Textbook of Electrotherapy 2nd Ed Jagmohan Singh

Textbook of
Electrotherapy
Textbook of
Electrotherapy
Second Edition
Jagmohan Singh PhD

Professor and Principal
Gian Sagar College of Physiotherapy
Ram Nagar, Rajpura
Patiala, Punjab, India
JAYPEE BROTHERS MEDICAL PUBLISHERS (P) LTD

New Delhi Panama City London Dhaka Kathmandu

Jaypee Brothers Medical Publishers (P) Ltd
Headquarters
Jaypee Brothers Medical Publishers (P) Ltd
4838/24, Ansari Road, Daryaganj
New Delhi 110 002, India
Phone: +91-11-43574357
Fax: +91-11-43574314
Email: jaypee@jaypeebrothers.com
Overseas Offices
J.P. Medical Ltd Jaypee-Highlights Medical Publishers Inc.
83 Victoria Street, London City of Knowledge, Bld. 237, Clayton
SW1H 0HW (UK) Panama City, Panama
Phone: +44-2031708910 Phone: +507-301-0496
Fax: +02-03-0086180 Fax: +507-301-0499
Email: info@jpmedpub.com Email: cservice@jphmedical.com
Jaypee Brothers Medical Publishers (P) Ltd Jaypee Brothers Medical Publishers (P) Ltd
17/1-B Babar Road, Block-B, Shaymali Shorakhute, Kathmandu
Mohammadpur, Dhaka-1207 Nepal
Bangladesh Phone: +00977-9841528578
Mobile: +08801912003485 Email: jaypee.nepal@gmail.com
Email: jaypeedhaka@gmail.com
Website: www.jaypeebrothers.com
Website: www.jaypeedigital.com
2012, Jaypee Brothers Medical Publishers
All rights reserved. No part of this book may be reproduced in any form or by any means without the prior permission
of the publisher.
Inquiries for bulk sales may be solicited at: jaypee@jaypeebrothers.com
This book has been published in good faith that the contents provided by the author contained herein are original, and is
intended for educational purposes only. While every effort is made to ensure accuracy of information, the publisher and
the author specifically disclaim any damage, liability, or loss incurred, directly or indirectly, from the use or application
of any of the contents of this work. If not specifically stated, all figures and tables are courtesy of the author. Where
appropriate, the readers should consult with a specialist or contact the manufacturer of the drug or device.
Textbook of Electrotherapy
First Edition: 2005
Second Edition: 2012
ISBN 978-93-5025-959-7
Printed at
Dedicated to
My Parents, Teachers, Friends, Students, Wife
and
My Daughters Jinia & Jinisha
Preface to the Second Edition
Textbook of Electrotherapy Second Edition has been designed to cater to the long-pending
needs of students of Bachelor of Physiotherapy (BPT) especially 1st and 2nd year and also
of 3rd and 4th year. The book is also useful for professionals of physiotherapy, teachers,
doctors, rehabilitation professionals, other paramedics and public in general.
The book has been compiled and prepared as per the curriculum of Electrotherapy for
BPT degree courses devised by the following Universities: Baba Farid University of Health
Sciences, Faridkot, Tamil Nadu; Dr MGR Medical University, Chennai, Tamil Nadu; Rajiv
Gandhi University of Health Sciences (RGUHS), Bengaluru; Manipal Academy of Higher
Education (MAHE), Manipal; NTR University of Health Sciences, Vijayawada, Andhra
Pradesh; Guru Nanak Dev University, Amritsar, Punjab; Punjab University, Chandigarh;
Punjabi University, Patiala; Postgraduate Institute of Medical Education and Research
(PGIMER), Chandigarh; Choudhary Charan Singh (CCS) University, Meerut, Uttar Pradesh;
HNB University, Srinagar, Garhwal, Uttaranchal; University of Allahabad; Dr Bhim Rao
Ambedkar University, Agra; Guru Jambheshwar University, Hisar, Haryana; Kurukshetra
University, Kurukshetra, Haryana; Nagpur University, Nagpur; University of Pune, Pune;
Devi Ahilya University, Indore, Madhya Pradesh; University of Delhi; GGS Indraprastha
University, New Delhi; Jamia Hamdard, New Delhi; Utkal University, Bhubaneshwar,
Odisha; University of Calcutta, Kolkata, West Bengal; Sri Ramachandra Medical Centre
(SRMC), Chennai, Tamil Nadu; Alagappa University, Karaikudi, Tamil Nadu, etc.
Not many books on Electrotherapy are available, especially the books which is written
for the students studying physiotherapy. This subject is essential and is a basic subject
of physiotherapy for the undergraduate and as well as for the postgraduate courses.
A limited number of textbooks are available in the markets, which are suitable for the
students. To avoid confusion in understanding each topic of the entire subject, Textbook of
Electrotherapy has been written in a systematic manner in a very simple approach for the
students, professionals of physiotherapy, teachers, doctors, rehabilitation professionals,
other paramedics and public in general. Recently, lots of advances have taken place in the
field of electrotherapy. Utmost efforts have been made to cover all the necessary aspects of
electrotherapy. All chapters have been written in a very simple and lucid manner.
In ancient times, two modes of treatmentsphysical therapy and chemotherapy
were available to mankind, i.e. treatment by physical means and treatment by chemical
means. Physical means included the use of sun, earth, air, water, electricity, etc. Chemical
means included chemical agents which were therapeutically useful for clinical purposes.
Electrotherapy is an ever-advancing field. Recent advances have made electrotherapy very
interesting, lots of new modalities have been found effective for the treatment of various
ailments. Utmost efforts have been made to make the textbook up-to-date. Starting from
the history of electrotherapy to the recent advances, all the aspects have been covered in
details.
viii Textbook of Electrotherapy
I have tried to give a fairly complete coverage of the subject describing the most
common modalities known to be employed by physiotherapists. The intention is to
explain how these modalities work and their effects upon the patient. In the initial chapter,
I have tried to lay the foundations of the principles of electrotherapy because a thorough
understanding of these principles will ultimately lead to safer and more effective clinical
practice. The nature, production, effects and uses on the body tissues of each modality are
explained and illustrated.
Chapter One covers the Basics of Electricity, Light and Sound. Starting from the origin of
Electricity, to the use in various experiments in sciences, to the conduction of electricity
in nerves and contraction of muscles, all basic aspects have been covered in details.
Fundamental principles of electricity have been explained in details, i.e. Ohms Law,
Coulombs Law, Law of conservation of energy, quantization of electricity, etc. Static
electricity and current electricity has also been explained. Thermal and chemical effects
of currents, magnetic effects of currents and electromagnetic waves have also been added.
Physical principles of Light and Sound has been added.
Chapter Two covers the Low Frequency Currents. Starting from faradic type current,
modified faradic current, iontophoresis, commonly used ions and their indications for use,
methods of treatment, safety and precautions have also been included. TENS, types of
TENS, methods of treatment, indications for use, dangers and contraindications, MENS
are also added. Indications for the use of low frequency currents and physiological effects
of low frequency currents have been explained in detail.
Methods of treatment are the special features of the book. Comprehensive proforma
for the assessment of the patients condition has been formulated for the convenience
of the students. Methods of median nerve stimulation, ulnar nerve stimulation, radial
nerve stimulation, Erbs paralysis, facial nerve stimulation, deltoid inhibition, quadriceps
inhibition, lateral popliteal nerve stimulation, faradism under pressure and faradic foot
bath have been explained in detail. Common motor points have also been demonstrated.
Chapter Three covers the Middle Frequency Currents. Interferential therapy, methods
of treatment, advantages of interferential currents, physiological effects of interferential
therapy have been explained in detail. Russian currents and Rebox-type currents are also
explained.
Chapter Four covers the High Frequency Currents. Short wave diathermy, methods of
applications, indications for use, physiological effects, therapeutic effects, dangers and
contraindications are explained in detail.
Microwave diathermy, methods of applications, indications for use, physiological
effects, therapeutic effects, dangers and contraindications are also explained in this chapter.
Long Wave Diathermy has been added.
Chapter Five covers the Radiation Therapy. Infrared therapy, ultraviolet radiation, types
of generators, methods of applications, indications for use, physiological effects, thera-
peutic effects, dangers and contraindications have been explained in detail.
Chapter Six covers the Laser Therapy. Production of lasers, types of lasers, methods
of application, indications for use, physiological effects, therapeutic effects, dangers and
contraindications have been explained in detail.
Chapter Seven covers the Superficial Heating Modalities. Its composition, methods
of applications, indications for use, physiological effects, therapeutic effects, dangers
Preface to the Second Edition ix
and contraindications have been explained in detail. Hot packs, electric heating packs,
whirlpool bath, contrast bath, heliotherapy and sauna bath have also been explained.
Chapter Eight covers the Ultrasonic Therapy. The production of ultrasound, thermal and
mechanical effects of ultrasound, methods of applications, indications for use, physiological
effects, therapeutic effects, dangers and contraindications have been explained in detail.
Shockwave Therapy is also added.
Chapter Nine covers the Cryotherapy. Methods of applications, indications for use,
physiological effects, therapeutic effects, dangers and contraindications have been explained
in detail.
Chapter Ten covers the Biofeedback. Its instrumentation, types of biofeedback, effects
and uses, indications for use.
Chapter Eleven covers the Electromyography. Its instrumentation, uses, study of
electromyograph, spontaneous potential, insertional activity, motor unit action potential
and recruitment pattern, abnormal potentials, spontaneous activity, positive sharp waves,
fasciculation potential, and repetitive discharges have been explained in details.
Nerve conduction velocity, its instrumentation, sensory nerve conduction velocity,
motor nerve conduction velocity, methods of stimulation and recording have also been
included. The H reflex, F wave, and their clinical significance have also been explained.
Kinesiological Electromyography, surface and fine wire recording, placement of electrodes
and its clinical importance have been explained.
Glossary of terms, Suggested Reading and Index are also given at the end of this book.
Any suggestions from the teachers and students will be highly appreciated so that
further improvements in the title can be made in the subsequent edition in the light of the
same.
Jagmohan Singh
Preface to the First Edition
The book titled Textbook of Electrotherapy has been designed to cater the long-pending
needs of students of bachelor of physiotherapy especially 1st and 2nd year and also of 3rd
and 4th year. The book is also useful for professionals of physiotherapy, teachers, doctors,
rehabilitation professionals, other paramedics and public in general.
This book has been compiled and prepared as per the curriculum of Electrotherapy for
BPT degree courses devised by the following Universities: Baba Farid University of Health
Sciences, Faridkot; Tamil Nadu Dr MGR Medical University, Chennai; Rajiv Gandhi
University of Health Sciences, Bangalore; Manipal Academy of Higher Education, Manipal;
NTR University of Health Sciences, Vijayavada; Guru Nanak Dev University, Amritsar;
Punjab University, Chandigarh; Punjabi University, Patiala; PGIMER, Chandigarh; CCS
University, Meerut; HNB Garhwal University, Srinagar, Garhwal (UA); University of
Allahabad; Dr Bhim Rao Ambedkar University, Agra; Guru Jambheshwar University,
Hisar (Haryana); Kurukshetra University, Kurukshetra (Haryana); Nagpur University,
Nagpur; University of Pune, Pune; Devi Ahilya University, Indore (MP); University of
Delhi; GGS Indraprastha University, New Delhi; Jamia Hamdard, New Delhi; Utkal
University, Bhubaneshwar, Odisha; University of Calcutta; SRMC, Chennai; Alagappa
University, Karaikudi; etc.
Not many books on Electrotherapy are available in India, especially the book which is
written for the students studying physiotherapy in India. This subject is essential and is a
basic subject of physiotherapy for the undergraduate and as well as for the postgraduate
courses. Very few books by the Indian authors are available. A limited number of textbooks
are available in the market, which are suitable for the students. To avoid confusion in
understanding each topic of the entire subject; this Textbook of Electrotherapy has been
written in a systematic manner in a very simple approach for the students, professionals
of physiotherapy, teachers, doctors, rehabilitation professionals, other paramedics and
public in general. Recently, lots of advances have taken place in the field of electrotherapy.
Utmost efforts have been made to cover all the necessary aspects of electrotherapy. All
chapters have been written in a very simple and lucid manner.
In ancient times, two modes of treatmentsphysical therapy and chemotherapy
were available to mankind, i.e. treatment by physical means and treatment by chemical
means. Physical means includes the use of sun, earth, air, water, electricity, etc. Chemical
means includes chemical agents which were therapeutically useful for clinical purposes.
Electrotherapy is an ever-advancing field. Recent advances have made electrotherapy very
interesting, lots of new modalities have been found effective for the treatment of various
ailments. Utmost efforts have been made to make this textbook up-to-date. Starting from
the history of electrotherapy to the recent advances, all the aspects have been covered in
details.
xii Textbook of Electrotherapy
I have tried to give a fairly complete coverage of the subject describing the most
common modalities known to be employed by physiotherapists. The intention is to
explain how these modalities work and their effects upon the patient. In the initial chapter,
I have tried to lay the foundations of the principles of electrotherapy because a thorough
understanding of these principles will ultimately lead to safer and more effective clinical
practice. The nature, production, effects and uses on the body tissues of each modality are
explained and illustrated.
Chapter One covers the Introduction of Electrotherapy. Starting from the origin of
electricity, to the use in various experiments in sciences, to the conduction of electricity
in nerves and contraction of muscles, all basic aspects have been covered in details.
Fundamental principles of electricity have been explained in details, i.e. Ohms Law,
Coulombs Law, Law of conservation of energy, quantization of electricity, etc. Static
electricity and current electricity has also been explained. Thermal and chemical effects
of currents, magnetic effects of currents and electromagnetic waves have also been added.
Chapter Two covers the Low frequency currents. Starting form faradic type current,
modified faradic current, electrotherapeutic currents including alternating, direct and
pulsed currents, interrupted direct current, evenly alternating currents including sinusoidal
currents and didynamic currents, interrupted ialvanic current to the electrical nerve
stimulation, accommodation, effects of frequency of stimulation, strength of contraction,
pathological changes in peripheral nerve, seddons classification of nerve injuries, process
of denervation and regeneration of nerve. Different waveforms, waveform shape, pulse vs
phases and direction of current flow, pulse amplitude, pulse charge, pulse rate of rise and
decay time, asymmetric waveforms, exponential current, pulse duration, pulse frequency
and current modulations have also been added in this Chapter. Indications for the use
of low frequency currents and physiological effects of low frequency currents have been
explained in details.
Methods of treatment are the special features of this book. Comprehensive proforma
for the assessment of the patients condition has been formulated for the convenience
of the students. Methods of median nerve stimulation, ulnar nerve stimulation, radial
nerve stimulation, Erbs paralysis, facial nerve stimulation, deltoid inhibition, quadriceps
inhibition, lateral popliteal nerve stimulation, faradism under pressure and faradic foot
bath have been explained in details. Common motor points have also been demonstrated.
Iontophoresis, commonly used ions and their indications for use, methods of treatment,
safety and precautions have also been included. TENS, type of TENS, methods of treatment,
indications for use, dangers and contraindications are also added.
Chapter Three covers the Middle Frequency Currents. Interferential therapy, methods
of treatment, advantages of interferential currents, physiological effects of interferential
therapy have been explained in details. Russian currents and Rebox-type currents are also
explained.
Chapter Four covers the High Frequency Currents. Short wave diathermy, methods
of application, indications for use, physiological effects, therapeutic effects, dangers and
contraindications are explained in details.
Microwave diathermy, methods of application, Indications for use, physiological effects,
therapeutic effects, dangers and contraindications are also explained in this Chapter.
Preface to the First Edition xiii
Chapter Five covers the Radiation Therapy. Infrared therapy, ultraviolet radiation,
types of generators, methods of applications, indications for use, physiological effects,
therapeutic effects, dangers and contraindications have been explained in details.
Chapter Six covers the Laser Therapy. Production of lasers, types of lasers, methods
of applications, indications for use, physiological effects, therapeutic effects, dangers and
contraindications have been explained in details.
Chapter Seven covers the Paraffin-wax Bath Therapy and Other Healing Modalities. Its
composition, methods of applications, indications for use, physiological effects, therapeutic
effects, dangers and contraindications have been explained in details. Hot packs, electric
heating peaks, whirlpool bath, contrast bath, heliotherapy and sauna bath have also been
explained.
Chapter Eight covers the Ultrasonic Therapy. The production of ultrasound, thermal
and mechanical effects of ultrasound, methods of applications, indications for use,
physiological effects, therapeutic effects, dangers and contraindications have been
Chapter Nine covers the Cryotherapy. Methods of applications, indications for use,
physiological effects, therapeutic effects, dangers and contraindications have been
Chapter Ten covers the Biofeedback. Its instrumentation, types of biofeedback, effects
and uses, indications for use.
Chapter Eleven covers the EMG, NCV and Evoked Potentials. Its instrumentation, uses,
study of electromyograph, spontaneous potential, insertional activity, motor unit action
potential and recruitment pattern, abnormal potentials, spontaneous activity, positive
sharp waves, fasciculation potential, and repetitive discharges have been explained in
details.
Nerve conduction velocity, its instrumentation, sensory nerve conduction velocity,
motor nerve conduction velocity, methods of stimulation and recording has also been
included. The H reflex, F wave, and their clinical significance have also been explained.
Kinesiological Electromyography, surface and fine wire recording, placement of electrodes
and its clinical importance have been explained.
Glossary of terms, Suggested Reading and Index are also given at the end of this book.
Any suggestions from the teachers and students will be highly appreciated so that
further improvements in the title can be made in the subsequent edition in the light of the
same.
Jagmohan Singh
Acknowledgments
Textbook of Electrotherapy is a book that provides practical knowledge of the basic principles
and techniques along with updated knowledge of the important aspects of electrotherapy.
I am indebted to Dr Sukhwinder Singh, Vice Chairman and Dr JP Singh, Director, Gian
Sagar Educational and Charitable Trust for encouraging me and providing me support for
writing this book.
I also express my sincere gratitude to Dr AS Sekhon, Dean Colleges, Gian Sagar Group
of Institutions and Dr Kamaljit Singh, CEO, Gian Sagar Educational and Charitable Trust
for their support and cooperation.
I am thankful to my teachers Dr AG Dhandapani, Dr PP Mohanty, Dr Monalisa Pattnaik
Mohanty, Dr Nanda, and Dr C Misra who taught me the basics of Physiotherapy.
I am thankful to my guide and mentor Dr Jaspal Singh Sandhu, Dean, Professor and
Head, Department of Sports Medicine and Physiotherapy, Guru Nanak Dev University,
Amritsar, Dr MS Sohal, Ex-Professor and Head, Department of Physiotherapy and Sports
Sciences, Punjabi University, Patiala and Dr Paramvir Singh, Associate Professor and
Head, Department of Sports Sciences, Punjabi University, Patiala for encouraging me at
every step of my life.
I am thankful to Dr Satwinder Kalra, Dr KEM Benzamin, and Dr AG Sinha; their
comments are of great value for elevating the profession of physiotherapy.
I am thankful to Dr Deepak Kumar, Dr Manish Arora, Dr Narkeesh Arumugham,
Dr GD Singh, Dr Jitendra Sharma, Dr Harihara Prakash, Dr Lalit Arora, Dr Reena Arora,
Dr Hemant Juneja, Dr Raju Sharma, Dr Pawas Jaiswal, Dr D Vijay Kumar, Dr Aruna Ravipati,
Dr Uma Shankar Mohanty, Dr Sandeep Singh, Dr Sonia Singh, Dr Ramasubramania
Raja, Dr Navkiran, Dr Sanjay, Dr Sabita, Dr Smarak Mishra, Dr Dayanand Kiran,
Dr Anand Mishra, Dr Ram Prasad, Dr Deepali, Dr Navinder Singh, Dr Gagandeep Singh,
Dr K Prabhu, Dr A Prabhu, Dr Rajni Arora, Dr AM Bhardwaj, Dr Surjit Chakrabarty,
Dr Rati, Dr Jaspreet Vij and Dr Manu Goyal for their support.
This book is a complete, authoritative, latest and easily readable book. This book
has been designed to effectively meet the needs and requirements of the undergraduate
students. The book focuses on the basic principles and their application to the clinical
practice.
In preparing the book, I have utilized the knowledge of a number of stalwarts in my
profession and consulted many books and authors. I wish to express my appreciation and
gratitude towards all of them.
I have made every effort to keep the book comprehensive without eliminating basic
information. The emphasis has been laid entirely on accuracy, authenticity, simplicity and
reproducibility by the student. How far I have succeeded in my efforts is for students and
teachers to judge. I shall welcome their suggestions and comments.
xvi Textbook of Electrotherapy
I especially thank my colleagues Dr M Neethi, Dr Janarthanan Reddy, Dr Anu Sharma,

Dr Rajiv Sharma, Dr Amandeep Singh, Dr Bhanu, Dr Manpreet, Dr Shainy, Dr Sukhjinder
Singh, and Dr Amit Gupta for their support and cooperation towards the successful
completion of the book.
I especially thank Dr Ranbir Dhull, Shri Ashok Sharma and Mrs Lalita Aneja for their
whole-hearted support.
I owe my special thanks to Shri Jitendar P Vij, Chairman and Managing Director and
his whole team for publishing the book in such a nice manner.
My thanks also go to my students, viz. Dr Manpreet, Dr Gagandeep, Dr Gursharanjit,
Dr Irvan, Dr Jasmeet, Dr Jasmeen, Dr Navjot, Dr Indermeet Singh, Dr Inderpal Singh,
Dr Shallu, Dr Navpreet, Dr Sukhmeet, Dr Sachleen, Dr Aman Navneet, Dr Vishesh,
Dr Iftikhar, Dr Neha, Dr Bavleen, Dr Pavneet, Dr Sakshi, Dr Bhanupriya, Dr Aakshi,
Dr Prabhdeep, Dr Amanpreet, Dr Manjinder, Dr Shilpa and others for their enthusiasm for
learning, which has inspired me a lot.
My thanks go to my wife Dr Harpreet Kaur for always having picked me up whenever
I have needed and who endured three years of emotional stress, while I was deeply
engrossed in preparing the book.
Contents
1. Basic Electricity, Light and Sound 1

The Structure of an Atom 3

The Formation of Compounds 4

Types of Electricity 6

Static Electricity 6

Capacitance 10

Current Electricity 12

Thermal and Chemical Effects of Currents 19

Magnetic Effects of Electric Current 30

Magnets and Earth Magnetism 40

Electromagnetic Induction 47

Electric Shock 62

Physical Principles of Light 65

Physical Principles of Sound 71

2. Low Frequency Currents 75

Faradic Type Current 75

Electrotherapeutic Currents 76

Waveforms 85

Current Modulation 89

Indications for the use of Low Frequency Currents 90

Physiological Effects of Low Frequency Currents 92

Methods of Treatment 94

Treatment of Patients Condition 94

Proforma for Patients Assessment 94

Median Nerve Stimulation 98

Ulnar Nerve Stimulation 101

Radial Nerve Stimulation 104

Erbs Paralysis 106

Facial Nerve Stimulation 108

Deltoid Inhibition 111

Quadriceps Inhibition 112

Lateral Popliteal Nerve Injury 113

Faradism Under Pressure 115

Faradic Foot Bath 116

xviii Textbook of Electrotherapy
Common Motor Points

119

Strength Duration Curve 124

Iontophoresis 128

Transcutaneous Electrical Nerve Stimulation 129

Microcurrent Electrical Neuromuscular Stimulation 134

3. Medium Frequency Currents 135

Rebox-type Currents 135

Russian Currents 135

Interferential Therapy 136




Low Back Pain 143

Periarthritis Shoulder 145

Osteoarthritis Knee 147

Absorption of Exudates 148

Stress Incontinence 149

4. High Frequency Currents 151

Diathermy 151

Short Wave Diathermy 151

Capacitor Field Method 154

Cable Method or Inductothermy 161

Physiological Effects of Heating the Tissues 163

Therapeutic Effects of Short Wave Diathermy 164

Dangers of Short Wave Diathermy 166

Contraindications of Short Wave Diathermy 168

Pulsed Short Wave Diathermy 169

Microwave Diathermy 169

Long Wave Diathermy 172


Treatment of the Patients Condition 173


Cervical Spondylosis 175

Periarthritis Shoulder 177

Low Back Ache 179

Lumbar Spondylosis 182

Short Wave Diathermy to Hip Joint 183

Sciatica 184

Osteoarthritis of Knee 185

Secondary Osteoarthritis 186

Contents xix
Ligament Injuries 188

Plantar Fasciitis 192

Salpingitis (Pelvic Inflammatory Disease) 194

5. Radiation Therapy 196

Infrared Radiations 196

Dangers of Infrared Radiations 201

Contraindications 202



Infrared Radiations 202


Low Back Ache 204

Postimmobilization Stiffness 207

Absorption of Exudates or Edema 208

The Ultraviolet Radiations 209

Production of Ultraviolet Radiations 209

Techniques of Application 211

Techniques of General Irradiation 212

Physiological Effects of Ultraviolet Radiations 212

Indications of Ultraviolet Irradiations 213




Ultraviolet Radiations 216


Ulcers 218

Acne Vulgaris 220

Pressure Sores 221

Psoriasis 221

Rickets 223

General Debilitating Condition 223

Vitiligo 224

Alopecia 224

Sensitizers 224

6. Laser Therapy 226




Tennis Elbow (Lateral Epicondylitis) 234

Supraspinatus Tendinitis 235

xx Textbook of Electrotherapy
Golfers Elbow (Medial Epicondylitis)

236

Plantar Fasciitis 236

7. Superficial Heating Modalities 237

Paraffin Wax Bath Therapy 237


Hotpacks/Hydrocollator Packs 240

Electric Heating Pads 241

Whirlpool Bath 241

Contrast Bath 242

Heliotherapy 243

Sauna Bath 243

8. Ultrasonic Therapy 245

Techniques and Methods of Application 252

Physiological Effects of Ultrasound 257

Therapeutic Uses of Ultrasound 259

Dangers of Ultrasound 260


Phonophoresis 262

Combination Therapy 264

Shock Wave Therapy 265



Ultrasound Therapy 267


Tennis Elbow (Lateral Epicondylitis) 268

Golfers Elbow (Medial Epicondylitis) 269

Supraspinatus Tendinitis 270

De Quervains Disease (Tenosynovitis) 270

Bicipital Tendinitis 271

Subdeltoid Bursitis 271

Subacromial Bursitis 272

Metatarsalgia 272

9. Cryotherapy 273

Physiological Effects and Therapeutic Uses of Cold Therapy 276

Dangers and Contraindications 277


Ankle Sprain 278

Muscle Contusion/Hematoma 279

Contents xxi
10. Biofeedback 281

11. Electromyography 287
The Electromyographic Examination 293
Kinesiological Electromyography 296
Nerve Conduction Velocity 296
Glossary 305
Suggested Reading 315
Index 317
Basic Electricity,
1 Light and Sound
Introduction
Physiotherapy is the means of treating disorders by physical means. Electrotherapy is an
integral part of physiotherapy. The use of electricity for therapeutic purposes has grown
up in recent years and now includes a wide variety of apparatus and equipments. A large
number of therapeutic modalities for treating several disorders are now in use.
The evolution of electricity for therapeutic purposes starts way back in 1646 when Thomas
Rown coined the term Electricity. After this period there was a rapid development in the
field of electricity. It became possible to store electricity for experiments. The important
names during this period that contributed to these achievements included Pieter Van
Musschenvoroek of Leyden, Benjamin Franklin of Philadelphia and Luigi Galavani of
Bologna (Cherington et al. 1994).
Benjamin Franklin was a great thinker and statesman at the time of the American revo-
lution. In 1752, he conducted famous kite experiment. Franklin charged his Leyden jar
by using a kite during electrical storms. During that period, electricity has become a
source of Astonishment and Amusement. Franklins analysis of Leyden jar lead to the
discovery of the law of electrostatic induction. He postulated the two opposing forces
of electricity, i.e. positive and negative charges.
In 1780 Luigi Galvani a professor of Anatomy proceeded his work on animal electricity.
Galvani discovered that the nerves are a good conductor of electricity. He stimulated
nerve of a frog with a knife during an experiment. This study revealed the relationship
between electrical stimulation of nerve and contraction of its muscle.
In 1826 George Simon Ohm establishes the result which is now known as Ohms law.
He stated that the current flowing through a metallic conductor is proportional to the
potential difference across its ends, provided the physical conditions remain constant.
In 1833 Guillaume Duchenne demonstrated that the muscle can be stimulated percu-
taneously. He was the first to systematically study the neuromuscular diseases and
was first to study the muscular dystrophies. Duchenne was considered as the inventor
of muscle nerve electricity or localized faradizations and considered as father of
modern Electrotherapy.
In 1840 Englands first Electrotherapy department was established at Guys Hospital
under Dr Golding Bird. The use of Galvanic currents were first documented there.
2 Textbook of Electrotherapy
In 1843 Emil Du Bois Reymond introduced the technique of stimulating nerve and
muscle by means of a short duration (faradic) current from the modified induction
coil. He was the first to demonstrate that there is change in polarity of nerve when it is
stimulated. He is considered as father of modern electrophysiology.
In 1849 LeDuc introduced interrupted direct current.
In 1858 Remak discovered that the points where the nerve enters into a muscle were
easy to stimulate.
In 1859 Baierlacher reported that a paralysed muscle responded to galvanic but not
faradic current.
In 1861 Erb introduced the method of electrodiagnosis based on faradic and galvanic
currents. Erb was the first to demonstrate increase electrical irritability of motor nerves
in tetany which in known as Erbs phenomenon. He was also the first to electrically
stimulate the brachial plexus. This is how evolution of electricity in the use of nerve
muscle stimulation has taken place.
In 1864 Keningsberg reported the important role of duration of current in eliciting the
muscle contraction. He developed a mechanical device which could rapidly interrupt the
current; if the rate of interruption exceeded the limit, there was no muscle contraction.
In 1891 Nicola Tesla presented a paper in Electrical Engineer about medical applica-
tion of High Frequency Currents. He observed when the body is transversed by alter-
nating currents above a certain frequency, heat is perceived.
In 1892 Arsene D Arsonval of France developed an apparatus capable of producing
High Frequency Currents, he was the first person to study the effects of High Frequency
Currents on humans. In a communication to Biological Society of France he wrote that
a current with frequency greater than 10,000 Hz can be passed through a body without
producing any other sensation other than heat.
In 1892 Weiss first attempted to produce a rectangular pulse using ballistic rheotome.
In 1907 Lapicque defined rheobase as minimal continuous current intensity required
for muscle excitation. He also defined chronaxie which is the minimal current duration
required at an intensity twice the rheobase.
In 1908 Nagel Schmidt was the first person to coin the term Diathermy. He performed
several experiments independently over animal models and demonstrated the deep
heating effects of diathermy.
In 1910 Langevin produced the first piezoelectric generator for emitting ultrasound.
In 1916 Adrian was the first to demonstrate strength duration curve. He noted that
healthy muscles showed a fairly constant curve. There was a predictable shift of the
curves during muscle degeneration as well as in different phases of recovery.
In 1928 A W Hull invented the magnetron.
In 1946 Frank H Krusen and his coworkers reported first clinical use of microwave
diathermy.
In 1965 Melzack and Wall first postulated the pain gate theory.
Basic Electricity, Light and Sound 3
In 1972 Meyer and Fields were the first to report the clinical use of TENS for relief of
chronic pain.
In 1982 Melzack and Wall further modified their famous pain gate theory.
In 1985 Cummings performed several experiments on rat to see the effects of LASER.
His experiments suggested the use of LASER on wounds and ulcer healing.
In 1991 Erwin Neher and Bert Sakmann developed a technique that detects electrical
currents in the membrane of the cell, establishing the existence of ion channels. They
developed a device called Patch-clamp apparatus to record the small electrical poten-
tial of the cell. They were awarded Nobel prize in Physiology and Medicine for their
discoveries.
The Structure of an Atom

The structure of matter that shapes the world around us has been a subject of study since
long. The first contribution came from John Dalton (1808), who postulated that matter
is composed of atoms. The structure of atom was first described by J J Thompson (1897)
and later modified by Rutherford (1911) and Neil Bohr (1940). Historically, they were
described as minute individual particles but the quantum physics has explained the
existence of many subatomic particles.
An Atom
An atom can be described as the smallest particle of an element. It contains the central
nucleus in which two particles protons and neutrons are held together by strong nuclear
forces and are surrounded by negatively charged particles called electrons. The diameter
of the atom is of the order of 1010 m.
The Nucleus
The whole mass of an atom is concentrated in the central part called the nucleus. Its diam-
eter ranges from 1015 m to 1014 m. It consists of positively charged protons and neutral
charged neutrons. The proton and neutron are regarded as two different charge state of
same particle called neucleon. As the atom is electrically neutral, the number of electrons in
the atom is equal to the number of protons inside the nucleus.
The Proton
Protons were discovered by Gold stein (1900). They are comparatively larger in size and
bears a positive charge. It is the positive charge of proton which gives the nucleus of an
atom an over all positive charge. Number of protons in the nucleus determines the element
of which it is an atom and is called the atomic number. For example, the atomic number of
hydrogen is 1.
The Neutron
Neutrons were discovered by James Chadwick (1932). The neutrons possess no charge
and are therefore electrically neutral. Usually, the number of neutrons approximately
equals a number of protons but in larger elements there are more neutrons than protons.
The sum of protons and neutrons in the nucleus gives rise to the atomic mass.
In certain elements, it is possible for different atoms to have different number of
neutrons in their nuclei with the same number of protons. These are called Isotopes of an
element. For example, carbon with atomic number 6 may have atomic masses 12, 13 or 14.
So an isotope is an atom of an element with same number of protons but different number
of neutrons.
The Electron
Electrons were discovered by J. J. Thomson (1897). Electrons are negatively charged
particles found revolving around the nucleus in fixed orbits. Although electrons are very
small (1/1837 mass of a proton), they are responsible for various physical and chemical
activities of an atom.
A force of attraction between nucleus and electron is very strong. Therefore, these
electrons are tightly bound with the nucleus. These electrons lie close to nucleus and are
called bound electrons. As the distance between the nucleus and electrons increases, force
of attraction decreases. It means that there is an inverse relation between force of attraction
and the distance between the two.
1
F
d2
As the number of orbits increases, the force of attraction between nucleus and electron
weakens and therefore, the last orbit electrons are bounded by weak force and as a result
of which these electrons remain free and are known as free electrons. Transfer of these free
electrons makes the body charged.
The Formation of Compounds

A compound is a substance formed by the union of two or more elements via the electrons
of the atoms involved to form a molecule of the compound. Compounds may be either be
electrovalent or covalent.
a. Electrovalent compounds: These are formed when an atom of one element gives an
electron to the atom of another element. These atoms are then held together by their
opposite electrical charges, e.g. NaCl.
b. Covalent compounds: These are formed when the outer shells of atoms of the elements
share a number of common or bonding electrons so that each atom has a complete
outer shell, e.g. Methane.
The Conductors and Non-conductors of Electricity

Conductors: Conductors are elements whose atoms have few electrons in their outer
orbit. For example, copper has a single loosely held electron in its outer orbit. It is such
conducting electrons which facilitate the passage of an electric current.
Non-conductors (Insulators): are materials made of atoms in which the electrons in the
outer shell are firmly held in their orbits and do not leave the atom in order to conduct the
current.
States of Matter
Matter can be solid, liquid or gaseous. The molecules of a substance are attracted by
cohesive forces (force of attraction in molecules of same substance) and kinetic forces
(force of movement of molecules).
In Solids: There is a strong cohesive force which holds them in a rigid lattice formation
so that shape remains same or constant. The kinetic force produces vibration of molecules
about a mean position.
In Liquids: When considerable amount of energy is applied to liquid, cohesive force
decreases and kinetic force increases so that its structure collapses and liquid state is
reached.
In Gases: If even more heat is applied, there comes a point when, kinetic force is greater
than cohesive force. Then molecules fly apart and form a gas. The molecules collide with
each other and with the walls of the container, so that the pressure increases. As a result,
temperature increases.
Latent heat: It is the energy required for (or released by) a change of state.
Latent heat of fusion is the amount of heat required to convert 1 gm of ice at 0 degree
Celsius to 1 gm of water at 0 degree Celsius (value is 336 joules).
Latent heat of vaporization is the amount of heat required to convert 1 gm of water at
100 degree Celsius to 1 gm of steam at 100 degree Celsius (value is 2268 joules).
Transmission of Heat
Conduction: If one end of a solid metal rod is heated, the energy added causes an increased
vibration of molecules. This is transmitted and thus, heat is conducted from area of high
temperature to area of low temperature, e.g. metals.
Convection: If one part of a fluid is heated, the kinetic energy of the molecules in that
part is increased, they move further apart and this part becomes less dense. As a result it
rises, displacing the more dense fluid above which descends to take its place. The current
produced is called convection current. For example, it takes place in fluids.
Radiation: As a substance is heated, it causes the electron to move to the higher-energy shell.
As it returns to its normal shell, the energy is released as a pulse of infrared electromagnetic
energy. For example, heat may be transmitted by infrared electromagnetic radiation.
Types of Electricity
1. Static Electricity:
When the charges on a body do not flow, then it is called static electricity.
2. Current Electricity:
When charges flow through a conductor, it is known as current electricity.
Charges: There are two types of chargespositive and negative.
Static Electricity
The simplest way of producing a static electric charge is to rub two materials together. If
the materials involved are insulators, the charges are held on the surfaces of objects and
spread themselves evenly over the surfaces unless there are points or corners, at which
charges tend to concentrate.
Experiments to prove the existence of charge:
Experiment-1: Take a glass rod and a silk cloth. Rub glass rod on silk cloth. After
rubbing hang it with the help of non-metallic string. Take another ebonite rod and
repeat this experiment. Bring it close to hanged rod; we see force of repulsion between
them.
Experiment-2: Take ebonite rod and a woolen cloth. Rub the rod on woolen cloth and hang
it with the help of non-metallic string. Take another ebonite rod and repeat the above
process. Bring it close to first hang rod; we observe the property of force of repulsion.
Experiment-3: Take a glass rod and a silk cloth. Rub the rod on the silk cloth. Hang it with
the help of a non-metallic string. Now take an ebonite rod and a woolen cloth. Rub these
with each other and bring this rod close to the glass rod; we observe the property of force
of attraction.
Conclusion: On the basis of these experiments, we conclude that charge is produced on
glass rod. Later, American scientist Benjamin Franklin (1706 1790) confirms these charges
as positive and negative charges. When glass rod is rubbed with silk, charge produced on
glass rod is known as positive charge. When ebonite rod is rubbed on woolen cloth, charge
produced on ebonite rod is known as negative charge.
We may conclude that like charges repel each other but unlike charges attract each other.
Other Methods of Producing Electricity

According to the law of conservation of energy, energy can neither be created nor be destroyed,
but can be converted from one form to another. When it is produced by friction, mechanical
energy is converted into electrical energy. When it is produced in dry cells, chemical energy
is converted into electrical energy, etc.
Quantization of Electric Charge

The quantization of electric charge is the property by virtue of which any charge exists
only in discrete lumps or packets or bundles of certain minimum charge e, where e is the
charge of an electron and +e is the charge of a proton. The least charge found on any body
is equal to the charge of electron or proton.
e = 1.6 109 coulomb
Also, charge on any body can only be the integral multiple of the charge of electron, i.e.
q = ne
where n is an integer 1, 2, 3,.
Coulombs Law
According to this law, the force of interaction between any two point charges is directly propor-
tional to the product of charges and inversely proportional to the square of distance between them.
Suppose two bodies having charges q1 and q2 are separated in vacuum by a distance r.
Let their linear dimensions be much smaller than the distance r so that they act as point
charges.
According to Coulombs law
F q1 q2/r
F = K q1 q2/r
Where, K is electrostatic force constant.
Coulombs Law of electrostatic force between two charges corresponds to the Newtons
Law of Gravitational force between two masses, i.e.
F = G m1 m2/r
A unit charge is that much charge which when placed in vacuum at a distance of one
meter from an equal and similar charge would repel it with a force of 9 109 Newton.
Electric Field Intensity due to a Group of Charges

The electric field intensity at any point due to a group of point charges is equal to the
vector sum of the electrical field intensities due to the individual charges at the same point.

E = E 1 + E 2 + E 2 + .......... E n
Electric Lines of Forces

Michael Faraday invented the idea of electric lines of force. They give us partial qualitative
information about an electric field. We may define an electric line of force as a path, straight or
curved, such that tangent to it at any point gives the direction of electric field intensity at that point.
Infact, it is the path along which a unit positive charge actually moves in the electrostatic
field, if free to do so.
In Figure 1.1, AB is an electrostatic lineof force. The tangent to the line at any point P
gives us the direction

of electric intensity E p at P. Similarly, tangent to AB at Q gives us
the direction of E q.
It is important to note here that the lines of force do not actually exist, but what they
represent is a reality.
Figure 1.2 shows some lines of force due to single positive point charge. These are
directed radially outwards. The lines of force extend to infinity.
On the contrary, lines of force due to singly negative point charge are directed radially
inwards, Figure 1.3.
Figure 1.4 shows lines of force due to a pair of equal and opposite charges. The lines
of force due to two equal positive point charges of different strength are shown in Figures
1.5 and 1.6.
When the charges are equal, P lies at the centre of the line joining the charges. However,
when the charges are unequal, the neutral point P is closer to the smaller charge. Figure 1.7
shows lines of force for a section of an infinitely large sheet of positive charge.
Properties of Electric Lines of Forces

Electric lines of force are discontinuous curves. They start form a positively charged body
and end at a negatively charged body. No electric lines of force exit inside the charged body.
Fig. 1.1: Electric lines Fig. 1.2: Lines of force Fig.1.3: Lines of force
of forces due to positive charge due to negative charge
Fig. 1.4: Lines of force due to pair Fig. 1.5: Lines of force due to pair of equal
of equal and opposite charges charges
Fig. 1.6: Lines of force due to pair of equal Fig. 1.7: Lines of force due to large sheet
charges but of greater strength
1. Tangent to the line of force at any point gives the direction of electric intensity at that
point.
2. No two electric lines of force can intersect each other. This is because at the point of
intersection P, we can draw two tangents PA and PB to the two lines of force, Figure
1.8. This would mean two directions of electric intensity at the same point, which is not
possible. Hence no two lines of force can cross each other.
3. The electric lines of force are always normal to the surface of a conductor, both while
starting and ending on the conductor. Therefore, there is no component of electric field
intensity parallel to the surface of the conductor.
4. The electric lines of force contract longitudinally, on account of attraction between unlike
changes.
5. The electric lines of force exert a lateral pressure on account of repulsion between like
charges.
Electric Dipole: An electric dipole consists of a pair of equal and opposite point charges
separated by a very small distance. Atoms or molecules of ammonia, water, alcohol, carbon
dioxide, HCI, etc. are some of the examples of electric dipoles, because in their cases, the
centres of positive and negative charge distributions are separated by some small distance.
Figure 1.9 shows an electric dipole consisting of two equal and opposite point charges (q)
separated by a small distance 2a.
Fig. 1.8: Tangents to two lines of Fig. 1.9: Electric dipole

force

Dipole moment: Dipole moment (p ) is a measure of the strength of electric dipole. It is a
vector quantity whose magnitude is equal to product to the magnitude of either charge or
the distance between them. i.e.

p = q (2a )

or|p| = q (2a)

The direction of p is from negative charge to positive charge. The S.I. unit of dipole
moment is Coulomb-metre. (C-m).
If charge q gets larger; and the distance 2a gets smaller and smaller, keeping the product

|p| = q 2a = constant, we get what is called an ideal dipole. Thus, an ideal dipole is the
smallest dipole having almost no size.
Dipole Field: The dipole field is the electric field produced by an electric dipole. It is the
space around the dipole in which the electric effect of the dipole can be experienced. To
calculate dipole field intensity at any point, we imagine a unit positive charge held at that
point. We calculate force on this charge due to each charge of the dipole and take vector
sum of the two forces. This gives us dipole field intensity at that point.
Capacitance
The capacitance of an object is the ability of the body to hold an electrical charge. The unit
of capacitance is farad.
A farad is the capacity of an object which is charged to a potential of 1 volt by 1 coulomb of
electricity.
In practice, microfarad is used most commonly (1 microfarad = 1/1000000 farad).
At any stage, if q is the charge on the conductor and V is the potential of the conductor,
then
qV
q = CV
where, C is a constant of proportionality and is called capacity or capacitance of the
conductor. The value of C depends on the shape and size of the conductor and also on the
nature of the medium in which the capacitance is located.
Factors affecting capacity of a conductor:
1. Area of conductor: It is inversely related to capacity.
2. Presence of any conductor nearby: In this case, potential decreases, so capacity increases.
3. Medium around conductor: The capacity increases when any other medium is placed
around conductor.
Parallel plate capacitor is the capacitor which is used most commonly. It consists of two
thin conducting plates of area A, held parallel to each other, suitable distance d apart. The
plates are separated by an insulating medium like air, paper, mica, glass, etc. or dielectric
constant k (Fig. 1.10).
Spherical capacitor consists of a hollow conducting sphere A of radius Ra surrounded by
another concentric conducting spherical shell B of radius Rb (Fig. 1.11).
Variable capacitor consists of two sets of plates interleaving with one another, constructed
in such a way that one set of plates can be moved relative to the other, thus varying the
Fig. 1.10: Paralllel plate capacitor Fig. 1.11: Spherical capacitor
surface area of the plates facing each other. When all the surfaces of both the sets of plates
are fully interleaved, the capacitance is maximum. Variable sets are found in radio sets and
short wave diathermy machine.
Grouping of Capacitors: In many electrical circuits, capacitors are to be grouped suitably
to obtain the desired capacitance. Two most commonly used modes of grouping of capacitors
are: Series and parallel.
1. Capacitors in Series: A voltage applied across four capacitors in series induces charges
of +Q and Q on the plates of each. As we know:
1/C = V/Q
The potential difference across the row is the sum of the potentials across each capacitor
and so, the single capacitance C equivalent to the three capacitors C1, C2, C3 is given by as
in Figure 1.12.
1/C = (V1 + V2 + V3 + V4)/Q
= V1/Q + V2/Q + V3/Q + V4/Q
= 1/C1 + 1/C2 + 1/C3 + 1/C4.
Fig. 1.12: Capacitors in series
2. Capacitors in parallel: If capacitors are connected in parallel, the total charge developed
on them is the sum of the charges on each of them. The effective capacitance is given by as
in Figure 1.13.
C = Q/V
Where Q = Q1 + Q2 + Q3 + Q4
And so,
C = Q1/V + Q2/V + Q3/V + Q4/V
= C1 + C2 + C3 + C4
Fig. 1.13: Capacitors in parallel
Current Electricity
When charges flow through a conductor, the study of this is known as current electricity.
Electric Current
The flow of charge in a conductor is known as electric current.
The essentials for the production of electric current are:
1. Potential difference
2. Pathway along which current can move.
Electric Potential: The electric potential of a body is the condition of that body when
compared to the neutral potential of the Earth. Its unit is the volt.
1 Volt is that EMF which when applied to a conductor with a resistance of 1 ohm produces a current
of 1 ampere. In simple words, it is the repelling power between the charges.
Potential Gradient: The rate of change of potential with respect to distance is called potential
gradient. It is directed from an area of low potential to an area of high potential. It is a vector
quantity.
E = v/d
Where,
E = Potential gradient
v = potential of that point
d = distance
From this equation we conclude that potential gradient can be increased by bringing
two plates together.
The Current Carriers

The charged particles whose flow in a definite direction constitutes the electric current are
called current carriers.
Current carriers in solid conductors: In solid conductors like metals, the valence electrons of
the atoms do not remain attached to individual atoms but are free to move throughout the
volume of the conductor. Under the effect of an external electric field, the valence electrons
move in a definite direction causing electric current in the conductors. Thus, valence
electrons are the current carriers in solid conductors.
Current carriers in liquids: In an electrolyte like CuSO4 NaCl, etc. there are positively and
negatively charged ions (like Cu++, SO4 , Na+, Cl). These are forced to move in definite
directions under the effect of an external electric field, causing electric current. Thus,
current carriers in liquids are positive and negative charged ions.
Current carriers in gases: Ordinarily, the gases are insulators of electricity. But they can be
ionized by applying a high potential difference at low pressures or by their exposures to
X-rays, etc. The ionized gas contains positive ions and electrons. Thus, positive ions and
electrons are the current carriers in gases.
Electromotive Force
It is the force producing the flow of electrons from the more negative to the less negative
body, if similar bodies are charged with different quantities of electricity.
If a pathway is provided, the EMF produces a flow of electrons, but if there is no pathway,
so that no current can pass, the force still exists. The greater the potential difference the
greater is the EMF, and both are measured in the same unit, i.e. the volt.
A volt is that EMF which when applied to a conductor with a resistance of one Ohm
produces a current of one Ampere.
Electrons move only so long as a potential difference exists between the ends of the
pathway, i.e. so long as the EMF is maintained. A potential difference can be produced by
friction, but when a pathway is completed the charges quickly neutralize each other and
current ceases to flow. Other methods of producing a potential difference, and so an EMF,
are by the chemical action in cells, by electromagnetic induction in dynamo, by heat in a
thermocouple and from radiant energy in a photoelectric cell. With all these methods the
potential difference is maintained in spite of the electron flow.
As fast as electrons move away from the negative end of the conductor, they are
replaced by others from the generator, while those which reach the positive end are drawn
away by the generator. Thus, the potential difference is maintained and current continues
to flow.
Electric current: The flow of charge in a definite direction constitutes the electric current
and the time rate of flow of charge through any cross section of a conductor is the measure
of electric current, i.e.
Total charge flowing
Electric current = _____________________________________
Time taken
I = q/t
Unit of electric current: SI unit of electric current is Ampere.
1 Coulomb
1 Ampere = _______________________
1 sec
Thus, the current through a wire is said to be
1 ampere, if one coulomb charge is flowing per
second through a section of the wire.
Direction of electric current: As a matter of conven-
tion, the direction of flow of positive charge gives
the direction of current. This is called conven-
Fig. 1.14: Direction of electric current
tional current. The direction of flow of electrons
gives the direction of electronic current. The
direction of flow of conventional current is opposite to that of electronic current (Fig. 1.14)
Current Density: Current density at a point is defined as the amount of current flowing per
unit are of the conductor around that point provided the area is held in a direction normal
to the current.
Resistance
It is the obstruction to the flow of electrons in a conductor. The unit of electrical resistance
is the ohm. It is the resistance offered to current flow by a column of mercury 1.063 m long
and 1 mm square in cross-section at 0 degree Celsius.
Cause of resistance of a conductor: Resistance of a given conducting wire is due to the
collisions of free electrons with the ions or atoms of the conductor while drifting toward
the positive end of the conductor which in turn depends upon the arrangement of atoms
in the conducting material (silver, copper, etc.) as well as on the length and thickness of the
conducting wire.
Resistance is directly proportional to length and inversely proportional to area of cross-
section, temperature and number of free electrons in a unit volume.
Ohms Law
It was given by a German scientist George Siman Ohm, in the year 1828. It states that,
The current flowing through a metallic conductor is proportional to the potential difference
across its ends, provided that all physical conditions remain constant.
V I
If V = Potential difference and I = current then,
V = IR
where R is resistance and is the constant of proportionality.
Also, R = V/I
So, 1 ohm is defined as the resistance of a body such that 1 volt potential difference
across the body results in a current of 1 ampere through it.
Limitations of Ohms law

1. Temperature of the conductor should remain constant.
2. The conducting body should not be deformed.
3. It takes place in metallic conductors only.
Resistance in Series
If the components of a circuit are connected in series, there is only one possible pathway
for the current, i.e. the components carry the same current. The total resistance equals the
sum of individual resistances (Fig. 1.15).
Fig. 1.15: Resistance in series
If R1, R2, R3 = resistance and V1, V2, V3 = potential difference,

Then from Ohms law, we have,
V1 = IR1
V2 = IR2
V3 = IR3
If potential difference between A and B is V,
Then,
V = V1 + V2 + V3
So,
V = IR1 + IR2 + IR3
V = I(R1 + R2 + R3)
R = R1 + R2 + R3
So, in series combination, equivalent resistance is equal to sum of individual resistances.
Resistance in Parallel
In this case, there are a number of alternative routes offered to the current. However,
potential difference remains the same. It has been found by the application of Ohms law
that the largest resistance carries the smallest current and viceversa.
If 3 resistances R1, R2, R3 are connected in parallel across points A and B. At point A
current I gets divided into I1, I2, and I3 (Fig. 1.16).
Potential difference across A and B is V.
Then from Ohms law,
Fig. 1.16: Resistance in parallel
I = V/R1 + V/R2 + V/R3

I = V (1/R1 + 1/R2 + 1/R3)
V/R = V (1/R1 + 1/R2 + 1/R3)
1/R = 1/R1 + 1/R2 + 1/R3
Hence, in a parallel combination, the reciprocal of equivalent resistance is equal to the
sum of reciprocals of individual resistances.
Electric conductivity: The inverse of resistivity of a conductor is called its conductivity.
The Rheostat
Rheostat is a device used to regulate current by altering either the resistance of the current
or potential in the part of the circuit. It consists of a coil of high resistance wire wound onto
an insulating block with each turn insulated from adjacent turns.
Types
There are two types of rheostat:
1. Series rheostat: In this, the rheostat is wired in series with the apparatus. If all the wires
in the rheostat are included in the circuit, resistance is at its maximum and current at its
lowest. In the physiotherapy department, it is found in the apparatus where an effect
on the degree of heating is required. For example: for wax baths. It is also known as
variable rheostat.
2. Shunt rheostat: It is wired across a source of potential difference and any other circuit
has to be taken off in parallel to it. This apparatus has a current regulating mechanism in
which an electric current is applied directly to the patient, as the current intensity can be
increased gradually from zero upto maximum. It is also known as potentiometer rheostat.
Non-Ohmic Conductors
Those conductors which do not obey the Ohms Law are called the non-Ohmic conductors.
For example, vacuum tubes, semiconductor diode, liquid electrolyte, transistor, etc.
The relation V/I = R is valid for Ohmic and non-Ohmic conductors. The value of R is
constant for Ohmic conductors but not so for non-Ohmic conductors.
Thermistors
A thermistor is a heat sensitive device whose resistivity changes very rapidly with the change
of temperature. The thermistors are usually prepared from the oxides of nickel, copper, iron,
cobalt, etc. These are generally in the form of beads, discs or rods. Pair of platinum leads is
attached at the two ends of the electric connections. This arrangement is sealed in a small
glass bulb. A thermistor can have a resistance in the range of 0.1 Ohm to 107 Ohm, depending
upon its composition. A thermistor can be used over a wide range of temperatures.
Important applications of thermistors:
1. Thermistors can be used to detect small temperature changes. A typical thermistor can
easily measure a change in temperature of 103 C.
2. Thermistors are used to safeguard the filament of the picture tube of a television set
against the variation of electric current.
3. Thermistors are used in temperature control units of industry.
4. Thermistors are used for voltage stabilization.
5. Thermistors are used in the protection of windings of generators, transformers and
motors.
Semiconductors
Semiconductors are elements whose conductivity is between conductors and insulators.
Elements such as germanium, silicon and carbon are insulators of electricity. But when impu-
rities are added to it, they become semiconductors. Semiconductors are insulators at low
temperature. The resistance of semiconductors decreases when the temperature increases.
The process of deliberate addition of impurities to a pure semiconductor to enhance
conductivity is called doping. The impurity atoms are called dopants.
The semiconductors are thus called n-type or p-type. The n-type is with excess of
electrons and p-type is with deficient electron.
Types of Semiconductors
Semiconductors are of two types:
1. Intrinsic semiconductors
2. Extrinsic semiconductors
Intrinsic semiconductors: A pure semiconductor which is free of every impurity is called
intrinsic semiconductor. Germanium and silicon are important examples of intrinsic semi-
conductors which are widely used in electronics industry.
Extrinsic semiconductors: A doped semiconductor or a semiconductor with suitable
impurity atoms added to it is called extrinsic semiconductor.
Extrinsic semiconductor is of two types:
1. N- type semiconductor
2. P-type semiconductor
N-type semiconductor: When a pure semiconductor of silicon (Si) in which each Si atom
has four valence electrons, is doped with a controlled amount of pentavalent atoms, say
arsenic or phosphorous or antimony or bismuth, which have five valence electrons, the
impurity atoms will replace the silicon atoms. The four of the five valence electrons of the
impurity atoms will form covalent bonds by sharing the electrons with the adjoining four
atoms of silicon, while the fifth electron is very loosely bound with the parent impurity
atom and is comparatively free to move (Fig. 1.17).
Fig. 1.17: N-type semiconductor
Thus, each impurity atom added donates one free electron to the crystal structure.
These impurity atoms which donate free electrons for the conduction are called donor
atoms. Since the conduction of electricity is due to the motion of electrons, i.e. negative
charges or n-type carriers, therefore, the resulting semiconductor is called donor-type or
n-type semiconductor. On giving up their fifth electron, the donor atoms become positively
charged. However, the matter remains electrically neutral as a whole.
P-type semiconductor: When a pure semiconductor of silicon (Si) in which atom has
four valence electrons is doped with a controlled amount of trivalent atoms say indium
(In) or boron (B) or aluminium (Al) which have three valence electrons, the impurity atoms
will replace the silicon atoms (Fig. 1.12).
The three valence electrons of the impurity atom will form covalent bonds by sharing
the electrons of the adjoining three atoms of silicon, while there will be one incom-
plete covalent bond with the neighboring Si atom, due to the deficiency of an electron.
This deficiency is completed by taking an electron from one of the Si-Si bonds, thus
completing the In-Si bond. This makes Indium ionized (negatively charged) and creates
a hole. An electron moving from a Si-Si bond to fill a hole, leaves a hole behind. That is
how, holes move in the semiconductor structure. The trivalent atoms are called acceptor
atoms and the conduction of electricity due to motion of holes, i.e. positive charges or
p-type carriers. That is why, the resulting semiconductor is called acceptor type or p-type
semiconductor.
Fig. 1.18: P-type semiconductor
Superconductivity
Prof. K Onnes in 1911 discovered that certain metals and alloys at very low temperature
lose their resistance considerably. This phenomenon is known as superconductivity. As the
temperature decreases, the resistance of the material also decreases, but when the temper-
atures reaches a certain critical value (called critical temperature or transition tempera-
ture), the resistance of the material completely disappears, i.e. it becomes zero. Then the
material behaves as if it is a superconductor and there will be flow of electrons without any
resistance what so ever. The critical temperature is different for different materials. It has
been found that mercury at critical temperature 4.2 K, lead at 7.25 K and niobium at critical
temperature 9.2 K become superconductors.
The cause of superconductivity is that, the free electrons in superconductor are no
longer independent but are mutually dependant and coherent when the critical tempera-
ture is reached. The ionic vibrations which could deflect free electrons in metals are unable
to deflect this coherent or cooperative cloud of electrons in superconductors. It means that
coherent cloud of electrons makes no collisions with ions of the superconductor and, as
such, there is no resistance offered by the superconductor to the flow of electrons.
Applications of Superconductor
1. Superconductors are used for making very strong electromagnets.
2. Superconductivity is used to produce very high speed computers.
3. Superconductors are used for the transmission of electric power.
Thermal and Chemical Effects of Currents

Thermal Effects of the Electric Current
The thermal effect was discovered by James Prescott Joule, a British scientist in the year
1841. He established the law called Joules law.
When current is passed through a conductor, some of its energy is converted into
thermal energy. The amount of heat produced can be calculated using Joules Law which
states that:
The amount of heat produced in a conductor is directly proportional to the square of current, the
resistance, and the time for which the current flows.
This is given by:
Q = IRt
Where, I = current in amperes
R = resistance in Ohms
t = time in seconds.
This equation is known as Joules Law of heating.
Cause of heating effect of current: When a potential difference is applied across the ends of a
conductor, an electric field is set up across its ends and the electric current flows through
it. The large number of free electrons present in the conductor get accelerated toward the
positive end, i.e. in a direction opposite to the electric field developed and acquire kinetic
energy in addition to their own kinetic energy due to their thermal motion. Due to which
an electric current flows through the conductor. These accelerated electrons on their way
suffer frequent collisions with the ions or atoms of the lattice and transfer their gained
kinetic energy to them. As a result of this, the average kinetic energy of vibration of the
ions or atoms of the conductors, rises and consequently the temperature of the conductor
rises. Thus, the conductor gets heated due to flow of electric current through it. Obviously,
the electrical energy supplied by the source of EMF is converted to this heat energy.
Electrical Energy and Power

Energy: Energy is the ability to do work.
According to the Law of conservation of energy, energy can neither be created nor can destroyed.
It only be converted from one form to another.
The amount of work done is given by:
W = E C
Where, W = work done in joules
E = EMF in volts
C = quantity of electricity in coulombs.
Or Electric energy = Power time
W = P t
W = VI t
SI unit of electric energy is Joule, where
1 Joule = 1 volt 1 ampere 1 sec
1 Joule = 1 watt 1 sec
The commercial unit of electric energy is called a Kilowatt-hour (kWh)
1 kWh = 1 kilowatt 1 hour
1 kWh = 1000 watts 1 hour
Thus, 1 kilowatt hour is the total electric energy consumed when an electrical appliance
of power 1 kilowatt works for 1 hour.
1 kWh = 1000 watt hour
1 kWh = 1000 watt 60 60 sec

1 kWh = 3.6 106 Joules
Number of units of electricity consumed
= Number of kilowatt hour
= watt hour/1000
Power: It is the rate of doing work.
Electric power: The rate at which work is done by the source of EMF in maintaining the
current in electric circuit is called the electric power of the circuit.
It is given by:
Power (P) = EMF(E) Current (I)
= I R (as,V = IR)
Also, Power(P) = work/time
Its unit is the watt.
If an EMF of 1 volt moves 1 coulomb of electrons in one second then the power of system is said
to be 1 watt.
Bigger units of power are Kilowatt (103 watts) and Megawatt (106 watts)
Commercial unit of power is Horsepower.
1 Horsepower = 746 watts.
Some aspects of heating effects of currents:
1. The wire supplying current to an electric lamp are not practically heated while that
of the filament of the lamp becomes white hot. We know that, the heat produce
due to a current in a conductor is proportional to its resistance. The lamp and the
supply wires are in series. The resistance of the wires supplying the current to the
lamp is very small as compared to that of the filament of the lamp. Therefore, there
is more heating effect in the filament of the lamp than that in the supply wires. Due
to it, the filament of the lamp becomes white hot where the wires remain practically
unheated.
2. Electric iron, electric heater and heating rod are some of the important household
electric appliances whose working is based on the heating effect of the electric current.
In all such appliances, the heating element used is of a nichrome (an alloy of nickel and
chromium) wire. The wire of nichrome is used because:
i. It has high melting point and high value of specific resistance
ii. It can be easily drawn into wires.
iii. It is not oxidized easily when heated in air.
Electric iron, electric heater and heating rod are of high power instruments. As, electric
power, P = VI. Therefore, for the given voltage V, P I. Thus, the higher is the power of the
electrical appliance, the larger is the current drawn by it. Since the heat produced, H I,
hence the heat produced due to current, is high in both of them.
It should be noted that electric power, P = V/R. Therefore, for the given voltage
V, P I/R. This shows that the resistance of high electric power instrument is smaller
than that of low power.
The heater wire must be of high resistivity and of high melting point. Heat
produced, H = V t/R = V At/l. The resistivity is kept high so that the length l, used
for the given area of cross section of the wire and heat to be produced, may be small.
Nichrome wire is used in heater due to its high resistivity as compared to platinum,
tungsten and copper.
3. Incandescent electric lamp: It consists of metal filament of fine wire (generally of tung-
sten) enclosed in a glass bulb with some inert gas at suitable pressure. The metal filament
must be of very high melting point. When voltage is applied across the bulb, the current
is passed through the filament. The filament gets heated to a very high temperature. It
then becomes white hot (Incandescent state) and then starts emitting white light at once.
4. Fuse wire: A fuse wire is generally prepared from tin-lead alloy (63% tin + 37% lead).
It should have high resistance and low melting point. It is used in series with the
electrical installations and protects them from the strong currents. All of a sudden,
if strong current flows, the fuse wire melt away, causing the breakage in the circuit,
thereby saving the main installations from being damaged. Thus, very cheap fuse wire
is capable of saving very costly appliances.
5. Efficiency of an electric device ()
Efficiency of an electric device is defined as the ratio of its output power to the input
power, i.e.
Output power
= ____________________________
Input power
In case of an electric motor,
Output mechanical power
Efficiency = ________________________________________________
Input electric power
Here, Input electric power = Output mechanical power + Power lost in heat
Efficiency of a battery or cell is maximum when its internal resistance is equal to
external resistance of the circuit.
Chemical Effects of the Electric Current

When we pass current through a solid conductor, it gets heated and also a magnetic field is
produced around the conductor. It shows that there is a heating effect as well as magnetic
effect of current, but there is no chemical effect in a solid conductor. On the other hand if
current is passed through a liquid, it may or may not allow the current to pass through it.
On the basis of electric behavior, the liquids can be classified into three categories.
1. Insulators: These are those liquids which do not allow current to pass through them.
For example, vegetable oil, distilled water, etc.
2. Good conductors: These are those liquids which allow the current to pass through
them but do not dissociate into ions. For example, mercury (a liquid metal at ordinary
temperature).
3. Electrolytes: The liquids which allow current to pass through them and also dissociate
into ions or passing through them are called electrolytes. For example, the solution of
salts, acids and bases in water, alcohol, etc.
Therefore, when current is passed through an electrolyte, it dissociates into positive
and negative ions. This is called chemical effect of electric current and was studied in detail
by Michael Faraday in 1933.
Commonly used terms are:

Electrolysis: The process of decomposition of electrolyte solution into ions on passing the
current through, is called electrolysis.
Electrolyte: The substance which decomposes into positive and negative ions on passing
current through, is called electrolyte. For example: acids, basis, salts, dissolved in water, alcohol,
etc. are common electrolytes. Pure salt like NaCl, KCl are electrolyte, in their molten state.
Electrodes: These are the two metal plates which are partially dipped in the electrolyte for
passing the current through the electrolyte.
Anode: The electrode connected to the positive terminal of the battery, i.e. the electrode at
higher potential is called anode.
Cathode: The electrode connected to the negative terminal of the battery, i.e. the electrode
at lower potential is called is cathode.
The current flows through the electrolyte from anode to cathode.
Ions: The charged constituents of the electrolyte which are liberated on passing current are
called ions.
Anions: The ions which carry negative charge and moves toward the anode during
electrolysis are called anions. The ions formed when chemical reaction involves addition of
electrons (i.e. reduction) are called anions.
Cations: The ions which carry positive charge and move towards the cathode during
electrolysis are called cations. The ions formed when chemical reaction involves removal of
electrons (i.e. oxidation) are called cations.
Voltameter: The vessel in which the electrolysis is carried is called a voltameter. It contains
two electrodes and a solution electrolyte. It is also known as electrolytic cell.
Faradays Laws of Electrolysis

