H156-E1-03 E5 - N UsersManual

E5CN
E5AN
E5EN
E5EN
E5GN
E5GN
Digital Temperature Controllers
SUB1 SUB1 SUB2
SUB2
PV HA SUB3
SUB3
PV
HA
SV
SV
OUT1 STOP
MV OUT1 STOP MV
OUT2 CMW MANU OUT2 CMW MANU
PF
A/M
PF
A/M
E5AN E5EN
User's Manual
Basic Type
Cat. No. H156-E1-03
E5CN/E5AN/E5EN/E5GN
Digital Temperature Controllers
Users Manual
Basic Type
Revised September 2009
iv
Preface
The E5CN, E5CN-U, E5AN, E5EN, and E5GN are Digital Temperature Controllers. The E5CN and
E5CN-U are both compact temperature controllers, with the E5CN featuring screw terminal connec-
tions, and the E5CN-U featuring socket pin connections. The E5GN can be connected using screw ter-
minals or screwless clamp terminals. The main functions and characteristics of these Digital
Temperature Controllers are as follows:
Any of the following types of input can be used: thermocouple, platinum
resistance thermometer, infrared sensor, analog voltage, or analog cur-
rent.
Either standard or heating/cooling control can be performed.
Both auto-tuning and self-tuning are supported.
Event inputs can be used to switch set points (multi-SP function), switch
between RUN and STOP status, switch between automatic and manual
operation, start/reset the simple program function, and perform other
operations. (Event inputs are not applicable to the E5CN-U.)
Heater burnout detection, heater short (HS) alarms, and heater overcur-
rent (OC) functions are supported. (Applicable to E5CN, E5AN, E5EN,
and E5GN models with heater burnout detection function.)
Communications are supported. (Applicable to E5CN, E5AN, E5EN, and
E5GN models with communications.)
User calibration of the sensor input is supported.
The structure is waterproof (IP66). (Not applicable to the E5CN-U.)
Conforms to UL, CSA, and IEC safety standards and EMC Directive.
The PV display color can be switched to make process status easy to
understand at a glance.
This manual describes the E5CN, E5CN-U, E5AN, E5EN, and E5GN. Read this manual thoroughly
and be sure you understand it before attempting to use the Digital Temperature Controller and use the
Digital Temperature Controller correctly according to the information provided. Keep this manual in a
safe place for easy reference. Refer to the following manual for further information on communications:
E5CN/E5AN/E5EN/E5GN Digital Temperature Controllers Communications Manual Basic Type (Cat.
No. H158).
Refer to the following manual for information on the Advanced Type Controllers: E5CN/E5AN/E5EN-H
Digital Temperature Controllers User's Manual Advanced Type (Cat. No. H157).
Visual Aids
The following headings appear in the left column of the manual to help you locate different types of
information.
Note Indicates information of particular interest for efficient and convenient opera-
tion of the product.
1,2,3... 1. Indicates lists of one sort or another, such as procedures, checklists, etc.
v
OMRON, 2008
All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form, or
by any means, mechanical, electronic, photocopying, recording, or otherwise, without the prior written permission of
OMRON.
No patent liability is assumed with respect to the use of the information contained herein. Moreover, because OMRON is con-
stantly striving to improve its high-quality products, the information contained in this manual is subject to change without
notice. Every precaution has been taken in the preparation of this manual. Nevertheless, OMRON assumes no responsibility
for errors or omissions. Neither is any liability assumed for damages resulting from the use of the information contained in
this publication.
vi
Read and Understand this Manual
Please read and understand this manual before using the products. Please consult your OMRON
representative if you have any questions or comments.
Warranty, Limitations of Liability

WARRANTY
OMRON's exclusive warranty is that the products are free from defects in materials and workmanship for a
period of one year (or other period if specified) from date of sale by OMRON.
OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, REGARDING NON-
INFRINGEMENT, MERCHANTABILITY, OR FITNESS FOR PARTICULAR PURPOSE OF THE PRODUCTS. ANY
BUYER OR USER ACKNOWLEDGES THAT THE BUYER OR USER ALONE HAS DETERMINED THAT THE
PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE. OMRON DISCLAIMS ALL
OTHER WARRANTIES, EXPRESS OR IMPLIED.
LIMITATIONS OF LIABILITY
OMRON SHALL NOT BE RESPONSIBLE FOR SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES,
LOSS OF PROFITS OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS,
WHETHER SUCH CLAIM IS BASED ON CONTRACT, WARRANTY, NEGLIGENCE, OR STRICT
LIABILITY.
In no event shall the responsibility of OMRON for any act exceed the individual price of the product on which
liability is asserted.
IN NO EVENT SHALL OMRON BE RESPONSIBLE FOR WARRANTY, REPAIR, OR OTHER CLAIMS
REGARDING THE PRODUCTS UNLESS OMRON'S ANALYSIS CONFIRMS THAT THE PRODUCTS
WERE PROPERLY HANDLED, STORED, INSTALLED, AND MAINTAINED AND NOT SUBJECT TO
CONTAMINATION, ABUSE, MISUSE, OR INAPPROPRIATE MODIFICATION OR REPAIR.
Application Considerations
SUITABILITY FOR USE
OMRON shall not be responsible for conformity with any standards, codes, or regulations that apply to the
combination of the products in the customer's application or use of the products.
At the customer's request, OMRON will provide applicable third party certification documents identifying
ratings and limitations of use that apply to the products. This information by itself is not sufficient for a
complete determination of the suitability of the products in combination with the end product, machine,
system, or other application or use.
The following are some examples of applications for which particular attention must be given. This is not
intended to be an exhaustive list of all possible uses of the products, nor is it intended to imply that the uses
listed may be suitable for the products:
Outdoor use, uses involving potential chemical contamination or electrical interference, or conditions or
uses not described in this manual.
Nuclear energy control systems, combustion systems, railroad systems, aviation systems, medical
equipment, amusement machines, vehicles, safety equipment, and installations subject to separate
industry or government regulations.
Systems, machines, and equipment that could present a risk to life or property.
Please know and observe all prohibitions of use applicable to the products.
NEVER USE THE PRODUCTS FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR
PROPERTY WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO
ADDRESS THE RISKS, AND THAT THE OMRON PRODUCTS ARE PROPERLY RATED AND INSTALLED
FOR THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM.
PROGRAMMABLE PRODUCTS
OMRON shall not be responsible for the user's programming of a programmable product, or any
consequence thereof.
vii
Disclaimers
CHANGE IN SPECIFICATIONS
Product specifications and accessories may be changed at any time based on improvements and other
reasons.
It is our practice to change model numbers when published ratings or features are changed, or when
significant construction changes are made. However, some specifications of the products may be changed
without any notice. When in doubt, special model numbers may be assigned to fix or establish key
specifications for your application on your request. Please consult with your OMRON representative at any
time to confirm actual specifications of purchased products.
DIMENSIONS AND WEIGHTS
Dimensions and weights are nominal and are not to be used for manufacturing purposes, even when
tolerances are shown.
PERFORMANCE DATA
Performance data given in this manual is provided as a guide for the user in determining suitability and does
not constitute a warranty. It may represent the result of OMRON's test conditions, and the users must
correlate it to actual application requirements. Actual performance is subject to the OMRON Warranty and
Limitations of Liability.
ERRORS AND OMISSIONS
The information in this manual has been carefully checked and is believed to be accurate; however, no
responsibility is assumed for clerical, typographical, or proofreading errors, or omissions.
viii
Safety Precautions
Definition of Precautionary Information
The following notation is used in this manual to provide precautions required
to ensure safe usage of the product.
The safety precautions that are provided are extremely important to safety.
Always read and heed the information provided in all safety precautions.
The following notation is used.
Indicates a potentially hazardous situation which, if not

CAUTION avoided, is likely to result in minor or moderate injury or in
property damage.
Symbols
Symbol Meaning
General Caution
Indicates non-specific general cautions, warnings, and
dangers.
Caution
Electrical Shock Caution
Indicates possibility of electric shock under specific
conditions.
General Prohibition
Prohibition
Indicates non-specific general prohibitions.
General Caution
Mandatory
Indicates non-specific general cautions, warnings, and
Caution
dangers.
ix
Safety Precautions
CAUTION
Do not touch the terminals while power is being supplied.

Doing so may occasionally result in minor injury due to electric
shock.
Do not allow pieces of metal, wire clippings, or fine metallic shav-

ings or filings from installation to enter the product. Doing so may
occasionally result in electric shock, fire, or malfunction.
Do not use the product where subject to flammable or explosive

gas. Otherwise, minor injury from explosion may occasionally
occur.
Never disassemble, modify, or repair the product or touch any of

the internal parts. Minor electric shock, fire, or malfunction may
occasionally occur.
CAUTION - Risk of Fire and Electric Shock

a) This product is UL listed as Open Type Process Control Equip-
ment. It must be mounted in an enclosure that does not allow
fire to escape externally.
b) More than one disconnect switch may be required to de-
energize the equipment before servicing the product.
c) Signal inputs are SELV, limited energy. *1
d) Caution: To reduce the risk of fire or electric shock, do not inter-
connect the outputs of different Class 2 circuits.*2
If the output relays are used past their life expectancy, contact
fusing or burning may occasionally occur.
Always consider the application conditions and use the output
relays within their rated load and electrical life expectancy. The life
expectancy of output relays varies considerably with the output
load and switching conditions.
*1 A SELV circuit is one separated from the power supply with double insulation or
reinforced insulation, that does not exceed 30 V r.m.s. and 42.4 V peak or
60 VDC.
*2 A class 2 power supply is one tested and certified by UL as having the current
and voltage of the secondary output restricted to specific levels.
x
CAUTION
Tighten the terminal screws to between 0.74 and 0.90 Nm. Loose
screws may occasionally result in fire. *3
Set the parameters of the product so that they are suitable for the
system being controlled. If they are not suitable, unexpected
operation may occasionally result in property damage or
accidents.
A malfunction in the Temperature Controller may occasionally

make control operations impossible or prevent alarm outputs,
resulting in property damage. To maintain safety in the event of
malfunction of the Temperature Controller, take appropriate safety
measures, such as installing a monitoring device on a separate
line.
A semiconductor is used in the output section of long-life relays. If

excessive noise or surge is impressed on the output terminals, a
short-circuit failure is likely to occur. If the output remains shorted,
fire will occur due to overheating of the heater or other cause.
Take measures in the overall system to prevent excessive temper-
ature increase and to prevent fire from spreading.
When inserting the body of the Temperature Controller into the

case, confirm that the hooks on the top and bottom are securely
engaged with the case. If the body of the Temperature Controller
is not inserted properly, faulty contact in the terminal section or
reduced water resistance may occasionally result in fire or mal-
function.
*3 The tightening torque is 0.5 Nm for the E5CN-U and 0.43 to 0.58 Nm for the
E5GN. The terminal torque is 0.5 to 0.6 Nm for auxiliary output 2 on the E5GN.
xi
Precautions for Safe Use
Be sure to observe the following precautions to prevent operation failure, malfunction, or adverse affects on
the performance and functions of the product. Not doing so may occasionally result in unexpected events. Use
the product within the specifications.
1) The product is designed for indoor use only. Do not use the product outdoors or in any of the following
locations. Do not use or store the product in any of the following locations.
Places directly subject to heat radiated from heating equipment.
Places subject to splashing liquid or oil atmosphere.
Places subject to direct sunlight.
Places subject to dust or corrosive gas (in particular, sulfide gas and ammonia gas).
Places subject to intense temperature change.
Places subject to icing and condensation.
Places subject to vibration and large shocks.
2) Use and store the Digital Temperature Controller within the rated ambient temperature and humidity.
Gang-mounting two or more temperature controllers, or mounting temperature controllers above each
other may cause heat to build up inside the temperature controllers, which will shorten their service life. In
such a case, use forced cooling by fans or other means of air ventilation to cool down the Digital
Temperature Controllers.
3) To allow heat to escape, do not block the area around the product. Do not block the ventilation holes on
the product.
4) Be sure to wire properly with correct polarity of terminals.
5) Use the specified size of crimp terminals for the E5CN, E5AN, or E5EN (M3.5, width of 7.2 mm or less).
For open-wired connections to the E5CN, E5AN, or E5EN, use stranded or solid copper wires with a
gauge of AWG24 to AWG14 (equal to a cross-sectional area of 0.205 to 2.081 mm 2). (The stripping
length is 5 to 6 mm.) Up to two wires of the same size and type or two crimp terminals can be connected
to one terminal. Do not connect more than two wires or more than two crimp terminals to the same
terminal.
Use the specified size of crimp terminals for the E5GN (M3.0, width of 5.8 mm or less). For open-wired
connections to the E5GN, use stranded or solid copper wires with a gauge of AWG24 to AWG18 (equal to
a cross-sectional area of 0.205 to 0.8231 mm2). (The stripping length for screw terminals is 6 to 8 mm.
The stripping length for screwless clamp terminals is 10 mm. The stripping length for auxiliary output 2 is
6 mm.) Up to two wires of the same size and type or two crimp terminals can be connected to one
terminal. Do not connect more than two wires or more than two crimp terminals to the same terminal.
Ferrules for screwless clamp terminals must be 0.8 to 1.4 mm in diameter and the exposed conductor
must be 8 to 12 mm in length. Ferrules for auxiliary output 2 must be 0.8 to 1.4 mm in diameter and the
exposed conductor must be 6 mm in length.
6) Do not wire the terminals which are not used.
7) To avoid inductive noise, keep the wiring for the Digital Temperature Controller's terminal block away from
power cables carry high voltages or large currents. Also, do not wire power lines together with or parallel
to Digital Temperature Controller wiring. Using shielded cables and using separate conduits or ducts is
recommended.
Attach a surge suppressor or noise filter to peripheral devices that generate noise (in particular, motors,
transformers, solenoids, magnetic coils or other equipment that have an inductance component).
When a noise filter is used at the power supply, first check the voltage or current, and attach the noise
filter as close as possible to the temperature controller.
Allow as much space as possible between the Digital Temperature Controller and devices that generate
powerful high frequencies (high-frequency welders, high-frequency sewing machines, etc.) or surge.
8) Use this product within the rated load and power supply.
9) Make sure that the rated voltage is attained within two seconds of turning ON the power using a switch or
relay contact. If the voltage is applied gradually, the power may not be reset or output malfunctions may
occur.
xii
10) Make sure that the Temperature Controller has 30 minutes or more to warm up after turning ON the power
before starting actual control operations to ensure the correct temperature display.
11) When executing self-tuning, turn ON power for the load (e.g., heater) at the same time as or before
supplying power to the Digital Temperature Controller. If power is turned ON for the Digital Temperature
Controller before turning ON power for the load, self-tuning will not be performed properly and optimum
control will not be achieved.
12) A switch or circuit breaker should be provided close to this unit. The switch or circuit breaker should be
within easy reach of the operator, and must be marked as a disconnecting means for this unit.
13) Always turn OFF the power supply before removing the body of the E5CN, E5AN, or E5EN from the case,
and never touch nor apply shock to the terminals or electronic components. When inserting the interior of
the product, do not allow the electronic components to touch the case.
Always turn OFF the power supply before removing the terminal block from the E5GN, and never touch
nor apply shock to the terminals or electronic components.
14) Do not use paint thinner or similar chemical to clean with. Use standard grade alcohol.
15) Design system (control panel, etc.) considering the 2 second of delay that the controllers output to be set
after power ON.
16) The output may turn OFF when shifting to certain levels. Take this into consideration when performing
control.
17) The number of EEPROM write operations is limited. Therefore, use RAM write mode when frequently
overwriting data during communications or other operations.
18) Always touch a grounded piece of metal before touching the Digital Temperature Controller to discharge
static electricity from your body.
19) Do not remove the terminal block from the E5CN, E5AN, or E5EN. Doing so may result in failure or
malfunction.
20) Control outputs that are voltage outputs are not isolated from the internal circuits. When using a grounded
thermocouple, do not connect any of the control output terminals to ground. (Doing so may result in an
unwanted circuit path, causing error in the measured temperature.)
21) When replacing the body of the E5CN, E5AN, or E5EN, check the condition of the terminals. If corroded
terminals are used, contact failure in the terminals may cause the temperature inside the E5CN, E5AN, or
E5EN to increase, possibly resulting in fire. If the terminals are corroded, replace the case as well.
When removing the terminal block of the E5GN to replace the Digital Temperature Controller, check the
condition of the terminals. If corroded terminals are used, contact failure in the terminals may cause the
temperature inside the Digital Temperature Controller to increase, possibly resulting in fire. If the terminals
are corroded, replace the terminal block as well.
22) Use suitable tools when taking the Digital Temperature Controller apart for disposal. Sharp parts inside
the Digital Temperature Controller may cause injury.
23) When applying Lloyd's standards, install the Digital Temperature Controller according to the requirements
given in Shipping Standards.
24) Do not use the Temperature Controller if the front sheet is peeling off or torn.
Service Life
Use the Temperature Controller within the following temperature and humidity ranges:
Temperature: 10 to 55C (with no icing or condensation), Humidity: 25% to 85%
If the Controller is installed inside a control board, the ambient temperature must be kept to under
55C, including the temperature around the Controller.
The service life of electronic devices like Temperature Controllers is determined not only by the num-
ber of times the relay is switched but also by the service life of internal electronic components. Compo-
nent service life is affected by the ambient temperature: the higher the temperature, the shorter the
service life and, the lower the temperature, the longer the service life. Therefore, the service life can be
extended by lowering the temperature of the Temperature Controller.
xiii
When two or more Temperature Controllers are mounted horizontally close to each other or vertically
next to one another, the internal temperature will increase due to heat radiated by the Temperature
Controllers and the service life will decrease. In such a case, use forced cooling by fans or other
means of air ventilation to cool down the Temperature Controllers. When providing forced cooling,
however, be careful not to cool down the terminals sections alone to avoid measurement errors.
Ambient Noise
To avoid inductive noise, keep the wiring for the Digital Temperature Controller's terminal block wiring
away from power cables carrying high voltages or large currents. Also, do not wire power lines together
with or parallel to Digital Temperature Controller wiring. Using shielded cables and using separate con-
duits or ducts is recommended.
Attach a surge suppressor or noise filter to peripheral devices that generate noise (in particular,
motors, transformers, solenoids, magnetic coils or other equipment that have an inductance compo-
nent). When a noise filter is used at the power supply, first check the voltage or current, and attach the
noise filter as close as possible to the Temperature Controller.
Allow as much space as possible between the Digital Temperature Controller and devices that gener-
ate powerful high frequencies (high-frequency welders, high-frequency sewing machines, etc.) or
surge.
Ensuring Measurement Accuracy

When extending or connecting the thermocouple lead wire, be sure to use compensating wires that
match the thermocouple types.
When extending or connecting the lead wire of the platinum resistance thermometer, be sure to use
wires that have low resistance and keep the resistance of the three lead wires the same.
Mount the Temperature Controller so that it is horizontally level.
If the measurement accuracy is low, check to see if input shift has been set correctly.
Waterproofing
The degree of protection is as shown below. Sections without any specification on their degree of pro-
tection or those with IP@0 are not waterproof.
Front panel: IP66
Rear case: IP20, Terminal section: IP00
(E5CN-U: Front panel: IP50, rear case: IP20, terminals: IP00)
xiv
Precautions for Operation
1) It takes approximately two seconds for the outputs to turn ON from after the power supply is turned ON.
Due consideration must be given to this time when incorporating Temperature Controllers into a control
panel or similar device.
2) Make sure that the Temperature Controller has 30 minutes or more to warm up after turning ON the power
before starting actual control operations to ensure the correct temperature display.
3) When executing self-tuning, turn ON power for the load (e.g., heater) at the same time as or before
supplying power to the Temperature Controller. If power is turned ON for the Temperature Controller
before turning ON power for the load, self-tuning will not be performed properly and optimum control will
not be achieved. When starting operation after the Temperature Controller has warmed up, turn OFF the
power and then turn it ON again at the same time as turning ON power for the load. (Instead of turning the
Temperature Controller OFF and ON again, switching from STOP mode to RUN mode can also be used.)
4) Avoid using the Controller in places near a radio, television set, or wireless installing. The Controller may
cause radio disturbance for these devices.
Shipping Standards
The E5CN, E5CN-H, E5AN, E5AN-H, E5EN, and E5EN-H comply with Lloyd's standards. When applying the
standards, the following installation and wiring requirements must be met in the application.
Application Conditions
1) Installation Location
The E5CN, E5CN-H, E5AN, E5AN-H, E5EN, and E5EN-H comply with installation category ENV1 and
ENV2 of Lloyd's standards. Therefore, they must be installed in a location equipped with air condition-
ing. They must therefore be installed in a location equipped with air conditioning. They cannot be used
on the bridge or decks, or in a location subject to strong vibration.
2) Wiring Conditions
Install the recommended ferrite core and wrap the line around it three turns for the applicable lines
(e.g., power supply cable line and signal lines) of the models listed in the following table. (See illustra-
tions.) Install the ferrite cores as close to the terminal block of the E5@N as possible. (As a guideline,
the ferrite core should be within 10 cm of the terminal block.)
Lines Requiring Ferrite Cores
Model Signal and power lines provided with ferrite cores
E5CN, E5CN-U, or E5CN-H Input power supply
E5EN, E5AN, E5EN-H, or Input power supply and I/O lines (control outputs (1 and 2), communications,
E5AN-H event inputs (1 to 4), transfer output, and external power supply (Advanced
Type models do not have an external power supply.)
Recommended Ferrite Core

Manufacturer Seiwa Electric Mfg. Co., Ltd.
Model E04RA310190100
xv
Ferrite Core Connection Examples
1. E5CN/E5CN-H
Auxiliary outputs
+ (relay outputs)
1 11 6
Control output 1 Auxiliary output 2
2 12 7
Auxiliary
+ DO NOT DO NOT A output 1
USE USE 3 13 8
mA Power supply
B
4

14 9
Input power
V
B supply AC/DC
DO NOT 5 15 10 3 turns
USE + +
Analog input TC/Pt universal input
2. E5AN/E5EN/E5AN-H/E5EN-H
Event Inputs
Power 3 turns 1 21 11
AC/DC Input power
Connected to
supply supply EV2 communications or
2 22 12 3 turns event inputs 1 and 2.
EV1
+ Control External Power
3 23 13 Supply
Connected to CT1/CT2 Output 2
Control output 1
control output 1. + +
3 turns 4 24 14
Connected to
CT1 Control External power supply
Output 2 12 VDC, 20 mA control output 2
5 25 15 3 turns or external

Auxiliary output 3 CT2 power supply.
DO NOT DO NOT
6 26 16 USE USE
DO NOT
7 27 17 USE
Auxiliary output 2
DO NOT A DO NOT +
8 28 18
USE USE mA
B
9 29 19

Auxiliary output 1 V DO NOT
10 30 20 B
+ + USE
TC/Pt universal input Analog input
Communications
21 RS-232C RS-485
22 11 SD 11 B (+)
12 RD 12 A ()
23
EV3 13 SG 13 DO NOT USE
Connected to event
inputs 3 and 4. 24 21 DO NOT USE 21 B (+)
3 turns EV4
25 22 DO NOT USE 22 A ()
DO NOT USE 26
+
27
Connected to Transfer output
4 to 20 mA DC
transfer output. (Load: 600 max.)
3 turns 28

DO NOT USE 29
DO NOT USE 30
xvi
Preparations for Use
Be sure to thoroughly read and understand the manual provided with the product, and check the fol-
lowing points.
Timing Check point Details
Purchasing the prod- Product appearance After purchase, check that the product and packaging are not dented or
uct otherwise damaged. Damaged internal parts may prevent optimum
control.
Product model and speci- Make sure that the purchased product meets the required specifica-
fications tions.
Setting the Unit Product installation loca- Provide sufficient space around the product for heat dissipation. Do not
tion block the vents on the product.
Wiring Terminal wiring Do not subject the terminal screws to excessive stress (force) when
tightening them.
Make sure that there are no loose screws after tightening terminal
screws to the specified torque of 0.74 to 0.90 Nm (see note).
Be sure to confirm the polarity for each terminal before wiring the termi-
nal block and connectors.
Power supply inputs Wire the power supply inputs correctly. Incorrect wiring will result in
damage to the internal circuits.
Operating environ- Ambient temperature The ambient operating temperature for the product is 10 to 55C (with
ment no condensation or icing). To extend the service life of the product,
install it in a location with an ambient temperature as low as possible. In
locations exposed to high temperatures, if necessary, cool the products
using a fan or other cooling method.
Vibration and shock Check whether the standards related to shock and vibration are satis-
fied at the installation environment. (Install the product in locations
where the conductors will not be subject to vibration or shock.)
Foreign particles Install the product in a location that is not subject to liquid or foreign
particles entering the product.
Note The tightening torque is 0.5 Nm for the E5CN-U and 0.43 to 0.58 Nm for the
E5GN. The terminal torque is 0.5 to 0.6 Nm for auxiliary output 2 on the
E5GN.
xvii
Upgraded Functions
The functionality of the E5CN, E5CN-U, E5AN, and E5EN was improved starting from December 2007
production.
The functionality of the E5GN was improved starting from August 2009 production.
The design of the front panel can be used to differentiate between the previous and upgraded models.
E5CN/CN-U
The upgraded Controllers are basically compatible with the previous Controllers. Terminal
arrangements, terminal sizes, and panel mounting depth have not been changed.
E5AN/EN
Although the upgraded Controllers are compatible with the previous Controllers, terminal arrange-
ments have been changed. Terminal sizes and panel mounting depth have not been changed.
E5GN
Model numbers have changed accompanying the introduction of universal input capability. The
default setting of the input type parameter of the E5GN-@@@P (models with resistance thermom-
eters) has been changed from a Pt100 resistance thermometer to a K thermocouple. Make sure
the setting of the input type parameter agrees with the temperature sensor that is being used.
The terminal block has also been changed, which means the wiring methods and terminal
arrangement are different.
Other changes outlined in the following tables. Refer to relevant pages in the manual for details.
Previous models Upgraded models
E5CN/CN-U
ALM indicator was changed to SUB indicator.

E5AN
Number of displays: 2 (PV and SV) Number of displays: 3 (PV, SV, and MV) *
xviii
E5EN
Number of displays: 2 (PV and SV) Number of displays: 3 (PV, SV, and MV) *
E5GN
Display Segments Display Segments

PV: 7 segments, PV: 11 segments,
SV: 7 segments SV: 11 segments
Character Heights Character Heights
PV: 7 mm, SV: 3.5 mm PV: 7.5 mm, SV: 3.6 mm
Changes to Display Contents
"AL" LED indicator eliminated, LED indicators
added, and key indicator added.
* A 2-level display is set when shipped from the factory.

A 3-level display is activated if parameters are initialized.
xix
Terminal Arrangements
E5AN/EN Terminals 16 through 20 were changed. Terminals 1 through One CT External power
Control Output 2 supply
15 were not changed. Two CTs
+ +
Voltage output Long-life relay External power One CT 14 External power
output supply for ES1B Two CTs CT1 Control Output 2 supply
12 VDC, 20 mA
15
14 + 14
Control Output 2
14 14+ CT2

Control Output 2 12 VDC, 20 mA CT1 DO NOT DO NOT
250 VAC, 3 A
15
12 VDC, 21 mA
15 (Resistive load)
15 15
16 USE USE
CT2 DO NOT
A 17
16 + USE
mA A
+

DO NOT DO NOT
B 18 USE USE
17 B
mA
B
V 19
18 V
+ + 20
B DO NOT
USE
+ +
19 TC/Pt universal input Analog input 19
TC/Pt universal input Analog input

E5GN Number of terminals: 9 (1 to 9) Number of terminals: 14 (1 to 14)
Input terminals: 7 to 9 Input terminals: 10 to 12
RS-485 communications terminals: 5 and 6 RS-485 communications terminals: 7 and 8
RS-485 B(+)
communications DO NOT mA DO NOT
+
USE USE
RS-232C SD RD SG Analog input
V
communications
+
+
DO NOT
Input
power
+ Control B(+) A()
output 1
TC CT input CT DO NOT
USE
USE
supply Communications A B B
Universal TC/Pt input
100 to 240 VAC or 12 VDC 21 mA PT EV2
A B B Event input EV1 DO NOT
+
USE
24 VAC/DC (no polarity)
Relay output Alarm output 1,
7 8 9 10 11 12
+
(OUT1) control output 2,

or input error

Analog
alarm 1/output 1 input 1 2 3 4 5 6 13 14
(ALM1/OUT1)
Auxiliary
Input power Control Auxiliary output 2
supply + output 1 output 1
100 to 240 VAC
24 VAC/DC (no polarity)
xx
Body Drawout
E5AN/EN Using Screws Using Hooks
Dimensions
E5GN 3 100 Models with Screw Terminal Blocks
Bezel thickness: 2 mm
Depth: 99 mm
Shape of slits changed
35
22
2 99
35
22
Depth: 100 mm
Models with Screwless Clamp Terminal Blocks

Shape of slits changed
2 100
35
22
xxi
Terminal Block Configuration
E5GN Models with Screw Terminal Blocks Models with Screw Terminal Blocks
Terminals 1 to 6: M2.6 screw terminals Terminals 1 to 12: M3 screw terminals
Terminals 7 to 9: M2 screw terminals

Terminals 1 to 12: None
xxii
Wire Connections
E5GN Wire connection direction: Perpendicular to Models with Screw Terminal Blocks
back surface Wire connection direction: Horizontal from the top
and bottom of back surface

Wire connection direction: Perpendicular to back
surface
xxiii
Wiring Terminals
E5GN Models with Screw Terminal Blocks Models with Screw Terminal Blocks
Changed from ferrules to crimp terminals for M3
Terminals Wire gauge Ferrules screws.
Tightening torque: 0.5 Nm
Terminals 1 to 6 AWG24 to 2.1 mm dia.
AWG14 max.
5.8 mm max.
Terminals 7 to 9 AWG28 to 1.3 mm dia.
AWG22 max. 5.8 mm max.

Wires: Changed to 10 mm from 5 to 6 mm.
5 to 6 mm 5 to 6 mm Ferrules: Changed to 8 to 12 mm from 5 to 6 mm.
0.8 to 1.4 mm
Wires Ferrules
Terminals Screws Tightening

torque
Terminals 1 to 6 M2.6 0.23 to 0.25 Nm

10 mm 8 to 12 mm
Terminals 7 to 9 M2 0.12 to 0.14 Nm
Wires Ferrules
Removing the Terminal Block

E5GN Press firmly in on both sides of the terminal block to Insert a tool into the tool holes (one on the top and
release the lock and then pull up on the terminal one on the bottom) to release the hooks and pull out
block. the terminal block.
Terminal hole
Note The method for removing the terminal

block is the same for both screw termi-
nal blocks and screwless clamp terminal
blocks.
xxiv
Ratings
Input sensor types for ther- --- The following types of thermocouple input
mocouple inputs were added: W and PLII.
Input range for E thermocouple: 0 to 600C Input range increased for E thermocouple:
200 to 600C
Input accuracy Thermocouple: (0.5% PV or 1C, which- Thermocouple: (0.3% PV or 1C, which-
(There are no changes in ever is greater) 1 digit ever is greater) 1 digit
thermocouple specifications Platinum resistance thermometer: Platinum resistance thermometer: (0.2%
for E5CN-U.) (0.5%PV or 1C, whichever is greater) PV or 0.8C, whichever is greater)
1 digit 1 digit
Analog input: 0.5% FS 1 digit Analog input: 0.2% FS 1 digit
Influence of signal source Thermocouple: 0.1C/ (except B, R, S), Thermocouple: 0.1C/ (for all specifica-
resistance 0.2C/ (B, R, S) tions)
Platinum resistance thermometer: 0.4C/ Platinum resistance thermometer: 0.1C/
Current outputs Current output resolution: Approx. 2,700 Current output resolution: Approx. 10,000
Auxiliary outputs E5CN/E5CN-U/E5GN E5CN/E5CN-U E5GN
(alarm outputs) 250 VAC, 1 A 250 VAC, 3 A 250 VAC, 2 A
Input sampling cycle E5GN E5GN
500 ms 250 ms
Characteristics
Model numbers for the E5CN Models with 24-VAC/VDC power supply A D was added to the model numbers for
specifications models with 24-VAC/VDC power supply
Example: E5CN-R2MT-500 (24 VAC/VDC) specifications.
Example: E5CN-R2MTD-500 (24 VAC/VDC)
Model numbers for the Example: E5AN-R3MT-500 (100 to 240 -N was added to all model numbers
E5AN/EN VAC) A D was added to the model numbers for
Example: E5AN-R3MT-500 (24 VAC/VDC) models with 24-VAC/VDC power supply
specifications.
Example:
E5AN-R3MT-500-N (100 to 240 VAC)
E5AN-R3MTD-500-N (24 VAC/VDC)
Model numbers for the Examples: E5GN-RTC (100 to 240 VAC) Model numbers have changed accompa-
E5GN E5GN-RP (100 to 240 VAC) nying the introduction of universal input
24-VAC/DC Specification capability.
Example: E5GN-RTC (24 VAC/DC) A D was added to the model numbers for
models with 24-VAC/VDC power supply
specifications.
Example: E5GN-RT (100 to 240 VAC)
E5GN-RTD (24 VAC/VDC)
Front panel --- PV status display and SV status display
PF Key added (E5AN/EN only).
--- PV/SP display selection for three-level dis-

play (E5AN/EN only) *
xxv
Inputs --- Square root extraction (for models with ana-
log inputs)
Outputs --- Control output ON/OFF count alarm
--- MV change rate limiter
Controls --- 40% AT
--- Automatic cooling coefficient adjustment for
heating/cooling control
Alarms --- PV rate of change alarm
--- OC alarm (only for models with heater burn-
out detection)
Other --- Logic operations
--- Inverting direct/reverse operation using
event inputs or communications commands
* A 2-level display is set when shipped from the factory.

xxvi
Communications Characteristics
Communications Double word access only Word access and double word access
access size
CompoWay/F services --- Composite Read from Variable Area and Com-
posite Write to Variable Area
Communications buffer 40 bytes 217 bytes
size
Baud rate 38.4 kbps max. E5GN: 19.2k max. 57.6 kbps max.
Setup Tool Cable Communications: 38.4k (fixed)
External communica- RS-485/RS-232C external communications RS-485/RS-232C external communications and
tions and Setup Tool communications cannot be Setup Tool communications can be used at the
used at the same time. same time.
Other Upgrades
Mounting Bracket
(E5AN/EN only)
Modified section
Mounting Bracket for upgraded models

Mounting Bracket for previous models
Note The Mounting Bracket for the previous
models cannot be used for upgraded
models.
Packing case Previous ID code: N5 New ID code: N6
(E5AN/EN only)
TYPEE5AN-R3MT-500
TYPE E5CN T TYPEE5AN-R3MT-500-N
TYPE E5CN- R2T
TEMPERATURE CONTROLLER TEMPERATURE CONTROLLER
TEMP.
TEMP. TEMP.
TEMP.
MULTI-RANGE
MULTI
- RANGE MULTI-RANGE
MULT-IRANGE
VOLTS
VOLTS VOLTS
VOLTS
100-240
100- 240 VAC
VAC 100-240
100- 240VAC
VAC
LOT No.
N5 LOT
N5 No.**** QYT.1
QYT.1 N6 LOT No.
N6 LOT No.**** QYT.1
QYT.1
OMRON Corporation MADE IN CHINA OMRON

OMRONCorporation
CorporationMADE
MADEIN CHINA
IN CHIN
Terminal Cover (sold E53-COV10 (for E5CN only) E53-COV17 (for E5CN only)
separately) for E5CN
Note The Terminal Cover for the previous
models cannot be used for improved
models.
xxvii
Terminal Cover (sold E53-COV11 E53-COV16
separately) for E5AN/EN
Note The Terminal Cover for the previous
models cannot be used for improved
models.
Front Panel Labels

(E5GN)
The design has been changed.

Display area dimensions: 36.1 9.8 mm Added characters: MANU, SUB1, SUB2, and
(W H) HA
Display area dimensions: 36.8 10.1 mm (W
H)
xxviii
Body Labels (E5GN) 1. Body labels: 3 1. Body labels: All labels combined into one la-
2. Model number: Refer to the model num- bel.
ber legend. 2. Model number: Refer to the model number
3. Lot No.: Year of manufacture (last digit of legend.
year 3. Lot No.: Year of manufacture (last two digits
@@@@@@ of year)
@@@@@@@
1, 2: Manufacture day: 01 to 31
3: Manufacture month: 1 to 9, X, Y, and Z 1, 2: Manufacture day: 01 to 31
(January to December) 3: Manufacture month: 1 to 9, X, Y, and Z (Janu-
4: Last digit of year. ary to December)
5, 6: Manufacturing factory code 4, 5: Year of manufacture (last two digits of year)
6, 7: Manufacturing factory code
Top of Controller Bottom of Controller

Top of Controller
Box Labels (E5GN) No ID number N6 has been added to identify the new mod-
els.
RTC RT
Ro Ro
xxix
Conventions Used in This Manual
Model Notation
The E5CN-@@@, E5CN-@@@U, E5AN-@@@, E5EN-@@@, and E5GN-@@@ are given as the E5CN,
E5CN-U, E5AN, E5EN, and E5GN when they share functionality.
The following notation is used when specifying differences in functionality.
Notation Options
E5@N-@@@B Two event inputs
E5@N-@@@03 RS-485 communications
E5@N-@@H One of HB, HS, and heater overcurrent detection
E5@N-@@HH Two of HB, HS, and heater overcurrent detection (See note 1.)
E5@N-@Q Control output 2 (voltage output) (See note 1.)
E5@N-@@P External power supply to ES1B (See note 1.)
E5@N-@@@01 RS-232C communications (See note 2.)
E5@N-@@F Transfer output (See note 3.)
Note: (1) Excluding the E5GN.

(2) Excluding the E5CN.
(3) The E5AN and E5EN only.
Meanings of Abbreviations
The following abbreviations are used in parameter names, figures and in text explanations. These
abbreviations mean the following:
Symbol Term
PV Process value
SP Set point
SV Set value
AT Auto-tuning
ST Self-tuning
HB Heater burnout
HS Heater short (See note 1.)
OC Heater overcurrent
LBA Loop burnout alarm
EU Engineering unit (See note 2.)
Note: (1) A heater short indicates that the heater remains ON even when the control output from the Tempera-
ture Controller is OFF because the SSR has failed or for any other reason.
(2) EU stands for Engineering Unit. EU is used as the minimum unit for engineering units such as C,
m, and g. The size of EU varies according to the input type.
For example, when the input temperature setting range is 200 to +1300C, 1 EU is 1C, and when
the input temperature setting range is 20.0 to +500.0C, 1 EU is 0.1C.
For analog inputs, the size of EU varies according to the decimal point position of the scaling setting,
and 1 EU becomes the minimum scaling unit.
xxx
How to Read Display Symbols
The following tables show the correspondence between the symbols displayed on the displays and
alphabet characters. The default is for 11-segment displays.
a b c d e f g h i j k l m
A B C D E F G H I J K L M
n o p q r s t u v w x y z
N O P Q R S T U V W X Y Z
The Character Select parameter in the advanced function setting level can be turned OFF to display
the following 7-segment characters. (Refer to page 243.)
A B C D E F G H I J K L M
N O P Q R S T U V W X Y Z
xxxi
xxxii
TABLE OF CONTENTS
SECTION 1
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1-1 Names of Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
1-2 I/O Configuration and Main Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
1-3 Setting Level Configuration and Key Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
1-4 Communications Function. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
1-5 Insulation Block Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
SECTION 2
Preparations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
2-1 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
2-2 Wiring Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
2-3 Using the Support Software Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
SECTION 3
Basic Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
3-1 Initial Setting Examples. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
3-2 Setting the Input Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
3-3 Selecting the Temperature Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
3-4 Selecting PID Control or ON/OFF Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
3-5 Setting Output Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
3-6 Setting the Set Point (SP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
3-7 Using ON/OFF Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
3-8 Determining PID Constants (AT, ST, Manual Setup) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
3-9 Alarm Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
3-10 Using Heater Burnout, Heater Short, and Heater Overcurrent Alarms . . . . . . . . . . . . . . . . . 73
3-11 Setting the No. 3 Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
SECTION 4
Applications Operations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
4-1 Shifting Input Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
4-2 Alarm Hysteresis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
4-3 Setting Scaling Upper and Lower Limits for Analog Inputs . . . . . . . . . . . . . . . . . . . . . . . . . 94
4-4 Executing Heating/Cooling Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
4-5 Using Event Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
4-6 Setting the SP Upper and Lower Limit Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
4-7 Using the SP Ramp Function to Limit the SP Change Rate . . . . . . . . . . . . . . . . . . . . . . . . . 106
4-8 Moving to the Advanced Function Setting Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
4-9 Using the Key Protect Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
4-10 PV Change Color. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
4-11 Alarm Delays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116
4-12 Loop Burnout Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
4-13 Performing Manual Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122
4-14 Using the Transfer Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126
xxxiii
TABLE OF CONTENTS
4-15 Using the Simple Program Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129
4-16 Output Adjustment Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136
4-17 Using the Extraction of Square Root Parameter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137
4-18 Setting the Width of MV Variation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139
4-19 Setting the PF Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141
4-20 Counting Control Output ON/OFF Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143
4-21 Displaying PV/SV Status. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145
4-22 Logic Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147
SECTION 5
Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157
5-1 Conventions Used in this Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 158
5-2 Protect Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159
5-3 Operation Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163
5-4 Adjustment Level. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 177
5-5 Monitor/Setting Item Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 196
5-6 Manual Control Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 197
5-7 Initial Setting Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 199
5-8 Advanced Function Setting Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 218
5-9 Communications Setting Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 255
SECTION 6
CALIBRATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 257
6-1 Parameter Structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 258
6-2 User Calibration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260
6-3 Thermocouple Calibration (Thermocouple/Resistance Thermometer Input) . . . . . . . . . . . . 260
6-4 Platinum Resistance Thermometer Calibration
(Thermocouple/Resistance Thermometer Input). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 264
6-5 Analog Input Calibration (Thermocouple/Resistance Thermometer Input) . . . . . . . . . . . . . 265
6-6 Calibrating Analog Input (Analog Input) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 267
6-7 Checking Indication Accuracy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 270
Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 275
Index. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 309
Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 317
xxxiv
About this Manual:
This manual describes the E5CN/CN-U/AN/EN Digital Temperature Controllers and includes the sec-
tions described below.
Please read this manual carefully and be sure you understand the information provided before
attempting to set up or operate an E5CN/CN-U/AN/EN Digital Temperature Controller.
Overview
Section 1 introduces the features, components, and main specifications of the E5CN/CN-U/AN/EN/
GN Digital Temperature Controllers.
Setup
Section 2 describes the work required to prepare the E5CN/CN-U/AN/EN/GN Digital Temperature
Controllers for operation, including installation and wiring.
Basic Operations
Section 3 describes the basic operation of the E5CN/CN-U/AN/EN/GN Digital Temperature Control-
lers, including key operations to set parameters and descriptions of display elements based on specific
control examples.
Section 5 describes the individual parameters used to setup, control, and monitor operation.
Operations for Applications

Section 4 describes scaling, the SP ramp function, and other special functions that can be used to
make the most of the functionality of the E5CN/CN-U/AN/EN/GN Digital Temperature Controllers.
Section 5 describes the individual parameters used to setup, control, and monitor operation.
User Calibration
Section 6 describes how the user can calibrate the E5CN/CN-U/AN/EN/GN Digital Temperature Con-
trollers.
Appendix
The Appendix provides information for easy reference, including lists of parameters and settings.
!WARNING Failure to read and understand the information provided in this manual may result in per-
sonal injury or death, damage to the product, or product failure. Please read each section
in its entirety and be sure you understand the information provided in the section and
related sections before attempting any of the procedures or operations given.
xxxv
xxxvi
SECTION 1
Introduction
This section introduces the features, components, and main specifications of the E5CN, and E5AN, and E5EN Digital
Temperature Controllers.
1-1 Names of Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

1-1-1 Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
1-1-2 Explanation of Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1-1-3 Using the Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1-2 I/O Configuration and Main Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
1-2-1 I/O Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
1-2-2 Main Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
1-3 Setting Level Configuration and Key Operations . . . . . . . . . . . . . . . . . . . . . . 15
1-3-1 Selecting Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
1-3-2 Saving Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
1-4 Communications Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
1-5 Insulation Block Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
1
Names of Parts Section 1-1
1-1 Names of Parts

1-1-1 Front Panel
E5CN/CN-U The front panel is the same for the E5CN and E5CN-U.
Temperature unit
No. 1 display
Operation indicators
No. 2 display
Up Key
Level Key
Mode Key Down Key
E5AN
Temperature unit
SUB1
SUB2
PV
SUB3 No.1 display
Operation indicators HA
SV
No. 2 display
OUT1 STOP MV No. 3 display

OUT2 CMW MANU
Function Key/
Auto/Manual Key
PF Up Key
A/M
E5AN Down Key
Level Key Mode Key
2
E5EN
Operation indicators
SUB1 SUB2
HA SUB3
PV
Temperature unit
No.1 display
SV
No.2 display
OUT1 STOP MV
Operation indicators OUT2 CMW MANU
No.3 display
Up Key
Mode Key
Level Key PF Function Key/

A/M
Auto/Manual Key
E5EN
Down Key
E5GN
No. 1 display
Temperature Operation
unit indicators
Operation
indicators
No. 2 display
Level Key
Mode Key Down Key Up Key
3
1-1-2 Explanation of Indicators

No. 1 Display Displays the process value or parameter name.
Lights for approximately one second during startup.
No. 2 Display Displays the set point, parameter operation read value, or the variable input
value.
The set point will flash during autotuning.
No. 3 Display Displays MV, soak time remaining, or multi SP.
(E5AN/EN Only)
A 2-level display is set when shipped from the factory.
Operation Indicators
1,2,3... 1. SUB1 (Sub 1)
Lights when the function set for the Auxiliary Output 1 Assignment param-
eter is ON.
SUB2 (Sub 2)
eter is ON.
SUB3 (Sub 3) (E5AN/EN Only)
eter is ON.
2. HA (Heater Burnout, Heater Short Alarm, Heater Overcurrent Detection
Output Display)
Lights when a heater burnout, heater short alarm, or heater overcurrent
occurs.
3. OUT1 (Control Output 1)
Lights when the control output function assigned to control output 1 turns
ON. For a current output, however, OFF for a 0% output only.
OUT2 (Control Output 2) (Excluding the E5GN)
Lights when the control output function assigned to control output 2 turns
ON. For a current output, however, OFF for a 0% output only.
4. STOP
Lights when operation is stopped.
During operation, this indicator lights when operation is stopped by an
event or by key input using the RUN/STOP function.
5. CMW (Communications Writing)
Lights when communications writing is enabled and is not lit when it is dis-
abled.
6. MANU (Manual Mode)
Lights when the auto/manual mode is set to manual mode.
7. (Key)
Lights when settings change protect is ON (i.e., when the U and D Keys
are disabled by protected status.)
Temperature Unit The temperature unit is displayed when parameters are set to display a tem-
perature. The display is determined by the currently set value of the Tempera-
ture Unit parameter. c indicates C and f indicates F.
This indicator flashes during ST operation. It is OFF on models with linear
inputs.
4
1-1-3 Using the Keys

This section describes the basic functions of the front panel keys.
PF (Function (Auto/ This is a function key. When it is pressed for at least 1 second, the function set
Manual)) Key in the PF Setting parameter will operate.
(E5AN/EN Only)
Example: When A-M (auto/manual) is selected in the PF Setting parameter
(initial value: A-M), the key operates as an auto/manual switch, switching
between Auto Mode and Manual Mode. If the key is pressed for more than 1
second (regardless of key release timing), the mode will switch.
O Key Press this key to move between setting levels. The setting level is selected in
the following order: operation level: adjustment level, initial setting level, com-
munications setting level.
M Key Press this key to change parameters within a setting level.
The parameters can be reversed by holding down the key (moving one per
second in reverse order).
U Key Each press of this key increments the value displayed on the No. 2 display or
advances the setting. Holding the key down speeds up the incrementation.
D Key Each press of this key decrements values displayed on the No. 2 display or
reverses the setting. Holding the key down speeds up the incrementation.
O + M Keys Press these keys to change to the protect level. For details on operations
involving holding these keys down simultaneously, refer to 1-3 Setting Level
Configuration and Key Operations. For details on the protect level, refer to
SECTION 5 Parameters.
O + U Keys To restrict set value changes (in order to prevent accidental or incorrect oper-
O + D Keys ations), these key operations require simultaneously pressing the O key
along with U or D key. This applies only to the parameter for the password to
move to protect level. (Refer to page 162.)
5
I/O Configuration and Main Functions Section 1-2
1-2 I/O Configuration and Main Functions

1-2-1 I/O Configuration
E5CN
Control Control output
Temperature input section Control output 1
or analog input (heating)
Control output
(cooling) Control output 2 (See note.)
Heating/cooling
External power
(See note.)
supply for ES1B
Alarm 3
CT1 input
Alarm 2 Auxiliary output 2
Alarm 1
CT2 input
HB alarm
HS alarm Auxiliary output 1

Event inputs
2 channels
OC alarm
Input error
Program end
output Note:
Press one of these keys,
Communications
depending on the model.
function
Note Functions can be assigned individually for each output by changing the set
values for the Control Output 1 Assignment, the Control Output 2 Assignment,
the Auxiliary Output 1 Assignment, and the Auxiliary Output 2 Assignment
parameters in the advanced function setting level.
6
E5CN-U
Control Control output

Temperature input section Control output 1
or analog input (heating)
Control output
(cooling) Heating/
cooling
Standard
Alarm 2
Alarm 1
Auxiliary output 1
Input error
Program end
output
values for the Control Output 1 Assignment, the Auxiliary Output 1 Assign-
ment, and the Auxiliary Output 2 Assignment parameters in the advanced
function setting level.
7
Model Number Structure

Model Number Legend
Controllers Option Units
E5CN-@@M@@-@-500 E53-CN@@@
1 2 3 4 5 6 7 1 2 3 4
1. Control Output 1 1. Applicable Controller

R: Relay output CN: E5CN or E5CN-H
Q: Voltage output (for driving SSR) 2. Function 1
C: Current output Blank: None
Y: Long-life relay output (hybrid) *1 Q: Control output 2 (voltage for driv-
2. Auxiliary Outputs *2 ing SSR)
Blank: None P: Power supply for sensor
2: Two outputs 3. Function 2
3. Option Blank: None
M: Option Unit can be mounted. H: Heater burnout/SSR failure/Heater
4. Input Type overcurrent detection (CT1)
T: Universal thermocouple/platinum HH: Heater burnout/SSR failure/
resistance thermometer Heater overcurrent detection
L: Analog current/voltage input (CT2)
5. Power Supply Voltage B: Two event inputs
Blank: 100 to 240 VAC 03: RS-485 communications
D: 24 VAC/VDC H03: Heater burnout/SSR failure/
6. Case Color Heater overcurrent detection
Blank: Black (CT1) + RS-485 communica-
W: Silver tions
7. Terminal Cover HB: Heater burnout/SSR failure/
-500: With terminal cover Heater overcurrent detection
(CT1) + Two event inputs
HH03: Heater burnout/SSR failure/
Heater overcurrent detection
(CT2) + RS-485 communications
4. Version
N2: Applicable only to models
released after January 2008
E5CN-@@@U
1 2 3 4
1. Output Type
R: Relay output
Q: Voltage output (for driving SSR)
C: Current output
2. Number of Alarms
Blank: No alarm
1: One alarm
2: Two alarms
3. Input Type
T: Universal thermocouple/platinum
resistance thermometer
L: Analog Input
4. Plug-in type
U: Plug-in type
Note Not all combinations of function 1 and function 2 specifications are possible
for Option Units (E53-@@@@).
*1 Always connect an AC load to a long-life relay output. The output will not
turn OFF if a DC load is connected because a triac is used for switching
the circuit. For details, check the conditions in Ratings.
*2 Auxiliary outputs are contact outputs that can be used to output alarms
or results of logic operations.
8
E5AN/EN
Temperature input Control Control output

or analog input Control output 1
section (heating)
Control output
(cooling) Control output 2
Heating/cooling (See note.)
External power
supply for ES1B (See note.)
Alarm 3 Alarm output 3

CT1 input
Alarm 2
Alarm output 2
Alarm 1
CT2 input
HB alarm
HS alarm Alarm output 1

Event inputs 1 and
2 (2 channels)
OC alarm
Input error
Program end
output Note:
Press one of these keys,
Communications depending on the model.
function
Note Functions can be assigned individually to each output by changing the set val-
ues for the Control Output 1 Assignment, Control Output 2 Assignment, Auxil-
iary Output 1 Assignment, Auxiliary Output 2 Assignment, and Auxiliary
Output 3 Assignment parameters in the advanced function setting level.
9

Model Number Legends
E5AN/EN-@3@M@@-@-500-N E53-@
1 2 3 4 5 6 7 8 9 1
1. Control Output 1 1. Function

R: Relay output EN01: RS-232C
Q: Voltage output (for driving SSR) communications
C: Current output EN03: RS-485
communications
2. Auxiliary Outputs
AKB: Event input
3: Three outputs
3. Heater Burnout/Heater Short, Control Output 2,
or External Power Supply for ES1B
Blank: None
Q: Control output 2 (voltage output for driving SSR)
Y: Long-life relay output (hybrid)
H: Heater burnout/Heater short/Heater overcurrent
detection (CT1)
HH: Heater burnout/Heater short/Heater overcurrent
detection (CT2)
P: Power supply for sensor
4. Option
M: Option Unit can be mounted.
5. Input Type
T: Universal thermocouple/platinum resistance
thermometer input
L: Analog current/voltage input
6. Power Supply Voltage
Blank: 100 to 240 VAC
D: 24 VAC/VDC
7. Case Color
Blank: Black
W: Silver
8. Terminal Cover
500: With terminal cover
9. Version
N: Available only to models released after January
2008.
10
E5GN
Temperature input Control Control output Control output 1

or analog input section (heating)
Control output
(cooling) Heating/
cooling
Auxiliary output 1
Alarm 1
Standard
CT1 input
HB alarm
HS alarm
OC alarm
Input error
Event inputs
2 channels
Alarm 3
Program end
output
Communications
function
values for the Control Output 1 Assignment, the Auxiliary Output 1 Assign-
ment, and the Auxiliary Output 2 Assignment parameters in the advanced
function setting level.
11

Model Number Legends
Controllers
E5GN-@@@@@-@-@-@
1 2 3 4 5 6 7 8
1. Control Output 1
R: Relay output
Q: Voltage output (for driving SSR)
C: Current output
2. Auxiliary Outputs
Blank: None
1: One outputs
2: Two outputs
3. Option
Blank: None
01: RS-232C communications
03: RS-485 communications
B: Two event inputs
H: Heater burnout/Heater short/Heater overcurrent
detection (CT1)
4. Input Type
T: Universal thermocouple/platinum resistance
thermometer input
L: Analog current/voltage input
5. Power Supply Voltage
Blank: 100 to 240 VAC
D: 24 VAC/VDC
6. Terminal Type
Blank: Models with Screw Terminal Blocks
C: Models with Screwless Clamp Terminal Blocks
7. Case Color
Blank: Black
W: Silver
8. Communications Protocol
Blank: None
FLK: CompoWay/F communications
Note Silver is available by special order only.
1-2-2 Main Functions

This section introduces the main E5CN/CN-U/AN/EN/GN functions. For
details on particular functions and how to use them, refer to SECTION 3 Basic
Operation and following sections.
Input Sensor Types The following input sensors can be connected for temperature input
(i.e., E5_N-@@@@T):
Thermocouple: K, J, T, E, L, U, N, R, S, B, W, PLII
Infrared temperature sensor: ES1B
10 to 70C, 60 to 120C, 115 to 165C,
140 to 260C
Platinum resistance thermometer: Pt100, JPt100
Analog input: 0 to 50 mV
12
Inputs with the following specifications can be connected for analog input
(i.e., E5_N-@@@@L):
Current input: 4 to 20 mA DC, 0 to 20 mA DC
Voltage input: 1 to 5 VDC, 0 to 5 V DC, 0 to 10 V DC
Control Outputs A control output can be a relay, voltage (for driving SSR), or current out-
put, depending on the model.
Long-life relay outputs (see note) use semiconductors for switching when
closing and opening the circuit, thereby reducing chattering and arcing
and improving durability. However, if high levels of noise or surge are
imposed between the output terminals, short-circuit faults may occasion-
ally occur. If the output becomes permanently shorted, there is the danger
of fire due to overheating of the heater. Design safety into the system,
including measures to prevent excessive temperature rise and spreading
of fire. Take countermeasures such as installing a surge absorber. As an
additional safety measure, provide error detection in the control loop.
(Use the Loop Burnout Alarm (LBA) and HS alarm that are provided for
the E5@N.)
Long-life Varistor
relay output
Inductive
1 load
Varistor
2
Select a surge absorber that satisfies the following conditions.

Voltage used Varistor voltage Surge resistance
100 to 120 VAC 240 to 270 V 1,000 A min.
200 to 240 VAC 440 to 470 V
Always connect an AC load to a long-life relay output (see note). The out-
put will not turn OFF if a DC load is connected.
Note Long-life relay outputs are not supported for the E5GN.
Alarms Set the alarm type and alarm value or the alarm value upper and lower
limits.
If necessary, a more comprehensive alarm function can be achieved by
setting a standby sequence, alarm hysteresis, auxiliary output close in
alarm/open in alarm, alarm latch, alarm ON delay, and alarm OFF delay.
If the Input Error Output parameter is set to ON, the output assigned to
alarm 1 function will turn ON when an input error occurs.
Control Adjustment Optimum PID constants can be set easily by performing AT (auto-tuning)
or ST (self-tuning).
Event Inputs With the E53-CN@B@N2 for the E5CN or the E5AN/EN-@M@-500-N with
the E53-AKB for the E5AN/EN, the following functions can be executed
using event inputs: switching set points (multi-SP, 4 points max.), switch-
ing RUN/STOP, switching between automatic and manual operation, start-
ing/resetting the program, inverting direct/reverse operation, 100% AT
execute/cancel, 40% AT execute/cancel, setting change enable/disable,
and canceling the alarm latch.
Heater Burnout, HS Alarm, With the E53-CN@H@N2 or E53-CN@HH@N2 for the E5CN, or the
and Heater Overcurrent E5AN/EN-@@H@-500-N or E5AN/EN-@@HH@-500-N, the heater burnout
detection function, HS alarm function, and heater overcurrent detection
function can be used.
13
Communications Communications functions utilizing CompoWay/F (See note 1.), SYSWAY

Functions (See note 2.), or Modbus (See note 3.) can be used.
RS-485 Interface
Use the E53-CN@03N2 for the E5CN or the E53-EN03 for the E5AN/
EN.
RS-232C Interface
Use the E53-EN01 for the E5AN/EN.
Note (1) CompoWay/F is an integrated general-purpose serial communications

protocol developed by OMRON. It uses commands compliant with the
well-established FINS, together with a consistent frame format on
OMRON Programmable Controllers to facilitate communications be-
tween personal computers and components.
(2) SYSWAY communications do not support alarm 3.
(3) Modbus is a communications control method conforming to the RTU
Mode of Modbus Protocol. Modbus is a registered trademark of
Schneider Electric.
(4) The E5CN and E5CN-U do not support the RS-232C interface.
External Power Supply for The E5AN-@P@-N or E5EN-@P@-N with the E53-CN@P@N2 can be used as
ES1B the power supply for ES1B Infrared Temperature Sensors.
Note The E5GN does not provide a power supply for an ES1B Infrared Tempera-
ture Sensor.
Transfer Output A transfer output for 4 to 20 mA can be used with the E5AN/E5EN-@@F.
For E5@N-C@@ models (models without F in the model number), the cur-
rent output can be used as a simple transfer output.
14
Setting Level Configuration and Key Operations Section 1-3
1-3 Setting Level Configuration and Key Operations

Parameters are divided into groups, each called a level. Each of the set val-
ues (setting items) in these levels is called a parameter. The parameters on
the E5CN/CN-U/AN/EN/GN are divided into the following 9 levels.
When the power is turned ON, all of the display lights for approximately one
second.
Power ON
Start in manual mode.
Start in automatic mode.
Press the O Key or the

PF Key for at least 1 s.
(See note 4.) Press the
Operation Adjustment O+ M
Level Level Press the Keys for at
O+ M least 1 s.
Press the Keys for at
a-m O Key less than 1 s. least 3 s.
(Display c
25
will flash
after 1st 100
PF Key second.)
Press the O Key (See note 5.)
Manual (See for at least 3 s while PF Key Monitor/Setting
a-m is displayed. (See note 5.)
mode note (a-m will flash after Item Level
3.) 1st second.)
(See note 4.)

