Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 63 views

    Lab 2 - Advanced Router Configuration

    Uploaded by

    Darwin Lajato Tipdas
    This lab involves configuring advanced settings on two routers including setting console passwords, banners, remote access passwords, hostnames, interface settings and descriptions. On Router1, a console password of 'aupece' is set along with a banner. Router2 is configured for remote Telnet access with password 'cisco'. Router1 is configured to ping Router2 by its hostname instead of IP. Interface settings like bandwidth and clock rate are adjusted on a serial link between the routers.

    Copyright:

    © All Rights Reserved
    Download as DOCX, PDF, TXT or read online from Scribd

    Lab 2 - Advanced Router Configuration

    Uploaded by

    Darwin Lajato Tipdas
    63 views3 pages
    This lab involves configuring advanced settings on two routers including setting console passwords, banners, remote access passwords, hostnames, interface settings and descriptions. On Router1, a console password of 'aupece' is set along with a banner. Router2 is configured for remote Telnet access with password 'cisco'. Router1 is configured to ping Router2 by its hostname instead of IP. Interface settings like bandwidth and clock rate are adjusted on a serial link between the routers.

    Original Description:

    TIPDAS-LAB2

    Original Title

    TIPDAS-LAB2

    Copyright

    © © All Rights Reserved

    Available Formats

    DOCX, PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    This lab involves configuring advanced settings on two routers including setting console passwords, banners, remote access passwords, hostnames, interface settings and descriptions. On Router1, a console password of 'aupece' is set along with a banner. Router2 is configured for remote Telnet access with password 'cisco'. Router1 is configured to ping Router2 by its hostname instead of IP. Interface settings like bandwidth and clock rate are adjusted on a serial link between the routers.

    Copyright:

    © All Rights Reserved
    Download as DOCX, PDF, TXT or read online from Scribd
    Download as docx, pdf, or txt
    63 views3 pages

    Lab 2 - Advanced Router Configuration

    Uploaded by

    Darwin Lajato Tipdas
    This lab involves configuring advanced settings on two routers including setting console passwords, banners, remote access passwords, hostnames, interface settings and descriptions. On Router1, a console password of 'aupece' is set along with a banner. Router2 is configured for remote Telnet access with password 'cisco'. Router1 is configured to ping Router2 by its hostname instead of IP. Interface settings like bandwidth and clock rate are adjusted on a serial link between the routers.

    Copyright:

    © All Rights Reserved
    Download as DOCX, PDF, TXT or read online from Scribd
    Download as docx, pdf, or txt
    of 3

    LAB 2 ADVANCED ROUTER CONFIGURATION

    1. In this lab you will practice using some advanced configuration and show
    commands on the Cisco router. Please remember your lab 1 commands needed to
    switch between Router modes (i.e. exit, end, disable)

    2. On Router1, configure a console password of aupece. The console user nust enter
    this password before gaining access to the user mode prompt.
    Router1(config)#line console 0
    Router1(config-line)#login
    Router1(config-line)#password aupece

    - This command will enable the prompt password. This will give a more
    secure interface because there will be multiple security check.

    3. Configure a banner that says Welcome to Router1 Authorized Users Only.


    Router1(config)# banner motd #Welcome to Router1 Authorized Users Only#

    - A banner can be added for easy identification of the interface being


    configured.

    4. Test the banner and console password by logging out of the router and logging
    back in. Get into privileged mode after successfully logging into the console.
    Router1#logout
    Password: aupece
    Router1>enable
    Password: cisco
    Router1#

    - This will check if the password and banner will be displayed before entering
    to the prompt.

    5. Configure a password of cisco on Router2 that will enable remote users to Telnet
    into it:
    Router2(config)#line vty 0 4
    Router2(config-line)#login
    Router2(config-line)#password cisco

    - This will enable the Telnet with the corresponding 5 lines to be operated and
    a password for confirmation.
    6. On Router1, associate a name of Router2 with the remote IP address 160.10.1.2.
    This will allow you to ping Router2s name rather than having to remember its IP
    address.
    Router1(config)#ip host Router2 160.10.1.2

    - This will make an easier way of communicating routers because the name is
    changed and theres no need type the IP address.

    7. Verify that the name is in Router1s host table with the show hosts command.
    Router1#show hosts

    - This will show the list of hosts installed or configured on the selected router.

    8. Ping Router2 and verify that the pings succeed.


    Router1#ping Router2

    - Checking if the ping can be made with typing the hostname that is
    configured earlier.

    9. Display the contents of flash memory on Router2. What is the name of the IOS
    image in flash and how large is it?
    Router2#show flash

    - This will show the specifications of the configured router. In this list, it
    shows the capacity of the link with its corresponding used space.
    -
    10. Display the history table on Router1. This shows the last 10 commands that were
    entered on the router. You can recall commands by entering ctrl-p or by hitting the
    up arrow key.
    Router1#show history
    Router1#ctrl-p (to see previously entered commands)

    - This will automatically input the last typed command.


    11. On Router1, do a show interfaces on Serial 1/0/0. Note on the third line of the
    output that the bandwidth is assumed to 1544 kb. This is because the router
    assumes all serial links are T1s unless you configure otherwise. Configure
    Router1s Serial 1/0/0 link to have a bandwidth of 64 kb and then reenter the show
    interfaces command.
    Router1#show interfaces Serial1/0/0
    Router1#cofigure terminal
    Router1(config)#interface Serial1/0/0
    Router1(config-if)#bandwidth 64
    Router1(config-if)#clock rate 64000
    Router1(config-if)#ctrl-z
    Router1#show interfaces Serial1/0/0

    - This will configure the clock rate and the bandwidth of the interface with
    serial link connection.

    12. On Router1, add a description to interface Serial 1/0/0 that says Serial Link to
    Router3. This description will appear whenever you issue a show interfaces
    command for Serial 1/0/0.
    Router1(config)#interface Serial1/0/0
    Router1(config-if)#description Serial Link to Router3
    Router1(config-if)#exit
    Router1(config)#exit
    Router1#show interfaces Serial1/0/0

    - This will show a description on the interface and display the desired
    description. In this one, the description is the type of link.

    You might also like