Faraday, from his experimental study, arrived at the two laws of electrolysis which are
given below:
First Law: The mass of the substance liberated or deposited at an electrode during
electrolysis is directly proportional to the quantity of charge passed through the electrolyte.
If m is the mass of a substance deposited or liberated at an electrode during electrolysis
when a charge q passes through the electrolyte, then according to Faradays First Law of
electrolysis
m q
Or m = z q
Where z is a constant of proportionality and is called Electrochemical equivalent (ECE) of the
substance.
If an electric current I flows for a time t to pass the charge q through the electrolyte,
then q = It
m = zIt, when q = l, then m = z l = z
Hence electrochemical equivalent (ECE) of a substance is defined as the mass of the
substance liberated or deposited on an electrode during electrolysis, when one Coulomb
of charge (or 1 ampere current for 1 second) is passed through the electrolyte.
Generally ECE of a substance is expressed in gram/Coulomb (g/C). The value of ECE

of copper and hydrogen are 0.0003294 g/C and 0.0000105 g/C respectively.
Second Law: When the same amount of charge is made to pass through any number
of electrolytes, the masses of the substances liberated or deposited at the electrodes are
proportional to their chemical equivalents.
If m1 and m2 are masses of the substances liberated or deposited on various electrodes,
when same current is passed for the same time through their electrolytes.
E1 and E2 are the chemical equivalents of the substances liberated or deposited.
Then according to the Faradays Second Law of electrolysis
m1/m2 = E1/E2
Faradays Second Law of electrolysis also states that the electrochemical equivalent of
a substance is directly proportional to its chemical equivalent.
If E1 and E2 are the chemical equivalents of the two substances and z1 and z2 are ECE
of those two substances, then according to Faradays Second Law of electrolysis
z1/z2 = E1/E2
Faradays constant:
From Faradays Second Law of electrolysis
zE
or E z
E = Fz
Where, F is Faradays constant
Thus, Faradays constant is
F = E/z
F = E/m/q = qE/m (m = zq)
If m = E , then F = q
Hence, Faradays constant is equal to the amount of charge required to liberate the
mass of a substance at an electrode during electrolysis, equal to its chemical equivalent (in
grams).
Practical application of electrolysis:
1. Electroplating: It is a process of depositing a thin layer of one metal over another
metal by the method of electrolysis. The articles of cheaper metals are coated with
precious metals like silver and gold to make their looks more attractive. The article
to be electroplated is made the cathode and the metal to be deposited is made the
anode. A soluble salt of the precious metal is taken as the electrolyte. When current is
passed, a thin layer of the metal (made anode) is deposited on the article made (made
cathode).
2. Extraction of metals from ores: Certain metals like Aluminium, Copper, Zinc, Magne-
sium, etc. are extracted from their ores by the method of electrolysis.
3. Purification of metals: Impure metals are purified by electrolysis. Blister copper is
purified by this method.
4. Anodising: It is the process of coating aluminium with its oxide electrochemically to protect
it against corrosion. It dilute sulphuric acid as electrolyte, the aluminium article is made the
anode. To give surface of articles beautiful colors, dyes are mixed in the electrolyte.
5. Medical applications: Similar principles of electrolysis are also used in nerve stimula-
tion. Also, similar principles are used for removing unwanted hairs from the body.
Cell
In current electricity, cell means an electrochemical cell. Cell is a device by which chemical
energy is converted into electrical energy. Electrochemical cells are of two types:
1. The primary cells
2. The secondary cells
The primary cells are those in which electrical energy is produced due to chemical
energy. The chemical reaction in the primary cell is irreversible. The examples of primary
cells are Voltaic cell, Daniel cell, Leclanche cell, Dry cell, etc.
The secondary cells are those in which the electrical energy is first stored up as the
chemical energy. When current is required to drawn from the secondary cell, then the
chemical energy is reconverted into the electrical energy. The chemical reaction in the
secondary cell is reversible. The examples of secondary cells are Lead- acid accumulators,
alkali accumulators or Edison cell.
The initial cost of a primary cell is low as compared to the secondary cell. But, the
running cost of a secondary cell is low as compared to the primary cell.
The Primary Cells

Voltaic cell: Voltaic cell was invented by Allexandro de Volta in 1800. It consist of two
rods (called electrodes) one of copper and another of zinc, partly immersed in dilute
sulphuric acid (called electrolyte) contained in a glass vessel (Fig. 1.19). The copper rod
acts as positive electrode and zinc rod acts as negative electrode.
When the electrodes are connected to an external resistor, the circuit is completed.
There will be flow of electrons from the negatively charged zinc rod to the positively
charged copper rod through the external resistor. Now the conventional electric current is
said to flow from copper to zinc.
Daniel cell: It consists of a copper vessel containing saturated copper sulphate solution.
The copper vessel itself acts as the positive electrode or anode. A porous pot containing
10% dilute sulphuric acid (called electrolyte) and amalgamated zinc rod (called cathode),
Fig. 1.19: Voltaic cell

Fig. 1.20: Daniel cell
is placed in the copper vessel and is partly immersed in a copper sulphate solution. The
porous pot prevents the solution from mixing, but allows the hydrogen ions to pass through
it. A perforated shelf containing the copper sulphate crystal is placed at the top of the vessel
in order to keep the concentration of the copper sulphate solution same (Fig. 1.20).
In this cell, as the reaction continues, the concentration of copper sulphate solution
decreases. Some CuSO4 crystals get dissolved immediately from the perforated shelf into
CuSO4 solution. Thus, the concentration of CuSO4 is maintained. As the concentration of
the copper sulphate solution remains constant, when Daniel cell is in use, therefore, its emf
remains constant.
Lechlanche cell: A Lechlanche cell consists of a vessel of glass containing strong solution
of ammonium chloride which acts as electrolyte. An amalgamated zinc rod dipping in
ammonium chloride acts as negative electrode or cathode. A porous pot is placed inside
the glass vessel. The carbon rod placed inside the porous pot acts as positive electrode or
anode. The space in the porous pot is filled with manganese dioxide and charcoal powder
(Fig. 1.21). The charcoal powder makes the manganese dioxide electrically conducting and
manganese dioxide acts as depolarizer. The inner side of glass vessel near the open end
is coated with black paint which works as reflector for the ammonium chloride crystal
as they have the tendency to creap along the glass wall. This helps in maintaining the
proper concentration of ammonium chloride solution. The electrons released are collected
by zinc rod, making it at negative potential with respect to electrolyte. The ammonia gas
so produced escapes. The hydrogen ions diffuse through the porous pot and interact with
manganese dioxide.
The positive charge is transferred to the carbon rod which attains the positive potential
with respect to electrolyte. The depolarizer (MnO2) in Leclanche cell is in solid form and is
slow in action. Therefore, when the current is drawn from the Leclanche cell, the hydrogen
is liberated quickly than MnO2 can use it up. So, after some time, a partial polarization sets
due to accumulation of hydrogen on anode and thereby, the current falls off. When the
circuit is switched off, the hydrogen gas escapes. The cell regains its original emf and is
again ready for use.
Thus, Lechlanche cell is useful in those experiments where intermittent supply of
current is needed.
Fig. 1.21: Lechlanche cell
The emf of Lechlanche cell is 1.45 V and its internal resistance can vary from 0.1 Ohm
to 10 Ohm.
Dry cell: A dry cell is a portable form of Lechlanche cell. It consists of zinc vessel which acts
as a negative electrode or cathode. The vessel contains a moist paste of sawdust saturated
with a solution of ammonium chloride and zinc chloride. The ammonium chloride acts as
an electrolyte and the purpose of zinc chloride is to maintain the moistness of the paste
being highly hygroscopic. The carbon rod covered with the brass cap is placed in the
middle of the vessel. It acts as positive electrode or anode. It is surrounded by a closely
packed mixture of charcoal and manganese dioxide (MnO2) in a muslin bag. Here MnO2
acts as a depolarizer. The zinc vessel is sealed at the top with pitch or shellac. A small hole
is provided in it to allow the gases formed by the chemical action to escape (Fig. 1.22).
The emf of dry cell is 1.5V. If this cell is used continuously, the polarization defect may
develop in this cell but it regains its emf if allowed to rest for a while.
Fig. 1.22: Dry cell

The Secondary Cell

A secondary cell is that cell in which the electrical energy is first stored up as a chemical
energy and when the outside circuit is closed to draw the current from the cell, the chemical
energy is reconverted into electrical energy. The chemical reactions are reversible in this
cell.
The secondary cells are also called storage cells or accumulators because they act in
such a way as if they were reservoir of electricity, i.e. the current can be drawn from them
whenever required and when they are discharged, they can be recharged. The commonly
used secondary cells are Lead-Acid accumulator and Edison cell.
Lead-Acid accumulator: It consists of a glass or hard rubber vessel containing dilute
sulphuric acid (20% conc.), which act as electrolyte. There are two sets of perforated lead
plates arranged alternately parallel to each other inside the vessel (Fig. 1.23). These plates
are held apart by strips of wood or celluloid. Alternate plates are soldered together to one
lead rod forming one electrode while remaining once soldered to another common lead
rod forming another electrode. The holes or perforations in the lead plates are filled with
red lead or lead oxide (PbO2 ).
Fig. 1.23: Secondary cell (lead-acid accumulator)
Charging: Charging means storing of electrical energy. To charge this accumulator a

source of steady current or battery charger is connected across the two terminals of two
electrodes. The electrode which is connected to positive terminal of external source serves
as anode and the other electrode serves as cathode. The dissociation of H2SO4 gives the
H+and SO42. When current is passed through the cell by the help of external source,
hydrogen ions move to the negative electrode (called cathode) and the sulphate ions go to
positive electrode (called anode).
During charging electron moves from the anode to cathode, thus raising the potential
difference between the electrodes. In charging process, water is consumed and sulphuric
acid is formed. When the specific gravity of sulphuric acid solution becomes 1.25, the cell
is fully charged. The emf of the cell at this stage is 2.2 volts.
Discharging: If the cell is connected to the external circuit, the current is drawn from the
cell. The sulphuric acid dissociates into hydrogen ions and sulphate ions. After giving their
charges, they react with the electrodes and reduce the active material of each plate to lead
sulphate.
In discharging process, the electrons moves from the cathode to anode, thus lowering
the potential difference between electrodes. Hence, the emf of cell falls. In this process,
sulphuric acid is consumed and water is formed. Therefore, the specific gravity of sulphuric
acid also falls. If the specific gravity of sulphuric acid falls below 1.18, the cell requires
recharging.
Alkali accumulator (Ni-Fe) or Edison cell: It is also known as alkaline secondary cell or
Edison cell. It consists of a steel vessel containing 20% solution of KOH in distilled water
(as electrolyte) and 1% Lithium hydroxide to make it conducting. Here anode is a perfo-
rated steel plate in the form of a grid. Its holes are packed with nickel hydrochloride and
trace of nickel to make it conducting. The cathode is also made of a steel grid. Its holes
are packed with a iron hydrochloride and trace of mercury oxide for lowering its internal
resistance (Fig. 1.24).
Fig. 1.24: Alkali accumulator or Edison cell
Working: Potassium hydroxide solution breaks up into positive potassium ions and
negative hydroxyl ions due to ionization.
Charging: On passing the current from an external source, the anode attracts negative
hydroxyl ions and cathode attracts positive potassium ions. These ions on reaching the
respective electrodes lose their charge and react with them. Thus, when accumulator is
charged Ni(OH)4 is formed on the anode and a spongy Fe on the cathode. In this process,
electrons moves from anode to cathode, raising the potential difference between the two
electrodes of cell. When this potential difference becomes 1.36 V, the cell is fully charged.
Discharging: When the two electrodes of the cell are connected together through a resistor,
there is discharging of the cell, i.e. the cell is giving the current. Now the anode attracts the
potassium ions and cathode attracts hydroxyl ions. These ions on reaching the respective
electrodes give their charges and react with them. The electrons moves from cathode to
anode, thus lowering the potential difference between two electrodes, due to which emf of
the cell falls. When the emf becomes less than 1.1 V, then the cell requires recharging.
The emf of Ni-Fe cell is 1.36 V. Its internal resistance is low but is higher than net
storage cell.
Advantages
1. It can withstand rough handling.
2. It is lighter, stronger and more durable than the lead accumulator.
3. It is not damaged or over recharged.
4. It is not spoiled even if left uncharged for a long time.
Disadvantages
1. Its initial cost is high.
2. Its emf is smaller and internal resistance is greater than that of lead accumulator. Therefore,
it cannot give us very strong currents.
3. It absorbs carbon dioxide when exposed to atmosphere and thus its capacity is considerably
reduced.
Magnetic effects of electric current

Oersted (1820) showed that the electric current through the wire deflects the magnetic
needle below the wire. The direction of deflection of the magnetic needle is reversed if the
deflection of current in the wire is reversed.
An electric current is equivalent to the charges (or electrons) in motion. Such charges
produce magnetic interaction. The magnetic field produce by the conductor carrying
current thus interacts with the magnetic needle and deflects it (Fig. 1.25).
Fig. 1.25: Magnetic effects of electric current
As a rule, if we imagine a man swimming along the wire in the direction of current
with his face always turned toward the needle, so that the current enters at his feet and
leaves at his head, then the N-pole of the magnetic needle will be deflected toward his left
hand. This rule can be recollected with the help of the word SNOW. It means, current from
South to North, in a wire over the magnetic needle, the north pole of the needle is deflected
toward West.
A magnetic field is the space around a magnet or a space around a conductor carrying
current in which magnetic influence can be experienced. In the later case, the magnetic field
disappears as soon as the current is switched off. It suggests that motion of electrons in the
wire produces a magnetic field. In general, a moving charge is a source of magnetic field.
Due to the interaction between the magnetic field produced due to a moving charge,
i.e. current and the magnetic field applied, the charge q then experiences a force, which
depends upon the following factors (Fig. 1.26):
1. The magnitude of the force F experienced is directly proportional to the magnitude of
the charge, i.e.
F q
2. The magnitude of the force F is directly proportional to the component of velocity
acting perpendicular to the direction of magnetic field, i.e.
F sin .
3. The magnitude of the force F is directly proportional to the magnitude of the magnetic
field applied, i.e.
F B.
Fig. 1.26: Effects on magnitude of force

Thus, combing the above factors, we get
F q sin B
F = k q sin B
Where, k is the constant of proportionality and its value is found to be 1.
F = q sin B

or |F | = q |v B|

or F = q |v B|
It is the equation of a magnetic Lorentz force experienced by a charged particle moving
in the magnetic field.
If = 1, q = 1 and sin = 1
or = 90, then F = 1 1 B 1 = B
Thus, the magnetic field induction at any point in the field is equal to the force acting
on a unit charge moving with a unit velocity perpendicular to the direction of magnetic
field at that point.
In cases where,
1. = 0 or 180, then sin = 0
F = q sin B = 0
Thus, a charged particle moving parallel to the direction of magnetic field, does not
experience any force.
2. If = 0 then
F = q sin B = 0
It means that if a charged particle is at rest in a magnetic field, it experiences no force.
3. If = 90, then sin = 1
F = q (1) B = q B
It means that if a charge particle is moving along a line perpendicular to the direction
of a magnetic field, it experiences a maximum force.
The direction of this force is determined by Flemings Left Hand Rule.
Flemings Left Hand Rule states that: If we stretch the first finger, the central finger and
the thumb of left hand mutually perpendicular to each other such that the first finger
points to the direction of magnetic field, the central finger points to the direction of electric
current (motion of the positive charge) then the thumb represents the direction of force
experienced by the charge particle.
If is along X-axis and B along Y-axis, then F will be along Z-axis (Figs 1.27A and B).
Unit of B in S I units is Tesla (T)
B = F/q sin
If q = 1 C, = 1 m/s , = 90
or sin = 1 and F = 1 N
Then, B = 1/1 1 1 = 1 T
Thus, the magnetic field induction at a point is said to be one Tesla, if a charge of one
coulomb while moving at right angle to a magnetic field, with the velocity of one m/s
experiences a force of one N, at that point.
Biot-Savarts Law
Biot-Savarts Law is an experimental law predicted by Biot and Savart in the year 1820.
This law deals with the magnetic field induction at a point due to a small current element
(a part of any conductor carrying current).
A B
Figs 1.27A and B: Flemings left hand rule

Let AB is a small element of length dl of the conductor XY which is carrying I. Let r

be the position vector of the point P from the current element dl (The current element dl
is a vector which is tangent to the element and is in the direction of current flow in the
conductor) and be the angle dl and r (Fig. 1.28).
Fig. 1.28: Explanation of Biot-Savarts law

According to Biot-Savarts law, the magnetic field induction dB (also called magnetic
flux density) at a point P due to current element depends the factors as stated below:
1. dB I
2. dB dl
3. dB sin
4. dB 1/r2
On combining these factors, we get
dB I dl sin /r2
dB = K I dl sin /r2
where, K is the constant of proportionality.
Important features of Biot-Savarts Law:
1. This law is applicable only to very small length conductor carrying current.
2. This law cannot be easily verified experimentally as the conductor of very small length
cannot be obtained practically.
3. This

law is analogous to Coulombs

Law in electrostatics.

4. dB is perpendicular to both dl and r .
5. If = 0, i.e. the point P lies on the conductor itself, then dB = K I l sin /r2
dB = 0 (sin = 0). Thus, there is no magnetic field induction at any point on the conductor.
6. If = 90 dB is maximum. Then, dB = K I l sin /r2.
A magnetic field at the centre of the circular coil carrying current:
Consider a circular coil of radius r with centre O, lying with its plane in the plane of
paper. Let I be the current flowing in the circular coil in a particular direction (Fig. 1.29).
Fig. 1.29: Magnetic field at the centre of circular coil carrying current
Suppose the circular coil is made up of a large number of current elements each of
length dl.
According to Biot-Savarts Law, the magnetic field at the centre of the circular coil due
to the current element dl is given by:

(dl r)

dB = K I _____________
r3

o
K = _____
4

where r is the position vector of point O from the current element.
The magnetic lines of force due to circular coil carrying current are perpendicular to the
plane of the wire loop and are circular near the wire and practically straight near the centre
of the wire loop. If the radius of the current loop is very large, the magnetic field near the
centre of the current loop is almost uniform (Fig. 1.30). The magnetic field at the centre of
circular current loop is given by Right hand palm rule.
Right hand palm rule: According to this rule, if we hold the thumb of right hand mutually
perpendicular to the grip of the fingers such that the curvature of the finger represents
the direction of current in the wire loop, then the thumb of the right hand will point in a
direction of magnetic field near the centre of the current loop.
Magnetic field due to a straight conductor carrying current:
Consider a long straight conductor XY lying in a plane of paper carrying current I in
the direction X to Y (Fig. 1.31).
Let P be a point at a perpendicular distance from the straight conductor. Clearly, PC = a.

Consider a small current element of length dl of the straight conductor at O. Let r be the
Fig. 1.30: Magnetic field near the centre of current loop of larger radius
Fig. 1.31: Magnetic field due to a straight conductor carrying current

position vector of P with respect to current element and be the angle between dl and r
and CO = l.
According to Biot-Savarts law, the magnetic field induction, i.e. magnetic flux density
at a point P due to current element dl is given by
dB = K I (dl r/r3)
0 I
or dB = ______ (dl sin /r2)
4

In right angled triangle POC, + = 90
0 I
dB = ______ cos d
4 a

The direction of dB, according to right hand thumb rule, will be perpendicular to the
plane of paper and directed inwards. As all the current elements of the conductor will also
produce magnetic field in the same direction, therefore, the total magnetic field at point P
due to current through the whole straight conductor XY can be obtained.
0 I
dB = ______ (sin 1 + sin 2)
4 a

Direction of magnetic field: The magnetic lines of force due to straight conductor
carrying current are in the form of concentric circles with the conductor as centre, lying in
a plane perpendicular to the straight conductor. The direction of magnetic lines of force is
anticlockwise, if the current flows from A to B in the straight conductor and is clockwise if
the current flows from B to A in the straight conductor (Fig. 1.32).
The direction of magnetic lines of force can be given by right hand thumb rule or
Maxwells cork screw rule.
Right hand thumb rule: According to this rule, if we imagine the linear conductor to be
held in the grip of the right hand so that the thumb points in the direction of current, then
the curvature of the fingers around the conductor will represent the direction of magnetic
lines of force (Fig. 1.33).
Fig. 1.32: Direction of magnetic lines of force
Fig. 1.33: Right hand thumb rule

Maxwells cork screw rule: According to this rule, if we imagine a right handed screw
placed along the current carrying linear conductor, be rotated such that the screw moves in
a direction of flow of current, then the direction of rotation of the thumb gives the direction
of magnetic lines of force (Fig. 1.34).
Fig. 1.34: Maxwells cork screw rule
Amperes circuital

law: Amperes circuital law states that the line integral of magnetic
field induction B around any closed path in vacuum is equal to 0 times the total current
threading the closed path, i.e.

B.dl = 0 I
This is independent of the size and shape of the closed curve enclosing a current.
Lorentz force: The force experienced by a charged particle moving in space where both
electric and magnetic fields exist is called Lorentz force.
Force due to electric field: when a charged particle carrying charge +q is subjected to an
electric field of strength E, it experiences a force given by

F = qE

Whose direction is the same as that of E.
Force due to magnetic field: If the charged particle is moving in a magnetic field B, with a

velocity v it experiences a force given by

Fm = q (v B)

The direction

of this force is in the direction of v B, i.e. perpendicular to the plane

containing v and B and is directed as given by Right hand screw rule.
Due to both the electric and magnetic fields, the total force experienced by the charged
particle will be given by

F = Fe + F m = qE + q(v B)

= q (E + v B)
This is called Lorentz force.
Moving coil Galvanometer

Moving coil galvanometer is an instrument used for detection and measurement of small
electric currents (Fig. 1.35).
Fig. 1.35: Moving coil galvanometer
Principle: Its working is based on the fact that when a current carrying coil is placed in
a magnetic field, it experiences a torque. It means, the deflection produced is proportional
to the current flowing through the galvanometer.
Current sensitivity of a galvanometer is defined as the deflection produced in the
galvanometer, when a unit current flows through it.
Voltage sensitivity of a galvanometer is defined as the deflection produced in the galva-
nometer when a unit voltage is applied across the two terminals of the galvanometer.
Conditions for a Sensitive Galvanometer

A galvanometer is said to be very sensitive if it shows large deflection even when a small
current is passed through it.
From the theory of galvanometer
= nBAI/k
For a given value of I, will be large if nBA/k is large. It is so if
a. n is large
b. B is large
c. A is large
d. k is small
a. The value of n cannot be increased beyond a certain limit because it results in an
increase of the resistance of the galvanometer and also makes the galvanometer bulky.
This tends to decrease the sensitivity. Hence, n cannot be increased beyond a certain
limit.
b. The value of B can be increased by using a strong horse shoe magnet.

c. The value of A cannot be increased beyond a certain limit because in that case the coil
will not be in a uniform magnetic field. Moreover, it will make the galvanometer bulky
and unmanageable.
d. The value of k can be decreased. The value of k depends upon the nature of the material
used as suspension strip. The value of k is very small for quartz or phosphor bronze.
That is why, in sensitive galvanometer, quartz or phosphor bronze is used as a suspen-
sion strip.
Shunt: Shunt is a low resistance connected in parallel with the galvanometer or ammeter.
It protects the galvanometer or ammeter from the strong currents.
If the current flowing in a circuit is strong, a galvanometer or ammeter cannot be put
directly in it because the instrument may be damaged. To overcome this difficulty, a low
resistance (i.e. shunt) is connected in parallel with the instrument. Then a major portion of
the current passes through this low resistance (i.e. shunt) and only a small portion passes
through the instrument. Due to it the galvanometer or ammeter remains same (Fig. 1.36).
Fig. 1.36: Shunt
Uses of Shunt
1. A shunt is used to protect the galvanometer from the strong currents.
2. A shunt is used for converting a galvanometer into an ammeter.
3. A shunt may be used for increasing the range of ammeter.
Ammeter: An ammeter is a low resistance galvanometer. It is used to measure the current in
a circuit in amperes. A galvanometer can be converted into an ammeter by using a low resis-
tance wire in parallel with the galvanometer (Fig. 1.37). The resistance of the wire (called the
shunt wire) depends upon the range of the ammeter. As the shunt resistance is small, the
combined resistance of the galvanometer and the shunt is very low and hence ammeter has
a much lower resistance than galvanometer. An ideal ammeter has zero resistance.
Voltmeter: A voltmeter is a high resistance galvanometer. It is used to measure the poten-
tial difference between two points of a circuit in volt. A galvanometer can be converted
into a voltmeter by using a high resistance in series with the galvanometer. The value of
the resistance depends upon the range of the voltmeter. For voltmeter, a high resistance R
is connected in series with the galvanometer, therefore, the resistance of voltmeter is very
large as compared to that of galvanometer. The resistance of an ideal voltmeter is infinity
(Fig. 1.38).
Fig. 1.37: Ammeter
Fig. 1.38: Voltmeter
Magnets and Earth Magnetism

A Greek Philosopher, Thales of Melitus had observed as long back as 600 BC that a
naturally occurring ore of iron attracted small pieces of iron toward it. This ore was found
in the district of Magnesia in Asia Minor in Greece. Hence, the ore was named magnetite.
The phenomenon of attraction of small bits of iron, steel, cobalt, nickel, etc. toward the ore
was called magnetism. The iron ore showing this effect was called a natural magnet.
The Chinese discovered that a piece of magnetite, when suspended freely, always
points out roughly in the North-South direction. Thus, a natural magnet has attractive
and directive properties. A magnetic compass based on directive property of magnets was
used by navigators to find their way in steering the ships.
That is why, magnetite was called the load stone in the sense of leading stone.
The natural magnets have often irregular shape and they are weak. It is found that a
piece of iron or steel can acquire magnetic properties, on rubbing with a magnet. Such
magnets made out of iron and steel are called artificial magnets. Artificial magnets can
have desired shape and desired strength. A bar magnet, a horse shoe magnet, magnetic
needle, compass needle, etc. all are artificial magnets.
Basic Properties of Magnets

Following are some basic properties of magnets:
1. A magnet attracts magnetic substances like iron, steel, cobalt, nickel toward it. When a
magnet is put in a heap of iron fillings, they cling to the magnet. The attraction appears
to be maximum at the ends of the magnet (Fig. 1.39). These ends are called poles of the
magnet.
Fig. 1.39: Attraction by the magnet (maximum at poles)
Fig. 1.40: A suspended magnet
2. When a magnet is suspended freely with the help of a unspun thread, it comes to rest
along the North-South direction. If it is turned from this direction and left, it again
returns to this direction. The pole which points toward the geographic north is called
North-pole and the pole which points toward geographic south is called South-pole
(Fig. 1.40).
It should be clearly understood that poles exist always in pairs; two poles of a
magnet are always of equal strength. Further, poles N and S are situated a little inwards
from the geometrical ends A and B of the magnet. The magnetic length (NS) of magnet
is roughly 6/7 of its geometric length (AB). We represent NS by 2l (and not l), this is
done for simplification of calculations.
The straight line passing through North-and-South poles of a magnet, is called
axial line of the magnet. The line passing through centre of a magnet in a direction
perpendicular to the length of the magnet is called equatorial line of the magnet.
The straight line joining north and south poles of a freely suspended magnet
represents magnetic N-S direction. A vertical plane passing through N-S line of a freely
suspended magnet is called magnetic meridian.
3. Like poles repel each other and unlike poles attract each other. To show this, we suspend
a bar magnet with the help of a thread. When we bring N pole of another magnet near
the N pole of suspended magnet, we observe repulsion. Similarly, South-pole of one
magnet repels South-pole of the other. However, when S pole of one is brought near N
pole of suspended magnet, there is attraction (Fig. 1.41).
4. The force of attraction or repulsion F between two magnetic poles of strengths m1 and
m2 separated by a distance r is directly proportional to the product of pole strengths
and inversely proportional to the square of the distance between their centers, i.e.
Fig. 1.41: Repulsion and attraction by magnets
F m1 m2/r2
F = K m1 m2/r2
Where K is magnetic force constant
In SI units, K = 0/4
= 107 Wb A1 m1
where 0 is absolute magnetic permeability of free space (air/vacuum).
0 m1 m2
F = _______________
4 r2
This is called Coulombs law of magnetic force. However in cgs system, the value of
K = 1.
5. The magnetic poles always exist in pairs, i.e. magnetic monopoles do not exist. In an
attempt to separate the magnetic poles, if we break a magnet, we find new poles formed
at the broken ends. If the two pieces are broken again, we find the broken ends contain
new poles. Thus each piece, howsoever small, is a complete magnet in itself. Even if
a magnet is broken into molecules, each molecule shall be a complete magnet. Note
that pole strength (m) of each piece broken lengthwise, remains unchanged, although
dipole moment M = m 2l goes on decreasing, with decreasing length.
Atomic/Molecular Theory of Magnetism

The molecular theory of magnetism was given by Weber and modified later by Ewing.
According to this theory:
1. Every molecule of a magnetic substance (whether magnetized or not) is a complete in
itself, having a north pole and a south pole of equal strength.
2. In an unmagnetized substance, the molecular magnets are randomly oriented such that
they form closed chains (Fig. 1.42). The North-pole of one molecular magnet cancels the
effect of South-pole of the other so that the resultant magnetism of the unmagnetized
specimen is zero.
3. On magnetizing the substance, the molecular magnets are realigned so that North-
poles of all molecular magnets point in one direction and South-poles of all molecular
magnets point in opposite direction (Fig. 1.43).
Fig. 1.42: Unmagnetized magnet Fig. 1.43: Magnetized magnet
The extent of magnetization of the specimen is the extent of realignment of the

molecular magnets.
4. When all the molecular magnets are fully aligned, the substance is said to be saturated
with magnetism.
5. At all stages, the strengths of the two poles developed will always be equal.
6. On heating the magnetized specimen, molecular magnets acquire some kinetic energy.
Some of the molecules may get back to the closed chain arrangement. That is why
magnetism of the specimen would reduce on heating.
Magnetic lines of force: The concept of magnetic lines of force or simply the field lines
was developed to visualize the effect of the magnetic field. The magnetic field lines
represent the magnetic field in the same way as the electric field lines represent an
electric field.
The magnetic lines of force do not exist in reality. They are only hypothetical lines,
which enable us to understand certain phenomena in magnetism. To draw these lines,
we have to take a test object which is a magnetic dipole such as a small compass needle.
If we imagine a number of small compass needles around a magnet, each compass
needle experiences a torque due to the field of the magnet. The torque acting on a compass
needle aligns it in the direction of the magnetic field. The path along which the compass
needles are aligned is known as magnetic lines of force. It should be clearly understood
that tangent to a field line at any point P gives the direction of magnetic field B at that point
(Fig. 1.44).
Properties of magnetic lines: Following are some of the important properties of the
magnetic lines of force:
1. Magnetic lines of force are closed continuous curves; we may imagine them to be
extending through the body of the magnet.
2. Outside the body of the magnet, the direction of magnetic lines of force, is from North-
pole to South-pole (Fig. 1.45).
3. The tangent to magnetic lines of force at any point gives the direction of magnetic field
at that point.
4. No two magnetic lines of force can intersect each other (Fig. 1.46).
5. Magnetic lines of force contract longitudinally and they dilate laterally.
Fig. 1.44: Tangent to a magnetic line of Fig. 1.45: Magnetic line of force
force
Fig. 1.46: Direction of magnetic lines of force
6. Crowding of magnetic lines of force represents stronger magnetic field and vice-versa
(Fig. 1.47).
It should be clearly understood that there is one fundamental difference between
electricity and magnetism. Where as in electricity, an isolated charge can exist, in magnetism,
an isolated pole does not exist. The simplest magnetic struc
ture that can exist is only a
magnetic dipole, characterized by magnetic dipole moment M. Thus for
mapping magnetic
field, the simplest test object is a dipole. That is why in the definition of B above,

we have used
the word hypothetical

isolated north pole. However, this definition of B (corres
ponding to
definition of E ) enables us to simplify some calculations.
Thus, magnetic dipole is characterized by a vector M in place of a scalar charge q in
electricity. We shall show that in an external magnetic field, the dipole experiences a torque
(unlike the force experienced by charge q in electric field). The effect of torque is to align
the dipole along the external magnetic field. The directive property of a magnet is attri
buted to the torque acting on the magnetic dipole due to earths magnetic field.
Fig. 1.47: Crowding of magnetic lines of force

Each electric line of force starts from a positive charge and ends at a negative charge.
It should be clearly understood that the electric lines are discontinuous only in the sense
that no such lines exist inside a charged body. However, from a positively charged body
to a negatively charged body, there is no discontinuity in the electric lines of force. In
magnetism, as there are no monopoles, therefore, the magnetic field lines will be along
closed loops with no starting or ending. The magnetic lines of force would pass through
body of the magnet. At very far off points, the field lines due to an electric dipole and a
magnetic dipole will appear identical.
Remember that electric lines of force are discontinuous, whereas magnetic lines of force
are closed continuous curves.
Magnetic dipole: A magnetic dipole consists of two unlike poles of equal strength and
separated by a small distance. For example, a bar magnet, a compass needle, etc. are
magnetic dipoles. An atom of a magnetic material behaves as a dipole due to electrons
revolving around the nucleus. Magnetic dipole moment is defined as the product of pole
strength and the distance between the two poles. This distance between the poles is called
magnetic length and is represented by 2l. If m is the strength of each pole, then magnetic
dipole moment (M) is
M = m (2l)
Magnetic dipole moment is a vector quantity directed from South-to-North-pole. The
SI units of M are joule/tesla or ampere-metre2 (Fig. 1.48).
The direction of magnetic moment (M) is from south to north. This corresponds to the
electric dipole moment (p) of an electric dipole from negative charge to positive charge.
Gausss theorem (or Gausss law) in magnetism: According to Gausss theorem, the
surface integral of electrostatic field E over a closed surface S is equal to 1/o times the total
charge q inside the surface, where o is absolute electrical permittivity of free space, i.e.

E . ds = q/
Fig. 1.48: Magnetic dipole

If an electric dipole was enclosed by the surface, equal and opposite charges in the
dipole add up to zero. Therefore, surface integral of electric field of a dipole over a closed
surface enclosing an electric dipole is zero, i.e.

E. ds = 0
Whereas, electric field can be produced by isolated charge, the magnetic field is
produced only by a magnetic dipole. This is because isolated magnetic poles do not exist.
Hence magnetic analogue equation is as follows:

B . ds = 0
That is surface integral of magnetic field over a surface (closed or open) is always zero,
i.e. the net magnetic flux B through any surface S is always zero. This is called Gausss law
in magnetism. In terms of magnetic field lines, the law means that there are as many lines
entering S, as are leaving it (Fig. 1.49).
Magnetic field of earth: Sir William Gilbert was the first to suggest in the year 1600, that
earth itself is a huge magnet. His statement was based on the following evidence:
1. A magnet suspended from a thread and free to rotate in a horizontal plane comes to
rest along the north-south direction. On disturbing, the magnet returns quickly to its
north-south direction again this is as if huge bar magnet lies along the diameter of the
earth. The North pole of this fictitious magnet must be toward geographic south so as
to attract South pole of the suspended magnet and vice-versa.
Fig. 1.49: Magnetic field lines

2. When a soft iron piece is buried under the surface of earth in the north-south direction,
it is found to acquire the properties of a magnet after sometime.
3. When we draw field lines of a magnet, we come across neutral points. At these points,
magnetic field due to the magnet is neutralized or cancelled exactly by the magnetic field
of earth. If earth had no magnetism of its own, we would never observe neutral points.
The branch of physics which deals with the study of magnetism of earth is called terrestrial
magnetism or geomagnetism.
It has been established that earths magnetic field is fairly uniform. The strength of this
field is approximately 10-4 tesla or 1 gauss. The field is not confined only to earths surface.
It extends upto a height nearly 5 times the radius of the earth.
Cause of earths magnetism: The exact cause of earths magnetism is not yet known.
However, some important postulates in this respect are as follows:
1. The earths magnetism may be due to molten charged metallic fluid in the core of earth.
The radius of this core is about 3500 km with the rotation of earth, the fluid also rotates
resulting in the development of currents in the core of earth. These currents magnetize
the earth.
2. According to Prof Brackett, earths magnetism may be due to rotation of earth about
its axis. This is because every substance is made of charged particles (protons and
electrons). Therefore, a substance rotating about an axis is equivalent to circulating
currents, which are responsible for its magnetization.
3. In the outer layers of earths atmosphere, gases are in the ionised state, primarily on
account of cosmic rays. As earth rotates, strong electric currents are set up due to move-
ment of (charged) ions. These currents might be magnetizing the earth.
Electromagnetic induction
Michael Faraday in UK and Joseph Henry in USA observed that an emf is produced
across the ends of a conductor when the number of magnetic lines of force associated with
the conductor changes. The emf lasts so long as this change continues. This phenomenon
of generating an emf by changing the number of magnetic lines of force associated with
the conductor is called electromagnetic induction (EMI). The emf so developed is called
induced emf. If the conductor is in the form of a closed circuit, a current flows in the circuit.
This is called induced current.
The phenomenon of EMI is the basis of power generators, dynamos, transformers, etc.
and hence it is important.
Magnetic flux: The magnetic flux through any surface held in a magnetic field is measured
by the total number of magnetic lines of force crossing the surface. The unit of magnetic flux
is weber (Wb). One weber is the amount of magnetic flux over an area of 1 m2 held uniform
to a uniform magnetic field of one tesla. Also, magnetic flux is a scalar quantity.
Faradays Experiments
Experiment 1. Figure 1.50 shows a circular insulated wire of one or more turns connected
to a sensitive galvanometer G. North-South is a bar magnet which can be moved with
respect to the coil. Faraday observed the following:
Fig. 1.50: EMF induced in a coil due to moving magnet
i. Whenever there is a relative motion between the coil and the magnet, the galvanometer
shows a sudden deflection. This deflection indicates that current is induced in the
coil.
ii. The deflection is temporary. It lasts so long as relative motion between the coil and
the magnet continues.
iii. The deflection is more when the magnet is moved faster and less when the magnet is
moved slowly.
iv. The direction of deflection is reversed when same pole of magnet is moved in the
opposite direction or opposite pole of magnet is moved in the same direction.
The motion of the magnet implies that the number of magnetic lines of force threading
the coil is changing.
Experiment II. Figure 1.55 shows the experimental set up. Coil 1 is connected to a battery,
a rheostat and a key K. Coil 2 is connected to a sensitive galvanometer G and is held close
to coil 1.
When we press K, galvanometer G in coil 2 shows a sudden temporary deflection. This
indicates that current is induced in coil 2. This is because current in coil 1 increases from
zero to a certain steady value increasing the magnetic field of coil 1 and hence the number
of magnetic lines of force entering coil 2. Their direction is shown in the Figure 1.51.
On releasing K, galvanometer shows a sudden temporary deflection in the opposite
direction. This is because on releasing K, current in coil 1 decreases from maximum to zero
value, decreasing thereby the magnetic field of coil 1 and hence the number of magnetic
lines of force entering coil 2.
Thus, the results of the two experiments are identical.
Note: In both the experiments discussed above, we find that induced emf appears in a coil
whenever the amount of magnetic flux linked with the coil changes. Hence we conclude that
Fig. 1.51: EMG induced in a coil due to current carrying coil

the cause of emf induced in a coil is change in magnetic flux linked with the coil. It should
be clearly understood that mere presence of magnetic flux is not enough. The amount of
magnetic flux linked with a coil must change in order to produce any induced emf in the coil.
Faradays laws of electromagnetic induction: Following are the laws of electromagnetic
induction as given by Faraday. Both the laws follow from Faradays experiments discussed
above.
First law: Whenever the amount of magnetic flux linked with a circuit changes, an emf is
induced in the circuit. The induced emf lasts so long as the change in magnetic flux continues.
Second law: The magnitude of emf induced in a circuit is directly proportional to the rate
of change of magnetic flux linked with a circuit.
Explanation
First law: In Faradays experiment, when magnet is moved toward the coil, number of
magnetic lines of force linked with the coil increases, i.e. magnetic flux increases. When the
magnet is moved away, the magnetic flux linked with the coil decreases. In both the cases,
galvanometer shows deflection indicating that emf is induced in the coil.
When there is no relative motion between the magnet and the coil, magnetic flux linked
with the coil remains constant. That is why galvanometer shows no deflection. Thus,
induced emf is produced when magnetic flux changes and induced emf continues so long
as the change in magnetic flux continues. This is first law. The same results follow from
Faradays second experiment.
Second law: In Faradays experiment, when magnet is moved faster, the magnetic flux
linked with the coil changes at a faster. Therefore, galvanometer deflection is more.
However, when the magnet is moved slowly, rate of change of magnetic flux is smaller.
Therefore, galvanometer deflection is smaller. Hence magnitude of emf induced varies
directly as the rate of change of magnetic flux linked with the coil. This is second law.
If it is amount of magnetic flux linked with the coil at any time and is the magnetic flux
linked with the coil after t second then
Rate of change of magnetic flux = According to Faradays second law, induced emf
2 1
e _________

t
K (2 1)
or e = _____________

t
where, K is a constant of proportionality.
As K = 1 (in all systems of units)
2 1
E = _________
t
I f d is small change in magnetic flux in a small time dt, then
d
E = _______
dt
Negative sign is taken because induced emf always opposes any change in magnetic
flux associated with the circuit.
Lenzs law: This law gives us the direction of current in a circuit. According to this law,
the induced current will appear in such a direction that it opposes the change (in magnetic
flux) responsible for its production.
The law refers to induced currents, which means that it applies only to closed circuits.
When we push the magnet toward the coil (or the loop toward the magnet), an induced
current appears. In terms of Lenzs law, induced current will oppose the push when face
of the loop toward the magnet becomes a north pole. Therefore, induced current will be
anticlockwise, as we see along the magnet toward the loop.
If we pull the magnet away from the coil, the induced current will oppose the pull by
creating a south pole on the face of the loop toward the magnet. Therefore, induced current
will be clockwise.
The agent that moves the magnet, either toward the coil or away from it, will always
experience a resisting force and will thus be required to do the work.
Experimental verification of Lenzs law (Fig. 1.52): A coil of a few turns is connected to a
cell C and a sensitive galvanometer G through a two way key 1, 2, 3.
Put in the plug of key between 1 and 2. Cell sends current through the coil. At the upper
face of the coil, the current is anticlockwise, which would produce north pole on this face.
Suppose the galvanometer deflection is to the right. Obviously, if galvanometer deflection
were to the left, current would be clockwise at the upper face, which would behave as
south pole.
Remove the plug of key from 1 and 2. Insert the plug of key between 2 and 3. Now,
move N-pole of a bar magnet toward the coil. The galvanometer shows a sudden deflection
to the right indicating that current induced in the coil is anticlockwise and upper end of the
coil behaves as north. It opposes the inward motion of N-pole of the bar magnet, which is
the cause of induced current.
Fig. 1.52: Experimental set up for verifying Lenzs law

Similarly, when N-pole of the bar magnet is moved away from the coil, the galvanometer
shows a sudden deflection to the left, indicating that current induced in the coil is clockwise
and upper end of the coil behaves as south. It opposes the outward motion of N-pole of the
bar magnet, i.e. cause of induced emf is opposed.
Exactly similar results follow when S-pole of magnet is moved instead of N-pole.
Hence, induced current always opposes the change which produces it. This verifies
Lenzs law.
Lenzs law and energy conservation: Lenzs law is in accordance with the law of conservation
of energy.
For example, in the experimental verification of Lenzs law, when N-pole of magnet is
moved toward the coil, the upper face of the coil acquires north polarity. Therefore, work
has to be done against the force of repulsion, in bringing the magnet closer to the coil.
Similarly, when N-pole of magnet is moved away, south polarity develops on the upper
face of the coil. Therefore, work has to be done against the force of attraction, in taking the
magnet away from the coil.
It is this mechanical work done in moving the magnet with respect to the coil that changes
into electrical energy producing induced current. Thus, energy is being transformed only.
When we do not move the magnet, work done is zero. Therefore, induced current is
also not produced.
Hence Lenzs law obeys the principle of energy conservation.
Conversely, Lenzs law can be treated as a consequence of the principle of energy
conservation.
Flemings right hand rule: Flemings right hand rule also gives the direction of induced
emf/current, in a conductor moving in a magnetic field. According to this rule, if we stretch
the first finger, central finger and thumb of our right hand in mutually perpendicular
directions such that first finger points along the direction of the field and thumb is along
the direction of motion of the conductor, then the central finger would give us the direction
of induced current (Fig. 1.53).
The direction of induced current given by Lenzs law and Flemings right hand rule is
the same.
Fig. 1.53: Flemings right hand rule

Eddy currents: Eddy currents are the currents induced in the body of the conductor when
the amount of magnetic flux linked with the conductor changes. These were discovered by
Foucault in the year 1895 and hence they are also called Foucault currents.
The magnitude of eddy current is
i = induced emf/resistance = e/R
but e = d/dt
_____________ d/dt
i =
R
The direction of eddy currents is given by Lenzs law or Flemings right hand rule.
Note: Eddy currents are basically the currents induced in the body of a conductor due to
change in magnetic flux linked with the conductor.
Experimental Demonstration
Experiment 1: Hold a light metallic disc D atop the cross-section of an electromagnet
connected to a source of a.c. (Figure 1.54). When a.c. is switched on, the disc is thrown up
into the air.
This is due to eddy currents developed in the disc. As current through the solenoid
increases, the magnetic flux along the axis of the solenoid increases. Therefore, magnetic
flux linked with the disc increases. Induced currents or eddy currents develop in the disc
and magnetize it. If upper end of solenoid initially acquires north polarity, the lower face of
disc also acquires north polarity in accordance with the Lenzs law. The force of repulsion
between the two throws the disc up in the air.
Experiment 2: Suspend a flat metallic plate between pole pieces N and S of an electromagnet
(Fig. 1.55).
Fig.1.54: Eddy currents on a disc Fig. 1.55: Eddy currents on a flat metallic plate
When the magnetic field is off, the metallic plate disturbed once from its equilibrium
position and left, oscillates freely for a longer time. But when the electromagnet is switched
on, the vibrations of the plate are damped. This is because of eddy currents developed in
the vibrating plate.
In the normal position of rest of the plate, magnetic flux linked with the plate is
maximum. When it is displaced toward any one extreme position, area of plate in the field
decreases. Therefore, magnetic flux through the plate decreases. Eddy currents develop in
the plate which, according to Lenzs law, opposes the motion of the plate toward extreme
position. Similarly, when plate returns from extreme position to mean position, area of
plate in the field increases, magnetic flux linked with the plate increases. Eddy currents are
developed which oppose the motion of the plate toward the mean position.
In either case, vibrations of the plate are damped.
Figure 1.56 shows the same metallic plate with slots cut in it. When such a plate is
made to oscillate in the magnetic field, the damping effect is there, but it is much smaller
compared to the case when no slots were cut.
This means eddy currents are reduced. This is because closed loop of a given area now
has a much longer path. As longer path means more resistance, eddy currents will reduce.
We can only minimize eddy currents but cannot reduce such currents to zero.
Fig. 1.56: Eddy currents on metallic plate with slots
Applications of Eddy Currents

Eddy currents are useful in many ways:
Some of the applications of eddy currents are:
a. Electromagnetic damping: This is used in designing dead beat galvanometers. When
a steady current is passed through the coil of a galvanometer, it is deflected. Normally,
the coil oscillates about its equilibrium position for some time before coming to rest.
To avoid delay due to these oscillations, the coil is wound over a metallic frame. As the
coil is deflected, eddy currents set up in the metallic frame oppose its motion.
Therefore, the coil attains its equilibrium position almost instantly. Thus, the motion of
coil is damped. This is called electromagnetic damping.
b. Induction furnace: It makes use of the heating effect of eddy currents. The substance to
be heated/melted is placed in a high frequency magnetic field. The large eddy currents
developed in the substance produce so much heat that it melts. Such an arrangement
is called induction furnace. It is used for extracting a metal from its ore and also in the
preparation of certain alloys.
c. Electromagnetic brakes: They are used in controlling the speed of electric trains. A
strong magnetic field is applied to a metallic drum rotating with the axle connecting
the wheels. Large eddy currents set up in the rotating drum oppose the motion of the
drum and tend to stop the train.
d. Induction motor: A induction motor or a.c. motor is another important application
of eddy currents. A rotating magnetic field produces strong eddy currents in a rotor,
which starts rotating in the direction of the rotating magnetic field.
e. Speedometers: In speedometers of automobiles and energy meters.
f. Eddy currents: They are also used in diathermy, i.e. in deep heat treatment of the
human body.
Some of the undesirable effects of eddy currents are:
i. They oppose the relative motion.
ii. They involve loss of energy in the form of heat.
iii. The excessive heating may break the insulation in the appliances and reduce
their life.
To minimize the eddy currents, the metal core to be used in an appliance like dynamo,
transformer, choke coil, etc. is taken in the form of thin sheets. Each sheet is electrically
insulated from the other by insulating varnish. Such a core is called a laminated core. The
planes of these sheets are arranged parallel to the magnetic flux.
Large resistance between the thin sheets confines the eddy currents to the individual
sheets. Hence, the eddy currents are reduced to a large extent.
Self Induction
Self induction is the property of a coil by
virtue of which, the coil opposes any change
in the strength of current flowing through it
by inducing an emf in itself. For this reason,
self induction is also called the inertia of
electricity.
Suppose there is a coil connected to a cell
through a tap key K (Fig. 1.57).
On pressing K, current through the coil
increases from zero to a certain maximum
value. It takes some time. During this time
(of make M), current through the coil is Fig. 1.57: Self induction
increasing, magnetic flux linked with the coil
is increasing. Therefore, a current is induced in the coil. According to Lenzs law, the induced
current at make will oppose the growth of current in the coil, by flowing in a direction
opposite to the direction of the cell current.
On releasing K, current through the coil decreases from maximum to zero value. It takes
some time. During the time (of break B), current through the coil is decreasing. Therefore,
magnetic flux linked with the coil is decreasing. A current is induced in the coil. According
to Lenzs law, the induced current at break will oppose the decay of current in the coil, by
flowing in the direction of the cell current, so as to prolong it.
Coefficient of self induction (L) of a coil is equal to the emf induced in the coil when rate
of change of current through the coil is unity.
The SI unit of L is henry. Self inductance of a coil is said to be one henry, when a current
change at the rate of one ampere/sec through the coil induces an emf of one volt in the coil.
Mutual Induction
Mutual induction is the property of two coils
by virtue of which each opposes any change
in the strength of current flowing through the
other by developing an induced emf.
Suppose there are two coils P and S which
are held closely. P is connected to a cell through
a key K. S is connected to a sensitive galvanom-
eter G (Fig. 1.58).
On pressing or releasing K, galvanometer
shows a temporary deflection. This is due to
mutual induction as detailed below:
On pressing K, current in P increases from
zero to maximum value. It takes some time.
During this time (of make M), current in P is
increasing. Therefore, magnetic flux linked
with P is increasing. As S is close by, magnetic
Fig.1.58: Mutual induction
flux associated with S also increases. An emf
is induced in S, according to Lenzs law, the
induced current in S would oppose increase in current in P by flowing in a direction
opposite to the cell current in P.
On releasing K, current in P decreases from maximum to zero value. It takes some time.
During this time (of break B), current in P is decreasing. Therefore, magnetic flux linked
with P is decreasing. As S is close by, magnetic flux associated with S also decreases. An
emf is induced in S. According to Lenzs law, the induced current in S during break flows
in the direction of the cell current in P so as to oppose the decrease in current in P, i.e. it
prolongs the decay of current.
Coefficient of mutual inductance of two coils is numerically equal to the amount of
magnetic flux linked with one coil when unit current flows through the neighboring coil.
Coefficient of mutual induction (M) of two coils is equal to the emf induced in one coil
when rate of change of current through the other coil is unity.
The SI unit of M is henry. Coefficient of mutual inductance of two coils is said to be one
henry, when a current change at the rate of one ampere/sec in one coil induces an emf of
one volt in the other coil.
The mutual inductance of two coils depends on:
i. geometry of two coils, i.e. size of coils, their shape, number of turns, nature of
material on which two coils are wound.
ii. distance between two coils.
iii. relative placement of two coils (i.e. orientation of the coils).
Note: In self induction, change in strength of current in a coil is opposed by the coil itself
by inducing an emf in itself. However, in mutual induction, one coil opposes any change in
the strength of current in the neighboring coil. It should be clearly understood that mutual
induction is over and the self induction of each coil, due to change in magnetic flux in both.
AC Generator/Dynamo
An a.c. generator/dynamo is a machine which produces alternating current energy from
mechanical energy. It is one of the most important applications of the phenomenon of
electromagnetic induction. The generator was designed by Yugoslav scientist, Nikola Tesla.
It is an alternator converting one form of energy into another.
Principle: An a.c. generator/dynamo is based on the phenomenon of electromagnetic
induction, i.e. whenever amount of magnetic flux linked with the coil changes, an emf is
induced in the coil. It lasts so long as the magnetic flux through the coil continues. The
direction of current induced is given by Flemings right hand rule.
Multiphase AC Generator
a. Two phase a.c. generator: In this
generator, there are two armature
coils held at 90 to each other. Each
coil has its own pair of slip rings
and brushes. When this pair of coils
is rotated in magnetic field, emf
is induced in each coil. When emf
induced in one coil is maximum, it is
minimum in the other coil and vice- Fig. 1.59: Two phase a.c.
versa. Thus, the emfs induced in the
two coils differ in phase by 90. This
is called two phase a.c (Fig. 1.59).
b. Three phase a.c. generator: In this
generator, there are three armature
coils equally inclined to one another
at 60. Each coil has its own pair of
slip rings and brushes. When this
arrangement of coils is rotated in
magnetic field, emf is induced in
each coil. Thus we obtain three alter-
nating emfs differing in phase from Fig. 1.60: Three phase a.c.
one another by 60. This is called
three phase a.c (Fig. 1.60).
c. In general: When there are a number of separate coils, each having its own pair of slip
rings and brushes, the generator is called polyphase generator. The current produced
is called polyphase alternating current.
In actual practice one end of each coil is brought to a common point through shaft of
the generator. The line wire from this line is called Neutral line. Separate slip rings are
provided for other ends of different coils. The line wires from these rings (through these
brushes) are called phase lines.
It should be clearly understood that the principle of generator discussed here applies
to all the practical devices for the purpose ranging from portable generator to giant hydro-
electric and thermal power generators and even nuclear power generators.
In a hydroelectric power station, water is stored to a great height in a dam, from where it
falls on to giant turbines (popularly known as water wheels). These turbines are connected
to loops of wires in a.c. generator. Thus, kinetic energy of falling water is converted into
rotational energy of turbines, which leads to the production of electric energy by the
generator.
In a thermal power station, superheated steam is produced by boiling water using coal
or oil as fuel. The superheated steam pushes past the turbines and rotates them. This leads
to the production of electrical energy by the generator.
DC Generator/Dynamo
A d.c. generator/dynamo is device which is used for producing direct current energy from
mechanical energy.
The principle of d.c. generator is the same as that of a.c. generator.
Motor starter: A starter is a device which is used for starting a d.c. motor safely. Its function
is to introduce a suitable resistance in the circuit at the time of starting of the motor. This
resistance decreases gradually and reduces to zero when the motor runs at full speed.
Infact, resistance of armature of d.c. motor is kept low (to reduce the copper losses) and
when armature is stationary, there is no back emf. Therefore, when operating voltage is
applied, the current through armature coil may become so large (I = V/R) that the motor
may burn. A starter is needed to avoid this.
The Transformer
A transformer is an electric device which is used for changing the a.c. voltages.
A transformer which increases the a.c. voltages is called a step up transformer. A
transformer which decreases the a.c. voltages is called a step down transformer.
Principle: A transformer is based on the principle of mutual induction, i.e. whenever the
amount of magnetic flux linked with the coil changes, an emf is induced in the neighbouring
coil.
Construction: The transformer consists of two coils of insulated wire wound onto a
laminated soft-iron frame. The two coils may be wound on top of one another or on opposite
sides of the frame.
Working: An alternating current is passed through the primary coil and this sets up a
varying magnetic field which cuts the secondary coil. By electromagnetic induction, an
EMF is induced into the secondary circuit.
Step-up transformer: In this, the number of turns in the primary coil is less than that in
the secondary coil (Fig. 1.61).
The primary coil is made up of thick insulated copper wire, with less number of turns,
while the secondary coil is made up of thin insulated copper wire, with large number of
turns. It converts a low voltage at high current into high voltage at low current.
Step-down transformer: In this, the number of turns in the primary coil is more than that
in the secondary coil (Fig. 1.62).
The primary coil is made up of thin insulated copper wire with larger number of turns,
while the secondary coil is made up of thick copper wire with less number of turns. It
converts a high voltage at low current into low voltage at high current.
Fig. 1.61: Step up transformer Fig. 1.62: Step down transformer
Types of Transformers
1. Static transformer: It has been described above.
2. Variable transformer: This consists of a primary and a secondary coil and is made so
that one of them can be altered in length. The primary coil has a number of tappings
and a movable contact can be placed on any one of these by turning a knobs. There is
a step up voltage in the secondary coil. In this way, a very crude control of voltage is
obtained.
3. The autotransformer: It consists of a single coil of wire with four contact points coming from
it. It works on the principles of electromagnetic induction, but it has the disadvantage
that it allows only a small step up and does not render the current earth free.
Energy Losses in a Transformer

Following are the major sources of energy loss in a transformer:
1. Copper loss: It is the energy loss in the form of heat in the copper coils of the transformer.
This is due to Joule heating of conducting wires.
2. Iron loss: It is the energy loss in the form of heat in the iron core of the transformer. This is
due to formation of eddy currents in iron core. It is minimized by taking laminated cores.
3. Leakage of magnetic flux: It occurs in spite of best insulations. Therefore, rate of change
of magnetic flux linked with each turn of S1 S2 is less than the rate of change of magnetic
flux linked with each turn of P1 P2.
4. Hysteresis loss: This is the loss of energy due to repeated magnetization and demagne-
tization of the iron core when a.c. is fed to it.
5. Magnetostriction: That is humming noise of a transformer.
Therefore, output power in a transformer is roughly 90% of the input power.
Uses of Transformer
A transformer is used in almost all a.c. operations, e.g.
1. In voltage regulators of TV, refrigerator, computer, air conditioner, etc.
2. In the induction furnaces
3. A step down transformer is used for welding purposes.
4. In the transmission of a.c. over long distances.
Electromagnetic Waves
History of Electromagnetic Waves
Faraday from his experimental study of electromagnetic induction concluded that a
magnetic field changing with time at a point produces an electric field at that point. Maxwell
in 1865 from his theoretical study pointed out there is a great symmetry in nature, i.e.
an electric field changing with time at a point produces a magnetic field there. It means a
change in either field (electric or magnetic) with time produces the other field. This idea
led Maxwell to conclude that the variation in electric and magnetic field vectors perpen-
dicular to each other leads to the production of electromagnetic disturbances in space.
These disturbances have the properties of wave and can travel in space even without any
material medium. These waves are called electromagnetic waves.
According to Maxwell, the electromagnetic waves are those waves in which there are
sinusoidal variation of electric and magnetic field vectors at right angles to each other as
well as at right angles to the direction of wave propagation. Both these fields vary with
time and space and have the same frequency.
In Figure 1.63, the electric field vector (E) and magnetic field (B) are vibrating along Y
and Z directions and propagation of electromagnetic wave is shown in X-direction.
Maxwell also found that the electromagnetic wave should travel in free space (or
vacuum) also.
Maxwell also concluded that electromagnetic wave is transverse in nature and light is
electromagnetic wave.
Examples of electromagnetic waves are radiowaves, microwaves, infrared rays, light
waves, ultraviolet rays, X-rays and -rays.
Fig. 1.63: Electromagnetic waves

In 1888, Hertz confirmed experimentally the existence of electromagnetic waves. With

the help of his experiment, Hertz produced electromagnetic waves of wavelength about 6 m.
In 1894, an Indian Physicist Jagdish Chander Bose was able to produce electromagnetic
waves of wavelength ~ 5 to 25 mm but his experiment was confined to laboratory only.
In 1899, Guylielmo Marconi was the first to transmit electromagnetic waves up to a
few kilometers and established a wireless communication across the English Channel, a
distance of about 50 km.
Production of Electromagnetic Waves

We know that an electric charge at rest has electric field in the region around it, but no
magnetic field. A moving charge produces both the electric and magnetic fields. If a charge
is moving with a constant velocity (i.e. if current is not changing with time), the electric and
magnetic fields will not change with time, hence no electromagnetic wave can be produced.
But if the charge is moving with a non-zero acceleration (i.e. charge is accelerated) both
the magnetic field and electric fields will change with space and time, it then produces
electromagnetic wave. This shows that an accelerated charge emits electromagnetic waves.
In an atom, an electron while orbiting around the nucleus in a stable orbit, although
accelerating, does not emit electromagnetic waves. Electromagnetic waves are emitted
only when it falls from higher energy orbit to lower energy orbit.
Electromagnetic waves (i.e. X-rays) are also produced when fast moving electrons are
suddenly stopped by the metal target of high atomic number.
Important Facts About the Electromagnetic Waves

1. The electromagnetic waves are produced by accelerated or oscillated charge.
2. These waves do not require any material medium for propagation.
3. These waves travel in free space with a speed 3 108 m/s (i.e. speed of light).
4. The sinusoidal variation in both electric and magnetic field vectors (E and B) occurs
simultaneously. As a result, they attain the maxima and minima at the same place
and at the same time.
5. The directions of variation of electric and magnetic field vectors are perpendicular
to each other as well as perpendicular to the direction of propagation of waves.
Therefore, electromagnetic waves are transverse in nature like light waves.
6. The velocity of electromagnetic waves depends entirely on the electric and magnetic
properties of the medium in which these waves travel and is independent of the
amplitude of the field vectors.
7. The velocity of electromagnetic waves in dielectric is less than 3 108 m/s.
8. The energy in electromagnetic waves is equally divided between electric and
magnetic vectors.
9. The electric vector is responsible for the optical effects of an electromagnetic wave
and is called the light vector.
10. The electromagnetic waves being uncharged are not deflected by electric and
magnetic fields.
Electromagnetic Spectrum
Maxwell in 1865 predicted electromagnetic waves from theoretical considerations and
their existence was confirmed experimentally by Hertz in 1888.
Hertz experiment was based on the fact that an oscillating electric charge radiates
electromagnetic waves and these waves carry energy which is being supplied at the cost of
kinetic energy of the oscillating charge. The detailed study revealed that the electromagnetic
radiation is significant only if the distance to which the charge oscillates is comparable to
the wavelength of radiation.
After the experimental discovery of electromagnetic waves by Hertz, many other
electromagnetic waves were discovered by different ways of excitation.
The orderly distribution of electromagnetic radiations according to their wavelength or frequency
is called electromagnetic spectrum.
The electromagnetic spectrum has much wider range with wavelength variation of
~10-14 m to 6 106 m.
The whole electromagnetic spectrum has been classified into different parts or subparts
in order of increasing wavelength, according to their type of excitation. There is overlapping
S.No. Name Wavelength Frequency Source

range (m) range (Hz)
1. Gamma rays 6 1014 to 1 1011 5 1022 to 3 1019 Nuclear origin
2. X-rays 1 1011 to 3 108 3 1019 to 1 1016 Sudden declaration of

high energy electrons
3. Ultraviolet rays 6 1010 to 4 107 5 1017 to 8 1014 Excitation of atom, spark

and arc lamp
4. Visible light 4 107 to 8 107 8 1014 to 4 1014 Excitation of valence

electrons
5. Infrared 8 107 to 3 105 4 1014 to 1 1013 Excitation of atoms and

molecules
6. Heat radiations 105 to 101 3 1013 to 3 109 Hot bodies
7. Microwaves 103 to 0.3 3 1011 to 1 109 Oscillating current in

special vacuum tube
8. Ultra-high 1 101 to 1 3 109 to 3 108 Oscillating circuit

frequency
9. Very high radio 1 to 10 3 108 to 3 107 Oscillating circuit

frequency
10. Radio 10 to 104 3 107 to 3 104 Oscillating circuit

frequencies
11. Power 5 106 to 6 106 60 to 50 Weak radiations from AC

frequencies circuits
in certain parts of the spectrum, showing that the corresponding radiations can be produced
by two methods. It may be noted that the physical properties of electromagnetic waves are
decided by their wavelengths and not by the method of their excitation.
The above table shows the various parts of the electromagnetic spectrum with wavelength
range, frequency range and the names of the sources of the various electromagnetic
radiations.
Uses of Electromagnetic Spectrum

The following are some of the uses of electromagnetic spectrum:
1. Radio and microwave radiations are used in radio and TV communication system.
2. Infra-red radiations are used:
a. In revealing the secret writings on the ancient walls.
b. In green houses to keep the plants warm.
c. In war fare, for looking through haze, fog or mist as these radiations can pass
through them.
d. In electrotherapy for the heating of soft tissues.
3. Ultra-violet radiations are used in the detection of invisible writing, forged documents,
finger prints in forensic laboratory and to preserve the food stuffs. Ultra-violet
radiations are used in electrotherapy for the treatment of various skin conditions.
4. X-rays can pass through soft tissues but not through bones. This property of X-rays is
used in medical diagnosis, after X-ray films are made.
5. Electromagnetic waves of suitable frequencies are used in medical science for the
treatment of various diseases.
6. Super high frequency electromagnetic waves are used in radar and satellite
communication.
Electric shock
Shock: Shock is stage of unconsciousness which could be due to so many causes. Examples
are: hypovolemic, neurogenic, psychogenic and electric shock etc.
Electric shock: Electric shock is a painful stimulation of sensory nerves caused by:
1. Sudden flow of current
2. Cessation or pause of flow of current
3. Variation of the current passing through the body
Causes of Electric Shock

1. Poorly designed electromedical apparatus
2. Improper insulation of equipment
3. Improper insulation of wires
4. Badly serviced medical equipment
5. Mishandling of apparatus
6. Improper guidance to the patient
7. Lack of proper safety measures
Severity of Electric Shock

1. In accordance with the Ohms Law, resistance is inversely proportional to current.
Hence, lower the resistance of the skin the greater the current which passes through
the body. Therefore, if exposed part of the circuit is touched with wet hands, the shock
is more likely to be severe than if the hands are dry.
2. The greater the current passing through the body the more severe is the shock.
3. The severity also depends upon the path taken by the current. A strong current through
the head, neck or heart proves to be more fatal.
4. The severity also depends upon the type of current which passes through the body.
Individuals can be electrocuted by using appliances of as little as 40 volts direct current
in industry.
Types of Electric Shock

According to the severity of the shock, it could be of following types:
1. Minor electric shock
2. Major or severe electric shock
Effects of Electric Shock

1. Minor electric shock: In minor electric shock the victim gets frightened and distressed.
In this type of shock, there is no loss of consciousness.
2. Major or severe electric shock: In major or severe electric shock there is a fall of blood
pressure and patient may become unconscious. There could be cessation of respiration,
followed by ventricular fibrillations and cardiac arrest. These could be diagnosed by
seeing absence of pulse in the carotid artery and with fully dilated pupils.
Treatment of Electric Shock

1. The current should be switched off immediately.
2. The victim to be disconnected from the source of supply.
3. If there is no switch in the circuit, the victim must be removed from contact with the
conductor, but rescuer must take care not to receive a shock himself from touching
the affected person, contact with whom should be made only through a thick layer of
insulating material.
4. Following a minor shock the patient is to be reassured that everything is alright and
allowed to rest.
5. Water may be given to drink, but hot drinks should be avoided as they may cause
vasodilatation.
6. Tight clothing should be loosened and plenty of air allowed.
7. If respiration has ceased, the airway must be cleared and artificial respiration is to be
commenced immediately by the mouth to mouth or mouth to nose method.
8. Cardiopulmonary resuscitation may also be given.
9. Oxygen therapy may also be administered if required.
10. Patient must be shifted to the hospital after the primary care.
Precautions to avoid electric shock

1. All apparatus should be tested before use.
2. Connections to be checked before application.
3. Controls should be checked to ensure that they are at zero before switching on.
4. Adequate warming up time should be allowed.
5. The current intensity should be increased with care.
6. Patients should never be allowed to touch electrical equipment.
7. All apparatus should be serviced regularly by a competent person.
8. Machine should be properly insulated.
9. Mishandling of apparatus by unqualified person should be avoided.
10. All safety measures should be taken before application to the patient.
Earth shock: When a shock is due to a connection between the live wire of the main and
the earth it is called an earth shock.
Earth circuit: Electric power is transmitted by one live cable and one neutral cable which
is connected to earth. The earth forms part of the conducting pathway and any connection
between the live wire of the main and earth completes a circuit through which current
passes. If some person forms part of this circuit he receives an earth shock. Thus an earth
shock is liable to occur if any person makes contact with the live wire of the main while
connected to earth.
Causes of Earth Shock

Earth shock may be caused by the following two reasons:
1. Connection to the live wire.
2. Connection to the earth.
Connection to the live wire

a. When wire is not properly insulated.
b. When, the switch is put in the neutral wire, the neutral wire is disconnected and live
wire is not disconnected.
c. Live wire is touched to metal casing.
d. Live wire is touched to any wet thing.
Connection to the earth

a. If the floor is made up of stone.
b. If the conductor is touching any wire which is connected to the earth, such as gas pipe
or water pipes.
c. If the conductor is touched to any radiated metal casing or metal wire.
Precautions
1. Proper arrangement of the physiotherapy department.
2. Proper flooring should be done with rexin.
3. Insulation should be proper.

