AX-492/592/892 Natural Sound Stereo Amplifier

Amplificateur stro de la srie Natural Sound

Thank you for selecting this YAMAHA stereo amplifier.

Nous vous remercions davoir port votre choix sur cet amplificateur stro YAMAHA.

OWNERS MANUAL
MODE DEMPLOI
 SAFETY INSTRUCTIONS
7 Wall or Ceiling Mounting The unit should be mounted to
CAUTION a wall or ceiling only as recommended by the
manufacturer.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
8 Ventilation The unit should be situated so that its
location or position does not interfere with its proper
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE.
ventilation. For example, the unit should not be situated
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. on a bed, sofa, rug, or similar surface, that may block the
ventilation openings; or placed in a built-in installation,
such as a bookcase or cabinet that may impede the flow
of air through the ventilation openings.
Explanation of Graphical Symbols
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert you to the 9 Heat The unit should be situated away from heat
presence of uninsulated dangerous voltage within the sources such as radiators, stoves, or other appliances
products enclosure that may be of sufficient magnitude that produce heat.
to constitute a risk of electric shock to persons.

10 Power Sources The unit should be connected to a

The exclamation point within an equilateral triangle is power supply only of the type described in the operating
intended to alert you to the presence of important
operating and maintenance (servicing) instructions in instructions or as marked on the unit.
the literature accompanying the appliance.
11 Power-Cord Protection Power-supply cords should be
routed so that they are not likely to be walked on or
WARNING pinched by items placed upon or against them, paying
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO particular attention to cords at plugs, convenience
NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. receptacles, and the point where they exit from the unit.

IMPORTANT! 12 Cleaning The unit should be cleaned only as

Please record the serial number of this unit in the space recommended by the manufacturer.
below.
Model: 13 Nonuse Periods The power cord of the unit should be
Serial No.:
unplugged from the outlet when left unused for a long
The serial number is located on the rear of the unit. period of time.
Retain this Owners Manual in a safe place for future
reference.
14 Object and Liquid Entry Care should be taken so that
objects do not fall into and liquids are not spilled into the
inside of the unit.
1 Read Instructions All the safety and operating
instructions should be read before the unit is operated. 15 Damage Requiring Service The unit should be serviced
by qualified service personnel when:
2 Retain Instructions The safety and operating instructions
should be retained for future reference. A. The power-supply cord or the plug has been
damaged; or
3 Heed Warnings All warnings on the unit and in the B. Objects have fallen, or liquid has been spilled into the
operating instructions should be adhered to. unit; or
C. The unit has been exposed to rain; or
4 Follow Instructions All operating and other instructions D. The unit does not appear to operate normally or
should be followed. exhibits a marked change in performance; or
E. The unit has been dropped, or the cabinet damaged.
5 Water and Moisture The unit should not be used near
water for example, near a bathtub, washbowl, kitchen
sink, laundry tub, in a wet basement, or near a swimming 16 Servicing The user should not attempt to service the unit
pool, etc. beyond those means described in the operating
instructions. All other servicing should be referred to
qualified service personnel.
6 Carts and Stands The unit should be used only with a
cart or stand that is recommended by the
manufacturer. 17 Power Lines An outdoor antenna should be located
away from power lines.

6A A unit and cart combination should be

moved with care. Quick stops, excessive 18 Grounding or Polarization Precautions should be taken
force, and uneven surfaces may cause so that the grounding or polarization is not defeated.
the unit and cart combination to overturn.

2
 English
FCC INFORMATION

1. IMPORTANT NOTICE : DO NOT MODIFY THIS UNIT! Compliance with FCC regulations does not guarantee that
This product, when installed as indicated in the interference will not occur in all installations. If this product
instructions contained in this manual, meets FCC is found to be the source of interference, which can be
requirements. Modifications not expressly approved by determined by turning the unit OFF and ON, please try
Yamaha may void your authority, granted by the FCC, to to eliminate the problem by using one of the following
use the product. measures:
2. IMPORTANT : When connecting this product to Relocate either this product or the device that is being
accessories and/or another product use only high quality affected by the interference.
shielded cables. Cable/s supplied with this product
MUST be used. Follow all installation instructions. Utilize power outlets that are on different branch (circuit
Failure to follow instructions could void your FCC breaker or fuse) circuits or install AC line filter/s.
authorization to use this product in the USA. In the case of radio or TV interference, relocate/reorient the
3. NOTE : This product has been tested and found to antenna. If the antenna lead-in is 300 ohm ribbon lead,
comply with the requirements listed in FCC Regulations, change the lead-in to coaxial type cable.
Part 15 for Class B digital devices. Compliance with If these corrective measures do not produce satisfactory
these requirements provides a reasonable level of results, please contact the local retailer authorized to
assurance that your use of this product in a residential distribute this type of product. If you can not locate the
environment will not result in harmful interference with appropriate retailer, please contact Yamaha Electronics
other electronic devices. Corp., U.S.A. 6660 Orangethorpe Ave, Buena Park, CA
This equipment generates/uses radio frequencies and, if 90620.
not installed and used according to the instructions
found in the users manual, may cause interference The above statements apply ONLY to those products
harmful to the operation of other electronic devices. distributed by Yamaha Corporation of America or its
subsidiaries.

We Want You Listening For A Lifetime (for US customers only)

YAMAHA and the Electronic Industries Associations Since hearing damage from loud sounds is often
Consumer Electronics Group want you to get the most out of undetectable until it is too late, YAMAHA and the
your equipment by playing it at a safe level. One that lets the Electronic Industries Associations Consumer
sound come through loud and clear without annoying blaring Electronics Group recommend you to avoid
or distortion and, most importantly, without affecting your prolonged exposure from excessive volume levels.
sensitive hearing.

3
 CONTENTS FEATURES
Supplied accessories .....................................................4 AX-492 85W + 85W (8) RMS Output Power,
Connections ...................................................................6 0.019% THD, 2020,000 Hz
Controls and their functions ..........................................12 AX-592 100W + 100W (8) RMS Output Power,
Remote control .............................................................14 0.015% THD, 2020,000 Hz
Basic operations ...........................................................16 AX-892 115W + 115W (8) RMS Output Power,
Troubleshooting ............................................................20 0.015% THD, 2020,000 Hz
Specifications ...............................................................21
High Dynamic Power, Low Impedance Drive Capability
Continuously Variable Loudness Control
CD DIRECT AMP switch: used to reproduce the purest
CD sound
PURE DIRECT switch: used to reproduce the purest
source sound
SUBSONIC FILTER switch; used to eliminate undesirable
ultra-low-frequency signals (AX-592 and AX-892 only)
PRE OUT/MAIN IN terminals; useful for connecting an
equalizer, sound processor, etc. (AX-592 and AX-892
only)
Remote control capability

Supplied accessories After unpacking, check that the following accessories are included.

