PDF of Proposed Museum Project

Proposed Museum Project
Form-1, Form -1A & Conceptual Plan,

for Environmental Clearance of the
Proposed Museum Project
at
Bhairon Marg, Behind Purana Quila, New Delhi
Submitted By
National Museum of Natural History
CONSULTANT
Ascenso Management & Consulting Services Pvt. Ltd.

A QCI Accredited Environmental Consulting Organization
Proposed Museum building complex at Bhairon Marg, behind Purana Quila, New Delhi by
National Museum Of Natural History
APPENDIX -I
(See Paragraph – 6)
FORM-1
(I) Basic Information
S. No. Item Details
1. Name of the project Proposed Museum building complex
2. S. No. in the Schedule 8 (a)
3. Proposed Total Plot Area: 26,299 sq.m.
capacity/area/length/tonnage to be Built up Area (FAR + Non FAR): 46,025.78 sq.m.
handled/command area/lease area/
number of wells to be drilled.
4. New/Expansion/Modernization New Project
5. Existing Capacity/Area etc. Not Applicable
6. Category of Project i.e. ‘A’ or ‘B’ B
7. Does it Attract the general condition? No
If yes, please specify.
8. Does it attract the specific condition? No
If yes, please specify.
9. Location
Plot/Survey/Khasra No Bhairon Marg, Behind Purana Quila
Village
Tehsil
District New Delhi
State Delhi
10. Nearest railway station/airport along Nearest railway station is New Delhi Railway Station
with distance in kms. at an aerial distance of approx. 4 km towards NNW.
Nearest Airport is Safdarjung Airport at an aerial
distance of approx. 4.78 km towards Southwest.
11. Nearest Town, City, District District Headquarters- New Delhi.

Headquarters along with distance in
kms.
12. Village Panchayats, Zilla Parishad, New Delhi Municipal Council, Palika Kendra,
Muncipal Corporation, Local body Parliament Street, New Delhi - 110001
(Complete postal addresses with
telephone nos. to be given)
13. Name of the applicant National Museum of Natural History
14. Registered Address FICCI Auditorium, Barakhamba Road , New Delhi
Consultant-Ascenso Enviro Pvt. Ltd. Page 1 of 17

15. Address for correspondence:

Name Mr. Chandra Prakash Sharma
Designation(Owner/Partner/CEO) Executive Engineer
Address CED-1, CCU, MoEF&CC, Room No. 722,

Paryavaran Bhawan, CGO Complex, Lodhi Road,
New Delhi
Pin Code 110003
E-Mail eecpsharma@gmail.com
Telephone No. 011-24363292
Fax No.
16. Details of Alternative Sites The land is allotted the Ministry of Environment,
Examined, if any, Location of these Forests and Climate Change, GOI by Ministry of
sites should be shown on a topo Urban Development, GOI vide letter no. L-IIA-
1(1377)/313 dated 18.12.2014. The copy of the letter
sheet.
is attached as Annexure-I.
17. Interlinked Projects No
18. Whether separate application of

interlinked project has been Not Applicable
submitted?
19. If yes, date of submission Not Applicable
20. If no, reason Not Applicable
21. Whether the proposal involves

approval/clearance under: If yes,
detail of the same and their status to
be given
(a) The Forests (Conservation) a.) No, since no l and protected under The Forests
Act, 1980? (Conservation) Act, 1980 is involved in the
project.
(b) The Wild Life (Protection) b.) Okhla Bird Sanctuary is approx. 8.78 km in SSE
Act, 1972? direction from the project site which is outside
the declared ESZ boundary of Okhla Bird
Sanctuary.
(c) The C.R.Z. Notification, 1990? c.) The C.R.Z. Notification, 1990 i s not applicable
as no coastal zone is coming within 10 km of the
project site.
22. Whether there is any Government Not applicable

order/policy relevant/relating to the
site?
23. Forests Land Involved (Hectares) No Forest Land is involved in the proposed Museum
Building Complex

