Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                

Magelis HMI STU 655/855: User Manual

Download as pdf or txt
Download as pdf or txt
You are on page 1of 96

Magelis HMI STU 655/855

EIO0000000614 09/2012

Magelis HMI STU 655/855


User Manual
09/2012
EIO0000000614.03

www.schneider-electric.com
The information provided in this documentation contains general descriptions and/or
technical characteristics of the performance of the products contained herein. This
documentation is not intended as a substitute for and is not to be used for
determining suitability or reliability of these products for specific user applications. It
is the duty of any such user or integrator to perform the appropriate and complete
risk analysis, evaluation and testing of the products with respect to the relevant
specific application or use thereof. Neither Schneider Electric nor any of its affiliates
or subsidiaries shall be responsible or liable for misuse of the information that is
contained herein. If you have any suggestions for improvements or amendments or
have found errors in this publication, please notify us.
No part of this document may be reproduced in any form or by any means, electronic
or mechanical, including photocopying, without express written permission of
Schneider Electric.
All pertinent state, regional, and local safety regulations must be observed when
installing and using this product. For reasons of safety and to help ensure
compliance with documented system data, only the manufacturer should perform
repairs to components.
When devices are used for applications with technical safety requirements, the
relevant instructions must be followed.
Failure to use Schneider Electric software or approved software with our hardware
products may result in injury, harm, or improper operating results.
Failure to observe this information can result in injury or equipment damage.
© 2012 Schneider Electric. All rights reserved.

2 EIO0000000614 09/2012
Table of Contents

Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
About the Book . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Part I HMI STU 655/855 Panels . . . . . . . . . . . . . . . . . . . . . . 9
Chapter 1 HMI STU 655/855 Panels . . . . . . . . . . . . . . . . . . . . . . . . . 11
HMI STU 655/855 Series of Panels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
HMI STU 655/855 Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Parts Identification and Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Certifications and Standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
System Design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Chapter 2 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
2.1 General Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
General Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
2.2 Functional Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Memory, Clock, and Touch Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
2.3 Interface Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Interface Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Specifications of Serial Interface COM1 . . . . . . . . . . . . . . . . . . . . . . . . . . 38
2.4 Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
HMI STU 655/855 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Chapter 3 Installation and Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
3.1 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Panel Cut-out Dimensions and Installation . . . . . . . . . . . . . . . . . . . . . . . . 47
Installation Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
3.2 Wiring Principles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Connecting the Power Cord . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Connecting the Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Grounding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

EIO0000000614 09/2012 3
3.3 USB Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Important Considerations When Using the USB Port . . . . . . . . . . . . . . . 64
USB Data Transfer Cable (BMX XCA USB H018) - USB Driver
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
USB Standard A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
USB Mini-B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
3.4 Ethernet Cable Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Presentation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Part II Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Chapter 4 Configuring the Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Types of Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
System Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Offline Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Diagnostics Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Chapter 5 Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Troubleshooting Checklists . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
Self Test List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Chapter 6 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
Regular Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
Periodic Check Points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95

4 EIO0000000614 09/2012
Safety Information
§

Important Information

NOTICE
Read these instructions carefully, and look at the equipment to become familiar with
the device before trying to install, operate, or maintain it. The following special
messages may appear throughout this documentation or on the equipment to warn
of potential hazards or to call attention to information that clarifies or simplifies a
procedure.

EIO0000000614 09/2012 5
PLEASE NOTE
Electrical equipment should be installed, operated, serviced, and maintained only by
qualified personnel. No responsibility is assumed by Schneider Electric for any
consequences arising out of the use of this material.
A qualified person is one who has skills and knowledge related to the construction
and operation of electrical equipment and its installation, and has received safety
training to recognize and avoid the hazards involved.

6 EIO0000000614 09/2012
About the Book

At a Glance

Document Scope
This manual describes how to use the Magelis HMI STU 655/855 unit.

Validity Note
This documentation is valid for the HMI STU 655/855 when used with Vijeo Designer
version 6.1 SP2 or later.

Product Related Information

WARNING
UNINTENDED EQUIPMENT OPERATION
The application of this product requires expertise in the design and programming
of control systems. Only persons with such expertise should be allowed to
program, install, alter, and apply this product.
Follow all local and national safety codes and standards.
Failure to follow these instructions can result in death, serious injury, or
equipment damage.

User Comments
We welcome your comments about this document. You can reach us by e-mail at
techcomm@schneider-electric.com.

EIO0000000614 09/2012 7
8 EIO0000000614 09/2012
Magelis HMI STU 655/855
HMI STU 655/855
EIO0000000614 09/2012

HMI STU 655/855 Panels

I
Overview
This part describes how to use HMI STU 655/855 Panels.

What Is in This Part?


This part contains the following chapters:
Chapter Chapter Name Page
1 HMI STU 655/855 Panels 11
2 Specifications 29
3 Installation and Wiring 45

EIO0000000614 09/2012 9
HMI STU 655/855

10 EIO0000000614 09/2012
Magelis HMI STU 655/855
HMI STU 655/855
EIO0000000614 09/2012

HMI STU 655/855 Panels

1
Overview
This chapter describes the HMI STU 655/855 Panels and connectable devices.

What Is in This Chapter?


This chapter contains the following topics:
Topic Page
HMI STU 655/855 Series of Panels 12
HMI STU 655/855 Package Contents 15
Accessories 16
Parts Identification and Functions 19
Certifications and Standards 23
System Design 25

EIO0000000614 09/2012 11
HMI STU 655/855

HMI STU 655/855 Series of Panels

Introduction
The HMI STU 655/855 is a Human Machine Interface product that has an operating
voltage of 24 VDC.
The following table describes the HMI STU 655/855 characteristics:

Part number Screen Screen Mono/Color Screen Serial Ethernet


size (pixel) technology port port
resolution
HMI STU 655 8.9 cm 320x240 65 K colors and TFT Yes Yes
(3.5 in.) (QVGA) LED’s backlight
HMI STU 855 14.48 cm 320x240 65 K colors and TFT Yes Yes
(5.7 in.) (QVGA) LED’s backlight
TFT: Thin-Film Transistor Technology.

Critical systems, Detected Alarms and Handling Requirements


Critical detected alarm indicators and system functions require independent and
redundant protection hardware and/or mechanical interlocks.
If the unit for any reason becomes inoperative (for example, an inoperative
backlight) it may be difficult or impossible to identify a function. Functions that may
present a hazard if not immediately executed, such as emergency stop, must be
provided independently of the unit. The design of the control system must take into
account an inoperative unit (backlight) and that the operator is unable to control the
machine or respond to detected errors using the unit.
When the power is cycled, wait at least 10 seconds before restoring the power to the
HMI unit. Switching the power OFF and ON quickly can damage the unit.

12 EIO0000000614 09/2012
HMI STU 655/855

WARNING
LOSS OF CONTROL
z Consider the potential failure modes of control paths in the machine control
system design, such as:
z The possibility of backlight failure,
z Unanticipated link transmission delays or failures,
z The operator being unable to control the machine,
z The operator making errors in the control of the machine.

z Provide a means to achieve a safe state during and after a path failure for critical
control functions such as emergency stop and overtravel stop.
z Provide separate or redundant control paths for critical control functions.
z Test individually and thorougly each implementation of the HMI STU 655/855
for correct operation before service.
Failure to follow these instructions can result in death, serious injury, or
equipment damage.

WARNING
UNINTENDED EQUIPMENT OPERATION
z Do not use the unit as the only means of control for critical system functions
such as motor start/stop or power control.
z Do not use the unit as the only notification device for critical alarms, such as
device overheating or overcurrent.
Failure to follow these instructions can result in death, serious injury, or
equipment damage.

Handling the LCD Panel


The following characteristics are specific to the LCD unit and are considered normal
behavior:
z LCD screen may show unevenness in the brightness of certain images or may
appear different when seen from outside the specified viewing angle. Extended
shadows, or cross-talk, may also appear on the sides of screen images.
z LCD screen pixels may contain black and white colored spots and color display
may seem to have changed over time.
z When the same image is displayed on the screen for a long period, an after-
image may appear when the image is changed. If this happens, turn off the unit,
wait 10 seconds and then restart it.
NOTE: Do not display the same image for a long time, change the screen image
periodically.

EIO0000000614 09/2012 13
HMI STU 655/855

CAUTION
SERIOUS EYE AND SKIN INJURY
The liquid present in the LCD panel contains an irritant:
z Avoid direct skin contact with the liquid.
z Wear gloves when you handle a broken or leaking unit.
z Do not use sharp objects or tools in the vicinity of the LCD touch panel.
z Handle the LCD panel carefully to prevent puncture, bursting, or cracking of the
panel material.
If the panel is damaged and any liquid comes in contact with your skin, immediately
rinse the area with running water for at least 15 min.
If the liquid gets in your eyes, immediately rinse your eyes with running water for
at least 15 minutes and consult a doctor.
Failure to follow these instructions can result in injury or equipment damage.

Using Touch Panel Correctly

WARNING
UNINTENDED EQUIPMENT OPERATION
z Operate the HMI STU 655/855 touch panel with only one finger.
z Do not activate two or more points of the touch panel simultaneously.
Failure to follow these instructions can result in death, serious injury, or
equipment damage.

