Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                

Panasonic Refrigeraor NR-B472TZ - B412TZ v1.1

Download as pdf or txt
Download as pdf or txt
You are on page 1of 24

1.

1 Specifications
MODEL NR-B472TZ-S5
SPECIFICTIONS
Storage Capacity 448 L (PC : 338 L,FC : 110 L)
Gross Capacity 468 L (PC : 356 L,FC : 112 L)
Outside dimensions
Width 697 mm
Depth 754 mm
Height 1828 mm
Net weight 72 kg
Type Frost-free refrigerator
Temperature control Micro-computer control (FC:FCC sensor) / Full-automatic direct control (PC:Damper thermo.)

Defrosting Full-automatic control Start : micro-computer ; Finish : Defrost sensor


Defrost water disposal Full-automatic (Forcible evaporated into the air)
Exterior finish Polyester coated finish
Inner liner Vacuum formed ABS resin
Insulation Polyurethane foam (cabinet & door)
Power source 110 V / 60 Hz , 110 V / 50 Hz , 120 V / 60 Hz , 120 V / 50 Hz
SEALED UNIT
Compressor EFI100E13DGH
(Winding Resistance (U-W) 8.44 Ω
measured at 20℃ ) (U-V) 8.44 Ω
(V-W) 8.44 Ω
Evaporator Fin tube type
Condenser Wrapper type (Consealed condenser)
Refrigerant charge R600a , 60g
Oil charge 215ml
ELECTRIC PARTS
Overload protector MM3-71CCQ
FCC Sensor R-20 19.09 KΩ B:3850K
DEF. Sensor R13 3.4338 KΩ B:3850K
Fan motor 4515JL-09W-B36-GF6
Fuse E4A00072C , 250V / 10A / 72℃ or SF70E,250V / 10A / 73℃
Defrost heater 127V/180W/ 89.6 Ω
PC damper thermo. SD-0306
LED Lamp d.c 12V / 1.5 W
Door switch (PC) 125 V / 5 A , 250 V / 2.5 A
1.2 Specifications
MODEL NR-B412TZ-S5
SPECIFICTIONS
Storage Capacity 388 L (PC : 278 L,FC : 110 L)
Gross Capacity 408 L (PC : 296 L,FC : 112 L)
Outside dimensions
Width 697 mm
Depth 754 mm
Height 1646 mm
Net weight 65 kg
Type Frost-free refrigerator
Temperature control Micro-computer control (FC:FCC sensor) / Full-automatic direct control (PC:Damper thermo.)

Defrosting Full-automatic control Start : micro-computer ; Finish : Defrost sensor


Defrost water disposal Full-automatic (Forcible evaporated into the air)
Exterior finish Polyester coated finish
Inner liner Vacuum formed ABS resin
Insulation Polyurethane foam (cabinet & door)
Power source 110 V / 60 Hz , 110 V / 50 Hz , 120 V / 60 Hz , 120 V / 50 Hz
SEALED UNIT
Compressor EFI100E13DGH
(Winding Resistance (U-W) 8.44 Ω
measured at 20℃ ) (U-V) 8.44 Ω
(V-W) 8.44 Ω
Evaporator Fin tube type
Condenser Wrapper type (Consealed condenser)
Refrigerant charge R600a , 60g
Oil charge 215ml
ELECTRIC PARTS
Overload protector MM3-71CCQ
FCC Sensor R-20 19.09 KΩ B:3850K
DEF. Sensor R13 3.4338 KΩ B:3850K
Fan motor 4515JL-09W-B36-GF6
Fuse E4A00072C , 250V / 10A / 72℃ or SF70E,250V / 10A / 73℃
Defrost heater 127V/180W/ 89.6 Ω
PC damper thermo. SD-0306
Lamp bulb d.c 12V / 1.5 W
Door switch (PC) 125 V / 5 A , 250 V / 2.5 A
1.3 TEMPERATURE CHARACTERISTIC
TEMPERATURE OF EACH COMPARTMENT,COMPRESSOR RUNNING RATIO
Temperature FREEZER COMPARTMENT MIN MED MAX
Adjuetment REFRIGERATOR COMPARTMENT 1 MED 7
Freezer compartment (FC) Temp.(degree) -16.0 -18.0 -20.0
Refrigerator compartment (PC) Temp.(degree) 5.0 4.0 0.0
Fine Freesh room (FF) Temp.(degree) 3.5 1.0 -1.0
Compressor running ratio (%) 63.0% 65.0% 68.0%