Press the O Key for at
Press the PF Key least 3 s. (Display will flash
Manual for at least 1 s. (See after 1st second.)
Control Level note 1.)
c
25
Press the 100
O Key for Protect Level
at least 1 s.
Note The time taken to move
to the protect level can
Communica- be adjusted by chang-
Initial Setting
Control stops. tions Setting ing the "Move to pro-
Level
Press the Level tect level time" setting.
O Key for less than 1 s. (Refer to page 228.)
Input password while
Press the O Key amoV is displayed. (Set
for at least 1 s. value 169)
Advanced Function
Setting Level
Input password. Control in progress
Control stopped
(See Not displayed for some models

Calibration Level
note 2.)
Level change
Note (1) You can return to the operation level by executing a software reset.
(2) You cannot move to other levels by operating the keys on the front panel
from the calibration level. You must turn OFF the power supply.
(3) From the manual control level, key operations can be used to move to the
operation level only.
Level Control in progress Control stopped
Protect level Can be set. ---
Operation level Can be set. ---
Adjustment level Can be set. ---
Manual control level Can be set. ---
Monitor/setting item level Can be set. ---
Initial setting level --- Can be set.
15
Level Control in progress Control stopped

Advanced function setting level --- Can be set.
Calibration level --- Can be set.
Communications setting level --- Can be set.
Of these levels, the initial setting level, communications setting level,

advanced function setting level, and calibration level can be used only
when control is stopped. Control outputs are stopped when any of
these four levels is selected.
(4) When the PF Setting is set to A-M in models with a PF Key (E5AN/EN)
(5) When the PF Setting is set to PFDP in models with a PF Key (E5AN/EN)
Protect Level To switch to the protect level from the operation level, the adjustment
level, or the monitor/setting item level, simultaneously hold down the O
and M Keys for at least 3 seconds. (See note.) This level is for preventing
unwanted or accidental modification of parameters. Protected levels will
not be displayed, and so the parameters in that level cannot be modified.
Note The key pressing time can be changed in Move to Protect Level pa-
rameter (advanced function setting level).
Operation Level The operation level is displayed when the power is turned ON. You can
move to the protect level, initial setting level, or adjustment level from this
level.
Normally, select this level during operation. While operation is in progress,
items such as the PV and manipulated variable (MV) can be monitored,
and the set points, alarm values, and alarm upper and lower limits can be
monitored and changed.
Adjustment Level To move to the adjustment level, press the O Key once (for less than 1 s).
This level is for entering set values and offset values for control. In addi-
tion to AT (auto-tuning), communications write enable/disable switching,
hysteresis settings, multi-SP settings, and input offset parameters, it
includes HB alarm, HS alarm, OC alarm, and PID constants. From the
adjustment level, it is possible to move to the top parameter of the initial
setting level, protect level, or operation level.
Monitor/Setting Item Level To switch to the monitor/setting item level, press the PF Key from the
operation level or adjustment level. The contents set for monitor/setting
items 1 to 5 can be displayed. You can move from the monitor/setting item
level to the operation level or initial setting level. (This level is supported
by the E5AN and E5EN only.)
Manual Control Level When the O Key is pressed for at least 3 seconds from the operation
level's auto/manual switching display, the manual control level will be dis-
played. (The MANU indicator will light.)
When the PF Setting is set to A-M (auto/manual) and the PF Key is
pressed for more than one second from the operation level or adjustment
level, the manual control level will be displayed (E5AN and E5EN only.)
This is the level for changing the MV in manual mode.
To return to the operation level, press the O Key for at least one second.
It is also possible to return to the operation level by pressing the PF Key
for more than one second when the PF Setting is set to A-M.
16
Initial Setting Level To move to the initial setting level from the operation level or the adjust-
ment level, press the O Key for at least 3 seconds. The PV display
flashes after one second. This level is for specifying the input type and
selecting the control method, control period, setting direct/reverse opera-
tion, setting the alarm types, etc. You can move to the advanced function
setting level or communications setting level from this level. To return to
the operation level, press the O Key for at least one second. To move to
the communications setting level, press the O Key for less than one sec-
ond.
(When moving from the initial setting level to the operation level, all the
indicators will light.)
Note Pressing the O Key for at least 3 seconds in the operation level's
auto/manual switching display will move to the manual control level,
and not the initial setting level.
Advanced Function To move to the advanced function setting level, set the Initial Setting/Com-
Setting Level munications Protect parameter in the protect level to 0 and then, in the ini-
tial setting level, input the password (169).
From the advanced function setting level, it is possible to move to the cali-
bration level or to the initial setting level.
This level is for setting the automatic display return time and standby
sequence, and it is the level for moving to the user calibration and other
functions.
Communications Setting To move to the communications setting level from the initial setting level,
Level press the O Key once (for less than 1 s). When using the communica-
tions function, set the communications conditions in this level. Communi-
cating with a personal computer (host computer) allows set points to be
read and written, and manipulated variables (MV) to be monitored.
Calibration Level To move to the calibration level, input the password (1201) from the
advanced function setting level. The calibration level is for offsetting error
in the input circuit.
You cannot move to other levels from the calibration level by operating the
keys on the front panel. To cancel this level, turn the power OFF then back
ON again.
1-3-1 Selecting Parameters

Within each level, the parameter is changed in order (or in reverse order)
each time the M Key is pressed. (In the calibration level, however, param-
eters cannot be changed in reverse order.) For details, refer to SECTION
5 Parameters.
17
Communications Function Section 1-4
Moves in order after M key While the M key is being held

is pressed (if key is down, the parameter will move
released within 1 s). each second in reverse order.
Parameter 1
Parameter 2 Parameter 2
After M key has

M been held down
for 2 s.
Parameter 3 Parameter 3
Hold down the M key
After M key during this interval. After M key has
is pressed been held down
for 1 s.
Parameter 4
1-3-2 Saving Settings

If you press the M Key at the final parameter, the display returns to the
top parameter for the current level.
To change parameter settings, specify the setting using the U or D Key,
and either leave the setting for at least two seconds or press the M Key.
This saves the setting.
When another level is selected after a setting has been changed, the con-
tents of the parameter prior to the change is saved.
When you turn the power OFF, you must first save the settings (by press-
ing the M Key). The settings are sometimes not changed by merely
pressing the U or D Keys.
1-4 Communications Function

The E5CN/AN/EN/GN are provided with a communications function that
enables parameters to be checked and set from a host computer. If the com-
munications function is required, use the E53-CN@03N2 with the E5CN, or
the E53-EN03 or E53-EN01 with the E5AN/EN/GN. For details on the com-
munications function, see the separate Communications Manual Basic Type.
Use the following procedure to move to the communications setting level.
1,2,3... 1. Press the O Key for at least three seconds to move from the operation lev-
el to the initial setting level.
2. Press the O Key for less than one second to move from the initial setting
level to the communications setting level.
3. Select the parameters as shown below by pressing the M Key.
4. Press the U or D Key to change the parameter setting.
18
Communications Function Section 1-4
psel Protocol Setting

cwf
M
u-no Communications Unit No.
1
M
Communications Baud Rate
bps
9.6
M
len Communications Data Length
7 (See note.)
M
sbit Communications Stop Bits
2 (See note.)
M
prty Communications Parity
even
M
Send Data Wait Time
sdwt
20
M
Note The Protocol Setting parameter is displayed only when CompoWay/F commu-
nications are being used.
Setting Communications Match the communications specifications of the E5CN/AN/EN/GN and the
Data host computer. If a 1:N connection is being used, ensure that the communica-
tions specifications for all devices in the system (except the communications
Unit No.) are the same.
Parameter name Symbol Setting (monitor) value Selection symbols Default Unit
Protocol Setting psel CompoWay/F (SYSWAY), cwf, mod CompoWay/F None
Modbus (SYSWAY)
Communications u-no 0 to 99 1 None
Unit No.
Communications bps 1.2, 2.4, 4.8, 9.6, 19.2, 1.2, 2.4, 4.8, 9.6, 19.2, 38.4. 9.6 kbps
Baud Rate 38.4, 57.6 57.6
Communications len 7, 8 7 Bits
Data Length
Communications sbit 1, 2 2 Bits
Stop Bits
Communications prty None, Even, Odd none, even, odd Even None
Parity
Send Data Wait sdwe 0 to 99 20 ms
Time
19
Insulation Block Diagrams Section 1-5
1-5 Insulation Block Diagrams

The insulation block diagrams for the E5CN, E5AN, E5EN, and E5GN are pro-
vided in this section.
E5CN
Input, CT input, Q outputs (outputs 1 and 2)

Communications and events
External power supply
Power
C output
supply
R output
Y output
Auxiliary outputs 1 and 2
: Reinforced insulation : Functional insulation
E5CN-U
Input and Q output (output 1)

C output
Power
supply R output
Y output
Auxiliary outputs 1 and 2
E5AN/EN
Input, CT input, and Q output (output 1)

External power supply and Q output (output 2)
C output and transfer output
Power
supply R output
Y output
Auxiliary output 1
Auxiliary output 2
Auxiliary output 3
E5GN
Input, CT input, Q output (output 1)

Power C output
supply
R output
Auxiliary output 1
Auxiliary output 2
20
SECTION 2
Preparations
This section describes the work required to prepare the E5CN, E5AN, and E5EN Digital Temperature Controllers for
operation, including installation and wiring.
2-1 Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
2-1-1 Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
2-1-2 Panel Cutout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
2-1-3 Mounting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
2-1-4 Removing the Temperature Controller from the Case . . . . . . . . . . . 28
2-2 Wiring Terminals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
2-2-1 Terminal Arrangement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
2-2-2 Precautions when Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
2-2-3 Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
2-3 Using the Support Software Port. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
21
Installation Section 2-1
2-1 Installation
2-1-1 Dimensions
Unit: mm
E5CN
6 91
48 48 1.5 78
44.8 44.8
48.8
58
E5CN-U
6 (84.7)
48 48 44.8 44.8
70.5 14.2
58
48
6 79.2
78
2
E5AN
91 91
112
96 96
79.2
E5EN
6 78
48 2 44
PV
SV
96
91
112
MV
22
E5GN
Models with Screw Terminal Blocks
48 2 99 44.8
35
24
35
22
22
48 2 100 44.8
35
24
35
22
22
23
2-1-2 Panel Cutout

Unit: mm
E5CN/CN-U
Individual Mounting Group Mounting
(48 number of Units 2.5) +1.0
0
45+0.6
0
45+0.6
45+0.6
0
0
60 min.
E5AN

92+0.8
0 0
92+0.8
92+0.8
0
0
120 min.
E5EN
0
45+0.6
0
92+0.8
92+0.8
0
0
120 min.
24
E5GN
+1.0
(48 number of units 2.5) 0
22.2 +0.3
0
45 +0.6
40 min.
0
22.2 +0.3
0
Waterproofing is not possible when group mounting several Controllers.
The recommended panel thickness is 1 to 5 mm for the E5CN, E5CN-U,
and E5GN, and 1 to 8 mm for E5AN and E5EN.
Units must not be closely mounted vertically. (Observe the recommended
mounting space limits.)
When group mounting several Controllers, ensure that the surrounding
temperature does not exceed the ambient operating temperature listed in
the specifications.
2-1-3 Mounting
E5CN/CN-U
E53-COV17
Terminal Cover
Adapter
Waterproof packing
Panel
E5CN E5CN-U
For the Wiring Socket for the E5CN-U, order the P2CF-11 or P3GA-11 sepa-
rately.
Mounting to the Panel
1,2,3... 1. For waterproof mounting, waterproof packing must be installed on the

Controller. Waterproofing is not possible when group mounting several
Controllers. Waterproof packing is not necessary when there is no need for
the waterproofing function. There is no waterproof packing included with
the E5CN-U.
2. Insert the E5CN/E5CN-U into the mounting hole in the panel.
3. Push the adapter from the terminals up to the panel, and temporarily fasten
the E5CN/E5CN-U.
4. Tighten the two fastening screws on the adapter. Alternately tighten the
two screws little by little to maintain a balance. Tighten the screws to a
torque of 0.29 to 0.39 Nm.
25
Mounting the Terminal Cover

For the E5CN, make sure that the UP mark is facing up, and then attach the
E53-COV17 Terminal Cover to the holes on the top and bottom of the Temper-
ature Controller.
E5AN/EN
Mounting Mounting
Bracket Panel Bracket
Panel
Terminal Cover
(E53-COV16)
Terminal Cover
Waterproof packing (E53-COV16)
Waterproof packing
E5AN E5EN
Mounting to the Panel

Controllers. Waterproof packing is not necessary when there is no need for
the waterproofing function.
2. Insert the E5AN/E5EN into the square mounting hole in the panel (thick-
ness: 1 to 8 mm). Attach the Mounting Brackets provided with the product
to the mounting grooves on the top and bottom surfaces of the rear case.
3. Use a ratchet to alternately tighten the screws on the top and bottom
Mounting Brackets little by little to maintain balance, until the ratchet turns
freely.
Mounting the Terminal Cover
Slightly bend the E53-COV16 Terminal Cover to attach it to the terminal block
as shown in the following diagram. The Terminal Cover cannot be attached in
the opposite direction.
26
Slightly bend the

E53-COV16
Terminal Cover in
the direction shown
by the arrows to
attach it to the
terminal block.
Enlarged Illustration of Terminal Section
E5GN Mounting to the Panel

Controllers.
Waterproof packing is not necessary when there is no need for the water-
proofing function.
2. Insert the E5GN into the mounting hole in the panel.
3. Push the adapter from the terminals up to the panel, and temporarily fasten
the E5GN.
4. Tighten the two fastening screws on the adapter. Alternately tighten the
two screws little by little to maintain a balance.Tighten the screws to a
torque of 0.29 to 0.39 Nm.
Panel
Adapter
Waterproof packing E5GN
27
2-1-4 Removing the Temperature Controller from the Case

The Temperature Controller can be removed from the case to perform mainte-
nance without removing the terminal leads. This is possible for only the E5CN,
E5AN, and E5EN, and not for the E5CN-U or E5GN. Check the specifications
of the case and Temperature Controller before removing the Temperature
Controller from the case.
E5CN
Tool insertion hole
Flat-blade screwdriver
(Unit: mm)
(1)
(2)
20 min.
(3)
0.4 2.0
(1)
1,2,3... 1. Insert a flat-blade screwdriver into the two tool insertion holes (one on the
top and one on the bottom) to release the hooks.
2. Insert the flat-blade screwdriver in the gap between the front panel and
rear case, and pull out the front panel slightly. Hold the top and bottom of
the front panel and carefully pull it out toward you, without applying unnec-
essary force.
3. When inserting the body of the Temperature Controller into the case, make
sure the PCBs are parallel to each other, make sure that the sealing rubber
is in place, and press the E5CN toward the rear case into position. While
pushing the E5CN into place, push down on the hooks on the top and bot-
tom surfaces of the rear case so that the hooks are securely locked in
place. Be sure that electronic components do not come into contact with
the case.
Make sure the PCBs are

parallel to each other, and
then press the body of the
Temperature Controller
toward the rear case into
position.
Bottom View of the E5CN
28
E5AN/EN
Tool insertion hole
Tool insertion hole
(1)
(1)
(2)
(2)
(3)
(3)
(1)
(1)
E5AN E5EN
(Unit: mm)
0.4 2.0
5.0
1,2,3... 1. Insert a flat-blade screwdriver into the two tool insertion holes (one on the
top and one on the bottom) to release the hooks.
2. Insert the flat-blade screwdriver in the gap between the front panel and
rear case (two on the top and two on the bottom), and use it to pry and pull
out the front panel slightly. Then, pull out on the front panel gripping both
sides. Be sure not to impose excessive force on the panel.
Gap between the Front Panel and Rear Case Gap between the Front Panel and Rear Case
Four gaps, two on the top and two on the bottom Four gaps, two on the top and two on the bottom
Top View of E5AN Top View of E5EN
29
3. When inserting the body of the Temperature Controller into the case, make
sure the PCBs are parallel to each other, make sure that the sealing rubber
is in place, and press the E5AN/EN toward the rear case until it snaps into
position. While pressing the E5AN/EN into place, press down on the hooks
on the top and bottom surfaces of the rear case so that the hooks securely
lock in place. Make sure that electronic components do not come into con-
tact with the case.

toward the rear case until
it snaps into position.
Bottom View of the E5EN

toward the rear case until
it snaps into position.
Bottom View of the E5AN
Removing the Terminal The terminal block can be removed from the E5GN. It is not possible for the
Block E5CN, E5AN, E5EN, and E5CN-U.
E5GN The body of the Controller can be replaced by removing the terminal block
from the E5GN.
1,2,3... 1. Insert a flat-blade screwdriver into the tool holes (one on the top and one
on the bottom) to release the hooks. Do not apply excessive force.
Terminal hole
(Unit: mm)
20 min.
0.4 20
2. Pull the terminal block out while the hooks are released.
Note The method for removing the terminal block is the same for both screw termi-
nal blocks and screwless clamp terminal blocks.
30
Wiring Terminals Section 2-2
Do not connect a different type of terminal block to a Controller. For example,

do not replace a screw terminal block with a screwless clamp terminal block.
The temperature indication accuracy will decrease.
2-2 Wiring Terminals

Confirm the location of the terminals (terminals 1 to 15 for the E5CN, 1 to 30
for the E5AN and E5EN, and terminals 1 to 14 for the E5GN) using the prod-
uct labels and case markings.
2-2-1 Terminal Arrangement

E5CN
Controllers
Control output 1
The E5@N-@@@T@ is set for a K thermocouple
Long-life relay output
(input type of 5) by default. If a difference sensor is
250 VAC, 3 A (resistive load)
used, an input error (s.err) will occur. Check the
Relay output
250 VAC, 3 A (resistive load) setting of the input type parameter.
Voltage output (for driving SSR)
12 VDC, 21 mA
Current output Auxiliary outputs (relay outputs)
0 to 20 mA DC 250 VAC, 3 A
4 to 20 mA DC (resistive load)
Load: 600 max.
Auxiliary outputs
(relay outputs)
+
Control output 1 Auxiliary output 2
Control output 2

Voltage output (for driving SSR) + DO NOT DO NOT A Auxiliary output 1
12 VDC, 21 mA USE USE

mA B
Input power A heater burnout alarm, heater short alarm,
V supply heater overcurrent alarm, or input error is
DO NOT
B
USE + + sent to the output to which the alarm 1
100 to 240 VAC function is assigned.
Analog input TC/Pt
universal input 24 VAC/VDC (no polarity)
Option Units
E53-CNHH03N2 E53-CNHBN2 E53-CNQ03N2 E53-CNPBN2 E53-CNPHN2 E53-CNP03N2
Communications Event inputs Communications Event Inputs and External Power Communications (RS-485)
(RS-485) and CT2 and CT (RS-485) and External Power Supply Supply and CT and External Power Supply
Control Output 2
B(+)
11 11 B(+)
RS-485
B(+)
11
11 External + 11 12 VDC,
11
power supply RS-485
12 12 RS-485 12 20 mA
A() EV1 EV1 12
12 12 A()
13 13
A()
13 DO NOT
EV2 DO NOT DO NOT 13
13 EV2 USE 13 USE
USE
CT2 14 14 + +
CT1 + 14
External 14 12 VDC,
14 External 14
12 VDC,
CT1 power supply power supply
15 Control output 2 20 mA CT1 20 mA
15
15 15
15 15

E53-CNH03N2 E53-CN03N2 E53-CNBN2 E53-CNQHN2 E53-CNQHHN2 E53-CNQBN2

Communications Communications Event inputs Control Output 2 Control Output 2 Event Inputs and
(RS-485) and CT (RS-485) and CT and CT2 Control Output 2
B(+)
11 B(+) + +
11 11 11 11 11
RS-485
RS-485 Control output 2 Control output 2
12
A() 12 12 12 12
EV1
12
DO NOT
A() EV1
13 DO NOT DO NOT 13
USE 13 13 13 13
USE EV2 USE EV2
14 DO NOT 14 DO NOT CT2 14 + 14
14 14
CT1 USE USE CT1 Control output 2
15 CT1
DO NOT DO NOT 15
15 15 15 15
USE USE
Since the voltage output (control output) is not electrically insulated from the internal wiring, one or other of
the control output terminals must be left unearthed when using an earthed thermocouple thermometer. (Con-
nection makes measurements unreliable due to sneak currents.)
To comply with EMC standards, the length of the cable connecting the analog input or universal TC/Pt input
sensor must be 30 m or less. If the cable is longer than 30 m, the EMC standards will not be satisfied.
31
E5CN-U

setting of the input type parameter.
Auxiliary output
250 VAC, 3 A (resistive load)
(Relay outputs)
Control output 1
Relay output Control output 1 Auxiliary output 1
(three terminals used) Auxiliary output 2
SPDT, 250 VAC, 3 A (Control output (cooling side))
(resistive load) DO NOT DO NOT A
USE USE
Voltage output mA An input error is sent to the
(for driving SSR) B sent to which the alarm 1
12 VDC, 21 mA V function is assigned.
Current output DO NOT
4 to 20 mA DC USE Input power supply
B
0 to 20 mA DC
Load: 600 max. Analog input TC/Pt 100 to 240 VAC
universal input 24 VAC/VDC (no polarity)
Note For the Wiring Socket, purchase the P2CF-11 or PG3A-11 separately.
E5AN/EN

Communications
100 to 240 VAC used, an input error (s.err) will occur. Check the E53-EN01 E53-EN03 E53-AKB
24 VAC/VDC (no polarity)
setting of the input type parameter. RS-232C RS-485 Event inputs
11 SD 11 B (+) 11
Control output 1 EV2
Relay output Event Inputs 12 RD 12 12 EV
250 VAC, 5A 1 11 13 SG 13 DO NOT USE 13
CT1/CT2
(resistive load) Input power supply
EV2
Voltage output 2 12
EV1
(for driving SSR)
12 VDC, 40 mA 3 13
Current output Control output 1 CT1/CT2 Control Output 2
External Power Supply
0 to 20 mA DC 4 14 +
4 to 20 mA DC CT1 +
Load: 600 max. Control output 2
5 15 - External power supply
Auxiliary output 3 CT2
-
12 VDC, 20 mA
DO NOT
Control output 2 6 16 USE DO NOT
Voltage output DO NOT USE
(for driving SSR) 7 17 USE
12 VDC, 21 mA Auxiliary output 2
Long-life relay output 8 DO NOT A DO NOT
18
250 VAC, 3 A USE USE
(resistive load) mA
B
9 19
Auxiliary output 1 V DO NOT
10 B A heater burnout alarm, heater short alarm,
20 USE
Auxiliary output heater overcurrent alarm, or input error is
1, 2, 3 TC/Pt universal input Analog input sent to the output to which the alarm 1
Relay outputs function is assigned.
250 VAC, 3 A
(resistive load)
32
E5GN
setting of the input type parameter.
B(+)
Control output 1 DO NOT mA
RS-485 communications DO NOT
+
Relay output USE USE
250 VAC, 2 A SD RD SG Analog input
(resistive load) V
+
RS-232C communications DO NOT
Voltage output USE
(for driving SSR) CT DO NOT
12 VDC, 21 mA CT input USE
Current output A B B
Universal TC/Pt input
0 to 20 mA DC
4 to 20 mA DC Event input EV1 EV2 DO NOT
+
USE
Load: 500 max.
7 8 9 10 11 12
Auxiliary outputs
1 and 2
Relay outputs 1 2 3 4 5 6 13 14
250 VAC, 2 A
(resistive load) Auxiliary
Input power Control Auxiliary output 2
supply + output 1 output 1
100 to 240 VAC A heater burnout alarm, heater short alarm,
24 VAC/VDC (no polarity)
heater overcurrent alarm, or input error is
sent to the output to which the alarm 1
function is assigned.
Auxiliary output 2
connection screws
Auxiliary
output 2
2-2-2 Precautions when Wiring

Separate input leads and power lines in order to prevent external noise.
Use a shielded, AWG24 to AWG14 (cross-sectional area of 0.205 to
2.081 mm2) twisted-pair cable for the E5CN, E5EN, or E5AN. Use a
shielded, AWG24 to AWG18 (cross-sectional area of 0.205 to 0.823 mm2)
twisted-pair cable for the E5GN. The stripping length is 5 to 6 mm for the
E5CN, E5AN, or E5EN, and 6 to 8 mm for the E5GN.
Use crimp terminals when wiring the terminals.
Use the suitable wiring material and crimp tools for crimp terminals.
Tighten the terminal screws to a torque of 0.5 Nm for the E5CN-U and
E5GN and to 0.74 to 0.90 Nm for other models. The terminal torque is
0.5 to 0.6 Nm for auxiliary output 2 on the E5GN.
For the E5CN, E5AN, or E5EN, use the following types of crimp terminals
for M3.5 screws.
33
7.2 mm max.
7.2 mm max.
For the E5GN, use the following types of crimp terminals for M3.0 screws.
5.8 mm max.
5.8 mm max.
For E5GN screwless clamp terminal blocks, use wires with a gauge of
AWG24 to AWG18 (equal to a cross-sectional area of 0.205 to
0.823 mm2). The length of the conductive portion inserted into the termi-
nal must be 10 mm for wires and 8 to 12 mm for ferrules. Ferrules must be
0.8 to 1.4 mm in diameter.
0.8 to 1.4 mm
10 mm
8 to 12 mm
Ferrules wires
Recommended Ferrules for E5GN Screwless Clamp Terminals

Manufacturer Model number
Altech Corp. 2623.0
Daido Solderless Terminal Mfg. Co. AVA-0.5
J.S.T. Mfg. Co. TUB-0.5
Nichifu Co. Single (1 wire) TGNTC-1.25-9T
TGVTC-1.25-11T
TGNTC-1.25-11T
TC0.3-9.5
TC1.25-11S-ST
TC1.25-11S
TC2-11S
Double (2 wires) TGWVTC-1.25-9T
TGWVTC-1.25-11T
Use wires with a gauge of AWG24 to AWG18 (0.205 to 0.823 mm2) for
auxiliary output 2 on the E5GN.
The exposed conductor length inserted into the terminal for wires or fer-
rules must be 6 mm. Ferrules must be 0.8 to 1.5 mm in diameter.
34
0.8 to 1.5 mm
3 mm max.
6 mm 6 mm
Ferrules Wires
Recommended Ferrules for SUB2 on E5GN

Manufacturer Model number
Phoenix Contact AI 0,25-6 BU
AI 0,34-6 TQ
AI 0,5-6 WH
AI 0,75-6 GY
AI 1-6 RD
Note Do not remove the terminal block from the E5AN, E5EN, or E5CN. Doing so
may cause product malfunction or incorrect operation.
2-2-3 Wiring
In the connection diagrams, the left side of the terminal numbers represents
the inside of the Controller and the right side represents the outside.
Power supply With the E5CN, connect to terminals 9 and 10; with the E5CN-U, connect
to pins 10 and 11; with the E5AN, E5EN, and E5GN, connect pins 1 and
2. The following table shows the specifications.
Input power supply E5CN E5CN-U E5AN/EN E5GN
100 to 240 VAC, 50/60 Hz 7.5 VA 6 VA 10 VA 5.5 VA
24 VAC, 50/60 Hz 5 VA 3 VA 5.5 VA 3 VA
24 VDC (no polarity) 3W 2W 4W 2W
These models have reinforced insulation between the input power supply,
the relay outputs, and other terminals.
35
Input Make the connections according to the input type as shown below, using
terminals 3 to 5 for the E5CN, pins 1 to 3 for the E5CN-U, pins 18 to 20 for
the E5AN or E5EN and pins 10 to 12 for the E5GN.
3
Do not
use. 3 3
Do not
use.
+ 3
Do not
3 3 Do not +
use. use.
4 4 4
mA
2 2
mA
2
V v
5 5 5 Do not 1 1 1 Do not
+ + use. + + use.
Platinum resistance Platinum resistance
Thermocouple Analog input Thermocouple Analog input
thermometer thermometer
E5CN E5CN-U
Do not
18
Do not + +
18 use. 18 use. Do not Do not
mA use. use. mA

19 19 19
V
Do not
V Do not
20 20 20
+ + use.
+ + use.
Thermocouple Platinum resistance Thermocouple Platinum resistance

thermometer Analog input thermometer Analog input
E5AN/EN E5GN
When extending the thermocouple lead wires, be sure to use compensating
wires that match the thermocouple type. When extending the lead wires of a
platinum resistance thermometer, be sure to use wires that have low resis-
tance and keep the resistance of the three lead wires the same.
36
Control Output 1 Outputs are sent from terminals 1 and 2 with the E5CN, from pins 4 to 6
with the E5CN-U, and from pins 3 and 4 with the E5AN/EN/GN. The fol-
lowing diagrams show the available outputs and their internal equalizing
circuits.
+v +v
+ +
1 1 1
L L
2 GND 2 2

Relay Voltage (for driving SSR) Current
E5CN
+v +v
+ +
4 4 4
L L
5 GND 5
5

6 6 6

E5CN-U
+v +v
3
+ +
3 3
L L
4 GND 4 4

E5AN/EN
+v +v
+ +
L L

E5GN
The following table shows the specifications for each output type.
E5CN/CN-U
Output type Specifications
Relay 250 VAC, 3 A (resistive load), electrical durability: 100,000
operations
Long-life relay 250 VAC, 3 A (resistive load), electrical durability: 1,000,000
(using a triac) operations
Voltage (for driv- PNP type, 12 VDC 15%, 21 mA (with short-circuit protec-
ing SSR) tion)
Current DC 4 to 20 mA/DC 0 to 20 mA, resistive load: 600 max.
Resolution: Approx. 10,000
37
E5AN/EN
operations
Voltage (for driv- PNP type, 12 VDC +15%, 40 mA (with short-circuit protec-
ing SSR) tion)
E5GN
operations
ing SSR) tion)
Always connect an AC load to a long-life relay output. The output will not
turn OFF if a DC load is connected.
The voltage output (for driving SSR) is not electrically isolated from the
internal circuits. When using a grounding thermocouple, do not connect
any of the control output terminals to the ground. If a control output termi-
nal is connected to the ground, errors will occur in the measured tempera-
ture as a result of leakage current.
Control output 1 (voltage output for driving SSR) and control output 2
(voltage output for driving SSR) are not isolated. For the E5AN/EN, how-
ever, the internal circuits are functionally isolated.
Long-life relay outputs use semiconductors for switching when closing
and opening the circuit, thereby reducing chattering and arcing and
improving durability. However, if high levels of noise or surge are imposed
between the output terminals, short-circuit faults may occasionally occur.
If the output becomes permanently shorted, there is the danger of fire due
to overheating of the heater. Design safety into the system, including
measures to prevent excessive temperature rise and spreading of fire.
Take countermeasures such as installing a surge absorber. As an addi-
tional safety measure, provide error detection in the control loop. (Use the
Loop Burnout Alarm (LBA) and HS alarm that are provided for the E5@N.)
Long-life Varistor
relay output
Inductive
1 load
Varistor
2

100 to 120 VAC 240 to 270 V 1,000 A min.
200 to 240 VAC 440 to 470 V
38
Control Output 2 Outputs are sent from terminals 11, 12, 14, and 15 with the E5CN, and
from pins 14 and 15 with the E5AN/EN. The following diagrams show the
available outputs and their internal equalizing circuits.
+v +v +v
11 14 14 14
L or L L
GND 12 GND 15 15 GND 15
Voltage (for driving SSR) Voltage (for driving SSR) Relay Voltage (for driving SSR)
E5CN E5AN/EN
The following table shows the specifications for each output type.
E5CN
ing SSR) tion)
E5AN/EN
Long-life relay 250 VAC, 3 A (resistive load), electrical durability: 1,000,000
(using a triac) operations
ing SSR) tion)
Always connect an AC load to a long-life relay output. The output will not
turn OFF if a DC load is connected.
The voltage output (for driving SSR) is not electrically isolated from the
internal circuits. Therefore, when using a grounding thermocouple, do not
connect any of the control output terminals to the ground. If a control out-
put terminal is connected to the ground, errors will occur in the measured
temperature as a result of leakage current. With E5AN/EN, however, con-
trol output 2 (voltage output for driving SSR) is functionally isolated from
the internal circuits.
Control output 2 of the E5CN is a voltage output (for driving SSR) only,
and outputs across terminals 11(+) and 12(), or 14(+) and 15().
Control output 1 (voltage output for driving SSR) and control output 2
(voltage output for driving SSR) are not isolated.
Long-life relay outputs use semiconductors for switching when closing
and opening the circuit, thereby reducing chattering and arcing and
improving durability. However, if high levels of noise or surge are imposed
between the output terminals, short-circuit faults may occasionally occur.
If the output becomes permanently shorted, there is the danger of fire due
to overheating of the heater. Design safety into the system, including
measures to prevent excessive temperature rise and spreading of fire.
39
Take countermeasures such as installing a surge absorber. As an addi-

tional safety measure, provide error detection in the control loop. (Use the
Loop Burnout Alarm (LBA) and HS alarm that are provided for the E5@N.)
Long-life Varistor
relay output
Inductive
1 load
Varistor
2

100 to 120 VAC 240 to 270 V 1,000 A min.
200 to 240 VAC 440 to 470 V
Auxiliary Outputs 1, 2, and On the E5CN-@2@@@, auxiliary output 1 (SUB1) is output across termi-
3 nals 7 and 8, and auxiliary output 2 (SUB2) is output across terminals 6
and 8.
On the E5CN-@1@@@U, auxiliary output 1 (SUB1) is output across termi-
nals 7 and 8.
On the E5CN-@2@@@U, auxiliary output 1 (SUB1) is output across termi-
nals 7 and 8, and auxiliary output 2 (SUB2) is output across terminals 7
and 9.
On the E5AN/EN-@3@@@, auxiliary output 1 (SUB1) is output across ter-
minals 9 and 10, auxiliary output 2 (SUB2) is output across terminals 7
and 8, and auxiliary output 3 (SUB3) is output across terminals 5 and 6.
On the E5GN-@2@@@, auxiliary output 1 (SUB1) is output across termi-
nals 5 and 6, and auxiliary output 2 (SUB2) is output across terminals 13
and 14 on the bottom of the Controller. Wire terminals 13 and 14 and
tighten the screws.
When the Input Error Output parameter is set to ON, the output assigned
to the alarm 1 function turns ON when an input error occurs.
When the HB alarm, HS alarm, or heater overcurrent alarm is used with
the E5CN-@@H@, E5CN-@@HH@, or E5GN-@@H@, alarms are output to
the output assigned to the alarm 1 function.
When the HB alarm, HS alarm, or heater overcurrent alarm is used with
the E5AN/EN-@@H@@, alarms are output to the output assigned to the
alarm 1 function.
On the E5CN and E5CN-U, when heating/cooling control is used, auxil-
iary output 2 becomes control output (cooling).
On the E5AN and E5EN, when heating/cooling control is used, auxiliary
output 3 becomes control output (cooling).
On the E5GN, when heating/cooling control is used, auxiliary output 1
becomes control output (cooling).
For models that have a heater burnout alarm, an OR of the alarm 1 func-
tion and the HB alarm, HS alarm, or heater overcurrent alarm is sent to
the output assigned to the alarm 1 function (auxiliary output 1). If the
alarm 1 function is to be used for HB alarm only, set the alarm 1 type to 0
(i.e., do not use alarm 1 function).
The following diagrams show the internal equalizing circuits for auxiliary
outputs 1, 2, and 3.
40
SUB2 SUB1
SUB1 SUB2
E5CN E5CN-U
SUB3 SUB1
SUB2
SUB2
SUB1
Terminal 14 is on
the bottom.
E5AN/EN E5GN
ALM1, 2, 3 can be output to auxiliary output 1, 2, 3, or changed with the

advanced function setting level.
The relay specifications are as follows:
E5CN/AN/EN SPST-NO, 250 VAC, 3 A
E5GN SPST-NO, 250 VAC, 2 A
Event Inputs The E5@N-@@@B supports event inputs. When event inputs 1/2 are to be
used, connect to terminals 11 to 13 or terminals 7 to 9. When event inputs
3/4 are to be used, connect to terminals 23 to 25.
11 11 EV1
12 EV1 12 EV2
EV1
13 EV2 13 EV2
E53-CN@B@N2 in the E53-AKB in the E5GN-@@@B

E5CN-@M@-500 E5AN/EN-@M@-500-N
(for E5CN) (for E5AN/EN)
Use event inputs under the following conditions:

The outflow current is approximately 7 mA.
Contact input ON: 1 k max., OFF: 100 k min.
No-contact input ON: Residual voltage 1.5 V max.; OFF: Leakage current
0.1 mA max.
Polarities during no-contact input are as follows:

11 11 +
EV1 EV1 EV1
12 + 12 +
EV2 EV2 EV2
13 + 13
E53-CN@B@N2 in E53-AKB in the E5GN-@@@B

the E5CN-@M@-500 E5AN/EN-@M@-500-N
(for E5CN) (for E5AN/EN)
41
CT Inputs When the HB alarm, HS alarm, or heater overcurrent alarm is to be used

with the E5CN-@M@-500 with an E53-CN@H/HH@N2 Option Unit, con-
nect a current transformer (CT) across terminals 14 and 15 or terminals
13 and 15 (no polarity).
When the HB alarm, HS alarm, or heater overcurrent alarm is to be used
with the E5AN/EN-@@H@-500-N or E5AN/EN-@@HH@-500-N, connect a
current transformer (CT) across terminals 14 and 15 or terminals 15 and
16 (no polarity).
When using the HB alarm, HS alarm, or heater overcurrent alarm with the
E5GN-@@H@, connect the current transformer (CT) across terminals 7
and 8. (no polarity)
13
14 14
14 14 CT2 CT1
CT 15
CT CT1 CT2
15 15 15 16
E53-CN@@H@N2 E53-CN@HH@N2 E5AN/EN-@@H@-500-N E5AN/EN-@@HH@-500-N

(for E5CN)
7
CT
8
E5GN-@@H@
Communications RS-485
When communications are to be used with the E5@N-@@@03, connect
communications cable across terminals 11 and 12, terminals 21 and 22,
or terminals 7 and 8.
11 B(+)
11 B(+)
RS-485 12 A() RS-485
12 A() 13 Do not use.
E5CN-@@@03 E5AN/EN-@@@03
7 B(+)
RS-485
8 A()
E5GN-@@@03
Specify both ends of the transmission path including the host computer as
end nodes (that is, connect terminators to both ends).
The minimum terminal resistance is 54 .
42
Communications Unit Connection Diagram

E5CN
Host computer
RS-485 Shield

+
E5CN (No. 1) E5CN (No. 31)
FG RS-485 RS-485
No. Abbreviation No. Abbreviation
12 A () 12 A ()
A < B: [1] Mark 11 B (+) 11 B (+)
A > B: [0] Space
Terminator (120 , 1/2 W)
E5AN/EN
Host computer
RS-485 Shield

+
E5AN/EN (No. 31)
FG RS-485 RS-485
22 A () 22 A ()
21 B (+) 21 B (+)
12 A () 12 A ()
A < B: [1] Mark 11 B (+) 11 B (+)
A > B: [0] Space
E5GN
Host computer
RS-485
Shield

+
E5GN (No. 1) E5GN (No. 31)
FG RS-485 RS-485
8 A () 8 A ()
7 B (+) 7 B (+)
A < B: [1] Mark
A > B: [0] Space
The RS-485 connection can be either one-to-one or one-to-N. A maxi-

mum of 32 Units (including the host computer) can be connected in one-
to-N systems. The maximum total cable length is 500 m. Use a shielded,
AWG24 to AWG14 (cross-sectional area of 0.205 to 2.081 mm2) twisted-
pair cable for the E5CN, E5EN, or E5AN. Use a shielded, AWG24 to
AWG18 (cross-sectional area of 0.205 to 0.823 mm2) twisted-pair cable
for the E5GN.
Cross-sectional area of
conductor
AWG24: 0.205 mm2
AWG14: 2.081 mm2
43
RS-232C (E5AN/EN/GN Only)

When communications are to be used with the E5AN/E5EN/E5GN-
@@@01@, connect communications cable across terminals 11 to 13 or
terminals 7 to 9.
SD 7
SD
RD RD
RS-232C 8 RS-232C
SG SG
9
E5AN/EN-@@@01@ E5GN-@@@01@
Host computer
E5AN/EN Host computer (DOS/V) E5AN/EN
RS-232C: 25-pin
RS-232C: 9-pin
RS-232C RS-232C
No. No.
SD (TXD) 2 11 SD RD (RXD) 2 11 SD
RD (RXD) 3 12 RD SD (TXD) 3 12 RD
RS (RTS) 4 13 SG ER (DTR) 4 13 SG
CS (CTS) 5 SG 5
DR (DSR) 6 DR (DSR) 6
SG 7 RS (RTS) 7
ER (DTR) 20 CS (CTS) 8
FG 1
Host computer E5GN Host computer (DOS/V) E5GN

RS-232C: 25-pin RS-232C: 9-pin
RS-232C RS-232C
No. No.
SD (TXD) 2 7 SD RD (RXD) 2 7 SD
RD (RXD) 3 8 RD SD (TXD) 3 8 RD
RS (RTS) 4 9 SG ER (DTR) 4 9 SG
CS (CTS) 5 SG 5
DR (DSR) 6 DR (DSR) 6
SG 7 RS (RTS) 7
ER (DTR) 20 CS (CTS) 8
FG 1
A 1:1 connection is used. The maximum cable length is 15 m. To extend

the transmission path, use the OMRON Z3R RS-232C Optical Interface.
Use a shielded, AWG24 to AWG14 (cross-sectional area of 0.205 to
2.081 mm2) twisted-pair cable for the E5CN, E5EN, or E5AN. Use a
shielded, AWG24 to AWG18 (cross-sectional area of 0.205 to 0.823 mm2)
twisted-pair cable for the E5GN.
Cross-sectional area of
conductor
AWG24: 0.205 mm2
AWG14: 2.081 mm2
External Power Supply for Connect terminals 11 and 12 when using the E53-CN@@PH@N2 as the
ES1B external power supply for the ES1B.
44
Using the Support Software Port Section 2-3
Connect terminals 14 and 15 when using the E53-CN@@PBN2 as the

external power supply for the ES1B.
Connect terminals 14 and 15 when using the E5AN/EN-@@P@-N as the
external power supply for the ES1B.
E53-CN@@PH@N2 E53-CN@@PBN2 E5AN/EN-@@P@-N
11 (+) 14 (+) 14 (+)
12 () 15 () 15 ()
The following table provides the specifications of the external power sup-
ply for ES1B.
Output voltage 12 VDC 10%
Output current 20 mA max.
Note Contact your OMRON representative for information on using the

external power supply for ES1B for other applications.
2-3 Using the Support Software Port

Use the communications port for Support Software to connect the personal
computer to the Temperature Controller when using EST2-2C-MV4 CX-
Thermo or a version of CX-Thermo higher than 4.00, or other Support Soft-
ware. The E5GN is supported from CX-Thermo version 4.2. The E58-CIFQ1
USB-Serial Conversion Cable is required to make the connection.
For information concerning the models that can be used with CX-Thermo,
contact your OMRON sales representative.
Procedure Use the following procedure to connect the Temperature Controller to the per-
sonal computer using the USB-Serial Conversion Cable. The USB-Serial
Conversion Cable is used to communicate with the COM port of the personal
computer. To perform communications using USB-Serial Conversion Cable,
set the communications port (COM port) number to be used for the software
to the COM port assigned to the Cable.
1,2,3... 1. Turn ON the power to the Temperature Controller.

Note If the Cable is connected when the power to the Temperature Con-
troller is OFF, power will be supplied from the personal computer
and impose a load on the internal circuits of the Temperature Con-
troller.
2. Connect the Cable.
Connect the personal computers USB port with the Support Software port
on the Temperature Controller using the Cable.
45
Temperature Controller Connection Method

E5CN/CN-U
Personal computer's USB port
Communications port
for Support Software
E58-CIFQ1
Bottom view of E5CN
E5EN E5AN
Communications port Communications port

for Support Software for Support Software
Bottom view of E5AN
Bottom view of E5EN
Setup Tool port

E5GN
Side View of the E5GN
Note Hold the connector when inserting or disconnecting the Cable.

3. Install the driver.
Install the driver to enable the Cable to be used with the personal comput-
er.
Installation
When the Cable is connected with the personal computer, the OS detects
the product as a new device. At this time, install the driver using the instal-
lation wizard. For details on installation methods, refer to the users man-
ual for the E58-CIFQ1 USB-Serial Conversion Cable.
4. Setting Setup Tool Communications Conditions
Set the communications port (COM port) number to be used for the CX-
Thermo Setup Tool to the COM port number assigned to the USB-Serial
Conversion Cable.
Refer to the E58-CIFQ1 USB-Serial Conversion Cable Instruction Manual
46
and Setup Manual for details on how to check the COM port assigned to
the USB-Serial Conversion Cable.
The communications conditions for Setup Tool COM ports are fixed as
shown in the table below. Set the communications conditions for the CX-
Thermo Setup Tool according to the following table.
Parameter Set value
Communications Unit No. 01
Communications baud rate 38.4 (kbps)
Communications data length 7 (bits)
Communications stop bits 2 (bits)
Communications parity Even
47
48
SECTION 3
Basic Operation
This section describes the basic operation of the E5CN, E5AN, and E5EN Digital Temperature Controllers, including key
operations to set parameters and descriptions of display elements based on specific control examples.
3-1 Initial Setting Examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

3-2 Setting the Input Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
3-2-1 Input Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
3-3 Selecting the Temperature Unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
3-3-1 Temperature Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
3-4 Selecting PID Control or ON/OFF Control . . . . . . . . . . . . . . . . . . . . . . . . . . 54
3-5 Setting Output Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
3-5-1 Control Periods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
3-5-2 Direct and Reverse Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
3-5-3 Assigned Output Functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
3-6 Setting the Set Point (SP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
3-6-1 Changing the SP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
3-7 Using ON/OFF Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
3-7-1 ON/OFF Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
3-7-2 Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
3-8 Determining PID Constants (AT, ST, Manual Setup) . . . . . . . . . . . . . . . . . . . 62
3-8-1 AT (Auto-tuning) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
3-8-2 ST (Self-tuning) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
3-8-3 RT (Robust Tuning) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
3-8-4 Manual Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
3-9 Alarm Outputs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
3-9-1 Alarm Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
3-9-2 Alarm Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
3-10 Using Heater Burnout, Heater Short, and Heater Overcurrent Alarms. . . . . . 73
3-10-1 Heater Burnout, Heater Short,
and Heater Overcurrent Alarm Operations. . . . . . . . . . . . . . . . . . . . 73
3-10-2 Installing Current Transformers (CT). . . . . . . . . . . . . . . . . . . . . . . . 74
3-10-3 Calculating Detection Current Values . . . . . . . . . . . . . . . . . . . . . . . 75
3-10-4 Application Examples. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
3-10-5 Settings: HB Alarm. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
3-10-6 Settings: Heater Short Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
3-10-7 Settings: Heater Overcurrent Alarm . . . . . . . . . . . . . . . . . . . . . . . . . 82
3-11 Setting the No. 3 Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
3-11-1 PV/SP Display Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
49
Initial Setting Examples Section 3-1
3-1 Initial Setting Examples

Initial hardware setup, including the sensor input type, alarm types, control
periods, and other settings, is done using parameter displays. The O and M
Keys are used to switch between parameters, and the amount of time that you
press the keys determines which parameter you move to.
This section describes two typical examples.
Explanation of Examples
Changing Parameters
A image means that there are parameters.
in-t Continue pressing the M key to change parameters
0 in-h until you reach the intended parameter.
100 M
M in-l
0 M
Changing Numbers
C
cntl cntl
25 Numeric data and selections in each
onof onof 0
screen can be changed by using the
U and D keys.
Example 1
Input type: 5 (K thermocouple, Setup Procedure

200C to 1,300C) Power ON Power ON
Control method: ON/OFF control
Alarm type: 2 (upper limit) An s.err
Alarm value 1: 20C (deviation) error will be Operation
Set point: 100C displayed if Level C
the power 25 PV/SP

0
supply is
turned ON
before the Press the O key for
Initial Setting sensor is at least 3 s.
Level Control stops.
connected. Initial Setting
Level
Set input Input Type: 5
specifications
Check input type. in-t
5
M
Check that ON/OFF
Set control
specifications control method is cntl control:
onof
ON/OFF control. onof PID pid
M control:
Alarm 1 Type: 2
Set alarm type
Check alarm type.
alt1
2
M
Press the O key for

at least 1 s.
Control starts.
Operation
Level
C
Use the U and
D keys to set the
25 PV/SP: 100
SP to 100C. 100
M
Operation
Confirm that
control is running.
r-s Running run
Level run Stopped: stop
M
Use the U and C
Set alarm values D keys to set the al-1 Alarm Value 1: 20

alarm value to 20
20C.
M
Start operation Start operation.
50
Initial Setting Examples Section 3-1
Example 2
Input type: 9 (T thermocouple,

200C to 400C)
Control method: PID control
PID constants found using auto-
tuning (AT).
Alarm type: 2 upper limit
Alarm value 1: 30C
Set point: 150C
Setup Procedure
Power ON Power ON
Operation Level
C
25 PV/SP
0
Press the O key for

at least 3 s.
Initial Setting Control stops.
Level Initial Setting
Level
Set input
Use the U and
D keys to
in-t Input Type: 9
specifications select the input 9
type.
M
Use the U and
Set control D keys to select cntl ON/OFF
control:
onof For PID, set pid.
specifications PID control. pid pid
PID
M control:
Use the U and To execute on When ON, self-tuning
D keys to set ST st ST: operates.
to OFF. off To cancel off
Set alarm type ST:
M
Check the
control period. cp Control Period
(Heat) 20
It is recommended that 20 seconds
be set for a relay output and 2
20 (Unit: Seconds) seconds for an SSR voltage output.
M
Check the
alarm type. alt1 Alarm 1 Type: 2
2
M
Press the O key for
at least 1 s.
PV/SP
after AT is Control starts.
stopped Operation Level
C
25 Use the U and
D keys to set
C
25
150 PV/SP: 150
the SP to 150C. 150
C
Adjustment 26 Press the O key
Level 150 (for less than 1 s).
Adjustment
The set point Level To execute
flashes during 100%AT: at-2 To execute 100% AT (auto-tuning),
AT execution auto-tuning (AT)
execution.
Execute AT. at To execute
40%AT: at-1
select at-2. To execute 40% AT,
select at-1. To cancel AT, select
off To cancel
After AT is
AT: off off: (AT cancel).
(When PID stopped
control is Press the O key
at (for less than 1 s).
selected) off Operation Level
During AT
C
Confirm that
execution
the set point 25 PV/SP
at is 150C. 150
at-1 M
Operation Confirm that
Level control is r-s Running run
running. run Stopped stop
M
Set alarm value Use the U and C
D keys to set al-1 Alarm 30

the alarm value 30 Value 1
to 30C.
M
Start operation.
Start operation
51
Setting the Input Type Section 3-2
3-2 Setting the Input Type

The Controller supports four input types: platinum resistance thermometer,
thermocouple, infrared temperature sensor, and analog inputs. Set the input
type that matches the sensor that is used. In the product specifications, there
are models with thermocouple/resistance thermometer inputs (universal
inputs) and models with analog input. The settings differ depending on the
model. Check to make sure which model you are using.
3-2-1 Input Type

The following example shows how to set a K thermocouple for 20.0 to
500.0C.
Operating Procedure
Operation Level 1. Press the O Key for at least three seconds to move from the operation
C
level to the initial setting level.
25
0
Initial Setting Level 2. Press the U Key to enter the set value of the desired sensor.
Input Type When you use a K thermocouple (20.0 to 500.0C), enter 6 as the set
in-t value.
5
Hint: The key operation is saved two seconds after the change, or by press-
in-t ing the O or M Key.
6
52
Setting the Input Type Section 3-2
List of Input Types

Input type Specifications Set value Input temperature setting range
Controllers Platinum resistance Pt100 0 200 to 850 (C)/300 to 1,500 (F)
with Ther- thermometer 1 199.9 to 500.0 (C)/199.9 to 900.0 (F)
mocouple/
Resistance 2 0.0 to 100.0 (C)/0.0 to 210.0 (F)
Thermome- JPt100 3 199.9 to 500.0 (C)/199.9 to 900.0 (F)
ter Multi- 4 0.0 to 100.0 (C)/0.0 to 210.0 (F)
input
Thermocouple K 5 200 to 1,300 (C)/300 to 2,300 (F)
6 20.0 to 500.0 (C)/0.0 to 900.0 (F)
J 7 100 to 850 (C)/100 to 1,500 (F)
8 20.0 to 400.0 (C)/0.0 to 750.0 (F)
T 9 200 to 400 (C)/300 to 700 (F)
10 199.9 to 400.0 (C)/199.9 to 700.0 (F)
E 11 200 to 600 (C)/300 to 1,100 (F)
L 12 100 to 850 (C)/100 to 1,500 (F)
U 13 200 to 400 (C)/300 to 700 (F)
14 199.9 to 400.0 (C)/199.9 to 700.0 (F)
N 15 200 to 1,300 (C)/300 to 2,300 (F)
R 16 0 to 1,700 (C)/0 to 3,000 (F)
S 17 0 to 1,700 (C)/0 to 3,000 (F)
B 18 100 to 1,800 (C)/300 to 3,200 (F)
Infrared temperature 10 to 70C 19 0 to 90 (C)/0 to 190 (F)
sensor ES1B 60 to 120C 20 0 to 120 (C)/0 to 240 (F)
115 to 165C 21 0 to 165 (C)/0 to 320 (F)
140 to 260C 22 0 to 260 (C)/0 to 500 (F)
Analog input 0 to 50 mV 23 Either of the following ranges, by scaling:
1,999 to 9,999
199.9 to 999.9
Thermocouple W 24 0 to 2,300 (C)/0 to 3,200 (F)
PLII 25 0 to 1,300 (C)/0 to 2,300 (F)
The default is 5.
If a platinum resistance thermometer is mistakenly connected while a set-
ting for other than a platinum resistance thermometer is in effect, S.ERR
will be displayed. To clear the S.ERR display, check the wiring and then
turn the power OFF and back ON. Make sure that the setting of the input
type parameter agrees with the sensor that is connected.
Input type Specifications Set value Input temperature setting range
Models with Current input 4 to 20 mA 0 Either of the following ranges, by scaling:
analog 0 to 20 mA 1 1,999 to 9,999
input 199.9 to 999.9
Voltage input 1 to 5 V 2 19.99 to 99.99
0 to 5 V 3 1.999 to 9.999
0 to 10 V 4
The default is 0.
53
Selecting the Temperature Unit Section 3-3
3-3 Selecting the Temperature Unit

3-3-1 Temperature Unit
Either C or F can be selected as the temperature unit.
Set the temperature unit in the Temperature Unit parameter of the initial
setting level. The default is c (C).
Operating Procedure The following example shows how to select C as the temperature unit.
C
30
0
Initial Setting Level 2. Select the Temperature Unit parameter by pressing the M Key.
Input Type Press the U or D Key to select either C or F.
in-t c: C
f: F
5
Temperature 3. To return to the operation level, press the O Key for at least one second.
d-u Unit
c
3-4 Selecting PID Control or ON/OFF Control

Two control methods are supported: 2-PID control and ON/OFF control.
Switching between 2-PID control and ON/OFF control is executed by means
of the PID ON/OFF parameter in the initial setting level. When this parameter
is set to pid, 2-PID control is selected, and when set to onof, ON/OFF con-
trol, is selected. The default is onof.
2-PID Control PID control is set by AT (auto-tuning), ST (self-tuning), or manual setting.
For PID control, set the PID constants in the Proportional Band (P), Integral
Time (I), and Derivative Time (D) parameters.
ON/OFF Control In ON/OFF control, the control output is turned ON when the process value is
lower than the current set point, and the control output is turned OFF when
the process value is higher than the current set point (reverse operation).
3-5 Setting Output Specifications

3-5-1 Control Periods
Set the output periods (control periods). Though a shorter period provides
Control Period
cp (Heating) better control performance, it is recommended that the control period be
set to 20 seconds or longer for a relay output to preserve the service life
Control Period
c-cp (Cooling)
of the relay. After the settings have been made in the initial setup, readjust
the control period, as required, by means such as trial operation.
Set the control periods in the Control Period (Heating) and Control Period
(Cooling) parameters in the initial setting level. The default is 20 seconds.
The Control Period (Cooling) parameter is used only for heating/cooling
control.
When control output 1 is used as a current output, Control Period (Heat-
ing) cannot be used.
54
Setting Output Specifications Section 3-5
3-5-2 Direct and Reverse Operation

