Bullet Maintenance Manual 01
Bullet Maintenance Manual 01
Bullet Maintenance Manual 01
TECHNICAL SPECIFICATION: -
Bullet 350CC
Engine Single Cylinder Four stroke with over-head Small - 63.03 / Large -
valve Main shaft ball bearings 62.05
Cubic Capacity 346 cc Final drive sprocket 16 teeth
Stroke 90 mm Rear drive chain 5/8" pitch chain
Bore-Nominal 70 mm Brake drum sprocket 38 teeth
Actual 69.875 mm / 2.751 in. Carburetor Mikcarb-VM-24
Compression Ratio 7.25 : 1 Main jet 90
Compression Pressure 110 +- 5 Psi (recommended) Pilot jet 25
Engine Output 18 BHP @ 5625 rpm Contact Breaker (Coil ignition)
Torque 2.74 kgm @ 2875 rpm Points gap 0.14/0.16" (0.35 to 0.4 mm)
Piston and Piston Rings Timing before TDC 1/32" (0.8mm)
14mm diameter B7HS
Ring Clearance in grooves (Dimensions for new components) Spark plug (NGK) or equivalent
Plain (2) .001/.003" Spark plug gap 0.46 to 0.50 mm
Scraper .002/.004" Condenser (Capacitor) 0.18 to 0.25 MFD
Ring end gap in bore .015/.020" Suspension
Maximum Ring Gap Telescopic hydraulic
Permissible 0.030" Front damping
Gudgeon pin diameter 0.7498/0.7500" Stroke 155 mm
Pivoted fork with shock
Crank Pin Diameter 1.24875 / 1.249 " Rear absorbers
Connecting rod small end
diameter 0.7505/.7507" Wheel Rim Type WM 2 - 19
Crankshaft Tyre Size 3.25 x 19 (Front)
Driving side ball bearing 25 x 62 x 17 mm (6305) Wheel bearings 3.50 x 19 (Rear)
25 x 62 x 17 mm (NU 305 or 17 x 40 x 12 mm (6203 or
Roller bearing N305) (Front & Rear) 6203 ZZ)
25 x 52 x 15 mm (NU 205 or NU Mechanical internally
Timing side roller bearing 205 R) Brakes expanding shoe type
178 mm x 38 mm Twin
Cam Lift 0.3125 in Front leading shoes
153 mm x 25 mm Single
Valve lift 0.3125 in Rear leading shoe
Valve timings with 0.012" clearance Fuel Tank
Exhaust opens 75 o BTDC Full Tank capacity 14.5 liters
Exhaust Closes 35 o ATDC Reserve capacity 1.25 liters
Inlet Opens 30 o BTDC Oil Capacity and Grades
Inlet Closes 60 o BTDC Oil Tank 2.25 liters SAE 20 W 50
200 ml on each leg
Rocker Bearings Inside 0.625 / .626" (Dimensions for new hydraulic oil or SAE- 10 W
diameters components) Fork 30
420 ml approximately SAE -
Rocker spindle diameter 0.6235 / 0.6240" Clutch 20 W 40
700 Grams of veedol 00
grease (For topping use
Inlet valve stem diameter .3425 / .3430" Gear box SAE - 20 W 50)
Bullet 500CC
Engine Single Cylinder Four stroke with over-head Small - 63.03/ Large -
valve Main shaft ball bearings 62.05
Cubic Capacity 499 cc Final drive sprocket 17 teeth
Stroke 90 mm Rear drive chain 5/8" pitch chain
Bore-Nominal 84 mm Brake drum sprocket 38 teeth
Actual 83.96 mm / 83.97 mm. Carburetor Mikcarb-VM-28
Compression Ratio 6.5 : 1 Main jet 110
Compression Pressure 110 +- 5 Psi (recommended) Pilot jet 25
Engine Output 22 BHP @ 5400 rpm Contact Breaker (Coil ignition)
Torque 3.5 kgm @ 3000 rpm Points gap 0.14/0.16" (0.35 to 0.4 mm)
Piston and Piston Rings Timing before TDC 1/32" (0.8mm)
Ring Clearance in grooves (Dimensions for new components) Spark plug NGK BR8 ES or equivalent
Plain (2) .001/.003" Spark plug gap 0.46 to 0.50 mm
Scraper .002/.004" Condenser (Capacitor) 0.18 to 0.25 MFD
Ring end gap in bore .015/.020" Suspension
Maximum Ring Gap Telescopic hydraulic
Permissible 0.039" Front damping
Gudgeon pin diameter 0.7498/0.7500" Stroke 155 mm
Pivoted fork with shock
Crank Pin Diameter 1.24875 / 1.249 " Rear absorbers
Connecting rod small end
diameter 0.7505/.7507" Wheel Rim Type WM 2 - 19
Crankshaft Tyre Size 3.25 x 19 (Front)
Driving side ball bearing 25 x 62 x 17 mm (6305) Wheel bearings 3.50 x 19 (Rear)
25 x 62 x 17 mm (NU 305 or 17 x 40 x 12 mm (6203 or
Roller bearing N305) (Front & Rear) 6203 ZZ)
25 x 52 x 15 mm (NU 205 or NU Mechanical internally
Timing side roller bearing 205 R) Brakes expanding shoe type
178 mm x 38 mm Twin
Cam Lift 0.3125 in Front leading shoes
153 mm x 25 mm Single
Valve lift 0.3125 in Rear leading shoe
Valve timings with 0.012" clearance Fuel Tank
Exhaust opens 75 o BTDC Full Tank capacity 14.5 liters
Exhaust Closes 35 o ATDC Reserve capacity 1.25 liters
Inlet Opens 30 o BTDC Oil Capacity and Grades
Inlet Closes 60 o BTDC Oil Tank 2.25 liters SAE 20 W 50
200 ml on each leg
Rocker Bearings Inside 0.625 / .626" (Dimensions for new hydraulic oil or SAE- 10 W
diameters components) Fork 30
420 ml approximately SAE -
Rocker spindle diameter 0.6235 / 0.6240" Clutch 20 W 40
DE – CARBONIZING: -
After a few thousand kilometers usage the carbon build up in the engine will cause general falling off in power,
accompanied by increased fuel consumption and starting trouble. De-carbonizing will normally be necessary every 8000
kilometers. This can be carried out without removing the engine from the frame. The mileage between de-carbonizing will
vary from machine to machine depending on the type of usage. A machine used for frequent short journeys will require
more attention that one that is used for long distance touring.
• Close the petrol tap. Disconnect the petrol hose from petrol tap end.
• Remove the two studs which holds the petrol tank to the frame and pull the petrol tank upwards.
Removal of Valves
To remove valves from the cylinder head, first lift off the end caps from the valve stems. If these have stuck they can be
removed with a screwdriver. Using compressing tool PED 2018 ST compress the valves springs from the valve tip.
Slacken back the compressing tools and release the springs. Withdraw the valve and place its springs, top spring collar,
bottom collar, the end cap and split conical collars together in order that they may be reassembled with the valve from
which they were removed. If the valve will not slide easily through the valve guide, remove any slight burrs on the end of
the valve stem with a carborundum stone or by using a fine jeweler's file to remove any sharp edge or burr. If the burrs
are not removed and the valve is forced out, the valve guide may be damaged.
Remove carbon from the valves, ports and combustion chamber by scraping. Take care not to cause any damage to the
valve faces or valve seat inserts. Scrape gently to avoid scoring the cylinder head. DO NOT, under any circumstances, use
caustic soda or potash for the removal of carbon from aluminium alloy. Remove the piston rings carefully. For cleaning the
grooves in the piston, a piece of broken piston ring thrust into a wooden handle and filed to a chisel point can be used.
If the piston rings are in good condition they can be put back, taking care to fit them in their original grooves and the same
way up. If the rings show brown or black patches, or if their gaps are more than specified service limits (Page 79), when in
position in the barrel, new rings should be fitted. The correct gap for new rings are given in the technical specifications
(pages 6 & 8 ) for 350 and 500cc. The gap should be measured in the least worn part of the cylinder, which will be found at
the top or bottom of the bore.
Examine the condition of the big end while the piston is removed. About 0.10" - 0.20" end float is permissible and it will be
possible to rock the connecting rod slightly. The big end has a floating bush with an original clearance of approximately .
003" However, if a DEFINIT E up and down play can be felt engine should be stripped further to have the big-end renewed.
Test the valve guides for wear by trying fit of a new valve in them. Both valves should be quite free, but the exhaust valve
has more clearance (.002") than inlet valve.
To remove the valve guides from the head, two special tools are required which can be easily made. The first is a piece of
tube with an internal bore of not less than 7/8". The second is a mandrel about 4" long made from 9/16" diameter bar with
the end turned down to 1/3" diameter for a length of 1/2". Support the cylinder head on the tube, which fits over the collar of
the valve guide. Using the mandrel, force the guide out of the head with a hand press or by using a hammer.
To fit a new guide, support the head at the correct angle and use a hand press and the same mandrel. If a hand press is
not available, the guide can be replaced using a hammer and a mandrel, to prevent damage to the guide. Check the length
of the valve springs which are originally 2.020" and 2.095" for the inner and outer springs respectively. If these have
reached the specified service limits they should be renewed.
Decompressor
Unscrew the adjusting screw and locknut from the cable block and pull the cable sideways out of the block. Push the spring
upwards and pull the cable nipple out of the body. It will now be possible to remove the cable and nipple through the spring,
leaving the decompressor body and spring detachedfrom the control cable.
The spring and the cap should now be replaced. The valve may be ground in by applying a thin coating of grinding paste on
the seat of the valve and twisting to and fro by means of the cable block at its upper end and occasionally lifting the valve
from its seat. Do not rotate the valve through a complete revolution before lifting, as this will groove the seat.
After grinding, wash the whole assembly thoroughly in petrol, opening and shutting the valve while doing so. Make sure that
all traces of grinding paste have been removed.
If the paste should get into the cylinder serious damage would be caused. If the valve shows a tendency to stick-up in the
body but otherwise is satisfactory, this can be cured by washing in petrol, though in this case it will not be necessary to
disconnect the control cable.