4. While treatment patient should not touch any of the machine part.
5. The metal casing of all apparatus must be connected to the earth.
6. The floor should be kept dry.
7. While using water containers, containing water, should be kept on an insulating material,
e.g. a wooden table.
8. Leaky bathtub should not be used.
9. The bathtub should not have fixed taps or water pipes.
Examples
Simultaneous connection to the live wire and earth can occur in a variety of ways,
1. A patient who is receiving treatment with a current that is not earth-free may rest her
hand on a water pipe.
2. A physiotherapist holding an electrode that is connected to the live wire may touch the
earthed apparatus-casing.
3. If someone standing on a damp stone floor touches the casing of apparatus which is
not connected to earth and with which the live wire is in contact, he too will receive an
earth shock.
PHYSICAL PRINCIPLES OF LIGHT

Multicolored rainbows, blue skies, green forests, etc. can be enjoyed by those who have
eyes with which to see them. By studying the branch of physics called optics, which deals
with the behavior of light and other electromagnetic waves, we can reach deeper apprecia-
tion of the visible world. A knowledge of the properties of light allows us to understand
the colors of the rainbow and designs of the optical devices such as telescopes, micro-
scopes, cameras, eyeglasses and the human eyes. The same basic principles of light also lie
at the heart of the some modern equipments like laser, optical fibres, holograms, optical
computers and new techniques in medical imaging.
In this part of the chapter, we will study the laws of reflection and refraction and
concepts of dispersion, polarization and scattering of light. Also we will compare the
various possible description of light in terms of particles, rays or waves and how mirrors
and lenses work in cameras, telescopes or microscopes.
Until the time of Sir Issac Newton (16421727), most scientists thought that light
consisted of streams of particles (called corpuscles) emitted by light sources. Galileo and
others tried to measure speed of light. Around 1665, it was evident that light has wave
properties. In 1873, James Clark Maxwell predicted the existence of electromagnetic
waves and calculated its speed of propagation. This development along with the work
of Heinrich Hertz in 1887 showed conclusively that light is indeed an electromagnetic
wave.
The wave picture of light does not reveal the whole story. Several effects associated
with emission and absorption of light concludes a particle aspect, in that the energy
carried by light waves is packed in discrete bundles called photons or quanta. These
apparently contradictory wave and particle properties have been reconciled in 1930s
with development of quanta electrodynamics which is a comprehensive theory that
includes both wave and particle properties. The propagation of light is best described
by a wave model and the understanding of emission and absorption requires a particle
approach.
The fundamental sources of all electromagnetic radiation are electric charges in accel-
erated motion. All bodies emit electromagnetic radiation as a result of thermal motion of
their molecules. This radiation called thermal radiation is a mixture of different wave-
lengths. At sufficiently high temperatures, all matter emits enough visible light to become
luminous. Thus, hot matter in any form is a source of light. Familiar examples are: incan-
descent lamp, flame of a candle, coils in an electric heater, etc.
Light is also produced during electrical discharges through ionized gases. The bluish
light of mercury arc lamp, the orange-yellow light of sodium vapor lamp and various
colors of neon sign boards are common examples. A variation of the mercury arc lamp
is a fluorescent lamp. This light source uses a material called a phosphor to convert the
ultraviolet radiation from a mercury arc into a visible light. This conversion makes fluo-
rescent lamps more efficient than the incandescent lamps in converting electrical energy
into light.
A light source that has attained prominence in recent years is LASER. It is an acronym
of Light Amplification of Stimulated Emission of Radiation. In most light sources, light is
emitted independently by different atoms within the source. In a laser, by contrast, atoms
are induced to emit light in a cooperative, coherent fashion. The result is a very narrow
beam of radiation that can be enormously intense and that is monochromatic, i.e. having
single frequency than light from any other source. Laser now a days is used by physio-
therapists for treatment purposes.
Reflection and refraction

The ray model of light explains two of the most important aspects of light propagation:
Reflection and refraction. In a homogeneous medium, light travels along a straight path.
When a light wave strikes a smooth interface separating two transparent materials (such as
air and glass or water and glass), the wave is generally partly reflected and partly refracted
(transmitted) into the second material (Fig. 1.65). The phenomenon of change in path of
light as it goes from one medium to another is called refraction.
Fig. 1.64: The incident ray, reflected ray and the normal to
the reflecting surface lie in the same plane
Laws of reflection and refraction

1. The incident, reflected and refracted rays and the normal to the surface all lie in the
same plane (Fig. 1.64). The plane of the three rays is perpendicular to the plane of the
boundary surface between the two materials.
2. The angle of reflection is equal to the angle of incidence for all wavelengths and any
pair of materials. This relation, together with the observation that the incident and
reflected rays and the normal all lie in the same plane is called the law of reflection.
3. For monochromatic light and for a given pair of materials, a and b, on opposite sides of
the interface, the ratio of the sines of the angles where both angles are measured from
the normal to the surface, is equal to the inverse ratio of the two indexes of refraction:
Fig. 1.65: Refraction and reflection of light
This experimental result, together with the observation that the incident and refracted rays
and the normal all lie in the same plane, is called the law of refraction or Snells law, after
the Dutch Scientist Willebrord Snell.
Characteristic of the image formed by a plane mirror:
1. Image is as far as behind the mirror, as the object is in front of the mirror.
2. The size of the image is same as that of the object.
3. The image formed is virtual in nature.
4. The image formed is erect in nature.
5. The image formed is laterally inverted. The lateral inversion means that the right side
of the object appears as the left side of the image and vice versa.
The portion of a reflecting surface, which forms part of a sphere is called a spherical mirror.
The spherical mirrors are of two types:
Concave spherical mirror: A spherical mirror whose reflecting surface is toward the centre
of the sphere of which mirror forms a part is called concave spherical mirror.
Convex spherical mirror: A spherical mirror whose reflecting surface is away from the
centre of the sphere of which mirror forms a part is called convex spherical mirror.
Pole: The centre of spherical mirror is called its pole.
Principal axis: The line joining the pole and the centre of curvature of the mirror is called
the principal axis of the mirror.
Centre of curvature: The centre of sphere of which mirror forms a part is called the centre
of curvature of the mirror.
Radius of curvature: The radius of sphere of which mirror forms a part is called the radius
of curvature of the mirror.
Aperture: The diameter of the mirror is called aperture of the mirror.
Principal focus: The point at which a narrow beam of light incident on the mirror parallel
to its principal axis after reflection from the mirror meets or appears to come from is called
principal focus of the mirror.
Focal length: The distance between the pole and the principal focus of the mirror is called
the focal length of the mirror.
Applications of plane or curved mirrors:
1. Concave mirrors are used for dressing up or used as make up mirrors. It is because a
person keeps his body or face between pole and focus of the concave mirror, a highly
magnified image of his body or face is formed.
2. Concave mirrors are used by dental surgeons for examining dental cavities.
3. Concave mirrors are used by ophthalmologists for examining the eye.
4. Concave mirrors are used as reflectors in cinema projectors, magic lanterns, etc.
5. Concave mirrors are used to make reflecting type astronomical telescope of large aperture.
6. Concave parabolic mirrors are used in search lights.
7. Convex mirrors are used in vehicles as drivers mirror. The driver of the vehicle can get
a clear and much wider field of view of the objects behind him.
8. Convex mirrors are used as a safety feature at sharp turns or dangerous corners of the
road. These are also used to prevent shop lifting activities in the market.
Dispersion
Ordinary white light is a superposition of waves with wavelengths extending throughout
the visible spectrum. The speed of light in vacuum is the same for all wavelengths, but the
speed in a material substance is different for different wavelengths. Therefore, the index of
refraction of a material depends on wavelength. The dependence of wave speed and index
of refraction on wavelength is called dispersion. The phenomenon of splitting up of white
light into its constituent colors is called dispersion of light.
If a beam of white light is made to fall on one face of a prism, the light emerging from
the other face of the prism consists of seven colors namely violet, indigo, blue, green, yellow,
orange and red. The deviation suffered by the violet color is maximum, while that by the red
is minimum. The band of seven colors produced at the screen is called spectrum (Fig. 1.66).
Scattering of light
The sky is blue. Sunsets are red. Skylight is partially polarized; thats why the sky looks
darker from some angles than from others when it is viewed through polarized sunglasses.
It turns out that one phenomenon is responsible for all of these effects. When you look at
the daytime sky, the light you see is sunlight that has been absorbed and then reradiated
in a variety of directions. This process is called scattering. When light falls on particles of
Fig. 1.66: Dispersion of sunlight or white light on passing through a glass prism.
The relative devtation of different colors shown is highly exaggerated
large size such as dust and water droplets, it does not get scattered. However, when light
travels through the atmosphere, it gets scattered from the air molecules. The blue light
(light of smaller wavelength) is scattered more than red light (light of longer wavelength),
when the light travels through the atmosphere.
Sir CV Raman was awarded Nobel prize for his work on elastic scattering of light by
molecules. It is popularly known as Ramans effect.
Wavefront
According to wave theory of light, a source of light sends out disturbances in all directions.
In a homogenous medium, the disturbances reaches all those particles of the medium in
phase with each other and therefore at any instance, all such particles must be vibrating in
phase with each other. The locus of all the particles of the medium, which at any instant
are vibrating in the same phase is called the wavefront.
Depending upon the shape of the source of light, wavefront can be of following types:
Spherical wavefront: A spherical wavefront is produced by a point source of light
(Fig. 1.67A).
Cylindrical wavefront: When the source of light is linear in shape (such as a slit), a cylindrical
wavefront is produced.
Plane wavefront: A small part of a spherical or a cylindrical wavefront originating from a
distant source will appear plane and hence called a plane wavefront (Fig. 1.67B).
Huygens principle
Huygens principle is a geometrical construction which is used to determine the new posi-
tion of a wavefront at a later time from its given position at any instant. In other words,
Huygens principle gives a method to know as to how light spreads out in the medium.
Huygens principle is based upon the following assumptions:
a. Each point on the given or primary wavefront acts as a source of secondary wavelets,
sending out disturbances in all directions in a similar manner as the original source of
light does.
A B
Figs 1.67A and B: Wavefront. (A) When the wavefront are spherical, the rays rodiate out from
the centre of the sphere; (B) When the wavefront are planes, the rays are parallel
b. The new position of the wavefront at any instant (called secondary wavefront) is the
envelope of the secondary wavelets at that instant.
Interference of light
When a source of light emits energy, the distribution of energy is uniform in the medium,
but when two sources of light lie close to each other and emit light of same wavelength
and preferably of same amplitude, then due to superposition of waves from the two
sources, the distribution of light energy no longer remains uniform. The phenomenon of
non uniform distribution of energy in the medium due to superposition of two light waves is called
interference of light.
At some points in the medium, the intensity of light is maximum (constructive
interference), while at some other points, the intensity is minimum (destructive
interference).
Thomas Young (1801) demonstrated the interference of light experimentally. His
experiment led to the conclusion that light has a wave nature.
Diffraction
The phenomenon of bending of light round the sharp corners and spreading into the regions of
the geometrical shadow is called diffraction. The light waves are diffracted only when the size
of the obstacle is comparable to the wavelength of the light. All types of wave motion exhibit
diffraction effect. Sound waves or radiowaves shows diffraction effect in day-to-day life.
Polarization
In general, waves are of two types:
1. Longitudinal waves: The waves in which particles oscillate along the direction of
propagation of the waves are called longitudinal waves.
2. Transverse waves: The waves in which direction of oscillation of particles is perpendicular
to the direction of propagation of the waves are called transverse waves.
Both types of waves exhibit the phenomenon of reflection, refraction, diffraction and
interference but polarization of the waves is only exhibited by the transverse waves. Polar-
ization is characteristic of all transverse waves. This is the only phenomenon where two
types of waves essentially differ from one another.
When a wave has only y-displacements, we say that it is linearly polarized in y-direction;
a wave in z-displacements is linearly polarized in the z-direction. The phenomenon due to
which the vibrations of light are restricted in a particular plane is called the polarization of light. For
mechanical waves we can build a polarizing filter, or a polarizer that permits only waves
with a certain polarization direction to pass. Commonly used polarisers are tourmaline
crystal or nicol prism.
PHYSICAL PRINCIPLES OF SOUND

Ripples in a pond, musical sounds or seismic tremors triggered by an earthquakeall
these exhibit a wave phenomenon. Waves can occur whenever a system is disturbed from
equilibrium and when the disturbance can travel or propagate from one region to other.
As a wave propagates, it carries energy. The energy of seismic waves can be so high that it
can break the earths crust.
Waves in a string play an important role in music. When a musician strums a wave or
bows a violin, he makes waves that travel in opposite directions along the instruments
strings. What happens when those oppositely directed waves overlap is called interference.
Not all waves are mechanical in nature. Electromagnetic waves like light, radiowaves,
infrared and ultraviolet radiations, etc. can propagate in vacuum or empty spaces, where
there is no medium.
Mechanical Waves
A mechanical wave is a disturbance that travels through some material or substance called
the medium for the wave. As the wave travels through the medium, the particles that make
up the medium undergo displacements of various kinds, depending on the nature of the
wave. If the displacements of the medium are perpendicular or transverse to the direction
of travel of the wave along the medium, it is called a transverse wave. Examples can be seen
in a string or rope.
If the displacements of the medium are parallel or longitudinal to the direction of travel
of the wave along the medium, it is called a longitudinal wave. Examples can be seen in a
fluids (liquid) or gases.
If the displacements of the medium are both parallel and perpendicular to the direction
of travel of the wave along the medium, it is called a mixed wave. Examples can be seen
in a water canal.
These examples have three on common. First in each case the disturbance travels or
propagates with a definite speed through the medium. This speed is called the speed of
propagation, or simply the wave speed. It is determined in each case by the mechanical
properties of the medium. Second, the medium itself does not travel through space; its
individual particles undergo back-and-forth or up-and-down motions around their equi-
librium positions. The overall pattern of the wave disturbance is what travels. Third, to
set any of these systems into motion, we have to put in energy by doing mechanical work
on the system. The wave motion transports this energy from one region of the medium to
another. Waves transport energy, but not matter, form one region to another.
Periodic Waves
The transverse wave on a stretched string is an example of a wave pulse. The hand shakes
the string up and down just once, exerting a transverse force on it. The result is a single
wiggle or pulse that travels along the length of the string. The tension in the string
restores its straight line shape once the pulse has passed. When we give the free end of
the string a repetitive or periodic motion, then each particle in the string also undergoes
periodic motion as the wave propagates and we have a periodic wave.
As the wave moves, any point on the string oscillates up-and-down about its equi-
librium position with simple harmonic motion. When a sinusoidal wave passes through
a medium, every particle in the medium undergoes a smiple harmonic motion with the
same frequency.
For a periodic wave, the shape of the string at any instant is a repeating pattern. The
length of one complete wave pattern is the distance from one crest to the next or from one
trough to the next or from any point to the corresponding point on the next repetition
of the wave shape. This is called wavelength of the wave which is denoted by (Greek
letter lambda). The wave pattern travels with a constant speed and advances a distance
of one wavelength in a time interval of one period T. So, the wave speed is given by
= /T
or because f = 1/T
=f
The speed of propagation equals the product of wavelength and frequency. The frequency
is a property of the entire periodic wave because all points on the string oscillate with the
same frequency f.
Sound Waves
Sound is a mechanical wave that is an oscillation of pressure transmitted through a solid,
liquid, or gas, composed of frequencies within the range of hearing and of a level sufficiently
strong to be heard, or the sensation stimulated in organs of hearing by such vibrations.
Propagation of sound
Sound is a sequence of waves of pressure that propagates through compressible media
such as air or water. During propagation, waves can be reflected, refracted, or attenuated
by the medium.
The behavior of sound propagation is generally affected by three things:
A relationship between density and pressure. This relationship, affected by tempera-
ture, determines the speed of sound within the medium.
The propagation is also affected by the motion of the medium itself. For example, sound
moving through wind. Independent of the motion of sound through the medium, if the
medium is moving the sound is further transported.
The viscosity of the medium also affects the motion of sound waves. It determines the
rate at which sound is attenuated. For many media, such as air or water, attenuation
due to viscosity is negligible.
When sound is moving through a medium that does not have constant physical properties,
it may be refracted (either dispersed or focused).
Perception of sound
The perception of sound in any organism is limited to a certain range of frequencies.
For humans, hearing is normally limited to frequencies between about 20 Hz and
20,000 Hz (20 kHz), although these limits are not definite. The upper limit generally
decreases with age. Other species have a different range of hearing. For example, dogs
can perceive vibrations higher that 20k Hz, but are deaf to anything below 40 Hz. As a
signal perceived by one of the major senses, sound is used by many species for detecting
danger, navigation, predation, and communication. Earths atmosphere, water and
virtually any physical phenomenon, such as fire, rain wind or earthquake, produces
(and is characterized by) its unique sounds. Many species, such as frogs, birds, marine
and terrestrial mammals, have also developed special organs to produce sound. In some
species, these produce song and speech. Furthermore, humans have developed culture
and technology (such as music, telephone and radio) that allows them to generate,
record, transmit and broadcast sound. The scientific study of human sound perception
is known as psychoacoustics.
Physics of Sound
The mechanical vibrations that can be interpreted as sound are able to travel through all
forms of matter: solid, liquid or gases. The matter that supports the sound is called the
medium. Sound cannot travel through a vacuum.
Longitudinal and transverse waves
Sinusoidal waves of various frequencies; the bottom waves have higher frequencies than
those above. The horizontal axis represents time.
Sound is transmitted through gases, plasma, and liquids as longitudinal waves, also
called compression waves. Through solids, however, it can be transmitted as both longi-
tudinal waves and transverse waves. Longitudinal sound waves are waves of alternating
pressure deviations from the equilibrium pressure, causing local regions of compression
and rarefction, while transverse waves (in solids) are waves of alternating shear stress at
right angle to the direction of propagation.
Matter in the medium is periodically displaced by a sound wave, and thus oscillates. The
energy carried by the sound wave converts back-and-forth between the potential enery of
the extra compression (in case of longitudinal waves) or lateral displacement strain (in case
of transverse waves) of the matter and the kinetic energy of the oscillations of the medium.
Sound Wave Properties and Characteristics

Sound waves are often simplified to a description in terms of sinusoidal plane waves,
which are characterized by these generic properties:
Frequency, or its inverse, the period
Wavelength
Wave number
Amplitude
Sound pressure
Sound intensity
Speed of sound
Direction.
Sometimes speed and direction are combined as a velocity vector; wave number and direc-
tion are combined as a wave vector.
Transverse waves, also known as shear waves, have the additional property, polariza-
tion, and are not a characteristic of sound waves.
Speed of Sound
The speed of sound depends on the medium the waves pass through, and is a fundamental
property of the material. The physical properties and the speed of sound change with ambient
conditions. For example, the speed of sound in gases depends on temperature. In 20C
(68F) air at the sea level, the speed of sound is approximately 343 m/s (1,230 km/h; 767 mph).
In fresh water, also at 20C, the speed of sound is approximately 1,482 m/s (5, 335 km/h; 3,315
mph). In steel, the speed of sound is about 5,960 m/s (21,460 km/h; 13,330 mph).
Low Frequency
2 Currents
Faradic Type Current

Faradic type current is short duration interrupted
direct current with pulse duration of 0.11 ms
and frequencies between 50100 Hz, used for
the stimulation of innervated muscles. The term
faradism was previously used to signify the type
of current produced by the first faradic coil and
was unevenly alternating current with each cycle
consisting of two unequal phases (Fig. 2.1):
1. Low intensity long duration current
2. High intensity short duration current.
Faradic coils have now been replaced by electronic Fig. 2.1: Pure faradic current
stimulators (Figs 2.2A and B) which almost have
Fig. 2.2A: Low frequency current apparatus Fig. 2.2B: Treatment accessories
the same physiological effect but differs in

the waveform (Fig. 2.3). The features essential
for the production of these physiological effects
are the impulses with duration of 0.11 ms with a
frequency of 50100 Hz.
Modified Faradic Current

For better results in the treatment, faradic current
is always surged to produce a near-normal
tetanic-like contraction and relaxation of the
Fig. 2.3: Faradic current from electronic
muscle. The apparatus should have sufficient
stimulator
control to surge the current so that the intensity
of successive impulses increases gradually with
surges varying in waveform to provide satisfactory muscle contraction and relaxation. In
the original faradic coils, the current was surged by hand but in modern stimulators an
electronic device is used. The circuit can be modified to give surges of various durations,
frequencies and waveforms. Various forms of surge are available, such as trapezoidal,
triangular and saw-tooth impulses, and that most suitable for each patient must be selected
(Fig. 2.4).
Electrotherapeutic Currents
Alternating, Direct and Pulsed Currents
Electrotherapeutic currents are basically of three types. These are alternating (AC), direct
(DC), or pulsed. Specific therapeutic effects are produced by these electrotherapeutic
currents, which are capable of producing specific physiologic changes when introduced
into the biological tissues.
Direct current also referred as galvanic current or constant galvanism which has a
unidirectional flow of electrons toward the positive pole (Fig. 2.5A). In modern devices, the
polarity and thus the direction of the flow of current, can also be reversed. The therapeutic
use of this unidirectional flow of current is to introduce medication into the body tissues is
called as Iontophoresis (LeDuc, 1903). Some apparatus have the capability of automatically
reversing polarity, in which case the physiologic effects will be similar to AC current.
Interrupted direct current: If the continuous unidirectional current is interrupted, it
gives rise to series of pulses or phases of unidirectional current. A current, which varies
sufficiently in magnitude, can stimulate a motor nerve and so produces contraction of
the muscles to which it supplies. Suitable current can also stimulate denervated muscle.
Intermittent direct currents are used in these cases, which ranges from 0.01 to 3 ms. The
equipment commonly provides duration of 0.01, 0.03, 0.1, 0.3, 1, 3, 10, 30, 100 and 300 ms.
In an alternating current, the flow of electrons constantly changes direction, or stated
differently, reverses its polarity. Electrons flowing in an alternating current always
move from the negative to positive pole, reversing direction, when polarity, if reversed
(Figs 2.5B and C).
Low Frequency Currents 77
Fig. 2.4: Unmodified and modified (surged) form of faradic current

Figs 2.5A to C: (A) Direct monophasic current, (B) Alternating biphasic current and
(C) Pulsed polyphasic current
Evenly Alternating Currents

1. Sinusoidal currents: Sinusoidal currents
are evenly alternating sine wave currents
of 50 Hz. This gives 100 pulses or phases
in each second of 10 ms each, 50 in one
direction and 50 in another (Fig. 2.6).
It is produced from the mains by reducing
the voltage to 6080 V with a step-down
transformer. It is usually surged to
cause rhythmical muscle contractions. It Fig. 2.6: Sinusoidal current
relieves pain and reduces edema.
Because of marked sensory stimulation
this current is often applied to large areas and rarely used for local muscle stimulation.
2. Diadynamic currents: Introduced by Pierre Bernard nearly 70 years ago, they are
sinusoidal, direct currents being rectified mains type currents with frequency of
50-100 Hz. There are six different types of currents, which are each used for different
purposes.
The MF (monophase) is a half-sinusoidal alternating current, which is created by a
one-way DC converter of 50 Hz, with an impulse length and interruption of 10 ms
each. The primary effect of this type of current is muscle stimulation (Fig. 2.7A).
The DF (diphase) type of current is created by an alternating current of
50 Hz by means of a two-way DC converter, so that a current of 100 Hz is achieved.
The patient feels a stabbing sensation in the treated area. The stimulus is less than
that of the MF and primarily affects the autonomic nervous system in the sense of
lowering the increased sympathetic tone (Fig. 2.7B).
The short-period current (SP) involves a sudden alternation of MF and DF currents.
The patient senses the abrupt change between the tensing MF current and relaxing
DF current (Fig. 2.7C).
In the long-period (LP) current, the MF current is mixed with a second modulated

MF. The gradual raising and lowering of the amplitude is experienced by the
patient as a more pleasant sensation than that produced by SP (Fig. 2.7D).
In the syncopated rhythm (RS) the current is interrupted by a pause of 0.9 second

after a current flow of 1.1 second. This type of current is used for the electrical
stimulus of the muscles (Fig. 2.7E).
The modulated monophase (MM) current not listed by Bernard is a logical extension

of his currents. In the MM the RS is gradually reduced in stepwise fashion. Like
the RS, the MM is suited for the treatment of muscular atrophies, but the faradic
excitability of the particular muscles must be maintained (Fig. 2.7F).
The therapeutic effects of the diadynamic currents have been researched and estab-
lished in numerous studies (Bernard).
Therapeutic Effects (Rennie, 1988)

Pain relief

Decrease inflammation and swelling

Muscle reeducation

Increase local circulation

Facilitation of tissue healing.

Interrupted Galvanic Current: It is called as long duration current having duration of more
than 1 ms upto 300 or 600 ms. Interruption is the most usual modification of direct current, the
flow of current commencing and ceasing at regular intervals. The rise and fall of intensity may
be sudden and may be of rectangular, saw-tooth, triangular and trapezoidal type (Fig. 2.8).
The impulse in which the current rises gradually are often termed selective because
a contraction of denervated muscle can often be produced with an intensity of current
that is insufficient to stimulate the motor nerve. This occurs due to accommodation. It is
often found that the more long-standing the denervation, the slower the rise in intensity of
current that is required.
An impulse of 100 ms duration is often used which requires frequency of 30 Hz. But as
you increase the duration, frequency must be reduced.
To eliminate the danger of chemical burn reverse wave of current, i.e. depolarized
impulses should be used, which also reduces the skin irritation.
Production of interrupted DC is usually accomplished in modern apparatus by circuits,
which employ transistors and timing devices. Current is always applied to the patient via
potentiometer as this allows the intensity of current to be turned up from zero.
erve ransmission
N
t
In normal nerve, there is difference of concentration of ions inside and outside the nerve.
Due to this there is difference of potential called as potential difference between inside and
outside of the nerve.
Nerve remains in two states:
1. Resting state

2. Stimulated state.

Figs 2.7A to F: Modulations of various phases of diadynamic currents

Fig. 2.8: Modified DC impulses
In resting nerve, the nerve is positive outside and negative inside (Fig. 2.9). At this
time, the nerve is not permeable to Na+ ions, so it is called as polarized state of nerve.
When a nerve is stimulated, it causes fall in potential difference (PD). When the fall
reaches to a certain level, it provides the permeability of sodium ions. This permeability
Fig. 2.9: Nerve transmissionresting state
Fig. 2.10: Nerve transmissionstimulated state
causes the difference in concentration of ions inside and outside the nerve and thus further
fall of PD until reversal of polarity occurs. Now the membrane is positive inside and
negative outside (Fig. 2.10).
Immediately after this activity the Na+ ions are pumped again and the stimulated part
again comes to resting state.
Now the difference between the active and resting part of the nerve causes the local
electron flow between the active and resting part of the nerve. The direction of electron
flow through the membrane is opposite to the PD across the fiber.
The fiber acts as a resistance to current so that current flow lowers the PD, this again
make the membrane permeable to Na+ ions and cause the reversal of PD as before. These
changes of PD are then propagated along the length of nerve fiber. This change of polarized
stage causes the travel of impulse.
Electrical Stimulation of Nerves

To initiate the nerve impulse, varying current of
adequate intensity must be applied. Potential
difference (PD) is being formed when current
flows in plasma membrane of nerve fibers and
resistance lies in series with other tissues. The
membrane nearer to cathode will be negative and
is denoted by n, whereas, surface nearer to anode
will be positive and is denoted as p (Fig. 2.11).
Increase in PD occurs on the nerves nearer to Fig. 2.11: Potential difference across
anode, whereas the PD decreases in the membrane a nerve fiber
nearer to the cathode because of opposite polarity.
When the membrane becomes permeable to
Na+ ions by fall in PD to a certain level, then the ions enter the axon and initiate the nerve
impulse.
When cathode is applied to superficial nerve then nearest side will get activated but the
anode can only initiate the nerve impulse. Therefore, further aspect of anode is activated.
Due to this, the density of current is less in further aspect of nerve fiber than near one.
So for initiating impulse cathode is more effective than anode. In some apparatus, polarity
of terminals is marked which is beneficial for high peak of current for effective stimulus.
To get contraction of innervated muscle in less current, cathode should be connected to
active electrode.
Accommodation
When a constant current flows, the nerve adapts itself. This phenomenon is known as
accommodation.
Effect of Frequency of Stimulation

The muscle responds with a large contraction and then rotates to its resting state. It is called
twitch contraction. When single stimulus is applied per second then there is contraction
followed by immediate relaxation. Increase in the frequency of stimuli up to 20 Hz shortens
the period of relaxation.
If stimuli are given more than 20 Hz then there is no time for complete relaxation
between the contraction and another impulse. At more than 60 Hz, there is no relaxation at
all and current flows smoothly leading to tetanic contraction.
Strength of Contraction
It depends on:
1. Quantity of motor nerve activated

2. Rate of change of current.

If intensity of current rises suddenly, less intensity is required for muscle contraction as
there is no time for accommodation but if current rises slowly greater intensity is required
as in trapezoidal, triangular current, etc.
Pathological Changes in Peripheral Nerve

Peripheral nerves may be damaged by injury or disease in many different ways and the
nerve fiber is affected in following ways:
1. It can be stopped over a small section of the nerve fiber a local block, so that conduction

above and below is normal (in neuropraxia).
2. It can be slowed which is usually due to the myelin sheath being affected.

3. It can be stopped over a small section of the nerve fiber, a local block. It can be stopped

over the whole distal length of nerve from site of injury to the skin and muscle, as in
neurotmesis and axonotmesis or damage to nerve cell.
eddons lassification
S
C
Neuropraxia
Temporary mild compression of the nerve will lead to a conduction block called as
neuropraxia. It causes displacement of the myelin sheath and local edema of the nerve
fiber. The damage is not so severe to cause degeneration of the fiber. As there is no
permanent damage so recovery occurs rapidly in a few days or weeks. Since only a
section of a nerve fiber is affected, conduction beyond the blockage is normal, thus
electrical stimulation of motor nerve fiber beyond the block will cause muscle contraction.
Electrical stimulation applied proximal to the block does not result in muscle contraction.
Axonotmesis
More severe compression injury may cause sufficient damage to the nerve axon. Degen-
eration of the axon takes place including the myelin sheath. Example of this type of lesion
isradial nerve palsy in fractured shaft of humerus. Once the nerve fiber has degenerated,
alteration in electrical reaction occurs.
Neurotmesis
Instead of compression if the injury is such as to disrupt all tissues of the nerve fiber such
as a cut through the nerve, then the distal segment will degenerate completely. Since the
tissue is totally disrupted the axon filament will not readily find correct channels down
to regrow, so that recovery is at best imperfect. This is called as neurotmesis. Such lesion
often requires surgery to ensure that the two cut ends are sufficiently approximated to
allow successful growth.
rocess of enervation
P
D
Severe injury to the nerve causes damage to the nerve axon so that it is unable to support
the metabolic process of its distal part resulting in degeneration of the whole length of the
new fiber including the myelin sheath distal to the lesion. This process is called Wallerian
degeneration. It takes as long as 14 days to degenerate. The distal section of nerve remains
excitable and can conduct impulse before degeneration has taken place.
Because of this it may not be possible to make full assessment of the lesion till three
weeks, after suspected nerve injury.
egeneration of erve
R
N
In axonotmesis, the fibrous framework of the bundle of nerve fibers remain intact and
fills a chain of Schwann cells so that ultimately nerve fibrils sprouting from the intact
proximal part of the nerves are guided in their proper channels to reform the complete
nerve process.
The duration needed for full recovery will depend on the site of the lesion and the
length of nerve that has to regrow. The rate of regrowth is somewhat variable, being more
rapid at first, up to 5 mm per day, but is usually considered to be an average 12 mm per
day.
When there is degeneration of the nerve fiber the normal response is reduced or lost
and the changes become evident 3 or 4 days after injury. Changes in the reaction obtained
on stimulation over the muscle, may be observed before the end of first week.
W V F M
A
E
OR
S
The term waveform means the graphical representation of the direction, shape, amplitude,
duration and pulse frequency of the electrical current produced by the electrotherapeutic
device. The instrument which is used to display the electric current is called an oscilloscope.
ulses, hases and irection of urrent Flow

P
P
D
C
The individual waveform as shown by an oscilloscope is referred to as a pulse. A pulse may
contain either one or two phases (Fig. 2.12). It rises above or goes below the baseline for
some specific period of time. Direct current, also referred to as monophasic current, produces
waveforms that have only a single phase in each pulse. Current flow is unidirectional,
always flowing in the same direction toward either the positive or negative pole. Conversely,
alternating current, also referred to as biphasic current, produces waveforms that have
two separate phases during each individual pulse. Current flow is bidirectional, reversing
direction or polarity once during each pulse. Biphasic waveforms may be symmetrical or
asymmetrical. If both phases of the waveform may be symmetrical, the shape and size of each
phase is identical (Fig. 2.13). ulsed current waveforms are called polyphasic currents and
p
are representative of electrical current that is conducted as a series of pulses of short duration
followed by a short period of time, when current is not flowing called the interpulse interval.
Single current may flow in one direction as in direct current or may reverse direction of flow
as in alternating current. With pulsed currents, there is always some interruption of current
flow.
Fig. 2.12: WaveformBiphasic pulse

Fig. 2.13: Waveformmonophasic pulse
Waveform Shape
Waveform shape could be of any type like sine, rectangular, or triangular waveform
depending on the capabilities of the generator producing the current. Alternating, direct
and pulsed currents may be of the following waveform shapes as shown in the Figure 2.14.
Pulse Amplitude
The maximum amplitude of a pulse can be shown by the tip of highest point of each phase.
The amplitude of each pulse reflects the intensity of the current. The term amplitude is
synonymous with the terms voltage and current intensity. The higher the amplitude, the
greater is the voltage or intensity.
The total current cannot be confused with the tip of highest point of a phase. The total
current delivered to the tissues can only be calculated by averaging the current flowing per
unit time including the interpulse intervals. The electrical generators that produce short
duration pulses, the total current produces (coulomb/sec) is low compared to peak current
amplitudes due to long interpulse intervals. Thus, the average current or the amount of
current flowing per unit of time is relatively low. Average current can be increased by either
increasing pulse duration, increasing pulse frequency, or by some combination of the two.
Pulse Charge
The term pulse charge indicates the total amount of electricity that is delivered to the
patient during each pulse. In monophasic currents, the phase charge and the pulse charge
are the same and are greater than zero. With biphasic currents the pulse charge is equal to
Fig. 2.14: Waveform shapes
the algebric sum of the phase charges. If the pulse is symmetrical the net pulse charge is zero.
In asymmetrical pulses, the net pulse charge cannot be zero.
Rise and Decay Time

The rate of rise in amplitude or the rise time indicates the time taken by a pulse to reach
its maximum amplitude in each phase. Conversely, decay time refers to the time taken
by a pulse to return to neutral. The rate of rise is important therapeutically so as to
avoid accommodation of the nerves to the constant amplitude current, which results in
constant level of depolarization and nerves become unexcitable at that same intensity or
amplitude. Rate of rise and decay times are generally short, ranging from nanosecond
to millisecond.
By observing the three different waveforms, it is apparent that the sine wave has a
gradual increase and decrease in amplitude for both alternating and direct currents. The
rectangular wave has an almost instantaneous increase in amplitude, which plateaus for
a period of time and then abruptly falls off. The shape of these waveforms as they reach
their maximum amplitude or intensity is directly related to the excitability of the nervous
tissue. The more rapid the increase in amplitude or the rate of rise, the greater the currents
ability is to excite nervous tissue.
Most modern DC generators make use of a twin-peak triangular pulse of very short
duration and peak amplitudes as high as 500 V. Combining high-peak intensity with a
short-phase duration produces a very comfortable type of current as well as an effective
means of stimulating sensory, motor and pain fibers.
Asymmetric Waveforms
The use of asymmetrical waveforms for therapeutic purposes is now of the past. The true
faradic waveform is also no longer being used. The so-called true faradic current is like a
biphasic pulsed current with asymmetric waveform. The original faradic current is like an
alternating current because there was always a reversal of direction of current flow. The
amplitude of the portion of the wave in the negative direction was not great enough to
produce any physiologic response.
In the monophasic sawtooth or exponential waveform the amplitude rises very
gradually and then falls abruptly. Current that uses this waveform stimulates denervated
muscle without affecting normally innervated muscle, since the gradual rise in amplitude
allows for accommodation of the normal muscle.
Exponential Current: The basic phenomenon is to rise the current impulses gradually.
When represented graphically, these impulses display a similarity to a triangle, which
is why this form of current is called triangular current. As the current does not increase
in a straight line, but rather in accordance with a mathematical exponential equation, the
current is also called exponential current.
Pulse Duration: The length of time that current is flowing in one cycle indicates duration of

each pulse. With monophasic current the phase duration is the same as the pulse duration.
It is the time from initiation of the phase to its end. With biphasic current the pulse duration
is determined by the combined phase durations. In some devices, it is prefixed and in some
the uses can alter it. The phase duration as well as pulse duration may be as short as few
microseconds or may be a long-duration direct current that flows for several minutes.
In pulsed currents and also in some cases with alternating and direct currents, the
current flow can be off for some period of time. The combined time of the pulse duration
and the rest duration or interpulse interval is known to as the pulse period.
Pulse Frequency: Pulse frequency is the number of pulses per second. Each individual pulse
either rises or falls from its base value. As the frequency of any waveform is increased,
the amplitude tends to increase and decrease more rapidly. The muscular and nervous
system responses depend on the length of time between pulses and on how the pulses
or waveforms are modulated. Muscle will respond with individual twitch contraction to
pulse rates of less than 50 pulses per second. At 50 pulses per second or greater, a tetany
will result, regardless of whether the current is biphasic, monophasic, or polyphasic.
urren Modula ion

C
t
t
The current modulation is an important phenomenon because the physiologic response
to the various waveforms depends largely on current modulation. Modulation refers to any
alteration in the magnitude or any variation in duration of these pulses. Modulation may
be continuous, interrupted, burst, or ramped. According to various treatment goals the
parameters of current modulation must be established.
ontinuous Modulation
C
Continuous modulation means that the
amplitude of current flow remains the same
for several seconds or minutes. Continuous
modulation is usually associated with long-pulse
duration direct current (Fig. 2.15A). With direct
current, flow is always in a uniform direction.
The positive and negative accumulation of
Fig. 2.15A: Continuous modulation
charged ions over a period of time creates either
an acidic or alkaline environment that may be of
therapeutic value. This therapeutic technique has been referred to as medical galvanism.
The technique of iontophoresis also uses continuous direct current to drive ions into the
tissues. If the amplitude is great enough to produce a muscle contraction, the contraction will
occur only when the current flow is turned on or off. Thus with direct current continuous
modulation, there will be a muscle contraction both when the current is turned on and when
it is turned off. Continuous modulation is also used with alternating current primarily to
elicit muscle contractions.
nterrupted Modulation
I
In interrupted modulation, current flows for
some period of time called the on-time, and is
then periodically turned off during the off-time.
On-time and off-time can be prefixed in some
devices or can be altered by the operator.
Interrupted modulation is used with monophasic
as well as for biphasic currents. Currents with sine,
rectangular, or triangular-shaped waveforms Fig. 2.15B: Interrupted modulation
may be interrupted. Interrupted modulation
is used clinically for muscle reeducation and
strengthening and for improving range of motion
(Fig. 2.15B).
Burst Modulation
Burst modulation occurs when pulsed current
flows for a short duration and then is turned
off for a short duration and in a repetitive
cycle. With polyphasic current, sets of pulses
are combined. These combined pulses are
most commonly referred to as bursts. These
are also called pulse packets, envelopes, pulse
Fig. 2.15C: Burst modulation
trains, or beats (Fig. 2.15C). The interruptions
between individual bursts are called interburst
intervals. The interburst interval may be too
short to have any effect on a muscle contraction. Thus, the physiologic effects of a burst of
pulses will be the same as with a single pulse. Bursts may be used with monophasic and
biphasic currents as well.
Ramping Modulation
In ramping modulation which is also called sometimes as surging modulation, current
amplitude increases gradually or decreases gradually in its intensity. It is also called
ramping-up or ramping-down of current modulation (Fig. 2.15D). Ramp-up time is usually
preset at about one-third of the on-time. The ramp-down option is not available on all
machines. This type of modulation gives the patient a very comfortable feeling because of
the very gradual rise of intensity of the current. Ramping modulation is used clinically to
elicit muscle contraction and is generally considered to be a very comfortable type of current.
Fig. 2.15D: Ramping modulation
Indications for the Use of Low Frequency Currents

1. Facilitation or initiation of the muscle action: When the patient is unable to produce
muscle contraction or finds it difficult to do so, electrical stimulation may be required
in assisting to produce voluntary contraction. In cases of pain, electrical stimulation of
motor neurons reduces the inhibition, which acts on larger anterior horn cells, so as to
facilitate the transmission of voluntary impulses to the muscles and helps in inducing
relaxation to its antagonists.
Initially treatment should be given in pain-free range so that no movement causing
pain is produced. Patient is advised to produce voluntary contraction along with the
electrical stimulation. The amount of voluntary contraction is increased gradually and

electrical stimulation is reduced until the muscles produce full voluntary contraction.
2. Reeducation or relearning of muscle action: According to Beavors theory, the brain
appreciates movements and not individual muscle action. In some situations where
muscle is not under voluntary control reeducation or relearning of muscle action is
required. These situations could be:
i. Prolonged disuse ii. Incorrect use.
In these circumstances faradic stimulation may be used to produce contraction and
thus help to restore the sense of movement.
Due to prolonged disuse person is not able to contract muscle voluntarily as in cases
of long-standing flat foot, reeducation of intrinsic muscles of foot is done by faradic
stimulation.
In cases where person is using incorrect pattern of movement, correct pattern is taught
by faradic stimulation, e.g. stimulation of abductor hallucis muscle in hallux valgus.
Active contractions should be attempted at the same time along with the electrical
stimulation.
3. Training/Teaching of a new muscle action: For training or teaching a new muscle action
faradic current is used. The cases where teaching a new muscle action is required, could
be:
i. Tendon transplantation surgery ii. Reconstructive operations.
In tendon transplantation and reconstructive operations a muscle is required to
perform a different or new action from which it was previously doing. For this,
faradic type current is required and muscle is stimulated in a new pattern. During this
treatment the patient must concentrate on a new movement and try to assist it along
with voluntary contractions.
4. Loosening and prevention of adhesion: Effusions in the tissues when stays there
form adhesion. Adhesions are formed where there is no proper muscle contraction.
If adequate active exercise is not possible, electrical stimulation in the form of faradic
current may be used to prevent adhesions. Muscle contraction loosens and stretches
the adhesions, which have already formed.
5. Improvement in venous and lymphatic drainage: Alternative contraction and relaxation
of muscles produces pumping action, which leads to venous and lymphatic drainage.
Effect of faradic current for improving venous and lymphatic drainage is described as
faradism under pressure, this is a very effective treatment of edema and gravitational ulcer.
6. Maintaining or increasing in range of movement: The movement may be limited
by shortening of different tissues and from different causes. Faradic stimulation of
muscle to stretch the shortened tissue is used in:
i. Contracture of fibrous tissue and scaring: Limitation of joint movement due to
shortening of soft tissue on one side of the joint has been treated by electrical
stimulation of the muscle that stretches the contracture.
ii. Deformities like scoliosis: In scoliosis lateral trunk muscles on the convexity of
the curve are stimulated electrically. Electrodes are placed at the patients back
and muscle contraction is obtained by stimulating the muscles in order to reduce

convexity.
7. Neuropraxia of a motor nerve: In neuropraxia, the impulses from brain are not
able to reach up to the muscles supplied by affected nerve through site of lesion. In
neuropraxia, there is no degeneration of nerve so if we stimulate the nerve below
site of lesion, the impulses will easily pass to the muscle and cause the contraction.
Electrical stimulation is not usually necessary in neuropraxia because recovery takes
place with any marked changes in the muscle tissue.
8. Severed motor nerve: When any nerve is damaged severely there occurs degeneration
of axons. Degeneration takes several days to complete, and for a few days after
the injury a muscle contraction may be obtained by faradic type current. But after
degeneration, muscles can be stimulated by interrupted direct current or modified
direct current.
9. For replacing orthosis: Low frequency stimulation may be used to enhance the
function of a paralyzed or weak muscles thus eliminating the need for a splint or brace
or orthosis.
10. Stimulation of denervated muscle: For stimulation of denervated muscle, interrupted
direct current or galvanic current is used which directly stimulate the muscle fiber. In
denervated muscle there occurs wasting and then fibrosis. Muscle looses its property
of contractility, excitability, elasticity and irritability. By electrical stimulation the
process of muscle wasting slows down, but it needs strong electrical impulses for this
purpose. Approximately 300 contractions per session are required, but this also is not
always practically possible due to muscle fatigue. So for treatment to be effective at
least 90 contractions need to be performed in a session. If fatigue occurs soon, number
of contractions may be reduced and treatment time prolonged.
Physiological Effects of Low Frequency Currents

1. Effect on body tissues: Tissues contain fluids, which contain ions and thus are good
conductor of electricity. Current passing through the body tissues consists a two-way
migration of ions and the conductivity of different body tissues varies according to the
amount of fluid they contain. Muscle is having good blood supply and so is a good
conductor while fat is a poor conductor. The epidermis has a high resistance and thus
is a bad conductor. So for having better conduction of electricity, we use some media
like water or gel to lower the resistance for treatment purposes.
2. Stimulation of sensory nerves: Faradic current: When applying a faradic type current
mild prickling sensation is felt due to stimulation of sensory nerves. This stimulation
is not very marked because the stimuli are of fairly short-duration.
Interrupted Galvanic Current: This also stimulates sensory nerves and results in stabbing
or burning sensation. This stimulation is very marked because the stimuli are long-
duration impulses.
When sensory nerve is stimulated either by faradic or interrupted galvanic current, it
also produces reflex vasodilatation of superficial blood vessels. So slight erythema is
seen, this vasodilatation is limited up to superficial area only.
3. Stimulation of motor nerves by faradic current: Faradic current stimulates the

motor nerves and if it is of sufficient intensity, it stimulates muscle to which the
nerve supplies. The contraction produced is thus a tetanic contraction because
stimuli are repeated 50 times per second. This type of contraction if maintained for
a longer period may result in muscle fatigue. So to avoid this, current is commonly
surged to allow muscle relaxation. When the current is surged the contraction
gradually increases and decreases in strength, in a manner similar to a voluntary
contraction.
By Galvanic Current: If we stimulate motor nerve with interrupted galvanic current it
also produces muscle contraction but because of frequent repeated stimuli it produces
muscle twitch followed by immediate relaxation. Effect of this type of current is thus
less beneficial on the muscles.
4. Effect on muscle contraction: Electrical stimulation of motor nerves causes muscle
contraction and results in changes similar to those associated with voluntary
contraction. These contractions help in regaining the properties of muscles as such and
also helps in:
i. Increasing metabolism: The contraction and relaxation of muscles results in
pumping action on the blood vessels within the muscles and around it.
This pumping action provides more blood supply to the muscles and also results
in increased demand and supply of oxygen and nutrition.
ii. Removal of waste products: If the muscle contraction and relaxation is sufficient
enough to cause pumping effect on venous and lymphatic vessels it results in
removal of waste products.
5. Stimulation of denervated muscle: For contraction of denervated muscle the impulse
more than 1 ms is required. This impulse is usually is not tolerable by the patient
for treatment purposes. Thus faradic type current is not used for stimulation of
denervated muscle. Interrupted direct current is used for stimulation of denervated
muscle therapeutically, when it is of sufficient intensity and duration. Effective
contraction is obtained only when current rises slowly rather than rising suddenly.
An impulse of 100 ms is the shortest impulse for satisfactory treatment of denervated
muscle. So, intensity and duration of the impulse are important factors for stimulation
of denervated muscle.
6. Chemical effects following stimulation: Chemical effects are produced at the
electrodes due to passing of direct current through the electrolyte. It results in
formation and accumulation of chemicals at the electrode site resulting in chemical
or electrolytic burn. The risk is comparatively less with an intermittent current than
with a direct current. When an alternative current is used, chemicals formed during
one phase are neutralized during the next phase as the ions move one way during
one phase and in reverse direction during the other phase. In a condition, where the
two phases are equal, chemicals formed during one phase are neutralized during the
next phase.
Methods of treatment
Treatment of Patients condition

1. Median nerve stimulation
2. Ulnar nerve stimulation
3. Radial nerve stimulation
4. Erbs paralysis
5. Facial nerve stimulation
6. Deltoid inhibition
7. Quadriceps inhibition
8. Lateral popliteal nerve stimulation
9. Faradism under pressure
10. Faradic foot bath.
Common Motor Points
PROFORMA FOR PATIENTS ASSESSMENT

1. Receiving the patient:
Good morning, I am a Physiotherapist and I am going to treat you. Please, cooperate
with me during the treatment and wait until I go through your case sheet.
2. History taking or going through the case sheet:
i. Name
ii. Fathers and Mothers name
iii. Age
iv. Sex
v. Occupation
vi. Address: Correspondence and permanent
Chief complaints:
i. History of present illness
ii. History of past illness
iii. Family history
iv. Social and occupational history
v. Treatment history
vi. Prognosis of the treatment
vii. Investigations
Hematological tests
Radiological testsX-rays, MRI scan, etc.
Others.
3. Checking for general contraindications:
i. Hyperpyrexia/Fever
ii. Hypertension
iii. Anemia
iv. Severe renal and cardiac failure
v. Deep X-ray and cobalt therapy

vi. Epileptic patients
vii. Noncooperative patients
viii. Mentally-retarded patients
ix. Very poor general condition of the patient, etc.
4. Checking for local contraindications:
i. Open wounds ii. Very recent fractures
iii. Skin grafts iv. Severe edema
v. Hairy surface vi. Acute inflammation
vii. Metal in the part viii. Malignant growth
ix. Hypersensitive skin x. Loss of sensation, etc.
5. Preparation of trays:
i. Skin resistance lowering tray
ii. Treatment tray
Skin Resistance Lowering Tray

1. Saline water 2. Soap
3. Cotton 4. Vaseline
5. Towels, etc.
Treatment Tray
1. Mackintosh
2. Lint pads
3. Pad or plate electrodes and pen electrode
4. Leads
5. Straps
6. Cotton
7. Powder
8. Gel, etc.
Preparation of treatment tray

1. Mackintosh: The mackintosh is to be kept under the patients treatment part to prevent
earth shock and to prevent dripping of water.
2. Lint pad: The lint pad is made up of lint cloth and it is used to prevent accumulation
of chemicals in the tissues formed during the treatment which if not prevented leads
to burn. It must be in 8 or 16 layers. More the layers of lint pad, less the chance of
accumulation of chemicals, less the chance of burn.
To stimulate more number of motor points, two different electrodes covered with
lint pads are used. If stimulation of individual muscle is required, pen electrode is used
(Active) (Fig. 2.16).
Always to use indifferent pad proximally (nerve trunk or plexus) and active pad
distally (individual muscle).
Fig. 2.16: Treatment tray
Active pad: It is the place where the electrons enter the circuit. It is smaller than the
indifferent pad always. It should be placed on the motor point distally (Pen electrode).
Indifferent pad: It is the place where electrons leave the circuit. It is placed proximally.
This helps to complete the circuit.
3. Electrodes: Electrodes could be of pad or plate type or pen type. Pad or plate electrodes
are kept in between the lint pads for even distribution of current. The edges of plate
electrode should be blunt. It should be smaller than the lint pad so that it cannot come
in contact with the skin. Pen electrode is used for smaller muscles or for specific motor
points.
4. Leads: Used to connect the electrodes with the stimulator.
5. Straps: Usually rubber straps are used. It should be placed over the pad. It should be
fixed with the help of jaconet piece.
6. Cotton: Used to prevent dripping of water and for cleaning the surface.
7. Powder: Used to apply over the skin if there is any redness after the treatment. Redness
occurs due to erythema. It gives soothening effect.
8. Gel: Used for pad electrodes where lint pads are not used. Gel is used for proper contact
of electrodes with the patients surface.
Preparation of skin resistance lowering tray

1. Saline water: Prepared by adding the pinch of salt to the bowl of water. The aim of
preparing saline water is to prepare more ions so that minimum amount of current
that is enough to get the brisk contraction. If we use more than 1% saline there will
be lowering of ions and less amount of current passes since there will be restriction of
ions.
2. Soap: It is used for cleaning the part to be treated to remove dirt, dust or sebum, etc.
thus lowering the skin resistance (Fig. 2.17).
3. Cotton: It is used for cleaning the surface.
Fig. 2.17: Skin resistance lowering tray
4. Vaseline: It is applied over scar tissue. It prevents the concentration of more current on
the scar tissue.
5. Towels: Towels are used for covering the body part. Neat and clean towels should be
used every time.
Lowering skin resistance: By removing dust particles, sebum or sweat, skin resistance
can be lowered. In the presence of all these dust particles, sebum or sweat greater intensity
of current is required to get the contraction. It provides some resistance to the passage of
current.
6. Preparation of apparatus:
i. Check whether all the knobs are at zero.
ii. Checking the pins of the plug and check whether the switch is turned off.
iii. Check the insulation of the wire.
iv. Check whether the switch in the stimulator is working.
v. Check whether fuse is present in the apparatus; see that it is not blown out.
vi. Check whether hand switch for patients use is intact and is working.
7. Correct positioning of the patient:
i. Position the patient in such a way that it is comfortable to the patient.
ii. Part to be treated must be exposed and should be at adequate distance from the
modality.
8. Correct positioning of Physiotherapist:
i. Position of Physiotherapist should also be comfortable so that he/she may not get
tired after the treatment.
ii. Position should be such that it provides maximum accessibility to the treatment
part and to the modality.
9. Checking of apparatus: Self test to be done.
i. Apparatus must be checked once in front of the patient.
ii. Place the electrodes on yourself on palmar or dorsal aspect of hand or forearm.
iii. Switch on the apparatus and gradually increase the current.

iv. Explain the patient the feel of the current.
v. This will increase the confidence of the patient and will reduce its apprehension.
10. Correct placing of pads and electrodes.
11. Instructions to the patient:
I am going to start the treatment.
i. Be relaxed.
ii. Do not touch anything around you.
iii. Do not pull the leads.
iv. Do not touch the walls or ground.
v. If you feel uneasy switch off from the patients switch.
12. Regulating the current:
i. Gradually increase the current.
ii. Keep talking with the patient about the feel of the current.
iii. Tell him to inform you immediately about any inconvenience, discomfort or
burning.
13. Palpating tendon: Feel the contraction by palpating the tendon.
14. Selection of current:
i. Faradic current
ii. Galvanic current
iii. Other.
15. Selection of pulse, frequency, duration and treatment time.
16. Treatment.
17. Explanation to the patient:
i. Explain the patient the advantages of the treatment
ii. Explain the patient the course or duration of the treatment
iii. Explain the patient the dos and donts in home and otherwise.
MEDIAN NERVE STIMULATION

Good morning, I am a Physiotherapist and going to treat you. Please, cooperate with
me during the treatment and wait until I go through your case sheet.
Name
Fathers and Mothers name
Age
Sex
Occupation
Address: Correspondence and permanent
Chief complaints
History
History of any previous treatment taken.
3. Examination:
To the examiner
Side: Right or left
Site.
4. Checking for any general and local contraindications:
Fever
Hypertension
General condition of the body
Open wound
Hypersensitive skin
Metal in the tissue or in surrounding
Loss of sensation, etc.
5. Course of Nerve: The median nerve arises in the axilla from the medial and lateral
cords of brachial plexus with root values C5, C6, C7, C8, and T1. It supplies the
following muscles:
Pronator teres
Flexor carpi radialis
Palmaris longus
Flexor digitorum superficialis
Flexor digitorum profundus
Flexor pollicis longus
Pronator quadratus
Abductor pollicis
Flexor pollicis
Opponens pollicis
1st and 2nd Lumbricals.
It runs down in front of the elbow and supplies muscular branches in the forearm and
enters the palm deep to the flexor retinaculum of the wrist. Its main sensory supply is to
thumb, index, middle and radial half of ring finger.
Indications:
Injury at the level of elbow.
Cause: Supracondylar fracture
Dislocation of elbow joint.
Clinical Features:
All the muscles are paralyzed supplied by the nerve.
Injury at the wrist level:
Cause: Glass cut injury
Carpal tunnel:
Dislocated lunate bone
Chronic compression by swelling in the tunnel
Compound palmar ganglion.
Clinical features: Hand muscles supplied by the nerve are paralyzed.
Deformity:
1. Pointing index finger: because of paralysis of long flexor tendons of index finger.
2. Simian hand or Ape thumb deformityOpponens and short flexor paralysis.
3. Inability of flex the IP of thumb due to paralysis of FPL.
4. Opponens palsy: To oppose thumb to touch tip of other fingers.
5. Paralysis of abductor pollicis brevis
6. Sensory signs: Loss of sensation in the thumb, index, middle and radial half of ring
finger.
6. Treatment:
Preparation of trays
Preparation of apparatus
Position of the patient: The patient is made to sit in a wooden chair, provided
with back rest, he places his hand on the table with arms abducted and forearm
supinated and elbow semiextended.
Position of therapist: Walk standing
Checking of local contraindications
Reducing skin resistance
Checking apparatus (self test)
Correct placing of pads:
For forearm muscles:
Inactive: Over medial epicondyle of humerus
Active: Over the motor point
For hand muscles:
Inactive: Over wrist
Active: Over the motor point (Fig. 2.18).
Feel of current
Instruction to the patient to inform if any burning
Warning not to touch anything.
8. Regulating current.
Fig. 2.18: Median nerve stimulation

9. Palpating tendon: Feel the contraction by palpating the tendon

Gradually increasing the current
Keep talking with the patient about the feel of the current.
10. Home Programs:
Grasping and squeezing a rubber ball
Closing the hand then opening gently
Touching the tip of each finger in turn with tip of thumb making os
Touching the 2nd phalanx of each finger with tip of thumb
Piano playing movements of fingers with hand half-way between pronation and
supination
Abduction of wrist hand on block fingers flexed over edge push away weight by
abducting hand
Wrist machine forsupination and pronation when strong enough.
Picking up and putting down small objects, balls, dice, marbles, coins held by fingers,
also exercises with sand tray.
ULNAR NERVE STIMULATION

Name
Age
Sex
Occupation
Chief complaints
History
3. Examination:
To the examiner
Side: Right or left
Site.
Fever
Hypertension
Open wound
Hypersensitive skin
5. Indications of treatment:
i. Injury at the level of elbow region:
a. Traction injury resulting from violent valgus stress to the elbow

b. Avulsion fracture of medial epicondyle
c. Dislocation of elbow
d. Supracondylar fracture of humerus
e. Tardy or late ulnar neuritiscaused by increasing valgus deformity due to
nonunion of the fracture of lateral condyle of humerus.
ii. Injury at the level of wrist:
The ulnar nerve arises in the axilla from the medial cord of brachial plexus with
root values C7, C8, T1. It runs along the medial epicondyle of humerus at the
elbow to enter the forearm. It enters the palm by passing in front of the flexor
retinaculum through a fibrous canal. It supplies the following muscles of the
forearm and the intrinsic muscles of hand.
Flexor carpi ulnaris Flexor digitorum profundus
Adductor pollicis Flexor pollicis brevis
Ist dorsal interosseous Ist palmar interosseous
Abductor digit minimi Flexor digit minimi
Opponens digit minimi Third and fourth lumbricals
Clinical features:
All the muscles are paralyzed. When there is injury at the elbowtypical ulnar
claw hand of ring and little fingers, wasting of hypothenar muscles and depression
in the interosseous spaces in dorsal aspect of the hand. Adduction of thumb is not
possible.
Sensory loss: confined to the little finger and medial half of the ring finger and the
ulnar border of the hand.
Injury at wrist:
Flexor carpi ulnaris, Flexor digitorum profundus usually escapes (Fig. 2.19).
6. Preparation of trays.
7. Preparation of apparatus.
Fig. 2.19: Patient with ulnar nerve injury

Fig. 2.20: Ulnar nerve stimulation
8. Positioning of patient: The patient is made to sit in a wooden chair, provided with back
rest, he places his hand on the table with arms abducted and forearm supinated and
elbows semiextended (Fig. 2.20).
9. Position of Physiotherapist: Walk standing by the side of the patient.
10. Reducing skin resistance.
11. Treatment:
Checking of apparatus
Correct placing of pads and electrodes.
For stimulating forearm muscles:
In active electrode: Over wrist/Over carpal bones
Active electrode: Over the motor point
For adductor pollicis and interossei: Stimulate on the dorsum of hand
Neuropraxia: Above the site of lesion
Axonotmesis/Neurotmesis: Below the site of lesion.
Feel of Current:
Faradic: Prickling
Galvanic: Stabbing
Instruction to inform if any burning
Warning not to touch anything
Regulating current
Palpating tendon
Winding up. Check the treated area after treatment.
Other special points: Comfort of the patient.
13. Selection of current:
Neuropraxia: Surged faradic
Axonotmesis/Neurotmesis: Interrupted galvanic current
14. Reason for procedure.

15. Home programs:
Finger parting and closing (hand in supination table).
Grasping a sheet of paper with both hand between thumb and its finger keeping
MCP flexed and IP extended.
Adult: Finger tips and thumb of both hands placed together fingers slightly
abducted thumb between abduction and adduction, bring the 4 finger tips close
together flexing the MCP and bring thumb tip into contact with index finger
exercises.
Finger stretching, hands pronated on table, fingers flexed, stretch each finger
forward in turn.
Hands side by side on table supinated approximation in succession tips of 2 little
finger, 2 ring, 2 middle, 2 index.
Place index and little finger in front of middle and ring fingers.
RADIAL NERVE STIMULATION

Name
Age
Sex
Occupation
Chief complaints
History
3. Examination:
To the examiner
Side: Right or left
Site.
Within 21 days FG Test
Duration =
After 21 days SD curve
4. Checking for any general and local contraindication:
Fever
Hypertension
Open wound
Hypersensitive skin
Loss of sensation.
5. Knowledge of Anatomy:
Course of Nerve: Radial nerve is formed from the posterior cord of brachial plexus in
the axilla with root values C5, C6, C7, C8 and T1. It winds around the mid shaft of
humerus in the spiral groove and give the posterior interosseous nerve just above the
elbow and continues as the superficial branch of radial nerve.
It supplies:
i. Triceps
ii. Anconeus
iii. Brachioradialis
iv. Extensor carpi radialis brevis
v. Extensor carpi radialis longus
vi. Extensor carpi ulnaris
vii. Extensor digitorum
viii. Supinator
ix. Extensor digiti minimi
x. Abductor pollicis longus
xi. Extensor pollicis brevis
xii. Extensor pollicis longus
xiii. Extensor indicis.
Level of lesion:
a. Axilla: Old type of crutch with T type support at the topinjury at this level all the
muscles are paralyzed.
b. HumerusSaturday night palsy or drunkard palsy
Tourniquet palsycompression of blood vessels and nerves
Chemical neuritis (Postinjection palsy).
c. Elbow:
Supracondylar fracture
Dislocation of head of radius
Surgical excision of the head of radius (accidentally)
Clinical features:
Motor:
Wrist drop depending upon the level
Finger drop of injury
Thumb drop
Paralysis at axilla: Active extension at the elbow is also affected with all the above.
Sensory: Small area in the dorsum of the hand over the metacarpal bones of the thumb
and index finger.
Skin resistance lowering tray
Treatment tray
8. Position of the patient:
The patient is made to sit in a wooden chair, provided with backrest; he places the
hand on the table with arms abducted and elbows flexed to a 90 degrees. The wrist is
supported with a pad to,
Keep the wrist in normal functional position

To prevent over stretching of paralyzed muscle
To eliminate gravity.
9. Position of the physiotherapist:
Walk/stride standing position by the side of the patient
Checking for local contraindication
Reducing skin resistance.
10. Treatment:
Placement of electrodes:
Inactive: Radial groove
Active: Over the motor points
Neuropraxia:
Indifferent electrode: Just above the site of lesion
Active electrode: Over the motor point.
Axonotmesis/Neurotmesis:
Indifferent electrode: Just below the site of lesion
Active electrode: Over the motor point.
11. Selection of Current:
Neuropraxia: Surged faradic current
Axonotmesis/Neurotmesis: Interrupted galvanic current 1030 contraction.
Feel of current:
Faradic current: Prickling sensation
Galvanic current: Stabbing sensation
Inform if any burning sensation
14. Palpating tendon.
15. Winding up.
16. Other special points: Comfort and consideration.
17. Splint: Dynamic cock up splint.
18. Home programs:
Active assisted exercise: With the other hand wrist extension is done.
Grasp and squeeze tennis ball.
Five finger exercise: Hand pronated to the table, finger flexed and raise each finger
separately and later altogether.
Finger parting and closing.
ERBS PARALYSIS
Good morning, I am a physiotherapist and going to treat you. Please, cooperate with

Name
Age
Sex
Occupation
Chief complaints
History
3. Examination:
To the examiner
Side: Right or left
Site.
Fever
Hypertension
Open wound
Hypersensitive skin
5. Knowledge of anatomy:
When there is injury at the level of Erbs point C5, C6 it causes paralysis of the deltoid,
supraspinatus, infraspinatus, biceps and brachialis muscle. The arms hang by the side
with shoulder in internal rotation, elbow in extension and the forearm pronated with
the palm facing backwards, the so called Policeman Tip position. The hand and finger
functions are preserved.
Causes:
1. Breech delivery
2. Undue separation of the head of the humerus.
8. Correct positioning of the patient.
Child: Sitting position with arm slightly abducted and forearm supinated
Infant: On the mothers lap resting on a pillow.
9. Correct position of Physiotherapist.
10. Checking of apparatus (self test)
11. Treatment:
Placement of electrodes:
Child: Inactive: Over the nape of the neck
Active: Over the motor point.
The inactive pad electrode can be tied on the dorsum of the Physiotherapists hand.
12. Selection of current: Surged faradic or interrupted galvanic current is used.
1 3. Explaining feel and purpose.

Inform if any burning
Not to touch anything.
17. Winding up: Check the treatment area.
18. Home program.
Exercises taught to the mother
(Abduction of the shoulder external rotation of the shoulder)
Splint: Aeroplane splint can be used.
FACIAL NERVE STIMULATION

Name
Age
Sex
Occupation
Chief complaints
History
3. Examination:
To the examiner
Side: Right or left
Site.
Fever
Hypertension
Open wound
Hypersensitive skin
5. Knowledge of anatomy:
Bells palsy: This is the lower motor neuron lesion of the facial nerve and resultant
paralysis of the muscles that it supplies.
Course of the nerve: It starts from seventh cranial nerve nucleus. It is situated in the
ventral part of tegmentum of pons, rounds VI nucleus along its course expands to
form geniculate ganglion, it gives a branch to stapedius muscle, a branch supplying

anterior 2/3rd of tongue. Emerging from stylomastoid foramen it enters the parotid
gland and divides into:
Temporal
Zygomatic
Mandibular
Buccal
Cervical branches.
Muscles supplied:
1. Occipitofrontalis
2. Orbicularis oculi
3. Corrugator and procerus
4. Zygomaticus major and minor
5. Levator anguli oris
6. Levator labii superioris
7. Buccinator
8. Orbicularis oris
9. Risorius
10. Mentalis
11. Depressor anguli oris, depressor labii inferioris.
Causes:
1. Idiopathic
2. Exposure to chill weather
3. Fracture of mandible
4. Fracture of mastoid process
5. Dislocation of temporomandibular joint
6. Middle ear infection
7. Anesthesia during middle ear surgery
8. Trauma to jaw, parotid region
9. Cerebellopontine angle tumors
10. Hemorrhage at the site of the nucleus of the nerve.
Clinical features:
1. Bells phenomenon.
2. Loss of facial expression:
Receiving the patient
Knowing details of condition
Preparation of apparatus
Preparation and position of the patient: supine lying position with the hair duly
tied up (Fig. 2.21) and eyes closed, ask the patient to wash his face before treatment.
Position of therapist: Stride/walk standing position at the side of the patient.
Acne
Tooth clips
Eye infections
Hairy surface
Fig. 2.21: Facial nerve stimulation
Mouth ulcers
Mumps, measles, etc.
7. Checking of apparatus.
8. Correct placing of electrodes:
Inactive: Over the nape of neck
Feel of current
Inform if any burning
10. Treatment:
Selection of current:
For the muscles: Interrupted galvanic
For the nerve trunk: Surged faradic
12. Winding up.
13. Home programs:
Look surprised and then Frown.
Smile, grin, say O
Say a, e, i, o, u
Squeeze eyes closed then make wide open
Hold straw in mouth, suck and blow
Whistle.
Advice:
1. Avoid intake of cold substances
2. Cover up the head and face with a scarf
3. Avoid taking in hot substances when there is sensory loss in anterior 2/3rd of
tongue.
DELTOID INHIBITION
Name
Age
Sex
Occupation
Chief complaints
History
3. Examination:
To the examiner
Side: Right or left
Site.
Fever
Hypertension
Open wound
Hypersensitive skin
5. Condition:
Due to fear of pain, the patient keeps the deltoid muscle in contracted position. Abduction
and flexion of shoulder are limited.
Causes:
i. Fracture shaft of humerus
ii. Traumatic synovitis
iii. Any soft tissue injury around the shoulder joint
iv. Dislocation of shoulder, etc.
Deltoid is supplied by axillary or circumflex nerve (root value C5).
7. Preparation of the apparatus.
8. Position of the patient: The patient sitting in a chair with back support, the arm support.
9. Position of therapist: Stand by the side of the patient.
10. Checking of local contraindication.
11. Checking of apparatus (self test).
12. Placement of electrodes.
Inactive: Nape of neck (Pad electrode)

Active: Anterior, middle or posterior fibers of deltoid (Pen electrode).
1 3. Selection of current: Surged faradic current.
To inform any burning
15. Regulating currentn
16. Winding upn
17. Check the treatment area after treatment.
Faradic current is selected as it has the property of reeducation of muscles.
QUADRICEPS INHIBITION
Good morning: I am a physiotherapist and going to treat you. Please, cooperate with
Name
Age
Sex
Occupation
Chief complaints
History
3. Examination:
To the examiner
Side: Right or left
Site.
Fever
Hypertension
Open wound
Hypersensitive skin
5. Condition:
Due to fear of pain the patient cannot contract the quadriceps. He holds the muscle in
a tensed position; extension of knee is limited.
Causes:
Fracture shaft of femur
Menisectomy
Traumatic synovitis of knee

Surgical intervention
Soft tissue injury around the knee
Postoperative (i.e.) after arthroscopy.
6. Preparation of trays (2 pad electrodes).
8. Position of the patient: Half lying position:
The knee is flexed 2030 degree. The patient should be able to watch the contraction,
the knee is supported by placing a pillow.
9. Position of therapist: Stride standing by the side of the patient.
10. Checking the local contraindication.
12. Correct placing of pads and electrodes:
(Pad) In different: Upper 1/3rd of thigh (femoral triangle)
(Pad) Active: Kept over the lower part of thigh (so that it cover all the motor points
of quadriceps)
By using 2 pen electrodes
Vastus medialis and Vastus lateralis
Vastus lateralis and Rectus femoris
Vastus medialis and Rectus femoris.
1 3. Selection of Current: Surged Faradism, Duration10 min.
Explaining the feel and purpose
Instruction to inform any burning
16. Winding up.
17. Check the treatment area. If erythemaApply powder.
Surged faradic current is used; as the muscle is innervated and as the faradic current is
helpful in the reeducation of muscle.
LATERAL POPLITEAL NERVE INJURY

Name
Age
Sex
Occupation
Chief complaints
History
History of any previous treatment taken
3. Examination:
To the examiner
Side: Right or left
Site.
Fever
Hypertension
Open wound
Hypersensitive skin
5. Course of nerve: The lateral popliteal nerve arises at the upper part of the popliteal
fossa as the lateral division of sciatic nerve. It winds around the neck of the fibula to
enter the leg. It divides into two branches:
The superficial branch supplies:
Peroneus longus
Peroneus brevis.
The deep branch supplies:
Tibialis anterior
Extensor hallucis longus
Extensor digitorum longus
Extensor digitorum brevis.
Causes of injury:
Cuts and lacerations over the neck of fibula
Fracture neck of fibula associated with fracture lateral tibial condyle as in abduction
injuries to the knee
Traction injury due to adduction violence of knee associated with medial tibial
condyle fracture.
Clinical features:
Foot drop
Loss of sensation in the outer aspect of the leg and dorsum of the foot.
8. Position of patient: Half lying position with pillow under the leg and sand bag placed
under the foot.
9. Position of therapist: Walk standing/stride standing.
11. Placement of pads:
Inactive: Neck of fibula.