Direct operation increases the manipulated variable whenever the pro-
cess value increases. Reverse operation decreases the manipulated vari-
able whenever the process value increases.
Manipulated variable Manipulated variable
100% 100%
0% 0%
Low Set Value High Low Set Value High

temperature temperature temperature temperature
Direct operation Reverse operation
For example, when the process value (PV) is lower than the set point (SP)
in a heating control system, the manipulated variable increases according
to the difference between the PV and SP. Accordingly, reverse operation is
used in a heating control system. Direct operation is used in a cooling con-
trol system, in which the operation is the opposite of a heating control sys-
tem. The Control Output 1 Assignment is set to o (control output (heating))
for either direct or reverse operation.
Direct/reverse operation is set in the Direct/Reverse Operation parameter
in the initial setting level. The default is or-r (reverse operation).
Operating Procedure In this example, the input type, temperature unit, direct/reverse operation, and
control period (heat) parameters are checked.
Input type = s (K thermocouple)
Temperature unit = c (C)
Direct/reverse operation = or-r (reverse operation)
Control period (heat) = 20 (seconds)
C
30
0
Initial Setting Level 2. The input type is displayed. When the input type is being set for the first
Input Type time, s (K thermocouple) is set. To select a different sensor, press the U
in-t or D Key.
5
Temperature 3. Select the Temperature Unit parameter by pressing the M Key. The de-
d-u Unit fault is c (C). To select f (F), press the U Key.
c
Control Period 4. Select the Control Period (Heating) parameter by pressing the M Key.
cp (Heating) The default is 20.
20
55
Direct/Reverse 5. Select the Direct/Reverse Operation parameter by pressing the M Key.

orev Operation The default is or-r (reverse operation). To select or-d (direct opera-
tion), press the U Key.
or-r
Operation Level 6. To return to the operation level, press the O Key for at least one second.
C PV/SP
30
0
Move to Ad- 7. Select the Move to Advanced Function Setting Level parameter by press-
amov vanced Function
Setting Level
ing the M Key.
0
3-5-3 Assigned Output Functions

Function assignments can be changed by changing the settings for con-
trol and auxiliary output assignments.
The default function assignments for each output are shown below.
Parameter name Symbol Initial status
Control Output 1 Assignment out1 Control output (heating)
Control Output 2 Assignment out2 Not assigned.
Auxiliary Output 1 Assignment sub1 Alarm 1
(E5AN/EN only)
Refer to pages 240 to 242 for the functions that can be assigned to the
outputs.
Each output is automatically initialized as shown below by changing the
control mode.
Example: E5CN
Parameter name Symbol Without control output 2 With control output 2
Standard Heating/cooling Standard Heating/cooling
Control Output 1 out1 Control output Control output Control output Control output
Assignment (heating) (heating) (heating) (heating)
Control Output 2 out2 Not assigned. Not assigned. Not assigned. Control output
Assignment (See note 1.) (See note 1.) (cooling)
Auxiliary Output 1 sub1 Alarm 1 Alarm 1 Alarm 1 Alarm 1
Assignment (See note 2.) (See note 2.) (See note 2.) (See note 2.)
Auxiliary Output 2 sub2 Alarm 2 Control output Alarm 2 Alarm 2
Assignment (See note 3.) (cooling)
(See note 3.)
Example: E5GN
Parameter name Symbol Standard Heating/cooling
Control Output 1 out1 Control output Control output
Assignment (heating) (heating)
Auxiliary Output 1 sub1 Alarm 1 Control output
Assignment (See note 2.) (cooling)
Auxiliary Output 2 sub2 Alarm 2 Alarm 2
Assignment
56
Note (1) There is no control output 2 and no parameter assignment is displayed

for that output.
(2) The Auxiliary Output 1 Assignment parameter becomes the program end
output unless the Program Pattern parameter is set to OFF.
(3) For the E5AN/EN, the Auxiliary Output 3 Assignment parameter is set as
the control output for cooling. (The Auxiliary Output 2 Assignment param-
eter is set for alarm 2).
Alarms
It will be specified in this section when an alarm must be assigned, i.e., when
an alarm must be set for the Control Output 1 or 2 Assignment parameters, or
for the Auxiliary Output 1 to 3 Assignment parameters. For example, if alarm 1
is set for the Control Output 1 Assignment parameter, then alarm 1 has been
assigned.
Assigning a work bit to either control output 1 or 2 or to auxiliary output 1 to 3
is also considered to be the same as assigning an alarm. For example, if work
bit 1 is set for the Auxiliary Output 1 Assignment parameter, then alarms 1 to 3
have been assigned.
Operating Procedure This procedure sets the following control and auxiliary output assignments.
Control output 1: Control output (heating); Control output 2: Control output
(cooling); Auxiliary output 1: Alarm 1; Auxiliary output 2: Alarm 2
C PV/SP level to the initial setting level.
25
100
Initial Setting Level 2. Select the Standard or Heating/Cooling parameter by pressing the M
Input Type Key.
in-t
5
Initial Setting Level
Standard or
5-hc Heating/Cooling
stnd
Initial Setting Level 3. Press the U Key to set the parameter to h-c.
Note The following output assignments do not need to be set because they
5-hc are set automatically by changing the control mode, but they are
h-c shown here as a reference for checking the assignments for each out-
put.
Setting Level
ing the M Key. (For details on moving between levels, refer to 4-8 Moving
to the Advanced Function Setting Level.)
0
Advanced Function Setting Level 5. Press the D Key to enter the password (169), and move from the initial
Parameter setting level to the advanced function setting level.
init Initialization
off
57
Advanced Function Setting Level 6. Select the Control Output 1 Assignment parameter by pressing the M
Control Output Key.
out1 1 Assignment
o
7. Press the U or D Key to set o.
out1 (The default is o.)
o
Advanced Function Setting Level 8. Select the Control Output 2 Assignment parameter by pressing the M
Control Output Key.
out2 2 Assignment
c-o
9. Press the U or D Key to set c-o.
out2 (When h-c is selected for the Standard or Heating/Cooling parameter,
the setting will be c-o.)
c-o
Advanced Function Setting Level 10. Select the Auxiliary Output 1 Assignment parameter by pressing the M
Auxiliary Output Key.
sub1 1 Assignment
alm1
11. Press the U or D Key to set alm1.
sub1 (The default is alm1.)
alm1
Advanced Function Setting Level 12. Select the Auxiliary Output 2 Assignment parameter by pressing the M
Auxiliary Output Key.
sub2 2 Assignment
alm2
13. Press the U or D Key to set alm2.
sub2 (The default is alm2.)
alm2
Initial Setting Level 14. Press the O Key for at least one second to move from the advanced
Input Type function setting level to the initial setting level.
in-t
5
Operation Level 15. Press the O Key for at least one second to move from the initial setting
C PV/SP level to the operation level.
25
100
Auxiliary Output When close in alarm is set, the status of the auxiliary output is output
Opening or Closing in unchanged. When open in alarm is set, the status of the auxiliary output
Alarm function is reversed before being output.
Each auxiliary output can be set independently.
These settings are made in the Auxiliary Output 1 to 3 Open in Alarm
parameters (advanced function setting level).
The default is n-o: Close in Alarm.
58
Setting the Set Point (SP) Section 3-6
When open in alarm is set for the alarm 1 output, the open in alarm sta-
tus is also applied to heater burnout, HS alarm, heater overcurrent, and
input error outputs.
Auxiliary output Auxiliary Indicators
functions 1 to 3 output (SUB1 to SUB3)
Close in Alarm ON ON Lit
OFF OFF Not lit
Open in Alarm ON OFF Lit
OFF ON Not lit
The alarm output will turn OFF (i.e., the relay contacts will open) when
power is interrupted and for about two seconds after the power is turned
ON regardless of the setting of the Auxiliary Output 1 to 3 Open in Alarm
parameter.
3-6 Setting the Set Point (SP)

Operation Level The operation level is displayed when the power is turned ON. The process
C
value (PV) is at the top of the display, and the set point (SP) is at the bottom.
20
0
Operation Level For Controllers that support a No. 3 display (E5AN/E5EN), the contents set
C
in the PV/SP Display Screen Selection parameter (advanced function setting
20 level) are displayed below the PV and SP.
0 The MV is displayed as the default. For details, refer to 3-11 Setting the No.
50.0 3 Display.
3-6-1 Changing the SP

The set point cannot be changed when the Operation/Adjustment Protect
parameter is set to 3. For details, refer to 4-9 Using the Key Protect Level.
To change the set point, press the U or D Key in the Process Value/Set
Point parameter (in the operation level), and set the desired set value. The
new set point is selected two seconds after you have specified the new
value.
Multi-SP is used to switch between two or four set points. For details, refer
to 4-5 Using Event Inputs for details.
Operating Procedure In this example, the set point is changed from 0C to 200C.
Operation Level 1. Normally, the Process Value/Set Point parameter is displayed. The set
C
point is 0C.
30
0
C 2. Use the U and D Keys to set the set point to 200C.
30
200
59
Using ON/OFF Control Section 3-7
3-7 Using ON/OFF Control

In ON/OFF control, the control output turns OFF when the temperature being
controlled reaches the preset set point. When the manipulated variable turns
OFF, the temperature begins to fall and the control turns ON again. This oper-
ation is repeated over a certain temperature range. At this time, how much the
temperature must fall before control turns ON again is determined by the Hys-
teresis (Heating) parameter. Also, what direction the manipulated variable
must be adjusted in response to an increase or decrease in the process value
is determined by the Direct/Reverse Operation parameter.
3-7-1 ON/OFF Control

Switching between 2-PID control and ON/OFF control is performed using
the PID ON/OFF parameter in the initial setting level. When this parame-
ter is set to pid, 2-PID control is selected, and when it is set to onof, ON/
OFF control is selected. The default is onof.
Hysteresis With ON/OFF control, hysteresis is used to stabilize operation when

switching between ON and OFF. The control output (heating) and control
output (cooling) functions are set in the Hysteresis (Heating) and Hystere-
sis (Cooling) parameters, respectively.
In standard control (heating or cooling control), the setting of the Hystere-
sis (Heating) parameter in the adjustment level is used as the hysteresis
regardless of whether the control type is heating control or cooling con-
trol.
Reverse operation
Hysteresis (heating)
ON
OFF PV
Set point
Three-position In heating/cooling control, a dead band (an area where both control out-
Control puts are 0) can be set to either the heating or cooling side. This makes it
possible to use 3-position control.
Reverse operation
Dead band
Hysteresis (heating) Hysteresis (cooling)
ON
Heating Cooling
side side
OFF PV
Set point
60
Using ON/OFF Control Section 3-7
Parameters
Symbol Parameter: level Application
s-hc Standard or Heating/Cooling: Initial setting level Specifying control method
cntl PID ON/OFF: Initial setting level Specifying control method
orev Direct/Reverse Operation: Initial setting level Specifying control method
c-db Dead Band: Adjustment level Heating/cooling control
hys Hysteresis (Heating): Adjustment level ON/OFF control
chys Hysteresis (Cooling): Adjustment level ON/OFF control
3-7-2 Settings
To execute ON/OFF control, set the Set Point, PID ON/OFF, and Hysteresis
parameters.
Setting the PID ON/OFF Parameter

Operating Procedure Confirm that the PID ON/OFF parameter is set to onof in the initial setting
level.
C PV level to the initial setting level.
25
100
Initial Setting Level 2. The Input Type parameter is displayed in the initial setting level.
Input Type
in-t
5
PID ON/OFF 3. Select the PID ON/OFF parameter by pressing the M Key.
cntl
onof
4. Check that the set value is onof (i.e., the default).
5. To return to the operation level, press the O Key for at least one second.
Next, set the set point value.
Setting the SP
Operating Procedure In this example, the set point is set to 200. The set value (i.e., the SP) is
shown at the bottom of the display.
Operation Level 1. Select the Process Value/Set Point parameter in the operation level.
C PV/SP
25
100
C 2. Use the U and D Keys to set the SP. (In this example, it is set to 200.)
25 The new set value can be saved by pressing the M Key, or it will go into
effect after two seconds have elapsed.
200
Next, set the hysteresis.
61
Determining PID Constants (AT, ST, Manual Setup) Section 3-8
Setting the Hysteresis

Operating Procedure Set the hysteresis to 2.0C.
Operation Level 1. Press the O Key to move from the operation level to the adjustment level.
C PV
25
200
Adjustment Level 2. The Adjustment Level Display parameter will be displayed in the adjust-
Adjustment ment level.
1.adj Level Display
C Hysteresis 3. Select the Hysteresis (Heating) parameter by pressing the M Key.

hys (Heating)
1.0
C 4. Press the U and D Keys to set the hysteresis (2.0 in this example). Ei-
hys ther press the M Key or wait for at least two seconds after setting the hys-
teresis value to confirm the setting.
2.0
5. To return to the operation level, press the O Key.
3-8 Determining PID Constants (AT, ST, Manual Setup)

3-8-1 AT (Auto-tuning)
When AT is executed, the optimum PID constants for the set point at that
at time are set automatically. A method (called the limit cycle method) for
forcibly changing the manipulated variable and finding the characteristics
of the control object is employed.
Either 40% AT or 100% AT can be selected depending on the width of MV
variation in the limit cycle. In the AT Execute/Cancel parameter, specify
at-2 (100% AT) or at-1 (40% AT). To cancel AT, specify off (AT can-
cel).
Only 100% AT can be executed for heating and cooling control.
AT cannot be executed when control has stopped or during ON/OFF con-
trol.
The results of AT are reflected in the Proportional Band (P), Integral Time
(I), and Derivative Time (D) parameters in the adjustment level.
Adjustment Level
C Proportional Band
p
(0
Integral Time
i
233
Derivative Time
d
40
62
AT Operations AT is started when either at-2 (100% AT) or at-1 (40% AT) is specified for
the AT Execute/Cancel parameter. During execution, the AT Execute/Cancel
parameter on the No. 1 display flashes. When AT ends, the AT Execute/Can-
cel parameter turns OFF, and the No. 1 display stops flashing.
AT Execute/Cancel
at at No. 1 display
off at-2
100% AT execution in progress
If you move to the operation level during AT execution, the No. 2 display
flashes to indicate that AT is being executed.
PV/SP C C
25 25
100 100 No. 2 display
AT execution in progress
Only the Communications Writing, RUN/STOP, AT Execution/Cancel, and Pro-

gram Start parameters can be changed during AT execution. Other parame-
ters cannot be changed.
AT Calculated Gain
The AT Calculated Gain parameter sets the gain for when PID values are cal-
culated using AT. When emphasizing response, decrease the set value. When
emphasizing stability, increase the set value.
AT Hysteresis
The AT Hysteresis parameter sets the hysteresis when switching ON and OFF
for the limit cycle operation during auto-tuning.
Limit Cycle MV Amplitude
The Limit Cycle MV Amplitude parameter sets the MV amplitude for limit cycle
operation during auto-tuning.
Note This setting is disabled for 100% AT.
40% AT
The width of MV variation in the limit cycle can be changed in the Limit Cycle
MV Amplitude parameter, but the AT execution time may be longer than for
100% AT. The limit cycle timing varies according to whether the deviation (DV)
at the start of auto-tuning execution is less than 10% FS.
Deviation 10% FS Deviation < 10% FS
PV Limit Cycle MV PV Limit Cycle MV
Amplitude 40% Amplitude 40%
SP SP
Deviation: Deviation:
10% FS 10% FS
Time Time
AT started AT ended AT started AT ended
63
100% AT
Operation will be as shown in the following diagram, regardless of the devia-
tion (DV) at the start of AT execution. To shorten the AT execution time, select
100% AT.
PV Limit Cycle MV
Amplitude 100%
SP
Time
AT started AT ended
Note The Limit Cycle MV Amplitude parameter is disabled.
Operating Procedure This procedure executes 40%AT.
Adjustment Level 1. Press the O Key to move from the operation level to the adjustment level.
AT Execute/
at Cancel
off
2. Press the U Key to select at-1. The No. 1 display for AT Execute/Cancel
at will flash during AT execution.
at-1
3. off will be displayed when AT ends.
at
off
Operation Level 4. To return to the operation level, press the O Key.
C PV
25
0
3-8-2 ST (Self-tuning)
ST (self-tuning) is a function that finds PID constants by using step response
st tuning (SRT) when Controller operation begins or when the set point is
changed.
Once the PID constants have been calculated, ST is not executed when the
next control operation is started as long as the set point remains unchanged.
ST (self-tuning) is enabled when the ST parameter is set to ON in the initial
setting level.
When the ST function is in operation, be sure to turn the power supply of the
load connected to the control output ON simultaneously with or before starting
Controller operation.
When executing self-tuning, turn ON power for the load (e.g., heater) at the
same time as or before supplying power to the Digital Temperature Controller.
If power is turned ON for the Digital Temperature Controller before turning ON
power for the load, self-tuning will not be performed properly and optimum
control will not be achieved.
64
Note PID Constants

When control characteristics are already known, PID constants can be set
directly to adjust control. PID constants are set in the Proportional Band (P),
Integral Time (I), and Derivative Time (D) parameters in the adjustment level.
Operating Procedure This procedure executes self-tuning (ST).
Initial Setting Level 1. Press the O Key for at least three seconds to move from the operation
Input Type level to the initial setting level.
in-t
5
ST 2. Select the ST parameter by pressing the M Key.
st 3. Press the U Key to select on. ON is the default.
on
The temperature display flashes during self-tuning (ST) execution.
C PV
25
100
Startup Conditions Self-tuning by step response tuning (SRT) is started when the following condi-
tions are met after program execution is started and the set point is changed.
At start of operation When set point is changed
1. The set point at the start of operation 1. The new set point differs from the set
differs from the set point when the pre- point used when the previous SRT was
vious SRT was executed. (See note 1.) executed. (See note 1.)
2. The difference between the tempera- 2. The set point change width is greater
ture at the start of operation and the set both of the following: (Present propor-
point is greater both of the following: tional band 1.27 + 4C) and the ST
(Present proportional band 1.27 + stable range.
4C) and the ST stable range. 3. During reverse operation, the new set
3. The temperature at the start of opera- point is larger than the set point before
tion is lower than the set point during the change; and during direct opera-
reverse operation, and is larger than tion, the new set point is smaller than
the set point during direct operation. the set point before the change.
4. There is no reset from input errors. 4. The temperature is stable. (See note
2.) (Equilibrium with the output amount
at 0% when the power is turned ON is
also all right.) (See note 3.)
Note (1) The previous SRT-implemented set point is the set point that was used for
calculating the PID constants for the previous SRT.
(2) In this state, the measurement point is within the ST stable range.
(3) In this state, the change width of the PV every 60 seconds is within the
ST stable range or less.
In the following instances, PID constants are not changed by self-tuning (ST)
for the present set point.
1,2,3... 1. When the PID constants have been changed manually with ST set to ON.
2. When auto-tuning (AT) has been executed.
ST Stable Range
Operating Procedure The ST stable range determines the condition under which ST (self-tuning)
functions.
65
This procedure sets the ST stable range to 20.0C.

Advanced Function Setting Level 1. Select the ST Stable Range parameter by pressing the M Key in the ad-
C ST Stable vanced function setting level.
st-b Range
1%0
C 2. Use the U Key to set the parameter to 20.0C.
st-b
2*0
3-8-3 RT (Robust Tuning)

When AT or ST is executed with RT selected, PID constants are automat-
rt ically set that make it hard for control performance to degenerate even
when the characteristics of the controlled object are changed.
RT can be set in the advanced function setting level when PID control has
been set.
The RT mode cannot be selected while an analog input is set.
Selecting the RT mode in the following cases will help to prevent hunting
from occurring.
When the set temperature is not constant and is changed in a wide
range
When there are large variations in ambient temperatures due to factors
such as seasonal changes or differences between day and night tem-
peratures
When there are large variations in ambient wind conditions and air flow
When heater characteristics change depending on the temperature
When an actuator with disproportional I/O, such as a phase-control-
type power regulator, is used
When a rapidly heating heater is used
When the control object or sensor has much loss time
When hunting occurs in normal mode for any reason
PID constants are initialized to the factory settings by switching to RT
mode.
When the RT mode is selected, the derivative time setting unit be-
comes the second.
RT Features Even when hunting occurs for PID constants when AT or ST is executed
in normal mode, it is less likely to occur when AT or ST is executed in RT
mode.
Temperature Temperature
Much hunting occurs. Hunting is reduced.
Set value Set value
Time Time
Start of control Start of control
66
When the temperature (PV) falls short of the set point for the PID con-
stants when using AT or ST in normal mode, executing AT or ST in RT
mode tends to improve performance.
Temperature Temperature
Set value Set value
Time Time
Start of control Start of control
When the manipulated variable (MV) is saturated, the amount of over-

shooting may be somewhat higher in comparison to PID control based on
AT or ST in normal mode.
Operating Procedure This procedure selects RT mode.
25
100
Initial Setting Level 2. Select the Move to Advanced Function Setting Level parameter by press-
Input Type ing the M Key.
in-t
5
Initial Setting Level 3. Use the D Key to enter 169 (the password).
Move to Ad-
Setting Level
0
Advanced Function Setting Level It is possible to move to the advanced function setting level by pressing
Parameter the M Key or leaving the setting for at least two seconds.
init Initialization
off
Advanced Function Setting Level 4. Press the M Key to select rt.
RT
rt
off
5. Press the U Key to select on. off is the default.
rt
on
Initial Setting Level 6. To return to the initial setting level, press the O Key for at least one sec-
Input Type ond.
in-t
5
67
C PV/SP
25
100
3-8-4 Manual Setup

Individual PID constants can be manually set in the Proportional Band, Inte-
gral Time, and Derivative Time parameters in the adjustment level.
Operating Procedure In this example, the Proportional Band parameter is set to 10.0, the Integral
Time parameter to 250, and the Derivative Time parameter to 45.
Adjustment
l.adj Level Display
C Proportional 2. Press the M Key to select the proportional band parameter.
p Band
8.0
C 3. Use the U and D Keys to set 10.0.
p
10.0
Integral Time 4. Press the M Key to select the Integral Time parameter.
i
233
5. Use the U and D Keys to set 250.
i
250
Derivative Time 6. Select the Derivative Time operation by pressing the M Key.
d
40
7. Use the U and D Keys to set 45.
d
45
8. To return to the operation level, press the O Key.
Note Proportional Action

When PID constants I (integral time) and D (derivative time) are set to 0, con-
trol is executed according to proportional action. As the default, the center
value of the proportional band becomes the set point.
Related parameter: Manual reset value (adjustment level)
68
Alarm Outputs Section 3-9
When P (Proportional Band) Is Adjusted

Increased The curve rises gradually, and a long
Set stabilization time is created, but over-
value
shooting is prevented.
Decreased Overshooting and hunting occur, but

Set the set value is quickly reached and the
value temperature stabilizes.
When I (Integral Time) Is Adjusted

Increased It takes a long time to reach the set
Set point.
value
It takes time to achieve a stable state,
but overshooting, undershooting, and
hunting are reduced.
Decreased Overshooting and undershooting occur.
Set
Hunting occurs.
value
The Controller starts up faster.
When D (Derivative Time) Is Adjusted

Increased Overshooting, undershooting, and sta-
Set bilization times are reduced, but fine
value
hunting occurs on changes in the curve
itself.
Decreased Overshooting and undershooting
Set
value
increase, and it takes time to return to
the set point.
3-9 Alarm Outputs

Alarms can be used by the E5CN-@2@@@ (2 auxiliary outputs), E5AN/
E5EN-@1@@@ (1 auxiliary output), E5AN/E5EN-@3@@@ (3 auxiliary out-
puts), the E5CN-@1@@@U (1 auxiliary output), the E5CN-@2@@@U (2
auxiliary outputs), E5GN-@1@@@ (1 auxiliary output), and E5GN-
@2@@@ (2 auxiliary outputs).
Alarms can also be used by setting the Control Output 1 Assignment or
Control Output 2 Assignment parameter to any of the alarms from alarm 1
to 3. The alarm output condition is determined by a combination of the
alarm type, alarm value, alarm hysteresis, and the standby sequence.
For details, refer to 4-2 Alarm Hysteresis.
This section describes the Alarm Type, Alarm Value, Upper-limit Alarm
and Lower-limit Alarm parameters.
3-9-1 Alarm Types

Set value Alarm type Alarm output operation Description of function
When alarm value X When alarm value X
is positive is negative
0 Alarm function OFF Output OFF No alarm
1 (See note Upper- and lower-limit L H See note 2. Set the deviation in the set point by
ON
1.) OFF setting the alarm upper limit (H)
SP
and alarm lower limit (L).
2 Upper-limit X X Set the upward deviation in the set
ON ON
OFF OFF point by setting the alarm value
SP SP
(X).
69

3 Lower-limit X X Set the downward deviation in the
ON ON
OFF OFF set point by setting the alarm value
SP SP
(X).
ON
1.) range OFF setting the alarm upper limit (H)
SP
5 (See note Upper- and lower-limit L H See note 4. A standby sequence is added to
ON
1.) with standby sequence OFF
SP
the upper- and lower-limit alarm
See note 5. (1). (See note 6.)
6 Upper-limit with standby X X A standby sequence is added to

ON ON
sequence OFF OFF the upper-limit alarm (2). (See note
SP SP
6.)
7 Lower-limit with standby X X A standby sequence is added to
ON ON
sequence OFF OFF the lower-limit alarm (3). (See note
SP SP
6.)
8 Absolute-value upper- X X The alarm will turn ON if the pro-
ON ON
limit OFF OFF cess value is larger than the alarm
0 0
value (X) regardless of the set
point.
9 Absolute-value lower-limit X X The alarm will turn ON if the pro-
ON ON
OFF OFF cess value is smaller than the
0 0
alarm value (X) regardless of the
set point.
10 Absolute-value upper- X X A standby sequence is added to
ON ON
limit with standby OFF OFF the absolute-value upper-limit
0 0
sequence alarm (8). (See note 6.)
11 Absolute-value lower-limit X X A standby sequence is added to
ON ON
with standby sequence OFF OFF the absolute-value lower-limit
0 0
alarm (9). (See note 6.)
12 LBA (alarm 1 type only) --- Refer to page 118. (See note 7.)
13 PV change rate alarm --- Refer to page 72. (See note 8.)
Note (1) With set values 1, 4, and 5, the upper- and lower-limit values can be set
independently for each alarm type, and are expressed as L and H.
(2) Set value: 1 (Upper- and lower-limit alarm)
Case 1 Case 2 Case 3 (Always ON)
H < 0, L < 0
L H SP SP L H H SP L
H < 0, L > 0
H < 0, L > 0 H > 0, L < 0
H L SP |H| |L|
|H| < |L| |H| > |L|
H > 0, L < 0
SP H L |H| |L|
(3) Set value: 4 (Lower limit range)

Case 1 Case 2 Case 3 (Always OFF)
H < 0, L < 0
H < 0, L > 0 H > 0, L < 0 H < 0, L > 0
|H| < |L| |H| > |L| H L SP |H| |L|
H > 0, L < 0
SP H L |H| |L|
(4) Set value: 5 (Upper- and lower-limit with standby sequence)

For the lower-limit alarms in cases 1 and 2 above, the alarm is always
OFF if upper- and lower-limit hysteresis overlaps.
In case 3, the alarm is always OFF.
70

The alarm is always OFF if upper- and lower-limit hysteresis overlaps.
(6) Refer to 4-2-1 Standby Sequence for information on the operation of the
standby sequence.
(7) Refer to 4-12-1 Loop Burnout Alarm (LBA).
(8) Refer to PV Change Rate Alarm on page 72.
Set the alarm type independently for each alarm in the Alarm 1 to 3 Type
parameters in the initial setting level. The default is 2 (Upper-limit alarm).
3-9-2 Alarm Values

Alarm Lower Alarm values are indicated by X in the table on the previous page. When
al1l Limit Value the upper and lower limits are set independently, H is displayed for
upper limit values, and L is displayed for lower limit values.
al2l To set the alarm value upper and lower limits for deviation, set the upper
and lower limits in each of the Alarm 1 to 3 Upper Limit, and Alarm 1 to 3
al3l Lower Limit parameters in the operation level.
Alarm Upper
al1h Limit Value
al2h
al3h
Alarm Value
al-1
al-2
al-3
Operating Procedure This procedure sets alarm 1 as an upper-limit alarm. The related parameters
and settings are shown below. The alarm is output when the set point
exceeds 10C. (In this example, the temperature unit is C.)
Alarm 1 type = 2 (Upper-limit alarm)
Alarm value 1= 10
in-t
5
Alarm 1 Type 2. Select the Alarm 1 Type parameter by pressing the M Key. Confirm that
alt1 the set value is 2. The default value is 2 (Upper-limit alarm).
2
C PV/SP 3. To return to the operation level, press the O Key for at least one second.
25
100
71
C Alarm Value 1 4. Select the Alarm Value 1 parameter by pressing the M Key.
al-1
0
C 5. Use the U Key to set the parameter to 10.
al-1
10
PV Change Rate Alarm The change width can be found for PV input values in any set period. Differ-
ences with previous values in each set period are calculated, and an alarm is
output if the result exceeds the alarm value. The PV rate of change calculation
period can be set in units of 250 ms.
If a positive value is set for the alarm value, the PV will operate as a change
rate alarm in the rising direction. If a negative value is set, the PV will operate
as a change rate alarm in the falling direction.
Precaution
If a shorter PV rate of change calculation period is set, outputs set for the PV
change rate alarm function may repeatedly turn ON and OFF for a short
period of time. It is therefore recommended that the PV change rate alarm be
used with the alarm latch turned ON.
PV
Time
Alarm value
0
PV change width for PV rate
of change calculation period
ON ON
OFF OFF
Alarm function
Parameter name Setting range Unit Default

PV Rate of Change Calcu- 1 to 999 Sampling cycle 4 (1 s)
lation Period
72
Using Heater Burnout, Heater Short, and Heater Overcurrent Alarms Section 3-10
3-10 Using Heater Burnout, Heater Short, and Heater

Overcurrent Alarms
3-10-1 Heater Burnout, Heater Short, and Heater Overcurrent Alarm
Operations
Heater burnout detection and heater overcurrent detection are executed
by measuring heater current while the control output (heating) is ON, and
heater short detection is executed by measuring heater current while it is
OFF. For details, refer to the following table. (Heater burnout detection,
heater short detection, and heater overcurrent detection cannot be used
with the control output for cooling.)
Control output (heating) status Power to heater HB alarm HS alarm Heater overcurrent
Control output Operation output output alarm output
(heating) indicator
ON Lit Yes (Normal) (See note 1.) OFF --- ---
No (Heater burnout) ON --- ---
OFF Not lit Yes (HS alarm) --- ON ---
No (Normal) (See note 2.) --- OFF ---
ON Lit Normal --- --- OFF
Heater overcurrent status --- --- ON
(See note 3.)
Ton Toff
(See note 4.) (See note 5.)
ON
Control output (heating)
OFF
Note (1) In the above diagram, power is considered to be ON (normal) if the heater
current is greater than the heater burnout detection current during the Ton
interval. If the heater is burned out, the measured current decreases and
falls below the heater burnout detection value. The output is then activat-
ed as the heater burnout alarm.
(2) In the above diagram, power is considered to be OFF (normal) if the leak-
age current is less than the HS alarm current during the Toff interval. If
the SSR output is short-circuited, the measured current increases be-
yond the HS alarm value. The output is then activated as the HS alarm.
(3) In the above diagram, it is regarded as normal when the heater current is
less than the heater overcurrent detection current during the Ton period.
Current is increased when excessive current flows to the heater, causing
the heater overcurrent detection value to be exceeded and an OC (heater
overcurrent) alarm to be output.
(4) Heater burnout and heater overcurrent are not detected if the control out-
put (heating) ON time (Ton) is 100 ms or less.
(5) HS alarms are not detected if the control output (heating) OFF time (Toff)
is 100 ms or less.
73
For Controllers with heater burnout, HS, and heater overcurrent alarms,
an OR output is established between the ALM 1 function and the alarms.
If the ALM1 function is to be used for the heater burnout, HS, and heater
overcurrent alarms only, set 0 as the alarm 1 type (i.e., do not use ALM1).
Turn the heater power ON simultaneously or before turning ON the E5@N
power. If the heater power is turned ON after turning ON the E5AN power,
the HB alarm will be activated.
Control is continued even when the heater burnout, HS, or heater over-
current alarm is active.
The rated current value may sometimes differ slightly from the actual cur-
rent flowing to the heater.
Use the Heater Current 1 Value Monitor, Heater Current 2 Value Monitor,
Leakage Current 1 Monitor, and Leakage Current 2 Monitor parameters to
check the actual current being used.
If there is little difference between the current in normal and abnormal
states, detection may become unstable. To stabilize detection, set a cur-
rent value difference of at least 1.0 A for heaters of less than 10.0 A, and
at least 2.5 A for heaters of 10.0 A or more. If the heater current is too low,
loop the load line several times through a CT, as shown in the diagram
below. Looping it through once will double the detection current.
Load line
CT
3-10-2 Installing Current Transformers (CT)

This function can be used with E5@N models that have the HB alarm, HS
alarm, and OC alarm.
For the E5CN, connect the CT in advance to terminals 14 and 15 (CT1),
or 13 and 15 (CT2). For the E5AN/E5EN, connect the CT in advance to
terminals 14 and 15 (CT1) or 15 and 16 (CT2). For the E5GN, connect the
CT in advance to terminals 7 and 8 (CT1). Then pass the heater power
line through the CT's hole. For specifications, models and dimensions of
current transformers that can be used with this Controller, refer to Appen-
dix Current Transformer (CT) on page 279.
Single-phase Heaters For single-phase heaters, install the CT in the position shown in the following
diagram.
Load Load (such as a heater)

AC line
CT
Product
To CT input
Three-phase Heaters (E5AN-@@HH@-N, E5EN-@@HH@-N, and E53-CN@@HHN2 (for E5CN) 3-phase

Heater Detection Models)
When a 3-phase power supply is used, regardless of the types of connecting
lines, two current transformers (CTs) are required to detect heater burnout,
HS, and OC.
1,2,3... 1. Delta connecting lines: Refer to the following diagram for CT installation
positions.
Note Heater voltage fluctuations are not considered here, so be take that
into account when setting the detection current.
74
Lo
ad
ad
Lo
Load (such as a heater)
AC line Load
Product
To CT input
AC line
CT
Product
To CT input
2. Star connecting lines: Refer to the following diagram for CT installation po-
sitions.
Load
Lo
ad ad
AC line Lo
CT
Product
To CT input
CT
Product
To CT input
3. V connecting lines: Refer to the following diagram for CT installation posi-

tions.
CT
Product
ad
Lo
To CT input
Lo
ad
AC line
CT
Product
To CT input
3-10-3 Calculating Detection Current Values

Calculate the set value using the following equation:
Heater Burnout Detection 1/2 set value = Normal current value + Burnout current value
2
HS Alarm 1/2 set value = Leakage current value (output OFF) + HS current value
2
Heater overcurrent 1/2 set value = Normal current value + Overcurrent value
2
To set the current for heater burnout when two or more heaters are con-
nected through the CT, use the value from when the heater with the small-
est current burns out. If all of the heaters have the same current, use the
value from when any one of them burns out.
75
Make sure that the following conditions are satisfied:

Heater with a current of less than 10.0 A:
(Current value at normal operation) (Current value at heater burnout)
1A
When the difference is less than 1 A, detection is unstable.
Heater with a current of 10.0 A or more:
(Current value at normal operation) (Current value at heater burnout)
2.5 A
When the difference is less than 2.5 A, detection is unstable.
The setting range is 0.1 to 49.9 A. Heater burnout, HS, and heater over-
current are not detected when the set value is 0.0 or 50.0. When the set
value is 0.0, the heater burnout alarm is always OFF, the HS alarm is
always ON, and the heater overcurrent alarm is always ON. When the set
value is 50.0, the heater burnout alarm is always ON, the HS alarm is
always OFF, and the heater overcurrent alarm is always OFF.
Set the total current value for normal heater operation to 50 A or less.
When a current value of 55.0 A is exceeded, ffff is displayed in the
Heater Current 1 (or 2) Value Monitor and Leakage Current 1 (or 2) Moni-
tor parameters.
3-10-4 Application Examples

Single-phase Heaters Example: Using a 200-VAC, 1-kW Heater
Normal Burnout
5 A AC line AC line
200 V Load 200 V Burnout Load Load (such as a heater)

5 A 0A
CT CT
Product Product
To CT input To CT input
The heater power supply provides 5 A when the current is normal, and 0 A
when there is a burnout, so the heater burnout detection current is calculated
as follows:
(Normal current) + (Heater burnout current)
Heater burnout detection current =
2
5+0
= = 2.5 [A]
2
Example: Using Three 200-VAC, 1-kW Heaters
Normal Burnout
15 A 10 A
Load Load Load

200 V Load Load Load 200 V
Burn-
15 A 10 A out
Product
CT Product
CT
The heater power supply provides 15 A when the current is normal, and 10 A
when there is a burnout, so the heater burnout detection current is calculated
as follows:
76
(Normal current) + (Heater burnout current)

Heater burnout detection current =
2
15 + 10
= = 12.5 [A]
2
Three-phase Heaters Delta Connecting Lines

Normal
17.3 A
Lo
ad
200 V
ad
Lo
17.3 A
200 V Load
200 V Product
17.3 A To CT input
CT
Product
To CT input
The current when each phase is normal is 17.3 A ( 3 10 A).

Burnout Burnout
Burnout
10 A
Burnout
ad
ad
Lo
200 V 200 V
Lo
Lo
ad
Lo
ad
15 A 200 V 17.3 A
200 V Load Load
CT CT
200 V Product 200 V Product
15 A CT 10 A CT
Product Product
Current when there is a burnout = 10 A 3 Current when there is a burnout = 10 A 3
(3/2) = 15 A (1/3) = 10 A
The heater burnout current when there is a burnout at the load line is as fol-
lows:
(Heater burnout detection current) = (17.3 + 15) / 2 16.1 [A]
The heater burnout current when there is a burnout at the load is as follows:
(Heater burnout detection current) = (17.3 + 10) / 2 13.65 [A]
To enable detection in either case, use 16.1 A as the heater burnout detection
current.
77
Star Connecting Lines

Normal
5.8 A
Load
200 V Load (such as a heater)
200 V
Lo
ad ad
5.8 A Lo
CT
200 V Product
To CT input
5.8 A CT
Product
To CT input
The current when each phase is normal is 5.8 A ( 10 A (1 /3)).

Burnout
Burnout
5 A
Load
Load
Load (such as a heater) Load (such as a heater)
200 V 200 V
Lo Lo
200 V ad ad 200 V ad ad
5 A Lo 5 A Lo
CT CT
To CT input To CT input Burnout
5 A CT CT
Product Product
Current when there is a burnout = 10 A (1/3) Current when there is a burnout = 10 A (1/3)
(3/2) = 5 A (3/2) = 5 A
The heater burnout detection current for this connecting line is 5.4 A (= (5.8 +
5) / 2).
78
V Connecting Lines
Example: Using Two 200-VAC, 2-kW Heaters
Normal
10 A
CT
Product
ad
200 V
Lo
To CT input
17.3 A
200 V
200 V
Lo
ad
10 A
CT
Product
To CT input
Burnout
5 A 10 A
CT CT
ad
ad
Lo
Lo
10 A
200 V 200 V
200 V 200 V
Lo
Lo
ad
ad
Burnout
5 A
CT CT
Product Product
Current when there is a burnout = 10 A (1/2) Current when there is a burnout = 0 A

=5A
The heater burnout current when there is a burnout at the common is as fol-
lows:
Heater burnout detection current = (10 + 5) / 2 7.5 [A]
The heater burnout current when there is a burnout at the load is as follows:
Heater burnout detection current = (10 + 0) / 2 5 [A]
To enable detection in either case, use 7.5 A as the heater burnout detection
current.
79
3-10-5 Settings: HB Alarm

To activate the heater burnout alarm, set the HB ON/OFF parameter to ON in
the advanced function setting level and set the Heater Burnout Detection 1
and Heater Burnout Detection 2 parameters in the adjustment level.
Operating Procedure This procedure sets the Heater Burnout Detection 1 parameter to 2.5.
Moving to the Advanced Function Setting Level
The Heater Burnout Detection parameter setting is already ON by default, so
set the Heater Burnout Detection 1 parameter.
Operation Level 1. Move to the advanced function setting level.
C PV/SP Press the O Key for at least three seconds to move from the operation
25 level to the initial setting level.
100
Initial Setting Level 2. Select Move to Advanced Function Setting Level by pressing the M Key.
Input Type (For details on moving between levels, refer to 4-8 Moving to the Ad-
in-t vanced Function Setting Level.)
5
Initial Setting Level 3. Press the D Key to enter the password (169), and move from the initial
setting level to the advanced function setting level.
amov
-169
Advanced Function Setting Level The top parameter in the advanced function setting level is displayed.
init Moves to Ad-

vanced Function
Setting Level
off
Heater Burnout 4. Select the Heater Burnout Detection parameter by pressing the M Key.
hbu Detection Check that this parameter is set to ON (the default).
Next, set the Heater Burnout Detection 1 parameter.
on
Setting Heater Burnout Detection

Operation Level 5. Press the O Key for at least one second to move from the advanced
C PV/SP function setting level to the initial setting level. Press the O key again for
25 at least one second to move to the operation level.
100
Adjustment Level 6. Press the O Key for less than one second to move from the operation
Adjustment Level level to the adjustment level.
l.adj Display
Heater Current 7. Select the Heater Current 1 Value Monitor parameter by pressing the M
ct1 1 Value Monitor Key. Check the current value. Next, set the Heater Burnout Detection 1
parameter.
0.0
Heater Burnout 8. Select the Heater Burnout Detection 1 parameter by pressing the M Key.
hb1 Detection 1 Refer to Calculating Detection Current Values on page 75 on when mak-
ing the settings.
0.0
80
9. For this example, set 2.5. To return to the operation level, press the O
hb1 Key for less than one second.
2.5
3-10-6 Settings: Heater Short Alarm

To activate the HS alarm, set the HS Alarm Use parameter to ON in the
advanced function setting level and set the HS Alarm 1 and HS Alarm 2
parameters in the adjustment level.
Operating Procedure This procedure sets the HS Alarm 1 parameter to 2.5.
The HS Alarm Use parameter setting is already ON by default, so set the HS
Alarm 1 parameter.
100
Initial Setting Level 2. Select Move to Advanced Function Setting Level by pressing the M Key.
Input Type (For details on moving between levels, refer to 4-8 Moving to the Ad-
in-t vanced Function Setting Level.)
5
amov
-169
Move to the
init Advanced
Function
off Setting Level
HS Alarm 4. Select the HS Alarm Use parameter by pressing the M Key.

hsu Use Check that this parameter is set to ON (the default).
Next, set the HS Alarm 1 parameter.
on
81
HS Alarm Settings
100
l.adj Display
Leakage Current 7. Select the Leakage Current 1 Monitor parameter by pressing the M Key.
lcr1 1 Monitor Check the current value. Next, set the HS Alarm 1 parameter.
0.0
HS Alarm 1 8. Select the HS Alarm 1 parameter by pressing the M Key. Refer to Calcu-
hs1 lating Detection Current Values on page 75 when setting the values.
50.0
hs1 Key for less than one second.
2.5
3-10-7 Settings: Heater Overcurrent Alarm

To activate heater overcurrent alarm, set the Heater Overcurrent Use parame-
ter to ON in the advanced function setting level and set the Heater Overcur-
rent Detection 1 and Heater Overcurrent Detection 2 parameters in the
adjustment level.
Operating Procedure This procedure sets the Heater Overcurrent Detection 1 parameter to 20.0.
The default setting for the Heater Overcurrent Use parameter is ON, so set
the Heater Overcurrent Detection 1 parameter.
100
Initial Setting Level 2. Press the M Key to select the Move to Advanced Function Setting Level
Input Type parameter. (For details on moving between levels, refer to 4-8 Moving to
in-t the Advanced Function Setting Level.)
5
amov
-169
82
Move to the
init Advanced
Function
off Setting Level
Heater 4. Press the M Key to select the Heater Overcurrent Use parameter.
ocu Overcurrent
Use
Check that this parameter is set to ON (the default), and then set the
Heater Overcurrent Detection 1 parameter.
on
Setting Heater Overcurrent Detection
100
l.adj Display
Heater Current 7. Press the M Key to select the Heater Current 1 Value Monitor parameter.
ct1 1 Value Monitor Check the current value, and then set the Heater Overcurrent Detection
parameter.
0.0
Heater 8. Press the M Key to select the Heater Overcurrent Detection 1 parameter.
oc1 Overcurrent
Detection 1
Refer to Calculating Detection Current Values on page 75 when setting
the values.
50.0
oc1 Key for less than one second.
20.0
83
Setting the No. 3 Display Section 3-11
3-11 Setting the No. 3 Display

This section describes how to set the No. 3 Display (E5AN/EN). The Multi-SP,
MV, or soak time remain can be displayed on the No. 3 display.
3-11-1 PV/SP Display Selection

The following table shows the set values and display contents for the PV/SP
Display selection.
Set value Display contents
0 Only PV/SP is displayed (with no No. 3 display.)
1 PV/SP/Multi-SP and PV/SP/MV are displayed in order. (See note.)
2 PV/SP/MV and PV/SP/Multi-SP are displayed in order. (See note.)
3 Only PV/SP/Multi-SP is displayed.
4 Only PV/SP/MV is displayed. (See note.)
5 PV/SP/Multi-SP and PV/SP/Soak time remain are displayed in order.
6 PV/SP/MV and PV/SP/Soak time remain are displayed in order. (See
note.)
7 Only PV/SP/Soak time remain is displayed.
A 2-level display is set when shipped from the factory. (set value: 0)
A 3-level display is activated if parameters are initialized. (set value: 4)
Note For details on setting the MV for heating and cooling control, refer to MV Dis-
play for Heating and Cooling Control below.
When 1, 2, 5, or 6 is selected, press the M Key to display the next value set
for the PV/SP display (display 2).
Example: When the PV/SP Display Screen Parameter Is Set to 2
Operation Level
PV/SP (Display 1) PV/SP (Display 2)
Press the
C
C
25 M key 25
100 100
50.0 sp0
PV/SP/MV PV/SP/Multi-SP
MV Display for Select either the manipulated variable (heating) or manipulated variable (cool-
Heating and Cooling ing) as the MV to be displayed for PV/SP/MV during heating and cooling con-
Control trol. The MV Display Selection parameter is displayed only when heating/
cooling control is being performed and PV/SP/MV is selected in the PV/SP
Display Screen parameter or a Monitor/Setting Item Display parameter.
Parameter name Set value Symbol Display contents
MV Display Selection O o Manipulated variable
(heating)
C-O c-o Manipulated variable
(cooling)
84
Operating Procedure This procedure displays PV/SP/MV and PV/SP/Multi-SP on the Process
Value/Set Point display. The PV/SP Display Screen Selection parameter is set
to 2.
PV/SP
C
25
100
Initial Setting Level 2. Press the M Key to select the Move to Advanced Function Setting Level
Input Type parameter.
in-t
5
Initial Setting Level 3. Use the D Key to enter the password (169).
Move to It is possible to move to the advanced function setting level by either
amov Advanced pressing the M Key or waiting two seconds without pressing any key.
Function Setting
-169 Level
Advanced Function Setting Level 4. Press the M Key to select the PV/SP Display Screen Selection parame-
ter.
init Parameter
Initialization
off
Advanced Function Setting Level 5. Use the U and D Keys to set 2.

PV/SP Display
spdp Screen Selection
4
6. Press the O Key for at least one second to move from the advanced
spdp function setting level to the initial setting level.
2
Initial Setting Level 7. Press the O Key for at least one second to move from the initial setting
Input Type level to the operation level.
in-t The MV will be displayed on the No. 3 display.
5
Operation Level 8. Press the M Key to confirm that the Multi-SP is displayed on the No. 3
PV/SP
display.
C
25
100
50.0
Operation Level
C PV/SP
25
100
sp0
85
86
SECTION 4
Applications Operations
This section describes scaling, the SP ramp function, and other special functions that can be used to make the most of the
functionality of the E5CN, E5AN, and E5EN Digital Temperature Controllers.
4-1 Shifting Input Values. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89

4-1-1 Shifting Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
4-1-2 How to Calculate Input Shift Values for a 2-point Shift. . . . . . . . . . 90
4-2 Alarm Hysteresis. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
4-2-1 Standby Sequence. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
4-2-2 Alarm Latch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
4-3 Setting Scaling Upper and Lower Limits for Analog Inputs . . . . . . . . . . . . . 94
4-3-1 Analog Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
4-4 Executing Heating/Cooling Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
4-4-1 Heating/Cooling Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
4-4-2 Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
4-5 Using Event Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
4-5-1 Event Input Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
4-5-2 How to Use the Multi-SP Function. . . . . . . . . . . . . . . . . . . . . . . . . . 101
4-5-3 Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
4-5-4 Operation Commands Other than Multi-SP . . . . . . . . . . . . . . . . . . . 102
4-6 Setting the SP Upper and Lower Limit Values . . . . . . . . . . . . . . . . . . . . . . . . 104
4-6-1 Set Point Limiter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
4-6-2 Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
4-7 Using the SP Ramp Function to Limit the SP Change Rate . . . . . . . . . . . . . . 106
4-7-1 SP Ramp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
4-8 Moving to the Advanced Function Setting Level . . . . . . . . . . . . . . . . . . . . . . 108
4-9 Using the Key Protect Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
4-9-1 Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
4-9-2 Entering the Password to Move to the Protect Level . . . . . . . . . . . . 111
4-10 PV Change Color . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
4-10-1 PV Color Change Function. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
4-10-2 Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
4-11 Alarm Delays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116
4-11-1 Alarm Delays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116
4-12 Loop Burnout Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
4-12-1 Loop Burnout Alarm (LBA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
4-13 Performing Manual Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122
4-13-1 Manual Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122
4-14 Using the Transfer Output. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126
4-14-1 Transfer Output Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126
87
4-15 Using the Simple Program Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129
4-15-1 Simple Program Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129
4-15-2 Operation at the Program End . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132
4-15-3 Application Example Using a Simple Program . . . . . . . . . . . . . . . . 135
4-16 Output Adjustment Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136
4-16-1 Output Limits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136
4-16-2 MV at Stop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136
4-16-3 MV at PV Error . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137
4-17 Using the Extraction of Square Root Parameter . . . . . . . . . . . . . . . . . . . . . . . 137
4-18 Setting the Width of MV Variation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139
4-19 Setting the PF Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141
4-19-1 PF Setting (Function Key). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141
4-20 Counting Control Output ON/OFF Operations . . . . . . . . . . . . . . . . . . . . . . . . 143
4-20-1 Control Output ON/OFF Count Function . . . . . . . . . . . . . . . . . . . . . 143
4-21 Displaying PV/SV Status. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145
4-21-1 PV and SV Status Display Functions . . . . . . . . . . . . . . . . . . . . . . . . 145
4-22 Logic Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147
4-22-1 The Logic Operation Function (CX-Thermo) . . . . . . . . . . . . . . . . . . 147
4-22-2 Using Logic Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148
88
Shifting Input Values Section 4-1
4-1 Shifting Input Values

4-1-1 Shifting Inputs
The input shift matched to the sensor currently selected in the Input Type
parameter is displayed.
A 2-point shift is applied for infrared temperature sensors. A 2-point shift
can also be used if the Input Shift Type parameter (advanced function set-
ting level) is set to INS2 for a thermocouple or platinum resistance ther-
mometer.
There is no shift for analog inputs. Use scaling for fine adjustments.
One-point shift
With a 1-point shift, the value set for the Temperature Input Shift parame-
Temperature
ins Input Shift ter (adjustment level) is applied to each point in the entire temperature
input range. For example, if the input shift value is set to 1.2C, the pro-
cess value is treated as 201.2C after the input shift is applied when the
measured process value is 200C.
Temperature
Upper limit
After shifting
Before
shifting
Input shift value
Lower limit
Input
0
100
Operating Procedure In this example, the input from a K sensor is shifted by 1C using a 1-point
input shift.
Operation Level Operation Level
C
30
200
Adjustment
l.adj Level Display
C Temperature 2. Select the Temperature Input Shift parameter by pressing the M Key.
ins Input Shift
0.0
C 3. Press the U or D Key to set 1.0.
ins
1.0
Operation Level 4. To return to the operation level, press the O Key. The process value is
C
1C larger than before the shift was applied.
31
200
89
Two-point shift
Separate shift values can be set for the upper limit and lower limit of the
Upper-limit
insh Temperature
Input Shift Value
sensor input range for an infrared sensor as well as for a thermocouple or
platinum resistance thermometer with the Input Shift Type parameter set
Lower-limit to INS2. If different shift values are set for the upper limit and lower limit,
insl Temperature
Input Shift Value
then the slope of the line will be different before and after applying the
input shift. For example, if the upper-limit value is set to 2C and the
lower-limit value is set to 1C, the input temperature will be shifted by
1.5C for a 50% input, i.e., by the average of the upper-limit and lower-
limit values.
Set the upper-limit value in the Upper-limit Temperature Input Shift Value
parameter and the lower-limit value in the Lower-limit Temperature Input
Shift Value parameter.
Upper-limit temperature
Temperature input shift value
Upper limit
After shifting
Before shifting
Lower limit
Input
0
Lower-limit temperature 100
input shift value
4-1-2 How to Calculate Input Shift Values for a 2-point Shift

When an ES1B Infrared Temperature Sensor is connected to the E5CN, an
offset of several degrees to several tens of a degree can occur.
For this reason, offset the readout value using a 1-point or 2-point shift as
described in this section. This offset occurs because a bias current for detect-
ing a Controller sensor error flows to the output impedance of the infrared
temperature sensor.
Preparations
1,2,3... 1. Set a temperature range matching the input specifications of the infrared
temperature sensor. (The ES1B can be used with the E5@N only for a ther-
mocouple/resistance thermometer universal input.)
2. Prepare a thermometer capable of measuring the temperature of the con-
trol target as shown in Figure 1 so that a 1-point shift or 2-point shift can
be carried out.
3. The E53-CN@@P@N2 (for E5CN), E5AN-@@P@-N, or E5EN-@@P@-N
has a built-in external power supply for ES1B Infrared Temperature Sen-
sors. These E5CN models can be used as the power supply when using
ES1B. When ES1B are used with other E5CN models, provide a separate
power supply for the Infrared Temperature Sensors.
90
(C) Control target
Infrared Temperature
Sensor
Power supply
(B) Thermometer
Output
(A) E5CN/AN/EN Temperature Controller
Figure 1 Offset Configuration for an Infrared Temperature Sensor
Method for a 1-point Shift

1,2,3... 1. In the configuration shown in Figure 1, bring the set point to near the value
at which the temperature of the control target is to be controlled. Assume
that the control target temperature (C) and the thermometer temperature
(B) are the same.
C Upper-limit 2. Check the thermometer temperature (B) and the Controller readout (A).
insh Temperature
Input Shift
Subtract the Controller readout temperature (A) from the thermometer
temperature (B), and set insl and insh to the result as the input shift val-
10.0 Value
ue. The shift is illustrated in Figure 2.
C Lower-limit 3. After setting the input shift values, check the Controller readout (A) and the
insl Temperature
Input Shift thermometer temperature (B). If they are almost the same, this completes
10.0 Value shifting the temperature input.
Controller readout (A)
After shifting
Controller readout after
shifting (e.g., 120C) Input shift value (e.g., 10C)
Controller readout before
Before shifting
shifting (e.g., 110C)
Control target temperature (B)

0 Near set point
(e.g., 120C)
Figure 2 Illustration of 1-Point Shift
91
Method for a 2-point Use a 2-point input shift if you want to increase the accuracy of the readout
Shift values across the range of the Sensor.
1,2,3... 1. Shift the Controller readout at two points, near room temperature and near
the value at which the temperature of the control target is to be controlled.
For this reason, check the thermometer temperature (B) and Controller
readout (A) with the thermometer temperature near room temperature and
near the set point.
2.
Y1 is the Controller readout at room temperature before shifting and
X1 is the Controller readout at room temperature after shifting.
Y2 is the Controller readout at the set temperature before shifting and
X2 is the Controller readout at the set temperature after shifting.
Set the upper-limit temperature input shift and the lower-limit temper-
ature input shift using the following formulas based on the tempera-
tures before shifting (Y1 and Y2), the temperatures after shifting (X1
and X2), the set temperature upper limit (YH), and the set temperature
lower limit (YL). The shift is illustrated in Figure 3.
After shifting
Controller readout (A)
Upper-limit temperature input
shift value (e.g., 52.7C) insh
YH: Set temperature upper limit
(e.g., 260C) Before shifting
X2: Controller readout after shifting

(e.g., 110C)
Y2: Controller readout before shifting
(e.g., 105C)
Y1: Controller readout before shifting
(e.g., 40C)
X1: Controller readout after shifting
(e.g., 25C) Control target temperature (B)
Lower-limit temperature input 260C
shift value (e.g., 27.3C) insl 0 X1: Room temper- X2: Near set point (e.g., 110C)
ature (e.g., 25C)
YL: Set temperature lower limit
(e.g., 0C)
Figure 3 Illustration of 2-Point Shift
a. Lower-limit temperature input shift value
YL Y1
insl = {(X2 Y2) (X1 Y1)} + (X1 Y1)
Y2 Y1
b. Upper-limit temperature input shift value
YH Y1
insh = {(X2 Y2) (X1 Y1)} + (X1 Y1)
Y2 Y1
3. After setting the calculated values to insl and insh, check the Controller
readout (A) and thermometer temperature (B).
4. Here, offsets are set at two points, near room temperature and near the set
point. To improve accuracy within the measurement temperature range,
another point in the measurement temperature range other than the set
point should be set instead of room temperature.
92
Alarm Hysteresis Section 4-2
Example of a 2-point In this example, we use the ES1B K 0 to 260C specification. In equations 1
Temperature Input and 2, the set temperature lower limit YL is 0C and the set temperature upper
Shift limit YH is 260C. Check the temperature of the control target.
The temperature input offset values can be calculated as shown below when
the Controller readout Y1 is 40C for a room temperature X1 of 25C and
when the Controller readout Y2 is 105C for a set point temperature X2 of
110C.
Lower-limit Temperature Input Shift Value
C Lower-limit
0 40
insl Temperature
Input Shift
insl =
105 40
{(110 105) (25 40)} + (25 40) = 27.3 (C)
-27.3 Value
Upper-limit Temperature Input Shift Value
C Upper-limit 260 40
insh Temperature
Input Shift
insh =
105 40
{(110 105) (25 40)} + (25 40) = 52.7 (C)
52.7 Value
4-2 Alarm Hysteresis

The hysteresis of alarm outputs when alarms are switched ON/OFF can
be set as follows:
Upper-limit alarm Lower-limit alarm
Alarm hysteresis Alarm hysteresis
ON ON
OFF OFF
Alarm value Alarm value
Alarm hysteresis is set independently for each alarm in the Alarm Hyster-
esis 1 to Alarm Hysteresis 3 parameters (initial setting level).
The default is 0.2 (C/F) for Controllers with Thermocouple/Resistance
Thermometer Universal Inputs and 0.02% FS for Controllers with Analog
Inputs.
4-2-1 Standby Sequence

The standby sequence can be used so that an alarm will not be output
until the process value leaves the alarm range once and then enters it
again.
For example, with a lower limit alarm, the process value will normally be
below the set point, i.e., within the alarm range, when the power supply is
turned ON, causing an alarm to be output.
If the lower limit alarm with a standby sequence is selected, an alarm will
not be output until the process value increases above the alarm set value,
i.e., until it leaves the alarm range, and then falls back below the alarm set
value.
Restart The standby sequence is canceled when an alarm is output. It is, how-
ever, restarted later by the Standby Sequence Reset parameter
(advanced function setting level). For details, refer to the Standby
Sequence Reset parameter in SECTION 5 Parameters.
93
Setting Scaling Upper and Lower Limits for Analog Inputs Section 4-3
4-2-2 Alarm Latch

The alarm latch can be used to keep the alarm output ON until the latch is
canceled regardless of the temperature once the alarm output has turned
ON.
Any of the following methods can be used to clear the alarm latch.
Turn OFF the power supply. (The alarm latch is also cleared by switching
to the initial setting level, communications setting level, advanced function
setting level, or calibration level.)
Use the PF Key.
Use an event input.
For details on setting the PF Key, refer to 4-19 Setting the PF Key. For details
on setting events, refer to 4-5 Using Event Inputs.
Summary of Alarm The following figure summarizes the operation of alarms when the Alarm Type
Operation parameter is set to lower-limit alarm with standby sequence and close in
alarm is set.
Alarm type: Lower-limit alarm with standby sequence
PV
Alarm value
Alarm hysteresis
Time
Standby sequence
canceled ON
Alarm OFF
ON (closed)
Output OFF (open)
Parameters
Symbol Parameter: level Description
alh* Alarm 1 to 3 Hysteresis: Initial setting level Alarm
rest Standby Sequence: Advanced function setting level Alarm
Note * = 1 to 3
4-3 Setting Scaling Upper and Lower Limits for Analog Inputs
4-3-1 Analog Input
When an analog input is selected, scaling can be performed as needed
Scaling Upper Limit
in-h by the control application.
Scaling is set in the Scaling Upper Limit, Scaling Lower Limit, and Deci-
Scaling Lower Limit
in-l mal Point parameters (initial setting level). These parameters cannot be
used when a temperature input is selected.
Decimal Point
dp The Scaling Upper Limit parameter sets the physical quantity to be
expressed by the upper limit value of input, and the Scaling Lower Limit
parameter sets the physical quantity to be expressed by the lower-limit
value of input. The Decimal Point parameter specifies the number of digits
below the decimal point.
94
Executing Heating/Cooling Control Section 4-4
The following figure shows a scaling example for a 4 to 20 mV input.