Before building up the engine, see that all parts are scrupulously clean and place them on a clean tray, work bench or over
a clean sheet of paper. While re-assembling it is advisable to fit a new gasket between the cylinder barrel and the
crankcase. Smear clean oil over the piston and space the ring gaps. The second ring is a taper ring and is marked TOP on
the upper surface.
WARNING : This mark should be on top when fitted. Reversing the ring will result in pumping of oil into the
cylinder and consequent smoking.
Place the piston over the connecting rod small end ensuring the split skirt is facing the front and insert the gudgeon pin.
Secure the gudgeon pin with the circlips. Oil the cylinder bore and gently push barrel over the piston while keeping the rings
compressed in their grooves and seat it gently on the barrel gasket. Refit the 1/4" nut above the timing chest. When fitting
the head again, apply jointing compound sparingly on both sides of the gasket. Replace the six nuts and tighten them
progressively and diagonally from one side to the other to prevent distortion.
Place the push rods with the adjustable parts downward. The shorter pushrod is the Inlet. Ensure valve stem caps are fixed
on the valve stems. Position the rockers and bearings, making sure that the oil feed holes are at the bottom and that the
The silencer could be cleaned of carbon using a hot caustic soda solution, if necessary.
NOTE: The cylinder head and base nuts should be checked again for tightness, after the engine has been run long
enough to get thoroughly warm.
Tighten clamp nuts on crankcase finally. For torque tightening of cylinder head nuts please refer torque chart on page .100
Remove the exhaust pipe and silencer. Remove ten screws from the timing cover, taking care not to lose the sealing
washers, one for each screw.
NOTE: When removing or refitting the timing cover it is important that the engine is gently cranked. This will prevent
damage of pump worm or the pump spindle.
Draw off the timing cover, tapping lightly if necessary with a wooden mallet.
While refitting the timing cover ensure that the joint washer is correctly located over the oil holes, using a little grease (not
compound) to hold it in position.
Ensure proper functioning of oil pump by checking oil flow at rocker pipe union when the engine is running at slow speed.
Slacken the oil pipe banjo union to see the oil flow and clamp it again properly. Wipe off the oil that has oozed out.
• Check the fit of the plungers in the pump discs, which should be sliding fit and should be able to be
moved in and out by hand.
NOTE : Replacement pump discs have a lip left at the opposite side of the lapped face. The purpose of this is
to hold the disc central in the housing during the lapping-in. It should be filed off before the pump is finally
assembled. Care should be taken not to damage the lapped face.
Wash all components and passages thoroughly with petrol after lapping, to remove all traces of grinding paste. Check
the pump disc springs for fatigue by assembling in the timing cover and placing the pump covers in position. The latter
should be held 1/8" off the timing cover if the springs are correct. The pump spindle should be renewed if excessive
wear has taken place on the teeth. Reassemble the oil pumps, replacing the cover gaskets. Before fitting each cover
fill the pump chamber with clean oil. Having assembled the pumps, lay the timing cover flat and fill the oil ports using
an oil can. Turn the pump spindle with a screwdriver in a clockwise direction and it can then be checked whether the
pumps are operating correctly. Before replacing the timing cover on the engine, fill the filter chamber with clean oil and
fit the filter element.
NOTE : With the engine running, the oil feed to the big end can be checked by partially unscrewing the feed
plug in the timing cover between the oil pumps. The oil return can be checked by slackening the rocker pipe
banjo bolt on the cylinder head and observing the oil flow.
Unscrew the pump worm using the hexagon head behind the worm, with special tool PED 2006. Withdraw the
timing pinion using a special tool PED 2013.
CAUTION: The worm nut has a left hand thread. When turned clockwise the worm nut can be loosened and
when turned anticlockwise the worm nut gets tightened.
Valve Timing
The cams are integral with the cam pinions. They have internal sintered iron bushes running on fixed spindles on the
timing chest.
The cams and the timing pinions are provided with timing marks to set proper valve timings. The procedure is detailed
below.
Bring the piston to the TDC position. Match the exhaust cam (provided with two sets of punch marks) with the timing
pinion so that the two punch marks coincide on both. Match the inlet cam to the exhaust cam so that the single punch
mark coincides on both. Push the cams home towards the crankcase.
It is very essential to ensure that the valves are closed fully during the closing period of the cam. The tappet clearance
should be adjusted properly to achieve this and to cater for a certain amount of thermal expansion of the working
components. We recommend 'NIL' clearance of the tappets to be set at cold. Provision for adjustment is given at the
bottom end of the push rod which sits over the tappet. Access to this is by removing the tappet cover.
Proceed as follows for adjustments. Bring piston to TDC at the end of compression stroke, so that both the valves are at
the closed position. This may be ensured by seeing the valve timing marks if the timing cover is open, or through
ammeter needle movement, when ignition is switched on. Check the push rods. They must rotate thumb free without any
up and down play.
In case the push rods do not rotate freely or if up and down play is noticed, the push rods need to be adjusted.
Loosen the lock nut in the adjuster, by holding the top nut. Thread in or out the bottom adjuster, till the correct push rod
freedom is achieved. Retighten the lock nut after adjustments are complete.
The 350cc clutch has five driven plates and four driving plates, including the friction disc on the sprocket.
The 500cc clutch is similar to that of 350cc, except that there are six driven plates and five driving plates.
Also the lugs on the clutch sprocket and the splines on clutch center are longer.
Remove the L.H. front foot rest, place a tray beneath the primary chain case to collect the oil in the chain case. Remove
the central nut in the chain case outer and remove the cover. To remove the clutch unscrew the clutch spring pins. Lift
away the spring caps, springs, clutch front plate, clutch pad in main shaft, the assembly of driving and driven clutch
plates and the clutch retaining spring. The clutch sprocket can then be withdrawn along with the chain and engine
sprockets (see point 10).
The clutch center can be removed only after the engine sprocket, primary chain and the clutch sprocket have been
removed.
To remove the clutch center hold the clutch with a brake bar (Special tool No PED 2025) and remove the center retaining
nut and washer with a box spanner. The clutch center can then be withdrawn from the shaft using extractor (Special Tool
No. PED 2005).
Remove the alternator stator by undoing three nuts. The primary chain is endless hence it is necessary to remove both the
engine and clutch sprockets simultaneously. Remove the central hexagon nut securing the alternator rotor, which can then
be drawn off, taking care not to lose the key. The engine sprocket is mounted on splines and can be removed along with
the clutch sprocket using extractor PED 2004 ST.
Remove the clutch as described above. Remove the primary chain tensioner. Remove the primary chaincase inner by
removing three nuts. Straighten the bent tab of the tab washer, which is provided for locking the final drive sprocket nut.
Hold the sprocket and remove the nut (right hand thread). The sprocket can then be withdrawn.
When re-assembling the clutch plates the following order must be observed. The clutch pad must be fitted into the main
drive shaft, plain dished plate (dish projecting outwards). Friction plate with inserts, plain flat plate, friction plate bonded,
plain dished plate (dish projecting inwards), friction plate bonded, clutch front plate, 3 springs on the clutch center lugs.
In the case of 500cc one more plain flat plate will also have to be fixed after the plate with inserts has been assembled.
The other three springs are located by means of bosses on the clutch cap. Tighten the spring pins as far as they will go. If
the clutch lifts un evenly it is probably is that one of the springs has taken a set in which case new springs should be fitted.
The friction plates with inserts should be renewed if badly worn or when the inserts have become loose in their plate. The
bonded friction plates require renewal when worn or charred. ( A light change to blackish color should not be mistaken as
charred). Excessive or premature wear of the platesis due to either running the vehicle at half clutch application or
depriving clutch plates of oil, with insufficient or no oil in the clutch chain case.
Access to the primary chain adjuster is gained by removing the primary chain cover, which is held in position by a single
nut. Before removing the nut, place a tray under the engine to collect the oil from the chaincase.
Beneath the bottom run of the chain is a curved slipper chain tensioner pad on which the chain rests. This can be raised or
lowered by turning the adjusting screw below the chain tensioner pad after having first slackened the locknut.
The chain should be adjusted so that there is 1/4" up and down movement at the center of the top run of the chain.
Remember to check the chain. Remember to check the chain tension at 3 or 4 places and then adjust accordingly. Ensure
that the chain tensioner pad moves freely and the lock nut of the adjuster is retightened after carrying out the adjustments.
The chain has to be changed if its length has increased by 3/4" more than the length of a new chain.
After replacing the chain cover remember to replenish the chaincase with oil (SAE 20) up to the level plug in outer chain
case (approx quantity 430 to 450 ml)
It is essential that there should be about 3 to 4mm free movement in the clutch cable to ensure that all the spring pressure
is exerted on the plates.
There are two points of adjustments on the clutch cable. The first is the midway adjuster at the middle of the cable just
above the chain case. The adjustment is made by screwing the adjuster screw in or out of the adjuster body. Tighten the
locknut on the screwed collar after adjustment has been made.
The other point is at the handlebar end. Loosen the locknut and thread in the adjuster to increase play and vice-versa to
reduce play. Tighten lock nut after carrying out adjustment. However, if the adjusters have reached their maximum position,
then the adjustment can be carried out in the gearbox outer cover. Before proceeding on the adjustment, turn in both cable
adjusters to their fully closed position (fully in position).
To make the adjustment, remove the inspection cover, slacken the locknut and turn the central screw in to get the desired
free play on the clutch lever at the handle bar end. Tighten.
Owing to initial bedding down of the clutch plate inserts, the clutch control may require adjustment after the first few
hundred kms with a new machine. This point should therefore be examined soon after delivery and adjustment made if
necessary. Initially, excessive play in the cable can be taken up through midway adjuster and the adjuster at the handle bar
end.
NOTE : The clutch adjuster ball and clutch rod may require cleaning and greasing around 6000 miles / 10000 kms
usage. To do this, loosen and carefully remove the clutch adjuster from its position, taking care not to drop it into
the gearbox outer cover.
Start the engine and tilt the motorcycle towards the gearbox side, so that the clutch rod can be removed. Wash thoroughly,
the clutch rod and adjuster and look for chipped or worn clutch rod ends and free rotation of the clutch adjuster ball.
