Rs68n Series
Rs68n Series
Rs68n Series
REFRIGERATOR CONTENTS
1. PRECAUTIONS(SAFETY WARNINGS)·················· 5
2. PRODUCT SPECIFICATIONS································ 8
4. TROUBLESHOOTING········································· 51
5. PCB DIAGRAM···················································· 87
6. WIRING DIAGRAM············································· 91
All rights reserved. This service guide may not be reproduced in whole or as a
part in any form whatsoever without the written permission of the SAMSUNG
ELECTRONICS Company.
Contents
1. PRECAUTIONS (SAFETY WARNINGS)...........................................................................................5
2. PRODUCT SPECIFICATIONS......................................................................................................... 8
2-1. Introduction of Main Function............................................................................................................. 8
2-2. Model Specification............................................................................................................................... 9
2-3. Basic Specification...............................................................................................................................14
2-4. Dimensions (mm/inch)........................................................................................................................ 17
2-5. Optional Material Specification.........................................................................................................19
4. TROUBLESHOOTING...................................................................................................................51
4-1. Using the control panel.......................................................................................................................51
4-2. SmartThings (available only with the optional dongle)............................................................... 56
4-3. Adjust the leveling feet and door height......................................................................................... 58
4-4. Function for failure diagnosis........................................................................................................... 65
4-5. Diagnostic method according to the trouble symptom(Flow Chart).........................................80
5. PCB DIAGRAM............................................................................................................................. 92
5-1. PBA Layout with part position........................................................................................................... 92
5-2. PBA Layout with part position (LC3_3050 Inverter PBA)............................................................. 93
5-3. Connector Layout with part position (Main Board)....................................................................... 94
5-4. Connector Lay out with part position (LC3_3050 Inverter PBA)................................................. 95
Contents
6. WIRING DIAGRAM...................................................................................................................... 96
6-1. Model : 2 Door, In-Door Ice Maker (RS68N82*, RS68N83*, RS6GN82*, RS6GN83*)............... 96
6-2. Model : 2 Door, In-Cabi Ice Maker (RS67N82*, RS67N83*)........................................................... 97
6-3. Model : 2 Door, Basic (RS66N81*)..................................................................................................... 98
7. BLOCK DIAGRAM........................................................................................................................ 99
7-1. DISPENSER + INDOOR I/M + PLUMBING.......................................................................................... 99
7-2. DISPENSER + INDOOR I/M + NON-PLUMBING............................................................................. 100
7-3. DISPENSER + INCABI I/M + PLUMBING...........................................................................................101
7-4. NO DISPENSER................................................................................................................................... 102
7-5. Inverter Block Diagram..................................................................................................................... 103
● Unplug the appliance before the changing or repairing the electric parts.
● Use rated electronic Control equipment.
➝ Make sure to check out ModeL name, Rated voltage, Rated current,
Operation Temp, etc.
● Upon repair, make sure that harnesses are not to be water-penetrated and
are bundled tight.
➝ Should not be detached by a certain amount of external force.
● Upon repair, completely remove dust or other foreign substances from
housing, harness, connector, etc.
➝ To prevent fire by tracking, short, etc.
● Check out whether water has penetrated into the electronic Control system.
➝ If there is any kind of trace, take necessary measures such as related
component change, insulation tapping, etc.
● After repair, check out the assembled state of parts.
➝ It should be the same as the previous state.
● Check out the surrounding conditions.
➝ Change the location, if the fridge is located at humid, wet places or the
installed state is unstable.
● In order to reduce the risk of electric shock the appliance must be properly
grounded.
● Do not allow consumers to overload a certain outlet.
● Check out whether the power cord or the outlet is broken, squeezed,
chopped off or heatdeformed.
➝ Repair or replace the defective power cord/outlet immediately.
➝ Make sure the power cord is not punctuated or stomped down.
● Do not allow consumers to keep food frayed or place bottles in the Freezer Room.
● Do not allow consumers to repair the fridge by themselves.
● Do not allow consumers to keep things except for food.
➝ Pharmaceutical, Chemical substances : These are not possible to be fine-
Controlled with a consumer fridge.
➝ Flammable material (alcohol, benzene, ether, LPG, etc) : possibility of
explosion.
5
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
Read all instructions before repairing the product and follow the instructions in order to prevent danger or
property damage.
CAUTION/WARNING SYMBOLS
DISPLAYED SYMBOLS
means “Prohibited”.
Indicates that a
Warning danger of death
or serious injury
means “Do not disassemble”.
exists.
means “No contact”.
Ra
comp ted
onen
ts
Unplug
On repair, remove completely dust or other After repair, check the assembled state Check if there is any trace indicating the
things of housing parts, harness parts, and of components. permeation of water.
check parts. • It must be in the same assembled state when • If there is that kind of trace, change the related
• Cleaning may prevent the possible fire by tracking compared with the state before disassembly. components or do the necessary treatment such as
or short. taping using the insulating tape.
Earth
6
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
Do not allow users to plug several Do not allow users to disassemble, Do not allow users to bend the power
appliances into the same power repair or alter. cord with excessive force or do not
receptable. • It may cause fire or abnormal operation have the power cord pressed by heavy
• May cause abnormal generation of heat or which leads to injury. article.
fire. • May cause fire.
Prohibited Do not
disassemble
Do not allow users to store articles on Do not allow users to install the In order to reduce the risk of electric
the product. refrigerator in the wet place or the shock the appliance must be
• Opening or closing the door may cause things place where water splashes. properly grounded.
to fall down, with may inflict a wound. • Deterioration of insulation of electric parts
may cause electric shock or fire.
Prohibited Earth
7
This document cannot be used without Samsung's authorization
Precautions(Safety
2. PRODUCT SPECIFICATIONS
Warnings)
Large Capacity
• The Samsung Side by side Refrigerator has a very spacious interior with a huge
Capacity. Thinner wall with its special high-urethane insulation technology
and . So there’s plenty of room in the drawers and shelves of the fridge and
freezer to store your weekly grocery shopping, including items of various
shapes or sizes.