Remote Control Transmitter Batteries (size AA, R6, UM-3)

YAMAHA HiFi SYSTEM YAMAHA HiFi SYSTEM

REMOTE CONTROL TRANSMITTER REMOTE CONTROL TRANSMITTER

AUX AUX

DIR A DIR B REC/PAUSE PLAY TAPE 2 DIR A DIR B REC/PAUSE PLAY TAPE 2

TAPE 1 A/B TAPE 1

A/B

TUNER PRESET A/B/C/D/E TUNER

PRESET A/B/C/D/E

DISC PLAY CD DISC PLAY CD

PLAY
/CUT PHONO PHONO

POWER VOLUME POWER VOLUME

AX-592/892 AX-492

4
 English
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.
1. To assure the finest performance, please read this manual 13. Voltage Selector (General Model only)
carefully and keep it in a safe place for future use. The voltage selector on the rear panel of this unit must be set
for your local main voltage before plugging into the electrical
2. Install this unit in a cool, dry and dust-free area. Do not place it in outlet.
direct sunlight or near sources of heat (e.g., a stove, etc.). Make Voltages are 110/120/220/240 V AC, 60/50 Hz.
sure that it is well ventilated and not exposed to rain or moisture
and that it is on a flat, stable surface, free from vibration. WARNING
To reduce the risk of fire or electric shock, do not expose the unit to
3. Never open the cabinet. If something drops into the unit, contact rain or moisture.
your dealer.
IMPORTANT
4. When moving the unit, first disconnect the AC power plug and the The serial number is located on the rear panel.
cables which are connected to other equipment. Never pull the Please record the serial number of this unit in the space below.
cables or use excessive force on switches or controls. Serial No.:
5. The openings on the cabinet assure proper ventilation of the unit. Keep this Owners Manual in a safe place for future use.
If these openings are obstructed, the temperature inside the
cabinet will rise rapidly, damaging the unit or causing a fire. Avoid Note
blocking the ventilation openings and make sure that the unit is The unit is not disconnected from the AC power source as long as it
well ventilated. Allow at least 30 cm (12 in) of space above the is connected to the electrical outlet, even if the unit itself is turned
unit and 20 cm (8 in) of space on the sides and rear. off.

6. Always set the VOLUME control to before playing the source.

Increase the volume gradually to a desired level after the source CAUTION (FOR CANADA MODEL)
has started playing. TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF
PLUG TO WIDE SLOT AND FULLY INSERT.
7. Use a clean, dry cloth to clean the unit. Do not use chemical
solvents which might damage the finish. FOR CANADIAN CUSTOMERS
THIS CLASS B DIGITAL APPARATUS MEETS ALL
8. Be sure to read the TROUBLESHOOTING section before REQUIREMENTS OF THE CANADIAN INTERFERENCE-
deciding that the unit is faulty. CAUSING EQUIPMENT REGULATIONS.

9. When not planning to use this unit for long periods of time (e.g.,
vacation, etc.), disconnect the AC power plug from the electrical
outlet.

10. To prevent damage from lightning, disconnect the AC power plug

and antenna cable when there is an electrical storm.

11. Make sure that the unit is always properly grounded and
polarized.

12. Do not connect audio equipment to the AC outlet on the rear panel
if the equipment requires more power than the outlet is rated to
provide.

WARNING
Do not change the IMPEDANCE SELECTOR IMPEDANCE
SELECTOR
VOLTAGE SELECTOR

switch setting while the power to this unit is on,

otherwise this unit may be damaged.
IF THIS UNIT FAILS TO TURN ON WHEN THE AC OUTLETS

POWER SWITCH IS PRESSED A OR B : 4 MIN. /SPEAKER

SWITCHIED
100W MAX. TOTAL

The IMPEDANCE SELECTOR switch may not be

A + B : 8 MIN. /SPEAKER

A OR B : 6 MIN. /SPEAKER
A + B :12 MIN. /SPEAKER

set to either end closely. If so, set the switch to

either end closely.
Example: AX-892

<General model>

5
 CONNECTIONS
Before making any connections to or from this unit, first switch it and any other connected components off.
Properly connect this unit and other components, L (left) to L, R (right) to R, + to + and to . Also, refer to the owners
manual of each component which is to be connected to this unit.
If you have YAMAHA components numbered 1, 2, 3, etc. on the rear panel, connections can easily be made by connecting the
output (input) terminals of each component to the same-numbered terminals on this unit.

AX-492
Turntable Tape deck 1 Tape deck 2 Speakers A
LINE OUT

LINE OUT
LINE IN Right Left

LINE IN
+ +
OUTPUT

GND

PHONO
VOLTAGE SELECTOR AC OUTLETS

R L

GND SWITCHIED
1 CD 100W MAX. TOTAL

L
R L A OR B : 4 MIN. /SPEAKER
A + B : 8 MIN. /SPEAKER
R L
R A OR B : 6 MIN. /SPEAKER
A + B :12 MIN. /SPEAKER
A
TAPE REC TAPE REC
2 PB 3 OUT 4 PB 3 OUT 4
TUNER TAPE 1 TAPE 2 AUX
(MD)

CAUTION SEE INSTRUCTION MANUAL FOR CONNECT SETTING

SPEAKERS IMPEDANCE SELECTOR

<General model>
AUDIO OUT

To
OUTPUT

OUTPUT

electrical
outlet

+ +

Right Left

Compact disc player Tuner Video cassette player, Speakers B

LD player, etc.

* For descriptions of the shaded areas, refer to page 10.

6
 English
AX-592
Turntable Tape deck 1 Tape deck 2 Speakers A

LINE OUT

LINE OUT
Right Left
LINE IN

LINE IN
+ +
OUTPUT
GND

SPEAKERS IMPEDANCE
PHONO COUPLER SELECTOR
R L
A
L

R L
MM R
MC
PRE MAIN
OUT IN VOLTAGE SELECTOR

L
R L A OR B : 4 MIN. /SPEAKER
A + B : 8 MIN. /SPEAKER
R L CAUTION SEE INSTRUCTION MANUAL FOR CONNECT SETTING A OR B : 6 MIN. /SPEAKER
1 CD R A + B :12 MIN. /SPEAKER

TAPE REC TAPE REC

2 PB 3 OUT 4 PB 3 OUT 4
GND
TUNER TAPE 1 TAPE 2 AUX
(MD) B

PHONO
100W MAX. TOTAL
REMOTE SWITCHIED
CONTROL AC OUTLETS

<General model>
AUDIO OUT
OUTPUT

OUTPUT

To
electrical
outlet
+ +

Right Left

Compact disc player Tuner Video cassette player, Speakers B

LD player, etc.

* For descriptions of the shaded areas, refer to page 10.

