License #2858F

SAP2000 Analysis Report

Prepared by
Toshiba

Model Name: stair case.sdb

21 October 2015
stair case.sdb SAP2000 v15.1.0 - License #2858F

10. Design preferences 21 October 2015

Contents
1. Model geometry............................................................................................................................................................... 5
1.1. Joint coordinates..................................................................................................................................................... 5
1.2. Joint restraints......................................................................................................................................................... 6
1.3. Element connectivity................................................................................................................................................ 6
2. Material properties........................................................................................................................................................... 6
3. Section properties............................................................................................................................................................ 7
3.1. Frames.................................................................................................................................................................... 7
4. Load patterns................................................................................................................................................................... 8
4.1. Definitions................................................................................................................................................................ 8
5. Load cases...................................................................................................................................................................... 8
5.1. Definitions................................................................................................................................................................ 8
5.2. Static case load assignments.................................................................................................................................. 8
5.3. Response spectrum case load assignments........................................................................................................... 8
6. Structure results.............................................................................................................................................................. 9
6.1. Mass summary........................................................................................................................................................ 9
6.2. Base reactions......................................................................................................................................................... 9
7. Joint results..................................................................................................................................................................... 9
8. Frame results................................................................................................................................................................. 10
9. Material take-off............................................................................................................................................................. 11
10. Design preferences...................................................................................................................................................... 11
10.1. Steel design......................................................................................................................................................... 11
10.2. Concrete design................................................................................................................................................... 12
10.3. Aluminum design................................................................................................................................................. 12
10.4. Cold formed design.............................................................................................................................................. 13

Toshiba Page 3 of 13
stair case.sdb SAP2000 v15.1.0 - License #2858F

10. Design preferences 21 October 2015

List of Figures
Figure 1: Finite element model............................................................................................................................................ 5
Figure 2: Deformed shape................................................................................................................................................... 9

List of Tables
Table 1: Joint Coordinates................................................................................................................................................... 5
Table 2: Joint Restraint Assignments................................................................................................................................... 6
Table 3: Connectivity - Frame.............................................................................................................................................. 6
Table 4: Frame Section Assignments.................................................................................................................................. 6
Table 5: Material Properties 02 - Basic Mechanical Properties............................................................................................ 6
Table 6: Material Properties 03a - Steel Data...................................................................................................................... 6
Table 7: Material Properties 03b - Concrete Data................................................................................................................ 7
Table 8: Frame Section Properties 01 - General, Part 1 of 4............................................................................................... 7
Table 8: Frame Section Properties 01 - General, Part 2 of 4............................................................................................... 7
Table 8: Frame Section Properties 01 - General, Part 3 of 4............................................................................................... 7
Table 8: Frame Section Properties 01 - General, Part 4 of 4............................................................................................... 7
Table 9: Load Pattern Definitions......................................................................................................................................... 8
Table 10: Load Case Definitions.......................................................................................................................................... 8
Table 11: Case - Static 1 - Load Assignments..................................................................................................................... 8
Table 12: Function - Response Spectrum - User................................................................................................................. 8
Table 13: Assembled Joint Masses...................................................................................................................................... 9
Table 14: Base Reactions.................................................................................................................................................... 9
Table 15: Joint Displacements........................................................................................................................................... 10
Table 16: Joint Reactions................................................................................................................................................... 10
Table 17: Element Forces - Frames, Part 1 of 3................................................................................................................ 10
Table 17: Element Forces - Frames, Part 2 of 3................................................................................................................ 10
Table 17: Element Forces - Frames, Part 3 of 3................................................................................................................ 11
Table 18: Material List 2 - By Section Property.................................................................................................................. 11
Table 19: Preferences - Steel Design - AISC360-05-IBC2006, Part 1 of 3......................................................................... 11
Table 19: Preferences - Steel Design - AISC360-05-IBC2006, Part 2 of 3........................................................................ 12
Table 19: Preferences - Steel Design - AISC360-05-IBC2006, Part 3 of 3........................................................................ 12
Table 20: Preferences - Concrete Design - ACI 318-05/IBC2003, Part 1 of 2.................................................................... 12
Table 20: Preferences - Concrete Design - ACI 318-05/IBC2003, Part 2 of 2.................................................................... 12
Table 21: Preferences - Aluminum Design - AA-ASD 2000................................................................................................ 12
Table 22: Preferences - Cold Formed Design - AISI-ASD96.............................................................................................. 13

