INSTALLATION AND PROGRAMMING MANUAL

1. version

HiTECH/NIVELCO
301 Oxford Valley Road, Bldg 505, Yardley, PA 19067-7111
Tel: (215) 321-6012 Fax: (215) 321-6067
Technical Support: 888.NIVELCO (888) 648-3526)
e-mail: info@hitechtech.com www.hitechtech.com

1

2
 TABLE OF CONTENT
1. Application ....................................................................................4 6. Errors, Error messages, Error codes......................................... 49
2. Technical data .............................................................................4 7. Protection of settings by hardware ............................................ 51
3. Order code....................................................................................6 8. Fuse replacement...................................................................... 52
3.1. Dimensions...................................................................................7
3.2. Safety regulation of Ex approved units.........................................8
4. Electric connection. ...............................................................9
4.1. Arrangement of the cable terminals .............................................9 Appendix
4.2. Wiring of the transmitters............................................................10
4.2.1. Wiring of the 2-wire transmitters.................................................10 1. The ID identification codes of the manufacturer........................ 53
4.2.2. Wiring 4-wire transmitters ............................11 2. The menu of theMultiCONT PRW-100...................................... 54
4.2.3. Wiring of combined system ........................................................12 3. Programming the relays ............................................................ 55
5. Programming of MultiCONT .......................................................13 4. Programming the current generators......................................... 56
5.1. Steps of programming ................................................................14 5. Measurment mode..................................................................... 57
5.1.1. Stepping between menu tables and scrolling menupoints .........15
5.1.2. Activation of devices, relays and current generators .................16
5.1.3. Assignment of (relays and current ) output ................................17
5.1.4. Editing parameter values............................................................18
5.1.5. Editing staves .............................................................................19
5.2. Putting into operation of network with MultiCONT......................20
5.2.1. Preparing transmitters ................................................................20
5.2.2. Wiring..........................................................................................21
5.2.3. Setting up of MultiCONT.............................................................21
5.3. Main menu..................................................................................27
5.4. MultiCONT configuration ............................................................28
5.5. Programming devices.................................................................35
5.6. Remote programming.................................................................36
5.6.1. Editing the linearisation table......................................................38
5.7. Relay configuration.....................................................................39
5.8. Current generator configuration .................................................45
5.9. Switching on ...............................................................................46
5.10. Measurement mode....................................................................48

3
users1

Thank you for choosing a NIVELCO instrument.

We are sure that you will be satisfied throughout its use.

1. APPLICATION
MultiCONT P-100 series is first of all a controller and display capable to provide powering for 2-wire transmitters and accomplish complex control tasks. Further
it is a MASTER for all NIVELCO made smart transmitters as well as a universal interface between field devices with HART and other components of the
process control system such as PC, PLC, displays and different actuators. MultiCONT P-100 units support communication with a maximum of 15 ordinary or 2
Ex certified HART-capable NIVELCO made 2- or 4-wire transmitters. Should a system contain more transmitters than one MultiCONT can handle further
MultiCONT units can be organized in row by RS485. Remote programming of the transmitters and downloading of the measured data is a routine for the
MultiCONT. Measured values and new values calculated from the measured ones can control different outputs such as 4 20 mA, relays and digital output.
Large DOT matrix LCD panel facilitate a wide variety of display functions including tank content visualization. The output facilities of the basic unit can be
extended with external (relay and/or current generator) modules.
Explosion proof certified versions of the MultiCONT should be accommodated in non-hazardous area.

2. TECHNICAL DATA
TYPE P
 - 1
-

Installation Wall mounting
PRC, PRD, PRW -20 C +50 C
Ambient temperature
PRH -30 C +50 C
Transmitter power supply 30 V DC 60 mA, for Ex version 22 mA
Display 120 x 32 Dot-matrix/ 128 x 64
Max. 2 x 4 20 mA, galvanically isolated
Analogue
max load 500 ohm, over-voltage protection (isolation voltage 1000 V)
Output

Relay Max. 4 x SPDT 250 V AC ; AC 1. 5 A

RS 485 interface Galvanic isolated (isolation voltage 1000 V) HART protocol
Us = 26.5 V DC (Us = 25.8 26.2 V DC Ex) 60 mA for 2-wire transmitters
HART HART output signal level 0.5 0.1 Vpp trapezoid 1200 / 2200 Hz
Input resistance 255 ohm. Cable max.75 ohm, max. 225 nF

4
users1

TYPE P
 - 1
-

Powering, relays, analogue 4 20 mA 0.5 2.5 mm2 core cross section
RS 485 interface Shielded, twisted cable pair, cross section: 0.5 2.5 mm2

Cables
Below 1500 m Shielded, twisted cable pair, min. cross section 0,5mm
HART cabling Over 1500 m Two shielded, twisted cable, min. cross section 0,8mm
Resistance max. 75 ohm, capacitance max. 225 nF
Number of transmitters to be powered 15 ordinary or maximum 4 Ex transmitters
Power supply / 85 255 V AC 50 60 Hz / 12 VA / 255 Veff
consumption / 10,5 28 V AC 50 60 Hz / 12 VA / 28 Veff
maximum voltage 10,5 40 V DC / 11 W / 40 V DC
Housing material Polycarbonate (PC)
Ingress protection IP65
Ex marking II (1) G [EEx] ia IIB
Uomax = 30 V Imax = 140 mA Pmax= 1 W
Intrinsical safety data
Lmax = 30 mH Cmax = 300 nF
Electric protection Class I/III
Mass 0.9 kg

5
users1

3. ORDER CODE

MultiCONT P 1

EXTENSION CODE ENCLOSURE CODE INPUT CODE OUTPUT CODE POWER SUPPLY CODE
Standard * R IP 65 W 1 tx with HART 1 Display only 0 85 255 V AC 1
Not possible E IP 65 with transparent cover C 4 tx with HART 4 1 relay 1 24 V AC / DC 2
IP 65 with lockable transparent 8 tx with HART 8 2 relays 2 85 255 V AC Ex 5
D
cover 15 tx with HART M 3 relays 3 24 V AC / DC Ex 6
IP 65 with transparent cover and 4 relays 4
H
heating 1 relay + 1x420 mA
5
Analogue output
2 relays + 1x420 mA
6
Analogue output
3 relays+ 1x420 mA
7
Analogue output
4 relays + 1x420 mA
8
Analogue output
4 relays + 2x420 mA
9
Analogue output
RS 485 interface A
Internet communication B
GSM communication C
Order codes of the certified units are followed by Ex tag.
* Standard units can be extended with relay-, current generator- and combined modules.

6
users1

3.1. DIMENSIONS
75.5 75.5

89.5

107
A Pg9 or M16
B Pg11 or M20 A Pg9 or M16 R 2.5
C Pg11, Pg13.5 or M20 B Pg11 or M20
A B B C
166 C Pg11, Pg13.5 or M20
A B B C 10
193

112
160

160

.7

10
R2
P
W P
C, P
D, P
H MOUNTING

ESC OK ESC OK

W
P C, P
P D, P
H

7
users1

3.2. SAFETY REGULATION FOR THE EX APPROVED UNITS

See arrangement of the Ex certified devices in 4.2.4

Explosion proof certified versions should be accommodated in non-hazardous area!