7
 AX-892

Turntable Tape deck 1

LINE OUT Tape deck 2 Speakers A

LINE OUT
Right Left
LINE IN

LINE IN
+ +
OUTPUT
GND

COUPLER SPEAKERS IMPEDANCE VOLTAGE SELECTOR

R CAUTION SEE INSTRUCTION MANUAL FOR CONNECT SETTING L SELECTOR
PHONO PRE MAIN
OUT IN
A
L

R L
R
MM
MC

AC OUTLETS
SWITCHIED
L R L 100W MAX. TOTAL
A OR B : 4 MIN. /SPEAKER
R L B A + B : 8 MIN. /SPEAKER

1 CD R A OR B : 6 MIN. /SPEAKER
A + B :12 MIN. /SPEAKER

TAPE REC TAPE REC

2 PB 3 OUT 4 PB 3 OUT 4
TUNER TAPE 1 TAPE 2 AUX
(MD)
GND

REMOTE
CONTROL

PHONO

<General model>
AUDIO OUT

To
OUTPUT

OUTPUT

electrical
outlet

+ +
Right Left

Compact disc player Tuner Video cassette player, Speakers B

LD player, etc.

* For descriptions of the shaded areas, refer to page 10.

8
 English
CONNECTING SPEAKERS
Connect the SPEAKERS terminals to your speakers with cable One or two speaker systems can be connected to this unit.
of the proper gauge, cut as short as possible. If the speakers If you connect only one speaker system, connect it to either
are improperly connected, no sound will be heard. Connect SPEAKERS A or B terminals.
each speaker making sure that the polarity (+ and ) is correct. Use speakers with the specified impedance shown on the
rear panel.
Red: positive (+)
Black: negative ()

If the cables are reversed, the sound will be unnatural and will
lack bass. Do not allow exposed wires to touch each other
or metal parts; this could damage the unit and speakers.

For AX-492s SPEAKERS A and B terminals and For AX-592s SPEAKERS A terminals only and
for AX-592s SPEAKERS B terminals only: for AX-892s SPEAKERS A and B terminals:

Unscrew the knob.

Insert the exposed wire. 2
[Remove approx. 5 mm
1
(1/4 in) insulation from
2
the speaker wires.]
Tighten the knob and 1
secure the wire. 3

3
Banana plug connections are also possible. Simply insert the
banana plug connector into the corresponding terminal.
(except for UK and Europe models)

Unscrew the knob.

Insert the exposed wire.
[Remove approx. 5 mm (1/4
in) insulation from the
speaker wires.]
Tighten the knob and secure
the wire.

REAR PANEL PARTS

AC OUTLETS (SWITCHED)

Use these to connect the power cords from your components The maximum power (total power consumption of
to this unit. components) that can be connected to the AC OUTLETS
The power to the SWITCHED outlets is controlled by this units (SWITCHED) is 100 watts.
POWER switch or the remote controls POWER key. These
outlets will supply power to the connected components
whenever this unit is turned on.

9
 GND terminal (for turntable use) PRE OUT/MAIN IN terminals AX-592 and AX-892 only
Connecting the ground wire of the turntable to this terminal will Removing the jumper pins enables this unit to independently
normally minimize hum, but in some cases better results may perform the functions of a control amplifier and a power
be obtained with the ground wire disconnected. amplifier. These terminals are for connection of a signal-
processing system such as a graphic equalizer or sound
processor.
If a sound processor or other external unit is connected
between these terminals, the VOLUME control of this unit can
be used for overall adjustment of the sound level.
To connect such a unit, remove the jumper pins from the PRE
OUT/MAIN IN terminals, connect the inputs of that unit to the
REMOTE CONTROL (PHONO) connector PRE OUT terminals and its outputs to the MAIN IN terminals.
For details, refer to the owners manual included with the unit to
AX-592 and AX-892 only
be connected.
If you have a YAMAHA turntable with a terminal for remote
control, connect it to this connector using the cable provided
with the turntable. This connection allows you to control the
turntable with the remote control.
COUP
PRE
LER
OUT MAIN
IN

REMOTE L
CONTROL
R

PHONO PHONO
REMOTE
CONTROL

(AX-592) (AX-892)

Note
PHONO (MM/MC) switch AX-592 and AX-892 only If you will not use the PRE OUT/MAIN IN terminals, never
Select either MM or MC depending on your phono cartridge. If remove the jumper pins. If removed, no sound will be
you use a high-output MC cartridge, select MM. To select MC, output from this unit.
press the switch so that it stays in. To select MM, press the If you will use this unit with an external unit connected
switch again, so that it releases. between the PRE OUT and MAIN IN terminals, make sure
that the CD DIRECT AMP and PURE DIRECT switches on
the front panel are turned off.
MM
MC
If you will use this unit as a power amplifier, connect the
outputs of an external control amplifier, etc. to this units
MAIN IN terminals. In this case, this units controls will not
function, except the PHONES jack and the SPEAKERS
switches, so use the controls on the external control
amplifier to make volume adjustment, etc.

10
 English
IMPEDANCE SELECTOR switch VOLTAGE SELECTOR switch (General model only)
Make sure that the power to the unit is off, before you set the If the pre-set setting is incorrect, set the switch to the proper
switch. voltage for your area.
Select the appropriate setting for your speaker system.
Consult your dealer if you are unsure of the correct setting.
Upper position WARNING
4 : If you use either speaker system A or B, the impedance Be sure to unplug the unit before setting the VOLTAGE
of each speaker must be 4 , or higher. SELECTOR switch.
8 : If you use both speaker systems A and B at the same
time, the impedance of each speaker must be 8 , or 240V
higher.
Lower position
6 : If you use either speaker system A or B, the impedance
of each speaker must be 6 , or higher.
12 :If you use both speaker systems A and B at the same
time, the impedance of each speaker must be 12 , or
higher.

A OR B : 4 MIN. /SPEAKER
A + B : 8 MIN. /SPEAKER

A OR B : 6 MIN. /SPEAKER
A + B :12 MIN. /SPEAKER

WARNING
Do not change the IMPEDANCE SELECTOR switch
setting while the power to this unit is on, otherwise
this unit may be damaged.
IF THIS UNIT FAILS TO TURN ON WHEN THE POWER
SWITCH IS PRESSED
The IMPEDANCE SELECTOR switch may not be set to
either end closely. If so, set the switch to either end
closely.