And it’s much easier to keep everything neatly and efficiently organized.
So you can quickly find and take out the things you need whenever you need
them.
LED Lighting
• This space-saving LED fixture illuminates every corner of the fridge, so things
are easier to find. Also LED emits less heat than conventional bulb lighting,
affecting less damage to the temperature management.
8
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
• Multi Airflow
Provides even cooling throughout the refrigerator to maintain optimal temperatures to keep food
fresh.
• LED Lighting
See everything in a new light with LED lighting.
9
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
12
11
08 04
05
01
02 07
06
03
09
01 Freezer shelves 02 Multipurpose freezer bin 03 Dried food and meat storage drawer
NOTE
The design of the egg container may differ with the model.
10
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
12
11
10
08
04
05
01
09
02 07
03 06
01 Freezer shelves 02 Multipurpose freezer bin 03 Dried food and meat storage drawer
NOTE
The design of the egg container may differ with the model.
11
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
12
11
08
04
05
01
02 07
06
03
09
01 Freezer shelves 02 Multipurpose freezer bin 03 Dried food and meat storage drawer
NOTE
The design of the egg container may differ with the model.
12
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
12
11
04
05
01
09
08
02 07
03 06
01 Freezer shelves 02 Multipurpose freezer bin 03 Dried food and meat storage drawer
NOTE
The design of the egg container may differ with the model.
13
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
ITEM Specification
RS68N8222** RS68N8322**
Model RS 68N8220** RS68N8320** RS67N8210** RS66N8100** RS68N8221** RS68N8331** RS67N8211** RS66N8101** RS6GN8222** RS68N8242** RS6 GN8322**
RS68N8232** RS6GN8332**
Image
Gross capacity
664 664 652 682 664 664 652 682 664 664 664
(LT)
Freezing
Valid
compartment 237 237 234 255 237 237 234 255 237 237 237
net
(LT)
capacity
Cold
compartment 427 427 418 427 427 427 418 427 427 427 427
(LT)
Dimensions
W912*D716*H1780 W912*D772*H1780 W912*D716*H1780 W912*D772*H1780 W912*D716*H1780
(width x depth x height)
Dimensions of package
W960*D776*H1912
(width x depth x height)
Rated frequency (Hz) 50 or 60
Rated voltage (V) 220 ~ 240 or 110 ~ 127
Rated power
consumption of motor 170 ← ← ← ← ← ← ← ←
(W)
Rated power
200
consumption of heating ← ← ← ← ← ← ← ←
(AC 230V, 120 V)
device (W)
Refrigerator type Indirect Cooling Refrigerator
Refrigerant R-600a
Refrigerant charging
71g ← ← 74g ← ← ← ← ←
volume
Product weight (kg) 118 ← ← 113 118 ← ← 113 118 ← ←
Weight of packaged
122 ← ← 117 122 ← ← 117 122 ← ←
product (kg)
14
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
Items Specification
RS68N8222**
RS68N8232**
RS68N8242**
RS68N8220** RS67N8210** RS66N8100** RS68N8221** RS67N8211** RS66N8101** RS68N8322**
Model RS68N8320** RS68N8331** RS6GN8222**
RS6GN8322**
RS6GN8332**
Type NF54M5151ARAK3 ← ← NF54M7151ANAK3 ← ← NF54M9131AMAK3
Compressor Drive mode INVERTER
Charged oil SUNUSO-2GSD(250cc)
Freezer
Freezing Component
of F and R)
Defrosting Cycle
15
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
Items Specification
RS68N8222**
RS68N8232**
RS68N8242**
RS68N8220** RS68N8221**
Model RS68N8320** RS67N8210** RS66N8100** RS68N8331** RS67N8211** RS66N8101** RS6GN8222**
RS68N8322**
RS6GN8322**
RS6GN8332**
Power supplying during
Defrosting heater in freezing compartment AC230V,200W or AC120V,200W
freezing compartment defrosting
Defrosting heater in Power supplying during -
cold compartment cold compartment defrosting
Home bar heater Ambient humidity sensor -
(cold compartment) interlocking
Icemaker heater -
AC 230V,6W or AC 230V,6W or AC 230V,6W or
Dispenser heater - -
AC120V,6W AC120V,6W AC120V,6W
Water pipe heater DC12V 6W DC12V 2.3W - DC12V 6W DC12V 2.3W - DC12V 6W
Water tank heater -
Damper heater Kept tumed on -
Bimetal for preventing overheating of Thermostat (BT-121-M) On: 40°C, Off: 60°C
defrosting heater in freezing compartment
Bimetal for preventing overheating of -
defrosting heater in cold compartment
Type -
Electric Component
Operating temperature
OLP -
(°C)
Shutdown temperature -
(°C)
Cooling fan motor in freezing compartment DC12V, AIO Q7
Cooling fan motor in cold compartment DC12V, AIO Q7
Compressor cooling fan motor DC12V, C150Q
Motor-driven damper -
(True-taste chamber)
Motor step valve DC 12V,700mA
DC 12V,
DC 12V, DC 12V, 300mA
DC valve 300mA - - 300mA - - (RS68N8322**/
(RS68N8320**) (RS68N8331**) RS6GN8322**/
RS6GN8332**)
Precautions(Safety Warnings)
908mm (Cabinet)
716mm
763mm
10.5mm
1165mm
352mm
387mm 513mm
912mm (W. Cover Hinge)
0˚~165˚ 0˚~170˚
564mm
1726mm
716mm
1780
1725
1747
1741
55mm
17
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
908mm (Cabinet)
763mm
10.5mm
1165mm
352mm 470mm
387mm 513mm
912mm (W. Cover Hinge)
0˚~165˚ 0˚~170˚
564mm
1726mm
1741
55mm
18
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
For Plumbing
FILTER-WATER DA29-10105J 1
Model
19
This document cannot be used without Samsung's authorization
3-1. PRECAUTION
- NEED TOOL
Hexagon wrench
Use for adjust Door Hinge Ref Up.