(CONDITION)
Atmosphere Temperature:32 degree
NO LOAD (NO FOODS), NO DOOR OPEN AND CLOSE
These indicating temperature is stable condition. (Approximately)
2.Introduction
FUNCTION OF ELECTRONIC CONTROL

2.1 FREEZER TEMPERATURE CONTROL


It actuates the compressor, FC fan motor ,and cooling system switch according to temperature variation
in the freezer compartment. And atmosphere temperature by processing the input from, FC temperature
sensor and adjustment of temperature control.

2.2 COMPRESSOR ROTATION SPEED CONTROL


According to changing inside temperature,the motor runs in the difference speed. In normal, the motor run in the
low speed. (Energy saving & lower noise.)
When powerful cooling is required, motor run in rapid speed.

CONDITION NR-B472TZ ROTATION SPEED(rps)


When to plug in 42
Quick freezing 42、71
Normal operation 32、 36、42、52、 58、 71

2.3 QUICK FREEZING FUNCTION


Press "QUICK FREEZING"button , and then quick function starts and LED sign comes on.
It actuates the compressor continuously for certain period regardless of compartment temperature, by processing
the input from AT temperature sensor. (AT temperature : Atmosphere temperature)

ATC NR-B472TZ continuous run


under than 18℃ 60 minutes/42rps
More than 19℃ 150 minutes/71rps

※When the blue light is blinking after pressing the "QUICK FREEZING" button, the function of quick freezing
is waiting .The situation of refrigerator is processing as below:
a.The refrigerator is defrosting .
b.The compressor is stopped,because temperature of the freezing compartment reachs setting of temperature.
When the above situation is solved , quick- freeze will be started automatically,then the "QUICK FREEZING"
light bright is on.

2.4 FC DEFROSTING CONTROL

Cumulating the compressor running time of certain period or time after defrosting according to AT temperature,
FC defrosting cycle starts. (AT temperature : Atmosphere temperature)
Termination is detected by defrost sensor ,but maximum defrosting time is 60 minutes (Defrosting forcibly stops).

Accumulating time for defrosting


Compressor protection(IPD) 15 hours
initially starts 4 hours
Power Interruption Continue cycle

ATC After defrosting Accumulation of compressor run time


under than 22℃ 13 hours ―
More than 33℃ ― 8 hours
2.5 WAITING CONTROL FOR COMPRESSOR RE-STARTING
To re-start the compressor smoothly after compressor stops and after defrosting, it does not actuate the compressor
for certain period.

Waiting time for compressor starting


10 minutes After compressor stops
3 minutes After defrosting
Caution
At once unplug, wait for 10 minutes, then plug in.

2.6 FAN MOTOR CONTROL IN FREEZER COMPARTMENT


The fan motor (near FC evaporator )is controlled under below condition.
compartment is closed.Rotation speed changes on 3 degree according to atmosphere temperature and refrigerator
compartment.

2.7 PROTECTION OF INVERTER CIRCUIT


When supply voltage drops, IPM protection operates, and compressor protection operates continuously,
compressor stops at the moment and indicates code"H41".

CODE Operation PCB Display


"MAX"LED: light off
H41 "MED"LED: light on
"MIN"LED: light on
"QUICK FREEZING" LED: light off

2.8 DOOR ALARM


When the door of refrigerator compartment is opened after 5 minute ,"QUICK FREEZING"light is red.
"QUICK FREEZING"light is off,when the door of refrigerator compartment is closed.

DOOR OPENING Buzzer sounds


after 1 minute Pee,Pee
after 3 minutes Pee,Pee,Pee,Pee
after 5 minutes Pee,Pee,Pee,…….

2.9 SELF DIAGNOSIS FUNCTION


If the unit have any problem ,the sign is appeared on LED.
(When "QUICK FREEZING" LED indicate red bright. Press "QUICK
FREEZING" + "FREEZER CONTROL" both bottons 9~13 sec plus than going
into SELF DIAGNOSIS FUNCTION.)