The alternator consists of two parts, the stator and the rotor. The stator is mounted on to the primary chain case inner by
three studs and nuts.
The rotor, which contains the permanent magnet, is mounted on the end of the drive shaft and is located by a key and
secured by a special nut and spring washer. The designed radial air gap between the rotor and the poles of the stator is
0.25mm (0.010") and care must be taken when refitting to see that it is not less than 0.15mm (0.006") at any point.
Fit the rotor first, making sure that it is located concentrically on the end of the drive shaft. Attention must be given to the
proper seating of the key. Finally secure the rotor with the appropriate washer and nut.
Having fitted the rotor, the stator may then be fitted on to the chain case inner with the coil connections facing outwards.
Replace the shake proof washers and the nuts on the studs and tighten gently. Insert six strips (preferably non magnetic
material) 0.15mm (0.006") thick and 25.4mm (1") wide. Check whether the strips are free in position. If one or more of the
Function of Breather
The efficient operation of the breather is of paramount importance to the performance of the engine because it acts as a
non-return valve between the crankcase and the outside atmosphere, causing a partial vacuum in the crankcase and
rocker boxes which prevents the passage of oil into the cylinder. If the breather is not acting efficiently, it may cause
pressure in the crankcase instead of partial vacuum, giving rise to smoking or oiling of the plug.
Gear Box
The gears, ratchet mechanism etc. of the gearbox can also be serviced without dismantling the engine from the frame.
Remove the primary chain case outer, clutch assembly, stator and rotor, engine sprocket and clutch sprocket. Remove the
clutch centre and chain case inner.
Remove four 3/8" nuts and the gearbox can then be withdrawn from the engine.
Drain the oil tank by removing the feed and return filter assembly plugs located in the crankcase bottom.
Having removed the engine from the frame dismantle the cylinder head, barrel, piston, timing gear etc., as described in the
chapter "Decarbonising".
Remove the nuts on the driving side of the engine from four fixed studs at the rear of the crankcase.
Remove six studs passing through the crankcase by undoing nuts.
The driving side outer race of bearings will remain in the driving side half of the crankcase.
The driving side bearing inner race and the inner distance piece will remain on the engine shaft. ( Crankshaft)
The flywheel assembly may be removed from the driving side of the crankcase.
Clean the crankcase thoroughly as any trace of oil in the crankcase will burn and discolor the bearing race while heating the
crankcase.
Heat the crankcase in an oven or apply the naked flame of a blow lamp on the circumferential area of the bearing boss and
not directly on the bearing race. When the crankcase gets heated up fairly, about 110º-120ºC, tap the crankcase on a
wooden block (with the bearing race facing downwards) gently so that it will drop down due to the expansion of the bearing
boss.
Remove the circlip from the driving side crankcase and reheat to remove the ball bearing.
Inspect the bearings before assembly. The bearing should spin smoothly. Rotated dry, it may appear to be slightly noisy but
there should be no signs of corrosion, nor must there be any appreciable radial slackness. The outer race of the roller
bearing must be preferably smooth and bright with no evidence of crack or pitting. The individual rollers must show no signs
of wear and should rotate smoothly in the cage. It is recommended to replace with new bearings once they are removed
from the crankcase.
Reheat the crankcases to reassemble the bearings in the crankcase. Assemble the ball bearings in the D/S crankcase after
fitting the circlip. Locate the other circlip, distance tubes outer and inner and then assemble the roller bearing outer race.
Ensure that the bearings are seated properly in the crankcase and the outer roller race is flush with the crankcase.
When wear is noticed or step formation seen on the spindle, it should be replaced. To remove the cam spindle, heat the
crankcase and tap the spindles out from inside.
To remove the idler pinion spindles, heat the crankcases as before, hold the spindles in a vice and tap the crankcase lightly
with a nylon/wooden hammer.
To replace the cam spindles, locate the spindles in respective holes in the timing side crankcase and drive the spindles in
home with a small hammer (1/2 lb.) and a drift. Make sure that the spindles are upright and parallel to each other.
Connecting Rod
Wear in the hardened steel big end bush will be shown by a formation of a ridge round the centre of the bearing surface
corresponding with the oil groove in the white metal floating bush. If this wear is excessive, the connecting rod should be
replaced.
Excessive wear on the small end of the connecting rod can be easily seen. The Gudgeon Pin will show a rocking motion if
wear is excessive.
The flywheel assembly consists of the crankshaft and the connecting rod.
Using PED 2037 with a pair of steel bars (about 1" x 3/8" x 9" long) placed across between the flywheel disc, press out the
crankpin using a hand press.
The connecting rod can then be removed along with floating bush.
Turn the crankshaft over in the jig and repeat with other side if necessary.
To remove the timing shaft, remove the set screw from the shaft nut and unscrew the nut. Drive the shaft out with a
hammer and drift. To replace the timing side shaft, reverse the above process, making sure that the key is a good fit and
that the nut is tightened securely by means of a box spanner with a 12" tommy bar.
The driving shaft has no nut but is secured by tightening the sprocket nut after the assembly of the engine. It should be
pressed in with a hand press or a hammer and drift. If the latter is used, care must be taken not to damage the centre. It
has a collar which butts against the flywheel disc.
To reassemble the crankshaft, press the crankpin into the timing side flywheel, making sure that the oil hole is in the correct
position and the thrust washer is facing the right way, i.e. with Chamfer away from the flywheel.
Test the oil passages using an oil can to make sure that they are clear.
Assemble the connecting rod over the floating bush and smear with engine oil.
Place the other thrust washer over the crankpin, also with the Chamfer away from the flywheel.
Use a brass drift and hammer for pressing the D/S flywheel.
Locate the flywheel in the assembly jig, to ensure that the flywheels and shafts are in line, and replace the nuts. Tighten
securely and refit the set screws.
Test the oil passages again to ensure that they are clear.
If the same crankpin has been put back, it will be necessary to drill out the old grub screw in order to clean the oil passages
after which a new grub screw must be fitted.
Mount the crankshaft between the centers of a lathe or on a pair of vee block and true up to 0.001" on either side of the
shafts.
If the readings for the two shafts are high on opposite sides, the error can be corrected by gently tapping either or both of
the flywheels.
If the readings are high on the same side of the two shafts, it is probably due to dirt or foreign matter in the joints and the
crankshaft should be dismantled again, carefully examined and reassembled.
Replace the bearings, etc., in the crankcase halves after heating the crankcase as described earlier. (Refer page 29)
Fit the thrust washer on the drive shaft. Fit the bearing inner race on the drive shaft. Assemble the flywheel into the
bearing. If necessary use the sprocket nut with a suitable spacer to draw the driving shaft through the inner race of the
ball bearing.
Make sure that the crankcase face is clean and apply jointing compound to it and fix the crankcase gasket in position.
Put the thrust washer on the timing side shaft and press the bearing inner race.
Place the timing side crankcase in position over the flywheel and gently tap with wooden mallet.
Bolt the two halves of the crankcase together making sure that the joint matches correctly so that the cylinder base is flat.
Rotate the drive shaft by hand and check for free rotation to ensure correctness in assembly and press the oilseal on to
the drive side of the crankcase from outside, ensuring proper seating.
For 500cc
Press the oil seal onto the timing side of the crankcase and ensure proper seating.
Remove four screws and the gearbox outer cover can then be detached. Remove the foot control plate assembly and foot
control by taking off the two nuts securing it. Remove the mainshaft bearing cover which is attachedby two screws.
CAUTION: Hold the kickstarter return spring eyelet by means of a long screwdriver to prevent it from
rebounding (and causing damage) while the mainshaft bearing cover screw is removed.
The mainshaft can be drawn straight out. If the clutch has been removed which, however, should be done before taking off
the gear box inner cover, the top gear pinion and dog will come away with the mainshaft.
GEAR BOX: -
Dismantling the Gearbox
The gearbox can be completely dismantled with the engine in the frame except for the removal of the inside operator and
the bearings in the gearbox case. Remove the kickstarter crank, the gear change lever and the neutral finder. Remove the
top and bottom small inspection covers and disconnect the clutch cable, after loosening clutch adjuster.
Remove four screws and the gearbox outer cover can then be detached. Remove the foot control plate assembly and foot
control by taking off the two nuts securing it. Remove the mainshaft bearing cover which is attachedby two screws.
CAUTION: Hold the kickstarter return spring eyelet by means of a long screwdriver to prevent it from
rebounding (and causing damage) while the mainshaft bearing cover screw is removed.
The mainshaft can be drawn straight out. If the clutch has been removed which,
however, should be done before taking off the gear box inner cover, the top
gear pinion and dog will come away with the mainshaft.
The main shaft ball bearings can be removed by using a stepped drift of 0.437"(11mm) & 1.171"(29.77mm) in diameter for
the bearing in the case and 0.812"(20.64 mm) & 0.515" (13.1 mm) in diameter for the bearing in the cover.
When refitting the bearing stepped drifts of 2.31" (58.7 mm) & 1.171" (29.7 mm) diameter and 1" (25.4 mm) in diameter,
must be used for bearings in the case and cover respectively.
If the two pins securing the gear change ratchet mechanism are slackened, the adjuster plate can be set in the desired
position. In this position the movement of the gear lever, necessary to engage the ratchet teeth, will be approximately the
same in each direction.
When fitting new parts, if it is found that the gears do not engage properly, ascertain whether a little more movement is
required or whether there is too much movement so that the gear slips right through second or third gear into neutral. If
more movement is required, even after adjusting the adjuster plate then this can be obtained by filing the foot control stop
plate very slightly at the points of contact with the pegs on the ratchet ring. If too much movement is already present, a new
foot control stop plate giving less movement must be fitted.
The procedure for dismantling the gearbox with Continental controls is the same as described earlier.
While dismantling the gear change mechanism care should be taken to disconnect the foot control lever from the gear shift
shaft after loosening the hex bolt.
The circlip provided on the gear shift shaft should also be removed prior to removing the inner cover.
Grease nipples are provided on the shift shaft and gear lever on the left side of the motorcycle for periodical greasing to
ensure smooth operation of shift shaft and gear lever.