11
 CONTROLS AND THEIR FUNCTIONS
FRONT PANEL

AX-492
E

CD DIRECT AMP PURE DIRECT

NATURAL SOUND STEREO AMPLIFIER AX-492

1 D
INPUT VOLUME

16
20 12
CD
TAPE 1 TUNER
28 8
0 0 0 FLAT CD TAPE 2 PHONO
POWER 1 1 1 1 1 1 1 TAPE 1 TUNER (MD)
-30db

2 C
2 2 2 2 2 2 2 10 TAPE 2 PHONO
(MD)
3 3 3 3 3 3 3 9 40 4
AUX AUX
4 4 4 4 4 4 4 8
5 5+ 5 5+ L5 5R 5 7
6
60 2
BASS TREBLE BALANCE LOUDNESS REC OUT
0
-db

PHONES SPEAKERS
A B

3 ON OFF

4 5 6 8 9 0 A

AX-592

CD DIRECT AMP PURE DIRECT

NATURAL SOUND STEREO AMPLIFIER AX-592

1 D
INPUT VOLUME

16
20 12
CD
TAPE 1 TUNER
28 8
0 0 0 FLAT CD TAPE 2 PHONO
POWER 1 1 1 1 1 1 1 TAPE 1 TUNER (MD)

C
ON OFF -30db

2
2 2 2 2 2 2 2 10 TAPE 2 PHONO
(MD)
3 3 3 3 3 3 3 9 40 4
AUX AUX
4 4 4 4 4 4 4 8
5 5+ 5 5+ L5 5R 5 7
6
SUBSONIC 60 2
BASS TREBLE FILTER BALANCE LOUDNESS REC OUT
0
-db

PHONES SPEAKERS
A B

3 ON OFF

4 5 6 7 8 9 0 A

12
 English
AX-892
E

CD DIRECT AMP PURE DIRECT

NATURAL SOUND STEREO AMPLIFIER AX-892

1 D
INPUT VOLUME

16
CD 20 12
TAPE 1 TUNER

28 8

2 0 0 0 FLAT CD TAPE 2 PHONO

POWER 1 1 1 1 1 1 1 TAPE 1 TUNER (MD)
ON OFF -30db

C
2 2 2 2 2 2 2 10 TAPE 2 PHONO
(MD)
3 3 3 3 3 3 3 9 AUX AUX 40 4
4 4 4 4 4 4 4 8
5 5+ 5 5+ L5 5R 5 7
6
SUBSONIC 60 2
BASS TREBLE FILTER BALANCE LOUDNESS REC OUT
0
-db

PHONES SPEAKERS
A B MUTING

3 ON OFF ON OFF
B

4 5 6 7 8 9 0 A

1 Remote control sensor 7 SUBSONIC FILTER switch AX-592 and AX-892 only
Receives signals from the remote control. Used to eliminate undesirable ultra-low-frequency signals
caused by turntable rumble or warped records without
2 POWER switch losing sound quality.
Press this switch to turn the power on and off. When the
power is on, the indicator will be illuminated. 8 BALANCE control
*Standby mode <Except for U.S.A. and Canada models> Adjusts the balance of the output volume to the left and right
While the power is on, pressing the POWER key on the speakers to compensate for channel imbalance caused by
remote control switches the unit to the standby mode. (In speaker location or listening room conditions.
this mode, the power indicator on the unit is half-
illuminated.) 9 Continuously variable LOUDNESS control
Used to boost high and low-frequency ranges at low
3 PHONES jack volume. (Refer to page 18.)
When you listen with headphones, connect the headphones
to the PHONES jack and set both SPEAKERS A and B 0 REC OUT selector
switches to OFF. This switch can be used to select a source and send its
signal directly to the REC OUT terminals on the rear panel,
independently of the setting of the INPUT selector. This
PHONES function allows you to record the selected source while
listening to another source.
A INPUT selector
Selects an input source to listen to.
B MUTING switch AX-892 only
Press this switch to temporarily reduce the volume. Press
again to cancel the MUTING function.
C VOLUME control and indicator
Used to raise or lower the volume level. AX-592 and AX-892 only
4 SPEAKERS switches D PURE DIRECT switch
For the desired speaker system(s), set the switch(es) to Press this switch (the indicator lights up) to listen to a
ON. When using only one speaker system, set the other source in the purest possible sound. (Refer to page 19.)
switch to OFF.
5 BASS control E CD DIRECT AMP switch
Press this switch (the indicator lights up) to listen in the
Used to increase or decrease the low-frequency response. purest possible sound from your CD. (Refer to page 19.)
Selecting 0 produces a flat response.
6 TREBLE control
Used to increase or decrease the high-frequency response.
Selecting 0 produces a flat response.

13
 REMOTE CONTROL
The remote control provided with this unit is designed to control all the most commonly used functions of the unit. If the CD player,
tuner, turntable and tape deck connected to this unit are YAMAHA components designed for remote control compatibility, then this
remote control will also control the various functions of those components.

KEY FUNCTIONS

To control this unit

1 Input selector keys
Select an input source.
YAMAHA HiFi SYSTEM
REMOTE CONTROL TRANSMITTER
2 VOLUME +/ keys
AUX
Adjust the volume level.

DIR A DIR B REC/PAUSE PLAY TAPE 2

3 POWER key
1 A/B TAPE 1 Turns the power on and off.
<Except for U.S.A. and Canada models>
PRESET A/B/C/D/E TUNER 1 While the power is on, pressing the POWER key on the
2 DISC PLAY CD remote control switches the unit from the power-on mode
to the standby mode and vice versa. (In this mode, the
3 PLAY
/CUT PHONO
power indicator on the unit is half-illuminated.)
POWER VOLUME

4
To control other components
Identify the remote control keys with your components keys. If
2 the keys are identical, the functions will be the same. If the keys
are different, refer to the components manual for their functions.
3
1 Tape deck keys
Control the tape deck.
DIR A, DIR B, and A/B are applicable only for a dual
tape deck.
For a single tape deck with an automatic reverse

function, pressing DIR A will reverse the direction of the

tape.

2 Tuner keys
Control the tuner.
+: Selects a higher preset station number.
: Selects a lower preset station number.
A/B/C/D/E: Selects a group (A-E) of preset stations.

* The AX-492s remote control does not have a PLAY/CUT 3 CD player keys
key.
Control the compact disc player.
DISC is applicable only for a compact disc changer.

4 PLAY/CUT key AX-592 and AX-892 only

Press PLAY/CUT to lower the pick-up arm and press it
again to raise the arm.

14
 English
Battery installation Remote control operation range

1 Remote control
sensor

Within approximately
6 m (19.7 feet)

Battery replacement 30 30
If you find that the remote control must be used closer to the
unit, the batteries are weak. Replace both batteries with new
ones.
Note
Use only AA, R6, UM-3 batteries for replacement.
Be sure the polarities are correct. (See the illustration inside Note
the battery compartment.) There should be no large obstacles between the remote
Remove the batteries if the remote control will not be used control and the unit.
for an extended period of time. If the remote control sensor is directly illuminated by strong
If batteries leak, dispose of them immediately. Avoid lighting (especially an inverter type of fluorescent lamp etc.),
touching the leaked material or letting it come in contact with it might prevent the remote control from working. In this
clothing, etc. Clean the battery compartment thoroughly case, reposition the unit to avoid direct lighting.
before installing new batteries.