Device should be protected against direct sunshine!
Power supply and temperature data must not exceed those given in the Technical Data!
Cable of the Ex certified devices in hazardous area should be connected to the terminals L+ and L- !
Housing of the transmitters should be grounded!
Wiring to the transmitters should be made with shielded, twisted cable pair!

8
users1

4. ELECTRIC CONNECTION

4.1. ARRANGEMENT OF THE CABLE TERMINALS

After loosening threads and removing cover of
CURRENT
MAINS RELAY 1 RELAY 3
OUT 1
USER RS485 DEVICES the wiring terminal the cables can be connected.
85 ... 255V AC The same cable should not be used for AC and
10.5 ... 40V DC
A B COM DC as well as different cables should be applied
10.5 ... 28V AC
4 5 6 10 11 12 16 17 20 21 22 L + L- SH for SELV and mains voltage.
1 2 3 7 8 9 13 14 15 18 19 23 24 25 26 27 28 For requirements of the cables see Technical
Data.
( +) ( - ) A B COM

RELAY 2 RELAY 4 CURRENT MODULE RS485

OUT 2

Cable capacity (pF / m)

Number of TX
65 95 160 225
1 2800 2000 1300 1000
5 2500 1800 1100 900
10 2200 1600 1000 800
15 1850 1400 900 700

Shielding of the interconnecting cable between the transmitter and the controller should be grounded at one end preferably at the MultiCONT.
Intrinsically safe (Ex) transmitters should be connected through the terminals L+, L- to the controller. These points are galvanically isolated from the other parts
of the electronics and the power supply for the Ex transmitter is current, voltage and power limited.

9
users1

4.2. WIRING
Before wiring the units are suggested to be checked for type (all Tx with HART), value of loop current and polling address (transmitters should have
different addresses). See 5.2. Steps of set up

4.2.1. Wiring of the 2-wire transmitters

Tx 1

Tx 2

MultiCONT
Tx 3
+Us
I+ L+
255
Tx N I L
SH

HART interface
Shielding grounded
at the MultiCONT

10
users1

4.2.2. Wiring of the 4-wire transmitters

Tx 1

Tx 2
MultiCONT

Tx 3

255
I+ L
I SH

HART interface
Tx 15

85...255 VAC
10,5...28 VAC Shielding grounded
10,5...40 VDC at the MultiCONT

11
users1

4.2.3. Combined system (containing 2- and 4-wire transmitters)

Tx 1
Shielding grounded
at the MultiCONT
Tx 2

Tx 3 MultiCONT
+Us
I+ L+
255
Tx N I L
I+ SH
I
HART interface
85...255 VAC
10,5...28 VAC
10,5...40 VDC

Tx 1

Tx M

12
users1

5. PROGRAMMING OF MULTICONT
During programming the following can be performed:
Automatic detection of devices (transmitters)
connected to the MultiCONT, their taking up in the list of devices. Devices not being on the list are part of the system but unable to
communicate with the MultiCONT (see 5.2.3 Main menu/MultiCONT config/ DEV detect).
Activation, inactivation of devices (transmitters)
Theoretically all devices in the system should be working. For this, however devices should be activated, since MultiCONT will query the
activated transmitters only and those, which are inactive not. Devices wishing to be temporarily out of use for any reason can be cut out by
inactivation. (See 5.2.3 Main menu/ Devices)
Activation, inactivation of relays and current generators
Relays and current generators of the MultiCONT should also be activated (see Attachment 3 and 4)
Assignment of the MultiCONT outputs (relays, current generators) to devices (transmitters)
or to functional values composed from the measured values
Setting composition of functional values
Functional values can be composed from measured values such as difference (of e.g. two levels), sum of two measurement values,
average of measurements.
Remote programming of devices
however programming of devices is supposed to perform in the workshop before their installing and wiring.
(P01, P02, etc. parameters of the transmitters will be used in this Manual the same way as described in their Installation and Users Manual)
Programming of MultiCONT
Relay parameters and current generator parameters of the MultiCONT will be identified as RP1, RP2, RP3 and CR1, CR2, CR3 respectively.
For planning, erection and putting into operation of systems involving MultiCONT sound knowledge of the HART standard and devices
applied is required.
During programming full scale of operation such as polling of devices, function of relays and current generators will be maintained. Modifications will
only be effective after clicking OK in Main menu /Save and returning back to measurement. If the MultiCONT is left in Programming Mode by mistake, it
will automatically return to measurement after 5 minutes following the last clicking on any key (modifications will be lost!).

13
users1

5.1. STEPS OF PROGRAMMING

Programming is to perform by the 6 programming keys aided by Menus displayed on the 120x32 point graphic screen.
Images displayed on the screen can be divided in three groups. On images of the measurement/operation there are initials in the right upper corner for
Measurement, User, Relay assignments, Current generator assignments and Error report. In the right upper corner of the images for
programming/setting there is the number of the menu table with name in the same row and 3 further menu points beneath. Pointer next to the number of
the menu table showing up or down indicate further menu points above or below the 3 ones displayed. Complete overview of the programming and
menus is to be found on table 5.5.1. Detailed process of the programming is described in 5.2 and 5.5. Third group of images is the text in frame
containing information, messages and requests.
Default values, actual menu point and value or character to edit will be indicated by grey background in this Manual and displayed reversed on the
screen. Space to be filled or edited is marked with 4 and 3

Press for entering Programming mode and Menu points and for quitting

Press ESC to scroll menu Points

Keys are used for editing parameters with numbers or text, choosing local value or position of character to edit and in some menu tables

(e.g. in table 18). for marking/activating.

Keys are used for scrolling numbers and characters when editing parameters with numbers or text.

14
users1

5.1.1. Stepping between menu tables and scrolling menu points

Measurement result

1: ST300 LEV M Main menu 605 Devices 6 06

Devices 01: ST300
1.586 m Relays 02: SE300
2: Errors Current generator 03: SC300

Error report 6E Main menu 605 Relays 6 18

01: ST300 : Reply Devices 01: R_IN_1
Relays 02: R_IN_2
Current generator 03: R_IN_3

15
users1

5.1.2 Activation of devices, relays and current generators

Devices on the list may be active ( ) or inactive( ). Only active devices will be queried. Active relays and current generators operate
according to their setting, inactive relays are de-energized output of inactive current generator is 0 mA.

or
Relays 6 18 Relays 6 18
01: R_IN_1 01: R_IN_1
02: R_IN_2 or 02: R_IN_2
03: R_IN_3 03: R_IN_3

No active relay. R_IN_1 is active

Change over between active and inactive relay states with keys .

Marking/activating of other functions or features (activation of current generator, language, strategy, etc.) will be performed the same way.

Language 5 43 Language 6 43 Language 6 43

German English or English
French German German
Hungarian French French

After activating a language, it will be changed immediately.

16
users1

5.1.3. Assignment of (relay and current) outputs

During configuring relays and current generators should be assigned to field devices

- Value is taken with positive sign (for summation)

- Value is taken with negative sign (for measuring difference)
- Average will be calculated with devices of this marking

Change over with keys .