Toshiba Page 4 of 13
stair case.sdb SAP2000 v15.1.0 - License #2858F

10. Design preferences 21 October 2015

1. Model geometry
This section provides model geometry information, including items such as joint coordinates, joint restraints, and element
connectivity.

Y X

Figure 1: Finite element model

1.1. Joint coordinates

Table 1: Joint Coordinates

Table 1: Joint Coordinates
Joint CoordSys CoordType GlobalX GlobalY GlobalZ
mm mm mm
7 GLOBAL Cartesian -3825.00 0.00 0.00
8 GLOBAL Cartesian 2.358E-13 0.00 0.00
9 GLOBAL Cartesian 1400.00 0.00 0.00

Toshiba Page 5 of 13
stair case.sdb SAP2000 v15.1.0 - License #2858F

10. Design preferences 21 October 2015

1.2. Joint restraints

Table 2: Joint Restraint Assignments

Table 2: Joint Restraint Assignments
Joint U1 U2 U3 R1 R2 R3

7 Yes Yes Yes No No No

8 No No Yes No No No
9 No No Yes No No No

1.3. Element connectivity

Table 3: Connectivity - Frame

Table 3: Connectivity - Frame
Frame JointI JointJ Length
mm
5 7 8 3825.00
6 8 9 1400.00

Table 4: Frame Section Assignments

Table 4: Frame Section Assignments
Frame AnalSect DesignSect MatProp

5 FSEC1 N.A. Default

6 FSEC1 N.A. Default

2. Material properties
This section provides material property information for materials used in the model.

Table 5: Material Properties 02 - Basic Mechanical Properties

Table 5: Material Properties 02 - Basic Mechanical Properties
Material UnitWeight UnitMass E1 G12 U12 A1
KN/mm3 KN-s2/mm4 KN/mm2 KN/mm2 1/C
4000Psi 2.3563E-08 2.4028E-12 24.85558 10.35649 0.200000 9.9000E-06
A992Fy50 0.0000E+00 0.0000E+00 199.94798 76.90307 0.300000 1.1700E-05

Table 6: Material Properties 03a - Steel Data

Table 6: Material Properties 03a - Steel Data
Material Fy Fu FinalSlope
KN/mm2 KN/mm2

Toshiba Page 6 of 13
stair case.sdb SAP2000 v15.1.0 - License #2858F

10. Design preferences 21 October 2015

A992Fy50 0.34474 0.44816 -0.100000

Table 7: Material Properties 03b - Concrete Data

Table 7: Material Properties 03b - Concrete
Data
Material Fc FinalSlope
KN/mm2
4000Psi 0.02758 -0.100000

3. Section properties
This section provides section property information for objects used in the model.

3.1. Frames

Table 8: Frame Section Properties 01 - General, Part 1 of 4

Table 8: Frame Section Properties 01 - General, Part 1 of 4
SectionName Material Shape t3 t2 tf tw t2b tfb
mm mm mm mm mm mm
FSEC1 A992Fy50 I/Wide Flange 304.800 127.000 9.652 6.350 127.000 9.652

Table 8: Frame Section Properties 01 - General, Part 2 of 4

Table 8: Frame Section Properties 01 - General, Part 2 of 4
SectionName Area TorsConst I33 I22 AS2 AS3
mm2 mm4 mm4 mm4 mm2 mm2
FSEC1 4264.51 96511.77 65724174. 3301257.1 1935.48 2043.01
70 7