(4mm diameter)
20
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
3-2. Interior-Fridge
Do not put the shelf on the place where wine rack is assembled. If the shelf is put on the
wine rack place, it may cause collision between the shelf and door bin when the door is
CAUTION
closed.
Shelf
Wine Rack
Drawer cover
Push
21
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
2. R
emove the inlet cover.
(Remove side hook 2ea)
R-Compartment
Duct & Eva Cover
Multi Duct
(Fridge)
2. D
isengage the housing Connector.
22
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
■ Assembly
Remove the Clip and input the Hose.
Water Filter
■ Disassembly
Remove the Hose by puching the Collet.
Be sure to flush the dispenser thoroughly (approx. 6 to 7 minutes), otherwise water may
CAUTION drip from the dispenser. This means that there is still air in the line.
23
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
3-5. Cover-Display
2
Remove the display cover by pulilng it up.
1
Cover-Display 1
24
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
25
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
■ Assembly
Assembling housing of Assy Case Ice Route
Upper 2 Rib have to match with inside Hook
and Screw assembling.
CAUTION
Upper Hook have to completely match with
Hook for prevent the leak of Gasket Cover.
ASSY GUIDE
ICE ROUTE
26
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
■ Disassembly
1. P
ut both fingers in the upper of lever.
Pull and remover the lever slowly.
■ Assembly
2. P
ut the lever with adjusting to rectangle
block slowly.
27
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
3-8. Interior-Freezer
Drawer Cover
Push
28
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
F-Compartment
2. Remove the Evap Cover from the
Duct & Eva Cover
cabinet.
Pull the Cover in the direction
of the front.
3. R
emove the Housing connector
(1ea).
29
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
2. R
emove the Housing connector
(1ea).
1. A
fter disengage the Evaporator
Cover- Freezer, Pull the Multi
duct Freezer in the direction of
the front.
Multi Duct
(Freezer)
※ Incabi only
2. R
emove the Housing connector.
(1ea)
30
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
31
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
CAUTION
Door Be careful not to pinch the water tubing
and the wire harness on the door.Lift up
the door straight in upper direction until
the water hose is eliminated from lower
hinge.Do not pull the door forward to
remove it. It cause injury of water hose
and tubing.
32
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
Door
33
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
※ Function of Screw
Adjust the door side leveling.
(0~0.9mm to right side using by Hexagon
wrench 4mm)
Door
34
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
• T
he Water Line must be fully inserted to the
center of transparent coupler (Type A) or
the line (Type B) to prevent water leakage
from the dispenser.
• Check that it holds the line firmly.
Reassembly
doors
• T
he cover hose must be fully covered water
hose. (Make the cover hose fit to end of the
fitting)
• B
ottom hook must fix the cover hose to
prevent loosen the hose line.
35
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
3-12. Evaporator
Figure
Part Name Description
Freezer Fridge
Evaporator
36
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
37
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
4. Cutting seal.
38
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
39
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
2. Remove 1 screw.
3. Remove 1 screw.
CAUTION
Cautions for R-600a : Environment-friendly gas (R-600a) is used as refrigerant at this refrigerator, which is
combustible gas though in volume kept small. If gas is leaked by serious damage to the refrigerator during
transportation, installation and operation may cause fire or burn when spark makes contact with leaked
gas.
40
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
Ice Bucket
Disassemble the Ice Bucket Assy by holding
Assy
the handle and pulling up
The bottom part slightly.
※indoor only
※indoor only
Disconnect the housing connectors by gently
pulling.
Assy Case
Auger Motor
(assemble)
※indoor only
Push the auger motor each side.
41
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
Assy Ice
Maker
Unscrew the 4 screws.
※indoor only
42
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
※incabi only
Pull out Assy Case Auger Motor gently.
Assy
Ice Maker
※incabi only
Disconnect the Assy Ice Maker housing.
43
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
2. Disassembly 2 screws.
Water tank
44
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
2. Disassembly 2 screws.
Water tank
※ indoor
Housing
3. Disconnect the housing and Pull out the
Hose.
45
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
Water tank
Housing
4. Disconnect the housing and Pull out the
Hose.
46
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
LED Lamp
(Fridge)
2. Pulling it to the direction of the arrow on
the left.
47
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
LED Lamp
(Freezer) 2. Remove the connector from the LED
by lifting and then pulling it to the
direction of the arrow on the right.
48
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
LED Lamp
(Fridge)
2. Pulling it to the direction of the arrow on
the left.
49
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
LED Lamp
(Freezer)
50
This document cannot be used without Samsung's authorization
4. TROUBLESHOOTING Warnings)
Precautions(Safety
01 06 02 03 04 05
01 06 02 03 05
01 06 02 05
01 Freezer / Power Freeze (3 sec) 02 Fridge/ Power Cool (3 sec) 03 Ice Maker (3 sec) *
51
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
03 Ice Maker
Press and hold Ice Maker for more than 3 seconds to turn the ice
maker on or off.
The ice maker has 2 indicators (ON/OFF) to indicate the operating
status.
• When the ice maker operates, the ON indicator turns on.
• When the ice maker is turned off, the OFF indicator turns on. In
Ice Maker
this case, ice making is disabled even if you press the Cubed Ice or
Crushed Ice buttons on the dispenser panel. To enable ice making,
you must turn the ice maker on.
NOTE
• If the ice maker is turned off, it will turn on if you press and hold
the ice lever for more than 5 seconds.
• After tuning off the ice maker by inside cabinet control panel,
this function doesn't work for 1 minute.
52
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
above.
You can set the alarm for a reminder. If the door is left open for more
than 2 minutes, the alarm will sound with the alarm indicator blinking.
Door Alarm
The alarm is enabled by factory default. To disable the alarm, press
Door Alarm. To enable, press Door Alarm again.
The Vacation button can be used to activate/deactivate Vacation mode.