Explaining the feel and purpose
15. Winding up.
16. Home programs:
Foot drop splint to be used
Placing the foot over edge of plinth, dorsiflexion and plantarflexion is advised
Also in sitting legs crossed dorsiflexion and plantar is advised.
FARADISM UNDER PRESSURE

Name
Age
Sex
Occupation
Chief complaints
History
3. Examination:
To the examiner
Side: Right or left
Site.
Fever
Hypertension
Open wound
Hypersensitive skin
5. Purpose:
Electrical stimulation of the muscles that generally acts as the muscle pump may be
combined with compression and elevation of the limb to increase venous and lymphatic
return and so relieve edema, especially when treated with faradic type current.
Indications:
Soft tissue injury of the extremities
Gravitational edema
Lymphoedema
Post phlebitis syndrome
Varicose ulcers, etc.
6. Preparation of trays (Include crepe bandage)
7. Preparation of apparatus
8. Position of the patient:
Upper limb: The patient is made to sit in a chair with support, the arm is slightly
abducted and forearm supinated with palm facing upwards. The whole limb should
be placed in elevation. So that gravity assists the venous and lymphatic return.
9. Position of the therapist:
By the side of the patient walk/stride standing
Checking of local contraindication
1 0. Checking of apparatus (Self-test).
11. Placement of pads and electrodes.
Upper limb: Flexor aspects of arm and forearm
Lower limb: Active electrode over: Calf muscles
Inactive electrode over: Neck of fibula
Fix the pads in position firmly, with straps, if necessary test the contraction produced.
Adjust the pads as necessary. Then apply an elastic bandage, starting distally. It should
be firm but not too tight, avoid gaps between the turns of the bandage.
Explaining feel and purpose
13. Selection of current: Surged faradic current as it helps in increasing the venous and
lymphatic return.
15. Winding up.
16. Checking the treatment part.
FARADIC FOOT BATH

Name
Age
Sex
Occupation
Chief complaints
History of illness: Present or past
3. Examination:
To the examiner
Side: Right or left
Site.
Fever
Hypertension
Open wound
Hypersensitive skin
Also,
a. Infection of nails
b. Recent metatarsal fracture
c. Eczema or fungal infection
d. Crack foot
e. Open-unhealed wounds.
5. Indications:
Flat foot (Pes Planus)
Chronic retrocalcaneal bursitis
March fracture
Potts fracture
Metatarsalgia
Plantar fascitis
Plantar digital neuritis
Calcaneal spur
Sudecks atrophy
Hallux valgus
Hallux rigidus
Osteochondritis
Rheumatoid arthritis of foot
Poor musculature of arch of foot.
6. Preparation of trays: Only treatment tray, skin resistance lowering tray is not needed
patient should be asked to wash his foot before the treatment.
Treatment tray:
Lint pads
Mackintosh
Tray with saline/tap water
Straps
Pad electrode and pen electrode
Leads
Vaseline
Salt
Therapeutic electrical stimulator
Wooden footstool.
8. Positioning of the patient: Patient sitting over the wooden stool. Foot is placed in treatment
tray kept over the spread Mackintosh. Hip and knee are flexed to about 90 degrees. Patient
is asked to hold hip knee firmly to maintain contact by using body weight. Place the foot in
a bath containing enough warm water to cover the toes (Fig. 2.22).
Fig. 2.22: Faradic foot bath
9. Position of Physiotherapist: The physiotherapist should position himself in such a

way that she/he does not get entangled and he must be free to reach the patient and
machine. Sitting on stool and treating the patient is ideal. Sit on the stool in front of
patient at the controls of the machine and at the same time observe the muscle contrac-
tion.
10. Checking of apparatus: Self test to be done under water.
11. Correct placing of pads and electrode:
Lumbricals: Two electrodes placed transversaly across the bottom of the bath, one
under the heel and other obliquely under the metatarsal heads.
Plantar interossei: Place one electrode on each side of the foot at the level of meta-
tarsal heads
Abductor hallucis longus.
COMMON MOTOR POINTS (Figs 2.23 to 2.28)
Fig. 2.23: Motor points of the anterior aspect of the right arm
Fig. 2.24: Motor points of the posterior aspect of the right arm
Fig. 2.25: Motor points of the anterior aspect of the right leg
Fig. 2.26: Motor points of the posterior aspect of the right

Fig. 2.27: Motor points of the muscles supplied by the facial nerve
Fig. 2.28: Motor points of the back
12. Instruction to the patient

Warning Dont to touch anything.
13. Current used: Faradic current
Feel: Prickling sensation
Purpose: The muscles are innervated and one of the therapeutic effects of faradic
current is reeducation of the muscle action.
15. Palpating tendonAbductor hallucis is palpable.
16. Check the treatment part after treatment.
17. Home programs:

Walking on medial and lateral border of foot
MCR slipper to be worn
Walking on beach, pebble board
Rolling the towel with toes
Spreading of toes
Picking up of marbles with toes.
STRENGTH DURATION CURVE
Strength duration/Intensity duration curve shows the relationship between the magnitude
of the change of stimulus and the duration of the stimulus. The curve provides valuable
information regarding the state of excitability of nerve lesion. It should be done only after
21 days following nerve injury.
Wallerian degeneration: Nerve degenerates proximally to nearest node of Ranvier and
distally throughout whole length. Debris is cleared by macrophagic activity. Process takes
up to 21 days to complete and is a preparation for regeneration.
Nerve regeneration
1. Regeneration of axons send out many branches one of which becomes myelinated and
continues to grow down the neural tube.
2. Growth rate approximately 1 mm per day.
It occurs unevenly throughout the regeneration period being initially faster.
Factor influencing rate of regeneration

1. Age of the patient Faster in younger age group
2. Site of lesion Faster when lesion is more proximal to spinal cord.
3. Nature of lesion Faster following spontaneous regeneration than following
nerve suture.
Types of Injury
Seddons classification of injury
Neuropraxia:
Loss of conduction without degeneration
Nerve conduction possible below lesion
Sensory part frequently least affected than motor.
Axonotmesis:
Disruption of axon, but nerve sheath intact
Wallerian degeneration is followed by axons regrowing to own end organs.
Neurotmesis:
Disruption of axon and nerve sheath.
Surgery required approximating nerve sheaths and enabling growing axon to

reach correct end organ.
I. PART:
1. Receiving the patient (as in proforma)
2. Knowledge of condition
3. Preparation of trays (as described earlier)
4. Preparation of apparatusDiagnostic electrical stimulator to be used.
II. PART:
1. Positioning of the patient
2. Position of Physiotherapist
3. Checking for local contraindication (as described earlier)
4. Reducing skin resistance (as described earlier).
III. PART:
1. Checking of apparatus
2. Correct placing of pads and electrodes (depending upon the nerve)
Instructions to the patient:
Feel of current
Instruction to inform if any burning occurs
Warning not to touch anything
Regulating currentInterrupted galvanic current
Palpating tendon
Winding up.
Other special points:
Diagnostic stimulator to be used
Interrupted galvanic current indicated
Start with longer duration (from 100/300 ms)
Select small muscle or select a muscle, which has distinguished action, compare
with 3 muscles.
For Radial Nerve - Extensor indicis
For Median Nerve - Abductor pollicis brevis
For Ulnar Nerve - Abductor pollicis
For Lateral Popliteal Nerve - Peroneus longus
Shape of the Curve

Normal innervation
When all the nerve fibers supplying the muscles are intact, the strength duration curve has a
shape characteristic of normally innervated muscle (Figs 2.29A and B). The curve is of this
typical shape because the same strength of stimulus is required to produce a response with
all the impulses of longer duration, while those of shorter duration require an increase in
the strengths of the stimulus each time the duration is reduced.
Figs 2.29A and B: Normally innervated muscle: (A) In constant current; (B) In constant voltage
Complete Denervation
When all the nerve fibers supplying a muscle have degenerated, the strength duration
produced is characteristic of complete denervation. For all impulses with duration of 100 ms
or less the strength of the stimulus must be increased each time the duration is reduced and
no response is obtained to impulses of very short duration. So that the curve rises steeply
and is further to the right than that of a normally innervated muscle (Figs 2.30A and B).
Figs 2.30A and B: Complete denervated muscle: (A) In constant current; (B) In constant voltage
Partial Denervation
1. As impulses shorteneddenervated fibers respond less readily. So that a stronger
stimulation is required.
2. With impulse of shorter durationinnervated fibers responses (Fig. 2.31).
When some of the nerve fibers supplying a muscle have degenerated while others are
intact, the characteristic curve obtained clearly indicates partial denervation. The right
Fig. 2.31: Partially denervated muscle
hand part of the curve clearly resembles that of denervated muscle, the left hand part that
of innervated muscle, and a kink is seen at the point where the two parts meet.
Rheobase
The rheobase is the smallest current that produces a muscle contraction if the stimulus
is of infinite duration. In practice an impulse of 100 ms (0.1 s) is used. In denervation,
the rheobase may be less than that of innervated muscle and often rises as reinnervation
commences. The rheobase varies considerably in various muscles and according to the
skin resistance and temperature of the part. The rise of rheobase may be due to fibrosis of
the muscle.
Chronaxie
The chronaxie is the duration of shortest impulse that will produce a response with a
current of double the rheobase. The chronaxie of the innervated muscle is appreciably less
than that of denervated muscle, the former being less and the latter more than 1 ms if the
constant-voltage stimulator is used. With the constant-current stimulator the values are
higher, but bear a similar relationship to each other. As practically seen the chronaxie of a
muscle with 25% of its fibers innervated would be the same as that of a complete denervated
muscle. Thus, chronaxie is not a satisfactory method of testing electrical reactions as partial
denervation is not clearly shown.
Faradic and IDC Tests

The faradic type current provides impulses with duration of 0.11 ms and a frequency
of 50100 Hz. These cause a tetanic contraction of innervated muscles, but with a faradic
coil it is difficult or impossible to elicit a response from denervated muscle owing to the
short duration of the stimuli. However, with modern stimulators a response can usually
be obtained from denervated muscles with impulses of this duration because of greater
output and more tolerable form of current being produced than that from older device.
Interrupted direct current was used in impulses with duration of approximately 100
ms, repeated 20 times per minute. These usually produce a brisk contraction of innervated
muscle fibers, but a sluggish contraction of denervated fibers. Innervated muscles may
respond sluggishly if the temperature is below normal, while the contraction of denervated
muscle becomes brisker as its temperature rises.
Iontophoresis
Iontophoresis is a therapeutic technique, which involves the introduction of ions into the
body tissue through the patients skin. The basic principle is to place the ion under an elec-
trode with the same charge, i.e. negative ion placed under cathode and positive ion placed
under anode.
This technique is also known as technique of ion transfer into the body tissues by
using electrical current as a driving force (LeDuc, 1903).
The electrode under which ions are placed, is therefore called active electrode. A
constant direct current is used for propelling the ions into the patients body tissues. Direct
current ensures unidirectional flow of ions that is why only direct current is used and
alternative current cannot be used.
Iontophoresis has several advantages therapeutically such as being painless, sterile
and noninvasive method to introduce specific ions into the body tissues. The common
disadvantage associated with iontophoresis is chemical burn that usually occurs as a result
of direct current itself and not because of the ion being used in the treatment.
The quantity of the ions transferred into the tissues through iontophoresis is determined
by the intensity of the current or current density at the active electrode, the duration of
current flow and the concentration of ions at the active electrode or in the solution.
Type of electrode: The size and shape of electrode can cause a variation in current density
at the site of treatment. Less the size of electrode more will be the current density and more
ions will be transferred. Increasing the size of electrode will decrease the current intensity
thus reduces the concentration of ions at the electrode.
Current intensity and duration of treatment: Low intensity currents are more effective for
driving the ions into the body. The intensity may range from 512 mA. The treatment may
last for about 1520 minutes.
Methods of Treatment
1. Skin should be cleaned preferably with soap and hairy skin must be shaved.
2. Electrodes must have proper contact with the skin surface. Proper straps must be used
to keep the contact of electrodes.
3. In case the ions are used in the form of ointment, a layer of it is applied at the site to be
treated.
4. In case the ions are in the form of a solution, lint pad of absorbent material is used and
soaked in the ionic solution.
5. Appropriate ions are used for specific conditions.
6. The intensity of current and the duration of treatment must be regulated appropriately.
7. Precaution must be taken to prevent any burning. Use talcum powder if erythema is
seen after treatment.
Commonly used ions and their indications for use

Positive ions
1. Hydrocortisone: Used for its anti-inflammatory effects in conditions like rheumatoid
arthritis, tendinitis, bursitis, etc.
2. Calcium chloride: Calcium ions are used. It is found effective in stiff joint and post-
traumatic pains.
3. Zinc oxide: Used in cases of ulcers and open lesions, has property of healing.
4. Magnesium oxide: Used in arthritis, is an excellent muscle relaxant, good vasodilator
and mild analgesic.
5. Dexamethasone: Used for treating musculoskeletal inflammatory conditions.
Negative ions
1. Iodine: It is an effective sclerolytic agent, an excellent bacteriocidal and a fair vasodi-
lator. Effectively use for adherent scars, adhesive capsulitis.
2. Chlorine: Also an effective sclerolytic agent, useful for scar tissue, keloides and burns.
3. Salicylic acid: A general decongestant, sclerolytic and anti-inflammatory agent.
4. Sodium or potassium citrateEffective in rheumatoid arthritis.
Either +/ tap water: Used in the cases of hyperhydrosis (excessive sweating).
Glycopyrronium bromide is also used along with tap water in the cases hyperhydrosis.
Safety and precaution: Anticholinergic compounds have an atropine-like action,
therefore, patients may feel drying of mouth and throat. The patient may feel restriction of
general body sweating and therefore advised not to go for any strenuous activities, which
may require sweating.
Transcutaneous Electrical Nerve

Stimulation
Transcutaneous electrical nerve stimulation (tens) is the application of low frequency

current in the form of pulsed rectangular currents through surface electrodes on the
patients skin to reduce pain. A small battery operated machine is generally used to
generate current, which have specific stimulatory effect (Fig. 2.32).
The effect and use of TENS depends upon gate control theory and pain modulation.
Pain is an unpleasant disturbed sensation, which accompanies the activation of
nociceptors. Pain is a subjective phenomenon with multiple dimensions.
Nociceptors are the sensory receptors, which carries pain stimulus. Any physical, chemical,
thermal or mechanical stimulus like heat, cold or pressure activates these nociceptors. These
are free nerve endings found in all body tissues. They carry pain stimulus to the higher
centers. Once a nociceptor is stimulated, it releases a neuropeptide, which initiates the
electrical impulses along the afferent fibers toward the

spinal cord. These afferent fibers are of two types:
A Delta fibers: Fast conducting large diameter myelin-
ated fibers, which conducts with a velocity of 530
m/s.
C-fibers: Slow conducting small diameter nonmyelin-
ated fibers, which conducts with a velocity of 25
m/s.
First order or primary afferent fibers transmit
impulses from the sensory receptors to the dorsal
horn of the spinal cord. Second order afferent fiber
carry sensory impulses from the dorsal horn of the
spinal cord to the brain.
Fig. 2.32: TENS apparatus
First order neurons include A-alpha, A-beta,
A-delta and C-fibers. A-alpha and A-beta fibers are
characterized by having large diameter afferents and
A-delta and C-fibers are characterized by having small diameter afferents. The second
order afferents are nociceptive specific. A nociceptive neuron transmits pain signals. Its
cell body lies in the dorsal root ganglion. A-delta and C-fibers transmits the sensation of
pain. Fast pain is transmitted over the larger, faster-conducting A-delta afferent neurons
and originates from receptors located in the skin. Slow pain is transmitted by the C afferent
neurons and originates from both superficial (skin) and deeper (ligaments and muscle)
tissue. Most nociceptive second-order neurons ascend to higher centers along one of three
tracts: (1) Lateral spinothalamic tract, (2) Spinoreticular tract, and (3) Spinoencephalic
tract, with the remainder ascending along the spinocervical tract or as projections to the
cuneate and gracile nuclei of the medulla. Approximately 90% of the wide dynamic range
second-order afferents terminate in the thalamus.
Pain gate control: The pain gate theory was first postulated by Ron Melzack and Pat
Wall in 1965. This theory was later modified in 1982. Afferent input is mainly through
posterior root of the spinal cord and all afferent information must pass through synapses
in the substantia gelatinosa and nucleus proprius of the posterior horn. It is at this level
that the pain gate operates and presynaptic inhibition by TENS works.
Mechanism of pain gate control: Nociceptive afferent enters the spinal cord via the dorsal
root and make synapses either with interneuron or with second order neuron (called as
transmission cells or T cells) in the substantia gelatinosa in dorsal horn of spinal cord. The
second order neuron crosses the midline of the spinal cord and transmit information to the
higher centers via the lateral spinothalamic tract. These second order ascending neuron
synapse with third order neuron in the nuclei of thalamus. The third order neuron carries
the noxious stimulus to the cerebral cortex.
Modulation of transmission of pain can be achieved by altering the excitability of
this pain pathway. The excitability of this pathway can be altered by other neurons
(substantia gelatinosa) in the dorsal horn. The substantia gelatinosa (SG) cells have
inhibitory influence on the T cells. This mechanism is called as presynaptic inhibition.
Also the nociceptive afferent sends collaterals to the substantia gelatinosa (SG) which
inhibits the substantia gelatinosa cells when these nociceptive afferents are activated
these causes inhibition of substantia gelatinosa (SG) cell activity which will further
inhibit the mechanism of presynaptic inhibition thus allowing the nociceptive stimuli to
reach the higher centers.
Also low threshold large diameter mechanosensitive afferent have excitatory influence
on substantia gelatinosa (SG) cells. Their activation causes excitation of substantia
gelatinosa (SG) activity which in result causes increased presynaptic inhibition blocking
the transmission at T cells thus closes the gate for nociceptive stimuli to travel up to the
higher center. This is the site where the pain gate operates (Fig. 2.33).
In addition to these input to SG cells from peripheral afferent there are descending
influences on Transmission cells (T cells) which came principally from higher center such
as periaqueduct gray matter PAG (midbrain) and raphe nucleus (medulla) these both have
excitatory influence on the substantia gelatinosa (SG) cells activity thus have ability to
reduce pain transmission. These pathways are thought to exert their effect on Substantia
gelatinosa (SG) cells by release of neurotransmitters such as noradrenaline and 5-hydroxy
tryptamine.
Under normal conditions periaqueduct gray matter (PAG) and raphe nucleus
are inhibited by neurons from other areas of the brain. During pain the inhibition on
periaqueduct gray matter (PAG) and raphe nucleus (RN) is removed by influence of the
limbic system thus allowing PAG and RN to exert its effect at substantia gelatinosa of
dorsal horn of the spinal cord.
The TENS stimulates the large diameter myelinated fibers as these are highly sensitive
to electrical stimulation and quickly conduct the electrical impulse to the spinal cord. The
A-delta and C-fibers are unable to pass the painful stimulus to spinal cord earlier than the
large fibers.
This mechanism by which the nociceptor fibers are prevented from passing on their
message to the spinal cord is called as presynaptic inhibition.
Types of TENS
1. High TENS: In this high frequency and low intensity electrical stimulation is applied.
The stimulation will cause impulse to be carried along with the large diameter afferent
fibers and produces presynaptic inhibition of transmission of nociceptive A-delta and
C-fibers at substantia gelatinosa of the pain gate.
Frequency 100150 Hz
Pulse width 100 and 500 ms
Intensity 1230 mA
2. Low TENS: In this low frequency and high intensity electrical pulses are applied, it
gives a sharp stimulus and like a muscle twitch. As the nociceptive stimulus is carried
toward the cerebrum, its passage through the midbrain will cause the periaqueductal
area of gray matter and raphe nucleus to interact to release the opiate-like substances
at cord level. The encephalins and endorphins released have the effect of blocking
forward transmission in the pain circuit.
Fig. 2.33: Mechanism of pain gate control

Frequency 15 Hz
Pulse width 100 and 500 ms
Intensity 30 mA or more
3. Burst TENS: In this high frequency, short pulse, high intensity electrical current is
used.
Burst TENS is a series of impulse repeated for 15 times per second. Each train
(burst) lasts for about 70 ms. The benefits for the Burst TENS are that it combines both
the conventional and acupuncture like TENS and thus provide pain relief by the both
routes.
Electrode placement: TENS electrode can be placed over
1. Area of greater intensity of pain.
2. Superficial nerve proximal to the site of pain.
3. To the appropriate dermatome.
4. To the nerve trunk trigger point.
A number of treatment methods may be used depending upon the severity of the
problem.
1. TENS can be used for a single daily treatment of 40 minutes duration.
2. Portable TENS can be used continuously for 24 hours.
3. TENS can be used in night, e.g. for the treatment of phantom limb pain.
Indications for Use

TENS can be used for the treatment of:
1. Chronic pain syndrome
2. Phantom limb pain
3. Reflex sympathetic dystrophy
4. Postoperative pain
5. Obstetric pain.
Dangers and Contraindications

1. Continuous application of high TENS may result in some electrolytic reaction below
the skin surface.
2. TENS is contraindicated in patients having cardiac pacemakers may be because of
possible interference with the frequency of pacemaker.
3. TENS should be avoided in first three months of pregnancy.
4. TENS should be avoided in hemorrhagic conditions.
5. TENS should be avoided over open wounds, carotid sinus, over the mouth, near eyes,
etc.
Microcurrent Electrical Neuromuscular

Stimulation
Microcurrent Electrical Neuromuscular Stimulation (MENS) commonly known as

Microcurrent therapy are extremely small pulsating currents (millionths of an ampere)
used to relieve pain and to heal soft tissues of the body. These currents are so small that the
patient rarely feels it. These currents are finely tuned to the level of the normal electrical
potentials which occurs at bodys own cellular level.
These electrical currents have a very close proximity of human bodys own internal
electrical potentials. Typically less than 600 microamps, there is no patient discomfort or
even sensation felt during application. These currents being more biologically compatible
than any other electrical stimulation device, have the ability to penetrate the cellas
opposed to passing over the cell by other stimulation devices. It works on Arndt-Schultz
Law which states that: Weak stimuli increases physiological activity and very strong
stimuli inhibit or abolish activity. The human body has the equivalent of electrical circuits
that play a very important role in healing.
Like Transcutaneous Electrical Nerve Stimulation (TENS), Microcurrents are capable
of decreasing or eliminating pain. In addition to the treatment of pain, Microcurrents also
appears to have a capacity for stimulating the healing process. Clinical observation clearly
shows that microcurrent therapy does more than just to block pain. Microcurrent therapy is
often recommended in cases involving soft tissue inflammation or muscle spasm. The various
modes of application, adjustable treatment variables and relatively few contraindications
make this the modality of choice or wave of the future for a large variety of clinical problems.
This subsensory current normalizes the ordinary activity taking place within the cell if
it has been injured or otherwise compromised. The external addition of microcurrent will
increase the production of ATP, protein synthesis, oxygenation, ion exchange, absorption
of nutrients, elimination of waste products and neutralizes the oscillating polarity of
deficient cells thus restoring the homeostasis.
The biologically sensitive stimulation effect of Microcurrent picks up where the bodys
own electrical current fails, as the human body must adhere to the natural law of electricity
which is: electricity must take path of least resistance. Therefore, its electrical current is
destined to move around an injury or defect, rather than through it. By normalizing cell
activity, inflammation is reduced while collagen producing cells are increased. Healthy
cell metabolism creates a healthy, pain free internal environment.
The various effects produced by Microcurrent Electrical Neuromuscular Stimulation
(MENS) are:
Reduce acute and chronic pain
Increase local blood circulation
Reduce swelling and inflammation
Improve soft tissue regeneration
Decrease muscular spasm
Prevent or retard the atrophy of muscular tissue
Reeducate nerves and muscles
Release muscle trigger points.
Medium Frequency
3 Currents
Medium frequency currents are the currents whose frequency falls between the range of
1000 to 10000 Hz. They are being used therapeutically due to their advantage of greater
penetration and with a higher tolerance and comfort over the low frequency current.
Rebox-type currents
Reboxtype currents are derived from a device called Rebox. It was developed in
Czechoslovakia in the 1970s. There is a point electrode and a hand held device. The point
electrode is made the negative pole. The device consists of a microammeter and earphone.
This system can be linked to a computer for display of graph of current. The current
produced consists of unipolar rectangular pulses of between 50 and 250 s at 3000Hz.
Russian Currents
Russian currents are evenly alternating currents with a frequency of 2500 Hz (between
200010000 Hz). These are applied with a series of separate bursts, i.e. polyphasic AC
waveforms (Fig. 3.1). There are thus 50 periods of 20 ms duration consisting of 10 ms burst
and 10 ms interval. Each 10 ms burst contains 25 cycles of alternating current, i.e. 50 phases
of 0.2 ms duration. These bursts reduces the total amount of current given to the patient
thus increases patients tolerance. The other factor affecting patients tolerance is the effect
of frequency on the patients tissue. Higher frequency current reduces the resistance to the
current flow again making this type of waveform comfortable enough that the patient may
tolerate with higher intensities. There are two basic waveforms which are used: A sine
wave and a square waveform with a fixed intrapulse interval.
Fig. 3.1: Russian currents

Interferential therapy
The principles of interferential therapy were first introduced by Ho Nemec (an Austrian
scientist). Interferential currents are also known as Nemecs currents. In this two medium
frequency currents are used to produce a low frequency effect. Since direct application of
faradic current results in pain due to high impedance of tissues, so to have a low frequency
effect two medium frequency currents are used. Out of these two medium frequency
currents one current is always of 4000 Hz because there is minimum impedance generated
by the tissues against this frequency current. The other current can be varied accordingly.
Basic principles of Interferential Therapy

The Interferential therapy depends
upon the principles of Interferential
effect of two medium frequency
currents crossing in the patients
tissues. The interference produced by
two currents in the tissues is called the
beat frequency. For example, let us
take two medium frequency currents,
current in circuit A = 4000 Hz and
circuit B = 3900 Hz. Where these two
currents are applied to the tissues,
at the point where the currents cross Fig. 3.2: Production of beat frequency by two
over, a new beat frequency current is medium frequency currents
set up whose amplitude is modulated
and the frequency of new current is
called beat frequency (interferential
current) and that is 100 Hz (Fig. 3.2).
By varying the frequency of the second channel relative to the constant frequency of
the first, this is possible to produce a range of beat frequencies deep in the patients tissues.
Thus, it is possible to produce any desired frequency in the range of 1250 Hz by varying
the frequency difference of the carrier currents. One of the major advantages by the use
of interferential therapy is that the effects are produced in the tissues where they are
required, without unnecessary or uncomfortable skin stimulation. The advantage of IFT is
that, it can be used for pain relief as well as for muscle stimulation. The main advantage is
that, patient cannot be given higher doses in low frequency therapy apparatus like faradic
stimulator. The skin resistance offered to the 4,000 cycles/second is very much less than the
resistance offered to the low frequency currents such as faradic currents. The principle of
reduction in pain is because of gate control theory and stimulated release of pain reducing
substances (endorphin and encephalin).
Definition and Terms Applied with Interferential Therapy

Interferential current is the resultant current produced when two or more alternating
currents are applied simultaneously at the point of intersection in a given medium.
Medium Frequency Currents 137
Impedance: Resistance, capacitance and inductance all these collectively form the impedance
of the circuit. This impedance is a type of resistance produced by the tissues against any
electrical stimulation of low frequency.
Impedance is denoted by Z.
Where, f = Frequency of current
C = Capacitance
Z = Impedance of tissues.
Phase: The current traveling from 0 to 180 is called to be in the same phase and the current
traveling from 180 to 360 is called to be in opposite phase, i.e. if current A is traveling to B and
C, then A to B it is called to be in same phase and from B to C it is called to be in opposite phase.
Wherever two waves of same frequency travel in same phase, then the peak of their
crest and trough coincide and the resultant wave has amplitude more than the original
amplitudes. But frequency will not change.
If two currents are traveling with little difference in their frequency then the amplitude
of the resultant wave will increase or decrease in regular cycle. This is called amplitude
modulation.
This amplitude modulation is denoted by the difference of two original frequencies
and is termed as beat frequency.
Modulation depth: Apart from frequency of modulation, the amplitude modulation is also
characterized by depth of modulation. The modulation will be between 0 and 100%.
Sweep frequency: Sweep frequency is the frequency which can be directly fed to the beat
frequency by the machine.
Electrodes: In interferential therapy, the flexible electrodes are used which are taped or bound
to skin by vacuum electrodes which use suction to maintain contact. Usually four electrodes
are used in interferential therapy, but two electrodes may be used in the treatment.
Balance: Electric current applied through the skin depends on the condition of electrode,
sponge and the skin. Hence when two currents are applied there may be unequal current
passing through each circuit. This occurs due to the unequal resistance encountered. In
order to compensate this situation the current in both the channels can be equalized.
Sweep: It is possible to change the frequency, between preset one and preset one plus
additional frequency, continuously in a prefixed pattern and time, is the sweep.
Spectrum: Interferential therapy (IFT) makes use of principle of Bernard of varying the
frequency to prevent accommodation.
Spectrum denotes the range of frequency during the treatment. In this range, all
frequencies are automatically transversed. The use of spectrum has the advantage that the
tissue does not adapt to a certain frequency and thus a given treatment can be performed
for a longer period and repeated more often.
1. Skin must be clean and clear before the start of the treatment.
2. The part of the body to be treated should be washed and if there is any skin lesion it
should be covered by applying petroleum jelly on it.
3. The electrodes should be placed in such a way that the crossing point of two currents
lie above or around the affected part.
4. The suitable frequency current should be given for different conditions.
5. Select the spectrum mode rectangular, triangular or trapezoidal as needed.
6. Select the base frequency and upper frequency, the difference between upper frequency
and base frequency would give the spectrum.
7. Increase the power gently and cautiously until the patient starts feeling the current. It
can be increased till the patient can tolerate.
8. The current in channel-I and channel-II are independently measured.
9. If there is difference in current in both the channels, this can be equalized by the balance
control provided for this purpose. Usually, this difference is caused due to difference
in resistance in the body where the two currents are passing.
10. Remember that in case of two electrodes there is current output available only in
channel (I) by the superimposition of the two channels internally.
11. After the treatment, adjust the intensity control to minimum.
12. Switch OFF the mains and disconnect the electrodes.
Advantages of Interferential Currents

1. The interferential currents do not produce any sensory nerve irritation, irrespective
of amplitude. Their application is free of any burning sensation on the skin surface as
is sometimes experienced with other low frequency currents which are disturbing to
current sensitive patients.
2. A medium frequency alternative current, it is high frequency and absence of direct
current properties, are the most suitable for treating deeper layers of tissues. It is
therefore most useful in treating tissues at a greater depth. For example, in muscles,
tendons, nerves, bursae and periosteum. Unlike galvanic which has more reaction in
the skin and subcutaneous tissues, IFT is harmless.
3. Resistance of skin is minimum while using frequencies in the range of 4,000 Hz, and
therefore higher doses can be given to the body without any discomfort to the skin.
4. The current can be localized more effectively in specific area. Extensive area can also
be covered.
Physiological Effects of Interferential Therapy

The physiological effects of interferential therapy depend upon:
1. Magnitude of the current
2. Type of mode usedRhythmic or constant
3. The frequency range used
4. Accuracy of electrode positioning.
The effects are:
1. Relief of pain: Relief of pain is an important physiological effect obtained by the use
of interferential therapy. The increase in local blood circulation due to the local
pumping effect of the stimulated muscles or the effect on autonomic nerves and thus
the blood vessels help removing the chemicals from the local area. Short duration
pulses at a frequency of 100 Hz may stimulate large diameter nerve fibers which
will have an effect on the pain gate in the posterior horn, and inhibit transmission
of small diameter nociceptive traffic. A frequency of 80100 Hz rhythmic is usually
chosen for this effect, as the problem of accommodation is reduced. In order to
selectively activate the descending pain suppression system, a frequency of 15 Hz is
required and the stimulation of small diameter fibers produced will eventually cause
the release of endogenous opiates (enkephalin and endorphin) at a spinal level. A
physiological blocking of nerve transmission is also postulated as a mechanism of
pain modulation produced by interferential therapy. It is thought that the maximum
frequency of transmission in C nerve fibers is 15 Hz and in A fibers is 40 Hz. The
application of frequencies higher than this maximum could block transmission along
these fibers altogether. Consideration should also be given to the effective aspects of
pain modulation, and there is probably a strong placebo effect associated in many
different countries claim good results in the modulation of both acute and chronic
pain syndromes.
2. Motor stimulation: Normal innervated muscles will be made to contract if interferential
frequencies between 1 and 100 Hz are used. The type of contraction depends on the
frequency of stimulation, as the shape and length of each individual stimulus is of a
muscle stimulating type. At low frequencies a twitch is produced, between 5 and 20
Hz a partial tetany, and from 30 to 100 Hz a tetanic contraction. A complete range
of all these types of muscle contraction can be seen when a rhythmical frequency of
1100 Hz is used. Muscle contraction is produced with little sensory stimulation, and
can be of deeply placed muscles, e.g. pelvic floor. Unfortunately, the patient is unable
to voluntarily contract with the current (unlike faradism), but this does not seem to
adversely affect the results. It is claimed that the rapid return of tune to the pelvic floor
when treated with interferential therapy is the result of stimulation of both the voluntary
and smooth muscle fibers; faradism can only stimulate the voluntary component.
3. Absorption of exudates: This is accelerated by a frequency of 110 Hz rhythmic, as a
rhythmical pumping action is produced by muscle contraction, and there is possible
an effect on the autonomic nerves which can affect the diameter of blood vessels, and
therefore the circulation. Both of these factors will help absorb exudates and thus
reduce swelling.
Treatment of patients condition

1. Relief of chronic pain
i. Low back pain
ii. Periarthritis shoulder
iii. Osteoarthritis knee
2. Absorption of exudates
3. Stress incontinence.

Good morning, a physiotherapist and I am going to treat you. Please, cooperate with
Name
Age
Sex
Occupation
Address: Correspondence and permanent.
Chief complaints:
History of present illness
History of past illness
Family history
Social and occupational history
Treatment history
Prognosis of the treatment
Investigations:
i. Hematological tests
ii. Radiological tests
X- rays, MRI scan, etc.
iii. Others.
Hyperpyrexia/Fever
Hypertension
Anemia
Severe renal and cardiac failure
Deep X-ray and cobalt therapy
Epileptic patients
Non cooperative patients
Mentally retarded patients
Very poor general condition of the patient.
Open wounds
Very recent fractures
Skin grafts
Severe edema
Hairy surface
Acute inflammation
Metal in the part
Malignant growth
Hypersensitive skin
Loss of sensation.
Treatment tray
Skin resistance lowering tray.
Treatment tray:
1. Mackintosh
2. Lint pads
3. Pad or plate electrodes and pen electroded
4. Leads
5. Straps
6. Cotton
7. Powder
8. Gel, etc.
Skin resistance lowering tray:
1. Saline water
2. Soap
3. Cotton
4. Vaseline
5. Towels, etc.
Preparation of treatment tray

1. Mackintosh: The Mackintosh is to be kept under the patients treatment part to prevent
earth shock and to prevent dripping of water.
2. Lint pads: The lint pad is made up of lint cloth, and it is used to prevent accumulation
of chemicals in the tissues formed during the treatment which if not prevented leads
to burn. It must be in 8 or 16 layers. More the layers of lint pad, less the chance of
accumulation of chemicals, less the chance of burn.
3. Electrodes: Electrodes could be of pad type or plate type. Pad or plate electrodes are kept
in between the lint pads for even distribution of current. The edges of plate electrodes
should be blunt. It should be smaller than the lint pad so that it cannot come in contact
with the skin.
4. Leads: Used to connect the electrodes with the stimulator.
5. Straps: Usually, rubber straps are used. It should be placed over the pad. It should be
fixed with the help of jaconet piece.
6. Cotton: Used to prevent dripping of water and for cleaning the surface.
7. Powder: Used to apply over the skin if there is any redness after the treatment. Redness
occurs due to erythema. It gives soothening effect.
8. Gel: Used for pad electrodes where lint pads are not used. Gel is used for proper contact
of electrodes with the patients surface.
Preparation of skin resistance lowering tray

1. Saline water: Prepared by adding the pinch of salt to the bowl of water. The aim of
preparing saline water is to prepare more ions so that minimum amount of current
that is enough to get the desired effects. If we use more than 1% saline there will be
lowering of ions and less amount of current passes since there will be restriction of
ions.
2. Soap: It is used for cleaning the part to be treated to remove dirt, dust or sebum, etc.
thus lowering the skin resistance (Fig. 3.3).
Fig. 3.3: Skin resistance lowering tray
3. Cotton: It is used for cleaning the surface.

4. Vaseline: It is applied over scar tissue. It prevents the concentration of more current on
the scar tissue.
5. Towels: Towels are used for covering the body part. Neat and clean towels should be
used every time.
Lowering skin resistance:
By removing dust particles, sebum or sweat, skin resistance can be lowered. In the
presence of all these dust particles, sebum or sweat greater intensity of current is
required to get the contraction. It provides some resistance to the passage of current.
Check whether all the knobs are at Zero.
Checking the pins of the plug and check whether the switch is turned off.
Check the insulation of the wire.
Check whether the switch in the stimulator is working.
Check whether fuse is present in the apparatus; see that it is not blown out.
Check whether hand switch for patients use is intact and is working.
Position the patient in such a way that it is comfortable to the patient.
Part to be treated must be exposed and should be at adequate distance from the
modality.
8. Correct positioning of Physiotherapist: Position of Physiotherapist should also be
comfortable so that he/she may not get tired after the treatment.
Position should be such that it provides maximum accessibility to the treatment

part and to the modality.
9. Correct placing of pads and electrodes.
I am going to start the treatment.
Be relaxed
Dont touch anything around you
Dont pull the leads
Dont touch the walls or ground
If you feel uneasy switch off from the patients switch.
Gradually increase the current
Keep talking with the patient about the feel of the current
Tell him to inform you immediately about any inconvenience, discomfort or
burning.
Explain the patient the advantages of the treatment
Explain the patient the course or duration of the treatment
Explain the patient the dos and donts in home and otherwise.
LOW BACK PAIN

Low back pain is characterized by pain which is present in the lower part of the back
region. As much as 80% of the industrial population and 60% of the general population
experience acute low back pain at some point of time in their life. Hence, low back pain is
a cause of great economic and clinical significance.
Etiology
In the majority of the patients, the common causes of low back pain are:
1. Idiopathic
2. Discogenic.
However, LBA could result from various other causes. It is therefore necessary to
identify and rule out the other causes of LBA before initiating physiotherapy.
Name
Age
Sex
Occupation
Chief complaints
Treatment history
Investigations:
X-rays, MRI scan, etc.
iii. Others.
Hyperpyrexia/Fever
Hypertension
Epileptic patients
Mentally retarded patients.
Open wounds
Hairy surface
Metal in the part
Malignant growth
Hypersensitive skin
Loss of sensation.
Treatment tray: Mackintosh, lint pads, pad or plate electrodes, leads, straps, cotton,
powder, gel, etc.
Skin resistance lowering tray: Saline water, soap, cotton, vaseline, towels, etc.
Check whether all the knobs are at zero
Checking the pins of the plug and check whether the switch is turned off
Check the insulation of the wire
Check whether the switch in the stimulator is working
Check whether fuse is present in the apparatus; see that it is not blown out
Patient must be comfortably placed preferably in lying (prone) position.
modality.
8. Correct positioning of Physiotherapist: Position of Physiotherapist should be in closed
vicinity of the patient and at appropriate reachable distance from the modality.
9. Correct placing of pads and electrodes: Four electrodes are placed in two pairs (sets) to be
placed diagonal to each other (Fig. 3.4).
Fig. 3.4: Interferential therapy (low backache)

Gradually increase the current
For relief of pain, a frequency of 80100 Hz rhythmic is used
Tell him to inform you immediately about any incon venience, discomfort or
burning.
Treatment
1. Rest and analgesics
2. Spinal extension exercises
3. Postural correction.
PERIARTHRITIS SHOULDER
Periarthritis shoulder is a condition characterized by pain and progressive limitation of
movements in the shoulder joint. In early stages, the pain is worst at night and the stiffness
is limited to abduction and external rotation of the shoulder. Later, the pain is present at
all times and all the movements of shoulder are severely limited. Often, there is a history
of preceeding trauma. The disease is common in diabetics.
Name
Age
Sex
Occupation
Chief complaints
Treatment history
Investigations
iii. Others.
Hyperpyrexia/fever
Hypertension
Epileptic patients
Mentally retarded patients.
Open wounds
Hairy surface
Metal in the part
Malignant growth
Hypersensitive skin
Loss of sensation.
Treatment traymackintosh, lint pads, pad or plate electrodes, leads, straps, cotton,
powder, gel, etc.
Skin resistance lowering traysaline water, soap, cotton, vaseline, towels, etc.
Check whether all the knobs are at Zero
Checking the pins of the plug and check whether the switch is turned off
Check the insulation of the wire
Check whether the switch in the stimulator is working
Check whether fuse is present in the apparatus; see that it is not blown out
7. Correct positioning of the patient: Sitting with back support, forearm rests over the
table with elbow flexed.
9. Correct placing of pads and electrodes: Four electrodes are placed in two pairs, placed
diagonal to each other.
Gradually increase the current. For relief of pain, a frequency of 80100 Hz rhythmic
is used
Tell him to inform you immediately about any inconvenience, discomfort or burning.
Explain the patient the dos and dont in home and otherwise.
Treatment
1. Make circle in air or against wall
2. Pendular exercises or Codmans exercises
3. Manipulation exercises.
OSTEOARTHRITIS KNEE
Osteoarthritis is a chronic degenerative disease of joints with exacerbations of acute inflam-
mation.
Incidence: Old age people (over the age of 50 years).
Classification
1. Primary: There is no obvious cause; primary osteoarthritis is due to wear and tear
changes occurring in old age due to weight bearing.
2. Secondary: There is a primary disease of the joint which leads to the degeneration of the
joint.
2. History taking or going through the case sheet.
3. Checking for general and local contraindications:
Hyperpyrexia/Fever
Metal in the part
Hypersensitive skin.
4. Loss of sensation.
5. Preparation of trays and apparatus.
Long sitting with back support and the affected leg is rest with a pillow below
the knee.
modality.
7. Correct positioning of Physiotherapist: Position of Physiotherapist should be

in closed vicinity of the patient and at appropriate reachable distance from the
modality.
8. Correct placing of pads and electrodes: Four electrodes are placed in two pairs,
placed diagonal to each other (Fig. 3.5).
Fig. 3.5: Interferential therapy (osteoarthritis knee)

Gradually increase the current. For relief of pain, a frequency of 80100 Hz
rhythmic is used
Tell him to inform you immediately about any inconvenience, discomfort or
burning.
Treatment
1. Static quadriceps exercises
2. Avoid cross sitting and prolonged standing.
ABSORPTION OF EXUDATES
The accumulation of exudates in skin and subcutaneous tissues is known as edema. It
could be due to heart failure, chronic venous inefficiency or due to nephrotic syndrome.
In heart failure excessive retention of salt and water leads to edema formation. In old age
there could be inferior vena cava obstruction or iliofemoral vein thrombosis leading to
chronic venous inefficiency and thus edema formation. In nephrotic syndrome, there is
more generalized form of edema which often affects face and arms.
1. Receiving the patient.

Treatment history
Investigations:
ii. Other tests.
3. Checking for general and local contraindications.
Patient must be comfortably placed preferably in supine lying position
modality.
7. Correct placing of pads and electrodes: Two pairs (sets) of electrodes are placed diag-
onal to each other.
8. Regulating the current: Frequency of 110 Hz rhythmic is used. The rhythmic mode
helps to produce pumping action over muscles and effects autonomic nerves which
leads to improving circulation.
Explain the patient the dos and donts in home and otherwise.
STRESS INCONTINENCE
Incontinence is rather a symptom than a disease. A common neurological cause of
incontinence is damage to cerebral cortex with damage to normal bladder inhibition. Stress
incontinence is common in females due to weakness of pelvic floor muscles.
Treatment history
Investigations.
3. Checking for general and local contraindications.

Patient must be comfortably placed in supine lying position with hip and knee
flexed.
modality.
6. Correct positioning of Physiotherapist: Position of physiotherapist should be in closed
7. Correct placing of pads and electrodes: The electrodes are placed over the lower
abdomen and over the inner thighs so as to produce good strong contraction of the
pelvic floor.
8. Regulating the current: Frequency of 1100 Hz rhythmic is used. At low frequencies
a twitch is produced, between 5 and 20 Hz a partial tetany and 30 to 100 Hz tetanic
contraction occurs. Muscle contraction is produced with little sensory stimulation. It is
claimed that the rapid return of the tone of pelvic floor muscles occurs when treated
with interferential therapy due to stimulation of both voluntary and smooth muscle
fibers. It has advantage over faradic current stimulation that faradic currents can only
stimulate voluntary components. Also, feel of current is much reduced in interferential
therapy.
High Frequency
4 Currents
Diathermy
Diathermy is a Greek word meaning through heating.
Diathermies are of following types:
1. Short wave diathermy
2. Microwave diathermy
3. Long wave diathermy.
Short wave diathermy

Short wave diathermy (Fig. 4.1) is the use of high frequency electromagnetic waves of the
frequency between 107 and 108Hz, and a wavelength between 30 and 3 m to generate heat
in the body tissues. It provides the deepest form of heat available to the physiotherapist.
Fig. 4.1: Short wave diathermy

The therapeutically used frequencies and wavelengths are 27.12 MHz and 11 m
(commonly).
The less common frequencies and wavelengths are 40.68 MHz and 7.5 m and 13.56 MHz
and 22 m.
Principles
It is not possible to produce high frequency currents by some mechanical device which
produces sufficient rapid movements. This type of current can only be produced by
discharging a condenser through an inductance of low ohmic resistance. If a current of
very high frequency is required, the capacitance and inductance should be small and if a
current of low frequency is required the capacitance and inductance should be large. This
is the mechanism of production of high frequency current.
Construction
The system consists of two circuits:
1. The machine circuit
2. The patient circuit.
The machine circuit

It consist of two transformers, whose primary coils are connected to source of AC. One is
a step-down transformer and its secondary coil supplies current to the filament heating
circuit of triode valve. The other is step-up transformer and connected to Anode Circuit.
Anode circuit carries the current produced by valve. Here it consists of triode valve and
oscillator circuit (Fig. 4.2). Oscillator circuit consists of condenser (XY) and inductor or
Fig. 4.2: Circuit for short wave diathermy

High Frequency Currents 153
oscillator coil (CD). Current of different frequencies are obtained by selecting suitable
condensers and inductances. To produce a current of high frequency the capacitance
and inductance used must be small and is made to charge and discharge repeatedly and
for obtaining this an oscillator is incorporated in to machine circuit along with valve
circuit.
Another coil AB lie close to oscillator coil (CD) and has one end connected to the grid
of the valve and other through grid leak (GL) resistance to the filament.
The patient circuit

The patient or resonator circuit is coupled to machine circuit by a inductor coil (EF) lying
close to oscillator coil (CD) and also consist variable condenser (HK) which is usually in
parallel to patient terminal. A matching high frequency current is produced in the reso-
nator circuit by electromagnetic induction. For this to happen the oscillator and resonator
circuits must be in resonance with each other, which requires that the product of induc-
tance and capacitance must be the same for both circuits.
Working
The AC from main passes through primary coils of the transformers and EMF is induced in
secondary coils. An EMF of 2025 volt is set-up in secondary coil of step-down transformer
and produces current through filament of the valve. The filament is heated and thermionic
emission takes place and current flows through valve.
The EMF of about 4000 volts is induced in the secondary coil of step-up transformer
and provided that anode of valve is positive and filament is negative, current flows in
anode circuit. The electrons flows from filament to anode through valve, through oscillator
coil in direction C to D and to transformer back to filament.
The electron form in CD will induce EMF in coil AB in direction that electrons
will move to grid of valve making it negative thus blocking the flow of electrons from
filament. This will lead to dying of current in anode circuit. This reduction in current
will lead to self-induced EMF. According to Lenz law, this EMF will try to prevent fall in
current by offering resistance to flow of current. This will charge condenser X (positive)
and Y (negative) polarity opposite to earlier one. Now when self-induced EMF totally
dies away, condensers again discharges through oscillator coil, but in opposite direction
(D to C).
Flow of current from D to C induce an EMF in AB such that electrons move from A to B
and grid loses its negative charge and anode current flows again. This sequence continues
and each time condenser charges and discharges through oscillator circuit leading to
production of high frequency current (SWD).
Grid Leak: When the current flows across the valve some electrons are caught on the grid
and grid leak is provided to enable these electrons to escape back to the filament.
The resonator coil (EF) lies within the varying magnetic field set-up around the oscil-
latory coil, so provided that two circuits are in resonance high frequency current is
induced in it. The current is similar to that in the oscillator circuit and is supplied to
patient.
Methods of Applications
The transfer of electrical energy to the patient tissues occurs either by electrostatic field or
by electromagnetic field. Therefore, two methods of applications are used:
1. Condenser/capacitor field method
2. Cable method.
When short wave diathermy is applied by the condenser field method, the electrodes
and the patients tissues form a capacitor. The capacitance of such a capacitor depends
upon:
1. The size of electrodes
2. The distance between the electrodes
3. The tissue between the electrodes.
When short wave diathermy is applied by the cable method, the cable and the patients
tissue forms an inductance, the value of which varies according to its arrangement.
Consequently, either the capacitance or inductance of the patients circuit is varied
at each treatment, and so a variable condenser is incorporated in the patients circuit to
compensate for this.
Tuning of the circuit: When the electrodes are arranged in position with the patients body,
the capacitance of the variable capacity is adjusted until the product of inductance and
capacitance of the resonator circuit is equal to that of the oscillator circuit. Thus, when
the oscillator and the resonator circuits are in tune with each other, there is transfer of
maximum energy into the patients body parts.
Indications of tuning are:
1. Indicator light on the equipment either comes on or changes its color, and attains a
specific color on tuning, generally blue.
2. An ammeter is used in the circuit to register the resonance between oscillator circuit
and resonator circuit by showing maximum deflection on turning the tuning knob.
3. A tube containing neon gas placed within the electric field between the electrodes or
the ends of the cable glows at maximum intensity when the circuits are in resonance.
Nowadays, modern machines have automatic resonator or tuners in it which automati-
cally searches for and selects the adjustment of the variable capacitor to ensure maximum
energy transfer to the patients body.
Capacitor field method

The electrodes are placed on each side of the part being treated. The electrodes are sepa-
rated by the skin by means of an insulating material. The electrodes act as the plates of the
capacitor, while the patients tissues together with the insulating material which separates
them from the electrodes for the dielectric.
When the current is applied, rapidly alternating charges are set-up on the electrodes
and gives rise to a rapidly alternating electric field between them. The electric field also
influences the material which lies within it.
Effects of Electric Field on Conductors, Insulators and Electrolytes

As we know, conductors are the substances in which electrons can easily be displaced
form their atoms. When such a material lies within a varying electric field, there is rapid
oscillation of electrons and heat is produced.
An insulator is a substance in which the electrons are so firmly held by the central
nuclei that they cannot be easily displaced and results in the distortion of molecules when
varying electric field is applied.
An electrolyte is a substance which contains ions and when a varying electric field is
applied, the ions tends to move from one direction to the other. Electrolytes also contain
diploes which contain two oppositely charged ions, when a varying electric field is applied,
they rotate their direction. These dipoles are electrically neutral, but one end bears positive
and the other a negative charge. As a result of electric field they rotate themselves and come
in an alignment with the electrodes (Fig. 4.3).
Thus, the electric field influences the
material that lies between the plates; this
causes the oscillation of the ions, distortion
of molecules and rotation of dipoles. This
causes production of heat in the tissues by
the electric field of short wave diathermy,
which is the primary function of short
wave diathermy. The heat production is in
accordance with Joules law, i.e. Q = I2RT,
Fig. 4.3: Rotation of dipoles
but depends upon the distribution of the
electric field.
Effects of Electric Field on Dielectric Constants of the Body Tissues

The dielectric constants of the various tissues differ considerably. The tissues of low
impedance such as blood and muscles have higher dielectric constants. The tissues of high
impedance such as fibrous tissues and fat have low dielectric constant.
The relative arrangement of the tissues in the body coming in the pathway of electric
field affects the distribution of the lines of forces and the heat production. If the different
body tissues lie parallel to the electric field, the density of the field and thus the heat
production is greatest in the tissues of low impedance. Thus, when the field is passed
longitudinally through the limb, blood is heated most because of low impedance.
If the different body tissues lie transversely to the electric field, the density of the field and
thus the heat production is greatest in the tissues of high impedance. Thus, when the field
is passed transversely through the limb, fat is heated most because of its high impedance.
Actually, the arrangement of the tissues in the body is such that they do not offer a
true parallel or series (longitudinal or transverse) arrangement, but in fact the mixture
of the two. As the deep tissues generally lie parallel to the field, heating is less in deep
tissues. Also, the heating is more in the tissues of low impedance such as blood. Tissues
in contact with those in which heat is produced, heat are transferred by means of conduc-
tion. For example, when muscles surrounding a deeply placed joint are heated some heat
is transmitted to the joint. Also, when blood is heated in the part being treated, it provides
the heat to other tissues like muscles, etc. and thus the heat is carried away. This helps in
prevention of overheating in the part being treated. Also it helps in heating other tissues
which are not in direct contact with the electric field. Therefore, intensity of electric field or
any other form of heat needs to be gradually increased so as to allow vasodilatation of the
vessels and to avoid overheating.
When short wave diathermy is applied by the capacitor field method the production
of heat is determined by the distribution of electric field, and it tends to be greatest in the
superficial tissues and the tissues of low impedance.
The aim is to achieve an even electric field as far as possible throughout the superficial
and deep tissues so as to obtain even heating in the tissues. To obtain desirable therapeutic
effects the selection and placement of electrodes should be proper. The selection or placement
of electrodes should be based on:
1. Type of electrodes
2. Size of electrodes
3. Spacing of electrodes
4. Positioning of electrodes.
Type of Electrodes
There are various types of electrodes. Electrodes could be pad electrodes, plate electrodes
and disk electrodes. Each electrode consists of a metal plate surrounded by some form of
insulating material.
One type of electrode consists of a thin malleable metal plate covered with a rubber
pad. This has an advantage to get moulded according to the body part. Electrodes of this
type are separated from the skin by perforated felt pad and their position is maintained
by the weight of the body. Undue pressure of the body part should be avoided as this
may crack the plate inside and may hamper the blood supply. The insulating felt pad is
perforated so that it contains a small quantity of air inside, which is preferably the best
spacing material. Thus, it has a disadvantage of not having completely air spacing between
the pad and the body.
Another type of electrode consists of a thick rigid metal plate coated with a thin
layer of insulating material made up of rubber or plastic. The property of an electric
charge is that it concentrates at the edges of a conductor than at anywhere else. Thus,
these plates are frequently convex at the edges which provide a more even electric
field than a flat disk. These plate electrodes are held at a distance from the skin by an
adjusting device, thus provides air as an insulating material which is most preferable
one (Figs 4.4A and B).
The third type of electrode is a disk type electrode. These are having a transparent
plastic cover within which a metal plate is present. These electrodes are commonly circular
Figs 4.4A and B: Electric fields produced by Flat (A) and (B) Convex electrodes
in shape, but special shapes can be used for irregular areas. The position of metal plate
inside the disk can be adjusted. It is advisable to leave small gap between the cover and the
skin to allow for the better circulation of the air.
Size of Electrodes
1. If the two electrodes are of different sizes, they will behave as a capacitor of different
sized plates. The different quantities of electricity are required to charge them to the
same potential. This puts an uneven load to the machine. The charge will concentrate
on the part of larger electrode which lies opposite to the smaller electrode (Fig. 4.5).
Fig. 4.5: Electrodes of different sizes
2. If the electrodes are little larger than the area treated, the outer part where the spread is
greatest is deliberately not utilized. The part of the body to be heated lies in the central
part of the field, which is more even. For treatment of the limbs, the electrodes should
be larger than the diameter of the limbs and for trunk and back electrodes should be as
large as possible (Fig. 4.6).
Fig. 4.6: Correct size of electrodes
3. If the diameter of the electrodes is smaller than that of the limbs, the lines of forces
spread in the tissues, causing more heating of the superficial than of deep structures
(Fig. 4.7).
Fig. 4.7: Smaller electrodes
4. If the diameter of the electrodes is far larger than that of the diameter of the limb, some
of the lines of force bypass it completely and thus results in wastage of energy (Fig. 4.8).
Thus, as a general rule the electrodes should be equal in size and slightly larger than
the area to be treated.
Fig. 4.8: Electrodes too large
Spacing of Electrodes
1. If the distance between the plates is small and the material between them is of high
dielectric constant, the lines of forces spread as they pass between the plates of a
charged condenser (Fig. 4.9).
Fig. 4.9: Distance too small

2. When the distance between the electrodes is large, the spreading out of the electric
field is minimal, while the use of spacing material of a low dielectric constant also
limits the spread of the field (Fig. 4.10).
Fig. 4.10: Adequate distance
3. When the electrode spacing is narrow, the superficial tissue lies in the concentrated
part of the field close to the electrode are thus heated more than the deep tissues,
where density of the field is less (Fig. 4.11).
Fig. 4.11: Electrodes closer to the body
4. If the two electrodes are placed at an unequal distance from the body, the one electrode
is placed nearer to the body than the other then there is a greater heating effect under
the closer electrode than under the farther one. The lines of force under the farther
electrode have a greater distance in which to spread before reaching the body than
those under the nearer one. They therefore cover a greater area of skin and their
density is less than under the nearer electrodes (Fig. 4.12).
Fig. 4.12: Electrodes at uneven distance

If the distance between two electrodes is less than the width of two pads, then the lines
of force will travel through pads only and do not produce heat in the body tissues (Fig. 4.13).
Fig. 4.13: Spacing between two electrodes
Thus, the spacing between the electrodes and the patients body tissues should be as
wide as possible as the machine allows and the material between the electrodes and skin
should be of low dielectric constant, air being the most preferable one.
Positioning of the Electrodes

The positioning of electrodes is different for different structures to be treated. It depends
upon the impedance of the structures and line of electric field. If the structures are of high
impedance (fat and white fibrous tissue) the electrodes should be arranged in such a way
that different tissues lies in series with each other, i.e. at right angles to electric field. If the
structures are of low impedance (blood and muscles), the electrodes should be arranged in
such a way that different tissues lies in parallel with each other and with the electric field.
When treatment is to be given to the ankle joint, the electrodes should be placed on the
medial and lateral sides, so that tissues lie in series with each other and heating the joint
is obtained. If the electrodes are placed longitudinally, tissues lie parallel to the field and
heating of blood vessels and muscles is obtained. In injuries of soft tissues, longitudinal
method may be used, where soft tissues need heating.
Common positioning of electrodes used are:
1. Coplanar positioning of electrodes
2. Contraplanar positioning of electrodes
3. Monopolar method
4. Crossfire technique.
1. Coplanar positioning of electrodes: This method is used over larger area of the body, e.g.
spine and is also called parallel method of placement. It is important that the distance
between the electrodes should be more than the total width of spacing otherwise
electric field will not pass through the tissues at all and will pass directly between the
electrodes (Figs 4.14A and B).
Figs 4.14A and B: Coplanar arrangement of electrodes:

(A) Correct spacing and (B) incorrect spacing
This method is particularly suitable for the superficial structures.

2. Contraplanar positioning of electrodes: This method is used for those structures where
through and through heating is required, e.g. hip, shoulder joint. The electrodes are
placed over the opposite aspects of the limb or joint, i.e. medial and lateral aspect or
anterior or posterior aspect.
This method is particularly suitable for the deeper structures or tissues.
3. Monopolar method: Only one electrode is placed over the treatment area and other
electrode is placed at a distance site or is not used at all. The electrode used produces
a radial electric field (Fig. 4.15).
Fig. 4.15: Monopolar electrode with radial effect
The density of electric field becomes less as the distance from the electrode increases
and thus the heating is superficial.
4. Crossfire technique: In this technique, half of the treatment is given with the placement
of electrodes in one direction, i.e. medial or lateral aspect and another half is used
with the placement of electrodes in other direction, i.e. anterior or posterior aspect.
This method is commonly used for the treatment of the knee joint, sinuses (frontal,
maxillary and ethmoidal) and for pelvic organs (Fig. 4.16).
Fig. 4.16: Crossfire technique for sinus
Cable method or inductothermy

In this method, a thick insulated cable is used for treatment purposes. Electric field or
magnetic field or both are achieved by the use of cable method. When the high frequency
current oscillates in the cable, a varying electrostatic field is set up between its ends and a
varying magnetic field around its center. The cable is coiled around the patients body and
is separated from the patients body by a layer of insulating material.
The electrostatic field: Electrostatic field is produced at the end of the cable and the effects
are similar when the current is applied by a condenser method. The heating is more in
superficial tissues and those of low impedance, also some heating is obtained in deeply
placed structures of high impedance if suitable placing is done.
The magnetic field: The magnetic field varies as the current oscillates and an emf is
produced by electromagnetic induction. If the conductor is a solid piece of conducting
material, the emf gives rise to eddy currents. Such currents are produced specially in the
tissues which lie close to the center of the cable. The eddy currents produce heat and their
effect confines only to the tissues of low impedance, thus heating of fat and white fibrous
tissue is avoided. The currents are produced primarily near the surface of the conductor,
where the magnetic field is strongest and the superficial tissues are heated most. Some heat
is transferred to adjacent tissues by conduction and by the circulation of blood, but the
heating effect is primarily on superficial tissues of low impedance.
Effect of Relative Fields: If the cable is coiled around the material of high impedance the
electric field predominates, while the current produced by the electromagnetic induction
are strongest when the material around which the cable is of low impedance. Thus, when
treating an area of high impedance, particularly if deep heating is required, the electric field
between the ends of the cable is utilized in preference to the magnetic field at its center.
When treating an area of low impedance, particularly if superficial heating is required,
the eddy currents set up by the magnetic field at the center of the cable are utilized in
preference to the electric field. Alternatively, both the effects can be utilized at the same
time; if the whole cable is arranged in relationship to the patients tissues, an electric field
is set up between its ends and eddy currents near its center.
For treatment of the limbs, the cable is coiled around the part. If the area is large, e.g.
the whole of a limb all the cable is used and both electrostatic and electromagnetic fields
are utilized. When treating the smaller area the whole of the cable may not be required;
either the ends or the center may be used, according to the depth of the heating required
and the impedance of the tissues. If the area is of high impedance the electrostatic field
between the ends of the cable is most effective, e.g. for the knee joint, two turns may be
made with each end of the cable, which lies above and below the joint. When treating
two joints both shoulders, a few turns may be made with one end of the cable round one
joint and a similar arrangement of the other end around the other joint. If the area to be
treated is of low impedance, e.g. muscles and blood the eddy currents produce satisfactory
heating so the center of the cable is used.
To treat a flat surface like back, the cable can be arranged in a flat helix, two helices can
also be made from its ends, or a grid arrangement may be used. With the grid the magnetic
field is complex and does not penetrate deeply into the tissues, so heating is mainly by the
electric field, but with the other two methods the tissues are heated with eddy currents.
This flow at right angles to the magnetic lines of forces and the heating produced by a
single helix is therefore in the form of a hollow ring in the tissues lying under the coil.
Advantages of cable method

The cable method is useful:
1. for the treatment of an extensive area which could not be included between the
condenser electrodes.
2. when the area is irregular.

