Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • Specification For Pressure Vessel Plates, Alloy Steel, Chromium-Manganese-Silicon

    Uploaded by

    Mauricio Fernández
    113 views4 pages
    asme2

    Original Title

    SA-202

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    Report this Document
    asme2

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Flag for inappropriate content
    Download as pdf or txt
    113 views4 pages

    Specification For Pressure Vessel Plates, Alloy Steel, Chromium-Manganese-Silicon

    Uploaded by

    Mauricio Fernández
    asme2

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Flag for inappropriate content
    Download as pdf or txt
    of 4

    --`,,```,,,,````-`-`,,`,,`,`,,`---

    SPECIFICATION FOR PRESSURE VESSEL PLATES,


    ALLOY STEEL, CHROMIUM-MANGANESE-SILICON

    SA-202 /SA-202M

    (Identical with ASTM Specification A 202 /A 202M-93.)

    1. Scope A 435 /A 435M Specification for Straight-Beam Ultra-


    1.1 This specification covers chromium-manganese- sonic Examination of Steel Plates
    silicon alloy steel plates, intended particularly for welded A 577 /A 577M Specification for Ultrasonic Angle-Beam
    boilers and other pressure vessels. Examination of Steel Plates
    A 578 /A 578M Specification for Straight-Beam Ultra-
    1.2 Material under this specification is available in sonic Examination of Plain and Clad Steel Plates for
    two grades having strength levels as follows: Special Applications
    Tensile Strength,
    Grade ksi [MPa]
    A 75-95 [515-655] 3. General Requirements and Ordering
    B 85-110 [585-760]
    Information
    1.3 The maximum thickness of plates is limited only 3.1 Material supplied to this specification shall con-
    by the capacity of the composition to meet the specified form to Specification A 20 /A 20M. These requirements
    mechanical property requirements; however, current outline the testing and retesting methods and procedures,
    practice normally limits the maximum thickness of plates permissible variations in dimensions and mass, quality
    furnished under this specification to 2 in. [50 mm]. and repair of defects, marking, loading, etc.

    1.4 Grade A is suitable for rivets and when so used 3.2 Specification A 20 /A 20M also establishes the
    the bars shall be subject to the requirements for rolled rules for the basis of purchase that should be complied
    bars specified in Specification A 31, except for the chemi- with when purchasing material to this specification.
    cal and mechanical requirements. 3.3 In addition to the basic requirements of this speci-
    1.5 The values stated in either inch-pound units or fication, certain supplementary requirements are available
    SI units are to be regarded separately as standard. Within when additional control, testing, or examination is
    the text, the SI units are shown in brackets. The values required to meet end use requirements. These include:
    stated in each system are not exact equivalents. Therefore, 3.3.1 Vacuum treatment,
    each system must be used independently of the other. 3.3.2 Additional or special tension testing,
    Combining values from the two systems may result in
    nonconformance with this specification. 3.3.3 Impact testing, and
    3.3.4 Nondestructive examination.

    2. Referenced Documents 3.4 The purchaser is referred to the listed supplemen-


    tary requirements in this specification and to the detailed
    2.1 ASTM Standards:
    requirements in Specification A 20 /A 20M.
    A 20 /A 20M Specification for General Requirements for
    Steel Plates for Pressure Vessels 3.5 If the requirements of this specification are in
    A 31 Specification for Steel Rivets and Bars for Rivets, conflict with the requirements of Specification A 20 /A
    Pressure Vessels 20M, the requirements of this specification shall prevail.

    315

    Copyright ASME International


    Provided by IHS under license with ASME
    No reproduction or networking permitted without license from IHS Not for Resale
    SA-202 /SA-202M 2004 SECTION II

    4. Manufacture 6. Chemical Requirements


    4.1 Steelmaking Practice The steel shall be killed. 6.1 The steel shall conform to the chemical require-
    ments shown in Table 1.

    5. Heat Treatment 7. Mechanical Requirements


    5.1 Plates are normally supplied in the as-rolled condi- 7.1 Tension Test Requirements The material as rep-
    tion. The plates may be ordered normalized or stress resented by the tension-test specimens shall conform to
    relieved, or both. the requirements shown in Table 2.

    TABLE 1 TABLE 2
    CHEMICAL REQUIREMENTS TENSILE REQUIREMENTS
    Composition, % Grade A Grade B
    Elements Grade A Grade B
    ksi [MPa] ksi [MPa]
    Carbon, max A 0.17 0.25
    Tensile strength 7595 [515655] 85110 [585760]
    Manganese:
    Yield strength, min B 45 [310] 47 [325]
    Heat analysis 1.051.40 1.051.40
    Elongation in 8 in. [200 16 A 15 A
    Product analysis 0.971.52 0.971.52
    mm], min, %
    Phosphorus, max A 0.035 0.035
    Elongation in 2 in. [50 19 18
    Sulfur, max A 0.035 0.035
    mm], min, %
    Silicon:
    Heat analysis 0.600.90 0.600.90 A
    See Specification A 20/A 20M for elongation adjustments.
    Product analysis 0.540.96 0.540.96 B
    Determined by either the 0.2% offset method or the 0.5%
    Chromium: extension-under-load method.
    Heat analysis 0.350.60 0.350.60
    Product analysis 0.310.64 0.310.64
    --`,,```,,,,````-`-`,,`,,`,`,,`---

    A
    Applies to both heat and product analyses.

    316

    Copyright ASME International


    Provided by IHS under license with ASME
    No reproduction or networking permitted without license from IHS Not for Resale
    PART A FERROUS MATERIAL SPECIFICATIONS SA-202 /SA-202M

    SUPPLEMENTARY REQUIREMENTS

    Supplementary requirements shall not apply unless specified in the order.


    A list of standardized supplementary requirements for use at the option of the purchaser
    are included in Specification A 20 /A 20M. Those which are considered suitable for use
    with this specification are listed below by title.

    S1. Vacuum Treatment, S8. Ultrasonic Examination in accordance with


    Specification A 435 /A 435M,
    S2. Product Analysis,
    S9. Magnetic Particle Examination,
    S3. Simulated Post-Weld Heat Treatment of
    Mechanical Test Coupons, S11. Ultrasonic Examination in accordance with
    S4.1 Additional Tension Test, Specification A 577 /A 577M,
    S12. Ultrasonic Examination in accordance with
    Specification A 578 /A 578M, and
    S5. Charpy V-Notch Impact Test,
    S14. Bend Test.
    S6. Drop Weight Test,
    S7. High-Temperature Tension Test,
    --`,,```,,,,````-`-`,,`,,`,`,,`---

    317

    Copyright ASME International


    Provided by IHS under license with ASME
    No reproduction or networking permitted without license from IHS Not for Resale
    --`,,```,,,,````-`-`,,`,,`,`,,`---

    318

    Copyright ASME International


    Provided by IHS under license with ASME
    No reproduction or networking permitted without license from IHS Not for Resale

    You might also like