Use only one finger to select an object on the touch panel.


If the touch panel receives pressure at two or more points at the same time, an
unintended object could be selected.

14 EIO0000000614 09/2012
HMI STU 655/855

HMI STU 655/855 Package Contents

Package Contents
Verify all items listed here are present in your package:
1 2 3

4 5 6 7

Instruction
Sheet

1 Display Module
2 Rear Module
3 Tightening Wrench
4 USB Standard Type A Cable Holder
5 Anti-rotation Tee
6 Terminal Block
7 Quick Reference Guide

Revision
You can identify the product version (PV), revision level (RL) and the software
version (SV) from the unit product label.

EIO0000000614 09/2012 15
HMI STU 655/855

Accessories

Optional Accessories

Product Number Description


HMI ZS61 Set of 5 Screen Protective Sheets
HMI ZSU62 Set of 5 Screen Protective Sheets for HMI STU 855
HMI ZSU KIT Accessory Kit for HMI STU 655/855, contains:
z USB standard Type A cable holder
z USB mini B cable holder
z Anti-rotation Tee
z 2 Panel adaptors
ZB5AZ905 Tightening Wrench
ZB5AZ901 Kit of 10 display module fixing nuts
BMX XCA USB H018 Mini-B USB <-> PC download cable
HMI ZSUSBB USB Front Cable (MiniB)
HMI ZURS USB-232C Converter Cable
XBT ZGPWS1 Set of 5 Power Connectors
HMI S65 Front module 8.9 cm (3.5 in.)
HMI S85 Front module 14.48 cm (5.7 in.)
HMI S5T Rear module

NOTE: Only HMI S5T supports both front module sizes without any new
configuration.

Rear Module Label Front Module Compatibility


HMI S65 HMI S85
HMI STU655 OK –
HMI STU855 – OK
HMI S5T OK OK

DANGER
RISK OF EXPLOSION IN HAZARDOUS LOCATIONS
Do not substitute a rear module labeled HMI STU655 by a rear module labeled
HMI S5T when installed in hazardous locations.
Failure to follow these instructions will result in death or serious injury.

16 EIO0000000614 09/2012
HMI STU 655/855

Serial Interface Items

Product Number Description


XBT Z9780 (2.5 m/8.20 ft) Connects COM1 to Premium, Micro or Twido PLC.
XBT Z9782 (10 m/32.80 ft)
XBT Z9980 (2.5 m/8.20 ft) Connects COM1 to Modicon M340
XBT Z9982 (10 m/32.8 ft)
VW3A8306 Connects COM1 to derivation box TSXSCA62
VW3A8306R10 Connects COM1 to ATV Drives, a Hub LU9GC3 or Fieldbus
Taps TWDXCAT3RJ or TWDXCAISO
XBT ZG939 + XBT Z988 Connects COM1 port to Advantys STB
XBT ZG939 Cable adapter COM1, RJ45
XBT Z968 Connects COM1 port with XBTZ adapter to Premium, Micro
XBT Z9680 or Twido PLC
XBT Z9681
XBT Z9710 Connects COM1 port with XBTZ adapter to Quantum PLC
XBT Z9711 Connects COM1 port with XBTZ adapter to Momentum PLC
XBT Z908 Connects COM1 port with XBTZ adapter to derivation box
TSXSCA62
XBT Z938 Connects COM1 port with XBTZ adapter to ATV drives, a
Hub LU9GC3 or Fieldbus Taps TWDXCAT3RJ or
TWDXCAISO
XBT Z918 Connects COM1 port with XBTZ adapter to Premium SCY
XBT Z988 Connects COM1 port with XBTZ adapter to Advantys STB
XBT Z9733 Connects COM1 to Rockwell DF1 Logix PLC
XBT Z9734 Connects COM1 to Rockwell DH485 Logix PLC
XBT Z9743 Connects COM1 to Omron PLC Sysmac Link series
XBT Z9730 Connects COM1 with XBT Z adapter to Rockwell DF1 PLC
XBT Z9731
XBT Z9732 Connects COM1 with XBT Z adapter to Rockwell DH485
PLC
XBT Z9740 Connects COM1 with XBT Z adapter to Omron PLC Sysmac
Link series

EIO0000000614 09/2012 17
HMI STU 655/855

USB Interface Items

Product Number Description


XBT ZG935 Connects the panel to a personal computer to
transfer screen data and user program
XBT ZGUSB Extends a USB host interface on a
waterproofing cabinet
BMX XCAUSB018 Connects the panel to a:
z personal computer to transfer screen
data and user program
z USB terminal port of a PLC (Modicon
M340)
HMI ZSUSBB Extends a USB device interface on a
waterproofing cabinet
HMI ZURS Connects the panel to a serial printer

Software

Product name Description


Vijeo Designer (Version 5.1 or later for Software installed on a PC for creating HMI
HMI STU 655) unit project data
Vijeo Designer (Version 5.1 SP2 or later for Software installed on a PC for creating HMI
HMI STU 855) unit project data

18 EIO0000000614 09/2012
HMI STU 655/855

Parts Identification and Functions

Display Module
Front:

A, B
A Display: displays user created screens and remote equipment variables.
B Touch panel: performs screen change operations and sends data to the host (PLC).
Rear:

EIO0000000614 09/2012 19
HMI STU 655/855

Rear Module
Front:

Rear:

20 EIO0000000614 09/2012
HMI STU 655/855

Connectors:
Bottom:

C D E F
C Standard A USB port connector: connects the data transfer cable or memory stick to the
unit.
D Serial I/F (host I/F 8 pin RJ45): connects a RS-232C or RS-485 (serial) cable (from the
host/PLC) to the unit (Y port).
E Ethernet Interface (LAN): connects an Ethernet cable (from the host/PLC) to the unit
(X port).
F Power input Terminal block: connects the power input and ground wires to the unit.

EIO0000000614 09/2012 21
HMI STU 655/855

Side:

G
G Mini-B USB port connector: connects the data transfer PC cable to the unit.

22 EIO0000000614 09/2012
HMI STU 655/855

Certifications and Standards

Introduction
Schneider Electric submitted this product for independent testing and
qualification by third-party listing agencies. These agencies have certified this
product as meeting the following standards.

Agency Certifications for HMI STU 655/855 Unit


HMI STU 655/855 unit is certified by the Underwriters Laboratory according to:
z UL 508 and CSA C22.2 n° 142 for Industrial Control Equipment
z UL1604, ANSI/ISA 12.12.01 and CSA C22.2 n° 213 for Electrical Equipment for
Use in Class I, Division 2 Hazardous Locations
ATEX certification by INERIS is ongoing, please refer to product label.
HMI STU 655/855 unit is designed to comply to merchant navy bridge and deck
requirements (Refer to the Schneider Electric website for installation guidelines).
For detailed information, contact your local distributor or see the catalog & marking
on the product.

Hazardous Substances
HMI STU 655/855 unit is designed for compliance with:
z WEEE, Directive 2002/96/EC
z RoHS, Directive 2002/95/EC
z RoHS China, Standard SJ/T 11363-2006

UL Conditions of Acceptability and Handling Cautions for HMI STU 655/855 Unit
The HMI STU 655/855 unit is suitable for use in hazardous locations in accordance
with Class 1, Division 2 standards. All relevant local, state, and regional codes must
be followed.

CE Markings
This product conforms to the necessary requirements of the following Directives for
applying the CE label:
z 2006/95/EC Low Voltage Directive
z 2004/108/EC EMC Directive

This conformity is based on compliance with IEC61131-2.

EIO0000000614 09/2012 23
HMI STU 655/855

WARNING
RISK OF EXPLOSION IN HAZARDOUS LOCATIONS
z Verify that the power, input and output (I/O) wiring are in accordance with Class
I, Division 2 wiring methods.
z Do not substitute components that may impair compliance to Class I, Division 2.
z Do not connect or disconnect equipment unless power has been switched off or
the area is known to be non-hazardous.
z Securely lock externally connected units and each interface before turning on
the power supply.
Failure to follow these instructions can result in death, serious injury, or
equipment damage.

Interfaces are: COM1, ETHERNET, USB1 and USB2.

WARNING
RISK OF EXPLOSION IN HAZARDOUS LOCATIONS
z Do not disconnect while circuit is live.
z Potential electrostatic charging hazard: wipe the front panel of the terminal with
a damp cloth before turning ON.
Failure to follow these instructions can result in death, serious injury, or
equipment damage.

24 EIO0000000614 09/2012
HMI STU 655/855

System Design

Introduction
The following diagrams represent equipment that can be connected to the unit.

HMI STU 655/855 Edit Mode Peripherals

1 2

Vijeo
Designer

3
1 HMI STU 655/855 unit
2 Personal computer
3 BMX XCA USB H018 cable
4 To Ethernet network

EIO0000000614 09/2012 25
HMI STU 655/855

HMI STU 655/855 Run Mode Peripherals

3
1 HMI STU 655/855 unit
2 PLC
3 HMI ZSUSBB cable
4 To Ethernet network

26 EIO0000000614 09/2012
HMI STU 655/855

Connecting Magelis HMI STU 655/855 unit to an external device


The following diagram represents a selection of equipment that can be connected to
the HMI STU 655/855 unit.