Relays 6 18 Relays 6 18
01: R_IN_1 01: R_IN_1
02: R_IN_2 02: R_IN_2
03: R_IN_3 03: R_IN_3

Relays 6 18 Relays 6 18
01: R_IN_1 01: R_IN_1
02: R_IN_2 02: R_IN_2
03: R_IN_3 03: R_IN_3

17
users1

5.1.4. Editing parameter values

MultiCONT parameters have mathematics signs and local values. Signs and value can be modified with keys .
The keys and are for reversing the sign or changing a character.

Changing sign

Parameter 23 Parameter 23
RP1 = + 0000.00 RP1 = 0000.00
RP2 = 0.00 RP2 = 0.00
RP3 = 0 RP3 = 0

Changing position of character to edit

Parameter 23 Parameter 23
RP1 = + 0000.00 RP1 = + 0000.00
RP2 = 0.00 RP2 = 0.00
RP3 = 0 RP3 = 0

Changing local value

Parameter 23 Parameter 23
RP1 = + 0000.00 RP1 = + 0010.00
RP2 = 0.00 RP2 = 0.00
RP3 = 0 RP3 = 0

18
users1

5.1.5. Editing staves

Scrolling order of staves:

ABCDEFGHIJKLMNOPQRSTUVWXYZ [ \ ] ^ _ ! # $ % & ( ) * + , - . / 0123456789 : ; < = > ? @

Short TAG 09 Short TAG 09

ST300-12 ST301-12

19
users1

5.2. PUTTING INTO OPERATION NETWORK WITH MULTICONT

5.2.1 Preparing transmitters

It is suggested to check preferably in the workshop the Polling address (in P19 or P13) and current output of the transmitters. The loop current of
the ordinary MultiCONT is max. 60mA, and max. 22mA with the Ex certified version. If the loop current exceeds this value the voltage will be too low for
the transmitters to start to work. In networks with more than one field device the units should be addressed with numbers 1 15 and the current of the
transmitters will be limited to 4mA. This constraint may be subject to overwriting with programming in some devices (se table below). It is important that
the loop power should not exceed the above limit.
Further precondition of proper operation is the different polling addresses for different devices.

Parameters of the Polling address and constant current of NIVELCO made devices
Device series Polling address parameter Constant current parameter
ST300 P19 P08
SC300 P19 P08
SE300 P19 P08
SG300 P19 P08
CT300 P19 P08
MT300 P19 P08
TB P13 N/A
NB P13 N/A
PDT ( 2 ) P13 N/A
PDT ( 4 ) P13 N/A

20
users1

5.2.2. Wiring

Wiring has to be performed according to the previous instructions as per section 2.

Technical Data and section 4. Electric Connection.

5.2.3. Setting up MultiCONT

Switching on initiates a test process, during which MultiCONT is checking the memory, which is storing settings of the unit. (See 5.9 Switching on)
This process lasting about 50 sec can be accelerated (time period. 25 sec) by pressing key ESC
In case of positive result the process will continue with polling and finally

message appears on the screen since the table of devices is empty.

No HART device

To change Language take the route Main menu/MultiCONT config/Language go to and mark the Language required with pressing keys and as
well as . To keep this language setting should be saved in Main menu/Save config menu point otherwise with re-powering of the unit default English
will return.

To detect devices start program Main menu/Local config/DEV detect

21
 users1
M

No HART device

"OK"

Main menu 6 05
Devices
Relays
Current generators

"OK"

MultiCONT config 635

MultiCONT found devices with the
DEV detect same long address and polling stops.
EXT detect Relevant devices should be found
Strategy (with the E-view software)
taken out from the network and
return to MultiCONT config
"OK"
by clicking OK.

22
Message appears
Scanning HART line
N=0...15 "OK"
Device: N

Same address

M
No HART device

Detected DEV 37 List of detected devices. No device found

At the first set up default (table of device will remain empty)
? 1: ST300 of the Short TAG i.e.
? 2: SE300 device type (order code) will appear.
? 3: XXXX After detection it can be
modified in menu point.
users1

The question is what to do if the MultiCONT fail to find all devices?

1. In this case one of the transmitters is not HART-capable. Confer name plates and 3.1 Order Code
2. There are more devices in the system than the actual MultiCONT can handle (Confer nameplate and 3.1 Order Code). Information is provided
on the route and in menu point Main menu/Local config/Report/Devices (See 5.3.) with numbers 0nn/0mm. Number of devices listed is
represented by nn and numbers of devices that can be handled is represented by mm.
3. Device is out of order. Dismount the unit and check it in the workshop.

Next steps are adding devices to the list, setting devices and activating devices

23
 users1
Detected DEV 37 "?" is to signify that the unit has answered to the
? 1: ST300 query but it is non on the list yet.
? 2: SE300 Goto to the unit to be added by
pressing keys and click
? 3: XXXX

"OK"

1: ST300 38
Add
Remove
Set Up

"OK"

Device added Adding device to the list will be represented

Press OK by the change of "?" to "+"

"OK"

24
Detected DEV 37
+ 1: ST300 Device No 1 has added to the list
Selecting Remove "+" will be changed to "?" and
? 2: SE300 device removed from the list.
? 3: XXXX

"OK"

1: ST300 38
Add Setting and viewing of features of devices
can only be performed in Set up if they are
Remove on the list (with "+" marking).
Set up

"OK"

Device: ST300 6 07
Remote Short TAG being the order code (e.g ST300)
Short TAG can be changed here.
Polling address

These steps must be carried on

"ESC"
by all instruments you wish to add
 users1
M Returning back to Measurement
Mode with key ESC message
No active device informs that MultiCONT can not
query devices in the list because
they are not activated yet.

"OK"

Main menu 6 05
Devices
Relays
Current generator

"OK"

Devices 6 06
01: ST300 None of the unit is active.
Goto the unit to activate it with
02: SE300 or and activate it with key
03: STHCL

25
Devices 6 06
01: ST300 Inactive device
02: SE300 Active device
03: STHCL

"ESC"

Main menu 6 05
Devices
Relays
Current generator

"ESC"

1: ST300 LEV M
Returning to the Measurement Mode
2.452 m the result of the measurement
should appear on the screen.
1
users1

It is essential not to mix up Polling address and list-tag of the units. Polling addresses 1 . 15 given to devices during their programming mainly in the
workshop is for the HART detection and query. MultiCONT is identifying devices on the basis of the multi-decimal list-tags 1, 8, 9, A, B, F
assigned to the unit on its detection.

Note:

If the list of DEVices was not empty at the starting of the search than the following can appear on the screen

Detected DEV 37
! 1: SE380-11 "!" included in the list, but failed to answer
"+" included in the list and answered
+ 2 : ST360-1 "?" not included in the list, but answered
? 3 : SC380

The list can be modified on Menu table 38 in menu point Add and Remove or the whole list can be erased in Main menu/Default

26
users1

5.3. MAIN MENU

Main menu can always be entered by pressing key OK . See complete menu in 5.5.1

Main menu 6 05
Devices Setting features of devices (transmitters) (See 5.6.)
Relays Programming relay working mode and parameters (See 5.7.)
Current generator Programming current generator working mode and parameters (See 5.8.)
MultiCONT config Programming features of MultiCONT (See 5.4.)

Save config Storage of settings in the operating memory

Load config Reading out of the saved parameters from the operating memory
Default Reset to Default
List of devices, parameters of relays and current generators
as well as assignment will be erased
Restart Simulate repowering (RESET)

You find this menu network in the Appendix 2.