Table 8: Frame Section Properties 01 - General, Part 3 of 4

Table 8: Frame Section Properties 01 - General, Part 3 of 4
SectionName S33 S22 Z33 Z22 R33 R22
mm3 mm3 mm3 mm3 mm mm
FSEC1 431260.99 51988.30 491187.50 80716.53 124.145 27.823

Table 8: Frame Section Properties 01 - General, Part 4 of 4

Table 8: Frame Section Properties 01 - General, Part 4 of 4
SectionName AMod A2Mod A3Mod JMod I2Mod I3Mod MMod WMod

FSEC1 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000 1.000000

Toshiba Page 7 of 13
stair case.sdb SAP2000 v15.1.0 - License #2858F

10. Design preferences 21 October 2015

4. Load patterns
This section provides loading information as applied to the model.

4.1. Definitions

Table 9: Load Pattern Definitions

Table 9: Load Pattern Definitions
LoadPat DesignType SelfWtMult AutoLoad

DEAD DEAD 1.000000

5. Load cases
This section provides load case information.

5.1. Definitions

Table 10: Load Case Definitions

Table 10: Load Case Definitions
Case Type InitialCond ModalCase BaseCase DesActOpt DesignAct

DEAD LinStatic Zero Prog Det Non-

Composite
MODAL LinModal Zero Prog Det Other

5.2. Static case load assignments

Table 11: Case - Static 1 - Load Assignments

Table 11: Case - Static 1 - Load Assignments
Case LoadType LoadName LoadSF

DEAD Load pattern DEAD 1.000000

5.3. Response spectrum case load assignments

Table 12: Function - Response Spectrum - User

Table 12: Function - Response Spectrum - User
Name Period Accel FuncDamp
Sec
UNIFRS 0.000000 1.000000 0.050000

Toshiba Page 8 of 13
stair case.sdb SAP2000 v15.1.0 - License #2858F

10. Design preferences 21 October 2015

UNIFRS 1.000000 1.000000

6. Structure results
This section provides structure results, including items such as structural periods and base reactions.

Y X

Figure 2: Deformed shape

6.1. Mass summary

Table 13: Assembled Joint Masses

Table 13: Assembled Joint Masses
Joint U1 U2 U3 R1 R2 R3
KN-s2/mm KN-s2/mm KN-s2/mm KN-mm-s2 KN-mm-s2 KN-mm-s2
7 0.000000 0.000000 0.000000 0.00 0.00 0.00
8 0.000000 0.000000 0.000000 0.00 0.00 0.00
9 0.000000 0.000000 0.000000 0.00 0.00 0.00

6.2. Base reactions

Table 14: Base Reactions

Table 14: Base Reactions
OutputCase GlobalFX GlobalFY GlobalFZ GlobalMX GlobalMY GlobalMZ
KN KN KN KN-mm KN-mm KN-mm
DEAD 0.000 0.000 135196.500 0.00 177366806.3 0.00

7. Joint results
This section provides joint results, including items such as displacements and reactions.

Toshiba Page 9 of 13
stair case.sdb SAP2000 v15.1.0 - License #2858F

10. Design preferences 21 October 2015

Table 15: Joint Displacements
Table 15: Joint Displacements
Joint OutputCase U1 U2 U3 R1 R2 R3
mm mm mm Radians Radians Radians
7 DEAD 0.000000 0.000000 0.000000 0.000000 3.141341 0.000000
8 DEAD 0.000000 0.000000 0.000000 0.000000 -1.262588 0.000000
9 DEAD 0.000000 0.000000 0.000000 0.000000 0.274766 0.000000