If you are going on vacation or a business trip, or if you do not intend
to use the refrigerator for an extended time, use the Vacation feature.
Press and hold Vacation for 3 seconds to turn off the fridge operation
Vacation with the Vacation indicator ( ) on.
NOTE
It is strongly recommended to empty the fridge compartment and
make sure the door is closed.
If this happens, contact your Internet service provider for technical assistance.
•
Refrigerator from accessing the Internet. Contact your Internet service provider for
technical assistance. If this symptom continues, contact a local Samsung service center
or retailer.
•
• Samsung Smart Refrigerators featuring the Samsung Smart Home Dongle support
both Wi-Fi 2.4 GHz with IEEE 802.11 b/g/n and Soft-AP protocols (IEEE 802.11 n is
recommended).
• Unauthorized Wi-Fi wireless routers may fail to connect to applicable Samsung Smart
Refrigerators.
53
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
54
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
NOTE
The Lock on the dispenser panel does not affect the controls on the
main panel. To lock the main panel, use the Control Lock function on
the main panel.
02 Cubed Ice
Cubed Ice Press Cubed Ice to dispense cubed ice.
The corresponding indicator turns on.
03 Crushed Ice
Crushed Ice Press Crushed Ice to dispense crushed ice.
The corresponding indicator turns on.
55
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
■ Installation
Visit the Google Play Store, Galaxy Apps, or Apple App Store and search for “SmartThings”.
Download and install the SmartThings app provided by Samsung Electronics to your smart device.
NOTE
• The SmartThings app is designed for Android 6.0 (Marshmallow) or later, iOS 10.0 or later, iPhone 6 or
later, and is optimized for Samsung smartphones (Galaxy S and Galaxy Note series).
• For improved performance, the SmartThings app is subject to change without notice, or discontinued
support according to the manufacturer’s policy.
Samsung account
You are required to register with a Samsung account to use the app. If you don’t have a Samsung account,
follow the app’s onscreen instructions to create a free Samsung account.
Getting started
1. Insert the Smart Home Dongle into the corresponding port of your refrigerator.
2. R
un the SmartThings app and log in with your Samsung account. iPhone users are required to provide
the login information each time they access the app.
3. Access Add Device and then tap Refrigerator.
4. Follow the onscreen instructions to provide the necessary information about the router, and then tap
Next.
5. P
ress and hold Fridge for more than 5 seconds until the "AP" message appears on the display.
Your refrigerator will be registered with the app.
6. When device registration is complete, the refrigerator icon will appear on the SmartThings app.
7. Tap the refrigerator icon to open the refrigerator page.
8. When a network connection is established, the Wi-Fi icon lights up on your refrigerator.
■ Refrigerator app
Integrated control
You can monitor and control your refrigerator at home as well as while on the move.
• Tap the refrigerator icon on the SmartThings to open the refrigerator page.
• Check the operation status or notifications for your refrigerator, and change options or settings if
necessary.
NOTE
Some options or settings of the refrigerator may not be available for remote control.
56
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
■ Wi-Fi connection
You can control the refrigerator remotely using the Smart Home Dongle that is sold separately.
To purchase the Smart Home Dongle, visit www.samsung.com and follow the product information about
the dongle.
NOTE
• You may not be able to purchase the Smart Home Dongle separately in some countries.
Please check with your dealer for availability.
CAUTION
• The Samsung Smart Home Dongle comes in two types: one that is dedicated to Samsung smart TVs, and
the other one that is dedicated to Samsung home appliances.
• You must purchase the Samsung Smart Home Dongle (HD39N1230GW) dedicated to home appliances.
Any other dongles may cause system failure.
NOTE
The marked area is the cover of the optional dongle, not a
crack or defect.
57
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
CAUTION
• The refrigerator must be levelled on a flat, solid floor. Failing to do so can cause damage to the
refrigerator or physical injury.
• Levelling must be performed with an empty refrigerator. Make sure no food items remain inside the
refrigerator.
• For safety reasons, adjust the front side a little higher than the rear side.
The refrigerator can be levelled using the front legs that have a special screw (leveller) for levelling
purposes. Use a flat-head screwdriver for levelling.
58
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
1. O
pen the door to adjust, and locate the two nuts
(A) and (B) on the front bottom of the door.
59
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
CAUTION
• M
ake sure you connect the coupler to the cold water tap. Connection to the hot water tap may cause the
water filter to be clogged and fail to operate normally.
• T
he warranty for your refrigerator does not cover the water line installation. The water line installation
will be performed at your own costs unless the installation fee is included in the retailer’s price.
• S
amsung takes no responsibility for the water line installation. If water leaks occur, contact the installer
of the water line.
• T
he water line must be repaired by a qualified professional. If you encounter a water leak, contact a local
Samsung service centre or the installer of the water line.
60
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
CAUTION
• T
he water line must be connected by a qualified technician.
• T
he warranty for your refrigerator does not cover the water line installation. The water line installation
will be performed at your own costs unless the installation fee is included in the retailer’s price.
• S
amsung takes no responsibility for the water line installation. If water leaks occur, contact the installer
of the water line.
CAUTION
• M
ake sure the water filtering hose is connected to a cold, potable water source pipe.
Connecting to the hot water pipe may cause the water filter to malfunction.
1. S
hut off the water supply by closing the main water
valve.
2. Locate the cold, potable water pipe (1).
3. F
ollow the Water Line Installation to connect to the
water pipe.
NOTE
New hose-sets supplied with the appliance are to be used
and old hose-sets should not be reused.
61
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
1. L
oosen and remove the compression nut (a) from
the water line of the refrigerator, and insert it to
the water filtering hose.
2. T
ighten up the compression nut (a) to connect the
water filtering hose and the water line.
3. O
pen the main water valve and check for any
leaks.
4. I f there are no leaks, dispense about 10 litres
of water or dispense the water for 6 - 7 minutes
before actually using the refrigerator to remove
impurities inside the water filtering system.
5. S
ecure the water line to a sink or a wall using a
clip.
