WIRELESS

SUPER G
ROUTER
USER
MANUAL
MODEL 502566

INT-502566-UM-0606-02
REGULATORY NOTES
AND STATEMENTS
Wireless LAN, Health and Authorization for Use
Radio frequency electromagnetic energy is emitted from wireless LAN devices. The energy levels
of these emissions, however, are far much less than the electromagnetic energy emissions from
wireless devices like mobile phones. Wireless LAN devices are safe for use per frequency safety
standards and recommendations. The use of wireless LAN devices may be restricted in some
situations or environments; for example, aboard airplanes, in an explosive environment or in case
the interference risk to other devices or services is perceived or identied as harmful.
In case the policy regarding the use of wireless LAN devices in specic organizations or
environments (e.g., airports, hospitals, chemical/oil/gas industrial plants, private buildings) is not
clear, please ask for authorization to use these devices prior to operating the equipment.

Regulatory Information/Disclaimers
Installation and use of this wireless LAN device must be in strict accordance with the instructions
included in the user documentation provided with the product. Any changes or modications
made to this device that are not expressly approved by the manufacturer may void the users
authority to operate the equipment. The manufacturer is not responsible for any radio or
television interference caused by unauthorized modication of this device or by any substitution
or attachment. The manufacturer and its authorized resellers or distributors will assume no liability
for any damage or violation of government regulations arising from any failure to comply with
these guidelines.

USA-FCC (Federal Communications Commission) Statement

This device complies with Part 15 of FCC Rules. Operation is subject to the following two
conditions:
1. This device may not cause interference, and
2. This device must accept any interference, including interference that may cause undesired
operation of this device.

FCC Radio Frequency Exposure Statement

This wireless LAN radio device has been evaluated under FCC Bulletin OET 65 and found
compliant to the requirements as set forth in CFR 47 Sections 2.1091, 2.1093 and 15.247 (b) (4)
addressing RF exposure from radio frequency devices. The radiated output power of this wireless
LAN device is far below the FCC radio frequency exposure limits. Nevertheless, this device
shall be used in such a manner that the potential for human contact during normal operation is
minimized.
In order to comply with RF exposure limits established in the ANSI C95.1 standards, the distance
between the antennas and the user should not be less than 20 cm.

FCC Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy. If not installed and used
in accordance with the instructions, it may cause harmful interference to radio communications.

2
REGULATORY NOTES AND STATEMENTS
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try and correct the
interference by one or more of the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the distance between the equipment and the receiver.
3. Connect the equipment to an outlet on a circuit other than that to which the receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for help.

Export Restrictions
This product or software contains encryption code that may not be exported or transferred from
the United States or Canada without an approved U.S. Department of Commerce export license.

Safety Information
Your device contains a low-power transmitter. When the device transmits, it sends out a radio
frequency (RF) signal.
CAUTION: To maintain compliance with the FCCs RF exposure guidelines, this equipment
should be installed and operated with a minimum distance of 20 cm between the radiator and
your body. Use only the supplied antenna. Any unauthorized antenna, modication or
attachments could damage the transmitter and may violate FCC regulations.
The antenna(s) used for this transmitter must be installed to provide a separation distance of at
least 20 cm from all persons and must not be co-located or operating in conjunction with any
other antenna or transmitter.

CE Mark Warning
This is a Class B product. In a domestic environment, this product may cause radio interference,
in which case the user may be required to take adequate measures.

Protection Requirements for Health and Safety Article 3.1a

Testing has been conducted for electric safety according to EN 60950. This is considered
relevant and sufcient.

Protection Requirements for Electromagnetic Compatibility

Article 3.1b
Testing has been conducted for electromagnetic compatibility according to EN 301 489-1,
EN 301 489-17 and EN 55024. This is considered relevant and sufcient.

Effective Use of the Radio Spectrum Article 3.2

Testing has been conducted for radio test suites according to EN 300 328-2. This is considered
relevant and sufcient.

CE Countries Where the Product May Be Used Freely

Germany, United Kingdom, Italy, Spain, Belgium, The Netherlands, Portugal, Greece, Ireland,
Denmark, Luxembourg, Austria, Finland, Sweden, Norway and Iceland. Also France, channels
10 through 13 only (law prohibits the use of other channels).

3
REGULATORY NOTES AND STATEMENTS
CONTENTS
section page
1. Introduction .......................................................................6

Applications............................................................................................6

Features................................................................ ..............................7

2. Unpacking and Setup .......................................................8

Unpacking..............................................................................................8

Setup..................................................................................................8

3. Hardware Installation ......................................................9

Front Panel .............................................................................9

Rear Panel .............................................................................9

Hardware Connections ..........................................................10

Connecting the router .......................................................10

Checking the installation ...................................................10

4. PC Network TCP/IP Settings .......................................... 11

Windows 95/98/Me ............................................................ 11

Windows 2000 .................................................................. 12

Windows XP ........................................................................ 13

5. Conguration .................................................................. 14

Login to the Router through a Wireless LAN ................................ 14

Login to the Wireless Super G Router ........................................ 14

Using the Web Browser .......................................................... 14

Setup Wizard ....................................................................... 15

Advanced Conguration .........................................................20

LAN settings ...................................................................20

4
TABLE OF CONTENTS
section page

Wireless ........................................................................22

Status ............................................................................25