Opening and closing the control door

When using the remote control or when it is not necessary to operate controls inside the control door, close it.
To open the door To close the door

15
 BASIC OPERATIONS
CD DIRECT AMP PURE DIRECT
NATURAL SOUND STEREO AMPLIFIER AX-892

INPUT VOLUME

16
CD 20 12
TAPE 1 TUNER

2 1,6
28 8
0 0 0 FLAT CD TAPE 2 PHONO
POWER 1 1 1 1 1 1 1 TAPE 1 TUNER (MD)
ON OFF -30db
2 2 2 2 2 2 2 10 TAPE 2 PHONO
(MD)
3 3 3 3 3 3 3 9 AUX AUX 40 4
4 4 4 4 4 4 4 8
5 5+ 5 5+ L5 5R 5 7
6
SUBSONIC 60 2
BASS TREBLE FILTER BALANCE LOUDNESS REC OUT
0
-db

PHONES SPEAKERS
A B MUTING

ON OFF ON OFF

(AX-892)
4 7 3

* The AX-492 does not have a SUBSONIC FILTER and MUTING switch.
* The AX-592 does not have a MUTING switch.

PLAYING A SOURCE

1 Turn the control to . 4 Select the speakers to be used.

VOLUME
SPEAKERS
16
20 12 A B

28 8

ON OFF
40 4

60 2

0 * Be sure that the IMPEDANCE SELECTOR switch is

-db
correctly set as explained on page 11.
* If you use two speaker systems, press both the A and B
2 Turn the power on. switches to ON.
* If you listen with headphones, press both the A and B
switches to OFF.
POWER

5 Play the source.

6 Adjust the volume to the desired level.

VOLUME

3 Select the desired input source.

20
16
12
INPUT
28 8

40 4
CD
TAPE 1 TUNER
60 2
TAPE 2 PHONO
(MD)
0
-db

AUX

AX-592 and AX-892 only

7 If needed, adjust the BASS, TREBLE, BALANCE
LOUDNESS, etc. controls. (Refer to page 18.)
* If you select PHONO as an input source, you should make
sure that PHONO (MM/MC) is switched to the correct Note
position. (Refer to page 10.) To turn off the power, press the POWER switch again.

16
 English
CD DIRECT AMP PURE DIRECT
NATURAL SOUND STEREO AMPLIFIER AX-892

INPUT VOLUME

16
CD 20 12
TAPE 1 TUNER

28 8
TAPE 2 PHONO

3
0 0 0 FLAT CD
POWER 1 1 1 1 1 1 1 TAPE 1 TUNER (MD)
ON OFF -30db
2 2 2 2 2 2 2 10 TAPE 2 PHONO
(MD)
3 3 3 3 3 3 3 9 AUX AUX 40 4
4 4 4 4 4 4 4 8
5 5+ 5 5+ L5 5R 5 7
6
SUBSONIC 60 2
BASS TREBLE FILTER BALANCE LOUDNESS REC OUT
0
-db

PHONES SPEAKERS
A B MUTING

ON OFF ON OFF

(AX-892)
1 3,5

* The AX-492 does not have a SUBSONIC FILTER and MUTING switch.
* The AX-592 does not have a MUTING switch.

RECORDING A SOURCE TO A TAPE (OR DUBBING FROM TAPE TO TAPE)

REC OUT selector setting for dubbing tape to tape
1 Select the source to be recorded.
To tape from tape deck 1 to To tape from tape deck 2 to
CD
TAPE 1 TUNER tape deck 2. tape deck 1.
TAPE 2 PHONO
(MD)
AUX CD CD
TAPE 1 TUNER TAPE 1 TUNER
TAPE 2 PHONO TAPE 2 PHONO
(MD) (MD)
AUX AUX

REC OUT

2 Play the source. REC OUT REC OUT

Note
3 Select the source with the INPUT selector and use the If you want to listen to another source while recording,
VOLUME control to make sure that the proper source select it with the INPUT selector.
is selected. VOLUME, BASS, TREBLE, BALANCE, and LOUDNESS

INPUT VOLUME controls and CD DIRECT AMP, PURE DIRECT,

16
SUBSONIC FILTER (AX-592 and AX-892 only) and the
20 12
TAPE 1
CD
TUNER MUTING switch (AX-892 only) have no effect on the
TAPE 2 PHONO
28 8 material being recorded.
(MD)

40 4
AUX

60 2

0
-db

4 Set the tape deck used for recording in the recording

mode.

5 To monitor the sound of the recording, select the tape

deck being used for recording.

INPUT

CD
TAPE 1 TUNER

TAPE 2 PHONO
(MD)

AUX

17
 Adjusting the BALANCE control Selecting the SPEAKER system
Adjusts the balance of the output volume to the left and right One or two speaker systems can be connected to this unit,
speakers to compensate for channel imbalance caused by allowing you to select speaker system A or B, or both.
speaker location or listening room conditions.

0 SPEAKERS
1 1
A B
2 2

3 3

4 4
L5 5R ON OFF

BALANCE
* Be sure that the INPEDANCE SELECTOR switch is correctly
set as explained on page 11.

Adjusting the BASS and TREBLE Adjusting the continuously variable

controls LOUDNESS control
BASS: Turn this control clockwise to increase (or This control provides compensation for the human ears loss of
counterclockwise to decrease) the low-frequency response. sensitivity to high and low-frequency ranges at low volume.
This control is adjustable to retain full tonal range at any
TREBLE: Turn this control clockwise to increase (or
volume level.
counterclockwise to decrease) the high-frequency response.

0 0
1 Set the control to FLAT.
1 1 1 1
2 2 2 2 FLAT
1
3 3 3 3 -30db
2 10
4 4 4 4 3 9
5 5+ 5 5+
4 8
5 7
6
BASS TREBLE
LOUDNESS
Note
Selecting 0 produces a flat response. 2 Set the volume to the highest desired listening level.
VOLUME

16
20 12

28 8

40 4

60 2

0
-db

3 Turn until the desired volume is gained.

FLAT
1
-30db
2 10
3 9

4 8
5 7
6

LOUDNESS

18
 English
Using the PURE DIRECT switch Setting the SUBSONIC FILTER switch
AX-592 and AX-892 only
You can enjoy the purest possible sound from your sources by
setting this switch so that the indicator illuminates. The signals When this switch is set ON, undesirable ultra-low-frequency
bypass the BASS, TREBLE, BALANCE and LOUDNESS signals caused by turntable rumble or warped records can be
controls, the SUBSONIC FILTER switch (AX-592 and AX-892 eliminated without losing sound quality.
only), and the PRE OUT/MAIN IN terminals (AX-592 and AX-
892 only), eliminating any alterations to the signals.