CAUTION
• D
o not tighten the water line excessively. Make sure the
water line is not bent, pinched, or squashed.
• D
o not mount the water line on any part of the
refrigerator. This may damage the refrigerator.
NOTE
If you have to relocate the refrigerator after connecting
the water line, make sure the joined section of the water
line must is straight.
CAUTION
The water line must be repaired by a qualified professional. If you encounter a water leak, contact a local
Samsung service centre or the installer of the water line.
62
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
The water pressure of the water supply system to a reverse osmosis water filtration system must
be between 241 kPa and 827 kPa.
The water pressure of the reverse osmosis water filtration system to the refrigerator’s cold water
line must be at least 276 kPa. If the water pressure is below the specified:
• C
heck if the sediment filter in the reverse osmosis system is blocked. Replace the filter if
necessary.
• R
efill the water tank in the reverse osmosis system with water.
• I f your refrigerator has a water filter, it may further reduce the water pressure when used in
conjunction with a reverse osmosis system. Remove the water filter.
To purchase a new water filter (part type: HAFEX/EXP), contact a local Samsung service centre.
NOTE
If the filter is installed horizontally, water may remain in
the filter. Therefore, vertical installation is recommended.
CAUTION
Do not mount the water filter on any part of the
refrigerator. This may damage the refrigerator.
63
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
CAUTION
• D
o not use third-party water filters. Use only Samsung-provided or -approved filters.
• U
napproved filters may leak and damage the refrigerator, causing electric shock.
Samsung holds no responsibility for any damage that may occur from use of third party water filters.
• The filter indicator turns red as a reminder that lets you know it is time to replace the water filter.
1. S
hut off the main water supply.
2. C
onnect the water supply line to the inlet side of
the filter to the end.
3. C
onnect the dispenser line to the outlet side of
the filter.
4. C
heck if there is any leak. If not, fix the lines with
the clips.
5. P
ut the water filter into place and fix it with the
clips.
6. P
ress and hold Filter Reset for 3 seconds to reset
the filter lifecycle.
7. W
hen replacing is complete, flush 10 litres of
water (or dispense the water for 6 - 7 minutes) to
remove impurities from the water line.
CAUTION
When adjusting the length of the water line tubing, make
sure to smooth out the cut surface at a right angle.
This is to prevent a water leak.
NOTE
• A
newly installed filter may cause the water dispenser to spurt water briefly. This is because air has
entered the water line.
• T
his replacement process may involve the refrigerator to drip water onto the floor. If this happens, wipe
up with dry cloths.
64
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
ꞏ I f Freezer Key + Alarm Key ard pressed simultaneously for 6 seconds, ALL ON/OFF will blink with 0.5 interval for
4 seconds. If take the finger off from above keys and press Alarm key.
ꞏ I t will be changed to the test mode and all displays on the front of panel will be off.
ꞏ I f any key on the front of panel is pressed within 15 seconds after the test mode, it will be operated as below sequence :
Manual operation (FF) → manual operation (FF-r) → manual operation (FF-F) → manual operation (FF-A) → manual defrost of
fridge compartments(rd) → manual defrost of freezer compartment(Fd) → cancel(Display all off)
ꞏ I f any key on the front of panel is not pressed within 15 seconds after the test mode, the test mode will be canceled and it will be
returned to previous mode.
2) Forced Defrost
- Rd : Forced Fridge Compartment defrosting (rd) begins, a beeping sound will be heard for 2 seconds and then the sound will
be turned on for 0.1 seconds and then off for 0.9 seconds repeatedly while the Forced defrosting function runs.
- Fd : F orced Freezing, Fridge Compartment defrosting (Fd) begins, a beeping sound will be heard for 2 seconds and then the
sound will be turned on for 0.5 seconds and then off for 0.5 seconds repeatedly while the Forced defrosting function runs.
65
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
66
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
■ Self-diagnostics check list
F R
LED
Item Trouble contents Diagnostic method Image
F R
67
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
■ Self-diagnostics check list
LED
Item Trouble contents Diagnostic method Image
F R
Separation of freezer
After separating Main PCB
compartment defrost heater
CN70& SMPS CN01 wire from
housing part, contact error,
PCB, Resistance value between
disconnection, short circuit
CN70 9PIN - SMPS CN01
or temperature fuse error.
F-DEF Error 3PIN Shall be 63(230) ohm ±
Display error : the defrosting
7%(Resistance value is varied
does not finish though
by input power) 0 ohm : heater
freezer compartment defrost
short, ∞ ohm : wire/bimetal
is heating continuously for
open (Must power off)
more than 100 minutes.
68
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
LED
Item Trouble contents Diagnostic method Image
F R
Actually, If there is not a
Dispenser
problem, it is desirable to
Panel ↔ Main MICOM MAIN ↔ DISPENSER
replace Main and Panel PCB
Communication PANEL communication error.
With the oscilloscope after a
Error
cable problem confirming.
69
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
1) If Freezer Key + Alarm Key are pressed simultaneously for 6 seconds during normal operation, the temperature setting display
of fridge and freezer compartments will blink ALL ON/OFF with 0.5 for 4 seconds.
2) If take the finger off from above keys and press Fridge key load status will display.
At LED all on state only load condition display will blink ON/ OFF with 0.5 seconds interval.
3) Load condition display mode shows the load that micom signal is outputting.However, It means that micom signal is
outputting, it does not mean whether load is operating or not. That is to say that though load operation is displayed, load could
not be operated by actual load error or PCB relay error etc. (This function would be applied at A/S.)
4) Load condition display function will maintain for 30 seconds and then normal condition will be returned automatically.
5) Load condition display is as below. Only the load control LED will blink with 0.5 interval in "Display LED".