27
users1

5.4. MULTICONT CONFIGURATION

On Menu Tables 35 the configuration of the MultiCONT can be changed. Grey field represents default (manufacturers setting).
Main menu/Default config will reset default.

Main menu 05
Relays
Current generator
MultiCONT config MultiCONT bell. 6 35
DEV keres
EXT keres
Strategy
User display
Display mode
Secret code
Language
Address
Backlight
HART test
Report
Fresh FLASH

28
users1

Detect DEV: MultiCONT will detect transmitters (max 15) in the HART network and compile a list with
Multi decimal marking 1, ,8,9,A,B,,F (See also 5.2.3 Setting up MultiCONT)

Detected DEV 637

"!" = included in the list, but failed to answer
"+" = included in the list and answered
+ 2 : ST 360-1 "?" = not included in the list, but answered
? 3 : SC380

Detect EXT: Detection of extension modules such as Relay-, Current Generator- or Combined Modules

Strategy: Performing query

Strategy 42
P by P One after the order
Manual Query selected device only

29
users1

Users image: Beyond the Measurement image M (as shown at the end of section 5.2.3) the following Users images U can be compiled in the Users
Image below (table 51) and displayed in the measurement mode for better information.

User image 6 51 3: SE380 Dist

No 3.456 ft
Bargraph 5: SC380 Lev
Double 2.458 m
Difference
Average

Difference U
+ ShortTAG1 ShortTag2
1 2 3 4 5 6 U
100% 1.054 m
0%
Average LEV U
124
List number of devices involved.
Blinking list number represents failure of the unit.
12.24 m

30
users1

Display Mode: Steps of displaying measurement results

Display mode 6 48
Being back in Measurement mode
Manual Device can be selected with
Automatic steps of 5s
Automatic stepping with 2 different space
Automatic steps 10s
Asked Result of the queried transmitter will be displayed.

Secret code: Reading or modification of the configuration of the MultiCONT can be protected with eight-digit secret code other than zero. Key next to the
menu table number represents presence of secret code. If the key is blinking access is enabled.

Secret code 44
Unlock
Change
Avert

"OK"

Avert 46
All Avert all
Modification Modification will be averted (parameters can be viewed)

31
users1

Language: Selection of the language of programming and measurement.

Language 6 43
English Selection with
German pressing key
French
Hungarian

MultiCONT address: Address (1254) for systems with several MultiCONT units connected together over RS485 interface

MultiCONT address 54

nnn

Backlight: Operation of the display backlight can be set here.

Backlight 6 36 In position Automatic clicking of

On any key switches on the backlight.
Off Backlight will be switched off automatically
about 10sec after the last button clicking.
Automatic

32
users1

HART test: HART line can be tested

HART test 45
Drive
Watch

Drive 49
No signal Continuous HART signal can be given to the system
1200 Hz (1) Selection with keys
2200 Hz (0)

Watch 50
RxD = 2200 Hz (0) Watching the line continuously result detection
CD = No (0) of trouble will be indicated
RxD= pickup

Watch 50
CD = Carrier detect, if the line is noisy 1 will prevail
RxD = 2200 Hz (0)
or waggling device may not answer.
CD = Present (1)
(See: HART test function of the transmitters)

33
users1

Report: Report provides information on the network such as number of devices (transmitters), relays, current outputs, extension modules
involved and capable to handle. Assignment of a relay or current generator to a device will be called route.

Report 6 53
Devices: 002/015 2 devices in the network out of the possible 15
Extension: 000/032 Number of extension modules (presently 0)
Relays: 004/064 4 relays from the possible 64 (external+internal=64)
Current gen.: 002/016 2 current generators (external+internal=14)
Routes: 008/100 8 routes from the possible 100
Type: PRW115 MultiCONT type (e.g. PRW115)
SW type: 01 MultiCONT software type
SW version: 00.01 MultiCONT software version
Serie: 123456 Serial number of the Main PCB
Date: 2004/01/23 Date and
Time: 0/1/50 time of loading MultiCONT software

Power cnt.: Number of switching on of MultiCONT

Fresh FLASH: For trouble-free operation of the program-memory this program should be run once a year

IMPORTANT! Do not forget to save settings in menu point Main menu/Save.

34
 users1
5.5. PROGRAMMING DEVICES (TRANSMITTERS)
Main menu 6 05
Devices
Relays
Current generator

"OK"

Devices 6 06
Go to the required devices with keys and and click
01: ST300
to enter its file in order to view and/or change parameters
02: SE300
Table of the inactive device will not appear!!
03: SG300

"OK"

Device: SG300 607

Remote programme To perform remote programming.
See details in 5.6.
Short TAG To view and change Short TAG with
and
Polling address Short address: 115 for HART detection of devices.
It can be modified even with active access lock*
Modification requires special care

35
thus it is not recommended!
Message 32 character field offered to the user to edit
any message relating to the technology or operation
Descriptor 16 character field offered to the user to
identify the process medium
Date Date to be assigned to the unit
Final ass. number n.a.
Factory ID Assigned to NIVELCO by HART Communication Foundation (fixed 151)
Device type ID NIVELCO code
1=ST300 EchoTREK (4 wire) 6=MT300 NIVOTRACK
2=SC300 EasyTREK 20=TB THERMOCONT
3=SE300 EchoTREK (2 wire) 21=NB NIVOPRESS
4=SG300 22=PDT (2) univ. controller
5=CT300 THERMOCONT 23=PDT (4) univ. controller
SW version Software version of the unit (transmitter) (See relevant Manual)
HW version Hardware version of the unit (transmitter) (See relevant Manual)
Device ID Electronic serial number of device assigned by the factory.
Major version n.a.
Device version n.a.

Parameter address of the Polling address and Access lock may be

different with different devices.
 users1
5.6. REMOTE PROGRAMMING
Select required device as described above.
Devices 6 06
01: ST300
02: SE300
03: SG300

"OK"

Device: SG300 607 Is the transmitter in Programming Mode

"OK"
Remote programming remote programming will be refused
Short TAG
To proceed quit
Polling address programming mode
HART write protect on site and click OK
"OK" Click OK-t

"OK"

Remote prog. 6 08 Key indicates protection of device settings

36
by 4 digit secret code
(See Installation and Programming Manual of the relevant device)
Unlock Making access lock inactive. After unlocking key will be blinking.
Change code To delete or change secret code
as part of the programming can only be performed
after unlocking (entering old code)*
Parameters To view and modify** parameter values.
If the access code is active
only viewing is possible*.
Save in P+C TMP Complete set of parameters will be downloaded
from the unit and saved in a temporary table (TMP)
Send TMP to DEV Complete set of parameters saved in the temporary table (TMP)
will be uploaded to the unit (to ease programming of
silos with the same shape and task).
Linear. table Editing the linearisation table (see 5.6.1.)
Echo map Displays Echo Map of ultrasound transmitters (ST300,
SE300, SG300) ***. With other devices where this feature
is not applicable Unknown DEV/comm error will be indicated
Delete TOT1 Deleting of TOT1 in devices with flow measurement
Delete TOT2 Deleting of TOT2 in devices with flow measurement
(Access with the Factory code only!)
users1

* If the access is denied the following message appears

Unlock lease
Click OK-t After entering secret code and clicking OK access is free for programming.