(Example:Code"H07")

CODE Operation PCB Display


"MAX"LED: light off
"MED"LED: light on
H07
"MIN"LED: light off
"QUICK FREEZING" LED: light off

2.10 AUTO ROOM LED LIGHTS OFF


If PC door opens for 1 hour, room led lights automatically comes off.
Once closing PC door, this function is reset.
3. Operation Instructions
SELF DIAGNOSIS FUNCTION
*When "QUICK FREEZING" LED indicate red bright.
Press "QUICK FREEZING" + "FREEZER CONTROL" both bottons 9~13 sec plus than going into SELF DIAGNOSIS FUNCTION.

No CODE Operation PCB Display Content Symptom Confirm point Solve

"MAX"LED: light off 1.The door of refrigerator 1.Close the refrigerator compartment
"MED"LED: light off compartment is opened. door
"MIN"LED: light off Refrigerator have not 2.Door switch is breakdown. 2.Replace door switch
1 U10 Door opened alarm.
"QUICK FREEZING" LED cooling 3.Control PCB is breakdown. 3.Replace Control PCB
: light on

"MAX"LED: light off Freezer compartment Compressor is stopped. 1.Check freezer compartment of 1.Replace freezer compartment of
"MED"LED: light off of sensor was open Refrigerator have not sensor. sensor.
"MIN"LED: light on circuit. cooling at all. 2.Check Control PCB of 2.Replace Control PCB.

"QUICK FREEZING" LED Freezer compartment Compressor is running connector. 3.Replace Control PCB.

: light off of sensor was short all the time. 3.Control PCB is breakdown.
2 H01
circuit. Refrigerator is over cooling
at all.
Freezer compartment Refrigerator have not
of sensor put error of cooling at all,or over
position cooling at all.
"MAX"LED: light off Defrost of sensor Thermal fuse was cut off 1.Check defrost of sensor. 1.Replace defrost of sensor.
"MED"LED: light off was open circuit. in freezer compartment 2.Check Control PCB of 2.Replace Control PCB.
"MIN"LED: light on Defrost of sensor The refrigerator have not connector. 3.Replace Control PCB.
3 H05 "QUICK FREEZING" LED was short circuit. defrosting . 3.Control PCB is breakdown.
: light on Defrost of sensor Evaporator have over frost
put error of position Refrigerator have not
cooling at all.
"MAX"LED: light off ATC of sensor Refrigerator is over cooling 1.Check ATC of sensor. 1.Replace defrost of sensor.

"MED"LED: light on was open circuit*. at all. 2.Check Control PCB of 2.Replace Control PCB.

"MIN"LED: light off connector. 3.Replace Control PCB.


4 H07 "QUICK FREEZING" LED Refrigerator have not 3.Control PCB is breakdown.
ATC of sensor
: light off was short circuit*. cooling at all.

"MAX"LED: light on Freezer compartment Refrigerator have not 1.Check defroster of heater. 1.Replace defroster of heater
"MED"LED: light on defrost abnormal defrosting. 2.Check Control PCB of 2.Replace Control PCB.
"MIN"LED: light on connector. 3.Replace Control PCB.
5 H31 "QUICK FREEZING" LED 3.Control PCB is breakdown.
: light on 4.Thermal fuse was cut off
in freezer compartment.

*ATC sensor is to measure atmosphere temperature . ATC sensor put on operation board.
No CODE Operation PCB Display Content Symptom Confirm point Solve

"MAX"LED: light off Protection of IPM for 1. "QUICK FREEZING" LED 1.Control PCB is breakdown. 1.Replace Control PCB.
"MED"LED: light on compressor lock indicate red bright.
"MIN"LED: light on
8 H40 "QUICK FREEZING" LED
: light off

"MAX"LED: light on Control PCB of 1. "QUICK FREEZING" LED 1.Control PCB is breakdown. 1.Replace Control PCB.
"MED"LED: light on communication is indicate red bright.
"MIN"LED: light on abnormal.
9 H50 "QUICK FREEZING" LED
: light off

"MAX"LED: light on Control PCB is 1. "QUICK FREEZING" LED 1.Control PCB is breakdown. 1.Replace Control PCB.
"MED"LED: light off abnormal. indicate red bright. 2.Check DFC of sensor. 2.Replace DFC of sensor
"MIN"LED: light on (DFC of sensor less 2. Refrigerator have not
10 H35 "QUICK FREEZING" LED then -41℃) cooling.
: light off

"MAX"LED: light on Control PCB is 1. "QUICK FREEZING" LED 1.Control PCB is breakdown. 1.Replace Control PCB.
"MED"LED: light off abnormal. indicate red bright. 2.Check DFC of sensor. 2.Replace DFC of sensor
"MIN"LED: light on (DFC of sensor more 2. Refrigerator have over
11 H36 "QUICK FREEZING" LED then 41℃) cooling.
: light on

"MAX"LED: light on Ambient brightness 1.Check Ambient brightness 1.Replace Control PCB.

