Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                

K 4700

Download as pdf or txt
Download as pdf or txt
You are on page 1of 16

SPEAKER PROTECTION KIT

K4700

ainst
s sp e a kers ag
ciou ent.
your pre DC curr
Protects -on clicks and
switch

H4700IP-1
VELLEMAN NV
Legen Heirweg 33
9890 Gavere
Belgium Europe
www.velleman.be
www.velleman-kit.com
Features & Specifications

Features
This stereo loudspeaker protection will protect the loudspeakers against the switch-impulsions and the direct current
component on the output of the connected amplifier.

Suitable for: * Amplifiers with symmetrical power supply


* Amplifiers with asymmetrical power supply.

Specifications :
Switch-delay: 6 seconds
DC protection: +1V/-1V
Max. input voltage: 200Vpp + DC
Max. switching current: 10A
LED indication for: WAIT (switch-on delay) and ERROR (DC on speaker output)
Supply voltage: 220VAC
PCB dimensions: 55 x 125mm (2.2" x 4.9")

3
Assembly hints

1. Assembly (Skipping this can lead to troubles ! )


Ok, so we have your attention. These hints will help you to make this project successful. Read them carefully.

1.1 Make sure you have the right tools:

A good quality soldering iron (25-40W) with a small tip.


Wipe it often on a wet sponge or cloth, to keep it clean; then apply solder to the tip, to give it a wet look. This is called thinning and will
protect the tip, and enables you to make good connections. When solder rolls off the tip, it needs cleaning.
Thin raisin-core solder. Do not use any flux or grease.
A diagonal cutter to trim excess wires. To avoid injury when cutting excess leads, hold the lead so they
cannot fly towards the eyes.
Needle nose pliers, for bending leads, or to hold components in place.
Small blade and Phillips screwdrivers. A basic range is fine.
0.0
00
For some projects, a basic multi-meter is required, or might be handy

1.2 Assembly Hints :


Make sure the skill level matches your experience, to avoid disappointments.
Follow the instructions carefully. Read and understand the entire step before you perform each operation.
Perform the assembly in the correct order as stated in this manual
Position all parts on the PCB (Printed Circuit Board) as shown on the drawings.
Values on the circuit diagram are subject to changes.
Values in this assembly guide are correct*
Use the check-boxes to mark your progress.
Please read the included information on safety and customer service
* Typographical inaccuracies excluded. Always look for possible last minute manual updates, indicated as NOTE on a separate leaflet.

4
Assembly hints

1.3 Soldering Hints :

1- Mount the component against the PCB surface and carefully solder the leads

2- Make sure the solder joints are cone-shaped and shiny

3- Trim excess leads as close as possible to the solder joint

AXIAL COMPONENTS ARE TAPED IN THE CORRECT


MOUNTING SEQUENCE !

REMOVE THEM FROM THE TAPE ONE AT A TIME !

5
Construction

1. Diodes. Watch the polarity ! 3. Diodes. Watch the polarity !


R8 : 330K (3 - 3 - 4 - B)

R9 : 330K (3 - 3 - 4 - B)

D1 : 1N4148
D11 : 1N4007
R10 : 330K (3 - 3 - 4 - B)

D2 : 1N4148
D12 : 1N4007
R11 : 330K (3 - 3 - 4 - B)

D3 : 1N4148
D13 : 1N4007
R12 : 18K (1 - 8 - 3 - B)
D... D...

D4 : 1N4148 CATHODE
D14 : 1N4007 CATHODE

R13 : 18K (1 - 8 - 3 - B)

D5 : 1N4148

D6 : 1N4148
R14 : 47K (4 - 7 - 3 - B)

D7 : 1N4148
R15 : 47K (4 - 7 - 3 - B)

D8 : 1N4148
R16 : 47K (4 - 7 - 3 - B)

D9 : 1N4148
R17 : 47K (4 - 7 - 3 - B)

D10 : 1N4148
4. Resistor
R18 : 47 (4 - 7 - 0 - B)
R...
R19 : 680 (6 - 8 - 1 - B)
2. Zenerdiode. Watch the
R20 : 680 (6 - 8 - 1 - B)
polarity !
5. Metal film resistor

ZD1 : 6V8
R...
ZD1
CATHODE

R1 : 3K3 (3 - 3 - 2 - B)

R2 : 3K3 (3 - 3 - 2 - B)

R3 : 8K2 (8 - 2 - 2 - B)

R4 : 8K2 (8 - 2 - 2 - B)

R5 : 8K2 (8 - 2 - 2 - B)

R6 : 8K2 (8 - 2 - 2 - B)
R21 : 100K (1 - 0 - 4 - B - 9)

R7 : 8K2 (8 - 2 - 2 - B)
R22 : 100K (1 - 0 - 4 - B - 9)
Construction

6. IC socket, Watch the 9. Leds. Watch the polarity! 11. 1W vertical resistors
position of the notch !

LD1 : Red (ERROR)