** Parameters entered during remote programming via MultiCONT will be sent immediately to and checked in the field device only. If the
parameter value is incorrect or not applicable the following message appears:

HART logical error Installation and Programming Manual of the

Click OK-t relevant device should be consulted.

*** Explanation of the Echo Map of the ultrasound devices

Number of echoes
Distance and amplitude of the first echo. Echo values to display
can be selected with and .
Echo 3 1 13
1.456 m -17.45 dB
Image will be displayed as stored on entering into the relevant
parameter with blinking echo measured in that very moment.
Refresh screen with click ESC and OK.

37
 Warning!

5.6.1.

users1
Editing the linearisation table
Remote program 08
Save in P+C to TMP

Programming Manual of the given transmitter).

To let the transmitter compute the measurment results according to the table, it has to be activated in parameter P48 (s. the Users and
Send TMP to DEV
Linear. table

"OK"

Linear. table 6 12 Editing by keys.

The dimensions of the data pairs are defined by
(Lin. 01) the parameters of the "measurement mode"
(Lin. 02) and the Applied measurement unit system.
(Lin. 03) In the first line the left side, in the second line
the right side data are to be edited.

"OK"

Lin. 01

01.00 m
0.00 m3/s

38
"OK"

Lin. 01

01.00 m
000000.00 m3/s

"OK"

Linear. table 6 12
Lin. 01 Disappearing of the brackets
(Lin. 02) shows that a line of the table is deleted.
(Lin. 03)
users1

5.7. RELAY CONFIGURATION

First of all relays should be assigned to a field device(s), which will be performed in the menu point Main menu/Relays/ Program/Source. (Relay operation can
also be assigned to the difference value of two devices or to the average of more devices). Secondly relevant function is to select in the menu point Main
menu/Relays/Program/Function. Finally parameters have to be programmed i.e. values of the switching points P1 and P2 entered in dimensions defined by
the Measurement Mode of the field device to which the relay has been assigned. Thus if the measurement mode is LEVEL [m] (e.g. with a device of SE-300 i.e.
P01=x1 and P00=00x), switching points have to be entered in LEVEL [m]. For overview see Menu system of the MultiCONT Attachment 3. The relay functions in
detail are as below (default cursive in grey background).

Function Operation Prog. Par

Switching diff. (2-point control)

RP1
Default: filling with energized relay:
Inversion=OFF, RP2
over RP1 relay will be de-energized below RP2 energized t RP1,RP2
Inversion of the operation with change over of RP1 and RP2
or with selection of Inversion=ON Energised
Relay
De-energised

ALARM low
RP1
Default: Inversion=OFF
Below RP1 relay will be de- energized
t RP1
Inversion of the operation (below RP1 relay will be energized
with selection of Inversion=ON Energised
Switching difference = 2.5% of RP1 Relay
De-energised

39
users1

ALARM low with delayed switching

RP1
Default: Inversion=OFF
below RP1 relay will be de- energized
with 0 sec delay t RP1, RP3
Delay can be set under RP3 in sec
Energised
Relay K K K Delay
De-energised

ALARM high
RP1
Default: Inversion=OFF
over RP1 relay will be de- energized
Inversion of the operation (over RP1 relay will be energized t RP1
with selection of Inversion=ON
Switching difference = 2.5% of RP1 Energised
Relay
De-energised

ALARM high with delayed switching

RP1
Default: Inversion=OFF
over RP1 relay will be de- energised with 0 sec delay
Delay can be set under RP3 in sec t RP1, RP3

Energised
Relay K K K Delay
De-energised

Window comparator
RP1
Default: Inversion=OFF
Within the range of RP1..RP2 relay will be energised RP2 RP1, RP2
Inversion of the operation (within the range of RP1..RP2 relay t
will be de-energised) with selection of Inversion=ON
Energised
Relay
De-energised

40
users1

Window D comparator with delayed switching

RP1
Default: Inversion=OFF
Within the range of RP1..RP2 relay will be energised with 0 sec delay RP2
Inversion of the operation t RP1, RP2,
(Within the range of RP1..RP2 RP3
relay will be de-energised ) with selection of Inversion=ON Energised
K K K K K Delay
Relay De-energised

Error
Default: Inversion=OFF RP3
In case of error relay will be de-energised. RP3=0 with any error RP3=n with error of n code
Inversion of the operation (in case of error relay will be energised ) with selection of Inversion=ON

Temperature Temp
RP1
Default: Inversion=OFF
RP1 over temperature of relay will be de-energised
Inversion of the operation (over temperature of RP1relay will be t RP1
energised ) with selection of Inversion=ON
Switching difference = 2.5% of RP1 Energised
Relay
De-energised

Temperature W (window comp) Temp

RP1
Default: Inversion=OFF
Within the range of RP1..RP2 relay will be energised RP2
Inversion of the operation: (within the range of RP1..RP2 relay t RP1, RP2
will be de-energised) with selection of Inversion=ON
Energised
Relay
De-energised

41
users1

Impulse C Energised
Default: Inversion=OFF Relay 200 ms
relay will be energised for appr. 200ms in 0 intervals De-energised RP3
Inversion of the operation with selection of Inversion=ON RP3 [sec]
Interval can be set under RP3 in sec
TOT1 RP3=10
Impulse F
Default: Inversion=OFF 20
relay will be energised for appr. 200ms with each amount of flow 10 RP3
set under RP3 (default=0) t
Inversion of the operation with selection of Inversion=ON
Energised
Relay
De-energised
TOT1 RP1=20
TOT1
Default: Inversion=OFF 20
relay will be de-energised when TOT1 reaches value of RP1 RP1
Inversion of the operation (relay will be energised) with selection of t
Inversion=ON
Energised
Relay
De-energised

42
users1

Alt S (optimised pump control) RP1

Default: Inversion=OFF R3
More relays assigned to one source (transmitter) so that the number RP2 RP1
of switching-on will be the same for all relays. R2
Relays connected in series will be energised and de-energised RP1 RP2
one after the other irrespectively of fulfilment of the condition R1
RP2
Relays programmed for this work would operate in the following
sequence for Switching diff t
3 31 32 2 21 energized RP1, RP2
123 2 12 1 1 De- energized Energised
In case of Alt sequence for energizing and de-energizing will be Relay R3
123-123. De-energised
Energised
Relay R2
De-energised
Energised
Relay R1
De-energised
1 23 12 3 12 Energised
123 1 23 1 2 De-energised

43
users1

Notes:

1. Parameter are to program in the Main menu/Relays/Relay/Program/Parameter menu table by going to the relevant
Parameter 23 parameter with entering value in between pointers and clicking OK. Programming parameters can only be completed
RP1 = 0001.25 with clicking OK after setting RP3 (even if it is zero or not applicable in the given function!)
RP2 = 12.45
RP3 = 0

2. Inactive relays are de-energised (See: Main menu/Relays).

3. More than one device can be assigned to any of the relays (Main menu/Relays/Program/Source)
The result will be the mathematical combination of sources marked with + or signed in the menu point Source.
If the measurement mode or dimension of devices are different MultiCONT will send error message Program (See 6. Errors, Error messages)
The result of the transmitters marked with are added.
The result of the transmitters marked with is deducted from that result of the transmitters marked with are added.
Computes the average of the results of the transmitters marked with
The instrument indicates error if the dimension or the measurement mode of the transmitters is different.
4. If RP1=RP2 in operation mode Switching diff relay will operate according to ALARM low
5. If RP1=0 in operation mode ALARM low relay will always be energized
6. If RP1=0 in operation mode ALARM high relay will always be de- energized
7. Error Program will be indicated (See 6. Error, Error messages, ) if
in operation mode Impulse F more than one source is assigned too
RP3=0 in operation mode Impulse F or Impulse C 0
8. If Error function selected no (source) assignment is required since errors of all devices will be monitored.
9. Relay state will not be changed if its source does not reply!