After scaling, the humidity can be directly read. Here, one place below the
decimal point is set.
Display
(humidity)
Upper limit (95.0%)
Lower limit (10.0%)
Input (mA)
4
20
Operating Procedure In this example scaling is set to display 4 to 20 mA as 10.0% to 95.0%.

Initial Setting Level 1. Press the O Key for three seconds to move from the operation level to
Input Type the initial setting level.
in-t
0
Scaling Upper 2. Select Scaling Upper Limit parameter by pressing the M Key.
in-h Limit
100
3. Use the U and D Keys to set the parameter to 950.
in-h
950
Scaling Lower 4. Select the Scaling Lower Limit parameter by pressing the M Key.
in-l Limit
0
5. Press the U and D Keys to set 100.
in-l
100
Decimal Point 6. Select the Decimal Point parameter by pressing the M Key.
dp
0
7. Press the U and D Keys to set 1.
dp
1
8. To return to the operation level, press the O Key for one second.
4-4 Executing Heating/Cooling Control

4-4-1 Heating/Cooling Control
Heating/cooling control can be used on the E5CN-@M@-500 (with an E53-
CNQ@@N2), E5CN-@2M@-500, E5AN-@3@M@-500-N or E5EN-@3@M@-
500-N. Heating/cooling control operates when h-c (heating/cooling) is
selected for the Standard or Heating/Cooling parameter.
95
The following functions are assigned to outputs in the initial status.

Parameter name Symbol Initial status
Control Output 1 Assignment out1 Control output for heating
Control Output 2 Assignment out2 Not assigned.
(E5AN/EN only)
Each output assignment is automatically initialized as shown below when the

control mode is changed.
Example: E5CN
Parameter name Symbol Without control output 2 With control output 2
Standard Heating/cooling Standard Heating/cooling
Control Output 1 out1 Control output Control output Control output Control output
Assignment (heating) (heating) (heating) (heating)
Control Output 2 out2 Not assigned. (See Not assigned. (See Not assigned. Control output (coo-
Assignment note 1.) note 1.) ing)
Auxiliary Output 1 sub1 Alarm 1 (See note Alarm 1 (See note Alarm 1 (See note Alarm 1 (See note
Assignment 2.) 2.) 2.) 2.)
Auxiliary Output 2 sub2 Alarm 2 (See note Control output (coo- Alarm 2 Alarm 2
Assignment 3.) ing) (See note 3.)
Example: E5GN
Parameter name Symbol Standard Heating/cooling
Control Output 1 out1 Control output Control output
Assignment (heating) (heating)
Auxiliary Output 1 sub1 Alarm 1 (See note Control output (coo-
Assignment 2.) ing)
Auxiliary Output 2 sub2 Alarm 2 Alarm 2
Assignment
Note (1) No parameter assignment is displayed because there is no control output

2.
(2) The output set for the Auxiliary Output 1 Assignment parameter becomes
the program END output unless the program pattern is OFF.
(3) For the E5AN/EN, the Auxiliary Output 3 Assignment parameter is set for
control output (cooling) (the Auxiliary Output 2 Assignment parameter is
set for alarm 2).
The heating/cooling operation of the control outputs will switch when the
Direct/Reverse Operation parameter is set to direct.
When DRS (Invert Direct/Reverse Operation) is assigned for an Event
Input Assignment (1 or 2), control will start with the contents set for the
Direct/Reverse Operation parameter inverted when the event input turns
ON, and with the contents left according to the setting when the event
input turns OFF. For details on event inputs and control combined with the
Direct/Reverse Operation parameter, refer to Control by Inverting Direct/
Reverse Operation on page 103.
When heating/cooling control is selected, the Dead Band and Cooling
Coefficient parameters can be used.
96
Dead Band For heating/cooling control, the dead band is set with the set point as its
center. The dead band width is the set value of the Dead Band parameter
(adjustment level). Setting a negative value produces an overlapping
band.
If an overlapping band is set, the bumpless function may not operate
when switching between manual operation and automatic operation.
The default is 0.0 EU for Controllers with Thermocouple/Resistance Ther-
mometer Universal Inputs and 0.00% FS for Controllers with Analog
Inputs.
Dead band: Dead band Overlapping dead band: Dead
Output width = A positive value Output band width = A negative value
Heating Cooling Heating Cooling

side side side side
PV PV
0 0
Set point Set point
Cooling Coefficient If the heating characteristics and cooling characteristics of the control object
are very different and good control characteristics cannot be achieved with the
same PID constants, the cooling coefficient can be used to adjust the propor-
tional band (P) for the control output assigned to the cooling side. Use this to
achieve balanced control between the heating side and cooling side. The pro-
portional bands (P) for the control outputs assigned to the heating/cooling
sides can be calculated using the following equations.
P for control output assigned to heating side = P
P for control output assigned to cooling side = P for control output assigned to
heating side cooling coefficient
The cooling coefficient is multiplied by the P for the control output assigned to
the heating side to obtain control with characteristics that differ from those of
the control output assigned to the heating side.
Output Output
P for control output
P for control output assigned to heat-
assigned to heating side 1.0
ing side 1.0
P for control output P for control output P for control output P for control output
assigned to heating side assigned to cooling side assigned to heating side assigned to cooling side
PV PV
0 0
Set point Set point
P for control output assigned to P for control output assigned to
heating side 0.8 heating side 1.5
Automatic Cooling By executing AT during heating/cooling control, the cooling coefficient can be
Coefficient Adjustment automatically calculated along with the PID parameters.
Parameter name Setting rage Default
Automatic Cooling OFF: Disabled, ON: Enabled OFF
Coefficient Adjust-
ment
Note If there is strong non-linear gain for the cooling characteristics, such as when
cooling water boils for cooling control, it may not be possible to obtain the opti-
mum cooling coefficient at the Controller, and control may take the form of
97
oscillating waves. If that occurs, increase the proportional band or the cooling
coefficient to improve control.
4-4-2 Settings
To set heating/cooling control, set the Standard or Heating/Cooling, Dead
Band, and Cooling Coefficient parameters.
Setting Heating/Cooling Control

Operating Procedure Standard or heating/cooling = Heating/cooling
Standard or
s-hc Heating/
Cooling
stnd
2. Select heating/cooling control in the initial setting level.
stnd: Standard control
h-c: Heating/cooling control
Setting the Cooling Coefficient

Operating Procedure Cooling Coefficient = 10
Adjustment Level 1. Select the Cooling Coefficient parameter in the adjustment level.
Cooling
c-sc Coefficient
1.00
2. Use the U Key to set the parameter to 10.00.
c-sc
10.00
Setting the Dead Band

Operating Procedure Dead Band = 5
Adjustment Level 1. Select the Dead Band parameter in the adjustment level.
C Dead Band
c-db
0.0
C 2. Use the U Key to set the parameter to 5.0.
c-db
5.0
98
Using Event Inputs Section 4-5
4-5 Using Event Inputs

4-5-1 Event Input Settings
Event inputs can be used for Multi-SP, RUN/STOP, Auto/Manual Switch,
Program Start, Invert Direct/Reverse Operation, 100% AT Execute/Can-
cel, 40% AT Execute/Cancel, Setting Change Enable/Disable, and Alarm
Latch Cancel.
Of these, only the number of event inputs (0 to 2) set in the Number of
Multi-SP Uses parameter (initial setting level) are used for the multi-SP
function.
Of these, only the number of event inputs (0 to 2) set in the Number of
Multi-SP Uses parameter (initial setting level) are automatically assigned
by the multi-SP function. Displays for event input assignments will not be
displayed for inputs that are automatically assigned by the multi-SP func-
tion. Event inputs 1 and 2 are used for the multi-SP function by models
with four event inputs.
Event inputs can be used on the following models:
E5CN-@M@-500 with the E53-CN@B@N2 for the E5CN
E5AN/EN-@M@-500-N with the E53-AKB for the E5AN/EN
When using event inputs to switch the multi-SP, the event input assign-
ment display will not appear. Whether the set value and event input
assignments 1 and 2 will be displayed or hidden is shown in the tables
below.
Do not connect the contacts from the same switch to more than one
E5@N Controllers.
Models with Two Event Inputs, 1 and 2
Event input assignment 1 Event input assignment 2 Description of EV1 and EV2
operation
Number of Multi- 0 Displayed (Multi-SP not used). EV1 and EV2 will perform the
SP Uses operation command assigned
using the Event Input Assign-
ment 1 and 2 parameters.
1 Not displayed (Operation per- Displayed (Event input 2 not EV1 will be used for the Multi-
formed with two Multi-SP used as multi-SP switch). SP function to switch between
points.) set points 0 and 1. EV2 will
perform the operation com-
mand assigned using the
Event Input Assignment 2
parameter.
2 Not displayed (Operation performed with four Multi-SP points.) EV1 and EV2 will be used for
the Multi-SP function to switch
between set points 0, 1, 2,
and 3.
99

operation
Number of Multi- 0 Displayed (Multi-SP not used). EV3 and EV4 will perform the
SP Uses operation command assigned
parameter.
and 3.
Models with Four Event Inputs, 1 to 4

Event input Event input Event input Event input Description of EV1, EV2,
assignment 1 assignment 2 assignment 3 assignment 4 EV3, and EV4 operation
Number of Multi- 0 Displayed (Multi-SP not used). EV1, EV2, EV3, and EV4 will
SP Uses perform the operation com-
Event Input Assignment 1, 2,
3, and 4 parameters.
1 Not displayed Displayed (Event inputs 2, 3, and 4 cannot be EV1 will be used for the Multi-
(Operation used for multi-SP switching.) SP function to switch between
performed set points 0 and 1. EV2, EV3,
with two Multi- and EV4 will perform the
SP points.) operation command assigned
ment 2, 3, and parameters.
2 Not displayed (Operation per- Displayed (Event inputs 3 and EV1 and EV2 will be used for
formed with four Multi-SP 4 cannot be used for multi-SP the Multi-SP function to switch
points.) switching.) between set points 0, 1, 2,
and 3. EV3 and EV4 will per-
form the operation command
assigned using the Event
Input Assignment 3 and 4
parameters.
100
Two set points are set externally by using the Number of Multi-SP Uses
parameter.
Switching is possible between two set points (0 and 1) by setting the
Number of Multi-SP Uses parameter to 1. The default setting is 1 and
does not need to be changed to switch between two set points. Set points
0 and 1 are specified by the status of event input 1.
E5CN E5AN/EN
11 11 EV1
EV1 + EV1
12 EV1 12 EV2
+ +
13 EV2 EV2 EV2
13
+
E53-CN@B@N2 in the E53-AKB in the E5AN/EN-@M@-500-N

E5CN-@M@-500 (for E5CN) (for E5AN/EN)
E5GN
7
EV1
8 EV1
+
9 EV2 EV2
+
4-5-2 How to Use the Multi-SP Function

The multi-SP function allows you to set up to four set points (SP 0 to 3) in the
adjustment level. The set point can be switched by operating the keys on the
front panel or by using external input signals (event inputs).
Using Event Inputs

Two Event Inputs: Event Inputs 1 and 2
The following tables show the relationship between the ON/OFF combinations
of event inputs 1 and 2 and the selected set points.
Number of Multi-SP Uses = 1
Event input 1 Selected set point
OFF Set point 0
ON Set point 1
Number of Multi-SP Uses = 2

Event input 1 Event input 2 Selected set point
OFF OFF Set point 0
ON OFF Set point 1
OFF ON Set point 2
ON ON Set point 3
Using Key Operations You can select any of the set points 0 to 3 by changing the set value of the
Multi-SP Uses parameter. The Multi-SP Uses parameter display conditions
are as follows:
If the Controller does not support event inputs, the Multi-SP Uses param-
eter must be set to ON.
If the Controller supports event inputs, the Number of Multi-SP Uses
parameter must be set to 0 and the Multi-SP Uses parameter must be set
to ON.
101
The following table shows the relationship between the Multi-SP Uses param-
eter set value and the selected set point.
Multi-SP Selected set point
0 Set point 0
1 Set point 1
2 Set point 2
3 Set point 3
Note The set point can also be switched using communications.
4-5-3 Settings
Switching between Set Points 0, 1, 2, and 3
Operating Procedure The following example sets the Number of Multi-SP Uses parameter to 2.
25
100
Number of Multi-SP Uses Setting 2. Select the Number of Multi-SP Uses parameter by pressing the M Key.
Number of
ev-m Multi-SP Uses
1
3. Use the U Key to set the parameter to 2.
ev-m
2
Set points 0, 1, 2 and 3 will be set according to the ON/OFF states of event
inputs 1 and 2.
E5CN E5AN/EN E5GN
11 11 EV1 7
EV1 + EV1 EV1
12 EV1 12 EV2 8 EV1
+ + +
13 EV2 EV2 EV2 9 EV2 EV2
13
+ +
4-5-4 Operation Commands Other than Multi-SP

The following table shows the functions assigned when an Event Input
Assignment (1 or 2) is displayed.
Setting Function
none None
stop RUN/STOP
manu Auto/Manual
prst Program Start (See note 1.)
drs Invert Direct/Reverse Operation
at-2 100% AT Execute/Cancel
at-1 40% AT Execute/Cancel (See note 2.)
wtpt Setting Change Enable/Disable
lat Alarm Latch Cancel
102
Note (1) PRST (Program Start) can be set even when the Program Pattern param-
eter is set to OFF, but the function will be disabled.
(2) This function can be set for heating/cooling control, but the function will
be disabled.
When any of the following functions is set for an Event Input Assignment
parameter, the same function cannot be set for another Event Input Assign-
ment parameter: STOP (RUN/STOP), MANU (Auto/Manual Switch), PRST
(Program Start), DRS (Invert Direct/Reverse Operation), AT-2 (100% AT Exe-
cute/Cancel), AT-1 (40% AT Execute/Cancel), WTPT (Setting Change Enable/
Disable), or LAT (Alarm Latch Cancel). Turn event inputs ON and OFF while
the power is being supplied. Event input ON/OFF changes are detected for
inputs of 50 ms or longer. (However, inputs of 250 ms or longer is determined
using logic operations.)
The functions are described in detail below. Event inputs 1 and 2 are taken as
examples.
Executing Run/Stop When the Event Input Assignment 1 or Event Input Assignment 2 parameter
Control is set to STOP (RUN/STOP), control is started when event input 1 or 2 turns
OFF. Control is stopped when the input turns ON. Alarm outputs, however, will
be according to the process value.
The STOP indicator will light while control is stopped.
Setting Input contact Status
Event input 1 or 2 ON STOP
Event input 1 or 2 OFF RUN
Switching between When the Event Input Assignment 1 or Event Input Assignment 2 parameter
Auto and Manual is set to MANU (auto/manual), manual control will start when event input 1 or
Control 2 turns ON. Auto control will start when the input turns OFF.
The MANU indicator will light during manual control.
Event input 1 or 2 OFF Automatic
Event input 1 or 2 ON Manual
Controlling the Start When the Event Input Assignment 1 or Event Input Assignment 2 parameter
of the Simple is set to PRST (program start), the program will start when event input 1 or 2
Program Function turns ON. The program will be reset when the input turns OFF and the RUN/
STOP status will automatically switch to STOP mode. If the program END out-
put is ON, the program END output will turn OFF.
Event input 1 or 2 OFF Reset
Event input 1 or 2 ON Start
Control by Inverting When DRS (Invert Direct/Reverse Operation) is set for the Event Input
Direct/Reverse Assignment 1 or Event Input Assignment 2 parameter and the Direct/Reverse
Operation Operation parameter is set for reverse operation, control starts with direct
operation (cooling control) when event input 1 or 2 turns ON and control starts
with reverse operation (heating control) when the event input turns OFF.
Setting Input Direct/Reverse Operation Status
contact parameter
Event input OFF Direct operation (cooling) Direct operation (cooling)
1 or 2 Reverse operation (heating) Reverse operation (heating)
103
Setting the SP Upper and Lower Limit Values Section 4-6
Setting Input Direct/Reverse Operation Status

contact parameter
Event input ON Direct operation (cooling) Reverse operation (heating)
1 or 2 Reverse operation (heating) Direct operation (cooling)
Switching 100% AT When AT-2 (100% AT Execute/Cancel) is set for either the Event Input Assign-
Execute/Cancel ment 1 or Event Input Assignment 2 parameter, 100% AT will be executed
when event input 1 or 2 turns ON and will be cancelled when the input turns
OFF.
Event input 1 or 2 OFF 100% AT cancelled
Event input 1 or 2 ON 100% AT executed
Switching 40% AT When AT-1 (40% AT Execute/Cancel) is set for either the Event Input Assign-
Execute/Cancel ment 1 or Event Input Assignment 2 parameter, 40% AT will be executed
when event input 1 or 2 turns ON and will be cancelled when the input turns
OFF.
Event input 1 or 2 OFF 40% AT cancelled
Event input 1 or 2 ON 40% AT executed
Switching Setting When WTPT (Setting Change Enable/Disable) is set for either the Event Input
Change Enable/ Assignment 1 or Event Input Assignment 2 parameter, the setting change will
Disable be disabled when event input 1 or 2 turns ON and will be enabled when the
input turns OFF.
Event input 1 or 2 OFF Enabled
Event input 1 or 2 ON Disabled
Switching Alarm When LAT (Alarm Latch Cancel) is set for either the Event Input Assignment 1
Latch Cancel or Event Input Assignment 2 parameter, all alarm latches (alarms 1 to 3,
heater burnout, HS alarm, and heater overcurrent latch) will be cancelled
when event input 1 or 2 turns ON.
Event input 1 or 2 OFF ---
Event input 1 or 2 ON Cancelled
Parameters
ev-1 Event Input Assignment 1: Initial setting level Function of
ev-2 Event Input Assignment 2: Initial setting level event input func-
tion
ev-m Number of Multi-SP Uses: Initial setting level
4-6 Setting the SP Upper and Lower Limit Values

4-6-1 Set Point Limiter
The setting range of the set point is limited by the set point limiter. This func-
tion can be used to prevent setting incorrect process values. The set point lim-
iter is used to prevent the control target from reaching abnormal
temperatures. If the set point is not within the range set for the set point limiter
as the result of changes to the Set Point Upper Limit or Set Point Lower Limit
parameter, the set point will automatically be change to a value within the set
104
Setting the SP Upper and Lower Limit Values Section 4-6
range. The upper- and lower-limit values of the set point limiter are set using
the Set Point Upper Limit and Set Point Lower Limit parameters in the initial
setting level. When the set point limiter is reset, the set point is forcibly
changed to the upper- or lower-limit value of the set point limiter if the set point
is out of the limiter range. Also, when the input type and the temperature unit,
scaling upper-limit value, or lower-limit value are changed, the set point limiter
is forcibly reset to the input setting range or the scaling upper- or lower-limit
value.
Input setting range
Set point limiter

Setting range Set point
A B
Upper limit (Cannot be set.)
value changed
Upper limit value changed Set point
C
Input type changed Set point
Set value Upper/lower limit values B
Sensor upper/lower limit values (Can be set.)
Parameters
sl-h Set Point Upper Limit: Initial setting level To limit the SP setting
sl-l Set Point Lower Limit: Initial setting level To limit the SP setting
4-6-2 Setting
Set the set point upper and lower limits in the Set Point Upper Limit and Set
Point Lower Limit parameters in the initial setting level. In this example, it is
assumed that the input type is set to a K thermocouple with a temperature
range of 200 to 1300C.
200 1300
Input setting range
Set point limiter
100 1000
Setting the Set Point Upper-limit Value

Operating Procedure Set Point Upper Limit = 1000
Input Type 1. Press the O Key for at least three seconds to move from the operation
in-t level to the initial setting level.
5
C Set Point 2. Select the Set Point Upper Limit parameter.
sl-h Upper-limit
1300
105
Using the SP Ramp Function to Limit the SP Change Rate Section 4-7
C 3. Use the U and D Keys to set the parameter to 1000.

sl-h
1000
Setting the Set Point Lower-limit Value

Operating Procedure Set Point Lower Limit = 100
C Set Point 1. Select the Set Point Lower Limit parameter in the initial setting level.
sl-l Lower Limit
-200
C 2. Use the U and D Keys to set the parameter to 100.
sl-l
-100
4-7 Using the SP Ramp Function to Limit the SP Change Rate

4-7-1 SP Ramp
The SP ramp function is used to restrict the width of changes in the set point
as a rate of change. When the SP ramp function is enabled and the change
width exceeds the specified rate of change, an area where the set point is
restricted will be created, as shown in the following diagram.
During the SP ramp, control will be performed not for the specified set point
but rather for the set point restricted by the rate of change set for the SP ramp
function.
SP
SP ramp
SP after change
SP ramp
set value
SP ramp time unit (s/min)
SP before change
Time
Point of change
The rate of change during SP ramp is specified using the SP Ramp Set Value
and SP Ramp Time Unit parameters. The SP Ramp Set Value parameter is
set to OFF by default, i.e., the SP ramp function is disabled.
Changes in the ramp set point can be monitored in the Set Point During SP
Ramp parameter (operation level). Use this parameter when monitoring SP
ramp operation.
The SP ramp function operates in the same way when switching the set point
using the multi-SP function.
106
Using the SP Ramp Function to Limit the SP Change Rate Section 4-7
Parameters
ol-h MV Upper Limit: Adjustment level To limit the manipulated variable
ol-l MV Lower Limit: Adjustment level To limit the manipulated variable
sl-h Set Point Upper Limit: Initial setting level To limit the SP setting
sl-l Set Point Lower Limit: Initial setting level To limit the SP setting
sprt SP Ramp Set Value: Adjustment level To limit the SP rate of change
spru SP Ramp Time Unit: Advanced function setting level Unit for setting the SP
alsp Alarm SP Selection: Advanced function setting level Alarm SP selection
Operation at Startup If the SP ramp function is enabled when the Controller is turned ON or when
switching from STOP to RUN mode, the process value reaches the set point
using the SP ramp function in the same way as when the set point is changed.
In this case, operation is carried out with the process value treated as the set
point before the change was made. The direction of the SP ramp changes
according to the relationship between the process value and the set point.
PV < SP PV > SP
SP SP
SP ramp
SP ramp
Set point PV
Same rate
of change
Set point
PV
Time Time
Power ON Power ON
Restrictions during Execution of auto-tuning starts after the end of the SP ramp.
SP Ramp Operation When control is stopped or an error occurs, the SP ramp function is dis-
abled.
107
Moving to the Advanced Function Setting Level Section 4-8
Alarms during SP The operation of alarms during SP ramp operation depends on whether
Ramp Operation alarms are set to be based on the ramp set point or the target set point (refer
to the following diagrams). The set point to be used is set in the Alarm SP
Selection parameter. (Refer to page 244.)
Alarm SP Selection = Ramp SP (Alarm Type: 1 (Upper/Lower Limits))
Temperature
Alarm output ON
Alarm output ON
Time
Alarm SP Selection = Target SP (Alarm Type: 1 (Upper/Lower Limits))

Temperature
Alarm output ON
Alarm output ON
Time
4-8 Moving to the Advanced Function Setting Level

To move to the advanced function setting level, you must first cancel the pro-
tection applied by the Initial Setting/Communications Protect parameter.
In the default setting, the advanced function setting level is protected and you
cannot move to this setting level.
1,2,3... 1. Press the O and M Keys simultaneously for at least three seconds in op-
eration level.
Note The key pressing time can be changed in the Move to Protect Level
Time parameter (advanced function setting level).
Protect Level 2. The Controller moves to the protect level, and the Operation/Adjustment
Operation/Adjust- Protect parameter is displayed.
oapt ment Protect
0
Initial Setting/ 3. Press the M Key once to move to the Initial Setting/Communications Pro-
icpt Communica-
tions Protect
tect parameter.
1
4. Set the set value to 0.
icpt
0
108
Moving to the Advanced Function Setting Level Section 4-8
Operation Level 5. Press the O and M Keys simultaneously for at least one second to re-
C PV/SP turn to the operation level.
25
100
Initial Setting Level 6. Move to the advanced function setting level.
Input Type Press the O Key for at least three seconds to move from the operation
in-t level to the initial setting level.
5
Move to Ad- ing the M Key.
Setting Level
-169
Advanced function setting level 8. Press the D Key, enter the password (169), and then either press the
Parameter M Key or leave the setting for at least two seconds to move to the ad-
init Initialization vanced function setting level from the initial setting level.
off
Initial Setting Level 9. To return to the initial setting level, press the O Key for at least one sec-
Input Type ond.
in-t
5
C PV/SP
25
100
109
Using the Key Protect Level Section 4-9
4-9 Using the Key Protect Level

4-9-1 Protection
To move to the protect level, press the O and M Keys simultaneously for
at least three seconds in operation level or adjustment level. (See note.)
Note The key pressing time can be changed in the Move to Protect Level
Time parameter (advanced function setting level).
The protect level protects parameters that are not changed during Con-
troller operation until operation is started to prevent them from being mod-
ified unintentionally.
There are four types of protection: operation/adjustment protect, initial
setting/communications protect, setting change protect, and PF Key pro-
tect.
The protect level settings restrict the range of parameters that can be
used.
Operation/Adjustment The following table shows the relationship between set values and the range
Protect of protection.
Level Set value
oapt 0 1 2 3
0 Operation PV Can be dis- Can be dis- Can be dis- Can be dis-
level played played played played
PV/SP Can be dis- Can be dis- Can be dis- Can be dis-
played and played and played and played
changed changed changed
Others Can be dis- Can be dis- Cannot be Cannot be
played and played and displayed and displayed and
changed changed moving to moving to
other levels is other levels is
not possible not possible
Adjustment level Can be dis- Cannot be Cannot be Cannot be
played and displayed and displayed and displayed and
changed moving to moving to moving to
other levels is other levels is other levels is
not possible not possible not possible
Parameters are not protected when the set value is set to 0.

The default is 0.
Initial Setting/ This protect level restricts movement to the initial setting level, communica-
Communications tions setting level, and advanced function setting level.
Protect Set Initial setting level Communications Advanced function
value setting level setting level
icpt 0 Possible to reach Possible to reach Possible to reach
1 1 Possible to reach Possible to reach Not possible to reach
2 Not possible to reach Not possible to reach Not possible to reach
The default is 1.
Setting Change This protect level restricts key operations.

Protect Set value Description
OFF Settings can be changed using key operations.
wtpt ON Settings cannot be changed using key operations. (The protect level
off settings, however, can be changed.)
110
The default is OFF.

The all protect indication ( ) will light when setting change protect is
set.
PF Key Protect This protect level enables or disables PF Key operations.

Set value Description
pfpt OFF PF Key enabled.
off ON PF Key disabled (Operation as function key prohibited).
The default is OFF.
4-9-2 Entering the Password to Move to the Protect Level

Protect level can be moved to only by display the password display and
entering the correct password. (The user can set any password in the
Protect Level Password parameter. If no password is set (i.e., if the pass-
word is set to 0 in the Protect Level Password parameter), the password
input display to move to protect level will not be displayed and the protect
level can be moved to directly.
Operating Procedure Use the following procedure to move to protect level.
Example with a Password of 1234

Operation Level
C PV/SP
25
100
Protect Level 1. Press the O and M Keys simultaneously for at least the time set in the
Move to Protect Move to Protect Level Time parameter to move from the operation level
pmov Level to the protect level.
0
2. Press the U Key to set the parameter to 1234 (password input).
pmov
1234
Protect Level 3. Move to the Operation/Adjustment Protect parameter by pressing the O
Operation/Adjust- or M Key or leaving the setting for at least two seconds.
oapt ment Protect
0
Example with No Password Set

Operation Level
C PV/SP
25
100
Protect Level Press the O and M Keys simultaneously for at least the time set in the
Operation/Adjust- Operation/Adjustment Protect parameter to move from the operation level to
oapt ment Protect the protect level.
When a password is not set, the Operation/Adjustment Protect parameter
0 will be displayed.
111
Setting the Password

Operating Procedure Use the following procedure to set the password to move to the protect level.
Example To set the Password to 1234

Operation Level
C PV/SP
25
100
Protect Level 1. Press the O and M Keys simultaneously for at least the time set in the
Operation/Adjust- Move to Protect Level Time parameter to move from the operation level
oapt ment Protect to the protect level.
0
Protect Level 2. Select the Password to Move to Protect Level parameter by pressing the
Password to M Key.
prlp Move
Level
to Protect
0
3. Press the O and U Keys to set the parameter to 1234.
prlp (To prevent setting the password incorrectly, the U and O Keys or D
and O Keys must be pressed simultaneously to set the password.)
1234
Note Protection cannot be cleared or changed without the password. Be
careful not to forget it. If you forget the password, contact your
OMRON sales representative.
Communications The Write Variable operation command can be used via communications
Operation Command to write the password to the Move to Protect Level parameter. When the
to Move to the Protect correct password is written, the display will change to the Operation/
Level Adjustment Protect parameter and writing the parameters in the protect
level will be enabled.
Note (1) If the Write Variable operation command is used to write the wrong pass-
word to the Move to Protect Level parameter after the correct parameter
has been written, the Move to Protect Level parameter will be displayed
and any Write Variable operation commands to write parameters in the
protect level will result in operation errors.
(2) If a password is not set or if it is set to 0, the display will change to the
Operation/Adjustment Protect parameter and writing the parameters in
the protect level will be enabled immediately.
112
PV Change Color Section 4-10
4-10 PV Change Color

4-10-1 PV Color Change Function
Use the PV color change function to change the color of the PV display (No. 1
display).
There are three display colors, orange, red, and green, and you can select
from the following three modes and eight functions.
PV Change Constant: This mode displays orange, red, or green all the time.
colr Color Linked to Alarm 1: This mode switches the PV display color from red to
green when alarm 1 turns ON or from green to red when alarm 1 turns
ON.
Linked to PV stable band: This mode switches the PV display color
between red outside the PV stable band and green within PV stable band,
or between green outside the PV stable band and red within PV stable
band.
Set the PV stable band in the PV Stable Band parameter (advanced func-
tion setting level).
The default is red (red).
The following tables shows the display functions that can be set using the PV
color change function.
Mode Setting Function PV change color Application example
Constant org Orange Constant: Orange To match the display color
with other Controller models
red Red Constant: Red To match the display color
grn Green Constant: Green To match the display color
Linked to Alarm
alarm 1 value
ALM1 lit
PV
SP
ALM1 not lit ALM1 lit Application example

r-g Red to Green Red Green To display the PV reached sig-
nal
g-r Green to Red Green Red To display error signals
Linked to PV PV
PV stable stable stable
band band band
Low Within High

PV
SP
Low Within PV stable High Application example

band
r-g.r Red to Green to Red Green Red To display stable status
Red
g-o.r Green to Green Orange Red To display stable status
Orange to Red
o-g.r Orange to Orange Green Red To display stable status
Green to Red
113
PV Stable Band When the mode to link to the PV stable band is selected, the PV display color
PV Stable will change according to whether the present value (PV) is lower than, within,
pv-b Band or higher than the PV stable band shown in the following figure. The PV stable
band is set with the SP as the center, as shown below.
PV stable PV stable
band band
Low Within High

PV
SP
The default is 5.0 (C/F) for Controllers with Thermocouple/Resistance Ther-

mometer Universal Inputs and 5.00% FS for Controllers with Analog Inputs.
4-10-2 Setting
Setting the PV To display the PV in a stable green display when the PV is within 15.0C of
Change Color to the set point to enable checking the control process at a glance, set the PV
Indicate Stable Status Change Color and PV Stable Band parameters.
PV change color = r-gr (Red to Green to Red)
PV stable band = 15.0C
Operating Procedure Release the protection before setting the PV Change Color and PV Stable
Band parameters to enable moving to advanced function setting level. (Refer
to steps 1 to 8 on page 108.)
Operation Level
C PV/SP
25
100
in-t
5
Setting Level
3. Use the D Key to enter 169 (the password).
-169
Advanced Function Setting Level Move to the advanced function setting level by pressing the M Key or
Parameter leaving the setting for at least two seconds.
init Initialization
off
Advanced Function Setting Level 4. Select the PV Change Color parameter by pressing the M Key.
PV Change
colr Color
red
114
5. Press the U Key to set the parameter to r-gr.

colr
r-g.r
Advanced Function Setting Level 6. Select the PV Stable Band parameter by pressing the M Key.
C PV Stable
pv-b Band
5.0
C 7. Use the U Key to set the parameter to 15.0.
pv-b
15.0
8. To return to the initial setting level, press the O Key for at least one sec-
ond.
C PV/SP
25
100
115
Alarm Delays Section 4-11
4-11 Alarm Delays

4-11-1 Alarm Delays
Delays can be set for the alarm outputs. ON and OFF delays can be set
separately for alarms 1, 2, and 3. The ON and OFF delays for alarm 1
function only for the alarm function. If the alarm 1 function is set to be out-
put as an OR with other alarms (i.e., the heater burnout alarm, HS alarm,
heater overcurrent alarm, or input error output alarm), delays cannot be
set for the other alarms. The ON and OFF delays for alarms 1, 2, and 3
also apply to the individual SUB1, SUB2, and SUB3 indicators and to
communications status. The alarm ON delays will also function when
power is turned ON or when moving from the initial setting level to opera-
tion level (e.g., to software resets). All outputs will turn OFF and the OFF
delays will not function when moving to the initial setting level or when an
alarm is output for a A/D converter error.
Operation of Alarm ON and OFF Delays (for an Upper-limit Alarm)

PV
Alarm hysteresis
Alarm setting
ON delay
set time
Alarm status OFF delay
set time
Alarm Latch = OFF

ON delay set time
Alarm will not turn ON.
The alarm will not turn ON if the time that the alarm is ON is equal to or
less than the ON delay set time. Also, the alarm will not turn OFF if the
time that the alarm is OFF is equal to or less than the OFF delay set time.
If an alarm turns OFF and then back ON during the ON delay time, the
time will be remeasured from the last time the alarm turns ON. Also, if an
alarm turns ON and then back OFF during the OFF delay time, the time
will be remeasured from the last time the alarm turns OFF.
Parameters Related to Alarm Delays

Parameter name Symbol Set (monitor) values
Alarm 1 ON Delay a1on 0 to 999 (s)
Alarm 1 OFF Delay a1of 0 to 999 (s)
116
Alarm Delays Section 4-11
Note (1) The defaults are 0, i.e., the ON and OFF delays are disabled.
(2) The parameters are displayed when alarm functions are assigned and
when the alarm type is set to any type but 0 (none), 12: LBA, or 13: PV
change rate alarm.
Operating Procedure Use the following procedure to set ON and OFF delays for the alarm 1.
An ON delay of 5 seconds and an OFF delay of 10 s will be set.
Operation Level
C PV/SP
25
100
in-t
5
Move to Ad- ing the M Key. (For details on moving between levels, refer to 4-8 Moving
amov Setting Level
vanced Function to the Advanced Function Setting Level.)
0
Advanced Function Setting Level 3. Press the D Key to enter the password (169) and move from the initial
init Initialization
off
Advanced Function Setting Level 4. Press the M Key to select the Alarm 1 ON Delay parameter.
Alarm 1 ON
a1on Delay
0
5. Press the U Key to set the parameter to 5.
a1on
5
Advanced Function Setting Level 6. Press the M Key to select the Alarm 1 OFF Delay parameter.
Alarm 1 OFF
a1of Delay
0
7. Press the U Key to set the parameter to 10.
a1of
10
in-t
5
117
Loop Burnout Alarm Section 4-12
25
100
4-12 Loop Burnout Alarm

4-12-1 Loop Burnout Alarm (LBA)
With a loop burnout alarm, there is assumed to be an error in the control
loop if the control deviation (SP PV) is greater than the threshold set in
the LBA Level parameter and if the control deviation is not reduced by at
least the value set in the LBA Detection Band parameter within the LBA
detection time.
Loop burnout alarms are detected at the following times.
LBA level
Set point
LBA level
LBA band LBA band
LBA band
LBA detec-
Area where LBA LBA detection LBA detection
tion time LBA detection time
is not detected time
time
(2) (3) (4) (5) (6) (7)

(1) LBA OFF LBA ON LBA OFF LBA ON
If the control deviation is reduced in the area between 1 and 2 (i.e., the set
point is approached) and the amount the control deviation is reduced is at
least equal to the LBA band, the loop burnout alarm will remain OFF.
The process value is within the LBA level between 3 and 4, and thus loop
burnout alarms will not be detected. (The loop burnout alarm will remain OFF.)
If the process value is outside the LBA level between 4 and 5 and the control
deviation is not reduced by at least the LBA band within the LBA detection
time, the loop burnout alarm will turn ON.
point is approached) and the amount the control deviation is reduced is at
least equal to the LBA band, the loop burnout alarm will turn OFF.
point is approached) and the amount the control deviation is reduced is less
than the LBA band, the loop burnout alarm will turn ON.
If the LBA detection time, LBA level, LBA detection band, and PID set-
tings are not appropriate, alarms may be detected inappropriately or
alarms may not be output when necessary.
Loop burnout alarms may be detected if unexpectedly large disturbances
occur continuously and a large deviation does not decrease.
If a loop burnout occurs when the set point is near the ambient tempera-
ture, the temperature deviation in a steady state may be less than the LBA
level, preventing detection of the loop burnout.
118
If the set point is so high or low that it cannot be reached even with a sat-
urated manipulated variable, a temperature deviation may remain even in
a steady state and a loop burnout may be detected.
Detection is not possible if a fault occurs that causes an increase in tem-
perature while control is being applied to increase the temperature (e.g.,
an SSR short-circuit fault).
Detection is not possible if a fault occurs that causes a decrease in tem-
perature while control is being applied to decrease the temperature (e.g.,
a heater burnout fault).
Parameters Related to Loop Burnout Alarms

Parameter name Symbol Setting range Remarks
LBA Detection Time lba 0 to 9999 (s) Setting 0 disables the LBA
function.
LBA Level lbal Controllers with Thermo- 0.1 to 999.9 (C/F) (See Default: 8.0 (C/F)
couple/Resistance Ther- note.)
mometer Universal Inputs
Controllers with Analog 0.01 to 99.99 (%FS) Default: 10.00% FS
Inputs
LBA Band lbab Controllers with Thermo- 0.0 to 999.9 (C/F) (See Default: 3.0 (C/F)
couple/Resistance Ther- note.)
mometer Universal Inputs
Controllers with Analog 0.00 to 99.99 (%FS) Default: 0.20% FS
Inputs
Note Set None as the unit for analog inputs.

A loop burnout alarm can be output by setting the alarm 1 type to 12
(LBA).
A setting of 12 (LBA) can be set for alarm 2 or alarm 3, but the setting will
be disabled.
Loop burnouts are not detected during SP ramp operation.
Loop burnouts are not detected during auto-tuning, manual operation, or
while stopped.
If the alarm 1 latch is set to ON, the latch will be effective for the loop
burnout alarm.
Automatically Setting The LBA detection time is automatically set by auto-tuning.

the LBA Detection (It is not set automatically, however, for heating/cooling control.)
Time If the optimum LBA detection time is not obtained by auto-tuning, set the
LBA Detection Time parameter (advanced function setting level).
119
Determining the LBA To manually set the LBA detection time, set the LBA Detection Time
Detection Time parameter to twice the LBA reference time given below.
1,2,3... 1. Set the output to the maximum value.

2. Measure the time required for the width of change in the input to reach the
LBA band.
Measurement time
Temperature Tm
PV
LBA band
MV = 100%
Time
LBA detection time = Tm 2
3. Set the LBA Detection Time parameter to two times the measured time.
LBA Level Set the control deviation when the control loop is working properly.
Inputs.
LBA Band There is assumed to be an error in the control loop if the control deviation
is greater than the threshold set in the LBA Level parameter and if the
control deviation does not change by at least the value set in the LBA
Band parameter.
Inputs.
Operating Procedure Perform the following procedure to use the loop burnout alarm.
In this example, the LBA detection time is set to 10, the LBA level is set to 8.0,
and the LBA band is set to 3.0.
Operation Level
C PV/SP
25
100
in-t
5
Initial Setting Level 2. Select the Alarm 1 Type parameter by pressing the M Key.
Alarm 1 Type
alt1
2
120
Initial Setting Level 3. Press the U Key to set the parameter to 12.
alt1
12
Setting Level
ing the M Key. (For details on moving between levels, refer to 4-8 Moving
to the Advanced Function Setting Level.)
0
init Initialization
off
Advanced Function Setting Level 6. Select the LBA Detection Time parameter by pressing the M Key.
LBA Detection
lba Time
0
C 7. Press the U Key to set the parameter to 10.
lba
10
Advanced Function Setting Level 8. Select the LBA Level parameter by pressing the M Key.
C LBA Level
lbal
8.0
C 9. Press the U Key to set the parameter to 8.0. (The default is 8.0.)
lbal
8.0
Advanced Function Setting Level 10. Select the LBA Band parameter by pressing the M Key.
C LBA Band
lbab
3.0
C 11. Press the U or D Key to set the parameter to 3.0. (The default is 3.0.)
lbab
3.0
in-t
5
25
100
121
Performing Manual Control Section 4-13
4-13 Performing Manual Control

4-13-1 Manual Operation
The manipulated variable can be set in manual mode if the PV/MV param-
eter is displayed in the manual control level. The final MV used in auto-
matic mode will be used as the initial manual MV when moving from
automatic mode to manual mode. In manual mode, the change value will
be saved immediately and reflected in the actual MV.
The automatic display return function will not operate in manual mode.
Balanceless-bumpless operation will be performed for the MV when
switching from manual operation to automatic operation. (See note.)
If a power interruption occurs during manual operation, manual operation
will be restarted when power is restored using the same MV as when
power was interrupted.
Switching between automatic and manual operation is possible for a max-
imum of one million times.
Manual operation can be used only for PID control.
Note In balanceless-bumpless operation, the MV before switching is used initially
after the switch and then gradually changed to achieve the proper value after
switch to prevent radical changes in the MV after switching operation.
The overall manual operation is illustrated in the following figure.
MV (%)
Balanceless-bumpless
0 Time
MV switched OFF ON
Manual
Power in-
terrupted
Automatic
Related Displays and Parameters

Parameter name Symbol Level Remarks
PV/MV (Manual MV) --- Manual Control Level 5.0 to 105.0 (heating/cooling control: 105.0 to
105.0 (See note 2.)
Auto/Manual Switch a-m Operation Level Switches between automatic and manual
modes.
Auto/Manual Select Addi- amad Advanced Function Setting Enables switching between automatic and man-
tion Level ual modes.
Note (1) Refer to 4-16 Output Adjustment Functions for information on the priority
for the MV.
(2) For Manual MV Limit Enable, this value will be between the MV upper limit
and the MV lower limit.
122
Manual MV Limit When the Manual MV Limit Enable parameter is set to ON (enabled), the MV
Enable limits will function and the setting range for the Manual MV parameter will be
between the MV upper limit and the MV lower limit. When the parameter is set
to OFF (disabled), MV limits will not function.
Parameter name Setting range Default
Manual MV Limit OFF: Disabled, ON: Enabled ON
Enable
Moving from the When the O Key is pressed for at least 3 seconds in the operation level's
Operation Level to the auto/manual switching display, the manual mode will be entered and the
Manual Control Level manual control level will be displayed. It is not possible to move to any dis-
plays except for the PV/MV parameter during manual operation. Press the
O Key for at least one second from the PV/MV parameter display in man-
ual control level to return to automatic mode and display the top parame-
ter in the operation level.
Operation Level
C
Press O key for at least 1 s. 25 PV
M
C
25 PV/SP
Manual Control Level

100
M
C
25 a-m a-m Auto/Manual Switch
20
Press O key for at least
PV/MV 3 s.
M
a-m display flashes for
at least 1 s.
m-sp Multi-SP
0
M
If an event input is set to MANU (auto/manual), the Auto/Manual Switch

parameter will not be displayed. Use the event input to switch between
automatic and manual modes.
123
Using the PF Key to When the PF Setting parameter is set to A-M (Auto/Manual), pressing the
Move to the Manual PF Key for at least one second while in the adjustment or operation level
Control Level will change the mode to manual mode and move to the manual control
level. During manual operation it is not possible to move to any displays
other than PV/MV (Manual MV). Press the PF Key for at least one second
from the PV/MV display in the manual control mode to change the mode
to automatic mode, move to the operation level, and display the top
parameter in the operation level.
When MANU (Auto/Manual) is selected for an event input, the Auto/Man-
ual Switch parameter is not displayed. In that case, switching between
auto and manual mode is executed by using an event input.
Auto/Manual Select The Auto/Manual Select Addition parameter must be set to ON in the
Addition advanced function setting level before it is possible to move to manual
mode. The default is OFF.
Note (1) Priority of Manual MV and Other Functions

Even when operation is stopped, the manual MV is given priority.
Auto-tuning and self-tuning will stop when manual mode is entered.
(2) Manual MV and SP Ramp
If operating, the SP ramp function will continue even when manual mode
is entered.
Operating Procedure Use the following procedure to set the manipulated variable in manual mode.
Operation Level
C PV/SP
25
100
in-t
5
2. Press the M Key to select PID-ON/OFF and then select PID with the U
cntl Key.
pid
amov Setting Level
0
init Initialization
off
Advanced Function Setting Level 5. Select the Auto/Manual Select Addition parameter by pressing the M
Auto/Manual Key.
amad Select Addition
off
124
6. Use the U Key to set the parameter to ON.

amad
on
in-t
5
8. Press the O Key for at least one second to move from the initial setting
level to the operation level.
Operation Level 9. Select the Auto/Manual Switch parameter by pressing the M Key.
Auto/Manual
a-m Switch
Manual Control Level 10. Press the O Key for at least three seconds to move from the operation
C PV/MV level to the manual control level.
25
0.0
C 11. Press the U or D Key to set the manual MV. (In this example, the MV is
25 set to 50.0%.)
50.0 Note The manual MV setting must be saved (see page 18), but values
changed with Key operations are reflected in the control output
immediately.
Operation Level 12. Press the O Key for at least one second to move from the manual control
C
25 PV/SP

100
Operating Procedure In this example, A-M (Auto/Manual) is set for the PF Setting parameter
(E5AN/EN only).
Operation Level
C
25 PV/SP

100
in-t
5
2. Press the M Key to select PID-ON/OFF and then select PID with the U
cntl Key.
pid
amov Setting Level
0
125
Using the Transfer Output Section 4-14
init Initialization
off
Advanced Function Setting Level 5. Select the Auto/Manual Select Addition parameter by pressing the M
Auto/Manual Key.
amad Select Addition
off
6. Use the U Key to set the parameter to ON.
amad
on
7. Press the M Key to select the PF Setting parameter and confirm that it is
pf set to A-M. (A-M is the default setting.)
a-m
in-t
5
9. Press the O Key for at least one second to move from the initial setting
Manual Control Level 10. Press the PF Key for at least one second to move from the operation level
C PV/MV to the manual control level.
25
0.0
C 11. Press the U or D Key to set the manual MV. (In this example, the MV is
25 set to 50.0%.)
50.0 Note The manual MV setting must be saved (see page 18), but values
changed with key operations are reflected in the control output
immediately.
Operation Level 12. Press the PF Key to move from the manual control level to the operation
C
level.
25 alm

100
4-14 Using the Transfer Output

4-14-1 Transfer Output Function
To use a transfer output, change the setting for the Transfer Type parame-
ter to anything other than OFF. (This will enable the Transfer Output Upper
Limit and Transfer Output Lower Limit parameters.)
126
The operation is shown in the following table.

Control output 1 Control output 2 Transfer output
destination
Current output None, relay output, voltage Control output 1
output (for driving SSR)
Relay output, voltage out- None, relay output, voltage None
put (for driving SSR) output (for driving SSR)
Precision and User Calibration

Precision User calibration
Simple transfer out- Not specified. Not supported.
put
Transfer Output Type

Transfer output type Symbol Setting range
OFF (See note 1.) off ---
Set point sp SP lower limit to SP upper limit
Set point during SP ramp sp-m SP lower limit to SP upper limit
PV pv Input setting range lower limit to input set-
ting range upper limit or
Scaling lower limit to scaling upper limit
MV monitor (heating) mv 5.0 to 105.0 (heating/cooling control: 0.0 to
105.0) (See note 2.)
MV monitor (cooling) c-mv 0.0 to 105.0 (See note 2.)
Note (1) The default is OFF.