1 HMI STU 655/855


2 USB HOST interface (TYPE-A)
3 USB Front Cable (A) 1 m (3.28 ft) XBT ZGUSB
4 USB Memory
5 USB HUB (Self Power Only)
6 Barcode Reader
7 Printer
8 USB-232C Converter Cable 0.5 m (1.64 ft) HMI ZURS
9 Printer (Commodity). NEC PC-PR201/PL Command Compatible, EPSON ESC/P24-J84©
Command Compatible or HP Laser Jet PCL4 Command Compatible
10 USB DEVICE interface (TYPE-miniB)
11 Download Cable BMX XCA USB H018
12 PC
13 Vijeo-Designer
14 USB Front Cable HMI ZSUSBB

EIO0000000614 09/2012 27
HMI STU 655/855

28 EIO0000000614 09/2012
Magelis HMI STU 655/855

EIO0000000614 09/2012

Specifications

2
Overview
This chapter presents the HMI STU 655/855 specifications.

What Is in This Chapter?


This chapter contains the following sections:
Section Topic Page
2.1 General Specifications 30
2.2 Functional Specifications 32
2.3 Interface Specifications 36
2.4 Dimensions 40

EIO0000000614 09/2012 29
2.1 General Specifications

General Specifications

Electrical Specifications
The following table shows the electrical specifications of HMI STU 655/855:

Part Number Rated Input Acceptable Power In-Rush Voltage Insulation


Input Voltage Voltage Consumption Current endurance Resistance
Voltage Limits Drop between between power
power terminal terminal and
and frame FG
ground (FG)
HMI STU 655 24 Vdc 20.4 Vdc to ≤10 ms ≤6.5 W ≤30 A 1000 Vac 10 MΩ or higher
28.8 Vdc 20 mA for 1 at 500 Vdc
minute
HMI STU 855 24 Vdc 20.4 Vdc to ≤7 ms ≤6.8 W ≤30 A 1000 Vac 10 MΩ or higher
28.8 Vdc 20 mA for 1 at 500 Vdc
minute

Environmental Specifications
The following table shows the environmental specifications of HMI STU 655/855:

Specification HMI STU 655 HMI STU 855


Ambient operating 0 ° C to +50 ° C (32 ° F to 122 ° F) 0 ° C to +50 ° C (32 ° F to 122 ° F)
temperature (cabinet
interior and panel face)
Storage temperature -20 ° C to +60 ° C (-4 ° F to 140 ° F) -20 ° C to +60 ° C (-4 ° F to 140 ° F)
Relative Humidity 85 % w/o condensation (Non- 85 % w/o condensation (Non-condensing,
condensing, wet bulb temperature 39 ° C wet bulb temperature 39 ° C (102.2 ° F) or
Physical Environment

(102.2 ° F) or less) less)


Air purity (dust) ≤0.1 mg/m3 (10-7 oz/ft3) (non- ≤0.1 mg/m3 (10-7 oz/ft3) (non-conductive
conductive levels) levels)
Corrosive gases Free of corrosive gases Free of corrosive gases
Atmospheric pressure 800 hPa to 1,114 hPa (2000 m 800 hPa to 1,114 hPa (2000 m (6,561 ft)
(6,561 ft) or lower) or lower)

30 EIO0000000614 09/2012
Specification HMI STU 655 HMI STU 855
Vibration immunity IEC 61131-2 IEC 61131-2
(operating) 1gn 5Hz to 150Hz (maximum 3.5 mm 1gn 5Hz to 150Hz (maximum 3.5 mm
(0.13 in.)) (0.13 in.))
Protection (front panel) IP 65 - (IEC 60529) IP 65 - (IEC 60529)
Protection structure Type 4X indoor, installed on a panel Type 4X indoor, installed on a panel
Mechanical Environment

Protection (rear panel) IP 20 - (IEC 60529) IP 20 - (IEC 60529)


Shock immunity IEC 61131-2 IEC 61131-2
(operating) 15gn 11 ms 15gn 11 ms
Cooling method Natural air circulation Natural air circulation
Weight 0.25 kg (0.55 lb.) or less (main unit only) 0.25 kg (0.55 lb.) or less (main unit only)
Color Front bezel: dark gray Front bezel: dark gray
Material PC/PBT PC/PBT & PAA
Noise immunity Noise voltage: 1000 Vp-p Noise voltage: 1000 Vp-p
Pulse width: 1 µs Pulse width: 1 µs
Rising time: 1 ns Rising time: 1 ns
High Energy Surges 1 kV CM, 0.5 kV DM on DC power 1 kV CM, 0.5 kV DM on DC power supply
supply 1 kV CM on shielded cables
1 kV CM on shielded cables
Electrical fast transient 2 kV CM, 2 kV DM on DC power supply. 2 kV CM, 2 kV DM on DC power supply.
Electrical Environment

burst 1 kV on shielded cables 1 kV on shielded cables


Radiated radio frequency 10 V/m / 80 MHz to 2.7GHz 10 V/m / 80 MHz to 2.7GHz
electromagnetic field Sinus amplitude modulated 80 % Sinus amplitude modulated 80 %
1 kHz + Internal clock frequency 1 kHz + Internal clock frequency
Electrostatic Discharge 6 kV direct contact 6 kV direct contact
Immunity 8 kV air contact 8 kV air contact
Grounding D type grounding (SG-FG connected) D type grounding (SG-FG connected)
CM Common Mode
DM Differential Mode

EIO0000000614 09/2012 31
2.2 Functional Specifications

Overview
This section presents the HMI STU 655/855 functional specifications of the display,
memory and interfaces.

What Is in This Section?


This section contains the following topics:
Topic Page
Display 33
Memory, Clock, and Touch Panel 35

32 EIO0000000614 09/2012
Display

Display Specifications
The following table shows the display specifications of the HMI STU 655/855:

Items HMI STU 655 HMI STU 855


Type Color TFT LCD Color TFT LCD
Resolution 320 x 240 320 x 240
(pixels) (QVGA) (QVGA)
Active Display 70.56 x 52.92 mm 115.2 x 86.4 mm
Area (W x H) (2.78 x 2.08 in.) (4.53 x 3.40 in.)
Colors 65536 colors 65536 colors
Backlight LED backlight: LED backlight:
Lifetime: 50000 hours before dimmed to 50% Lifetime: 50000 hours before dimmed to 50%
brightness. Ambient temperature = 25° C (77° F) brightness. Ambient temperature = 25° C (77° F)
Non exchangeable Non exchangeable
LED ON / OFF control, adjustable screen saver LED ON / OFF control, adjustable screen saver
activation time activation time
Brightness 16 levels of adjustment available via touch panel 16 levels of adjustment available via touch panel
adjustment in the Configuration menu. in the Configuration menu.
Brightness on White LED: 350 cd/m2 (33 cd/ft2) maximum White LED: 350 cd/m2 (33 cd/ft2) maximum
LCD surface
View angle z 60 degrees: left, right z 80 degrees: left, right
z 40 degrees: up z 70 degrees: up
z 60 degrees: down z 70 degrees: down

(Test condition: contrast ratio > 2) (Test condition: contrast ratio > 2)
System ASCII: (Code page 850) alphanumeric ASCII: (Code page 850) alphanumeric (including
embedded (including european characters) european characters)
language Chinese: (GB2312-80 codes) simplified Chinese Chinese: (GB2312-80 codes) simplified Chinese
character sets fonts fonts
Japanese: ANK 158 Japanese: ANK 158
Kanji: 6,962 (JIS Standards 1 & 2) (including 607 Kanji: 6,962 (JIS Standards 1 & 2) (including 607
non-kanji characters) non-kanji characters)
Korean: (KSC5601 - 1992 codes) Hangul fonts Korean: (KSC5601 - 1992 codes) Hangul fonts
Taiwanese: (Big 5 codes) traditional Chinese Taiwanese: (Big 5 codes) traditional Chinese
fonts fonts
Character sizes 8 x 8, 8 x 16, 16 x 16 and 32 x 32 pixels fonts 8 x 8, 8 x 16, 16 x 16 and 32 x 32 pixels fonts
(2)

EIO0000000614 09/2012 33
Items HMI STU 655 HMI STU 855
Font sizes Width can be expanded 1 to 8 times. Height can Width can be expanded 1 to 8 times. Height can
be expanded 1/2 and 1 to 8 times. be expanded 1/2 and 1 to 8 times.
8 x 8 pixels 40 characters per row x 30 rows 40 characters per row x 30 rows
8 x 16 pixels 40 character per row x 15 rows 40 character per row x 15 rows
16 x 16 pixels 20 character per row x 15 rows 20 character per row x 15 rows
32 x 32 pixels 10 character per row x 7 rows 10 character per row x 7 rows

34 EIO0000000614 09/2012
Memory, Clock, and Touch Panel

Memory
The following table shows the memory specifications of HMI STU 655/855:

Items Specification
Application flash 32 MB
Data backup in FRAM 64 KB
Application run DRAM 64 MB

Memory Back-up Management in FRAM


Detected alarms data are saved:
z automatically every hour in the back-up memory.
z upon user request through Vijeo Designer application design.

