTU-CVBS/ (S-VY CVBS) switching (INT: L) G_ONSYNC
36 EXP[18] O DTV/PC/HDMI switching (INT: L) DTVPC
37 EXP[19] O DTV/PC/HDMI switching (INT: L) DTVHDMI
38 EXP[20] O E2PROM WP for HDMI (INT: L) HDMI_WP
39 EXP[21] O Panel flip horizontal (INT: L) LCDLR
40 EXP[22] O Panel flip vertical (INT: L) LCDUD
41 EXP[23] O Panel 50/60Hz (INT: L) FRAME
42 I/O GND* NC
43 I/O GND* NC
44 I/O GND* NC
46 GND Ground GND
47 EXP[24] O Common Bias Adjustment write Protect. (INT: L) TCON_WP
48 EXP[25] O FRC_I2C_SW (INT: L) FRC_I2C_SW
49 EXP[26] O Charge share impulse control (on/off). (INT: L) CSI
50 EXP[27] O Pcom1.5-control (INT: L) Ppcon1.5
51 EXP[28] O Panel Control. (INT: L) BANK
52 EXP[29] O Not used NC
53 EXP[30] O Not used NC
54 EXP[31] O Reset Trigger NC
55 I/O GND* NC
56 I/O GND* NC
57 I/O GND* NC
58 I/O GND* NC
60 GND Ground GND
61 I/O GND* NC
62 GCLR I VGC_Reset_Line RESET_N
63 VCCINT 3.3V Power supply 3.3V 3.3V
64 SCK I Serial Clock (from VGC) SCK
65 GND Ground GND
66 SEN I Serial Data Enable (from VGC) FPGA_SDE
67 SDAI I Serial Data (from VGC) FPGA_SDA
68 I/O GND* NC
69 SDAO O Serial Data Output enable (from VGC) (INT: L) FPGA_SDAO
70 I/O GND* NC
71 I/O GND* NC
59
72 I/O GND* NC
73 I/O GND* NC
74 I/O GND* NC
75 OFL2EN I OFL2 output enable GND
76 I/O GND* NC
77 I/O O VGC soft write (Write mode at H) (INT: L) BOOT
78 I/O GND* NC
79 GND Ground GND
81 I/O I VSYNC_OSC VSYNC
82 I/O I HSYNC_OSC HSYNC
83 I/O GND* NC
84 I/O GND* NC
85 EXP[0] O Digital Tuner I2C Selector (INT: L) DTI2CSEL
86 EXP[1] O DTM_RESET (INT: L) DTM_RESET
87 EXP[2] O DTU_ON (Analog tuner at L, D-tuner at H) (INT: L) DTU_ON
88 EXP[3] O 232C on/off SW (RS232C action at H: VGC write enabled) (INT: H) IREM_SW
89 EXP[4] O Set Top Box (LAMP ON) (INT: L) STB
90 EXP[5] O S2_MUTE (INT: L) S_2MUTE
91 EXP[6] O ANT+5V ON ANT+5V ON
92 EXP[7] O S_MUTE (INT: L) S-MUTE
93 GND Ground GND
95 I/O GND* NC
96 I/O GND* NC
97 I/O GND* NC
98 I/O used to TP1703 TP1703
99 I/O GND* NC
100 OFL-SET-IN I OFLWD[8] external setting terminal GND
GND*: Non-configured pins are fixed at GND.

Terminals' electrical characteristics are referred to in the EPM240T100C5N data sheet of Altera.
Note 1: Reset output monitor terminal with EXP31 in use.
Note 2: Composed of GCLR and OR.
5 10
7. IC1905: VHiSii9025+-1Q
HDMI RECIEVER