70
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
11 F-FAN HIGHEST F-1-ⓑ,ⓒ When F-FAN HIGHEST operates, applicable LED blinks.
12 F-FAN HIGH F-1-ⓑ When F-FAN HIGH operates, applicable LED blinks.
71
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
4-4-5. Exhibition mode setting function (All Regions Except for North America)
1) I f Fridge Key + Alarm Key are pressed simultaneously for 6 seconds, ALL ON/OFF will blink with 0.5 interval for
4 seconds. If take the finger off from above keys and press Freezer key, Exhibiton mode will be started with buzzer
sound.
2) I f above Exhibition entering Key are pressed one more time, Exhibition mode will be canceled.
3) If Exhibition mode is selected or canceled by key, displays "on" or "oF" for 5 seconds on the temperature setting display
of the panel and it indicates the refrigerator has entered or exited the Exhibition mode.
After 5 seconds, the display panel will work normally.
4) D uring Exhibition mode, if fridge and freezer compartments sensors are higher than 65°CExhibition mode will be
canceled automatically and freezing operation will be returned. (There is no buzzer sound when the Exhibition mode is
canceled by the Temperature.)
5) Operation contents of Exhibition mode
- Display, Fan motor and etc operate normally, not to operate compressor and Door Open Alarm.
- Defrost is not operated. (including french heater)
- Display function of the initial real temperature is finished.
- Under the condition of Exhibition mode, Exhibition mode will be canceled when Power On after Power OFF.
72
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
1) This function is to display the MAC address of the Refrigerator Wi-Fi module, and consecutively displays the MAC
address on the Freezer (F Compartment) Temperature Display Part for one minute.
- If you press the Freezer button and the Fridge button simultaneously for six seconds or longer,
the Display will blink.
Here, if you press the Freezer button, a buzzer sound will be made and the product will enter the MAC
Address Display Mode.
2) If the MAC address is "11-22-33-44-55-66," "--," "11," "22," ... "66," and "--" will be repeatedly displayed on the
Freezer Temperature Display Part for one minute.
When one minute has passed, the MAC Address Display Mode will be canceled with a buzzer sound, and the
product will return to the normal Display Mode.
※ I f the MAC address is not valid or the WI-Fi module is not connected, "--" will be displayed on the Freezer Display
Part for one minute.
73
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
I f Freezer Key + Alarm Key are pressed simultaneously for 6 seconds during mormal operation, ALL ON/OFF will
blink with 0.5 interval for 4 seconds. If take the finger off from above keys and press Freezer, Fridge and Freezer
compartments temperature display will be changed to operion setting mode.
• If the display changes to option setting mode, all displays will be off except freezer and fridge
compartments temperature display as below.
(Fridge and freezer compartments case will be explained only because all options are operated with
the same method according to the option table.)
74
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
Basically, all the data in option has cleared from the factory.
Therefore, almost all setting value are "0".
But, some setting values could be changed for the purpose of improving performance.
NOTE
Code You need to check
Reference the product manual and/or specification.
Value
2) After changing to the option mode, fridge compartment "0" , freezer compartment "0" will be displayed.
( Basically fridge compartment "0", freezer "0" would be set at shipping process, but setting value could be
changed for the purpose of improving product at mass producing process.)
- I f fridge compartment "0" shows only, temperature reference value of freezer compartment will be set
Codefreezer
and current Reference Value
compartment temperature code will be displayed on the freezer temperature display.
3) If freezer compartment "4" is set as below freezer compartment code after fridge compartment "0 is set,
standard temperature of freezer compartment will be lower than -2°C.
(Refer to the picture "changing the freezer compartment temperature")
75
Code Reference Value
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
Setting value
FZ Code Reference Value
Temp.
compartment
compensation
Code
0 0.0°C
1 -0.5°C
2 -1.0°C
3 -1.5°C
4 -2.0°C
5 -2.5°C
6 -3.0°C
7 -3.5°C
8 +0.5°C Code Reference Value
9 +1.0°C
10 +1.5°C
11 +2.0°C
12 +2.5°C
13 +3.0°C
14 +3.5°C
15 +4.0°C
Setting value
FZ ex) If you want to change the
Temp.
compartment Fridge compartment standard
compensation
Code temperature to 2°C.
0 0.0°C
1 -0.5°C
2 -1.0°C Code Reference Value
3 -1.5°C
4 -2.0°C
Code Reference Value
5 -2.5°C
6 -3.0°C
7 -3.5°C
8 +0.5°C
9 +1.0°C
10 +1.5°C
11 +2.0°C
12 +2.5°C
13 +3.0°C Code Reference Value
14 +3.5°C
15 +4.0°C Code Reference Value
76
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
3) Ice Tray water supply of freezer compartment Ice Maker (In DISPENSER MODEL with flow
sensor Only features)
Set item FZ-Room ICE TRAY
Reference Fridge Room 7-SEG
Value 2
Setting value
FZ
Water
compartment
Settings.
Code
0 92cc
1 105cc
4) Eject waiting time changing table of freezer compartment Ice Maker (In DISPENSER MODEL
Only features)
Set item FZ-Room Ice Maker Eject waiting time Shift
Reference Fridge Room 7-SEG
Value 3
5) Eject temperature changing table of freezer compartment Ice Maker (In DISPENSER
MODEL Only features)
Setting value
FZ
Temp.
compartment
compensation
Code
0 -17.0°C
1 -16.0°C
2 -15.0°C
3 -14.0°C
4 -13.0°C
5 -12.0°C
6 -18.0°C
7 -19.0°C
77
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
6) M
inimum Comp RPM shifting.
- This option is rising minimum Comp RPM.
As this option is applied, Comp operation.
Set item Minimum Comp RPM setting
Reference Fridge Room 7-SEG
Value 12
Setting value
FZ
compartment Comp RPM
Code
0 No RPM Change
1 Minimum 2450RPM
2 Minimum 2450RPM
3 Minimum 2450RPM
7) T
emp Display Option.
- This option is for temp display all on mode.
If user wants temp display always on, this option is solution.