(2) The output value will be different between when the Transfer Output Type
parameter is set to a heating control output or cooling control output, and
when the Control Output 1 Assignment parameter is set to a heating con-
trol output or cooling control output.
Example: When a Current Output Is Set to 4 to 20 mA and MV Monitor
(Heating) Is Selected
When used as a transfer output, 4.0 mA will be output for 0% and
20.0 mA will be output for 100%.
When used as a control output, 3.7 mA will be output for 0% and 20.3 mA
will be output for 100% so that the actuator is controlled at 0% or 100%.
Output current (mA)
20.3
Transfer output value
20
Control output
4
3.7
0 MV (%)
100
(The above graph is for when the linear current output type is set to 4 to 20 mA.)
127
Transfer Scaling Reverse scaling is possible by setting the Transfer Output Lower Limit
parameter larger than the Transfer Output Upper Limit parameter. If the
Transfer Output Lower Limit and Transfer Output Upper Limit parameters
are set to the same value when 4 to 20 mA is set, the transfer output will
be output continuously at 0% (4 mA).
If the SP, SP during SP ramp, or PV is selected, the Transfer Output
Lower Limit and Transfer Output Upper Limit parameters will be forcibly
initialized to the respective upper and lower setting limits for changes in
the upper and lower limits of the SP limiter and the temperature unit.
If the MV for heating or MV for cooling is selected, the Transfer Output
Lower Limit and Transfer Output Upper Limit parameters will be initialized
to 100.0 and 0.0, respectively, when a switch is made between standard
control and heating/cooling control using the Standard or Heating/Cooling
parameter.
The output current when the linear current type is set to 4 to 20 mA, the
transfer output upper limit is set to 90.0, and the transfer output lower limit
is set to 10.0 is shown in the following graph.
For scaling from 0.0% to 100.0%, the output for 5.0 to 0.0 will be the
same value as for 0.0%, and the output for 100.0 to 105.0 will be the
same value as for 100.0%
Output current (mA)
20
MV (%)
0 10 90 100
Transfer output Transfer output
lower limit upper limit
(The above graph is for when the linear current output type is set to 4 to 20 mA.)
Operating Procedure The following procedure sets the transfer output for an SP range of 50 to
200.
Operation Level
C PV/SP
25
100
in-t
0
Initial Setting Level 2. Select the Transfer Output Type parameter by pressing the M Key.
Transfer Output
tr-t Type
off
128
Using the Simple Program Function Section 4-15
3. Press the U Key to select sp (set point).

tr-t
sp
Initial Setting Level 4. Select the Transfer Output Upper Limit parameter by pressing the M Key.
C Transfer Output
tr-h Upper Limit
1300
C 5. Use the D Key to set the parameter to 200. The default is 1300.
tr-h
200
Initial Setting Level 6. Select the Transfer Output Lower Limit parameter by pressing the M Key.
C Transfer Output
tr-l Lower Limit
-200
C 7. Use the U Key to set the parameter to 50. The default is 200.
tr-l
-50
C PV/SP
25
100
4-15 Using the Simple Program Function

4-15-1 Simple Program Function
The simple program function can be used for the following type of control.
SP
Wait band
Set point
Wait band
PV
Soak time END display

RSET STRT
END output
Select either
STOP or RUN.
129
The program will start when the Program Start parameter is changed from
RSET to STRT. END will be displayed on the No. 2 display and the output
assigned as the program end output will turn ON after the time set in the
Soak Time parameter has expired in the wait band. The Program Pattern
parameter can be used to select moving to STOP mode or continuing
operation in RUN mode after the program ends.
Parameters Related to the Simple Program Function

Parameter name Symbol Set (monitor) values Unit Display level
Program Pattern ptrn OFF, STOP, CONT --- Initial setting level
Program Start prst RSET, STRT --- Operation level
Soak Time soak 1 to 9999 min or h Adjustment level
Soak Time Unit t-u m (minutes)/h (hours) --- Advanced function set-
ting level
Wait Band wt-b OFF or 0.1 to 999.9 (See note 2.) C or F (See notes 1 Adjustment level
and 2.)
Soak Time Remain sktr 0 to 9999 min or h Operation level
Monitor
Note (1) Set for Controllers with Thermocouple/Resistance Thermometer Univer-

sal Inputs. Set None as the unit for Controllers with Analog Inputs.
(2) The setting unit of the Wait Band parameter is %FS for Controllers with
Analog Inputs and the setting range is OFF or 0.01 to 99.99.
Program Pattern Either of two program patterns can be selected. The simple program opera-
tion will not be performed if the Program Pattern parameter is set to OFF.
Pattern 1 (STOP)
Control will stop and the STOP mode will be entered when the program has
ended.
SP
Wait band
Set point
Wait band
PV
RSET STRT Soak time END display

END output
Automatically switches
from RUN to STOP mode.
Pattern 2 (CONT)
Control will continue in RUN mode when the program has ended.
SP
Set point Wait band

Wait band
PV
RSET STRT Soak time END display

END output
RUN mode continues.
130
Starting Method Any of the following three methods can be used to start the simple program.
Setting the Program Start parameter to STRT.
Turning ON an event input. (The program start must be assigned to an
event input. See note.)
Starting with an Operation Command using communications. (When the
program start is not assigned to an event input.)
Note When the simple program is started and reset, writing is performed to
EEPROM. Be sure to consider the write life (1 million writes) of the EEPROM
in the system design. When the program start is assigned to an event input,
the Program Start parameter will function as a monitor display, and the RSET/
STRT displays can be used to check when the event input has started or reset
the simple program. When this is done, the Program Start parameter func-
tions as a monitor display only and cannot be changed using key operations.
If the Program Pattern parameter is set to OFF, the event input assignment
setting will be initialized to None.
Soak Time and Wait Band

Wait band
Set point
Wait band
PV
RSET STRT
(1) (2) (3) (4) (5)
Soak time
remain
Set point Set point
The wait band is the band within which the process value is stable in respect
to the set point. The soak time is measured within the wait band. The timer
that measures the soak time operates only when the process value is within
the wait band around the set point (i.e., SP wait band). In the following dia-
gram, the timer will be stopped between the start and (1), (2) and (3), and (4)
and (5) and will measure the time only between (1) and (2), (3) and (4), and
(5) and the end.
Note If the wait band is set to OFF, the wait band will be treated as infinity and the
timer will measure time continuously after changing from RSET to STRT.
131
4-15-2 Operation at the Program End

Display at the Program End
When the program ends, the process value will be displayed on the No. 1 dis-
play (see note) and the set point and end will be alternately displayed on the
No. 2 display at 0.5 s intervals.
Note One of the following displays: PV/SP, PV only, or PV/MV.
120.1 Displayed alternately.
end 120.0
Program End Output

The output assignment parameters can be used to assign the program END
output to any output. The program END output can also be used in communi-
cations status.
E5CN/CN-U, E5AN/EN
When the Program Pattern parameter is changed from OFF to STOP or
CONT for the E5CN, E5CN-U, E5AN, or E5EN, the Auxiliary Output 1 Assign-
ment parameter will automatically be set to the END output. When the Pro-
gram Pattern parameter is changed from STOP or CONT to OFF, the Alarm 1
Output Assignment parameter will automatically be initialized to ALM1.
E5GN
When the Program Pattern parameter is changed from OFF to STOP or
CONT for the E5GN, the Auxiliary Output 1 Assignment parameter will auto-
matically be set to the END output. When the Program Pattern parameter is
changed from STOP or CONT to OFF, the Alarm 1 Output Assignment param-
eter will automatically be initialized to ALM1. When using heating/cooling con-
trol and the Program Pattern parameter is changed from OFF to STOP or
CONT, the END output will not be assigned to an output. Use the output
assignment parameters to assign the program END output to the desired out-
put.
Clearing the Program End Status
The program END output and display will be cleared when the Program Start
parameter is changed from STRT to RSET. The setting is changed from STRT
to RSET while the Program Start parameter is displayed.
The program END status can also be cleared using an event. If the program
start function is assigned to an event, however, the program end status cannot
be cleared from the Program Start parameter display, which will function only
as a monitor display.
Operating Procedure Perform the following procedure to use the simple program function.
In this example, the program pattern will be set to STOP, the soak time to
10 min, and the wait band to 3.
132
Wait band = 3
Set point
PV
RSET STRT Soak time = 10 min END display

STOP END output
Operation Level
C PV/SP
25
100
in-t
5
Initial Setting Level 2. Select the Program Pattern parameter by pressing the M Key.
Program Pattern
ptrn
off
3. Use the U Key to set the parameter to STOP.
ptrn
stop
25
100
Adjustment Level
l.adj Display
Adjustment Level 6. Select the Soak Time parameter by pressing the M Key.
Soak Time
soak
1
7. Use the U Key to set the parameter to 10. (The soak time unit is set in
soak Soak Time Unit parameter in the advanced function setting level. The de-
fault is m (minutes).
10
133
Soak Time
soak
Adjustment Level 6. Select the Soak Time parameter by pressing the M Key.
1
soak 7. Use the U Key to set the parameter to 10. (The soak time unit is set in
10
Soak Time Unit parameter in the advanced function setting level. The de-
fault is m (minutes).
134
4-15-3 Application Example Using a Simple Program

The program will be started by changing the setting of the Program Start
parameter. The following example shows using a simple program with the pro-
gram pattern set to STOP.
Wait band
Set point
PV
Soak time Soak time Soak time
END display
END output
RUN STOP RUN

RUN/STOP
status
STRT RSET STRT RSET

STRT
Program
start
(1) (2) (3) (4) (5) (6) (7) (8) (9) (10)
Timing Description
(1) The Program Start parameter was changed from RSET to STRT using either an event or key operations.
The RUN/STOP status automatically changes to RUN mode when the above operation is performed.
(2) The Program Start parameter was changed from STRT to RSET using either an event or key operations
before the soak time expired.
The RUN/STOP status automatically changes to STOP mode when the above operation is performed.
(3) The Program Start parameter is again changed from RSET to STRT using either an event or key opera-
tions.
The RUN/STOP status will automatically change to RUN mode when the above operation is performed.
(4) The RUN/STOP status automatically changes to STOP mode when soak time expires.
END flashes on the No. 2 display and the program END output turns ON.
(5) The Program Start parameter is changed from STRT to RSET using either an event or key operations.
The END display is cleared and the program END output turns OFF.
(6) Key operations are used to switch the RUN/STOP status to RUN with the Program Start parameter set to
RSET (stopped).
Normal control operation is started.
(7) The Program Start parameter is changed from RSET to STRT after the process value stabilizes.
The RUN/STOP status remains as RUN.
(8) Key operations are used to change the RUN/STOP status to STOP (during program operation).
Measuring the soak time is continued within the wait band. (Measuring the soak time stops when the pro-
cess value leaves the wait band.)
(9) Key operations are used to change the RUN/STOP status to RUN.
Measuring the soak time is continued within the wait band (continuing from the time between (7) and (9)).
(10) The RUN/STOP status automatically changes to STOP mode when the measured time reaches the soak
time.
END flashes on the No. 2 display and the program END output turns ON.
135
Output Adjustment Functions Section 4-16
4-16 Output Adjustment Functions

4-16-1 Output Limits
Output limits can be set to control the output using the upper and lower
limits to the calculated MV.
The following MV takes priority over the MV limits.
Manual MV (See note.)
MV at stop
MV at PV error
Output
100%
MV upper limit
MV lower limit
0%
Note When the manual MV limit is enabled, the manual MV will be re-
stricted by the MV limit.
For heating/cooling control, upper and lower limits are set of overall heat-
ing/cooling control. (They cannot be set separately for heating/cooling.)
Output Heating MV Cooling MV
MV lower limit
MV upper limit
4-16-2 MV at Stop
The MV when control is stopped can be set.
For heating/cooling control, the MV at stop will apply to the cooling side if
the MV is negative and to the heating side if the MV is positive.
When setting the MV when control is stopped, set the MV at Stop and
Error Addition parameter (advanced function setting level) to ON.
The default is 0.0, so an MV will not be output for either standard or heat-
ing/cooling control.
MV at STOP 5.0 to 105.0 for standard % 0.00
control
105.0 to 105.0 (heating/cool-
ing control)
Note The order of priority is as follows: Manual MV > MV at stop > MV at PV error.
136
Using the Extraction of Square Root Parameter Section 4-17
4-16-3 MV at PV Error
The MV to be output for input errors can be set.
The MV at stop takes priority when stopped and the manual MV takes pri-
ority in manual mode.
MV at PV ERROR 5.0 to 105.0 for standard % 0.0
control
ing control)
Note The order of priority is as follows: Manual MV > MV at stop > MV at PV error.
The order of priority of the MVs is illustrated in the following diagram.
Manual MV
MV upper limit MV at PV Error (See note.)
RUN/STOP
Manipulated variable
Output
PID
calculations
Input error Auto/manual switch
Time
MV at Stop
MV lower limit
Note When the Manual MV Limit Enable parameter is set to ON, the setting range
will be the MV lower limit to the MV upper limit.
4-17 Using the Extraction of Square Root Parameter

Extraction of Square
Roots
Extraction of Square Root Enable For analog inputs, the Extraction of Square Root parameter is provided
for inputs so that differential pressure-type flow meter signals can be
sqr directly input.
off The default setting for the Extraction of Square Root parameter is OFF.
The Extraction of Square Root Enable parameter must be set to ON in
order to use this function.
Extraction of Square Root Low-cut If the PV input (i.e., the input before extracting the square root) is higher
Point than 0.0% and lower than the low cut point set in the Extraction of
Square Root Low-Cut Point parameter, the results of extracting the
sqrp square root will be 0.0%. If the PV input is lower than 0.0% or higher
0.0 than 100.0%, extraction of the square root will not be executed, so the
result will be equal to the PV input. The low-cut point is set as normal-
ized data for each input, with 0.0 as the lower limit and 100.0 as the
upper limit for the input setting range.
137
Using the Extraction of Square Root Parameter Section 4-17
Extraction of
square root
100% FS
Extraction of square
root low-cut point
0 100% FS
Argument 1 (Input Data)
Parameter name Setting rage Unit Default

Extraction of Square OFF: Disabled, ON: Enabled --- OFF
Root Enable
Extraction of Square 0.0 to 100.0 % 0.0
Root Low-cut Point
Operating Procedure This procedure sets the Extraction of Square Root Low-cut Point parameter to
10.0%.
Operation Level
C PV/SP
25
100
in-t
0
Extraction 2. Press the M Key to select the Extraction of Square Root Enable param-
sqr of Square
Root Enable
eter.
off
Extraction 3. Use the U Key to select ON.

sqr of Square
Root Enable
on
25
100
l.adj
Extraction of 6. Select the Extraction of Square Root Low-cut Point parameter by press-
sqrp Square Root
Low-cut Point
ing the M Key.
0.0
138
Setting the Width of MV Variation Section 4-18
Extraction of 7. Use the U Key to set the parameter to 10.0.

sqrp Square Root
Low-cut Point
10.0
Operation Level 8. Press the O Key to return to the operation level.
C PV/SP
25
100
4-18 Setting the Width of MV Variation

MV Change Rate Limit
MV Change Rate Limit (Heating) The MV change rate limit sets the maximum allowable width of change
in the MV per second. If the change in the MV exceeds this setting, the
orl MV will be changed by the MV change rate limit until the calculated
value is reached. This function is disabled when the setting is 0.0.
0.0
The MV change rate limit does not function in the following situations:
In manual mode
During ST execution (Cannot be set when ST is ON.)
During AT execution
During ON/OFF control
While stopped (during MV at Stop output)
During MV at PV Error output
Parameter name Setting rage Unit Default

MV Change Rate 0.0 to 100.0 %/s 0.0
Limit
Operating Procedure This procedure sets the MV change rate limit to 5.0%/s. The related parame-
ters are as follows:
PIDON/OFF = PID
ST = OFF
Operation Level
C PV/SP
25
100
in-t
0
PIDON/OFF 2. Select the PID ON/OFF parameter by pressing the M Key.
cntl
onof
139
Setting the Width of MV Variation Section 4-18
PIDON/OFF 3. Use the U Key to select 2-PID control.

cntl
pid
ST 4. Press the M Key to select the ST parameter.

st
on
ST 5. Press the D Key to select OFF.
st
off
25
100
l.adj
MV 8. Press the M Key to select the MV Change Rate Limit parameter.
orl Change
Rate Limit
0.0
9. Use the U Key to set the parameter to 5.0.
MV
orl Change
Rate Limit
5.0
Operation Level 10. Press the O Key to return to the operation level.
C PV/SP
25
100
140
Setting the PF Key Section 4-19
4-19 Setting the PF Key

4-19-1 PF Setting (Function Key)
PF Setting Pressing the PF Key for at least one second executes the operation set
in the PF Setting parameter (E5AN/EN only).
pf
a-m
Set value Symbol Setting Function

OFF off Disabled Does not operate as a function key.
RUN run RUN Specifies RUN status.
STOP stop STOP Specifies STOP status.
R-S r-s RUN/STOP reverse Specifies reversing the RUN/STOP
operation operation status.
AT-2 at-2 100% AT Specifies reversing the 100% AT Exe-
Execute/Cancel cute/Cancel status. (See note 1.)
AT-1 at-1 40% AT Specifies reversing the 40% AT Exe-
Execute/Cancel cute/Cancel status. (See note 1.)
LAT lat Alarm Latch Cancel Specifies canceling all alarm latches.
(See note 2.)
A-M a-m Auto/Manual Specifies reversing the Auto/Manual
status. (See note 3.)
PFDP pfdp Monitor/Setting Item Specifies the monitor/setting item dis-
play. Select the monitor setting item
according to the Monitor/Setting Item 1
to 5 parameters (advanced function
setting level).
Note (1) When AT cancel is specified, it means that AT is cancelled regardless of

whether the AT currently being executed is 100% AT or 40% AT.
(2) Alarms 1 to 3, heater burnout, HS alarms, and heater overcurrent latches
are cancelled.
(3) For details on auto/manual operations using the PF Key, refer to 4-13 Per-
forming Manual Control.
(4) Pressing the PF Key for at least one second executes operation accord-
ing to the set value. When the Monitor/Setting Item parameter is selected,
however, the display is changed in order from Monitor/Setting Item 1 to 5
each time the key is pressed.
(5) This function is enabled when PF Key Protect is OFF.
Monitor/Setting Item
Monitor/Setting Item 1 Setting the PF Setting parameter to the Monitor/Setting Item makes it possi-
ble to display monitor/setting items using the function key. The following
pfd1Item 5 table shows the details of the settings. For setting (monitor) ranges, refer to
the applicable parameter.
pfd5
1
0
141
Setting the PF Key Section 4-19
Set Setting Remarks

value Monitor/Setting Symbol
0 Disabled ---
1 PV/SP/Multi-SP Can be set. (SP) ---
2 PV/SP/MV (See note.) Can be set. (SP) ---
3 PV/SP /Soak time remain Can be set. (SP) ---
4 Proportional band (P) Can be set. p
5 Integral time (I) Can be set. i
6 Derivative time (D) Can be set. d
7 Alarm value 1 Can be set. al-1
8 Alarm value upper limit 1 Can be set. al1h
9 Alarm value lower limit 1 Can be set. al1l
Note For details on MV settings for heating and cooling control, refer to
MV Display for Heating and Cooling Control on page 84.
Setting Monitor/Setting Items
Pressing the PF Key in either the operation or adjustment level displays the
applicable monitor/setting items. Press the PF Key to display in order Monitor/
Setting Items 1 to 5. After Monitor/Setting Item 5 has been displayed, the dis-
play will switch to the top parameter in the operation level.
Note (1) Items set as disabled in the Monitor/Setting Items 1 to 5 parameters will
not be displayed, and the display will skip to the next enabled setting.
(2) While a monitor/setting item is being displayed, the display will be
switched to the top parameter in the operation level if the M Key or the
O Key is pressed.
Operating Procedure This procedure sets the PF Setting parameter to PFDP, and the Monitor/Set-
ting Item 1 parameter to 7 (Alarm Value 1).
Operation Level
C PV/SP
25
100
in-t
5
Setting Level
ing the M Key.
-169
142
Counting Control Output ON/OFF Operations Section 4-20
Advanced Function Setting Level 3. Press the D Key to enter the password (169). It is possible to move to
Parameter the advanced function setting level by either pressing the M Key or wait-
init Initialization ing two seconds without pressing any key.
off
PF Setting 4. Press the M Key to select the PF Setting parameter.
pf
a-m
5. Press the U Key to select PFDP (Monitor/Setting Item).
PF Setting
pf
pfdp
Monitor/Setting 6. Press the M Key to select the Monitor/Setting Item 1 parameter.
pfd1 Item 1
1
7. Press the U Key to select 7 (Alarm Value 1).
Monitor/Setting
pfd1 Item 1
7
in-t
5
C
25 alm

100
Monitor/Setting Item Level 10. Press the PF Key to display Alarm Value 1.
C Monitor/Setting
al-1 Item Display 1
0
4-20 Counting Control Output ON/OFF Operations

4-20-1 Control Output ON/OFF Count Function
With Control Output 1 and 2 ON/OFF outputs (relay outputs or voltage outputs
for driving SSR), the number of times that a control output turns ON and OFF
can be counted. Based on the control output ON/OFF count alarm set value,
an alarm can be output and an error can be displayed if the set count value is
exceeded.
The default setting of the Control Output ON/OFF Alarm Setting parameter is
0. ON/OFF operations are not counted when this parameter is set to 0. To
enable counting ON/OFF operations, change the setting to a value other than
0.
143
Counting Control Output ON/OFF Operations Section 4-20
Control Output ON/ This function is not displayed when the Control Output 1 ON/OFF Alarm Set-
OFF Counter Monitor ting and the Control Output 2 ON/OFF Alarm Setting parameter are set to 0,
Function or when the control outputs are set for linear outputs.
Control Output 1 ON/OFF Count Monitor 0 to 9999 100 times 0
Control Output 2 ON/OFF Count Monitor 0 to 9999 100 times 0
Display When ON/OFF Count Alarm Occurs

When an ON/OFF count alarm occurs, the PV display in the No. 1 display
shown below alternates with the ralm display on the No. 2 display.
PV
PV/SP (Including the items displayed by setting the PV/SP Display
Screen Selection parameter.)
PV/Manual MV, PV/SP/Manual MV
PV/SP displayed for the monitor/setting items
Normal ON/OFF Count Alarm
C C
PV/SP 25 25 Alternating
display
100 ralm 100
Control Output ON/ If the ON/OFF counter exceeds the control output ON/OFF count alarm set
OFF Count Alarm value, an ON/OFF count alarm will occur. The alarm status can be assigned
Function to a control output or an auxiliary output, or it can be displayed at the Control-
ler. The ON/OFF count alarm set value function is disabled by setting the ON/
OFF count alarm set value to 0.
Control Output 1 ON/OFF Alarm Set- 0 to 9999 100 times 0
ting
Control Output 2 ON/OFF Alarm Set- 0 to 9999 100 times 0
ting
ON/OFF Counter Reset Function

The ON/OFF counter can be reset for a specific control output.
ON/OFF Counter Reset 0: Disable the counter reset --- 0
function.
1: Reset the control output 1
ON/OFF counter.
ON/OFF counter.
Note After the counter has been reset, the control output ON/OFF count monitor
value will be automatically returned to 0.
If an error occurs in the control output ON/OFF counter data, the ON/OFF
count monitor value will be set to 9999 and an ON/OFF count alarm will occur.
The alarm can be cleared by resetting the ON/OFF counter.
144
Displaying PV/SV Status Section 4-21
Operating Procedure This procedure sets the Control Output 1 ON/OFF Alarm Setting parameter to
10 (1,000 times).
in-t
5
Setting Level
-169
Advanced Function Setting Level 3. Use the D Key to enter the password (169). It is possible to move to
Parameter the advanced function setting level by either pressing the M Key or wait-
init Initialization ing two seconds without pressing any key.
off
Control Output 4. Press the M Key to select the Control Output 1 ON/OFF Count Alarm Set
ra1 1 ON/OFF
Count Alarm
Value parameter.
0 Set Value
Control Output 5. Use the U Key to set the parameter to 10.

ra1 1 ON/OFF
Count Alarm
10 Set Value
Initial Setting Level 6. Press the O Key for at least one second to move to the initial setting lev-
Input Type el.
in-t
5
Operation Level 7. Press the O Key for at least one second to move to the operation level.
C
25 alm

100
4-21 Displaying PV/SV Status

4-21-1 PV and SV Status Display Functions
PV Status Display The PV in the PV/SP, PV, or PV/Manual MV Display and the control and alarm
Function status specified for the PV status display function are alternately displayed in
0.5-s cycles.
Set value Symbol Function
OFF off No PV status display
Manual manu MANU is alternately displayed during
manual control.
Stop stop STOP is alternately displayed while oper-
ation is stopped.
Alarm 1 alm1 ALM1 is alternately displayed during
Alarm 1 status.
Alarm 2 status.
145
Displaying PV/SV Status Section 4-21

Alarm 3 status.
Alarm 1 to 3 OR status alm ALM is alternately displayed when Alarm
1, 2, or 3 is set to ON.
Heater Alarm (See note.) ha HA is alternately displayed when a heater
burnout alarm, HS alarm, or heater over-
current alarm is ON.
The default is OFF.

Note HA can be selected for models that do not support heater burnout detection,
but the function will be disabled.
Example: When STOP Is Selected for the PV Status Display Function
When RUN/STOP
Normal is STOP
C C
PV/SP
25 stop Alternating
display
100 100 25
SV Status Display The SP, Blank, or Manual MV in the PV/SP, PV, or PV/Manual MV Display and
Function the control and alarm status specified for the SV status display function are
alternately displayed in 0.5-s cycles.
OFF off No SV status display
Manual manu MANU is alternately displayed during
manual control.
Stop stop STOP is alternately displayed while oper-
ation is stopped.
Alarm 1 status.
Alarm 2 status.
Alarm 3 status.
Alarm 1 to 3 OR status alm ALM is alternately displayed when Alarm
1, 2, or 3 is set to ON.
Heater Alarm (See note.) ha HA is alternately displayed when a heater
burnout alarm, HS alarm, or heater over-
current alarm is ON.
The default is OFF.

Note HA can be selected for models that do not support heater burnout detection,
but the function will be disabled.
Example: When ALM1 Is Selected for the SV Status Display Function
Normal When ALM1 Is ON
C C
PV/SP
25 25 Alternating
display
100 alm1 100
146
Logic Operations Section 4-22
Operating Procedure This procedure sets the PV Status Display Function parameter to ALM1.
in-t
5
Setting Level
-169
Advanced Function Setting Level 3. Use the D Key to enter the password (169). It is possible to move to the
Parameter advanced function setting level by either pressing the M Key or waiting
init Initialization two seconds without pressing any key.
off
PV Status 4. Press the M Key to select the PV Status Display Function parameter.
pvst Display
Function
off
PV Status 5. Press the U Key to select ALM1.
pvst Display
Function
alm1
Initial Setting Level 6. Press the O Key for at least one second to move to the initial setting lev-
Input Type el.
in-t
5
Operation Level 7. Press the O Key for at least one second to move to the operation level.
C If the Alarm 1 status is ON, PV and ALM1 will be alternately displayed.
25 alm1

100
4-22 Logic Operations

4-22-1 The Logic Operation Function (CX-Thermo)
The logic operation function logically calculates as 1 or 0 the Controller
status (alarms, SP ramp, RUN/STOP, auto/manual, etc.) and the external
event input status, and outputs the results to work bits. The work bit status
can be output to auxiliary or control outputs, and operating status can be
switched according to the work bit status.
Work bit logic operation can be set from 1 to 8. Set them to No operation
(Always OFF) (the default) when the work bits are not to be used. When
logic operations are being used, a dot will be displayed on the No. 2 dis-
play of the adjustment level display
Adjustment Level
Adjustment level display
l.adj
.
Dot displayed.
147
4-22-2 Using Logic Operations

Logic operations are set using the CX-Thermo.
Starting Logic There are two ways to start logic operations.

Operations Select Logic Operation Editor from the CX-Thermo tree, and click the
Start Button.
Select Logic Operation Editor from the CX-Thermo Options Menu.
Making the Settings The following display will appear on the Logic Operation Editor Setting Win-
dow. Set each of the parameters.
1,2,3... 1. Displaying the Library Import Dialog Box

Logic operation samples for specific cases are set in the library in advance.
Examples of settings for specific cases are loaded by selecting them from
the library list and clicking the OK Button.
148
Example: Selecting Library 1
2. Switching Work Bit Operations

Select the work bit logic operations from the Operation of Work Bit 1 to Op-
eration of Work Bit 8 Tab Pages.
3. Selecting the Operation Type
From one to four operations are supported. If work bits are not to be used,
set them to No operation (Always OFF) (the default).
No operation (Always OFF)
Operation 1
(A and B) or (C and D)
When conditions A
and B or conditions C
and D are satisfied
Operation 2
(A or C) and (B or D)
When condition A or
C and condition B or
D are satisfied
149
Operation 3
A or B or C or D
When condition A,
B, C or D is satisfied
Operation 4
A and B and C
and D
When conditions
A, B, C and D are
all satisfied
150
4. Selecting Input Assignments

Select the input assignment for the work bit logic operation from the follow-
ing settings.
Parameter Setting range
name
Work Bit 1 Input 0: Always OFF
Assignment A 1: Always ON
2: ON for one cycle when power is turned ON
3: Event input 1 (external input) (See note 1.)
7: Alarm 1
8: Alarm 2
9: Alarm 3
10: Control output ON/OFF count alarm (See note 2.)
11: Control output (heating)
12: Control output (cooling)
13: Input error
14: Disabled
15: HB (heater burnout) alarm
16: HS alarm
17: OC (heater overcurrent) alarm
18: Auto/Manual
19: RUN/STOP
20: Disabled
21: Program start
22: AT Execute/Cancel
23: SP ramp operating
24: Multi-SP (bit 0)
25: Multi-SP (bit 1)
26: Disabled
27: Program end output
28: Work bit 1
29: Work bit 2
30: Work bit 3
31: Work bit 4
32: Work bit 5
33: Work bit 6
34: Work bit 7
35: Work bit 8
Work Bit 1 Input Same as for work bit 1 input assignment A
Assignment B
Assignment C
Assignment D
to to
Assignment D
Note (1) The event inputs that can be used depend on the Controller model.
151
(2) Turns ON when either the control output 1 or 2 ON/OFF count alarm is
ON.
5. Switching between Normally Open and Normally Closed for Inputs A to D
Click the condition to switch between normally open and normally closed
inputs A to D.
Normally open Normally closed
6. Switching between Normally Open and Normally Closed for Work Bits
Click the condition to switch between normally open and normally closed
work bits.
Normally open Normally closed
7. Setting ON Delay Times

When an input with ON delay turns ON, the output will turn ON after the
set delay time has elapsed. The setting range is 0 to 9,999. The default is
0 (disabled).
8. Setting OFF Delay Times
When an input with OFF delay turns OFF, the output will turn OFF after the
set delay time has elapsed. The setting range is 0 to 9,999. The default is
0 (disabled).
9. Switching ON/OFF Delay Time Unit
Select either seconds or minutes for the ON/OFF delay time unit. The de-
fault is seconds.
10. Selecting the Number of Multi-SP Uses
Select the number of Multi-SP uses from 0 to 2.
11. Changing Event Input Data
Select the event input conditions from the following setting ranges.
Parameter name Setting range
Event Input Data 1 0: Not assigned.
1: Event input 1 (external input)
5: Work bit 1
6: Work bit 2
7: Work bit 3
8: Work bit 4
9: Work bit 5
10: Work bit 6
11: Work bit 7
12: Work bit 8
Event Input Data 2 Same as for event input data 1
152
Note The event input data can be changed from the default setting even
if there is no event input terminal (external input). By changing the
default setting, the event input assignment parameters will be dis-
played at the Controller display and can be set from the Controller.
12. Changing the Event Input Assignment Function
Select the setting for the event input assignment.
When a work bit is selected as event input data, Communications Write
Enable/Disable cannot be assigned to an event input.
13. Changing Control Output and Auxiliary Output Settings
Control output and auxiliary output assignments can be changed. The
items that can be changed depend on the Controller model. For details, re-
fer to 3-5-3 Assigned Output Functions.
Assigning a work bit to either a control output or to an auxiliary output is
also considered to be the same as assigning an alarm. For example, if
work bit 1 is set for the Auxiliary Output 1 Assignment parameter, then
alarms 1 to 3 have been assigned.
14. Displaying Parameter Guides
A description of the parameters can be displayed.
15. Displaying the Work Bit Use Destinations
Display a list of destinations where the work bits are used.
Operating Procedure This procedure uses event input 2 to change to RUN or STOP.
Event input 2 ON: RUN
Event input 2 OFF: STOP
Event 2 Work bit 1
Reverse
operation
Always OFF
Always OFF
Always OFF
1. Select Logic Operation Editor from the CX-Thermo

tree, and click the Start Button.
2. The Logic Operation Editor will be displayed. Confirm

that the screen for work bit 1 is displayed, and select
Operation 3 from the Operation Type Field.
153
3. Set the operation by selecting one of the following:

Work bit 1 input assignment A = 4: Event input 2 (ex-
ternal input)
Work bit 1 input assignment B = 0: Always OFF
Work bit 1 input assignment C = 0: Always OFF
Work bit 1 input assignment D = 0: Always OFF
4. Invert work bit 1. Click (Normally open) to change
it to (Normally closed).
5. Assign RUN/STOP to event input 2. Set 5: Work bit 1

for the event input data for event input 2, and set RUN/
STOP for the assignment function.
6. Closing the Logic Operation Editor Dialog Box
Click the Close Button.
This completes the procedure for setting parameters
using the CX-Thermo. Transfer the settings to the Control-
ler to set the Controller. Refer to CX-Thermo help for the
procedure to transfer the settings.
Operating Procedure This procedure outputs alarm 1 status to auxiliary output 1 during operation
(RUN). A library object is used to make the setting.
Alarm 1 RUN/STOP Work bit 1
Always OFF Always OFF
1. Select Logic Operation Editor from the CX-Thermo

tree, and click the Start Button.
2. Click the Import of Library Button.
154
3. Select Library 1 from the library list, and then click the
OK Button.
Confirm the following settings, and then click the OK
Button.
Work bit 1 operation type: Operation 1
Work bit 1 input assignment A = 7: Alarm 1
Work bit 1 input assignment B = 19: Invert for RUN/
STOP
Work bit 1 input assignment C = 0: Always OFF
Work bit 1 input assignment D = 0: Always OFF
Auxiliary output 1 = Work bit 1
4. Closing the Logic Operation Editor Dialog Box

Click the Close Button.
This completes the procedure for setting parameters
using the CX-Thermo. Transfer the settings to the Control-
ler to set the Controller. Refer to CX-Thermo help for the
procedure to transfer the settings.
155
156
SECTION 5
Parameters
This section describes the individual parameters used to setup, control, and monitor operation.
5-1 Conventions Used in this Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 158

5-1-1 Meanings of Icons Used in this Section . . . . . . . . . . . . . . . . . . . . . . 158
5-1-2 About Related Parameter Displays . . . . . . . . . . . . . . . . . . . . . . . . . . 158
5-1-3 The Order of Parameters in This Section . . . . . . . . . . . . . . . . . . . . . 158
5-1-4 Alarms. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 158
5-2 Protect Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159
5-3 Operation Level. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163
5-4 Adjustment Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 177
5-5 Monitor/Setting Item Level. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 196
5-6 Manual Control Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 197
5-7 Initial Setting Level. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 199
5-8 Advanced Function Setting Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 218
5-9 Communications Setting Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 255
157
Conventions Used in this Section Section 5-1
5-1 Conventions Used in this Section

5-1-1 Meanings of Icons Used in this Section
Describes the functions of the parameter.
Function
Describes the setting range and default of the parameter.
Setting
Used to indicate parameters used only for monitoring.
Monitor
Describes the parameter settings, such as those for Operation Commands,
and procedures.
Operation
Used to indicate information on descriptions in which the parameter is used or
the names of related parameters.
See
5-1-2 About Related Parameter Displays

Parameters are displayed only when the conditions for use given on the right
of the parameter heading are satisfied. Protected parameters are not dis-
played regardless of the conditions for use, but the settings of these parame-
ters are still valid.
The E5CN must be in operation, and

at AT Execute/Cancel control must be 2-PID control.
Displayed symbol Parameter name Conditions for use
5-1-3 The Order of Parameters in This Section

Parameters are described level by level.
The first page of each level describes the parameters in the level and the pro-
cedure to switch between parameters.
5-1-4 Alarms
It will be specified in this section when alarms are set for the Control Output 1
or 2 Assignment parameters, or for the Auxiliary Output 1 or 3 Assignment
parameters. For example, when alarm 1 is set for the Control Output 1 Assign-
ment parameter, it will be specified that alarm 1 is assigned.
Assigning a work bit to either control output 1 or 2 or to auxiliary output 1 to 3
is also considered to be the same as assigning an alarm. For example, if work
bit 1 is set for the Auxiliary Output 1 Assignment parameter, then alarms 1 to 3
have been assigned.
158
Protect Level Section 5-2
5-2 Protect Level

Four levels of protection are provided on the E5@N, operation/adjustment pro-
tect, initial setting/communications protect, setting change protect, and PF key
protect (E5AN/EN only). These protect levels prevent unwanted operation of
the keys on the front panel in varying degrees.
Power ON
Operation Adjustment
Level Level Press the O + M keys;
display will flash.
Press the
O Key less than 1 s. C
25
Press the O + M 100
Keys for at least 1 s. Press the O + M Keys
for at least 3 s. (See
note.)
Protect
Control in Progress Level
To move from the operation level to the protect level, press O and M Keys for
three seconds (see note) or more.
Note The time taken to move to the protect level can be adjusted by changing the
Move to Protect Level Time parameter setting.
Protect Level
Page
pmov Move to Protect Level

Displayed only when a password 160
0
is set.
M
oapt Operation/Adjustment 160

0 Protect
M
icpt Initial Setting/ 160
1 Communications Protect
M
wtpt Setting Change Protect 161
off
M
pfpt PF Key Protect 161
off
M
pmsk Parameter Mask Enable 161
on
M
prlp Password to Move to
Protect Level 162
0
M
Parameters that are protected will not be displayed and their settings cannot
be changed.
159
The Password to Move to Protect

pmov Move to Protect Level Level password must not be set to 0.
The password to move to the protect level is entered for this parameter.
The password to move to the protect level (i.e., the password set for the
Password to Move to Protect Level parameter) is entered for this parame-
ter.
Function
The Operation/Adjustment Protect parameter will be displayed if the cor-
rect password is entered.
Related Parameters
See Password to move to protect level (protect level): Page 162
oapt Operation/Adjustment Protect

icpt Initial Setting/Communications Protect
These parameters specify the range of parameters to be protected. Shaded

settings are the defaults.
Operation/Adjustment Protect
The following table shows the relationship between set values and the range
Function of protection.
Level Set value

0 1 2 3
Operation PV Can be displayed Can be displayed Can be displayed Can be displayed
Setting Level PV/SP Can be displayed Can be displayed Can be displayed Can be displayed
and changed and changed and changed
Others Can be displayed Can be displayed Cannot be dis- Cannot be dis-
and changed and changed played and moving played and moving
to other levels is to other levels is
not possible not possible
Adjustment Level Can be displayed Cannot be dis- Cannot be dis- Cannot be dis-
and changed played and moving played and moving played and moving
to other levels is to other levels is to other levels is
not possible not possible not possible
Parameters are not protected when the set value is set to 0.
Initial Setting/Communications Protect

This protect level restricts movement to the initial setting level, communica-
tions setting level, and advanced function setting level.
Set Initial setting level Communications Advanced function
value setting level setting level
0 Possible to reach Possible to reach Possible to reach
1 Possible to reach Possible to reach Not possible to reach
2 Not possible to reach Not possible to reach Not possible to reach
160
The Event Input Assignment 1 and 2

wtpt Setting Change Protect parameters must not be set to set-
ting change enable/disable.
This parameter specifies the range of data to be protected. The shaded cell
indicates the default.
Change Setting Protect

Changes to settings using key operations are restricted.
Function When enabling and disabling of setting changes by event inputs assignment 1
and 2 is selected, this parameter is not displayed.
Setting range Default
on: Enabled, off: Disabled on
Setting Set value Description

OFF Settings can be changed using key operations.
ON Settings cannot be changed using key operations. (The protect level
settings, however, can be changed.)
The all protect indication ( ) will light when setting is ON.
The Controller must have a PF Key

pfpt PF Key Protect (E5AN/EN).
PF Key Protect
This parameter enables and disables PF Key operation (E5AN/EN only).
Function
Set value Description
OFF PF Key enabled
ON PF Key disabled (Operation as a function key is prohibited.)
Setting
The shaded cell indicates the default.
This parameter is displayed only

pmsk Parameter Mask Enable when a parameter mask has been
set from the Setup Tool.
This parameter turns the parameter mask function ON and OFF.
Function

Setting Note A parameter mask can be used to hide the displays of parameters that are not
needed. The parameter mask function is provided by the Setup Tool.
Setup Tool: CX-Thermo (EST2-2C-MV4)
161
prlp Password to Move to Protect Level
This parameter is used to set the password to move to the protect level.
To prevent setting the password incorrectly, the U and O Keys or D and
O Keys must be pressed simultaneously to set the password.
Function

1999 to 9999 0
Setting
Set this parameter to 0 when no password is to be set.
Related Parameters
See Move to protect level (protect level): Page 160
Note Protection cannot be cleared or changed without the password. Be careful not
to forget it. If you forget the password, contact your OMRON sales representa-
tive.
162
Operation Level Section 5-3
5-3 Operation Level

Display this level to perform control operations on the E5@N. You can set
alarm values, monitor the manipulated variable, and perform other operations
in this level.
In the advanced function setting level, you can set a parameter to hide or
show the set points.
Power ON
Level Level
Press the
O Key less than 1 s.
least 1 s; display will flash.
Press the O Key C
for at least 1 s. 25 Press the O Key for at least 3 s.

100 Control stops.
Communi-
Initial Setting cations
Level Setting
Level Control in progress
Press the
O Key for less than 1 s. Control stopped
This level is displayed immediately after the power is turned ON.

To move to other levels, press the O Key or the O and M Keys.
163
Operation Level
Page Page
25 Process Value al-1 Alarm Value 1

C C
165 172
0
M M
25 Process Value/Set Point 165 al1h Alarm Value Upper
C C
174
0 (See note.) 0 Limit 1
M M
a-m Auto/Manual Switch al1l Alarm Value Lower
C
166 174
0 Limit 1
M M
m-sp Multi-SP Set
al-2 Alarm Value 2
C
Point Setting
167 173
0 0
M M
sp-m Set Point During SP
C C
167 al2h Alarm Value Upper 174
0 Ramp 0 Limit 2
M M
ct1 Heater Current 1
C
168 al2l Alarm Value Lower 174
0.0 Value Monitor 0 Limit 2
M M
ct2 Heater Current 2 al-3 Alarm Value 3
C
169 173
0.0 Value Monitor 0
M M
lcr1 Leakage Current 1 al3h Alarm Value Upper
C
170 Limit 3
175
0.0 Monitor 0
M M
lcr2 Leakage Current 2 al3l Alarm Value Lower
C
170 Limit 3 175
0.0 Monitor 0
M M
prst Program Start 171 o MV Monitor (Heating) 175
rset 0.0
M M
sktr Soak Time Remain 171 c-o MV Monitor (Cooling) 176
0 0.0
M M
r-s RUN/STOP 172
run
M
Note For details on the displays of Controllers with a No. 3 display (E5AN/EN), refer
to Process Value/Set Point on page 165.
164
The Additional PV Display parameter

Process Value must be set to ON.
The process value is displayed on the No. 1 display, and nothing is displayed
on the No. 2 and No. 3 (E5AN/EN only) displays.
Function
Monitor range Unit

Process value Temperature: According to indication range for EU
each sensor.
Monitor Analog: Scaling lower limit 5% FS to Scaling
upper limit +5% FS (Refer to page 303.)
During temperature input, the decimal point position depends on the currently
selected sensor, and during analog input it depends on the Decimal Point
parameter setting.
The default setting is for a K thermocouple (5).
An s.err error will be displayed if the input type setting is incorrect. To clear
the s.err error, correct the input type or wiring, and then cycle the power.
Related Parameters
See Input type: Page 200, Set point upper limit, Set point lower limit: Page 203 (ini-
tial setting level)
Process Value/Set Point (Display 1)

Process Value/Set Point (Display 2) (E5AN/EN only)
The process value is displayed on the No. 1 display, and the set point is dis-
played on the No. 2 display.
Function
Monitor range Unit

Monitor each sensor.
Analog: Scaling lower limit 5% FS to Scaling
Setting range Unit

Set point SP lower limit to SP upper limit EU
During temperature input, the decimal point position depends on the currently
selected sensor, and during analog input it depends on the Decimal Point
parameter setting.
165
No. 3 Display (E5AN/EN)

The following table shows the contents of the No. 3 display, according to the
setting of the PV/SP Display Screen Selection parameter.
0 Only the PV and SP are displayed. (The No. 3 display is not
shown.)
1 PV/SP/Multi-SP and PV/SP/MV are displayed in order.
2 PV/SP/MV and PV/SP/Multi-SP are displayed in order.
3 Only PV/SP/Multi-SP are displayed.
4 PV/SP/MV are displayed
5 PV/SP/Multi-SP and PV/SP/Soak time remain are displayed in
order.
6 PV/SP/MV and PV/SP/Soak time remain are displayed in order.
7 Only PV/SP/Soak time remain are displayed.
A 2-level display is set when shipped from the factory.

When 1, 2, 5, or 6 is selected, press the M Key to display PV/SP (Display 2).
Example: When the PV/SP Display Screen Selection Parameter Is Set to 2
Operation Level
PV/SP (Display 1) PV/SP (Display 2)
Press the M C
C
25 key. 25
100 100
50.0 sp0
PV/SP/MV PV/SP/Multi-SP
Related Parameters
See Input type: Page 200, Set point upper limit, Set point lower limit: Page 203 (ini-
tial setting level)
PV/SP display screen selection (advanced function setting level): Page 249

parameters must not be set to Auto/
Manual and the Auto/Manual Select
a-m Auto/Manual Switch Addition parameter must be set to
ON.
The control must be set to 2-PID
control.
This parameter switches the Controller between automatic and manual

modes.
If the O Key is pressed for at least 3 seconds when the Auto/Manual
Operation Switch parameter is displayed, the manual mode will be entered and the
manual control level will be displayed.
This parameter will not be displayed if an event input is set to MANU
(auto/manual).
Related Parameters
See PID ON/OFF (initial setting level): Page 204
Auto/manual select addition (advanced function setting level): Page 234
166
Multi-SP Set Point Setting The Multi-SP Uses parameter must

m-sp be set to ON.
(Set Points 0 to 3)
To use the multi-SP function, preset the four set points (SP 0 to 3) in the
adjustment level, and then switch the set point either by operating the keys or
by using external input signals (event inputs).
Function
This parameter is used to select set points 0 to 3.
The SP Ramp Set Value parameter

must not be set to OFF.
sp-m Set Point During SP Ramp The ST parameter must be set to
OFF.
This parameter monitors the set point during SP ramp operation.

A ramp is used to restrict the change width of the set point as a rate of
change.
Function
This parameter is displayed when a set value is input for the SP Ramp Set
Value parameter (adjustment level).
When not in ramp operation, the set point will be the same as the one dis-
played for the Process Value/Set Point parameter.
Monitor range Unit
SP: SP lower limit to SP upper limit EU
Monitor
Related Parameters
See Process value/set point (operation level): Page 165
SP ramp set value (adjustment level): Page 193
Set point upper limit, Set point lower limit (initial setting level): Page 203
167
Heater burnout, HS alarm, and

heater overcurrent detection must be
supported.
ct1 Heater Current 1 Value Monitor Alarm 1 must be assigned.
The Heater Burnout Detection or
Heater Overcurrent Use parameter
must be set to ON.
This parameter measures the heater current from the CT input used for
detecting heater burnout.
This parameter measures and displays the heater current value.
Function
Heater burnouts and heater overcurrent are not detected if the control
output (heating) ON time is 100 ms or less.
Monitor range Unit

0.0 to 55.0 A
Monitor
ffff is displayed when 55.0 A is exceeded.
If a heater burnout detection 1 or heater overcurrent detection 1 alarm is
output, the HA indicator will light and the No. 1 display for the heater cur-
rent 1 value monitor will flash.
Related Parameters
See Heater burnout detection 1, Heater burnout detection 2 (adjustment level):
Pages 181, and 183
HB ON/OFF (advanced function setting level): Page 222
Heater overcurrent detection 1, Heater overcurrent detection 2 (adjustment
level): Pages 181, and 183
Heater overcurrent use (advanced function setting level): Page 246
Error Displays ct1: Page 283
168
Heater burnout, HS alarm, and

supported (two CTs).
The Heater Burnout Detection or
must be set to ON.
Function
Monitor range Unit

0.0 to 55.0 A
Monitor
Related Parameters
Pages 181, and 183
169
Heater burnout, HS alarms, and

supported.
lcr1 Leakage Current 1 Monitor Alarm 1 must be assigned.
The HS Alarm Use parameter must
be set to ON.
detecting SSR short-circuits.
The heater current is measured and the leakage current 1 monitor is dis-
Function
played.
HS alarms are not detected if the control output (heating) OFF time is
100 ms or less.
Monitor range Unit
0.0 to 55.0 A
Monitor
If an HS alarm 1 alarm is output, the HA indicator will light and the No. 1
display for the leakage current 1 monitor will flash.
Related Parameters
See HS alarm 1, HS alarm 2 (adjustment level): Page 184
Failure detection (advanced function setting level): Page 235
Error Displays lcr1: Page 283

The HS Alarm Use parameter must
be set to ON.
Function
100 ms or less.
Monitor range Unit

0.0 to 55.0 A
Monitor
Related Parameters
HS alarm use (advanced function setting level): Page 235
170
The Program Pattern parameter

prst Program Start must not be set to OFF.
This parameter starts and stops the simple program function.

The RUN/STOP status will automatically switch to RUN when this param-
eter is set to STRT.
Function
The simple program will stop when this parameter is set to RSET.
This parameter will function as a monitor display for the start/stop status
of the simple program if an event input is selected to start the simple pro-
gram.

RSET Stops the simpler program. rset
Operation
STRT Starts the simpler program.
Related Parameters
See Soak time remain: Page 171, RUN/STOP: Page 172 (operation level)
Soak time, Wait band (adjustment level): Page 191
Program pattern (initial setting level): Page 205
Soak time unit (advanced function setting level): Page 243

sktr Soak Time Remain must not be set to OFF.
This parameter measures and displays the remaining time of the soak
time for the simple program function.
Function
Monitor range Unit

0 to 9999 min or h
Monitor
Related Parameters
See Program start (operation level): Page 171
171

r-s RUN/STOP parameters must not be set to RUN/
STOP.
This parameter starts and stops the control operation.

When run (RUN) is selected, control is started. When stop (STOP) is
selected, control is stopped. The STOP indicator will light when control.
Operation The default is run.
This parameter will not be displayed if an event input is set to RUN/STOP.

See
Alarm 1 must be assigned.

al-1 Alarm Value 1 The alarm 1 type must not be 0, 1, 4,
5, or 12.
This parameter is set to one of the input values X in the alarm type list.
This parameter sets the alarm value for alarm 1.
During temperature input, the decimal point position depends on the cur-
rently selected sensor, and during analog input it depends on the Decimal
Function
Point parameter setting.
Setting range Unit Default

1999 to 9999 EU 0
Setting
Related Parameters
See Input type: Page 200, Scaling upper limit, Scaling lower limit, Decimal point
(initial setting level): Page 202 (initial setting level)
Alarm 1 type (initial setting level): Page 207
Standby sequence reset: Page 221, Auxiliary output * open in alarm: Page
222, Alarm 1 hysteresis: Page 209, Alarm 1 latch: Page 227 (advanced func-
tion setting level)
172

5, or 12.
Function

1999 to 9999 EU 0
Setting
Related Parameters
tion setting level)

5, or 12.
Function

1999 to 9999 EU 0
Setting
Related Parameters
tion setting level)
173
al1h Alarm Value Upper Limit 1 Alarm 1 must be assigned.

The alarm 1 type must not be 1, 4, or
al1l Alarm Value Lower Limit 1 5.
These parameters independently set the alarm value upper and lower limits
when the mode for setting the upper and lower limits is selected for the Alarm
1 Type parameter (initial setting level).
This parameter sets the upper and lower limit values of alarm 1.
Function

1999 to 9999 EU 0
Setting
Related Parameters
See Input type: Page 200, Scaling upper limit, Scaling lower limit, Decimal point:
Page 202, Alarm 1 type: Page 207 (initial setting level), Standby sequence
reset: Page 221, Auxiliary output * open in alarm: Page 222, Alarm 1 hystere-
sis: Page 209, Alarm 1 latch: Page 227 (advanced function setting level

Function

1999 to 9999 EU 0
Setting
Related Parameters
sis: Page 209, Alarm 2 latch: Page 227 (advanced function setting level)
174

Function

1999 to 9999 EU 0
Setting
Related Parameters
sis: Page 209, Alarm 3 latch: Page 227 (advanced function setting level)
The MV Display parameter must be

o MV Monitor (Heating) set to ON.
This parameter is used to check the manipulated variable for the heating con-
trol output during operation.
This parameter cannot be set.
During standard control, the manipulated variable is monitored. During
heating/cooling control, the manipulated variables on the control output
Function
(heating) is monitored.
The default is OFF and the manipulated variable is not displayed.
Control Monitor range Unit

Standard 5.0 to 105.0 %
Monitor Heating/cooling 0.0 to 105.0 %
Related Parameters
See MV display (advanced function setting level): Page 227
175
The control system must be set to

heating/cooling control.
c-o MV Monitor (Cooling) The MV Display parameter must be
set to ON.
This parameter is used to check the manipulated variable for the cooling con-
trol output during operation.
This parameter cannot be set.
During heating/cooling control, the manipulated variable on the control
output (cooling) is monitored.
Function
The default is OFF and the manipulated variable is not displayed.
Control Monitor range Unit

Heating/cooling 0.0 to 105.0 %
Monitor
Related Parameters
See Standard or heating/cooling (initial setting level): Page 204
MV display (advanced function setting level): Page 227
176
Adjustment Level Section 5-4
5-4 Adjustment Level

This level is for executing AT (auto-tuning) and other operations, and for set
control parameters.
This level provides the basic Controller parameters for PID control (propor-
tional band, integral time, derivative time) and heating/cooling control.
Power ON
Level Level
Press the
Control in progress
To move to the adjustment level from the operation level, press the O Key
once.
The set points 0 to 3 in the adjustment level are the set values for switch-
ing the set point during multi-SP input.
The following parameters are displayed for Controllers with CT Inputs:
Heater current monitors, Leakage current monitors, heater burnout detec-
tions, HS alarms, and heater overcurrent detections.
Adjustment level parameters can be changed after setting the Operation/
Adjustment Protect parameter to 0. Displays and changing levels are not
possible if the Operation/Adjustment Protect parameter is set to 1 to 3.
Protection is set in the protect level.
177
Adjustment Level
Page Page Page

l.adj Adjustment Level 179
Display
sp-0 SP 0 c-db Dead Band
C C
186 189
M 0 0.0
M M
at AT Execute/Cancel sp-1 SP 1 of-r Manual Reset Value
C
179 186 190

off 0 50.0
M M M
cmwt Communications sp-2 SP 2 hys Hysteresis (Heating)
C C
180 186 190
off Writing 0 1.0
M M M
ct1 Heater Current 1 sp-3 SP 3 chys Hysteresis (Cooling)
C C
180 186 190

0.0 Value Monitor 0 1.0
M M M
hb1 Heater Burnout 181
C
ins Temperature Input 186 soak Soak Time 191
0.0 Detection 1 0.0 Shift 1
M M M
insh Upper Limit
wt-b Wait Band
C C
oc1 Heater Overcurrent 181 Temperature Input 187 191
50.0 Detection 1 0.0 off
M M Shift Value M
insl Lower Limit mv-s MV at Stop
C
ct2 Heater Current 2 Value 182 187 192

Monitor
0.0 0.0 Temperature Input 0.0
M M Shift Value M
p Proportional Band mv-e MV at PV Error
C
hb2 Heater Burnout 183 188 192
0.0 Detection 2 8.0 0.0
M M M
oc2 Heater Overcurrent 183 i Integral Time 188
C
sprt SP Ramp Set Value 193
50.0 Detection 2 233 off
M M M
lcr1 Leakage Current 1 184 d Derivative Time 188 ol-h MV Upper Limit 193
0.0 Monitor 40 105.0
M M M
hs1 HS Alarm 1 184 c-sc Cooling Coefficient 189 ol-l MV Lower Limit 193
50.0 1.00 -5.0
M M
M
lcr2 Leakage Current 2 185 orl MV Change Rate Limit 194
0.0 Monitor 0.0
M M
hs2 HS Alarm 2
185 sqrp Extraction of Square 194
50.0 0.0 Root Low-cut Point
M M
178
l.adj Adjustment Level Display
This parameter is displayed after moving to the adjustment level.

When a logic operation is set, a period . will be displayed on the No. 2. dis-
play.
This parameter indicates that the adjustment level has been entered.
(The Adjustment Level parameter will not be displayed again even if the
M Key is pressed in the adjustment level to scroll through the parame-
Function ters.)
The ramp must be in operation, and

2-PID control must be used. Event
at AT Execute/Cancel Input Assignments 1 and 2 parame-
ters must be other than 100% or
40% AT Execute/Cancel.
This parameter executes auto-tuning (AT).

The MV is forcibly increased and decreased around the set point to find
the characteristics of the control object. From the results, the PID con-
stants are automatically set in the Proportional Band (P), Integral Time (I),
Function and Derivative Time (D) parameters.
Both 100% AT and 40% AT are supported for AT.
Only 100% AT can be executed for heating and cooling control.
This parameter will not be displayed when either 100% or 40% AT exe-
cute/cancel is set to be executed using an event input.
Setting rage Default

OFF: AT Cancel OFF
Operation AT-2: 100%AT Execute
AT-1: 40%AT Execute
This parameter is normally off. Press the U Key and select at-2 or at-
1 to execute AT. AT cannot be executed when control is stopped or during
ON/OFF control.
When AT execution ends, the parameter setting automatically returns to
off.
Related Parameters
See Proportional band, Integral time, Derivative time (adjustment level): Page 188
PID ON/OFF (initial setting level): Page 204
179
Communications must be supported.

cmwt Communications Writing The Event Input Assignments 1 and
2 parameters must not be set to
enable communications writing.
This parameter enables/disables writing of parameters to the E5CN from

the host (personal computer) using communications.
This parameter is not displayed if communications write enable/disable is
Function
set for execution using an event input assignment 1 and 2.
ON: Writing enabled

OFF: Writing disabled
Default: OFF
Setting
Related Parameters
See MB command logic switching (advanced function setting level): Page 229
Communications Unit No., Communications baud rate, Communications data
length, Communications parity, Communications stop bits (communications
setting level): Page 255

supported.
The HB ON/OFF parameter or
must be set to ON.
Function
Heater burnouts or heater overcurrent are not detected if the control out-
put (heating) ON time is 100 ms or less.
Monitor range Unit
0.0 to 55.0 A
Monitor
Related Parameters
Pages 181, and 183
Error displays ct1: Page 283
180

supported.
hb1 Heater Burnout Detection 1 Alarm 1 must be assigned.
The HB ON/OFF parameter must be
set to ON.
This parameter sets the current for the heater burnout alarm to be output.
The heater burnout alarm is output when the heater current value falls
below the setting of this parameter.
When the set value is 0.0, the heater burnout alarm output is turned OFF.
Function
When the set value is 50.0, the heater burnout alarm output is turned ON.

0.0 to 50.0 A 0.0
Setting
Related Parameters
See Heater current 1 value monitor (adjustment level): Page 180
Heater burnout detection, Heater burnout latch, Heater burnout hysteresis
(advanced function setting level): Page 222

supported.
oc1 Heater Overcurrent Detection 1 Alarm 1 must be assigned.
The Heater Overcurrent Use ON/
OFF parameter must be set to ON.
This parameter sets the current value for heater overcurrent alarm outputs.
A heater overcurrent alarm is output when the heater current exceeds the
value set for this parameter.
When the set value is 50.0, the heater overcurrent alarm is turned OFF.
Function
When the set value is 0.0, the heater overcurrent alarm is turned ON.

0.0 to 50.0 A 50.0
Setting
Related Parameters
Heater overcurrent use, Heater overcurrent latch, Heater overcurrent hystere-
sis (advanced function setting level): Page 222
181

The HB ON/OFF or Heater Overcur-
rent Use parameter must be set to
ON.
Function
Monitor range Unit

0.0 to 55.0 A
Monitor
Related Parameters
Pages 181, and 183
182

hb2 Heater Burnout Detection 2 Alarm 1 must be assigned.
The HB ON/OFF parameter must be
set to ON.
This parameter sets the current for the heater burnout alarm to be output.
The heater burnout alarm is output when the heater current value falls
below the setting of this parameter.
When the set value is 0.0, the heater burnout alarm output is turned OFF.
Function
When the set value is 50.0, the heater burnout alarm output is turned ON.

0.0 to 50.0 A 0.0
Setting
Related Parameters
HB ON/OFF, Heater burnout latch, Heater burnout hysteresis (advanced func-
tion setting level): Page 222

oc2 Heater Overcurrent Detection 2 Alarm 1 must be assigned.
The Heater Overcurrent Use param-
eter must be set to ON.
This parameter sets the current value for heater overcurrent alarm outputs.
A heater overcurrent alarm is output when the heater current exceeds the
Function
When the set value is 50.0, the heater overcurrent alarm is turned OFF.
When the set value is 0.0, the heater overcurrent alarm is turned turn ON.

0.0 to 50.0 A 50.0
Setting
Related Parameters
Heater overcurrent use, Heater overcurrent latch, Heater overcurrent hystere-
sis (advanced function setting level): Page 222
183

supported.
The HS Alarm parameter must be
set to ON.
This parameter measures and displays the heater current when the heater is
OFF.
Function
100 ms or less.
Monitor range Unit

0.0 to 55.0 A
Monitor
Related Parameters

supported.
hs1 HS Alarm 1 Alarm 1 must be assigned.
set to ON.
This parameter sets the current for the HS alarm to be output.

An HS alarm is output when the leakage current value exceeds the set-
ting of this parameter.
Function
When the set value is 50.0, the HS alarm output is turned OFF. When the
set value is 0.0, the HS alarm output is turned ON.

0.0 to 50.0 A 50.0
Setting
Related Parameters
See Leakage current 1 monitor (adjustment level): Page 184
HS alarm, HS alarm latch, HS alarm hysteresis (advanced function setting
level): Page 235
184

set to ON.
100 ms or less.
Function
Monitor range Unit

0.0 to 55.0 A
Monitor
Related Parameters

hs2 HS Alarm 2 Alarm 1 must be assigned.
set to ON.
This parameter sets the current for the HS alarm to be output.

An HS alarm is output when the leakage current value exceeds the set-
ting of this parameter.
When the set value is 50.0, the HS alarm output is turned OFF. When the
Function
set value is 0.0, the HS alarm output will turn ON.

0.0 to 50.0 A 50.0
Setting
Related Parameters
See Leakage current 2 monitor (adjustment level): Page 185
HS alarm use, HS alarm latch, HS alarm hysteresis (advanced function set-
ting level): Page 235
185
sp-0 SP 0 The Number of Multi-SP Uses

parameter must be set to 1 or 2.
sp-1 SP 1 The Multi-SP Uses parameter must
be set to ON.
sp-2 SP 2
sp-3 SP 3
These parameters set the set points when the multi-SP function is used.
The values set in these parameters can be selected by operating the keys on
the front panel or by using event inputs.
When the set point has been changed, the set value of the set point (0 to
Function
3) selected by the multi-SP inputs is also changed to the same value.
The decimal point position depends on the selected sensor. During ana-
log input, it depends on the Decimal Point parameter setting.

SP lower limit to SP upper limit EU 0
Setting
Related Parameters
Input type (initial setting level): Page 200
Number of multi-SP uses: Page 213, Event input assignment 1 and 2 (initial
setting level): Page 216, Multi-SP uses: Page 220 (advanced function setting
level)
The Input Type parameter must be

set for a thermocouple or resistance
ins Temperature Input Shift thermometer, and the Input Shift
Type parameter must be set to a
one-point shift.
Sometimes an error occurs between the set point and the actual temperature.
To offset this, a compensated value can be obtained by adding an input shift
value to the input. The compensated value is displayed as the measurement
value and used for control.
The entire input range is shifted by a fixed rate (1-point shift). If the input shift
value is set to 1C, control will be performed for a value 1C lower than the
measured temperature.
Function

199.9 to 999.9 C or F 0.0
Setting
Related Parameters
See Input type (initial setting level): Page 200
Input shift type (advanced function setting level): Page 233
186
insh Upper-limit Temperature Input Shift Value The Input Type parameter must be
set for a thermocouple or resistance
thermometer and the Input Shift Type
insl Lower-limit Temperature Input Shift Value parameter must be set to a 2-point
shift, or the Input Type parameter
must be set for an infrared sensor.
These parameters are used to shift the input temperature at two points: an
upper-limit temperature and a lower-limit temperature (as opposed to the
Temperature Input Shift parameter, which shifts the input temperature by set-
ting the shift for only one point). A 2-point shift enables more accurate offset of
the input range compared with a 1-point shift if the input shift values at the
upper and lower limits differ.
This parameter sets input shift values for the upper and lower limits (2-point
shift) of the input range.
Function

199.9 to 999.9 C or F 0.0
Setting
Related Parameters
Input shift type (advanced function setting level): Page 233
187
p Proportional Band The control must be set to 2-PID

control.
i Integral Time
d Derivative Time
These parameters set PID control constants. PID constants are automatically
set when AT or ST is executed.
P action: Refers to control in which the MV is proportional to the deviation
(control error).
I action: Refers to a control action that is proportional to the time integral of
Function
the deviation. With proportional control, there is normally an offset
(control error). Proportional action is thus used in combination with
integral action. As time passes, this control error disappears, and
the control temperature (process value) comes to agree with the set
point.
D action: Refers to a control action that is proportional to the time derivative of
the control error. The proportional control and integral control cor-
rect for errors in the control result, and thus the control system is
late in responding to sudden changes in temperature. The derivative
action increases the MV in proportion to the slope of the change in
the temperature as a corrective action.
Parameter Models Setting range Unit Default
name
Setting Proportional Controllers with Thermocouple/ 0.1 to 999.9 C or F 8.0
Band Resistance Thermometer Multi- (See note
inputs 1.)
Controllers with Analog Inputs %FS 10.0
Integral Time 0 to 3999 Second 233
Derivative Time RT is OFF. 0 to 3999 Second 40
RT is ON. 0.0 to 999.9 Second 40.0
Note (1) Set None as the unit for Controllers with Analog Inputs.
(2) If the settings for RT (robust tuning) are changed, the proportional band
(P), integral time (I), and derivative time (D) will be initiated.
Related Parameters
See AT execute/cancel (adjustment level): Page 179
188
The control must be heating/cooling

c-sc Cooling Coefficient control and 2-PID control.
If the heating characteristics and cooling characteristics of the control object

are very different and good control characteristics cannot be achieved with the
same PID constants, the cooling coefficient can be used to adjust the propor-
tional band (P) for the control output assigned to the cooling side.
In heating/cooling control, the proportional band P for the cooling control
output is calculated using the following formula to set the cooling coeffi-
cient:
Function Cooling control output side P = Cooling coefficient P (proportional band)
When the Automatic Cooling Coefficient Adjustment parameter is set to
ON, the cooling coefficient is set automatically when AT is executed. If
there is strong non-linear gain for the cooling characteristics, however, it
may not be possible to obtain the optimum cooling coefficient at the Con-
troller.