144 Q0 O 24-bit Output Pixel Data Bus. HDMI-B[0]
5 11
132 Q8 O 24-bit Output Pixel Data Bus. HDMI-G[0]
119 Q16 O 24-bit Output Pixel Data Bus. HDMI-R[0]
1 DE O Data enable.
2 HSYNC O Horizontal Sync Output control signal.
3 VSYNC O Vertical Syanc Output control signal.
121 ODCK O Output Data Clock. HDMI-CLK
97 XTALIN I Crystal Clock Input.
96 XTALOUT O Crystal Clock Output.
88 MCLKOUT O Audio Master Clock Output.
87 MCLKIN I Audio Master Clock Input Reference.
86 SCK O I2S Serial Clock Output.
85 WS O I2S Word Select Output.
84 SDO O I2S Serial Data Output.
78 SPDIF O S/PDIF Audio Output
77 MUTEOUT O Mute Audio Output.
104 INT O Interrupt Output.
102 RESET# I Reset Pin. Active LOW. 5V Tolerant.
32 DSCL0 I DDC I2C Clock for Port 0. 5V Tolerant.
31 DSDA0 I/O DDC I2C Data for Port 0. 5V Tolerant.
30 DSCL1 I DDC I2C Clock for Port 1. 5V Tolerant.
29 DSDA1 I/O DDC I2C Data for Port 1. 5V Tolerant.
28 CSCL I Configuration I2C Clock. 5V Tolerant.
27 CSDA I/O Configuration I2C Data. 5V Tolerant.
103 SCDT O Indicates active video at HDMI input port.
107 CLK48B I/O Data Bus Latch Enable. 2
34 R0PWR5V I Port 0 Transmitter Detect. 5V Tolerant.
33 R1PWR5V I Port 1 Transmitter Detect. 5V Tolerant.
101 TEST I Test Terminal.
6.7.13.19 VCC VCC (3.3V)
8.12.18 GND Ground
10 RSET O Reset Pin.
11 COMP I Comparator
14, 17, 20, 56, NC No internal connection.
81, 82, 83, 93,
100
9 EVNODD O Even/Odd field for interlaced modes.
40 R0XC+ I TMDS input clock pair. HDMI Port 0.
39 R0XC- I TMDS input clock pair. HDMI Port 0.
44 R0X0+ I TMDS input data pair. HDMI Port 0.
43 R0X0- I TMDS input data pair. HDMI Port 0.
59 R1XC+ I TMDS input clock pair. HDMI Port 1.
58 R1XC- I TMDS input clock pair. HDMI Port 1.
5 12
22, 23, 35, 74, CVCC18 Digital Logic VCC. (1.8V)
79, 92, 105, 114,
128, 139
21, 24, 36, 73, CGND Digital Logic GND.
80, 91, 106, 115,
127, 138
5, 16, 26, 76, 89, IOVCC Input/Output Pin VCC. (3.3V)
109, 122, 134
4, 15, 25, 75, 90, IOGND Input/Output Pin GND.
108, 120, 135
38, 42, 46, 50, AVCC TMDS Analog VCC. (3.3V)
57, 61, 65, 69
41, 45, 49, 53, AGND TMDS Analog GND.
60, 64, 68, 72
37 PVCC0 TMDS Port 0 PLL VCC. (3.3V)
55 PVCC1 TMDS Port 1 PLL VCC. (3.3V)
54 TMDSPGND TMDS PLL GND.
94 AUDPVCC18 ACR PLL VCC. (1.8V)
95 AUDPGND ACR PLL GND.
98 XTALVCC ACR PLL Crystal Input VCC. (3.3V)
99 REGVCC ACR PLL Regulator VCC. (3.3V)
5 13
8. IC3002: RH-IXB755WJZZ
VIDEO GRAPHICS CONTROLLER
Pin No. Pin Name I/O Pin Function Seet name Destination
M23 XIN I 20. 25MHz clock or crystal input X3001
M22 XOUT O Output to a crystal that is connected to XIN. X3001
D18 RESET_N I Reset input (active low) RESET_N IC1710 62pin
G15 POR_N O Power-on reset generator (active low), May be connected to NC
RESET_N.
H7 TM I Test mode enable. IC3001 8pin
L20 VARCLK O Vriable clock output (e.g. FRC94xxAclk) NC
Y20 CV01 O Analog video out (CVBS or Y) (EXT2-VOUT2) CVO1 SC2703 15pin
Y23 CV02 O Analog video out (CVBS or Y) (EXT1-VOUT1) CVO2 SC2702 15pin
Y22 CV03 O (pull up) CVO3 BU3.3V
Y21 CV04 O (pull up) CVO4 BU3.3V
AA23 CV05 O (pull up) CVO5 BU3.3V
AA22 CV06 O (pull up) CV06 BU3.3V
AB23 CV09 O (pull up) CVO9 BU3.3V
AC23 CVI1 I Analog video in (CVBS) (TUNER CVBS IN) CVBS SC2705 2pin
AB22 CVI2 I Analog video in (CVBS) (EXT1 VIN1) VIN1 SC2702 10pin
AC22 CVI3 I GND
AA21 CVI4 I Analog video in (CVBS) (DVB CVBS IN) DTV_CVBS P2702 33pin
AB20 YI1 I Analog video in (Y or CVBS) (EXT3 CVBS IN) IN3Y SC2703 21pin
AB21 YI2 I Analog video in (Y or CVBS) (EXT2 Y/CVBS IN) VIN2 SC2703 10pin
AA20 YI3 I GND
AC20 CI1 I Analog video in (chroma) (EXT3 IN3C IN) IN3C SC2703 23Pin
AC21 CI2 I Analog video in (chroma) (EXT2 C2 IN) C2 SC2703 4pin
AC19 CI3 I GND
Y19 RI1 I Analog component input 1 (EXT1-RED1) RED1 SC2702 4pin
AB19 GI1 I Analog component input 1 (EXT1-GREEN1) GREEN1 SC2702 6pin
AC18 BI1 I Analog component input 1 (EXT1-BLUE1) BLUE1 SC2702 8pin
AA19 FBI1 I Analog component input 1 (EXT1-FAST-SW1) IN1FSW SC2702 1pin
AA18 RI2 I Analog component input2 (DVB-R) DTV_R P2702 36pin
AB18 GI2 I Analog component input2 (DVB-G) DTV_G P2702 32pin
Y18 BI2 I Analog component input2 (DVB-B) DTV_B P2702 28pin
AC17 FBI2 I Analog component input2 GND GND
5 14
AA17 RI3 I Analog component input3 (APC_R) APC_R SC2303 2pin
AB17 GI3 I Analog component input3 (APC_G) APC_G SC2303 1pin
Y17 BI3 I Analog component input3 (APC_B) APC_B SC2303 3pin
AC16 FBI3 I Horizontal sync input. (PCV_H) PCVH IC2306 1pin
W21 VIN I Vertical sync input. (PCV_V) PCVV IC2305 6pin
B17 I2SWS I I2S word strobe (digital audio left/right select input) I2SWS IC3701 11pin
C17 I2SCL I I2S clock (digital audio bit clock input) I2SCL IC3701 10pin
D17 I2SDA1 I I2S data input (PCM audio data) I2SDA1 IC3701 9pin
A18 I2SDA0 O I2S data output (PCM audio data) I2SDAO IC3701 8pin
L3 RAMD_31 I/O DDR-SDRAM bi-directional data bus. (SDRAM-RAMD_31) DDR_DQ31 IC3502 65pin
L4 RAMD_30 I/O DDR-SDRAM bi-directional data bus. (SDRAM-RAMD_30) DDR_DQ30 IC3502 63pin
K3 RAMD_29 I/O DDR-SDRAM bi-directional data bus. (SDRAM-RAMD_29) DDR_DQ29 IC3502 62pin
J3 RAMD_26 I/O DDR-SDRAM bi-directional data bus. (SDRAM-RAMD_26) DDR_DQ26 IC3502 57pin
J4 RAMD_25 I/O DDR-SDRAM bi-directional data bus. (SDRAM-RAMD_25) DDR_DQ25 IC3502 56pin
H3 RAMD_24 I/O DDR-SDRAM bi-directional data bus. (SDRAM-RAMD_24) DDR_DQ24 IC3502 54pin
G3 RAMD_22 I/O DDR-SDRAM bi-directional data bus. (SDRAM-RAMD_22) DDR_DQ22 IC3502 11pin
F3 RAMD_20 I/O DDR-SDRAM bi-directional data bus. (SDRAM-RAMD_20) DDR_DQ20 IC3502 8pin
C1 RAMD_15 I/O DDR-SDRAM bi-directional data bus. (SDRAM-RAMD_15) DDR_DQ15 IC3501 65pin
D2 RAMD_14 I/O DDR-SDRAM bi-directional data bus. (SDRAM-RAMD_14) DDR_DQ14 IC3501 63pin
E2 RAMD_12 I/O DDR-SDRAM bi-directional data bus. (SDRAM-RAMD_12) DDR_DQ12 IC3501 60pin
A7 RAMD_3 I/O DDR-SDRAM bi-directional data bus. (SDRAM-RAMD_3) DDR_DQ3 IC3501 7pin
B6 RAMD_2 I/O DDR-SDRAM bi-directional data bus. (SDRAM-RAMD_2) DDR_DQ2 IC3501 5pin
A6 RAMD_1 I/O DDR-SDRAM bi-directional data bus. (SDRAM-RAMD_1) DDR_DQ1 IC3501 4pin
B5 RAMD_0 I/O DDR-SDRAM bi-directional data bus. (SDRAM-RAMD_0) DDR_DQ0 IC3501 2pin
A2 RAMA_12 O Address bits for DRAM (Row/Col) (SDRAM-RAMA_12) DDR_A12 IC3501 42pin
D8 RAMA_10 O Address bits for DRAM (Row/Col) (SDRAM-RAMA_10) DDR_A10 IC3501 28pin
B3 RAMA_9 O Address bits for DRAM (Row/Col) (SDRAM-RAMA_9) DDR_A9 IC3501 40pin
C3 RAMA_6 O Address bits for DRAM (Row/Col) (SDRAM-RAMA_6) DDR_A6 IC3501 37pin
AlO RAMA_2 O Address bits for DRAM (Row/Col) (SDRAM-RAMA_2) DDR_A2 IC3501 31pin
C8 RAMBA_1 O DRAM bank select (SDRAM-RAM_BA1) DDR_BA1 IC3501 27pin
D7 RAMBA_0 O DRAM bank select (SDRAM-RAM_BA0) DDR_BA0 IC3501 26pin
B8 RAMRAS_N O DRAM row address strobe (active low) (SDRAM-RAMRAS_N) N_DDR_RAS IC3501 23pin
A8 RAMCAS_N O DRAM column address strobe (active low) (SDRAM-RAMCAS_N) N_DDR_CAS IC3501 22pin
J1 RAMDM_3 O DRAM byte mask lines. (SDRAM-RAMDM_3) DDR_DM3
J2 RAMDM_2 O DRAM byte mask lines. (SDRAM-RAMDM_2) DDR_DM2
F2 RAMDM_1 O DRAM byte mask lines. (SDRAM-RAMDM_1) DDR_DM1 IC3501 47pin
C5 RAMDM_0 O DRAM byte mask lines. (SDRAM-RAMDM_0) DDR_DM0 IC3501 20pin
B7 RAMWE_N O DRAM write enable (active low) (SDRAM-RAMWE_N) RAMWE_N
A9 RAMCS_N O DRAM chip select (active low) (SDRAM-RAMCS_N) RAMCS_N
5 15
A1 RAMCKE O DRAM clock enable. (SDRAM-RAMCKE) RAMCKE
B2 RAMCLK O DRAM clock output. (SDRAM-RAMCLK) RAMCLK
C2 RAMCLK_N O DRAM clock output (inverted) (SDRAM-RAMCLK_N) RAMCLK_N
K2 RAMDQS_3 I/O Strobe signal. (SDRAM-RAMDQS_3) RAMDQS_3
H1 RAMDQS_2 I/O Strobe signal. (SDRAM-RAMDQS_2) RAMDQS_2
E1 RAMDQS_1 I/O Strobe signal. (SDRAM-RAMDQS_1) RAMDQS_1
A5 RAMDQS_0 I/O Strobe signal. (SDRAM-RAMDQS_0) RAMDQS_0
B1 RAMCLKIN I Clock (RAMCLK) feed back. (SDRAM-RAMCLKIN) RAMCLKIN
G7 SSTLVREF I SSTL2 Reference Voltage. (SDRAM-SSTLVREF) SSTL
K20 SCL1 I 12C bus 1clock. SCL1 IC3001
K21 SDA1 I/O 12C bus 1 data. SDA1 IC3001
B18 SCL2 I 12C bus 2 clock. (no used) BU3.3V
C18 SDA2 I/O 12C bus 2 data. (no used) BU3.3V
H17 TRST I Test reset. TRST P2304 1pin
G17 TMS I Test mode select. TMS P2304 7pin
G8 TDO O Test data output. TDO P2304 5PIN
G16 TCLK I Test clock. TCLK P2304 9PIN
G9 TDI I Test data input. TDI P2304 3PIN
M20 CADC5 I CADC analog source input. (KEY-1) (to key-unit) KEY1 P2302 1pin
M21 CADC4 I CADC analog source input. (TH3001) PICAA1 TH3001
L21 CADC3 I CADC analog source input. (OPCIN) OPCIN
K22 CADC2 I CADC analog source input. (KEY-2) (to key-unit) IF-AGC/KEY2 P2302 2pin
L22 CADC1 I CADC analog source input. (SLOW_SW1) SLOWSW1 SC2702 3pin
L23 CADC0 I CADC analog source input. (SLOW_SW2) SLOWSW2 SC2703 3pin
N23 DPWM1 O Display-PWM outputs. (PWMOUT-BRT-INV) PWMOUT INV
N22 DPWM2 O NC
W23 DPWM3 O NC
W22 VITUFE O V sync output of ITUE_FE. NC
U3 NVM_22 O NVM_[22:16] upper address bits (to-flash memory) IC3503 2pin
Pull-up and pull-down resistors must be used for boot-process
configuration
M2 NVM_21 O NVM_[22:16] upper address bits (to-flash memory) IC3503 15Pin
M4 NVM_20 O NVM_[22:16] upper address bits (to-flash memory) IC3503 12Pin
L1 NVM_19 O NVM_[22:16] upper address bits (to-flash memory) IC3503 11pin
M1 NVM_18 O NVM_[22:16] upper address bits (to-flash memory) IC3503 18pin
N4 NVM_17 O NVM_[22:16] upper address bits (to-flash memory) IC3503 19pin
U1 NVM_16 O NVM_[22:16] upper address bits (to-flash memory) IC3503 54pin
U4 NVM_15 I/O NVMD_[15:0] multiplexed address/data (to-flash memory) IC3503 51pin IC3504 26piN
T1 NVM_14 I/O NVMD_[15:0] multiplexed address/data (to-flash memory) IC3503 49piN IC3504 27pin
T2 NVM_13 I/O NVMD_[15:0] multiplexed address/data (to-flash memory) IC3503 47pin IC3504 29pin
R1 NVM_10 I/O NVMD_[15:0] multiplexed address/data (to-flash memory) IC3503 40piN IC3504 33pin
R2 NVM_9 I/O NVMD_[15:0] multiplexed address/data (to-flash memory) IC3503 38pin IC3504 35pin
P1 NVM_6 I/O NVMD_[15:0] multiplexed address/data (to-flash memory) IC3503 48pin IC3504 38pin
N1 NVM_2 I/O NVMD_[15:0] multiplexed address/data (to-flash memory) IC3503 39piN IC3504 44pin
N2 NVM_1 I/O NVMD_[15:0] multiplexed address/data (to-flash memory) IC3503 37pin IC3504 46pin
N3 NVM_0 I/O NVMD_[15:0] multiplexed address/data (to-flash memory) IC3503 35pin IC3504 47pin
L2 NVMOE_N O Output enable (active low) IC3503 34pin
M3 NVMWE_N O Write enable (active low) IC3503 13pin
U2 ENVMALE O Address latch enable. NVMALE IC3504 48pin
R7 REXT_LVDS S External Resistor (6.2K, 1%)
AC8 PORT_A_29 I Port A data RGB or LVDS (TA1-) TA1- SC2302 40pin
AB8 PORT_A_28 I Port A data RGB or LVDS (TA1+) TA1+ SC2302 39pin
AC7 PORT_A_27 I Port A data RGB or LVDS (TB1-) TB1- SC2302 38pin
AB7 PORT_A_26 I Port A data RGB or LVDS (TB1+) TB1+ SC2302 37pin
AC6 PORT_A_25 I Port A data RGB or LVDS (TC1-) TC1- SC2302 36pin
AB6 PORT_A_24 I Port A data RGB or LVDS (TC1+) TC1+ SC2302 35pin
AC5 PORT_A_23 I Port A data RGB or LVDS (CK1-) CK1- SC2302 33pin
AB5 PORT_A_22 I Port A data RGB or LVDS (CK1+) CK1+ SC2302 32pin
5 16
AA5 PORT_A_21 I Port A data RGB or LVDS NC NC
Y5 PORT_A_20 I Port A data RGB or LVDS NC NC
AC4 PORT_A_19 I Port A data RGB or LVDS (TD1-) TD1- SC2302 31pin
AB4 PORT_A_18 I Port A data RGB or LVDS (TD1+) TD1+ SC2302 30pin
AC3 PORT_A_17 I Port A data RGB or LVDS (TE1-) TE1- SC2302 29pin
AB3 PORT_A_16 I Port A data RGB or LVDS (TE1+) TE1+ SC2302 28pin
AC1 PORT_A_15 I Port A data RGB or LVDS (TA2-) TA2- SC2302 26pin
AC2 PORT_A_14 I Port A data RGB or LVDS (TA2+) TA2+ SC2302 25pin
AB1 PORT_A_13 I Port A data RGB or LVDS (TB2-) TB2- SC2302 24pin
AB2 PORT_A_12 I Port A data RGB or LVDS (TB2+) TB2+ SC2302 23pin
AA1 PORT_A_9 I Port A data RGB or LVDS (TC2-) TC2- SC2302 22pin
AA2 PORT_A_8 I Port A data RGB or LVDS (TC2+) TC2+ SC2302 21pin
Y1 PORT_A_7 I Port A data RGB or LVDS (CK2-) CK2- SC2302 19pin
Y2 PORT_A_6 I Port A data RGB or LVDS (CK2+) CK2+ SC2302 18pin
W1 PORT_A_5 I Port A data RGB or LVDS (TD2-) TD2- SC2302 17pin
W2 PORT_A_4 I Port A data RGB or LVDS (TD2+) TD2+ SC2302 16pin
V1 PORT_A_3 I Port A data RGB or LVDS (TE2-) TE2- SC2302 15pin
V2 PORT_A_2 I Port A data RGB or LVDS (TE2+) TE2+ SC2302 14pin
V3 PORT_A_1 I Port A data RGB or LVDS NC NC
V4 PORT_A_0 I Port A data RGB or LVDS NC NC
W4 PORT_ A_PCS1 I/O Port A panel control. NC NC
W3 PORT_A_PCS2 I Port A panel control. HSYNC_OSC HSYNC_OSC IC1710 82pin
Y4 PORT_A_PCS3 I Port A panel control. VSYNC_OSC VSYNC_OSC IC1710 81pin
Y3 PORT_A_PCS4 I/O Port A panel control. NC NC
AA6 PORT_A_PCS5 I/O Port A panel control. NC NC
Y7 PORT_A_PCS6 I/O Port A panel control. NC NC
AA7 PORT_A_REV I/O Port A panel control. NC NC
Y6 PORT_A_CLK I/O Port A clock. PCLK_A IC1710 12pin
AB13 PORT_B_16 I/O Port B data. NC NC
Y13 PORT_B_15 I/O Port B data. NC NC
AA12 PORT_B_14 I/O Port B data. NC NC
AC12 PORT_B_13 I/O Port B data. NC NC
AC10 PORT_B_H I/O Port B H-Sync. NC
AB11 PORL_B_V I/O Port B V-Sync. NC
AA10 PORT_B_CLK I/O Port B clock. NC
AC15 PORT_C_9 I/O Port C data. NC NC
AA15 PORT_C_8 I/O Port C data. NC NC
AB15 PORT_C_7 I/O Port C data. NC NC
Y15 PORT_C_6 I/O Port C data. NC NC
AB14 PORT_C_3 I/O Port C data. NC NC
Y14 PORT_C_2 I/O Port C data. NC NC
Y16 PORT_C_H I Port C H-Sync. NC
AB16 PORT_C_V I Port C V-Sync. NC
AA16 PORT_C_CLK I Port C clock. NC
D11 PORT_D_23 I Port D data. DINB[7] HDMI-B7 DINB[7] IC1905 133pin
5 17
A12 PORT_D_22 I Port D data. DINB[7] HDMI-B6 DINB[6] IC1905 136pin
C11 PORT_D_21 I Port D data. DINB[7] HDMI-B5 DINB[5] IC1905 137pin
B11 PORT_D_20 I Port D data. DINB[7] HDMI-B4 DINB[4] IC1905 140pin
D10 PORT_D_19 I Port D data. DINB[7] HDMI-B3 DINB[3] IC1905 141pin
A11 PORT_D_18 I Port D data. DINB[7] HDMI-B2 DINB[2] IC1905 142pin
C10 PORT_D_17 I Port D data. DINB[7] HDMI-B1 DINB[1] IC1905 143pin
B10 PORT_D_16 I Port D data. DINB[7] HDMI-B0 DINB[0] IC1905 144pin
D13 PORT_D_15 I Port D data. DINB[7] HDMI-G7 DING[7] IC1905 123pin
A14 PORT_D_14 I Port D data. DINB[7] HDMI-G6 DING[6] IC1905 124pin
C13 PORT_D_13 I Port D data. DINB[7] HDMI-G5 DING[5] IC1905 112pin
B13 PORT_D_12 I Port D data. DINB[7] HDMI-G4 DING[4] IC1905 126pin
D12 PORT_D_11 I Port D data. DINB[7] HDMI-G3 DING[3] IC1905 129pin
A13 PORT_D_10 I Port D data. DINB[7] HDMI-G2 DING[2] IC1905 130pin
C12 PORT_D_9 I Port D data. DINB[7] HDMI-G1 DING[1] IC1905 131pin
B12 PORT_D_8 I Port D data. DINB[7] HDMI-G0 DING[0] IC1905 132pin
D15 PORT_D_7 I Port D data. DINB[7] HDMI-R7 DINR[7] IC1905 110pin
A16 PORT_D_6 I Port D data. DINB[7] HDMI-R6 DINR[6] IC1905 111pin
C15 PORT_D_5 I Port D data. DINB[7] HDMI-R5 DINR[5] IC1905 112pin
B15 PORT_D_4 I Port D data. DINB[7] HDMI-R4 DINR[4] IC1905 113pin
D14 PORT_D_3 I Port D data. DINB[7] HDMI-R3 DINR[3] IC1905 116pin
A15 PORT_D_2 I Port D data. DINB[7] HDMI-R2 DINR[2] IC1905 117pin
C14 PORT_D_1 I Port D data. DINB[7] HDMI-R1 DINR[1] IC1905 118pin
B14 PORT_D_0 I Port D data. DINB[7] HDMI-R0 DINR[0] IC1905 119pin
C16 PORT_D_DE I Port D DINEN data enable DINEN IC1905 1pin
D16 PORT_D_H I Port D H-sync. HDMI_HS IC1905 2pin
A17 PORT_D_V I Port D V-sync. HDMI_VS IC1905 3pin
B16 PORT_D_CLK I Port D clock. DINCK IC1905 121pin
T22 PORT_E_9 I/O Port E data. NC NC
T20 PORT_E_8 I/O Port E data. NC NC
U23 PORT_E_7 I/O Port E data. NC NC
V23 PORT_E_3 I/O Port E data. NC NC
T21 PORT_E_CLK I/O Port E data. NC NC
N20 PORT_F_9 O Port F data. FRCI_7 FRCI_7 IC3301 13pin
P23 PORT_F_8 O Port F data. FRCI_6 FRCI_6 IC3301 12pin
R23 PORT_F_4 O Port F data. FRCI_2 FRCI_2 IC3301 4pin
R20 PORT_F_1 O Port F data. NC NC
T23 PORT_F_0 O Port F data. NC NC
N21 PORT_F_CLK O Port F clock. FRCCK1_A IC3301 14pin
G22 PORT_G_9 I Port G data. FRCO_7B FRCO_7B IC3301 44pin
H23 PORT_G_8 I Port G data. FRCO_6B FRCO_6B IC3301 45pin
J23 PORT_G_4 I Port G data. FRCO_2B FRCO_2B IC3301 55pin
J20 PORT_G_1 I Port G data. NC NC
K23 PORT_G_0 I Port G data. NC NC
G23 PORT_G_CLK I Port G clock. FRCCKO_B IC3301 36pin
D19 P29 I CPU I/O PORT HDMI_INT (from IC1905) HDMI_INT IC1905 104pin
C19 P28 I CPU I/O PORT HOTP_CONT1 (to EXT5) HOTP_CONT1 SC1901 18pin
B19 P27 I CPU I/O PORT HOTP_CONT0 (to EXT5) HOTP_CONT0 SC1901 19pin
A19 P26 O CPU I/O PORT POWER_ERR (to power-unit) POWER_ERR SC1702 6pin
5 18
C20 P25 I CPU I/O PORT BL_ERR (from INV) BL_ERR P1701 5pin
B20 P24 I/O CPU I/O PORT DTM_IRQ NC DTM_IRQ P2702 22pin
A20 P23 I CPU I/O PORT CEC_IN (to IC2701) CEC_IN IC2701 6pin
B21 P22 O CPU I/O PORT AVLINK,2_OUT (from Q2702) AVL2_OUT Q2702
A21 P21 I CPU I/O PORT AVLINK2_IN (to Q2711) AVL2_IN Q2711
A22 P20 O CPU I/O PORT PCON2 (to power-unit) PCON2 SC1702 2pin
A23 P19 O CPU I/O PORT PCON1 (to power-unit) PCON1 SC1702 1pin
B22 P18 O CPU I/O PORT AVLINK1_OUT (to Q***) AVL1_OUT Q***
B23 P17 I CPU I/O PORT AVLINK1_IN (from Q***) AVL1_IN Q***
C21 P16 O CPU I/O PORT FPGA_SDE (to IC1710) FPGA_SDE IC1710 66pin
C22 P15 O CPU I/O PORT FPGA_SDA (to IC1710) FPGA_SDA IC1710 67pin
C23 P14 O CPU I/O PORT FPGA_SCK (to IC1710) FPGA_SCK IC1710 64pin
D20 P13 O CPU I/O PORT FPGA_SDA0 (to IC1710) FPGA_SDA0 IC1710 69pin
D21 P12 O CPU I/O PORT FAN_ERR (to power-unit) FAN_ERR SC1702 7pin
D22 P11 O CPU I/O PORT MUTE_SP (to Q1101/2) MUTE_SP SC2703 19pin
D23 P10 O CPU I/O PORT SV1JSW (IN3SW to IC1201) SV1JSW SC2703 20pijn
E20 P9 O CPU I/O PORT STBY_POW (to key-unit) STBY_POW P2302 3pin
E21 P8 O CPU I/O PORT CEC1_OUT (from IC2701) CEC1_OUT IC2701 13pin
E22 P7 O CPU I/O PORT LED_POW_G (to R/C-unit) LEDPOWG P2303 5pin
E23 P6 O CPU I/O PORT LED_POW_R (to R/C-unit) LEDPOWER P2303 6pin
F20 P5 I CPU I/O PORT NVM_CE_N (to IC3503) NVM_CE_N IC3503 32pin
F21 P4 O CPU I/O PORT HDMI_RESET (to IC1905) HDMI_RST IC1905 112pin
F22 P3 O CPU I/O PORT LCD_POW (to power-unit) LCD_POW SC1702 8pin
F23 P2 I CPU I/O PORT RXD (to RS232C-driver) RXD IC2301 15pin
G20 P1 O CPU I/O PORT TXD (to RS232C-driver) TXD IC2301 13pin
G21 P0 O CPU I/O PORT IRIN (to R/C-unit) IRIN P2303 4pin
U12, U16 VDDA18_ADC S Analog Supply power for ADC (1.8V) BU+1.8V
U14, T17 VDDA33_ADC S Analog Supply power for ADC (3.3V) BU+3.3V
K17 VDDA33_CADC S Analog Supply power for CADC (3.3V) BU+3.3V
N17 VDD_PLL S Analog Supply power for PLL (1.8V) BU+1.8V
U7 VDDPLLVDS S Analog Supply power for LVDSPLL (1.8V) BU+1.8V
M7, J7, VDDD S Core supply power (3.3V) BU+3.3V
U8, G12,
G13, L17,
M17
N7, U10 VDDP S Pad supply power (3.3V) BU+3.3V
G10, VDDPSD S DRAM interface supply power (2.5V) BU+2.5V
G11, K7,
L7
P7, U9 VDDLVDS S LVDS supply power. (3.3V)
U11, U15 VSSA18_ADC S Analog ground for ADC. GND
U13, U17 VSSA33_ADC S Analog ground for ADC. GND
J17 VSSA33_CADC S Analog ground for CADC. GND
P17 VSS_PLL S Analog ground for PLL. GND
N14, P10, VSS S Core & pad supply ground. GND
P14, N14,
M14, L14,
K14, K13,
T7
K10, L10, VSSPSD S DRAM interface supply ground. GND
K12, K11,
M10
W20 NC Not connected. NC
5 19
9. IC3702: VHiAK4363VF-1Y
STEREO CMOS D/A CONVERTER
5 20
10. IC4203: RH-IXC100WJZZ
16Mbit Flash Memory

1-9, 16-25, 48 A0-A19 I Address Inputs
29, 31, 33, 35, 38, 40, 42, 44 DQ0-DQ7 I/O Data Inputs/Outputs
30, 32, 34, 36, 39, 41, 43 DQ8-DQ14 I/O Data Inputs/Outputs
45 DQ15A-1 I/O Data Input/Output or Address Input
26 E I Chip Enable
28 G I Output Enable
11 W I Write Enable
12 RP I Reset/Block Temporary Unprotect
15 RB O Ready/Busy Output
47 BYTE I Byte/Word Organization Select
37 VCC Supply Voltage
27, 46 VSS Ground
10, 13, 14 NC Not Connected Internally
5 21
11. IC4401: VHILCX245FT-1Y
Bus Tranceiver

1 DIR I Directory.
2 A1 I/O A-Bus. Output/Input Terminal A1.
10 GND Ground
11 B8 I/O B-Bus Input/Output Terminal B8.
14 B5 I/O B-Bus Input/Output Terminal B5
19 OE I Output enable.
20 VCC Power Source.
5 22
12. IC4402, 4405: VHILCX573FT-1Y
Octal D-Type Latch

1 OE I Output Enable.
2 D0 I Data Input D0.
10 GND Ground.
11 LE I Limited Enable.
12 Q7 O Data Output Q7.
5 23
13. IC4404: VHILCX244FT-1Y
Bus Buffer

1, 19 OE1, OE2 I 3-STATE Output Enable Input 1 and 2
2, 4, 6, 8,11,13, 1A1-1A4 I Data Inputs 0-7
15,17 2A1-2A4
9, 7, 5, 3,12,14, 1Y1-1Y4 O Data Outputs 0-7
16,18 2Y1-2Y4
10 GND Ground.
5 24
14. IC4801: VHiTPS40055-1Y
DC/DC Converter
15. IC4802, IC4803: RH-iXA552WJZZY

Chopper Regulator
5 25
16. IC5801: RH-iXB857WJZZQ
FRC
17. IC6004: RH-iXA361WJZZY

DDR Termination Regulator
5 26
18. IC6001, IC6002, IC6003: RH-iXB822WJQZQ
128M-SDRAM
5 27
19. IC6211, IC6212: VHILVD1023-1Q
LVDS Transmitter

70, 71 TA1+, TA1- The 1st Link.
68, 69 TB1+, TB1- The 1st pixel output data when Dual-Link.
64, 65 TC1+, TC1- O
58, 59 TD1+, TD1-
56, 57 TE1+, TE1-
62, 63 TCLK1+, TCLK1- O LVDS Clock Out for 1st and 2nd Link.
52, 53 TA2+, TA2- The 2nd Link.
50, 51 TB2+, TB2- These pins are disabled when Single Link.
46, 47 TC2+, TC2- O
40, 41 TD2+, TD2-
38, 39 TE2+, TE2-
44, 45 TCLK2+, TCLK2- O Additional LVDS Clock Out. Identical to TCLK1+,-. No connect if not used.
87 - 84, R19 - R10 The 1st Pixel Data Inputs.
81 - 76 R1 [9:0]
99 - 95, G19 - G10
I G1 [9:0]
92 - 88
112 -110, 108 - B19 - B10
B1 [9:0]
106, 103 - 100
124 - 115 R29 - R20 The 2nd Pixel Data Inputs.
R2 [9:0]
136 - 127 G29 - G20 I G2 [9:0]
6, 5, 2, 1, B29 - B20 B2 [9:0]
144 - 139
17, 18 CONT11, CONT12 CONTROL Data Inputs.
I
19, 20 CONT21, CONT22
9 DE I Data Enable Input.
8 VSYNC I Vsync Input.
7 HSYNC I Hsync Input.
15 CLKIN I Clock Input.
21 R/F I Input Clock Triggering Edge Select.
H: Rising edge, L: Falling edge
22 RS I The use of these multi-function depends on input voltage of RS pin.
Input voltage of LVDS output Swing TTL/CMOS Input
RS pin Control VIH/VIL Control for Small Swing
Input
VCC Normal Swing VIH/VIL is fixed
0.6 - 1.4V VOD=350mV (typ) Support Small Swing Input VIH/
VIL depends on input voltage of
RS pin See VIH/VIL Spec
GND Reduced Swing VIH/VIL is fixed
VOD=200mV (typ)
24 MAP I LVDS mapping table select.