Table 16: Joint Reactions

Table 16: Joint Reactions
Joint OutputCase F1 F2 F3 M1 M2 M3
KN KN KN KN-mm KN-mm KN-mm
7 DEAD 0.000 0.000 42616.831 0.00 0.00 0.00
8 DEAD 0.000 0.000 102834.976 0.00 0.00 0.00
9 DEAD 0.000 0.000 -10255.307 0.00 0.00 0.00

8. Frame results
This section provides frame force results.

Table 17: Element Forces - Frames, Part 1 of 3

Table 17: Element Forces - Frames, Part 1 of 3
Frame Station OutputCase P V2 V3
mm KN KN KN
5 0.00 DEAD 0.000 -42616.831 0.000
5 478.13 DEAD 0.000 -29602.268 0.000
5 956.25 DEAD 0.000 -16587.706 0.000
5 1434.38 DEAD 0.000 -3573.143 0.000
5 1912.50 DEAD 0.000 9441.419 0.000
5 2390.63 DEAD 0.000 22455.982 0.000
5 2868.75 DEAD 0.000 35470.544 0.000
5 3346.88 DEAD 0.000 48485.107 0.000
5 3825.00 DEAD 0.000 61499.669 0.000
6 0.00 DEAD 0.000 -41335.307 0.000
6 466.67 DEAD 0.000 -30975.307 0.000
6 933.33 DEAD 0.000 -20615.307 0.000
6 1400.00 DEAD 0.000 -10255.307 0.000

Table 17: Element Forces - Frames, Part 2 of 3

Table 17: Element Forces - Frames, Part 2 of 3
Frame Station OutputCase T M2 S11Max M3 PtS11Max x2S11Max
mm KN-mm KN-mm KN/mm2 KN-mm mm
5 0.00 DEAD 0.00 0.00 8.638E-15 3.725E-09 1 -152.400
5 478.13 DEAD 0.00 0.00 40.033480 17264878.26 1 -152.400
5 956.25 DEAD 0.00 0.00 65.638139 28307168.82 1 -152.400
5 1434.38 DEAD 0.00 0.00 76.813977 33126871.69 1 -152.400
5 1912.50 DEAD 0.00 0.00 73.560994 31723986.86 1 -152.400
5 2390.63 DEAD 0.00 0.00 55.879189 24098514.33 1 -152.400

Toshiba Page 10 of 13
stair case.sdb SAP2000 v15.1.0 - License #2858F

10. Design preferences 21 October 2015

5 2868.75 DEAD 0.00 0.00 23.768563 10250454.11 1 -152.400
5 3346.88 DEAD 0.00 0.00 22.770884 -9820193.80 3 152.400
5 3825.00 DEAD 0.00 0.00 83.739152 -36113429. 3 152.400
6 0.00 DEAD 0.00 0.00 83.739152 -36113429. 3 152.400
6 466.67 DEAD 0.00 0.00 44.615566 -19240952.9 3 152.400
6 933.33 DEAD 0.00 0.00 16.702515 -7203143.14 3 152.400
6 1400.00 DEAD 0.00 0.00 7.558E-15 3.260E-09 1 -152.400

Table 17: Element Forces - Frames, Part 3 of 3

Table 17: Element Forces - Frames, Part 3 of 3
Frame Station OutputCase x3S11Max S11Min PtS11Min x2S11Min x3S11Min
mm mm KN/mm2 mm mm
5 0.00 DEAD -63.500 -8.638E-15 3 152.400 -63.500
5 478.13 DEAD -63.500 -40.033480 3 152.400 -63.500
5 956.25 DEAD -63.500 -65.638139 3 152.400 -63.500
5 1434.38 DEAD -63.500 -76.813977 3 152.400 -63.500
5 1912.50 DEAD -63.500 -73.560994 3 152.400 -63.500
5 2390.63 DEAD -63.500 -55.879189 3 152.400 -63.500
5 2868.75 DEAD -63.500 -23.768563 3 152.400 -63.500
5 3346.88 DEAD -63.500 -22.770884 1 -152.400 -63.500
5 3825.00 DEAD -63.500 -83.739152 1 -152.400 -63.500
6 0.00 DEAD -63.500 -83.739152 1 -152.400 -63.500
6 466.67 DEAD -63.500 -44.615566 1 -152.400 -63.500
6 933.33 DEAD -63.500 -16.702515 1 -152.400 -63.500
6 1400.00 DEAD -63.500 -7.558E-15 3 152.400 -63.500

