X-Roc Epoxybond: Technical Data Sheet

Technical Data Sheet
X-Roc EpoxyBond
Epoxy bonding agent for fresh concrete
10270509
Product Description
X-Roc EpoxyBond is an epoxy bonding agent used to
bond fresh concrete to hardened concrete or steel. It can
also be used to protect reinforcing steel from corrosion,
and as an anti-chloride barrier and primer for concrete
repair.
Volatile Organic Content

VOC = 0 g/L
Theoretical Coverage
5m per liter (200ft2 per gallon)
Actual coverage will depend on wastage and surface
profile and can be up to 20% higher than theoretical
coverage.
Composition
X-Roc EpoxyBond is a solvent free epoxy resin containing
acid resistant fillers and wetting agents.
Packaging
1 and 5 liter packs.
2 gallon packs (USA).
Advantages
Can be applied to steel and concrete
Chloride barrier
Long open time
Waterproof
Shelf Life
18 months when stored below 35C (95F) under shade in
a dry environment.
Typical Uses
Bonding of fresh concrete to hardened concrete
Bonding of fresh concrete to steel
Prevention of chloride migration
Reinforcing steel primer and corrosion protection
Primer for concrete repair mortars
Installation Guidelines
X-Roc EpoxyBond should be applied by experienced
personnel. X-Calibur provides detailed method
statements on all its products for use in various
applications. These must be referred to prior to starting
work. The information below is a summary intended for
guidance only.
Laboratory Test Data

Property
Surface Preparation
Concrete
The substrate must be structurally sound. Loose or
unsound concrete should be removed and made good.
Surfaces must be entirely free of oil, grease, paint,
corrosion deposits, dust, laitance or other surface
deposits. The surface should be prepared by wire
brushing, light grit blasting or high pressure water
blasting to produce a lightly exposed aggregate surface.
Typical Results
Compressive strength
60MPa (8700psi)
Tensile strength
20MPa (2900psi)
Flexural strength
30MPa (4350psi)
Slant shear strength
25MPa (3625psi)
Steel
The surface should be grit blasted to minimum SA 2.
X-Roc EpoxyBond must be applied immediately after the
grit blasting has been completed.
Application Properties
Application temperature
5 to 35C (41 to 95F)
Pot life
6 hours at 20C (68F)

Maximum overlay time
Mixing
Add the hardener Part B into the base Part A and mix
using a slow speed drill (350rpm) with an X-Shield
Coating Mixer Paddle for 3 minutes, or until both
components have fully dispersed and are uniform in
color. Be sure to rotate the mixer throughout the drum.
Mix only full packs.

27
Application
Apply in a single coat by brush, taking care to work the
mixed material with the substrate. Ensure a uniform
coating is achieved and make sure no ponding occurs
when applied horizontally. When used as an
anti-chloride barrier two coats will be required. Pour
concrete within the overlay times stated above. Clean
equipment using X-Shield Solvent.
Limitations
Do not apply below 5C (41F).
Avoid excessive application.
Do not exceed overlay times.
Avoid skin contact.
Do not discard into the water system.
Health and Safety
This product is for industrial use only by trained
operatives. It is potentially hazardous if not used
correctly. Please refer to the Material Safety Data
Sheet (MSDS) prior to the purchase and use of
this product. The MSDS can be obtained via our
website www.x-calibur.us
Authorized Technical Specialist
Please note that only X-Calibur Authorized Technical
Specialists (ATSs) are permitted to change any of the
information in this data sheet or to provide written
recommendations concerning the use of this product.
Visit www.x-calibur.us for a full list of X-Calibur ATSs.
Datasheet Validity
X-Calibur makes modifications to its product datasheets
on a continuous basis. Please check the datasheet
update section on www.x-calibur.us to ensure you have
the latest version.
Warranties
X-Calibur supplies products that comply with the
properties shown on the current datasheets. In the
unlikely event that products supplied are proved not to
comply with these properties, then we will replace the
non-compliant product or refund the purchase price.
X-Calibur does not warrant or guarantee the installation
of the products as it does not have control over the
installation or end use of the products. Any suspected
defects must be reported to X-Calibur in writing within
five working days of being detected. X-Calibur
Construction Systems Inc. makes no warranty as to
merchantability or fitness for a particular purpose
and this warranty is in lieu of all other warranties
express or implied. X-Calibur Construction Systems
Inc. shall not be liable for damages of any sort including
remote or consequential damages, down time, or delay.
www.x-calibur.us

X-Roc Epoxybond: Technical Data Sheet

Uploaded by

Copyright:

Available Formats

X-Roc Epoxybond: Technical Data Sheet

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

X-Roc Epoxybond: Technical Data Sheet

Uploaded by

Copyright:

Available Formats

Technical Data Sheet

Volatile Organic Content

Laboratory Test Data

Slant shear strength

5 to 35C (41 to 95F)

6 hours at 20C (68F)

Maximum overlay time

24 hours at 20C (68F)

You might also like