ON OFF
PURE DIRECT

SUBSONIC
FILTER

Using the CD DIRECT AMP switch Using the MUTING switch

AX-892 only
For the best CD sound, set this switch so the indicator
illuminates. The CD input signal is sent to a separate circuit, Selecting ON temporarily reduces the volume.
bypassing the INPUT selector, BASS, TREBLE, BALANCE
and LOUDNESS controls, SUBSONIC FILTER switch (AX-592
and AX-892 only), and the PRE OUT/MAIN IN terminals (AX- MUTING
592 and AX-892 only) and then goes directly to the amplifier.
This signal routing ensures the purest CD sound, eliminating
any alterations to the original CD signals. ON OFF

CD DIRECT AMP

Note
If both the CD DIRECT AMP and PURE DIRECT switches are
on, only the CD DIRECT AMP switch will function.

WARNING
When the LOUDNESS control has been set, if the PURE DIRECT switch or the CD DIRECT AMP switch is pressed, the sound
will suddenly increase and may damage your ears or the speaker (the LOUDNESS control function may be bypassed).
Therefore, only press the PURE DIRECT switch or the CD DIRECT AMP switch after lowering the volume or after checking
that the LOUDNESS control is properly set.

19
 TROUBLESHOOTING
If the unit fails to operate normally, check the following points to determine whether the fault can be corrected by the simple
measures suggested. If it cannot be corrected, or if the fault is not listed in the SYMPTOM column, disconnect the AC power plug
and contact your authorized YAMAHA dealer or service center for help.

SYMPTOM CAUSE REMEDY

The unit fails to turn on when the POWER The AC power plug is not plugged in or is not Firmly plug in the AC power plug.
switch is pressed, or turns off suddenly completely inserted.
soon after the power is turned on. The IMPEDANCE SELECTOR switch on the Set the switch to the upper or the lower end
rear panel is not set to the upper or the lower exactly.
end exactly.
No sound. Incorrect output cable connections. Connect the cables properly. If the problem
persists, the cables may be defective.
The appropriate input source is not selected. Select an appropriate input source with the
INPUT selector.
The SPEAKERS switches are not set Set the SPEAKERS switch, which corresponds
properly. to the speakers to be used, to ON.
Speaker connections are not secure. Secure the connections.
The jumpor pins (PRE OUT/MAIN IN) are not Connect the jumper pins properly.
connected properly. (AX-592 and AX-892 only) (AX-592 and AX-892 only)
Sound level is too low. The MUTING switch is pushed in. (Muting is Push the MUTING switch again. (Muting is off)
on) (AX-892 only) (AX-892 only)
The sound suddenly goes off. The protection circuit has been activated Turning the unit off and then on will reset the
because of a short circuit, etc. protection circuit.
Only one speaker outputs sound. Incorrect setting of the BALANCE control. Adjust it to the appropriate position.
Incorrect cable connections. Connect the cables properly. If the problem
persists, the cables may be defective.
There is a lack of bass and no ambience. The cable polarity is reversed at the amplifier Connect the speaker cables correctly.
or speakers.
The sound hums. Incorrect cable connections. Firmly connect the cables. If the problem
persists, the cables may be defective.
No connection from the turntable to the GND Make the GND connection between the
terminal. turntable and this unit.
Sound level is low or sound is distorted The LOUDNESS control is functioning. Set the LOUDNESS control to the FLAT
while playing a record on the turntable. position.
The PHONO (MM/MC) switch is set to the Set the PHONO (MM/MC) switch to the proper
improper position (AX-592 and AX-892 only). position (AX-592 and AX-892 only).
The volume level cannot be increased, or The power to the component connected to the Turn the power to the component on.
sound is distorted. REC OUT terminals of this unit is off.
Using the BASS, TREBLE, BALANCE, and The CD DIRECT AMP or PURE DIRECT The CD DIRECT AMP and PURE DIRECT
LOUDNESS controls and SUBSONIC switch is on. switches must be switched off to use those
FILTER switch (AX-592 and AX-892 only) controls.
does not affect the tone.
The input source can not be changed, The CD DIRECT AMP switch is on. Switch off the CD DIRECT AMP switch.
though the INPUT selector is turned.
The remote control does not work. Direct sunlight or lighting (of an inverter type of Change the position of the unit.
fluorescent lamp etc.) is striking the remote
control sensor of the unit.
The distance or range within which the The batteries of the remote control are too Replace the batteries with new ones.
remote control can be used decreases. weak.
The sound is degraded when listening with The power to this unit is off. Turn the power to this unit on.
the headphones connected to the compact
disc player or cassette deck that are
connected with this unit.

20
SPECIFICATIONS (AX-492)

English
AUDIO SECTION Output Level/Impedance Tone Control Characteristics
Minimum RMS Output Power per Channel REC OUT .......................150 mV/0.6 k-ohms BASS: Boost/cut ................10 dB (20 Hz)
8 ohms, 20 Hz to 20 kHz, 0.019% THD Turnover Frequency.........(350 Hz)
...................................................85W+85W Headphone Jack Rated Output/ Impedance TREBLE: Boost/cut...........10 dB (20 kHz)
6 ohms, 20 Hz to 20 kHz, 0.038% THD Output Level (8 ohms, 0.019% THD) Turnover Frequency.....(3.5 kHz)
...............................................100W+100W ...............................................................0.3V
Impedance.....................................680 ohms Continuous Loudness Control
Dynamic Power per Channel Attenuation ............................30 dB (1 kHz)
(by IHF Dynamic Headroom measuring Frequency Response (20 Hz to 20 kHz) (Level related equalization)
method) CD/TUNER/TAPE/AUX ....................00.5 dB
8/6/4/2 ohms ...................130/150/185/220W Gain Tracking Error (0 to 60 dB) ............2 dB
RIAA Equalization Deviation
DIN Standard Output Power per Channel PHONO...........................................00.3 dB
[Europe model only] GENERAL
(4 ohms, 1 kHz, 0.7% THD) ..............120W Total Harmonic Distortion (20 Hz to 20 kHz) Power Supply
PHONO to REC OUT (3V) ................0.003% [Europe and U.K. models] ...AC 230V, 50 Hz
IEC Power [Europe model only] CD/TUNER/TAPE/AUX to SP OUT [General model]
(8 ohms, 1 kHz, 0.019% THD) .............100W (42.5W/8 ohms) ................................0.008% ..................AC 110/120/220/240V, 60/50 Hz

Power Band Width Signal-to-Noise Ratio (IHF-A Network) Power Consumption ...............................210W
8 ohms, 42.5W, 0.038% THD PHONO (5 mV Input Shorted) ............ 88 dB
.............................................10 Hz to 50 kHz CD (CD DIRECT AMP ON, Shorted)... 110 dB AC Outlets
[Europe and General models]
Damping Factor SP-A Residual Noise (IHF-A Network) 3 SWITCHED OUTLETS ..100W max. total
8 ohms, 20 Hz20 kHz ..............240 or more CD (CD DIRECT AMP ON) ...................35 V [U.K. model]
PURE DIRECT ON ..............................90 V 1 SWITCHED OUTLET ....100W max. total
Maximum Output Power (EIAJ)
[General model only] Channel Separation Dimensions (W x H x D)
8 ohms, 1 kHz, 10% THD .................130W CD/TUNER/TAPE/AUX (Input 5.1 k-ohms ......................................435 x 151 x 391 mm
6 ohms, 1 kHz, 10% THD .................150W Terminated 1 kHz/10 kHz).........65 dB/50 dB (17-1/8 x 6.0 x 15-3/8)

Input Sensitivity/Impedance Weight .............................9.6 kg (21 lbs. 1 oz.)