Routing ..........................................................................28

Access ..........................................................................29

Management..................................................................35

Tools .............................................................................37
6. Technical Specications ..................................................39

General ..............................................................................39

Physical and Environmental ......................................................39

About This Manual

Congratulations on purchasing the INTELLINET NETWORK SOLUTIONS
Wireless Super G Router, Model 502566. This integrated access device
combines Internet gateway functions with a wireless LAN and Fast Ethernet
switch. It provides a complete solution for Internet surng and ofce-resource
sharing, and it is easy to congure and operate.
Purpose
This manual discusses how to install the Wireless Super G Router.
Overview of This Manual
INTRODUCTION Describes the Wireless Super G Router and its features.
UNPACKING AND SETUP Helps you get started with basic installation.
IDENTIFYING EXTERNAL COMPONENTS Describes the front panel, rear
panel and LED indicators of the Wireless Super G Router.
CONNECTING THE ROUTER Tells how you can connect the Wireless
Super G Router to your xDSL/cable modem.
TECHNICAL SPECIFICATIONS Lists the technical (general, physical and
environmental) specications of the Wireless Super G Router.

5
ABOUT THIS MANUAL
1. INTRODUCTION
With the explosive growth of the Internet, accessing information and services
at any time day or night has become a standard requirement for most
people. The era of the stand-alone PC is waning. Networking technology is
moving out of the exclusive domain of corporations and into homes with at
least two computers.
This integrated access device combines Internet gateway functions with a
wireless LAN and Fast Ethernet switch. Designed for business and the home,
it saves you the cost of installing a separate modem and ISP line for each
computer while providing ready connection for the users, with or without the
network wires.
Broadband network access is also gaining ground. However, allowing more
than two computers to access the Internet at the same time means higher costs.
Thus, there is a need to share one legal IP address over a single Internet
connection to link the home with the Internet.
With the scarcity of IP addresses, the use of a shared Internet connection
through an Internet sharing device can circumvent high network-access costs.
All linked computers can make full use of broadband capabilities over such a
device.
The INTELLINET NETWORK SOLUTIONS Wireless Super G Router not only
comes equipped with a wide range of features, but also can be installed and
congured right out of the box. This device supports a simple local area
network (LAN) and Internet access share, offering great savings.
The LAN connects home computers while also allowing any of the computers
to access the Internet, share resources or play online games the basis of the
family computing lifestyle.

APPLICATIONS
Broadband Internet access Several computers can share one high-speed
broadband connection, either wired or wireless (WLAN, LAN and WAN-
Internet).
Resource sharing Share resources such as printers, scanners and other
peripherals.
File sharing Exchange data/messages and distribute les while making
good use of hard disk space.
Online gaming Through the local area network, online gaming and
e-commerce services can be easily set up.
Firewall A built-in rewall function for security and anti-hack systems.

6
INTRODUCTION
FEATURES
High-speed data-transfer rate
Supports NAT for sharing one IP address with all LAN/WLAN users
Supports PPPoE and PPTP protocols for dial-up ADSL
Supports 64/128-bit WEP encryption
Supports WPA-PSK, WPA2-PSK, WPA, WPA2 security
Supports DHCP server/client
Supports UPnP (Universal Plug and Play)
Supports virtual server mapping
Supports packet ltering
Supports protocol ltering
Supports domain ltering
Supports DNS
Simple rewall protection
Upgradeable rmware for future functions
Simple settings using Setup Wizard
Easy conguration via Web browser

7
INTRODUCTION
2. UNPACKING AND SETUP
This section provides unpacking and setup information for the Wireless Super
G Router.

UNPACKING
Open the box of the Wireless Super G Router and carefully unpack it. The box
should contain the following items:
One Wireless Super G Router, Model 502566
One di-pole antenna
One external power adapter
One CD-ROM with this user manual
If any item is found missing or damaged, please contact your local reseller for
replacement.

SETUP
The setup of the Wireless Super G Router can be performed properly using the
following methods:
The power outlet should be within 1.82 meters (6 feet) of the router.
Visually inspect the DC power jack and make sure that it is fully secured to
the power adapter.
Make sure that there is proper heat dissipation from, and adequate
ventilation around, the router. Do not place heavy objects on the router.
Fix the direction of the antennas. Try to place the router in a position that
can best cover your wireless network. Normally, the higher you place the
antenna, the better the performance will be. The antennas position
enhances the receiving sensitivity.

8
UNPACKING AND SETUP
3. HARDWARE INSTALLATION
FRONT PANEL

Front Panel

Power This indicator lights green when the hub is receiving power;
otherwise it is off.
Status This indicator blinks green when the router is working. If it stays on or
off, the router is not working.
WAN (Link/ACT) This indicator lights green when the WAN port has
been connected to an xDSL/cable modem successfully. It blinks green while
the WAN port is transmitting or receiving data on the xDSL/cable modem.
WLAN (ACT) This indicator lights green when there are wireless devices
connected and transmitting data to the router.
Local Network (Link/ACT) These indicators light green when the LAN
ports have been connected successfully. They blink green while the LAN ports
are accessing data.

REAR PANEL

Rear Panel

Antenna There is one 2dBi gain antenna for wireless connection.