H: Mapping Mode1
L: Mapping Mode2
25, 26 MODE1, MODE0 I Pixel Data Mode.
MODE 1 MODE 2 MODE
L L Dual Link (Dual-in/Dual-out)
H L Dual Link (Single-in/Dual-out)
L H Single Link (Dual-in/Single-out)
H H Single Link (Single-in/Single-out)
27 MODE2 I Distribution, DDR function enable.

The use of these multi-function depends on the setting of MODE<1:0>.
MODE<1:0>=HH (Single-in/Single-out Mode)
H: Distribution function enable.
L: Distribution function disable.
MODE<1:0>=HL (Single-in/Single-out Mode)
H: DDR (Double Edge input) function enable.
L: DDR (Double Edge input) function disable.
30 /PDWN I H: Normal operation,
L: Power down (all outputs are Hi-Z)
5 28
31 PRBS I PRBS generator is active when MODE <1:0> = LL (Dual-in/Dual-out mode)
H: PRBS generator is enable. Pattern is PRBS-23.
L: Normal Operation
10, 11, 12, 16, 28, Reserved I Must be tied to GND.
32
23 Reserved I Must be Open.
29, 33, 109 N/C Must be Open.
3, 13, 82, 93, 104, VCC Power Supply Pins for TTL inputs, output and digital circuitry.
113, 125, 137
4, 14, 83, 94, 105, GND Ground Pins for TTL inputs, outputs and digital circuitry.
114, 126, 138
43, 49, 55, 61, 67 LVCC Power Supply Pins for LVDS Outputs.
37, 42, 48, 54, 60, LGND Ground Pins for LVDS Outputs.
66, 72
35, 74 PVCC Power Supply for PLL circuitry.
34, 36, 73, 75 PGND Ground Pin for PLL circuitry.
20. IC6281, IC6282: VHILVD104S-1Q

LVDS Receiver
5 29

50,49 RA+,RA- I
52,51 RB+,RB- I
55,54 RC+,RC- I LVDS data In.
60,59 RD+,RD- I
62,61 RE+,RE- I
57,56 RCLK+,RCLK- I LVDS Clock In.
40, 41, 42, 43, RA6-RA0 O
45, 46, 47
32, 33, 34, 35, RB6-RB0 O
36, 38, 39
22, 24, 25, 26, RC6-RC0 O
CMOS/TTL Data Outputs.
27, 28, 29
14, 15, 17, 18, RD6-RD0 O
19, 20, 21
6, 7, 8, 10, 11, 12, RE6-RE0 O
13
3 PD I Power down and Output Control.
H: Normal operation.
L: Power down
4 OE I Output Enable.
H: Output enable
L: Output disable.
2 DK I Output Clock Delay Timing Select.
tRCP = Output Clock Cycle.
L: Offset 0[nsec]
M: Offset - 3 tRCP (typ) [nsec]
14
H: Offset + 3 tRCP (typ) [nsec]
14
5 R/F I Output Clock Triggering Edge Select.
H: Rising Edge
L: Falling Edge
9, 23, 37, 48 VCC Power Supply Pins for TTL outputs and digital circuitry.
31 CLKOUT O Clock out.
1, 16, 30, 44 GND Ground Pins for TTL output and digital circuitry.
53 LVCC Power Supply pin for LVDS inputs.
58 LGND Ground Pin for LVDS inputs.
64 PVCC Power Supply Pin for PLL circuitry.
63 PGND Ground Pin for PLL circuitry.
5 30
21. IC6341: RH-iXC029WJQZQ
FPGA
5 31
22. IC6342: RH-IXC030WJQZ
PROM

2 DATA O The DATA output signal transfers data selially out of the serial configuration device to the FPGA during
read/configuration operation.
During a read/configuration operations, the serial configuration device is enabled by pulling nCS low.
The DATA signal transitions on the falling edge of DCLK.
5 ASDI I The AS data input signal is used to transfer data serially into the serial configuration device.
It receives the data that should be programmed into the serial configuration device.
Data is latched in the rising edge of DCLK.
1 nCS I The active low chip select input signal toggles at the beginning and end of a valid instruction.
When this signal is high, the device is deselected and the DATA pin is tri_stated.
When this signal is low, it enables the device and puts the device in an active mode.
After power up,the serial configuration device requires a falling edge on the nCS signal before begin-
ning any operation.
6 DCLK I DCLK is provided by the FPGA.
This signal provides the timing of the serial interface.
The data presented on ASDI is latched to the serial configuration device, at the rising edge of DCLK.
Data on the DATA pin changes after the falling edge of DCLK and is latched into the FPGA on the
rising edge.
3, 7, 8 VCC Power pins connect to 3.3V.
4 GND Ground pin.
5 32
CHAPTER 6. BLOCK DIAGRAM/WIRING DIAGRAM
LC46XL1E
Service Manual
[1] BLOCK DIAGRAM (LC-46XL1E/RU)
BLOCK DIAGRAM (LC-46XL1E/RU)
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
61
[2] BLOCK DIAGRAM (LC-52XL1E/RU)
BLOCK DIAGRAM (LC-52XL1E/RU)
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
62
[3] POWER BLOCK DIAGRAM (LC-46XL1E/RU)
POWER BLOCK DIAGRAM (LC-46XL1E/RU)
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
63
[4] POWER BLOCK DIAGRAM (LC-52XL1E/RU)
POWER BLOCK DIAGRAM (LC-52XL1E/RU)
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
64
[5] WIRING DIAGRAM (LC-46XL1E/RU)
WIRING DIAGRAM (LC-46XL1E/RU)
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
65
[6] WIRING DIAGRAM (LC-52XL1E/RU)
WIRING DIAGRAM (LC-52XL1E/RU)
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
66
CHAPTER 7. PRINTED WIRING BOARD
LC46XL1E
Service Manual
[1] MAIN UNIT PRINTED WIRING BOARD
MAIN Unit (Side-A)
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
71
MAIN Unit (Chip Parts Side-A)
J
R 1807
LUG1701 S C2705 S C2707
P1702
Q1910
Q1909
C1904
R 1909
D1901
D1909
C1903
R 1906
D1902 D1910
LUG1703
TH3001 R 3068
D1908 D1907
C2730
R 1811
C1902
C1901
IC1902
C3044
R 3003
FB2703
R 2771
R 2752
R 2753
C2732
R 2757
IC1901 C2731
D2302 D2301 FB2302
R 2301
FB1901
C2726
R 2307
R 3038 R 2726
D2304 D2303 FB1902 D1903 C2733
P2302
I
FB2301 LUG1705
P2702
R 3018
R 3028
R 3029
R 3030
FB3001
C3001
R 1904
R 1902
R 3051R 3052
R 3008
R 3061R 3062
D1911
R 3046
R 3045
R 3048
R 3049
R 3047
R 3050
R 3053
C1911
P2304
R 3055
R 3063
R 3057
R 3058
R 3056
R 3059
R 3060
R 3069
R 1934
C1910
R 1850
R 1849
R 3005
FB1906
FB1903
FL1902
FL1901
C1976
C1977
R 1862
C1773
C1951
C1952
C1763
R 1700
FB1706 C1777
S C1902
C1935 C1909 C1778
P1701
C1772
LUG1709
C1957 C1947 C1944 C1937 C1926 C1925
C1941
C1939
L1905 IC3001 C1775
C1955 C1948 C1945 C1932 C1927 C1924 R 1927 C1776
C1765
H C1946 C1774
IC1710
L1906 C1780
R 1749 R 1731
R 1925
R 1783 R 1736
R 1714
R 1808
L1907 R 1784 R 1738
C1766
IC3002
R 1924
R 1860
L1908
R 1945
D1913
R 1859
D1912
R 1923
R 3503
IC1905
FL2304
FL2309
R 3519
R 1922
FL2305
R 1901 R 3532R 3541
G R 1903 L1901
R 3550 FL2310
FL2306
R 1921
FL2314
S C2302
FL2311
L1902
R 3510 FL2307
R 3520 FL2312
R 1920
R 3504
L1903 R 3571 FL2308
S C1901
C1953 R 1928 R 1926 FL2313
R 3506
R 3553
R 3593
R 3552
C1954 FL2315 R 2304
R 1940
R 1939
R 1938
C1942
C1943
C1934
R 1933
R 1932
C1929
R 1929
C1923
C1922
L1904 R 3542 R 3543 C3530
R 1935
R 2305
C3548 C3547 C3546 C3545
R 3588 C3557
R 3537 R 2337
R 3594
R 3555
C1961 R 3536 R 3535
X1901 R 2334
F
C2306
R 2313
R 3556 R 3538
R 3540
S 3501
R 3546 R 2330
R 3508
R 3547
IC3503
C3515
R 3310
R 3539
R 3507
R 3597
R 3306 C3510
C3525
R 3522
C3507 R 3549 TH3003
R 3308
C3307
R 3307
R 3305
C3007 R 3564
S 3001
Q3501
Q2705
R 3599
C3310
C3312
C3314
C3319
LUG1706
LUG1710
R 3505
R 3524
R 3525
R 3502
D3001
R 3313
Q3504
C3338 C3516
R 3521
R 3514
R 3516
C3522
P3001
R 3318
C3511
R 3531
R 2713
C3301
C3327 R 3566
C3331 R 3529
C3303 C3339 FB3502
Q3503
R 3598
C3337
R 3315
C3551
C3505
C3335
E R 3582
C3559
FB2706 FB3301
IC3501
R 3319
C3302 R 3583
D3501
C2709 FB3302 C3503 C3513 Q3502 R 3565
FB3305
C3332
R 3523
C2705 D2701 C3341
R 3316 R 3567 R 3515C3537 R 3568
S C1702
C3340 R 3530
R 3312
FB2707 R 3320 C3558 C3539 R 3513C3564 IC3507
R 3321
C3328
C3561
R 3528
C3523
R 3317 C3540 IC3505
R 2707
R 2709
R 2711
D2705 C3330 C3565 FB2310

C3334 C3524
FB3304
C3336 FB3303 C3562 FB2303
FB2708
C3343
FB3306
C3333
Q2704
C2703 C2707 C3566 C2332

C3342 C1716
P2303
C3329 C3526 C2327
D3301 C3527 C3532
R 3740
R 3739
C3305
D C3501
D2313
D2308 R 2329
R 3302 R 3575
C3306
C1747
FB2306 R 2332
R 3303 R 3744
IC1702
D2307 IC2303 C3550 C3549
R 3743
R 2333
C1704
FB2307 R 2360 Q2307 IC3702
R 2363
R 3748
R 3750
R 3749
D2306 R 2326 R 2362
C2307
R 2335
FB2308 C2318
R 2359
R 2358
FB2304
R 2366
FB2305
D2309
R 3709
R 3711
R 3710
R 3706
R 3736
L1702
R 3732
C3737
R 3745
D2305 Q2305 C3739 C2338
R 2364
R 3703
R 3704
R 3737
C1735
D1707
R 3701
R 1739
R 1740
D2310
R 3717
C3740
C3701
C2308
R 2365
FL2301
C3720 L1703
C FB3703
C3706
R 3718
R 2716
S C1701
R 3705 R 3735
D2312
C3721
C2310
FL2303 D1706
X3701
R 3719
C3722 C1727
C1733
D2311
C2309
FL2302 C3723
C2714
C1721
C3702
C3708
R 3720
Q1703
C3711
R 2712 C3704
R 3721
C1715
C2702 C3724
C1746
C2706 L1701 R 1713
R 1720
C1703
R 1728
C1753
FB2710 R 3722
IC1704
C3725
IC1711
R 2706
LUG1708
C3710
R 3723 C1702
R 3746
R 3747
R 3731
R 3730
R 3727
R 3726
C3709
C3713
C2720
C3712 C3705 C3726

FB2709
C1782
C1744 D1705
B C2708 Q1706 IC1701
FB3702
C3707
C2704 FB3701
R 3729
R 3728
R 1709 R 1852
FB2705
LUG1707 C1720
FB1703
R 1810
FB2716
FB2715
S C2702 S C2703 S C2704 R 1814

LUG1702 LUG1704
A
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
72
MAIN Unit (Side-B)
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
73
MAIN Unit (Chip Parts Side-B)
J R1816
C2328
R2383
R2385
Q2311
FB2712 R2316
C2740
IC2307
C2725 R2776 R2384
R2380
FB2701 FB2309 R2382
FB2702
L2703
C2741
C1907
R1916
C2329
R2310
C2301
Q2310
R2736
R2702 C1908
D2316
R1914 IC1903 R1913
Q1905
D1904
R2343
Q3001
IC1904 R1915
C2734
TH3002
R3039 C3005
C2324
C2330
C2331
R3037
R3036
IC2701
R2303
R2312
R1908
R1907 R1917
IC3003
R3044
D2315
C2323 R2376 Q1907
C1906
C2322
C2325 R2309
R2342
R2396 C1905 IC2301
R2381
R2397 C1711
D1905
Q2301
Q1903 Q1901 Q1904 Q1902
I R1911 R1912
D2314
R2374
R2371
R2314
R2311
C2739
R3024
R2386
C2302
C2303
C2304
C2305
D2317
D2319
D2318
R1712 X3001
R2328
R2323
R2327
R1794 R1809
R1793 Q2710 Q2709
R3004
Q3003 Q3004
R3043
R1792
Q1704 R1796 R3010 R3015
R3023 R1797 C3034
FL1905
FB1909
FL1904
FB1908
R1831
C1978
R2320
R1805
IC2302
C3039
R1775
R1773
R3020
R1832 R1717 R1847
R1833 R1718 R3042
R3032
R3033
R3031
R1834 R1715 C1759
R3070
R1751
C3032
R1780
C1784
C1963 C1959
C1758
R1782
R1798
R1795
R3011
IC1705 C1757
R3064
R1835 R1730
R3019
C3022
R1774
FB3009
R1836 C1760 R3012 C1962 C1960
C1742
R1837 R1781 C3040 R1931
R1861
R1762 R3025
R1711
C1783
H R1838 C1767 C3038 C3002
R2317
C1779
C3029
C3010
C3015
C3030
C3031
R2308
C1928
R1930
C1743
R1750 R1777 R1776 C3035 R1918
Q1908
R2318
FB2713
C1741
C1918
R1800
D1906
R1839 R1856 R1846 R1845 C1768
R1910
C3028 C3041 R1905
R1840 C3023
C3036
R1786 C1930
C1739
C1761
R1716
IC1709
FB3006 Q1906
R1756
R1848
C3042
C3046
C3048 C1975
R2321
R2319
R2306
FB3008
R1785 C3016 C1917
C3026
C3033 C3047
C1745 C1931
C3024
R1763
C3020
FB3014 C3012
C1762 R1799 FB3010 C1974
Q2303
Q2302
C1916
C3027
FB3007
C3037
C3011 C3008
C1973
C1972
FB3002
C1915
C3050
C3049
R3007
C3021
C3018
C3025
C3003
C1970
C1971
C3013 C3017
R1764 C1969
R3517 C1914
R1787 R3551
FB3005
C1764
R1788 C3004 FB1707 C3019 R3511 R1919 C1968
G R1789
C1919
C1921
C1967 C1964
C1966 C1965
FB1905
FB1904
R1790
R3002
R3035 C1913
R1791
R3509
C1912
R1941
R1942
C1979
R1937
R2367
R1936
R3554
R3595
R3040
R3041
C1950 C1956
C1933
C1936
C1938
C1940
R3544 R3545 C3529 C1949 C1958
C3533 R3589
C3556 R3590
FB3503 C3543 C3544 C3541 C3542
C3534
R3563
R3548 X3301 C1920
FL1903
FB1907
R3534 R3533 R3592
R3591
R2302
F
C3519 C3517 R3558 R3309
C3315
R3311
R2348
R2346
R2344
R2369 C2320
R3559 R3314 C3318
R3512
IC3504
R3562
R3557
C3528
C3508
C3509
C2312 R2349 R2338

FB2714
C3520 C3518 C3304
C2313
R3021
IC2304
R3026 R3027
R3526
R3527
C3325
R3014 R3065 Q3005 Q3002
R3066 R3009
R1778
R1752
R1857
R1858
R3067 R3001 C3512

FB3004
C3521
C3567
C3506 C3324
R2340
R2336
C2311
R3016 C3006
C3009 R3581
E
IC3502
R1722 C3536 R3580 C3321
R1806 R3006 C3045 C3504 C3514
R1727 R3570
R3569 C3538
C2316
IC3301
Q2308
IC3004 IC3005 FB3501

IC3506 C3326
R2402 IC2305
R3560
R2372
Q2309 C3043
R2415
R2399 R2406 R2400
R2353 R2351
R1705 Q2312 C3014
C2326
R1704 C3535 C3502
C3560
C2314
R2341
R2331
C2333 C3568
C3563
C3531
C3323
R2355
R2354
R2339
C2336
Q2313
C2334
C3569
R3304 C2315
Q1702
R2347
R2345
R2352
C2335 R2410 D1703 C1709
C3322
R1710
D R1725 R3501 R3518