3. when it is desirable to avoid heating of the subcutaneous fat.
Disadvantage of cable method

The impossibility of using air spacing:
Monode electrode: The main benefit of using a monode electrode is that it uses air spacing.
The monode works on the principle of a cable. It consists of a flat helix of a thick wire
mounted on a rigid support, a condenser is lying parallel with the coil making it possible
to use shorter length of wire than that required for the cable. Heating is produced by the
eddy currents.
Dosage
The treatment dosage should have an intensity that causes sufficient warmth (thermal
dosage) of the tissues and the duration of the treatment should be 2030 minutes. The
treatment may be given daily or on an alternate day.
As a general rule, for the treatment of acute inflammation or any recent injury the
intensity of the treatment should be less but it should be carried out more frequently, i.e.
twice daily. The current used may be that which produces mild warmth (midthermal)
and may be reduced to the point at which no warmth is felt (subthermal or athermal). The
duration of treatment is reduced to 510 minutes.
Physiological Effects of Heating the Tissues

The principal effect of short wave diathermy to the body is heating of tissues. This is the
modality which provides deepest heating of the tissues. The main physiological effects
due to heating of the body tissues are:
1. Effects on metabolism of the body
2. Effects due to increased blood supply
3. Effects of heat on the nervous tissues
4. Effects of heat on the muscular tissue
5. Effects of heat on the sweat glands.
Effects on metabolism of the body

As the Vant Hoffs statement states that any chemical change which is capable of
being accelerated is accelerated by the rise in temperature. Therefore, all the chemical
changes of the body that can be accelerated are accelerated by heat. The metabolism of
the body itself is accelerated. Both the anabolism as well as catabolism is enhanced. The
oxygen supply to the tissues is increased, removal of waste products is enhanced, the
nutritional supply to the tissues is increased and thus the healing of damaged tissues is
accelerated.
Effects due to increased Blood Supply

The heat has a direct effect on the blood vessels. It causes vasodilatation of the vessels
in the area of heating. Stimulation of the superficial nerve endings can also cause reflex
dilatation of the arterioles. As a result of vasodilatation there is an increased flow of blood
through the area, so that the necessary oxygen and nutritive materials are supplied and
the waste products are removed. Also, there is increased filtration and diffusion through
different membranes and faster transport of some enzymes. Thus, this results in faster
healing of the damaged tissues and early recovery from the injury.
When there is generalized vasodilatation, the peripheral resistance is reduced. Heat
also reduces viscosity of the blood and thus there is generalized fall in the blood pressure.
Effects of heat on the nervous tissues

Heat alters conduction in the nervous tissues. It produces a sense of sedation. Perception
of pain is also reduced as it enhances the pain threshold.
A high frequency current does not stimulate motor or sensory nerves. The shorter the
impulse of the current, the less is the effect on the nervous tissue. Thus, when a current
of high frequency is used, there is no discomfort in the body and also no contraction of
muscle is produced.
Effects of heat on the muscular Tissue

Increased blood supply provides optimal environment for the muscles to contract. It
provides fresh nutrients, oxygen and removes the waste products faster. Thus, efficacy of
muscles to contract is increased. Rise in temperature also induces muscle relaxation due to
faster removal of the waste products.
Effects of heat on the sweat glands

The heat has an effect on the sweat glands as well. As the heated blood is circulated throughout
the body, it stimulates the centers for the regulation of the sweat. The production of sweat is
increased and thus there is increased elimination of waste products.
Therapeutic Effects of Short Wave Diathermy

Effects on Inflammation
The dilatation of arterioles and capillaries results in an increased flow of blood to the area
which increases supply of oxygen and nutritive material. This increased flow of blood
enhances the supply of more antibodies and white blood cells. The dilatation of capillaries
increases the exudation of fluid into the tissues and this is followed by increased absorption
which along with the increased flow of blood through the area assists in the removal of
waste products. These effects help to bring about the resolution of inflammation. Additional
effects are obtained when the inflammation is associated with bacterial infection which is
discussed in the next point.
In the acute stages of inflammation, treatment should be given with a caution, where
there is already marked vasodilatation and exudation of fluid, as an increase in these
processes may aggravate the symptoms. In the subacute stages, stronger doses may be
applied with considerable benefit. When the inflammation is chronic, a thermal dose of
fairly long duration must be used to have effective.
Short wave diathermy is particularly valuable for lesions of deeply placed structure
such as the hip joint, which cannot easily be affected by other forms of electrotherapy
and radiation. It is of valuable use, in conjunction with other forms of physiotherapy, the
use various inflammatory conditions (e.g. rheumatoid arthritis, capsulitis and tendonitis)
and for the inflammatory changes which frequently occur in the ligaments surrounding
osteoarthritic joints.
Effects in bacterial infections

Inflammation is the normal response of the tissues to the presence of bacteria, the principal
features being vasodilatation, exudation of fluid into the tissues and an increase in the
concentration of white blood cells and antibodies in the area. Heating the tissues augments
these changes and so reinforces the bodys normal mechanism of body dealing with
the infecting organisms; therefore short wave diathermy is of value in the treatment of
bacterial infections like boils, carbuncles and abscesses. Treatment in the early stages may
occasionally bring about resolution of the inflammation without pus formation occurring;
failing this, the development of the inflammatory response is accelerated. Until there is free
drainage, the treatment should be given cautiously, as in all cases of acute inflammation.
When the abscess is draining freely, stronger doses may be applied, the increased blood
supply assisting the healing processes once the infection has been overcome.
In some cases, short wave diathermy appears to aggravate the condition, but increased
discharge for a few days is an indication of acceleration of the changes occurring in be
tissues, and not a contraindication to treatment. However, should be increased discharge
persist it may be an indication that the bodys defence mechanism is already taxed to its
uttermost, so that it is impossible to reinforce its action. This is most liable to occur in cases
of long-standing infection and under these circumstances no benefit is derived from the
application of shortwave diathermy.
Bacteria can be destroyed by heat, but it would be impossible to raise the body tissues
to the necessary temperature without causing damage to the tissues themselves.
Relief of Pain
Mild degree of heating is found to be effective in relieving pain, presumably as a result of
a sedative effect. It has been suggested that pain may be due to the accumulation of waste
products in the tissues due to metabolism and that the increased flow of blood through
the area assists in removing these substances. Strong superficial heating probably relieves
pain by counter-irritation, but it is unlikely that the heating of the skin produced by short
wave diathermy is great enough to have this effect. When pain is due to inflammatory
processes, resolution of the inflammation is accompanied by relief of pain. Short-wave
diathermy assists in bringing about the resolution of inflammation, and so indirectly helps
in relieving the pain. However, strong heating in these cases may cause an increase of pain,
especially in acute inflammation, if the increased blood flow and exudation of fluid cause
an increase of tension in the tissues.
Thus when short wave diathermy is used in the treatment of inflammatory conditions
and in post-traumatic lesions, it brings about relief of pain in addition to its other beneficial
effects. This is particularly valuable when the treatment forms a preliminary to active
exercise, which can then be performed more efficiently.
Effects on muscle tissue

The heating of the tissues induces muscle relaxation, so short-wave diathermy may be
used for the relief of muscle spasm associated with inflammation and trauma, usually as
a preliminary in conduction with the movements. Increased efficiency of muscle action
should also aid the satisfactory performance of active exercises.
Traumatic conditions
The beneficial effects of short wave diathermy on traumatic lesions are similar to those
produced in inflammation. The exudation of fluid (followed by increased absorption)
and the increased flow of blood through the area assist in the removal of waste products,
while the improved blood supply makes available more nutritive materials, so assisting
the healing processes.
Recent injuries should be treated with the same caution as acute inflammation, as
excessive heating is liable to increase the exudation of fluid from the damaged vessels.
Stiff joints and other after-effects of injury require stronger doses, the treatment being a
preliminary to the exercise which is usually the essential part of the treatment.
Reducing healing time

To promote the healing of a wound or injured tissue, an increased blood supply to the
tissues may be of benefit, provided that the vascular responses to heat to the tissues are
normal.
Dangers of Short Wave Diathermy

1. Burns: Short wave diathermy can cause burn, therefore the word burn must be used
to warn the patient of this possible danger. In milder cases tissue is not destroyed but
a bright red patch, i.e. erythema is seen and blistering is liable to occur. In severe cases,
there is coagulation and therefore destruction the tissues, and then burn appears as a
white patch surrounded by a reddened area.
Burns may arise from various causes: Concentration of the electric field, use of
excess current, impaired blood flow, hypersensitivity of the skin, or leads touching the
skin.
a. Concentration of the electric field: Burn is caused due to concentration of the electric
field in the tissues. This causes overheating of the tissues in the affected area. It may
be due to the presence of a small area of material of high dielectric constant within
the field, such as metal or moisture on the tissue, also due to inadequate spacing
over a prominent area of tissue, or to an electrode being badly placed so that one
part of it lies nearer to the tissues than the rest.
In some cases, metal may be embedded in the tissues, e.g. in internal fixation of
fractures, and the danger of causing burns then varies with the position in which
the metal lies. It is the concentration of the electric field, not overheating of the
metal, which is dangerous. If a narrow strip of metal lies parallel to the lines of
force, it provides a pathway of low impedance for a considerable distance and
is liable to cause serious concentration of the field. If, however, it lies across the
field, the easier pathway is provided only for a short distance, and being wide is
much less likely to cause concentration of the lines of force. In these cases, there is
considerable danger of burn, so heating such an area should be avoided.
b. Excess current: The patients sensation is the only indication of the intensity of
the application in short wave diathermy. If excess current is applied due to any
of these causes such as: Patient does not understand the sensations that he should
experience, or cutaneous sensation is defective or if he fall asleep during treatment,
burn could result. Also, if the intensity of the current is increased quickly at the
beginning of the treatment a dangerous level may be reached, and failure to reduce
the current immediately if the heat becomes intense may result in a burn. The
patient should be told that he should feel mild, comfortable warmth such as if
blowing on the dorsum of hand with the mouth and not more than that, otherwise
a burn could result.
c. Impaired blood flow: The blood circulating through the tissues normally dissi-
pates the heat and thus prevents excessive rise of temperature in the area being
treated. If the blood flow is impaired due to any of the causes such as by pressure
on a bony point, tight garments, impaired vascularity or arterial disease, etc. a burn
may occur.
d. Hypersensitive skin: If the skin has become hypersensitive, e.g. by X-ray therapy
or cobalt therapy or due to recent use of liniment, a dose of diathermy which would
normally be safe may cause damage.
e. Leads touching to the skin: If a lead approaches close to the patients tissues and
touches the skin, heat may be produced in the area and it may be sufficient to cause
burn.
If a burn does occurs, in any case it must be reported immediately to the head of
the physiotherapy department. Efforts should be made to minimize the effects of burn.
Medical advice should be taken. As far as possible the burn must be kept clean and
dry, usually being protected with a dry sterile dressing. Legal advice from a lawyer to
protect oneself may also be taken, otherwise patient may take the concerned staff to
the consumer forum.
2. Scalds: A scald is caused by moist heat. It may occur if the area being treated is damp or
moist, e.g. due to perspiration, or if damp towels are used for treatment. If the moisture
is not localized it does not cause concentration of the field. But if it is localized, it may
become overheated and may cause scalding of the skin.
3. Electric shock: An electric shock can occur if contact is made with the apparatus circuit
with the current switched on. It is less possible in modern systems to come in contact
with the apparatus circuit. An electric shock could result from contact with the casing
of the apparatus if casing is not proper or plastic coating is not made on the apparatus.
4. Overdose: Overdose of application of treatment may cause an increase in symptoms,
especially pain and is most liable to occur when there is acute inflammation within a
confined space. It can occur under other circumstances as well and any increase in pain
following treatment is an indication to reduce the intensity of subsequent applications.
5. Precipitation of gangrene: Heat accelerates chemical changes, including metabolic
processes in the tissues, so increasing the demand for oxygen. Normally, this is
supplied by the increased blood flow, but should there be some impedance of the flow
of arterial blood to the tissues the demand of oxygen is not met and gangrene is liable
to develop. Consequently heat should never be applied directly to an area with an
impaired arterial blood supply.
6. Faintness: Faintness is produced by hypoxia of the brain following a fall in blood
pressure. It is particularly liable to occur if, after an extensive treatment, the patient
rises suddenly from the reclining to the erect position from the bed. So, patient should
not be allowed to rise up suddenly from the bed after the treatment. Patient should be
allowed to drink water after treatment.
7. Giddiness: Any electrical current applied to the head may cause giddiness due to its
effects on the contents of the semicircular canals. All diathermic treatments to the head
should be given with the patient fully supported and, if possible, with the head in a
horizontal or an erect position. Also, it is wiser to avoid concentration of diathermy
currents to the eyes because of poor dissipation of heat from the eyes.
8. Dangers to hearing aids or cardiac pacemakers: As the short wave diathermy produces
substantial amount of radiofrequency energy, it may cause interference with the
electrical implants such as hearing aids or cardiac pacemakers. Such patients those
who are using hearing aids or cardiac pacemakers should not be treated with short
wave diathermy and should not be allowed to come in close proximity of the apparatus
for at least two meters.
9. Dangers to other equipments: Low frequency stimulators or interferential therapy
apparatus are also at risk with the short wave diathermy. There are also chances of
interference and damage to these low frequency stimulators or Interferential therapy
apparatus. Therefore, these apparatus must not be kept in the close proximity of the
short wave diathermy and at least a distance of two meters must be maintained.
Contraindications of Short Wave Diathermy

1. Open wound or hemorrhage: Diathermy should never be applied to the open wounds.
It should also be not applied where hemorrhage has recently occurred, because
diathermy causes further dilatation of the blood vessels.
2. Metal in the tissue: Diathermy should also be not applied in cases of metals in the
tissues because diathermy currents may get concentrated in the metals and excessive
heating may cause burn.
3. Disturbed skin sensation: Skin should always be checked for its sensation. Diathermy
may cause burn in cases of disturbed skin sensation.
4. Venous thrombosis or thrombophlebitis: Diathermy is contraindicated in the cases of

venous thrombosis or thrombophlebitis around the area drained by the vessel because
the increased flow of blood may dislodge the clot or aggravates the inflammation.
5. Arterial disease: Diathermy should never be applied to the area having defective
arterial supply. The inability of the circulation to disperse the heat could result in
an increase of temperature in the area, which could lead to burn. Also, if demand of
nutrients cannot be fulfilled with its supply then gangrene can precipitate.
6. Menstruation: Diathermy should never be applied to the abdomen during menstruation
because hemorrhage may further increase.
7. Pregnancy: Diathermy should never be applied to the abdomen or pelvis during
pregnancy.
8. Tumors: Diathermy should not be applied to the area of tumor growth because the
temperature could accelerate the growth of the tumor. Further, due to increased circu-
lation metastasis, i.e. spreading of tumor may occur.
9. Deep X-ray or cobalt therapy: Due to deep X-ray or cobalt therapy the devitalization
of tissues occurs, which could lead to further damage due to the application of short
wave diathermy.
10. Children: Short wave diathermy should also be avoided in children.
11. Mentally retarded patient: It is unsafe to give short wave diathermy to mentally
retarded patients who are unable to understand the degree of heating required and
the necessity to report excessive heating.
12. Unconscious patient: Diathermy should never be given to an unconscious patient.
13. Epileptic patients: Diathermy should also be avoided in epileptic patients.
14. Uncooperative patient: Short wave diathermy should also be avoided in uncooperative
patient.
Pulsed Short wave diathermy

Pulsed short wave diathermy is referred to as pulsed electromagnetic energy or field,
diapulse, etc. which is created by simply interrupting the output of continuous short wave
diathermy at regular intervals. It was invented in 1930s, but became popular only after
1950s. The frequency of pulsed short wave diathermy is same as that of continuous short
wave diathermy, i.e. 27.12 MHz but interpulse interval or off-time is added to it. Pulse
frequency is between 25 and 600 pps, pulse width is between 20 and 40 ms (65 ms is most
commonly used). By adding rest period to the treatment, the average power is considerably
reduced. The heat developed in the tissues is dispersed by the circulation and treatment is
thus referred to as nonthermal treatment. Pulsed short wave diathermy increases the cellular
activity, increases the reabsorption of hematoma, reduces inflammation, reduces swelling
and increases the repair process. The treatment duration varies from 15 to 60 minutes and
indications and contraindications are almost similar to that of short wave diathermy.
Microwave dIathermy
Microwave diathermy can be defined as the use of microwaves for various therapeutic
purposes. Microwave diathermy has a much higher frequency and a shorter wavelength
than short wave diathermy. The frequency and wavelength ranges from 300 MHz to
300 GHz and 1 cm to 1 m. The commonly used frequencies are 2456, 915 and 433.92 MHz
with wavelengths of 12.24 , 32.79 and 69 cm respectively. Therefore, it ranges between
infrared and short wave diathermy. The microwave diathermy can directly penetrate into
the tissues to some extent and can be strongly absorbed by water and high vascular tissues.
Production of Microwave
The microwave diathermy apparatus is connected to main AC which provides it a current
of 50 Hz and a voltage of 220 volts (Fig. 4.17). It is not possible to produce microwaves by
mechanical means and hence a special type of thermionic valve is used which is called a
magnetron. The primary function of a magnetron is to produce high frequency current
Fig. 4.17: Microwave diathermy
required for the production of microwaves. Magnetron is a special type of thermionic

valve characterized by centrally placed cathode and a surrounding circular metal anode.
Coaxial cable carries these high frequency currents from the magnetron and passes it to the
antenna of the emitter. Emitter is also known as director or applicator. Emitter consists of
antenna and reflector. Antenna is mounted in front of a metal reflector. Reflector is a metal
plate which directs the microwaves in only one direction. Emitters are of various size and
shapes. Basically emitters are either circular in shape or rectangular shape. The circular
emitter produces microwaves which are circular in cross-section and denser in periphery
than in the center. Rectangular emitter produces waves which are oval at the cross-section
and denser at the center than at the periphery (Figs 4.18A and B).
Figs 4.18A and B: Different emitters (A) Circular and (B) Rectangular
The distance between the emitter and the skin should be about 1020 cm from the body.
However, this can vary according to the size of the emitter, the part to be treated and the
condition of the patient. If a small area is to be treated, emitter should be closer to the skin
(around 25 cm). If the area to be treated is larger, the distance can be increased to around
1015 cm.
Physiological and Therapeutic Effects

Physiological and therapeutic effects of microwave diathermy are same as that of short
wave diathermy. Microwave diathermy is useful more in local conditions rather than in the
generalized conditions. The amount of heat production is more in muscles as compared to
short wave diathermy since the heat production by the microwaves depends on the watery
content of the tissues. The depth of penetration of microwaves in the tissues is less and is
ranges between 3 mm and 3 cm, while short wave can penetrate as deep as 6 cm. Other
therapeutic effects are the same as of short wave diathermy. It can be used in traumatic and
inflammatory conditions, degenerative arthropathies, enthesopathies, arthritis of joints,
etc. It is useful in the treatment of soft tissues and superficial joints because it is generally
possible to irradiate only one aspect of the body at a time. Microwave diathermy is more
useful in the treatment of superficial tissues those with high fluid content.
Dosage: In acute conditions: 510 minutes and in chronic conditions 1530 minutes,
depending upon the condition of the patient and the type of applicator used.
The patient should feel comfortable warmth as observed while blowing from the mouth
on the dorsum of the hand. Power output can be around 200 watts so as to raise the body
temperature in the therapeutic range of 4045C. Treatment may be given daily or on alter-
nate days.

1. Burns: Microwave diathermy can cause burn on the superficial tissues. Skin must be
kept dry to avoid burns. Water is heated more rapidly by microwaves because of high
degree of absorptive power of these waves. The patients perception of heat is the only
guide of the treatment. The patient must be asked for comfortable warmth. In all cases
of diminished sensations, microwave diathermy should be avoided.
2. Metal in the tissue: Microwave diathermy should not be applied in cases of metals in
the tissues because diathermy currents may get concentrated in the metals.
3. Dangers to hearing aids or cardiac pacemakers: Such patients those who are using
hearing aids or cardiac pacemakers should not be treated with microwave diathermy
and should not be allowed to come in close proximity of the apparatus.
4. Eyes: Treatment on eyes should be avoided. There may be concentration of heat in the
intraocular fluid.
5. Circulatory defects: Patients with hemorrhage, vascular disease, thrombosis or
thrombophlebitis must not receive microwave diathermy.
6. Menstruation: Diathermy should never be applied to the abdomen during menstruation
because hemorrhage may further increase.
7. Pregnancy: Diathermy should never be applied to the abdomen or pelvis during
pregnancy.
8. Tumors: Diathermy should not be applied to the area of tumor growth because the
temperature could accelerate the growth of the tumor. Further, due to increased
circulation metastasis, i.e. spreading of tumor may occur.
9. Deep X-ray or cobalt therapy: Due to deep X-ray or cobalt therapy the devitalization
of tissues occurs, which could lead to further damage due to the application of
microwave diathermy.
10. Patient at particular risk: Treatment should be avoided in children, mentally retarded
patients, uncooperative patient or epileptic patient because these patients cannot
appreciate the amount of heat required for the treatment and thus cannot report for
the overheating.
LONG WAVE DIATHERMY

Long wave diathermy (LWD) is the use of high frequency electromagnetic waves of the
frequency 1MHz and wavelength 300 m.
It has advantage over short wave diathermy in that:
Long wave diathermy has less frequency (1MHz) than short wave diathermy (27.12 MHz),
so there is minimal loss of energy. The power output required for long wave diathermy is
2575 watts only, whereas short wave diathermy generates 2501000 watts of power.
Unlike short wave diathermy, long wave diathermy does not produce any interference
with other equipments. It is said that long wave diathermy can be used even with patients
having metal implants.
Also, the portability and affordability of equipment is good in long wave diathermy as
compared to short wave diathermy.
Treatment of the patients condition

1. Cervical spondylosis
2. Periarthritis shoulder
3. Low back ache
4. Lumbar spondylosis
5. Short Wave Diathermy (SWD) to hip joint
6. Sciatica
7. Osteoarthritis knee
8. Ligament injuries
a. Medial collateral ligament injuries of knee
b. Lateral collateral ligament injuries of knee
c. Lateral ligament of ankle
d. Medial ligament of ankle
9. Plantar fasciitis
10. Salpingitis

Name
Age
Sex
Occupation
Chief complaints
Family history
Treatment history
Investigations
ii. Radiological testsX-rays, MRI scan, etc.
iii. OthersVBI (Vertebrobasilar insufficiency) syndrome: For cervical spondylosis.

Hyperpyrexia
Hypertension
Severe renal and cardiac failure
Epileptic patients
Anemia
Very poor general condition of the patient
Menstruation.
Skin condition
Wound
Tumor
Any metal in the treatment area
Pregnant uterus.
Two test tubes:
One with hot water
One with cold water.
Neon tube
Towels
Pillows
Sand bags.
6. Preparation of the apparatus:
Switching on
Tuning
Regulation of amplitude
Electrodes (Selection of size)
Checking the insulation
Checking the plugs
Checking the socket
Checking the main wire whether it is properly fitted in the main machine.
7. Gaining the confidence of the patient.
8. Positioning the patient:
Comfortable with good support.
9. Preparation of the patient:
Explain (Remove the clothing where the area to be treated)
Testing the skin sensation
Inspection of the part to be treated
Palpation of the part to be treated.
10. Positioning of the electrodes:
Spacing of electrodes
Dos and Donts about the cable. Keep the cables wide apart, do not allow the
patient to touch the cables
Instruction to the patient

Warning to the patient: Not to move, not to sleep.
11. Application to the patient:
Development of appropriate heat level
Duration
Safety.
12. Termination:
Switch off
Removal of the apparatus
Inspection of the part (Erythema)
Palpating the part (Pain).
13. Record about the patient condition:
Dosage given
Space (Narrow, wide)
Duration of the treatment
Name
Address
14. Knowledge of dangers:
If erythema present, apply powder
15. Knowledge of contraindications.
16. Knowledge of effects of spacing.
17. Home instructions.
18. General informations.
Power 230 V AC
Frequency 50 Hz
Disk electrodes Pad electrodes
Narrow 1 inch 2 to 4 folds
Medium 2 inches 4 to 6 folds
Wide 3 inches 6 to 8 folds
CERVICAL SPONDYLOSIS
Cervical spondylosis is the condition in which there are degenerative changes in the
intervertebral joints between the bodies and disk in the cervical spine.
In early stage, it is localized in 23 cervical vertebrae region due to degeneration of
the inter vertebral disk and there is narrowing, osteophytes formation of the anterior
and posterior margins of the spine and these osteophytes causes narrowing of interver-
tebral foramen resulting in nerve root irritation (in later stage). It occurs early in persons
involved in white collar jobs or those susceptible to neck strain because of keeping the
neck constantly in one position while reading or writing.
Incidence
Middle aged and elderly (30 to 45 years of age) women and men.
Particularly, in those occupations which involves a posture of prolonged neck flexion.
Etiology
Poor posture associated with anxiety habit occupation stress (involves) a posture of prolonged
neck flexion. Typists of poorly positioned desks, writer, drivers, holding telephone on one
shoulder, sleeping in awkward conditions.
Pathogenesis
Degeneration of disk results in reduction of disk space and peripheral osteophyte formation.
The posterior intervertebral joints get secondarily involved and generate pain in the neck.
The osteophytes impinging on the nerve roots give rise to radicular pain in the upper limb.
Clinical Features
a. Pain:
Headaches due to upper cervical pathology
Neckache due to middle cervical pathology
Shoulder girdle, shoulder and arm pain due to pathology from C4 to T2 (Radiating
pain)
b. Neck postural muscles are often weak
c. Tenderness in the cervical spine present
d. Limitation of all movements of cervical spine.
Investigations
X-rays : Osteophytes formation (New growth)
Narrowing of joint space
Narrowing of intervertebral foramen.
Treatment: Physiotherapy
Relief of pain:
a. Analgesics, SWD to neck, intermittent cervical traction
b. Shoulder bracing and neck exercise
c. Use of cervical collar (in acute and extremely painful conditions).
Local Contraindications
1. Pulmonary TB
2. Hearing aids
3. VBIFor giddiness
4. Any skin diseases
5. Abscess
6. Recent injury.
Positioning of the Patient

Arm lean sitting (neck and shoulder be in neutral position).
Placement of Electrodes
Monoplanar tech : For localized pain
Coplanar tech : For radiating pain
Spacing : Narrow
Dosage : Acute - Subthermal
Subacute - Mildthermal
Chronic - Thermal
Duration:
Acute - 10 to 15 minutes
Subacute - 15 to 20 minutes
Chronic - 20 to 30 minutes
Home Instructions
i. Isometric neck exercise
ii. Shoulder bracing exercise
iii. Advise not to use pillows
iv. Advise not to flex the head
v. Teach how to read the books
vi. Cervical collar should be used daily
vii. Cervical collar should not worn during sleeping, bathing
viii. Cervical pillow (made of resin, like roll of towel) can be used
ix. Contour pillows can be used
x. Advice not to take cold water bath only hot water bath can be taken
xi. Advise not to carry weight over the head
xii. Advice not to take frequent head bath
xiii. While traveling, advise to sit in middle and on front seats
xiv. While climbing or getting down, ask the patient to keep the neck in neutral position
xv. Advise not to use two wheelers on rough roads.
Effect: Relief of pain.
PERIARTHRITIS SHOULDER
Periarthritis shoulder is a condition characterized by pain and progressive limitation of
some movements in the shoulder joint. In early stages, the pain is worst at night and the
stiffness is limited to abduction and internal rotation of the shoulder. Later, the pain is
present at all times and all the movements of shoulder are severely limited. Often, there is
a history of preceding trauma. The disease is commoner in diabetics.
Incidence: Elderly.
Clinical Features
1. Pain in the shoulder joint may radiate usually to the upper and middle of the upper
arm.
2. Limitation of abduction and external rotation of the shoulder with forced flexion and
extension movements.
3. Tenderness is present in the subacromial region and in the anterior joint line.
When the condition involves the whole rotator cuff it results in total restriction of all
movement of the joint. The condition is then termed as Frozen shoulder (or) adhesive
capsulitis.
Types
1. Primary idiopathic type: Cause is unknown.
2. Secondary type: Occurs in patients with diabetes.
TB, cardiac ischemia and hemiplegia.
Investigations
X-rays are usually normal.
Treatment
1. For painAnalgesics, SWD, Wax bath
2. Mobilization is done to increase external rotation and abduction movements.
3. Local infiltration of hydrocortisone and manipulation under anesthesia can also be
given by orthopedic surgeon.
1. Open wounds
2. Abscess
3. Hemorrhage
4. Vascular impairment
5. Metal inside the area
6. VBIGiddiness result
7. Metal tooth
8. Hearing aids
9. Mastoiditis
10. Hypertension.

Sitting with back support, one pillow between the arm and trunk, and forearm rest over
the thigh or table, i.e. in slight abduction of arm and flexion of forearm.
Placement of the Electrodes

Contraplanar technique (A-P View)
Spacing : Medium
Dosage
: Acute - Subthermal


Chronic - Thermal

Duration :




ome nstructions
H
I
1. Do not lift heavy weight

2. Do not sleep on affected side

3. Pendular exercises or Codmans exercises

4. Ask the patient to do manipulation exercise

5. Do not expose the affected part to cold.

Effects: Relief of pain and increasing joint range of motion.
B CK C
LOW
A
A
HE
Low back ache is characterized by pain which is present in the lower part of the back
experience acute low back ache at some point of time in their life.
tiology
E
In the majority of the patients, the common causes of low back pain are:
1. Idiopathic

2. Discogenic.

Other common are:
1. Congenital: Congenital bony malformations of vertebra, sacralization of lumbar

vertebra, lumbarization of the sacral vertebra, spondylolisthesis, etc.
2. Traumatic: Injudicious sudden lifting, fall with indirect or direct injury to the back,

compression fracture of the vertebral body or transverse process, subluxation or
partial dislocation of lumbar vertebral facet joints, spondylosis and spondylolisthesis.
3. Degenerative diseases: These include annular tears, herniated nucleus pulposus, spinal

stenosis, osteoarthritis, spondylosis and spondylolisthesis.
4. Inflammatory diseases: Rheumatoid arthritis, ankylosing spondylitis, and various types

of sacroilitis.
5. Infectious diseases: Tuberculosis, pyogenic infections of the spine, pelvic or sacroiliac

joint infections.
6. Neoplastic diseases: Benign and malignant tumors involving nerve roots, meninges and

pelvic tumors.
7. Metabolic diseases: Osteoporosis and other metabolic diseases.

8. Circulatory disorders: Vascular insufficiency like varicose veins, abdominal aortic

aneurysm.
9. Toxicity: Chronic radium poisoning may cause aseptic necrosis of bones and pathological

fractures of vertebral bodies.
10. Psychoneurotic problems: Psychoneurotic pain also occurs due to anxiety, tension or

trouble at work.
The disk lesion: If the lesion is due to the disk pathology it is important to identify the
type, extent and the site of the lesion.
The commonly affected disks in the lumbar region are the fourth and fifth disks.
The physical examination: Detailed physical examination is necessary to diagnose the
exact site, extent and cause of lesion. It may consist of the following:
1. Detailed history of the episode

2. Examination of the posture

3. Evaluation of pain characteristics

4. Palpation

5. Range of spinal movements

6. Neurological examination

7. Diagnostic physical tests

8. Evaluation of the functional status.

eurological xamination
N
E
1. L4 and L5: Prolapse of the disk between L4 and L5 will compress the L5 nerve root.

There will be diminished sensation in the dorsum of the foot and anterolateral aspect
of the leg, weakness of the extensor hallucis longusAnkle jerk will be normal.
2. L5 and S1: Prolapse of the L5 and S1 disk compress the S1 nerve root. There will be

diminished sensation over the lateral aspect of the leg and foot, weakness of plantar
flexion of big toe and foot. Ankle jerk will be absent.
nvestigations
I
X-ray of the spine should be done in all cases of LBA.
There are a number of advance techniques of investigations like CT scan, MRI, bone
scan, etc.
reatment
T
Most back pains falls in the nonspecific category of classification and has almost a set
program of treatment. The following things single or in combination are generally
employed in the conservative management of low back pain (Fig. 4.19):


3. Physical agentsmoist heat, SWD, ultrasonic therapy, infrared therapy, etc.

4. Spinal traction

5. Spinal support or brace


Fig. 4.19: Coplanar method
pplication of Short ave Diathermy

A
W
Local contraindications:
1. Peptic ulcer: An ulceration of the mucous membrane of the esophagus, stomach,

duodenum, due to action of the acid gastric juice.
2. Duodenal ulcerPeptic ulcer in the duodenum

3. Pelvic floor infections

4. TB

5. Metal inside the tissues.

Prone lying
One pillow - Under ankle

Other - Under abdomen

Another - Under head

Placement of lectrodes
E
1. Monoplanar techniqueIf there is localized pain pad is kept in L5 region.

2. Coplanar techniqueIf there is radiating pain one over lumbar, another over thigh/

calf-ankle.
Spacing: Medium

Dosage: Acute - Subthermal


Chronic - Thermal

Duration: Acute - 10 to 15 minutes



ome nstructions
H
I
1. Patient is advised to avoid flexion strains

2. Advised to avoid weight lifting

3. Advised to sleep on a firm mattress and not on saggy mattress

4. Advised to do spinal extension exercises

5. Ask to avoid using two wheelers

6. While traveling in bus sit in the middle or front seat

7. Avoid prolonged standing.

B SP D SS
LUM
AR
ON
YLO
I
Acute degenerative disorder of the lumbar spine is characterized clinically by an insidious
onset of pain and stiffness along with radiological finding of osteophyte formation.
Cause
Bad posture and chronic back strain is the most common cause, other cause includes any
previous injury to the spine or an old intervertebral disk prolapse.
Pathology
Primary degeneration begins in the intervertebral joints. This is followed by a reduction in
the disk space and there is formation of osteophytes in the margins. Degenerative changes
develop in the posterior facet joints. The osteophytes around the intervertebral foramen
may encroach upon the nerve root canal and thus interfering with the functioning of the
passing nerve.
Clinical eatures
F
The symptoms begin as low backache, initially worst during activity, but later present
almost all the time. There may be a feeling of a catch while getting up from a sitting
position, which improves as one walks a few steps. The pain may radiate down the limb up
to the calf (sciatica) because of irritation of one of the nerve root. There may be complaint
of transient numbness and paresthesia in the dermatome of a nerve root, commonly on the
lateral side of leg or foot (L5, S1 roots) respectively.
Treatment: The principles of treatment are similar to that described under low back pain.
pplication of S D
A
W
Position of the patient: Prone lying with adequate support posteriorly.
Methods: Monoplanar

Spacing: Narrow



Chronic - Thermal

Short wave iathermy (S D) PJ
d
W
TO
HI
OINT
ndications
I
1. Rheumatoid arthritis: This is a nonsuppurative systemic inflammatory disease of acute

immune response of unknown cause characterized by a symmetrical polyarthritis
affecting peripheral joints and extra articular structure.
2. OA, RA, fracture in neck of femur: Inflammation of the synovial membrane which

becomes edematous and thickened with inflammatory exudates. In later stages,
synovium is vascular and throws fibrous exudates, which gets organized into granu-
lation tissues and spreads over the articular cartilage, the pannus.
The articular cartilage gets loosened from the surface. A similar lytic process occurs on the
deeper surface of the articular cartilage from the granulation. Lesion in the subchondral region
causes the inflammation process to spread into the capsule and into the surrounding tissue.
Clinical eatures
F
There is symmetrical peripheral polyarthritis with early involvement of small joint of the
hands and wrists. The cervical spine, elbows, knee, ankles and metatarsophalangeal joints
are often affected.
reatment
T
1. Rest

2. Splinting

3. Exercise.

During recovery, ice towels or cold packs (Paraffin wax, SWD, hot/cold packs and

hydrotherapy).
ocal Contraindications
L
1. Acute appendicitis

2. Nephritis

3. Menstruation

4. Pregnancy

5. Pelvic floor infections

6. Metal inside the joint

7. Infected wounds.

Position of the patient: Supine lying
Method: Crossfire technique

Ist half: Anterior and posterior

IInd half: Anterior and lateral


Subacute - Mild thermal

Chronic - Thermal

Spacing: Wider

ome nstructions
H
I
1. Advise the patient to walk (not long distance)

2. Advise the patient to take hot water bath

3. Advise the patient to avoid weight lifting

4. Advise the patient to bear the weight

SinusA cavity or channel that permits the escape of pus or fluid.
Narrow: Cervical spondylosis

Ligament injuries

Hip joint, plantar fascitis

Medium: PA shoulder

Sciatica

Wider: OA knee

Salpingitis.

SC C
IATI
A
Sciatica is the condition in which there is a shooting pain along the course of the great
sciatic nerve on the back of the thigh due to a pressure or irritation of the nerve roots of
the sciatic nerve.
1. Herniation of nucleus pulposus into the annulous fibrosis compresses the sciatic nerve

root.
2. Sciatica is manifested commonly in intervertebral disk prolapse. The prolapse is

usually posteriorly.
Common levels are the L4L5 or L5S1 level.

Causes
1. Lumbar disk prolapse (LDP)

2. Osteoarthrosis of lumbar spine

3. Sacroiliac strain

4. Osteoarthrosis or other bone diseases of hip

5. Lordosis and scoliosis of lumbar spine

6. Rectal tumor or chronic constipation

Neuralgia: Due to some compression force on the nerve.

Neuritis: Inflammation of the nerve sheet or connective tissues surrounding the axon.

Clinical eatures
F
Patient is usually a young man complaining of backache and sciatica which come on after
some exertion like lifting a weight.
a. Pain is increased on coughing or sneezing

b. O/E: Sciatic scoliosis is present

c. In acute case, spine is rigid with very acute pain and muscle spasm.

d. Limitation of the movements of the spine with muscle spasm.

SLR (Straight leg raising) is limited on the side with sciatica 25 degree.

Normal45 degree

e. Tenderness at the L-S junction.

f. Burning pain is severe at night

g. Worse on any position that cause pressure on the nerve, e.g. sitting or with stretching,

i.e. the heel on the ground, when in bed patient with hip and knee fixed with ankle
plantar flexed.
Gait: To avoid stretching of the nerve, the patient walks on toes to the foot of the affected
side with plantar flexed ankle. The hip and knee being kept bend, this produces pain while
walking.
1. Advise the patient not to walk or stand for long time

2. Advise to take complete rest.

(If there is radiating pain usually in the region of leg, diagnosis should be proper).

Differential diagnosis: Lumbar spondylosis
Positioning of the patient: Prone lying
Coplanar technique
One pad on the lumbosacral region
One pad on the hamstring region (also in the thigh regionIf the pain is present on the
anterior aspect).
Duration
1015 minutes for all stages.
S S K
O
TEOARTHRITI
OF
NEE
Osteoarthritis is a chronic degenerative disease of joints with exacerbations of acute
inflammation.
Synonyms: Degenerative arthritis, degenerative joint disease, arthritis deformens.
Incidence: Old age people (over the age of 50 years).
Classification
1. Primary: There is no obvious cause; primary osteoarthritis is due to wear and tear

changes occurring in old age due to weight bearing.
2. Secondary: There is a primary disease of the joint which leads to the degeneration of the

joint.
Secondary osteoarthritis arises as a consequence of other conditions, such as

a. Trauma after injury resulting in fracture of the joint surfaces.

b. DislocationRepeated minor trauma, occupational (Tailors)

c. Infection

d. Deformity

e. Obesity

f. Hemophilia

g. Acromegaly

h. Hyperthyroidism.

Clinical eatures
F
1. Pain

2. Swelling

3. Restricted movement

4. Stiffness (Maximum at the end of long rest)

5. Muscle spasm (Usually in Hamstrings)

6. Deformity from prolonged hamstring spasm is flexion and there is deformation of the

tibia with valgus deformity.
7. The joint is enlarged and there is quadriceps atrophy especially vastus medialis.

8. Inability to squat in Indian toilet.

On Examination
The following findings may be present:
1. Tenderness of the joint line

2. Crepitus on moving the joint

3. Irregular and enlarged-looking joint due to formation of osteophytes

4. Deformityvarus of the knee, flex-add-external rotation of the hip

5. Effusionrare and transient

6. Terminal limitation of joint movement

7. Subluxation detected on ligament testing

8. Wasting of quadriceps femoris muscle.

nvestigations
I
Radiological Examination
The diagnosis of osteoarthritis is mainly radiological. X-rays are usually done to find
changes in the joint.
The following are some of the radiological features:
1. Narrowing of joint space, often limited to a part of the joint, e.g. may be limited to

medial compartment of tibiofemoral component of the knee.
2. Subchondral sclerosis: Dense bone under the articular surface

3. Subchondral cysts

4. Osteophyte formation

5. Loose bodies

6. Deformity of the joint.

S C D S S
E
ON
ARY
O
TEOARTHRITI
Alteration in the congruency of the articular surfaces of tibia, femur and patella.
Treatment

2. Static quadriceps exercises

3. Short wave diathermy

4. Intra articular hydrocortisone (if required).

Local ontraindications
C
1. Hemorrhage

2. Abscess

3. Ulcer

4. Thrombosis

5. Vascular impairment

6. Metal around the area

7. Loss sensation

8. Recent injury

9. Fracture

10. Recent scars

11. Varicose veins

12. Hemophilic arthritis.

ositioning of the atient
P
P
Long sitting with back support and the affected leg is rest on a stool with a pillow.
lacement of Electrodes
P
Contraplanar technique (Medial and lateral view)
Crossfire technique (Med Lat side; Sup Inf side).
Duration: Acute - Ist day to 10th day

Subacute - 2nd weeks to 6th month

Chronic - More than 6th month

Duration of Treatment



Dosage
Acute - Mild thermal

Subacute - Subthermal

Chronic - Thermal

ome nstructions
H
I
1. Advise hot bath formentation

2. Teach static quadriceps exercises

3. Avoid prolonged standing

4. Avoid weight lifting.

J S
LIGAMENT
IN
URIE
Ligaments are comprised of white connective tissue which form bands either inside or
outside capsule of a synovial joint. They are tough, inelastic but flexible. So that they limit
and control normal movement.
edial Collateral igament njuries of Knee

M
L
I
Medial collateral ligament is more commonly injured than the lateral.
Anatomy
Attachments are the medial femoral condyle and the medial tibial condyle. The deep fibers
are attached to the medial meniscus. It stabilizes the knee against valgus strain.
Etiology
Cause is usually an abduction force where the foot and tibia are fixed, and the femur is
forced medially.
A rotation force of the femur on the fixed tibia will also injure the ligament.
A combination of these two forces produces a severe injury.
It is common in sports activities such as football, high jumping and skiing. Some times
happens in swimming during an excessively forceful kick in breast stroke.
Sprain of igament
L
linical Features
C
1. Pain over medial side of the knee.

2. Tenderness over the upper and lower attachment of the ligament.

3. Pain is increased on applying abduction stress at the knee.

4. No abnormal motility.

5. Swelling in severe stage.

Position: Patient is positioned with a leg on the table in high sitting with pillow under
thigh and leg and a pad under Tendo Achilles (Fig. 4.20).
Treatment
1. Rest (by applying posterior toe splint)

2. Compression bandage for a week.

Fig. 4.20: Contraplanar method
Partial upture of the igament

R
L
linical Features
C
1. Hemarthrosis.

2. On applying abduction force at the knee, there will be severe pain and abnormal

mobility.
3. Tenderness at the attachment.

Treatment
1. The knee is aspirated under aseptic precautions

2. Compression bandage

3. Posterior plaster slab for 3 weeks

4. Quadriceps exercises.

Complete upture of the igament
R
L
This is caused by a very severe valgus strain at the knee. This may be associated with
fracture of the femoral condyle of the tibia.
There is abnormal mobility, where the knee is flexed to 10 degree.
linical Features
C
In addition to marked swelling of the knee due to hemarthrosis, there will be abnormal
abduction mobility at knee when knee is held at 10 degree flexion.
nvestigation
I
X-ray: Anteroposterior view shows widening of the medial joint space.
Treatment
1. Early repair should be done.
2. Reconstruction of the ligament is sometimes necessary.
Lateral Collateral Ligament Injuries of Knee

Anatomy
Attachments are the lateral femoral condyle and the head of the fibula. It has no connection
to the lateral meniscus. It stabilizes the knee against varus strain.
Lateral ligament injury is less common than the injury to medial ligament injury.
Etiology
It is caused by a varus stress. It may happen when there is a sideway fall for, e.g. off a
motor cycle or bicycle. Severe twisting may tear this ligament.
The same types of injuries, sprain, partial rupture and complete rupture of the ligament
occur due to hit on knee aspect of the weight.
Treatment is also based on the same principles as above.
1. Hemorrhage
2. Abscess
3. Thrombosis
4. Injuries
5. Ulcers
6. Metal around the area
7. Loss of sensation
8. Hemophilic arthritis
9. Varicose vein
10. Recent fracture
11. Recent scars.

Long sitting with back support.
Placement of the Electrodes

Contraplanar technique (Medial and Lateral Aspect).
Spacing: Uneven spacing
a. For medial ligament injury:
Medial aspect - Narrow
Lateral aspect - Wider
b. For lateral ligament injury:
Medial aspect - Wider
Lateral aspect - Narrow
Dosage: Acute - Mildthermal

Subacute - Subthermal
Chronic - Thermal
Duration: Acute - 10 to 15 minutes
Home Instructions
1. Avoid prolonged standing.
2. Avoid prolonged walking.
Lateral Ligament Injuries of Ankle

The ligaments of the ankle are injured when the plantar flexed foot is forced suddenly into
inversion (lateral ligament) or eversion (medial ligament) injury of the lateral ligaments is
the most common.
Anatomy
Lateral ligament of the ankle consists of three segmentsAnterior talofibular, posterior
talofibular and the middle calcaneofibular.
Etiology
Acute: This injury is common in sports activities such as cross country running and hiking.
It is also quite common in general terms when a person slips off a pavement or walks on
uneven surfaces.
Chronic: Poor reflex coordination of peroneal to prevent twisting during walking over
uneven ground.
Poor support from footwear, torn heels or old shoes which have become too large.
Prolonged sitting with feet turned in (causes lengthening).
Clinical Features
1. Pain
2. Swelling in the lateral aspect of the ankle
3. Loss of function.
Investigations
X-rays: Widening of lateral half of the joint spaces.
Treatment
First aid: Ice, compression bandage, elevation of the part, strapping (everted).
Complications
Chronic pain, instability at the ankle.
Medial Ligament Injuries of Ankle

Less common, sudden eversion violence causes injury to medial ligament.
Tenderness is at the upper attachment of the medial ligament to the medial malleolus.
Spacing: Uneven spacing for medial ligament injury,
Medial aspect Narrow
Lateral aspect Wider
For lateral ligament injury,
Medial aspect Wider
Lateral aspect Narrow
Treatment
Strapping (Inverted position).
PLANTAR FASCiITIS
Plantar fasciitis is an aseptic inflammation of the plantar fascia occurs in persons who do
a great deal of standing and walking. It causes severe pain and tenderness over the sole of
foot.
Incidence
Middle-aged adults on injury or a pulling on plantar aponeurosis. Repeating attack during
physical training produces ossification in the postattachment of the plantar aponeurosis
forming a calcaneal spur.
Clinical Features
a. Pain is present in one or both heels.
b. Pain is worse in early morning and patient is unable to bear weight on the foot while
getting up from bed.
c. Tenderness on pressure over the medial tuberosity of calcaneum.
Procedures
1. Receiving the patient
2. Case sheet reading
3. Preparation of trays
4. Preparation of apparatus
5. Position of the patient
6. Preparation of the patient
7. Position of the electrodes

8. Application of the modality.
Investigations
X-rays: In the lateral view, heel show calcaneal spur (spur occurs as a reaction to the local
inflammation of the plantar fascia and ligaments with deposition of calcium at the side of
ligamentous attachments).
The severity of the pain is not proportionate to the size of the spur.
Treatment
Hot water formentation.
SWD, Footwear with MCR
a. Pain is relieved by addition of soft foam pad in the heel of the footwear
b. Ultrasound therapy
c. Hydrocortisone injection
d. Surgical removal of spur.
Plantar fasciitis is the formation of bony spur due to continuous pull of plantar aponeu-
rosis leads to periosteal ossification.
Position of the Patient

Long sitting with back support, heels supported over a stool with a pillow.
1. Hemophilia
2. Recent injury
3. Open wounds over foot
4. Ulcer
5. Cracks over heels
6. Recent fracture of foot
7. Trophic ulcers (Plantar ulcer)
8. Fissures
9. Gangrene
10. Thorn prick.
Dosage
Thermal dose for all three stages (blow of air can be felt).
Duration
Acute : 10 to 15 minutes
Subacute : 15 to 25 minutes
Chronic : 20 to 30 minutes
Spacing: Narrow
Size of the electrodes: 2 inches
Placement of the electrodes: Monoplanar (close of the heel).
Home Instructions
Hot water formentation:
1. Ask the patient to avoid prolonged standing
2. Ask the patient to wear microcellular rubber (MCR)
3. Ask the patient not to walk for prolonged duration
4. Ask the patient not to walk on the improper road without MCR
5. Ask the patient to avoid high heel shoes
6. Ask the patient to bear the weight.
Effects: Effect on inflammation, relief of pain.
SALPINGITIS (PELVIC INFLAMMATORY DISEASE)

It is the infection of the female reproductive organs (infection acute or chronic in the fallo-
pian tubes).
Salpingitis may be caused by any of pyogenic organisms that is streptococcus. Staphy-
lococcus, gonococcisuppurative salpingitis.
Tuberculous salpingitis(Extrapulmonary tuberculosis).
Physiologic salpingitisPelvic inflammatory changes at the time of menstrual cycle
cause pelvic pain (edema in tubes).
If salpingitis is not treated, it may lead to sterility.
1. Pelvic floor infectionGonorrhea
2. Epilepsy
3. Hyperpyrexia
4. Hypersensitive skin
5. Intrauterine devices like copper-T
6. Pelvic tumors
7. Pregnancy
8. Infection
9. Hemorrhage
10. Any abscess
11. Open wounds
12. Deep Xray therapy
13. Cobalt therapy.

Half lying One pillow under head and back
Other pillow under leg.
Crossfire technique
Ist half: Lower abdomen L3L5 region
IInd half: L3L5 region Gluteal sides region
Spacing: Wider
Dosage: Thermal dose for all three stages
Duration: 10 to 15 minutes for all stages.
Home Instructions
Advice the patient to look for any erythema formation or burns. If there are burns apply
powder until erythema subsides.
5 Radiation Therapy
Radiation therapy may be defined as treatment by means of radiations. The term Actino-
therapy is also used for this.
Radiation therapy may include:
1. Infrared radiations
2. Ultraviolet radiations.
Infrared radiations
The infrared rays are electromagnetic waves with the wavelengths of 750 to 400000 nm and
frequency 4 1014 Hz and 7.5 1011 Hz. It lies beyond the red boundary of visible spectrum.
Any hot body can produce infrared rays like the sun, electric bulb, coal fire, gas fire, etc.
Sun is the natural source of infrared radiations. Infrared radiations can be produced by
artificial generators. In the Physiotherapy departments infrared rays are produced by two
types of generators:
1. Nonluminous generators
2. Luminous generators.
Nonluminous generators provide infrared rays only whereas luminous generators
emit infrared rays, visible as well as ultraviolet rays. Therefore, nonluminous generators
are termed as infrared radiation generators because they emit only infrared rays. The heat
produced by luminous generator is called the radiant heat.
Nonluminous Generators
Nonluminous generator consists of a simple type of element or coil wound on a cylinder of
some insulating material such as fireclay or porcelain. An electric current is passed through
the wire which results in the production of heat. This heat produces infrared rays which
are transmitted through the porcelain. Porcelain gets heated by the method of conduction
but the radiations generated in this way also include some of the visible rays. Therefore to
avoid this, the coil is embedded in fireclay or porcelain or placed behind fireclay. Now the
emission of rays is entirely from the fireclay which is commonly painted black and thus very
few visible rays are produced. The element or the coil is thus placed at the focal point of a
parabolic or spherical reflector. The reflector is mounted on a stand and its position can be
adjusted as required (Fig. 5.1).
Radiation Therapy 197
Fig. 5.1: Nonluminous infrared lamp with counter-balanced height

adjustment and a wire mesh guard
In another type of nonluminous generator, a steel tube within which an electric coil is
embedded on some material which is electric insulator but good conductor of heat is used.
Electric current is passed through the central coil and thus heat is produced. The steel tube
thus emits infrared rays.
The construction of the outer part of the apparatus should be such that the reflectors
and other parts do not become excessive hot and there should be wire mesh surrounding
the element.
All of these nonluminous generators take some time to get heated up for the production
of infrared radiations, so they should be switched on before 57 minutes of the treatment.
Luminous Generators
Luminous generators emit infrared, visible and a few ultraviolet rays. These generators
are in the form of incandescent lamps or bulbs. An incandescent lamp consists of a wire
filament enclosed in a glass bulb, which may contain an inert gas at low pressure. The
filament is a coil of fine wire which is usually made up of tungsten. Tungsten is a metal
which is used because it can tolerate repeated heating and cooling. The exclusion of air
prevents oxidation of the filament, which would cause an opaque deposit to form on the
inside of the bulb. Incandescent bulb is usually mounted at the center of the parabolic
reflector and the reflector is mounted on an adjustable stand. These luminous generators
emit the electromagnetic waves with the wavelength in between 350 and 4000 nm, the
maximum proportion of the rays having wavelength in the region of 1000 nm. The front
of the bulb is usually red so as to filter out the shorter visible and the ultraviolet rays.
Depth of Penetration of Rays

Luminous generator produces infrared rays having wavelength between 350 and
4000 nm. It can penetrate into dermis and epidermis of the subcutaneous tissue.
Nonluminous generator produces infrared rays of wavelength 750 to 15000 nm which
can penetrate the superficial dermis only. The depth of the penetration depends upon
the wavelength and the nature of the material (Fig. 5.2). Thus, infrared rays produced
from a luminous generator have more penetration power than that produced from
nonluminous generator.
Fig. 5.2: Cross-section of the skin, showing the extent of penetration of

radiations of different frequencies
Techniques of the Treatment

The choice of apparatus
In most cases luminous and nonluminous generators are equally suitable, but in some
instances one proves more satisfactory than the other. When there is acute inflammation
or recent injury, the sedative effect of rays obtained from nonluminous generator may
prove more effective for relieving pain than the counter-irritant effect of those from
the luminous source. For lesions of a more chronic type, the counter-irritant effect of
the shorter rays may prove to be of value, and under these circumstances a luminous
generator is chosen.
Selection of the generator according to the area to be treated is done. If only one surface
is to be treated, a lamp of a single element mounted on a reflector is used. If several aspects
are required to be irradiated, a tunnel bath is more effective. The temperature reached in a
tunnel bath is higher than produced by other lamps and this may be advantage if chronic
lesions are to be treated.
Before application the lamp must be checked to ensure that it is working correctly.
Nonluminous generators must be switched on an adequate time before application.
Preparation of the Patient

The clothes must be removed from the area to be treated and skin is checked for its sensa-
tion against heat and cold. It is unwise to give treatment if the skin sensation is found
defective. The patient should be comfortable and fully supported so that he does not move
unduly during treatment. The patient is warned that he should experience comfortable
warmth and he should report immediately if the heating become excessive as undue heat
may cause burn. He should be instructed not to touch the apparatus and nor to move
nearer to the apparatus.
Arrangement of the lamp and patient: The lamp is positioned so that it is opposite to the
center of the area to be treated and the rays strike the skin at the right angle thus ensuring
maximum absorption. The distance of the lamp from the patient should be measured.
Optimum distance is around 5075 cm depending upon the output of the generator.
Care must be taken that the patients face is not exposed to infrared rays, eyes must be
shielded to avoid this.
Laws Governing the Effects of Electromagnetic Radiations

When electromagnetic radiations strike or come in contact with other objects they may
be reflected, refracted or absorbed. As a general rule, those radiations that have a longest
wavelengths tend to have greatest depth of penetration, regardless of the frequency. It
should also be noted that a number of other factors can also contribute to the depth of
penetration.
Various laws regulating the depth of penetration are:
1. Arndt-Schultz principle: It states that no reaction or changes can occur in the body
tissues if the amount of energy absorbed is insufficient to stimulate the absorbing
tissues. Addition of threshold energy and above quantity of energy will stimulate the
absorbing tissue to normal function and if too great a quantity of energy is absorbed
then added energy will prevent normal function or will destroy tissue.
2. Law of Grothus-Drapper: It states that the rays must be absorbed to produce the effect
and the effects will be produced at that point at which the rays are absorbed.
3. Cosine law: It is also known as Lambert-Cosine law. Cosine law explains the effect
of angle at which the rays strike. It states that the proportion of rays absorbed varies
as per the cosine of the angle between the incident and the normal. Thus, the larger
angle at which the rays strike at the body surface, lesser will be the absorption and
vice versa. If the rays strike at 90 to the body part, then angle between the incident
and normal are perpendicular will be zero and the cosine of 0 is maximum, i.e. 1.
Thus, there will be maximum absorption if the rays that will strike the body part at
90 as per this law.
4. Law of inverse square: Law of inverse square explains the effect of distance on the
intensity of infrared rays. It states that the intensity of a beam of rays from a point
source is inversely proportional to the square of the distance from the source.
Application of infrared treatment

At the start of the treatment exposure the intensity of the radiation should be low, but after
510 minutes when vasodilatation has taken place and the increased blood flow has become
established, the strength of the radiation may be increased. This can be achieved by moving
the lamp closer to the patient or by adjusting the variable resistance.
The physiotherapist should be near the patient throughout the treatment session and
should reduce the intensity of radiation if the heat becomes excessive. If the irradiation
is extensive, it is desirable that sweating should occur to counteract any excess rise in
body temperature. Sweating is encouraged if the patient is provided water to drink during
treatment.
At the end of the treatment the skin should be mild red, not excessively red. After
extensive irradiation the patient should not rise suddenly from the recumbent position or
go out into the cold immediately.
Duration and frequency of treatment: In cases of acute inflammation or recent injuries and
for the treatment of wounds, an exposure of 1015 minutes is adequate, but it may be
applied several times during the day. In cases of chronic conditions longer exposures may
be used.
Physiological effects
Infrared treatment produces heating effect in the superficial epidermis and dermis, thus
resulting in vasodilatation which increases blood circulation in that area. This will lead to
more oxygen supply and nutrient supply in that area leading to draining of waste products
resulting in the relief of pain. The sedative effects on nerve endings lead to reduction in
the muscle spasm.
Therapeutic Effects
1. In relieving pain: Infrared radiations are effective in relieving pain. Mild heating on
the superficial tissues by infrared radiations causes sedative effects on the superficial
sensory nerve endings. Pain may be due to accumulation of waste products of
metabolism, an increased flow of blood through the part removes these substances
and thus relieves the pain.
The pain due to acute inflammation or recent injury is relieved most effectively by
mild heating. When pain is due to chronic injury or inflammation, stronger heating is
required. The treatment may last up to 30 minutes.
2. In muscle relaxation: Relaxation of muscles is achieved by heating the tissues. Mild
heating by infrared causes relaxation of muscles and thus relieves spasm. Relief of
pain also induces relaxation in muscles and helps relieving muscle spasm associated
with injury or inflammation. Relaxation of muscles provides greater range of motion
to the exercising part as it relieves muscular spasm.
3. In increasing blood supply: Infrared radiations increase the temperature in the
superficial tissues, causing vasodilatation in the superficial tissues. It provides more
white blood cells and fresh nutrients to the area being treated. It also accelerates
removal of waste products and helps bring about resolution of inflammation. It is
most beneficial in the treatment of various arthritic conditions of joints which leads to
inflammation and stiffness. Cases of postimmobilization stiffness, open wound and
infections can also be effectively treated. Fresh supply of blood rejuvenates the tissues,
removes waste products of metabolism and also relieves muscular spasm.
Dangers of Infrared Radiations

1. Burn: Excessive heating of superficial tissues causes burn. Sensation must be checked
before starting the treatment. If sensation is not proper, the patient may not appreciate
the extent of heating. The burn may be caused due to the following reasons:
i. If intensity of radiation is too high
ii. If sensation is not proper
iii. Patient fails to report over heating
iv. Unconscious patient
v. Patient moves closer to the lamp
vi. Falls asleep during the treatment.
The patient must be warned to inform undue heating immediately. The spacing
must be reduced gradually in order to increase the heating. Impaired blood flow
through the part, which may be due to some circulatory defect or due tight garments
reduces circulation and thus causes burn.
2. Electric shock: Electric shock can occur if some exposed part of the circuit is touched
by the patient. Due to heating of the wires in the circuit, insulation of wires may go off
and thus regular checking of wires is necessary to avoid electric shock.
3. Faintness or giddiness: Extensive irradiation may cause fall in blood pressure which
may result in faintness or giddiness due to hypoxia of the brain. This is particularly
common when the patient rises up suddenly from the recumbent position after
extensive treatment.
4. Headache: Irradiation of the back of the head may cause headache. Headache may
also occur when treatment is given during hot weather. Lots of fluid goes off the body
in the form of sweating during treatment. Plenty of water needs to be replenished
during or after the treatment especially in hot weather.
5. Gangrene: Gangrene may be caused in the areas of defective arterial blood supply
following prolonged irradiation by infrared radiation. Arterial supply to the area
being treated needs to be proper to avoid gangrene.
6. Injury to the eyes: Direct heating over the eyes causes drying up and thus leads to
corneal or retinal burns. Eyes needs to be protected following treatment to avoid
injury.
Contraindications
Infrared radiations should not be applied to the areas of:
1. Defective arterial blood supply
2. Areas where there is danger of hemorrhage
3. Defective skin sensation
4. Directly over the eyes
5. After deep x-ray or cobalt therapy
6. Known cases of tumors.