"MED"LED: light on sensor was open circuit. 2.Check Control PCB of

"MIN"LED: light off connector.


12 H64 "QUICK FREEZING" LED
Ambient brightness
: light on sensor was short circuit.
4.Troubleshooting Guide
4.1 Symptom 1. Refrigerator have not cooling at all.

Compressor does not run

‧Press "QUICK FREEZING" botton 1~2 sec ,then release

NO YES
Check compressor is running or Check compressor side of *Reconnect compressor
not. connector dropped side of connector.
or not.

NO

YES
Check control PCB of *Reconnect control PCB
compressor of connector of compressor of
dropped or not. connector.

NO

‧Press "QUICK FREEZING" + "FREEZER CONTROL" both bottons 9~13 sec

"MAX"LED: light on
"MED"LED: light on *Replace control PCB.
"MIN"LED: light on YES
(Circuit problem happens between IC1
"QUICK FREEZING"LED: light off and IC 201).
CODE(H50)

NO

"MAX"LED: light off *Replace Control PCB .


"MED"LED: light on YES (Faulty at compressor control circuit)
"MIN"LED: light on or *Replace compressor.
"QUICK FREEZING"LED: light off (Compressor Lock)
CODE(H40)
4.2 Symptom 2. poor cooling.

Does "QUICK FREEZING" LED NO YES


Is door open? *Close door
indicate red bright?

‧Press "QUICK FREEZING" + "FREEZER CONTROL"
*Replace door switch.
YES both bottons 9~13 sec (Faulty at door switch,
NO
freezer of compartment fan
motor stop running)
"MAX"LED: light off
"MED"LED: light off
"MIN"LED: light on YES
"QUICK FREEZING"LED: light off *Replace freezer of
CODE(H01) compartment sensor
(sensor open circuit).

NO

*Replace Defrost heater


(heater open circuit).
"MAX"LED: light off
or *Replace Control PCB.
"MED"LED: light off YES NO (Faulty of relay on control
Is temperature fuse
"MIN"LED: light on PCB)
breakdown?
"QUICK FREEZING"LED: light on
CODE(H05)

YES *Replace Defrost sensor


(sensor open circuit).
NO
and *Replace temperature
fuse(fuse open circuit).

"MAX"LED: light on
"MED"LED: light on *Replace Defrost heater
"MIN"LED: light on YES NO
Is temperature fuse (heater open circuit).
"QUICK FREEZING"LED: light on breakdown? or *Replace Control PCB.
CODE(H31) (Faulty of relay on control
PCB)

NO
*Replace Defrost sensor
YES (sensor open circuit).
and *Replace temperature
fuse(fuse open circuit).

NEXT PAGE
4.3 Symptom 2. FC/PC are poor cooling.

YES *Re-put Defrost of sensor position.


Does evaporator get too much frost? ( Defrost of sensor drop)

NO

NO *Replace defrost sensor


(sensor of resistance is smaller)

Is resistance of defrost sensor


6.33-6.437kΩ(at 0 ℃)

YES
*Replace control PCB.
(Faulty of defrost sensor of circuit
detected on control PCB)
5. Disassembly and Assmbly Instructions ICE TRAY RAIL

5.1 ICE TRAY RAIL


ICE TRAY AS
‧Take out the CRYSTAL SHELF FC
‧Take out the ICE BOX
ICE BOX
‧Take out the ICE TRAY AS. ICE TRAY RAIL
‧Remove the screw ( 2 pcs)
‧Remove the ICE TRAY RAIL

5.2 COVER COIL CONNECTOR BAG


‧Remove the COVER

like right figure show

‧Remove the screw ( 2 pcs)


‧Remove the COVER CONNECTOR FC
‧Remove the screw ( 1 pcs)
‧Disconnect all the connector of harness
‧Remove the COVER COIL
Lead wire
COVER COIL
COVER CONNECTOR FC
COVER

5.3 DC FAN MOTOR


HOOK HOOK
‧Remove the COVER COIL

‧Remove the DC FAN MOTOR

To replace the DC fan motor


‧Insert the DC fan motor case into the
COVER COIL BACK
‧Connect the terminal. HOOK

5.4 FCC SENSOR


‧Remove the screw ( 1 pcs ) and remove the Al tape To replace the FCC SENSOR
‧Disassembly the hook around side ‧FCC SENSOR should be hooked in plate.