0.01 to 99.99 None 1.00
Setting
Related Parameters
See Proportional band (adjustment level): Page 188
Automatic cooling coefficient adjustment (advanced function setting level):
Page 245
The control system must be set to

c-db Dead Band heating/cooling control.
This parameter sets the output dead band width for heating/cooling control. A
negative setting sets an overlapping band.
This parameter sets an area in which the control output is 0 centering
around the set point for a heating/cooling control.
Function
Model Setting range Unit Default

Controllers with Thermocouple/Resis- 199.9 to 999.9 C or F 0.0
tance Thermometer Universal Inputs (See note.)
Setting
Controllers with Analog Inputs 19.99 to 99.99 %FS 0.00
Note Set None as the unit for Controllers with Analog Inputs.
189
The control must be standard control

and 2-PID control.
of-r Manual Reset Value The Integral Time parameter must be
set to 0.
This parameter sets the required manipulated variable to remove offset

during stabilization of P or PD control.
Function

0.0 to 100.0 % 50.0
Setting
Related Parameters
See Integral time (adjustment level): Page 188
PID ON/OFF (initial setting level): Page 204
hys Hysteresis (Heating) The control must be ON/OFF control.

For the Hysteresis (Cooling) parame-
chys Hysteresis (Cooling) ter, the control must be heating/cool-
ing control.
This parameter sets the hysteresis for ensuring stable operation at the ON/
OFF switching point.
For standard control, use the Hysteresis (Heating) parameter. The Hyster-
esis (Cooling) parameter cannot be used.
For heating/cooling control, the hysteresis can be set independently for
Function
heating/cooling. The Hysteresis (Heating) parameter is used for the heat-
ing side, and the Hysteresis (Cooling) parameter is used for the cooling
side.
Parameter Model Setting range Unit Default

name
Setting Hysteresis Controllers with Thermocouple/Resistance 0.1 to 999.9 C or F 1.0
(Heating) Thermometer Universal Inputs (See note.)
Hysteresis Controllers with Thermocouple/Resistance 0.1 to 999.9 C or F 1.0
(Cooling) Thermometer Universal Inputs (See note.)
Controllers with Analog Inputs 0.01 o 99.99 %FS 0.10
Related Parameters
See PID ON/OFF, Standard or heating/cooling (initial setting level): Page 204
190

soak Soak Time must not be set to OFF.
This parameter sets the time for the control operation when using the sim-
ple program function.
Function
1 to 9999 min or h 1
Setting
Related Parameters
See Program start, Soak time remain (operation level): Page 171
Wait band (adjustment level): Page 191

wt-b Wait Band must not be set to OFF.
This parameter sets the stable band within which the soak time is mea-
sured for the simple program function.
Function
Model Setting range Unit Default

Controllers with Thermocouple/Resis- OFF or 0.1 to C or F off
tance Thermometer Universal Inputs 999.9 (See note.)
Setting Controllers with Analog Inputs OFF or 0.01 to %FS
99.99
Related Parameters
Soak time (adjustment level): Page 191
191

control.
mv-s MV at Stop The MV at Stop and Error Addition
parameter must be ON.
This parameter sets the MV to use when the RUN/STOP status changes
from RUN to STOP.
Function

5.0 to 105.0 for standard control % 0.0
105.0 to 105.0 (heating/cooling control)
Setting
Related Parameters
See RUN/STOP (operation level): Page 172
MV at stop and error addition (advanced function setting level): Page 233

control.
mv-e MV at PV Error The MV at Stop and Error Addition
parameter must be ON.
This parameter sets the MV to use when an input error occurs.
Function
5.0 to 105.0 for standard control % 0.0
105.0 to 105.0 (heating/cooling control)
Setting
Related Parameters
See MV at stop and error addition (advanced function setting level): Page 233
192
The ST parameter must be set to

sprt SP Ramp Set Value OFF.
This parameter sets the rate of change during SP ramp operation. Set the
maximum permissible change width per unit of time as the SP ramp set
value. The SP ramp function is disabled if this parameter is set to OFF.
Function
During temperature input, the decimal point position of the SP ramp set
value is dependent on the currently selected sensor, and during analog
input it is dependent on scaling.
OFF or 1 to 9999 EU/s, EU/minute, or off
EU/h
Setting
Related Parameters
(initial setting level): Page 202, ST: Page 205 (initial setting level)
SP ramp time unit (advanced function setting level): Page 220
ol-h MV Upper Limit The control must be set to 2-PID

control.
ol-l MV Lower Limit The ST parameter must be set to
OFF.
The MV Upper Limit and MV Lower Limit parameters set the upper and
lower limits of the manipulated variable. When the calculated manipulated
variable exceeds the upper or lower limit value, the upper or lower limit
Function value will be the output level.
MV Upper Limit
The setting ranges during standard control and heating/cooling control
are different.
Control method Setting range Unit Default

Standard MV lower limit + 0.1 to 105.0 % 105.0
Setting
Heating/cooling 0.0 to 105.0
MV Lower Limit
The setting ranges during standard control and heating/cooling control
are different. The manipulated variable for the cooling control output side
during heating/cooling control is expressed as a negative value.
Control method Setting range Unit Default
Standard 5.0 to MV upper limit 0.1 % 5.0
Heating/cooling 105.0 to 0.0 105.0
Related Parameters
See PID ON/OFF: Page 204, ST: Page 205 (initial setting level)
193
2-PID control must be used.

orl MV Change Rate Limit
ST must be OFF.
The MV Change Rate Limit parameter sets the maximum allowable varia-
tion in the MV per second. If the change in the MV exceeds this setting,
the MV will be changed by the MV change rate limit until the calculated
Function value is reached. If the limit is set to 0.0, this function will be disabled.
The MV Change Rate Limit parameter will not operate in the following sit-
uations.
In manual mode
During ST execution (Cannot be set when ST is ON.)
During AT execution
During ON/OFF control
While stopped (MV output during STOP)
During MV output when error occurs
0.0 to 100.0 %/s 0.0
Setting
Related Parameters
See Proportional band (adjustment level): Page 188
The input type must be an analog

input, and the Extraction of Square
sqrp Extraction of Square Root Low-cut Point Root Enable parameter must be set
to ON.
This parameter sets the extraction of square root low-cut point used for
the inputs. The data after extracting the square root is shown below.
The low-cut point is used for extracting the square root for flowrate sen-
Function
sors.
Operation result
100% FS
Extraction of square
root low-cut point
0 100% FS
Argument 1 (input data)

0.0 to 100.0 % 0.0
Setting
194
Related Parameters
See Extraction of square root enable (initial setting level): Page 216
195
Monitor/Setting Item Level Section 5-5
5-5 Monitor/Setting Item Level

Monitor/setting items can be displayed by means of the function key when the
PF Setting parameter (advanced function setting level) is set to PFDP: Moni-
tor/Setting Item (for the E5AN/EN only).
Power ON
Level Level
Press the O Key for
at least 1 s.
Monitor/Setting
PF Key PF Key
Item Level
Control in progress
The PF Setting parameter must be

set to PFDP, and the Monitor/Setting
Monitor/Setting Item Display 1 to 5 Item 1 to 5 parameters must not be
set to OFF.
When the PF Key is set to display monitor/setting items, pressing the PF

Key will display in order the contents of the Monitor/Setting Item 1 to 5
parameters. The contents of these parameters are shown in the following
Function table. For the setting (monitor) ranges, refer to the applicable parameters.
Set Setting Remarks
value Monitor/Setting Symbol
0 Disabled ---
1 PV/SP/Multi-SP Can be set. (SP) ---
2 PV/SP/MV Can be set. (SP) ---
3 PV/SP /Soak time remain Can be set. (SP) ---
Related Parameters
See PF setting (advanced function setting level): Page 247
Monitor/setting items 1 to 5 (advanced function setting level): Page 248
196
Manual Control Level Section 5-6
5-6 Manual Control Level

The manipulated variable can be set in manual mode while the PV/MV param-
eter is displayed.
The final MV used in automatic mode will be used as the initial manual MV
when moving from automatic mode to manual mode. In manual mode, the
change value will be saved immediately and reflected in the actual MV.
Power ON
Level Level
Press the O Key for
at least 1 s.
Press the O Key for at Press the PF Key

Press the PF Key for a-m least 1 s; display will flash.
at least 1 s or the O for at least 1 s. (See note.)
Key for at least 1 s. Press the O Key for
(See note.) at least 3 s.
Note: When the PF Setting parameter is
set to A-M for a Controller that has a
PF Key (E5AN/EN).
To move from the operation level to the manual control level, press the O Key
for at least three seconds with the Auto/Manual Switch parameter displayed.
In addition, this operation can be performed using the PF Key by setting the
PF Key parameter (advanced function setting level) to A-M (Auto/Manual). For
details on the setting method, refer to 4-13 Performing Manual Control.
This setting cannot be made during ON/OFF operation.
The MANU indicator will light during manual control.
It is not possible to move to any displays except for the PV/MV parameter
during manual operation.
To return to the operation level, press the O Key or the PF Key in the
manual control level for at least one second.
PV/MV (Manual MV)
The manual control level display appears as shown below.

With No. 3 Display
Without No. 3 Display
C C
Function 25 25 C
25
100 50.0
MANU
50.0
MANU 50.0 MANU
PV/Manual MV
PV/SP/Manual MV PV/Manual MV
Note: When the PV/SP Display Screen

Selection parameter is 0.
Monitor range Unit

each sensor.
Analog: Scaling lower limit 5% FS to Scaling
Set point SP lower limit to SP upper limit EU
197
Manual Control Level Section 5-6
Setting range Unit

MV (manual MV) Standard control 5.0 to 105.0 %
(See note.)
Heating/cooling control 105.0 to 105.0
(See note.)
Note When the Manual MV Limit Enable parameter is set to ON, the setting range
will be the MV lower limit to the MV upper limit.
Related Parameters
See Standard or heating/cooling (initial setting level): Page 204
198
Initial Setting Level Section 5-7
5-7 Initial Setting Level

This level is used to set up the basic Temperature Controller specifications. In
this level, you can set the Input Type parameter to set the sensor input to be
connected, limit the setting range of set points, set the alarm modes, and per-
form other operations.
Power ON
Operation
Level
Press the
C
Press the O Key

O Key
for at 25 Press the O Key for at
least 3 s.
for at least 1 s. least 1 s; 100
display
will flash. Control stops.
Initial Setting Control in progress

Level
Control stopped
To move from the operation level to the initial setting level, press the O Key
for at least three seconds with any parameter displayed except for the Auto/
Manual Switch parameter.
The initial setting level is not displayed when the Initial Setting/Communi-
cations Protect parameter is set to 2. It can be used when the Initial Set-
ting/Communications Protect parameter is set to 0 or 1.
If the Input Type parameter is set for an analog input, the following param-
eters will be set: Scaling upper limit, Scaling lower limit, and Decimal
point.
199
Page Page
in-t Input Type cp Control Period (Heating) 206 tr-l Transfer Output Lower 212
200 Limit
0.0
5 20
M
M M
in-h Scaling Upper Limit c-cp Control Period (Cooling) 206 o1-t Linear Current Output 212
202 4-20
100 20
M
M M
in-l Scaling Lower Limit oreV Direct/Reverse ev-m Number of Multi-SP 213
202 206 1 Uses
0 or-r Operation
M
M M
dp Decimal Point alt1 Alarm 1 Type ev-1 Event Input Assignment 216
202 207 1
none
0 2
M
M M
d-u Temperature Unit alh1 Alarm 1 Hysteresis ev-2 Event Input Assignment 216
202 209 2
stop
c 0.2
M
M M
C
sl-h SP Upper Limit alt2 Alarm 2 Type 209
sqr Extraction of Square 216
203 2 off Root Enable
1300
M
M M
amov Move to Advanced 217
C
sl-l SP Lower Limit 203 alh2 Alarm 2 Hysteresis 209 0 Function Setting Level
-200 0.2
M
M M
PIDON/OFF alt3 Alarm 3 Type
cntl 204 210
onof 2
M M
s-hc Standard or
Heating/Cooling 204 alh3 Alarm 3 Hysteresis 209
stnd 02
M M
st ST 205 tr-t Transfer Output Type 210
on off
M M
ptrn Program Pattern 205 tr-h Transfer Output Upper 212
off 100.0 Limit
M M
in-t Input Type
This parameter sets the type of sensor.

When this parameter is changed, the set point limiter is changed to the
defaults. If the limiter must be specified, set the SP Upper Limit and SP
Function
Lower Limit parameters (initial setting level) again.
Set one of the set values from the following table.
The defaults are as follows:
Controllers with Thermocouple/Resistance Thermometer Universal
Setting Inputs: 5 (K thermocouple)
Controllers with Analog Inputs: 0 (current input, 4 to 20 mA)
If a platinum resistance thermometer is mistakenly connected while a set-
ting for other than a platinum resistance thermometer is in effect, S.ERR
will be displayed. To clear the S.ERR display, check the wiring and then
cycle the power.
200
Input type Specifications Set value Input temperature range

Controllers Platinum resistance Pt100 0 200 to 850 (C)/300 to 1,500 (F)
with Ther- thermometer 1 199.9 to 500.0 (C)/199.9 to 900.0 (F)
mocouple/
Resistance 2 0.0 to 100.0 (C)/0.0 to 210.0 (F)
Thermome- JPt100 3 199.9 to 500.0 (C)/199.9 to 900.0 (F)
ter Multi- 4 0.0 to 100.0 (C)/0.0 to 210.0 (F)
inputs
Thermocouple K 5 200 to 1,300 (C)/300 to 2,300 (F)
6 20.0 to 500.0 (C)/0.0 to 900.0 (F)
J 7 100 to 850 (C)/100 to 1,500 (F)
8 20.0 to 400.0 (C)/0.0 to 750.0 (F)
T 9 200 to 400 (C)/300 to 700 (F)
10 199.9 to 400.0 (C)/199.9 to 700.0 (F)
E 11 200 to 600 (C)/300 to 1,100 (F)
L 12 100 to 850 (C)/100 to 1,500 (F)
U 13 200 to 400 (C)/300 to 700 (F)
14 199.9 to 400.0 (C)/199.9 to 700.0 (F)
N 15 200 to 1,300 (C)/300 to 2,300 (F)
R 16 0 to 1,700 (C)/0 to 3,000 (F)
S 17 0 to 1,700 (C)/0 to 3,000 (F)
B 18 100 to 1,800 (C)/300 to 3,200 (F)
Infrared Tempera- 10 to 70 (C) 19 0 to 90 (C)/0 to 190 (F)
ture Sensor 60 to 120 (C) 20 0 to 120 (C)/0 to 240 (F)
ES1B
115 to 165 (C) 21 0 to 165 (C)/0 to 320 (F)
140 to 260 (C) 22 0 to 260 (C)/0 to 500 (F)
Analog input 0 to 50 mV 23 One of the following ranges depending on the scal-
ing.
1,999 to 9,999
199.9 to 999.9
Thermocouple W 24 0 to 2,300 (C)/0 to 3,200 (F)
PLII 25 0 to 1,300 (C)/0 to 2,300 (F)
Input type Specifications Set value Input temperature range

Controllers Current input 4 to 20 mA 0 One of the following ranges depending on the scal-
with Ana- 0 to 20 mA 1 ing.
log Inputs 1,999 to 9,999
Voltage input 1 to 5 V 2 199.9 to 999.9
0 to 5 V 3 19.99 to 99.99
0 to 10 V 4 1.999 to 9.999
Related Parameters
See Temperature unit, Set point upper limit, Set point lower limit (initial setting
level): Page 202
201
in-h Scaling Upper Limit The input type must be set for an
analog input.
in-l Scaling Lower limit
dp Decimal Point
These parameters can be used when the input type is set for an analog
input.
When an analog input is used, scaling is performed. Set the upper limit in
Function
the Scaling Upper Limit parameter and the lower limit in the Scaling Lower
Limit parameter.
The Decimal Point parameter specifies the decimal point position of
parameters (set point, etc.) whose unit is EU.
Scaling Upper Limit, Scaling Lower Limit
Scaling Upper Limit Scaling lower limit + 1 to 9999 None 100
Setting
Scaling Lower Limit 1999 to scaling upper limit 1 None 0
Decimal Point
Parameter Model Setting Default
name range
Decimal Point Controllers with Thermocouple/Resis- 0 to 1 0
tance Thermometer Universal Inputs
Controllers with Analog Inputs 0 to 3 0
Set value Settings Example

0 0 digits past decimal point 1234
1 1 digits past decimal point 123.4
Related Parameters
The input type must be set for a tem-

d-u Temperature Unit perature input.
Set the temperature input unit to either C or F.
Function

c: C, f: F c
Setting
Related Parameters
202
sl-h SP Upper Limit

sl-l SP Lower Limit
These parameters set the upper and lower limits of the set points. A set
point can be set within the range defined by the upper and lower limit set
values in the SP Upper Limit and SP Lower Limit parameters. If these
Function parameters are reset, any set point that is outside of the new range will be
forcibly changed to either the upper limit or the lower limit.
When the temperature input type and temperature unit have been
changed, the set point upper limit and set point lower limit are forcibly
changed to the upper and lower limits of the sensor.
Controllers with Thermocouple/Resistance Thermometer Universal Inputs
Parameter Setting range Unit Default
name
Setting Set Point Temperature SP lower limit + 1 to Input set- EU 1300
Upper Limit ting range upper limit
Analog SP lower limit + 1 to scaling EU 100
upper limit
Set Point Temperature Input setting range lower limit EU 200
Lower Limit to SP upper limit 1
Analog Scaling lower limit to SP EU 0
upper limit 1
Controllers with Analog Inputs

Set Point Upper Limit SP lower limit + 1 to scaling upper EU 100
limit
Set Point Lower Limit Scaling lower limit to SP upper EU 0
limit 1
Related Parameters
See Input type: Page 200, Temperature unit: Page 202 (initial setting level)
203
cntl PID ON/OFF
This parameter selects 2-PID control or ON/OFF control.

The auto-tuning and self-tuning functions can be used in 2-PID control.
Function

pid: 2-PID, onof: ON/OFF onof
Setting
Related Parameters
See AT execute/cancel: Page 179, Manual reset value, Hysteresis (heating), and
Hysteresis (cooling): Page 190 (adjustment level)
ST stable range (advanced function setting level): Page 224
s-hc Standard or Heating/Cooling
This parameter selects standard control or heating/cooling control.

When heating/cooling control is selected for the E5CN or E5CN-U, the
auxiliary output 2 terminal (SUB2) is assigned as the control output (cool-
Function
ing).
When heating/cooling control is selected for the E5AN or E5EN, the auxil-
iary output 3 terminal (SUB3) is assigned as the control output (cooling).
When heating/cooling control is selected for the E5GN, the auxiliary out-
put 1 terminal (SUB1) is assigned as the control output (cooling).
Note If standard control is selected, set the Control Output 1 Assignment to o (con-
trol output (heating)) for either direct (cooling) or reverse (heating) operation.

stnd: Standard, h-c: Heating/cooling stnd
Setting
Related Parameters
See MV monitor (heating): Page 175, MV monitor (cooling): Page 176 (operation
level)
Cooling coefficient, Dead band: Page 189, Hysteresis (heating), Hysteresis
(cooling): Page 190 (adjustment level)
Control period (heat), Control period (cool) (initial setting level): Page 206
Control output 1 assignment: Page 238, Control output 2 assignment, Auxil-
iary output 1 assignment: Page 240, Auxiliary output 2 assignment: Page 241,
Auxiliary output 3 assignment: Page 242 (advanced function setting level)
204
The control must be set to a temper-

st ST (self-tuning) ature input, standard control, and 2-
PID control.
The ST (self-tuning) function executes tuning from the start of program

execution to calculate PID constants matched to the control target. When
the ST function is in operation, be sure to turn ON the power supply of the
Function load connected to the control output simultaneously with or before starting
Controller operation.
Auto-tuning can be started during self-tuning.

ST off: ST function OFF, on: ST None on
function ON
Setting
Related Parameters
See Input type: Page 200, PID ON/OFF: Page 204 (initial setting level), ST stable
range (advanced function setting level): Page 224
ptrn Program Pattern
This parameter sets the type of control when using the simple program func-
tion.
If the program pattern is set to off, the simple program will not operate.
If the program pattern is set to stop, the RUN/STOP status will change to
STOP after the soak time has expired. If the program pattern is set to
Function
cont, control will continue in RUN status after the soak time has expired.

off Simple program function turned OFF off
stop Go to STOP mode at end of program.
Setting
cont Continue in RUN mode at end of program.
Related Parameters
See Program start, Soak time remain: Page 171, RUN/STOP: Page 172 (operation
level)
205
The cooling control output and heat-

ing control output must be assigned
cp Control Period (Heating) to relay or voltage outputs (for driving
SSR).
control.
c-cp Control Period (Cooling) For the Control Period (Cooling)
parameter, the control must be set to
heating/cooling control.
These parameters set the output periods. Set the control periods taking
the control characteristics and the electrical durability of the relay into
consideration.
Function
For standard control, use the Control Period (Heating) parameter. The
Control Period (Cooling) parameter cannot be used.
When the heating control output is a current output, the Control Period
(Heating) parameter cannot be used.
For heating/cooling control, the control period can be set independently
for heating and cooling. The Control Period (Heating) parameter is used
for the heating control output, and the Control Period (Cooling) parameter
is used for the cooling control output

Control Period (Heating) 0.5 or 1 to 99 Second 20
Control Period (Cooling) 0.5 or 1 to 99 Second 20
Setting
Related Parameters
See PID ON/OFF (initial setting level): Page 204
orev Direct/Reverse Operation
Direct operation refers to control where the manipulated variable is

increased when the process value increases. Alternatively, reverse oper-
ation refers to control where the manipulated variable is increased when
Function the process value decreases.

or-r: Reverse operation, or-d: Direct operation or-r
Setting
206
alt1 Alarm 1 Type Alarm 1 must be assigned.
Select one of the following alarm 1 types:

Deviation, deviation range, absolute value, LBA, or PV change rate alarm.
Function
Setting

0 Alarm function OFF Output OFF No alarm
ON
1.) OFF setting the alarm upper limit (H)
SP
2 Upper-limit X X Set the upward deviation in the set
ON ON
OFF OFF point by setting the alarm value
SP SP
(X).
3 Lower-limit X X Set the downward deviation in the
ON ON
OFF OFF set point by setting the alarm value
SP SP
(X).
ON
1.) range OFF setting the alarm upper limit (H)
SP
5 (See note Upper- and lower-limit L H See note 4. A standby sequence is added to
ON
1.) with standby sequence OFF
SP
the upper- and lower-limit alarm
See note 5. (1). (See note 6.)
6 Upper-limit with standby X X A standby sequence is added to

ON ON
sequence OFF OFF the upper-limit alarm (2). (See note
SP SP
6.)
7 Lower-limit with standby X X A standby sequence is added to
ON ON
sequence OFF OFF the lower-limit alarm (3). (See note
SP SP
6.)
8 Absolute-value upper- X X The alarm will turn ON if the pro-
ON ON
limit OFF OFF cess value is larger than the alarm
0 0
value (X) regardless of the set
point.
9 Absolute-value lower-limit X X The alarm will turn ON if the pro-
ON ON
OFF OFF cess value is smaller than the
0 0
alarm value (X) regardless of the
set point.
10 Absolute-value upper- X X A standby sequence is added to
ON ON
limit with standby OFF OFF the absolute-value upper-limit
0 0
sequence alarm (8). (See note 6.)
11 Absolute-value lower-limit X X A standby sequence is added to
ON ON
with standby sequence OFF OFF the absolute-value lower-limit
0 0
alarm (9). (See note 6.)
12 LBA (alarm 1 type only) --- Refer to page 118. (See note 7.)
13 PV change rate alarm --- Refer to page 72. (See note 8.)
207
Note (1) With set values 1, 4 and 5, the upper- and lower- limit values can be set
independently for each alarm type, and are expressed as L and H.
(2) Set value: 1 (Upper- and lower-limit alarm)
Case 1 Case 2 Case 3 (Always ON)
H < 0, L < 0
H < 0, L > 0
H < 0, L > 0 H > 0, L < 0
H L SP |H| |L|
|H| < |L| |H| > |L|
H > 0, L < 0
SP H L |H| |L|
(3) Set value: 4 (Lower limit range)

Case 1 Case 2 Case 3 (Always OFF)
H < 0, L < 0
H < 0, L > 0 H > 0, L < 0 H < 0, L > 0
|H| < |L| |H| > |L| H L SP |H| |L|
H > 0, L < 0
SP H L |H| |L|

For the lower-limit alarms in cases 1 and 2 above, the alarm is normal-
ly OFF if upper- and lower-limit hysteresis overlaps.
In case 3, the alarm is always OFF.
(5) Set value: 5 (The alarm is always OFF if upper- and lower-limit alarm hys-
teresis with standby sequence overlaps.)
(6) Refer to 4-2-1 Standby Sequence for information on the operation of the
standby sequence.
(7) Refer to 4-12-1 Loop Burnout Alarm (LBA)
(8) Refer to PV Change Rate Alarm on page 72.
Set the alarm type independently for each alarm in the Alarm 1 to 3 Type
parameters in the initial setting level. The default is 2 (Upper-limit alarm).
Related Parameters
See Alarm value 1: Page 172, Alarm value upper limit 1, Alarm value lower limit 1:
Page 174 (operation level)
Standby sequence reset: Page 221, Auxiliary output 1 open in alarm: Page
222, Alarm 1 latch: Page 227 (advanced function setting level), Alarm 1 hys-
teresis: Page 209 (initial setting level)
208

alh1 Alarm 1 Hysteresis The alarm 1 type must not be 0, 12,
or 13.
or 13.
or 13.
These parameters set the hysteresis for alarms 1, 2, and 3.
Function
Models Setting range Unit Default

Model with thermocouple/resis- 0.1 to 999.9 C or F 0.2
Setting tance thermometer universal (See note.)
input
Model with analog Input 0.01 to 99.99 %FS 0.02
Note Set None as the unit for analog inputs.
Related Parameters
See Alarm value 1 to 3: Page 173, Alarm value upper limit 1 to 3, Alarm value
lower limit 1 to 3: Page 174 (operation level)
Alarm 1 to 3 type (initial setting level): Pages 207 to 210
Standby sequence reset: Page 221, Auxiliary output 1 to 3 open in alarm:
Page 222, Alarm 1 to 3 latch: Page 227 (advanced function setting level)
Select one of the following four alarm 2 types:

Deviation, deviation range, absolute value, or PV change rate alarm.
Function
Refer to the alarm 1 type list. The 12: LBA (Loop Burnout Alarm) setting in
that list cannot be used.
Setting
Related Parameters
tion setting level)
209
Select one of the following four alarm 3 types:

Deviation, deviation range, absolute value, or PV change rate alarm.
Function
Refer to the alarm 1 type list. The 12: LBA (Loop Burnout Alarm) setting in
that list cannot be used.
Setting
Related Parameters
tion setting level)
There must be a transfer output or a

tr-t Transfer Output Type current output.
This parameter sets the transfer output type.

The operation is shown in the following table.
Transfer Output Destination
Control output 1 Control output 2 Transfer output
destination
Current output No Control output 1
Relay output
Voltage output (for driving
SSR)
Relay output No No
Voltage output (for driving Relay output
SSR) Voltage output (for driving
SSR)
Precision and User Calibration

Precision User calibration
Transfer output 0.3% FS Supported (See note.)
Simple transfer output 0.3% FS Not supported.
Note Refer to SECTION 6 CALIBRATION for details on the calibration procedure.
210
Transfer output type Default

OFF off off
Setting Set point sp
Set point during SP ramp sp-m
PV pv
MV monitor (heating) mv
MV monitor (cooling) c-mv
]
Related Parameter
See Transfer output upper limit, Transfer output lower limit (initial setting level):
Page 212
211
tr-h Transfer Output Upper Limit There must be a transfer output or a

current output.
tr-l Transfer Output Lower Limit The transfer output type must not be
set to OFF.
This parameter sets the upper and lower limit values of transfer outputs.
Function
Transfer output Setting range Default Unit
type Transfer Transfer
output lower output upper
limit limit
Setting
Set point SP lower limit to SP upper limit SP lower limit SP upper limit EU
Set point during SP lower limit to SP upper limit
SP ramp
PV Temperature Input setting range lower limit Input setting Input setting
to input setting range upper range lower range upper
limit limit limit
Analog Analog scaling lower limit to Scaling lower Scaling upper
analog scaling upper limit limit limit
MV monitor Standard 5.0 to 105.0 0.0 100.0 %
(heating) Heating/ 0.0 to 105.0
cooling
MV monitor 0.0 to 105.0
(cooling)
Related Parameter
See Transfer output type (initial setting level): Page 210
Control output 1 must be a current

o1-t Linear Current Output output.
This parameter selects the output type for linear current outputs.
Linear current Default

output
Setting 4-20: 4 to 20 mA 4-20
0-20: 0 to 20 mA
Note Even when control output 1 is used as a control output or a simple transfer
output, 0 to 20 mA can be used.
Related Parameter
See Transfer output type (initial setting level): Page 210
212
ev-m Number of Multi-SP Uses An event input must be assigned.
Multi-SP is a function for setting set points 0 to 3 in advance, and switch-

ing between these set points using a combination of event input ON/OFF
signals.
Function The Number of Multi-SP Uses parameter is used to switch between using
two and four preset set points.

0 to 2 1
Setting
Whether the Event Input Assignments 1 and 2 parameters are displayed
or hidden is determined by the Number of Multi-SP Uses parameter set-
ting.
operation
Number of multi- 0 Displayed (Multi-SP not used). EV1 and EV2 will perform the
SP uses operation command assigned
points.) set points 0 and 1. EV2 will per-
assigned using the Event Input
Assignment 2 parameter.
between set points 0, 1, 2, and
3.
The following tables show the relationships between ON/OFF combinations of

event inputs 1 and 2 and selected set points.
Number of Multi-SP Uses: 1:
Even input 1 Selected set point
OFF Set point 0
ON Set point 1
Number of Multi-SP Uses: 2

Even input 1 Even input 2 Selected set point
OFF OFF Set point 0
ON OFF Set point 1
OFF ON Set point 2
ON ON Set point 3
213

operation
Number of multi- 0 Displayed (Multi-SP not used). EV3 and EV4 will perform the
SP uses operation command assigned
parameter.
and 3.

OFF Set point 0
ON Set point 1

OFF OFF Set point 0
ON OFF Set point 1
OFF ON Set point 2
ON ON Set point 3
Models with Four Event Inputs, 1 to 4

Event input Event input Event input Event input Description of EV1, EV2,
assignment 1 assignment 2 assignment 3 assignment 4 EV3, and EV4 operation
Number of Multi- 0 Displayed (Multi-SP not used). EV1, EV2, EV3, and EV4 will
SP Uses perform the operation com-
Event Input Assignment 1, 2,
3, and 4 parameters.
1 Not displayed Displayed (Event inputs 2, 3, and 4 cannot be EV1 will be used for the Multi-
(Operation used for multi-SP switching.) SP function to switch between
performed set points 0 and 1. EV2, EV3,
with two Multi- and EV4 will perform the
SP points.) operation command assigned
ment 2, 3, and 4 parameters.
2 Not displayed (Operation per- Displayed (Event inputs 3 and EV1 and EV2 will be used for
formed with four Multi-SP 4 cannot be used for multi-SP the Multi-SP function to switch
points.) switching.) between set points 0, 1, 2,
and 3. EV3 and EV4 will per-
assigned using the Event
Input Assignment 3 and 4
parameters.
Only event inputs 1 and 2 are used for the multi-SP function.
214

OFF Set point 0
ON Set point 1

OFF OFF Set point 0
ON OFF Set point 1
OFF ON Set point 2
ON ON Set point 3
The following table shows the functions assigned when an Event Input
Assignment (1 or 2) is displayed.
Setting Function
none None
stop RUN/STOP
manu Auto/Manual Switch
prst Program start (See note 1.)
be disabled.
When any of the following functions is set for an Event Input Assignment
parameter, the same function cannot be set for another Event Input
Assignment parameter: STOP (RUN/STOP), MANU (Auto/Manual
Switch), PRST (Program Start), DRS (Invert Direct/Reverse Operation),
AT-2 (100% AT Execute/Cancel), AT-1 (40% AT Execute/Cancel), WTPT
(Setting Change Enable/Disable), or LAT (Alarm Latch Cancel).
Note Event inputs can be used on the E5CN-@M@ (with an E53-CN@B@N2) or
E5AN/EN-@M@-N (with an E53-AKB) Controllers. Turn event inputs ON and
OFF while the power is being supplied. Event input ON/OFF changes are
detected for inputs of 50 ms or longer.
Related Parameter
See SP0 to SP3 (adjustment level): Page 186
Event input assignment 1 and 2: Page 216 (initial setting level), Multi-SP use:
Page 220 (advanced function setting level)
215
An event input must be assigned.

ev-* Event Input Assignment * (*: 1 and 2)
Multi-SP must not be used.
The following functions can be assigned to event inputs 1 and 2.

RUN/STOP
Function Auto/Manual Switch
Program Start
Invert Direct/Reverse Operation
100% AT Execute/Cancel
40% AT Execute/Cancel
Setting Change Enable/Disable
Alarm Latch Cancel
Default: Event Input Assignment 1: none
Event Input Assignment 2: stop
Setting Function
none None
stop RUN/STOP
Setting
manu Auto/Manual
prst Program start (See note 1.)
be disabled.
Related Parameter
See SP0 to SP3 (adjustment level): Page 186
Number of multi-SP uses (initial setting level): Page 213
sqr Extraction of Square Root Enable An analog input must be supported.
This parameter enables and disables square root extraction.
Function

on: Enabled, off: Disabled OFF
Setting
216
Related Parameter
See Extraction of square root low-cut point (adjustment level): Page 194
The Initial Setting/Communications

amov Move to Advanced Function Setting Level Protect parameter must be set to 0.
Set the Move to Advanced Function Setting Level parameter set value to
169.
Move to the advanced function setting level either by pressing M Key or
Function
O Key or by waiting or two seconds to elapse.
Related Parameter
See Initial setting/communication protect (protect level): Page 160
217
Advanced Function Setting Level Section 5-8
5-8 Advanced Function Setting Level

The advanced function setting level is used for optimizing Controller perfor-
mance. To move to this level, input the password (169) from the initial set-
ting level.
To be able to enter the password, the Initial Setting/Communications Protect
parameter in the protect level must be set to 0.
The parameters in this level can be used when the Initial Setting/Commu-
nications Protect parameter is set to 0.
To switch between setting levels, press the O Key.
To change set values, press the U and D Keys.
Power ON
Level Level
Press the
Press the
O Key C
Press the O Key
for at least 1 s. for at 25 Press the O Key for at
least 3 s.
least 3 s. 100
Control stops.
Communi-
Initial Setting cations
Level Setting
Press the Level
O Key for less than 1 s.
Press the O Key Password input

for at least 1 s. set value 169
Advanced Function Control in progress

Setting Level Control stopped
218
Advanced Function Setting Level
M
Heater
init Parameter
220 a1lt Alarm 1 Latch 227 hsu HS Alarm Use 235 och Overcurrent 247
off Initialization off on 0.1
Hysteresis
M M M M
mspu Multi-SP Uses a2lt Alarm 2 Latch hsl HS Alarm Latch pf PF Setting
220 227 235 247
off off off a-m
M M M M
spru SP Ramp Time 220 a3lt Alarm 3 Latch 227 hsh HS Alarm 236 pfd1 Monitor/Setting 248
m Unit off 0.1 Hysteresis 1 Item 1
M M M M
rest Standby
Sequence 221 prlt Move to Protect 228 lba LBA Detection 236 pfd2 Monitor/Setting 248
a 3 Level Time 0 Time 0 Item 2
Reset
M M M M
sb1n Auxiliary Output 222 sero Input Error 228

C
lbal LBA Level 237 pfd3 Monitor/Setting 248
n-o 1 Open in Alarm off Output 8.0 0 Item 3
M M
M M M
Cold Junction
sb2n Auxiliary Output 222 cjc Compensation 229 C
lbab LBA Band 237 pfd4 Monitor/Setting 248
n-o 2 Open in Alarm on 3.0 0 Item 4
Method
M M M M
sb3n Auxiliary Output 222 rlrv MB Command 229 out1 Control Output 1 238 pfd5 Monitor/Setting 248
n-o 3 Open in Alarm off Logic Switching o Assignment 0 Item 5
M M M M
hbu HB ON/OFF 222 colr PV Change 230 out2 Control Output 2 239 spdp PV/SP Display
on red Color Assignment
none 4 Screen Selection 249
M M M M
pv-b PV Stable sub1 Auxiliary Output 1 240

c
hbl Heater Burnout 231 odsl MV Display 249

offLatch 223 5.0 Band alm1 Assignment o Selection
M M M
M
hbh Heater Burnout a1on Alarm 1 ON 232 sub2 Auxiliary Output 2 241 pvdp PV Decimal 250
0.1 Hysteresis 223 0 Delay alm2Assignment on Point Display
M M M M
C
st-b ST Stable a2on Alarm 2 ON 232 sub3 Auxiliary Output 3 242 pvst PV Status 250
Range 224 0 Delay alm3 Assignment off Display Function
15.0
M M M M
alfa 224 a3on Alarm 3 ON

0 Delay
232 csel Character
Select 243
svst SV Status
Display Function
251
0.65 on off
M M M M
at-g AT Calculated a1of Alarm 1 OFF 232 t-u Soak Time Unit 243 d.ref Display Refresh 251
0.8 Gain 225 0 Delay m 0.25Period
M M M M
Control Output 1
C
at-h AT Hysteresis 225 a2of Alarm 2 OFF alsp Alarm SP 244 ra1m ON/OFF Count 252
0 Delay 232 sp-m Selection 0
0.8 Monitor
M M M M
Control Output 2
lcma Limit Cycle MV a3of Alarm 3 OFF 232 manl Manual MV Limit 244 ra2m ON/OFF Count 252
225 0 Delay
20.0 Amplitude off Enable 0
Monitor
M M M
M
inf Input Digital 226 istp Input Shift Type 233 pvrp PV Rate of ra1 Control Output 1
0.0 Filter in51 Change Calculation 245 0 ON/OFF Count 253
4
M M M Period M Alarm Set Value
pvad Additional PV mvse MV at Stop and csca Automatic Cooling 245 ra2 Control Output 2 253
Display 226 off Error Addition 233 0ON/OFF Count
off offCoefficient
M M
M Adjustment M Alarm Set Value
o-dp MV Display 227 amad Auto/Manual 234 ocu Heater rac ON/OFF Counter 254
off off Select Addition 246 0 Reset
onOvercurrent
M M M
M Use
ret Automatic 227 rt RT
234 ocl Heater 246 cmov Move to 254
Display Return off 0 Calibration Level
off off Overcurrent
Time M M
M M Latch
219
init Parameter Initialization
This parameter returns all parameter settings to their defaults.

After the initialization, the set value automatically turns off.
Function

off: Initialization is not executed. off
fact: Initializes to the factory settings described in the manual.
Setting
The model must not support event

mspu Multi-SP Uses inputs, or the number of multi-SP
uses must be 0.
This parameter enables switching between set points 0 to 3 by operating the

keys on the front panel.
Prerequisites
Function
A model without event inputs
The Number of Multi-SP Uses parameter set to 0 on a model with event
inputs
on: Set points 0 to 3 can be selected.
off: Set points 0 to 3 cannot be selected.
Default: OFF
Setting
Related Parameters
See Multi-SP set point setting (operation level): Page 167
Number of multi-SP uses (Initial setting level): Page 213
The ST parameter must be set to

spru SP Ramp Time Unit OFF.
This parameter sets the time unit for the rate of change during SP ramp
operation.
Function
s: EU/s, m: EU/min, h: EU/h m
Setting
Related Parameters
See Ramp SP monitor (operation level): Page 167
SP ramp set value (adjustment level): Page 193
220
Alarm 1 to 3 type must be 5, 6, 7, 10,

rest Standby Sequence Reset or 11.
This parameter selects the conditions for enabling reset after the standby
sequence of the alarm has been canceled.
Output is turned OFF when switching to the initial setting level, communi-
Function
cations setting level, advanced function setting level, or calibration level.
Condition A
Control started (including power ON), and set point, alarm value (alarm
value upper/lower limit), or input shift value (upper/lower-limit temperature
input shift value) changed.
Condition B
Power ON
The following example shows the reset action when the alarm type is
lower-limit alarm with standby sequence.
Condition A only
SP change
Alarm
(after change)
Alarm hysteresis
Condition A : Standby sequence canceled

only : Standby sequence reset
Alarm
Alarm output:
Condition A
Alarm output:
Condition B

a: Condition A, b: Condition B a
Setting
Related Parameters
See Alarm 1 to 3 type (initial setting level): Page 207 to 209
Alarm 1 to 3 latch (advanced function setting level): Page 227
221
Auxiliary Output * Open in Alarm Auxiliary output 1, 2, or 3 must be

sb*n assigned.
(*: 1 to 3)
This parameter sets the output status of auxiliary outputs 1 to 3.

When Close in Alarm is set, the status of the auxiliary output function is
output unchanged. When Open in Alarm is set, the status of the auxiliary
Function
output function is reversed before being output. The following table shows
the relationship between the auxiliary output function, auxiliary output,
and operation displays (SUB1 to SUB3).
Auxiliary output Auxiliary output Operation display

function (SUB1 to SUB3)
Close in Alarm ON ON Lit
Setting OFF OFF Not lit
Open in Alarm ON OFF Lit
OFF ON Not lit

n-o: Close in alarm, n-c: Open in alarm n-o
Related Parameters
See Auxiliary output 1 to 3 assignment (advanced function setting level): Pages
240 to 242

hbu HB ON/OFF supported.
Set to use the heater burnout alarm.
Function
Setting
222

supported.
hbl Heater Burnout Latch Alarm 1 must be assigned.
The Heater Burnout Detection
parameter must be set to ON.
When this parameter is set to ON, the heater burnout alarm is held until
either of the following conditions is satisfied.
a Heater burnout detection is set to 0.0 A.
Function
b The power is cycled.
c The latch is cancelled by the PF Key.
(PF Setting = LAT: Alarm Latch Cancel)
d The latch is cancelled by an event input.
(Event Input Assignment 1 and 2 = LAT: Alarm Latch Cancel)

on: Enabled, off: Disabled off
Setting
Related Parameters
See Event input assignment 1 and 2 (initial setting level): Page 216
HB ON/OFF: Page 222, PF setting: Page 247 (advanced function setting
level)
The Heater Burnout parameter must

be set to ON.
The Heater Burnout Latch parameter
must be set to OFF.
hbh Heater Burnout Hysteresis Heater burnout, HS alarms, and
supported.
This parameter sets hysteresis for heater burnout detection.
Function
0.1 to 50.0 A 0.1
Setting
Related Parameters
See HB ON/OFF (advanced function setting level): Page 222
223
ST must be ON and temperature

st-b ST Stable Range input, standard control, 2-PID control
must be set.
The setting of this parameter determines when ST operates.

This parameter cannot be used when ST is set to OFF.
Function

0.1 to 999.9 C or F 15.0
Setting
Related Parameters
See Input type: Page 200, PID ON/OFF: Page 204, ST: Page 205 (initial setting
level)
ST must be OFF and 2-PID control

alfa must be set.
Normally, use the default for this parameter.

This parameter sets the 2-PID control constant.
Function

0.00 to 1.00 None 0.65
Setting
Related Parameters
See PID ON/OFF: Page 204, ST: Page 205 (initial setting level)
224
at-g AT Calculated Gain Control must be set to 2-PID control.
at-h AT Hysteresis
lcma Limit Cycle MV Amplitude
Normally use the default values for these parameters.

The AT Calculated Gain parameter sets the gain for when PID values are
calculated using AT. When emphasizing response, decrease the set
Function
value. When emphasizing stability, increase the set value.
The AT Hysteresis parameter sets the hysteresis for limit cycle operation
during autotuning when switching ON and OFF.
The Limit Cycle MV Amplitude parameter sets the MV amplitude for limit
cycle operation during autotuning.

AT Calculated Gain 0.1 to 10.0 --- 0.8
AT Hysteresis Universal input: C or F 0.8 (See note.)
Setting 0.1 to 999.9
Analog input: %FS 0.20
0.01 to 9.99
Limit Cycle MV 5.0 to 50.0 % 20.0
Amplitude
Note When the temperature unit is F, the default is 1.4.
Related Parameters
See AT execute/cancel (adjustment level): Page 179
225
inf Input Digital Filter
This parameter sets the time constant for the input digital filter. The follow-
ing diagram shows the effect on data after passing through the digital fil-
ter:
Function
PV before passing through filter
A
PV after passing through filter
0.63 A
(Time
constant) Time
Input digital filter

0.0 to 999.9 Second 0.0
Setting
pvad Additional PV Display
This parameter adds a display at the beginning of the operation level for the
process value (PV). If there is no need to display the set point, use this to dis-
play only the present temperature.
Function
Set to ON to display, and OFF to not display.

on: Displayed, off: Not displayed off
Setting
226
o-dp MV Display
This parameter is used to display the manipulated variable (MV).

The manipulated variable is displayed when the MV Monitor (Heating) and MV
Monitor (Cooling) parameters are set to ON, and not displayed when these
parameters are set to OFF.
Function

Setting
Related Parameters
See MV monitor (heating): Page 175, MV monitor (cooling): Page 176 (operation
level)
ret Automatic Display Return Time
In the operation level, adjustment level, or monitor/setting item level, the

display automatically returns to the PV/SP if there are no key operations
for the time set for this parameter.
Function
The automatic display return time is disabled when the parameter is set to
OFF. (In that case, the display will not be automatically switched.)
OFF, 1 to 99 Second off
Setting
Alarm 1 must be assigned, and the

a1lt Alarm 1 Latch alarm 1 type must not be 0.
a2lt Alarm 2 Latch alarm 2 type must not be 0 or 12.
a3lt Alarm 3 Latch alarm 3 type must not be 0 or 12.
When this parameter is set to ON, the alarm function is held until one of
the following conditions is satisfied.
a The power is cycled.
Function
b The latch is cancelled by the PF Key.
c The latch is cancelled by an event input.
227
The output is turned OFF when switching to the initial setting level, com-
munications setting level, advanced function setting level, or calibration
level.
If an auxiliary output is set to close in alarm, the output is kept closed. If it
is set to open in alarm, it is kept open.
Setting
Related Parameters
See Alarm value 1 to 3: Page 172 to 173, Alarm value upper limit 1 to 3: Page 174
to 175, Alarm value lower limit 1 to 3: Page 174 to 175 (operation level)
Alarm 1 to 3 type (initial setting level): Page 207 to 210
Standby sequence reset: Page 221, Auxiliary output 1 to 3 open in alarm:
Page 222 (advanced function setting level), Alarm 1 to 3 hysteresis: Page 209
(initial setting level)
Event input assignment 1 and 2 (initial setting level): Page 216
level)
prlt Move to Protect Level Time
This parameter sets the key pressing time required to move to the protect
level from the operation level, the adjustment level, or monitor/setting item
level.
Function

1 to 30 Second 3
Setting
Related Parameters
See Operation/adjustment protect, Initial setting/communications protect, Setting
change protect (protect level): Page 160
Alarm 1 must be assigned, but not to

sero Input Error Output a work bit output.
When this parameter is set to ON, the output assigned for alarm 1 turns
ON for input errors.
Note For details on input errors, refer to Error Displays on page 281.
Function
The alarm 1 output is an OR output of alarm 1, HB alarm/HS alarm,
heater overcurrent alarm, and input error.
Setting
228

Input type must be thermocouple or

cjc Cold Junction Compensation Method infrared temperature sensor
This parameter specifies whether cold junction compensation is to be per-

formed internally by the Controller or to be performed externally when the
input type setting is 5 to 22, 24, or 25.
Function
The cold junction compensation external setting is enabled when the tem-
perature difference is measured using two thermocouples or two ES1B
Sensors.

on: Internally, off: Externally on
Setting
Related Parameters
Communications must be supported.

rlrv MB Command Logic Switching CompoWay/F must be selected as
the protocol.
This parameter switches the logic of the MB command (communications

writing switch) for the SYSWAY communications protocol
The MB command (communications writing switch) is the equivalent of
Function
the MB command (remote/local switch) of the E5@J.
The setting indicated by the shaded cell indicates the default (same logic
as E5@J).
Set Text data of MB command
Setting value 0000 0001
OFF Communications writing enabled Communications writing disabled
(remote mode selection) (local mode selection)
ON Communications writing disabled Communications writing enabled
(local mode selection) (remote mode selection)
(Terms in parentheses () are the terms used on the E5@J.)
Related Parameters
See Communications writing (adjustment level): Page 180
Protocol setting (communications setting level): Page 255
229
colr PV Change Color
Use the PV color change function to change the color of the PV display (No. 1
display).
There are three display colors, orange, red, and green, and you can select
Function
from the following three modes and eight types.
Constant: This mode displays orange, red, or green all the time.
Linked to Alarm 1: This mode switches the PV display color from red to
green when alarm 1 turns ON or from green to red when alarm 1 turns
ON.
Linked to PV stable band: This mode switches the PV display color
between red outside the PV stable band and green within PV stable band,
or between green outside the PV stable band and red within PV stable
band. Set the PV stable band in the PV Stable Band parameter in the
advanced function setting level.
The default is red (red).
The following table shows the display functions that can be set using the PV
color change function.
Constant org Orange Constant: Orange To match the display color
Setting red Red Constant: Red To match the display color
grn Green Constant: Green To match the display color
Linked to Alarm
alarm 1 value
ON ALM1 ON
OFF PV
SP
ALM1 ON ALM1 Application example

OFF
r-g Red to Red Green To display the PV reached
Green signal
g-r Green to Green Red To display error signals
Red
230

Linked to Within Within
PV stable PV stable PV stable
band band band
Low Within High

PV
SP
Low PV stable band High Application example

r-g.r Red to Red Green Red To display stable status
Green to
Red
g-o.r Green to Green Orange Red To display stable status
Orange to
Red
o-g.r Orange to Orange Green Red To display stable status
Green to
Red
Related Parameters
See PV stable band (advanced function setting level): Page 231
pv-b PV Stable Band
This parameter sets the PV stable band width within which the PV display
color is changed.
When the mode to link to the PV stable band is selected with the PV
Function
Change Color parameter, the PV display color will change according to
whether the present value (PV) is lower than, within, or higher than the PV
stable band, as shown in the following figure.
There is a hysteresis of 0.2 (C or F).
PV stable PV stable
band band
Low Within High

PV
0.2 (C or F) SP 0.2 (C or F)
When analog inputs are used: 0.02 (%FS)

Setting tance Thermometer Universal Inputs (See note.)
Related Parameters
See PV change color (advanced function setting level): Page 230
231

a1on Alarm 1 ON Delay alarm 1 type must not be 0, 12, or
13.
13.
13.
Alarm 1, 2, or 3 outputs are prevented from turning ON until after the delay
times set in these parameters have elapsed.
Set the time for which the ON delay is to be enabled.
Function
To disable the ON delay, set 0.

Setting
0 to 999 Second 0
Related Parameters
See Alarm 1 to 3 type (initial setting level): Pages 207 to 210

a1of Alarm 1 OFF Delay alarm 1 type must not be 0, 12, or
13.
13.
13.
Alarm 1, 2, or 3 outputs are prevented from turning OFF until after the delay
times set in these parameters have elapsed.
Set the time for which the OFF delay is to be enabled.
To disable the OFF delay, set 0.
Function

0 to 999 Second 0
Setting
Related Parameters
See Alarm 1 to 3 type (initial setting level): Pages 207 to 210
232
The input type must be thermocou-

istp Input Shift Type ple or resistance thermometer.
This parameter sets the shift method for thermocouple or resistance ther-
mometer inputs.
When the input type is thermocouple or resistance thermometer, set
either a 1-point shift or a 2-point shift.
Function

ins1: 1-point shift, ins2: 2-point shift ins1
Setting
Related Parameters
See Temperature input shift, Upper-limit temperature input shift value, Lower-limit
temperature input shift value (adjustment level): Page 186
Input type (initial setting level): Page 200

mvse MV at Stop and Error Addition control.
This parameter sets whether or not the MV at Stop and MV at PV Error

parameters are to be displayed.
Set whether or not the MV at Stop and MV at PV Error parameters are to
be displayed.
Function

Setting
Related Parameters
See MV at stop, MV at PV error (adjustment level): Page 192
233

amad Auto/Manual Select Addition control.
This parameter sets whether the Auto/Manual Switch parameter is to be dis-

played.
Set whether the Auto/Manual Switch parameter is to be displayed.
Function
Setting
Related Parameters
See Auto/manual switch (operation level): Page 166

control.
rt RT The input type must be set to tem-
perature input.
This parameter executes robust tuning (RT).

When AT or ST is executed with RT selected, PID constants are automat-
ically set which make it hard for control performance to degenerate even
when control object characteristics are changed.
Function
Even when hunting occurs for PID constants when AT or ST is executed
in normal mode, it is less likely to occur when AT or ST is executed in RT
mode.
on: RT function OFF, off: RT function ON off
Setting
Related Parameters
See AT execute/cancel: Page 179, Proportional band, Integral time, Derivative
time: Page 188 (adjustment level)
PID ON/OFF: Page 204, ST: Page 205 (initial setting level)
234

hsu HS Alarm Use supported.
Set this parameter to use HS alarms.
Function
Setting

supported.
hsl HS Alarm Latch Alarm 1 must be assigned.
set to ON.
When this parameter is set to ON, the HS alarm is held until any of the fol-
lowing conditions is satisfied.
a The HS alarm current is set to 50.0 A.
Function
Setting
Related Parameters
See HS alarm use (advanced function setting level): Page 235
level)
235
Heater burnout and HS alarms must

be supported.
hsh HS Alarm Hysteresis The HS Alarm parameter must be
set to ON.
The HS Alarm Latch parameter must
be set to OFF.
This parameter sets the hysteresis for HS alarms.
Function

0.1 to 50.0 A 0.1
Setting
Related Parameters
See HS alarm use (advanced function setting level): Page 235

lba LBA Detection Time The alarm type must be set to 12
(LBA).
This parameter enables or disables the LBA function and sets the detection
time interval.
Set the time interval for detecting loop burnouts.
To disable the LBA function, set 0.
Function

0 to 9999 Second 0
Setting
Related Parameters
See Alarm 1 type (initial setting level): Page 207
LBA level: Page 237, LBA band: Page 237 (advanced function setting level)
236

lbal LBA Level The alarm type must be set to 12 (LBA).
The LBA detection time must not be 0.
This parameter sets the LBA level.

If the deviation between the SP and PV exceeds the LBA level, a loop
burnout is detected.
Function

Setting Controllers with Analog Inputs 0.01 to 99.99 %FS 10.00
Related Parameters
LBA detection time: Page 236, LBA band: Page 237 (advanced function set-
ting level)

The alarm type must be set to 12
lbab LBA Band (LBA).
The LBA detection time must not be
0.
This parameter sets the LBA band.

If a control deviation greater than the LBA band is not reduced when the
LBA level is exceeded, an loop burnout is detected.
Function

Setting
Related Parameters
LBA detection time, LBA level (advanced function setting level): Page 236
237
The transfer output type must be set

out1 Control Output 1 Assignment to OFF when the control output is a
current output.
This parameter sets the function to be assigned to control output 1.
Function
None: No function is assigned to control output 1. o
o: Heating control output is output.
Setting
c-o: Cooling control output is output. (See note 1.)
alm1: Alarm 1 is output. (See note 2.)
p.end: Program end is output. (See notes 2 and 3.)
ralm: Control output ON/OFF count alarm (See note 2.)
wr1: Work bit 1 (See notes 2 and 4.)
Note (1) If c-o is assigned for standard control, a value equivalent to 0% is output.
(2) Can be selected for relay and voltage outputs (for driving SSR) only.
(3) Can be selected when the Program Pattern parameter is set to OFF, but
the function will be disabled.
(4) WR1 to WR8 are not displayed when the logic operation function is not
used.
Related Parameters
See Standard or heating/cooling: Page 204, Program pattern: Page 205, Transfer
output type: Page 210 (initial setting level)
238
out2 Control Output 2 Assignment Control output 2 must be assigned.
This parameter sets the function to be assigned to control output 2.
Function
none: No function is assigned to control output 2. none
o: Heating control output is output. (See note
Setting 3.)
alm1: Alarm 1 is output.
p.end: Program end is output. (See note 2.)
ralm: Control output ON/OFF count alarm
wr1: Work bit 1 (See note 4.)
Note (1) If c-o is assigned for standard control, a value equivalent to 0% will be
output.
(3) If the Standard or Heating/Cooling parameter is set to heating/cooling
control, control automatically switches to c-o.
used.
Related Parameters
See Standard or heating/cooling: Page 204, Program pattern: Page 205, (initial
setting level)
239
sub1 Auxiliary Output 1 Assignment Auxiliary output 1 must be assigned.
This parameter sets the function to be assigned to auxiliary output 1.
Function
none: No function is assigned to auxiliary output 1. alm1
Setting 3.)
c-o: Cooling control output is output. (See note 1.) (See note
alm1: Alarm 1 is output. 5.)
output.
(3) If a setting is changed when the Program Pattern parameter is not set to
OFF, control automatically switches to p.end.
used.
control, this parameter will automatically be set to c-o.
Related Parameters
See Program pattern (initial setting level): Page 205
240
sub2 Auxiliary Output 2 Assignment Auxiliary output 2 must be assigned.
This parameter sets the function to be assigned to auxiliary output 2.
Function
3.)
output.
control when there is no control output 2 (E5CN/CN-U), control automat-
ically switches to c-o.
used.
Related Parameters
setting level)
241
Auxiliary output 3 must be assigned

sub3 Auxiliary Output 3 Assignment (E5AN and E5EN only).
This parameter sets the function to be assigned to Auxiliary output 3.
Function
3.)
Setting c-o: Cooling control output is output. (See note 1.)
ralm: Control output ON/Off count alarm
output.
control when there is no control output 2 (E5AN/EN), control automatical-
ly switches to c-o.
used.
Related Parameters
setting level)
242
csel Character Select
This parameter switches the characters to be displayed.