Clock
Variations in operating conditions can cause a clock shift from -380 to +90 seconds
per month.

Touch Panel
The following table shows the touch panel specifications of HMI STU 655/855:

Items Specification
Type Analog resistance film type (Metal Tab, Golden
Plated)
Lifetime 1 million touches or more

EIO0000000614 09/2012 35
2.3 Interface Specifications

Overview
This section presents the interface specifications of the HMI STU 655/855 units.

What Is in This Section?


This section contains the following topics:
Topic Page
Interface Specifications 37
Specifications of Serial Interface COM1 38

36 EIO0000000614 09/2012
Interface Specifications

Serial Interface COM1


The following table describes the serial interface COM1 of HMI STU 655/855 unit:

Interface Description
Serial interface COM1 RJ45
Asynchronous Transmission RS-232C / RS-485
Data Length 7 or 8 bits
Stop Bit 1 or 2 bits
Parity None, odd or even
Data Transmission Speed 2,400 to 115,200 bps
Maximum Transmission Distance RS-232C 15 m (49.21 ft)/ RS-485 1200 m (3,937 ft) at
100 kbps

USB1 Interface (USB peripherals)


The following table describes the USB1 Interface of HMI STU 655/855 unit:

Interface Description
HOST Interface
Transmission Speed High speed 480 Mbps
Full speed 12 Mbps
Low speed 1.5 Mbps
Maximum Current Supplied 250 mA
Maximum Transmission Distance 5 m (16.40 ft) at 12 Mbps
Connector USB Type-A V2.0

USB2 Interface (application download)


USB Mini B V2.0 type connector is used for application download.

Ethernet Interface
The following table describes the LED colors and status:

LED Contents
Green 1 Link state
Green 2 Activity

EIO0000000614 09/2012 37
Specifications of Serial Interface COM1

Introduction
This interface is used to connect the HMI STU 655/855 to remote equipment via an
RS-232C or RS-485 cable. The connector used is a RJ45-8 pin type connector.
When using a long PLC cable to connect the unit, a difference of electric potential
can be observed between the cable and the unit, even if both are connected to
ground.
The serial port is not isolated. The SG (signal ground) and the FG (frame ground)
terminals are connected inside the unit.
NOTE: When setting up RS-485 communication, the cable diagram for some
equipement may require polarization on the terminal side. This terminal does not
require any special setting as it handles polarization automatically.

DANGER
ELECTRIC SHOCK
When using the SG terminal to connect an external device to the unit:
z Verify that a short-circuit loop is not created when you set up the system.
z Connect the #8 SG terminal to remote equipment when the host (PLC) unit is
not isolated. Connect the #8 SG terminal to a known reliable ground connection
to reduce the risk of damaging the RS-232C/RS-485 circuit.
Failure to follow these instructions will result in death or serious injury.

Serial Interface COM1


The following table describes the RJ45-8 pin connector on the HMI STU 655/855
units:

Pin Connection Pin Signal Name Direction Meaning


1 RXD Input Receive Data (RS-232C)
Front
2 TXD Output Send Data (RS-232C)
3 Not connected - -
4 D1 Output/Input Transfer Data (RS-485)
5 D0 Output/Input Transfer Data (RS-485)
6 RTS Output Request To Send
7 Not connected - -
8 SG - Signal Ground

38 EIO0000000614 09/2012
RS-232C Type
The following table describes the 9-pin COM interface connector on the
HMI STU 655/855:

RS-232C
Label Signal Name Direction Meaning
CI CI(RI) Input Called status display
CD CD Input Carrier detect
CS CS(CTS) Input Send possible
RS RS(RTC) Output Request to send
SG SG - Signal ground
DR DR(DSR) Input Data set ready
ER ER(DTR) Output Data terminal ready
RD RD(RXD) Input Receive data
SD SD(TXD) Output Send data

Any excessive weight or stress on communication cables may cause a


disconnection and unintended equipment operation.

CAUTION
LOSS OF COMMUNICATION
When using HMI STU 655/855:
z All connections to the communication ports on the bottom and sides of the unit
must not put excessive stress on the ports.
z Securely attach communication cables to the panel or cabinet.
z Use only RJ45 cables with a locking tab in good condition.

Failure to follow these instructions can result in injury or equipment damage.

EIO0000000614 09/2012 39
2.4 Dimensions

HMI STU 655/855

Display Module HMI STU 655


mm
in.

15.3 16.2
0.60 0.63
Ø 0.86

2.16
Ø 22

55
(2)
(1)

72.6
2.85
31.5 97.6
1.24 3.84

Ø 3.43 30
Ø 0.13 1.18
0.26
6.7

(3)

(1) Front
(2) Right Side
(2) Top

40 EIO0000000614 09/2012
Display Module HMI STU 855

(3)

mm 163
in. 6.41

117.7 15.3
4.63 0.60

Ø22.1
Ø0.87
129.4
88.4
3.48

5.09
(2)

(1) (5)

17.5
0.69

32.8
1.29 (4)
(1) Front
(2) Right Side
(3) Bottom
(4) Top
(5) Left Side

EIO0000000614 09/2012 41
Rear Module HMI STU 655/855

mm 30.6
in. 1.20

9.5
0.37
17.2

98.1
3.86
0.67

40.1 118
1.57 4.64

(2) (1)
(1) Front
(2) Right Side

42 EIO0000000614 09/2012
Display and Rear Modules HMI STU 655

mm
in.

98.15
3.14

3.62

3.86
80

92
16.2 30.6 97.6
0.63 1.20 3.84
56.3 118
2.21 4.64

(2) (1)
(1) Right Side
(2) Front

EIO0000000614 09/2012 43
Display and Rear Modules HMI STU 855

(4)
mm
in.

118
4.64

5.094
129.4

3.62
(1)

92

17.5 30.6 163 (5)


1.20 6.41
0.69
56.5
2.224
(2)

(3)
(1) Front
(2) Right side
(3) Top
(4) Bottom
(5) Left side

44 EIO0000000614 09/2012
Magelis HMI STU 655/855

EIO0000000614 09/2012

Installation and Wiring

3
Overview
This chapter describes the installation procedures and the wiring principles for
HMI STU 655/855.

What Is in This Chapter?


This chapter contains the following sections:
Section Topic Page
3.1 Installation 46
3.2 Wiring Principles 55
3.3 USB Port 63
3.4 Ethernet Cable Connector 72

EIO0000000614 09/2012 45
3.1 Installation

Overview
This section describes the installation Procedures for HMI STU 655/855.

What Is in This Section?


This section contains the following topics:
Topic Page
Panel Cut-out Dimensions and Installation 47
Installation Procedures 51

46 EIO0000000614 09/2012
Panel Cut-out Dimensions and Installation

Inserting a HMI STU 655/855 Without an Anti-rotation Tee


Create a panel cut-out and insert the display module of the unit into the panel from
the front. The following illustration shows the panel cut-out for a HMI STU 655/855
unit without a tee:

Dimensions

Unit A (mm) A (in.) B (1) B (2)


HMI STU 655/855 +0 +0
22.50 0.88 1.5...6 mm ( 3...6 mm
-0.30 -0.01 0.06...0.23 in.) (0.11...0.23 in.)

(1) Steel sheet


(2) Glass fiber reinforced plastics (minimum GF30)

NOTE: Without the tee option, the rotating torque that can be supported by the
display module is 2.5 Nm (22.12 in-lb).

EIO0000000614 09/2012 47
Inserting a HMI STU 655/855 With an Anti-rotation Tee
Create a panel cut-out and insert the display module of the unit into the panel from
the front. The following illustration shows the panel cut-out for a HMI STU 655/855
unit using a tee:

Dimensions

Unit C (mm) C (in.) D (mm) D (in.)


HMI STU 655/855 +0 +0 +0 +0
30.00 1.18 4.00 0.15
-0.20 -0.007 -0.20 -0.007

NOTE: With the tee option, the rotating torque that can be supported by the display
module is 6 Nm (53.10 in-lb).

48 EIO0000000614 09/2012
Illustration

(1) (2)

(4)

(3)

(1) Display module


(2) Support
(3) Nut
(4) Tee

EIO0000000614 09/2012 49
Panel Adaptor
The Panel Adaptor, supplied in the accessory kit HMI ZSU KIT (see page 16),
allows mounting the product on a:
z Metallic support with a thickness between 1 and 1.5 mm (0.039 and 0.059 in.)
z Plastic support with a thickness between 1 and 3 mm (0.039 and 0.118 in.) for
HMI STU 655
z Glass fiber reinforced plastic with a thickness between 2 and 3 mm (0.078 and
0.118 in.) for HMI STU 855
The following illustration shows the assembly with the panel adaptor:
(1) (2)

(3)

(5)

(4)

(1) Display module


(2) Support
(3) Panel adaptor
(4) Nut
(5) Tee

50 EIO0000000614 09/2012
Installation Procedures

Panel Setup Procedure


Mount the unit in an enclosure that provides a clean, dry, robust and controlled
environment (IP65 enclosure or UL50 4x, if indoors.) (see page 30)
Before installing the HMI STU 655/855 verify that:
z The gasket is flat and not damaged.
z The installation panel or cabinet surface is flat (planarity tolerance: 0.5 mm
(0.019 in.)), in good condition and has no jagged edges. Metal reinforcing strips
may be attached to the inside of the panel, near the panel cut-out, to increase the
rigidity.
z The panel must be designed to avoid any induced vibration resonance on the rear
module exceeding a punctual factor of 10 and to avoid any induced permanent
vibration resonance.
To reduce the resonance use the panel adaptor accessory.
z The ambient operating temperature and the ambient humidity are within their
specified ranges (see page 30).
z The heat from surrounding equipment does not cause the unit to exceed its
specified operating temperature (see page 30).
z The panel face is not inclined more than 30° when installing the unit in a slanted
panel:

30 or less

EIO0000000614 09/2012 51
z the power plug is positioned vertically when the unit is vertically installed.
z the unit is at least 100 mm (3.94 in.) away from adjacent structures and other
equipment for easier maintenance, operation and improved ventilation:
mm
in.