‧Disassembly the COVER COIL FRONT and COVER COIL BACK

‧Remove the FCC SENSOR


COVER COIL FRONT
COVER COIL BACK

‧Remove the Al tape


5.5 DEFROST HEATER CONNECTOR CONNECTOR

‧Remove the cover coil as.


‧Remove the lead wire . DFC SENSOR
‧Disconnect both side connector of heater lead wire . FIN EVAPARATOR
‧Lifting the evaporator at right gradually, pull it toward you.
‧Remove the DEFROST HEATER.
Lead wire
NOTE :
Special care should be taken not to twist and break the pipe.

TEMP FUSE
DEFROST HEATER

Lead wire

HooK
HooK

5.6 TEMP FUSE & DFC SENSOR


‧Remove the Lead wire
‧Disconnect the connector of TEMP FUSE.
‧Remove the TEMP FUSE.

DFC SENSOR

Lead wire

To replace the DFC SENSOR


‧DFC SENSOR should be hooked in plate.
TEMP FUSE
5.7 LED COVER & LED LAMP PCB 5.8 CONTROL PANEL PC
BUTTON CONTROL ‧Remove the LED pcb connector
PANEL.

DIAL THERMO PC

Screw

Control panel

LED Lamp cover

‧Remove the screw(4pcs).

‧Use a slotted screwdriver to unhook the LED lamp cover

gently knock

Don't dig into the led's


lamp cover ‧Take the control panel AS.

‧ LED lamp cober Assembly


5.9 DAMPER THERMOSTAT
‧Remove Control panel and pull out the ‧Remove the thermostat dial.

PULL

PULL ‧Tear off the tapes on insulation.


Open the insulation from the front side pull the upper portion.
‧Remove the damper thermostat from insulation.

Ins. Control panel back

‧Disconnect the terminal.

‧Disconnect the ins. control panel AS. & control panel.

Control panel

Damper thermo. Ins. Control panel front

To replace damper thermo.


‧Sealing dial should be put in place.
Ins.control panel AS.
‧Seal the gap between the front insulation and the back insulation
by putting tape.

‧Hook the sensor bulb in place.


5.10 STARTING RELAY & OVERLOAD PROTECTOR
‧Pull the potector cover leftwards to remove. ‧Pull the starting relay leftwards to remove.

Pulling
Starting relay

Protector cover Starting relay

‧Pull out the overload protector. To replace starting relay


‧Insert the starting relay into comp. pin.
‧Install the overload protector into protector cover.
Protector cover ‧Pushing the protector cover into comp.
Overload protector

Pushing

REFRIGERANT FLOW DIAGRAM


‧Refrigerant flows in the refrigerating units as shown in the figure.
‧Number in the figure of " PIPE LAYOUT " corresponds to number in the refrigerant flow diagram.

Suction pipe(Evaporator) Pipe pan water eva.

Mullion Side

Mullion Side Mullion Bottom

COMP
Mullion Front

Mullion Front

Dryer
5.11 Refrigeration system diagram

MULLION DRYER FRONT


B412TZ:¢4 x t0.38—1/2H L=6038
B472TZ:¢4 x t0.38—1/2H L=6504

MULLION DRYER SIDE


B412TZ:¢4 x t0.38—1/2H L=11561
B472TZ:¢4 x t0.38—1/2H L=11071

Screw

Evaporator

PIPE PAN WATER AS.