If excessive gear lever travel is noticed and gear engagement becomes difficult, the plastic bushes provided at the gear
linkages are worn out and will have to be replaced with new bushes to reduce play in the linkages.
The neutral finder is adjusted by means of an eccentric stopper secured to the front of the gearbox cover by a bolt which
limits the travel of the operating pedal. Slacken the bolt and turn the eccentric stopper until the correct movement of the
pedal is obtained.
Current machines have the gearbox filler plug at the top of the box and a level plug at the rear. Remove both plugs and fill,
with the machine on level ground until the oil commences to flow from the level plug.
Check the level every 800 to 1600 km when the gearbox is warm. For initial filling up of gearbox VEEDOL 'OO' grease is
recommended. During routine maintenance, topping up may be done with SAE 50 oil. The capacity is 700 grams (approx.)
of 'OO' grease mixed with SAE 50 grade oil to a thick consistency.
L U B RICATION: -
Lubrication system is by Dry Sump and effected by an automatic and positive double action oil pumps.
The oil tank is integral with the crankcase, for ensuring the full rate of oil circulation immediately when the engine is started
and for rapid heating of the oil in cold weather. The capacity of the oil sump is 2.25 Ltrs. (SAE 50 grade). There are two
piston type oil pumps running at 1/12 of engine speed positively driven by the worm gear on the timing shaft.
The feed pump is at the rear of the timing cover (Left side when viewed from the front) and pumps oil from the oil tank,
through the oil filter to the big end through the timing shaft. After lubrication of the big end bearings, the oil splashes and
lubricates the cylinder barrel walls and drains to the bottom of thecrankcase.
The return pump (front sied of the timing cover) draws the oil from the crankcase through the drilled passaage and passes
through the rocker oil pipe and lubricates the rocker bearings and valve spring mechanism and flows down through the
push rod tunnels into the timing cover chest.
From here, the drained oil is pumped back to the oil tank through a hole (drilled in the RH crankcase) by the two idler
pinions. The return pump has a capacity of approximately double that of the feed pump, which ensures that oil does not
accumulate in the crankcase. If allowed to accumulate it will lead to smoke – oil splash through breather pipe and starvation
of oil to rocker arm bearings.
Both pumps are double acting, but two sides of feed pump are inter-connected, thereby giving an augmented and even
supply to the big end. Return pump is also inter-connected for effective scavenging from crankcase.
Gauze strainers are provided for both feed and return filters from the crankcase to ensure oil is free from dirt and sludge.
Oil Filter: The oil filter has a special and important feature in design. In the case of clogged filter or should it be neglected
the oil pressure will lift the spring and cap off of its seat, thereby automatically by-passing the filter so that the big end
bearings will not be deprived of lubrication, even though the oil may be dirty.
Position 1: The plunger A is drawn out of the feed pump disc C, by the peg B in the spindle D, due to its rotation.
The suction port T in the pump disc aligns with the suction port Y in the timing cover and oil from the tank is drawn into
the pump disc as the plunger is drawn out
Simultaneously, the through hole W in the disc registers with the delivery port in the timing cover.
The outward movement of the plunger forces the accumulated oil in the annular space in the timing cover to be delivered
to the big end bearings through the oil filter element.
FE ED PUMP
T – Suction port
R – Delivery port
W, Z – Through holes
Position 2 : As the pump spindle rotates further the plunger A is pushed into the pump disc C.
The delivery port R in the pump disc registers with the delivery port X in the timing cover. The oil in the pump disc is
forced out through these ports, by the plunger for supply to the oil filter element and to the big ends.
Simultaneously the through hole Z, in the pump disc registers with the suction port Y in the timing cover and draws oil
from the tank, into the annular space in the timing cover, due to inward movement of the plunger into the disc.
Position 1:- The plunger A' is drawn out of the return pump disc C' by the peg B on the spindle D, due to its rotation.
The suction port T' in the pump disc registers with the suction port Y in the timing cover and oil from the crank case is
drawn into the pump disc as the plunger is drawn out.
Simultaneously, the through hole W' in the disc registers with the delivery port X in the timing cover.
The movement of the plunger forces the accumulated oil in the annular space in the timing cover to be delivered to the
cylinder head.
RE TU R N PUMP
Position 2 :- As the pump spindle rotates further the plunger A' is pushed into the pump disc C'.
The delivery port R' in the pump disc registers with the delivery port X' in the timing cover. The oil in the pump disc is
forced out through these ports, by the plunger, for supply to the cylinder head.
Simultaneously, the through hole Z' in the pump disc registers with the suction port Y' in the timing cover and draws oil
from the crank case chamber into the annular space in the timing cover due to inward movement of the plunger into the
disc.
Description of Frame
The frame is built of special cold drawn welded steel tubing incorporating reinforcements wherever necessary, for extra
strength.
Remove the top pivot pin nut, drive out the pivot pin, then hinge the suspension unit back on the lower pivot pin. After
removing the lower nut, the unit may be pushed off the pivot pin welded to the fork end. It is a sealed unit and the internal
mechanism cannot be serviced. Outer dust cover can be removed using special tool PED-2039 for cleaning coil spring.
Remove the rear wheel, chain, rear sprocket and brake cover plate assembly from the swinging arm chain stay. Remove
one of the pivot nuts and pull the pivot pin from the other end. The chainstay can then be pulled out of the frame.
The life of the rubber bonded silent-bloc bushes is very high. But if it is necessary to replace the bushes, the inner sleeves
will have to be pressed out first on a press. The rubber can than be taken away from the outer sleeves by pliers. The outer
sleeves can be driven out by means of a hammer and a suitable drift.
Replace the rubber bonded bushes in the swinging arm, using a suitable drift, press one bush from one end of the pivot
bearing tube under a press, until the metal outer sleeve is flush with the end face of the pivot bearing tube. While pressing,
it must be ensured that pressure is exerted only on the outer sleeve and not on the inner sleeve of the bush, as axial
pressure on the inner sleeve would destroy the bonding of the rubber to the metal sleeves. Similarly press the second bush
from the other side of the pivot bearing tube until the metal outer sleeve is flush with its end face.
While assembling the swinging arm fitted with rubber bonded silent-bloc bushes to the frame, the pivot nuts should be fully
tightened only with the swinging arm positioned in the mid-stroke of the spring boxes, i.e., when the centre distance
between the spring box top mounting hole in the frame and the bottom mounting pin on the swinging arm is 9.75". This is
recommended so that the rubber bush will be subjected to minimum angular movement in either direction from the mid
stroke.
To remove the centre stand take out the split pins & washers from both the ends of the stand spindle. Drift out the spindle
and withdraw the stand complete after disconnecting both the ends of the stand springs.
Description
The telescopic fork consists of two legs each of which comprises a main tube of alloy steel tubing which is screwed into the
casquette fork head at the upper end and securely clamped to the fork crown. Fitted over the lower end of the main tube is
the bottom tube made of high strength aluminum alloy with an integral lug which carries the wheel spindle. Fitted on the
lower end of the main tube is a steel bush which is a close fit in the bore of the bottom tube. The upper end of the bottom
tube carries a cast iron bush which is a close fit over the outside diameter of the main tube. These bushes are not fitted to
the latest Front fork Assemblies. The bush is secured to the bottom tube by means of a threaded housing which contains
two oil seals. A stud known as the 'Spring Stud' is fitted in the lower end of the bottom tube and a valve port is secured to
the lower end of the main tube. As the fork operates, oil is forced between the spring stud and the bore of the valve port
forming a hydraulic damping system. A compression spring is fitted inside the main tube between the upper end of the main
tube. The lower end of the main tube and the upper end of the bottom tube are protected by a cover secured to the fork
crown.
The fork provides a range of movement of 150mm/ 6" from the fully extended to the fully compressed position. The
movement is controlled by the compression spring and by the hydraulic damping system. The hydraulic damping is light on
the bump stroke and heavier on the rebound stroke, thus damping out any tendency to pitching or oscillation without
interfering unduly with the free movement of the fork when the wheel encounters an obstacle or pot hole.
The fork is filled with a light oil (S.A.E 30) to a point above the lower end of the spring so that the damper chamber 'B' is
always kept full of oil. Upward movement of the wheel spindle forces oil from the lower chamber 'A' through the annular
space between the spring stud and the bore of the main tube valve port into the damper chamber 'B'. During this stroke the
pressure on the underside of the valve plate causes it to lift so that oil can also pass from 'A' to 'B' through the eight holes
in the valve body. Since, however, the diameter of chamber 'B' is less than that of chamber 'A' there is no room in 'B' to
receive all the oil which must be displaced from 'A' as the fork operates. The surplus oil passes through the cross hole in
the spring stud and up the centre hole in the stud, spilling out through the nut which secures the upper end of the spring
stud to the lower end of the fork spring.
On the stroke, the oil in the damper rebound chamber 'B' is forced through the annular space between the spring stud and
the bore of the main tube valve port. During this stroke pressure in chamber 'B' closes the two disc valves at the upper and
lower ends of the chamber so that the only path through which the oil can escape is the annular space between the spring
stud and the port. Damping on the rebound stroke is therefore heavier than on the compression stroke. At the extreme end
of either pump or rebound stroke a small taper portion on the spring stud enters the bore of the valve port, thus restricting
the annular space and increasing the amount of damping . At the extreme end of the bump stroke, the larger diameter taper
on the oil control collar enters the main counter bore of the valve port thus forming a hydraulic cushion to prevent metal to
metal contact.
Place the machine on the centre stand, disconnect the front brake control cable & speedometer connection and remove the
front wheel and mudguard complete with stays. Unscrew the bottom spring and the stud nut which will allow oil to run out of
the fork down to the level of the cross hole in the spring stud.
Now knock the spring stud upwards into the fork with a soft mallet, thus allowing the remainder of the oil to escape. Pull the
fork bottom tube down as far as possible, thus exposing the oil seal housing. In the latest version the oil seal housing is
eliminated and the oil seals are provided as an integral part of the bottom tubes. Hence by pulling the bottom tube
downwards it can be removed from the fork main tubes. [For old type front forks: Unscrew this housing by means of a
spanner on the flats with which it is provided. The bottom tube can now be withdrawn completely from the main tube leaving
the bottom tube bush, oil seal housing and oil seal in position on the main tube.