LAN (1-4) Four RJ-45 10/100Mbps Auto-MDIX ports are for connecting to
either 10Mbps or 100Mbps Ethernet connections.
WAN There is an RJ-45 10/100Mbps Auto-MDIX port for the WAN that
accommodates the xDSL/cable modem.
DC IN (POWER JACK) Plug the power adapter into this power jack.
RESET Use a pin-shaped item to push in to reset the device to factory
default settings. It will be useful when the login password is forgotten; and
will reset to default settings.

9
HARDWARE INSTALLATION
HARDWARE CONNECTIONS

Connecting the router

1. Plug in one end of the network cable to the WAN port of the router.
2. Plug in the other end of the network cable to the Ethernet port of the xDSL or
cable modem.
3. Use another network cable to connect to the Ethernet card on the computer
system; the other end of the cable connects to the LAN port of the router.
Since the Wireless Super G Router has four ports, you can connect up to
four computers directly to the unit. You do not have to buy a switch to
connect these computers since one Wireless Super G Router functions both
as a connection-sharing unit and as a switch.

Checking the installation

The control LEDs of the router are clearly visible, and the status of the network
link can be seen instantly:
1. With the power source on, once the device is connected to the broadband
modem, the Power, System, LAN, WLAN and WAN port LEDs of the router
will light up, indicating a normal status.
2. When the WAN is linked to the ADSL/cable modem, the WAN ports LED
will light up.
3. When the LAN is linked up to the computer system, the LAN ports LED will
light up.

10
HARDWARE INSTALLATION
4. PC NETWORK TCP/IP SETTINGS
The network TCP/IP settings differ based on the computers operating system
(Win95/98/Me/NT/2000/XP) and are as follows.

WINDOWS 95/98/ME
1. Click on the Network
neighborhood icon found
on the desktop.
2. Click the right mouse button
and a context menu will be
shown.
3. Select Properties to enter
the TCP/IP settings screen.
4. Select Obtain an IP address
automatically on the IP
Address eld.

5. Select Disable DNS

in the DNS Conguration
eld.

11
PC NETWORK TCP/IP SETTINGS
6. Select None for the
Gateway eld.

WINDOWS
2000/NT
Double click on the My
computer icon on the
desktop. When the My
computer window
opens, open the
Control panel and
then the Network
dialup connectionapplet.
Double click on the Local
area network connection
icon. Select Properties
to enter the TCP/IP setting
window.
1. In the Local area
network status
window, click on
Properties.
2. In the Local area
network connection
window, rst select
the TCP/IP setting
and then select
Properties.
3. Set both IP address
and DNS to the
Automatic
conguration.

12
PC NETWORK TCP/IP SETTINGS
WINDOWS XP
Point the cursor and
right click on the My
Network Place icon.
Select Properties to
enter the TCP/IP setting
window.
1. Set IP address to
Obtain an IP
address
automatically.
2. Set DNS to Obtain
DNS server address
address
automatically.

13
PC NETWORK TCP/IP SETTINGS
5. CONFIGURATION
First make sure that the network connections are functioning normally.
This Wireless Super G Router can be congured using Internet Explorer 5.0 or
newer Web browser versions.

LOGIN TO THE ROUTER THROUGH A WIRELESS LAN

Before conguring the router through a WLAN, make sure that the SSID,
Channel and WEP are set properly.
Following are the default settings used for the Wireless Super G Router:
SSID: default
Channel: 6
Security: disable

LOGIN TO THE WIRELESS SUPER G ROUTER

Before you congure this device, make sure the host PC is set on the IP
subnetwork that can be accessed by the xDSL/cable modem. For example,
when the default network address of the xDSL/cable modem Ethernet
interface is 192.168.1.x, then the host PC should be set at 192.168.1.xxx
(where xxx is a number between 2 and 254) and the default subnet mask is
255.255.255.0.

USING THE WEB BROWSER

1. Open Internet Explorer 5.0 or above (or
equivalent Internet browser).
2. Enter the IP address http://192.168.1.1
(the factory-default IP address setting) to
the URL Web address location.
3. When the following dialog box
appears, enter the username and
password to login to the main
conguration window. The default
username and password are admin.

14
CONFIGURATION
SETUP WIZARD
Setup Wizard is provided
as the part of the Web
conguration utility. You
can get the wireless
router conguration ready
to run in six easy steps by
clicking on the Wizard
button on the function
menu. The screen at the
right will appear. Click
Next to continue.

Step 1. Set your new

password
You can set and/or
change the password,
then click Next to
continue.

Step 2. Choose your time

zone
Select the time zone from the
drop-down list. Click Next
to continue.

Step 3. Set the LAN connection and DHCP server

Set your (or the users) IP address and mask. The default IP is 192.168.1.1.
If you want to enable DHCP
(Dynamic Host Conguration
Protocol), click Enabled. When
enabled, DHCP can assign IP
addresses automatically. Assign
the range of IP addresses in
the elds of Range start and
Range end. Click Next to
continue.

15
CONFIGURATION
Step 4. Set the Internet connection
Select how the router will set up the Internet connection:
Obtained IP automatically
Fixed IP address
PPPoE to obtain IP automatically
PPPoE with a xed IP address
PPTP
Obtain IP automatically (DHCP client)
If you have enabled the
DHCP server, choose
Obtain IP automatically
(DHCP client) to have the
Wireless Super G Router
assign IP addresses
automatically.