PHONO ............................2.5 mV/47 k-ohms
CD/TUNER/TAPE/AUX ....150 mV/47 k-ohms Accessories ...........Remote control transmitter
Batteries
Maximum Input Signal (1 kHz, 0.003% THD)
PHONO.............................................115 mV
Specifications subject to change without
notice.

21
 SPECIFICATIONS (AX-592)
AUDIO SECTION Output Level/Impedance Tone Control Characteristics
Minimum RMS Output Power per Channel REC OUT .......................150 mV/0.6 k-ohms BASS: Boost/cut ................10 dB (20 Hz)
8 ohms, 20 Hz to 20 kHz, 0.015% THD PRE OUT ..............................1 V/1.2 k-ohms Turnover Frequency.........(350 Hz)
...............................................100W+100W TREBLE: Boost/cut...........10 dB (20 kHz)
6 ohms, 20 Hz to 20 kHz, 0.03% THD Headphone Jack Rated Output/ Impedance Turnover Frequency.....(3.5 kHz)
...............................................120W+120W Output Level (8 ohms, 0.015% THD)
.............................................................0.33V Filter Characterristics
Dynamic Power per Channel Impedance.....................................680 ohms SUBSONIC FILTER .........15 Hz, 18 dB/oct
(by IHF Dynamic Headroom measuring
method) Frequency Response (20 Hz to 20 kHz) Continuous Loudness Control
8/6/4/2 ohms ...................140/170/220/290W CD/TUNER/TAPE/AUX ....................00.5 dB Attenuation ............................30 dB (1 kHz)
MAIN IN...........................................00.5 dB (Level related equalization)
DIN Standard Output Power per Channel
[Europe model only] RIAA Equalization Deviation Gain Tracking Error (0 to 60 dB) ............2 dB
(4 ohms, 1 kHz, 0.7% THD) ..............155W PHONO MM....................................00.3 dB
PHONO MC ....................................00.5 dB
IEC Power [Europe model only] GENERAL
(8 ohms, 1 kHz, 0.015% THD) .............110W Total Harmonic Distortion (20 Hz to 20 kHz) Power Supply
PHONO MM to REC OUT (3V) .........0.003% [U.S.A. and Canada models]
Power Band Width PHONO MC to REC OUT (3V) .........0.007% ...........................................AC 120 V, 60 Hz
8 ohms, 50W, 0.03% THD CD/TUNER/TAPE/AUX to PRE OUT (1 V) [Australia model].................AC 240 V, 50 Hz
.............................................10 Hz to 50 kHz ..........................................................0.005% [Europe and U.K. models] ..AC 230 V, 50 Hz
CD/TUNER/TAPE/AUX to SP OUT [General model]
Damping Factor SP-A (50W/8 ohms) ...................................0.008% ..................AC 110/120/220/240V, 60/50 Hz
8 ohms, 20 Hz20 kHz ..............320 or more
Signal-to-Noise Ratio (IHF-A Network) Power Consumption ...............................220W
Maximum Output Power (EIAJ) PHONO MM (5 mV Input Shorted) ..... 92 dB [U.S.A model only] ...............................200W
[General model only] PHONO MC (500 V Input Shorted)... 76 dB
8 ohms, 1 kHz, 10% THD .................145W CD (CD DIRECT AMP ON Shorted) ... 110 dB AC Outlets
6 ohms, 1 kHz, 10% THD .................170W [U.S.A., Europe, Canada and General models]
Residual Noise (IHF-A Network) 3 SWITCHED OUTLETS ..100W max. total
Input Sensitivity/Impedance CD (CD DIRECT AMP ON) ...................35 V [Australia and U.K. models]
PHONO MM .....................2.5 mV/47 k-ohms PURE DIRECT ON ............................. 90 V 1 SWITCHED OUTLET ....100W max. total
PHONO MC ......................160 V/250 ohms
CD/TUNER/TAPE/AUX ....150 mV/47 k-ohms Channel Separation Dimensions (W x H x D)
MAIN IN .................................1 V/30 k-ohms CD/TUNER/TAPE/AUX (Input 5.1 k-ohms ......................................435 x 151 x 396 mm
Terminated 1 kHz/10 kHz).........65 dB/50 dB (17-1/8 x 6.0 x 15-1/2)
Maximum Input Signal (1 kHz, 0.007% THD)
PHONO MM......................................150 mV Weight ...........................10.6 kg (23 lbs. 4 oz.)
PHONO MC ........................................10 mV
Accessories ...........Remote control transmitter
Batteries

Specifications subject to change without

notice.

