Step 1 Assemble Base Frame

Parts:
2020 Aluminium profile 375mm – 4pcs
Acrylic corner cushion – 4pcs
L-Shape connector (with grub screw) – 4pcs
M4-10mm screw – 12pcs
M4 T-Nut – 12pcs

 Connect each aluminium profiles using 4pcs L-

Shape connector, then tighten the grub screws.

 Mount the 4pcs acrylic corner cushion, secure

them with M4-10mm screw and T-Nut.
 Step 2 Placing Z-axis Slide Rail
Parts:
2020 Aluminium profile 440mm – 2pcs
Corner bracket – 4pcs
M5-25mm screws -2pcs
M4-8mm screws – 8pcs
M4 T-Nut – 8pcs

 Place 2pcs 440mm aluminium profiles on the

base , secure them with M5-25mm screws.

 Fix the Z-axis slide rails using 4pcs corner bracket,

secure them with M4-8mm and T-Nuts

 Ensure the correct distance.

(Front – 248mm , Back – 127mm )
 Step 3 Assemble Z Motor Bracket
Parts:
42 Motor bracket – 2pcs
M4-8mm – 4pcs
M4 T-Nut – 4pcs

 Attach the motor bracket to the bottom of Z slide

rail , both centre lines must be vertical. Then
secure them with M4-8mm screw and T-nuts.
 Step 4 Assemble Bed Frame
Parts:
2020 Aluminium profile 415mm – 1pcs
Bed frame – 1pcs
Wheel – 4pcs
Plastic pillar – 4pcs
M5-35mm- 4pcs
Locknut – 4pcs

 Secure the wheels in place using M5-35mm

screws and locknut ,using plastic pillar between
wheel and bed frame.

 Insert the aluminium profile between the wheels

and add this assembly to the base frame made
previously.
 Step 5 Placing Y-axis Slide Rail
Parts:
Corner bracket – 2pcs
M4-8mm screw – 4pcs
M4 T-Nut – 4pcs

 Place each end of the Y axis slide rail to the

middle of the base aluminium profiles. Connect
them with corner bracket , next secure it using
M4-8mm screw and T-nut .

The 2pcs corner bracket had been smoothed flat.

different than others.
 Step 6 Assemble Y-axis Belt Pulley
Parts:
Belt pulley – 1pcs
Y Pulley mount (acrylic) – 1pcs
M5-25mm screw – 1pcs
M5 Nut – 1pcs
M5 Locknut – 1pcs
M6 washer – 2pcs
M5 washer – 2pcs
M4-8mm screw – 2pcs
M4 T-Nut - 2pcs

 Take 1pcs M5-25mm screw and insert the Pulley

mount, secure it with M5 nut , then insert the
washers and belt pulley , secure them using M5
locknut.

 Secure the Y belt pulley assembly to the front of

the Y slide rail using 2pcs M4-8mm screws and
nuts.

 Tighten screws gently to avoid damaging the

acrylic.
 Step 7 Assemble Y axis Motor
Parts:
Limit switch – 1pcs
42 stepper motor – 1pcs
GT2-16 Pulley (with grub screw in it)– 1pcs
Y motor mount (Acrylic) – 1pcs
M3-6mm screw – 4pcs
M4-8mm screw – 2pcs
M4 T-Nut - 2pcs
M2-10mm screw – 2pcs
M2 Nut – 2pcs

 Secure the limit switch to motor mount using

2pcs M2-10mm screws and nuts. Then secure
the motor mount to the back of the Y slide rail
using 2pcs M4-8mm screws and T-nuts.

 Insert the GT2-16 pulley to the motor shaft,

tighten the grub screw in the pulley. Next Secure
the stepper motor to the motor mount using
4pcs M3-6mm screws.
 Step 8 Instal Y axis Timing Belt
Parts:
GT2 Timing belt – 1pcs
Zip-ties – 2pcs

 Tighten one end of the timing belt to the bed

frame using a zip-ties .