3.94
3.94

100
100

100 100 100


3.94 3.94 39.4

3.94
3.94
100

100

Step Action
1 Place the unit on a clean and level surface with the display panel facing
downward.
2 The support thickness depends on the material:
z Metallic: between 1.5 and 6 mm (0.059 and 0.236 in.)
z Plastic: between 3 and 6 mm (0.118 and 0.236 in.)

If the thickness is between 1 and 1.5 mm (0.039 and 0.059 in.) for metallic
support or 1 and 3 mm (0.039 and 0.118 in.) for plastic, use the panel adaptor
supplied in accessory kit HMI ZSU KIT (see page 16).
3 Create the correct sized holes required to install the unit, using the Panel Cut-
out Dimension and Installation (see page 47).

52 EIO0000000614 09/2012
Step Action
4 Insert the display module (with Tee, if used) into the panel hole:

Screw the nut with the tightening wrench with a torque between 1.2 and 2 Nm
(10.62 and 17.70 in-lb.).

EIO0000000614 09/2012 53
Step Action
5 Insert and push the rear module until it locks into place:

Click

Insert and
push

Free Locked

6 To remove the rear module, push the yellow button to unlock it, then pull the
rear module out:
Push

Pull

Locked Unlocked Free

54 EIO0000000614 09/2012
3.2 Wiring Principles

Overview
This section presents HMI STU 655/855 wiring principles.

What Is in This Section?


This section contains the following topics:
Topic Page
Connecting the Power Cord 56
Connecting the Power Supply 59
Grounding 61

EIO0000000614 09/2012 55
Connecting the Power Cord

Introduction
Follow these instructions when supplying power to the unit:
z When the frame ground (FG) terminal is connected, verify the wire is grounded.
Not grounding the unit can result in excessive Electromagnetic Interference
(EMI). Grounding is required to meet EMC level immunity.
z The shield ground (SG) and FG terminals are connected internally in the unit.
z Remove power before wiring to the power terminals of the unit.
z The unit uses only 24 Vdc power. Using any other level of power can damage
both the power supply and the unit.
z Since the unit is not equipped with a power switch, connect a power switch to the
unit’s power supply.

Power Cord Preparation


Before using your power cord:
z Verify the ground wire is the same gauge or heavier than the power wires.
z Do not use aluminum wires for the power cord for power supply.
z If the conductor end (individual) wires are not twisted correctly, the end wires may
either short loop to each other or against an electrode. To avoid this, use
D25CE/AZ5CE cable ends.
2
z Use wires that are 0.2 to 2.5 mm (24 - 12 AWG) for the power cord, and twist the
wire ends before attaching the terminals.
z The conductor type is solid or stranded wire.
z To reduce electromagnetic noise, make the power cord as short as possible.

Power Plug Illustration

+ ,QVHUWLRQ
- 'LUHFWLRQ
FG

Connection Wire
+ 24 V
- 0V
FG Grounded terminal connected to the unit chassis

56 EIO0000000614 09/2012
How to connect the Power Cord
The following table explains how to connect the power plug:

Step Action
1 Remove the power cord from the power supply.
2 Remove the power plug from the unit.
3 Remove 7 mm (0.28 in.) of the vinyl cover of each of the power cord wires.

4 If using stranded wire, twist the ends. Tinning the ends with solder reduces the
risk of fraying and enhances electrical transfer.
5 Connect the wires to the power plug by using a flat-blade screwdriver (Size
0.6 x 3.5).
6 Torque the mounting screws: 0.5 to 0.6 Nm (4.4 to 5.2 lb-in).
7 Replace the power plug to the power connector.

NOTE:
z Do not solder the wire directly to the power receptable pin.
z The power supply cord must meet the specification shown above. Twist the
power cords together, up to the power plug, for EMC cancellation. (See
illustration as shown below).

EIO0000000614 09/2012 57
Power Connection
The following illustration displays a connection of the power cord:

Terminal block
wire set block

Power Plug
+

FG
-

58 EIO0000000614 09/2012
Connecting the Power Supply

Precautions
z Connect the power cord to the power connector on the side of the unit using the
power plug.
z Use a regulated power supply with a Class 2 power supply between the line and
the ground.
z Do not bundle the power supply cord with, or keep close to, main circuit lines
(high voltage, high current), or input/output signal lines.
z Connect a lightning surge absorber to handle power surges.
Excessive stress on the power connection or attempting to install a unit with the
power cables connected may disconnect or cause damage to the power
connections. This can cause short circuits, fire or unintended equipment operation.

WARNING
SHORT CIRCUITS, FIRE, OR UNINTENDED EQUIPMENT OPERATION
z Securely attach power cables to the panel or cabinet.
z Use the designated torque to tighten the unit terminal block screws.
z Install and fasten unit on installation panel or cabinet prior to connecting Power
Supply and Communication lines.
Failure to follow these instructions can result in death, serious injury, or
equipment damage.

EIO0000000614 09/2012 59
Power Supply Connections
For ease of maintenance, use the following optional connection diagram to set up
your power supply connections.

NOTE:
z Ground the surge absorber (E1) separately from the unit (E2).
z Select a surge absorber that has a maximum circuit voltage greater than the peak
voltage of the power supply.
The following diagram displays a lightning surge absorber connection:

60 EIO0000000614 09/2012
Grounding

Introduction
Take the following precautions for grounding the unit.

Exclusive Grounding
Connect the frame ground (FG) terminal on the power plug to an exclusive ground.

Grounding Procedure

Step Action
1 Check that the grounding resistance is less than 100 Ω.
2 Create the connection point as close to the unit as possible, and make the wire
as short as possible. When using a long grounding wire, replace the thin wire
with a thicker wire, and place it in a duct.

EIO0000000614 09/2012 61
Common Grounding
Precautions:
Electromagnetic Interference (EMI) can be created if the devices are improperly
grounded. Electromagnetic Interference (EMI) can cause loss of communication.
Do not use common grounding, except for the authorized configuration described
below.
If exclusive grounding is not possible, use a common connection point.

62 EIO0000000614 09/2012
3.3 USB Port

Overview
This section presents the USB port.

What Is in This Section?


This section contains the following topics:
Topic Page
Important Considerations When Using the USB Port 64
USB Data Transfer Cable (BMX XCA USB H018) - USB Driver Installation 65
USB Standard A 67
USB Mini-B 70

EIO0000000614 09/2012 63
Important Considerations When Using the USB Port

Introduction
Data transfer cable (BMX XCA USB H018) can be attached to the USB port to allow
data transfer from the computer to the unit.

WARNING
RISK OF EXPLOSION IN HAZARDOUS LOCATIONS
In hazardous locations as described in UL1604 and ANSI/ISA - 12.12.01:
z confirm that the USB cable has been attached with the USB cable clamp before
using the USB host interface.
z remove power before attaching or detaching any connector(s) to or from the
unit.
Failure to follow these instructions can result in death, serious injury, or
equipment damage.

NOTICE
UNINTENTED EQUIPEMENT OPERATION
Do not use the 4.5 m USB cable BMX XCA USB H045.
Failure to follow these instructions can result in equipment damage.

64 EIO0000000614 09/2012
USB Data Transfer Cable (BMX XCA USB H018) - USB Driver Installation

Important information
Follow the procedure described below to avoid damage to the cable connector or
the unit:
z Do not connect the USB data transfer cable until told to do so in the instructions.
z Insert the connector at the correct angle when connecting the USB data transfer
cable to the PC or to the unit.
z Hold the connector, not the cable itself when disconnecting the cable.
z Use the port designated during installation. If the cable is unplugged from the port
designated during installation and connected to a different port, the OS
(Operating System) will not recognize the new port.
z Restart the PC and quit all resident applications before re-installing the software
if the installation does not complete successfully.
NOTE: Vijeo Designer must be installed before installing the USB driver.