IC1 : 14P
LD2 : Yellow (WAIT) LD1 R...
CATHODE

7. Transistors 10. Electrolytic Capacitor.


If the amplifier to which the module
Watch the polarity ! is to be connected has a simple

T1 : BC547B

T2 : BC547B
C1 : 1F power supply (asymmetrical

T3 : BC547B
C2 : 1F supply), i.e. an amplifier with output-

T4 : BC517
C3 : 1F elcos, the following resistances has

C4 : 1F to be mounted:

C5 : 1F C...
8. PCB tabs.
C6 : 1F
R23 : 1K2 (1 - 2 - 2 - B)

MAINS (N - L)
R24 : 1K2 (1 - 2 - 2 - B)

C7 : 100F
+V

C8 : 100F
R25 : 1K2 (1 - 2 - 2 - B)

MAN
R26 : 1K2 (1 - 2 - 2 - B)

-V
C9 : 100F

C10 : 100F

GND
ATTENTION: if the involved

PA
C11 : 220F amplifier has a symmetrical

LS LEFT power supply, those



C12 : 470F

PA
C13 : 470F resistances may NOT be

LS RIGHT mounted!

7
Construction

12. Relays 14. IC. Watch the position of the


notch!

RY...

RY1 : VR15M121C (12VDC - 15A - 1C) IC1 : LM324


RY2 : VR15M121C (12VDC - 15A - 1C)


Cover the wide connecting
broad leads with solder.

13. Transformer

CHECK THE ENTIRE MODULE PROFOUNDLY
N 6
ONCE AGAIN.

L
0

6

CHECK IF ALL SOLDERINGS ARE CORRECT
TRANSFORMER
AND THAT THERE ARE NO SHORT-CIRCUITS!

Transfo (1,2VA - 2 x 6V / 2 x 0,1A)

8
Testing

15. Testing
Connect a net-cord to the MAINS, connect the module to the net and check if after approx.+/-6 sec. the
yellow LED 'WAIT' extinguishes; at the very same moment the LED is extinguishing, one should hear the
clack of the relais switching.

Testing the Left channel :

Connect the point PA of the left channel to the point -V (figure 1.0); the red LED 'ERROR' should now be
lightening together with the yellow LED 'WAIT'.

When the connection is interrupted again (figure 2.0), the red LED should extinguish and after approx. +/-
6 sec. the yellow LED as well.

Fig. 1.0 Fig. 2.0

Repeat this testing procedure by connecting the point PA to the point +V.

9
Testing

Testing the right channel :

Connect the point PA of the right channel to the point -V (figure 3.0); the red LED 'ERROR' should now be
lightening together with the yellow LED 'WAIT'.

When the connection is interrupted again (figure 4.0), the red LED should extinguish and after approx. +/-
6 sec. the yellow LED as well.

Fig. 3.0 Fig. 4.0

Repeat this testing procedure by connecting the point PA to the point +V.

The module is now ready for being connected definitively to the amplifier.
10
Connection

16. Connection
First find a proper place to install the protection module (f.i. against the back-side of the housing).
Realise the following connections:
MAINS: this connection has to be linked to the NET-connection of the transformer in the amplifier, i.e.
AFTER the net-switch!
PA: connect this point to the speaker-output of the amplifier, respectively for the left and the right signal (fig
5.0). In case a bridge-amplifier (fig 6.0) is being used, there ought to be two "hot" connections here.
MASS: this point has to be connected to the mass of the amplifier.
LS: to this point the left resp. right loud speaker is to be connected.

To disconnect the loudspeakers manually, realise the following connections:


Install a switch between the points -V and MAN; when the switch is shut the speakers will be disconnected
permanently, when opening the switch again after approx.+/-6 sec the speakers will be reconnected as well.

REMARK. In case of amplifiers with asymmetrical power supply (i.e. having output-elcos and the resistances
R23 to R26) of more than 300W/4 Ohm or 150W/8 Ohm, it is not recommandable to disconnect the
speakers at full power during a longer period, because the just mentioned resistances could burn. In case
the protection module is being used on a bridge-amplifier with asymmetrical power supply, the diodes D7
and D8 should not be mounted; in this case the DC-protection should not be functioning anymore because
the voltage-reference of the protection-module is now opposed to the mass.

11
Connection

PA PA
LEFT LEFT
LS LS
P4700 P4700

PA MAINS PA
MAINS RIGHT RIGHT
LS LS

ON/OFF ON/OFF

POWER POWER
MAINS MAINS SUPPLY
SUPPLY

INPUT RIGHT OUTPUT RIGHT OUTPUT +

INPUT

INPUT LEFT OUTPUT LEFT OUTPUT -

STEREO POWER AMPLIFIER Fig. 5.0 BRIDGE POWER AMPLIFIER Fig. 6.0
12
PCB

17. PCB layout.

13
Diagram

18. Diagram

14
VELLEMAN NV
Legen Heirweg 33, B-9890 GAVERE
Belgium (Europe)

Modifications and typographical errors reserved Velleman nv.


H4700IP1 - 20124 - (rev.2)
5 410329 310165

You might also like