 Run the other end of timing belt along the

aluminium profile, through the Y-GT2-16 Pulley
and Belt pulley . Then tighten it to the bed frame
using zip-ties as shown in the picture .
 Step 9 Assemble Z Carriage_Left
Parts:
42 Motor bracket – 1pcs
Sliding plate (acrylic) – 2pcs
Brass nut – 1pcs
Brass nut holder_L – 1pcs
Plastic pillar – 6pcs
Wheel – 3pcs
M5-45mm screw – 3pcs M5 Nut – 3pcs
M4-12mm screw – 6pcs M4 Nut – 6pcs
M3-16mm screw – 2pcs M3 Nut – 2pcs

 Assemble the motor bracket and one sliding plate

using 4pcs M4-12mm screws and nuts.
 Put the brass nut into the holder_L using 2pcs
M3-16mm screws and nuts, then secure the
holder with one sliding plate using 2pcs M4-
12mm screws and nuts.
 Insert 3pcs M5-45mm screws to the sliding plate,
Put the wheels into M5-45mm screws, using
plastic pillars between wheel and acrylic, secure
them using M5 nuts.
 Please pay attention to the installing direction.
 Step 10 Assemble Z Carriage_Right
Parts:
42 Motor bracket – 1pcs
Sliding plate(acrylic) – 2pcs
Brass nut – 1pcs
Brass nut holder_R – 1pcs
Plastic pillar – 6pcs
Wheel – 3pcs
M5-45mm screw – 3pcs M5 Nut – 3pcs
M4-12mm screw – 6pcs M4 Nut – 6pcs
M3-16mm screw – 2pcs M3 Nut – 2pcs

 Put the brass nut into the holder_R using 2pcs

M3-16mm screws and nuts, then secure the
holder with one sliding plate using 2pcs M4-
12mm screws and nuts.
 Assemble the motor bracket and one sliding plate
using 4pcs M4-12mm screws and nuts.
 Insert 3pcs M5-45mm screws to the sliding plate,
Put the wheels into M5-45mm screws, using
plastic pillars between wheel and acrylic, secure
them using M5 nuts.
 Please pay attention to the installing direction.
 Step 11 Assemble the X axis
Parts:
2020 Aluminium profile 400mm – 1pcs
M4-12mm screws – 4pcs
M4 T-Nut – 4pcs

 Insert the two carriages into the Z slide rails.

 Take one 400mm Aluminium profile and attach to

the brass nut holders using M4-12mm screws
and T-nuts . Tighten screws gently to avoid
damaging the parts.
 Step 12 Place the X-motor
Parts:
42 Stepper motor – 1pcs
GT2-16 Pulley (with grub screw in it)– 1pcs
M3-6mm screw – 4pcs

 Tighten the X-motor to the motor bracket of the

left carriage , Using M3-6mm screws.

 Place GT2-16 Pulley on the motor shaft , tighten

up the pulley.
 Step 13 Install Filament Feeder
Parts:
42 Stepper motor – 1pcs
Feeding gear (with grub screw in it)– 1pcs
Extrution clip - 1pcs
Extrution seat – 1pcs
M3-22mm – 2pcs
M3-16mm – 1pcs
M5-10mm Hex screw – 1pcs
Spring – 1pcs

 Insert the feeding gear to the motor shaft and

them tighten up .

 Place the Extrution seat and motor to the bracket

as shown in the picture, secure them using 2pcs
M3-22mm screws.

 Put one M5-10mm hex screw and spring

between extrution clip and extrution seat , next
secure the extrution clip with motor using M3-
16mm screw.
 Step 14 Place the Z-Motors
Parts:
42 Stepper motor – 2pcs
Coupling (with grub screw in it) – 2pcs
M3-6mm screws – 8pcs

 Place the Z motors to the Z motor brackets ,

secure them using M3-6mm screws .

 Insert the couplings to the motor shaft. tighten

the grub screws in coupling.
 Step 15 Fix threaded rod
Parts:
M8 Threaded rod 380mm – 2pcs

 Take 2pcs M8 threaded rod through the brass

nuts ,then insert to the coupling and tighten up.
 Step 16 Cover the Top
Parts:
2020 Aluminium profile 440mm – 1pcs
M5-25mm – 2pcs

 Secure 440mm aluminium profile on the top

using M5-25mm screws .

 There a screw hole on the top of the Z slide rail

which had been tapped.
 Step 17 Insert Extruder Assembly
Parts:
Extruder assembly (with position sensor ) – 1pcs

 Carefully insert the extruder assembly to the X

slide rail.
 Step 18 Assemble X axis Belt Pulley
Parts:
Belt pulley – 1pcs
X Pulley mount (acrylic) – 1pcs
M5-25mm screw – 1pcs
M5 Nut – 1pcs
M5 Locknut – 1pcs
M6 washer – 2pcs
M5 washer – 2pcs
M4-8mm screw – 2pcs
M4 T-Nut - 2pcs

 Take 1pcs M5-25mm screw and insert the Pulley

mount, secure it with M5 nut , then insert the
washers and belt pulley , secure them using M5
locknut. (same as step 6)

 Secure the X belt pulley assembly on the right of

the X slide rail using 2pcs M4-8mm screws and
nuts.