Setting value
FZ
compartment Temp Display Option
Code
Normal Display (Temp display
0
temporally on at use)
1 Always Temp Display On
2 Always Temp Display On
78
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
Setting value
FZ compartment
Rate change
Code
0 +0.0%
+ 20%
1 operation
( up to 100% )
9) Temperature changing table of Flex Room compartment. (in FLEX ROOM Model Only features)
Setting value
FZ
Temp.
compartment
compensation
Code
0 0.0°C
1 -0.5°C
2 -1.0°C
3 -1.5°C Code Reference Value
4 -2.0°C
5 -2.5°C
6 -3.0°C
7 -3.5°C
8 +0.5°C
9 +1.0°C
10 +1.5°C
11 +2.0°C
12 +2.5°C
13 +3.0°C
14 +3.5°C Code Reference Value
15 +4.0°C
79
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
DATA1.Temperature table
Resistance value and MICOM port voltage of sensor according to the temperature
SENSOR CHIP : b ased on PX41C, PX41C, 502AT/ 103**(ICE MAKER SENSOR(MOLD)/FULL UP, 20Kohm
( Actual measurement = value of the table below X 2 )
80
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
81
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
Output terminal
1. 12V
2.12V
3. GND
4. GND
5. 5V
Input terminal
Yes
Connect the plug, or correct loose plug.
Is normal voltage of 12V No
Checking voltage at and 5V generated on SMPS
SMPS output terminal?
Yes
PCB assembly replacing.
No
Is operation of panel
PCB normal?
1) Checking and repair of power cable
Yes assembling.
Yes 2) Panel PCB replacing.
Is soldering short or
cracked on PCB?
82
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
Start
F-DEF Sensor is NO
normal (with Self Diagnosis)
Replace the sensor.
YES
NO
F-DEF Heater is normal
CN70
YES
NO It goes
back to Cooling Operation after
heating
Check all the sensors
YES
Note Normal
When F-DEF Sensor is higher than
+10℃ and +17℃, it will stop heating
and go back to Cooling Operation.
MAIN PBA NO
connectors are normal.
@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@
YES Repair the connectors
cnSP@CT@@CW cnSP@CQ@@CT
Precautions(Safety Warnings)
When there is sensor error, display panel show that. When it occurs during the initial power on time, display
panel keeps blinking relevant 7-SEG and the refrigerator go into the emergency operation mode.
Under the emergency operation mode, the refrigerator can not do its normal operation. So check out with the
Self Diagnosis in this manual.
Start
MAIN PBA NO
connector (CN30) is inserted
properly.
Repair the defective contact
YES CN30
CN30 of the connector or insert
the connector properly
Ambient Tem p Sensor NO
is ok.
Ambient-Sensor : Read the
resistance between CN30 #1
and #2
YES
Compare the room temp.
with sensed temp. using PBA & Thermistor are ok. Replace Thermistor.
Temp-Resistance Table. Check the contact of the
connector again.
2) When the Fridge Temp Sensor is defective (also applied to other sensors)
Start
84
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
85
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
This model has a buzzer on the Panel PBA. If the buzzer does not sounds when button is pressed,
Forced Operation, door open and disconnection with Main PBA, check out defective soldering on
PBA or buzzer damage. (It is recommended replacing Panel PBA if components are damaged)
※ It could be unable to hear in case there is heavy noise or built-in environment.
Start
"DingDong"
Sounds when a button on the NO
display panel is pressed
NO Normal
The Buzzer
surface is broken/bended. YES
Or Buzzer lead comes off from
the vibration plate.
Buzzer Breakage
NO Replace Buzzer.
Check
the wiring - short / open YES
(buzzer ↔ Display in fridge)
86
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
YES
Child Lock is on
87
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
- This model has BLDC FAN motor. BLDC motor is driven by DC7~12V
- F-Fan motor usually runs together with the Compressor. Once the door is open and closed at high
ambient temperature, F-Fan motor put off its operation for one minute. Therefore, you are advised not to
take it as an error.
- When fridge door is open, the F-Fan motor stops.
Start
NO
COMP is on?
For R-Fan For C-FAN For F-Fan YES Run Forced Operation.
88
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
4-5-7. When the internal lamp of the freezer/fridge does not light up
1. Turn off the power for repair because there is risk of electric shock when replacing the internal lamp.
2. Please keep in mind you could get burnt by the excessive heating of an incandescent light bulb.
Reference
Reference
1. When the DOOR is open, the DOOR S/W becomes OPEN. Micom senses 5V from Door S/W and recognizes that
the Door is open. If 5V has sensed for more than 2 minutes, buzzer will sounds “DingDong” every 1 minute.
Therefore, if the DOOR S/W is defective, it can generate the “Ding Dong” sound every 1 minute.
2. ON/OFF control of the internal lamp is linked with the DOOR S/W.
Start
89
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
Protecting
LED Blinking Frequency Remarks
Functions
Normal
N/A
Operation
90
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
"[refrigerator] Samsung"
appears from the AP List in
SET AP mode.
91
This document cannot be used without Samsung's authorization
5. PCB DIAGRAM
Precautions(Safety Warnings)
Ⓖ Ⓗ Ⓘ
Ⓕ
Ⓔ Ⓒ
Ⓙ Ⓑ
Ⓓ
92
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
B
D
1. PCB Power Supply : From the AC Input Voltage(115V/220V), it supplies DC 15V and 5V to the Inverter
circuit for the Compressor control.
2. COMP Driving / Feedback Circuit
It receives the COMP operation signals from the Main PBA and feedbacks the inverter errors to the
Main PBA.
3. Micom (MN103SFC2D)
4. BOOTSTRAP Charger : It is an independent power circuit for the driving of the IPM High-Phase IGBT.
5. Current Pickup Circuit : It pickups the currents taken by the Shunt resistance and does the PWM
DUTY control.