Now unscrew the main tube valve port using special tool PED 2026.The spring stud and spring can now be withdrawn from
the lower end of the main tube.
NOTE : In the latest version the oil seal housing and steel bush has been eliminated on introduction of integral oil
seals in the bottom tubes.
The steel main tube bush can now be tapped off the lower end of the tube, if necessary using the bottom tube bush for this
purpose. Before doing this, however, it is advisable to mark the position of the bush with a pencil so as to ensure re-
assembling it in the same position on the main tube. The reason for this is that these bushes are ground to size, after fitting
on to the tubes, so as to ensure concentricity. After removal of the main tube bush, bottom tube bush and oil seal housing,
Spring
The free length of the spring is 20 1/2". The spring should be replaced if it has closed by more than 1 inch.
Re-assembly
When refitting the oil seal, or fitting a new one, great care must be exercised not to damage the synthetic rubber lip which
forms the actual seal.
NOTE : Only for Old Type Forks): If the oil seal housing has been removed from the upper end of the main tube and
is refitted from this end, a special nose piece must be fitted over the threaded end of the tube to prevent damage to
the oil seal.
The spring stud is a tight fit in the hole at the lower end of the bottom tube. Once the stud has been located in the hole,
push the bottom tube up sharply against the spring until two or three threads on the stud project beneath the end of the
bottom tube. Now fit the nut and washer and pull the stud into position by tightening the nut. If necessary fit the nut first
without the washer until sufficient thread is projecting to enable the washer to be fitted.
The fork complete with the front wheel and mudguard can be removed from the machine, if necessary, by adopting the
following procedure. The leads to the lighting switch and ammeter should be disconnected at their lower ends or by means
of the plug and socket connectors where these are provided.
Remove the two plug screws and loosen the steering head clip bolt and the fork crown clamp bolts.
Unscrew the fork main tubes from the headlamp casing and the steering stem locknut from the top of the steering stem,
turning each tube and the nut a turn or two at a time. When the nut has been removed from the steering stem and the main
tubes have been completely unscrewed from the headlamp casing, the complete fork and wheel with the steering stem can
be removed.
Lubrication
The lubrication of the fork internal parts is effected by the oil which forms the hydraulic damping medium. All that is
necessary is to keep sufficient oil in the fork to ensure that the top end of the bottom spring stud is never uncovered even in
the full rebound position. The level of oil in the fork can be gauged by removing the top plug screw and inserting a long rod
about 3/8" in diameter. If slightly tilted this will wedge against the nut at the upper end of the bottom spring stud. If the oil is
above the spring stud, it will leave a trace on the long rod, which can be seen on removal. This trace of oil implies that oil
level is correct. If the fork is empty to start with, the quantity required is 200ml in each leg. Recommended grade of oil is
hydraulic oil or SAE 10 W 30.
The steering head races and stand pivot bearing should be well greased on assembly. No nipples are provided for the
steering head as experience has shown that the provision of nipples at this point causes trouble through chafing and
cutting of control and lighting cables. If the steering head bearings are well packed with grease initially they will last for
several years or many thousands of kilometers.
WHEEL S : -
To remove the front wheel from the fork place the machine on the centre stand with sufficient packing beneath the
stand to lift the front wheel clear off the ground when the vehicle is tilted back. Slacken the brake cable adjustment
and disconnect the cable from the handlebar lever and from the operating cam lever on the hub.
Disconnect speedometer driving cable. Unscrew the four nuts securing the fork lug caps and allow the wheel to drop
forward out of the front fork. Make sure that the machine stands securely on the rear wheel and centre stand. If
necessary, place a weight on the dual seat or a strut beneath the front end of engine near frame down tube to ensure
this.
Dismantling
Lock the brake 'on', by applying the front brake and unscrew the cover plate nut. (For front brake with twin leading
shoes loosen the lock nuts on the link rod and turn link rod so that both brake shoes become free and are not in
contact with the brake drum). The cover plate assembly can then be withdrawn from the brake drum.
The brake shoes can be removed after detaching the return springs. Brake linings are supplied in pairs and are of
'Bonded' type hence linings cannot be separated and re-fixed with new linings.
To remove the operating cam unscrew the nut, which secures the operating lever to the splines on the cam. A sharp
tap on the end of the cam spindle will now free the lever, after which the cam can be withdrawn from its housing. The
brake shoe pivot pin can be removed after unscrewing the nut which secures it to the cover plate.
To remove the hub spindle and bearings, having first removed the brake cover plate, unscrew the retaining nut by
holding the spindle on a bench vice with soft jaws. Remove speedo drive assembly and the felt washer from the other
side of the hub. Remove the felt washer and the distance washer from the brake drum side and hit one end of the
spindle with a brass or plastic mallet, thus driving it out of the hub, bringing one bearing with it and leaving the other in
position in the hub. Drive the bearing off the spindle and insert the latter once more in the hub through the end from
which it was removed. Now drive the spindle through the hub, the other way, which will bring out the other bearing.
The fit of the bearings in the hub barrel is important. The bearings are locked on the spindle between shoulders and
the distance pieces , which in turn are held by the nuts on the spindle. In order to prevent endways pre-loading of the
bearings, it is essential that there is a small clearance between the inner edge of the outer race of the bearing and the
back of the races in either end of the barrel. To prevent any possibility of sideways movement of the hub barrel on the
bearing, it is therefore necessary for the bearings to be a tight fit in the barrel, but this fit must not be so tight as to
close down the outer race of the bearing and thus overload the ball race in the bearing.
1. Front Wheel rim (WM 2-19) 14. Front brake shoe c/w lining S/L
2. Front Wheel spokes (outer) 15. Front brake shoe spring (7" dia.)
16. Front brake cover plate (7" dia.)
3. Front Wheel spoke nipples S/L
17. Front brake show pin (7" dia.)
4. Front hub assembly (7" dia.) S/L
5. Front hub journal bearing (SKF 6203) 18. Washer front brake shoe pin S/L
6. Front hub spindle 19. Nut front brake shoe pin S/L
20. Front brake operating cam (7"
7. Front hub felt retainer dia.) S/L
8. Front hub felt washer (drum side) 21. Nut front hub cover plate
22. Front hub spindle nut (speedo
9. Front hub cover plate distance collar side)
23. Front brake operating cam lever
10. Front hub felt washer (speedo side) (7" dia.) (S/L)
11. Front hub felt washer retainer (speedo 24. Washer front brake operating
side) cam lever (S/L)
25. Nut front brake operating cam
12. Front hub speedo drive spacing collar lever S/L
13. Speedo drive complete
Re-assembly
To refit the bearings in the hub, two hollow drifts (Special Tool No. PED 2011) are required. One bearing is first fitted
to one end of the spindle by means of the hollow drift. The spindle and bearing are then inserted into one end of the
hub barrel, which is then supported on one of the hollow drifts. The other bearing is then inserted over the upper end
of the spindle and driven home by means of the second hollow drift either under a press or by means of a hammer,
which will thus drive both bearings into position simultaneously.
26. F/B operating lever (short) T/L 34. Front Brake Cover Plate T/L
27. Front brake lever long T/L 35. Front brake shoe pin T/L
28. Link Rod Front Brake T/L 36. Washer Front brake shoe pin T/L
29. L/Rod Trunnion (RH Thread) T/L 37. Nut Front brake shoe pin T/L
30. L/Rod Trunnion Nut (RH) T/L 38. Front brake operating cam
39. Washer front brake operating
31. L/Rod Trunnion (L/H) T/L (NF) cam
32. L/Rod Trunnion Nut (LH) T/L (NF) 40. Nut front brake operating cam
33. Front brake shoes C/W lining T/L
If tightening the nuts makes the spindle hard to turn, the bearings are bottoming in the recesses in the hub barrel and
the inner races are not resting on the shoulder of the spindle. In this case, the bearing should be removed and a thin
packing shim should be fitted between the inner race and the shoulder on the spindle.
Assemble the operating cam into cover plate after smearing grease on the pivot pin and the cylindrical bearing surface
of the operating cam. Fit the operating lever on its splines in a position to suit the extent of wear on the linings and
secure with the nut and washer. Note that the position of the operating lever may have to be corrected when adjusting
the brake after refitting the wheel. The range of adjustment can be extended by moving this lever on to a different
spline.
NOTE : Before replacing the felt washers which form the grease seals, pack all bearings with medium/lime soap
or aluminium soap greases or multipurpose grease. The use of H.M.P. greases which have a soda soap base is
not recommended, as these tend to be slightly corrosive if any dampness finds its way into the hubs.
Make sure the inside of the brake drum is quite free from oil or grease, dampness, etc. When replacing the speedo
drive, make sure that the dogs on the speedo drive are correctly engaged with the slots in the end of the hub barrel.
Make sure that the speedo drive is correctly positioned, so that the speedo cable would not be too stretched or will not
have any sharp bends. Replace the felt washers, distance collars, and brake cover plate and securely tighten the
spindle nuts.
The rear wheel is quickly detachable without disturbing the sprocket. Place vehicle on centre stand. Remove the split
pin and the castle nut securing the long spindle which is located on the sprocket side. Slide out the long spindle from
the wheel and remove both the spacers from the RH side fork end. Tilt the vehicle and slide out the wheel from the
chainstay. For assembly reverse the process but take care to engage the cush rubbers properly on the driving lugs.
Four rubber blocks are fitted in the pockets of centre hub and four radial vanes are formed on the back of the rear
sprocket/brake drum, thus transmitting both driving and braking torque and smoothening out harshness and
irregularity in the former.
If the cush drive rubbers are worn, and the amount of free movement measured at the tyre exceeds 1/2" to 1", the
rubbers should be replaced. The condition of the cush drive rubber in the rear wheel can be gauged by placing the
machine on the rear stand, applying the rear brake and rotating the rear wheel.
The cush rubbers are fixed in the pockets of the centre hub by means of buttons provided in the rubber blocks, thus
the rubbers are prevented from falling down when wheel is removed or refitted.