For a detailed overview of the Programming s. Appendix 3.

44
users1

5.8. CURRENT GENERATOR CONFIGURATION

First of all current generators should be assigned to a field device, which will be performed in the menu point
Main menu / Relays / Program / Current generator.
The result of the transmitters marked with are added.
The result of the transmitters marked with is deducted from that result of the transmitters marked with are added.
Computes the average of the results of the transmitters marked with
Secondly relevant function is to select in the menu point Main menu/Relays/Program/Function. Finally parameters have to be programmed i.e. values of the
switching points P1 and P2 entered in dimensions defined by the Measurement Mode of the field device to which the current generators has been assigned.
Thus if the measurement mode is LEVEL [m] (e.g. with a device of SE-300 i.e. P01=x1 P00=00x), switching points have to be entered in LEVEL [m].
Operation of the current generator can also be assigned to the difference value of two devices or to the average of more devices. For overview see Menu
system of the MultiCONT Appendix 4. The functions of the current generators in detail are as below.

FUNCTION OPERATION PROG.PAR.

Current output is proportional to the primary measured value selected in the
Analogue Output device (DIS, LEV, VOL, FLOW, etc.) CP1,CP2
CP1 is assigned to 4mA, CP2 is assigned to 20mA.
Error 3.6mA CP3=0 current output will be provided with any error
CP3=n current output will be provided in case of error with code n For error CP3
Error 22mA codes see 6. Error codes
During trouble free operation the current output is 4mA

Menue:
Program :
1. Programming error will be indicated if in analogue output operation mode CP1=CP2 and output current will not change
2. Value of the output current will not change if the unit assigned does not answer!
3. If the current output is not activated the output will be 0 mA.
4. If Error function selected no (source) assignment is required since errors of all devices will be monitored
5. The programmed parameters can only be saved at C3 by pressing OK.

45
 users1
5.9. SWITCHING ON
MultiCONT

displayed. The procedure takes about 50s and it can be accelerated by click on ESC (time approximately 25 s).
On powering a test program checking the hardware of MultiCONT will be run that can be followed on the screen by the (English) messages
System check In case of error CODE ERROR
message provided
Testing CODE and restart
RESTARTING

System check
CODE OK

In case of no FLASH
System check NONE FLASH
message provided
Testing FLASH and restart RESTARTING

In case of incorrigible FLASH ERROR

FLASH error RESTARTING

46
In case of corrigible FLASH ERROR
FLASH error, repair PAGE: nnnn

System check
FLASH OK

Messages depending on VARIABLE ERROR

Init variables The error: RESTARTING

error DEVICE ERROR

in the list of devices RESTARTING

error ROUTE ERROR

in the list of routes RESTARTING

error in the list of CURRENT ERROR

current generators RESTARTING

error RELAY ERROR

No error in the list of relays RESTARTING
users1

Since parameters necessary for the trouble free operation are stored in the FLASH in case of FLASH error the unit
should be sent to the service.
After the successfully completed test polling and query will be performed on the basis of the previous configuration
and the MultiCONT will enter Measurement Mode and it will work in accordance with setting of 5.4 Main
menu/MultiCONT config (See 5.10 Measurement Mode)

1: - - - - - - - - DIST M
There is no response from device no. 1. (there is no result to display)
Error Response can be red in the error list.
2 Errors: 1

2: SE300-11 DIST M
The result of the device no. 2. is on the display.
3.125 m Device no. 1. Is under asking.
1

47
users1

5.10. MEASUREMENT MODE

After the successfully completed test following the switch-on the MultiCONT will List tag (Short TAG) Measurement Measurement
automatically enter the Measurement Mode. Measurement values will be queried and 1...9, max. 8 character mode screen
A...F
displayed in accordance with the device list and settings of
5.4 Main menu /MultiCONT config. In the upper row list-tag (1,9,A.,...F). and Short n: SE300-11 LEV M
TAG abbreviation of the measurement (DIST, LEV, VOL, etc.), in the middle
measurement value and dimension, bargraph, in the bottom row list-tag of the unit
being under query, number of errors as well as state of the access lock is displayed.
5.486 m bargraph

Beyond the Measurement Image, User Images, relaydevice, current generator-device m Errors: 2 CLOSED
assignment and error list can be viewed in this operation mode (See Attachment 5). List tag of Protection switch
Beyond the Measurement Image, User Images (Range, Dual, Difference and queried device of settings closed
Average) can also be selected here. (See 5.4 Main menu/MultiCONT config/Users
image.) During programming full scale of operation such as polling of devices, function Error messages can be erased with key
of relays and current generators will be maintained. If the MultiCONT is left in
Programming Mode by mistake, it will automatically return to measurement after 5
minutes following the last clicking on any key.

The relay-device and current generator devise coupling can be seen in this measurement mode.

See Appendix 5.

Even if a possible error does not exists any more, it will be displayed at the given instrument until it is confirmed (ESC). Beside the standard display mode, other
ones can also chosen (Bargraph, Double, Difference, Average) s. 5.4. Main Menu/MultiCONT config/User display.
Measuring, asking the devices and controlling the relays and the current generators are carried on also during programming . If the instrument remains
accidentally in programming mode, it returns automatically after 5 sec to measurement mode. The MultiCONT saves the number of switches and the working
hours.

48
users1

6. ERRORS, ERROR MESSAGES, ERROR CODES

In case of failure (blinking) error message appears immediately on the Measurement image even if the error does not occur to the transmitter being on the
screen. (See M image above) Failures will be collected in the Error list with list number of the error, short TAG and description of the failure. After ceasing of
possible error it should be erased from the list by going to the relevant row and pressing ESC. Thus for instance relay set for function Error will indicate error
even after correction of failure until the error is confirmed as above.

ERROR CODE MESSAGE ERROR DESCRIPTION CORRECTION

1 Init Device does not reply after switching-on* Check wiring of device
2 Answer Device with normal operation fail to provide replies ** Check wiring of device
3 Sensor Sensor failure on the device *** Check device (transmitter)
Check programming of device ( See relevant Install and Prog. Manual), and
4 Device Other device failure
measurement conditions
Error occurred during programming of relay or current
5 Program Check programming
generator ****
6 Save Error occurred in the course of saving in the memory Send device to the service by repeated occurrence.

* Device, being on the list and activated does not reply after switching-on. Possible reasons:
- network has been modified before re-powering (device was disconnected, wiring changed, etc.)
- device failed to reach operation conditions (not able to provide measurement results) e.g. STD-300 can not measure until amplification reaches
operation conditions..