Installation Procedure

Step Action
1 Insert the Vijeo Designer Installation CR-ROM into your CR-ROM drive. The
Setup window for Vijeo Designer opens automatically. If not, at the Windows
Start menu, click Run and type x:\install.exe (where x is your CR-ROM drive
name).
2 In the install menu, select USB Driver.
3 Select the driver you want to install from the window that appears. For the
BMX XCA USB H018 USB cable, select Install USB driver for....
4 A popup window appears stating the installation of the driver was successful.
5 Connect the USB cable to the computer. Windows automatically detects the
cable and states that the device is ready to use.

EIO0000000614 09/2012 65
Post-Installation Check
Perform the following check after installation:

Step Action
1 On the target machine, verify the USB cable is physically connected to the USB
port.
2 On the PC, verify the USB cable is physically connected to the USB port.
3 On the desktop, right-click My Computer and click Properties.
4 In System Properties dialog box, select Hardware tab, and then click Device
Manager.
5 In Device Manager, the USB link cable (BMX XCA USB H018) is displayed
below the USB controller.

Troubleshooting

Detected problem/Symptom Solution


The USB cable is not recognized. Connect the cable correctly, or restart your
PC. Also, when connecting a USB hub,
Overcurrent occurred.
connect it directly to your PC USB port.
The Plug and Play is not functioning correctly.
You are unable to use the USB cable after The power supplied from the hub may be
connecting it to a USB hub. insufficient. Verify the hub is self-powered.
Connect the cable directly to the PC USB
port.
After installation, a ? is displayed when you The driver has not been installed correctly.
try to confirm the cable’s status via the Device Uninstall the driver and re-install it.
Manager.

Uninstalling the USB Driver

Step Action
1 Click the USB device icon Stop USB link cable in the Windows task tray and
then click Stop USB link cable (BMX XCA USB H018) for Windows 2000, or
Safely remove USB link cable (BMX XCA USB H018) for Windows XP.
2 When the Safe To Remove Hardware message box appears, remove the USB
download cable.
3 Click OK to close the message box.

66 EIO0000000614 09/2012
USB Standard A

Introduction
When using a USB device, you can attach a USB holder to the USB interface on the
side of the unit to prevent the USB cable from being disconnected.

WARNING
RISK OF EXPLOSION IN HAZARDOUS LOCATIONS
In hazardous locations as described in UL1604 and ANSI/ISA - 12.12.01:
z confirm that the USB cable has been attached with the USB cable clamp before
using the USB host interface.
z remove power before attaching or detaching any connector(s) to or from the
unit.
Failure to follow these instructions can result in death, serious injury, or
equipment damage.

Attaching the USB Holder

Step Action
1 Attach the USB holder to the USB Host Interface on the rear module. Hook the
upper pick of the USB holder to the attachment hole of the main unit, and insert
the lower pick as shown below to fix the USB holder.

(1)

(1) USB Holder

EIO0000000614 09/2012 67
Step Action
2 Insert the USB cable into the USB host interface.

(1)

(2)
(1) USB Holder
(2) USB Cable
3 Attach the USB cover to fix the USB cable in place. Insert the USB cover into
the tab of the USB holder.

(3)

(1)

(2)
(1) USB Holder
(2) USB Cover
(3) USB Cable

68 EIO0000000614 09/2012
Removing the USB Holder
Push down the tab of the USB holder and then remove the USB cover.

(3)

(1)
(2)
(1) USB Holder
(2) USB Cover
(3) USB Cable

EIO0000000614 09/2012 69
USB Mini-B

Introduction
When using a USB device, you can attach a USB holder to the USB interface on the
side of the unit to prevent the USB cable from being disconnected.

WARNING
RISK OF EXPLOSION IN HAZARDOUS LOCATIONS
In hazardous locations as described in UL1604 and ANSI/ISA - 12.12.01:
z confirm that the USB cable has been attached with the USB cable clamp before
using the USB host interface.
z remove power before attaching or detaching any connector(s) to or from the
unit.
Failure to follow these instructions can result in death, serious injury, or
equipment damage.

Attaching the USB Holder

Step Action
1 Insert the USB cable into the USB host interface.

(1)

(1) USB Cable

70 EIO0000000614 09/2012
Step Action
2 Attach the USB holder to fix the USB cable in place.

(1) (2)

(1) USB Holder


(2) USB Cable

Removing the USB Holder


Push down the tab of the USB holder and then remove the USB holder.

2
1

(1) (2)

(1) USB Holder


(2) USB Cable

EIO0000000614 09/2012 71
3.4 Ethernet Cable Connector

Presentation

Introduction
The HMI STU 655/855 comes equipped with an IEEE802.3 compliant Ethernet
interface, that transmits and receives data at 10 Mbps or 100 Mbps.

Ethernet Cable Connector


The following illustration displays the location of the RJ45 Ethernet cable connector:

Do not confuse the RJ45 Ethernet connector with the RJ45 COM1/COM2 serial port.
NOTE: Ethernet networks must be installed by a trained and qualified person.
1:1 connections must be made with a hub or a switch. It is possible to use the 1:1
connection with a cross cable depending on the connected PCs and network cards.

72 EIO0000000614 09/2012
Magelis HMI STU 655/855

EIO0000000614 09/2012

Settings

II
Overview
This part describes the settings available on the target machine as well as how to
debug the unit.

What Is in This Part?


This part contains the following chapters:
Chapter Chapter Name Page
4 Configuring the Unit 75
5 Troubleshooting 85
6 Maintenance 91

EIO0000000614 09/2012 73
74 EIO0000000614 09/2012
Magelis HMI STU 655/855

EIO0000000614 09/2012

Configuring the Unit

4
Overview
This chapter presents the settings on the HMI STU 655/855 units.

What Is in This Chapter?


This chapter contains the following topics:
Topic Page
Types of Settings 76
System Settings 77
Offline Settings 80
Diagnostics Settings 83

EIO0000000614 09/2012 75
Types of Settings

Introduction
You can use the Settings menu to configure the unit.
Depending on how you use your HMI STU 655/855, you can display the Settings
menu using three different methods:
z Use an action,
z Touch the top-left corner of the panel when powering up,
z Touch two corners of the panel successively while the application is running.

You can select which methods your application uses in the Vijeo Designer editor’s
Target properties.

Calling Up the Settings Menu

Step Action
1 Set up any combination of the following methods for displaying the Settings
menu.
z Action: Create a switch and add the Configuration System Operation. See
the Vijeo Designer online help for more information on creating a switch.
z Top-Left Corner: In Target properties, set To Configuration to either Top
Left Corner or Top Left/2 Corner.
z Touch two corners successively: In Target properties, set To
Configuration to either 2 Corner or Top Left/2 Corner.
If you set To Configuration to None and do not create a switch to display the
Settings menu, then there is no way to configure the unit at runtime.
2 Connect the power supply.
3 Depending on what you set up in Step 1, you can display the Configuration
menu using one of the following methods:
z Action: Touch the switch set up with the Configuration system operation.
z Top-Left Corner: Touch the top-left corner of the screen within ten seconds
after the unit begins starting up.
z Touch two corners successively: Touch successively the top left corner
then the bottom right corner within half a second. The touch area is 50 dots
by 50 dots.
Vijeo Designer Runtime restarts and displays the Settings menu.
4 The Settings menu contains 3 tabs: Offline, System, Diagnostics and To
Run Mode. Click a tab to display its settings.

76 EIO0000000614 09/2012
System Settings

Introduction
You can change system settings while the user application is still running.

Stylus
Use the Stylus to calibrate the screen:

Step Action
1 In the Setting menu, press the System tab.
2 Press the Stylus button.
3 Press the center of the cross several times to complete calibration of the
screen.

Changing the Date/Time

Step Action
1 In the Setting menu, press the System tab.
2 Press the Date/Time button.
3 Press any of the Year, Month or Day fields and a data entry keypad is
displayed. Use this keypad to define the selected date setting.
4 Press any of the Hour, Minutes or Seconds fields and a data entry keypad is
displayed. Use this keypad to define the selected time setting.
5 In the Time Zone tab press the up/down arrows to select the desired time
zone.
6 Check the Auto. adjust clock for daylight saving time box to choose
adjusting clock for daylight saving time changes automatically.
7 In the DST tab press the up/down arrows to select the desired daylight saving
time type:
z Date: the DST is added, or subtracted, on the exact date chosen.
z Rule: the DST is added, or subtracted, on a specific weekday in the month.

8 Press the Amount field and a data entry keypad is displayed. Use this keypad
to define the desired daylight saving time amount (minutes).
9 Press the OK button to validate your configuration or configure the parameters
of daylight saving time by Date (see page 78) or by Rule (see page 78).

EIO0000000614 09/2012 77
Daylight Saving Time Setting by Date
If Date is selected in step 7 of Changing the Date/Time (see page 77), follow this
procedure to set the daylight saving time parameters:

Step Action
1 Follow the procedure of Changing the Date/Time (see Magelis Small Panels,
HMI STO User Manual) til step 9.
2 In Add Time press the up/down arrows to select the desired month and press
the right field to display the keypad to define the desired day to add time.
In @ press any of the fields to display the keypad and define the hour to add
time.
3 In Subtract Time press the up/down arrows to select the desired month and
press the right field to display the keypad to define the desired day to subtract
time.
In @ press any of the fields to display the keypad and define the hour to
subtract time.