Q2315
Q2314
R1703
D1701
C2337
C2319
R2370
R1759 C1705 C3552 C3553 C3554 C3555

R2414
R2403 R2401
R1804 R1729
R2417 R2416 FB3704 FB3705
R2368
R1706 C1737
C3320
R1761
C3317
C3316
C3313
C3311
C3309
C3308
Q2306
C1713 R1726 C1734 C1732 C3735 C3736 R3301
R3742
R3751
R2350
R2357
R1707 Q3702 Q3703
Q1701
R1702
R1708
C1701
R1743
R1701 FB1702 R1803
IC1708
R2356
R2361
Q2304
IC2306
D1716 R1755 R3738 C2321
C3738
C3741
C3742
C1749
D1708
C1736
R1769
C1750
R1770
C1751
C3719
R3716
R3702
R3733
C1738 C3703
C1729 R1754
C1730
Q2707
R1801
R2315 C2317 R2721
R1768
R2719
C1771
R1744
C1769 R1753 R3734 C2719 R2322
Q2708
R1741
C1726
C1728
R1742
R1779 IC1707
C
C3718 R3708 C3717

IC1712 R1767
C1748 R2325
D1714
C2723
IC2704
C1740
C1752
R2324
R1802
C1710
IC3701
C1718
C1722
R1746
R1747
R1748
C1725
C1731
D1709
IC1706
C1723 R1733
D1713
R1853
R1765
R1766
C3716
C2718
R2715
C2722
R2720
R1854 R1737
R1745
D1715
C3715
Q2703
FB1701
C1714
C1717
D1704
C1756 C3714
R1760
C3745
C3746
R3753
FB1705
C1755
R1719
R1721
C1770
R1723
C1708
R1758 C1724 D2704
R1771 C1706
C1712
D1702
R2708
R2710
L3701
B R1842 C2721
R3724
C3727
R3725
C3728
C3729
C3730
C3731
C3732
C3733
C3734
C3744
C3743
R1757
R2743
R1724
R1772
C1754
C1707 D2703
R1851
R1734
C2717
IC1703
Q2713
R2739
R2740
R2774
R2747
C2728
C1719 C2724
R2745
Q2711
R2738 R2737 R2749 Q2706

R1735
C2715
C2711
R2717 C2710
R1732 C2713 FB2711
R2748
R2751
R2750
R2741 R2714
FB1704
R2746 C2716
Q2702
Q2701
Q2712
R2701
C2727
D2706
R2758 R2704 Q2714
C2701 R2744 R2742
R2705
Q2723
R2773
R2703
C2729
D2708
Q2715
D2702 C2712
Q2716
R2775
Q2717
A D2707 R2754
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
74
[2] AV UNIT PRINTED WIRING BOARD
AV Unit (Side-A)
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
75
I
J
C
D
H
A
B
G
1
2
3
R1126
R1137
AV Unit (Chip Parts Side-A)
R1204
4
C352
C355
LUG301
C354
C350
R349
R350
D1125
R1201
Q306 C353
C351
D1113
C1213 C1209 C1226 C1227 R1103
C1201
FL1211
Q305
C1215
FB1202
FB1201 D1101
C1159
FB1203
FB1204
C1207
C1114
R1102
FL1212
5
C1204 FB1103
R1130
C1210 D1106 C1150 R1127
LUG302
R1213
C1216
R348 R1138
R1210 R1206 R1220 R1223 C1162 IC1102
R351
R346
R1209 C1142 C1161
R1212 R1215 C1224 C1225 FB1111 R1177
C1134 C1160
R1119
R1216 R1219
FB1101
C1211 C1217 C1208 C1127 R1153
R1225
C1145
R352 R347 C1157
C1205
R1155
Q1107
C1143
6
D1121
C1139 R1149
R1112
R1211
R1214
C1222
C1223
R1124
C1115
C348
FL1107
R1228
R1203
FB1109 R1146 C1146 C1158
D1102
Q1204
FL1108
D1112
R1152
D1114
C1202
C1105
C349
D1201
R1227
C1203 C1140 R1151 R1156
R1110
C1154
R1226
C1212
C1218
C1144
Q1106
Q1105
FB1110 R1148
IC1201
Q1108 C1104
R1113
C1220
C1221
R1160
R1159
C1206 R1157
Q1203
D1108
7
R1202 C1253
R1158
C1109
D1117
R327
C311 R1217 R1221 R1161 D1111 FL1106
D1115
R1224
R318
C1111
C360 FL1109 R1115 C1106 D1122 R1118
R1218
R1222
Q1201
Q1202
C319
R322
C1155 C1138
R321
C318
8
IC303
R1154
R1125
R1116
C1156
Q301
C317
C1128
R1179
FB1112
R319 C306 C1135

C1107
C316
R320
R310 C301 FL1110 R1120 C1149 R1129
D1123
C1129
R307
R302
R311
R301
C320 C321
R1128
9
C302 D1105
C307
C1116
FB1104
C1118 FB1105 FB1107

FL1103
FL1102
FL1101
R1135
R325
FL1105
FL1104
R326
R1136
Q302 R306 D1104
R362
R328 R1123 R1114 R1122
R1147
R1134
C1117
D1103
D301 C1119 R1121

C1214
R1108
R1101
R1150 C1120 C1113

R1106
FB1108
FB1106
R1117
C1121
R1104
C347 C1112
D1124
10
FB1102
C1251
C336 C344 C324 R1173

D305
D303
R1111
R364
C1123 C1122 C1124 C1153 C1103

C1110
R1105
C1152
C1151
C1101
R345
R341
R342
R344
R333
R332
D1120
76
D1118 D1116
R1132 C1102
R1107
R1109
C1252
C1219
D304
C1125
R1143
D1109
C361
C337 C345 C325 C346 D1110
11
C1132 C1136
C1131
D1107
D1119
C1126
FB1218
FB1213
R1139
Q1103
R1140
C1108
R365 R1133
C1130
D302 R363 C1133 C1137

R339 Q1101 IC1101
R1145
R1142
R1141
R1144 Q1102 Q1104

D310
C340 C362
12
D309 C1148
C1147
P301
D315
R324
D307
Q303
D308
R360
C304
C322
13
D314
R303
IC301
R340 Q307 C364

D306
C341
C363
C326
C308
R358 R359
C314
R309
C310
R305
C328
R356 R357
R335
R330
R315
D318
R361
14
R312
C365
R353
R337 D311
R314
C358
C333
C356
C312
C332 R329
R354
15
D317
R323
C303
Q304
C323
D316 R304 C359
D313
IC302
R331
C327
C305
C329
R336
C315
R308
C309
16
R355
C357
C335
R317
R313
C366
R334 R338 D312

C334
R316
C313
17
LUG303
R343
LUG304
18
19
AV Unit (Side-B)
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
77
[3] DIGITAL UNIT PRINTED WIRING BOARD
DIGITAL Unit (Side-A)
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
78
DIGITAL Unit (Chip Parts Side-A)
R 4016 R 4711
P4002
R4017
IC4002
R 4012
R 4020
C4781
R 4034
R 4781
R 4705
IC4703
C4782
C4712
R 4712
R 4708
IC4702 R 4709
C4020
Q4702
Q4701
Q4001
Q4002
X4001
R 4782 R 4650
R 4009 C4007
R4718
C4006
C4035
R 4038
C4034
R 4039
R 4021
R 4706
C4703
FB4602
Q4703
C4718
R 4024 C4023 IC4705
C4710
C4010 R 4704 R 4675
C4707
R 4659 R 4616
R 4218
LUG4602
I R 4671
R 4672 R4673
C4623
R 4202
LUG4601
R 4635 C4625 Q4607
R 4631 R4632
C4628 C4627
R 4217
R 4710 R4243
C4203
R 4634
R 4637
R4205
C4634
R 4703
R 4702
R 4701
R 4240
R 4622
C4636
C4639
R 4636
R4213
R4037 C4604
R4236
R4233
IC4701 FB4202
R 4242
R 4191
C4635
R4204
C4205
C4206
R 4190
R 4036 C4702 C4001
C4637
R4623
C4640
R4212
H
R 4196 C4701
IC4001 C4606
R 4221
D4702 C4609
C4706
R 4195 D4701
R 4220
C4641
C4638
R 4624
R 4192
P4003
R 4215
C4601
R4031
R 4194 C4019
L4701
FB4009
R4208
R4030
R4035
R 4216
FB4007
G R 4193 C4032
C4033
R 4201
R 4197
R 4219
FB4008
C4717
C4715
C4008
R 4207 R 4214 R 4206 R 4211
R 4029
IC4005
R 4026
C4031
C4030 X4002 R 4234
R 4237 R 4238
R 4028
R4244
R4435
R4421
C4201
E
R 4427
R 4412
R 4409
C4408
R 4436
IC4405
IC4406
R 4431
R4415
R 4432
R 4403 R 4401 L4401
R 4428
D FB4403
C 415
C4416
IC4404
IC4401
S C4602
P4001
R 4406
R4417
C4403
C4410
R 4405
C4412
R 4422
C4406
R 4416 R 4414
R 4413
R 4441
R 4411
IC4402
R 4410
R 4437
C4421
C R 4426 C4401
P4004
C4407
R 4429 C4420
LUG4604
LUG4603
A
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
79
DIGITAL Unit (Side-B)
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
7 10
DIGITAL Unit (Chip Parts Side-B)
R4605
R 4604
R 4603
R 4602
R 4645 R 4633 C4029
R 4638
R 4601
R4630
R 4629
C4630
C4629
C4631
S C4601 IC4003
R 4714
R 4713
IC4204
C4208 R 4250
R 4246
R 4647 R 4646 C4210
I R 4648 R 4245
R 4607
R 4609
R 4608
R 4643
R 4644
R 4606
R 4658
R 4657
C4711
R 4249
C4709
R 4649
C4708
R 4203
FB4005
R4674
FB4701
C4621
FB4002
C4011
C4009
R 4642
R 4011 R 4004
R 4225
FB4601 C4022
C4633
R4640
R4651 R 4229
R 4223
C4704
R 4707
C4705
C4617 C4614 C4611 R 4619 R 4665
R 4002
C4005 C4003 C4021 R4007

C4004 C4002
C4028
R 4010
FB4001
R 4661 R 4228
C4025
R4666
IC4604 R 4227
R 4235
L4603 IC4201
C4605
R 4617
C4607
Q4602 Q4601 R 4626
C4603 L4601 R 4001 C4027
R 4639
C4632 R4641
R 4662 R4239
R4612 R 4660 R 4013
FB4003
C4624 C4608 R 4025
R 4652
R 4613
H C4618 C4615 C4612 R 4620 R 4667 C4610 R4627
R 4618
R4033
R4032
R 4668
R 4628 C4626
L4604
Q4604 Q4603 IC4601
R 4614
R 4615
R 4663
R4003
R4005
R4008
R 4222
R 4006
R 4027
C4619 C4616 C4613 R 4621 R 4669
R 4610 R 4611
R 4670
L4605 C4622 C4602
Q4606 Q4605
FB4004
C4018
R 4664
R4014
R4015
FB4603 C4015
IC4704
C4024
C4016
C4017
R 4251
FB4006
G R 4210
R 4018
R4716
R4715
C4013
C4014
C4026
R 4209
C4012 R 4019
D4703
R 4241
R 4404 R 4402 R4407 R4408
IC4202 R 4 717
C4713
C4716
R 4230
R 4224
C4714
R 4231
R 4232
IC4203 R 4226
F
R 4440
C4209
R 4248
FB4201
R4247
R 4418
C4414
C4202
C4204
C4207
E Q4201 R4434
07
IC4407
R4433
C4409
C4413
R4420
R 4419
C4404
R 4424
R 4438
R4447
C4411
FB4402
IC4408
IC4403
D
C4405
R 4430 R4425
R 4423 C4417
Q4401
R 4446
C4418
R 4445
C4419
R 4442 R4443
IC4409
Q4402
R 4444
R 4439
C FB4401
C4402
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
7 11
7 12
19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
(Chip Parts Side-B) (Chip Parts Side-A) A
D-TUNER Unit D-TUNER Unit (Side-B) D-TUNER Unit D-TUNER Unit (Side-A)
LUG202
LUG201
B
R209 C241
C205
C278
D201
C208
R204
R202
C277
FB201
Q212
C204
IC203
R203
C255 R201
C
R271
R207
C202
C201
Q209
R292
D207
R293
C274
R208
C203
R291
R246
C275 R214 R206
Q211
C206 C256
L212
R295
C279
C216
R250
IC209
IC204
D
R259
R205
R294
R224
R219
C215
C234
D204
R241 C217
L203
R242
R237
D203
FL201
Q203
R286 C227 R223
C233
C223 R230 R236
R243
R239
Q210
C222 C230
R238
R288
D206
C231
E
C228
R287 IC201
R227
C218
D205
FL202
C220
C276
R226
C224
C219
C221
R228
R233
R229
R232
C225
L204 C232
R235
C268
R231
L205
R240
C226
F
C246
C229
Q204
R244
IC207
R234 C265 C209 C210
R211
IC208
IC205
R251
Q205
IC206
C245
C266
C269
C263 C207
R264
R265
R263
C267
G
R252
R249
L206
L201
C235
L202
C214
C211
C236
C244
L208
C257 C258
C260 C248
C239
C238
X202
C240
C242
H
R210 C261 C243 C251
L207
R215
R212 C252 C254
C262 C259
C213
C253 R213
C212 C250
C264
R216
R217 IC202
C237
C247
R218
R220
R248
C249
I
LUG203
R221
R245
R225
R222
R247
J
[4] D-TUNER UNIT PRINTED WIRING BOARD
[5] KEY UNIT PRINTED WIRING BOARD [6] R/C, LED UNIT PRINTED WIRING BOARD
J J
P101
D155
I I
S157
C107
H H
P151
RMC101
SLD101
G G
S153
R101
R132
D101
IC101
C104
F F C105
C102
R135
R136
R117
Q105
Q104
R138
S151 R110 R105
R102
D103
R137
E E R108
Q103
R109
D151 R106 R104 R107
Q102
R151
R152
R123
S152
D114
Q106
D D
R121
R126
D113
Q107
R111 R124
S154 R112
D115
R122
C R114
C
R113 R127
D152
R153
C106
S155
J101
B B
R115
3
A
KEY Unit (Component Side) KEY Unit (Chip Parts Side) A
R/C, LED Unit (Component Side) R/C, LED Unit (Chip Parts Side)
1 2 3 4 5 6 7 8 9 10 2 3 4 5 6 7 8 9 10
1
7 13
[7] ILLUMINATION UNIT PRINTED WIRING BOARD
I ILLUMINATION Unit (Side-A)
E
ILLUMINATION Unit (Side-A Chip)
7
D901
6
4
ver1
D 5
R 902
Q901 R 901
3
P 901
1 2 3 4 5 6 7 8 9 10
7 14
[8] FRC UNIT PRINTED WIRING BOARD
FRC Unit (Side-A)
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
7 15
FRC Unit (Chip Parts Side-A)
C6120
TL4801 TL4803 TL4802
LUG4801 C6121 P5802 LUG4803
7 P5801
R6092
C6119
R6036
3
C6118
6
C6015
C6020
C6133
C6117
C6116 R6037
H C6132 C4817 C4804 C4806
R5916
R5930
R5931
R5932
R5917
R5915
R5914
R5913
FB6005
C6018 R6038
FB6006
C6131
R6035
C6130
R6085
TL5811
C6012
C6011
R6102
R6101
C6099 C6097
R6108 R6104 R6103 TL6004R6095 R6064 R6063 C4818
R6121
R6062
R6061
C6098 C6096
C6016
TL6015 R6119TL6007
C6021
R6087 R4826 R4831
C5892
FB5803
Q4803
FB6007
TL6012 C4819 FB4802
C6013
C6019
FB4806
C6014
R6068
R6057
R6042
R6031
L6234 TL6001 L4802 L4803
TL5814
C6233 FB4805
L6233 R6137 IC6003 R6139 R6132 IC6002 R6135 TL5810
C6234 R6138 R6140 R6131 R6133
G L6232
P4801
L4801
R6070
R6055
R6044
R6029
R4814
L6231 TL6014
C6003
C5890
C6001
L6230 TL6003
FB5802
C6235 TL6013 TL6005
L6229 C6236 R4815
FB6003
R6136
R6074
R6066
R6059
R6130
R6048
R6040
R6033
C6002
R6072 R6076 R6078 R6053 R6046 R6050 R6052 R6027
SC6212
L6228 R4816
TL5813 C4805 C4807
FB6008
L6227
TL6006
L6226 C6237 FB6001
FB6348
C6238
L6225
L6224
TL6002
F L6223
R6373
R6374
TL6211 R5865 TL6020 R6352 R6349 R6348 R6347 R6346 R6345 R6343 TL6023
TL6362 TL6361
R6364 R6353 R6354 R6355 R6356 R6357 R6358 R6359 R6360

R6220 TL5819
R6222
R5899
R5898
R5881
R5880
R5869
R5906
R5890
R5859
R5802
P4802
TL5820
FB6347
R6230 R6224
R6342
L6341
TL6356
TL6360 X6341
C6268
R6341
FB4804
FB4803
C6341
C6342
E IC6341
TL6354
TL5818 TL6357
R6284 R6283
L6222
C6261
TL6352 TL6353 TL6022

C6262
L6221 TL6021
R6363
R6362
R6361
L6220
R6286
IC5801
R6382
R6383
L6219
R6288
D R6290
L6218 R6294
C6263
R6292
C6264
R6296 IC6282
FB6004
L6217
R6298
R6332
TL5827
SC6211
L6216
R6302
R6300
C6095 C6009
R6123
R6124
R6018 R6016
L6215
R6304
C6094
SC6281
R6308
C6265
C6266
R6020
L6214 TL5830 R6326
R6306
L6213 R6122 R6129
R5811
C6239 R5803 R6022
L6212
R6116 R6117 R6118

C6240
R6287
R6026 R6024
R6285
L6211
R6291
IC6001
C R6289
R6297
TL5821
TL6212 R6293
R5887
R5888
R5842
R5841
R6295
R6301
R6014 IC6281
R5826 R5823 R5819 R5820 R6007 R6331
R6303
R6240 TL5822 R6079
R6299
R6001
R6114
R6305
R6243
TL5829 R6321
R6125
R6126
R6245 R6003 R6005 R6115
R6251 TL5828 R6307
R6315
R6311 R6310 R6309
C5894
1
B
LUG4802 TL5812 FB5801 TL5809 8 C6376 LUG4804
P6341
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
7 16
FRC Unit (Side-B)
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
7 17
FRC Unit (Chip Parts Side-B)
TL5804 TL5816 TL5815
TL5805 TL5803 TL5802 TL5801 9