 Tighten screws gently to avoid damaging the

acrylic.
 Step 19 Install X endstop
Parts:
Limit switch – 1pcs
X endstop mount (acrylic) – 1pcs
M4-8mm screw – 2pcs
M4 T-Nut – 2pcs
M2-10mm screw – 2pcs
M2 Nut – 2pcs

 Secure the limit switch to X endstop mount using

2pcs M2-10mm screws and nuts.

 Place the X endstop mount to the left end of the

X slide rail using 2pcs M4-8mm screw and T-nuts.
 Step 20 Install X axis Timing Belt
Parts:
GT2 Timing belt – 1pcs
Zip-ties – 2pcs

 Tighten one end of the timing belt to the belt

hole using a zip-ties which back of the extruder

 Run the other end of timing belt along the

aluminium profile, through the X-GT2-16 Pulley
and Belt pulley . Then tighten it to another belt
hole using a zip-ties, as shown in the picture .
 Step 21 Assemble Heat Bed Frame
Parts:
MK3 Heatbed – 1pcs
M3-30mm screw – 4pcs
Thumb nut – 4pcs
Spring – 4pcs

 Place the MK3 heatbed on the bed frame use

4pcs springs between them and then through
4pcs M3-30mm screws, then top 4pcs thumb
nuts under the bed frame.
 Step 22 Assemble Heat Bed Frame
Parts:
Teflon hose – 1pcs
Connector – 1pcs

 Instal a connector to the filament feeder , and

then insert a teflon hose between feeder and
extruder .
 Step 23-1 Assemble Electronic Box
Parts:
Electronic box bottom plate (acrylic) – 1pcs
Power supply – 1pcs
Mainboard – 1pcs
M3-10mm screws – 4pcs
M3-20mm screws – 4pcs
M3 nuts – 4pcs
Plastic pillar – 4pcs

 Place the power supply on the bottom plate

using M3-10mm screws.

 Place the mainboard on the bottom plate using

M3-20mm and nuts , insert the plactic pillar
between them.
 Step 23-2 Assemble Electronic Box
Parts:
Electronic box side plate (left) – 1pcs
Side plate (right) – 1pcs
Middle plate – 1pcs
Back plate – 1pcs
AC power switch
M3-10mm screw – 2pcs
M3-20mm screws – 6pcs
M3 nuts – 8pcs

 Insert the AC power switch to the back plate ,

secure them using 2pcs M3-10mm screws and
nuts

 Assemble the plates to the bottom plate as

picture , secure them using M3-20mm screws
and nuts.
 Step 23-3 Assemble Electronic Box
Parts:
Electronic box top plate (left) – 1pcs
LCD display assembly – 1pcs
M3-20mm screws – 7pcs
M3 nuts – 7pcs

 Cover the top plate using M3-20mm screws and

M3 nuts.

 Place the LCD display assembly to the box , using

2pcs M3-20mm screws and nuts.
 Step 24 Control Board Wiring Diagram
Parts:
Mainboard – 1pcs

 The method of connecting wire is as picture

 There is only 1pcs cooler fan , please connect

xx
to ‘CFAN’ on board

 For auto level 3D printer, there only 2pcs limit

switches , one for X-axis and one for Y-axis, the
Position sensor is for Z stop and auto leveling .
 Step 25 AC Power Connector Wiring Diagram
Parts:
Power supply – 1pcs
Power switch – 1pcs

 Connect Power cable as the picture (Right)

Note: There are different voltages in different country.

Please select the appropriate voltage by switch before power
on. As the picture below.
 Step 26 Assemble Filament Holder

 Separately put two Plastic Pipe holder on

two Filament support frame, locking with
Plastic Pipe four M3*20mm Round head screws & nuts.

 Connect the two Filament support frames

with two Fixed links , locking with four
M3*20mm Round head screws & nuts
Filament spool

Plastic Pipe
holder M3 nuts

Filament
support frame

M3*20mm Round
head screws

Fixed Link