Daylight Saving Time Setting by Rule


If Rule is selected in step 7 of Changing the Date/Time (see page 77), follow this
procedure to set the daylight saving time parameters:

Step Action
1 Follow the procedure of Changing the Date/Time (see Magelis Small Panels,
HMI STO User Manual) til step 9.
2 In Add Time press the up/down arrows to select the desired day and the
desired month to add tlme.
In @ press any of the fields to display the keypad and define the hour to add
time.
3 In Subtract Time press the up/down arrows to select the desired day and the
desired month to subtract time.
In @ press any of the fields to display the keypad and define the hour to
subtract time.

Forcing a Restart

Step Action
1 In the Setting menu, press the System tab.
2 Press the Restart button, the following message appears: Are you sure you
want to restart the operating system?.
3 Press the Restart button to restart the unit or the Cancel button to return to the
System menu.

78 EIO0000000614 09/2012
Selecting a Language
The following table describes how to select the language used for the Settings
menu, the run-time messages and user application.

Step Action
1 In the Setting menu, press the System tab.
2 Press the Language button.
3 Press the up/down arrows to select the desired languages for:
z System,
z User Application,
z Keyboard Language.

The languages available in the language settings are defined in the Vijeo
Designer editor.
4 Press OK to validate.

Displaying Version Information

Step Action
1 In the Setting menu, press the System tab.
2 Press the Ver. Info button, version information displays:
z Vijeo-Designer Runtime Version,
z Vijeo-Designer Version,
z build number.

Displaying Memory Statistics

Step Action
1 In the Setting menu, press the System tab.
2 Press the Memory button.
z DRAM describes the amount of memory currently being used by the
application.
z Main Flash indicates the amount of internal memory (flash memory)
required to store the runtime system files and the user application.

Brightness Control

Step Action
1 In the Setting menu, press the System tab.
2 Press the Brightness button.
3 Press the up/down arrows to adjust the brightness.
NOTE: Reducing the brightness could increase the life span of the backlight.

EIO0000000614 09/2012 79
Offline Settings

Introduction
The offline settings cannot be changed while a user application is running.

Changing the Network Settings

Step Action
1 In the Setting menu press the Offline tab.
2 Press the Network button, the following message appears: Working with
Offline Settings will stop the user application and runtime. Continue?
3 Press the OK button to restart the system or the Cancel button to return to the
System menu.
4 In the Static IP tab, press any of IP Address, Subnet Mask or Default
Gateway fields, a numerical keypad displays, enter the desired parameters and
validate by pressing Enter button.
5 In the DHCP tab, press the Enable DHCP checkbox to obtain configuration
information from the network. This reduces system administration workload,
allowing devices to be added to the network with little or no manual intervention.
6 In the MAC/DNS tab:
z Press Obtain DNS Setting checkbox to translate names into IP addresses.
z Press any of IP Address fields, a numerical keypad displays, entry the
desired IP address and validate by Enter button.
7 In Static IP tab press the Ok button to validate.

Changing the Buzzer Settings

Step Action
1 In the Setting menu press the Offline tab.
2 Press the Buzzer button, the following message appears: Working with
Offline Settings will stop the user application and runtime. Continue?
3 Press the OK button to restart the system or the Cancel button to return to the
System menu.
4 Press the desired buzzer mode. The factory setting is Pressing Touch
Object.
z None: Selecting this turns the buzzer off.
z When Press Touch Object: The buzzer only sounds when a Touch Object
is pressed.

80 EIO0000000614 09/2012
Changing Backlight Control

Step Action
1 In the Setting menu press the Offline tab.
2 Press the Backlight button, the following message appears: Working with
Offline Settings will stop the user application and runtime. Continue?
3 Press the OK button to restart the system or the Cancel button to return to the
System menu.
4 In the Backlight control, define the backlight operations.
z Wait: To extend the life of the backlight, you can set up the unit so that it
turns off the backlight when the panel is inactive (idle) for the defined period
of time, (Idle means the unit panel has not been pressed). The factory setting
for this item is off.
z Enable Touch if Backlight Burned Out: This setting defines whether the
press panel is enabled or disabled when a backlight burnout is detected.
When this feature is cleared and the backlight burns out, press inputs are
ignored to prevent operation detected errors. The factory setting for this item
is off.
5 To turn the Backlight off automatically after a specified period of time, press the
Wait checkbox and then set the idle time.

Self Test

Step Action
1 In the Setting menu, press the Offline tab.
2 Press the Self Test button, the following message appears: Working with
Offline Settings will stop the user application and runtime. Continue?
3 Press the OK button to restart the system or the Cancel button to return to the
System menu.
4 In the Self Test control, press:
z Char. Pattern: to check the characters in each font set available on the unit.
Use this test when characters (usually 2-byte characters) do not display
properly.
Ok appears if there is no detected error.
NG appears if there is a detected error.
z Disp. Pattern: to test your LCD screen with some graphical test patterns.
z Touch Panel: to test the touch panel cells. Each cell highlights when it is
pressed during the test.
z COM 1: to test the COM 1 port connector.
Ok appears if there is no detected error.
NG appears if an error is detected.
z Video memory: to test hardware memory.

EIO0000000614 09/2012 81
Driver Configuration

Step Action
1 In the Setting menu, press the Offline tab.
2 Press the IO Manager button, the following message appears: Working with
Offline Settings will stop the user application and runtime. Continue?
3 Press the OK button to restart the system or the Cancel button to return to the
System menu.
4 In the IO Manager control, press the Driver Config button.
5 In the Driver Config control:
Select Driver: press the up/down arrow to select the desired driver.
6 Set the parameters of the selected driver.

Equipment Configuration

Step Action
1 In the Setting menu, press the Offline tab.
2 Press the IO Manager button, the following message appears: Working with
Offline Settings will stop the user application and runtime. Continue?
3 Press the OK button to restart the system, or the Cancel button to return to the
Setting menu.
4 In the IO Manager control, press the Equipment Config button.
5 In the Equipment Config control:
Select Equipment: press the up/down arrow to select the desired equipment.
6 Set the parameters of the selected equipment.

82 EIO0000000614 09/2012
Diagnostics Settings

Introduction
The HMI STU 655/855 units are equipped with a number of diagnostic features that
can be used to check the systems and the interfaces for any problems.

Diagnostics
See the Vijeo Designer online help for information on accessing the Diagnostics
Settings menu.

Variables
Use the Variable menu to check that the application is running correctly. The
following table describes how to get to the Variable menu:

Step Action
1 In the Settings menu, press the Diagnostics tab.
2 Press the Variable button.
3 Select Equipment: press the up/down arrow to select the equipment whose
variables you want to test.
4 In the Variable menu, press the Go Offscan button, the following message
appears:
Warning: Entering the Variable Test screen pauses communication with
all equipment. Continue?
5 Press the OK button to restart the system, or the Cancel button to return to the
Variable menu.
6 If the Go Onscan is pressed, the test reads the value for each variable
associated with the selected equipment. If any of the variables detects a
problem, because of a detected error in the equipment or a time-out, the event
log displays a message with the name of the variable.
7 After you complete testing variables from one equipment, you can continue
testing variables for other equipment connected to the target machine.
8 Alternatively, you can test all equipment at once by selecting Test All in the
Select Equipment drop-down list.
9 Press the Return button to return to the Diagnostics menu.

EIO0000000614 09/2012 83
Statistics
Use the Statistics menu to check the connection between equipment. The following
table describes how to get to Statistics menu:

Step Action
1 In the Settings menu, press the Diagnostics tab.
2 Press the Statistics button.
NOTE:
When you write any value to this system control word, press the Rollover
button to:
z Copy the values in the current statistic variables to the previous statistic
variables.
z Reset current statistic variables to zero.

3 In Show Stats for: press the up/down arrow to select the equipment whose
variables you want to show statistics for.
4 Press the right arrow button to view the next display.
5 Press the Go Offscan button to start the test.
6 Press the right arrow button to view the next display.
7 Total Good: the total number of received variables without detected error.
Total Bad: the total number of detected errors of all types.
Total Count: Total Good + Total Bad.
No Reply: no reply was received in response to the request.
Chksum Fail: received a request or response (1) with an incorrect checksum.
Wrong Addr.: received a request or response (1) with an incorrect address.
Error Resp.: received a detected error response from the equipment.
(1): Master-type drivers send out requests and receive responses. Slave-type
drivers receive requests and send responses.
8 Press the next arrow button to view the next display.
9 Inv. Resp.: received a response that contained a protocol detected error.
Init. Fail: initializing communications with the equipment was unsuccessful.
Write Fail: writing a new value to the equipment was unsuccessful.
Intrn Error: internal driver detected error indicates improper driver
configuration or driver problem.
Xmit Fail: transmitting a request or response was unsuccessful.
Unsupp. Req.: received a request for an unsupported service.
Inv. Request: received a request that contained a protocol detected error.
10 Press the Return button to return to the Diagnostics menu or the previous
arrow button to view the previous display.

84 EIO0000000614 09/2012
Magelis HMI STU 655/855

EIO0000000614 09/2012

Troubleshooting

5
Overview
This chapter describes how to find and resolve detected problems with the
HMI STU 655/855 units.

What Is in This Chapter?