1. Low back ache
2. Postimmobilization stiffness
3. Edema.
INFRARED RADIATIONS

Name
Age
Sex
Occupation

Chief complaints
Family history
Treatment history
Investigations:
1. Hematological tests:
UrineAlbumin, sugar, etc.
2. Radiological testsX-rays, etc.
Any allergic reaction (e.g. Hypersensitivity to sunlight)
3. General contraindications:
Hyperpyrexia
Hyperesthesia
Dermatitis
Tuberculosis
Inflammation and injury
Deep X-ray therapy or cobalt therapy
Photosensitivity
Epilepsy
Renal or cardiac problems
Vascular impairment
Mental retardation
Use of sensitizers like insulin, etc.
4. Local contraindications:
Skin conditions
Ulcers
Tumor
Neoplastic tissue.
Two test tubes
One with hot water
6. Preparation of apparatus: The infrared lamp is conveniently positioned. Points to keep
in mind are:
Selection of lamp
Switching on
Regulation of power
Checking the plugs
Checking the socket
Checking the main wire whether it is properly fitted in the main machine
8. Positioning the patient.
9. Treatment:
Placing the lamp
Instructions to the patient
i. Not to move
ii. Not to touch the machine
iii. Not to sleep
10. Application: Maintain the lamp so that rays are at right angles in order to achieve
maximal penetration. Record the distance between the lamp and the treatment area.
11. Termination: Record the time duration for which lamp was applied. Switch off the lamp.
Check the skin condition. Immediate increase or decrease of pain needs to be recorded.
12. Other points:
Knowledge of condition
Record of treatment.
LOW BACK ACHE

Low back ache is characterized by pain which is present in the lower part of the back
experience acute low backache at some point of time in their life.
Etiology
In the majority of the patients the common causes of low back pain are:
1. Idiopathic
2. Discogenic.
Other common causes are:
1. Congenital: Congenital bony malformations of vertebra, sacralization of lumbar
vertebra, lumbarization of the sacral vertebra, spondylolisthesis, etc.
2. Traumatic: Injudicious sudden lifting, fall with indirect or direct injury to the back,
compression fracture of the vertebral body or transverse process, subluxation or
partial dislocation of lumbar vertebral facet joints, spondylosis and spondylolisthesis.
3. Degenerative diseases: These include annular tears, herniated nucleus pulposus, spinal
stenosis, osteoarthritis, spondylosis and spondylolisthesis.
4. Inflammatory diseases: Rheumatoid arthritis, ankylosing spondylitis, and various types
of sacroiliitis.
5. Infectious diseases: Tuberculosis, pyogenic infections of the spine, pelvic or sacroiliac
joint infections.
6. Neoplastic diseases: Benign and malignant tumors involving nerve roots, meninges and
pelvic tumors.
7. Metabolic diseases: Osteoporosis and other metabolic diseases.
8. Circulatory disorders: Vascular insufficiency like varicose veins, abdominal aortic
aneurysm.
9. Toxicity: Chronic radium poisoning may cause aseptic necrosis of bones and patho-
logical fractures of vertebral bodies.
10. Psychoneurotic problems: Psychoneurotic pain also occurs due to anxiety, tension or
trouble at work.
The disk lesion: If the lesion is due to the disk pathology it is important to identify the
type, extent and the site of the lesion.
The commonly affected disks in the lumbar region are the fourth and fifth disks.
The physical examination: Detailed physical examination is necessary to diagnose the
exact site, extent and cause of lesion. It may consist of the following:
1. Detailed history of the episode
2. Examination of the posture
3. Evaluation of pain characteristics
4. Palpation
5. Range of spinal movements
6. Neurological examination
7. Diagnostic physical tests
8. Evaluation of the functional status.
Neurological Examination
1. L4 and L5: Prolapse of the disk between L4 and L5 will compress the L5 nerve root.
There will be diminished sensation in the dorsum of the foot and anterolateral aspect
of the leg, weakness of the extensor hallucis longus. Ankle jerk will be normal.
2. L5 and S1: Prolapse of the L5 and S1 disk compress the S1 nerve root. There will be
diminished sensation over the lateral aspect of the leg and foot, weakness of plantar
flexion of big toe and foot. Ankle jerk will be absent.
Investigations
X-ray of the spine should be done in all cases of LBA.
There are a number of advance techniques of investigations like CT scan, MRI, bone
scan, etc.
Treatment
Most back pains falls in the nonspecific category of classification and has almost a set
program of treatment. The following things single or in combination are generally
employed in the conservative management of low back pain:
3. Physical agentsMoist heat, SWD, ultrasonic therapy, infrared therapy, etc.
4. Spinal traction
5. Spinal support or brace
Applications of Infrared Therapy

General contraindications:
1. Hyperpyrexia
2. Tuberculosis
3. Inflammation
4. Deep X-ray therapy or cobalt therapy
5. Photosensitivity
6. Epilepsy
7. Renal or cardiac problems.
1. Skin conditions: allergy, ulcer, etc.
2. Tumor, etc.
3. Abnormal skin sensation.
Checking skin sensation
Two test tubes
One with hot water

Sitting position: With back unsupported and exposed toward the lamp.
Side lying position: comfortable with support of pillows and back exposed toward the lamp.
Placement of Infrared Lamp

Place the lamp at about 12 feet away from the treatment area so that rays are at right
angles in order to achieve maximal penetration. Record the distance between the lamp and
the treatment area.
Duration: Acute condition 10 to 15 minutes
Subacute condition 15 to 20 minutes
Chronic condition 20 to 30 minutes.
Home Instructions
1. Patient is advised to avoid flexion strains
2. Advise to avoid weightlifting
3. Advise to sleep on a firm mattress and not on saggy mattress
4. Advise to do spinal extension exercises
5. Ask to avoid two wheelers
6. While traveling in bus sit in the middle or fron seat
7. Avoid prolong standing.
POSTIMMOBILIZATION STIFFNESS
Postimmobilization stiffness could occur due to immobilization under plaster cast or due
to some arthritic conditions like rheumatoid arthritis, gouty arthritis or infective arthritis,
etc.
Aim of treatment with infrared lamp is to increase vascularity and to reduce pain.
2. History taking
Family history
Treatment history
Investigations:
i. Hematological tests: Hb, TLC, DLC, ESR, etc.
RA Factor
ii. Radiological testsX-rays, etc.
Hyperpyrexia
Dermatitis
Tuberculosis
Inflammation
Photosensitivity
Epilepsy, etc.
Skin conditions: Hyperesthesia, etc.
Ulcers, tumors, etc.
Neoplastic tissue.
Two test tubes:
One with hot water
6. Preparation of apparatus: The infrared lamp is conveniently positioned at about 12
feet away from the treatment area.
7. Positioning the patient: Comfortable with good support and exposing the part to be
treated toward the lamp.
8. Application: Maintain the lamp so that rays are at right angles in order to achieve
maximal penetration. Duration: 10 to 15 minutes and later duration can be gradually
increased upto 20 to 30 minutes.
9. Check for excessive redness: Immediate increase or decrease of pain needs to be
recorded. Check for any headache, faintness or giddiness. Advise the patient not to
rise suddenly from the recumbent position.
Absorption of exudates or edema

The accumulation of exudates in skin and subcutaneous tissues is known as edema. It
could be due to heart failure, chronic venous inefficiency or due to nephrotic syndrome.
In heart failure excessive retention of salt and water leads to edema dormation. In old age
there could be inferior vena cava obstruction or iliofemoral vein thrombosis leading to
chronic venous inefficiency and thus edema formation. In nephrotic syndrome there is
more generalized form of edema which often affects face and arms.
Aim of treatment with infrared lamp is to increase vascularity and to reduce exudates.
Treatment history
Investigations
ii. UrineAlbumin, sugar, etc.
Hyperpyrexia
Hyperesthesia
Dermatitis
Tuberculosis
Photosensitivity
epilepsy
Mental retardation.
Skin conditions
Ulcers
Tumor
Neoplastic tissue.
Two test tubes
One with hot water
6. Positioning of the patient: Comfortable with good support.
vicinity of the patient and at appropriate reachable distance from the lamp.
8. Placing of infrared lamp: The infrared lamp is conveniently placed at about 12 feet
away from the treatment area. Maintain the lamp so that rays are at right angles in
order to achieve maximal penetration. Duration: 10 to 15 minutes and later duration
can be gradually increased upto 20 to 30 minutes.
9. Check for any redness or excessive rise in skin temperature. If there is excessive rise in
skin temperature which could lead to burn, treatment can be discontinued. Check for
any headache, faintness or giddiness. Advise the patient not to rise suddenly from the
recumbent position.
The Ultraviolet radiations
Ultraviolet radiations are the electromagnetic energy which falls between visible rays and
X-rays and have wavelength between 10 nm and 400 nm. Ultraviolet radiations are invisible
to the human eye. Ultraviolet radiations can cause sunburn and tanning on exposure to the
sunlight. Ultraviolet radiations transmit much more energy than the visible radiations. For
descriptive purposes, the therapeutic part of the ultraviolet spectrum may be divided into:
UVA: Wavelength 315400 nm
UVB: Wavelength 280315 nm
UVC: Wavelength below 280 nm
Production of Ultraviolet Radiations

Although ultraviolet rays are emitted by the sun but for therapeutic purposes, some form of
generator is used. Most of these generators produce ultraviolet rays from mercury. Various
types of generators are used such as high pressure mercury vapor lamp, Kromayers lamp,
fluorescent tubes, theraktin tunnel, PUVA apparatus, etc. for the production of ultraviolet
rays.
High Pressure Mercury Vapor Lamp

It consists of a U-shaped glass tube, filled with argon gas at a low pressure. Small amount
of mercury is enclosed in the tube and the tube is sealed at both the ends (Fig. 5.3).
Fig. 5.3: High pressure mercury vapor tube

U-shaped glass tube is used so as to act as a point source. The burner is made up of
quartz as this material allows the passage of ultraviolet rays and can withstand very
high temperatures with low coefficient of expansion. At the ends of the glass tube,
electrodes are placed, enclosed in metal caps across which a high potential difference
is applied.
Step-up transformer is used to apply high potential difference, i.e. 400 volts across the
two metal caps surrounding ends of tube to ionize the argon gas.
Once the argon has been ionized, normal mains voltage between the electrodes causes
the positive and negative particles to move through burner, constituting an electric
current. The electrons move toward the positive terminal and positive ions move toward
the negative terminal, collision between moving ions and neutral argon atom causes
further ionization and a glow of discharge is produced. Also, sufficient heat is produced to
vaporize the liquid mercury inside the tube and further ionization of mercury.
Thus, ultraviolet rays are produced by the process of argon ionization, mercury
vaporization and mercury ionization which takes about 5 minutes to reach its peak.
When the lamp is turned off, the ions of argon and mercury recombine so that within
the tube everything returns to its neutral state.
The tridymite formation: Some of the quartz changes to one another form of silica called
tridymite due to very high temperature in the burner. It is harmful to the total output
of ultraviolet rays as it is opaque to the rays and total output of the lamp gradually
decreases as the proportion of tridymite increases at around 1000 hours of ultraviolet
rays production that much tridymite can form that the whole burner tube needs to be
replaced.
A variable resistance is included in the burner circuit as a method of compensation and
resistance is reduced in order to increase the current intensity so as to produce adequate
ultraviolet rays.
The Kromayers Lamp

It has advantage over high-pressure mercury lamp that it can be used in contact with the
body tissues as the harmful infrared rays are absorbed by the circulating water so there is
no danger of burns.
Construction of Kromayers Lamp

The Kromayers lamp is a water-cooled mercury
vapor lamp which eliminates the danger of burn
and absorbs infrared rays. The high pressure
mercury vapor lamp is surrounded by circulating
distilled water so as to absorb infrared rays
(Fig. 5.4).
Kromayers lamp can also be used to treat
sinuses or deep body cavities. Direct contact
method can also be used as it minimizes the danger
of burn. Fig. 5.4: Section through the
Kromayers lamp
Fluorescent Tubes
Mercury vapor lamp has disadvantage that it produces a certain proportion of short
ultraviolet rays. Modern treatment methods often require the use of long waves ultraviolet
rays only without having short waves. In order to achieve this, fluorescent tubes are used.
Each tube is about 120 cm long and is made up of a glass which allows long ultraviolet
rays to pass. The inside of tube is coated with special phosphor. The spectrum of each tube
depends upon the type of phosphor coating.
A low pressure arc is set up inside the tube by the process of ionization. Phosphor is
used to absorb short wave ultraviolet rays and these are reemitted at longer wavelengths.
Accurate control of emitted wavelength is possible depending upon the type of phosphor
used.
Theraktin Tunnel
The Theraktin tunnel is a semicylindricular framework
in which four fluorescent tubes are mounted in its own
reflector in such a way that an even irradiation of a patient
is achieved (Fig. 5.5). Normally, fluorescent tubes with a
spectrum of 280400 nm are used.
PUVA Apparatus
Irradiation with UVA only, may be performed with special
fluorescent tubes which may be mounted in a vertical battery
on a wall or on four sides of a box totally surrounding the
Fig. 5.5: Theraktin tunnel
patient. This form of ultraviolet rays are usually given for
arrangement of fluorescent
two hours after the patient has taken a photoactive drug such
tubes
as Psoralen, hence the term PUVA (Psoralen-Ultraviolet-A)
is used.
Techniques of Application
Test dose: Individual patients reaction to the ultraviolet radiations is used to assess the test
dose. The technique of administering the test dose is very similar whether the Kromayers
lamp, fluorescent tube or theraktin tunnel is used. The only difference is of distance and
timings.
Calculation of test dose by air-cooled lamp: A suitable area of skin such as flexor aspect
of forearm is used for calculation of test dose. The skin is washed to remove any dust
or grease. Three differently shaped holes are cut with a material which is resistant
to the passage of ultraviolet rays such as card board, paper or lint. The size of the
middleholeis about 2 cm 2 cm with the hole on one side larger and on the other side
smaller.
A number of people are tested to find out average E1 time and distance by seeing a
erythema reaction. By knowing the average E1 (time and distance) for a particular lamp,
the duration of E2, E3 and E4 doses can be calculated.
E2 time = E1 time 2
E3 time = E1 time 5
E4 time = E1 time 10
Also, by inverse square law half the distance requires quarter the time for having the same
effect.
The cut out test paper or lint is applied to the patients forearm and the body is
screened. The middle hole receives the calculated E2 dose. The small hole receives an
exposure slightly longer than E2 and the larger hole receives an exposure slightly shorter.
The procedure is carefully recorded on the patients treatment card and all the three holes
are given to the patient to record when the erythema appears, how severe it is and how
long it lasts. The patients reaction will determine further dosages.
Calculation of test dose by Theraktin tunnel: Same procedure is used to calculate the test dose
as discussed above, however larger holes of about 4 cm 4 cm are used and are placed on
the abdomen. The rest of the body is screened.
Calculation of test dose by Kromayers lamp: Since the Kromayers lamp is used in contact with
the skin, the test dose is calculated by using very small holes, i.e. 0.25cm 0.25 cm and the
exposure time needs to be very short. Ultraviolet radiations can cause severe damage to
the skin; the only indication seen is the erythema reaction on the skin. The E1 dosage needs
to be carefully recorded and clearly marked on the treatment lamps.
Techniques of General Irradiation

1. The patients body part is washed to remove any dust or grease by soap and soaked
with a towel to remove any moisture.
2. The patient is explained about what is going on and how it will occur.
3. The patient is positioned in comfortable posture so as to allow the maximum exposure
of the part being treated and to avoid undue exposure of other parts.
4. A thin film of petroleum jelly (an effective screening agent) is used for soft structures
like lips, ear lobes, eyelids, nipples, navel, etc. A thick blanket is used to cover rest of
the body which does not need exposure. Eyes need to be protected by cotton wool or
goggles to avoid exposure.
Physiological Effects of Ultraviolet Radiations

Ultraviolet rays are absorbed by the skin which acts as protective layer. UVB and UVC
are absorbed by the epidermis whereas UVA may penetrate as far as capillary loops in
the dermis. The skin protects the underlined cells and intracellular structures from most
ultraviolet rays because the energy these rays release is sufficient to cause damage to the
cells and the intracellular structures.
1. Carcinogenesis: Sun can be called as a universal carcinogen. Prolonged exposure of
UVB or UVC can lead to carcinogenesis as these rays may affect DNA and thus cell
replication. The extent of carcinogenesis depends upon the wavelength of the ultra-
violet radiations and amount of ultraviolet rays absorbed. So, prolonged exposure of
patients skin to ultraviolet rays should be avoided and the course of treatment should
not exceed beyond four weeks.
2. Erythema: Damage to cells causes release of histamine like substance from the
epidermis and the superficial dermis. A gradual diffusion of this chemical takes
place until sufficient chemical has accumulated around the blood vessels in the skin
to make them dilate. The greater the quantity of histamine like substance, the sooner
and fiercer is the reaction. The erythema reaction is used to classify doses of ultra-
violet rays given to the patients. The erythema is produced by wavelengths shorter
than 315 nm.
3. Pigmentation: Pigmentation develops within two days of irradiation. Ultraviolet rays
stimulate melanocytes in the skin so as to produce melanin. The melanin covers the
nucleus of the cell to protect it from ultraviolet rays and forms an umbrella over the
nucleus of the cell. Pigmentation substantially reduces the penetration of UVB. The
extent of pigmentation varies from individual-to-individual and it is more in the dark
skin than in the fair skin.
4. Thickening of the epidermis: Sudden over-activity of the basal layer of the epidermis
causes a marked thickening, particularly of the stratum corneum (the outermost
layer). The thickening may occur to the extent that as much as three times its normal
thickness. The therapeutic doses may required to increase until desquamation has not
taken place.
5. Desquamation: The increased thickness of the epidermis is eventually lost by the
process of desquamation or peeling. When desquamation has taken place, the resistance
of the skin to the ultraviolet rays is substantially reduced.
6. Production of vitamin D: Vitamin D is necessary for the absorption of calcium and is
essential for the formation of bones and teeth. When ultraviolet rays are absorbed in the
skin, it converts 7-dehydrocholesterol into vitamin D. It helps reducing osteoporosis
and thus reducing fractures.
7. Effects on eyes: Strong doses of ultraviolet rays to the eyes can lead to irritation and
watering. Strong doses of UVB and UVC to the eyes can lead to conjunctivitis or slow
blindness.
8. Aging: The normal process of aging is accelerated if there is continuous exposure to
the ultraviolet rays. There is thinness of epidermis, loss of epidermal ridges, dryness,
loss of melanocytes and wrinkling due to lack of dermal connective tissue. Fair skin
races are at more danger than others. Persons taking sun-bath regularly should be
aware of harmful effects of ultraviolet rays.
9. Antibiotic effect: The increased body resistance to infection as a result of ultraviolet
rays are due to its action on reticuloendothelial system. Short ultraviolet rays can
destroy bacteria and some other small organisms such as fungi commonly found in
wounds. E4 dose effectively destroys such microorganisms.
Indications of Ultraviolet Irradiations

1. Wounds: The ultraviolet radiations are used for the treatment of infected and
noninfected wounds. For infected wounds, the effects of ultraviolet radiations are to
destroy bacteria, to remove infected dead material, to promote repair and to increase
healing. UVB rays are generally used by using Kromayers lamp with E3 or E4 doses.
For noninfected wounds, the effects of ultraviolet radiations are to stimulate the growth
of granulation tissue and to promote repair and to increase healing. UVA rays are
generally used by using some filter such as cellophane, etc.
2. Acne vulgaris: Acne is a chronic inflammatory condition of the skin which presents
with pustules, papules and comedones. It blocks the hair follicles and sebaceous glands
on the face, back and chest. An E2 dose of ultraviolet radiation may be given with the
following aims:
i. An erythema will bring more blood to the skin and so improves the condition of
the skin.
ii. Desquamation will remove comedones and allow free drainage of sebum, thus
reducing the number of lesions.
Also, it have a sterilizing effect on the skin. The intensity of dose needed, i.e. E2 + is
often painful and cosmetically not acceptable to the patient. Treatment is only palliative
and the condition usually returns within a few weeks of UVR. Unfortunately, it may
even appear to be worse a few weeks after UVR, as all the lesions in the skin reach their
peak at the same time, whereas in the normal course of acne some will be resolving
and others develop. Irregular rates of desquamation may restrict the frequency of
treatment and possibly produce a mottled erythema.
3. Pressure sores: Ultraviolet radiations are used for the treatment of pressure sores.
Pressure sores occurs due to any pressure injury which may vary from an area of
erythema to a deep seated ulcer exposing the underlying bone. Ultraviolet rays are
used to treat the pressure sores as described in wounds.
4. Psoriasis: Psoriasis is a skin condition in which there are localized patches on the
skin. It affects about 2% of population and the cause is unknown but thought to be
inherited. Formation of thick pink or red plaques sharply demarcated and covered
with silver scales are common features. The aim of the UVR treatment is to decrease
the proliferation by reducing the DNA synthesis. Treatment is given by using the
Goeckerman regimen, Leeds regimen or PUVA.
Goeckerman regimen: This consists of coal tar application 23 times a day with
general (total body) UVB radiation given once a day as a subthermal or E1 dose.
Leeds or Ingram regimen: In this the sensitivity of the patients skin is increased by
the local application of coal tar, added to the bath prior to the treatment. The psoriatic
lesions are covered with dithranol cream, which inhibits DNA synthesis. Next day the
dithranol is cleaned off, and the process is repeated. A suberythemal dose E1 is given
to the patient, using a Theraktin tunnel or a aircooled lamp at 100 cm. The dose is
repeated daily and is increased daily at a rate of 12.5%.
PUVA: Psoriasis is treated with ultraviolet radiations along with a sensitizer.
Sensitizing drug psoralen is given two hours before the exposure of UVA rays. This
inhibits the DNA synthesis and thus cell replication. Dosage of PUVA regimen
needs to be measured regularly. Dosage depends upon the patients skin type. Using
psoralen along with ultraviolet rays gives its name PUVA (psoralen ultraviolet A).
Long-term use can lead to skin damage and increases the risk of squamous cell
carcinoma.
5. Alopecia: Alopecia is premature falling of hairs leading to baldness. Alopecia is a
relatively common condition in which hairs falls out in patches. Suberythemal doses
of E1 are usually given for around 10 minutes daily. Individual patches can be treated
by E2 or E3 doses by Kromayers lamp twice a day.
6. Rickets: When ultraviolet rays are absorbed in the skin, it converts 7-dehydrocholesterol
into vitamin D. Vitamin D is necessary for the absorption of calcium and is essential
for the formation of bones and teeth. It helps reducing osteoporosis and thus reducing
fractures. It is beneficial in be-ridden, elderly patients or chronic debilitating patients
where chance of osteoporosis is more.
7. Counter-irritation effect: Ultraviolet rays are used to produce strong counter-irritation
effects over the site of deep rooted pain. An E3 or E4 dose is given to the area and is
then covered with dry dressing. Superficial pain produced by the erythema, mask the
deeper pain and also the modern pain gate theory also justifies this.
8. Psychological effects: UVR therapy also gives the patient a sense of general well-being.
Dangers of ultraviolet Radiations

1. Eyes: Eyes of the patient or the physiotherapist needs to be protected by goggles
from ultraviolet radiations otherwise there is a danger of conjunctivitis formation or
cataract to occur. UVB and UVC are absorbed by the cornea, but UVA is absorbed by
the lens and is implicated in the formation of cataract. Thus, wearing suitable goggle
is necessary from preventing any injury to the eyes.
2. Overdose: There are a number of factors due to which the patient can receive overdose
during treatment.
a. Too long the exposure: The duration of exposure needs to be accurate. A proper
timer with suitable audible sound and auto-cut device should be used.
b. Moving the lamp closure to the patient: This leads to exposure of larger doses to
the patient. Patient needs to be instructed not to move during treatment. Therapist
himself must calculate the distance by the application of inverse-square law.
c. Changing the lamp: It can also lead to overdose. Average E1 must be carefully
recorded and marked on every lamp. Care must be taken while using any new
lamp.
d. Use of sensitizers: Sensitizers must be administered and used carefully to avoid
any harmful effect.
Contraindications
1. Acute skin conditions: Certain skin conditions like acute eczema, dermatitis, lupus
erythematosus, or herpes simplex must be avoided irradiation.
2. Hypersensitivity to sunlight: Certain patients those who are hypersensitive to the
sunlight are also avoided irradiation.
3. Deep X-ray or cobalt therapy: Patients those who have taken deep X-ray or cobalt
therapy can have devitalization of the tissues. Hypersensitivity of the skin can
occur.
4. Skin grafting: Recent cases of skin grafting should not be given UVR.
Treatment of Patients Condition

1. Ulcers
2. Acne vulgaris
3. Pressure sores
4. Psoriasis
5. Rickets
6. General debilitating condition
7. Vitiligo
8. Alopecia
Sensitizers
ULTRAVIOLET RADIATIONS

Name
Age
Sex
Occupation
Chief complaints
Family history
Treatment history
Investigations
ii. Radiological testsX-rays, etc.
Use of sensitizerEgg, fish, alcohol, strawberry, insulin, coal tar
Any allergic reaction (e.g. Hypersensitivity to sunlight).
Hyperpyrexia
Hyperesthesia
Dermatitis
TB
Photosensitivity
Epilepsy
Renal or cardiac problems
Vascular impairment
Mental retardation
Use of sensitizers like insulin, etc.
4. Local contraindications.
5. General instructions to the patient:
Do not expose the area to sunlight
Do not use soap or water
Do not wash
Do not apply any cream or powder.
Laws of Radiations
Old dose (New distance)2
New dose =
(Old distance)2
Inverse square law: It states that the intensity of a beam of rays from a point source is
inversely proportional to the square of the distance from the source.
Cosine law: It states that the proportion of rays absorbed varies as per the cosine of the
angle between the incident and the normal. Thus, larger the angle at which the rays strike
at the body surface, lesser will be the absorption and vice versa.
Grothus law: It states that the rays must be absorbed to produce the effect and the effects
will be produced at that point at which the rays are absorbed.
Calculation of UVR dosage:
Suberythemal dose = E1 time
E2 dose = 2.5 E1 time
E3 dose = 5 E1 time
E4 dose = 10 E1 time
Degree of Erythema:
Disappears Appearance Duration
E1 6 to 12 hours (24 hours)
E2 4 to 6 hours 48 hours (2 days)
E3 2 to 4 hours 72 hours (35 days)
E4 2 hours 1 week
ULCERS
An ulcer is a loss of epithelial cells causing exposure of the underlying tissue.
Types
1. Venous
2. Arterial (ischemic)
3. Pressure sores.
Venous Ulcers
Sex : Women > men
Age : 5070 years
Site : Lower 2/3rd of the lower leg and on parts of the foot not supported by the shoe.
Predisposing Factors
Venous congestion associated with varicose veins or DVT
Occupations demanding prolonged standing
Poor personal hygiene and malnutrition.
Components of an Ulcer
Floor, Wall, Base
(E4), (E3), (E2)
Clinical Features
1. Floor of the ulcer (Part showing loss of tissue, exposing underlying tissues may be:
i. Pale and anemic with watery dischargeIndolent ulcer
ii. Green or yellow dischargeinfected ulcer
iii. Pink, purple with red spots granulating ulcer.
2. The wall of ulcer (Boundary between the floor and surrounding skin) may be:
i. Well-defined, straight, red and shinyulcer spreading
ii. Hard, edematous, over banging floorulcer chronic
iii. Shallow, sloping out from floor with bluish tingeulcer healing.
3. The base of the ulcer (Zone of the tissue immediately surrounding and underlying the
ulcer) may show.
i. Hardening, the extent varies according to severity and duration of the ulcer.
ii. Pigmentation due to breakdown of red blood cells
iii. Poor circulation.
iv. Coarse skin texture with heavy heading or papery thin and eczematous tissue.
4. Edema of the base of the ulcer of foot and ankle to the shoe line.
5. Considerable pain around the ulcer, especially if infected, pain increased on walking.
6. Limited movement of the feet and ankle.
7. Muscle weakness and atrophymainly calf muscles with loss of pumping action.
8. Walking pattern poor with no push off.
Treatment
Conservative: Aims to relieve pain, relieve congestion and reduce edema, improve
general circulation to lower limb, mobilize the joints and strengthens lower limb muscles
(especiallycalf), improve condition of skin of lower leg.
Soft tissue techniques
UV rays.
For Infected Ulcer

Base of the ulcer: E2; edges are screened with clamp. Sterile gauze, this is repeated two
or three times a week. If the edges are clear of infection, a E1 may be given to edges and
surrounding skin to promote healing.
Effect: To promote granulating tissue.
For indolent: E4 is given to the floor with ulcer-screened and to the edges of the surrounding
skin.
Effect: To stimulate the circulation
Ultrasound (Contraindicated in DVT)
0.250.5 W/cm2 for 510 min
For small area: pulsed beam
For large area: continuous.
Ultrasound is given with coupling cream to the surrounding skin or in a sterile saline.
Both to the ulcer as well as to the surrounding area. Also,
Pulsed electromagnetic energy (PEME)
Laser
Support and pressure (compression bandage)
Active exercise:
Complications: Superficial and Deep VT
Arterial (ischemic ulcer)
Sex : Men and Women
Age : Elderly
Site : On toes, foot and heel (may be on lower leg)
Cause : Lack of nutrition to the skin due to inadequate arterial blood supply.
Clinical Features
Floor is pale, anemic and liable to infection, surrounding skin may be normal or ischemic.
Distance: 36
Dosage:
BaseE2
WallE3
FloorE4
ACNE VULGARIS
This is a chronic inflammatory disease of the sebaceous glands.
Age: It starts between 9 and 17 years, is associated with puberty, and is generally clear by
30 years.
Sex: Males > females.
Site: Face, chest and upper back.
Puberty
Lack of fitness, exercise without fresh air
Poor health, constipation
Diet high in butter, cream, sugar, chocolates or alcohol
Sweating
Endocrine abnormalities involving testosterone
Anxiety
Skin typedark complexion, heredity.
Etiology: Propionibacterium acnes.
Pathology
Sebum production and keratin blocks the pilosebaceous duct and hair follicle. The exposed
surface becomes oxidized and blackened the walls of the follicle and inflammation takes
place. This causes swelling and distension of the follicle and duct by bacteria causing pus
formation (Pustule). Once the pus is discharged the duct and follicle shrink and healing
takes place. But repeated attacks can result in scar tissue formation.
Clinical Features
Comedones, papules (reddened round raised areas), pustules (yellow raised areas
surrounded by reddish purple area), cysts scars can occur.
Management
Topical: Sulphur-based ointment, salicylic acid-based ointments, benzoyl peroxide gel.
General: Antibiotics
Patients positioning:
Sitting position: Two pillows Back of the head
Neck line and head line maintenance
Remaining part must be covered
Wearing cotton wool on the eyes.
Physiotherapy
a. UVR: Spectrum 190 to 390 nm
Distance: 18
Dose: E2 dose
Position of the patient: Sitting on stool with back supported on wall. Wash the affected
areas at least twice a day with oil-free soap and rinse with cool water.
Focusing point: Tip of the nose.
Dosages depend upon the patients weight and patient skin type.
PRESSURE SORES
Pressure sore is a term used to describe any pressure injury which may vary from an area
of erythema to a deep seated ulcer exposing the underlying bone.
Age : At any stage
Sex : Equal
Site : Heels, buttock, hips, elbowspressure area
Cause : External Factors Postoperative pain, immobility, unconsciousness, prolonged
bedrest.
Internal factors Muscle tone, incontinence, diabetes, trophic ulcer.
Clinical Features
Floor of sore Pink, vascular or filled with infected exudates, cavity may be shallow or
deep with loss of subcutaneous tissue and exposure of bone.
Around the cavity Skin is red or blue. If sensory nerve endings are not destroyed
Pain will be there.
UVR Treatment
Positioning of the patient: Oblique side lying (45)
Dosage: FloorE4 dose
WallE3 dose
BaseE2 dose
Distance: 36
PSORIASIS
Psoriasis is a chronic inflammatory disease of the skin characterized by clearly defined dry
rounded red patches with silvery scales on the surface.
Age: Common age is 1530 years
Sex: Equal
Climate: The condition is worse in damp, cold climate.
Heredity
Infection (after upper respiratory tract infection)
Trauma (Mechanical friction, cuts, stings)
Anxiety (often appear in relation to mental stings, e.g. bereavement, exams)

Drugs (e.g. chloroquine precipitate this)
Arthropathy.
Cause
Cause is unknown, in normal skin the maturing of epidermal cells takes 2129 days in
psoriasis; this is accelerated to 4 days.
Distribution: Elbows, knees, back and sacrum.
Clinical Features
Sharply defined red and pink areas
Plaques
Silvery scales.
Treatment
Psoriasis can be treated with UVR. Two sources are used the theraktin and PUVA:
1. The theraktin: This is usually in the form of a tunnel with four fluorescent tubes. The
patient is generally naked and lies supine for half the treatment session and prone for
other half. It may be used alone or in conjunction with coal tar on diatermal.
Suberythema dose is given daily or 3 times a week. Prominent parts have a mild
erythema, but fades before the next treatment.
2. PUVA: This is psoralens plus UVA. Psoralens are photosensitizing substances, which
occur in plants such as parsley, parsnips and celery. The one used for psoriasis is
8-methoxypsoralen (8-MOP).
Methods: Patient takes 86 tablets of psoralens with milk two hours before exposure.
Posture upper trunk Midpoint of line joining the inferior angles of the scapula
Post lower trunk Midpoint of line joining the 2 popliteal fossa
Right side Right greater trochanter
Left side Left greater trochanter
UVA doses in PUVA treatment:
I. Always burns, never tan
II. Always burns, then slight tan
III. Sometimes burn, always tan
IV. Never burn, always tan
V. Lightly pigmented
VI. Black
Precaution: To patient on PUVA
Do not take psoralens on empty stomach
Protective goggles are essential polaroid sunglasses must be worn from the time of
taking the psoralen to at least 12 hours after treatment.
Stop using all ointments during PUVA

If the skin is dry, simple oil or lubricating lotions may be used.
During the treatment, if the patient feels pain, the Physiotherapist must be called
immediately.
Aims of ultraviolet radiations
To decrease the rate of DNA synthesis in the cells of the skin and thus slow down their
proliferation.
Dosage: Suberythemal dose (half E1)
Distance: 36
Positioning of the patient: Oblique side lying.
1. General: Focusing point
a. Umbilicus (Supine lying)
b. Midpoint between the posterior SI spines prone lying
2. Fractional: Edibase tech.
Body is divided into 6 parts
Focusing points:
Anterior upper trunkXiphisternum
Anterior lower trunkMidpoint of line joining two patella.
RICKETS
Rickets is a disease of disordered calcium metabolism occurring in infants and young
children. The most characteristic changes taking place in the bones.
Type of Rickets
1. Nutritional rickets: This is due to deficiency in the diet and occurs in children below 4
years.
2. Celiac rickets (Intestinal diminished):
This is due to diminished absorption of calcium from the intestines in celiac disease
and other malabsorption disorders.
3. Renal rickets: This is due to various types of defects in the renal function in children
above 5 years.
Positioning of the patient: Oblique side lying (45 inclination)
Dosage: Suberythemal dose.
GENERAL DEBILITATING CONDITION

Positioning of the patient: Oblique side lying.
Dose: Suberythemal dose.
VITILIGO
Vitiligo is a condition in which the areas of the skin are depigmented owing to the loss of
normal melanocyte function.
Treatment: Aim is to produce pigmenting of the abnormal areas. PUVA is very successful.
The psoralens may be taken by mouth or painted on to the affected areas. The psoralens
used may be Trimethyl Psoralens (TMP).
If UVA source is not available, UVB from the theraktin can be successful. Suberythema
dose should be tried one or two times per week for 68 weeks.
ALOPECIA
Absence or premature loss of hair.
Classification
Alopecia areata Loss of scalp hair
Alopecia totalis Loss of all scalp hair and eyebrows
Alopecia universalis Total loss of body hair.
Etiology
Age: Under 30 years
Sex: Equal
Predisposing factorsgeneral anxiety, fatigue, poor health, heredity.
Treatment: Aims are to improve general health.
To improve nutrition to the hair follicles.
General Health
Suberythema or E1 dosage is given daily for 68 treatments.
Promotion of nutrition (Kromayer):
E2 or E3 dosage
Dose for alopecia: E2 dose.
SENSITIZERS
1. Thiazide Diuretics:
Doburil, Aldoril, Enduron
2. Sulphonamides:
Thalazole, Furadentin, Gantrisin
3. Tetracycline:
Terramycin, Achromycin, Panmycin
4. Antifungal Agents:
Griseofulvin
5. Hypotic Drugs:
Veronal, Sulphonal, Benzodiazepines
6. Barbiturates:
Phenobarbital, Allobarbital, Barbital
7. Phenothiazine:
Tranquilizer, Melleul, Steiazine
8. Gold therapy
9. Various hormonesInsulin, thyroid extracts
10. Aspirin and derivatives
11. Psoralens (8-methoxypsoralens)
12. Coal tar
13. Diathranol
14. Eosine
15. Strawberry, lobster.
6 Laser Therapy
The word LASER is an acronym for Light Amplification of Stimulated Emission of

Radiation. It refers to the production of a beam of a radiation which differs from the
ordinary light in several ways. These are nowadays used in laser light shows, compact
disk players, surgical incisions, in ophthalmology and gynecology, etc.
Historical aspects: The great German physicist Max Planck in 1900 presented an explanation
of why colors of glowing hot bodies changes with temperature. He proposed the quantum
theory according to which radiations are discrete quantities or packets of energy. Einstein
in 1970 outlined the principles underlying the production of laser radiation as a part of
quantum theory. In 1960, Dr Theodore Miaman of Hughes laboratory of USA produced
the first burst of ruby lasers. Later, the workers of Bell telephone laboratory produced a
helium neon laser. They also developed carbon dioxide laser which became popular for
surgical applications. More recently, the potential clinical use of nonthermal effects of the
laser on the tissues came into existence. This therapy got a boost in 1979 by the invention
of semiconductor diode laser-gallium arsenide laser (Figs 6.1 and 6.2).
Properties of laser: The laser differs from the ordinary light in the following ways:
1. Monochromaticity: This means that the laser light has a single color (mono-single,
chromaticitycoloration). This is because the lasers are of a single wavelength and
thus the definite frequency. Ordinary light however has many wavelengths.
Fig. 6.1: Laser therapy

Laser Therapy 227
Fig. 6.2: Scanning electrode
2. Coherence: Laser radiations are not of the same wavelength but also has same phase.
Coherence means similar or synchronous behavior of laser beam. This means two things
simultaneously. First, the laser beam is temporarily coherent, means that the photons
are in same phase with crests meeting crests and troughs meeting troughs in time.
Secondly, the laser beam is spatially coherent, means the photons are unidirectional
and stay in same phase over long distances and little spread of beam. Ordinary light
on contrary has variable wavelengths.
3. Collimation: Laser beams remain collimated that means they remain in parallel. They
do not diverge much and the energy can be propagated over a larger distance.
Production of Laser
It is recalled that the electrons of an individual atom remain as a cloud of negative charge
around the positive nucleus. According to the quantum theory, the electrons can only
occupy certain energy levels or shells around the nucleus. Under normal circumstances,
in the vast majority of the atoms the electrons remain at the lowest energy level, i.e. at the
resting or ground state. If enough energy is added to atom, an outer electron may gain
sufficient energy to free itself from the nucleus. The atom then becomes a positively charged
ion and the electron becomes a free negative charge. When the outer electrons are in one of
the higher energy states, they will tend to return to a lower energy state, sometimes to the
most stable or ground state. Also, the quantum energy which is expressed in electron volts
is inversely proportional to the wavelength. This means the greater the quantum energy;
the lesser will be the wavelength. A large number of atoms with the electrons in the excited
state can lead to amplification since one photon releases a second and these two can release
more and so on.
Components for laser production

For the production of a laser radiation, the device must consist of the following components:
1. Lasing medium
2. Resonating chamber
3. Energy source.
1. Lasing medium: The material which is capable of producing laser is known as lasing
medium. It can absorb energy from the external source and then gives off its excess
energy as photons of light. Lasing medium could be solid crystal or semiconductor,
liquid or gas. The lasing media in low intensity laser or cold laser are either helium-neon
(He-Ne) or semiconductor, i.e. gallium-arsenide (Ga-As).
2. Resonating chamber: The resonating chamber contains the lasing medium which
is surrounded by two parallel mirrors at either ends. One of the mirrors has 100%
reflectance while the other has slightly less reflectance. The mirror with slightly less
reflectance serves as an output device which allows some of the photons to escape
through it.
3. Energy source: A flashgun is used to excite the electrons of the lasing medium. The
source of flashgun is usually current electricity.
Types of Laser
The various types of laser are available nowadays. The commonly used lasers are:
1. Ruby laser (or crystal laser)
2. Helium-neon laser (gas laser)
3. Diode laser (or semiconductor laser).
Ruby Laser (Crystal Laser)

Ruby laser is also known as crystal laser because it contains synthetic ruby as a lasing
medium. Synthetic medium (aluminium oxide and chromium) are used rather than
the natural one to ensure purity of the medium which is necessary to generate physical
characteristics of laser. Aluminium oxide with trace of chromium oxide forms a 10 cm
long and 1 cm wide synthetic ruby rod. A helical electric discharge tube containing xenon
tube is wound around the ruby rod. Both the ends are made reflecting by silvering the
surfaces with one end as 100% reflective and other slightly less. The xenon tube is used to
give intense flash of white light which excites the ruby molecules and raises the electron
to a higher energy level. As the excited state is unstable, the electrons return to ground
state by releasing a photon. This is known as spontaneous emission. The rate of supply of
energy exceeds to a greater extent which leads to a large number of atoms at higher energy
levels. This is known as population inversions. Atoms in their excited state are encountered
by the photons and this leads to further stimulated emissions. The excited electron falls
to its resting state and gives off a photon of exactly the same energy as that of photon
which collided with it (photon of 694.3 nm wavelength). Hence, a beam of red laser with a
wavelength 694.3 nm is emitted.
Helium-neon Laser (Gas Laser)

Gas laser consists of a mixture of primarily helium and neon in a low pressure tube. This
low pressure tube is surrounded by a flashgun which excites the atom to a higher energy
level. Thus, photons released by the spontaneous emission and have a wavelength of
632.8 nm. These photons reflect to and fro to the tube and collide with the atoms of higher
Laser Therapy 229
energy levels. This leads to stimulated emission with the release of similar photons. Intense
beam of light emerges from the narrow partially transmissive which is red in color and has
a wavelength of 632.8 nm.
Diode Laser (Semiconductor Laser)

Gsallium and arsenide are used as a diode or semiconductor to produce an infrared
invisible laser with a wavelength of 904 nm. In these with an external electric potential,
positively charged holes are thrown from the p-type gallium-aluminium-arsenide layer
into the active layer of gallium-arsenide. The negatively charged electrons interact with the
active layer and thus photon of light is released. The photons are reflected to and fro and
emitted as a laser beam from one partially transparent end. By varying the ratio of gallium
to aluminium, desired specific wavelengths are obtained. The advantage of semiconductor
laser diode is that these can either emit a continuous or a pulsed output.
The method of application of laser therapy is quite simple. Generally, the laser energy is
emitted by a hand held applicator for therapeutic purposes. The gallium-arsenide laser
contains the semiconductor or diode element at the tip of the applicator, whereas the
helium-neon laser contains their components inside the unit and delivers the laser light to
the target area via a fiberoptic tube. This causes divergence of the beam. To administer the
laser for therapeutic purposes, two methods are generally used:
1. Grid method
2. Scanning method.
1. The grid method: The treatment area is divided into a grid each of 1 square cm. The
hand held applicator should be in light contact with the skin and directly perpendicular
to the target tissue. Each square cm is stimulated for a specific period of time.
2. The scanning method: No contact is made between the tip of the laser and the patients
skin. The tip of the applicator is held at a distance of 5 to 10 mm. Since the divergence of
beam occurs, there is a decrease in the amount of energy applied as the distance increases.
Dosage Parameters
1. Wavelength: Wavelength depends on the lasing medium used. For superficial
conditions like wounds and ulcers, visible red laser is used. For deep conditions of
muscles and bones, infrared laser is used. Cluster probe laser having several diodes
are used for the larger area of soft tissues.
2. Power: The power output is measured in watts. Since the power output of laser beam
used therapeutically is quite small, mW is generally used. Moreover, percentage of
power output is sometimes used, i.e. 10, 20 or 30% of the total power output.
3. Energy: The energy delivered to the treatment tissue is expressed in Joules. It is
calculated by the following equation:
Energy (in Joules) = Power (in watts) Time (in seconds)
Sometimes, when the energy required for the treatment of a particular tissue is known
and the power output is available then the total treatment time can also be calculated.
4. Power density: Power density decreases as the area between the tip of the applicator
and the part to be treated increases. Power density is expressed as:
Power density = Incident power/area in cm2
Total power used therapeutically is thus calculated by the inverse square law.
5. Energy density: Energy density can be calculated as:
Power (W) Time (sec)
Energy density =
Area (in cm2)

The dosage in laser therapy is calculated in terms of energy density applied which is
expressed in joules/cm2.
Interaction of Laser with Body Tissues

Low intensity lasers are used therapeutically for their nonthermal effects. Visible radiations
are remarkably absorbed in the hemoglobin whereas infrared light is strongly absorbed
by water. Absorption results in the transformation of energy in the body tissues. Human
body consists of 70% of water and 30% of organic material. Organic material which
absorbs visible light contains chromophores. Chromophores are defined as the molecular
structures which get excited by the visible spectrum due to its configuration. In human
body, hemoglobin and melanin contain chromophores and thus absorbs laser energy.
Physiological Effects and Therapeutic Uses of Laser

1. Wound healing: Laser therapy is nowadays being effectively used for the treatment
of wounds. Healing of wounds is thought to accelerate by the application of
laser (Dyson & Young, 1986). It is a complex physiological process which involves
chemotactic activity, vascular changes and the release of chemical mediators. Radiations
particularly from the red spectrum of light are found effective in the treatment of
chronic ulcers. Both untreated chronic ulcers as well as trophic ulcers can be very
effectively treated by laser therapy. Laser therapy increases tissue proliferation and
thus enhances wound healing caused due to burns, surgical incisions, diabetic ulcers
and pressure sores. Both direct contact or grid method as well as scanning method
is effectively used for healing of wounds. Wound margins are effectively treated by
direct contact technique. For doing this, the laser probe is usually applied at 1 to 2 cm
from the edges. Dosage of 4 to 10 joules/cm2 is usually sufficient.
Treatment of wound bed is preferably done by noncontact method. The dosage
from 1 to 5 joules/cm2 is usually sufficient for the treatment of wound bed. The low
dosages are usually sufficient because the protective layer of dermis is absent in this
area.
2. Tensile strength and scar tissue: The tensile strength of the tissues treated with laser
therapy is more than the normally healed ones. This tensile strength is directly related
to the increased levels of collagen. Collagen synthesis and thus the tensile strength are
Laser Therapy 231
fibroblasts mediated functions which are improved significantly by the treatment of

laser.
Also, the wounds exposed to laser therapy have more epithelialization and less
exudate formation. Hence, they have less scar tissue formation with a better cosmetic
appearance.
3. Musculoskeletal conditions: The laser therapy is found to be very effective in various
overuse tendinitis or bursitis conditions like tennis elbow, golfers elbow, supraspinatus
tendinitis, etc. Also laser therapy is found effective in some acute conditions like ankle
sprain as it enhances the healing process and relieves pain.
Various arthritic conditions like rheumatoid arthritis, osteoarthritis, ankylosing
arthritis, pyogenic arthritis, etc. are benefited by the use of laser therapy. Laser has
its effect on prostaglandin synthesis and thus it relieves inflammation. Laser is found
to be very effective in the healing of the connective tissues and thus is effective in the
treatment of various arthritic conditions.
Laser therapy has bactericidal effects because of increased phagocytosis by leuko-
cytes. When used in conjunction with antibiotics, laser therapy is found effective in the
treatment of various inflammatory conditions.
4. Pain relief: Laser therapy is found effective in relieving pain, both acute as well as
chronic. Acute pain as in ankle sprain is relieved by the laser by reducing swelling and
enhancing the healing process. Many musculoskeletal pains as in fibrositis or trigger
pain are relieved by the application of laser on trigger points or acupressure points.
In postoperative conditions also, the laser is found effective in the enhancing healing
process and thus reducing pain. Analgesia is achieved in certain neurogenic conditions
also. Pain due to trigeminal neuralgia is found to be relieved by laser therapy. Studies
on superficial median or radial nerve conduction velocity have shown a decrease in
sensory nerve conduction velocity by a low intensity laser.
5. Bone and articular cartilage: Studies on the effects of laser on bones and articular
cartilage is increasing day-by-day. It has been found that the longer duration of low
power laser helps in fracture healing and bone remodulation. It helps in chondral
proliferation and remodeling of the articular line. It has also been found useful for the
treatment of nonunion of fractures.

1. Effects on eyes: The main danger of low power laser therapy is a risk of eye damage if
the beam is applied directly into the eye. So, to avoid the exposure of eye with a beam of
laser, protective goggles should be worn by the patient as well as by the physiotherapist.
2. Effects on cancerous growth: The laser should not be applied over the area of cancerous
growth. Laser acts as a photobiostimulatory agent, its exposure to cancerous tissue can
lead to acceleration of its growth and metastasis.
3. Effects on pregnant uterus: Laser should not be applied directly over the pregnant
uterus as it may cause abnormal growth.
4. Effects on infected tissues: When treated in contact with the infected tissue, the laser
head needs to be cleaned thoroughly or sterilized. It should be used preferably in
conjunction with ultraviolet therapy for the treatment of infected wounds.
5. Hemorrhagic areas or cardiac conditions: Laser can cause vasodilatation and hence,
care should be taken while exposing any hemorrhagic area. Patients of certain cardiac
conditions are avoided the exposure of laser therapy around the cardiac region.

1. Tennis elbow
2. Supraspinatus tendinitis
3. Golfers elbow
4. Plantar fasciitis.
Proforma for patients assessment

Name
Age
Sex
Occupation
Chief complaints:
Family history
Treatment history
Investigations:
Hyperpyrexia
Hypertension
Epileptic patients
Noncooperative patients
Laser Therapy 233
Menstruation
Pregnant uterus
Hemorrhage and infected tissue.
4. Checking for local contraindications
Skin conditions
Tumor
Neoplastic tissue.
5. Preparation of trays
Two test tubes
One with hot water
Cotton
Goggles
Towels
Pillows
Sandbags.
6. Preparation of apparatus: The laser apparatus is conveniently positioned. Protective
goggles designed for the particular wavelength being used, are worn to avoid any risk
of accidental application of laser beam into the eye.
Selection of treatment head
Switching on
Regulation of power
Checking the plugs
Checking the socket
Checking the main wire whether it is properly fitted in the main machine
8. Positioning the patient: Comfortable with good support.
9. Treatment:
Placing the applicator
i. Warn not to remove goggles
ii. Not to move
iii. Not to touch the machine
iv. Not to sleep.
10. Application: Maintain the laser applicator so that beam is at right angles in order to
achieve maximal penetration. Contact may be made. Do not switch on the applicator
before application of applicator to the skin.
11. Termination: Switch off before removing the applicator from the skin contact. Imme-
diate increase or decrease of pain needs to be recorded.
12. Other points:
Record of treatment.
Tennis Elbow (Lateral Epicondylitis)

Definition
Tennis elbow is a condition characterized by pain and tenderness on the lateral side of the
elbow, usually related to the common extensor tendons of the forearm.
The condition is common in both the sexes almost equally and age of occurrence is
between 3045 years.
Etiology
Excessive use of wrist extensors as in:
i. Repetitive overuse activity like squeezing clothes
ii. Wrong technique at sport
(e.g. tennis, golf, badminton, fencing)
iii. Unaccustomed gardening or carpentry.
Pathology
Tear occurs at tenomuscular junction, in the tendon or at tenoperiosteal junction. The
resulting inflammation forms to heal the torn tissue. If excessive fibrin is formed, fibrous
tissue will result in adhesions the tendon and neighboring tissue. This causes pain and
repeated injury to tendon prevent healing and excessive scar tissue form.
Clinical Features
1. Pain on exertion
2. Pain over the elbow to the wrist.
3. Resisted wrist extension is painful, passive movement is pain-free.
4. Tenderness over the tendon.
Treatment
Acute:
1. Ice towel for 20 minutes
2. Rest
3. Splint for wrist extension for 2 to 8 weeks
4. Strapping.
Modalities Used
1. Laser
2. Pulsed electromagnetic energy
3. Friction massage for 510 minutes for 4 days.
Position of Patient
Sitting on chair with elbow supported and semiflexed.
Laser Therapy 235
Position of Therapist
Standing/sitting by the side of patient.
Treatment Dosage
Energy density should be 0.51 J/cm2.
Supraspinatus Tendinitis
History
This may occur as a result of accident (e.g. a fall on the shoulder), over exercise (e.g.
aerobics) or a series of minor stresses (e.g. long periods of writing).
Clinical Features
Pain: Toothache type pain is present radiating from the acromion process to the deltoid
insertion.
Painful Area:
1. Abduction to 60 degree is pain-free.
2. 60 degree to 120 degree is painful.
3. 120 degree to 180 degree is pain-free.
Movements
Shoulder arm movements are full (but have a painful arc).
1. Resisted abduction in outer range in often painful.
2. Lowering the arm from elevation is very painful. If this movement is resisted then pain
is less.
3. Reversed glenohumeral rhythm, the scapula moving more than the humerus.
Functions
Severely limited in patient who has to carry weights (e.g. dresses on coat hangers).
Standing by the side of patient.
Position of Patient
Side lying/sitting with the arm supported over a pillow.
Treatment
Energy density should be 4 J/cm2.
Golfers Elbow (Medial epicondylitis)

Definition
This is a condition characterized by pain and acute tenderness on the medial side of the
elbow. It affects the common flexor origin.
Principles of treatment are same as for tennis elbow.
Treatment
Energy density should be 1 J/cm2.
Pain is produced by extension of elbow, supination and valgus strain.
Position of Patient
Sitting or supine lying with shoulder of the affected arm abducted.
Standing or sitting by the side of patient.
Plantar fasciItis
Definition
This is a common cause of pain in the heel. It occurs as a result of inflammation of the
plantar aponeurosis at its attachment on the tuberosity of the calcaneum.
The pain is worse in the morning and often reduces with the activity.
On Examination
There is marked tenderness over the medial aspect of the calcaneal tuberosity, at the site of
attachment of the plantar fascia.
Investigation
X-ray often shows a sharp bone spur projecting forwards from the tuberosity of the
calcaneum.
Treatment
Rest
Analgesics
Soft heel pad made up of MCR (Microcellular Rubber)
Local corticosteroids
Laser therapy.
Energy density of 4 J/cm2 is usually sufficient.
Superficial Heating
7 Modalities
paraffin waX bath therapy

Paraffin wax bath therapy is an application of molten paraffin wax over the body parts.
The temperature of the paraffin wax is maintained at 4044C, whereas its melting point is
5155C. If the molten wax at 5155C is poured on the body parts, it may cause burn over
the body tissues, that is why some impurity is added to lower down its melting point such
as liquid paraffin or mineral oil. Paraffin wax bath therapy provides about six times the
amount of heat available in water because the mineral oil in the paraffin lowers its melting
point. The combination of paraffin and mineral oil has low specific heat which enhances
the patients ability to tolerate heat from paraffin better than that from the water of the
same temperature. The composition of solid wax: liquid paraffin: petroleum jelly is 7 : 3 : 1
or solid wax : liquid paraffin or mineral oil is 7 : 1. The mode of transmission of heat from
paraffin to the patient skin is by means of conduction.
Paraffin Wax Bath Unit

Parts of a typical Paraffin wax bath
unit are stainless steel container,
mains, thermostat, thermostat pilot
lamp, power pilot lamp, lid and caster
(Fig. 7.1).
Initially, heating is quicker
with this type because there is no
water jacket to be heated. Container
contains wax and paraffin oil. Mains
function is to switch on or off the
heating element, which is located in
the casing of paraffin wax bath unit.
Thermostat keeps the tempera-
ture fixed or static in the range which is
adjusted with knob. Thermostat pilot
lamp indicates whether thermostat is
on or off.
Power pilot lamp function is to
show whether power is on or off. Fig. 7.1: Paraffin wax bath unit
Lid covers the container and caster allows the paraffin wax bath container to be moved
from one place to another.
Methods
The part to be treated must be cleaned with soap and water. Moisture is to be soaked with
towel. Position of the patient should be such that the part to be treated comes closer to the
wax bath container. Before application one must ensure that there should be no moisture
over the body tissues otherwise burn could occur. The warm wax is placed on body tissues
by various techniques and the treatment is given for about 1020 minutes.
Techniques of application
Various techniques used for the application of paraffin wax are as follows:
1. Direct pouring method: The molten wax is directly poured by a mug or utensil on
the part to be treated and then wrapped around by a towel. The wax is allowed to
solidify for about 1012 minutes. Several (46) layers can be made over the body
tissues.
2. Brushing method: A brush of various sizes (4 or 6) is used for the application of
molten wax over the body tissues. Several coats (46) are applied over the body tissues
and wax is allowed to solidify and wrapped over by a towel.
3. Direct immersion or dipping method: In this method, the body part to be treated
is directly immersed into the container of paraffin wax and taken out. Once the wax
solidifies, the part is again immersed to make another layer of paraffin wax and
wrapped around by a towel.
4. Toweling or bandaging method: A towel or a roll of bandage is immersed in molten
paraffin wax and then wrapped around the body part. Several layers can be made
over the body part. This method is preferably used for treating proximal parts of the
body.
Once the treatment is given by paraffin wax, it can be reused for the next session.
Regular cleaning or changing of the wax is necessary to ensure good hygiene.
Effects and Uses

Paraffin wax bath therapy provides superficial heating to the tissues. It increases the local
circulation to the area, increases the pliability of the skin, and reduces stiffness and thus
pain.
Indications
Paraffin wax therapy is used for the treatment of:
i. Rheumatoid arthritis
ii. Osteoarthritis
iii. Joint stiffness, adhesions
iv. Post immobilization stiffness, scars on the skin, etc.
Superficial Heating Modalities 239
Contraindications: Paraffin wax bath therapy should not be used in the cases of:
i. Open wounds
ii. Skin rashes
iii. Allergic conditions
iv. Impaired skin sensation
v. Defective arterial supply, etc.
Maintenance of Paraffin Wax Bath Unit

Sterile the paraffin wax bath by heating it to 212 Fahrenheit. For reuse, sterilization should
be done frequently. Drain the melted paraffin wax, filter it out and replace it back for reuse.
Change the wax at least once in 6 months.
Proforma for patients assessment

1. Receiving the patient
2. Knowing details about the condition
3. Preparation of traysTwo test tubes:
One with cold water
One with hot water.
Pillows, towels, sandbags.
4. Preparation of apparatus: The temperature of the wax is checked.
Preparation of patient: The nature of wax treatment is explained and the area to be treated
is cleaned and soaked with towel. Any moisture on the area needs to be removed to avoid
burning.
Correct positioning of patient: The patient is positioned in such a way that the part to be
treated comes in close proximity to the wax bath container.
Checking for contraindications:
Open wound
Ischemic disease
Buergers disease
Fungal infection, e.g. paronychia.
Acute dermatitis and eczema.
Testing skin sensation: Two test tubes are used, one with hot and other with cold water.
Part to be treated, needs to be checked for its intact sensation before treatment.
Treatment
1. Checking the apparatus: Check whether thermostat is working properly.
2. Application: Various methods of applications are used. Each must be followed as
explained earlier. Wax is allowed to cool and can be reused for the next treatment session.
Termination: The patients skin should be inspected for any burn.
HOTPACKS/HYDROCOLLATOR PACKS
Hot packs are the packs which are immersed
in an apparatus called hydrocollator
(Fig. 7.2). They provide superficial moist
heat to the part where applied. They contain
the substance which absorbs heat like silica
or gel. They are stored in a thermostatically
controlled water bath inside the equipment.
The temperature inside the hydrocollator
ranges between 6580C. The aim of the
hydrocollator pack is to rise the body
temperature at 4045C.
Hydrocollator packs are available in
various sizes and shapes (Figs 7.3A to C). The
size and shape of pack should be chosen on
the basis of area being treated. The common
sizes are small (for smaller joints like elbow,
ankle), large (for large joints like hip and
back), contoured (for cervical spine).
When used, hydrocollator packs are
taken out of apparatus by means of tongs
and wrapped inside a towel. Six to eight
Fig. 7.2: Hydrocollator
layers of towel is made around the pack.
The total treatment time is around 8-10
minutes.
Effects and Uses

1. Effect on muscular spasm: The most important physiological effect of hot pack is that
it relieves the muscular spasm very quickly. Moist heat provided by the hydrocollator
pack is beneficial for relieving the muscular spasm.
2. Local rise in temperature: The rise in local body temperature occurs following hot
packs application. The heat is transferred by means of conduction from hot packs
to skin and superficial tissues. Local rise in temperature has many effects including
increasing circulation, relieving spasm and thus relieving pain.
Figs 7.3A to C: Hydrocollator hot packs

3. Increase of local circulation: The local circulation around the area is also increased.
It provides fresh supply of blood and nutrition. It reduces the waste products of
metabolism from the area.
4. Skin and connective tissue: Skin becomes supple and elasticity of connective tissue is
also increased when combined with stretching.
5. Relieve of pain: Pain is relieved by application of hot packs. Pain relief following hot
pack application may occur due to decreased nerve conduction velocity or elevated
pain threshold. It may be due to sedative or counter irritation effect by heat. Pain relieve
may be associated with relieve of muscular spasm and increase in joint range of motion.
Contraindications
The hot packs should not be used in the area of:
i. Impaired skin sensation
ii. Open wounds
iii. Recent hemorrhage
iv. Skin allergy
v. Impaired circulation.
ELECTRIC HEATING PADS

Electric heating pads are used to provide raised temperature of 4045C to the body parts.
It contains an electric heating element inside it and is regulated by a resistor or rheostat.
They provide superficial heat to the part where applied. The transmission of heat is by
means of conduction.
The main advantage of using electric heating pads is that they can be used at home by
the patients themselves and are cheaper and flexible.
Electric heating pads are available in various sizes and shapes. The size and shape of
pack should be chosen on the basis of area being treated. The common sizes are small (for
smaller joints like elbow, ankle), large (for large joints like hip and back), contoured (for
cervical spine).
The common effects produced are increased in local circulation, relief of spasm, relieve
of pain and increase in joint range of motion.
Contraindications are impaired skin sensation, open wounds, recent hemorrhage, skin
allergy and impaired circulation.
WHIRLPOOL BATH
The use of water for therapeutic purposes is taking place since ancient times. The use of
whirlpool bath has becoming an increasingly valuable means of physiotherapeutic treatment.
The principle of whirlpool bath therapy is to combine the effects of temperature with the
mechanical effects of the water. Warm whirlpool contains water at temperature ranges
between 3645C and a jet of water or air stream is allowed to produce turbulence in the water.
This turbulence can also be produced by electric motor incorporated into the apparatus.
Depending upon the size of the apparatus, whirlpool bath can be used for the treatment
of limbs or extremities (upper or lower) or the whole body (Fig. 7.4). Part is immersed
into the water and jet of stream is allowed

to produce turbulence in the hot water.
Treatment is usually given for 1520
minutes depending upon the area or
condition of the patient.
Whirlpool baths can be used for various
rheumatic disorders, postimmobilization
stiffness, joints pain, etc. The warm whirl-
pool is an excellent post surgical modality
to increase systemic blood flow, removing
waste products and thus reduces pain. It
is effectively used in sports medicine for
relaxation after practice or competition
and for the treatment of various injuries.
To maintain proper hygiene, whirl-
pool baths need to be cleaned frequently.
Some disinfectant or antimicrobial agent
should be used for cleaning the tank,
turbine and jet or nozzle.
Contraindications are open wounds, Fig. 7.4: The whirlpool bath
recent hemorrhage, skin allergy, eczema
or infection.
CONTRAST BATH
The principle of contrast bath therapy is to combine the effects of both hot as well as cold
bath together. The part is immersed alternatively in hot and in cold water tanks (Fig. 7.5).
The temperature of hot water ranges from 3645C and the cold water from 1520C. The
part is immersed first in the hot water and then in the cold water, and the treatment is
repeated thereafter. As a general rule, the treatment should begin with the hot water and
should end with the cold water.
Fig. 7.5: Contrast bath

The total treatment time may vary between 1530 minutes, with immersion in the
warm around 3 minutes and in cold around 1 minute. The whole cycle is repeated for
about 45 times.
Effects: The alteration in warm and cold leads to vasodilatation and vasoconstriction
at regular intervals. It leads to reduction in edema and is beneficial in various chronic
peripheral circulatory disturbances.
The regular change in temperature also leads to considerable change in the sensory
stimulus. This stimulus is relatively vigorous because each time neural stimulation starts to
occur the temperature stimulus is reversed. This strong sensory stimulus acts to suppress
pain by means of gate mechanism and accounts for suppression of pain in many patients
receiving this treatment.
To maintain proper hygiene, contrast baths are also need to be cleaned frequently.
Some disinfectant or antimicrobial agent should be used for cleaning both the tanks.
Contraindications are open wounds, recent hemorrhage, skin allergy, eczema or
infection.
HELIOTHERAPY
Helio means sun and therapy means treatment. The use of natural sunlight for therapeutic
purposes is better known as heliotherapy. The use of sunlight is prevalent since the times
of ancient Greeks and Romans. In modern days, persons can be seen taking sunbaths at the
beaches in the coastal regions.
Heliotherapy is effective in the treatment of psoriasis and other skin conditions as the
sunrays emit ultraviolet radiations.
SAUNA BATH
The use of sauna bath was started from Finland. Its first use came into picture in 1936
in Berlin during the period of Olympic games. Many players saw Scandinavians using
this bath. Its use at a very large scale comes into picture in 1972 during Munich Olympic
Games where a large number of sauna bath chambers were made available to the athletes
by which it becomes popular worldwide.
Sauna bath is administered in a wooden chamber. One hot oven is used inside the
sauna chamber. Stones are placed on the oven and allowed to heat. Water is poured to
produce some steam in short bursts. Wooden chamber is used for sauna bath because it
absorbs humidity from the inside air and thus restores dryness in the chamber. Regular
monitoring of temperature and humidity is done with thermometer and hygrometer.
Sauna is a dry hot air bath. The temperature is kept between 6090C and relative humidity
of the air is maintained between 510%. One treatment session is about 30-40 minutes and
consists of two phases: The sweating phase and the cooling phase.
Phases of Sauna Bath

The sweating phase: Intense sweating occurs in the sauna bath chamber. About 5001000
gram of water is usually lost in one session. The aim is to open all the pores in the skin.
Patient is allowed to sit on the lower benches to start and only gradually move up to the
higher ones. Loss of weight is seen due to the loss of water from the body. It can be very
quickly regained by a corresponding intake of fluids along with minerals.
The cooling phase: The sweating phase is followed by a cooling phase, which is an important
part of the sauna. To begin cooling with cool air, then take a cold shower and then finally to
take a dip into a cool pool of water. The aim is to close all the opened pores after removing
waste products along with the sweat. Cooling should always begin from the feet and then
moving upwards.
The sauna bath chamber is reentered after a pause of 1015 minutes. After two or three
sessions of sauna, a rest period of at least 30 minutes is absolutely necessary.
Mineral water, herb tea or fruit juice to provide adequate hydration is also necessary
after sauna bath. Light food involving lots of salad, fruit, yoghurt, etc. should be given
only after half an hour.
Physiological effects: The physiological effects of sauna bath include increase of general
circulation. It provides lots of fresh blood to the tissues. It helps removing waste products
of metabolism from the body. It relaxes the body and gives a sense of general well-being.
Pain is also relieved substantially from the body.
Sauna baths are now a days used in weight reduction programs. Making weight
(reducing or increasing weight) by athletes taking part in competition is not advisable.
8 Ultrasonic Therapy
In the medical community, ultrasound is the modality that is used for a number of purposes
including diagnosis, destruction of tissues and therapy. Diagnostic ultrasound is used for
imaging the fetus during pregnancy. Destructive ultrasound is used to produce extreme
tissue hyperthermia which has been demonstrated to have tumoricidal effects in cancer
patients.
Therapeutic ultrasound is most widely used modalities in physiotherapy department
(Fig. 8.1). It has been used as a valuable tool in rehabilitation of many different injuries,
to stimulate the repair of soft tissue injuries and to relieve pain. It has been traditionally
classified as a deep heating modality and used primarily to elevate tissue temperature.
Ultrasound is not strictly electrotherapy because it is a mechanical vibration, albeit
(although) produced electrically. It has sometimes been described as micro-massage.
The meaning of ultra is beyond or extreme. Sound is defined as the periodic mechanical
disturbance of an elastic medium such as air.
Ultrasound refers to mechanical vibrations which are essentially the same as sound waves but of
a higher frequency. Such waves are beyond the range of human hearing and therefore also be called
ultrasonic.
Fig. 8.1: Therapeutic ultrasound

Frequency of Ultrasound: Ultrasonic energy or ultrasound describes any vibration at

a frequency above the audible sound range, i.e. 2020000 Hz but it is frequencies of a
few megahertz that are typically used in physiotherapy: Several different therapies are
employed in range from 0.5 to 5 MHz. Majority of ultrasound generators are set at a
frequency of 1 MHz, although there are ultrasound units that are set at a frequency of 3
MHz (Fig. 8.2). A generator that can be set between 1 and 3 MHz affords the therapist the
treatment flexibility.
Fig. 8.2: Ultrasound treatment heads
Ultrasonic energy generated at 1 MHz is

transmitted through the more superficial tissue
and absorbed primarily in the deeper tissues at
depths of 3 to 5 cm.
A 1 MHz frequency is most useful in individ-
uals with a high percentage of cutaneous body fat
and whenever the desired effects are in the deeper
structures. At 3 MHz, the energy is absorbed in Fig. 8.3: Depth of penetration of
the more superficial tissues with a depth of pene- ultrasound waves
tration between 1 and 2 cm (Fig. 8.3).
Properties of Waves
Sonic waves are a series of mechanical compression and rarefactions in the direction of
travel of the wave, hence they are called longitudinal waves (Fig. 8.4).
They can occur in solids, liquids and gases and are due to regular compression and
separation of molecules. The passage of these waves of compression through matter is,
Ultrasonic Therapy 247
Fig. 8.4: Compression and rarefaction
of course, invisible because it is the molecules that vibrate about their average position as
a result of the sonic wave (Fig. 8.5).
Fig. 8.5: Effect of a change of potential applied to the crystal and the
effect of this on adjacent cells
As sound waves pass through any material, their energy is dissipated or attenuated.
Sometimes all the energy is absorbed at once. Sometimes the sound wave passes with
almost no loss. The molecules of all matter are in constant random motion; the amount of
molecular agitation is, what is measured as heat. The greater the motion is oscillatory, for
instance the whole molecule may move or rotate to and fro, or it may change shape in an
oscillatory way and this may occur at many different frequencies.
The velocity of a wave is the speed at which the wave moves through the medium, and
it varies depending upon the physical nature of the medium. Sound waves will pass more
rapidly through material in which the molecules are closed together, thus their velocity is
higher in solids and liquids than in gases. The velocities of sound in some media are:
Air 344 m/s
Water 1410 m/s
Muscle 1540 m/s
Bone 3500 m/s
Production of Ultrasound: Ultrasound can be produced by following ways:

For 1 MHz machine a vibrating source with a frequency of one million cycles per second
is needed. This is achieved by using either a quartz or a barium titanate or a lead zirconate
or nickel-cobalt ferrite crystal. These crystals deform when subjected to a varying potential
difference, this is called piezoelectric effect.
The basic components of ultrasonic apparatus are shown in Figure 8.6.
Fig. 8.6: The components of ultrasonic apparatus
There is a source of high frequency current,

which is conveyed by a coaxial cable to a trans-
ducer circuit or treatment head or applicator or
sound head. Inside the transducer circuit high
frequency current is applied to the crystal being
fused to the metal front plate of the treatment
head. Any change in the shape of the crystal
cause a movement of the metal front plate which
Fig. 8.7: Passing of ultrasonic waves
in turn produces ultrasonic waves.
in different medium
Strict frequency control of high frequency
current (1 MHz or 3 MHz) ensures a steady and
regular rate of deformation (to put out of shape).
Figure 8.5 shows the effects of a change of potential applied to the crystal and the effect
this has on adjacent cells. Ultrasonic waves are propagated in a linear fashion up to the end of
the near field at which point the beam starts to diverge (Fig.8.7).
Transmission of Ultrasound
If ultrasonic beam encounters an interface between two media and is transmitted, it may
be refracted, i.e. deflected from its original path as light. When traveling from a medium
in which its velocity is low into one in which its velocity is high, it is refracted away from
the normal.
The significance of refraction is that in Figure 8.7 if T were the target, refraction would
cause the ultrasonic beam to miss it. As refraction does not occur when the incident waves
travel along the normal, treatment should be given with the majority of waves traveling
along the normal (i.e. perpendicular to the interface between the media) whenever possible.
Attenuation of Ultrasound
It is the term used to describe the gradual reduction in intensity of the ultrasonic beam once
it has left the treatment head. There are two main factors that contribute to attenuation.
Absorption
Ultrasound is absorbed by the tissues and converted to heat at that point. This contributes
the thermal effect of ultrasound.
Scatter (to spread)

This occurs when the normally cylindrical ultrasonic beam is deflected from its path by
reflection at interfaces, bubbles or particles in its path.
The overall effect of these two is such that the ultrasonic beam is reduced in intensity
the deeper it passes. This gives rise to the expression half-value distance which is depth
of soft tissue that reduces the ultrasound beam to half its surface intensity.
The half value distance for soft tissue varies for 1 MHz and 3 MHz output and is 4 and
2 cm respectively. In practical terms when treating deeper structures consideration needs
to be given to the frequency and intensity of ultrasound chosen.
Ultrasonic Fields
A further consideration relating to depth of penetration and intensity of ultrasonic beam in
the division of the beam into a near and a far field (Figs 8.8A to C).
Figs 8.8A to C: Ultrasonic fields

The extent of the near field depends upon the radius (r) of the transducer and the
wavelength () of the ultrasound in the medium. The depth of the near field can be calculated
using the formula r2/. As wavelength and frequency are inversely related, the depth of the
near field varies with the frequency of ultrasound.
The near and far fields arise because the wavefronts from different parts of the source
have to travel different distances, and consequently there is interference between adjacent
fronts. At some points the interference to constructive and the waves combine their energy,
and thus when viewed in both longitudinal and transverse profile there will be points in
the ultrasonic beam where intensity is high and points where intensity is low. This is most
marked in the near field where there are considerable changes in pressure.
The extent of the near field is of significance in that it is more intense than the far field
and may have a more profound effect in the treatment of certain conditions. However, the
near field has a much greater variation in intensity than the far field. Consequently, the
frequency of the ultrasound and the radius of the transducer may need to be considered
when treating tissue at a depth greater than 6.5 cm.
Coupling Media
Ultrasonic waves are not transmitted by air, thus some couplant which does transmit
them must be interposed between the treatment head (transducer) and the patients
skin.
Unfortunately, no couplant affords perfect transmission and only a percentage of the
original intensity is transmitted to the patient. Even most efficient couplant reduces the
applied dose by a quarter.
Air (zero transmission) will infact reflect the ultrasound beam back into the treatment
head and this could set-up standing wave which might damage the crystal. Consequently,
the treatment head is never left switched on when not in contact with a transmitting
medium.
Some coupling medias and their efficiency of transmission are:
1. Aquasonic gel 72.6%
2. Glycerol 67%
3. Distilled water 59%
4. Liquid paraffin 19%
5. Petroleum jelly 0%
6. Air 0%
Characteristics of a Coupling Media

1. An acoustic impedance similar to the tissue
2. High transmissivity for ultrasound
3. High viscosity
4. Low suspectibility to bubble formation
5. A chemically inactive nature
6. A hypoallergic character
7. Relative sterility
8. Cheap
9. Couplant should also act as a lubricant to allow the treatment head to move smoothly
over the skin.
Treatment Parameters
Ultrasound may be used in a continuous mode or in pulsed mode.
In continuous mode, treatment head continuously produces ultrasonic energy. In
pulsed mode, the periods of ultrasound are separated by periods of silence.
Intensity
In ultrasound intensity unit is Watt but this is a gross measure of the power being emitted
by the treatment head, so an averaged intensity is normally used.
1. Space averaged intensity: where the average intensity over a specified area is given,
e.g. Watts per square cm (Wcm2).
2. Time averaged/space averaged intensity can be used when the ultrasound is being
applied in a pulsed mode, and gives the average intensity over the whole treatment time
(per second) for a specified area (Wcm2). For example, if 0.5 Wcm2 is applied pulsed
1 : 4, then in one second the average intensity (as if the ultrasound were continuous)
would be 0.1 Wcm2. The output meters on some ultrasound generators automatically
make this adjustment when using pulsed ultrasound.
Pulsed Mark: Space Ratio

When ultrasound is applied in its pulsed mode, the ratio of the time on to time off should
be expressed. This is the mark: space ratio, the mark being the time ultrasound on, space
being the silence, both being measured in milliseconds. Some units have a single fixed
M : S ratio of 2 : 8, whereas others have a variable range, e.g. 1 : 1, 1 : 4, 1 : 7.
Reflection of Ultrasound
Sound obeys the law of reflection and if an ultrasonic beam traveling through one
medium encounters another medium which will not transmit (let it pass into the
new medium), reflection takes place. Air will not transmit ultrasonic waves, so in
ultrasonic treatment great care is taken to avoid leaving air between the treatment
head and the patient to minimize reflection. However, there will always be some
reflection at each interface that the ultrasound beam encounters. This gives rise to the
term acoustic impedance (Z) which is the ratio between the reflected and transmitted
ultrasound at an interface. When the acoustic impedance is low, transmission is high
and vice versa.
Testing the Apparatus

Prior to any treatment it is sensible to check that there is an output from the machine.
This can be done by placing the treatment head just below the water surface in a suitable
container and observing the disturbance (ripples) which appears (Fig. 8.9).
Fig. 8.9: Testing the apparatus
The apparatus should be on and off with the treatment head below the water. This, and
similar methods, only indicate the presence of an output but to quantity it, a radiation.
Balance should be used regularly.
Techniques and methods of application

Preparation of Patient
Skin should be washed and hairs should be removed. The nature of the treatment, need
for a couplant and stability of the area are all needs to be explained to the patient. The
duration of the treatment as well as any particular cooperation required is indicated.
Examination and Testing

Skin surface to be treated should be inspected; inflammatory skin conditions should be avoided.
Preparation of the Part to be Relaxed

The couplant should be applied to the skin surface.
Setting Up
The patient should be in a comfortable position as skill is needed to apply efficient ultrasound
therapy, ensuring close contact, appropriate movement and correct angle of the transducer
at all times.
The treatment head is placed on the skin before the output is turned on. This is to
avoid damage to the transducer which can occur if the energy is reflected back into the
transducer. Some machines have a monitoring system. If the ultrasound energy reaching
the tissues becomes much less than the set intensity, the output is greatly reduced, the
timer stops and the operation is alerted in some way.
Instructions and Warnings