TL5806 TL5807 TL5808 TL5817
C4816
FB6214
H D4803 D4802
C6267
5
R4812
R4810
R4811
R4808
R4809
R4806
R4807
R4822
C4815
FB6212
4
R4801 FB5817
R6120
R4802
C4811
R6089 R6088
C6189
C6188 C6186 C6083
C4801 C4814
R6134
FB5811 TL6016 FB6213
R4803 IC4801
C6174
C6175
C4813 TL6011 R6100 R6086 TL6019 R6113 C6231 C6229 C6227 C6225
C6058
C6060
C4802
FB5810 R6099 R6084 TL6008 R6112 C6191 C6232 C6230 C6228 C6226
C6187
C6179
C6062
C4823
R4819
Q4802
C6172 C6082 C6190
R6032
C6059
C6057
R6041
R6058
C6087
R6067
C6085
C6178
IC4803
IC4802
C6061
C6086
C6084
C6063
C6064
C5891 C6173
FB6217
C6128
C6199
C6081
TL4807 TL4804TL4811 C4803 C6167 C6129
R4821 C6123 C6088 C6198
C6006 R6110 C6166 C6065 C6122 R6107 R6143 C6200 C6136 R6142
R4827
R4832 R4828
R4825 R4824
R4820
TL4808TL4806TL4805TL4809 C4812 C4820 R6144
C6005 R6109 C6114 C6055 C6056 C6066 R6060 C6201 C6080 C6079 C6090 C6089 C6137 R6065
G C6180 R6039
C6223 C6221 C6219 C6269 C6217

R4823 FB5812
C6050 C6048 C6124 R6106
C6078 C6077
C6224 C6222 C6220 C6270 C6218

FB6009
C6115
C6069
R6030
R6043
R6056
R6069
C6068
C6073 C6074
C6004
C6184 C6071 C6075
Q4801
C4821 C6054 C6053 C6067 C6181 C6092 C6091
TL4815 TL4814 C6164
C6194
C6046 C6127
C6047
C6070 C6141
FB5816
C6076
C6072C6138
TL4817 TL4816 C6052 C6049 C6176 C6185 C6093
C4822 C6165
C4810 C6195
C6169
TL6009
C6183
TL4819 TL4818 C6177
C6051
C6197
C6162
C6126
C6170
C6182
C6140
C6192
C6139
C6196
C6125 R6105
C6193
TL4821 TL4820 R4804
C6168
C6163
C6171 TL6018
TL4823 TL4822
R4805
C4825 C4808 C5889 IC6004
TL4813 TL4812 TL6017 IC6211
FB6341 R6028 R6051 R6049 R6045 R6054 R6077 R6075 R6071
R6047
R6098
R6073
R6141
R6034
R6111
TL4810 TL6010
IC4805
IC4804
C4824
C4809
FB6011
R4813 R4817
R4829 R4818 C6135
C6134
F
R5902
D4801 D4804
TL4827 R5870
TL4834
R5903
TL4833 FB6343 R5904 R5864 R5866 C6212 C6214 C6215
TL6027 R5868
C6211
R6213
C6213
C6216
TL4832 R5860 R5883
TL6024 R6217 R6218
R5905
R5863
TL4831 C6346 R5875
R6379 R5872
R5862
C6371 C6343 R5873 R5878 R6216 R6219
TL4830 C6347 R6378
R5907 R5908
R5861
C6357
TL5824 R5856 R5858 R6212 R6231 TL6218
R5900
R5901
R5874 R6215 R6221
TL4829 C6348 C6362 R5867 TL6217
R6211 R6229
R5855
R5876
C6370 C6375
C6353
TL4828 R6214 R6223 TL6216

C6360
FB6344 R6350 R6228 TL6215

TL4826 TL5823 R5921 R5925 R6225
R6351 R5877 R6227
R5854
R5910 R5871 R5923 R5927 TL6213
R6226
FB5804
R6369
R6372
R6371
R6370
TL4824
R5879
C6345 R6367 R6368 R5909
R6344
C6358 R5922 R5926 TL6214

E C6364
C5887
R6381
R6377
C6344
TL4825
R5919
C6359C6365
C5886C5803
C5888
R6380 R5924 R5928 FB6211
R5920
R4830
C5884
C5881
C5801
R5849
R5895
R5896
R5897
C5885 C5827
C5883 C5820
C5882 FB5813
C5880
C5879
C5877
C6361C6363 C5870
C6368
R5853
FB6345
R5933R5929 C5864
FB4801 R6366 FB6215
C5802
C5869 C5851 C5852 C5858
C5839 C5878
R5848
C6257
C6255
FB6216
R6365 C5846 C5847 C5860
C5825
C5836
C5811 C5867
C6351 C6349
C5849
C5859
R5852
R5911
X5802 C5810 C5848 C6259 C6253
C5838
C6373 C6369 C5815 C6260 C6258 C6256 C6254
R5847
C6352 C6350 C6356
X5801
FB5814
R5882
R6335
R6333
R6334
R6325
TL6026
C5855
R5912
C6355 TL6025
R5851
C5866
C5868
C6372 C5824
R6376
R6375
C6367 C5841 C5850

TL6294 C6354
C5865
R5846
R5836 C5819 C5843 C5853
R6336
R6322
R6323
R6324
TL6293 C6366
C6298 C5861
R5850
FB6346
TL6292 C5814 C5845

C5863 C5862
C6251 C6249 C6247 C6271 C6245

C6297
C6252 C6250 C6248 C6272 C6246

TL6291
C5813
C5818
C5807
R5845
FB6284
C6285
TL6290 FB6342
C5808
C5816
D C5809
C5840
C5842
R5837
TL6289 C6017
C6152
C5857
C6153
TL6288 C6296 C5823
R5844
C6008 C5821 C5844 C5854
TL6287
FB5809
R5835
TL6286 FB6002 C5812 C5856
R6082
R6316
R6081 R6128
TL6285 C6010 IC6212

FB6285
R5843
C6286
R6312 R6313 R6314

R6096
R6013
C5835
C5837
C5834
TL6284 C6007 C5832
TL5831
R5834
R6017
C5822
R6127
TL6283 R6015
C5817
C5826
C5830
C5828
C5805
TL5834 C5833
R5838
C6154 C6024 C6043
R5918
C5804
C5806
C5875
TL6295
C6108
C6109 C6041 C6042 C6031 C6032 C6101
R5827
R5840
R6019
C5831
C5876
C5874
FB6287
C6102
C6157
C6151
C6150 C6039
C6155
R5801
C5872
R5804
C5871
C5873
C6107
R5833
C6156
R5824
C6103 C5829
C6294
C6293
C6295
C6025
C6291 R6083 R6094
R5832
R5825
C6110 FB5815
R6021
R5805
C6040
C6292
R6012
R5829
C6106 C6026C6111
R6023
TL6282 C6038
R6319 R6320
FB6281
C6281
R5830
R6282
C6105 C6037 C6027 C6160

C
R5806
C6044
R6011
R6318 R6330
C6028
C6104 TL5826
R6025
R5828
C6036 C6045 C6161
R5884 R5822 R5839
R5857
R6317 R6329
C6030 C6023 C6144
R5886
R5885
C6242 C6243
C6029C6112
R5889
R5831
R6281
C6034 C6033 R5808
R5807
C6158
R6010
R6232
R6233
R6234
C6241
C6244
TL6224 TL6219
C6290
R5814
TL6281 R6328 R6327 R6093
C6035 C6148
C6022C6113 R6090 R5821 R6238 R6239

C6159 R5812
FB6282
C6149
C6282
C6145
C6142 R5810 R5818 R5816 R6237 R6241 TL6222 TL6221

R6002
TL5825
C6100
R6080 R5813 R6252

R5809
C6146
C6283 R6091 C6143 R6236 R6242

C6288 R5815 R6250 TL6223 TL6220
C6147 R5817
FB6283
FB6286
R6235 R6244
C6284
R6009 R6006 R6004

R6097
R6008
C6287 C6289 R6249

TL5832
R6246
R6247
R6248
C6374
R5894
R5893
R5892
R5891
TL5833
IC6342
2
B TL6350 TL6342 TL6344 TL6346
FB5806
FB5805
FB5807
FB5808
C5893
TL6341 TL6345 TL6348 TL6349
TL6343 TL6347
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
7 18
[9] POWER UNIT PRINTED WIRING BOARD
POWER Unit (Component Side)
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
7 19
POWER Unit (Chip Parts Side)
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
7 20
CHAPTER 8. SCHEMATIC DIAGRAM
LC46XL1E
Service Manual
[1] DESCRIPTION OF SCHEMATIC DIAGRAM

VOLTAGE MEASUREMENT CONDITION:
1. The voltages at test points are measured on exclusive AC adaptor and the stable supply voltage of AC 230V.
Signals are fed by a colour bar signal generator for servicing purpose and the above voltages are measured with a 20k ohm/V tester.
INDICATION OF RESISTOR & CAPACITOR:

RESISTOR
1. The unit of resistance is omitted.
(K=k=1000 , M=M).
2. All resistors are 5%, unless otherwise noted.
(K= 10%, F= 1%, D= 0.5%)
3. All resistors are 1/16W, unless otherwise noted.
CAPACITOR
1. All capacitors are F, unless otherwise noted.
(P=pF=F).
2. All capacitors are 50V, unless otherwise noted.
CAUTION:
This circuit diagram is original one, therefore there may be a
slight difference from yours.
SAFETY NOTES:
1. DISCONNECT THE AC PLUG FROM THE AC
OUTLET BEFORE REPLACING PARTS.
2. SEMICONDUCTOR HEAT SINKS SHOULD BE
REGARDED AS POTENTIAL SHOCK HAZARDS
WHEN THE CHASSIS IS OPERATING.
IMPORTANT SAFETY NOTICE:

PARTS MARKED WITH ( ) ARE
IMPORTANT FOR MAINTAINING THE SAFETY OF THE
SET. BE SURE TO REPLACE THESE PARTS WITH
SPECIFIED ONES FOR MAINTAINING THE SAFETY AND
PERFORMANCE OF THE SET.
81
[2] SCHEMATIC DIAGRAM
MAIN Unit-1
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
82
MAIN Unit-2
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
83
MAIN Unit-3
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
84
MAIN Unit-4
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
85
MAIN Unit-5
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
86
MAIN Unit-6
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
87
MAIN Unit-7
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
88
MAIN Unit-8
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
89
AV Unit
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
8 10
DIGITAL Unit-1
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
8 11
DIGITAL Unit-2
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
8 12
DIGITAL Unit-3
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
8 13
DIGITAL Unit-4
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
8 14
D-TUNER Unit
J AND SHADED COMPONENTS=SAFETY RELATED PARTS
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
8 15
KEY Unit R/C, LED Unit
J J
I I
H H
G G
F F
E E
D D
C C
B B
A A
1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 10
8 16
ILLUMINATION Unit
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
8 17
FRC Unit-1
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
8 18
FRC Unit-2
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
8 19
FRC Unit-3
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
8 20
FRC Unit-4
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
8 21
FRC Unit-5
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
8 22
FRC Unit-6
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
8 23
POWER Unit
AND SHADED COMPONENTS=SAFETY RELATED PARTS
J
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
8 24
PartsGuide
PARTS GUIDE
LCD COLOUR TELEVISION
LC-46XL1E/RU
MODELS LC-52XL1E/RU
CONTENTS
[1] PRINTED WIRING BOARD [8] DUNTKD909FM01 (R/C, LED Unit)

ASSEMBLIES
[9] DUNTKD888FM02
[2] LCD PANEL AND TUNER (NOTE: (ILLUMINATION Unit)
THE PARTS HERE SHOWN ARE
SUPPLIED AS AN ASSEMBLY BUT [10] DUNTKE046FE02 (FRC Unit)
NOT INDEPENDENTLY.)
[11] RDENCA229WJQZ (POWER Unit)
[3] DUNTKE191FM01 (MAIN Unit)
[12] CABINET PARTS
[4] DUNTKD604FM11 (AV Unit)
[13] SUPPLIED ACCESSORIES
[5] DUNTKD628FM20 (DIGITAL Unit)
[14] PACKING PARTS
[6] DUNTKD984FM03 (D-TUNER Unit) (NOT REPLACEMENT ITEM)
[7] DUNTKD910FM01 (KEY Unit) [15] SERVICE JIGS

(USE FOR SERVICING)
Parts marked with " " are important for maintaining the safety of the set. Be sure to replace these
parts with specified ones for maintaining the safety and performance of the set.
This document has been published to be used

for after sales service only.
The contents are subject to change without notice.
NO. PARTS CODE PRICE NEW PART DESCRIPTION
RANK MARK DELIVERY
[1] PRINTED WIRING BOARD ASSEMBLIES

N DUNTKE191FM01 CB N R MAIN Unit
N DUNTKD604FM11 BL N R AV Unit
N DUNTKD628FM20 BV N R DIGITAL Unit
N DUNTKD984FM03 - N S D-TUNER Unit (NOT REPLACEMENT ITEM)
N DUNTKD910FM01 AH N R KEY Unit
N DUNTKD909FM01 AU N R R/C, LED Unit
N DUNTKD888FM02 AG N R ILLUMINATION Unit
N DUNTKE046FE02 CC N J FRC Unit
N RDENCA229WJQZ CC N R POWER Unit
[2] LCD PANEL AND TUNER (NOTE: THE PARTS HERE SHOWN ARE SUPPLIED AS AN ASSEMBLY BUT
NOT INDEPENDENTLY.)
N R1LK460D3LZ2CY N J 46" LCD Panel Module
N R1LK520D3LZ2CY N J 52" LCD Panel Module
! TU201 RTUNQA035WJZZ AX S Hybrid Tuner
C1701 VCKYCY1EF104ZY AA J Capacitor 0.1 25V Ceramic
C1702 VCKYCY1HB103KY AA J Capacitor 0.01 50V Ceramic
C1704 VCAAPD1AJ686MY AE J Capacitor 68 10V Electrolytic
C1706 RC-KZA070WJZZY AD J Capacitor 22 6.3V Ceramic
C1708 VCKYTV1CB105KY AC J Capacitor 1 16V Ceramic
C1711 RC-KZA073WJZZY AD J Capacitor 10 16V Ceramic
C1715 VCEASX1VN226MY AC J Capacitor 22 35V Electrolytic
C1716 VCEASX1CN226MY AC J Capacitor 22 16V Electrolytic
C1717 VCKYCY1HB682KY AA J Capacitor 6800p 50V Ceramic
C1743 VCCCCY1HH220JY AA J Capacitor 22p 50V Ceramic
C1745 VCCCCY1HH560JY AB J Capacitor 56p 50V Ceramic
C1746 VCEASX0JN476MY AC J Capacitor 47 6.3V Electrolytic
2
RANK MARK DELIVERY

C2318 VCCCCY1HH100DY AA J Capacitor 10p 50V Ceramic
C2329 RC-KZA510WJPZY AB J Capacitor 10 16V Ceramic
C2706 VCEASX1HN105MY AB J Capacitor 1 50V Electrolytic
C2718 VCKYCY1CF105ZY AA J Capacitor 1 16V Ceramic
3
RANK MARK DELIVERY

C2719 VCKYCY1CF105ZY AA J Capacitor 1 16V Ceramic
C2726 VCKYTV1EB104KY AB J Capacitor 0.1 25V Ceramic
C2740 VCKYTV1HB103KY AA J Capacitor 0.01 50V Ceramic
4
RANK MARK DELIVERY

C3335 VCEASY1CN476MY AC J Capacitor 47 16V Electrolytic
C3501 VCKYCZ1CF104ZY AA J Capacitor 0.1 16V Ceramic
C3529 RC-KZ0124TAZZY AC J Capacitor 10 6.3V Ceramic
C3537 VCCCCZ1HH101JY AB J Capacitor 100p 50V Ceramic
C3560 RC-KZA067WJZZY AB J Capacitor 4.7 10V Ceramic
C3564 VCKYCZ1HB102KY AB J Capacitor 1000p 50V Ceramic
5
RANK MARK DELIVERY

C3708 VCEASX1HN335MY AB J Capacitor 3.3 50V Electrolytic
C3717 VCCCCY1HH5R0CY AA J Capacitor 5p 50V Ceramic
C3718 VCCCCY1HH6R0DY AA J Capacitor 6p 50V Ceramic
C3740 VCKYCY1HF224ZY AA J Capacitor 0.22 50V Ceramic
D1702 RH-EX0487CEZZY AC J Zener Diode, HZM2.0NBTL-E
D1703 VHD1SS352//-1Y AB J 1SS352(TPH3,F)
D1704 VHDTCCMS01+-1Y AE J CMSO1(TE12L,Q)
D1707 RH-EX0487CEZZY AC J Zener Diode, HZM2.0NBTL-E
D1901 VHDDAN202K/-1Y AB J DAN202KT146
D1913 VHDRB520S30-1Y AC J Diode RB520S-30TE61
D2301 RH-EX1271CEZZY AB J Zener Diode HZU12B2TRF
D2305 RH-EX1247CEZZY AB J Zener Diode HZU5.6B2TRF
D2310 VHD1SS226//-1Y AC J Diode 1SS226(T5L,F,T)
D2707 VHD1SS390++-1Y AB J Diode 1SS390TE61
FB1701 RBLN-0250TAZZY AC J Balun
FB1703 RBLN-0061TAZZY AD J Balun
FB1901 RBLN-0060TAZZY AB J Balun
6
RANK MARK DELIVERY

FB2701 RBLN-0254TAZZY AA J Balun
FL2301 RFiLN0003TAZZY AD J Filter
FL2304 RCiLFA071WJZZY AD J Coil
IC1701 VHiBU4239G+-1Y AE J IC BU4239G-TR
IC1702 VHiPQ20WZ11-1Y AF J IC PQ20WZ1UJ00H
IC1705 VHiPQ1R50//-1Y AF J IC PQ1R50J0000H
IC1706 VHiMP1583++-1Y AH J IC MP1583DN-LF-Z
IC1708 VHiMP1410ES-1Y AP J IC MP1410ES-LF-Z
IC1709 VSSSM6J51TU-1Y AF J IC SSM6J51TU(TE85L,F)
IC1710 RH-iXB946WJZZQ AU N J IC EPM240T100C5N
IC1712 VHiMP1410ES-1Y AP J IC MP1410ES-LF-Z
IC1901 RH-iXB936WJZZS J IC EDID HDMI(EXT 5)
IC1902 RH-iXB937WJZZS J IC EDID HDMI(EXT 6)
IC1905 VHiSii9025+-1Q AX N J IC SII9025CTU
IC2301 VHiiCL3225E-1Y AN J IC ICL3225ECAZ-T
IC2303 RH-iXB938WJZZS J IC EDID (PC)
IC2304 VHiTL712CPW-1Y AK J IC TL712CPWR
IC2305 VHiTL712CPW-1Y AK J IC TL712CPWR
IC2306 VHiTC7W53U/-1Y AF J IC TC7W53FU(TE12L,F)
7
RANK MARK DELIVERY