The following two types of characters can be displayed.
11-segment display
Function 7-segment display

on: 11-segment display, off: 7-segment display on
Setting When set to on, an 11-segment display is used.

t-u Soak Time Unit must not be set to OFF.
Set the soak time unit for the simple program function.
Function
m: Minutes, h: Hours m
Setting
Related Parameters
243
Alarm 1, 2, and 3 functions must be

assigned.
The SP Ramp Set Value parameter
must not be set to OFF.
alsp Alarm SP Selection The ST parameter must be set to
OFF.
The alarm type must be set to 1, 2, 3,
4, 5, 6, or 7.
This parameter sets whether the set point that triggers a deviation alarm dur-
ing SP ramp operation is to be the ramp SP or target SP.
Set whether the set point that triggers a deviation alarm is the ramp SP or
target SP.
Function
sp-m: Ramp SP, sp: SP sp-m
Setting
Related Parameters
See SP ramp set value (adjustment level): Page 193
ST (initial setting level): Page 205

manl Manual MV Limit Enable control.
This parameter sets whether the MV Upper Limit and MV Lower Limit param-
eters are to be enabled for manual MV in manual mode.
Function

Setting
Related Parameters
See MV upper limit, MV lower limit (adjustment level): Page 193
244
Alarms 1, 2, and 3 must be assigned.

pvrp PV Rate of Change Calculation Period The alarm type must be set to 13.
The change width can be found for PV input values in any set period. Dif-
ferences with previous values in each set period are calculated, and an
alarm is output if the results exceed the alarm value.
Function
The PV rate of change calculation period can be set in units of 250 ms
(sampling period).

1 to 999 Sampling period 4 (1 s)
Setting
Related Parameters
See Present value, Process value/set point (operation level): Page 165
Alarm 1 to 3 type, (Initial setting level): Pages 207 to 210
Automatic Cooling Coefficient Adjust- The control must be set to heating/

csca cooling control and 2-PID control.
ment
By setting the Automatic Cooling Coefficient Adjustment parameter to

ON, autotuning can be executed during heating/cooling control to auto-
matically calculate the cooling coefficient at the same time as the PID
Function parameters. If there is strong non-linear gain for the cooling characteris-
tics, such as when cooling water boils for cooling control, it may not be
possible to obtain the optimum cooling coefficient at the Controller, and
control may take the form of oscillating waves. If that occurs, increase the
proportional band or the cooling coefficient to improve control.

Setting
Related Parameters
See Cooling coefficient (adjustment level): Page 189
245

ocu Heater Overcurrent Use supported.
Set this parameter to use the heater overcurrent alarm.
Function

on: Enabled, off: Disabled ON
Setting

ocl Heater Overcurrent Latch supported (two CTs).
When this parameter is set to ON, the heater overcurrent alarm is held
until any of the following conditions is satisfied.
a Heater overcurrent detection is set to 50.0 A.
Function
Setting
Related Parameters
See Heater overcurrent detection 1, Heater overcurrent detection 2 (adjustment
Heater overcurrent hysteresis (advanced function setting level): Page 247
level)
246

supported, and alarm 1 must be
och Heater Overcurrent Hysteresis assigned. The Heater Overcurrent
Use parameter must be set to ON,
and the Heater Overcurrent Latch
parameter must be set to OFF.
This parameter sets the hysteresis for heater overcurrent detection.
Function

0.1 to 50.0 A 0.1
Setting
Related Parameters
See Heater overcurrent use (advanced function setting level): Page 246
The PF Key must be supported

pf PF Setting (E5AN/EN).
This parameter sets the function of the PF Key.
Function
The default is A-M.
Set value Setting Function
OFF: off Disabled Does not operate as a function key.
RUN: run RUN Specifies RUN status.
Setting
STOP: stop STOP Specifies STOP status.
R-S: r-s Reversing RUN/STOP Specifies reversing RUN/STOP opera-
operation tion status.
AT-2: at-2 100%AT Specifies reversing 100% AT Execute/
Execute/Cancel Cancel status. (See note 1.)
AT-1: at-1 40%AT Specifies reversing 40% AT Execute/
Execute/Cancel Cancel status. (See note 1.)
LAT: lat Alarm Latch Cancel Specifies canceling alarm latches. (See
note 2.)
A-M: a-m Auto/Manual Specifies reversing Auto/Manual status
(See note 3.)
PFDP: pfdp Monitor/Setting Item Specifies the monitor/setting item dis-
play. Select the monitor/setting item
using the Monitor/Setting Item 1 to 5
parameters (advanced function setting
level).
Note (1) When AT cancel is specified, it means that AT is cancelled regardless of

whether the AT currently being executed is 100% AT or 40% AT.
247
(2) Alarms 1 to 3, heater burnout, HS alarms, and heater overcurrent latches

are cancelled.
(3) For details on auto/manual operations using the PF Key, refer to 4-13 Per-
forming Manual Control.
Related Parameters
See Monitor/setting item 1 to 5 (advanced function setting level): Page 248
The PF Setting parameter must be

pfd* Monitor/Setting Item * (*: 1 to 5) set to PFDP.
Set the PF Key parameter to Monitor/Setting Item to enable using the

function key to display monitor/setting items. The items that will be dis-
played are set using the Monitor/Setting Item 1 to 5 parameters. The set-
Function tings are listed in the following table.
Set value Setting Remarks
Monitor/Setting Symbol
0 Disabled ---
Setting 1 PV/SP/Multi-SP Can be set. (SP) ---
2 PV/SP/MV (See note.) Can be set. (SP) ---
3 PV/SP/Soak time remain Can be set. (SP) ---
Note The MV for heating and cooling control is set in the MV Display Selection
parameter.
Related Parameters
See PF setting: Page 247, MV display selection: Page 249 (advanced function set-
ting level)
248
The No. 3 display must be supported

spdp PV/SP Display Screen Selection (E5AN/EN).
This parameter sets the PV/SP Screen No. 3 display and order of display.
The default is 4.*
Function * A 2-level display is set at the time of shipping from the factory. (set val-
ue: 0)
A 3-level display is activated if parameters are initialized. (set value: 4)

0 Only PV/SP is displayed (with no No. 3 display).
Setting 1 PV/SP/Multi-SP and PV/SP/MV are displayed in order. (See
note.)
2 PV/SP/MV and PV/SP/Multi-SP are displayed in order. (See
note.)
3 Only PV/SP/Multi-SP is displayed.
4 PV/SP/MV is displayed (See note.)
5 PV/SP/Multi-SP and PV/SP/Soak time remain are displayed
in order. (See note.)
6 PV/SP/MV and PV/SP/Soak time remain are displayed in
order. (See note.)
7 Only PV/SP/Soak time remain is displayed.
Note The MV for heating and cooling control is set in the MV Display Selection
parameter.
Related Parameters
MV display selection (advanced function setting level): Page 249
The No. 3 display must be supported

(E5AN/EN).
Heating and cooling control must be
used.
odsl MV Display Selection
The PV/SP Display Screen Selection
parameter must be set to 1, 2, 4, or
6, or the Monitor/Setting Item 1 to 5
parameter must be set to 2.
This parameter selects the MV display for PV/SP/MV during heating and
cooling control. Either heating MV or cooling MV can be selected.
Function

o: MV (heating) o
c-o: MV (cooling)
Setting
249
The input type must be set to tem-

pvdp PV Decimal Point Display perature input.
The display below the decimal point in the PV can be hidden for temperature
inputs.
The PV decimals below the decimal point can be hidden by setting the PV
Function Decimal Point Display parameter to OFF. When this parameter is set to
ON, the display below the decimal point will appear according to the input
type setting.

on: ON, off: OFF ON
Setting
Related Parameters
pvst PV Status Display Function
The PV in the No. 1 display for the PV/SP, PV, or PV/Manual MV Screen is
alternately displayed in 0.5-s cycles with the control and alarm status
specified for the PV status display function.
Function
Monitor range Default
off: No PV status display off
manu: MANU is alternately displayed during manual control.
Monitor
stop: STOP is alternately displayed while operation is stopped.
alm1: ALM1 is alternately displayed during Alarm 1 status.
alm: ALM is alternately displayed when Alarm 1, 2, or 3 is set to ON.
ha: HA is alternately displayed when a heater burnout alarm, HS alarm,
or heater overcurrent alarm is ON.
Related Parameters
See Process value/set point, PV (operation level): Page 165
PV/MV (manual MV) (manual control level): Page 197
250
svst SV Status Display Function
The SP, Blank, or Manual MV in the No. 2 display for the PV/SP, PV, or
PV/Manual MV Screen is alternately displayed in 0.5-s cycles with the
control and alarm status specified for the SV status display function.
Function
Monitor range Default
off: No SV status display off
manu: MANU is alternately displayed during manual control.
Monitor
stop: STOP is alternately displayed while operation is stopped.
alm: ALM is alternately displayed when Alarm 1, 2, or 3 is set to ON.
ha: HA is alternately displayed when a heater burnout alarm, HS
alarm, or heater overcurrent alarm is ON.
Related Parameters
See Process value/set point, PV (operation level): Page 165
PV/MV (manual MV) (manual control level): Page 197
d.ref Display Refresh Period
This parameter delays the display refresh period for monitor values. Only
display refreshing is delayed, and the refresh period for process values
used in control is not changed.
Function This function is disabled by setting the parameter to OFF.

OFF, 0.25, 0.5, 1.0 Second 0.25
Monitor
251
Control output 1 must be supported.

Relay or voltage outputs (for driving
SSR) must be used.
ra1m Control Output 1 ON/OFF Count Monitor
The Control Output 1 ON/OFF Count
Alarm Set Value parameter must not
be set to 0.
This parameter monitors the number of times that control output 1 is

turned ON and OFF.
This function is not displayed when the set value is 0, or when the control
Function output is a linear output.
Monitor range Unit

0 to 9999 100 times
Monitor

Relay or voltage outputs (for driving
SSR) must be used.
ra2m Control Output 2 ON/OFF Count Monitor
The Control Output 2 ON/OFF Count
Alarm Set Value parameter must not
be set to 0.
This parameter monitors the number of times that control output 2 is

turned ON and OFF.
This function is not displayed when the set value is 0, or when the control
Function output is a linear output.
Monitor range Unit

0 to 9999 100 times
Monitor
252

Control Output 1 ON/OFF Count Alarm
ra1 Relay or voltage outputs (for driving
Set Value SSR) must be used.
An ON/OFF count alarm occurs when the ON/OFF counter exceeds the
It is possible to assign ON/OFF count alarms to auxiliary outputs and to
Function have them displayed on the screen.
This function is disabled when the set value is 0.

0 to 9999 100 times 0
Monitor
Related Parameters
See Control output 1 ON/OFF count monitor (advanced function setting level):
Page 252

Control Output 2 ON/OFF Count Alarm
ra2 Relay or voltage outputs (for driving
Set Value SSR) must be used.
An ON/OFF count alarm occurs when the ON/OFF counter exceeds the
It is possible to assign ON/OFF count alarms to auxiliary outputs and to
Function have them displayed on the screen.
This function is disabled when the set value is 0.

0 to 9999 100 times 0
Monitor
Related Parameters
See Control output 2 ON/OFF count monitor (advanced function setting level):
Page 252
253
Control outputs 1 and 2 must be sup-

ported.
rac ON/OFF Counter Reset Relay or voltage outputs (for driving
SSR) must be used.
This parameter resets the ON/OFF counter for specified control outputs.
Function

0: Disable the counter reset function. 0
1: Reset the control output 1 ON/OFF counter.
Setting 2: Reset the control output 2 ON/OFF counter.
Note After the counter has been reset, the set value will be automatically returned
to 0.
Related Parameters
See Control output 1 ON/OFF count monitor, Control output 2 ON/OFF count mon-
itor (advanced function setting level): Page 252
Initial setting/communications protect

cmov Move to Calibration Level must be 0.
This parameter sets the password to move to the calibration level.

Set the password to move to the calibration level. The password is 1201.
Move to the calibration level either by pressing the M Key or O Key or by
waiting for two seconds to elapse.
Function
Related Parameter
See Initial setting/communications protect (protect level): Page 160
254
Communications Setting Level Section 5-9
5-9 Communications Setting Level
psel Protocol Setting Communications must be supported.

bps Communications Baud Rate
len Communications Data Length CompoWay/F must be selected as the protocol.
sbit Communications Stop Bits CompoWay/F must be selected as the protocol.
prty Communications Parity

sdwt Send Data Wait Time
Each parameter is enabled when the power is reset.

Match the communications specifications of the E5@N and the host com-
puter. If multiple devices are connected, ensure that the communications
specifications for all devices in the system (except the Communications
unit number) are the same.
Item Symbol Set values Settings Default
Protocol setting psel cwf, mod CompoWay/F cwf
(SYSWAY), Modbus
Communications u-no 0 to 99 0 to 99 1
Unit No.
Communications bps 1.2, 2.4, 4.8, 9.6, 1.2, 2.4, 4.8, 9.6, 9.6
baud rate 19.2, 38.4, or 57.6 19.2, 38.4, or 57.6
(kbps) (kbps)
Communications len 7 or 8 bits 7 or 8 bits 7
data length
Stop bits sbit 1 or 2 bits 1 or 2 bits 2
Communications prty none, even, odd None, Even, Odd even
parity
Send data wait time sdwt 0 to 99 0 to 99 (ms) 20
Related Parameter
See Communications writing (adjustment level): Page 180
255
Communications Setting Level Section 5-9
256
SECTION 6
CALIBRATION
This section describes how the user can calibrate the E5CN and E5CN-U Digital Temperature Controllers.
6-1 Parameter Structure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 258

6-2 User Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260
6-2-1 Calibrating Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260
6-2-2 Registering Calibration Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260
6-3 Thermocouple Calibration (Thermocouple/Resistance Thermometer Input) . 260
6-3-1 Preparations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 261
(Thermocouple/Resistance Thermometer Input) . . . . . . . . . . . . . . . . . . . . . . 264
6-5 Analog Input Calibration (Thermocouple/Resistance Thermometer Input) . . 265
6-6 Calibrating Analog Input (Analog Input) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 267
6-6-1 Calibrating a Current Input. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 267
6-6-2 Calibrating a Voltage Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 268
6-7 Checking Indication Accuracy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 270
6-7-1 Thermocouple or Infrared Temperature Sensor . . . . . . . . . . . . . . . . 270
6-7-2 Platinum Resistance Thermometer . . . . . . . . . . . . . . . . . . . . . . . . . . 271
6-7-3 Analog Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 272
257
Parameter Structure Section 6-1
6-1 Parameter Structure

To execute user calibration, enter the password 1201 at the Move to Cal-
ibration Level parameter in the advanced function setting level. The mode
will be changed to the calibration mode, and adj will be displayed.
The Move to Calibration Level parameter may not be displayed when the
user is doing the calibration for the first time. If this happens, set the Initial
Setting/Communications Protect parameter in the protect level to 0 before
moving to the advanced function setting level.
The calibration mode is ended by turning the power OFF.
The parameter calibrations in the calibration mode are structured as
shown below.
Advanced Function Setting
Level
adj Moves automatically according to input type.

30
Platinum resistance Thermocouple or infrared Analog input

thermometer temperature sensor
0: Pt100 1: Pt100 5: K 6: K 19: K140F/60C 23: 0 to 50 mV

2: Pt100 7: J 8: J 20: K240F/120C
3: JPt100 11: E 9, 10: T 21: K280F/140C
4: JPt100 12: L 13, 14: U 22: K440F/220C
15: N 16: R 24: W
17: S 25: PL II
18: B
p390 p280 t 54 t 24 c 54
e20c e26b b9a5 e220 b9as
p200 p140 t -6 t -6 t -6
9387 93d7 2988 0200 2988
p10 p10 c700 c700

4543 4543 br13 ba13
c400 c400
296e 29be
bias bias
35b8 35b8
str
no
258
Parameter Structure Section 6-1
Controllers with an Analog Input

Advanced Function
Setting Level
adj
30 Moves automatically according to input type.
Current input Voltage input
0: 4 to 20 mA 2: 1 to 5 V 4: 0 to 10 V
1: 0 to 20 mA 3: 0 to 5 V
a 20 1v 5 2v10
c8e7 c7c3 b104
a 1 1v 1 2v 1
4677 sac0 4ad9
str
no
When calibration has been performed after purchase, the user calibration
information shown in the following illustration will be displayed when moving to
the calibration level.
.adj
30
A dot is displayed.
259
User Calibration Section 6-2
6-2 User Calibration

The E5CN/CN-U/AN/EN/GN is correctly calibrated before it is shipped from
the factory, and normally need not be calibrated by the user.
If, however, it must be calibrated by the user, use the parameters for calibrat-
ing temperature input and analog input. OMRON, however, cannot ensure the
results of calibration by the user. Also, calibration data is overwritten with the
latest calibration results. The default calibration settings cannot be restored
after user calibration. Perform user calibration with care.
6-2-1 Calibrating Inputs

The input type selected in the parameter is used for calibration. The input
types are as follows:
Thermocouple: 16 types
Infrared temperature sensor: 4 types
Analog input: 1 type
Platinum resistance thermometer: 5 types
Controllers with Analog Inputs
Current input: 2 types
Voltage input: 3 types
6-2-2 Registering Calibration Data

The new calibration data for each item is temporarily registered. It can be offi-
cially registered as calibration data only when all items have been calibrated
to new values. Therefore, be sure to temporarily register all items when you
perform the calibration. When the data is registered, it is also recorded that
user calibration has been performed.
Prepare separate measuring devices and equipment for calibration. For
details on how to handle measuring devices and equipment, refer to the
respective instruction manuals.
6-3 Thermocouple Calibration (Thermocouple/Resistance

Thermometer Input)
Calibrate according to the type of thermocouple: thermocouple 1 group
(input types 5, 7, 11, 12, 15) and thermocouple 2 group (input types 6, 8,
9, 10, 13, 14, 16, 17, 18, 19, 20, 21, 22, 24, 25).
When calibrating, do not cover the bottom of the Controller. Also, do not
touch input terminals/pins (terminals 4 and 5 on the E5CN, pins 1 and 2
on the E5CN-U, pins 19 and 20 on the E5AN/E5EN, or pins 11 and 12 on
the E5GN) or compensating conductors.
260
Thermocouple Calibration (Thermocouple/Resistance Thermometer Input) Section 6-3
6-3-1 Preparations
E5CN STV E5CN-U STV

Input power supply Input power supply
Cold junction Cold junction

compensator compensator
+ 0C/32F + 0C/32F
Compensating conductor Compensating conductor
STV E5GN STV
E5AN/EN
Cold junction Cold junction

compensator compensator
+ 0C/32F + 0C/32F
Compensating conductor Compensating conductor
Set the cold junction compensator designed for compensation of internal
thermocouples to 0C. Make sure that internal thermocouples are dis-
abled (i.e., that tips are open).
In the above figure, STV indicates a standard DC current/voltage source.
Use the compensating conductor designed for the selected thermocou-
ple. When thermocouples R, S, E, B, W, or PLII or an infrared temperature
sensor is used, the cold junction compensator and the compensating con-
ductor can be substituted with the cold junction compensator and the
compensating conductor for thermocouple K.
Connecting the Cold Junction Compensator

Correct process values cannot be obtained if you touch the contact ends of
the compensating conductor during calibration of a thermocouple. Accord-
ingly, short-circuit (enable) or open (disable) the tip of the thermocouple inside
the cold junction compensator as shown in the figure below to create a con-
tact or non-contact state for the cold junction compensator.
Cold junction compensator Cold junction compensator
Short-circuit
E5CN 0C/32F
E5CN 0C/32F Open
E5CN-U E5CN-U
E5AN E5AN
E5EN E5EN
Compensating conductor E5GN Compensating conductor
E5GN
261
In this example, calibration is shown for a Controller with a Thermocouple/

Resistance Thermometer Universal Input, with thermocouple/infrared temper-
ature sensor set as the input type.
1,2,3... 1. Connect the power supply.
2. Connect a standard DC current/voltage source (STV), precision digital
multimeter (DMM), and contact junction compensator (e.g., a zero con-
troller as in the figure) to the thermocouple input terminals, as shown in
the figure below.
STV

DMM
+
Leave open.
Zero
controller
OUTPUT INPUT
Compensating conductor of currently selected
thermocouple.
Use K thermocouple compensating conductor
for E, R, S, B, W, and PLII thermocouples and
for an infrared temperature sensor.
3. Turn the power ON.

4. Move to the calibration level.
adj This starts the 30-minute aging timer. This timer provides an approximate
timer for aging. After 30 minutes have elapsed, the No. 2 display changes
30
to 0. You can advance to the next step in this procedure even if 0 is not
displayed.
Input types 5, 7, 11, 12, 15: 5. When the M Key is pressed, the status changes as shown to the left.
The No. 2 display at this time shows the currently entered count value in
t-54 hexadecimal. Set the STV as follows:
b9a5 Input types 5, 7, 11, 12, 15: Set to 54 mV.
Input types 6, 8, 9, 10, 13, 14, 16, 17, 18, 19, 20, 21, 22, 24, 25:
Input types 6, 8, 9, 10, 13, 14, 16,
Set to 24 mV.
17, 18, 19, 20, 21, 22, 24, 25:
Allow the count value on the No. 2 display to fully stabilize, then press the
t-24 D Key to temporarily register the calibration settings.
If this count value is outside of the specified range, the No. 2 display will
e220 flash and the count value will not be temporarily registered.
6. When the M Key is pressed, the status changes as shown to the left.
t--6 Set the STV to 6 mV.
2988
D Key to temporarily register the calibration settings.
flash and the count value will not be temporarily registered.
7. Press the M Key. The display changes as shown on the left. Set the STV
c700
- to 700 mV.
ba13
262
8. Press the M Key. The display changes as shown on the left.

c400
4 Set the STV to 400 mV.
29be
bias
35b8
10. Change the wiring as follows:
Open in non-connected state
STV

DMM
+
Short-circuit
Zero
controller
OUTPUT INPUT
Compensating conductor of currently selected
thermocouple.
Use K thermocouple compensating conductor
for E, R, S, B, W, and PLII thermocouples and
for an infrared temperature sensor.
Disconnect the STV to enable the thermocouple of the cold junction com-
pensator. When doing this, be sure to disconnect the wiring on the STV
side.
11. Allow the count value on the No. 2 display to fully stabilize, then press the
str The data to be temporarily registered is not displayed if it is not complete.
Press the U Key. The No. 2 display changes to yes. Release the key and
no
wait two seconds or press the M Key. This stores the temporarily regis-
tered calibration data to EEPROM. To cancel the saving of temporarily
registered calibration data to EEPROM, press the M Key (while no is dis-
played in the No. 2 display) without pressing the U Key.
13. The calibration mode is ended by turning the power OFF.
263
Platinum Resistance Thermometer Calibration (Thermocouple/Resistance Thermometer Input) Section 6-4

(Thermocouple/Resistance Thermometer Input)
In this example, calibration is shown for Controller with a Thermocouple/
Resistance Thermometer Universal Input, with a resistance thermometer set
as the input type.
Use connecting wires of the same thickness.
2. Connect a precision resistance box (called a 6-dial in this manual) to the
platinum resistance thermometer input terminals, as shown in the follow-
ing diagram.
9
E5CN
Input power supply
10 A 3
B' 4 6-dial
B 5
10
E5CN-U
Input power supply
11 A 3
B' 2 6-dial
B 1
1
E5AN/EN
Input power supply
2 A 18
B' 19 6-dial
B 20
1
E5GN
Input power supply
2 A 10
B' 11 6-dial
B 12

30
displayed.
Input type 0: 5. Execute calibration for the main input.
Press the M Key to display the count value for each input type.
p390 The No. 2 display at this time shows the currently entered count value in
hexadecimal. Set the 6-dial as follows:
e20c
Input type 0: 390
Input types 1, 2, 3, 4:
Input type 1, 2, 3 or 4: 280
p280 D Key to temporarily register the calibration settings.
e26b If this count value is outside of the specified range, the No. 2 display will
264
Analog Input Calibration (Thermocouple/Resistance Thermometer Input) Section 6-5
Input type 0: Press the M Key to display the count value for each input type.
The No. 2 display at this time shows the currently entered count value in hexa-
p200 decimal. Set the 6-dial as follows:
Input type 0: 200
93a7
Input type 1, 2, 3 or 4: 140
Input types 1, 2, 3, 4: Allow the count value on the No. 2 display to fully stabilize, then press the D Key
to temporarily register the calibration settings.
p140 If this count value is outside of the specified range, the No. 2 display will flash
and the count value will not be temporarily registered.
e26b
p-10 Set the 6-dial to 10 .
4543 Allow the count value on the No. 2 display to fully stabilize, then press the
no
tered calibration data to EEPROM.
To cancel the saving of temporarily registered calibration data to EE-
PROM, press the M Key (while no is displayed in the No. 2 display) with-
out pressing the U Key.
8. The calibration mode is quit by turning the power OFF.
6-5 Analog Input Calibration (Thermocouple/Resistance

Thermometer Input)
In this example, calibration is shown for a Controller with a Thermocouple/
Resistance Thermometer Universal Input, with an analog input (0 to 50 mV)
set as the input type.
E5CN E5CN-U
9 10
10 11
STV 4 STV 2
DMM 5 + DMM 1 +
E5AN/EN E5GN
1 1
2 2
STV 19 STV 11
DMM 20 + DMM 12 +
265
Analog Input Calibration (Thermocouple/Resistance Thermometer Input) Section 6-5

2. Connect an STV and DMM to the analog input terminals (same as ther-
mocouple inputs), as shown in the figure above.
30
displayed.
t-54 The No. 2 display at this time shows the currently entered count value in
hexadecimal. Set the STV to 54 mV.
b9a5
t--6 Set the STV to 6 mV.
no
266
Calibrating Analog Input (Analog Input) Section 6-6
6-6 Calibrating Analog Input (Analog Input)

6-6-1 Calibrating a Current Input
In this example, calibration is shown for a Controller with an Analog Input, with
a current input set as the input type.
2. Connect an STV and DMM to the current input terminals, as shown in the
following diagram.
E5CN E5AN/EN
9 1
10 2
STV 4 STV 19
DMM 3 + DMM 18 +
E5CN-U E5GN
10 1
11 2
STV 2 STV 11
DMM 3 + DMM 10 +

30
displayed.
a-20 The No. 2 display at this time shows the currently entered count value in
hexadecimal. Set the STV to 20 mA.
c8e7
a--1 Set the STV to 1 mA.
267
no
6-6-2 Calibrating a Voltage Input

In this example, calibration is shown for a Controller with an Analog Input, with
a voltage input set as the input type.
2. Connect an STV and DMM to the voltage input terminals, as shown in the
following diagram.
E5CN E5AN/EN
9 1
10 2
STV 4 STV 19
DMM 5 + DMM 20 +
E5CN-U E5GN
10 1
11 2
STV 2 STV 11
DMM 1 + DMM 12 +

30
displayed.
Input type 2 or 3: 5. When the M Key is pressed, the status changes as shown to the left.
The No. 2 display at this time shows the currently entered count value in
1v-5 hexadecimal. Set the STV as follows:
c7c3 Input type 2 or 3: 5 V
Input type 4: 10 V
Input type 4:
2v10 If this count value is outside of the specified range, the No. 2 display will
b104 flash and the count value will not be temporarily registered.
268
Input type 2 or 3: 6. When the M Key is pressed, the status changes as shown to the left.
Set the STV to 1 V.
1v-1 Allow the count value on the No. 2 display to fully stabilize, then press the
5ac0 D Key to temporarily register the calibration settings.
Input type 4: flash and the count value will not be temporarily registered.
2v-1
4ad9
no
269
Checking Indication Accuracy Section 6-7
6-7 Checking Indication Accuracy

After calibrating the input, be sure to check the indication accuracy to
make sure that the calibration has been executed correctly.
Operate the E5CN/CN-U/AN/EN in the process value/set point monitor
mode.
Check the indication accuracy at the following three values: upper limit,
lower limit, and mid-point.
6-7-1 Thermocouple or Infrared Temperature Sensor

Preparations
The diagram below shows the required device connections. Make sure
that the E5CN/CN-U/AN/EN/GN and cold junction compensator are con-
nected by a compensating conductor for the thermocouple that is to be
used during actual operation.
9 E5CN
Input power supply
10 Cold junction compensator
4
STV
+ 5
Compensating conductor
10 E5CN-U
Input power supply
2
STV
+ 1
1 E5AN/EN
Input power supply
19
STV
+ 20
1 E5GN
Input power supply
11
STV
+ 12
Operation
Make sure that the cold junction compensator is at 0C, and set the STV
output to the voltage equivalent of the starting power of the check value.
The cold junction compensator and compensation conductor are not
required when an external cold junction compensation method is used.
270
6-7-2 Platinum Resistance Thermometer

Preparations
The diagram below shows the required device connections.
9
E5CN
Input power supply
10 A 3
B' 4 6-dial
B 5
10
E5CN-U
Input power supply
11 A 3
B' 2 6-dial
B 1
1
E5AN/EN
Input power supply
2 A 18
B' 19 6-dial
B 20
1
E5GN
Input power supply
2 A 10
B' 11 6-dial
B 22
Operation
Set the 6-dial to the resistance equivalent to the check value.
271
6-7-3 Analog Input

Preparations
The diagram below shows the required device connections.
(The connection terminals depend on the model and input type.)
Controller with a Thermocouple/Resistance Thermometer Universal
Input (Analog Input)
9
E5CN
Input power supply
10
4
STV
+ 5
10
E5CN-U
Input power supply
11
2
STV
+ 1
1
E5AN/EN
Input power supply
2
19
STV
+ 20
1
E5GN
Input power supply
2
11
STV
+ 12
272
Current Input for a Controller with an Analog Input

9
E5CN
Input power supply
10
+ 3
STV
4
10
E5CN-U
Input power supply
11
+ 3
STV
2
1
E5AN/EN
Input power supply
2
+ 18
STV
19
1
E5GN
Input power supply
2
+ 10
STV
11
Voltage Input for a Controller with an Analog Input
9
E5CN
Input power supply
10
4
STV
+ 5
10
E5CN-U
Input power supply
11
2
STV
+ 1
1
E5AN/EN
Input power supply
2
19
STV
+ 20
1
E5GN
Input power supply
2
11
STV
+ 12
Operation
Set the STV output to the voltage or current equivalent to the check value.
273
274
Appendix
Specifications
Ratings
Supply voltage 100 to 240 VAC, 50/60 Hz 24 VAC, 50/60 Hz/24 VDC
Operating voltage range 85% to 110% of rated supply voltage
Power consump- E5CN 7.5 VA 5 VA/3 W
tion E5CN-U 6 VA 3 VA/2 W (4 VA/2 W for current output)
E5AN 10 VA 5.5 VA/4 W
E5EN 10 VA 5.5 VA/4 W
E5GN 5.5 VA 3 VA/2 W
Sensor input (See note 1.) Temperature input type
Thermocouple: K, J, T, E, L, U, N, R, S, B, W, PLII
Platinum resistance thermometer: Pt100, JPt100
Infrared temperature sensor: 10 to 70C, 60 to 120C, 115 to 165C, 140 to 260C
Voltage input: 0 to 50 mV
Controllers with Analog Inputs (See note 2.)
Current input: 4 to 20 mA, 0 to 20 mA (Input impedance: 150 max.)
Voltage input: 1 to 5 V, 0 to 5 V, 0 to 10 V (Input impedance: 1 M max.)
Control output Relay output E5CN Relay output:
SPST-NO, 250 VAC, 3 A (resistive load), electrical dura-
bility: 100,000 operations
Min. applicable load: 5 V, 10 mA
Long-life relay output (using a triac):
bility: 1,000,000 operations
Load power supply voltage: 75 to 250 VAC (See note 3.)
Leakage current: 5 mA max. (250 VAC, 60 Hz)
E5CN-U SPDT, 250 VAC, 3A (resistive load), electrical durability:
100,000 operations
Min. applicable load 5 V 10 mA
E5AN Relay output:
E5EN SPST-NO, 250 VAC, 5 A (resistive load), electrical dura-
bility: 100,000 operations
Long-life relay output (using a triac):
bility: 1,000,000 operations
Load power supply voltage: 75 to 250 VAC (See note 3.)
Leakage current: 5 mA max. (250 VAC, 60 Hz)
E5GN SPST-NO, 250 VAC, 2 A (resistive load), electrical durability:
100,000 operations,
Voltage output E5CN Output voltage 12 VDC 15% (PNP), max. load current
E5CN-U 21 mA, with short-circuit protection circuit
E5AN Output voltage 12 VDC 15% (PNP), max. load current
E5EN 40 mA, with short-circuit protection circuit
Note Control output 2: 12 VDC 15% (PNP), max. load cur-
rent 21 mA, with short-circuit protection circuit
E5GN Output voltage 12 VDC 15% (PNP), max. load current
21 mA, with short-circuit protection circuit
Current output 4 to 20 mA DC, 0 to 20 mA DC, Load: 500 max. for E5GN and 600
max. for other models, Resolution: Approx. 10,000
275
Appendix
Auxiliary output E5CN SPST-NO, 250 VAC, 3 A (resistive load), electrical durability: 100,000
E5CN-U operations
E5AN SPST-NO, 250 VAC, 3 A (resistive load), electrical durability: 100,000
E5EN operations
E5GN SPST-NO, 250 VAC, 2 A (resistive load), electrical durability: 100,000
operations,
Control method 2-PID or ON/OFF control
Setting method Digital setting using front panel keys
Indication method 11-segment/7-segment digital display and single-lighting indicator
Other functions Depend on the model
Ambient temperature 10 to 55C (with no condensation or icing); with 3-year guarantee: 10 to 50C
Ambient humidity 25% to 85%
Storage temperature 25 to 65C (with no condensation or icing)
Altitude 2,000 m or less
Recommended fuse T2A, 250 VAC, time lag, low shut-off capacity
Installation environment Installation Category II, Pollution Class 2 (IEC 61010-1 compliant)
Note (1) For the setting ranges for each sensor input, see page 303.
(2) When connecting the ES2-THB, connect it 1:1.
(3) Always connect an AC load to a long-life relay output. The output will not turn OFF if a DC load is
connected, because a triac is used for switching when closing and opening the circuit.
HB, HS, and Heater Overcurrent Alarms (for E5CN/AN/EN/GN Controllers with Heater
Burnout, HS, and Heater Overcurrent Alarms)
Max. heater current 50 A AC
Input current readout accuracy 5% FS 1 digit max.
Heater burnout alarm setting 0.1 to 49.9 A (0.1 A units)
range 0.0 A: Heater burnout alarm output turns OFF.
50.0 A: Heater burnout alarm output turns ON.
Min. detection ON time: 100 ms (See note 1.)
HS alarm setting range 0.1 to 49.9 A (0.1 A units)
0.0 A: HS alarm output turns ON.
50.0 A: HS alarm output turns OFF.
Min. detection OFF time: 100 ms (See note 2.)
Heater overcurrent alarm setting 0.1 to 49.9 A (0.1 A units)
range 0.0 A: Heater overcurrent alarm output turns ON.
50.0 A: Heater overcurrent alarm output turns OFF.
Min. detection OFF time: 100 ms
Note (1) When the control output 1 ON time is less than 100 ms, heater burnout detection, heater overcurrent
detection, and heater current measurement are not performed.
(2) When the control output 1 OFF time is less than 100 ms, HS alarm, and leakage current measure-
ment are not performed.
External Power Supply for ES1B
Output voltage 12 VDC 10%
Output current 20 mA max.
Note Contact your OMRON representative for information on using the external power supply for ES1B for
other applications.
276
Appendix
Characteristics
Indication accuracy Thermocouple (See note 1.):
(ambient temperature E5CN/AN/EN/GN: (0.3% of PV or 1C, whichever is greater) 1 digit max.
of 23C) E5CN-U: (1% of PV or 2C, whichever is greater) 1 digit max.
Platinum resistance thermometer:
(0.2% of PV or 0.8C, whichever is greater) 1 digit max.
Analog input: 0.2% FS 1 digit max.
CT input: 5% FS 1 digit max.
Temperature variation Thermocouple (R, S, B, W, PLII)
influence (See note 2.) E5CN/AN/EN/GN: (1% of PV or 10C, whichever is greater) 1 digit max.
E5CN-U: (2% of PV or 10C, whichever is greater) 1 digit max.
Other thermocouples:
E5CN/AN/EN/GN: (1% of PV or 4C, whichever is greater) 1 digit max.
E5CN-U: (2% of PV or 4C, whichever is greater) 1 digit max.
Voltage variation influ-
ence (See note 2.) *K thermocouple at 100C max: 10C max.
Platinum resistance thermometer:
(1% of PV or 2C, whichever is greater) 1 digit max.
Analog input: 1% FS 1 digit max.
CT input: 5% FS 1 digit max.
Hysteresis Controllers with Thermocouple/ 0.1 to 999.9C or F
Resistance Thermometer Uni- (in units of 0.1C or F) (See note 3.)
versal Inputs
Controllers with Analog Inputs 0.01% to 99.99% FS (in units of 0.01% FS)
Proportional band (P) Controllers with Thermocouple/ 0.1 to 999.9C or F
Resistance Thermometer Uni- (in units of 0.1 EU) (See note 3.)
versal Inputs
Controllers with Analog Inputs 0.1% to 999.9% FS (in units of 0.1% FS)
0.01% to 99.99% FS (in units of 0.01% FS)
Integral time (I) 0 to 3,999 s (in units of 1 s)
Derivative time (D) 0 to 3,999 s (in units of 1 s)
When RT is ON: 0.0 to 999.9 (in units of 0.1 s)
Control Period 0.5, 1 to 99 s (in units of 1 s)
Manual reset value 0.0% to 100.0% (in units of 0.1%)
Alarm setting range 1,999 to 9,999 (decimal point position depends on input type)
Sampling period 250 ms
Insulation resistance 20 M min. (at 500 VDC)
Dielectric strength 2,300 VAC, 50/60 Hz for 1 min between terminals of different charge
Malfunction vibration 10 to 55 Hz, 20 m/s2 for 10 min each in X, Y and Z directions
Vibration resistance 10 to 55 Hz, 20 m/s2 for 2 hr each in X, Y, and Z directions
Malfunction shock 100 m/s2, 3 times each in X, Y, and Z directions
Shock resistance 300 m/s2, 3 times each in X, Y, and Z directions
Weight E5CN Approx. 150 g Adapter: approx. 10 g Terminal cover: approx. 10 g
E5CN-U Approx. 110 g ---
E5AN Approx. 310 g Adapter: approx. 100 g Terminal cover: approx. 1.6 g
E5EN Approx. 260 g per cover
E5GN Approx. 90 g Adapter: approx. 10 g ---
Degree of E5CN Front panel: IP66
protection E5AN Rear case: IP20
E5EN Terminals: IP00
E5GN
E5CN-U Front panel: IP50, rear case: IP20, terminals: IP00
Memory protection EEPROM (non-volatile memory) (number of writes: 1,000,000)
277
Appendix
Note (1) The indication accuracy of K thermocouples in the 200 to 1,300C range, T and N thermocouples
at a temperature of 100C or less, and U and L thermocouples at any temperature is 2C 1 digit
maximum. The indication accuracy of B thermocouples at a temperature of 400C to 8003C or
less is not specified. The indication accuracy of R and S thermocouples at a temperature of 200C
or less is 3C 1 digit maximum. The indication accuracy of W thermocouples is (the larger of
0.3% or 3C) 1 digit maximum and the indication accuracy of PLII thermocouples is (the larger
of 0.3% or 2C) 1 digit maximum.
(2) Ambient temperature: 10C to 23C to 55C
Voltage range: 15 to +10% of rated voltage
(3) Set None as the unit for Controllers with Analog Inputs.
Rating and Characteristics of Options

Event inputs Contact Input
ON: 1 k max., OFF: 100 k min.
Non-contact Input
ON: Residual voltage 1.5 V max.; OFF: Leakage current 0.1 mA max.
Communications Transmission path: RS-485/232C
Communications method: RS-485 (2-wire, half duplex) or RS-232C
Synchronization: Start-stop
Baud rate: 1.2, 2.4, 4.8, 9.6, 19.2, 38.4, or 57.6 kbps
Transfer output 4 to 20 mA DC, Load: 600 max., Resolution: 10,000, Accuracy: 0.3%
Waterproof Packing
If the Waterproof Packing is lost or damage, order one of the following models.
Y92S-29 (for DIN 48 48) Y92S-P4 (for DIN 96 96)
Y92S-32 (for DIN 48 24) Y92S-P4 (for DIN 48 96)
278
Appendix
Current Transformer (CT)

Specifications
Item Specifications
Model number E54-CT1 E54-CT3
Max. continuous current 50 A 120 A (See note.)
Dielectric strength 1,000 VAC (for 1 min)
Vibration resistance 50 Hz, 98 m/s2
Weight Approx. 11.5 g Approx. 50 g
Accessories None Armature (2), Plug (2)
Note The maximum continuous current of the E5@N is 50 A.
External Dimensions
E54-CT1
21 2.8
15
7.5
a.
di
8
5.
25
10.5
3
a.
di
40
5
3.
o,
Tw
10
30
E54-CT3
30 2.36 dia.
9
a.
di
12
40 40
:4
pth
de
s,
le
ho
3
M
wo,
T
15
30
279
Appendix
E58-CIFQ1 USB-Serial Conversion Cable

Specifications
Item Specifications
Applicable OS Windows 2000/XP/Vista
Applicable software CX-Thermo
Applicable models OMRON E5AN/EN/CN/CN-U/GN Digital Temperature Control-
lers
USB interface rating Conforms to USB Specification 1.1
DTE speed 38,400 bps
Connector specifications Computer end: USB (type A plug)
Temperature Controller end: Serial
Power supply Bus power (5 VDC supplied from USB host controller)
Current consumption 70 mA
Ambient operating temperature 0 to 55C (with no condensation or icing)
Ambient operating humidity 10% to 80%
Storage temperature 20 to 60C (with no condensation or icing)
Storage humidity 10% to 80%
Altitude 2,000 m max.
Weight Approx. 100 g
Compatible Operating Environment

A personal computer that includes the following specifications is required.
USB port
CD-ROM drive
Windows 2000/XP/Vista
Appearance and Nomenclature

Appearance
(2,100 mm)
250 mm LED (SD) 1,765 mm
USB connector (type A plug) LED (RD) Serial connector
LED Indicator Display

Indicator Color Status Meaning
SD Yellow Lit Sending data from USB-Serial Conversion Cable
Not lit Not sending data from USB-Serial Conversion Cable
RD Yellow Lit Receiving data from the USB-Serial Conversion Cable
Not lit Not receiving data from the USB-Serial Conversion Cable
280
Appendix
Error Displays
When an error occurs, the error contents are shown on the No. 1 or the No. 2 display.
This section describes how to check error codes on the display, and the actions to be taken to remedy the
problems.
s.err Input Error
Meaning
The input value has exceeded the control range. (See note.)
The input type setting is not correct.
The sensor is disconnected or shorted.
The sensor wiring is not correct.
The sensor is not wired.
Note Control Range
Resistance thermometer, thermocouple input: Temperature setting lower limit 20C to temperature
setting upper limit +20C
(Temperature setting lower limit 40F to temperature
setting upper limit +40F)
ES1B input: Same as input indication range
Analog input 5% to +105% of scaling range
Action
Check the wiring of inputs for miswiring, disconnections, and short-circuits and check the input type.
If no abnormality is found in the wiring and input type, turn the power OFF then back ON again.
If the display remains the same, the Controller must be replaced. If the display is restored, then the probable
cause is electrical noise affecting the control system. Check for electrical noise.
Note With resistance thermometer input, a break in the A, B, or B line is regarded as a disconnection.
Operation at Error
After an error occurs, the error is displayed and the alarm outputs function as if the upper limit has been
exceeded.
When the Input Error Output parameter in the advanced function setting level is set to ON, the output assigned
to the alarm 1 function turns ON whenever an input error occurs.
An error message is displayed when the PV, PV/SP, or PV/MV is displayed.
Note The control output turns OFF. When the manual MV, MV at stop, or MV at PV error is set, however the
control output corresponds to the set value.
[[[[
Display Range Exceeded
]]]]
Meaning
Though this is not an error, it is displayed if the process value exceeds the display range when the control
range is larger than the display range.
The display ranges are shown below (with decimal points omitted).
When less than 1,999 [[[[
When more than 9,999 ]]]]
281
Appendix
Action
Control continues, allowing normal operation. The message is displayed when the PV, PV/SP, or PV/MV is dis-
played.
Resistance thermometer input (Except for models with a Resistance thermometer input (Except for models with a
setting range of 199.9 to 500.0C) setting range of 1999. to 500.0C)
Thermocouple input (Except for models with a setting range of Thermocouple input (Except for models with a setting range of
199.9 to 400.0C) 199.9 to 400.0C)
ES1B Control range Control range
s.err display Numeric display s.err display s.err display [[[[ display Numeric display s.err display
Input indication range Input indication range
Analog Input Analog Input

When display range < control range When display range > control range
Control range Control range
s.err display [[[[ display Numeric display ]]]] display s.err display s.err display Numeric display s.err display
Input indication range
1999 Display range 9999 1999 Display range 9999

(See note.) (See note.)
Note: The display range is shown in numbers with decimal points omitted.
e333 AD Converter Error
Meaning
There is an error in internal circuits.
Action
First, turn the power OFF then back ON again. If the display remains the same, the Controller must be
repaired. If the display is restored, then the probable cause is electrical noise affecting the control system.
Check for electrical noise.
Operation
Control output and alarm output turn OFF.
e111 Memory Error
Meaning
Internal memory operation is in error.
Action
First, turn the power OFF then back ON again. If the display remains the same, the Controller must be
repaired. If the display is restored, then the probable cause is electrical noise affecting the control system.
Check for electrical noise.
Operation at Error
Control output and alarm output turn OFF. (Current output is approx. 0 mA).
ffff Current Value Exceeds
Meaning
This error is displayed when the heater current value exceeds 55.0 A.
282
Appendix
Action
Control continues, allowing normal operation. An error message is displayed when the following items are dis-
played.
Heater current 1 value monitor
Heater current 2 value monitor
Leakage current 1 monitor
Leakage current 2 monitor
ct1
Heater Burnout
ct2 HS Alarm
lcr1 Heater Overcurrent
lcr2
Meaning
When heater burnout, HS alarm, or heater overcurrent occurs, the No. 1 display in the applicable setting level
flashes.
Action
When a heater burnout, HS error, or heater overcurrent is detected, the HA indicator lights and the No. 1 dis-
play flashes for the applicable Heater Current 1 Value Monitor, Heater Current 2 Value Monitor, Leakage Cur-
rent 1 Monitor, or Leakage current 2 Monitor parameters in the operation level and adjustment level. Control
continues, allowing normal operation.
283
Appendix
Troubleshooting
Checking Problems
If the Temperature Controller is not operating normally, check the following points before requesting repairs. If
the problem persists, contact your OMRON representative for details on returning the product.
Timing Status Meaning Countermeasures Page
Turning ON the Temperature unit ST (self-tuning) is in This is not a product fault. The temperature 64
power for the (C/F) is flashing. progress (default unit (C/F) flashes while ST (self-tuning) is
first time setting: ON). being performed
Temperature error is Input type mismatch Check the sensor type and reset the input 52
large. type correctly.
Input error (S.Err dis- Thermometer is not Check the thermometer installation location 31
play) installed properly. and polarity and install correctly.
Communications are Non-recommended Make sure that the connected device is not Section 1 of
not possible. adapter is being faulty. Communi-
used. cations
Manual
Communications are Non-recommended Make sure that the connected device is not (See note.)
not possible. adapter is being faulty.
used.
During opera- Overshooting ON/OFF control is Select PID control and execute either ST 62
tion Undershooting enabled (default: (self-tuning) or AT (auto-tuning).
Hunting ON/OFF control When using self-tuning, turn ON the power
selected). supply to the Temperature Controller and
load (heater, etc.) at the same time, or turn
ON the load power supply first. Accurate
self-tuning and optimum control will not be
possible if the power supply to the load is
turned ON after turning ON the power sup-
ply to the Temperature Controller.
Control cycle is Shorten the control cycle. A shorter control 54
longer compared cycle improves control performance, but a
with the speed of cycle of 20 ms minimum is recommended in
rise and fall in tem- consideration of the service life of the
perature relays.
Unsuitable PID con- Set appropriate PID constants using either 62
stant of the following methods.
Execute AT (autotuning).
Set PID constants individually using man-
ual settings.
HS alarm operation Use breeder resistance if the problem is 54
fault due to leakage current. Also investigate the
errors detected by the HS alarm function.
Temperature is not Specified operation Select either forward or reverse operation 54
rising is unsuitable for depending on the required control. Reverse
required control operation is used for heating operations.
(default: Reverse
operation)
Heater is burnt out or Check whether heater burnout or deteriora- 54
deteriorated. tion have occurred. Also investigate the
errors detected by the heater burnout
alarm.
Insufficient heater Check whether the heaters heating capac- ---
capacity ity is sufficient.
Cooling system in Check whether a cooling system is operat- ---
operation. ing.
Peripheral devices Set the heating prevention temperature set- ---
have heat preventing to a value higher than the set tempera-
tion device operat- ture of the Temperature Controller.
ing.
Note Refer to the E5CN/E5AN/E5EN/E5GN Digital Temperature Controller Communications Manual (Cat. No.
H158) for details.
284
Appendix
Timing Status Meaning Countermeasures Page

During opera- Output will not turn Set to STOP Set the RUN/STOP mode to RUN. If STOP 172
tion (continued) ON (default: RUN) is lit on the display, control is stopped.
Specified operation Select either forward or reverse operation 54
is unsuitable for depending on the required control. Reverse
required control operation is used for heating operations.
(default: Reverse
operation)
A high hysteresis is Set a suitable value for the hysteresis. 60
set for ON/OFF oper-
ation (default: 1.0C)
Temperature Con- Set to STOP Set the RUN/STOP mode to RUN. If STOP 172
troller will not oper- (default: RUN) is lit on the display, control is stopped.
ate
Temperature error is Thermometer has Check whether the thermometer has burnt ---
large burnt out or short-cir- out or short-circuited
Input error (S.err dis-
cuited.
play) Thermometer lead Wire the lead wires and power lines in sep- ---
wires and power arate conduits, or wiring using a more direct
lines are in the same path.
conduit, causing
noise from the power
lines (generally, dis-
play values will be
unstable).
Connection between Connect the thermocouples lead wires ---
the Temperature directly, or connect a compensating conduc-
Controller and ther- tor suitable for the thermocouple.
mocouple is using
copper wires.
Installation location Check whether the location of the thermom- ---
of thermometer is eter is suitable.
unsuitable.
Input shift is not set Set a suitable input shift. If input shift is not 89
correctly (default: required, set the input shift value to 0.0.
0C)
Keys will not operate Setting change pro- Turn OFF setting change protect. 110
tect is ON.
Cannot shift levels Operations limited Set the operation/adjustment protect, initial 110
due to protection. setting/communications protect, and set-
ting change protect values as required.
After long ser- Control is unstable Terminal screws may Retighten terminal screws to a torque of 33
vice life be loose. 0.74 to 0.90 Nm (see note).
The internal compo- The Temperature Controllers internal elec- ---
nents have reached trolytic capacitor depends on the ambient
the end of their ser- temperature, and load rate. The structural
vice life. life depends on the ambient environment
(shock, vibration). The life expectancy of the
output relays varies greatly with the switch-
ing capacity and other switching conditions.
Always use the output relays within their
rated load and electrical life expectancy. If
an output relay is used beyond its life
expectancy, its contacts may become
welded or burned. Replace the Temperature
Controller and all other Temperature Con-
trollers purchased in the same time period.
Note The tightening torque is 0.5 Nm for the E5CN-U and 0.43 to 0.58 Nm for the E5GN. The terminal torque
is 0.5 to 0.6 Nm for auxiliary output 2 on the E5GN.
285
Appendix
Symptom: Cannot Communicate or a Communications Error

Occurs
Meaning Countermeasures
The communications wiring is not correct. Correct the wiring.
The communications line has become dis- Connect the communications line securely and tighten the screws.
connected.
The communications cable is broken. Replace the cable.
The communications cable is too long. The total cable length is 500 m maximum for RS-485 and 15 m maximum
for RS-232C communications. To extend the communications distance for
RS-232C communications, use OMROM's Z3R Optical Interface.
The wrong communications cable has been E5CN, E5EN, or E5AN: Use a shielded, AWG24 to AWG14 (cross-sec-
used. tional area of 0.205 to 2.081 mm2) twisted-pair cable for the communica-
tions cable.
E5GN: Use a shielded, AWG24 to AWG18 (cross-sectional area of 0.205
to 0.823 mm2) twisted-pair cable for the communications cable.
More than the specified number of communi- When 1:N RS-485 communications are used, a maximum of 32 nodes
cations devices are connected to the same (including the host node) can be connected.
communications path for RS-485 communi-
cations.
An end node has not been set at each end of Set or connect terminating resistance at each end of the line. If the E5CN,
the communications line for RS-485 commu- E5AN, E5EN, or E5GN is the end node, use 120- (1/2-W) terminating
nications. resistance. The combined terminating resistance with the host device
must be at least 54 .
The specified power supply voltage is not Supply the specified power supply voltage.
being supplied to the Controller.
The specified power supply voltage is not Supply the specified power supply voltage.
being supplied to an Interface Converter
(such as the K3SC).
The same baud rate and communications Set the same values for the baud rate, protocol, data length, stop bits, and
method are not being used by all of the Con- parity on all nodes.
trollers, host devices, and other devices on
the same communications line.
The unit number specified in the command Use the same unit number.
frame is different from the unit number set by
the Controller.
The same unit number as the Controller is Set each unit number for only one node.
being used for another node on the same
communications line for RS-485 communica-
tions.
There is a mistake in programming the host Use a line monitor to check the commands. Check operation using a sam-
device. ple program.
The host device is detecting the absence of a Shorten the send data wait time in the Controller or increase the response
response as an error before it receives the wait time in the host device.
response from the Controller.
The host device is detecting the absence of a The Controller does not return responses for broadcast commands.
response as an error after broadcasting a
command (except for SYSWAY).
The host device sent another command The response must always be read after sending a command (except for
before receiving a response from the Control- broadcast commands).
ler.
The host device sent the next command too After receiving a response, wait at least 2 ms before sending the next
soon after receiving a response from the command.
Controller.
286
Appendix
Meaning Countermeasures
The communications line became unstable Initialize the reception buffer in the host device before sending the first
when Controller power was turned ON or command and after turning OFF the power to the Controller.
interrupted, and the host device read the
unstable status as data.
The communications data was corrupted Try using a slower baud rate.
from noise from the environment. Separate the communications cable from the source of noise.
Use a shielded, twisted-pair cable for the communications cable.
Use as short a communications cable as possible, and do not lay or loop
extra cable.
To prevent inductive noise, do not run the communications cable parallel
to a power line.
If noise countermeasures are difficult to implement, use an Optical Inter-
face.
Note For details on errors, refer to E5CN/E5AN/E5EN/E5GN Digital Temperature Controllers Communica-
tions Manual Basic Type (Cat. No. H158).
287
Appendix
Parameter Operation Lists

Universal input: Controllers with Thermocouple/Resistance Thermometer Universal Inputs
Analog input: Controllers with Analog Inputs
Operation Level
Parameters Characters Setting (monitor) value Display Default Unit Set value
Process Value Temperature: According to EU
indication range for each sen-
sor.
Analog: Scaling lower limit
5% FS to Scaling upper limit
+5% FS
Set Point SP lower limit to SP upper 0 EU
limit
Auto/Manual Switch a-m
Multi-SP Set Point m-sp 0 to 3 0 None
Setting
Set Point During SP sp-m SP lower limit to SP upper EU
Ramp limit
Heater Current 1 ct1 0.0 to 55.0 A
Value Monitor
Value Monitor
Leakage Current 1 lcr1 0.0 to 55.0 A
Monitor
Monitor
Program Start prst RSET, STRT rset, strt RSET None
Soak Time Remain sktr 0 to 9999 min or h
RUN/STOP r-s RUN/STOP run, stop Run None
Alarm Value 1 al-1 1999 to 9999 0 EU
Alarm Value Upper al1h 1999 to 9999 0 EU
Limit 1
Alarm Value Lower al1l 1999 to 9999 0 EU
Limit 1
Limit 2
Limit 2
Limit 3
Limit 3
MV Monitor (Heat- o 5.0 to 105.5 (standard) %
ing) 0.0 to 105.0 (heating/cooling)
MV Monitor (Cool- c-o 0.0 to 105.0 %
ing)
288
Appendix
Adjustment Level
Adjustment Level l.adj
Display
AT Execute/Cancel at OFF, AT Cancel off, OFF None
AT-2: 100%AT Execute at-2,
AT-1: 40%AT Execute at-1
Communications cmwt OFF, ON off, on OFF None
Writing
Value Monitor
Heater Burnout hb1 0.0 to 50.0 0.0 A
Detection 1
Heater Overcurrent oc1 0.0 to 50.0 50.0 A
Detection 1
Value Monitor
Heater Burnout hb2 0.0 to 50.0 0.0 A
Detection 2
Heater Overcurrent oc2 0.0 to 50.0 50.0 A
Detection 2
Monitor
HS Alarm 1 hs1 0.0 to 50.0 50.0 A
Monitor
HS Alarm 2 hs2 0.0 to 50.0 50.0 A
SP 0 sp-0 SP lower limit to SP upper 0 EU
limit
limit
limit
limit
Temperature Input ins 199.9 to 999.9 0.0 C or F
Shift
Upper Limit Temper- insh 199.9 to 999.9 0.0 C or F
ature Input Shift
Value
Lower Limit Temper- insl 199.9 to 999.9 0.0 C or F
ature Input Shift
Value
Proportional Band p Universal input: 0.1 to 999.9 8.0 C or F
(See note
1.)
Analog input: 0.1 to 999.9 10.0 %FS
Integral Time i 0 to 3,999 233 Second
Derivative Time d RT OFF: 0 to 3,999 40 Second
RT ON: 0.0 to 999.9 40.0 Second
Cooling Coefficient c-sc 0.01 to 99.99 1.00 None
Dead Band c-db Universal input: 199.9 to 0.0 C or F
999.9 (See note
1.)
289
Appendix
Manual Reset Value of-r 0.0 to 100.0 50.0 %
Hysteresis (Heating) hys Universal input: 0.1 to 999.9 1.0 C or F
(See note
1.)
Hysteresis (Cooling) chys Universal input: 0.1 to 999.9 1.0 C or F
(See note
1.)
Soak Time soak 1 to 9,999 1 min or h
Wait Band wt-b Universal input: OFF, 0.1 to off, 0.1 to OFF C or F
999.9 999.9 (See note
1.)
Analog input: OFF, 0.01 to off, 0.01 to OFF %FS
99.99 99.99
MV at Stop mv-s 5.0 to 105.0 (standard) 0.0 %
ing)
MV at PV Error mv-e 5.0 to 105.0 (standard) 0.0 %
ing)
SP Ramp Set Value sprt OFF or 1 to 9,999 off, 1 to OFF EU/s, EU/
9999 min, EU/h
MV Upper Limit ol-h MV lower limit +0.1 to 105.0 105.0 %
(standard)
0.0 to 105.0 (heating/cooling)
MV Lower Limit ol-l 5.0 to MV upper limit 0.1 5.0 (stan- %
(standard) dard)
105.0 to 0.0 (heating/cool- 105.0
ing) (heating/
cooling)
MV Change Rate orl 0.0 to 100.0 0.0 %/s
Limit (0.0: MV Change Rate Limit
Disabled)
Extraction of Square sqrp 0.0 to 100.0 0.0 %
Root Low-cut Point
290
Appendix

Input Type in-t Multi- 0: Pt100 5 None
input 1: Pt100
2: Pt100
3: JPt100
4: JPt100
5: K
6: K
7: J
8: J
9: T
10: T
11: E
12: L
13: U
14: U
15: N
16: R
17: S
18: B
19: 10 to 70C
20: 60 to 120C
21: 115 to 165C
22: 160 to 260C
23: 0 to 50 mV
24: W
25: PLII
Analog 0: 4 to 20 mA 0 None
input 1: 0 to 20 mA
2: 1 to 5 V
3: 0 to 5 V
4: 0 to 10 V
Scaling Upper Limit in-h Scaling lower limit + 1 to 100 None
9,999
Scaling Lower Limit in-l 1,999 to scaling upper limit 0 None
1
Decimal Point dp Universal input: 0 to 1 0 None
Analog input: 0 to 3 0 None
Temperature Unit d-u C, F c, f C None
SP Upper Limit sl-h SP lower limit + 1 / input 1300 EU
range lower limit (tempera-
ture)
SP lower limit + 1 / scaling 100
upper limit (analog)
SP Lower Limit sl-l Input range lower limit to SP 200 EU
upper limit 1 (temperature)
Scaling lower limit to SP 0
upper limit 1 (analog)
PID ON/OFF intl ON/OFF 2-PID onof, pid ON/OFF None
Standard or Heating/ s-hc Standard or heating/cooling stnd, h-c Standard None
Cooling
ST st OFF, ON off, on ON None
Program Pattern ptrn OFF, STOP, CONT off, stop, OFF None
cont
Control Period cp 0.5 or 1 to 99 0.5, 1 to 99 20 Second
(Heating)
Control Period (Cool- c-cp 0.5 or 1 to 99 0.5, 1 to 99 20 Second
ing)
291
Appendix
Direct/Reverse orev Reverse operation, direct or-r, or-d Reverse None
Operation operation operation
Alarm 1Type alt1 0: Alarm function OFF 2 None
1: Upper and lower-limit
alarm
2: Upper-limit alarm
3: Lower-limit alarm
range alarm
alarm with standby
sequence
6: Upper-limit alarm with
standby sequence
7: Lower-limit alarm with
standby sequence
8: Absolute-value upper-limit
alarm
9: Absolute-value lower-limit
alarm
10: Absolute-value upper-limit
alarm with standby
sequence
11: Absolute-value lower-limit
alarm with standby
sequence
12: LBA (Loop Burnout Alarm)
13: PV change rate alarm
Alarm 1 Hysteresis alh1 Universal input: 0.1 to 999.9 0.2 C or F
(See note
1.)
Alarm 2 Type alt2 Same settings as the alarm 1 2 None
type.
Note The 12: LBA (Loop
Burnout Alarm) setting
cannot be used.
(See note
1.)
Alarm 3 Type alt3 Same settings as the alarm 2 2 None
type
(See note
1.)
Transfer Output Type tr-t OFF: OFF off OFF None
SP: Set point sp
SP-M: Ramp set point sp-m
PV: Process value pv
MV: Manipulated variable mv
(heating)
C-MV: Manipulated variable c-mv
(cooling)
Transfer Output tr-h See note 2. See note 2. See note 2.
Upper Limit
Transfer Output tr-l See note 2. See note 2. See note 2.
Lower Limit
292
Appendix
Linear Current Out- o1-t 4-20: 4 to 20 mA 4-20, 0-20 4-20 None
put 0-20: 0 to 20 mA
Multi-SP Use ev-m 0 to 2 1 None
Event Input Assign- ev-1 None: None none NONE None
ment 1 STOP: RUN/STOP stop
MANU: Auto/Manual manu
PRST: Program Start (See prst
note 3.)
DRS: Invert Direct/Reverse drs
Operation
AT-2: 100% AT Execute/Can- at-2
cel
AT-1: 40% AT Execute/Cancel at-1
WTPT: Setting Change wtpt
Enable/Disable
LAT: Alarm Latch Cancel lat
Event Input Assign- ev-2 None: None none STOP None
ment 2 STOP: RUN/STOP stop
MANU: Auto/Manual manu
PRST: Program Start (See prst
note 3.)
DRS: Invert Direct/Reverse drs
Operation
AT-2: 100% AT Execute/Can- at-2
cel
AT-1: 40% AT Execute/Cancel at-1
WTPT: Setting Change wtpt
Enable/Disable
Extraction of Square sqr OFF, ON off, OFF None
Root Enable on
Move to Advanced amov 1999 to 9,999 0 None
function Setting
Level
Note (1) Set None as the unit for analog inputs (23: 0 to 50 mV).
(2)
Transfer output Setting (monitor) range Default (transfer output Unit
type upper/lower limits)
(See note 2.1.)
Set Point SP lower limit to SP upper limit SP upper limit/lower limit EU
Set Point During SP SP lower limit to SP upper limit SP upper limit/lower limit EU
Ramp
PV Temperature: Input setting Input setting range upper/ EU
range lower limit to input setting lower limit
range upper limit
Analog: Scaling lower limit to Scaling upper/lower limit EU
scaling upper limit
MV Monitor (Heat- Standard: 5.0 to 105.0 100.0/0.0 %
ing) Heating/cooling: 0.0 to 105.0
MV Monitor (Cool- 0.0 to 105.0 100.0/0.0 %
ing)
(2.1) Initialized when the transfer output type is changed.