The patient is asked to keep the part still and relaxed and to report if any increase of pain
or other sensations immediately.
Application
The treatment head is moved continuously over the surface while even pressure is
maintained in order to iron out irregularities in the sonic field. The emitting surface must
be kept parallel to the skin surface to reduce reflection and pressed sufficiently firmly to
exclude any air. The rate of movement must be slow enough to allow the tissues to deform
and thus remain in complete contact with rigid treatment head but fast enough to prevent
hot spots developing when using a high intensity treatment. The pattern of movement
can be a series of overlapping parallel strokes, circles or figures of eight (Fig.8.10).
Fig. 8.10: Methods of application
Termination
The intensity is returned to zero, either manually or automatically before the transducer is
removed from the water bath or tissue contact. The skin is cleaned of couplant or dried. The
transducer should be cleaned after each use with a noncorrosive, nonabrasive antiseptic lotion.
Recording
The following should be recorded:
1. Machine used
2. Intensity
3. Frequency
4. Pulse mode
5. Insonation time
6. Couplant
7. Region and area of insonation
8. Response of treatment.
Direct contact Method
If the surface to be treated is fairly regular then a
coupling medium is applied to the skin in order to
eliminate air between the skin and the treatment head
and transmit the ultrasonic beam from the treatment
head to the tissues. The treatment head is moved in Fig. 8.11: Direct contact method
small concentric circles over the skin in order to avoid
concentration at any one point, keeping the whole of
the front plate in contact with the patient. This technique is suitable for areas up to three
times the size of the treatment head. Large area should be divided and each area treated
separately. The size of the area and its exact location should be specified on the treatment
head (Fig. 8.11).
Water Bath Method

When direct contact is not possible because of irregular shape of part or because of
tenderness, a water bath may be used. As the part to be treated is immersed in water this
can only reasonably be applied to the hand, ankle and foot.
A water bath filled with degassed water is used if possible. Ordinary tap water presents
the problem that gas bubbles dissociate out from the water, accumulate on the patient skin
and the treatment head, and reflect the US beam. If tap water has to be used then the gas
bubbles must be wiped from these surfaces frequently.
The patient is seated and part is put in water of
a comfortable temperature in such a position that it
is suitably supported (Fig. 8.12).
The treatment head is placed in the water
and held 1 cm from the skin and moved in small
concentric circles, keeping the front parallel to the
skin surface to reduce reflection to a minimum.
If the patients hand is to be immersed in the
bath while the application is active, care should
be taken to minimize exposure to any reflected or Fig. 8.12: Water bath method
scattered ultrasound. This can be done by wearing
a dry knitted glove inside a water-proof rubber or
plastic glove.
Water bag method

Another method of applying ultrasound therapy to irregular surface which cannot
conventionally be placed in a water bath is treated with a plastic or rubber bag filled with
water forming a water cushion between the treatment head and the skin.
Rubber bag filled with degassed water can be used. All visible air bubbles should be
squeezed out before knotting the neck of the bag to seal it. A coupling medium has to be
placed both between the rubber bag and skin and between the rubber bag and the treatment
head to eliminate any air (Fig. 8.13).
Fig. 8.13: Water bag method
The bag placed on irregular surface is then held with the help of patient or others.
Treatment head pressed firmly on to the bag so that a layer of water about 1 cm thick
separates it from the surface (body). Inevitably, some bubbles will form and it is important
to ensure that these are in the sides of the bag and not in the region transmitting the
ultrasound. The treatment head is then moved over the surface of the bag. It does, however
present problems in terms of attenuation as many more interfaces have to be crossed by
the ultrasound and rubber absorbs much of ultrasonic energy. To minimize the problem,
condoms or thin balloons are more satisfactory because these are thin, cheap and easy to
use.
Dosage
Three factors which determine ultrasound dosage are as follows:
1. size of the treatment area
2. depth of the lesion from the surface
3. nature of lesion.
Parameters of Ultrasound
1. Mode
2. Frequency
3. Intensity
4. Duration of treatment.
When treating the patients with ultrasound it is worth remembering that the intensity
of ultrasound leaving the treatment head is not the intensity being applied to the deep
tissues. Intensity therefore has been reduced by:
i. absorption in the coupling medium
ii. attenuation of the beam by absorption and scatter
iii. refraction of the beam at tissue interfaces which may deflect the beam always from the
offending tissue.
Mode
Continuous mode produces more heat so it is used for musculoskeletal conditions such as
muscular spasm, joint stiffness, pain, etc.
Pulsed mode produces less heat so it is used for soft tissue repair, e.g. tendinitis.
For example, 0.5 W/cm2 pulsed at 1 : 4 deliver the same energy as 0.1 W/cm2 on a
continuous mode.
Frequency
Attenuation increases with increase in frequency effectively lower frequency penetrate
further.
1. Ultrasonic 3 MHzsuperficial tissue
2. Ultrasonic 0.75 to 1 MHzpenetrate deeply.
Intensity
Power is the total energy/sec supplied by the machine and is measured in watts.
Intensity applied is according to the nature of the lesion.
For acute and immediate post-traumatic: 0.1 to 0.25 W/cm2
For chronic and scar tissue: 0.25 to 1 W/cm2.
Duration of Treatment
Amount of energy depends on intensity and duration of treatment.
Size of area determine the treatment time
12 minutes for every cm2
Many transducer heads have an area of 5 cm2 and the palm of the small hand is about
50 cm2.
Minimum 12 minutes
Maximum 8 minutes
Average 5 minutes
For chronic Longer treatment time
For acute Lesser treatment time
Dosage in Acute Lesion or Conditions

In any acute conditions treatment applied cautiously to prevent exacerbation of symptoms.
1. Initial stage
Low dose
0.25 to 0.5 Wcm2
Time 23 minutes
Progression unnecessary if condition improves
2. Failure case
0.25 to 0.5 Wcm2
Time 45 minutes
Or
0.8 Wcm2
Time 23 minutes.
Aggravation of symptoms is not always a bad sign as it may indicate repair processes
are taking place. During that situation a reduction in dose in both time and intensity may
be indicated (or) treatment with ultrasound may be deferred (to postpone or to put off)
until symptoms subsides to their original level. It may also possible to select different M :
S pulse ratio and use:
1 : 7 for very acute
1 : 1 for less acute.
Dosage in Chronic Condition

Chronic condition may be treated with pulsed or continuous mode. The maximum intensity
of ultrasound which should be used is that which produces mildly perceptible warmth.
This usually occurs around 2 W/cm2. Initially low dose is tried. Intensity 0.8 W/cm2, time:
4 minutes
If improvement occurs treatment is repeated. If no improvement occurs, dose is gradually
increased.
Maximum dose of ultrasound: 2 Watts/cm2 for 8 minutes.
If no improvement occurs after 6 sittings, ultrasound treatment has to be discontinued.
Progression and timings: Frequency of treatment.
Recent injuries and acute conditions: once or twice daily.
Chronic conditions: Every alternate day.
Physiological Effects of Ultrasound

Following ultrasonic therapy the physiological changes that take place are as follows:
Thermal Effects
As the ultrasound waves are absorbed by the tissues they are converted into heat. The
amount of heat developed depends upon:
1. Absorption of the tissues, e.g. protein absorbs ultrasound more effectively and therefore
produces much heat.
2. The number of times the treatment head passes over the part.
3. The efficiency of circulation through the insonated tissues.
4. When using continuous ultrasound, the amount of heat developed is directly propor-
tional to the intensity and duration of insonation.
5. When using pulsed ultrasound there is less thermal effect than with continuous and a
mark : space ratio 1 : 4 produces less heat than 1 : 1.
6. Reflection of ultrasound at a tissue interface produces a concentration of heating effect at
a specific point (Fig. 8.14). This is particularly likely at the interface between periosteum
and bone. As reflection from bone occurs there is double intensity of ultrasound in
the periosteal region, which may cause localized over heating and can manifest itself
as periosteal pain. In practical terms this means that it is best to avoid passing the
ultrasound treatment head over the subcutaneous bony points if possible.
Fig. 8.14: Reflection of US beam from bone, concentration of

heating effect may leads to periosteal pain
Uses of Thermal Effects

The local rise in temperature could be used to accelerate healing. The extensibility of
collagen is increased by rise in temperature and so stretching of scars or adhesions is easier
following ultrasound. The thermal effect may also help reducing pain.
In the past ultrasound was classified as a heat treatment, but recent work has shown
that there are many nonthermal effects of ultrasound which may be of use in treatment.
These effects are all associated with one another, and arise because of considerable
force generated within the tissues by the ultrasound. The nonthermal effects are as
follows:
Cavitation
This is the oscillatory activity of highly compressible bodies within the tissues such as gas
or vapor filled voids (Fig. 8.15).
Cavitation may be stable or unstable cavitation.
Fig. 8.15: Cavitation: Compression and contraction of air bubble

due to ultrasonically induced pressure
Stable cavitation: Stable cavitation occurs when bubbles

oscillate to and fro within the ultrasonic pressure waves
but remain intact. It is not dangerous and could be of
benefit as it modifies the ultrasonic beam in such a way as
to cause microstreaming.
Microstreaming is the unidirectional movement of fluids
along the boundaries of the cell. Due to microstreaming,
permeability of cell membrane and direction of movement
of molecules into the cells is influenced (Fig. 8.16).
Unstable or Transient Cavitation: This occurs when the
volume of the bubbles changes rapidly and then collapse.
It is potentially dangerous to the tissues as the collapse
of the bubbles cause a great local rise in temperature. Fig. 8.16: Microstreaming
It is avoided by moving the treatment head (to prevent
standing waves) using a low intensity (below 3 watt/cm2) and using a high frequency
(1 or 3MHz).
Mechanical Effect or Micromassage

This occurs where the longitudinal compression waves of the ultrasound beam produces
compression and rarefaction of cells, and affect the movement of tissue fluid in interstitial
spaces. This can help in reducing edema. Combined with the thermal effect the extensibility
of scars and adhesions could be affected in such a way to make stretching them easier. It is
also possible that the mechanical effect could help reduce pain.
Biological Effect
Ultrasound can have some useful effects in all three stages of repair.
1. Inflammatory: Ultrasound probably increases the fragility of lysosome membrane,
and thus enhances the release of their contained enzymes. These enzymes will help to
clear the area of debris and allow the next stage to occur.
2. Proliferative: Fibroblasts and myofibroblasts may have Ca++ ions driven into them by
the ultrasound. This increases their mobility and encourages their movement toward
the area of repair. The fibroblasts are stimulated to produce the collagen fibers to form
scar and myofibroblasts contract to pull the edges together.
3. Remodeling: Ultrasound has been shown to increase the tensile strength of the scar by
affecting the direction, strength and elasticity of fibers which make up the scar easier.
Therapeutic uses of ultrasound

1. Uses of ultrasound: Ultrasound is often used after soft tissue injuries as the mechanical
effects help to remove the traumatic exudates and reduces the danger of adhesion
formation. Heat produced by ultrasound in large diameter nerve fibers may reduce
pain through gate mechanism. Accelerated protein synthesis stimulates the rate of
repair of damaged tissues.
2. Scar tissue: Scar tissue is made pliable (capable of bend or twist) by the application
of ultrasound, which allows more effective stretching of contracted scars. If the scar is
bound down on underlined structures ultrasound may help in gaining its release.
3. Chronic indurated edema: The mechanical effects of ultrasound have an effect on
chronic edema and helps in its treatment. It also breaks down adhesions formed
between adjacent structures.
4. Varicose ulcers: Ultrasound is found effective to promote the healing of varicose
ulcers and pressure sores.
5. Blood flow: In an investigation of the effect of continuous ultrasound on blood flow,
a dose of 1.5 W/cm2 for 5 minutes applied to the forearm did not alter the skeletal
muscle blood flow.
6. Bone injuries: Ultrasound in the first and second week after bony injury can
increase bone union, but given to an unstable fracture during the phase of cartilage
proliferation, it may result in proliferation of cartilage and therefore decrease in bone
reunion. Ultrasound can also be used in early diagnosis of stress fractures. A moderate
dose applied over the site of the fracture leads to intense pain, whereas the same dose
applied to the opposite side has no pain. Thus, ultrasound can identify stress fractures.
7. Plantar warts: Plantar warts are occasionally seen in the athletic population, occurring
on the weight bearing areas of the feet and caused by either a virus or microtrauma.
These lesions contain thrombosed capillaries in a whitish colored soft core covered by
hyperkeratotic epithelial tissue. Among other more conventional techniques, several
studies have recommended as an effective painless method for eliminating plantar warts.
8. Placebo effect: While the physiological effects of ultrasound have been discussed
in detail, it can also have significant therapeutic psychological effects. A number of
studies have demonstrated a placebo effect in patients receiving ultrasound.
Dangers of ultrasound
1. Burns: If continuous beam is used and is allowed to remain stationary, excess heat can
accumulate in the tissues and eventually leads to burns. However, the danger of burn
is effectively eliminated by keeping the treatment head moving, using pulsed beams
and avoiding bony prominence if possible.
2. Cavitation: Especially unstable cavitation is dangerous and has been described
previously.
3. Overdose: Excessive dose may cause an exacerbation of symptoms.
4. Danger to equipment: If the treatment head is held in the air while switched on, the
reflection of the beam back into the treatment head may set-up standing waves which
could damage the crystal, consequently the head is never turned on unless it is contact
with the transmitting material.
Contraindications
1. Vascular conditions: Conditions such as thrombophlebitis, where insonation may
cause emboli to be broken off, are not treated with ultrasound.
2. Acute sepsis: An area which presents acute sepsis should be treated cautiously with
ultrasound because of the danger of spreading the infection, or in some instances
breaking off septic emboli. If the treatment is passed over an infected area (as in the
treatment of herpes zoster) it must be sterilized with an appropriate solution before
treatment of the next patient.
3. Radiotherapy: Radiotherapy has a devitalizing effect on the tissue, therefore ultrasound
is not applied to a radiated area after six months of irradiation.
4. Tumors: Tumors are not insonated because they may be stimulated or metastasize.
5. Pregnancy: A pregnant uterus is not treated as the insonation may cause damage
to the fetus. Consequently during pregnancy the back and abdomen should not be
treated.
6. Cardiac disease: Patients who have had cardiac disease are treated with low
intensities in order to avoid sudden pain, and area such as cervical ganglion and the
vagus nerve are avoided because of the risk of cardiac stimulation. Patients fitted
with cardiac pacemakers are not usually treated with ultrasound in the area of the
chest, as the ultrasound generator may have an effect on the pacemakers rate of
stimulation.
7. Hemorrhage: When bleeding is still occurring or has only recently been controlled, such
as an enlarging hemarthrosis or hematoma or uncontrolled hemophilia, ultrasound is
contraindicated.
8. Severely ischemic tissue: Because of the poor heat transfer and possibly greater
risk of arterial thrombosis due to statistics and endothelial damage, ultrasound is
contraindicated.
9. Nervous system: Normal doses of ultrasound have been applied for many years to
the tissues around the spinal cord without any ill effects. Infact treatment of the spinal
nerve roots and over the apophyseal joints is particularly common. Since the CNS is
deeply buried beneath the thick muscles and more importantly bone tissue, it seems
reasonable to suppose that only trivial amounts of energy could reach it. Where the
nerve tissue is exposed, e.g. over a spina bifida or after laminectomy, ultrasound is
avoided.
10. Specialized tissue: The fluid filled eye offer a exceptionally good ultrasound transmission
and retinal damage could occur. Treatment over the gonads, i.e. testes and ovary are also
not recommended.
11. Implants: Although metal implants in the tissue would reflect the ultrasound at their
interfaces and thus leads to more energy absorption in this area, this does not lead to
a large temperature rise in the region because the amount of heat generated is easily
conducted collar areas. The effect might, however, be different with smaller and more
superficial implants like metal bone fixing pins subcutaneously placed; as a precaution
low doses are used in these areas.
Plastics used in replacement surgery as high intensity polyethylene and acrylic
should also be avoided since their effect on ultrasound absorption is unknown.
12. Anesthetic area: If ultrasonic is given to anesthetic area, there will not be any type of
pain or heat experienced by the patient which could lead to burns.
Phonophoresis
Phono means sound and phoresis means migration of the ions through a membrane by the action
of an electric current.
Phonophoresis is defined as the movement of the drugs through skin into the subcutaneous tissues
under the influence of ultrasound. It is otherwise called as sonophoresis or ultrasonophoresis.
Principle
Phonophoresis relies on perturbation of the tissue causing more rapid particle movement
and thus encouraging absorption of the drug.
Effects of Phonophoresis
The thermal effects of ultrasonic increase tissue permeability and the acoustic pressure created
by the ultrasonic beam drives the medication into the tissues. Thus, the medication follows
the path of beam. Both pulsed and continuous ultrasonic have been used in phonophoresis.
Continuous ultrasonic at an intensity great enough to produce thermal effects may induce
a proinflammatory response. If the goal is to decrease inflammation, pulsed ultrasonic with
low spatial-averaged temporal peak intensity may be the best choice.
Penetration of Phonophoretically Driven Drugs

The depth to which drugs can be made to penetrate is a matter of particular uncertainty.
Once the drug has passed through the epidermis, it is likely to be dispersed in the circulation
to an extent which depends on the vascularity of the tissues concerned and the ease with
which molecules of the drugs can enter blood vessels. Ultrasonic machine with 0.33 or
0.25 MHz were found to be more effective. Low frequency leads to greater penetration. It
must be realized that deeper penetration does not necessarily infer greater effectiveness. If
therapeutic effects occur in the dermis and epidermis, such as cutaneous anesthetic effect
of lignocaine, it might be expected that higher frequencies would be of a more effective,
since the ultrasonic energy is largely absorbed in the superficial tissues. This has been
shown to occur in that 1.5 and 3 MHz ultrasonic appeared to be more effective in achieving
absorption of local anesthetic than 0.75 MHz. Interestingly, this same study showed that
pulsed was rather more effective than continuous ultrasonic in achieving transfer of this
particular analgesic. This provides evidence for a specific effect due to the energy of
ultrasonic.
Drug used in Phonophoresis

The anti-inflammatory drug hydrocortisone has been widely used. High concentration of
the drug 10% ointments are more effective when comparing 1% can be driven through the
skin with relatively high intensity ultrasonic. Many inflammatory skin conditions have
been treated with hydrocortisone.
It is possible that ultrasonic therapy having a proinflammatory and steroid an anti-
inflammatory are conflicting therapies.
Other steroid-type drugs can be applied by phonophoresis as well as many non-steroidal

anti-inflammatory drugs mainly salicylates. An anti-inflammatory analgesic cream
(trolamine salicylate) has been recommended. A study to investigate the effectiveness of this
agent on delayed onset muscle soreness (DOMS) in normal subjects found that ultrasound
alone increases the symptom while ultrasound with trolamine salicylate has no such effect.
It was concluded that the anti-inflammatory activity of this drug was able to offset the
increased soreness due to the proinflammatory effect of ultrasound.
Phonophoresis of hydrocortisone has been used in the reactions of many skin conditions
including psoriasis, scleroderma, bursitis.
A lotion containing zinc oxide, tannic acid, urea and menthol has been applied by
phonophoresis to treat herpes simplex virus type II in both oral and genital infections with
good results.
Antibiotics such as penicillin have been given by phonophoresis for the treatment of
skin infections.
Applications
The drug to be driven into the tissue is combined in a suitable gel or cream which forms
the couplant. It is smeared onto the part using a spatula (an instrument with broad blade
for spreading pigments) so that it is not applied by the patient fingers.
Treatment head is used onto the skin in a usual manner. Relatively high intensities of 1
and 1.5 W/cm2 have been used.
The depth of the target tissue determines the frequency used.
The time of treatment depends on the area over which phonophoresis is to be applied.
1 minute treatment for every 10 cm2 area is reasonable, although some suggest 5 minutes
for each 25 cm2, i.e. about 1 minute for 30 cm2.
After the completion of treatment, the drug should be removed from both the patients
skin and the transducer head. Because of unnoticeably applied to other patient with same
treatment head.
Since the cream or gel containing the drug is being used as the coolant, it is important
that it transmits ultrasonic adequately. In general that gels are more efficient coupling agents
than creams particularly for higher frequency ultrasonic (1.5 and 3 MHz).
Contraindications
The same considerations apply when giving phonophoresis as apply when giving
ultrasonic for its intrinsic effects.
The effect of the drug must also be considered; for example, anti-inflammatory drugs
may suppress necessary inflammatory reaction, such as local skin infections, allowing
them to become more serious.
If local skin anesthetizing drugs are being driven in by ultrasonic waves, it must be
remembered that skin sensation under the treatment head will gradually be lost so that the
patient may no longer detect excessive heat: high intensities should not therefore be used
for these drugs.
Keep in mind that allergies and sensitivities to the substance contraindicate its use on
the skin as well for example:
1. Patient who cannot eat sea food should not be treated with iodine. If skin irritation
and itching occurs, it should be reported. The usual antidote is an antihistamine. An
alternative should be selected in future treatment.
2. Patient sensitive to metals should not be treated with zinc. These patients usually
cannot wear metallic watch bands, jewellery, etc. without having skin reaction and
at times, systemic reactions. Dermatologic consultation should be sought for specific
antidotes for offending metals. Nonmetallic substances should be substituted.
3. If a patient has a reaction to mecholyl with vasomotor shifting, administer a simple
stimulant such as black coffee. Vertigo form orthostatic adjustment is usually momentary.
4. Reactions to hydrocortisone are not as common as you think. The culprits are usually
the chemicals included in the base of ointment or solution (e.g. novocaine) rather than
the steroid itself. Have the patient use an antihistamine skin lotion should any dermal
irritation occur.
5. Do not treat a patient with salicylates if he or she is sensitive to aspirin. Seek medical
consultation for the specific treatment of symptoms. It should be noted that although
the above reactions are extremely rare, the efforts taken in the prevention of their
occurrence will be well worthwhile.
Combination therapy
The application of two therapeutic modalities at the same time, and at the same site
is described as combination therapy. Ultrasonic therapy is frequently used with other
modalities including hot packs, cold packs and electric nerve and muscle stimulating
currents.
The most widely used combinations are those of ultrasonic with some form of nerve
and muscle stimulating current for example, ultrasonic and interferential. This can be done
because the ultrasonic transducer provides low resistance electrical contact with skin.
Electrical stimulating currents are used for analgesia or producing muscle contraction.
Ultrasonic and electrical stimulating currents have been recommended to treat myofascial
trigger points. Both modalities provides analgesic effects and both are effective in reducing
the pain-spasm-pain cycle.
Hot packs and high intensity ultrasonic are used primarily for their thermal effects.
Heat is effective in reducing muscle spasm and muscle guarding. It also has an analgesic
effect and is useful in pain reduction since hot packs produce an increased blood flow
superficially, thus creating a less dense medium for transmission of ultrasonic, attenuation
may be increased and depth of penetration of ultrasonic reduced.
Cold packs are most often used for analgesia and to decrease acute blood flow after
injury. Because cold is such an effective analgesic, caution must be exercised when using
ultrasonic at higher intensities that produce thermal effects, since patients perception of
temperature and pain is diminished. However in treating acute and postacute injuries, the
combination of cold to reduce blood flow (i.e. swelling) and produce analgesia, and low
intensity ultrasound, for its nonthermal effects that promote soft tissue healing, may be the
treatment of choice. Since cold produces a decrease in blood flow superficially and thus a
more dense medium, superficial attenuation of ultrasonic may be decreased, facilitating
transmission to deeper tissues.
The production, application and therapeutic effects are those of the individual
therapies as described in this text. The justification for the use of combination therapy
is principally the beneficial effect of both modalities may be achieved at the same time,
thus making the therapy efficient, at least in terms of time committed by both therapist
and patient.
A second justification is that there may be an enhancing effect of one therapy upon the
other, making the combination more effective than each therapy alone.
Shock Wave Therapy
Shock wave therapy (SWT) (Fig. 8.17) is a technique in which high pressure sound waves
are used for the treatment of various musculoskeletal conditions. In earlier days, shock-
waves were used in breaking up of kidney stones. Presently, it has being used for the treat-
ment of plantar fasciitis and tennis elbow tendinitis. It has also been found to be effective
in the treatment of patellar tendinitis, supraspinatus tendinitis, bicipital tendinitis, rotator
cuff injuries, achilles tendinitis, pseudoarthrosis, stress fractures, delayed union, early
stages of avascular bone necrosis and shoulder calcification. There is also an FDA study to
treat recalcitrant diabetic wounds.
Basically two forms of shock waves are currently used:
Extracorporeal Shock wave Therapy (ESWT)
Radial Shock wave Therapy (RSWT)
Extracorporeal shockwave therapy (ESWT) devices contain converging focussed shock
waves. Maximum energy is reached at a specific point in the body. These devices produce
a medium to high energy level.
Radial Shock wave Therapy (RSWT) devices contain radial diverging shock waves.
The energy is spread over a large surface area. These devices produce a low to medium
energy level.
Physical principles
A Shock wave is defined as a sonic pulse characterized by:
High peak-pressure (500 bar)
A short lifecycle (10 ms)
Fast pressure rise (< 10 ns)
A broad frequency spectrum (16 Hz20 MHz).
There are a couple of theories as to how ESWT helps promote better healing. The most
accepted one is that the microtrauma of the repeated shock wave to the affected area
creates neo-vascularization (new blood flow) into the area. It is this new blood flow that
promotes tissue healing. The second theory is that in chronic pain, the brain has forgotten
about the pain and is doing nothing to heal the area. By having shock wave therapy a new
inflammatory process is created and the brain can react to it by sending the necessary body
nutrients to the area to promote healing.
Contraindications for this procedure include: neurological and vascular disease of

the foot, history of rupture of the plantar fascial ligament, open bone growth plates,
pregnancy, implanted metal in the area (bone screws and pins) and people on medication
that interferes with blood clotting such as coumadin and prophylactic aspirin.
Dosage Parameters are

Energy: 520 J/cm2, pressure: from 25 bar, number of shocks: 5002000, treatment sessions:
35.
Fig. 8.17: Shock Wave Therapy Apparatus

1. Tennis elbow
2. Golfers elbow
3. Supraspinatus tendinitis
4. de Quervains disease
5. Bicipital tendinitis
6. Subdeltoid bursitis
7. Subacromial bursitis
8. Metatarsalgia.
ULTRASOUND THERAPY

Name
Age
Sex
Occupation
Chief complaints
Family history
Treatment history
Investigations:
ii. Radiological testsX-rays, MRI scan, etc.
Hyperpyrexia
Hypertension
Epileptic patients
Very poor general condition of the patient.
Skin condition
Wound
Tumor
Pregnant uterus.
Two test tubes
One with hot water
One with cold water
Cotton
Gel (Coupling media)
Towels
Pillows
Sand bags.
6. Preparation of the apparatus:

Selection of treatment head
Switching on
Regulation of amplitude
Checking the plugs
Checking the socket
Checking the main wire whether it is properly fitted in the main machine.
Comfortable with good support
9. Treatment:
Checking the apparatus
Placing the treatment head
Knowledge of the details of technique of application
10. Other special points:
Comfort and consideration of patient
Position and posture of physiotherapist
Care of apparatus and patient
Maintaining the record of treatment.
Tennis elbow (Lateral Epicondylitis)

Definition
Tennis elbow is a condition characterized by pain and acute tenderness on the lateral side
of the elbow usually related to the common extensor tendon.
Age: 3045 years
Sex: Equally common in both the sexes
Cause: Excessive use of wrist extensors
for example: a. Carrying a heavy weight
b. Wrong technique at sport
(e.g. tennis, golf, badminton, fencing)
c. Unaccustomed gardening or carpentry.
Pathology
Tear occurs at the tenomuscular junction, in the tendon or at the tenoperiosteal junction.
The resulting inflammation produces exudates in which fibrin forms to heal the torn
tissue. If excessive fibrin is formed fibrous tissue will result in adhesions of the tendon and
neighboring tissues. This causes pain, repeated use and minor injury to tendon prevent
healing and excessive scar tissue form.
Clinical Features
Pain on exertion
Pain over the elbow toward the wrist
Elbow and wrist, restricted rom due to pain
Resisted wrist extension is painful, passive movement is pain-free
Tenderness over the tendon.
Treatment
Acute - Ice towel for 20 minutes
- Rest
- Splint for wrist extension for 2 to 8 weeks
- Strapping.
Modalities Used
Friction for 510 minutes for 4 days
Ultrasound 1 W cm2, in continuous mode for up to 8 minutes
Pulsed electromagnetic energy
Laser.

Sitting with arm on the pillow placed over the couch.
Mode : Continuous/Pulsed
Duration : 58 minutes
Intensity : 0.751.5 W/cm2
GOLFERS ELBOW (Medial Epicondylitis)

Definition
This is a condition characterized by pain and acute tenderness on the medial side of the
elbow. It affects the common flexor origin.
Principles of treatments are the same as for tennis elbow.
Position of the Patient

Sitting with arm on the pillow placed over the couch.
Mode : Continuous/pulsed
Duration : 58 minutes
Intensity : 0.751.5 Watts/cm2
SUPRASPINATUS TENDINITIS
Etiology
This may occur as a result of one accident (e.g. a fall on the shoulder) over exercise
(e.g. aerobics) or a series of minor stresses (e.g. long periods of writing).
Clinical Features
Pain: Toothache type pain is present radiating from the acromion process to the deltoid
insertion.
Painful area: Abduction to 60 degree is pain-free
60 to 120 degree is painful
120 to 180 degree is pain-free.
Movements: Shoulder, arm movements are full (but have a painful arc)
Resisted abduction in outer range is often painful.
Lowering the arm from elevation is very painful. If this movement is resisted the pain
is less. This is a test used to determine whether it is bursitis or tendinitis. Bursitis
remains painful on resisted lowering of the arm.
Reversed glenohumeral rhythmthe scapula moving more than the humerus.
Function: Severely limited in patient who has to carry (e.g. dresses on coat hangers).
Management
Hydrocortisone injection
NSAID
Physiotherapy
Rest in an arm sling
Ultrasoundremove inflammatory exudates. It must be applied to the tendon that is
with the shoulder in extension E1 medial rotation.
Ice towel to the superior aspect of shoulder (10 to 20 minutes).
Exercise
Autoassisted elevation through flexion adduction should be produced once every
hour to prevent adhesion formation, reeducation of glenohumeral rhythm.
Frictions.
DE QUERVAINS DISEASE (Tenosynovitis)

Tenosynovitis is inflammation of the synovial sheath of the tendon (Tendinitis is inflam-
mation of the tendon which does not have a sheath).
De Quervains disease is a chronic constructive tenosynovitis affecting the abductor
pollicis longus and extensor pollicis brevis tendons of the thumb at the wrist.
Clinical Features
Pain along the lateral aspects of the distal end of the radius
Swelling along the tendons
Tender on palpation
Active extension against resistance and passive flexion of the thumb are painful.
Cause: Over use (Using scissors excessively).
Treatment
Rest
Splinting the wrist and thumb in full extension
Administration of the anti-inflammatory drugs
Ultrasound
Low dosage (0.25 W/cm2)
Pulsed mode
Apply along the length of the tendon
Later stages, administration of hydrocortisone.
BICipital TENDINITIS
This tends to occur when the tendon of the long head lies in the bicipital groove. Pain is
provoked by resisted supination of the forearm and flexion of the elbow. Frictions and
ultrasound are the treatment of choice.
SUBDELTOID BURSITIS
Bursitis is inflammation of a bursa. A bursa is a membranous sac lined with endothelial
cells. It may or may not communicate with the synovial membrane of the joint. The function
of the bursa is to prevent friction between two structures (e.g. tendon and bone or tendon
and muscle) or to project bony points.
Common Sites
1. Prepatellar bursitis (Housemaids knee)
2. Suprapatellar bursitis
3. Subdeltoid bursitis
4. Miners or students elbow (olecranon bursitis)
5. Achillodynia (Inflammation of the one of the bursa around the Achilles tendon).
Causes
Trauma
Associated diseaseRA, gout.
Clinical Features
Pain, swelling.
SUBACROMIAL BURSITIS
This condition is characterized by a painful arc on shoulder abduction. It is present between
60 degree on both active and passive movements when the bursa is passing underneath
the acromion process together with supraspinatus tendon, the long head of biceps and the
capsule of the glenohumeral joint, e.g. PEME, ultrasound.
METATARSALGIA
This is the condition in which there is pain in the metatarsal region. It is usually felt under
the metatarsal heads and is commonly found in the middle-aged or elderly and more often
in women than men.
Causes
Metatarsalgia may be due to weak intrinsic muscle allowing the anterior arch to collapse.
It also occurs secondary to hallux valgus, flat feet, talipes equinus or pes caves. Patients
suffering from Rheumatoid arthritis also develops metatarsalgia. Unsuitable foot wear
predisposes this.
Clinical Features
Pain
Walking pattern is affected
Metatarsal heads are usually prominent on the sole of the foot with callosities forming
over the heads.
Treatment
Reeducation of muscles
Ultrasound.
9 Cryotherapy
The application of cold for various therapeutic purposes is called cryotherapy. Cryotherapy
is commonly used in the treatment of acute trauma and subacute injury. The temperature
of the body tissue is reduced and the heat is transferred from the body tissue to the cold
medium. The magnitude of cooling depends upon the area of the body tissue exposed,
temperature of the cooling agent and the duration of exposure. The depth of penetration
is also related to intensity and duration of cold application and the circulatory response to
the body segment exposed. Thus, for a constant source of cooling, the temperature drop in
the tissues will depend upon:
1. The temperature difference between the coolant and the tissues: the colder the
application, the greater the heat loss from the tissues.
2. The thermal conductivity of the tissues: This differs from one area to another. In
general, water-filled tissues, such as muscles, have a high thermal conductivity as
compared to fat or skin. The normal layer of subcutaneous fat serves as a thermal
insulation for the inner tissues so that the heat loss through the tissues and the cold
penetration is largely dependent upon the blood flow.
3. The length of time for which the cold is applied: The amount of energy loss is fully
dependent upon the length of exposure.
4. The size of area that is being cooled: The smaller the area, more will be cooling.
The various techniques that are used for administering cold are:
i. Ice massage
ii. Ice towels
iii. Immersion in cold or cold whirlpool
iv. Ice packs or cold packs
v. Evaporative cooling or vapocoolant sprays
vi. Excitatory cold.
1. Ice massage: In this technique ice is placed in a polythene bag and applied over the
body tissue. Ice cubes, crushed ice or flaked ice, etc. can be used. The ice bag is placed
over the patients tissue and the patient is not allowed to lie over the pack. The pressure
of application should be minimal and the movement of the bag should be to and fro
and circular. The ice can be placed over the body tissue for a period of 1020 minutes.
2. Ice towels: This is a popular method of application because there is little danger of
producing an ice burn. Prepare the ice solution by filling a bucket or bowl with two
parts of flaked or crushed ice to one part water in which two terry towels are immersed.
The surplus water is wrung from towel, leaving as much ice clinging to it as possible. It
is then applied to the part being treated. The towels are changed after every 30 seconds
to 2 minutes. Upto ten towels can be applied consecutively with total treatment time of
1520 minutes.
3. Immersion in cold or cold whirlpool: The part of the body is immersed in cold water
or a whirlpool in which temperature of water is lowered up to 010C. Flaked ice or
crushed ice is used in a solution with water to form slush. Extremities of the body can
be effectively treated with immersion in the cold. The total duration of the treatment is
around 10 minutes in which the patient can immerse in either for a single 10 minutes
session or for a series of shorter immersions until accumulative total of 10 minutes
have been reached.
4. Cold packs: Commercially used cold packs are used for administering cold. These
cold packs contain special material which retains the cold like the silicate gel. These are
available in various sizes and shapes. Different body parts are treated with different
sizes and shapes of cold packs (Fig. 9.1). These packs are stored in a special refrigeration
or freezer for at least 20 minutes to 1 hour before use (Fig. 9.2). The main advantage
of these cold packs are that they are reusable and can contour or mould themselves
according to the body part treated.
5. Evaporative cooling or vapocoolant sprays: The use of vapocoolant sprays are
increasing nowadays. These are being used very commonly in sporting activities or
athletic injuries. The commonly used sprays are fluoromethane or ethyl chloride. The
jet of spray is usually applied from a distance of about 1 feet or 12 inches. Gentle
stretch is applied to the tissues after application of vapocoolant sprays.
Fig. 9.1: Cold packs

Cryotherapy 275
Fig. 9.2: Cold packs unit
6. Excitatory cold: The marked sensory stimulus of ice on the skin can be used to facilitate
contraction of inhibited muscle. Ascertain the spinal root level supply (myotome) of
inhibited muscle and find the area of skin which has same root supply (dermatome).
The ice is stroked quickly three times over the dermatome and skin is then dried.
This sensory stimulus passes via the peripheral nerve and enters the cord through
posterior horn. It raises the level of excitation around the anterior horn cell (as ACH
has connection with these sensory fibers). The increased excitation may supplement
the patients willing effort to make the muscle contract. This technique of quick ice is
often a useful stimulus in aiding voluntary contraction of muscle.
Basic principles
When cold therapy is applied to the tissues, the heat is absorbed from the tissues by the
cooling agent. Ice changes its state from solid to liquid by absorbing heat. A specific amount
of energy is required to change the solid form of ice into water which is called latent heat of fusion.
One gram of ice at 0C requires 336 Joules of energy to convert it into 1 gram of water at
0C, whereas 1 gram of water at 0C requires 155 joules of energy to convert it into 1 gram
of water at 37C. Thus, for cooling the body tissues it is better to use ice for treatment rather
than water.
Physiological effects and therapeutic uses of cold therapy

Effects on Circulatory System and Uses
The initial response of the body tissue to cold is that to preserve the heat. This is accomplished
by an initial phase of local vasoconstriction. When homeostasis is reached and the body
part has become cooled, there follows phase of vasodilatation. Then there follows alternate
periods of vasoconstriction and vasodilatation. This appears as hunting toward the mean
point and is known as Lewis-Hunting reaction (Fig. 9.3).
Fig. 9.3: Lewis-Hunting reaction
The initial phase of vasoconstriction helps to reduce the flow of blood into the tissues
following recent injury. This helps to limit swelling and the extent of tissue damage.
The alternate phases of vasoconstriction and vasodilatation helps removing the waste
products of metabolism like the lactic acid and thus delays fatigue.
Effects on Nervous System and Neural Tissues

The rate of conduction of the nerve fibers is reduced by cold. The A fibers are affected first
followed by B and C fibers.
The major effects of ice application are to relieve pain. The probable mechanism
involved is the stimulation of cold receptors which send back the impulses, which have to
pass into the spinal cord via the posterior root. These impulses which arrives through the
relatively large diameter nerves effectively blocks the pain impulses attempting to gain
access to the cord and thus the pain gate is closed.
The cold stimulus is itself, is a noxious one and can stimulate the midbrain which may
release beta endorphin or enkephalin (the bodys opiate like substances) into the posterior
horn and thus reduces pain.
It is also possible that the increased circulation by the cold could carry away chemical
substances which are stimulating nociceptors and thus the pain is reduced.
One of the major effects of cold therapy is on the muscle tone. The short, brisk applica-
tion of cold is thought to enhance the muscle tone (i.e. excitatory cold), while the prolonged
use of cold (as in immersion of cold) reduces the muscle tone to a greater extent.
Cryotherapy 277

1. Cardiac conditions: The administration of cold therapy in cardiac patients needs
special attention. In patient with a recent myocardial infarction, the application of cold
may cause further drop in blood pressure and further reduces the blood supply of the
heart. The weak heart may collapse immediately.
2. Peripheral nerve injuries: In cases with peripheral nerve injuries, the blood supply
of the peripheral nerves reduces further and may cause its further damage. Also,
the nerve supply of the blood vessels is further delayed causing loss of the normal
response of its cooling. Thus, in the patients with peripheral nerve injuries the applica-
tion of cold should be avoided.
3. Peripheral vascular disease or vasospastic disease: The application of cold should
be avoided in cases of peripheral vascular disease, as the cold may further reduce an
already inadequate blood supply. In cases of vasospastic disease like the Raynauds
disease, the condition may worsen by the application of cold.
4. Psychological or cold sensitive: The patients having fear of the cold may react
adversely. Following the application of cold, they start producing histamine like
substance causing urticaria with skin rash and itching. The application of cold in
psychologically apprehensive persons and the cold sensitive patients is avoided.

Name
Age
Sex
Occupation
Chief complaints
Family history
Treatment history
Investigations:
1. Hematological tests
2. Radiological testsX-rays, MRI scan, etc.
Hypertension
Epileptic patients
Anemia
Menstruation.
Skin condition
Wound
Tumor
Two test tubes:
One with hot water
Towels
Pillows
Sand bags.
6. Preparation of the cold pack or cryotherapy unit.
9. Preparation of the patient:
Explain (Remove the clothing where the area is to be treated)
Testing the skin sensation
Inspection of the part to be treated
Palpation of the part to be treated.
10. Application to the patient:
Development of appropriate cold level
Duration
Safety.
11. Termination:
Inspection of the part (Erythema) or cold burn
Palpating the part (Pain).
12. Record about the patient condition:
Duration of the treatment
Name
Address.
13. Knowledge of dangers:
If cold burn occurs, gently rub the part.
1 4. Knowledge of contraindications.
15. Home instructions.
16. General information.
ANKLE SPRAIN
One of the most frequent injured structures in sports, particularly in basketball and foot-
ball. Ankle sprain is the most common of all the sprains. Lateral ligament sprain accounts
for 85% of all ankle sprains.
Cryotherapy 279
Mechanism of injury: The sudden forceful inversion, plantar flexion and adduction causes
lateral ligament sprain. Lateral ligaments comprises of the following, e.g. the anterior
talofibular ligament, posterior talofibular ligament and the calcaneofibular ligament. The
sudden forceful inversion, plantar flexion and adduction of these ligaments causes sprain.
Grades of Sprain
Grade 1 : Minimal pain and disability: weight bearing not impaired
Grade 2 : Moderate pain and disability: weight bearing difficult
Grade 3 : Severe swelling, no pain, discoloration, no weight bearing possible, significant
functional loss.
Investigation: X-ray: AP, Lateral (to see any associated fracture)
Treatment: PRICES
P : Prevention from the injury
R : Rest (relative rest) to the part
I : Icing (to prevent swelling and pain)
C : Compression (by crepe bandage) of the part
E : Elevation of the part
S : Support.
Cryotherapy is used to prevent swelling and to minimize pain.
Ice bag or cold pack is used for at least 20 minutes. Swelling is minimized and further
injury of the ligament fibers by swelling is also reduced. Compression is followed by crepe
bandage. Ice bag can be used along with compression also. Initially ice can be used for
a period of 24 hours, but can be extended upto 72 hours (depending upon the severity)
following injury.
Gradual exercises are started after 72 hours of the injury. Once swelling and pain
subsides, partial weight bearing can be started.
When partial weight bearing is pain-free, full weightbearing is allowed and early return
to activities is suggested.
MUSCLE CONTUSION/HEMATOMA
Very common in contact sports, cause of injury is direct blow or hit by a blunt object or by
a ball.
Quadriceps contusion is common in football and is also called Charley horse.
Hematoma occurs when a large sized vessel is damaged and blood starts accumulating
in the area.
Clinical Features
Contusion: Pain, swelling, decreased ROM and ecchymosis.
Hematoma: Mass of firm, jelly-like consistency, ecchymosis, decreased ROM and pain.
Investigations
X-rays are usually normal, but beneficial to exclude any fracture.
Treatment
Initial application of ice is very beneficial.
Cold pack is used for subsidizing swelling and to reduce pain. Ice is applied for a period
of at least 20 minutes, and response is seen. If there is reduction in swelling and hematoma,
it can be continued for another 20 minutes after a interval of 10 minutes.
Aspiration of hematoma under strict sterile conditions is indicated in recurrent and
nonsubsidizing hematomas.
10 Biofeedback
Biofeedback is an instrumentation and technique which is used to accurately measure,

process and feedback some reinforcing information via auditory or visual signals by
electronic or electromechanical device especially for therapeutic purposes.
It can also be simply defined as the process of furnishing an individual information of his
body function, so as to get some control over it.
Biofeedback can be used to assess the physiological functions and then to improve it by
having proper control over it. The information regarding various physiological functions
like heart rate, blood pressure, skin temperature, force generated by muscular contraction
or relaxation, range of motion of joints, etc. are recorded and displayed in front of the
patient. Various forms of information can be reinforced back to the patient like kinesthetic,
visual, auditory, cutaneous, vestibular, etc. The patient is made to visualize the functions.
The target is set at the higher or lower sides of the patients normal capacities. The aim is to
achieve the desired targets.
This is not different in principle from the reeducation given by the physiotherapist in
providing feedback for the correction of posture or for the initiation of muscle contrac
tion. Information from the muscle spindles, joint position, joint range of motion, etc. all
gives a source of feedback. Motor functions are thus improved and well controlled by the
patient. It is also considered that feedback should be proportional to the response. A strong
contraction of muscle produces a strong signal. Also, a visual signal by a digital display
is thought to be more effective than an auditory feedback as comparisons are to be made
during further contractions.
Biofeedback Instrumentation
Biofeedback instruments are designed to monitor some physiologic event, objectively
quantify these monitorings and then interpret the measurements as meaningful information.
Sometimes, these units cannot measure a physiologic event directly. Instead they
record some aspects that are highly correlated with the physiologic event.
The most commonly used instruments include these that record peripheral skin
temperatures indicating the extent of vasoconstriction or vasodilation; finger photo transmission
units (photoplethysmograph) that also measure vasoconstriction and vasodilatation; units
that record skin conductance activity indicating sweat gland activity; and units that measure
EMG indicating amount of electrical activity during muscle contraction.
Additionally, there are other types of biofeedback units available including electroen
cephalographs (EEG), pressure transducers and electrogoniometers.
Peripheral skin temperature: Peripheral skin temperature is an indirect measure of the
diameter of peripheral blood vessels. As vessels dilate, more warm blood is delivered to a
particular area, thus increasing the temperature in that area. This effect is easily seen in the
fingers and toes where the surrounding tissue warms and cools rapidly. Variations in skin
temperature seem to be correlated with affective states with a decrease occurring in response
to stress or fear. Temperature changes are usually measured in degrees Fahrenheit.
Finger photo transmission: The degree of peripheral vasoconstriction can also be measured
indirectly using a photo plethysmograph. This instrument monitors the amount of light
that can pass through a finger or toe, reflex off a bone, and pass back through the soft
tissue to a light sensor. As the volume of blood in a given area increases, the amount
of light detected by the sensor decreases thus giving some indication of blood volume.
Only changes in blood volume can be detected since there are no standardized units of
measures. These instruments are used most often to monitor pulse.
Skin Conductance Activity: Sweat gland activity can be indirectly measured by
determining electro dermal activity most commonly referred to as the galvanic skin
response (GSR). Sweat contains salt, which increases electrical conductivity. Thus sweaty
skin is more conductive than dry skin. This instrument applies a very small electrical
voltage to the skin, usually on the palmar surface of the hand or the volar surface of the
fingers. Measuring skin conductance is a technique useful in objectively assessing psycho
physiologic arousal and is most often used in lie detector testing.
EMG Biofeedback: Electromyogram biofeedback is certainly the most typically used of
all the biofeedback modalities in a therapeutic setting. Muscle contraction results from the
more or less synchronous contraction of individual muscle fibres that compose a muscle.
Individual muscle fibres are innervated by nerves that collectively comprise a motor unit.
The axon of that motor unit conducts an action potential to the neuromuscular junction
where a neurotransmitter substance (acetylcholine) is released. As this neurotransmitter
binds to receptor sites on the sarcolemma, depolarization of that muscle fibre occurs in both
directions along the muscle fibre, creating movement of ions and thus an electrochemical
gradient around the muscle fibre. Changes in potential difference or voltage associated
with depolarization can be detected by an electrode placed in closed proximity to the
muscle fibre.
The raw EMG activity is usually displayed visually on an oscilloscope. On most
biofeedback units, integrated EMG activity is visually presented as a line traveling across
a monitor, as a light or series of lights that go on and off, or as a bar graph that changes
dimensions, all of which change in response to the incoming integrated signal. If the
biofeedback unit uses some forms of a meter, it may either be calibrated in objective units
such as micro volts or given some relative scale to measure. Meters may either be analogue
or digital. Analogue meters have a continuous scale and a needle that indicates the level
of electrical activity within a particular range. Digital meters display only a number. They
are very simple and easy to read. However, the disadvantage of a digital meter is that it is
more difficult to tell where in a given range the signal falls.
Biofeedback 283
On some biofeedback units, raw EMG activity is presented in an audio format. The
majority of biofeedback units have audiofeedback along with which produces some tone,
buzzing, beeping or clicking. An increase in the pitch of a tone, buzz or beep or an increase
in the frequency of clicking indicates an increase in the level of EMG activity. This would
be most useful for individuals who need to strengthen muscle contractions. Conversely,
decreases in pitch or frequency indicating a decrease in EMG activity would be most useful
in teaching athletes to relax.
Specific treatment protocols are required for reproducible results such as skin preparation,
application of electrodes, selection of feedback or output modes, and sensitivity settings.
General Principles
A behavioral positive reinforcement or reward model is usually employed with biofeed
back techniques. Simply stated, when patients generate appropriate motor behaviors, they
are positively reinforced. The audio and visual feedback stimuli, and other nonverbal
information, are usually much faster and more accurate than the therapists comments.
Unlike other interventions, the benefits of accomplishing small changes in motor behavior
in the desired direction can be reinforced, which should speed the rehabilitation process.
In behavioral learning terminology, the therapist uses the biofeedback signal to shape the
motor behavior by reinforcing the patients successive approximations to the goal behavior
or functional outcome.
When the patient succeeds in controlling the signal, the therapist must relate it to
the underlying motor behavior and then reestablish the expected outcomes. Reinforcing
already-learned behaviors is of course, futile, so the machines thre shold should be
monitored frequently, increasing the tasks difficulty as motor skills progress.
Feedback can be intrinsic or extrinsic. Intrinsic feedback is the bodys internal feedback
mechanism, which uses visual, auditory, vestibular and proprioceptive mechanisms.
Extrinsic feedback is any feedback derived from an external source (e.g. a biofeedback
signal or physical therapists comments) that augments intrinsic feedback.
Biofeedback in Rehabilitation
When using biofeedback, the patient must:
1. Understand the relationship of the electronic signal with the desired functional task
2. Practice controlling the biofeedback signals
3. Perform the functional task until it is mastered and the patient no longer needs the
biofeedback.
Conventional neuromuscular reeducation is based heavily on providing patients with
helpful comments (feedback) to assist their recovery of previously acquired skills. The
therapists job is to focus the patients attention on the underlying motor programs and
biomechanical schema required to recoup those skills.
Recent applications of biofeedback have been directed at muscle imbalances and the
fine tuning of motor control. The focus, for example, with the quadriceps, might be a
balanced vastus medialis oblique:vastus lateralis (VMO:VL) ratio and not merely gross
strength.
Biofeedback is simply one technique that therapists may employ to help convey their
message about motor programs and biomechanical schemata to the patient. Biofeedback
can assist the rehabilitation process by:
1. Providing a clear treatment outcome or goal for the patient to achieve.
2. Permitting the therapist and patient to experiment with various strategies (processes)
that generate motor patterns to achieve the desired outcome or goal.
3. Reinforcement for getting the appropriate motor behavior.
4. Providing a process which gives orientation, time and accurate knowledge of results
for the patients efforts.
The machine should be set to give auditory or visual feedback that corresponds to
the desired motor behavior. For example, if spastic antagonist are to be monitored, the
patient should be instructed to decrease the EMG activity; the biofeedback device is set to
flash a light in order to provide signal of this outcome. Alternatively, an electrogoniometer
can be used which changes the pitch of a buzzer as the joint is moved in the appropriate
direction. In brief, biofeedback techniques are used to augment the patients sensory
feedback mechanism through specific and precise information about the body physiologic
processes that might otherwise be inaccessible.
Use of EMG Biofeedback for Neuromuscular Reeducation

Electromyogram (EMG) biofeedback is useful for neuromuscular reeducation. The basic
EMG device comprises of one ground and two surface electrodes, an amplifier, an audio
speaker and a video display. A surface EMG for skeletal muscle activity can be compared
with electrocardiography (ECG) being done for heart. The EMG signal is transmitted from
the muscle through the skin, through the electrode paste, through the electrodes, through
the wires and then to the amplifier. The equipment is quite complex and for skilled use
a good understanding of the EMG signals characteristics is required. The EMG display
bears an approximate relationship to the magnitude of the muscle contraction which
causes it. The relationship is quite complicated because the motor unit action potential that
occurs cannot all be equally detected and recorded. However, for biofeedback purposes
the overall effect of stronger contractions leads to louder clicks and a large display on the
screen are adequate.
Limitations of Biofeedback
The biofeedback must be relevant, accurate and rapid to enhance motor learning. If any of
these three elements is missing, the traditional form of feedback, i.e. verbal feedback can
be used which is more convenient.
1. Relevancy: Useful relevant information is important for the desired motor response.
It should neither be too short or too long. Electromyogram (EMG) biofeedback can
provide relevant information about the motor unit activity which cannot be available
otherwise.
2. Accuracy: The biofeedback device and the way, it is used, should provide an accurate
information. Many believe that the EMG signals are not sufficient to constitute true
process of feedback. They use specific devices that directly measure force or joint
Biofeedback 285
range of motion. For obtaining accurate results, appropriate biofeedback device and
proper technique of application should be used.
3. Rapid information: All EMG processes delay electrical events during signal
amplification and conversion to audio speaker and visual meter because of inherent
delays from the electrical circuits. Most commercial EMG biofeedback instruments
gives 50 to 100 millisecond delay before the signal reaches to the ears and eyes of the
patients. Biofeedback to be useful must provide immediate rapid information. While
biofeedback is employed, the movements are necessarily closed loop.
In brief, the information used to be feedback to patients must be accurate, relevant and
rapid for effective therapeutic use. Therapists must choose the appropriate instrument or
device that provides the most meaningful information to the patients.
Uses of Biofeedback
1. Peripheral nerve injuries: Biofeedback can be used in the treatment of recovering
peripheral injuries. Once a motor unit activity has been detected on electromyography,
voluntary repetition can be encouraged. Electromyogram (EMG) biofeedback provides a
means of extending the recognition of least possible motor activity and then quantifying
it to some extent. In cases of nerve transplant or tendon transplant biofeedback can be
useful to provide assistance to the patient to learn the new muscle action.
2. Spinal cord injury: Biofeedback techniques have been recommended and applied in
the rehabilitation of spinal cord injury patients. Feedback is provided to the patient
to perform voluntary action in paralysed muscle. After several repetitions gradual
positive response can be seen.
3. Hemiplegia: Several studies have found biofeedback to be useful method of treatment
in hemiplegia. Biofeedback is commonly used into reeducate controlled dorsiflexion
of foot and thus to improve gait. It can also be used for deltoid in order to improve
shoulder control.
4. Dystonic conditions: Dystonic conditions in which the patient suffers uncontrollable
movements and postures can also be treated with EMG biofeedback. Spasmodic
torticollis is one such condition in which voluntary muscle contractions are used to
inhibit inappropriate neck movements.
5. Treating spasticity: Several spastic conditions such as cerebral palsy, multiple
sclerosis, head injury, etc. can be treated with biofeedback in order to reduce and
control spasticity. It should be noted that in all neurological disorders treated by
biofeedback, it is assumed that there are some intact neuronal pathways available to
suppress spasticity.
6. Postural control: Biofeedback devices are used to have appropriate postural control. A
trunk inclination monitor which signal tilt can be used for the treatment of low back
ache. A tilt away from normal can provide an audiofeedback and thus helps correcting
posture.
7. Muscle strengthening: Muscle strength training devices have an electronic display
which indicates the strength in a muscle and acts as a biofeedback to the exercising
muscles. It provides a feedback by display of force produced by the contracting muscle
and thus helps to strength the muscle further.
8. Functional reeducation: Biofeedback can be effectively used in improving functional

reeducation. The biofeedback devices can be used in various ways to encourage
repeated practice of a particular movement to improve function.
9. Providing relaxation: The electrical resistance of hand or fingers are measured and
displayed. Increase or decrease in stress is reflected in the amount of sweating that
occurs which in turn determines the skin resistance. Biofeedback devices are used
effectively for providing general relaxation to the body. Pulse rate or respiratory rate is
recorded by some apparatus and findings are displayed to the patient. The patient tries
to control and regulate the pulse and respiratory rate and thus inducing relaxation.
11 Electromyography
Electromyography is basically the study of motor unit activity. In electromyography, the

study of the electrical activity of contracting muscle provides information concerning the
structure and function of the motor units. Motor units are composed of one anterior horn
cell, one axon, its neuromuscular junctions and all the muscle fibers innervated by the axon
(Fig. 11.1). The nerve cell and the muscle fiber it supplies are defined as a motor unit.
Fig. 11.1: The motor unit
Whenever a muscle fiber contracts, the surface membrane undergoes depolarization

so that an action potential is recorded from the fiber. When the fibers of a motor unit
are activated, they contract nearly but not quite synchronously and their action potential
is added up and hence relatively large complex potential known as motor unit action
potential is recorded. Electromyography makes it possible to localize the site of pathology
affecting either muscle or its innervation and also provides evidence regarding the nature
of pathological process.
Electromyography is a technique by which the action potentials of contracting muscle
fibers and motor units are recorded and displayed. Recording the EMG requires a three
phase system:
1. an input phase
2. a processor phase
3. an output phase.
An input phase includes electrodes to pick up electrical potential from contracting
muscle, a processor phase amplifies the very small electrical potentials and an output
phase includes the display and analysis of electrical potential by visual and auditory
means.
Types of Electromyography
1. Diagnostic or clinical electromyography
2. Kinesiological electromyography
Diagnostic or clinical electromyography: It is used for the study of diseases of muscles,
neuromuscular junctions and nerves. It is used for the purpose of electrodiagnosis. The
electric potentials from the skeletal muscle fibers are recorded and analysed for the study
of some disease processes. Diseases in which the structure and function of the motor
unit is affected, the motor unit action potential may have an abnormal configuration and
the pattern of motor unit activity during voluntary contraction may be altered. Healthy
muscle fibers contract only when they are activated by neurons and hence under normal
conditions, only the motor unit action potentials are seen. In neuromuscular disease, single
muscle fiber may contract apparently spontaneously and this may be recognized by the
action potential derived from small group of fibers.
Kinesiological electromyography: It is used in the study of muscle activity and to
establish the role of various muscles in specific activities. Kinesiological EMG is beneficial
for producing the objective means for documenting the effects of treatment on muscle
impairments. It is used to examine the muscle function during the specific, purposeful
tasks or therapeutic regimen.
Motor Unit Action Potential

The motor unit action potential (MUAP) means when the depolarization of muscle fibres,
which results in the electrical activity and graphically recorded by electromyogram, it
represents potential derived from group of muscle fibres that are contracting nearly
synchronously and are situated fairly close together and frequently activated by a
single neuron. The motor unit action potential therefore represents a sample of activity
of the fibres of motor unit and its characteristics are influenced by position of electrodes
in relation to fibres of unit. The muscle action potential can be recorded as a monophasic
wave in a non conducting medium. Recording in a conducting medium, the current
flow generated by the potential is same as a relative positive wave when recorded
from a distance. Electromyography refers to recording of action potentials of muscle
fibres firing singly or in groups near the needle electrode in a muscle. The distance of
recording electrodes from the muscle fibre determines the rise time and fall time of the
muscle fibres.
Electromyography 289
The Components of Electromyography

The components of electromyography apparatus are:
1. Electrodes
2. Amplifier system
3. Display system.
1. The Electrodes: They are used in the input phase for picking up of electrical potentials
from the contracting muscle fibres. The electrodes are of following types:
a. Surface electrodes
b. Needle electrodes
c. Fine wire indwelling electrodes
d. Single fibre needle electrodes
e. Macroelectrode
f. Intra cellular electrode
g. Multi lead electrode
a. Surface electrodes: Surface electrodes are basically used for kinesiological investiga-
tions. These are made up of small disc of electrodes most commonly of silver-silver
chloride. The diameter of electrode is generally 3 to 5 mm (Fig. 11.2). Skin prepara-
tions are important in order to reduce skin resistance. Skin preparation includes
washing of skin, rubbing to remove dry and dead cells and cleaning with alcohol to
remove dust. They are generally considered adequate for monitoring large superfi-
cial muscles or muscle groups. They are not considered selective enough to record
activity accurately from an individual motor unit or from specific small or deep
muscles unless special recording procedures with adequate amplifiers and filtering
procedures are used.
Fig. 11.2: Surface electrodes
b. Needle electrodes: Needle electrodes are used for clinical electromyography for
recording single motor unit potential from different parts of a muscle. The different
types of needle electrodes used are:
i. Concentric (coaxial) needle electrode: This type of electrode consists of a
stainless steel cannula through which a single wire of platinum or silver comes
out. The cannula shaft and wire are insulated from each other and only their
tips are exposed. They act as electrodes and potential difference between them
is thus recorded (Fig. 11.3A).
ii. Monopolar needle electrode: These are composed of single fine needle which
is insulated except at its tip. A second surface electrode is placed on the skin
near the site of insertion which serves as a reference electrode. These electrodes
are less painful than concentric electrodes because they are much smaller in
diameter (Fig. 11.3B).
iii. Bipolar needle electrode: These consist of a cannula containing two insulated
wires with their bare tips. The bared tips of both wires act as the two electrodes
and the needle serves as the ground (Fig. 11.3C).
Figs 11.3A to C: Different types of needles electrodes
c. Fine wire indwelling electrodes: These are used for kinesiological study of small
and deep muscle. It is made by using two fine wires of small diameter with
polyurethane coating or nylon insulation. Insulation is removed from the tip of
the wires and hooks are created to keep the wires imbedded while the needle is
removed from the muscle (Fig. 11.4).
d. Single fibre needle electrodes: These are concentric wires of 25 m diameter and
contain stainless steel cannula of 0.5 mm diameter. This gives information about
propagation velocity along the muscle fibres. Single fibre needle records from a
small area and hence it cannot be used for motor estimation of motor unit size.
Single fibre EMG is employed to study neuromuscular transmission abnormality
and fibre density.
e. Macroelectrode: Macroelectrode is a concentric needle electrode of 15 mm shaft.
It records from a large number of motor units along the shaft of the needle. The
recording from one motor unit is separated by using a single fibre needle attached
to macroelectrode in the midshaft. This method gives information concerning the
Fig. 11.4: Fine-wire indwelling electrodes
whole motor unit but has not at present widely applied to the study of pathological
motor units.
f. Intra cellular electrode: This is an extremely fine electrode of diameter 0.5 m and
is used to record the potential changes inside the membrane across a cell. It is made
so fine so as to penetrate deep inside a cell or intracellular matrix.
g. Multi lead electrode: This electrode consists of a common steel cannula which
comprises of at least three insulated electrodes at regular intervals inside it.
In addition to recording electrodes (surface or needle), a ground electrode must be applied
in order to cancel the interference effect of the external electrical noise and vibrations such
as caused by mobile phones, fluorescent lights, broadcasting facilities, elevators and other
electrical appliances. The ground electrode is a surface electrode which is attached to the
skin near the recording electrode but usually not over the muscle.
The myoelectric signal: The EMG electrodes convert bioelectric signal resulting from
muscle or nerve depolarization into an electrical potential capable of being processed by
an amplifier. The difference of electric potential between the two recording electrodes
is processed. The potential difference is measured in volts. The amplitude or height of
potential is measured in microvolts. The potential difference and the amplitude are directly
proportional to each other, the greater the potential difference between the electrodes the
greater the amplitude. The amplitude of motor unit potential is measured from the highest
to the lowest point (i.e. from peak to peak).
2. The Amplifier system: Before the motor unit potential can be visualized, it is necessary
to amplify the small myoelectric signals. An amplifier converts the electric signal large
enough to be displayed.
Differential amplifier: The electric potential is composed of the EMG signal from
the muscle contraction and unwanted noise from the static electricity in the air and
power lines. To control for the unwanted part of the signal, the differential amplifier
is used, as noise is transmitted to the amplifier as a common mode signal when the
difference of potential is reduced at both the ends, the noise being cancelled out both
the ends of amplifier.
Common mode rejection ratio: Actually, noise is not eliminated completely in
the differential amplifier. Some of the recorded voltage includes noise. The common
mode rejection ratio (CMRR) is a measure of how much the desired signal voltage is
amplified relative to the unwanted signal. A CMRR of 1000:1 indicates that the wanted
signal is amplified 1000 times more than the noise. It can also be expressed in decibels
(dB). A good differential amplifier should have a CMRR exceeding 100000 : 1. The higher
is this value, the better it is.
Signal to noise ratio: Noise can be generated internally by the components of
the amplifier system such as resistors, transistors, or the circuit. This noise can be
observed by the hissing sound on an oscilloscope. The factor that reflects the ability
of the amplifier to limit this noise relative to the amplified signal is the signal to noise
ratio. This ratio can also be described as the wanted signal to the unwanted signal.
Gain: The gain refers to the ratio of the output level of signal to the input level
of signal. This characteristic refers to the amplifiers ability to amplify the signals. A
higher gain will make a smaller signal to appear larger on the display system.
Input impedance: Impedance is a resistive property present in the alternating
current circuits. Impedance is present at the input of the amplifier and as well as at the
output of the electrodes and they are directly related to the voltage. As per law, if the
impedance at the amplifier is more than the impedance at the electrodes, the voltage
will drop more and more accurately it represents the signal. On contrary, if the imped-
ance at the electrodes is more than the impedance at the amplifier, the voltage drop
will be less. Also, the impedance depends on many factors such as skin resistance,
material of the electrodes, size of the electrodes, length of the leads and electrolyte, etc.
Blood, skin and adipose tissue also offer resistance to the electrical field.
Frequency band width: The EMG waveforms as processed by an amplifier are
actually the summation of signals of varying frequencies. The frequency is measured
in Hertz. The frequency of an EMG signal is inversely proportional to the interelectrode
separation. Consequently the frequency spectrum extends from 10 to 500 Hertz for
most surface electrodes and from 10 to 1000 Hertz for fine wire electrodes.
3. The display system: The amplified or processed signal is displayed in a useful manner.
The form of output used depends upon the desired information and the instrumentation
available. The electrical signal can be displayed visually on a cathode ray oscilloscope or
computer monitor for analysis.
A cathode ray oscilloscope consists of the electron gun, screen, horizontal and
vertical plates. The working of the cathode ray oscilloscope is, the electron gun which
projects the electron beam toward the screen interiorly is phosphorescent in nature.
There are two set of plates that is vertical and horizontal arranged, as the electron
beam passes there is deflection in the vertical plate and sweep at the horizontal plate
this is shown at vertical plate signal voltage in microvolts and sweep at the horizontal
plate shows the duration of signal in millisecond but by conversion there is positive
as well as negative deflection and below base line. These signals are displayed by the
loudspeaker which records both the cathode ray oscilloscope image sound and ink
pen writers are also sometimes used, but they are limited to frequencies. Alternatively
camera can be connected to the cathode ray oscilloscope and then photographs can
be made for permanent record. Computers can also be used so that it performs the
complex analysis of motor unit potentials and send results to printer.
The data received can also be stored and monitored on a computer based system
(Fig. 11.5). It can be stored in an analog or digital form. The conversion process is
referred to as analog to digital conversion and the device that is used to perform this
Fig. 11.5: The EMG recording system
task is called A to D converters. The motor unit potential can also be converted into
the sound in the same way as the radio signal is processed. For the same reason that
every motor unit potential will look different it will also sound different. Normal and
abnormal potentials have distinctive sounds that are helpful in distinguishing them.
The electromyographic examination