6. IPM (FNB40560)
93
CN11
1: 12V 2: 12V 3: GND 4: GND
CN70_2 5: 5V 6: 5V 7: GND
1: WATER PIPE HEATER 8: DISPENSER DISPLAY TX
3: WATER STOP VALVE 9: DISPENSER DISPLAY RX
CN70_1
CN74
1: F -DEF HEATER
1: GND 2: C -FAN 3: R -FAN 4: F -FAN
3: R-DEF HEATER
5: ICE MAKER PUMP MOTOR
6: WATER PUMP MOTOR
CN70
7: NC 8: NC 9: F -FG 10: R-FG 11: C-FG
1: COM1
3: COM1
CN40
5: SUB HEATER
1: WATER LEVER 2:ICE LEVER
3: ICE BUCKET REED S/W
CN71_1 4: CUBE MOTOR REED S/W 5: ICE ROUTE 1
1: WATER SOLENOIDE VALVE 6 ICE ROUTE 2 7: GND
3: DISPENSER HEATER #1
5: DISPENSER HEATER #2
CN50
1: (DISPLAY IN FRIDGE) TX
CN71 2: (DISPLAY IN FRIDGE) RX
1: CUBE SOLENOIDE VALVE 3: 12V 4: 5V 5: GND
Precautions(Safety Warnings)
94
CN90
CN73 1: I/M MOTER 2: I/M MOTER
1: CUBE MOTOR 3: I/MSENSOR 4: TEST SWITCH
3: AUGER MOTOR 5: HALL IC 6: NC
7: NC 8: 5V
5-3. Connector Layout with part position (Main Board)
CN30
CN13 1: GND 8: GND
1: (INVERTER) RX 2: EXT-SENSOR 9: NC
2: GND 3: F-SENSOR 10 : FLEX ZONE SENSOR
3: (INVERTER) TX 4: F-DEF-SENSOR 11 : HUMIDITY-SENSOR(EXT)
4: NC 5: R-SENSOR
5: (DISPENSER DIPLAY) 12V 6: R-DEF-SENSOR
6: 5V 7: GND
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
5-4. Connector Lay out with part position (LC3_3050 Inverter PBA)
5-4-1. 220V
AC IN UVW
1 : DC 5V
2 : GND
3 : COMP. RPM
4 : COMP. Feedback
5-4-2. 110V
AC IN UVW
1. DC 5V
2. GND
3. COMP RPM
4. COMP FEEDBACK
95
This document cannot be used without Samsung's authorization
6. WIRING DIAGRAM
6-1. Model : 2 Door, In-Door Ice Maker (RS68N82*, RS68N83*, RS6GN82*, RS6GN83*)
96
This document cannot be used without Samsung's authorization
Wiring Diagram
97
This document cannot be used without Samsung's authorization
Wiring Diagram
98
DISPENSER + INDOOR I/M + PLUMBING
AC 12V 5V DC220V Communication
AC INPUT
AC SMPS
EMI-FILTER
INPUT
MAIN PBA
SMPS
AC LOAD (12V,5V) INV COMP EEPROM
RESET OSCILLATOR
CONTROL(UART) (DIODE OPTION)
7. BLOCK DIAGRAM
F-DEF HEATER
DISPENENSER HEATER
MICOM
WATER SOLENOIDE VALVE
COMP EEPROM
ICE SOLENOIDE VALVE TEST MODE
CONTROL CONTROL
INVERTER CONTROL UART UART
ICE ROUTE MOTOR COMMUNICATION
CONTROL
AUGER MOTOR INV LOAD NORMAL MODE
MICOM
COMP CONTROL CONTROL UART UART
CUBE MOTOR CONTROL COMMUNICATION
SWITCH CONDITIONAL
INPUT CONTROL UART
7-1. DISPENSER + INDOOR I/M + PLUMBING
MATRIX
CONTROL COMMUNICATION
AC CONTROL
99
CIRCUIT ICE-MAKER A/D
CONTROL CONVERTER
12V DC LOAD DC CONTROL
CIRCUIT
COMP COOL PWM FAN 5V
AC INPUT
AC SMPS
EMI-FILTER
INPUT
MAIN PBA
SMPS
AC LOAD
Block Diagram
100
CIRCUIT ICE-MAKER A/D
7-2. DISPENSER + INDOOR I/M + NON-PLUMBING
CONTROL CONVERTER
12V DC LOAD DC CONTROL
CIRCUIT
COMP COOL PWM FAN 5V
AC INPUT
AC SMPS
EMI-FILTER
INPUT
MAIN PBA
SMPS
AC LOAD
Block Diagram
101
CIRCUIT ICE-MAKER A/D
CONTROL CONVERTER
12V DC LOAD DC CONTROL
CIRCUIT
COMP COOL PWM FAN 5V
AC INPUT
AC SMPS
EMI-FILTER
INPUT
MAIN PBA
SMPS
AC LOAD
Block Diagram
MICOM
COMP EEPROM
CONTROL TEST MODE CONTROL
INVERTER CONTROL UART UART
CONTROL COMMUNICATION
INV LOAD NORMAL MODE
MICOM
COMP CONTROL CONTROL
SWITCH CONDITIONAL
INPUT CONTROL UART MATRIX
CONTROL COMMUNICATION
AC CONTROL
102
CIRCUIT A/D
CONVERTER
12V DC LOAD DC CONTROL
CIRCUIT
COMP COOL PWM FAN 5V
F-DEF SENSOR
R-DEF SENSOR
AMBIENT SENSOR
WIFI
DONGLE READY
This document cannot be used without Samsung's authorization
Block Diagram
103
This document cannot be used without Samsung's authorization
Digit 1 2 3 4 5 6 7 8 9 10 11 12 13 14
Type Capacity Series I Year Series II Exterior Option Interior Option Energy Color /
Model
Code R S 6 8 N 8 6 7 1 S L / E U
■ Series (Digit 4)
Option
I &W Dispenser Ice Maker Handle
8 ○ Indoor I/M Recessed Handle
7 ○ Normal I/M Half Bar Handle
6 - Twist I/M Half Bar Handle
104
272, Oseon-Dong, Gwangsan-Gu,
Gwangju-City, Korea, 506-253
TEL: 82-62-950-6193, 6896
FAX: 82-62-950-6859