** Device with normal operation fail to provide replies. Possible reasons:

- breaking down of device
- broken cable
- noisy HART line (See Main menu/MultiCONT config/HART test)

49
users1

*** Special indication belongs to the failure of the sensors. This information appears on breaking down of the transducer in the ultrasound transmitter
or cracking of the magnet disc, break of the magnetostrictive wire in the magnetostrictive transmitter. On the other hand this is the message
displayed when echo loss condition occurs with the ultrasonic measurement.

1: SE300-12 DIST M

SENSERR The device answers but there is no valid result because of sensor error.

2 Errors: 1

**** Programming error will be caused:

- assignment of sources with different measured values and/or with different dimension to a relay or current generator
- current generator programmed to analogue output and CP1=CP2
- assignment of (Impulse F) relay to flow and there are more than one source
- assignment of (Impulse F) relay to flow and RP3=0

50
users1

7. PROTECTION OF SETTING BY HARDWARE

Protection switch can be accessed after loosing nuts fastening the

front panel.

The switch for protection of settings in its ON position will hinder

modification of parameters effecting operation of the MultiCONT
such as:
S1
- relay parameters
- current generator parameters
- involving activation of devices
IC2 - remote programming
- refusing access to Service menu
- refusing access to the menus DEV detect, EXT detect
and Strategy under MultiCONT config

The switch is not influencing changes not effecting operation of the

OFF ON MultiCONT such as language, backlight, user image, etc)

51
users1

8. REPLACING FUSE

Loosen four nuts, which are fastening the front panel. Tilt forward the

PRW10A02-A
+
front panel carefully, in order not to span cable band and replace the
fuse.

MultiCONT has one fuse the value of which depends on the

CURRENTG1
power supply

CURRENTG2
PRWTAP

RS485
POWER SUPPLY FUSE
Fuse B1 85255 V AC 5060Hz T400mA
10,528 V AC 5060Hz
10,540 V DC T1A

Warning!
Only fuses as per the table above can be used
for replacement.

52
users1

APPENDIX 1. THE ID IDENTIFICATION CODES OF THE MANUFACTURERS

1 "Acromag", 57 "Promac", 113 "Apparatebau Hundsbach",
2 "Allen Bradley", 58 "Exac Corporation", 114 "Dynisco",
3 "Ametek", 59 "Meggitt Mobrey", 115 "Spriano",
4 "Analog Devices", 60 "Arcom Control System", 116 "Direct Measurement",
5 "Elsag Bailey", 61 "Princo", 117 "Klay Instruments",
6 "Beckman", 62 "Smar", 118 "Action Instruments",
7 "Bell Microsensor", 63 "Foxboro Eckardt", 119 "MMG Automatiky DTR",
8 "Bourns", 64 "Measurement Technology", 120 "Buerkert Fluid Control Systems",
9 "Bristol Babcock", 65 "Applied System Technologies", 121 "AALIANT Process Mgt",
10 "Brooks Instrument", 66 "Samson", 122 "POUNDS INSTRUMENT",
11 "Chessel", 67 "Sparling Instrumnets", 123 "ZAP S.A. Ostrow Wielkopolski",
12 "Combustion Engineering", 68 "Fireye", 124 "GLI",
13 "Daniel Industries", 69 "Krohne", 125 "Fisher-Rosemount Performance
14 "Delta", 70 "Betz", Technologies",
15 "Dieterich Standard", 71 "Druck", 126 "Paper Machine Components",
16 "Dohrmann", 72 "SOR", 127 "LABOM",
17 "Endress & Hauser", 73 "Elcon Instruments", 128 "Danfoss",
18 "Elsag Bailey", 74 "EMCO", 129 "Turbo",
19 "Fisher Controls", 75 "Termiflex Corporation", 130 "TOKYO KEISO",
20 "Foxboro", 76 "VAF Instruments", 131 "SMC",
21 "Fuji", 77 "Westlock Controls", 132 "Status Instruments",
22 "ABB Automation", 78 "Dexelbrook", 133 "Huakong",
23 "Honeywell", 79 "Saab Tank Control", 134 "Duon Systems",
24 "ITT Barton", 80 "K-TEK", 135 "Vortek Instruments, LLC",
25 "Kay Ray/Sensall", 81 "Flowdata", 136 "AG Crosby",
26 "ABB Automation", 82 "Draeger", 137 "Action Instruments",
27 "Leeds & Northrup", 83 "Raytek", 138 "Keystone Controls",
28 "Leslie", 84 "Siemens Milltronics PI", 139 "Thermo Electric Co.",
29 "M-System Co.", 85 "BTG", 140 "ISE-Magtech",
30 "Measurex", 86 "Magnetrol", 141 "Rueger",
31 "Micro Motion", 87 "Metso Automation", 142 "Mettler Toledo",
32 "Moore Industries", 88 "Milltronics", 143 "Det-Tronics",
33 "Moore Products", 89 "HELIOS", 144 "TN Technologies",
34 "Ohkura Electric", 90 "Anderson Instrument Company", 145 "DeZURIK",
35 "Paine", 91 "INOR", 146 "Phase Dynamics",
36 "Rochester Instrument Systems", 92 "ROBERTSHAW", 147 "WELLTECH SHANGHAI",
37 "Ronan", 93 "PEPPERL+FUCHS", 148 "ENRAF",
38 "Rosemount", 94 "ACCUTECH", 149 "4tech ASA",
39 "Peek Measurement", 95 "Flow Measurement", 150 "Brand Instruments",
40 "Schlumberger", 96 "KAMSTRUP", 151 "NIVELCO",
41 "Sensall", 97 "Knick", 152 "Camille Bauer",
42 "Siemens", 98 "VEGA", 153 "Metran",
43 "Weed", 99 "MTS Systems Corp.", 154 "Milton Roy Co.",
44 "Toshiba", 100 "Oval", 155 "PMV",
45 "Transmation", 101 "Masoneilan-Dresser", 156 "Turck",
46 "Rosemount Analytic", 102 "BESTA", 157 "Panametrics",
47 "Metso Automation", 103 "Ohmart", 158 "Stahl",
48 "Flowserve", 104 "Harold Beck and Sons", 159 "Analytical Technology Inc.",
49 "Varec", 105 "Rittmeyer Instrumentation", 160 "Fieldbus International",
50 "Viatran", 106 "Rossel Messtechnik", 161 "BERTHOLD",
51 "Delta/Weed", 107 "WIKA", 162 "InterCorr",
52 "Westinghouse", 108 "Bopp & Reuther Heinrichs", 163 "China BRICONTE Co Ltd",
53 "Xomox", 109 "PR Electronics", 164 "Electron Machine",
54 "Yamatake", 110 "Jordan Controls", 165 "Sierra Instruments",
55 "Yokogawa", 111 "Valcom s.r.l.", 166 "Fluid Components Intl",
56 "Nuovo Pignone" 112 "US ELECTRIC MOTORS",

53
 users1
APPENDIX 2.
Measurement value User display Relay coupling 4-20 mA coupling Error report