An electromyography is used to assess the integrity of neuromuscular system including
the upper and lower motor neuron, the neuromuscular junction and muscle fibres. The test
is done for detecting the muscle action potential in a group or individual in the different
stage of contraction. Peripheral nerve lesions are also detected by electromyography.
The technique of EMG recording: the patient is asked to relax and the needle is
inserted inside the muscle, simultaneously spontaneous burst of potential is observed. The
insertion activity is observed when the needle breaks the fibre membrane. The equipment
of EMG recording is set up at sweep speed 510 ms/div; amplification 50 V/division for
studying spontaneous activity and 200 V/divisions for motor unit potentials and filter
setting 2010000 Hz, the duration of MUPs should be measured at a gain of 100V/div
and sweep speed of 5 ms/div and low filter at 23 Hz.
In needle electromyography, following types of activities are recorded:
1. Insertional activity
2. Spontaneous activity
3. Motor unit potential
4. Recruitment pattern.
1. Insertional activity: Introduction of the needle into the muscle normally produces a
brief burst of electrical activity due to mechanical damage by needle movement and
it lasts slightly exceeding the needle movement (0.50.10 sec). It appears as positive
or negative high frequency spike in a cluster. Insertional activity may be increased
in denervated muscles and myotonia whereas it is reduced in periodic paralysis
during the attack and myopathies when muscle is replaced by connective tissue or
fat. Prolonged insertional activity is sometimes found in normal individuals which
is diagnosed by its widespread distribution. Trains of regularly firing positive waves
sometimes are familial and may be due to a subclinical myotonia. On the other hand in
muscular individuals, the insertional activity is reduced especially in the calf muscles.
2. Spontaneous activity: When the cessation or decay of insertional activity occurs after
a second or so, there is no spontaneous activity in a normal muscle, which is called
Electrical silence. Observation of silence in the relaxed state is an important part of the
EMG examination. In the end plate zone however miniature end plate potentials are
spontaneously recorded instead of silence. On needle recording, end plate potentials
appear as monophasic negative waves of less than 100 V and duration of 13 ms.
The end plate potentials are usually seen with an irregular baseline and are called as
end plate noise. In the end plate region, action potentials which are brief, spiky, rapid
and irregular with an initial negative deflection are known as end plate spikes. These
are compared with the sound of sputtering fat in a frying pan. End plate spikes are
due to mechanical activation of nerve terminals by the needle. To avoid the normally
occurring spontaneous end plate activities, the needle should be introduced slightly
away from the motor point.
3. Normal motor unit action potential: The normal motor unit action potential is the
sum of electrical potential of the muscle fibres present in the single motor unit, having
the capability of being recorded by the electrodes. The normal motor unit action
potential depends on the given five factors that is amplitude, duration, shape, sound
and frequency.
In normal muscle, the amplitude of a single motor unit action potential may range
from 300 mV to 5 mV from peak to peak. The total duration measured from initial
baseline will normally range from 3 to 16 m-sec.
The shape of a motor unit action potential is diphasic or triphasic with a phase
representing a section of potential. There are sometimes polyphasic potentials in two
or more phase.
The sound is a clear distinct thump and there is capability of the motor unit that it
will fire up to 15 times per second with strong contraction, usually when muscle is at
rest it represents electrical silence but if there is an activity it is considered as abnormal
and denoted by spontaneous activity which is not represented by normal voluntary
muscle contraction.
Duration of motor unit action potential: The duration of motor unit action potential
is measured from the initial take off to the point of return to the baseline. The duration
of motor unit action potential normally varies from 5 to 15 ms depending upon the
age of the patients, muscle examined and temperature. The facial muscles have a very
short duration 4.3 to 7.5 cm compared to limb muscles. Duration of biceps brachii
is 7.3 to 12.8 ms and that of interossei 7.9 14.2 ms. The duration of the motor unit
action potential is greatly influenced by age of the subject; motor unit action potential
is short in children, longer in adults and still longer in elderly persons. Temperature
also influences the duration significantly; 7C cooling increases the duration of motor
unit action potential by 10 30%. The duration of motor unit action potential is a
measure of conduction velocity, length of muscle fibre, membrane excitability and
synchrony of different muscle fibres of a motor unit. The initial and the terminal low
amplitude portions of motor unit potential are also contributed by the fibres more than
1 mm away from the recording electrode. The duration of motor unit action potential,
therefore, is much less influenced by the distance of recording electrode compared to
the amplitude.
Rise time of motor unit action potential: The rise time of motor unit action poten-
tial is the duration from initial positive to subsequent negative peak. It is an indicator
of the distance of needle electrode from the muscle fibre. A greater rise time is attrib-
uted to resistance and capacitance of the intervening tissue.
Amplitude of motor unit potential: The amplitude of motor unit action potential is
measured peak to peak. It depends upon size and density of muscle fibre, synchrony
of firing, proximity of needle to the muscle fibre, age of the subject, muscle examined
and muscle temperature. Decreasing muscle temperature results in higher amplitude
and longer duration of MUPs.
Phase of motor unit action potential: Motor unit potential recorded by a concen-
tric or monopolar needle reveals as inverted triphasic potential (positive-negative-
positive). The phase is defined as the portion of MUP between departure and return
to the baseline. A motor unit action potential with more than four phases is called as
polyphasic potential. Some potentials show directional changes without crossing the
baseline and these are known as turns.
4. Recruitment pattern: The firing rate of motor unit action potential for a muscle is
constant. When voluntary contractions are initiated, the motor units are recruited in
an orderly fashion, the smallest appearing first, larger later and largest still later. This
pattern of recruitment is based on Hannemans size principle. If there is loss of motor
unit action potential, the rate of firing of individual potentials during muscle contraction
will be out of proportion to the number of firing and it is termed as reduced recruit-
ment. During strong voluntary contraction, normally there is dense pattern of multiple
superimposed potentials which are called as interference pattern. Less dense pattern
may occur with a loss of motor units, poor effort or in upper motor neuron lesions.
Abnormal spontaneous potentials: As a normal muscle at rest exhibits electrical silence,
any activity seen during the relaxed state is considered as abnormal. These activities are
termed as spontaneous because these are not produced by the voluntary contraction of the
muscles. The common abnormal spontaneous activities are:
1. Fibrillation potential
2. Positive sharp waves
3. Fasciculation potential
4. Repetitive discharges.
1. Fibrillation potential: Fibrillations are spontaneously occurring action potentials
from a single muscle fibre. Fibrillation potential is seen in the denervated muscle as
they give spontaneous discharges due to circulating acetyle choline. Fibrillation poten-
tial are classically indicative of lower motor neuron disorders such as peripheral nerve
lesions, anterior horn cell disease, radiculopathies, and polyneuropathies with axonal
degeneration. Fibrillation potentials are found to a lesser extent in myopathic diseases
such as muscular dystrophy, dermatomyositis, polymyositis and myasthenia gravis.
2. Positive sharp waves: Positive sharp waves are found in denervated muscles at rest
and are usually accompanied by fibrillation potentials. These are recorded as a biphasic
with a sharp initial positive deflection followed by slow negative phase. Positive sharp
waves are seen in primary muscle disease like muscular dystrophy, polymyositis but
sometimes it is also seen in upper motor neuron lesions.
3. Fasciculation potential: Fasciculation potentials are random twitching of muscle
fibre or a group and may be visible through skin. These are spontaneous potentials
seen with irritation or degeneration of anterior horn cell, nerve root compression and
muscle spasm or cramps. They may be biphasic, triphasic or polyphasic.
4. Repetitive discharges: These are also called as bizarre high-frequency discharges.
These are characterized by an extended train of potentials of various forms. These are
seen with lesions of the anterior horn cells, peripheral nerves and with the myopathies.
Normalization of EMG: It is not reasonable or justified to compare the EMG activity of one
muscle to another or from one person to another. This is because of the variability inherent
in the EMG signal and interindividual differences in anatomy and movement. Therefore,
some form of normalization is required to validate these studies, as for many studies the
quantified EMG signal is used to compare activity between different muscles or subjects.
Kinesiological Electromyography
Kinesiological electromyography is used to study the muscle activity and to establish

the role of various muscles in specific activities. Surface electromyography can be used
as a kinesiological tool to examine muscle function during specific and purpose tasks.
Kinesiological electromyography presents an objective means for documenting the effect
of treatment on muscle impairements. Surface as well as fine wire indwelling electrodes
is used for kinesilogical study. Smaller muscles obviously require the use of smaller
electrodes, with a small interelectrode distance. The ground electrode should be located
reasonably close to the recording electrodes. The EMG signal can be stored, averaged and
sampled in a variety of ways to permit detailed and complete analysis. For kinesiological
electromyography the therapist should be interested at looking the overall muscle activity
and quantification of the signal is often desired to describe and compare changes in the
magnitude and pattern of the muscle response.
Nerve conduction velocity
Nerve conduction velocity (NCV) tests are used to determine the speed with which a
peripheral motor or sensory nerve conducts an impulse. EMG and NCV are two important
diagnostic procedures that can provide complete information about the extent of nerve injury
or muscle disease. These data can be valuable for diagnosis of disease and determination of
rehabilitation goals for patients with musculoskeletal and neuromuscular disorders.
Nerve conduction velocity can be tested for any superficial nerve that is superficial
enough to be stimulated through the skin at two different points. Most commonly NCV
test is performed on ulnar, median, peroneal and posterior tibial nerves and less commonly
on radial, femoral and sciatic nerves.
Principles of Motor Nerve Conduction

Motor nerve conduction velocity is calculated measuring the distance between two points
of stimulation in mm which is divided by the latency difference in ms. The nerve conduc-
tion velocity is expressed as m/sec. Measurement of latency difference between the two
points of stimulations eliminates the effect of residual latency.
D
Conduction velocity =
PL DL
Where, D = distance between proximal and distal stimulation in mm

DL = distal latency in m-sec
PL = proximal latency in m-sec
The motor nerve is stimulated at least at two points along its course (Fig. 11.6).
The stimulating electrode is typically a two pronged bipolar electrode with the cathode
and anode. Small surface electrodes are usually used to record the evoked potential from
the test muscle, although needle electrodes may be used when responses are very weak.
A ground electrode is placed between the stimulating and recording electrodes. The pulse
is adjusted to record a compound muscle action potential. A biphasic action potential
with the initial negativity is thus recorded. For accurate motor nerve conduction velocity
measurement, the distance between two points of stimulation should be at least 10 cm. This
reduces the error due to faulty distance measurement. Stimulation at shorter segments of
the nerve, however, is necessary in the evaluation of focal compressive neuropathies, e.g.
Fig. 11.6: Principles of motor nerve conduction

R = recording electrode
G = ground electrode between stimulating and recording electrode
S1 = stimulation at wrist
S2 = stimualtion at elbow
carpal tunnel syndrome. In a diseased nerve, the excitability is reduced and the current
requirement may be much higher than normal.
The measurement for motor nerve conduction study includes the onset latency, dura-
tion and amplitude of compound muscle action potential (CMAP) and nerve conduction
velocity. The onset latency is the time in ms from the stimulus artifact to the first negative
deflection of CMAP. The amplitude of CMAP is measured from baseline to the negative
peak (base to peak) or between negative and positive peaks (peak to peak) (Fig. 11.7).
The duration of CMAP is measured from the onset to the negative or positive peak or
the final return of waveform to the baseline (Fig. 11.8).
Fig. 11.7: Measurement of CMAP latency and Fig. 11.8: Measurement of duration of CMAP
amplitude
a = onset to negative peak
L = onset latency b = onset to positive peak
a = base to peak amplitude c = onset to final return to base line
b = peak to peak amplitude
Principles of Sensory Nerve Conduction

The sensory conduction can be measured orthodromically or antidromically. In orthodromic
conduction, a distal portion of the nerve, e.g. digital nerve is stimulated and sensory nerve
action potential (SNAP) is recorded at a proximal point along the nerve (Fig. 11.9). In
antidromic sensory nerve conduction, the nerve is stimulated at a proximal point and nerve
action potential is recorded distally. In antidromic sensory nerve conduction measurement,
the action potential may be obscured by superimposed muscle action potential, which is
elicited due to simultaneous stimulation of motor axon in the mixed nerve. For orthodromic
conduction, ring electrodes are preferred to stimulate the digital nerve; whereas surface
stimulating electrodes are commonly used for antidromic stimulation.
Recording is also done by surface electrodes; however, in difficult situations needle
electrode may be tried. Similar to motor nerve conduction study, the sensory nerve
conduction measurement includes onset latency, amplitude, duration of sensory nerve
action potential (SNAP) and nerve conduction velocity (Fig. 11.10).
The latency of orthodromic potential is measured from the stimulus artifact to the
initial positive or subsequent negative peak. The latency following orthodromic stimula
Fig. 11.9: Principles of orthodromic sensory conduction

R = recording electrode
G = ground electrode between stimulating and recording electrode
S = stimulating site
Fig.11.10: Measurement of latency of SNAP
tion is shorter compared to antidromic. In practice, however, both orthodromic and

antidromic methods provide the desired information. The initial positive peak in sensory
nerve action potential giving it a triphasic appearance is a feature of orthodromic potential.
In antidromic potential, the initial positivity in sensory nerve action potential is lacking.
The sensory nerve action potential amplitude is measured from baseline to negative
peak or from positive to negative peak (Fig. 11.11). The sensory nerve action potential
recorded with a surface electrode is of higher amplitude in antidromic recording compared
to orthodromic; because nerves are closer to the recording electrode especially in digital
nerves.
Fig. 11.11: Measurement of SNAP amplitude

a = base to peak
b = peak to peak
The duration of sensory nerve action potential is measured from the initial positive
peak to the intersection between the descending phase and the baseline or to the negative
or subsequent positive peak or return to the baseline (Fig. 11.12). The amplitude of
sensory nerve action potential is variable not only in different normal subjects but also in
the same individual on two sides. Sensory nerve action potential unlike motor conduction
velocity may be measured by stimulating at a single stimulation site; because the residual
latency which comprises of neuromuscular transmission time and muscle propagation
time is not applicable in sensory nerve conduction. Thus, the sensory conduction velocity
is calculated by dividing the distance (mm) between stimulating and recording site by
the latency (ms). The sensory nerve action potential amplitude shows a pronounced
reduction on proximal recording in orthodromic nerve conduction studies. The sensory
Fig. 11.12: Measurement of duration of SNAP

a = onset to negative peak
b = onset to positive peak
c = onset to return to baseline
nerve action potential amplitude is also reduced in antidromic studies on proximal

stimulation of nerve compared to distal. In contrast to this, the sensory nerve action
potential amplitudes remain stable or there is minimal change on proximal stimulation in
motor nerve conduction studies.
H-Reflex
The H-reflex was described by Hoffman in 1918 and hence named as H-reflex. It is a
useful diagnostic measure for radiculopathy and peripheral neuropathy. The H-reflex is
a monosynaptic reflex elicited by submaximal stimulation of the tibial nerve and recorded
from the calf muscle. In normal adults, it can also be recorded in other muscles of the limbs
but not from the small muscles of hands and feet except in children below 2 years. H-reflex
can be enhanced by the maneuvers which increases motor neuron pool excitability such
as muscle contraction. H-reflex has the advantage of evaluating the proximal sensory
and motor pathways. It is therefore especially helpful in the evaluation of plexopathies
and radiculopathies. In Guillain Barre syndrome, H-reflex may be absent, delayed or
dispersed. In S1 radiculopathy, the soleus H-reflex may be absent. Similarly, flexor carpi
radialis H-reflex may be abnormal in C6C7 radiculopathy. H-reflex is influenced by
a number of spinal or supraspinal variables. The H-reflex studies, therefore, provides
useful information which are helpful in understanding the pathophysiology of various
central nervous system abnormalities.
F-Wave
The F-wave was first described by Magladary and McDougal in 1950 in small muscles
of the foot. The F-wave is a useful supplement to nerve conduction studies and
electromyographic measures and is most helpful in the diagnosis of conditions where
the most proximal portion of the axon is involved. It is elicited by the supramaximal
stimulus of a peripheral nerve at a distal site, leading to both orthodromic and
antidromic impulses. While the orthodromic impulse travels to the distal muscle, the
antidromic response travels to the anterior horn cell. The F-wave studies are valuable
in the conditions like Guillain Barre Syndrome, thoracic outlet syndrome, brachial
plexus injuries and radiculopathies.
Variables Affecting the Nerve Conduction Study

A number of physiological and technical variables can influence the results of nerve
conduction velocity. It is important to be aware of these factors and eliminate these as far
as possible for reliable and reproducible results.
Physiological Variables
Age: The nerve conduction velocity in a full term infant is nearly half of the adult
value. As the myelination progresses, the nerve conduction velocity attains the adult
value by 35 years of age. The conduction velocity begins to decline after 3040 years
of age but the values normally change by less than 10 m/s at the sixth or even in the
eight decades.
Upper versus lower limb: The median and ulnar nerve conduction velocity is higher
compared to tibial and pero neal. An inverse relationship between height and nerve
conduction velocity suggests that the longer nerves conduct slower than the shorter nerves.
These variables may also account for the faster conduction in the proximal nerves compared
to distal.
Temperature: Temperature significantly influences the conduction velocity and the
amplitude compound muscle action potential. Low temperature results in slowing of
nerve conduction velocity and increase the amplitude. For each degree Celsius fall in
temperature, the latency increases by 0.3 ms. This is attributed to the effect of cooling on
sodium channel. On increasing the temperature, the velocity increase by 5% degree from
29 38C. The laboratory temperature, therefore, should be maintained between 21 23C.
If skin temperature is below 34C, the limb should be warmed by infrared lamp, by warm
water immersion or making appropriate correction of the results.
Technical Variables
Stimulating system: Failure of the stimulating system may result in unexpectedly small
responses. The nerve may be stimulated submaximally or the applied current may not
reach the intended target. An important source of failure of stimulating system is shunting
of current between anode and cathode either by sweating or by the formation of a bridge
by conducting jelly.
Recording system: Faulty connection in the recording system may results in errors inspite
of optimal stimulation. The integrity of the recording system can be tested by asking the
patient to contract the muscle with the electrode in position. The MUPs are displayed on
the oscilloscope if the recording circuit is operational.
Inadvertent stimulation of unintended nerves: Spread of stimulating current to an
adjacent nerve or root not under study is frequent and failure to recognize, it results in
errors in latency measurement. Needle electrodes are helpful in recording from restricted
area of a muscle and are specially helpful in studying the innervation of individual motor
branches or pattern of anamolies.
Clinical Implications of Electromyography

The EMG is invaluable in diagnosing the characteristic changes in primary muscle
disorders and those following neurogenic disease. The EMG findings, however, like
any other investigation needs to be interpreted with the clinical picture presented by the
patient. The study of the disease can be classified under two major categories:
1. Neurogenic disorders
2. Myogenic disorders
Neurogenic disorders may include:
disorders of the peripheral nerves
polyneuropathies
motor neuron disorders
Myogenic disorders:
myopathies
inflammatory muscle disease
Neurogenic Disorders
1. Disorders of the peripheral nerves: The electromyographic findings are valuable in
the disorders of the peripheral nerves especially in cases of axonal degeneration. In the
disorders of the peripheral nerves the lesions are of three types:
a. Neuropraxia
b. Axonotmesis
c. Neurotmesis.
They may be due to traumatic injury or due to entrapment. These disorders typically
cause weakness and atrophy of the muscles innervated distal to the lesion.
Neuropraxia: Neuropraxia involves some form of local block which slows or stops
nerve conduction. Conduction above or below the block is usually normal. Bells
palsy, Saturday night palsy, carpal tunnel syndrome, etc. are the common causes of
conduction block. Nerve conduction measurement shows increased latency across the
blockage but normal above and below the blockage.
Axonotmesis: In axonotmesis, the neural tube is intact with axonal damage. On
electromyography testing there will be fibrillation potential and positive sharp waves in
two to three weeks following degeneration depending on the axon from the cell body.
Neurotmesis: In neurotmesis, there is disruption of neural tube along with axonal
damage. A nerve conduction velocity test cannot be performed because no evoked
response can be obtained. In electromyography spontaneous potential will appear
with the muscle at rest and no activity is produced with the attempted voluntary
contraction.
2. Polyneuropathies: In polyneuropathy, there is axonal damage or demyelination of
axons. Polyneuropathies typically results in sensory changes with distal weakness and
diminished reflexes. The common neuropathic conditions are:
a. Diabetic neuropathy
b. Alcoholic neuropathy
c. Neuropathy related with renal disease or carcinoma
d. Uraemic neuropathy
e. Nutritional neuropathies like Vitamin B12 deficiency neuropathy or Vitamin E
deficiency neuropathy
f. Neuropathy due to infections like leprosy or Guillain Barre syndrome
g. Toxic neuropathies.
With axonal damage, recruitment will be severely affected. Partial interference
pattern may be observed with maximal effort. The motor unit duration and amplitude
may be decreased. There are typical fibrillation potentials, positive sharp waves and
fasciculations.
3. Motor neuron disorders: Motor neuron disorders most commonly involve degenera-
tive diseases of the anterior horn cells. These include:
a. Poliomyelitis
b. Syringomyelia
Diseases that are characterized by degeneration of both upper and lower motor neuron
such as:
a. Amyotrophic lateral sclerosis
b. Progressive muscular atrophy
c. Progressive bulbar palsy
d. Spinal muscular atrophy.
Diseases of the anterior horn cell are classically indicated by fibrillation potentials and
positive sharp waves at rest. They also present by reduced recruitment with voluntary
contraction due to the loss of motor neurons. Polyphasic motor unit potentials of increased
amplitude and duration are often seen later in the course of motor neuron disease due to
reinnervation and collateral sprouting. This is a typical finding in post-polio paralysis and
amyotrophic lateral sclerosis where enlarged motor units are found in partially denervated
muscles.
Myogenic Disorders
The electromyographic findings provide information regarding the electrical activity of
muscle that supplements the clinical, biochemical and histological investigations in the
diagnosis of the muscle disease. The electromyography not only supplements the other
laboratory investigations of muscle disease but also provides information which cannot
be obtained by other means such as neuromuscular transmission abnormalities, myotonic
disorders and periodic paralysis. The common myogenic disorders are:
Inflammatory muscle diseases: Inflammatory muscle diseases include polymyositis,
dermatomyositis, inclusion body myositis, viral myositis and parasitic myositis.
The classical triad of EMG findings in Inflammatory muscle diseases includes:
1. Increased insertional activity with complex repetitive discharges
2. Fibrillations and positive sharp waves
3. Small polyphasic short duration motor unit potential recruited rapidly in relation to
the strength of contraction.
Muscular dystrophy: The common types of muscular dystrophies include Duchenne

muscular dystrophy, Becker muscular dystrophy, Facioscapulohumeral muscular
dystrophy, limb girdle muscular dystrophy, Oculopharyngeal muscular dystrophy and
myotonic dystrophy.
Myopathies: Congenital myopathies, metabolic myopathies, endocrine myopathies, etc.
In primary muscle disease such as the dystrophies or polymyositis, the motor unit
remains intact but degeneration of muscle fibres is evident. The typical findings are
a decrease in duration and amplitude of motor unit potential, full recruitment pattern
during full effort in spite of weakness and wasting. These changes may occur with or
without spontaneous electrical activity.
Glossary
Absolute refractory period: Brief time period (0.5 sec) after membrane depolarization during
which the membrane is incapable of depolarizing again.
Accommodation: When a constant current flows, the nerve adapts itself. This phenomenon is known
as accommodation.
Actinotherapy: Actinotherapy is the application of various radiations over the skin for therapeutic
purposes.
Active electrode: The smaller of the two electrodes under which greatest current density occurs or
the electrode that is used to drive ions into the tissues.
All-or-none response: The depolarization of nerve or muscle membrane is the same once a depolarizing
intensity threshold is reached; further increases in intensity do not increase the response. Stimuli at
intensities less than threshold do not create a depolarizing effect.
Alternating current: Current that periodically changes its polarity or direction of flow.
Ammeter: An ammeter is a low resistance galvanometer. It is used to measure the current in a circuit
in amperes.
Ampere circuital law: Amperes circuital law states that the line integral of magnetic field induction
around any closed path in vacuum is equal to 0 times the total current threading the closed path.
Ampere: Unit of measure that indicates the rate at which electrical current is flowing.
Amplifier: A device using electrical components to increase electrical power.
Amplitude: Describes the magnitude of the vibration in a wave. It is the maximum distance from
equilibrium that any particle reaches. It is also referred to as the intensity of current flow as indicated
by the height of the waveform from baseline.
Analgesia: Absence of pain or loss of sensibility of pain.
Anions: The ions which carry negative charge and moves toward the anode during electrolysis are
called anions. The ions formed when chemical reaction involves addition of electrons (i.e. reduction)
are called anions.
Anode: Positively charged electrode in a direct current system.
Arndt-Schultz principle: It states that no reaction or changes can occur in the body tissues if the
amount of energy absorbed is insufficient to stimulate the absorbing tissues. Addition of threshold
energy and above quantity of energy will stimulate the absorbing tissue to normal function and if
too great a quantity of energy is absorbed then added energy will prevent normal function or will
destroy tissue.
Atom: An atom is the smallest particle of an element. The diameter of the atom is of the order of
1010 m.
Attenuation: Attenuation is the term used to describe the gradual reduction in intensity of the
ultrasonic beam once it has left the treatment head.
Average current: The amount of current flowing per unit of time.
Axonotmesis: More severe compression injury may cause sufficient damage to the nerve axon.
Degeneration of the axon takes place including the myelin sheath. Once the nerve fiber has degenerated,
alteration in electrical reaction occurs.
Bandwidth: A specific frequency range in which the amplifier will pick-up signals produced by
electrical activity in the muscle.
Beat frequency: Beat frequency is produced as a result of interference of two currents.
Biofeedback: Biofeedback is the technique which is used to accurately measure, process and feedback
some reinforcing information via auditory or visual signals by electronic or electromechanical device
especially for therapeutic purposes.
Biot-Savarts law: Biot-Savarts law deals with the magnetic field induction at a point due to a small
current element. It states that the magnetic field induction at a point due to small current carrying
element depends upon the length of the conductor and current flowing through it and is inversely
proportional to the square of distance between the conductor and that point.
Bursitis: Inflammation of the bursa between bone and muscle tendon.
Capacitance: The capacitance of an object is the ability of the body to hold an electrical charge. Its
unit is Farad.
Capacitor electrodes: Air space plates or pad electrodes that create a stronger electrical field than a
magnetic field.
Cathode: Negatively charged electrode in a direct current system.
Cations: The ions which carry positive charge and move toward the cathode during electrolysis are
called cations. The ions formed when chemical reaction involves removal of electrons (i.e. oxidation)
are called cations.
Cavitation: This is the oscillatory activity of highly compressible bodies within the tissues such as
gas or vapor-filled voids. Cavitation may be stable or unstable cavitation.
Cell: Cell is a device by which chemical energy is converted into electrical energy. It is of two types
primary cell and secondary cell.
Chronaxie: The chronaxie is the duration of shortest impulse that will produce a response with a
current of double the rheobase.
Circuit: The path of current from a generating source through the various components back to the
generating source.
Clinical electromyography: Clinical electromyography is used for the study of diseases of muscles,
neuromuscular junctions and nerves. It is used for the purpose of electrodiagnosis.
Coaxial cable: Heavy well-insulated thick wire where centrally thick wire is surrounded by a
cylindrical mesh of thin wire.
Combination therapy: The application of two therapeutic modalities at the same time is described
as combination therapy. The most widely used combinations are those of ultrasonic with some form
of nerve and muscle stimulating currents.
Compound: A compound is a substance formed by the union of two or more elements via the
electrons of the atoms involved to form a molecule of the compound. Compounds may be either
electrovalent or covalent.
Conductance: The ease with which a current flows along a conducting medium.
Conduction: Heat loss or gain through direct contact.
Glossary 307
Conductors: Materials that permit the free movement of electrons.

Continuous wave ultrasound: The sound intensity remains constant throughout the treatment and
the ultrasound energy is being produced 100% of the time.
Continuous wave: An uninterrupted beam of laser light as opposed to pulsed wave.
Contraindication: The circumstance or the symptom which renders the use of a procedure inadvisable.
Contraplanar method: Contraplanar method is used in short wave diathermy for the deeper structures
of the body where through and through heating is required, e.g. hip, shoulder joint. The electrodes
are placed over the opposite aspects of the limb or joint, i.e. medial and lateral aspect or anterior or
posterior aspect.
Contrast bath: The principle of contrast bath therapy is to combine the effects of both hot as well as
cold baths together. It is most useful for treating various vascular disorders.
Convection: Heat loss or gain through the movement of water molecules across the skin.
Coplanar method: Coplanar method is used in short wave diathermy in which the two electrodes
are used in the same plane. This method is particularly suitable for the superficial structures and
spine.
Cosine Law: Cosine law states that the proportion of rays absorbed varies as per the cosine of the
angle between the incident and the normal. Thus, larger the angle at which the rays strike at the body
surface, lesser will be the absorption and vice versa.
Coulomb: Measurement indicating the number of electrons flowing in a current.
Coulombs law: According to Coulombs law, the force of interaction between any two point charges
is directly proportional to the product of charges and inversely proportional to the square of distance
between them.
Coupling media: As the ultrasonic waves cannot transmit through the air, some form of coupling
media is applied for the proper transmission of the waves. It should have the properties of high
transmissivity, high viscosity and hypoallergic nature, etc.
Crossfire method: Crossfire method is used in short wave diathermy. In this technique, half of the
treatment is given with the placement of electrodes in one direction, i.e. medial or lateral aspect and
another half is used with the placement of electrodes in other direction, i.e. anterior or posterior
aspect. This method is commonly used for the treatment of the knee joint, sinuses (frontal, maxillary
and ethmoidal) and for pelvic organs.
Current density: Amount of current flow per cubic area.
Current electricity: When charges flow through a conductor it is known as current electricity.
Current modulation: Current modulation refers to any alteration in the magnitude or any variation
in duration of the pulses. Modulation may be continuous, interrupted, burst, or ramped.
Current: The flow of charge in a conductor is known as electric current. Its unit is Ampere.
Decay time: The time required for a waveform to go from peak amplitude to 0 V.
Depolarization: Process or act of neutralizing the cell membranes resting potential.
Diathermy: The application of high-frequency electrical energy that is used to generate heat in body
tissues resulting from tissue resistance to the passage of energy.
Didynamic current: These are sinusoidal, direct currents being rectified mains type currents with
frequency of 50100 Hz.
Dielectric constant: The dielectric constants of the various tissues differ considerably. The tissues
of low impedance such as blood and muscles have higher dielectric constants. The tissues of high
impedance such as fibrous tissues and fat have low dielectric constant.
Differential amplifier: Monitors separate signals from the active electrodes and amplifies the
difference, thus eliminating extraneous noise.
Diode laser: A solid-state semiconductor used as a lasing medium.
Dipoles: Molecules whose ends carry opposite charges.
Eddy currents: Small circular electrical fields induced when a magnetic field is created that result in
intramolecular oscillation of tissue contents, causing heat generation.
Efferent: Conduction of a nerve impulse away from an organ.
Electric heating pads: Electric heating pads are used to provide raised temperature of 4045C to the
body parts. The main advantage of using electric heating pads is that they can be used at home by
the patients themselves and are cheaper and flexible, and are available in various sizes and shapes.
Electric shock: Electric shock is a painful stimulation of sensory nerves caused by sudden flow of
current, cessation or pause of flow of current or variation of the current passing through the body.
Electrical current: The net movement of electrons along a conducting medium.
Electrical field: The lines of force exerted on charged ions in the tissues by the electrodes that cause
charged particles to move from one pole to the other.
Electrical impedance: The opposition to electron flow in a conducting material.
Electrical potential: The difference between charged particles at a higher and lower potential.
Electricity: It is a form of energy which is produced due to electric charge. It is of two typesstatic
and current electricity.
Electrodes: These are the two conducting plates or pads which are used for the transmission of
current.
Electrolysis: The process of decomposition of electrolyte solution into ions on passing the current
through it is called electrolysis.
Electrolyte: The substance which decomposes into positive and negative ions on passing current
through it is called electrolyte. For example: acids, bases, salts, dissolved in water, alcohol, etc. are
common electrolytes. Pure salt like NaCl, KCl are electrolytes, in there molten state.
Electromagnetic spectrum: The range of frequencies and wavelengths associated with radiant
energy.
Electromyography: Electromyography is the study of the electrical activity of contracting muscle
which provides information concerning the structure and function of the motor units. It is a
technique by which the action potentials of contracting muscle fibers and motor units are recorded
and displayed.
Energy: Energy is the ability to do work. Its unit is Joule.
Excited state: State of an atom that occurs when outside energy causes it to contain more energy than
normal.
Faradic current: Faradic type current is short duration interrupted direct current with pulse duration
of 0.11 ms and frequencies between 50100 Hz, used for the stimulation of innervated muscles.
Fibrosis: Formation of fibrous tissue following injury.
Filter: Changes pulsating DC current to smooth DC.
Flemings right hand rule: According to this rule, if we stretch the first finger, central finger and
thumb of our right hand in mutually perpendicular directions such that first finger points along the
direction of the field and thumb is along the direction of motion of the conductor, then the central
finger would give us the direction of induced current.
Frequency: The number of cycles or pulses per second.
Glossary 309
Galvanic current: Galvanic currents are direct current which has a unidirectional flow of electrons
toward the positive pole.
Ground state: The normal unexcited state of an atom.
Ground: A wire that makes an electrical connection with the earth.
Hemarthrosis: Accumulation of blood in the joint cavity.
Heliotherapy: The use of sunlight for therapeutic purposes is known as Heliotherapy.
Hot packs: Hot packs provide superficial moist heat to the body parts. They contain the substance
which absorbs heat-like silica or gel. Applications of hot packs are most useful for relieving muscular
spasm and thus pain.
Hydrotherapy: Cryotherapy and thermotherapy techniques that use water as the medium for heat
transfer.
Impedance: The resistance of the tissue to the passage of electrical current.
Indication: The reason to prescribe a remedy or procedure.
Indifferent or dispensive electrode: Large electrode used to spread out electrical charge and
decrease current density at that electrode site.
Induction electrodes: Cable or drum electrodes that create a stronger magnetic field than electrical
field.
Infrared radiations: The infrared radiations are electromagnetic radiations with the wavelengths
of 750 to 400000 nm and frequency 4 1014 Hz to 7.5 1011 Hz. It lies beyond the red boundary of
visible spectrum.
Insertional activity: Insertional activity is seen in Electromyography which is due to mechanical
damage by the needle. Normally it produces a brief burst of electrical activity.
Insulators: Materials that resist current flow.
Intensity: A measure of the rate at which energy is being delivered per unit area.
Interferential therapy: Interferential therapy is the application of two medium frequency currents
to produce a low frequency effect. It is based on the principle of Interference, as a result of which a
beat frequency is produced.
Interpulse interval: The interruptions between individual pulses or group of pulses.
Interrupted direct current: Interruption is the most usual modification of direct current, the flow of
current commencing and ceasing at regular intervals.
Intrapulse interval: The period of time between individual pulses.
Inverse square law: The intensity of radiation striking a particular surface varies inversely with a
square of the distance from the radiating source.
Iontophoresis: Iontophoresis is a therapeutic technique, which involves the introduction of ions into
the body tissue through the patients skin. The basic principle is to place the ion under an electrode
with the same charge, i.e. negative ion placed under cathode and positive ion placed under anode.
Ions: The charged constituents of the electrolyte which are liberated on passing current are called
ions.
Kinesiological electromyography: Kinesiological electromyography is used in the study of muscle
activity and to establish the role of various muscles in specific activities. It is used to examine the
muscle function during the specific, purposeful tasks or therapeutic regimen.
Laser: The word LASER is an acronym for Light Amplification of Stimulated Emission of Radiation.
Law of Grothus-Drapper: It states that the rays must be absorbed to produce the effect and the
effects will be produced at that point at which the rays are absorbed.
Law of inverse square: Law of Inverse Square explains the effect of distance on the intensity of
infrared rays. It states that the intensity of a beam of rays from a point source is inversely proportional
to the square of the distance from the source.
Lenz law: This law gives us the direction of current in a circuit. According to this law, the induced
current will appear in such a direction that it opposes the change (in magnetic flux) responsible for
its production.
Lewis Hunting reaction/response: The alternate phases of vasoconstriction and vasodilatation leads
to hunting toward the mean point and is known as Lewis-hunting reaction.
Longitudinal wave: The primary waveform in which ultrasound energy travels in soft tissue, with
the molecular displacement along the direction in which the wave travels.
Macroshock: An electrical shock that can be felt and has a leakage of electrical current of greater
than 1 mA.
Magnetic field: When current is passed through a coiled cable that affects surrounding tissues by
inducing localized eddy currents within the tissues, then field created is called magnetic field.
Maxwell Cork screw rule: According to this rule, if we imagine a righthanded screw placed along
the current carrying linear conductor, be rotated such that the screw moves in a direction of flow
of current, then the direction of rotation of the thumb gives the direction of magnetic lines of force.
Medical galvanism: Creation of either an acidic or alkaline environment that may be of therapeutic
value.
Medium frequency currents: Medium frequency currents are the currents whose frequency falls
between the range of 1000 to 10000 Hz. They are being used therapeutically due to their advantage
of greater penetration and with a higher tolerance and comfort over the low frequency current.
Microshock: An electrical shock that is imperceptible because of a leakage of current of less than 1 mA.
Microwave diathermy: Microwave diathermy is the use of microwaves for therapeutic purposes.
The frequency and wavelength ranges from 300 MHz to 300 GHz and 1 cm to 1 m. The commonly
used frequencies are 2456 MHz, 915 MHz and 433.92 MHz with wavelengths of 12.24, 32.79 and 69
cm respectively.
Modified faradic current: For better result in the treatment faradic current is always surged to
produce a near-normal tetanic-like contraction and relaxation of muscle. This is called modified
faradic current. Various forms of surge are available, such as trapezoidal, triangular and saw-tooth.
Monochromaticity: When a light source produces a single color or wavelength.
Monophasic current: It is another name for direct current, in which the direction of current flow
remains the same.
Monopolar method: It is used in short wave diathermy in which only one electrode is placed over
the treatment area and other electrode is placed at a distance site or is not used at all. The electrode
used produces a radial electric field.
Motor nerve conduction velocity: The conduction velocity of a motor nerve is called motor nerve
conduction velocity.
Motor point: Motor point is that point where the nerve enters the muscle or impulses have maximum
contraction at that point. It is usually located at a point of upper one-third and lower two-thirds of
the length of muscle.
Motor unit action potential: The motor unit action potential is the sum of electrical potential of the
muscle fibers present in the single motor unit.
Mutual induction: Mutual induction is the property of two coils by virtue of which each opposes
any change in the strength of current flowing through the other by developing an induced emf.
Glossary 311
Myofascial pain: A type of referred pain associated with trigger points.

Nerve conduction velocity: Nerve conduction velocity is the speed with which a peripheral motor
or sensory conducts an impulse.
Neuropraxia: Temporary mild compression of the nerve which leads to the conduction block is
called neuropraxia.
Neurotmesis: Instead of minor compression if the injury is such as to disrupt all tissues of the
nerve fiber such as a cut through the nerve, then the distal segment degenerates completely. Such
lesion often requires surgery to ensure that the two cut ends are sufficiently approximated to allow
successful growth.
Ohms law: Ohms law states that the current flowing through a metallic conductor is directly
proportional to the potential difference across its ends and inversely proportional to the resistance,
provided that all physical conditions remain constant.
Pain gate theory: Pain gate theory states that the afferent inputs mainly passes through posterior
root of the spinal cord and all afferent information must pass through synapses in the substantia
gelatinosa and nucleus proprius of the posterior horn. It is at this level that the pain gate operates.
Paraffin wax bath therapy: Paraffin wax bath therapy is an application of molten paraffin wax on
the body parts. It provides more amount of heat than water because the mineral oil in the paraffin
lowers its melting point.
Phonophoresis: Phonophoresis is the movement of the drugs through skin into the subcutaneous
tissues under the influence of ultrasound waves.
Piezoelectric effect: The deformation of quartz or barium titanate or lead zirconate crystal occurs
due to the application of a varying potential difference. This is called piezoelectric effect.
Polarized state of nerve: In resting nerve, the nerve is positive outside and negative inside. At this
time, the nerve is not permeable to Na+ ions, so it is called as Polarized state of nerve. The change in
polarized stage causes the impulse to travel.
Potential: The electric potential of a body is the condition of that body when compared to the neutral
potential of the Earth. Its unit is Volt. It is directed form an area of low potential to an area of high
potential.
Power: It is the rate of doing work. The rate at which work is done by the source of EMF in main-
taining the current in electric circuit is called the electric power of the circuit. Its unit is Watt.
Pulse: The individual waveform as shown by an oscilloscope is referred to as a pulse.
Pulsed short wave diathermy: Pulsed short wave diathermy is referred to as pulsed electromagnetic
energy which is created by interrupting the output of continuous short wave diathermy at regular
intervals.
Pure faradic current: Pure faradic current was the type of current produced by the first faradic
coil and was unevenly alternating current with each cycle consisting of two unequal phases, low
intensity long duration and high intensity short duration current phase.
Radiation therapy: Radiation therapy is the application of various radiations over the skin for therapeutic
purposes. The various radiations used are infrared radiations and ultraviolet radiations, etc.
Rebox-type currents: Reboxtype currents are medium frequency currents derived from a device called
rebox. The current produced consists of unipolar rectangular pulses of between 50 and 250 s at 3000 Hz.
Recruitment pattern: In electromyography examination when voluntary contractions are initiated,
the motor units are recruited in an orderly fashion.
Resistance: It is the obstruction to the flow of electrons in a conductor. The unit of electrical resistance
is the Ohm.
Rheobase: The rheobase is the smallest current that produces a muscle contraction if the stimulus is
of infinite duration.
Rheostat: Rheostat is a device used to regulate current by altering either the resistance of the current
or potential in the part of the circuit. It consists of a coil of high resistance wire wound onto an
insulating block with each turn insulated from adjacent turns.
Russian currents: Russian currents are evenly alternating currents with a frequency of 2500 Hz
(between 200010,000 Hz). These are applied with a series of separate bursts, i.e. polyphasic AC
waveforms. There are thus 50 periods of 20 ms duration consisting of 10 ms burst and 10 ms interval.
Each 10 ms burst contains 25 cycles of alternating current, i.e. 50 phases of 0.2 ms duration. These
bursts reduces the total amount of current given to the patient thus increases patients tolerance.
Sauna bath: Sauna bath is the application of dry hot air in a wooden sauna chamber. The temperature
is kept between 6090C and relative humidity of the air is maintained between 510%.
Self-induction: Self-induction is the property of a coil by virtue of which, the coil opposes any
change in the strength of current flowing through it by inducing an emf in itself. Self-induction is
also called the inertia of electricity.
Sensory nerve conduction velocity: The conduction velocity of a sensory nerve is called sensory
nerve conduction velocity.
Shock: Shock is a stage of unconsciousness which could be due to so many causes.
Short wave diathermy: Short wave diathermy is the use of high frequency electromagnetic waves
of the frequency ranging between 107 to 108 Hz and a wavelength between 30 and 3 m to generate
heat in the body tissues. The therapeutically used frequencies and wavelengths are 27.12 MHz, 40.68
MHz, 13.56 MHz and 11 m, 7.5 m, 22 m respectively. It is the deepest form of heat available to the
Physiotherapist.
Sinusoidal currents: Sinusoidal currents are evenly alternating sine wave currents of 50 Hz. This
gives 100 pulses or phases in each second of 10 ms each, 50 in one direction and 50 in another.
Spontaneous activity: No spontaneous activity occurs in normal electromyography after a brief
burst of insertional activity.
Sprain: An injury of a ligament, partial or complete is known as sprain.
Static electricity: When the charges on the body do not flow, it is called static electricity. The simplest
way of producing a static electric charge is to rub two materials together.
Strain: An injury of a muscle or tendon, partial or complete is known as strain.
Strength-duration curve: Strength-duration curve shows the relationship between the magnitude of
the change of stimulus and the duration of the stimulus. The curve provides valuable information
regarding the state of excitability of a nerve.
Surging: For better result in the treatment, faradic current is always surged to produce a near-normal
tetanic-like contraction and relaxation of the muscle. The circuit is modified to give surges of various
durations, frequencies and waveforms. Surging is done to avoid accommodation of the current to
the nerve fibers.
Tendinitis: Inflammation of a tendon is called tendinitis.
TENS: Transcutaneous electrical nerve stimulation (TENS) is the application of low frequency
current in the form of pulsed rectangular currents through surface electrodes on the patients skin
to reduce pain.
Transducer: A device that changes energy from one form to another is known as transducer.
Transformer: A transformer is an electric device which is used for changing the AC voltages. A
transformer which increases the AC voltages is called a step-up transformer. A transformer which
decreases the AC voltages is called a step-down transformer.
Glossary 313
Trigger point: Any localized area of body when subjected to pressure causes pain in a specific area.
Tuning of the circuit: Tuning of the circuit is done in the application of short wave diathermy so as
to have maximum transfer of energy to the patients tissues.
Ultrasonic waves: Ultrasonic waves are the sound waves with a frequency well above the audible
sound waves of 2020,000 Hz.
Ultraviolet radiations: Ultraviolet radiations are the electromagnetic energy which falls between
visible rays and X-rays and have wavelength between 10 and 400 nm.
vant Hoffs law: vant Hoffs law states that any chemical change which is capable of being
accelerated is accelerated by the rise in temperature. Therefore, all the chemical changes of the body
that can be accelerated are accelerated by heat.
Voltameter: The vessel in which the electrolysis is carried, is called a voltameter. It contains two
electrodes and a solution electrolyte. It is also known as electrolytic cell.
Voltmeter: A voltmeter is a high resistance galvanometer. It is used to measure the potential
difference between two points of a circuit in volts.
Vasoconstriction: Decrease in the lumen (diameter) of the vessel.
Vasodilatation: Increase in the lumen (diameter) of the vessel.
Wallerian degeneration: Wallerian degeneration is a process by which the nerve degenerates
proximally to nearest node of Ranvier and distally throughout its whole length. Debris is cleared by
macrophagic activity. Process takes up to 21 days to complete and is a preparation for regeneration.
Water bag method: For the transmission of the ultrasound to the irregular patients tissue, water bag
method is applied.
Water bath method: When direct contact is not possible because of irregular shape of part or because
of tenderness, a water bath method may be used. As the part to be treated is immersed in water this
can only reasonably be applied to the hand, forearm, ankle and foot.
Whirlpool bath: Whirlpool bath is used therapeutically so as to combine the effects of temperature with
the mechanical effects of the water. These are used for various rheumatic disorders, postimmobilization
stiffness, joints pain, etc.
Suggested Reading
1. Barbara BJ, Susan ML. Physical Agents: Theory and Practice for the Physical Therapist Assistant.
FA Davis Company: Philadelphia, 1996.
2. Baxter D. Therapeutic Lasers: Theory and Practice. Churchill Livingstone, Edinburg, 1994.
3. Bonica J J. The Management of Pain. Lea Febiger: Malvern PA, 1990.
4. Braddom RL. Physical Medicine and Rehabilitation. Elsevier: India, 2008.
5. Chartered Society of Physiotherapy. Guidance for the clinical use of electrotherapy agent, 2006.
6. Dolphin S, Walker M. Healing Accelerated by Ionozone Therapy, Physiotherapy, 1979;65: 81-82.
7. Foster A, Palastanga N. Claytons Electrotherapy: Theory and Practice (9th edn). AITBS
Publishers: New Delhi, 2000.
8. Gersh MR. Electrotherapy in Rehabilitation. FA Davis: Philadelphia, 1992.
9. Johnson EW. Practical Electromyography (4th edn). Lippincot Williams & Wilkins, 2006.
10. Kahn J Principles and Practice of Electrotherapy (3rd edn). Churchill Livingstone: New York,
1994.
11. Khandpur RS. Handbook of Biomedical Instrumentation. Tata McGrawHill Publishing
Company Ltd: New Delhi, 1987.
12. Kitchen S, Bazin S. Claytons Electrotherapy (10th edn). PRISM, Indian edition.
13. Kitchen S. Electrotherapy: Evidence based Practice. Churchill Livingstone, Edinburg, 2002.
14. Kottke F. Handbook of Physical Medicine and Rehabilitation (3rd edn). WB Saunders:
Philadelphia, 1982.
15. Kovacs R. Electrotherapy and Light Therapy. Lea and Febiger: Philadelphia, 1949.
16. Krusen FH, Kotke FJ and Euwood PM. Handbook of Physical Medicine and Rehabilitation.
WB Saunders Company: Philadelphia, 1971.
17. Kuprian W. Physical Therapy for Sports (2nd edn). WB Saunders Company: Philadelphia, 1995.
18. Lehman GF and De Lateur BJ. Therapeutic Heat and Cold (3rd edn). Williams and Wilkins:
Baltimore, 1982.
19. Licht S. Electrodiagnosis and Electromyography (3rd edn). Elizabeth Licht: New Haven,
Waverly, 1971.
20. Low J and Reed Ann. Electrotherapy Explained: Principles and Practice, Butterworth Heinemann,
London, 1990.
21. Mannheimer J and Lampe G. Clinical Transcutaneous Electrical Nerve Stimulation. FA Davis:
Philadelphia, 1984.
22. Michloeitz SL. Thermal Agents in Rehabilitation. FA Davis: Philadelphia, 1990.
23. Mishra UK and Kalita J. Clinical Neurophysiology: Nerve conduction, Electromyography and
Evoked Potentials. BI Churchill: Livingstone, 1999.
24. Nelson R and Currier D. Clinical Electrotherapy. Appleton and Lange: Norwalk, Conn, 1991.
25. Newton RA. Electrotherapeutic Treatment. Preston Clinton, NJ, 1984.
26. Nikolova L. Treatment with Interferential Therapy. Churchill Livingstone: New York, 1987.
27. Ottawa Panel. Ottawa panel evidence-based clinical practice guidance for electrotherapy and
thermotherapy interventions in the management of rheumatoid arthritis in adults. Physical
Therapy, 2004;84(11):1016-1043.
28. Prentice WE. Therapeutic Modalities in Sports Medicine. Times Mirror Mosby College
Publishing: St. Louis, 1990.
29. Rennie. Diadynamic Current Therapy. In Current Physical Therapy (Peat M, Ed) Toronto: BC
Decker 1988.
30. Robertson V, Ward A and Low J. Electrotherapy explained: Principle and Practice, (4th edn)
Elsevier, Oxford 2006.
31. Robinson AJ and Madder LS. Clinical Electrophysiology (2nd edn). Williams and Wilkins:
Baltimore, 1994.
32. Savage B. Interferential Therapy. Faber and Faber: Boston, 1984.
33. Scott P. Claytons Electrotherapy and Actinotherapy (5th and 7th edns). Baltimore: Williams
and Wilkins, 1965 and 1975.
34. Shriber WA. Manual of Electrotherapy (4th edn). Lea and Febiger: Philadelphia, 1975.
35. Stillwell GK. Therapeutic Electricity and Ultraviolet Radiations. Sidney Licht (Ed) (3rd edn).
Williams and Wilkins: Baltimore, 1983.
36. Sullivan SB and Schmitz TJ. Physical Rehabilitation: Assessment and Treatment (4th edn). FA
Davis, 2001.
37. Sunderland S. Nerves and Nerve Injuries. Williams and Wilkins: Baltimore, 1968.
38. Wadsworth H and Chanmugan AP. Electrophysical Agents in Physiotherapy. Marrickville,
NSW, Australia, Science Press, 1983.
39. Walsh DM and McAdams ET. TENS: Clinical Applications and Related Theory. Churchill
Livingstone, New York, 1997.
40. Watkins AL. A Manual of Electrotherapy (3rd edn). Lea and Febiger: Philadelphia, 1968.
41. Watson T. The role of Electrotherapy in Contemporary Physiotherapy Practice. Manual Therapy
2000;5(3):132-141.
42. Wolf SL. Electrotherapy. Churchill Livingstone, New York, 1981.
Index
Page numbers followed by f refer to figure

A B
Abnormal spontaneous potentials 295 Bacterial infections 165
Absolute refractory period 305 Bandaging method 238
Absorption of exudates 139, 148, 208 Barbiturates 225
Acne vulgaris 214, 220 Basic
Actinotherapy 305 principles of interferential therapy 136
Acute properties of magnets 40
sepsis 261 Bicipital tendinitis 271
skin conditions 215 Biot-Savarts law 32, 33f, 34, 306
Adhesive capsulitis 178 Blood flow 260
Advantages of Bone
cable method 162 and articular cartilage 231
interferential currents 138 injuries 260
Alkali accumulator 29, 29f Brushing method 238
Alopecia 214, 224 Burns 166, 171, 260
Amperes circuital law 37, 305 Bursitis 306
Amplifier system 291 Burst
Analgesia 305 modulation 90
Ankle sprain 278 TENS 133
Anode 23, 305
Application of C
eddy currents 53
infrared Cable method 161
therapy 206 Capacitor
treatment 200 electrodes 306
short wave diathermy 181, 182 field method 154
superconductor 19 in parallel 11, 12f
Arndt-Schultz principle 199, 305 Carcinogenesis 212
Arterial disease 169 Cardiac disease 261
Asymmetric waveforms 88 Cathode 23, 306
Atomic mass 4 Causes of
Attenuation of ultrasound 249 earth
Axonotmesis 84, 302, 306 magnetism 47
shock 64 Crossfire
electric shock 62 method 307
heating effect of current 20 technique 161
Celiac rickets 223 for sinus 161f
Cell 25, 306 Crowding of magnetic lines of force 45f
Cervical spondylosis 175 Cryotherapy 273
Chronaxie 127, 306 Crystal laser 228
Chronic indurated edema 260 Current
Circulatory disorders 180, 204 carriers in
Clinical gases 13
electromyography 306 liquids 13
implications of electromyography 302 solid conductors 13
Coaxial cable 306 density 14, 307
Cold packs 274, 274f electricity 6, 12, 307
unit 275f modulation 89, 307
Combination therapy 264, 306 Cylindrical wavefront 69
Common motor points 119
Complete D
denervated muscle 126f
denervation 126 Daniel cell 25, 26f
rupture of ligament 189 De Quervains disease 270
Components of Deep X-ray or cobalt therapy 169, 172, 215
electromyography 289 Degenerative diseases 179, 204
ulcer 218 Deltoid inhibition 94, 111
ultrasonic apparatus 248f Depolarization 307
Concentration of electric field 166 Depth of penetration of rays 198
Conductors and non-conductors of electricity 5 Diathermy 151, 307
Constant galvanism 76 Didynamic current 307
Construction of Kromayers lamp 210 Different types of needles electrodes 290f
Continuous Diode laser 229, 308
modulation 89 Dipole moment 10
wave 307 Direct
ultrasound 307 contact method 254
Contraindications of short wave diathermy 168 monophasic current 78
Contraplanar pouring method 238
method 307 Direction of
positioning of electrodes 161 electric current 14
Contrast bath 242, 242f, 307 magnetic lines of force 36f, 44f
Coplanar Disadvantage of cable method 163
arrangement of electrodes 160f Discontinuous curves 8
method 181f, 307 Disorders of peripheral nerves 302
positioning of electrodes 160 Display system 292
Copper loss 58 Disturbed skin sensation 168
Correct size of electrodes 157f Dosage in chronic condition 257
Cosine law 200, 217, 307 Drug used in phonophoresis 262
Coulombs law 7, 33, 307 Dry cell 27, 27f
Index 319
Duration of motor unit action potential 294 induction 47

spectrum 61, 308
E waves 59, 59f
Electromotive force 13
Earth Electromyography 287, 308
circuit 64 Electrotherapeutic currents 76
shock 64 EMG recording system 293f
Eddy currents 52, 54, 308 Energy 308
on disc 52f density 230
on flat metallic plate 52f losses in transformer 58
on metallic plate with slots 53f source 228
Edison cell 29, 29f Erbs
Effects of paralysis 94, 106
frequency of stimulation 83 phenomenon 2
relative fields 162 Erythema 213
electric shock 63 Excess current 167
heat on Experimental verification of Lenzs law 50
muscular tissue 164 Explanation of Biot-Savarts law 33f
nervous tissues 164 Exponential current 88
sweat glands 164 Extracorporeal shockwave therapy 265
phonophoresis 262 Extrinsic semiconductors 17
Effects on
circulatory system and uses 276 F
inflammation 164
metabolism of body 163 Facial nerve stimulation 94, 108, 110f
muscle tissue 166 Factor influencing rate of regeneration 124
nervous system and neural tissues 276 Faradays
Electric experiments 47
current 12, 13 laws of
dipole 9, 9f electrolysis 23
heating pads 241, 308 electromagnetic induction 49
lines of forces 7, 8f second law of electrolysis 24
potential 12 Faradic
power 21 and IDC tests 127
shock 62, 167, 201, 308 current 92, 93, 308
Electrical foot bath 94, 116, 118f
current 308 type current 75
energy and power 20 Faradism under pressure 94, 115
stimulation of nerves 82 Fibrosis 308
Electrochemical equivalent 23 Fine-wire indwelling electrodes 290, 291f
Electrodes 23, 308 Finger photo transmission 281, 282
Electrolysis 23, 308 Flemings
Electrolyte 22, 23, 308 left hand rule 32, 32f
Electromagnetic right hand rule 51, 51f, 308
brakes 54 Fluorescent tubes 211
damping 53 Frequency of ultrasound 246
Frozen shoulder 178 Increasing blood supply 201

Induction
G electrodes 309
motor 54
Galvanic Infected ulcer 219
current 93, 309 Infectious diseases 179, 204
skin response 282 Inflammatory
Gas laser 228 diseases 179, 204
Gausss muscle diseases 303
law 45 Infrared radiations 196, 202, 309
theorem 45 Initiation of muscle action 90
Golfers elbow 236, 269 Insulators 22, 309
Grades of sprain 279 Intensity 251, 256, 309
Grid method 229 Interaction of laser with body tissues 230
Grothus law 217 Interference of light 70
Guillain Barre syndrome 301 Interferential therapy 136-138, 145, 148, 309
Interrupted
H direct current 76, 309
galvanic current 79, 92
Headache 202 modulation 89, 89f
Heating tissues 163 Inverse square law 217, 309
Heliotherapy 243, 309 Ions 23, 309
Helium-neon laser 228 Iontophoresis 128, 309
Hemarthrosis 309 Iron loss 58
Hemiplegia 285
Hemorrhage 261 K
High pressure mercury vapor
lamp 209 Kinesiological electromyography 288, 296, 309
tube 209f Kromayers lamp 210, 212
High TENS 131
Hip joint 183 L
Hot packs 240, 309
H-reflex 300 Laser therapy 226, 226f
Hydrocollator Latent heat 5
hot packs 240f Lateral
packs 240 collateral ligament injuries of knee 190
Hydrotherapy 309 epicondylitis 234, 268
Hypersensitive skin 167 ligament injuries of ankle 191
Hysteresis loss 58 popliteal nerve
injury 113
I stimulation 94
Law of
Ice conservation of energy 6
massage 273 Grothus-Drapper 200, 309
towels 273 inverse square 200, 310
Impaired blood flow 167 radiations 217
Index 321
reflection and refraction 67 Metabolic diseases 179, 204

refraction 67 Metatarsalgia 272
Lead-acid accumulator 28, 28f Methods of application 253f
Leakage of magnetic flux 58 Microcurrent electrical neuromuscular
Lechlanche cell 26, 27f stimulation 134
Lenzs law 50, 50f, 55, 310 Microshock 310
and energy conservation 51 Microwave diathermy 151, 169, 170f, 310
Lewis-Hunting reaction 276, 276f, 310 Modified
Ligament injuries 188 DC impulses 81f
Limitations of Ohms law 15 faradic current 76, 310
Long wave diathermy 151, 172 Molecular theory of magnetism 42
Longitudinal waves 70, 310 Monochromaticity 310
Lordosis and scoliosis of lumbar spine 184 Monophasic current 310
Lorentz force 37 Monopolar method 161, 310
Low Motor
backache 145, 179, 204 nerve conduction velocity 310
frequency currents 75, 90, 92 neuron disorders 303
TENS 131 point 310
Lowering skin resistance 97 starter 57
Lumbar stimulation 139
disk prolapse 184 unit action potential 310
spondylosis 182 Moving coil galvanometer 38, 38f
Luminous generators 197 Muscle
relaxation 201
M strengthening 285
Muscular dystrophy 304
Macroshock 310 Myoelectric signal 291
Magnetic Myofascial pain 311
dipole 45, 46f Myogenic disorders 303
field lines 46f
flux 47 N
line of force 43, 44f
Magnetized magnet 43f Natural magnet 40
Magnets and earth magnetism 40 Needle electrodes 289
Maintenance of paraffin wax bath unit 239 Neoplastic diseases 179, 204
Maxwells cork screw rule 37, 37f, 310 Nerve
Mechanism of conduction velocity 296, 311
injury 279 regeneration 124
pain gate control 130 transmission 79, 82f
Medial Nervous system 261
collateral ligament injuries of knee 188 Neuropraxia 83, 302, 311
epicondylitis 236, 269 of motor nerve 92
ligament injuries of ankle 192 Neurotmesis 84, 302, 311
Median nerve stimulation 94, 98, 100f Nickel-cobalt ferrite crystal 248
Medium frequency currents 135, 310 Non-Ohmic conductors 16
Menstruation 169, 172 Normal motor unit action potential 294
Normalization of EMG 296 warts 260

Normally innervated muscle 126f Polarized state of nerve 311
N-type semiconductor 18, 18f Postimmobilization stiffness 207
Nutritional rickets 223 Potential gradient 12
Power density 230
O Practical application of electrolysis 24
Precipitation of gangrene 168
Ohms law 1, 15, 16, 63, 311 Preparation of
Osteoarthritis of knee 185 apparatus 97
skin resistance lowering tray 96, 141
P treatment tray 95, 141
Pain Pressure sores 214, 221
gate Principles of
control 130 motor nerve conduction 297, 297f
theory 311 orthodromic sensory conduction 298f
relief 231 sensory nerve conduction 298
Paraffin wax bath Process of denervation 84
therapy 237, 311 Production of
unit 237 electric lines of forces 8
Parallel plate capacitor 10, 11f electromagnetic waves 60
Parameters of ultrasound 255 laser 227
Partial magnetic lines 43
denervation 126 microwave 170
rupture of ligament 189 ultrasound 248
Partially denervated muscle 127f ultraviolet radiations 209
Parts of typical paraffin wax bath unit 237 vitamin D 213
Pelvic inflammatory disease 194 waves 246
Penetration of phonophoretically driven drugs 262 Psoriasis 214, 221
Periarthritis shoulder 145, 177 P-type semiconductor 19f
Periodic waves 72 Pulse
Peripheral amplitude 86
nerve injuries 277, 285 charge 86
skin temperature 281, 282 frequency 88
vascular disease 277 Pulsed
Phenothiazine 225 mark 251
Phonophoresis 262, 311 short wave diathermy 169, 311
Physical principles of Pure faradic current 311
light 65 Purification of metals 24
sound 71 PUVA 222
Placement of apparatus 211
electrodes 178, 181
infrared lamp 206 Q
Plantar Quadriceps inhibition 94, 112
fasciitis 192, 236 Quantization of electric charge 6
Index 323
R action potential 298

conduction velocity 312
Radial Series rheostat 16
nerve stimulation 94, 104 Severed motor nerve 92
shock wave therapy 265 Severely ischemic tissue 261
Radiation therapy 196, 311 Severity of electric shock 63
Ramping modulation 90, 90f Shock 62, 312
Rapid information 285 wave therapy 265
Rebox-type currents 135, 311 apparatus 266f
Reducing healing time 166 Short wave diathermy 151, 151f, 183, 312
Reflection of ultrasound 251 Shunt rheostat 16
Regeneration of nerve 84 Single fibre needle electrodes 290
Relearning of muscle action 91 Sinusoidal currents 78, 312
Relief of pain 138, 165, 241 Size of electrodes 157
Removal of waste products 93 Skin
Renal rickets 223 and connective tissue 241
Repetitive discharges 296 conductance activity 281, 282
Replacing orthosis 92 grafting 215
Rheobase 127, 312 resistance lowering tray 95, 97f, 142f
Rheostat 16, 312 Smaller electrodes 158f
Rheumatoid arthritis 183 Snells law 67
Rickets 215, 223 Spacing of electrodes 158
Right hand Spherical
palm rule 34 capacitor 10, 11f
thumb rule 36, 36f wavefront 69
Ruby laser 228 Spinal cord injury 285
Russian currents 135, 135f, 312 Spontaneous activity 294, 312
Sprain of ligament 188
S Stable cavitation 259
Static
Sacroiliac strain 184 electricity 6, 312
Salpingitis 194 transformer 58
Sauna bath 243, 312 Stimulating system 301
Scanning Stimulation of
electrode 227f denervated muscle 92, 93
method 229 motor nerves 93
Scar tissue 260 sensory nerves 92
Scattering of light 68 Strength-duration curve 124, 312
Sciatica 184 Stress incontinence 149
Secondary Structure of atom 3
cell 28 Subacromial bursitis 272
osteoarthritis 186 Subdeltoid bursitis 271
Seddons classification 83 Sulphonamides 224
of injury 124 Superficial heating modalities 237
Semiconductor laser 229 Supraspinatus tendinitis 235, 270
Sensory nerve Surface electrodes 289f
T injury 102f
stimulation 101, 103f
Technique of EMG recording 293 Ultrasonic
Tendinitis 312 therapy 245
Tennis elbow 234, 268 waves 313
Tenosynovitis 270 Ultrasound
TENS 312 therapy 267
apparatus 130f treatment heads 246f
Tensile strength and scar tissue 230 Ultraviolet
Testing apparatus 251, 252 irradiations 213
Tetanic contraction 93 radiations 209, 216, 313
Tetracycline 224 Unmagnetized magnet 43f
Theraktin tunnel 211, 212 Uses of
Therapeutic uses of electromagnetic spectrum 62
cold therapy 276 shunt 39
laser 230 thermal effects 258
Thiazide diuretics 224 transformer 59
Thickening of epidermis 213 ultrasound 259
Transcutaneous electrical nerve stimulation 129
Transmission of V
heat 5
ultrasound 248 Vapocoolant sprays 274
Transverse waves 70 Variable
Treatment capacitor 10
of electric shock 63 transformer 58
tray 96f Varicose ulcers 260
Tuning of circuit 313 Vasoconstriction 313
Types of Vasodilatation 313
electric shock 63 Vasospastic disease 277
electricity 6 Venous
electrodes 156 thrombosis or thrombophlebitis 169
electromyography 288 ulcers 218
injury 124 Vitiligo 224
laser 228 Voltaic cell 25, 25f
rickets 223
semiconductors 17 W
TENS 131
transformers 58 Wallerian degeneration 84, 313
Water
U bag method 254, 255f, 313
bath method 254
Ulcers 218 Whirlpool bath 241, 242f, 313
Ulnar nerve Wound healing 230

Textbook of Electrotherapy 2nd Ed Jagmohan Singh

Uploaded by

Copyright:

Available Formats

Textbook of Electrotherapy 2nd Ed Jagmohan Singh

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Textbook of Electrotherapy 2nd Ed Jagmohan Singh

Uploaded by

Copyright:

Available Formats

Textbook of

Jagmohan Singh PhD

JAYPEE BROTHERS MEDICAL PUBLISHERS (P) LTD

Jaypee Brothers Medical Publishers (P) Ltd

2012, Jaypee Brothers Medical Publishers

Inquiries for bulk sales may be solicited at: jaypee@jaypeebrothers.com

I especially thank my colleagues Dr M Neethi, Dr Janarthanan Reddy, Dr Anu Sharma,

1. Basic Electricity, Light and Sound 1

Common Motor Points

Ligament Injuries 188

Golfers Elbow (Medial Epicondylitis)

10. Biofeedback 281

The Structure of an Atom

The Formation of Compounds

The Conductors and Non-conductors of Electricity

Other Methods of Producing Electricity

Quantization of Electric Charge

Electric Field Intensity due to a Group of Charges

Electric Lines of Forces

Properties of Electric Lines of Forces

Fig. 1.8: Tangents to two lines of Fig. 1.9: Electric dipole

Fig. 1.10: Paralllel plate capacitor Fig. 1.11: Spherical capacitor

Fig. 1.12: Capacitors in series

Fig. 1.13: Capacitors in parallel

The Current Carriers

Limitations of Ohms law

Fig. 1.15: Resistance in series

If R1, R2, R3 = resistance and V1, V2, V3 = potential difference,

Fig. 1.16: Resistance in parallel

I = V/R1 + V/R2 + V/R3

Fig. 1.17: N-type semiconductor

Fig. 1.18: P-type semiconductor

Thermal and Chemical Effects of Currents

Electrical Energy and Power

1 kWh = 1000 watt 60 60 sec

Chemical Effects of the Electric Current

Commonly used terms are:

Faradays Laws of Electrolysis

Generally ECE of a substance is expressed in gram/Coulomb (g/C). The value of ECE

The Primary Cells

Fig. 1.19: Voltaic cell

Fig. 1.20: Daniel cell

Fig. 1.21: Lechlanche cell

Fig. 1.22: Dry cell

The Secondary Cell

Fig. 1.23: Secondary cell (lead-acid accumulator)

Charging: Charging means storing of electrical energy. To charge this accumulator a

Fig. 1.24: Alkali accumulator or Edison cell

Magnetic effects of electric current

Fig. 1.25: Magnetic effects of electric current

Fig. 1.26: Effects on magnitude of force

Figs 1.27A and B: Flemings left hand rule

Let AB is a small element of length dl of the conductor XY which is carrying I. Let r

Fig. 1.28: Explanation of Biot-Savarts law

Fig. 1.31: Magnetic field due to a straight conductor carrying current

Fig. 1.32: Direction of magnetic lines of force

Fig. 1.33: Right hand thumb rule

Fig. 1.34: Maxwells cork screw rule

Moving coil Galvanometer

Fig. 1.35: Moving coil galvanometer