Fixed IP Address
If the Internet service
providers assign a xed
IP address, choose this
option and enter the
assigned IP address,
subnet mask, gateway
IP and DNS IP addresses
for the Wireless Super
G Router.

16
CONFIGURATION
PPPoE to obtain IP
automatically
If connected to the
Internet using a PPPoE
(dial-up xDSL) modem,
the ISP will provide a
password and
username, and then the
ISP uses PPPoE. Choose
this option and enter the
required information.

PPPoE with a xed IP

address
If connected to the
Internet using a PPPoE
(dial-up xDSL) modem,
the ISP will provide a
password, a username
and a xed IP address.
Choose this option and
enter the required
information.

17
CONFIGURATION
PPTP
If connected to the
Internet using a PPTP
(xDSL) modem, enter
your IP address, subnet
mask, gateway, server
IP, PPTP account and
PPTP password in the
appropriate elds. If
your ISP has provided
you with a connection
ID, enter it in the
Connection ID eld;
otherwise, leave it as
zero.

18
CONFIGURATION
L2TP
If connected to the
Internet using an L2TP
(dial-up xDSL) modem,
the ISP will provide a
server IP account and
password. Choose this
option and enter the
required information.

Step 5. Set Wireless LAN connection

Click Enable to enable the
wireless LAN, then type the
ESSID in the text box and select
a communications channel. The
ESSID and channel must be the
same as wireless devices
attempting to communicate to
the router.

Step 6. Setup completed

Setup Wizard is now completed.
The new settings will be effective
after the router is restarted. Click
Restart to reboot the router. If
you do not want to make any
changes, click Exit to quit
without any changes. You can
go back to modify the setting by
clicking Back.

19
CONFIGURATION
ADVANCED CONFIGURATION

LAN settings
This screen enables you to congure the LAN & DHCP server; set WAN
parameters; create administrator and user passwords; and set the local time,
time zone and dynamic DNS.
LAN & DHCP server
This screen allows you to set LAN and DHCP properties, such as the hostname,
IP address, subnet mask and domain name. LAN and DHCP proles are listed
in the DHCP table at the
bottom of the screen.
Hostname: Type the
hostname in the text box.
The hostname is required
by some ISPs. The default
hostname is AP-Router.
IP Address: This is the
IP address of the router.
The default IP address is
192.168.1.1.
Subnet Mask: Type the
subnet mask for the router
in the text box. The default subnet mask is 255.255.255.0.
DHCP Server: Enables the DHCP server to allow the router to automatically
assign IP addresses to devices connecting to the LAN. DHCP is enabled by
default. All DHCP client computers are listed in the table at the bottom of the
screen, providing the hostname, IP address and MAC address of the client.
Start IP: Type an IP address to serve as the start of the IP range that DHCP will
use to assign IP addresses to all LAN devices connected to the router.
End IP: Type an IP address to serve as the end of the IP range that DHCP will
use to assign IP addresses to all LAN devices connected to the router.
Domain Name: Type the local domain name of the network in the text box.
This item is optional.
WAN
This screen enables the user to set up the router WAN connection; specify the
IP address for the WAN; add DNS numbers; and enter the MAC address.
Connection Type: Select the connection type either DHCP client, Fixed IP,
PPPoE, PPTP or L2TP from the drop-down list.

20
CONFIGURATION
WAN IP: Select whether
you want to specify an
IP address manually or
allow DHCP to obtain an
IP address automatically.
When Specify IP is
selected, type the IP
address, subnet mask and
default gateway in the
text boxes. Your ISP will
provide this information.
DNS 1/2/3: Type up to three DNS numbers in the text boxes. Your ISP will
provide this information.
MAC Address: If required by your ISP, type the MAC address of the router
WAN interface in this eld.
Password
This screen enables you to set administrative and user passwords, which are
used to gain access to the
router interface.
Administrator: Type the
password the administrator
will use to log in to the
system. The password
must be typed again for
conrmation. The
administrator has full
control over the routers
conguration.
User: Type the password for the user to log in to the system. The password
must be typed again for conrmation. The user account can only view the
conguration, and cannot make any changes.
Time
This screen enables
the user to set the time
and date for the routers
real-time clock; select the
proper time zone; and
enable or disable
Daylight Saving.
Local Time: Displays the
local time and date.

21
CONFIGURATION
Default NTP server: The Simple Network Time Protocol (SNTP) server allows
the Wireless Super G Router to synchronize the system clock to the global
Internet through the SNTP server. Specify the NTP domain name or IP address
in the text box.
Time Zone: Select the time zone from the drop-down list.
Daylight Saving: Enables the user to enable or disable Daylight Saving Time.
When enabled, select the start and end date for Daylight Saving Time.
Dynamic DNS
This tells the DDNS
server what your current
IP address is when you
are online. You rst need
to register your preferred
DNS on the DDNS
providers. Then, select
the DDNS address in the
Server Address and ll in
the related information in the below elds: Hostname, Usename and
Password.

Wireless
This section enables the user to congure the wireless communications
parameters for the Wireless Super G Router.
Basic
This screen allows the
user to enable and
disable the wireless LAN
function; create an SSID;
and select the channel for
wireless communications.
Enable/Disable: Enables
and disables wireless
LAN via the Wireless
Super G Router.
SSID: Type an SSID in the text box. The SSID of any wireless device must
match the SSID typed here in order for the wireless device to access the LAN
and WAN via the router.
Channel: Select a transmission channel for wireless communications. The
channel of any wireless device must match the channel selected here in order
for the wireless device to access the LAN and WAN via the router.

