Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 17 views

    QUIZ-2: Priyesh Pandey, 11640710

    Uploaded by

    Priyesh Pandey
    The document describes a question about measuring the time period of a square wave using interrupts on an ATMEGA328p microprocessor. It provides the original question, a solution explaining that either INT0 or INT1 could be used since they are both edge-triggered, and a code example to determine which edge trigger occurs for each interrupt. The code shows that a rising edge trigger occurs for both INT0 and INT1 when they are activated. Therefore, the answer is that INT0 or INT1 could be used for this application as both provide a rising edge trigger.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    QUIZ-2: Priyesh Pandey, 11640710

    Uploaded by

    Priyesh Pandey
    17 views2 pages
    The document describes a question about measuring the time period of a square wave using interrupts on an ATMEGA328p microprocessor. It provides the original question, a solution explaining that either INT0 or INT1 could be used since they are both edge-triggered, and a code example to determine which edge trigger occurs for each interrupt. The code shows that a rising edge trigger occurs for both INT0 and INT1 when they are activated. Therefore, the answer is that INT0 or INT1 could be used for this application as both provide a rising edge trigger.

    Original Description:

    presenation on TWI in atmega

    Original Title

    TWI

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    The document describes a question about measuring the time period of a square wave using interrupts on an ATMEGA328p microprocessor. It provides the original question, a solution explaining that either INT0 or INT1 could be used since they are both edge-triggered, and a code example to determine which edge trigger occurs for each interrupt. The code shows that a rising edge trigger occurs for both INT0 and INT1 when they are activated. Therefore, the answer is that INT0 or INT1 could be used for this application as both provide a rising edge trigger.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    17 views2 pages

    QUIZ-2: Priyesh Pandey, 11640710

    Uploaded by

    Priyesh Pandey
    The document describes a question about measuring the time period of a square wave using interrupts on an ATMEGA328p microprocessor. It provides the original question, a solution explaining that either INT0 or INT1 could be used since they are both edge-triggered, and a code example to determine which edge trigger occurs for each interrupt. The code shows that a rising edge trigger occurs for both INT0 and INT1 when they are activated. Therefore, the answer is that INT0 or INT1 could be used for this application as both provide a rising edge trigger.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 2

    1

    QUIZ-2
    Priyesh Pandey , 11640710

    Objective a) INT1
    Framing the assigned question(no.-29) compati- b) INT0
    bly with ATMEGA328p. c) none of them
    d) both of them
    Original Question
    Solution
    The time period of a square wave in the audio
    frequency range is measured using an 8085 micro- As, mentioned in the question the time period
    processor by feeding the square wave to one of the of the square wave is measured using the points
    four interrupts, namely, RST 7.5, RST 6.5, RST only where a period starts or ends, therefore the
    5.5, or INT. The algorithm used starts a timer at interrupt we require to start the timer should
    the beginning of a time period, stops the timer at be edge triggered, in the given microprocessor
    the beginning of the next time period and reads interrupts both of them can be used as INT0,INT1
    the timer values for time measurement. Which of are both edge triggered and level triggered.
    the following interrupts should be selected for this Therefore the answer is c.
    application?
    a) INTR Question based on CODE
    b) RST 6.5
    c) RST 5.5 Consider the given code, and mark the correct
    d) RST 7.5 option:
    a) On using INT1, interrupt ocurs when a rising
    Solution edge triggering is occuring.
    As, mentioned in the question the time period b) On using INT1, interrupt ocurs when a falling
    of the square wave is measured using the points edge triggering is occuring.
    only where a period starts or ends, therefore the c) On using INT0, interrupt ocurs when a falling
    interrupt we require to start the timer should be edge edge triggering is occuring.
    triggered, in the given hardware interrupts only RST d) On using INT0, interrupt ocurs when a level
    7.5 is a edge triggered interrupt while the rest are triggering is occuring.
    level triggered.
    . include " m328Pdef.inc"
    Therefore well use RST 7.5 and hence the answer .ORG 0
    is d. RJMP MAIN

    Framed Question .ORG 0X02; address of INT0 interrupt


    ;. ORG 0X04; address of INT1 interrupt
    The time period of a square wave in the audio JMP TOGGLE
    frequency range is measured using an ATMEGA 32
    microprocessor by feeding the square wave to one MAIN:
    of the two interrupts, namely, INT0 or INT1. The LDI R16 , HIGH( RAMEND )
    algorithm used starts a timer at the beginning of a OUT SPH , R16
    LDI R16 , LOW( RAMEND )
    time period, stops the timer at the beginning of the OUT SPL , R16
    next time period and reads the timer values for time LDI R16 ,1<<ISC01 | 1<<ISC00
    measurement. Which of the following interrupts ; LDI R16 ,1<<ISC11 | 1<<ISC10
    should be selected for this application? sts EICRA , R16
    2

    ;PORTD ,3 for int1


    SBI PORTD ,2
    LDI R16 ,0 B11111111
    OUT DDRB , R16
    ; for setting int1 use 0x02
    LDI R16 , 0X01
    OUT EIMSK ,R16
    JUMP:
    RJMP JUMP

    TOGGLE :
    LDI R17 ,0 XFF
    OUT PORTB ,R17
    RCALL DELAY
    LDI R17 ,0 X00
    OUT PORTB ,R17
    RETI

    DELAY:
    LDI R16 ,0 XFF
    L1: LDI R17 ,0 XFF
    L2:ldi r18 ,0 X0F
    L3:
    DEC R18
    BRNE L3
    DEC R17
    BRNE L2
    DEC R16
    BRNE L1
    RET

    Solution
    From running the code and interfacing with LED
    and push button, we can easily observe that rising
    edge triggering occurs both at INT1 and INT0.
    Hence,the correct answer is a.

    You might also like