Initialized if the input type, temperature unit, scaling upper/lower limit, or SP upper/
lower limit is changed when the transfer output type is SP, ramp SP, or PV.
(When initialized by the initializing settings, it is initialized to 100.0/0.0.)
(3) PRST (Program Start) can be set even when the Program Pattern parameter is set to OFF, but the
function will be disabled.
293
Appendix

Manual MV 5.0 to 105.0 (standard) (See 0.0 %
note.)
ing) (See note.)
Note When the Manual MV Limit Enable parameter is set to ON, the setting range will be the MV lower limit to
the MV upper limit.
Monitor/Setting Item Level

The contents displayed vary depending on the Monitor/Setting 1 to 5 (advanced function setting level) setting.

Parameter Initializa- init OFF, FACT off, fact OFF None
tion
Multi-SP Uses mspu OFF, ON off, on OFF None
SP Ramp Time Unit spru S: EU/second s M None
M: EU/minute m
H: EU/hour h
Standby Sequence rest Condition A, condition B a, b Condition A None
Reset
HB ON/OFF hbu OFF, ON off, on ON None
Auxiliary Output 1 sb1n N-O: Close in alarm n-o, n-c N-O None
Open in Alarm N-C: Open in alarm
Heater Burnout hbl OFF, ON off, on OFF None
Latch
Heater Burnout Hys- hbh 0.1 to 50.0 0.1 A
teresis
ST Stable Range st-b 0.1 to 999.9 15.0 C or F
alfa 0.00 to 1.00 0.65 None
AT Calculated Gain at-g 0.1 to 10.0 0.8 None
AT Hysteresis at-h Universal input: 0.1 to 999.9 0.8 C or F
(See note
1.)
Limit Cycle MV lcma 5.0 to 50.0 20.0 %
Amplitude
Input Digital Filter inf 0.0 to 999.9 0.0 Second
Additional PV Dis- pvad OFF, ON off, on OFF None
play
MV Display o-dp OFF, ON off, on OFF None
Automatic Display ret OFF or 1 to 99 off, 1 to OFF Second
Return Time 99
Alarm 1 Latch a1lt OFF, ON off, on OFF None
Move to Protect prlt 1 to 30 3 Second
Level Time
Input Error Output sero OFF, ON off, on OFF None
294
Appendix
Cold junction Com- cjc OFF, ON off, on ON None
pensation Method
MB Command Logic rlrv OFF, ON off, on OFF None
Switching
PV Change Color colr Orange, Red, Green org, red, RED None
grn
Red to Green: When ALM1 is r-g
lit,
Green to Red: When ALM1 is g-r
lit
Red to Green to Red r-g.r
Within PV stable band:
Green
Outside stable band: Red
Green to Orange to Red g-o.r
Green
Outside stable band: Green,
Red
Orange to Green to Red o-g.r
Green
Outside stable band: Green,
Red
PV Stable Band pv-b Universal input: 0.1 to 999.9 5.0 C or F
(See note
1.)
Alarm 1 ON Delay a1on 0 to 999 (0: ON delay dis- 0 Second
abled)
abled)
abled)
Alarm 1 OFF Delay a1of 0 to 999 (0: OFF delay dis- 0 Second
abled)
abled)
abled)
Input Shift Type istp INS1: Temperature input 1- ins1, ins2 INS1 None
point shift
INS2: Temperature input 2-
point shift
MV at Stop and Error mvst OFF, ON off, on OFF None
Addition
Auto/Manual Select amad OFF, ON off, on OFF None
Addition
RT rt OFF, ON off, on OFF None
HS Alarm Use hsu OFF, ON off, on ON None
HS Alarm Latch hsl OFF, ON off, on OFF None
HS Alarm Hysteresis hsh 0.1 to 50.0 0.1 A
LBA Detection Time lba 0 to 9999 (0: LBA function dis- 0 Second
abled)
LBA Level lbal Universal input: 0.1 to 999.9 8.0 C or F
(See note
1.)
295
Appendix
LBA Band lbab Universal input: 0.0 to 999.9 3.0 C or F
(See note
1.)
Control Output 1 out1 When control output 1 is a O None
Assignment voltage output (for driving
SSR) (See note 2.): none
NONE: No assignment o
O: Control output (heat-
ing) c-o
C-O: Control output (cool-
ing)
ALM1: Alarm 1 alm1
ALM2: Alarm 2 alm2
ALM3: Alarm 3 alm3
P.END: Program end output p.end
(See note 3.)
RALM: Control output ON/ ralm
OFF count alarm
(See note 4.)
WR1: Work bit 1 (See note 5.) wr1
When control output 1 is a
current output (See note 2.):
NONE: No assignment none
O: Control output (heat- o
ing)
C-O: Control output (cool- c-o
ing)
Control Output 2 out2 NONE: No assignment none NONE None
Assignment O: Control output (heat- o
ing)
ing)
ALM1: Alarm 1 alm1
ALM2: Alarm 2 alm2
ALM3: Alarm 3 alm3
(See note 3.)
OFF count alarm
(See note 4.)
296
Appendix
Auxiliary Output 1 sub1 NONE: No assignment none ALM1 None
Assignment O: Control output (heat- o
ing)
ing)
ALM1: Alarm 1 alm1
ALM2: Alarm 2 alm2
ALM3: Alarm 3 alm3
(See note 3.)
OFF count alarm
(See note 4.)
Auxiliary Output 2 sub2 Same as for control output 1. ALM2 None
Assignment
Auxiliary Output 3 sub3 Same as for control output 1. ALM3 None
Assignment (E5AN/
E5EN only)
Character Select csel OFF, ON off, on ON None
Soak Time Unit t-u M: Minutes; H: Hours m, h M None
Alarm SP Selection alsp SP-M: Ramp set point sp-m, sp SP-M None
SP: Set point
Manual MV Limit manl OFF, ON off, on ON None
Enable
PV Rate of Change pvrp 1 to 999 4 Sampling
Calculation Period period
Automatic Cooling csca OFF, ON off, on OFF None
Coefficient Adjust-
ment
Heater Overcurrent ocu OFF, ON off, on ON None
Use
Heater Overcurrent ocl OFF, ON off, on OFF None
Latch
Heater Overcurrent och 0.1 to 50.0 0.1 A
Hysteresis
PF Setting pf OFF: OFF off A-M None
RUN: RUN run
STOP: STOP stop
R-S: RUN/STOP r-s
AT-2: 100% AT execute/cancel at-2
AT-1: 40% AT execute/cancel at-1
A-M: Auto/manual a-m
PFDP: Monitor/setting item pfdp
297
Appendix
Monitor/Setting Item pfd1 0: Disabled 1 None
1 1: PV/SP/Multi-SP
2: PV/SP/MV
3: PV/SP/Soak time remain
4: Proportional band (P)
5: Integral time (I)
6: Derivative time (D)
7: Alarm value 1
8: Alarm value upper limit 1
9: Alarm value lower limit 1
10: Alarm value 2
13: Alarm value 3
Monitor/Setting Item pfd2 0 to 15: Same as for Monitor/ 0 None
2 Setting Item 1.
3 Setting Item 1.
4 Setting Item 1.
5 Setting Item 1.
PV/SP Display spdp 0: PV/SP 4 None
Screen Selection 1: PV/SP/Multi-SP, PV/SP/MV
2: PV/SP/MV, PV/SP/Multi-SP
3: PV/SP/Multi-SP
4: PV/SP/MV
5: PV/SP/Multi-SP, PV/SP/
Soak Time Remain
6: PV/SP/MV, PV/SP/Soak
Time Remain
7: PV/SP/Soak Time Remain
MV Display Selec- odsl O: MV (Heating) o 0 None
tion C-O: MV (Cooling) c-o
PV Decimal Point pvdp OFF, ON off, on ON None
Display
PV Status Display pvst OFF: OFF off OFF None
Function MANU: Manual manu
STOP: Stop stop
ALM1: Alarm 1 alm1
ALM2: Alarm 2 alm2
ALM3: Alarm 3 alm3
ALM: Alarm 1 to 3 OR status alm
HA: Heater alarm ha
SV Status Display svst OFF: OFF off OFF None
Function MANU: Manual manu
STOP: Stop stop
ALM1: Alarm 1 alm1
ALM2: Alarm 2 alm2
ALM3: Alarm 3 alm3
ALM: Alarm 1 to 3 OR status alm
HA: Heater alarm ha
Display Refresh d.ref OFF, 0.25, 0.5, 1.0 0.25 Second
Period
Control Output 1 ON/ ra1m 0 to 9999 100 times
OFF Count Monitor
Control Output 2 ON/ ra2m 0 to 9999 100 times
OFF Count Monitor
298
Appendix
Control Output 1 ON/ ra1 0 to 9999 0 100 times
OFF Count Alarm
Set Value
Control Output 2 ON/ ra2 0 to 9999 0 100 times
OFF Count Alarm
Set Value
ON/OFF Counter rac 0: Disable the counter reset 0 None
Reset function.
ON/OFF counter.
ON/OFF counter.
Move to Calibration cmov 1999 to 9,999 0 None
Level
Note (1) Set None as the unit for analog inputs (23: 0 to 50 mV).
(2) The setting range depends on whether control output 1 is a current output or voltage output (for driv-
ing SSR).
(3) P.END (program end output) can be set even when the program pattern is set to OFF, but the func-
tion will be disabled.
(4) Turns ON when either the control output 1 or 2 ON/OFF count alarm is ON.
(5) Displayed when logic operations are used. For detail, refer to 4-22 Logic Operations.
Protect Level
Move to Protect level pmov 1999 to 9,999 0 None
Operation/Adjustment Protect oapt 0 to 3 0 None
Initial Setting/Communica- icpt 0 to 2 1 None
tions Protect
Setting Change Protect wtpt OFF, ON off, on OFF None
PF Key Protect pfpt OFF, ON off, on OFF None
Parameter Mask Enable pmsk OFF, ON off, on ON None
Password to Move to Protect prlp 1999 to 9,999 0 None
Level
Communications Setting Level

Protocol Setting psel CompoWay/F (SYSWAY), cwf, mod Compo- None
Modbus (See note.) Way/F
(SYSWAY)
Communications Unit No. u-no 0 to 99 1 None
Communications Baud bps 1.2, 2.4, 4.8, 9.6, 19.2, 38.4, 1.2, 2.4, 9.6 kbps
Rate or 57.6 4.8, 9.6,
19.2, 38.4,
57.6
Communications Data len 7, 8 7 Bit
Length
Communications Stop sbit 1, 2 2 Bit
Bits
Communications Parity prty None, Even, Odd none, Even None
even, odd
Send Data Wait Time sdwt 0 to 99 20 ms
Note When setting CWF, either CompoWay/F or SYSWAY can be used as the communications protocol.
(CompoWay/F and SYSWAY are automatically identified by the command frames.)
299
Appendix
Initialization According to Parameter Changes

The parameters that are initialized when parameters are changed are shown under Related initialized parame-
ters.
Changed Input Tem- Scaling SP Stan- Pro- Trans- Num- RT SP0 to
parameter type pera- Lower Lower dard or gram fer Out- ber of SP3
Related initial- ture Limit Limit Heat- Pattern put Multi- Set
ized parame- unit Scaling SP ing/ Type SP Point
ters Upper Upper Cooling Uses
Limit Limit
Related param- Tem- Analog
eter initializa- pera- input
tion execution ture
condition input
SP Upper Limit (See (See (See --- --- --- --- --- --- ---
SP Lower Limit note 1.) note 1.) note 1.)
Set Point (See (See (See (See --- --- --- --- --- (See
note 2.) note 2.) note 2.) note 2.) note
11.)
SP0 to SP3 (See (See (See (See --- --- --- --- --- (See
note 2.) note 2.) note 2.) note 2.) note
11.)
RT (See --- --- --- --- --- --- --- --- ---
note 3.)
Proportional (See --- --- --- --- --- --- --- (See ---
Band (See note note 3.) note 9.)
10.)
Integral Time (See --- --- --- --- --- --- --- (See ---
(See note 10.) note 3.) note 9.)
Derivative Time (See --- --- --- --- --- --- --- (See ---
(See note 10.) note 3.) note 9.)
MV Upper Limit, --- --- --- --- (See --- --- --- --- ---
MV Lower Limit note 5.)
MV at Stop --- --- --- --- --- --- --- --- ---
MV at PV Error --- --- --- --- --- --- --- --- ---
Manual MV --- --- --- --- --- --- --- --- --- ---
Transfer Output (See (See (See (See (See --- (See --- --- ---
Upper Limit, note 4- note 4- note 4- note 4- note 4- note 4-
Transfer Output 1.) 1.) 1.) 1.) 2.) 3.)
Lower Limit
(See note 4.)
Control Output 1 --- --- --- --- --- --- --- ---
Assignment
Control Output 2 --- --- --- --- (See (See --- --- --- ---
Assignment note 6.) note 6.)
Auxiliary Output --- --- --- --- (See (See --- --- --- ---
1 Assignment note 7.) note 7.)
Event Input --- --- --- --- --- (See --- (See --- ---
Assignment 1 note 8.) note
12.)
Event Input --- --- --- --- --- (See --- (See --- ---
Assignment 2 note 8.) note
12.)
300
Appendix
Changed Input Tem- Scaling SP Stan- Pro- Trans- Num- RT SP0 to

parameter type pera- Lower Lower dard or gram fer Out- ber of SP3
Related initial- ture Limit Limit Heat- Pattern put Multi- Set
ized parame- unit Scaling SP ing/ Type SP Point
ters Upper Upper Cooling Uses
Limit Limit
Related param- Tem- Analog
eter initializa- pera- input
tion execution ture
condition input
Move to Protect --- --- --- --- --- --- --- --- --- ---
Level
MV Display --- --- --- --- --- --- --- --- ---
Selection
Temperature --- --- --- --- --- --- --- --- --- ---
Input Shift
Upper Limit --- --- --- --- --- --- --- --- --- ---
Temperature
Input Shift,
Lower Limit
Temperature
Input Shift
Dead Band --- --- --- --- --- --- --- --- --- ---
Hysteresis --- --- --- --- --- --- --- --- --- ---
(Heating)
Hysteresis --- --- --- --- --- --- --- --- --- ---
(Cooling)
Wait Band --- --- --- --- --- --- --- --- --- ---
Alarm 1 to 3 --- -- --- --- --- --- --- --- --- ---
Hysteresis
ST Stable --- --- --- --- --- --- --- --- --- ---
Range
AT Hysteresis --- (See --- --- --- --- --- --- ---
note
13.)
PV Stable Band --- --- --- --- --- --- --- --- ---
LBA Level --- --- --- --- --- --- --- --- ---
LBA Band --- --- --- --- --- --- --- --- ---
Note (1) Initialized to input setting range upper and lower limits, or scaling upper and lower limits.
(2) Clamped by SP upper and lower limits.
(3) Initialized only when the input type is changed to analog input when RT turns ON. The defaults are
as follows:
RT: OFF
Proportional band: 8.0
Integral time: 233
Derivative time: 40
(4) Initialization is performed as shown below according to the transfer output type setting. The initial-
ization differs depending on the changed parameter and the output type setting.
SP: SP upper and lower limits
Ramp SP: SP upper and lower limits
PV: Input setting range upper and lower limits or scaling upper and lower limits
MV (Heating): 100.0/0.0
MV (Cooling): 100.0/0.0
(4-1) Initialized only when the transfer output type is set to SP, Ramp SP, or PV.
(4-2) Initialized only when the transfer output type is set to MV (Heating) or MV (Cooling).
301
Appendix
(4-3) Initialized to the above default values regardless of the settings for changing the transfer out-
put type.
(5) Initialized as follows according to the Standard or Heating/Cooling parameter setting.
MV Upper Limit: 105.0
MV Lower Limit: Standard 5.0, heating/cooling 105.0
(6) Initialized to control output (cooling) for heating and cooling control, according to the following.
(The defaults for standard control are the defaults in the parameter list.)
With control output 2: The Control Output 2 Assignment parameter is initialized to control output
(cooling).
Without control output 2 and E5AN/EN: The Auxiliary Output 3 Assignment parameter is initialized
to control output (cooling).
Without control output 2 and E5CN: The Auxiliary Output 2 Assignment parameter is initialized to
control output (cooling).
E5GN: The Auxiliary Output 1 Assignment parameter is initialized to control output (cooling).
(7) When the program pattern is OFF, the Auxiliary Output 1 Assignment parameter is initialized to
alarm output 1. When the program pattern is not OFF, the Auxiliary Output 1 Assignment parameter
is initialized to program end output. The Auxiliary Output 1 Assignment parameter is not initialized
for the E5GN, however, if it is set for heating/cooling control.
(8) If the Program Start parameter is assigned when the program pattern is changed to OFF, the Pro-
gram Start parameter will be initialized to not assigned.
(9) Initialized when temperature inputs are used and RT is changed. The defaults are as follows:
Proportional band: 8.0
Integral time: 233
Derivative time: 40 when RT is OFF, and 40.0 when RT is ON.
(10) The proportional band, integral time, and derivative time are initialized as follows by RT and input
type changes.
When RT is turned from ON to OFF by a change from temperature input to analog input.
When ON is turned to OFF or OFF is turned to ON by an RT change.
(11) Write to both so that the SP and the currently selected Multi-SP SP0 to SP3 match.
(12) Initializes event input assignments used for Multi-SP to NONE.
(13) Initialized to 0.8 when the temperature unit is C, and to 1.4 when the temperature unit is F.
302
Appendix
Sensor Input Setting Range, Indication Range, Control Range

Input type Specifications Set value Input setting range Input indication range
Control- Resistance ther- Pt100 0 200 to 850 (C)/300 to 220 to 870 (C)/340 to
lers with mometer 1,500 (F) 1,540 (F)
Thermo- 1 199.9 to 500.0 (C)/199.9 199.9 to 520.0 (C)/199.9
couple/ to 900.0 (F) to 940.0 (F)
Resis-
tance 2 0.0 to 100.0 (C)/0.0 to 210.0 20.0 to 120.0 (C)/40.0 to
Ther- (F) 250.0 (F)
mome- JPt100 3 199.9 to 500.0 (C)/199.9 199.9 to 520.0 (C)/199.9
ter Multi- to 900.0 (F) to 940.0 (F)
inputs 4 0.0 to 100.0 (C)/0.0 to 210.0 20.0 to 120.0 (C)/40.0 to
(F) 250.0 (F)
Thermocouple K 5 200 to 1,300 (C)/300 to 220 to 1,320 (C)/340 to
2,300 (F) 2,340 (F)
6 20.0 to 500.0 (C)/0.0 to 40.0 to 520.0 (C)/40.0 to
900.0 (F) 940.0 (F)
J 7 100 to 850 (C)/100 to 120 to 870 (C)/140 to
1,500 (F) 1,540 (F)
8 20.0 to 400.0 (C)/0.0 to 40.0 to 420.0 (C)/40.0 to
750.0 (F) 790.0 (F)
T 9 200 to 400 (C)/300 to 700 220 to 420 (C)/340 to 740
(F) (F)
10 199.9 to 400.0 (C)/199.9 199.9 to 420.0 (C)/199.9
to 700.0 (F) to 740.0 (F)
E 11 200 to 600 (C)/300 to 220 to 620 (C)/340 to
1,100 (F) 1,140 (F)
L 12 100 to 850 (C)/100 to 120 to 870 (C)/140 to
1,500 (F) 1,540 (F)
U 13 200 to 400 (C)/300 to 700 220 to 420 (C)/340 to 740
(F) (F)
14 199.9 to 400.0 (C)/199.9 199.9 to 420.0 (C)/199.9
to 700.0 (F) to 740.0 (F)
N 15 200 to 1,300 (C)/300 to 220 to 1,320 (C)/340 to
2,300 (F) 2,340 (F)
R 16 0 to 1,700 (C)/0 to 3,000 20 to 1,720 (C)/40 to
(F) 3,040 (F)
S 17 0 to 1,700 (C)/0 to 3,000 20 to 1,720 (C)/40 to
(F) 3,040 (F)
B 18 100 to 1,800 (C)/300 to 0 to 1,820 (C)/0 to 3,240
3,200 (F) (F)
ES1B Infrared 10 to 70C 19 0 to 90 (C)/0 to 190 (F) 20 to 130 (C)/40 to 270
Temperature (F)
Sensor 60 to 120C 20 0 to 120 (C)/0 to 240 (F) 20 to 160 (C)/40 to 320
(F)
115 to 165C 21 0 to 165 (C)/0 to 320 (F) 20 to 205 (C)/40 to 400
(F)
140 to 260C 22 0 to 260 (C)/0 to 500 (F) 20 to 300 (C)/40 to 580
(F)
Analog input 0 to 50 mV 23 Any of the following ranges, 5% to 105% of setting
by scaling: range. The display shows -
1,999 to 9,999 1999 to 9999 (numeric range
199.9 to 999.9 with decimal point omitted).
Thermocouple W 24 0 to 2300 (C)/0 to 3200 (F) 20 to 2320 (C)/40 to 3240
(F)
PL-II 25 0 to 1300 (C)/0 to 2300 (F) 20 to 1320 (C)/40 to 2340
(F)
303
Appendix
Input type Specifications Set value Input setting range Input indication range
Control- Current input 4 to 20 mA 0 Any of the following ranges, 5% to 105% of setting
lers with 0 to 20 mA 1 by scaling: range. The display shows
Analog 1,999 to 9,999 1999 to 9999 (numeric
Inputs Voltage input 1 to 5 V 2 199.9 to 999.9 range with decimal point
0 to 5 V 3 19.99 to 99.99 omitted).
0 to 10 V 4 1.999 to 9.999
The default is 5 (C/F) for Controllers with Thermocouple/Resistance Thermometer Universal Inputs and 0
for Controllers with Analog Inputs.
The applicable standards for each of the above input ranges are as follows:
K, J, T, E, N, R, S, B: JIS C1602-1995, IEC 584-1
L: Fe-CuNi, DIN 43710-1985
U: Cu-CuNi, DIN 43710-1985
W: W5Re/W26Re, ASTM E988-1990
JPt100: JIS C 1604-1989, JIS C 1606-1989
Pt100: JIS C 1604-1997, IEC 751
PLII: According to Platinel II Electromotive Force Table by Engelhard Corp.
Control Range
Resistance thermometer and thermocouple input
Temperature lower limit 20C to temperature upper limit +20C, or temperature lower limit 40f to
temperature upper limit +40f
ES1B input:
Same as input indication range
Analog input
5% to +105% of scaling range
304
Appendix
Setting Levels Diagram

This diagram shows all of the setting levels. To move to the advanced function setting level and calibration
level, you must enter passwords. Some parameters are not displayed depending on the protect level setting
and the conditions of use.
Control stops when you move from the operation level to the initial setting level.
Power ON
Start in manual mode.
Start in automatic mode.
Press the O Key or the

PF Key for at least 1 s.
(See note 4.) Press the
Operation Adjustment O+ M
Level Level Press the Keys for at
O+ M least 1 s.
Press the Keys for at
a-m O Key less than 1 s. least 3 s.
(Display c
25
will flash
after 1st 100
PF Key second.)
Press the O Key (See note 5.)
Manual (See for at least 3 s while PF Key Monitor/Setting
a-m is displayed. (See note 5.)
mode note (a-m will flash after Item Level
3.) 1st second.)
(See note 4.)

Press the PF Key least 3 s. (Display will flash
Manual for at least 1 s. (See after 1st second.)
Control Level note 1.)
c
25
Press the 100
O Key for Control stops. Protect Level
at least 1 s.
Note The time taken to move
Communica- to the protect level can
Initial Setting be adjusted by chang-
tions Setting
Level ing the "Move to pro-
Level
Press the tect level time" setting.
O Key for less than 1 s.
(Refer to page 228.)
Input password while
Press the O Key amoV is displayed. (Set
for at least 1 s. value 169)
Advanced Function
Setting Level
Input password. Control in progress
Control stopped
(See Not displayed for some models

Calibration Level
note 2.)
Level change
Note (1) You can return to the operation level by executing a software reset.
(2) It is not possible to move to other levels from the calibration level by operating the keys on the front
panel. It can be done only by first turning OFF the power.
(3) From the manual control level, key operations can be used to move to the operation level only.
(4) When the PF Setting parameter is set to A-M for a Controller with a PF Key (E5AN/EN).
(5) When the PF Setting parameter is set to PFDP for a Controller with a PF Key (E5AN/EN)
305
Appendix
Parameter Flow
This section describes the parameters set in each level. Pressing the M Key at the last parameter in each level
returns to the top parameter in that level.
PF Key (See note 2.)

Power ON
Starting in manual mode.
Starting in Press the O Key for at least 3 s. PF Key (See note 2.)
Manual Control Level automatic Other than the Auto/Manual Switch display
mode.
Press the PF Key Press the O Initial Setting Level
for at least 1 s. PID Key or the PF
C
25 Control Key for at least Press the Press the O Key less than 1 s.
(See note 1.) only 1 s. O Key for
(See note 1.). at least 1 s.
PV/MV in-t Input Type
Press the O Key less than 1 s. 5
Adjustment M
Level Operation Level Scaling Upper Limit
in-h
Press the O Key less than 1 s. 100
C Process Value
r-s RUN/STOP M
25 Added when Additional
PV display is ON. run in-l Scaling Lower Limit
Adjustment Level 0
Display M M
Set either of these parameters.

l.adj
Displayed only C
ins Temperature Input Shift C
25 Process Value/ M
al-1 Alarm Value 1
C
once when
Set Point Decimal Point
entering
adjustment level.
0.0 0 0 dp
1-point shift 0 For input type of analog
M M M M
at
C Upper Limit
insh Temperature Set either M
AT Execute/Cancel of these a-m Auto/Manual Switch
PID control only.
C
al1h Alarm Value
Temperature Unit
off 0.0 Input Shift Value parameters. Added when auto/man-
Upper Limit 1
0 d-u C, F
Press the ual select addition is ON. c
M M 2-point shift
O Key M M
For input type of
temperature
cmwt Communications
C
insl Lower Limit for at M
Writing Temperature
least 3 s. m-sp Multi-SP
Set Point Setting
C
al1l Alarm Value
SP Upper Limit
sl-h
C
Lower Limit 1
off 0.0 Input Shift Value 0 0
M 1300
M M M

ct1 Heater Current 1 C
p Proportional Band M Limit the set point
sp-m Set Point During
C
Value Monitor SP Ramp
C
al-2 Alarm Value 2 SP Lower Limit
0.0 8.0 0 0
C
sl-l
M M -200
M M
hb1 Heater Burnout i Integral Time M
Detection 1 ct1 Heater Current 1 Value C
al2h Alarm Value
0.0 233
Monitor
0.0 0
Upper Limit 2 cntl PID ON/OFF
M PID settings onof
M M M
oc1 Heater Overcurrent
d Derivative Time Heater Current 2 Value Alarm Value M
Detection 1 ct2 Monitor
C
al2l Lower Limit 2 Standard or
50.0 40 0.0 0 s-hc Heating/Cooling
M M stnd
M M
ct2 Heater Current 2

c-sc Cooling Coefficient M
Value Monitor lcr1 Leakage Current 1 C
al-3 Alarm Value 3
0.0 1.00 Monitor
0.0 0 st ST (Self-tuning)
on For input type of
M M Heating/cooling
M M temperature, stand-
hb2 Heater Burnout C
c-db Dead Band M ard control, or PID
Detection 2 lcr2 Leakage
Monitor
Current 2 C
al3h Alarm Value
0.0 0.0 0.0
Upper Limit 3
0
ptrn Program Pattern
M off When assigning PID or

M M M control output to ON/OFF
of-r Manual Reset Value M
oc2 Heater Overcurrent
Detection 2 Clear the offset during prst Program Start C
al3l Alarm Value
Lower Limit 3
output
50.0 50.0 stabilization of P or PD
control. rset 0 cp Control Period (Heating)
M M M M 20
lcr1 Leakage Current 1
Monitor
C
hys Hysteresis (Heating) sktr Soak Time Remain o MV Monitor (Heating) M
Set the ON/OFF
output cycle.
0.0
0.0 1.0 0 0.0 c-cp Control Period (Cooling)
M M Hysteresis settings
M M 20
chys Hysteresis (Cooling)
C
hs1 HS Alarm 1
c-o MV Monitor (Cooling) M
50.0 1.0 0.0 orev Direct/Reverse Operation
M M M or-r
lcr2 Leakage Current 2
Monitor
soak Soak Time M
1 Press the O and M Keys for
0.0 Press the O Key Alarm 1 Type
at least 3 s. Press the O and M Keys for at least 1 s. less than 1 s.
alt1
M M 2
hs2 HS Alarm 2 C
wt-b Wait Band Communications
Protect Level Setting Level M
50.0 off Alarm 1
alh1
C
The time taken to move to the protect level Displayed only for models with communications.
M M can be adjusted by changing the "Move to Changes are effective after cycling power or after 0.2
Hysteresis
protect level time" setting.
C
sp-0 SP 0 mv-s MV at Stop a software reset.
M
0.0 Move to Protect Level:
0 pmov
M
Displayed only when a password
0 is set. Restricts moving to protect psel Protocol Setting:
Switches between
M MV at PV Error level. cwf CompoWay/F (SYS-
C
sp-1 SP 1 mv-e M WAY) and Modbus.
0.0 Operation/Adjustment Protect:
M
0
M
SP used by
multi-SP M oapt Restricts displaying and modi-
fying menus in operation, ad-
0 justment, and manual control 1
C
sp-2 SP 2
C
sprt SP Ramp Set Value levels.
0 off M Initial Setting/ M
Communications
M M icpt Communications Protect: bps Baud Rate Note:
This protect level restricts movement CompoWay/F
MV Upper Limit 1 to the initial setting, communications 9.6
C
sp-3 SP 3 ol-h (SYSWAY) only
1. When the PF Setting parameter is
105.0 M levels.
setting, and advanced function setting
M
0
wtpt Setting Change Protect: len Communications set to A-M for a Controller with a
M M Protects changes to setups by Data Length
ol-l MV Lower Limit off operating the front panel keys. 7 PF Key (E5AN/EN).
-5.0 M M
M pfpt PF Key Protect
Restricts PF key operation
sbit Communications
Stop Bits
2 2. When the PF Setting parameter is
orl MV Change Rate Limit off (E5AN/EN only)
0.0 M M set to PFDP for a Controller with a
M pmsk Parameter Mask Enable:
Displayed only when a parame-
prty Communications Parity PF Key (E5AN/EN).
on ter mask is set. even
Extraction of Square Root
sqrp Low-cut Point M M
0.0
prlp Password to Move to Protect Level:
Password setting sdwt Send Data Wait Time
M 0 20
M M
306
Appendix
Monitor/Setting Item Level (E5AN/EN only)
25
C
Monitor/Setting PF Monitor/Setting PF Monitor/Setting PF Monitor/Setting PF Monitor/Setting
Item Display 1 Item Display 2 Item Display 3 Item Display 4 Item Display 5
0
Note: The monitor/setting items to be displayed is set in the Monitor/Setting Item 1 to 5 parameters (advanced function setting level).
Press the O Key for at least 1 s.

Alarm 2 Type PF Setting

alt2 init Parameter Initialization a1lt Alarm 1 Latch hsu HS Alarm Use pf (E5AN/E5EN only)
2 off off on a-m
M M M M M
C
alh2 Alarm 2
a2lt Alarm 2 Latch hsl HS Alarm Latch pfd1 Monitor/Setting Item 1
Hysteresis
0.2
mspu Multi-SP Uses
off off 1
off
M M M M (E5AN/E5EN only)
M
alt3 Alarm 3 Type SP Ramp Time Unit a3lt Alarm 3 Latch hsh HS Alarm Hysteresis pfd2 Monitor/Setting Item 2
2 spru
m off 0.1 0
M M
Alarm 3 M M M
C
alh3 pfd3 Monitor/Setting Item 3
0.2
Hysteresis Standby Sequence
rest Reset prlt Move
Time
to Protect Level
lba LBA Detection Time
a 3 0 0
tr-t Transfer Output Type M M M M
off Linear output sb1n Auxiliary Output 1 sero Input Error Output
C
lbal LBA Level pfd4 Monitor/Setting Item 4
M n-o Open in Alarm off 8.0 0
tr-h Transfer Output
M M M
Upper Limit M
100.0 Cold Junction
cjc Compensation
C
lbab LBA Band pfd5 Monitor/Setting Item 5
sb2n Auxiliary Output 2
M n-o Open in Alarm on Method 3.0 0
tr-l Transfer Output
Lower Limit M M M M
0.0 MB Command "PV/SP" Display
sb3n Auxiliary Output 3 rlrv Logic Switching out1 Control Output 1
Assignment spdp Screen Selection
M n-o
Open in Alarm off o 4
o1-t Linear Current Output M M M M
4-20 Linear output
hbu HB ON/OFF colr PV Change Color out2 Control Output 2
Assignment odsl MV Display Selection
M red none o
on
ev-m Number of Multi-SP Uses
Two SPs: 1
1 Four SPs: 2 M M M M
pv-b PV Stable Band pvdp PV Decimal Point
C
M hbl Heater Burnout Latch sub1 Auxiliary Output 1

Assignment Display
off 5.0 alm1 on
ev-1 Event Input
M M M
none
Assignment 1 M Auxiliary Output 2 PV Status Display
M hbh Heater Burnout
Hysteresis a1on Alarm 1 ON Delay sub2 Assignment pvst Function
0.1 0 alm2 off
ev-2 Event Input
Assignment 2
stop M M M M
Auxiliary Output 3 SV Status Display
M
C
st-b ST Stable Range a2on Alarm 2 ON Delay sub3 Assignment svst Function
15.0 0 alm3 (E5AN/E5EN only) off
sqr Extraction
Root Enable
of Square
off M M M M
alfa d.ref Display Refresh
M Move to Advanced Function a3on Alarm 3 ON Delay csel Character Select Period
amov Setting Level: 0.65 0 on 0.25
Displayed when initial set-
0 ting/communications pro- M M M M
tect is set to 0.
M at-g AT Calculated Gain a1of Alarm 1 OFF Delay t-u Soak Time Unit ra1m Control Output 1
ON/OFF Count
Move by setting password (169). 0.8 0 m 0 Monitor
M M M M
Control Output 2
C
at-h AT Hysteresis a2of Alarm 2 OFF Delay alsp Alarm SP Selection ra2m ON/OFF Count
0.8 0 sp-m 0 Monitor
M M M
M Control Output 1
lcma Limit Cycle MV
a3of Alarm 3 OFF Delay manl Manual MV ra1 ON/OFF Count
Limit Enable
Amplitude
0 0 Alarm Set Value
20.0 off
M M M M
istp Input Shift Type ra2 Control Output 2
inf Input Digital Filter pvrp PV Rate of Change ON/OFF Count
0 Alarm Set Value
ins1 Calculation Period
0.0 4
M M M
M
pvad Additional PV Display mvse MV at Stop and Error
Addition csca
Automatic Cooling rac ON/OFF
Reset
Counter
Coefficient Adjustment 0
off off off
M M M M
o-dp MV Display amad Auto/Manual
Addition
Select
ocu Heater Overcurrent cmov Move
Level
to Calibration
Use 0
off off on
M M M
M
ret Automatic Display rt RT ocl Heater Overcurrent
Return Time Latch
off off off
M M M
Heater Overcurrent
och Hysteresis
0.1
M
307
Appendix
308
Index
platinum resistance thermometer, 264

Numerics registering calibration data, 260
2-PID control, 54, 204 thermocouple, 260
user calibration, 260
voltage input, 268
A characteristics, 277
adjustment level, 16, 177 cold junction compensator
parameter operation list, 289 connecting, 261
advanced function setting level, 17, 218 communications
moving to, 108 operation commands, 112
parameter operation list, 294 wiring
RS-232C, 44
alarm delays, 116
RS-485, 42
alarms, 13
communications function, 14
alarm delays, 116
alarm hysteresis, 93 communications setting level, 17, 255
alarm latch, 94 parameter operation list, 299
alarm outputs, 69 control outputs, 13
alarm types, 69 control outputs 1 and 2
alarm values, 71 wiring, 37, 39
operation, 94 control periods, 54, 206
analog input, 94, 272 Controllers with Analog Input, 267
calibration, 265, 267 Controllers with Analog Inputs, 259, 268
AT (auto-tuning), 62 Controllers with Thermocouple/Resistance Thermometer
auto control, 103 Universal Input, 258, 265
auto/manual select addition, 124, 234 cooling coefficient
auto/manual switch, 166 setting, 98
auxiliary output 1 assignment, 240 current input
calibration, 267
auxiliary output 2 assignment, 241
current transformer
auxiliary output 3 assignment, 242
calculating detection current, 75
auxiliary outputs 1, 2 and 3, 40
Current Transformers (CT), 74, 279
wiring, 41
CT inputs
wiring, 42
B external dimensions, 279
E54-CT1, 279
basic model E54-CT3, 279
E5AN, 9 specifications, 278, 279
E5CN, 6 Current Value Exceeds (error display), 282
E5CN-U, 7
E5EN, 9
E5GN, 11 D
dead band, 97
C setting, 98
derivative time, 68
calibration
detection current, 75
analog input, 265, 267
current input, 267 dimensions, 22
indication accuracy, 270 E5AN, 22
input types, 260 E5CN, 22
309
Index
E5CN-U, 22 settings, 82
E5EN, 22 HS Alarm (error display), 283
E5GN, 23 hysteresis, 60, 62
direct operation, 55, 206
Display Range Exceeded (error display), 281
down key, 5 I
I/O configuration, 6
basic model
E E5AN, 9
error displays, 281 E5CN, 6
Current Value Exceeds, 282 E5CN-U, 7
Display Range Exceeded, 281 E5EN, 9
Heater Burnout, 283 E5GN, 11
Heater Overcurrent, 283 main functions, 12
HS Alarm, 283 indication accuracy, 270
Input Error, 281 indicators
Memory Error, 282 explanation, 4
event inputs, 13, 41, 99, 101 operation, 4
wiring, 41 infrared temperature sensor, 270
external dimensions initial setting level, 17, 199
Current Transformer (CT), 279 parameter operation list, 291
external power supply for ES1B, 14, 44, 90, 276 initial setting/communications protect, 110
initial settings, 50
examples, 50, 51
F initialization, 220
front panel Input Error (error display), 281
E5AN, 2 input sensor types, 12, 200
E5CN, 2
input shift, 89
E5CN-U, 2
one-point shift, 89
E5EN, 3
two-point shift, 90
E5GN, 3
calculating, 90
input types, 52, 303
default values, 200
H list, 53
HB alarm (heater burnout alarm), 73 setting, 52
settings, 80 inputs
Heater Burnout (error display), 283 wiring, 36
heater burnout alarm, 13, 276 installation, 22, 25
heater burnout hysteresis, 223 E5AN/E5EN
heater burnout latch, 223 mounting the terminal cover, 26
mounting to the panel, 26
heater overcurrent
E5CN/E5CN-U
hysteresis, 247
mounting the terminal cover, 26
latch, 246
heating/cooling control, 95, 189, 193, 204
E5GN
cooling coefficient, 97, 189
dead band, 97, 189
panel cutout
setting, 98
E5AN, 24
HS alarm, 13, 73, 276 E5CN, 24
310
Index
E5CN-U, 24 MV at PV error, 137, 233

E5EN, 24 MV at stop, 136, 233
E5GN, 25
removing from case
E5AN, 29 N
E5CN, 28
E5EN, 29 No. 1 display, 4
removing the terminal block No. 2 display, 4
E5GN, 30
integral time, 68, 188
O
ON/OFF control, 54, 204
K setting, 61
keys one-point shift, 91
down key, 5 operation level, 16, 163
key operations, 15 parameter operation list, 288
level key, 5 operation/adjustment protect, 110
mode key, 5 output functions
operations, 5 assignments, 56
up key, 5
output limits, 136
output periods, 206
L output specifications
setting, 54
LBA (loop burnout alarm), 118
band, 119
detection time, 119, 120 P
level, 119, 120
panel cutout
level key, 5
E5AN, 24
loop burnout alarm (LBA), 118
E5CN/E5CN-U, 24
E5EN, 24
E5GN, 25
M parameter flow, 305
main functions, 12 parameter operation list, 288
manual control, 103, 122 adjustment level, 289
manual control level, 16 manual control level, 294
moving to, 123 operation level, 288
parameter operation list, 294 parameter operation lists
manual setup, 68 advanced function setting level, 294
Memory Error (error display), 282 communications setting level, 299
initial setting level, 291
mode key, 5
protect level, 299
mounting, 25
parameter structure, 258
terminal cover
E5AN/E5EN, 26 parameters
E5CN/E5CN-U, 26 additional PV display, 226
to panel adjustment level display, 179
E5AN/E5EN, 26 alarm 1 hysteresis, 209
E5CN/E5CN-U, 25 alarm 1 latch, 227
E5GN, 27 alarm 1 OFF delay, 232
alarm 1 ON delay, 232
multi-SP, 101, 167
311
Index
alarm 1 type, 207 dead band, 189

alarm 2 hysteresis, 209 decimal point, 202
alarm 2 latch, 227 derivative time, 188
alarm 2 OFF delay, 232 direct/reverse operation, 206
alarm 2 ON delay, 232 display refresh period, 251
alarm 2 type, 209 event input assignment *, 216
alarm 3 hysteresis, 209 extraction of square root enable, 216
alarm 3 latch, 227 extraction of square root low-cut point, 194
alarm 3 OFF delay, 232 HB ON/OFF, 222
alarm 3 ON delay, 232 heater burnout detection 1, 181
alarm 3 type, 210 heater burnout detection 2, 183
alarm SP selection, 244 heater burnout hysteresis, 223
alarm value 1, 172 heater burnout latch, 223
alarm value 2, 173 heater current 1 value monitor, 168, 180
alarm value 3, 173 heater current 2 value monitor, 169, 182
alarm value lower limit 1, 174 heater overcurrent detection 1, 181
alarm value lower limit 2, 174 heater overcurrent detection 2, 183
alarm value lower limit 3, 175 heater overcurrent hysteresis, 247
alarm value upper limit 1, 174 heater overcurrent latch, 246
alarm value upper limit 2, 174 heater overcurrent use, 246
alarm value upper limit 3, 175 HS alarm 1, 184
alpha, 224 HS alarm 2, 185
AT calculated gain, 225 HS alarm hysteresis, 236
AT execute/cancel, 179 HS alarm latch, 235
AT hysteresis, 225 HS alarm use, 235
auto/manual select addition, 234 hysteresis (cooling), 190
auto/manual switch, 166 hysteresis (heating), 190
automatic cooling coefficient adjustment, 245 initial setting/communications protect, 160
automatic display return time, 227 input digital filter, 226
auxiliary output 1 assignment, 240 input error output, 228
auxiliary output 1 open in alarm, 222 input shift type, 233
auxiliary output 2 assignment, 241 input type, 200
auxiliary output 2 open in alarm, 222 integral time, 188
auxiliary output 3 assignment, 242 LBA band, 237
auxiliary output 3 open in alarm, 222 LBA detection time, 236
character select, 243 LBA level, 237
cold junction compensation method, 229 leakage current 1 monitor, 170, 184
communications baud rate, 255 leakage current 2 monitor, 170, 185
communications data length, 255 limit cycle MV amplitude, 225
communications parity, 255 linear current output, 212
communications stop bits, 255 lower-limit temperature input shift value, 187
communications Unit No., 255 manual MV limit enable, 244
communications writing, 180 manual reset value, 190
control output 1 assignment, 238 MB command logic switching, 229
control output 1 ON/OFF count alarm set value, 253 monitor/setting item *, 248
control output 1 ON/OFF count monitor, 252 monitor/setting item display 1 to 5, 196
control output 2 assignment, 239 move to advanced function setting level, 217
control output 2 ON/OFF count alarm set value, 253 move to calibration level, 254
control output 2 ON/OFF count monitor, 252 move to protect level, 160
control period (cooling), 206 move to protect level time, 228
control period (heating), 206 multi-SP set point setting, 167
cooling coefficient, 189 multi-SP uses, 220
312
Index
MV (manual MV), 197 ST (self-tuning), 205

MV at PV error, 192 ST stable range, 224
MV at stop, 192 standard or heating/cooling, 204
MV at stop and error addition, 233 standby sequence reset, 221
MV change rate limit, 194 SV status display function, 251
MV display, 227 temperature input shift, 186
MV display selection, 249 temperature unit, 202
MV lower limit, 193 transfer output lower limit, 212
MV monitor (cooling), 176 transfer output type, 210
MV monitor (heating), 175 transfer output upper limit, 212
MV upper limit, 193 upper-limit temperature input shift value, 187
number of multi-SP uses, 213 wait band, 191
ON/OFF counter reset, 254 part names, 2
operation/adjustment protect, 160 password, 111, 112
parameter initialization, 220
PID constants, 62, 65
parameter mask enable, 161
setting manually, 68
password to move to protect level, 162
PID control
PF key protect, 161
setting, 61
PF setting, 247
PID ON/OFF, 204 PID ON/OFF
process value, 165 Page, 193
process value/set point, 165 platinum resistance thermometer, 271
program pattern, 205 calibration, 264
program start, 171 power supply
proportional band, 188 wiring, 35
protocol setting, 255 precautions
PV change color, 230 wiring, 33
PV decimal point display, 250
process value (PV), 165
PV rate of change calculation period, 245
program end, 132
PV stable band, 231
output, 132
PV status display function, 250
PV/MV (manual MV), 197 program patterns, 130
PV/SP display screen selection, 249 proportional action, 68
RT, 234 proportional band, 68
RUN/STOP, 172 protect level, 16, 110, 159
scaling lower limit, 202 moving to, 112, 160, 228
scaling upper limit, 202 communications operation command, 112
selecting, 17 password, 111, 162
send data wait time, 255 parameter operation list, 299
set point during SP ramp, 167 protection, 110
setting change protect, 161 initial setting/communications, 110, 160
soak time, 191 operation/adjustment, 110, 160
soak time remain, 171 setting change, 110, 111
soak time unit, 243
PV display
SP 0, 186
color change, 113
SP 1, 186
stable band, 114
SP 2, 186
PV/MV, 197
SP 3, 186
SP lower limit, 203
SP ramp set value, 193
SP ramp time unit, 220
R
SP upper limit, 203 ratings, 275
313
Index
removing from case switching between SPs, 102

E5AN/E5EN, 29 shifting input values, 89
E5CN, 28 simple program function, 129, 135
removing the terminal block controlling start, 103
E5GN, 30 starting, 131
reverse operation, 55, 206 soak time, 131
RT (robust tuning), 66, 234 SP ramp, 106
run/stop control, 103 alarm operations, 108
operation at startup, 107
restrictions, 107
S specifications, 275
Current Transformer (CT), 278, 279
scaling
external power supply for ES1B, 45
upper and lower limits for analog inputs, 94
output, 54
screwless clamp terminals, 34
USB-Serial Conversion Cable, 280
self-tuning (ST), 64, 205
ST (self-tuning), 64
sensor input ST stable range, 65
control range, 303 startup conditions, 65
indication range, 303
standard control, 204
setting range, 303
standby sequence, 93
sensor types, 200
startup
set point (SP), 59
conditions, 65
limiter, 104
operation, 107
limiting change rate, 106
support software port, 45
lower limit, 106
ramp, 106
setting, 59, 61
setting upper and lower limits, 104
T
switching between SPs, 102 temperature input, 12, 13
upper limit, 105 shift values, 93
setting change protect, 110 temperature unit, 4, 54
setting level configuration, 15 terminals
setting levels arrangement
diagram, 305 E5AN/E5EN, 32
settings E5CN, 31
cooling coefficient, 98 E5CN-U, 32, 33
dead band, 98 wiring, 31
event input, 99 thermocouple, 270
HB alarm (heater burnout alarm), 80 calibration, 260
moving to advanced function setting level, 80 Thermocouple/Resistance Thermometer
heating/cooling control, 98 input type, 264, 265
HS alarm, 82 universal input type, 265
moving to advanced function setting level, 81, 82 three-position control, 60
hysteresis, 62
transfer output, 126
LBA detection time, 119
type, 127
password, 112
troubleshooting, 284
PID ON/OFF, 61
saving, 18 two-point shift, 90, 92, 93
SP lower limit, 106 calculating, 90
SP upper limit, 105
314
Index
U
up key, 5
USB-Serial Conversion Cable
specifications, 280
user calibration, 260
V
voltage input
calibration, 268
W
wait band, 131
wiring, 35
auxiliary outputs 1, 2, and 3, 40
communications
RS-232C, 44
RS-485, 42
control output 1, 37
control output 2, 39
CT inputs, 42
event inputs, 41
external power supply for ES1B, 44
inputs, 36
power supply, 35
precautions, 33
terminal arrangement, 31
terminals, 31
315
Index
316
Revision History
A manual revision code appears as a suffix to the catalog number on the front cover of the manual.
Cat. No. H156-E1-03
Revision code
The following table outlines the changes made to the manual during each revision. Page numbers refer to the
previous version.
Revision code Date Revised content
01 January 2008 Original production
01A March 2008 Page 9: Added case color information to the model number legend.
02 March 2009 Pages xii and xiv: Added information on shipping standards and corrected mis-
takes.
Pages 26, 96,236, 246, 255, 263, and 277: Made minor corrections.
Pages 62 to 67: Made minor corrections to graphics.
Page 80: Replaced graphic and changed step 2.
03 September 2009 Added the E5GN.
317
OMRON Corporation OMRON ELECTRONICS LLC
One Commerce Drive Schaumburg, Authorized Distributor:
Industrial Automation Company
IL 60173-5302 U.S.A.
Control Devices Division H.Q.
Tel: (1) 847-843-7900/Fax: (1) 847-843-7787
Industrial Component Division
2-2-1 Nishikusatsu, Kusatsu-shi,
Shiga, 525-0035 Japan OMRON ASIA PACIFIC PTE. LTD.
Tel: (81) 77-565-5160/Fax: (81) 77-565-5569 No. 438A Alexandra Road # 05-05/08 (Lobby 2),
Alexandra Technopark, Singapore 119967
Tel: (65) 6835-3011/Fax: (65) 6835-2711
Regional Headquarters OMRON (CHINA) CO., LTD.

OMRON EUROPE B.V. Room 2211, Bank of China Tower, OMRON Corporation 2008 All Rights Reserved.
Wegalaan 67-69-2132 JD Hoofddorp 200 Yin Cheng Zhong Road, In the interest of product improvement,
The Netherlands PuDong New Area, Shanghai, 200120, China specifications are subject to change without notice.
Tel: (31)2356-81-300/Fax: (31)2356-81-388 Tel: (86) 21-5037-2222/Fax: (86) 21-5037-2200 Printed in Japan
OMRON Industrial Automation Global: www.ia.omron.com Cat. No. H156-E1-03 0909

H156-E1-03 E5 - N UsersManual

Uploaded by

Copyright:

Available Formats

H156-E1-03 E5 - N UsersManual

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

H156-E1-03 E5 - N UsersManual

Uploaded by

Copyright:

Available Formats

What are the main functions and characteristics of these Digital Temperature Controllers?

What are the main functions and characteristics of these Digital Temperature Controllers?

What types of inputs can be used with these controllers?

What types of inputs can be used with these controllers?

E5CN

SUB1 SUB1 SUB2

Warranty, Limitations of Liability

Indicates a potentially hazardous situation which, if not

Do not touch the terminals while power is being supplied.

Do not allow pieces of metal, wire clippings, or fine metallic shav-

Do not use the product where subject to flammable or explosive

Never disassemble, modify, or repair the product or touch any of

CAUTION - Risk of Fire and Electric Shock

A malfunction in the Temperature Controller may occasionally

A semiconductor is used in the output section of long-life relays. If

When inserting the body of the Temperature Controller into the

Ensuring Measurement Accuracy

Recommended Ferrite Core

Analog input TC/Pt universal input

TC/Pt universal input Analog input

ALM indicator was changed to SUB indicator.

Display Segments Display Segments

* A 2-level display is set when shipped from the factory.

Previous models Upgraded models

(OUT1) control output 2,

Models with Screwless Clamp Terminal Blocks

Models with Screwless Clamp Terminal Blocks

Models with Screwless Clamp Terminal Blocks

Models with Screwless Clamp Terminal Blocks

Terminals Screws Tightening

Terminals 1 to 6 M2.6 0.23 to 0.25 Nm

Removing the Terminal Block

Note The method for removing the terminal

--- PV/SP display selection for three-level dis-

* A 2-level display is set when shipped from the factory.

Mounting Bracket for upgraded models

OMRON Corporation MADE IN CHINA OMRON

Front Panel Labels

The design has been changed.

Top of Controller Bottom of Controller

Note: (1) Excluding the E5GN.

Operations for Applications

1-1 Names of Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

1-1 Names of Parts

Mode Key Down Key

OUT1 STOP MV No. 3 display

E5AN Down Key

Level Key Mode Key

Level Key PF Function Key/

Mode Key Down Key Up Key

1-1-2 Explanation of Indicators

1-1-3 Using the Keys

1-2 I/O Configuration and Main Functions

HS alarm Auxiliary output 1

Control Control output

Model Number Structure

1. Control Output 1 1. Applicable Controller

Temperature input Control Control output

Alarm 3 Alarm output 3