22
SPECIFICATIONS (AX-892)

English
AUDIO SECTION Output Level/Impedance Tone Control Characteristics
Minimum RMS Output Power per Channel REC OUT .......................150 mV/0.6 k-ohms BASS: Boost/cut ................10 dB (20 Hz)
8 ohms, 20 Hz to 20 kHz, 0.015% THD PRE OUT ..............................1 V/1.2 k-ohms Turnover Frequency.........(350 Hz)
...............................................115W+115W TREBLE: Boost/cut...........10 dB (20 kHz)
6 ohms, 20 Hz to 20 kHz, 0.03% THD Headphone Jack Rated Output/ Impedance Turnover Frequency.....(3.5 kHz)
...............................................140W+140W Output Level (8 ohms, 0.015% THD)
.............................................................0.35V Filter Characterristics
Dynamic Power per Channel Impedance.....................................680 ohms SUBSONIC FILTER .........15 Hz, 18 dB/oct
(by IHF Dynamic Headroom measuring
method) Frequency Response (20 Hz to 20 kHz) Continuous Loudness Control
8/6/4/2 ohms ...................150/200/250/330W CD/TUNER/TAPE/AUX ....................00.5 dB Attenuation ............................30 dB (1 kHz)
MAIN IN...........................................00.5 dB (Level related equalization)
DIN Standard Output Power per Channel
[Europe model only] RIAA Equalization Deviation AUDIO MUTING................................... 20dB
(4 ohms, 1 kHz, 0.7% THD) ..............190W PHONO MM....................................00.3 dB
PHONO MC ....................................00.5 dB Gain Tracking Error (0 to 60 dB) ............2 dB
IEC Power [Europe model only]
(8 ohms, 1 kHz, 0.015% THD) .............125W Total Harmonic Distortion (20 Hz to 20 kHz)
PHONO MM to REC OUT (3V) .........0.003% GENERAL
Power Band Width PHONO MC to REC OUT (3V) .........0.007% Power Supply
8 ohms, 57.5W, 0.03% THD CD/TUNER/TAPE/AUX to PRE OUT (1 V) [Europe model] ....................AC 230V, 50 Hz
.............................................10 Hz to 50 kHz ..........................................................0.005% [General model]
CD/TUNER/TAPE/AUX to SP OUT ..................AC 110/120/220/240V, 60/50 Hz
Damping Factor SP-A (57.5W/8 ohms) ................................0.008%
8 ohms, 20 Hz20 kHz ..............320 or more Power Consumption ...............................270W
Signal-to-Noise Ratio (IHF-A Network)
Maximum Output Power (EIAJ) PHONO MM (5 mV Input Shorted) ..... 92 dB AC Outlets
[General model only] PHONO MC (500 V Input Shorted)... 76 dB 3 SWITCHED OUTLETS ....100W max. total
8 ohms, 1 kHz, 10% THD .................160W CD (CD DIRECT AMP ON Shorted) ... 110 dB
6 ohms, 1 kHz, 10% THD .................190W Dimensions (W x H x D)
Residual Noise (IHF-A Network) ......................................435 x 171 x 396 mm
Input Sensitivity/Impedance CD (CD DIRECT AMP ON) .................. 35 V (17-1/8 x 6-3/4 x 15-1/2)
PHONO MM .....................2.5 mV/47 k-ohms PURE DIRECT ON ............................. 90 V
PHONO MC ......................160 V/250 ohms Weight ............................13 kg (28 lbs. 10 oz.)
CD/TUNER/TAPE/AUX ....150 mV/47 k-ohms Channel Separation
MAIN IN .................................1 V/30 k-ohms CD/TUNER/TAPE/AUX (Input 5.1 k-ohms Accessories ...........Remote control transmitter
Terminated 1 kHz/10 kHz).........65 dB/50 dB Batteries
Maximum Input Signal (1 kHz, 0.007% THD)
PHONO MM......................................150 mV
PHONO MC ........................................10 mV Specifications subject to change without
notice.

23
CARACTERISTIQUES TECHNIQUES (AX-892)
SECTION AUDIO Niveau de sortie/impdance Caratristiques de contrle de la tonalit
Puissance de sortie minimum RMS par canal REC OUT .......................150 mV/0,6 k-ohms BASS: Augmentation/coupure
8 ohms, 20 Hz 20 kHz, 0,015% de DHT PRE OUT ..............................1 V/1,2 k-ohms .............................10 dB (20 Hz)
.............................................115 W+115 W Frquence de renversement
6 ohms, 20 Hz 20 kHz, 0,03% de DHT Sortie nominale de prise de ..........................................350 Hz
.............................................140 W+140 W casque/impdance TREBLE: Augmentation/coupure
Niveau de sortie (8 ohms, 0,015% de DHT) ............................10 dB (20 kHz)
Puissance dynamique par canal ..........................................................0,35V Frquence de renversement
(Mesure par la mthode IHF Dynamic Impdance ..................................680 ohms ..........................................3,5 kHz
Headroom)
8/6/4/2 ohms ..................150/200/250/330 W Rponse en frquence (20 Hz 20 kHz) Filtre
CD/TUNER/TAPE/AUX ..................00,5 dB SUBSONIC FILTER .........15 Hz, 18 dB/oct
Puissance de sortie standard DIN par canal MAIN IN ..........................................00,5 dB
[Modle pour lEurope seulement] Contrle de contour continu
(4 ohms, 1 kHz, 0,7% de DHT) ........190 W Dviation dgalisation RIAA Attnuation ............................30 dB (1 kHz)
PHONO MM....................................00,3 dB (Egalisation relie au niveau)
Puissance IEC PHONO MC ...................................00,5 dB
[Modle pour lEurope seulement] AUDIO MUTING...................................20 dB
(8 ohms, 1 kHz, 0,015% de DHT) ....125 W Distorsion harmonique totale (20 Hz 20 kHz) Erreur du contrle de gain (0 60 dB) ...2 dB
PHONO MM REC OUT (3V) ..........0,003%
Largeur de bande de puissance PHONO MC REC OUT (3V) ..........0,007%
8 ohms, 57,5W, 0,03% de DHT CD/TUNER/TAPE/AUX PRE OUT (1V) CARACTERISTIQUES GENERALES
..............................................10 Hz 50 kHz ..........................................................0,005% Alimentation
CD/TUNER/TAPE/AUX SP OUT [Modle pour lEurope] ........CA 230V, 50 Hz
Facteur damortissement SP-A (57,5W/8 ohms) ................................0,008% [Modle gnral]
8 ohms, 20 Hz 20 kHz .............320 ou plus ..................CA 110/120/220/240V, 60/50 Hz
Rapport signal/bruit (IHF rseau A)
Puissance de sortie maximum (EIAJ) PHONO MM (5 mV entre court-circuite) Consommation ......................................270 W
[Modle gnral seulement] ............................................................ 92 dB
8 ohms, 1 kHz, 10% de DHT............160 W PHONO MC (500 V entre court- Prises CA
6 ohms, 1 kHz, 10% de DHT............190 W circuite) .......................................... 76 dB 3 PRISES COMMUTEES
CD (CD DIRECT AMP ON court-circuite) ....................................100 W max. au total
Sensibilit dentre/impdance .......................................................... 110 dB
PHONO MM .....................2,5 mV/47 k-ohms Dimensions (L x H x P)
PHONO MC .....................160 V/250 ohms Bruit rsiduel (IHF rseau A) ......................................435 x 171 x 396 mm
CD/TUNER/TAPE/AUX CD (CD DIRECT AMP ON) .................35 V
........................................150 mV/47 k-ohms PURE DIRECT ON ..............................90 V Poids .......................................................13 kg
MAIN IN ................................1 V/30 k-ohms
Sparation des canaux Accessoires .........Emetteur de tlcommande
Signal dentre maximum CD/TUNER/TAPE/AUX (entre termine 5,1 Piles
(1 kHz, 0,007% de DHT) k-ohms 1 kHz/10 kHz) ...............65 dB/50 dB
PHONO MM ...................................150 mV Caractristiques techniques modifiables sans
PHONO MC......................................10 mV pravis.

YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.
YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA
YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY
YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE
YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND
YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VSTRA FRLUNDA, SWEDEN
YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA VY64900-1
Printed in Malaysia