Removal of sprocket is necessary only if replacement of sprocket or attention to brakes is required. Remove the
wheel as described above. Remove the brake rod nut and disconnect the brake rod from the operating lever. Be sure
to "DISCONNECT" the stop light switch from the link, otherwise the switch will get damaged. Remove the securing
bolts of the chainguard at both front and rear ends and remove the chainguard. Disconnect the chain link. Remove the
securing nuts from brake anchor and wheel spindle. Unwrap the chain from the rear sprocket. Slide out the rear
sprocket assembly from the chainstay.
For re-assembly proceed in the reverse order. Make sure that the inside of the brake drum is quite free from oil,
grease, dampness, etc. Ensure the chain lock clip is fitted in the right direction so that the closed end of the clip is
towards the direction of motion. The rear chain should be inspected for wear before assembly. It should be renewed
when its length has increased by 1-1/8" more than a new chain. The rear chain can be adjusted by slackening the
wheel spindle nuts and brake anchor shoe pin nut and turning the notched cam plate.
After separating the cover plate from the sprocket assembly unscrew the brake shoe pivot pin lock nut and the
operating lever nut. The assembly of brake shoes, return springs, pivot pin and operating cam can be removed from
the cover plate by unscrewing the pivot pin and applying light blows with a hammer and drift on the end of the
operating cam. The return spring can then be unhooked from the brake shoes.
Brake linings are supplied in pairs and are bonded type hence linings cannot be separated and refitted with new
linings.
The bearing from the center hub can be moved by inserting a small rod of 6 mm dia. Insert the rod through the
bearing at one end and through the slit provided at the ends of the bearing distance tube. Hit the rod with a small
mallet on radially opposite sides of the bearing. The other bearing also can be removed by hitting it from opposite side
after the removal of grease seal.
To remove the hub spindle (short) and bearings from the brake drum, having already removed the brake cover plate
assembly, hit the outer end of the spindle with a brass hammer or mallet, thus driving it out of the bearing. Now the
grease seal and the bearing from the brake drum can be removed one after the other.
The fit of the bearings in the hub barrel is important as in the case of Front wheel.
To fit the bearings in the hub, use the two hollow drifts and proceed as follows. In order to make sure that there is
clearance between the inner faces of the bearings and the bottom of the recess, first fit the sealed bearing at the cush
drive side of the center hub so that the bearing will sit in the housing flush with the boss face. Then place the distance
tube from the other end and press the second bearing and also the grease seal (small).
NOTE : Before replacing the bearings in the center hub as well as the sprocket brake drum, pack with
medium/heavy lime soap or aluminum soap grease. The use of HMP greases which have soda soap base is
not recommended as these tend to be slightly corrosive if any dampness finds its way into the hub.
Make sure that the brake shoe pivot pin is really right in the cover plate and smear grease in the grooves of the pivot
pin and on the operating face of the cam. Also smear grease on the
Note that the bolt holes in the cover plate for locating the rear brake cam bush are slotted, to enable the brake shoe
assembly to be centered in the drum. The brake cover plate assembly with the shoes should be fitted over the spindle
into the brake drum and the brake applied as hard as possible by means of the operating lever. This will center the
shoes in the drum. The brake cover plate assembly should then be removed and the screws should then be tightened
fully and secured with the lock nuts. If the shoes are not correctly centered, the brake will be either ineffective or too
fierce, depending on whether the trailing or leading shoe first makes contact with the drum. With the brake assembly
correctly centered, the screws securing the cam housing correctly tightened, wear on both linings should be
approximately equal.
Check slackness of the drive chain every 1000 Km and adjust if necessary. The frequency of adjustment depends
entirely on the rider habits and usage conditions. If the chain is adjusted too loose or too tight, the chain may either
jump off the sprocket or might break, causing serious damage to vehicle/engine parts and may also lead to serious
accident.
Place the vehicle on its center stand on a firm flat surface. Unfold and remove the split pin (1) on the castle nut on LH
side of rear wheel. Loosen the castle nut (2). Loosen the stub axle nut (3) and rear brake anchor pin nut (4). Move the
cam adjusters to the same number of notches on either side of the axle. Rotate the rear wheel and check the chain
tension on the top run of the chain. The minimum free play of the chain should be 25 to 30 mm with the vehicle on its
center stand. Check the wheel alignment of front and rear wheel, using a straight edge or by means of stretching a
rope from the front wheel to rear wheel. Retighten the stub axle nut. Rotate the rear wheel, apply the rear brake hard
and hold the rear brake pedal firmly in the depressed position so that the brake assembly is centralized in the brake
drum. Retighten the brake anchor pin nut. Release the brake pedal. Ensure that the chain adjuster on the RH side is
butting against the peg on the chain stay and is not disturbed from its adjusted position. Retighten the castle nut fully
such that the split pin hole is aligned. Locate the split pin in position and bend out the split ends. Check the chain
tension again at 3 or 4 places by rotating the wheel and ensure the free play is 25 to 30 mm on the top run.
Wheel Alignment
It is usual to check the alignment of the wheels at a point about six inches above the ground. If the alignment is
checked also towards the tip of the wheels, it will be possible to ascertain whether or not the frame is twisted so as to
cause one wheel to be leaning while the other is vertical. To do that it is always necessary to remove the mudguards.
Unless a straight edge cut away in the center portion is available, it will be necessary also to remove the cylinder, tool
boxes, battery etc., in order to allow straight edge or a piece of taut string to contact the front and rear tyres.
In the later models a punch mark is provided on both the chain adjusters. These punch marks can be used as
reference marks and the chain adjusters must be moved by the same number of notches from this punch mark to
ensure proper wheel alignment.
Wheel Rims
The rim fitted to the wheel is WM 2.19" pierced with 40 holes for locating the spoke nipples.
Spokes
The spokes are of plain type 4mm dia with 90-degree countersunk heads, angle of bend 80 to 95 degree. Thread
diameter is 4.4 mm X 0.7 pitch thread. Spoke lengths are 170 mm for the rear wheel and 165 mm for the front wheel.
The spokes are laced in such a way that wheel must be built centrally in relation to the outer faces of the distance
collars which fit between the fork ends. The rim should be trued as accurately as possible, the maximum permissible
run-out both sideways and radially being plus or minus 1/32".
The key to correct lacing is that the inside and outside spokes from the flange must slope down in the opposite
direction as in the figure. The spokes are in opposite direction to the inner two spokes. In the group of four spokes
laced, the inner spokes of each flange are sloping down in the opposite direction to the outer two spokes of the next
grouping of four spokes and so on.
Lubrication
Front and rear wheel bearings are lubricated by packing them with grease every 10,000 Km, after dismantling the hub
and they require no further attention.
FRONT BRAKE: -
All Bullet 350 & 500cc models are fitted with twin leading front brakes for effective braking. These are with bonded
type brake shoes of 7" diameter.
Where brake judder or sponginess is experienced and the cause is narrowed down to uneven braking of the front
wheel, the procedure to adjust the same is as follows:
1. Link Rod
2. F/B Operating Lever (Short)
3. F/B Operating Lever (Long)
4. L/Rod Turnnion Nut (RH)
5. L/Rod Trunnion Nut (LH)
Mark four or five lines with chalk across the shoe-lining surface, assemble the cover plate to the wheel and clamp it
firmly with a nut. Hold the brake cam levers so that the brake shoe is binding lightly on the drum, and rotate the wheel
in the normal direction of rotation (anti clockwise looking from the brake drum end). Remove the brake cover plate and
observe the marks on the brake shoe surface. If the contacts were uniform, the marks on the shoe would have been
erased uniformly. If the mark on one side is not erased, it indicates that the brake shoe has to be moved towards the
drum through adjustments provided. For example, if the shoe bearing on the cam connected to the short lever has the
chalk marks intact then the shoe should be moved outwards towards the drum. For this adjustment, refit the cover
plate assembly, hold the longer brake lever pulled fully in the operating direction so that the brake shoe is binding on
the drum and proceedas follows:
Loosen the locknuts provided at both the ends of link rod and rotate the link rod clockwise so as to move the short
lever more towards the normal direction of the operation, i.e. towards the longer lever. Stop adjusting when the shoe
has moved and touches the brake drum which can be felt while making adjustment through the link rod. Then lock the
two lock nuts provided at the end of the link rod. If the marks on the shoe operated by the longer lever are not erased,
carry out above adjustments in the reverse manner (anticlockwise) ensuring that both the brake shoes are in contact
with the drum uniformly.
CAUTION : Do not attempt to rotate the link rod without loosening the locknuts and do not over-
tighten the lock nuts on the link rod. The link rod threads might snap if either of the above is
done.
Increase cable play by threading in the adjuster either at handle bar end or at fork bottom tube end.
Loosen the link rod lock nuts sufficiently at the top and bottom (L & R threads).
Turn the link rod right to left (clockwise) or in the opposite direction simultaneously checking whether the short lever
moves towards the long lever or vise versa.
Turning the link rod would be easy till the other shoe also comes in contact with the brake drum and thereafter
resistance would be felt and would be difficult to rotate further.
Release the hand lever and check for free rotation of the front wheel (No brake binding should be felt and wheel
should rotate free).
Hold link rod in position and tighten lock nuts just sufficiently. Adjust the brake cable adjusters such that brake lever
travel is 20 to 30 mm from its resting position.
NOTE : 1. The Link rod is provided with LH and RH thread for the above adjustments. Hence the correct
trunions and Lock nuts are to be used at the respective thread ends. (Refer diagram).
2. Link rod adjustment can be made to compensate for the lining wear in the normal service life which avoids
repositioning of the levers.
3. Any excessive play in the Brake cable can be corrected by using the adjuster provided in the Front Brake
Lever end at the handle bar and through the adjuster provided on the left hand fork bottom tube assembly.
CAUTION : 1. If you are in doubt, please contact the authorized dealer/distributor for their
guidance and for correct adjustment of the front brakes.
2. Any mal-adjustment of the brake system will render the brake ineffective and will affect the
safety of the rider.
Rear Brake
Set brake pedal resting position with respect to the foot rest by adjusting the stop bolt provided on the left side on the
main frame.