22
CONFIGURATION
Super G mode: From the drop-down list, if you choose to use Super G to
enhance the speed, there are three options on Super G mode: Super G
without Turbo; Super G with Dynamic Turbo and Super G with Static Turbo.
The Turbo mode indicates the combination of two channels to enhance the
throughput. Super G without Turbo indicates that it is on Super G mode
without the channel combination. Dynamic Turbo is able to automatically
detect if any Super Gbased product is available. If not, the connection is via
normal G. Static Turbo means it will not go back to normal G once it starts.
Extended Range Mode: Enables and disables the extended range of the router.
Authentication
The Authentication Type
default is set to Disable.
There are four options:
Disable, WEP, WPA and
WPA2.

WEP Encryption
WEP: Open System
allows public access to
the router via wireless
communications; Shared
Key requires the user to
set a WEP key to
exchange data with other
wireless clients that have
the same WEP key.
Mode: Select the key WEP Encryption

mode in ASCII or HEX.

WEP Key: Select the level of encryption from the drop-down list. The router
supports 64- and 128-bit encryption.
Key 1 Key 4: Enables the user to create an encryption scheme for wireless
LAN transmissions. Manually enter a set of values for each key. Select a key
to use by clicking the radio button next to the key. Click Clear to erase key
values.
WPA/WPA2 Security
If WPA or WPA2 is selected, one of the following screens is shown. Set the
length of the encryption key and the parameters for the RADIUS server.

23
CONFIGURATION
Lifetime: Select the
Lifetime of the Encryption
Key (5 Minutes to 1 Day).
As soon as the lifetime
of the Encryption Key is
over, the Encryption Key
will be renewed by the
RADIUS Server.
Encryption Key: Select
the Encryption Key Length
(64 bits or 128 bits) that
you would like to use. WPA/WPA2 Security

RADIUS Server:
1. Enter the IP address,
Port used and Shared
Secret by the primary
RADIUS Server.
2. Enter the IP address,
Port used and Shared
Secret by the
secondary RADIUS
Server.

WPA-PSK/WPA2-PSK
Security
If WPA-PSK or WPA2-
PSK is selected, set the
PSK key in the Passphrase
eld. The length should
be at least eight
characters.

WPA-PSK/WPA2-PSK Security

24
CONFIGURATION
Advanced
This screen enables the user to congure advanced wireless functions.
Beacon Interval: Type
the beacon interval in the
text box. You can specify
a value from 1 to 1000.
The default beacon
interval is 100.
RTS Threshold: Type the
RTS (Request-To-Send)
threshold in the text box.
This value stabilizes data
ow. If data ow is irregular, choose values between 256 and 2432 until
data ow is normalized.
Fragmentation Threshold: Type the fragmentation threshold in the text box. If
packet transfer error rates are high, choose values between 256 and 2432
until packet transfer rates are minimized. NOTE: Setting this fragmentation
threshold value may diminish system performance.
DTIM Interval: Type a DTIM (Delivery Trafc Indication Message) interval in the
text box. You can specify a value between 1 and 65535. The default value is 1.
TX Rates (Mbps): Select one of the wireless communications transfer rates,
measured in megabytes per second, based on the speed of wireless adapters
connected to the WLAN.
11g only mode: Selecting Enable allows only 802.11g WLAN client
communication with the Wireless Super G Router.
Antenna Transmit Power: Adjust the power of the antenna transmission by
selecting from the drop-down list.

Status
This selection enables user to view the status of the router LAN, Wireless and
WAN connections, and view logs and statistics pertaining to connections and
packet transfers.
Device Information
This screen enables the user to view the routers LAN, Wireless and WAN
congurations.
Firmware Version: This area displays the latest version of the router rmware
interface. After updating the rmware in Tools/Firmware, check this to ensure
that the rmware was successfully updated.
LAN: This section displays the LAN interface conguration, including the MAC

25
CONFIGURATION
address, IP address,
subnet mask and DHCP
server status. Click DHCP
Table to view a list of
client stations currently
connected to the router
LAN interface.
Wireless: This section
displays the wireless
conguration information,
including the MAC
address, Connection
status, ESSID, Channel
and Authentication type.
WAN: This section
displays the WAN
interface conguration,
including the MAC address, Connection status, DHCP client status, IP address,
Subnet mask, Default gateway and DNS.
Click DHCP Release to release all IP addresses assigned to client stations
connected to the WAN via the router. Click DHCP Renew to reassign IP
addresses to client stations connected to the WAN.
Log
This screen enables the user to view a running log of router system statistics,
events and activities. The log displays up to 200 entries. Older entries are
overwritten by new entries. The Log screen commands are as follows:
Click First Page to view
the rst page of the log.
Click Last Page to view
the nal page of the log.
Click Previous Page to
view the page just before
the current page.
Click Next Page to view
the page just after the
current page.
Click Clear Log to delete the contents of the log and begin a new log.
Click Refresh to renew log statistics.
Time: Displays the time and date that the log entry was created.