IC2307 VHiTC7W00U/-1Y AE J IC TC7W00FU(TE12L,F)
IC2701 VHiLCX125FT-1Y AD J IC TC74LCX125FT(EL,K)
IC2704 VHiTC4052BT-1Y AF J IC TC4052BFT(EL,N,M)
IC3001 RH-iXA992WJZZY AM J IC M24256-BWMN6TP
IC3002 RH-iXB755WJZZQ BZ J IC VGC5969B-AD-A3
IC3003 VHiT7WB125A-1Y AE J IC TC7WBD125AFK(T5L,F)
IC3004 VHiBU4228G+-1Y AD J IC BU4228G-TR
IC3005 VHiBU4214G+-1Y AE J IC BU4214G-TR
IC3301 RH-iXB064WJN1Q BR J IC FRC9429A-XX-B2
IC3501 RH-iXB765WJQZQ AW J IC K4H561638H-UCB3
IC3502 RH-iXB765WJQZQ AW J IC K4H561638H-UCB3
IC3503 RH-iXB754WJZZQ BF J IC M29DW128F70NF6E
IC3504 RH-iXB753WJZZY AN J IC SN74LVCH16373ADGGR
IC3506 VHiBD3533F+-1Y AG J IC BH25FBIWG-TR
IC3701 RH-iXB752WJZZQ BH J IC MSP4410K-QA-D6
IC3702 VHiAK4363VF-1Y AQ J IC AK4363VF
J2701 QJAKEA073WJZZ AD J Jack HDMI INPUT
J2702 QJAKEA073WJZZ AD J Jack RGB INPUT
L1701 RCiLPA212WJZZY AF J Coil
L1702 RCiLPA213WJZZY AG J Coil
L1901 RCiLFA134WJZZY AF J Coil
L2703 VPCUN1R5MR12NY AC J Peaking 1.5H
LUG1701 QLUGHA006WJZZY AC J Lug
LUG1705 QLUGZA002WJZZY AC J Lug
P1701 QPLGNA343WJZZY AD J Plug 9pin (LB)
P1702 QPLGN1075TAZZY AD J Plug 10pin
P2302 QPLGNA338WJZZY AD J Plug 4pin (KM)
P2303 QPLGNA347WJZZY AD J Plug 13pin(RA)
P2304 QSOCNA472WJZZY AD J Socket 20pin
P2702 QCNCMA202WJZZY AK J Connector 60pin
P3001 QPLGNA339WJZZY AD J Plug 5pin (D)
Q1701 VS2SC3928AR-1Y AA J Transistor 2SC3928A-T112-1R
Q1702 VS2SA1530AR-1Y AB J Transistor 2SA1530A-T112-1R
Q1706 VSCPH6318++-1Y AE J Transistor CPH6318-TL-E
Q1901 VS2SK536///-1Y AE J Transistor 2SK536-TB-E
Q1905 VSDTC144EE/-1Y AA J Transistor DTC144EETL
Q2302 VSDTC114EE/-1Y AB J Transistor DTC114EETL
Q2303 VSDTC114EE/-1Y AB J Transistor DTC114EETL
Q2709 VSSSM3K15FS-1Y AC J Transistor SSM3K15FS(TE85L,F)
8
RANK MARK DELIVERY

R1700 VRS-CY1JF101JY AA J Resistor 100 1/16W Metal Oxide
R1701 VRS-CY1JF562JY AA J Resistor 5.6k 1/16W Metal Oxide
R1702 VRS-CY1JF103JY AA J Resistor 10k 1/16W Metal Oxide
R1703 VRS-TW2ED000JY AB J Resistor 0 1/4W Metal Oxide
R1706 VRS-CZ1JF333JY AA J Resistor 33k 1/16W Metal Oxide
R1719 VRS-CY1JF622FY AA J Resistor 6.2k 1/16W Metal Oxide
R1721 VRS-CY1JF203FY AA J Resistor 20k 1/16W Metal Oxide
R1726 VRS-CY1JF511FY AA J Resistor 510 1/16W Metal Oxide
R1739 VRS-TW2HF1R0JY AA J Resistor 1 1/2W Metal Oxide
R1762 VRS-CZ1JF220JY AA J Resistor 22 1/16W Metal Oxide
9
RANK MARK DELIVERY

R1911 VRS-CJ1JF474JY AA J Resistor 470k 1/16W Metal Oxide
R1914 VRS-CJ1JF100JY AA J Resistor 10 1/16W Metal Oxide
R1920 VRS-CH1JF100JY AA J Resistor 10 1/16W Metal Oxide
R1932 VRS-CY1JF105JY AA J Resistor 1.0M 1/16W Metal Oxide
R2305 VRS-CH1JF103JY AA J Resistor 10k 1/16W Metal Oxide
10
RANK MARK DELIVERY

R2322 VRS-TW2ED750JY AA J Resistor 75 1/4W Metal Oxide
R2712 VRS-CJ1JF472JY AA J Resistor 4.7k 1/16W Metal Oxide
11
RANK MARK DELIVERY

R2776 VRS-CY1JF4R7JY AA J Resistor 4.7 1/16W Metal Oxide
R3045 VRS-CZ1JF680JY AB J Resistor 68 1/16W Metal Oxide
R3501 VRK-CD1JJ680JY AC J Resistor 68 1/16W Metal Composition
R3507 VRS-CZ1JF102JY AA J Resistor 1.0k 1/16W Metal Oxide
12
RANK MARK DELIVERY

R3708 VRS-CY1JF105JY AA J Resistor 1.0M 1/16W Metal Oxide
13
RANK MARK DELIVERY

S3001 QSW-K0095CEZZ AB J Switch
S3501 QSW-SA020WJZZY AE J Boot Switch
SC1701 QCNCWA251WJZZY AH J Connector 23pin (PA)
SC1702 QCNCWA248WJZZY AD J Connector 9pin (PB)
SC1901 QSOCZA072WJZZQ AH J Socket 23pin (HDMI)
SC1902 QSOCZA072WJZZQ AH J Socket 23pin (HDMI)
SC2301 QSOCDA036WJZZ AF J Socket RS-232C
SC2302 QCNCWA507WJQZY AM J Connector 41pin (LV)
SC2303 QSOCNA229WJZZ AH J Socket D-SUB
SC2702 QCNCWA251WJZZY AH J Connector 23pin
SC2705 QCNCWA010WJZZY AE J Connector 15pin
TH3003 VHHM1103J03-1Y AC J Thermistor
X1901 RCRSCA108WJZZY AF J Crystal
X3001 RCRSC0012CEZZY AH J Crystal 20.25MHz
X3301 RCRSC0012CEZZY AH J Crystal 20.25MHz
X3701 RCRSB0250GEZZ+ AG J Crystal 18.432MHz

C324 VCEASX1HN106MY AC J Capacitor 10 50V Electrolytic
C330 VCESYA1VM477M+ AF J Capacitor 470 35V Electrolytic
C331 VCESYA1VM477M+ AF J Capacitor 470 35V Electrolytic
C338 RC-EZA513WJZZ AH J Capacitor 470 50V Electrolytic
C339 RC-EZA513WJZZ AH J Capacitor 470 50V Electrolytic
C340 VCKYTV1EB224KY AA J Capacitor 0.22 25V Ceramic
C342 VCFYFA1HA684J+ AC J Capacitor 0.68 50V
C343 VCFYFA1HA684J+ AC J Capacitor 1 10V Ceramic
14
RANK MARK DELIVERY

C356 VCEASY1HN476MY AD J Capacitor 47 50V Electrolytic
C357 VCEASY1HN476MY AD J Capacitor 47 50V Electrolytic
C361 RC-KZA237WJZZY AB J Capacitor 10 16V Ceramic
C364 VCEASY1CN477MY AD J Capacitor 470 16V Electrolytic
C1129 VCCCTV1HH101JY AA J Capacitor 100p 50V Ceramic
15
RANK MARK DELIVERY

D311 RH-EXA103WJZZY AB J Zener Diode UDZSTE-1736B
D312 RH-EXA103WJZZY AB J Zener Diode UDZSTE-1736B
D313 RH-EX1026CEZZY AB J Zener Diode, MAZ80390HL
D314 RH-EX1295CEZZY AB J Zener Diode HZU30BTRF-E
D1101 RH-EX1068CEZZY AB J Zener Diode MAZ81500ML
D1201 RH-EX1239CEZZY AB J Zener Diode 4.3V
FL1101 RFiLN0017TAZZY AC J Filter
IC301 VHiTDA8931T-1Y AS J IC TDA8931T/N1,118
IC302 VHiTDA8931T-1Y AS J IC TDA8931T/N1,118
IC303 VHiNJM4558M-1Y AD J IC NJM4558M-TE1
IC1101 VHiMM1506XN-1Y AD J IC MM1506XNRE
J1101 QSOCZA116WJZZ AK J Socket INPUT1/2
J1201 QJAKZA033WJZZ AK J Jack INPUT3
J1301 QJAKJA007WJZZ AD J Jack Headphone OUT
L301 RCiLPA697WJZZ AE J Coil
L302 RCiLPA697WJZZ AE J Coil
P301 QPLGNA173WJZZY AD J Plug 4pin (SP)
P1101 QCNCMA250WJZZ AE J Connector 23pin
16
RANK MARK DELIVERY

Q303 VSDTC314TK/-1Y AC J Transistor DTC314TKT146
R318 VRS-TW2HF820JY AB J Resistor 82 1/2W Metal Oxide
R355 VRS-TW2ED2R7JY AB J Resistor 2.7 1/4W Metal Oxide
R1107 VRS-TV1JD221JY AA J Resistor 220 1/16W Metal Oxide
17
RANK MARK DELIVERY

SC301 QSOCZ0738CEZZ AE J Socket 7pin

18
RANK MARK DELIVERY

19
RANK MARK DELIVERY

C4716 VCKYCY1AB105KY AB J Capacitor 0.33 10V Ceramic
C4717 VCEASX0JN226MY AB J Capacitor 22 6.3V Electrolytic
D4701 RH-EX1234CEZZY AE J Zener Diode HZU3.6B2TRF, 3.6V
D4702 VHDSFPA73//2EY AD J Diode SFPA-73VL
FB4001 RBLN-A215WJZZY AB J Balun
IC4001 RH-iXB680WJZZQ BH J IC STI5516AUCL
IC4002 VHiTC7SH08U-1Y AF J IC TC7SH08FU(TE85L,JF)
IC4003 VHiBU4228G+-1Y AD J IC BU4228G-TR
IC4005 VHiTC7SHU04-1Y AD J IC TC7SHU04FU(T5L,JF)
IC4201 RH-iXB742WJZZQ AX J IC K4S641632K-UC75
IC4202 RH-iXB742WJZZQ AX J IC K4S641632K-UC75
IC4203 RH-iXC100WJZZQ AV N J IC M29W160ET70N6E
IC4204 VHiBR24L64F-1Y AK J IC BR24L64F-WE2
IC4401 VHiLCX245FT-1Y AD N J IC TC74LCX245FT(EKJ)
IC4402 VHiLCX573FT-1Y AF J IC TC74LCX573FT(EKJ)
IC4403 VHiTC7SH08U-1Y AF J IC TC7SH08FU(TE85L,JF)
IC4404 VHiLCX244FT-1Y AE J IC TC74LCX244FT(EL,K)
IC4405 VHiLCX573FT-1Y AF J IC TC74LCX573FT(EKJ)
IC4406 VHiTC7SH32U1EY AC J IC TC7SH32FU(TE85L,JF)
IC4407 VHiTC7SH32U1EY AC J IC TC7SH32FU(TE85L,JF)
IC4408 VHiTC7SH02U1EY AD J IC TC7SH02FU(T5L,JF,T)
IC4604 VHiTSH73CPT-1Y AL J IC TSH73CPT
IC4701 VHiMP1583++-1Y AH J IC MP1583DN-LF-Z
IC4704 VHiPQ018ENA-1Y AF J IC PQ018ENA1ZPH
L4601 VPD9M100J1R7NY AC J Peaking 10H
L4603 VPD9M5R6J1R6NY AB J Peaking 5.6H
P4001 QPLGN0463TAZZY AC J Plug 4pin (RS)
P4003 QPLGN0463TAZZY AC J Plug 4pin (RS1)
Q4401 RH-TXA026WJZZY AD J Transistor PBLS2001D,115
Q4704 VSCPH6318++-1Y AE J Transistor CPH6318-TL-E
20
RANK MARK DELIVERY

21
RANK MARK DELIVERY

22
RANK MARK DELIVERY

R4709 VRS-TX2HF000JY AB J Resistor 0 1/2W Metal Oxide
R4713 VRS-TX2HF1R0JY AB J Resistor 1 1/2W Metal Oxide
SC4601 QCNCWA202WJZZY AK J Connector 60pin
SC4602 QSOCNA003WJZZY AM J Socket 100pin
X4001 RCRSC0032TAZZY AG J Crystal 32.768kHz
X4002 RCRUAA075WJZZY AQ J Crystal
N PMLT-A314WJZZ AE J Absorber
N PSLDMA838WJZZ AD J Shield
N PSLDMA943WJFW AK J Main Shield
N PSLDMB056WJFW AK N J Shield
N XJPS730P08WS0 AA J Screw x 4
N QCNCMA225WJSA AY N J Connector
N XBPSN20P14JS0 AB J Screw
[6] DUNTKD984FM03 (D-TUNER Unit)

C204 VCEASX1CN477MY AE J Capacitor 470 16V Electrolytic
C207 VCEASX0JN226MY AB J Capacitor 22 6.3V Electrolytic
C221 VCERML1CN107MY AC J Capacitor 100 16V Electrolytic
C224 VCKYTV1CB224KY AB J Capacitor 0.22 16V Ceramic
C226 VCEASX1AN227MY AD J Capacitor 220 10V Electrolytic
C228 VCKYTV1CB474KY AC J Capacitor 0.47 16V Ceramic
C241 VCEASX1AN336MY AC J Capacitor 33 10V Electrolytic
23
RANK MARK DELIVERY

FL201 RFiLC0278BMZZ AM J Filter
FL202 RFiLC0294BMZZ AA J Filter
IC201 VHiTDA9886+-1Y AQ J IC TDA9886TS/V4
IC202 RH-iXB964WJZZQ J IC STV0362
IC203 VHiTC7W53U/-1Y AF J IC TC7W53FU(TE12L,F)
IC204 VHiLV4053FT-1Y AE J IC TC74LVX4053FT(EL)
IC205 VHiMM3271AN-1Y J IC MM3271ANRE
IC206 VHiPQ1M335M-1Y AD J IC PQ1M335M2SPQ
IC207 VSSSM6J51TU-1Y AF J IC SSM6J51TU(TE85L,F)
IC208 VHiBH25FB1G-1Y AD J IC BH25FBIWG-TR
IC209 VHiMCP30215-1Y N J IC MCP30215A5T-E/OT
L201 VPCNN2R2JR77NY AB J Coil Peaking 2.2H
L203 VPCNN100J1R6NY AB J Coil Peaking 10H
L204 VPCNN120J1R9NY AB J Coil Peaking 12H
L205 VPCNN330J4R2NY AC J Coil Peaking 33H
P201 QCNCMA012WJZZ AD J Plug 15pin
Q205 VSRN4904///-1Y AB J Transistor RN4904(TE85L,F)
24
RANK MARK DELIVERY

R231 VRS-TQ2BD330JY AA J Resistor 33 1/8W Metal Oxide
SLD201 PSLDMA898WJFW AD J Digital Shield
X201 RCRSAA029WJZZ AF J Crystal
X202 RCRSCA039WJZZY AG J Crystal
[7] DUNTKD910FM01 (KEY Unit)

D151 RH-EX0646GEZZY AA J Zener Diode MTZJT-7215B
P151 QPLGNA058WJZZ AC J Plug 4pin (KM)
R151 VRD-RA2BE822JY AA J Resistor 8.2k 1/8W Carbon
R152 VRD-RA2BE123JY AA J Resistor 12k 1/8W Carbon
R153 VRD-RA2BE822JY AA J Resistor 8.2k 1/8W Carbon
S151 QSW-K0003AJZZ+ AA J Switch CH-UP
S152 QSW-K0003AJZZ+ AA J Switch CH-DOWN
S153 QSW-K0003AJZZ+ AA J Switch MENU
S154 QSW-K0003AJZZ+ AA J Switch VOL-UP
S155 QSW-K0003AJZZ+ AA J Switch VOL-DOWN
S157 QSW-K0003AJZZ+ AA J Switch
[8] DUNTKD909FM01 (R/C, LED Unit)
C102 VCKYTV1CF225ZY AB J Capacitor 2.2 16V Ceramic
D101 RH-EXA092WJZZY AB J Diode UDZSNPTE-1712B
D103 RH-PX0421CEZZY AD J Diode CL-165HR/YG-D-T
IC101 VHITPS850++-1Y AG J IC TPS850
P101 QPLGNA333WJZZY AD J Plug 13pin (RA)
RMC101 RRMCUA053WJZZ AE J Remote Receiver
SLD101 PSLDM4646CEFW AD J Shield
25
RANK MARK DELIVERY
[9] DUNTKD888FM02 (ILLUMINATION Unit)

D901 RH-PXA137WJQZY AF J LED Blue, TV POW
P901 QPLGNA324WJZZY AC J Plug 4pin
[10] DUNTKE046FE02 (FRC Unit)
C4801 RC-KZA521WJQZY AA J Capacitor
C4803 VCKYCZ1EB822KY AA J Capacitor 8200p 25V Ceramic
C4804 VCAAPE1CJ686MY AE J Capacitor 68 16V Electrolytic
C4809 VCKYCY1CB104KY AB J Capacitor 0.1 16V Ceramic
C4810 VCKYCZ1AB105KY AA J Capacitor 1 10V Ceramic
C4812 VCKYCZ1EB822KY AA J Capacitor 8200p 25V Ceramic
C4813 RC-KZA114WJZZY AB J Capacitor
C4814 RC-KZA521WJQZY AA J Capacitor
C4823 VCKYCZ1HB221KY AA J Capacitor 220p 50V Ceramic
C4824 VCKYCY1CB104KY AB J Capacitor 0.10 16V Ceramic
C4825 VCKYCY1AB334KY AB J Capacitor 0.33 10V Ceramic
C5801 VCKYCZ1AB104KY AB J Capacitor 0.1 10V Ceramic
26
RANK MARK DELIVERY