This chapter contains the following topics:
Topic Page
Troubleshooting Checklists 86
Self Test List 89

EIO0000000614 09/2012 85
Troubleshooting Checklists

Introduction
When there is a detected problem, go through the checklist and follow the
instructions given.
Here are the main detected problems that may occur when using HMI STU 655/855
unit.
z Panel display is blank,
z Connected equipment cannot be used,
z Panel does not respond or responds very slowly,
z Panel beeps when powered on,
z Cannot change the date or time.

NOTE: Contact your local Schneider Electric vendor or your local distributor.

Panel Display is Blank


If the unit display is blank, perform the following check steps:

Step Check/Operation Solution


1 Are all Vijeo Designer screens You may have to download the screens
downloaded? again.
2 Is the Initial Panel ID set up correctly in Enter the Initial Panel ID in the Vijeo
Vijeo Designer? Designer editor and download again.
3 Is the unit using the correct rated Verify the power supply connections and
voltage? levels.
4 Is the power supply off or disconnected? Follow the instructions in this manual for
reconnecting the power supply.
5 Is the backlight lit? Potential detected problem with the unit.
Contact your local Schneider Electric
distributor.
6 Is the detected problem resolved? If none of the previous steps fixed the
blank panel display detected problem,
then verify the hardware.

86 EIO0000000614 09/2012
Connected Equipment Cannot be Used
If the unit does not communicate with connected equipment, perform the following
check steps:

Step Check/Operation Solution


1 Is the power supply off or disconnected? Verify the power supply connections and
levels.
2 Do the Driver and Equipment settings In the Vijeo Designer editor Navigator
in Vijeo Designer match the actual window’s Project tab, expand the I/O
equipment you are trying to Manager node to enter the correct
communicate with? configuration settings for the Driver and
Equipment nodes.
3 Is the communication cable connected Refer to the associated protocol manual
correctly? for information about cable diagrams.
4 Is the detected problem resolved? If none of the previous steps fixed the
communication detected problem, then
verify the hardware.

Unit does not respond when pressed


If the unit is either not responding when pressed or if its response time is very slow,
perform the following check steps:

Step Check/Operation Solution


1 Disconnect all the cables except the -
power cable.
2 In the Settings menu, press the Offline If the test is unsuccessful, there is a
tab and then press the Self Test icon. detected problem with the hardware.
Run the Touch Panel test.
3 If touch response is slow, does it happen If the panel displays the values of a large
on a specific panel? number of equipment variables, you may
want to redesign the panel and separate
the variables into different panels and
download again.

EIO0000000614 09/2012 87
Step Check/Operation Solution
4 If touch response is slow, the target CPU To resolve this detected problem, try
may be very busy communicating with each of the following in the Vijeo
external equipment. Designer editor and download again.
z If you are using serial
communication, verify the
communication speed between the
target and equipment is optimized.
z In the equipment or scan group
properties, reduce the Scan Rate to
Slow. This will reduce the frequency
of variable updates to 1000 ms.
z If you use many equipment variables
in application scripts, you may want to
change the script to a panel script so
that the variables are active only
when the information is necessary.
If none of the above works, then you may
have to reduce the number of external
variables in the project.
If none of the proposed options work,
contact your Schneider Electric
Technical Support for optimizing your
project.

Target beeps when powered ON


A continuous beep from the target means that system files are corrupted. To resolve
this detected problem, go to the Vijeo Designer Start menu and run Recovery on the
target machine.

88 EIO0000000614 09/2012
Self Test List

Introduction
The HMI STU 655/855 units are equipped with a number of diagnostic features that
can be used to check the systems and the interfaces for any detected s.

Self Test
From the Settings menu, press the Offline button and then the Self Test icon. Self
Test menu appears. See the Vijeo Designer online help for information on accessing
the Offline tab.

Self Tests
The following tests can be accessed from the Self Test menu.

Test Description
Char. Pattern Checks the characters in each font set available on the unit. Use this test
when characters (usually 2-byte characters) are not displayed properly.
OK appears if there is no detected error; NG appears if there is a
detected error.
Disp. Pattern Use this test when your drawings are not displayed properly.
Touch Panel Tests the touch panel cells. Each cell highlights when it is pressed
during the test.
COM 1 Checks that the serial port (RS-232C and RS-485) is working properly.
To run the check, you may need to connect a loopback cable (see
below).
OK appears if there is no detected error; a detected error message
appears if there is an error.
Video Memory Use this test to check the video memory (memory used for screen
display). Run this test when the screen does not display properly.
OK appears if there is no detected error; NG appears if there is a
detected error.

Wiring for COM 1 tests


When testing the serial port, depending on which port and which communication
format you are testing, you may need to attach a loopback cable with wiring as
defined below:

RS-232C RS-485
HMI STU 655/855 in COM1 Not available.
RXD 1
TXD 2

EIO0000000614 09/2012 89
90 EIO0000000614 09/2012
Magelis HMI STU 655/855

EIO0000000614 09/2012

Maintenance

6
Overview
This chapter explains how to maintain your HMI STU 655/855 units.

What Is in This Chapter?


This chapter contains the following topics:
Topic Page
Regular Cleaning 92
Periodic Check Points 94

EIO0000000614 09/2012 91
Regular Cleaning

Cleaning the display

NOTICE
EQUIPMENT DAMAGE
z Power off the unit before cleaning it.
z Do not use hard or pointed objects to operate the touch panel, since it can
damage the panel surface.
z Do not use paint thinner, organic solvents, or a strong acid compound to clean
the unit.
Failure to follow these instructions can result in equipment damage.

When the surface or the frame of the display gets dirty, soak a soft cloth in water
with a neutral detergent, wring the cloth tightly and wipe the display.

92 EIO0000000614 09/2012
Chemical Substances
The products in the following table can be used when cleaning the unit:

Kinds of fluid Company Product Concentration Temperature ° C (° F) pH Value


designation
Cleaning agents Ecolab Topmaxx 422 5 40 (104) 1% : pH=13
in the food and Ecolab P3 Topax M 95 5 40 (104) 1% : pH=12.3
beverage industry
Ecolab P3 Oxonia Active 3 40 (104)
Ecolab P3 Topax 52 FR 5 40 (104) 1% : pH=2
Ecolab P3 Topax 36 5 40 (104)
Ecolab P3 Luboklar MH 0.7 40 (104)
Johnson Divosan 2000 1 25 (77) 100% : pH=7
Diversey
Johnson Diverfoam 5 25 (77) 3% : pH=8.3
Diversey Septiplus
Johnson Acifoam 5 25 (77) 1% : pH=2.2
Diversey
Johnson HD Plus Foam 5 25 (77) 1% : pH=12.9
Diversey
Johnson Oxofoam 5 25 (77) 1% : pH=12.7
Diversey
Johnson Endoroplus VE6 5 25 (77) 1% : pH=12.1
Diversey
Johnson Endoroforce VE2 5 25 (77) 1% : pH=12.5
Diversey
Johnson Endorocid VE10 5 25 (77) 1% : pH=2
Diversey
Diverse Water 100 50 (122)
Milk 100 25 (77)
Methanol 10 25 (77)
Oils ASTM 1 100 25 (77)
IRM 902 100 25 (77)
IRM 903 100 25 (77)
Cerechlor/IRM 903 50/50 25 (77)
Syntopon B 3 25 (77)

EIO0000000614 09/2012 93
Kinds of fluid Company Product Concentration Temperature ° C (° F) pH Value
designation
Cutting oils Ecocut HBN 16LE Pure 25 (77)
Quakercool 7101H Emulsion 25 (77)
Quakercool 2769 Soluble / 25 (77)
Synthetic
Quakercool 3750H Micro-emulsion 25 (77)

Periodic Check Points

Operation Environment
Refer to the Environmental Specifications (see page 30).

Electrical Specifications
The input voltage must be within 20.4 to 28.8 Vdc.

Related Items
z Are all power cords and cables connected properly? Are there any loose cables?
z Are all mounting brackets holding the unit securely?
z Are there scratches or traces of dirt on the installation gasket?

94 EIO0000000614 09/2012
Magelis HMI STU 655/855
Index
EIO0000000614 09/2012

Index
B
AC
Symbols I
Peripherals Installation
Edit Mode, 25 Procedures, 51

A M
Accessories, 16 Maintenance
Check points, 94
Cleaning, 92
C
Certifications and Standards, 23
Connecting the Power Cord, 56 P
Connecting the Power Supply, 59 Part number
HMI STU 655, 12
HMI STU 855, 12
D Parts Identification and Functions, 19
Diagnostics Settings, 83 Power plug, 56

E S
Edit Mode Peripherals, 25 Self Test, 89
Ethernet Settings
Cable connector, 72 menu, 76
Specifications
COM, 38
G COM1, 37, 38
Grounding, 61 Display, 33
General, 30
Interfaces, 37
Memory, 37, 37
USB, 37, 37
System Settings, 77

EIO0000000614 09/2012 95
Index

T
Troubleshooting, 86

U
USB
Data Transfer Cable, 65
Mini-B, 70
Port, 64
Standard A, 67

96 EIO0000000614 09/2012

You might also like