26
CONFIGURATION
Message: Displays summary information about the log entry.
Source: Displays the source of the communication.
Destination: Displays the destination of the communication.
Note: Displays the IP address of the communication.
Log Setting
This screen enables the user to set router logging parameters.
SMTP Server: Type the
SMTP server address for
the email that the log will
be sent to in the next eld.
Send to: Type an email
address for the log to be
sent to. Click Email Log
Now to immediately
send the current log.
Syslog Server: Type the IP
address of the Syslog Server if you want the router to listen and receive
incoming Syslog messages.
Log Type: Enables the user to select what items will be included in the log:
System Activity displays information related to router operation.
Debug Information displays information related to errors and system malfunction.
Attacks displays information about any malicious activity on the network.
Dropped Packets displays information about packets that have not been
transferred successfully.
Notice displays important notices by the system administrator.
Statistic
This screen displays a table that shows the rate of packet transmission via the
router LAN, Wireless and WAN ports (in bytes per second).
Click Reset to erase all
statistics and begin
logging statistics again.

27
CONFIGURATION
Wireless
This screen enables the user to view information about wireless devices that are
connected to the Wireless Super G Router.
Connected Time: Displays
how long the wireless
device has been
connected to the LAN via
the router.
MAC Address: Displays
the devices wireless LAN
interface MAC address.

Routing
This selection enables the user to set how the router forwards data: Static or
Dynamic. Routing Table enables the user to view the information created by
the router that displays the network interconnection topology.
Static
This enables the user to set parameters by which the router forwards data to its
destination if the users network has a static IP address.
Network Address: Type
the static IP address being
used to access the
Internet. The ISP or
network administrator
provides this information.
Network Mask: Type the
network (subnet) mask for
the network. If a value
isnt entered here, the
network mask defaults to 255.255.255.255. As with Network Address, the
ISP or network administrator provides this information.
Gateway Address: Type the gateway address for the network. As with
Network Address, the ISP or network administrator provides this information.
Interface: Select an interface WAN or LAN to connect to the Internet.
Metric: Select which metric to apply to this conguration.
Add: Click to add the conguration to the static IP address table at the bottom
of the page.
Update: Select one of the entries in the static IP address table at the bottom
of the page and, after changing parameters, click Update to conrm the
changes.

28
CONFIGURATION
Delete: Select one of the entries in the static IP address table at the bottom of
the page and click Delete to remove the entry.
New: Click New to clear the text boxes and add required information to
create a new entry.
Dynamic
This screen enables the user to set NAT parameters.
NAT: Click the radio
buttons to enable or
disable the NAT function.
Transmit: Click the radio
buttons to set the desired
transmit parameters:
Disabled, RIP 1 or RIP 2.
Receive: Click the radio
buttons to set the desired
receive parameters: Disabled, RIP 1 or RIP 2.
Routing Table
This screen enables the user to view the routing table for the router. The routing
table is a database created by the router that displays the network
interconnection topology.
Network Address:
Displays the network IP
address of the connected
node.
Network Mask: Displays
the network (subnet) mask
of the connected node.
Gateway Address:
Displays the gateway
address of the connected node.
Interface: Displays whether the node is connected via a WAN or LAN.
Metric: Displays the metric of the connected node.
Type: Displays whether the node has a static or dynamic IP address.

Access
This page enables you to dene access restrictions; set up protocol and IP
lters; create virtual servers; dene access for special applications, such as
games; and set rewall rules.

29
CONFIGURATION
Filters
Using lters denies or
allows user access. There
are ve types of lters to
select from: MAC Filters,
URL Blocking, IP Filters,
Protocol Filters and
Domain Blocking.
MAC Filters
MAC Filter: Enables you
to allow or deny Internet
access to users within the
LAN based on the MAC
address of their network
interface. Click the radio
button next to Disabled to
disable the MAC lter.
Disable: The function of
the MAC lter is disabled.
Allow: Only allows
computers with a MAC
address listed in the MAC
Table.
Deny: Allows all users
Internet access except
those with computers in
the MAC Table.
MAC Table: Use this
section to create a user
prole in which Internet
access is denied or allowed. The user proles are listed in the table at the bottom
of the page. Note: Click anywhere in the item. Once the line is selected, the
elds automatically load the items parameters, which you can then edit.
Name: Type the name of the user to be permitted/denied access.
MAC Address: Type the MAC address of the users network interface.
Add: Click to add the user to the list at the bottom of the page.
Update: Click to update information if you have changed any of the elds.
Delete: Select a user from the table at the bottom of the screen and click
Delete to remove the user prole.
New: Click to erase all elds and enter new information.

30
CONFIGURATION
URL Blocking
You can enable URL
Blocking to deny users
from accessing the
specied URL. Add those
specied URLs in the text
box.

IP Filters
This screen enables you to dene a minimum and maximum IP address range
lter; all IP addresses falling in the range are not allowed Internet access. The
IP lter proles are listed in the table at the bottom of the page. Note: Click
anywhere in the item. Once the line is selected, the elds automatically load
the items parameters, which you can edit.
Enable: Click to enable
or disable the IP address
lter.
Range Start: Type the
minimum address for the
IP range. IP addresses
falling between this value
and the Range End are
not allowed to access the
Internet.
Range End: Type the
minimum address for the
IP range. IP addresses falling between this value and the Range Start are not
allowed to access the Internet.
Add: Click to add the IP range to the table at the bottom of the screen.
Update: Click to update information for the range if you have selected a list
item and have made changes.
Delete: Select a list item and click Delete to remove the item from the list.
New: Click to erase all elds and enter new information.