Turn the adjusting nut on the brake rod, clockwise to reduce pedal travel and vise versa to increase pedal travel.
The recommended travel is 20 to 30 mm. Rotate rear wheel and check for free rotation and ensure no brake binding
occurs.
TYRE S: -
Standard tyres are of size 3.23X19" for front and 3.50X19" for rear.
When removing the tyre always start close to the valve and see that the edge of the cover at the other side of the
wheel pushed down into the well.
If the correct method of fitting and removal of the tyre is adopted it will be found that the covers can be manipulated
quite easily with the small tyre levers. The use of long levers and or excessive force is liable to damage the walls of
the tyre. After inflation make sure that the tyre is fitted evenly all the way round the rim. A line molded on the wall of
the tyre indicates whether or not the tyre is correctly fitted.
Please refer the attached diagrams in Page No.59 for correct procedure for removal and refitting tyres.
1. At some time or other the need will arise to remove and replace the tyres, either as a result of a puncture or because renewal is
required to offset wear. To the inexperienced, tyre changing represents a formidable task, yet if a few simple rules are observed
and the technique learned the whole operation is surprisingly simple.
2. To remove the tyre from either wheel, first detach the wheel from the machine. Deflate the tyre by removing the valve insert and
when its is fully deflated push the beading of the tyre away from the wheel rim on both sides so that the beading enters the center
well of the rim. Remove the locking cap and push the tyre valve into the tyre.
3. Insert two tyre levers close to the valve, on either side of the valves and lever the edge of the tyre over the outside of the wheel
rim. Very little force should be necessary, if resistance is encountered it is probably due to the fact that the tyre beading have not
come off the wheel rim all round the tyre.
4. Once the tyre has been edged over the wheel rim, it is easy to work around the wheel rim so that the tyre is completely free on
one side. At this stage, the inner tube can be removed.
5. Working from the other side of the wheel, ease the other edge of the tyre over the wheel rim. Continue to work around the rim
until tyre is free completely from the rim.
6. If a puncture has necessitated the removal of the tyre, re-inflate the inner tube and immerse it in water to trace the source of the
leak. Mark its position and deflate the tube. Dry the tube and clean the area around the puncture with a petrol soaked rag. When
the surface has dried apply rubber solution and allow this to drive before removing the protective sticker from a patch and applying
the patch to the surface.
7. It is bet to use a patch of the self-vulcanizing type, which will form a very permanent repair. Note that it may be necessary to
remove another protective covering from the top surface of the patch, after it has sealed in position. Inner tubes made from
synthetic rubber may require a special type of patch and adhesive if a satisfactory bond is to be achieved.
10. To replace the tyre, inflate the inner tube just sufficiently for it to assume a circular shape. Then push it into the tyre so that it is
enclosed completely. Lay the tyre on the wheel at an angle and insert the valve through the rim tape and the hold in the wheel rim.
Attach the locking cap on the first few threads, sufficient to hold the valve captive in its correct location.
11. Starting at the point furtherest away from the value, push the tyre beading over the edge of the wheel rim until it is located in
the central well. Continue to work around the tyre in the fashion until the whole of one side of the tyre is on the rim. It may be
necessary to use a tyre lever during the final stages.
12. Make sure that there is no pull on the tyre valve and again commencing with the area furtherest from the valve, ease the other
beading of the tyre over the edge of the rim. Finish with the area close to the valve, pushing the value up into the tyre until the
locking cap touches the rim. This will ensure the inner tube is not trapped, when the last section of the beading is edged over the
rim with a tyre lever.
13. Check that the inner tube is not trapped at any point. Reinflate the inner tube, and check that the tyre is seated correctly
around the wall of the tyre on both sides, which should be equidistant from the wheel rim at all points. If the tyre is unevenly
located on the rim, try bouncing the wheel when the tyre is at the recommended pressure. It is probable that one of the beading
has not pulled clear of the center well.
14. Always run the tyre at the recommended pressures and never under or over-inflate. See specifications for recommended
pressures.
15. Tyre replacement is aided by dusting the side walls, particularly in the vicinity of the beading with a liberal coating of French
chalk.
16. Never replace the inner tube and tyre without the rim tape in position. If this precaution is overlooked there is a good chance of
the ends of the spoke nipples chafing the inner tube and causing a serious of punctures.
17. Never fit a tyre which has a damaged tread or side walls. Apart from the leval aspects there is a very great risk of a blow out,
which can have serious consequences on any who wheel vehicle.
18. Tyre valves rarely give trouble but it is always advisable to check whether the valve itself is leaking before removing the tyre.
Do not forget to fit the dust cap which forms an effective second seal. This is especially important in a high performance machine,
where centrifugal force can cause the valve insert to retract and the tyre to deflate without warning.
CAUTION : Sudden deflation may cause an accident, particularly if it occurs in the front wheel.
The A.C. lighting and Ignition system comprises of seven main components:
When the engine is started, the alternator generates AC energy which passes through the rectified DC energy. This
rectified DC gets regulated by the regulator and changes the battery depending on battery and load conditions.
Alternator
The alternator comprises of two main components, a stator and a rotor. The stator carries three pairs of series-connected
coils. The rotor is a permanent magnet. The stator and rotor can be separated without the need to fit magnetic keepers to
the rotor poles.
As the rotor turns, paid and repeated reversals of flux take place in the coil cores. These lines cut through the turns of the
coil and induce alternating voltages in that coil. External connections are taken from these coils to a regulator rectifier.
New Type Regulator - Rectifier (on vehicles produced after July 1995)
This is an improved version of the previous regulator cum rectifier. It is mounted under the seat dual.
The input and output connections are the same as in the old unit.
Salient Feature:
The modified regulator, rectifier has the advantage that in the event of the regulator failing and the ammeter not indicating
charge, the regulator can be disconnected from the circuit charging will take place without any regulation of current.
CAUTION: In case the regulator is faulty, and has been disconnected from the circuit it should be replaced through the
nearest authorised Enfield dealer to prevent overcharging of the batteryand subsequent damage to the battery and other
electrical systems.
1. Remove the 4 wire connection from the regulator cum rectifier which is mounted on the fixed mudguard of the vehicle
(just below the ignition coil)
3. Fix the new strip plate (assembled with the rectifier / regulator / flasher unit) on the front mounting studs of the seat.
4. Connect the rectifier wires to the main cable harness. Connect like-colored wires together.
1. The alternator and the regulator rectifier require no maintenance apart from ensuring that all connections are clean and
tight.
2. If the rotor, stator, engine crankshaft or rear half of the chain case has been disturbed, the air gap between the rotor
and stator should be checked for a minimum of 0.006" gap.
3. The ignition coil is located beneath the seat. It should be kept clean and terminals kept tight. When high tension cable
shows sign of perishing or cracking, it must be renewed.
The contact breaker setting should be checked after the first 800km. running, and subsequently every 5,000Kms (3000
miles).
To check or reset the gap, turn the engine over slowly until the piston is at TDC on compression stroke and the contacts
are seen to be fully open. Insert 0.35 to 0.40mm (0.014 - 0.016") feeler gauge between the contacts. Slacken the screw
"A" securing the fixed contact plate and adjust the position of the plate until the gap is the thickness of the feeler gauge,
and tighten. If the gap is correct the gauge will be a sliding fit.
To check or reset the ignition timing, rotate the crankshaft in the normal direction, until the piston is just before TDC and the
contact breaker points just commence to open. ( The best way to check the opening of the points is to switch on the ignition
and crank the engine slowly until the ammeter needle just returns to its central position. The points should just commence
to open at this position. Check the position of the piston, which should now be 0.8 mm before TDC on the compression
stroke. At this position slacken the two screws "B". Swing the base plate to the left to advance or to the right to retard the
ignition. Retighten the two screws such that the CB points gap just commences to open. To check whether the adjustment
is correct, insert a thin strip of tissue paper between the points and gently pull out the paper which should not get damaged
and should be sliding fit.
The most accurate method of setting timing is by using a dial gauge. Remove spark plug and fix a dial gauge on the spark
plug hole using a suitable adaptor. Crank engine gently so that the piston is at TDC, rotate the dial such that the needle
aligns with zero on the dial gauge.
Set the CB point gap at 0.35 to 0.4 mm and rotate the crankshaft in the opposite direction such that the piston will be 0.8
mm before TDC (This can be measured on the dial gauge). Now reset the base plate so that the points just commence to
open. This can be checked by connecting a 12 V bulb and the CB point in series with a battery. When the points are in
contact the bulb will glow and when they just open the bulb will not glow.
Smear the surface of the cam very lightly with mobile grease No. 2, high-viscosity oil or clean engine oil. Apply a drop of
clean engine oil on the contact breaker pivot. Make sure no grease or oil gets in between the contact points.
The automatic timing mechanism provided in the contact breaker housing helps in automatically advancing the ignition
timing with relation to engine speed at higher RPM.
When servicing the CB points the cam should be checked for free movement in the clockwise direction and that it is not
stuck.
To obtain access to the unit, remove contact breaker cover and the base plate assembly.
Apply a drop of clean engine oil on the fly weight pivots and the spring eyelets.
The first step is to check the timing - if it works, don't fix it! This may be done statically - with the machine not running, in a
workshop situation, or dynamically, by listening for "ping," or pre-ignition knock, while the machine is being ridden.
The most accurate method of setting timing is by using a dial gauge. Remove spark plug and fix a dial gauge on the spark
plug hole using a suitable adaptor. Crank engine gently so that the piston is at TDC, rotate the dial such that the needle
aligns with zero on the dial gauge.
In either event, the first thing to do is to check and set the contact breaker point gap - variations in gap will result in
variations in timing. Remove the contact breaker (behind the cylinder barrel - accessible from the left side of the machine)
cover, and examine the points themselves for signs of pitting or burning. Using the compression release and the kick
starter, rotate the engine until the points have opened - they will be observed to open and close as the engine turns over.