C6006 VCCCCZ1HH102JY AA J Capacitor 1000p 50V Ceramic
C6007 RC-KZA041WJZZY AC J Capacitor 10 10V Ceramic
27
RANK MARK DELIVERY

28
RANK MARK DELIVERY

29
RANK MARK DELIVERY

30
RANK MARK DELIVERY

D4801 RH-EX1400CEZZY AB J Zener Diode UDZSTE-1710B, 10V
D4802 VHDD1FH3+++-1Y AD J Diode D1FH3
D4803 VHDD1FH3+++-1Y AD J Diode D1FH3
D4804 RH-EX1400CEZZY AB J Zener Diode UDZSTE-1710B, 10V
IC4801 VHiTPS40055-1Y AN J IC TPS40055PWPR
IC4802 RH-iXA552WJZZY AH J IC PQ1CY1032ZPH
IC4803 RH-iXA552WJZZY AH J IC PQ1CY1032ZPH
IC4804 VHiPST3629N-1Y AD J IC PST3629NR
IC4805 VHiPST3629N-1Y AD J IC PST3629NR
IC5801 RH-iXB857WJZZQ BP N J IC iXB857WJZ
IC6001 RH-iXB822WJQZQ AY J IC EM6A9320BI-5MG
IC6004 RH-iXA361WJZZY AM J IC LP2995MX/NOPB
IC6211 VHiTLVD1023-1Q AS J IC TLVD1023
IC6212 VHiTLVD1023-1Q AS J IC TLVD1023
IC6281 VHiTLVD104S-1Q AN N J IC TLVD104S
IC6282 VHiTLVD104S-1Q AN N J IC TLVD104S
IC6341 RH-iXC029WJQZQ BA J IC iXC029WJ
31
RANK MARK DELIVERY

IC6342 RH-iXC030WJN2Y AQ N J IC IXC030WJ
L4801 RCiLCA029WJZZY AD J Coil
L4802 RCiLP0295TAZZY AD J Coil
L4803 RCiLP0297TAZZY AD J Coil
L6211 RCiLFA071WJZZY AD J Coil
L6341 VPCEM220M1R7NY AC J Coil Peaking 22H
P4801 QPLGNA412WJZZY AG J Plug 20pin
P4802 QPLGNA345WJZZY AD J Plug 11pin
P5801 QPLGNA324WJZZY AC J Plug 4pin
P5802 QPLGN0057CEZZY AD J Plug 7pin
P6341 QPLGN0060CEZZY AE J Plug 10pin
Q4801 VSRT1N144U/-1Y AB J Transistor RT1N144U-T111-1
Q4803 VSSP8K4++++-1Y AF J Transistor SP8K4TB
Q6341 VSRT1N144U/-1Y AB J Transistor RT1N144U-T111-1
R4801 VRS-CZ1JF473FY AA J Resistor 47k 1/16W Metal Oxide
R4803 VRS-CZ1JF103FY AB J Resistor 10k 1/16W Metal Oxide
R4819 VRS-CZ1JF682FY AA J Resistor 6.8k 1/16W Metal Oxide
R4826 VRS-CZ1JF3R3JY AA J Resistor 3.3 1/16W Metal Oxide
R5804 VRK-SB1FF330JY AA J Resistor 33 1/32W Metal Composition
32
RANK MARK DELIVERY

33
RANK MARK DELIVERY

R5911 VRS-CY1JF105FY AA J Resistor 1M 1/16W Metal Oxide
R5913 RBLN-0083GEZZY AB J Balun
R5914 RBLN-0083GEZZY AB J Balun
34
RANK MARK DELIVERY

35
RANK MARK DELIVERY

R6287 VRS-CZ1JF101FY AA J Resistor 100 1/16W Metal Oxide
36
RANK MARK DELIVERY

SC6211 QCNCWA671WJQZY AH J Connector 41pin
X5801 RCRSCA086WJZZY AG J Crystal
X6341 RCRUAA056WJQZY AK J Crystal 33.000MHz

C6 9JG0034007969 AD J Capacitor 0.47 16V Ceramic
C10 9JG0034006911 AA J Capacitor 1000p 50V Ceramic
C11 9JG0034017174 AB J Capacitor 0.1 50V Ceramic
C12 9JG0034002177 AB J Capacitor 47000p 50V Ceramic
C13 9JG0034038538 AC J Capacitor 1 16V Ceramic
! C701 9JG0034012369 AG J Capacitor 0.47 AC275V Film
! C702 9JG0034029997 AE J Capacitor 0.33 AC275V Film
! C703 9JG0034018278 AE J Capacitor 0.1 AC275V Film
! C704 9JG0034011540 AD J Capacitor 2200p AC250V Ceramic
! C708 9JG0034006113 J Capacitor 220p AC250V Ceramic
! C709 9JG0034006113 J Capacitor 220p AC250V Ceramic
C710 9JG0034160996 AL J Capacitor 1 450V Film
C712 9JG0034006601 AG J Capacitor 0.47 50V Film
C715 9JG0034017123 AC J Capacitor 470p 50V Ceramic
C721 9JG0034122164 AD J Capacitor 10 6.3V Ceramic
C722 9JG0034116962 AD J Capacitor 0.001 630V Film
C724 9JG0034019037 AG J Capacitor 2200p 2kV Ceramic
C725 9JG0034018405 J Capacitor 1000p 2kV Ceramic
C726 9JG0034094233 AV J Capacitor 150 450V Electrolytic
C728 9JG0034094233 AV J Capacitor 150 450V Electrolytic
C729 9JG0034006601 AG J Capacitor 0.47 50V Film
C731 9JG0034058199 AC J Capacitor 2.2 50V Electrolytic
C732 9JG0034033099 AD J Capacitor 100p 1kV Ceramic
37
RANK MARK DELIVERY

C734 9JG0034087121 AE J Capacitor 0.056 630V Film
C739 9JG0034020310 AC J Capacitor 2.2 10V Ceramic
C741 9JG0034000204 AB J Capacitor 0.1 50V Film
C748 9JG0034021171 AC J Capacitor 22 50V Electrolytic
C751 9JG0034001960 AC J Capacitor 220p 2kV Ceramic
C757 9JG0034122008 AC J Capacitor 470p 50V Ceramic
C762 9JG0034087032 AE J Capacitor 0.01 630V Film
C771 9JG0034164231 AK J Capacitor 470 100V Electrolytic
C772 9JG0034164231 AK J Capacitor 470 100V Electrolytic
C785 9JG0034021201 AF J Capacitor 2200 10V Electrolytic
C800 9JG0034031819 AD J Capacitor 1000 10V Electrolytic
C801 9JG0034017174 AB J Ceramic 0.1 50V Capacitor
C813 9JG0034021155 AD J Capacitor 470 25V Electrolytic
D2 9JG0034038341 AE J Diode EC8FS6
! D701 9JG0034017964 AE J Photo coupler PS2571L1-1
! D710 9JG0034016135 AM J Rectifier Stack D5SBA60
D711 9JG0034003289 AD J Diode S5688J
D712 9JG0034003289 AD J Diode S5688J
D713 9JG0034038392 AF J Diode RM3A
D714 9JG0034004668 AB J Diode 1SS133
D715 9JG0034039208 AK J Rectifier Stack FMX-G26S
D719 9JG0034004668 AB J Diode 1SS133
D720 9JG0034004668 AB J Diode 1SS133
D721 9JG0034007284 AC J Zener Diode MTZ J18B
D722 9JG0034008922 AC J Zener Diode MTZ J6.8
D723 9JG0034004668 AB J Diode 1SS133
D724 9JG0034004056 AC J Diode DAN202K
D725 9JG0034004668 AB J Diode 1SS133
38
RANK MARK DELIVERY

D729 9JG0034004668 AB J Diode 1SS133
D733 9JG0034004668 AB J Diode 1SS133
D734 9JG0034021902 AC J Zener Diode MTZJ10
D735 9JG0034012377 AC J Zener Diode MTZ J22
D736 9JG0034011974 AB J Diode 1SS244
D737 9JG0034019363 AD J Diode 10ERB20
D738 9JG0034011974 AB J Diode 1SS244
D740 9JG0034009686 AE J Diode SARS02
D741 9JG0034009686 AE J Diode SARS02
D743 9JG0034004668 AB J Diode 1SS133
D744 9JG0034004668 AB J Diode 1SS133
D745 9JG0034004668 AB J Diode 1SS133
D746 9JG0034004668 AB J Diode 1SS133
D750 9JG0034168326 AN J Rectifier Stack FCH20A20
D753 9JG0034004668 AB J Diode 1SS133
D756 9JG0034011974 AB J Diode 1SS244
D757 9JG0034067198 AK J Rectifier Stack FCH20A10
D758 9JG0034003580 AG J Rectifier Stack FMX-G12S
D759 9JG0034083398 AD J Diode EU02
D760 9JG0034002967 AD J Diode 1SS226
D766 9JG0034004668 AB J Diode 1SS133
D767 9JG0034004668 AB J Diode 1SS133
D772 9JG0034004668 AB J Diode 1SS133
D775 9JG0034004668 AB J Diode 1SS133
D777 9JG0034004668 AB J Diode 1SS133
D779 9JG0034004668 AB J Diode 1SS133
D781 9JG0034004668 AB J Diode 1SS133
D786 9JG0034004668 AB J Diode 1SS133
D787 9JG0034004668 AB J Diode 1SS133
D791 9JG0034004668 AB J Diode 1SS133
D794 9JG0034016607 AG J Rectifier Stack FMB-G14L
D801 9JG0034011974 AB J Diode 1SS244
D804 9JG0034073511 AE J Diode SFPM-52
D806 9JG0034036888 AE J Diode SFPX-63
D807 9JG0034064946 AD J Diode AG01Z
! F701 9JG0034088292 AE J Ceramic Fuse AC250V 6.3A
FB701 9JG0034018456 AC J Ferrite Bead BL02RN1
FB702 9JG0034027765 AB J Ferrite Bead G5BT 3X2X1
IC701 9JG0034037760 AL J IC MC33262D
IC702 9JG0034050953 AR J IC STR-W6765
IC703 9JG0034020736 AG J IC AN1431T
IC704 9JG0034020736 AG J IC AN1431T
IC705 9JG0034050279 AL J IC SI-3010KF
IC708 9JG0034159041 AM J IC SI-8008HFE
IC709 9JG0034020736 AG J IC AN1431T
IC710 9JG0034067929 AG J IC PC393G2
JW142 9JG0034033900 AB J Resistor 1 1/2W Metal Oxide
! L701 9JG0034129630 AQ J Reactor DRB25-03A-133NP
! L702 9JG0034129630 AQ J Reactor DRB25-03A-133NP
39
RANK MARK DELIVERY

! L703 9JG0034110999 AM J Reactor HK-10S080-1210
! L704 9JG0037172111 AS J Reactor EXZ40790-204
L705 9JG0034027358 AE J Reactor 270mA 22H
L706 9JG0034027358 AE J Reactor 270mA 22H
L708 9JG0030600150 AF J Reactor CX40357-005
L709 9JG0034063702 AL J Reactor HK-10S100-4500
L710 9JG0030600150 AF J Reactor CX40357-005
LA 9JG0034062420 AF J Connector B6P-VH
PA 9JG0034132844 AQ J Connector TWG-P23P-A1
PB 9JG0034028508 AH J Connector TWG-P9P-A1
PC 9JG0034075476 AG J Connector TWG-P7P-A1
PCB1 9JG0034170177 J Printed Board PSC10189
PCB3 9JG0034121052 J Printed Board PDC20384
PL 9JG0034094713 AG J Connector B04B-PASK-1
PN1 9JG0034007837 AA J Lead Frame CXA40000-505 A
Q701 9JG0034008523 AC J Transistor DTA143EKA
Q702 9JG0034003351 AE J Transistor 2SC2655
Q703 9JG0034000697 AE J Transistor 2SA1020
Q704 9JG0034095167 AP J FET RDX100N60
Q705 9JG0034095167 AP J FET RDX100N60
! Q707 9JG0034075387 AQ J FET 2SK3687
! Q708 9JG0034075387 AQ J FET 2SK3687
Q710 9JG0034027978 AE J FET 2SK2731
Q711 9JG0034004072 AC J Transistor 2SC2412K
Q713 9JG0034027978 AE J FET 2SK2731
Q714 9JG0034027455 AC J Transistor 2SA1037AK
Q718 9JG0034031703 AG J Transistor 2SC3852A
Q721 9JG0034000239 AB J Transistor 2SC1815
Q726 9JG0034095337 AP J FET 2SK2421
Q727 9JG0034003351 AE J Transistor 2SC2655
Q729 9JG0034065152 AC J Transistor DTC114EKA
Q731 9JG0034050309 AN J FET 2SK3659
Q750 9JG0034027978 AE J FET 2SK2731
Q751 9JG0034009139 AH J FET 2SK2865
R7 9JG0034051852 AA J Resistor 4.7 1/8W Chip
R9 9JG0034025401 AA J Resistor 100 1/10W Chip
R13 9JG0034048401 AA J Resistor 2.2k 1/10W Chip
R15 9JG0034025630 AA J Resistor 22k 1/10W Chip
! R701 9JG0034017883 J Resistor 1M 1/2W Special Power
! R702 9JG0034066817 AF J Resistor 3.9M 1W Special Power
! R703 9JG0034066817 AF J Resistor 3.9M 1W Special Power
R705 9JG0034015139 AB J Resistor 470k 1/2W Special Power
R708 9JG0034001472 AA J Resistor 470k 1/4W Carbon
R713 9JG0034001359 AA J Resistor 470 1/4W Carbon
R721 9JG0034033900 AB J Resistor 1 1/2W Metal Oxide
R722 9JG0034002622 J Resistor 47 1/2W Metal Oxide
R723 9JG0034014957 AB J Resistor 22 1W Metal Oxide
R724 9JG0034014957 AB J Resistor 22 1W Metal Oxide
40
RANK MARK DELIVERY

R726 9JG0034066906 AE J Resistor 0.1 3W Metal Oxide
R727 9JG0034152713 AC J Resistor 820k 1/2W Special Power
R732 9JG0034028141 AB J Resistor 680K 1/2W Special Power
R733 9JG0034161798 AC J Resistor 560K 1/2W Special Power
R740 9JG0034001898 AB J Resistor 0.22 1/2W Metal Oxide
R751 9JG0034001405 AA J Resistor 4.7k 1/4W Carbon
R753 9JG0034001421 AD J Resistor 10k 1/4W Carbon
R778 9JG0034073473 AB J Resistor 1.5k 1/10W Chip
R781 9JG0034031185 AC J Resistor 0.33 2W Metal Oxide
R787 9JG0034033897 AB J Resistor 1k 1/2W Metal Oxide
R790 9JG0034053065 AB J Resistor 0.22 1W Metal Oxide
R792 9JG0034083797 AD J Resistor 22 3W Metal Oxide
R804 9JG0034036586 AC J Resistor 10k 1W Metal Oxide
R805 9JG0034003920 AA J Resistor 0 1/10W - 560 1/10W Chip
R810 9JG0023179567 J Short
41
RANK MARK DELIVERY

! RL701 9JG0034160953 AK J Relay SDT-S-118DMR
! SC701 9JG0034078424 AL J Receptacle CCT2302-0711
! T701 9JG0037172103 BA J Transformer EXT45841-407
! T702 9JG0037172081 AY J Transformer EXT41641-408
TH701 9JG0034022038 AF J Thermistor SCK15086M
TK701 9JG0034139466 AD J Sheet Metal Fitting APE46100-538
! VA701 9JG0034054207 AF J Surge Absorber ERZV10D471
! VA702 9JG0034054207 AF J Surge Absorber ERZV10D471
Z1 9JG0034037736 AS J IC SPF9001
N 9JG0034023484 J Rivet CXA40000-505 A, x2 (GROMMET1/2)
N 9JG0034098026 AG J Sheet Metal Fitting APC42200-541 B
N 9JG0034114838 AC J Sheet Metal Fitting APB46400-505 A
N 9JG0034015775 AD J Sheet Metal Fitting, x2
N 9JG0034114773 AC J Sheet Metal Fitting APB46400-506 A
N 9JG0034168601 AP J Heat Sink APH34000-709-3 A
N 9JG0034161372 AL J Heat Sink, x2
N 9JG0034164983 AL J Heat Sink APH44000-873-3 A, x2
42
RANK MARK DELIVERY

N 9JG0034164991 AK J Heat Sink APH44000-876-3 A
N 9JG0034017611 AA J Screw CXA40000-505 A, x11
N 9JG0034031983 AB J Screw CXA40000-505 A, x4
N 9JG0034114846 AC J Name Plate
43
[12] CABINET PARTS
62 3
78 37 74
3-1
1-8 3-2
1-8 77
1-1 77 63
1 1-8 34
11 37 3-3
1-8 78 77
66
1-8 3-4
1-7
74
1-9 1-10 77
27
86
77
1-4
1-3 1-11 10
1-9 1-5 74
1-2
87
36
52 91
82
41
49
80 45
46 53
79 1-6
84
12 49
61 24 2-1
73 42 2
75
19 60 45
81 48 84
75 64
27 18
88 74
27 19
50
28 65
39 32
58
68
35
81
81 77 87
18 88
39 18 36
91
5 81
18 82
2
21-3
81 2-1
21 90
39
39 72
21-2 21-1 82
90
9 21-1
77
21-3
69 81 88
13
16
90
90 40 21-2 15
57 15
32 20
31 32 81
70 6
81 16
75 8
82
27 30
56 81 33
26 90
20 38
82 90 43
44
29 7 17 89 47
25 4-1
51
83 4 54
55
4-2 59
67 85
75
76
14
86
29 4-4
4-3
44