31
CONFIGURATION
Domain Blocking
You can specify the
domains that allow users
to access or deny by
clicking one of the two
items. Also, add the
specied domains in the
text box.

Protocol Filters
This screen enables you
to allow and deny access
based upon a
communications protocol
list you create. The
protocol lter proles are
listed in the table at the
bottom of the page.
Note: When selecting
items in the table at the
bottom, click anywhere
in the item. The line is
selected, and the elds
automatically load the
items parameters, which
you can then edit.

Virtual Server
This screen enables the user to create a virtual server via the router. If the router
is set as a virtual server, remote users requesting Web or FTP services through
the WAN are directed to local servers in the LAN. The router redirects the
request via the protocol and port numbers to the correct LAN server. The
Virtual Server proles are listed in the table at the bottom of the page.
Note: When selecting items in the table at the bottom, click anywhere in the
item. The line is selected, and the elds automatically load the items parameters,
which the user can then edit.

32
CONFIGURATION
Enable: Click to enable
or disable the virtual
server.
Name: Type a
descriptive name for the
virtual server.
Protocol: Select a
protocol (TCP or UDP) to
use with the virtual server.
Private Port: Type the port
number of the computer
on the LAN that is being
used to act as a virtual
server.
Public Port: Type the port
number on the WAN that
will be used to provide access to the virtual server.
LAN Server: Type the LAN IP address that will be assigned to the virtual server.
Add: Click to add the virtual server to the table at the bottom of the screen.
Update: Click to update information for the virtual server if the user has
selected a list item and has made changes.
Delete: Select a list item and click Delete to remove the item from the list.
New: Click to erase all elds and enter new information.
Special AP
This screen enables the user to specify special applications, such as games,
that require multiple connections that are inhibited by NAT. The special
applications proles are listed in the table at the bottom of the page. Note:
When selecting items in the table at the bottom, click anywhere in the item.
The line is selected, and the elds automatically load the items parameters,
which the user can then edit.
Enable: Click to enable or disable the application prole. When the prole is
enabled, users will be able to connect to the application via the routers WAN
connection. Click Disabled on a prole to prevent users from accessing the
application on the WAN.
Name: Type a descriptive name for the application.
Trigger: Denes the outgoing communication that determines whether the user
has legitimate access to the application.
Protocol: Select the protocol (TCP, UDP or ICMP) that can be used to
access the application.

33
CONFIGURATION
 Port Range: Type the
port range to be used to
access the application
in the text boxes.
Incoming: Denes which
incoming communications
users are permitted to
connect with.
Protocol: Select the
protocol (TCP, UDP or
ICMP) that can be
used by the incoming
communication.
Port: Type the port number that can be used for the incoming communication.
Add: Click to add the special application prole to the table at the bottom of
the screen.
Update: Click to update information for the special application if the user has
selected a list item and has made changes.
Delete: Select a list item and click Delete to remove the item from the list.
New: Click to erase all elds and enter new information.
DMZ
This screen enables the user to create a DMZ for those computers that cannot
access Internet applications properly through the router and associated security
settings. Note: Any adding of clients to the DMZ exposes the clients to security
risks such as viruses and unauthorized access.
Enable: Click to enable
or disable the DMZ.
DMZ Host IP: Type a host
IP address for the DMZ.
The computer with this IP
address acts as a DMZ
host with unlimited Internet
access.
Apply: Click to save the
settings.
Firewall Rule
This screen enables the user to set up the rewall. The router provides basic
rewall functions by ltering all the packets that enter the router using a set of
rules. The rules are in an order sequence list: the lower the rule number, the
higher the priority the rule has.

34
CONFIGURATION
Enable: Click to enable
or disable the rewall
rule prole.
Name: Type a descriptive
name for the rewall rule
prole.
Action: Select whether
to allow or deny packets
that conform to the rule.
Source: Denes the
source of the incoming
packet that the rule is applied to.
Interface: Select which interface (WAN or LAN) the rule is applied to.
IP Range Start: Type the start IP address that the rule is applied to.
IP Range End: Type the end IP address that the rule is applied to.
Destination: Denes the destination of the incoming packet that the rule is
applied to.
Interface: Select which interface (WAN or LAN) the rule is applied to.
IP Range Start: Type the start IP address that the rule is applied to.
IP Range End: Type the end IP address that the rule is applied to.
Protocol: Select the protocol (TCP, UDP or ICMP) of the destination.
Port Range: Select the port range.
Add: Click to add the rule prole to the table at the bottom of the screen.
Update: Click to update information for the rule if user have selected a list item
and have made changes.
Delete: Select a list item and click Delete to remove the item from the list.
New: Click to erase all elds and enter new information.
Priority Up: Select a rule from the list and click Priority Up to increase the
priority of the rule.
Priority Down: Select a rule from the list and click Priority Down to decrease
the priority of the rule.
Update Priority: After increasing or decreasing the priority of a rule, click
Update Priority to save the changes.

Management
Management enables the user to set up the Simple Network Management
Protocol (SNMP) and Remote Management features.
SNMP
This screen enables you to congure the SNMP.