¢4 x t0.4 L=1510

SUCTION JOINT PIPE


¢6.35 x t0.5 L=435

MULLION DRYER BOTTOM


¢4 x t0.4 L=1939

CAPILLARY TUBE
COMP
DRYER JOINT PIPE
GAS CHARE PIPE ¢4 x t0.38 x 1/2H L=170
¢6.35 x t0.6 L=120

GAS CHAR DRYER PIPE


PAN WATER EVA JOINT PIPE Dryer ¢4 x t0.6 L=100
¢4.76 x t0.4 L=433
6. Installation Dimensions
100mm 697mm 100mm

300mm
1646mm(NR-B412TZ)
1828mm(NR-B472TZ)

716mm

(500mm)

754mm 40mm
7. Wiring Connection Diagram
8. Schematic Diagram
9. Location and Replacement Parts List
9.1.1 Location of Parts

NR-B412TZ
9.1.2 Location of Parts

NR-B472TZ
9.1.3 Replacement Parts List
Ref.No Service Parts No. Parts Name & Description B412TZ-S5 B472TZ-S5 PCS/SET NOTE

CNRBC-33918S SHELL N LINER AS.(FOAM) ○ ─ 1


100
CNRBC-33921S SHELL N LINER AS.(FOAM) ─ ○ 1
101 CNRAD-33380DH COVER HINGE TOP ○ ○ 1
102 CNR38-193801T FLANGE N HEXAGON 5 TS 14 ○ ○ 3
103 CNRAE-11710T HINGE TOP R ○ ○ 1
104 CNRBH-14171B CRYSTAL SHELF FC AS. ○ ○ 1
105 CNRAE-11663T HINGE CENTER ○ ○ 1
106 CNR38-193801T FLANGE N HEXAGON 5 TS 14 ○ ○ 2
107 CNRAG-16606T DOOR SW. ○ ○ 1
108 CNRAH-13282W MEAT TRAY STOPPER ○ ○ 2
109 CNRXTT4+12AV TRUSS 4 TS 12AV ○ ○ 2
110 CNRAH-28654B MEAT TRAY ○ ○ 1
111 CNRAH-28653B MEAT TRAY DOOR ○ ○ 1
3 B412TZ
112 CNRAH-28697T GLASS SHELF PC ○ ○
4 B472TZ
113 CNRAH-28655B CRISPER ○ ○ 1
114 CNRBC-33895Z CASTER AS R. ○ ○ 1
115 CNRBC-16959Z CASTER AS. L ○ ○ 1
116 CNRAC-18337T ADJUSTER BOLT R ○ ○ 1
117 CNRAC-24022T ADJUSTER BOLT ○ ○ 1
118 CNR38-193801T FLANGE N HEXAGON 5 TS 14 ○ ○ 4
119 CNRAD-34582T FC DOOR GASKET ○ ○ 1
120 CNRBD-35229S DOOR AS. FC (FOAM) ○ ○ 1
121 CNRAD-33980T EMBLEM MARK PLATE ○ ○ 1
122 CNRBD-35233B OPERATION PANEL AS ○ ○ 1
123 CNRXTT4+12AV TRUSS 4 TS 12AV ○ ○ 1
124 CNRAH-28644B SUP. SHELF FC ○ ○ 2
125 CNRAD-13785B TRAY EGG 10 ○ ○ 2
126 CNRAH-28645B EGG SHELF ○ ○ 2
1 B412TZ
127 CNRAH-28646B FREE RACK ○ ○
2 B472TZ
128 CNRAD-34628T SLIDE STOPPER PC ○ ○ 1
129 CNRAH-28647B BOTTLE SHELF PC ○ ○ 1
CNRAD-34602T PC DOOR GASKET ○ ─ 1
130
CNRAD-34598T PC DOOR GASKET ─ ○ 1
CNRBD-35231S DOOR AS. PC(FOAM) ○ ─ 1
131
CNRBD-35227S DOOR AS. PC(FOAM) ─ ○ 1
132 CNRAD-34681B OPERATION SHEET ○ ○ 1
133 CNRAK-15304T OPERATION MANUAL ○ ○ 1
134 CNRAK-15222T CORNER ROCK TOP R ○ ○ 1
135 CNRAK-15223T CORNER ROCK TOP L ○ ○ 1
CNRAK-15307S PACKING CASE ○ ─ 1
136
CNRAK-15306S PACKING CASE ─ ○ 1
137 CNRAK-153320 POLYLON BOTTOM BASE ○ ○ 1
9.2.1 Location of Parts
9.2.2 Replacement Parts List
Ref.No Service Parts No. Parts Name & Description B412TZ-S5 B472TZ-S5 PCS/SET NOTE