1: ST300 LEV M 123456789ABDC DEF R 123456789A BDCDE F C Error report 6E Device: SE300 607 Remote program 6 08 Parameters 6 11
Switching ON
R1 C1 01: SE300-11: Vlasz Remote program Secret unlock
Test (can be accelerated
with "ESC")
1.23 m See 5.5 section
R2 C2 02: ST300 : Program Short TAG Secret mod. Device programming
R3 Polling address Parameters

MULTICONT PRW-100 MENU SYSTEM

Message Save in P+C to TMP
Descriptor Send TMP to DEV
Date: Linear. table
Final ass. number Echo
2: ST300 LEV M
Factor ID Clear TOT1
4.76 m Device type ID
SW revision
Clear TOT2

HW revision
Device ID Program 20 Source 21
Major revision Source 1: SE300
Devices 06
Device revision Mode 2: SC380
or if no key is pressed within 5 min. 01: SE300
Parameter :
the instrument returns automatically 02: ST300
Invert n: ST300-1
to measurement mode. :
Test
15: SC300
n: ST300 LEV M
Cycle 25 Mode 22
12.45 ft Hyst
002568 Alarm low
Relay 19 Alarm low, K
Program Alarm high
Cycle count Alarm high, K
Relays 18 Working
: hour Working hour 25
Window
01: R1 Short TAG Window, D
02: R12 ID 001856
Error

54

:
Temp
12: R12n
Password 200 Entering the service menu: Temp, W
Press the keys at the Main menu Short TAG 25 Pulse, C
05
0000000 same time by switching ON and Pulse, F
Devices
R132-HCL TOT1
enter the password. Relays
Current generator Alt..S
MultiCONT config
Service 6 201 Save config ID 25 Parameter 23
Default Load config RP1 = 0003.45
Default config Current generator 27
PSW CLR 402568 RP2 = 12.45
Reset 01: I1
Stime CLR RP3 = 0
02: I2
Power CLR
:
Device NUM
12: I2n Current gen.: I2 28 Program 29 Source 30
Relay NUM Keys:
Relay (I) NUM Program Source 1: SE300
Keys for changes menu: Short TAG Mode 2: SC380
Current NUM
Current (I) NUM Keys for menu navigation: ID Parameter
: :
U485 (I) NUM Activating: Test n: ST300-1
EXT num MultiCONT config 6 35
Current CAL DEV detect Strategy 42
Legend: P by P
Relay test EXT detect Short TAG 34 Mode 31
Not active Strategy Higher 1st
Current test Primary
Button test Active, relay is energised by assignment User display Fixed R132-HCL Error 3.6 mA
Display test Assignes with positive sign as source Display mode Error 22 mA
SW test Assignes with negative sign as source Password
N485 test Assignes to average calculation as source Language User display 51
U485 test MultiCONT addr. None
F232 test Back light Bargraph ID 34 Parameter 32
HART test HART debug Double CP1 = 0003.45
HOST mode Report Difference 402568 CP2 = 12.45
Save+Reset Flash fresh Average CP3:= 0
 users1
APPENDIX 3.
Main menu 05 Relays 18 Relay 19 Programming 20 Source 21 Not assigned with sign
Devices 01: R1 Programming Source 1: SE300 Assigned with "+" sign
Relays 02: R12 Cycle Function 2: SC380 Assigned with "" sign
Current generator : Working
: hours Parameter
: : Assigned, averaged
Local config 12: R12n Short TAG Invert n: ST300-1 Modify with
Save config ID Test

PROGRAMMING THE RELAYS

Load config
Default Relay Relay identification
Cycle 25 Mode 22 Not selected
Restart no. Short TAG
Hyst Selected
Active 002568 Alarm low Selection with
Not active (relay is de-energised) Alarm low, K
Alarm high
Alarm high, K
Working hours 25
Window
Window, D
001856
Error
Temperature
Temperature, W
Change with
Short TAG 25 Impulse, C
Impulse, F
keys
R132-HCL TOT

55

Escape with
Alt..S
Validate with

This parameter can be changed

ID 25 Parameter 23
Positioning the decimal point
RP1 = 0003.45
Changing the sign and the number
402568 RP2 = 12.45
Returning to menu
RP3:= 0
"Programming" by P1
Returning to the former parameter
by P2 and P3
Invert 26
Accepting the parameter and
Figyelem! Not selected On
skipping to the next one.
A bellts csak abba a memriba kerl be, amelyik a mkdst Selected Off
Pressing it by P3 P1...P3 will be
befolysolhatja. Ennek tartalma kikapcsolskor elvsz. Selection with keys
saved and the programme returns
Ments "Main menu" / "Ments" menpontban -val It will be valid immediatelly after action
to the menu "Programming"
Saving by "Main menu / Save"
Test 24
Not selected On
Selected Off
Selection with keys Toggle
The relay state changes immediatelly after selection.
 users1
APPENDIX 4.
Main menu 05 Current generators 27 Current gen.: I2 28 Programming 29 Source 30 Not assigned with sign
Devices 01: I1 Programming Source 1: SE300 Assigned with "+" sign
Relays 02: I2 Short TAG Function 2: SC380 Assigned with "" sign
Current generators : ID Parameter
: : Assigned, averaged
MultiCONT config 12: I2n Test n: ST300-1 Modify with
Save config

PROGRAMMING THE CURRENT GENERATOR

Load config
Default Current Current gen. identification
Mode 31 Not selected
Restart generator no. Short TAG
Primary Selected
Active Error 3.6 mA Selection with
Not active Error 22 mA
(output current 0 mA)

Change with This parameter can be changed

Short TAG 34 Parameter 32
Positioning the decimal point
CP1 = 0003.45 Changing the sign and the number
keys
Escape with
R132-HCL CP2 = 12.45 Returning to menu
Validate with
CP3:= 0 "Programming" by P1
Returning to the former parameter
by P2 and P3
Accepting the parameter and

56

skipping to the next one.

Pressing it by P3 P1...P3 will be
saved and the programme returns
to the menu "Programming"
Saving by "Main menu / Save"

ID 34 Test 33
Change with
402568 18.565 Changed immediatelly
Figyelem!
A bellts csak abba a memriba kerl be, amelyik a mkdst
befolysolhatja. Ennek tartalma kikapcsolskor elvsz.
Ments "Main menu" / "Ments" menpontban -val
 users1
APPENDIX 5.
Switching ON
Test (can be accelerated
with "ESC")

MEASUREMENT MODE
Number
of the device
Measurement value User's image Relay assignment 4-20 mA assignment Error report

1: SE300-11 DIST M 123456789ABDCD EF R 123456789ABDCDEF C Error report 6E

R1 C1 01: SE300-11: Response
3.125 m See 5.5
R2 C2 02: ST300 : Programme
2 Errors: 2 CLOSED R3

Serial number of relay Serial number of current Description of error

Identification of device
Number of error
No assignment No assignment
Assigned (de-energised) Assigned

57

Assigned (energised) Confirming the errors with

Scrolling with Scrolling with
Errors: s. 5. Ch. 6.

List tag (Short TAG) Measurement Measurement

1...9, max. 8 character mode screen
A...F

n: SE300-11 LEV M Main menu 6 05

Devices Enter the "Main menu" with
5.486 m bargraph
Relays Escape to "Main menu" with
m Errors: 2 CLOSED Current generator

List tag of Protection switch

queried device of settings closed

Error messages can be erased with key