35
CONFIGURATION
Enabled/Disabled: Click
to enable or disable the
SNMP.
System Name: A name
given to the router.
System Location: A
description of the location
of the router (normally, the
DNS name).
System Contact:
A description of the contact information for the person responsible for the router.
Community: The SNMP system name for exchanging SNMP community
messages. The name can be used to limit SNMP messages passing through
the network. The default name is public.
Trap Receiver: Type the name of the destination PC that will receive trap
messages.
Remote Management
This screen enables the user to set up remote management. Using remote
management, the router can be congured through the WAN via a Web
browser. A username and password are required to perform remote
management.
HTTP: Enables the user
to set up HTTP access for
remote management.
Allow to Ping WAN Port:
Type a range of router
IP addresses that can be
pinged from remote
locations.
UPNP Enable: UPNP (or
UPnP) is short for Universal
Plug and Play, which is a
networking architecture that provides compatibility among networking
equipment, software and peripherals. The Wireless Super G Router is a
UPnP-enabled router and will only work with other UPnP devices/software. If
the user does not want to use the UPnP functionality, selecting Disabled can
disable it.
Gaming Mode: If the user is experiencing difculties when playing online
games or even certain applications that use voice data, the user may need
to enable Gaming Mode for these applications to work correctly. When not

36
CONFIGURATION
playing games or using these voice applications, it is recommended that
Gaming Mode be disabled.
PPTP: Enables the user to set up PPTP access for remote management.
IPSec: Enables the user to set up IPSec access for remote management.
IDENT: The default is Stealth. This enables the user to set port 113 to Stealth.

Tools
This page enables the user to restart the system; save and load different
settings as proles; restore factory default settings; run a Setup Wizard to
congure router settings; upgrade the rmware; and ping remote IP addresses.
Restart
Click Restart to restart
the system in the event the
system is not performing
correctly.

Settings
This screen enables user to save settings as a prole and load proles for
different circumstances. The user can also load the factory default settings, and
run a Setup Wizard to congure the router and router interface.
Save Settings: Click
Save to save the current
conguration as a prole
that can load when
necessary.
Load Settings: Click
Browse and go to the
location of a stored
prole. Click Load to
load the proles settings.
Restore Factory Default Settings: Click Restore to restore the default settings.
All conguration changes will be lost.
Firmware
This screen enables the user to keep the router rmware up to date. Follow the
instructions below.
Download the latest rmware from the manufacturers Web site, and save it to
disk.
Click Browse and go to the location of the downloaded rmware le.

37
CONFIGURATION
Select the le and click
Upgrade to update
the rmware to the latest
release.

Ping Test
The ping test enables the
user to determine whether
an IP address or host is
present on the Internet.
Type the hostname or IP
address in the text box
and click Ping.

38
CONFIGURATION
6. TECHNICAL SPECIFICATIONS
GENERAL
Standards IEEE 802.3u 100BASE-TX Fast Ethernet
IEEE 802.11g; IEEE 802.11b
Protocol CSMA/CD
Radio Technology IEEE 802.11g Orthogonal Frequency Division
Modulation
Data Transfer Rate 802.11b: 1, 2, 5.5, 11Mbps (auto sense)
802.11g: 6, 9, 12, 18, 24, 36, 48, 54 Mbps (auto sense)
Super-GTM: 108 Mbps
Ethernet: 10 Mbps (half-duplex), 20 Mbps (full-duplex)
Fast Ethernet: 100 Mbps (half-duplex),
200 Mbps (full-duplex)
Topology Star
Receiver Sensitivity 54 Mbps: Typical -70 dBm @ 10% PER (Packet Error Rate)
11 Mbps: Typical -85 dBm @ 8% PER (Packet Error Rate)
TX Power 13 dBm typically @ 802.11g
13 dBm typically @ 802.11b
Network Cables 10BASE-T: 2-pair UTP Cat. 3,4,5 (100 m),
EIA/TIA-568 100 Ohm STP (100 m)
100BASE-TX: 2-pair UTP Cat. 5 (100 m),
EIA/TIA-568 100 Ohm STP (100 m)
Frequency Range 2412 2484 MHz ISM band (channels 1 14)
Modulation Schemes DBPSK/DQPSK/CCK/OFDM
Security 64/128-bits WEP Encryption; WPA, WPA-PSK, WPA2,
WPA2-PSK
Channels 1 11 channels (FCC); 1 13 channels (ETSI);
1 14 channels (MKK)
Number of Ports LAN: 4 x 10/100 Mbps Auto-MDIX Fast Ethernet port
WAN: 1 x 10/100 Mbps Auto-MDIX Fast Ethernet port

PHYSICAL AND ENVIRONMENTAL

DC inputs 5 VDC / 2.5 A
Power Consumption 5 W (Max)
Temperature Operating: 0 40C; Storage: -10 70C
Humidity Operating: 10% 90%; Storage: 5% 90%
Dimensions 147 x 115 x 35 mm (W x H x D) without antenna
EMI: FCC Class B, CE Mark B

39
TECHNICAL SPECIFICATIONS
 www.intellinet-network.com

Are you completely satised with this product?

Please contact your INTELLINET NETWORK SOLUTIONS dealer
with comments or questions.
Copyright INTELLINET NETWORK SOLUTIONS
All products mentioned are trademarks or registered trademarks of their respective owners.