RANK MARK DELIVERY
[12] CABINET PARTS

1 CCABAB740WJ02 BV N S Front Cabinet Ass'y (46XL1E/RU)
1 CCABAB739WJ02 BV N S Front Cabinet Ass'y (52XL1E/RU)
1-1 - - - Front Cabinet
1-2 - - - Center Dec. Cover
1-3 - - N - Front Cover (46XL1E/RU)
1-3 - - N - Front Cover (52XL1E/RU)
1-4 - - - LED Dec.
1-5 - - - Center LED Dec.
1-6 - - - Shine Trim (46XL1E/RU)
1-6 - - - Shine Trim (52XL1E/RU)
1-7 - - - Speaker Net (46XL1E/RU)
1-7 - - - Speaker Net (52XL1E/RU)
1-8 PSPAHA886WJZZ AD J Masking Himelon, x6 (46XL1E/RU)
1-8 PSPAHA884WJZZ AD J Masking Himelon, x6 (52XL1E/RU)
1-9 - - N - Cover Tape (330*40), x4 (46XL1E/RU)
1-11 - - N - Cover Tape (Hole), x2 (46XL1E/RU)
1-11 - - N - Cover Tape (Hole), x2 (52XL1E/RU)
2 CCABBA947WJ01 BR S Rear Cabinet Ass'y (46XL1E/RU)
2 CCABBA948WJ01 BS S Rear Cabinet Ass'y (52XL1E/RU)
2-1 - - N - Rear Cabinet
3 CCOVAB923WJ01 - S Top Cover Ass'y
3-1 - - N - Top Cover
3-2 JBTN-A615WJKA AG N J Button, Control
3-3 DUNTKD910FM01 AH N R KEY Unit
3-4 XEBS930P10000 AA J Screw, x2
4 CDAi-A358WJ03 - N S Stand Ass'y
4-1 - - - Stand Support Ass'y x 2
4-2 - - - Stand Base Ass'y
4-3 - - - Screw x 6
4-4 - - - Screw x 4
5 R1LK460D3LZ2CY N J 46" LCD Panel Module (46XL1E/RU)
5 R1LK520D3LZ2CY N J 52" LCD Panel Module (52XL1E/RU)
6 DUNTKE191FM01 CB N R MAIN Unit
7 DUNTKD604FM11 BL N R AV Unit
8 DUNTKD628FM20 BV N R DIGITAL Unit
9 DUNTKD984FM03 - N S D-TUNER Unit (NOT REPLACEMENT ITEM)
10 DUNTKD909FM01 AU N R R/C, LED Unit
11 DUNTKD888FM02 AG N R ILLUMINATION Unit
12 DUNTKE046FE02 CC N J FRC Unit
13 RDENCA229WJQZ CC N R POWER Unit
14 GCOVAB586WJKA - S PC Card Cover
15 GCOVAB924WJKA AM S Bottom Cover Front x 2
16 GCOVAB925WJKA AL S Bottom Cover Rear x 2
17 LANGFA376WJSA - S Terminal Angle
18 LANGKA801WJFW AH J LCD Side Angle x4
19 LANGKB012WJFW - S FRC Angle, x2
20 LANGTA361WJN1 AN J Stand Angle x 2
21 CANGTA363WJ03 - N S Center Angle Ass'y (46XL1E/RU)
21 CANGTA359WJ02 - N S Center Angle Ass'y (52XL1E/RU)
21-1 - - N - Center Angle, x2
21-2 - - N - LCD Angle (C), x2
21-3 XBBS740P08000 AA J Screw x 8
24 LANGTA463WJM1 - N S FRC Cover
25 LCHSMA384WJFW - N S Chassis Tray
26 LHLDF1206CEKZ - S Wire Holder (Power), x3
27 LHLDW1033CE00 AA J Wire Holder (LC), x2 (46XL1E/RU)
27 LHLDW1033CE00 AA J Wire Holder (LC), x4 (52XL1E/RU)
28 LHLDW1155CEZZ AD J Wire Holder (LVDS) (46XL1E/RU)
28 LHLDW1155CEZZ AD J Wire Holder (LVDS), x3 (52XL1E/RU)
29 LHLDWA031WJKZ AC J Wire Holder (Chassis Tray), x3
30 LHLDWA055WJKZ AC J Wire Holder (LB)
31 LHLDWA059WJKZ AC J Wire Holder (LA)
32 LHLDWA092WJZZ AB J Wire Holder, x4 (KM/RA,SP)
33 LHLDWA123WJKZ AB J Wire Holder (PL,D)
34 LHLDWA137WJZZ AB J Wire Holder, x2 (KM)
35 LHLDWA141WJZZ AD J Wire Holder, x4 (LV,SP,RA)
36 LX-BZA170WJF9 - N S Screw (Rear Cabinet), x4
37 LX-HZA003WJFN AC J Screw (Speaker), x2
38 PCOVPA048WJZZ - N S Tray Cover Sheet
39 PFLT-A004WJZZ AE J Gasket Panel, x4
40 PMLT-A165WJZZ AF J Gasket (W15*H25*L40), x2 (46XL1E/RU)
40 PMLT-A165WJZZ AF J Gasket (W15*H25*L40) (52XL1E/RU)
41 PMLT-A263WJZZ AK J Gasket (POWER), x2
42 PMLT-A309WJZZ AD J Gasket (FRC Shield)), x1
43 PMLT-A381WJZZ - S Gasket (W10*H17*L300), x2
44 PMLT-A382WJZZ - S Gasket (W10*H17*L220)
45 PMLT-A385WJZZ AE J Gasket (W10*H4*L50),x4 (FRC Angle 2/Other 2)
46 PMLT-A386WJZZ AG J Gasket (W10*H7*L100) (FRC Shield 1/Other 1)
47 PMLT-A389WJZZ AK J Gasket (W15*H17*L140)
48 PMLT-A455WJZZ - N S Gasket (FRC Shield)
49 PMLT-A456WJZZ - N S Gasket, x2 (FRC Angle) (46XL1E/RU)
49 PMLT-A456WJZZ - N S Gasket, x4 (FRC Angle) (52XL1E/RU)
45
RANK MARK DELIVERY
[12] CABINET PARTS

50 PSLDMA472WJZZ AF J Gasket (FRC Shield)
51 PSLDMA584WJZZ AE J Gasket (T Angle) (52XL1E/RU)
52 PSLDMA633WJZZ AL J Tape (FRC Shield)
53 PSLDMA850WJZZ AD J Gasket, x2 (FRC Shield)
54 PSLDMA895WJZZ AG J Shield Case
55 PSLDMB055WJFW - S Main Shield
56 PSLDMB145WJFW - N S Full Shield
57 PSLDMB174WJZZ - N S Tape (Main Shield)
58 PSPAHA975WJZZ - N S Spacer, x1 (Back Light Chassis) (46XL1E/RU)
59 PSPAZA872WJKZ AN J Cooling Sheet (IC3002)
60 PSPAZA886WJKZ AC J Spacer (FRC:IC6001 COOL)
61 PSPAZA917WJKZ AH J Spacer (FRC:IC5801 COOL)
62 QCNW-E855WJQZ - N S Connecting Cord (SP:AV-SPR/SPL) (46XL1E/RU)
62 QCNW-F045WJQZ - N S Connecting Cord (SP:AV-SPR/SPL) (52XL1E/RU)
63 QCNW-E857WJQZ - S Connecting Cord (KM:KEY-MAIN) (46XL1E/RU)
63 QCNW-F047WJQZ - N S Connecting Cord (KM:KEY-MAIN) (52XL1E/RU)
64 QCNW-F050WJQZ - N S Connecting Cord (LV:MAIN-TCON)
65 QCNW-F365WJQZ AG J Connecting Cord (FL:LCDCON-FRC)
66 QCNW-F809WJQZ - N S Connecting Cord (RA:MAIN-RC) (46XL1E/RU)
66 QCNW-F813WJQZ - N S Connecting Cord (RA:MAIN-RC) (52XL1E/RU)
67 QCNW-F810WJQZ - N S Connecting Cord (LB:MAIN-INV) (46XL1E/RU)
67 QCNW-F814WJQZ - N S Connecting Cord (LB:MAIN-INV) (52XL1E/RU)
68 QCNW-F811WJQZ - N S Connecting Cord (LF:FRC-MAIN)
69 QCNW-F812WJQZ - N S Connecting Cord (POWER-LCD_C)
70 QCNW-F876WJQZ - N S Connecting Cord (LA:POW-INV) (46XL1E/RU)
70 QCNW-F048WJQZ - N S Connecting Cord (LA:POW-INV) (52XL1E/RU)
72 QEARZA103WJFW - N S Earth Angle
73 QPWBHE107WJQZ AT J FPC, x2 (FRC-LCDCON)
74 RCORF0103CEZZ AK J Core, x4 (SP,2RA,LV)
75 RCORFA012WJZZ AG J Core, x2 (LA, LC) (46XL1E/RU)
75 RCORFA012WJZZ AG J Core (LC) (52XL1E/RU)
76 RCORFA020WJZZ AQ J Core (LB, LC) (46XL1E/RU)
77 RCORFA023WJZZ AK J Core, x7 (2RA, SP/KM_LF_PL) (46XL1E/RU)
77 RCORFA023WJZZ AK J Core, x8 (2RA, 2SP/KM_LF_PL) (52XL1E/RU)
78 RSP-ZA201WJZZ BA J Speaker, x2
79 TLABZB441WJZZ - N S POP Label_100 (46XL1E, 52XL1E)
79 TLABZB571WJZZ - N S POP Label_100 (46XL1RU, 52XL1RU)
80 TLABZB511WJZZ - N S POP Label (46XL1E, 52XL1E)
80 TLABZB572WJZZ - N S POP Label (46XL1RU, 52XL1RU)
81 XBBS740P08000 AA J Screw x 24 (for LCD/Stand Angle)
82 XBBS830P06000 AA J Screw, x12 (for CHS TRY_CAB-B)
83 XBBS930P04000 AA J Screw (for Tuner)
84 XBPS730P06WS0 AA J Screw, x8 (FRC Angle & Shield)
85 XBPS830P06000 AA J Screw, x2 (for HDMI)
86 XEBS930P10000 AA J Screw, x4 (for LED PWB1/VIDEO Jack 3)
87 XEBS940P20000 AB J Screw, x13 (Rear Cabinet) (46XL1E/RU)
87 XEBS940P20000 AB J Screw, x18 (Rear Cabinet) (52XL1E/RU)
88 XEBSN40P10000 AB J Screw, x6 (for PANEL CAB_A) (46XL1E/RU)
88 XEBSN40P10000 AB J Screw, x4 (for PANEL CAB_A) (52XL1E/RU)
89 XJPS730P06WS0 AB J Screw, x2 (Terminal Angle)
90 XJPS730P08WS0 AA J Screw x 18 (for Terminal Angle 8/PWB 10)
91 DLAB-A937WE01 - S Printed Model Label (46XL1E)
91 DLAB-A939WE01 - S Printed Model Label (46XL1RU)
91 DLAB-A940WE01 - S Printed Model Label (52XL1E)
91 DLAB-A942WE01 - S Printed Model Label (52XL1RU)
46
X1 X5 X14 X2
X4
X6
X3 X7
X10 X8
X11 X9
X12
X13

RANK MARK DELIVERY

! X1 QACCBA073WJPZ AV N S AC Cord for U.K.
! X1 QACCKA021WJPZ AT S AC Cord for EUROPE without U.K.
X2 QCNWGA075WJPZ AU J 3 RCA to 15pin D-sub Adaptor
X3 RRMCGA588WJSA BQ N S Remote Control Unit
X4 LHLDWA012WJKZ AC J Cable Clamp, x2
X5 LHLDWA083WJ00 AC J Cable Band
X6 LHLDWA131WJKZ AE J Cable Clamp
X7 TGAN-A077WJZZ AD N J Warranty Card (LC-46/52XL1RU)
X8 TGAN-A801WJZZ - N S Warranty Card (LC-46/52XL1E)
X9 TGAN-A802WJZZ - N S AQUOS Care Plan (LC-46/52XL1E)
X10 TiNS-D104WJZZ BA N S Operation Manual (ENGLISH)
X11 TiNS-D105WJZZ BA N S Operation Manual (SWEDISH)
X12 TiNS-D106WJZZ BC N S Operation Manual (POLISH)
X13 TINS-D107WJZZ - N S Operation Manual (RUSSIAN)
X14 CDAI-A358WJ03 - N S Stand Ass'y
47
[14] PACKING PARTS (NOT REPLACEMENT ITEM)
S3
S9
S9
S8
S7
S5
S7
S1
S4
S10
S7
S6
S7
S2
48

RANK MARK DELIVERY
[14] PACKING PARTS (NOT REPLACEMENT ITEM)

S1 SPAKCD472WJZZ - N - Packing Case (Top) (LC-46XL1E)
S1 SPAKCD543WJZZ - N - Packing Case (Top) (LC-46XL1RU)
S1 SPAKCD474WJZZ - N - Packing Case (Top) (LC-52XL1E)
S1 SPAKCD544WJZZ - N - Packing Case (Top) (LC-52XL1RU)
S2 SPAKCD473WJZZ - N - Packing Case (Bottom) (LC-46XL1E/RU)
S2 SPAKCD475WJZZ - N - Packing Case (Bottom) (LC-52XL1E/RU)
S3 SPAKFB252WJZZ - N - Top Pad (LC-46XL1E/RUU)
S3 SPAKFB253WJZZ - N - Top Pad (LC-52XL1E/RUU)
S4 SPAKPA711WJZZ - - Wrapping Paper (LC-46XL1E/RU)
S4 SPAKPA712WJZZ - - Wrapping Paper (LC-52XL1E/RU)
S5 SPAKXB514WJZZ - N - EPS Center Top (LC-46XL1E/RU)
S5 SPAKXB516WJZZ - N - EPS Center Top (LC-52XL1E/RU)
S6 SPAKXB515WJZZ - N - EPS Center Bottom (LC-46XL1E/RU)
S6 SPAKXB517WJZZ - N - EPS Center Bottom (LC-52XL1E/RU)
S7 SPAKXB518WJZZ - N - EPS Top Pad (LC-46XL1E/RU)
S7 SPAKXB519WJZZ - N - EPS Top Pad (LC-52XL1E/RU)
S8 SSAKAA009WJZZ - - Polyethylene Bag
S9 SSAKAA010WJZZ - - Polyethylene Bag
S10 DLAB-A937WE01 - S Printed Case No Label (LC-46XL1E)
S10 DLAB-A939WE01 - S Printed Case No Label (LC-46XL1RU)
S10 DLAB-A940WE01 - S Printed Case No Label (LC-52XL1E)
S10 DLAB-A942WE01 - S Printed Case No Label (LC-52XL1RU)
[15] SERVICE JIGS (USE FOR SERVICING)
N QCNW-C222WJQZ AW J Extension Cable 80pins FFC L=1000mm, LCD Cont. to LCD Panel Unit, x2
N QCNWF-042WJQZ AS J Extension Cable, Power Unit to Inverter Unit, x2
N QCNWKA011WJZZ BH S Extension Cable for Digital Unit
N QCNWGA015WJPZ AK J Interface Cable L=165mm, 9pin D-sub - Mini DIN (AN-A1RS)
N QCNWKA012WJZZ BP S Digital Software Writing Jig
49
COPYRIGHT 2007 BY SHARP CORPORATION
ALL RIGHTS RESERVED.
No Part of this publication may be reproduced,

stored in a retrieval system, or transmitted in
any from or by any means, electronic, mechanical,
photocopying, recording, or otherwise, without
prior written permission of the publisher.
SHARP CORPORATION
AV Systems Group
Jun. 2007 Printed in Japan CS Promotion Center
TQ2177-S SH. DS Yaita,Tochigi 329-2193, Japan

Sharp LC-46XL1E PDF

Uploaded by

Copyright:

Available Formats

Sharp LC-46XL1E PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Sharp LC-46XL1E PDF

Uploaded by

Copyright:

Available Formats

LC-46XL1E/RU, LC-52XL1E/RU

LCD COLOUR TELEVISION

CHAPTER 1. OPERATION MANUAL CHAPTER 7. PRINTED WIRING BOARD

This document has been published to be used for

IMPORTANT SERVICE SAFETY PRECAUTION

Employing lead-free solder

Using lead-free wire solder

Remote control unit

(1137.0 ) / [1273.0] (96.0 ) / [95.0] (124.4 ) / [125.5]

[1] REMOVING OF MAJOR PARTS (LC-46XL1E/RU)

2. Remove the 4 lock screws 4 and detach the Bottom Cover.

Bottom Cover -Rear

< Check >

4. Remove the 8 lock screws 7 and detach the Stand Angle.

# In stand angle installation, position while

When install center angle, be careful

Center Angle Ass'y

Don't sandwich wire "SP"

6. Remove the KM connectors from the KEY PWB.

Wire "KM" (to P151) Top Cover Ass'y

Wire "SP" Wire "SP", "RA" into Edge

# Push slack of Wire "SP" into Full-

8. Remove the SP wire from the wire holders.

For prevention to sandwich between molding parts

Ferrite Core (to SP-Box Wire "L")

Wire "SP" to pin

Remove the 2 lock screws 12 and detach the Speaker L & R.

Wire "SP" (to P301) Wire "RA","SP" to WH SP Box SP Box

Ferrite Core (to Wire "SP")

Wire "RA" (to P2303)

Ferrite Core (to Wire "RA")

R/C, LED Unit

Wire "RA" (to P101)

Wire "RA" to pin

# Shape like this

Shape wire "RA" to pin inside

Ferrite Core (to Wire "RA")

< Detail "A" >

# to Wire "LC" and "LB" # to Wire "LC"

Ferrite Core Ferrite Core

Wire "LA" (to CN7401) Wire "LA" (to CN7601)

Wire "LV" (SC2302 to SC6281)

Chassis Tray Sub Ass'y

FRC Unit FRC Angle

LCD Side Angle

Wire "LF (D)"

B to B connector (to SC2705 / SC2707)

2. Remove the 4 lock screws 4 and detach the Bottom Cover.

4. Remove the 8 lock screws 7 and detach the Stand Angle.

Center Angle Ass'y

< CAUTIONS > "TOP" Printing

7. Remove the SP wire.

Remove the 2 lock screws 9 and detach the Speaker L & R.

< CAUTIONS >

Detach wire "SP".

Wire "RA","SP" to pin of cabinet

8. Remove the 4 lock screws 10 and detach the FRC Cover.

9. Remove all the connectors from PWBs.

#Connect to FRC UNIT