Once they've opened fully, check the gap between them with a feeler gauge - the gap should be .8 mm / .032". If not, adjust
the opening by first loosening the fixing screw, (A in the photo shown), and, using a screwdriver inserted between the two
dimples shown just below the screw and the slot opposite them, adjust the point opening until the feeler gauge is just a tight
slip fit between the points. Then tighten the fixing screw (A).
This involves rolling the engine through a compression stroke, and determining the piston position at which the spark plug
is fired by the ignition system. In a points system, this is the point at which the points open. Points opening may be
determined electrically, using a test lamp, or mechanically, by the use of a piece of thin paper, such as a cigarette paper,
placed between them, and placed under tension. The test lamp is the better alternative. Connect one wire from the lamp to
the moving point - a spring clip to the spring on the point itself is a good way. Connect the other to ground - insertion behind
the front brake or clutch lever by pulling on the lever and then releasing it as a clamp for the light wire is good.
Piston position is best determined with a simple piece of stiff wire or a small screwdriver. Remove the spark plug, first being
careful to clean the area around the plug hole. Put the gearbox in top gear with the machine on the center stand. Insert the
wire into the spark plug hole as close to vertically as possible. Then, moving the wheel around, while holding the wire in the
plug hole with the other hand, find the spot at which the piston is highest in the cylinder. This is called Top Dead Center.
(TDC) Moving the wheel back and forth, get the piston at exact TDC. Then, using your thumbnail, mark the position of the
top thread of the spark plug hole and withdraw the wire. Using a file or hacksaw blade, mark this spot on the wire. Now
make a second mark closest to the piston end of the wire, 0.8 mm closer to the piston end. this will mark the desired
position of the piston at the point opening.
Spark Plug
Owing to electrode burning, the electrode gap widens in operation and may impair the performance and economy of the
motorcycle. Therefore, the electrodes should be cleaned and adjusted to their specified gap—i.e. 0.46 to 0.50 mm. Check
the electrode gap every 5000 Km and clean and adjust if necessary.
Battery
Do not add tap water as this contains impurities. Acid should not be added unless this is accidentally spilled out of the
battery. In case of spillage, it should be replaced by dilute sulphuric acid of the same specific gravity as in the cells. Keep
the battery terminals clean, and free from corrosion by coating with pure Vaseline (not grease). Many lighting troubles can
be traced to unseen corrosion between the battery leads and the terminals on the battery. The corrosion takes place much
more frequently at the battery terminals than at other electrical contacts.
The state of charge of the battery is indicated by the specific gravity of its electrolyte If specific gravity falls to 1.110, the
battery must be recharged using an external D.C. supply at the normal recharge rate of 0.5 Amp.
NOTE : If the battery is subjected to long periods of night parking with the lights on, it may be necessary to
recharge the battery before using the motorcycle.
The unit consists of a reflector and front lens assembly which are permanently stuck together to prevent water and dust
from entering inside and spoiling the reflector.
A pre-focus bulb is used, hence no focusing device is required to be fitted. The bulb has a large flange and cap. A slot in
the flange helps in correctly positioning the bulb in the reflector. A spring loaded bulb holder, when assembled on the
reflector, ensures the bulb is held in position.
The bulb is connectedto the wiring harness with the help of lucar connectors. The bulb is 12 V 40/45 Watts.
To replace the bulb in the light unit, loosen the top screw on the fixing rim and remove the front rim and light assembly
taking care to disengage the lug at the bottom of the front rim from the fixing rim. Disconnect the lucar connectors from the
bulb terminals. Gently press and twist the bulb holder in the anticlockwise direction to remove the bulb holder. Remove the
bulb out of the reflector.
Re-assembly of the headlight bulb is the reverse order of the procedure mentioned above but care should be taken to
locate the bulb and holder correctly in the reflector.
In the event of damage to either the lens or the reflector, a new unit must be fixed.
To remove the light unit from the front rim, remove the securing spring clips holding the light unit to the rim and remove the
light unit from the rim.
While reassembling the light unit ensure the word ‘top' on the lens is towards the top of the rim and secure the spring clips
in the fixing rim ensuring that they are equally spaced around the rim.
Parking Lights
Access to the parking bulbs is obtained by removing the parking lamp rim (see illustration). This forces over the edge of the
rubber lamp body and is additionally secured by means of a small fixing screw. After removal of the lamp rim the parking
lamp lens can be pulled out of the rubber body, after which the bulb will be accessible.
The rear lamp is a combined stop and tail light and also incorporates a reflector.
Access to the bulb is obtained by removing the two screws which secure the plastic cover.
Care must be taken while replacing a new tail light assembly so that the leads to the stop/tail lamp are correctly connected,
as the use of an 18 Watt filament on the normal tail light would not only discharge the battery but could cause excessive
heat affecting the plastic cover. At the same time , the 6 watt filament, if used as stop light, will be ineffective in bright
sunlight or at night when the tail light filament is illuminated.
Horn
The machine is fitted with a 12 V x 3 Amps D.C. horn. This is a sealed unit and should never be tampered with. A screw is
provided with a locking nut at the back of the horn for tone adjustment. Do not meddle with it unless it requires adjustment.
If the horn gives only a choking sound, or does not vibrate, it does not mean that the horn has broken down. The trouble
may be due to a discharged battery, a loose connection or short-circuit in the wiring of the horn. It is also possible that the
performance of the horn may deteriorate due to its mounting becoming loose.
However, a setting screw is provided which is covered by a protective rubber cap, "B". If the horn sound is feeble then
minor corrections are possible by means of this setting screw.
« Turn in the small screw very carefully at the same time check for functioning of the horn.
« Refit the protective rubber cap over screw when adjustment is complete.
NOTE : If Ithe adjusting screw is turned in too much the horn would only give a choking sound or if it is turned out
too much the sound would be very feeble.
The three output wires from the alternator should be connectedto the main cable harness through snap on connectors.
Wiring Harness
CAUTION : Do not interchange the above connections to prevent over charging of the battery.
Regulator cum Rectifier
UK US/Canada Regular
Ignition Coil
(L T connections) UK Version : connect white wire from terminal no. 6 of ignition switch to +ve terminal of coil and
black/white wire from CB point assembly to –ve terminal of coil.
US/Canada : Connect white wire from engine stop switch at the handle bar to +ve terminal of the coil and black wire from
CB point assembly to –ve terminal of the coil.
Regular version : Connect white wire from terminal no. 4 of ignition switch +ve terminal of coil and grey wire from engine
stop switch to –ve of the coil.
HT connections : Connect HT lead to the center of the coil and the spark plug cap.
Stop-Run switch on handle bar (Only for US/Canada and Regular versions
US/Canada : Connect brown/white wire from switch to –ve terminal ammeter.
Battery
Connect the earth wire (black) from harness to –ve terminal of the battery and the main wire (red) from the fuse carrier to
the +ve terminal of the battery.
Caution : Do not connect the battery to the main cable harness without the fuse carrier and never
interchange the battery terminal connections.
SWITCHE S: -
Regular Version
Terminal Connections
Wire
Number Colour
2 ( +ve from RR
Unit) Brown
4 White
6 Brown
10 (+ve from
battery) Red
14 Blue
Handlebar Switch
The handlebar switch provided on the left side of the handlebar consists of headlamp
high & low switch (head lamp day flash only in UK & US / Canada versions) indicator
switch and horn push button. The wires are pre-soldered to the terminals and
connections are through couplers and snap connectors. The colors of the wiring
connections are given for reference purposes.
Wires Colour
Terminal
No UK US/Canada Regular Connections for
1 Blue Green Blue H-lamp supply
2 Red Red White H-lamp Hi beam
3 White White Red H-lamp Lo beam
Black /
4 - - green Indicator Lamps
Yellow /
5 - - red Indicator Supply
Black /
6 - - white Indicator Lamps
7 - - Yellow Horn
Yellow /
8 red Yellow / red - Indicator supply
Black / Black /
9 white white - Indicator lamps
Black / Black /
10 green green - Indicator lamps
13 Yellow Yellow - Horn
Horn
Connect the lucar terminals blue and yellow to the horn and ensure the protective
sleeves are in position over the connections
The front brake light switch connects inside the headlamp casing, using lucar connectors, and the rear brake wire
connections are through snap on connectors.
NOTE : Ensure all earth connections are clean and firm and the wires are fully inserted into the snap on
connectors, lucar terminals and couplers.
Check and correct any electrical faults before replacing blown fuse links.
Do Not interchange battery terminal connections and regulator cum rectifier connections.
CARBU RATOR
The starting jet system provided in this carburetor is to aid starting under adverse condition such as those experienced
during cold winter mornings.
The starting jet system comes into operation when the choke lever is pulled down, thereby lifting the choke plunger from its
seat. This enables an extra quantity of fuel to be supplied to the engine in addition to that of pilot jet system.
The action makes the fuel air mixture richer for ease of starting.
Servicing’
The carburetor should be cleaned thoroughly with petrol only. Ensure that all parts are in serviceable condition. Before
mounting the carburetor, always ensure that the slide is free to move up and down by operating the throttle twist grip. Also
ensure that the starter piston (choke plunger) is properly set in position.
CAUTION : never use a sharp instrument of wire to clean the carburetor parts especially jets and
passages. If the passages are blocked, use only pressurized air to clean the passages. Handle all parts
gently and with extreme care. Run down all threaded attachments gently. Never use force.
Mounting
Special care must be taken while mounting the carburetor. Ensure positioning of carburetor is vertical and the gasket ‘O’
ring is serviceable, to prevent any air/gas leak.
In 500 cc models rubberized inlet manifold is fitted. Check the condition for any crack, as a cracked manifold can result in
starting trouble and erratic idling speed.
Setting Idling
‘It is always recommendedto set the idling speed of the engine when the engine is still warm, i.e. after a short run.
SERVICE LIMITS
• Glazed cylinder
• Re-bore the cylinder to
next o.s
• Leaky decompressor.
• Check and change the
gaskets
2. Remove the fuel hose • No Fuel in the Tank • Fill Up the Tank
from the carburetor. Turn No, It Does Not • Blocked fuel tank cap vent • Clear the vent
the fuel tap to
ON/Reserve. Does fuel • Chocked fuel tap • Clean fuel tap
flow to the Carburetor Yes, It Flows