201 CNRAH-13309W ICE TRAY RAIL ○ ○ 1


202 CNRXTT4+12AV TRUSS 4 TS 12AV ○ ○ 2
203 CNRBH-10241W ICE TRAY AS. ○ ○ 1
204 CNRAH-13308B ICE BOX ○ ○ 1
205 CNRAC-22768T EVA HOLDER R. ○ ○ 1
206 CNRAC-22769T EVA HOLDER L. ○ ○ 1
207 CNRXTT4+12AFJ TRUSS 4 TS 12 ○ ○ 2
208 CNRAF-17324T FIN EVAPARATOR ○ ○ 1
209 CNRBG-19005T TEMP. FUSE AS. ○ ○ 1
210 CNRAG-17160T COVER RADIANT HEATER ○ ○ 1
211 CNRAG-17272T DEFROST HEATER ○ ○ 1
212 CNRXTN4+10AFJ TRUSS 4 TS 10 ○ ○ 1
213 CNRAC-22736T COVER COIL BACK ○ ○ 1
214 CNRAG-17174T FC FAN MOTOR 6P ○ ○ 1
215 CNRAJ-14076T FAN MOTOR PU FOAM ○ ○ 1
216 CNRBG-19158T FCC SENSOR AS ○ ○ 1
217 CNRAC-22737T COVER COIL FRONT ○ ○ 1
218 CNRXTT4+16A TRUSS 4 TS 16 ○ ○ 2
219 CNRAC-22754T COVER CONNECTOR FC ○ ○ 1
220 CNRXTT4+12AFJ TRUSS 4 TS 12 ○ ○ 1
221 CNRAJ-14088T SEAL PU FOAM ○ ○ 1
CNRAC-22751T INS. CONTROL PANEL B ○ ─ 1
222
CNRAC-22739T INS. CONTROL PANEL B ─ ○ 1
223 CNRAG-17190T BAFFLE THER ○ ○ 1
224 CNRAC-22738T INS. CONTROL PANEL F ○ ○ 1
225 CNRAH-28763T DIAL THERMO PC ○ ○ 1
226 CNRAH-24552T AG BIO FILTER ○ ○ 1
CNRAH-28663T CONTROL PANEL ○ ─ 1
227
CNRAH-28640T CONTROL PANEL ─ ○ 1
228 CNRXTT4+12AFJ TRUSS 4 TS 12 ○ ○ 4
229 CNRAH-13267W BUTTON CONTROL PANEL ○ ○ 2
CNRBG-18819T LED LAMP PCB AS. ○ ─ 1
230
CNRBG-15194T LED LAMP PCB AS. ─ ○ 1
CNRAH-28665T LED LAMP COVER ○ ─ 1
231
CNRAH-28642T LED LAMP COVER ─ ○ 1
232 CNRXSB4D8BNS BIND 4 SCREW 8 ○ ○ 2
233 CNRBG-19022T MICON PCB AS ○ ○ 1
234 CNRBG-18048T NOISE FILTER AS. ○ ○ 1
235 CNRBG-19184T AC CORD AS. ○ ○ 1
236 CNRXTT4+12AV TRUSS 4 TS 12AV ○ ○ 1
237 CNRBE-10924T COVER PLATE PCB BASE AS. ○ ○ 1
238 CNRC4585-480AJ SPECIAL SCREW ○ ○ 2
240 CNRAK-15175T CAUTION LABEL ○ ○ 1
241 CNRAF-14103T 2 WAY DRYER 5g ○ ○ 1
242 CNRBF-13811T PAN WATER EVA AS. ○ ○ 1
243 CNRAJ-10222T FLANGE N TRUSS 4 TS 13 ○ ○ 2
244 CNR39-03011T U-RING 7 ○ ○ 2
245 CNR06-59529R OVERLOAD PROTECTOR ○ ○ 1
246 CNRGD-12208T PROTECTOR COVER ○ ○ 1
247 CNRBF-11363T PIPE PAN WATER EVA.AS. ○ ○ 1
CNR91-23682T COMP (exclude oil)
248 ○ ○ 1
CNR91-23682A COMP (include oil)
249 CNR39-941120T RUBBER GROMMET ○ ○ 4
250 CNRBF-15607T COMP. BASE N ROLLER AS. ○ ○ 1
251 CNR08-21784A FLANGE N HEXAGON 5 TS 18 ○ ○ 4
252 CNRAG-16608T DFC SENSOR ○ ○ 1

You might also like