9. Material take-off
This section provides a material take-off.

Table 18: Material List 2 - By Section Property

Table 18: Material List 2 - By Section Property
Section ObjectType NumPieces TotalLength TotalWeight
mm KN
FSEC1 Frame 2 5225.00 0.000

10. Design preferences

This section provides the design preferences for each type of design, which typically include material reduction factors,
framing type, stress ratio limit, deflection limits, and other code specific items.

10.1. Steel design

Table 19: Preferences - Steel Design - AISC360-05-IBC2006, Part 1 of 3

Table 19: Preferences - Steel Design - AISC360-05-IBC2006, Part 1 of 3
FrameType PatLLF SRatioLim SDC ImpFactor SystemRh SystemSd SystemR SystemCd
it o s

Toshiba Page 11 of 13
stair case.sdb SAP2000 v15.1.0 - License #2858F

10. Design preferences 21 October 2015

SMF 0.750000 0.950000 D 1.000000 1.000000 0.500000 8.000000 5.500000

Table 19: Preferences - Steel Design - AISC360-05-IBC2006, Part 2 of 3

Table 19: Preferences - Steel Design - AISC360-05-IBC2006, Part 2 of 3
Omega0 NLCoeff PhiB PhiC PhiTY PhiTF PhiV PhiVRolle PhiVT
dI

3.000000 0.002000 0.900000 0.900000 0.900000 0.750000 0.900000 1.000000 0.900000

Table 19: Preferences - Steel Design - AISC360-05-IBC2006, Part 3 of 3

Table 19: Preferences - Steel Design - AISC360-05-IBC2006, Part 3 of 3
PlugWeld HSSWeldi HSSRedu DLRat SDLAndLLRat LLRat TotalRat NetRat
ng ceT

Yes ERW No 120.00000 120.000000 360.00000 240.00000 240.00000

0 0 0 0

10.2. Concrete design

Table 20: Preferences - Concrete Design - ACI 318-05/IBC2003, Part 1 of 2

Table 20: Preferences - Concrete Design - ACI 318-05/IBC2003, Part 1 of
2
MinEccen PatLLF UFLimit SeisCat PhiT

Yes 0.750000 0.950000 D 0.900000

Table 20: Preferences - Concrete Design - ACI 318-05/IBC2003, Part 2 of 2

Table 20: Preferences - Concrete Design - ACI 318-05/IBC2003, Part 2 of
2
PhiCTied PhiCSpiral PhiV PhiVSeismi PhiVJoint
c

0.650000 0.700000 0.750000 0.600000 0.850000

10.3. Aluminum design

Table 21: Preferences - Aluminum Design - AA-ASD 2000

Table 21: Preferences - Aluminum Design - AA-ASD 2000
FrameType SRatioLimit LatFact UseLatFact

Moment Frame 1.000000 1.333333 No

Toshiba Page 12 of 13
stair case.sdb SAP2000 v15.1.0 - License #2858F

10. Design preferences 21 October 2015

10.4. Cold formed design

Table 22: Preferences - Cold Formed Design - AISI-ASD96

Table 22: Preferences - Cold Formed Design - AISI-ASD96
FrameType SRatioLim OmegaBS OmegaBU OmegaBL OmegaVS OmegaVN OmegaT OmegaC
it S TB S

Braced Frame 1.000000 1.670000 1.670000 1.670000 1.670000 1.500000 1.670000 1.800000

Toshiba Page 13 of 13