24. Whether there is any litigation No litigation is pending against the project and/or
pending against the project and/or land in which the project is proposed.
land in which the project is proposed
to be setup?
(a) Name of the Court
(b) Case NO.
(c) Orders/ directions of the
Court, if any and its relevance with
the proposed project.
(II) Activity
1. Construction, operation or decommissioning of the Project involving actions,
which will cause physical changes in the locality (topography, land use, changes in water
bodies, etc.)
S. No. Information/Checklist Yes/No Details thereof (with approximate
confirmation quantities/rates, wherever possible)
with source of information data
1.1 Permanent or temporary change Yes The selected site falls under Public and
in land use, land cover or Semi Public land use as per the Master
topography including increase in plan of Delhi Development Authority
intensity of land use (with 2021 and will be developed as per the
respect to local land use plan) same.
The land will be used for the development
of cultural purpose and the land cover of
project site is a fallow land and depicts
plain topography (relative relief is less
than 5m) the construction activities of the
project are as per the Master plan of Delhi
Development Authority 2021 and will
help in increasing the aesthetic beauty.
During the construction phase, land cover

of the project site has been altered to some
extent, which is temporarily in nature.
As the project site is a vacant land, no
1.2 Clearance of existing land, clearance of existing land, vegetation and
No
vegetation and building? building will be done. No construction has
been started yet now.
The selected site is allotted for the cultural
1.3 purpose and it will be developed as per
Creation of new land uses? No
the Delhi Master plan 2021. There will be
no creation of new land uses.

1.4 Pre-construction investigations Yes The soil quality monitoring has been done
e.g. bore houses, soil testing? at the project site. The test report is
attached as Annexure-VIII.
1.5 Construction Work? Yes The construction in the proposed project
involves the development of museum
building having the built up a rea of
46,025.78 m2. Construction work is being
done as per Building Bye Laws of DDA
and the development of the project will be
as per master plan of Delhi Development
Authority 2021.
No Construction work has been started

yet.
1.6 Demolition works? No Not required
1.7 Temporary sites used for Yes Site office will be provided for the
construction works or housing of Construction Management team during
construction workers? construction phase. Temporary labour
sheds will be provided to construction
labour during construction phase. All the
construction activities including storage of
raw materials will be confined to the
project site only.
1.8 Above ground building, Yes Excavation will be carried out for
structures or earthwork including basement and foundation of building.
linear structures, cut and fill or During the construction phase, excavated
excavations earth from foundation of the project will
be reused for backfilling and landscaping
purposes. The excavated soil will be
properly stacked within the site under
tarpaulin cover.
1.9 Underground works including No As this is the Proposed Museum Building
mining or tunnelling? Complex, no mining or tunnelling would
be required.
1.10 Reclamation works? No No reclamation work required.
1.11 Dredging? No No dredging required.
1.12 Offshore structures? No No offshore structures required.
1.13 Production and manufacturing No As it is a Proposed Museum Building
processes? Complex, so these activities are not
associated with the project.

1.14 Facilities for storage of goods or Yes During construction stage, the following
materials? raw material handling methods will be
adopted:
• Cement will be separately stored
under cover in bales
• Sand & aggregates will be stacked
neatly under tarpaulin cover
• Bricks and steel will be laid in
open
• Finishing materials like tiles,
sanitary fixtures, etc will be stored
in closed rooms.
Material storage yard will be developed
for storage of construction materials.
1.15 Facilities for treatment or Yes 1.) Details regarding the Disposal and
disposal of solid waste or liquid treatment of Solid waste:
effluents?
i) Solid Waste generated during
construction phase: Details of
Construction waste is given below:
1. Soil, Sand and Gravel
2. Brick and Masonry
3. Concrete
4. Metal
5. Bitumen
6. Wood
7. Other (Glass, Plastic material, paper
etc.)
Reuse:
The construction waste will be used in
back filling, road making and pavement.
Metals, tin cans, glass are being sold to
local recyclers/kabadiwalas.
ii) Solid Waste generated during
operational phase:
Total quantity of the solid waste during
the operational phase will be around
1687.5 kg/day. Sludge generation will be
120.28 kg/day. The solid waste will
comprise of biodegradable fraction, non-
biodegradable fraction and inert fraction.
Disposal:

The biodegradable waste will be collected

in green coloured bins/containers and will
be segregated in collection chamber and
will be disposed to MSW site. Non bio
degradable waste will be collected into
blue bins/containers and will be
segregated in collection chambers and
sold to kabadiwala or govt. approved
agency or recycling industry. Inert waste
will be separately collected and stored in
black containers and will be handed over
to municipal authority.
Sludge will be used for horticulture
purposes.
Segregation, Collection at site and
disposal will be done as per Solid Waste
Management Rules, 2016.
2.)Details regarding the Disposal and

treatment of Liquid Effluent:
i) During the construction phase, approx.
2.4 KLD sewage is being generated and it
is being disposed through Soak pit / septic
tank.
ii) During the operational phase, sewage
generated will be 165 KLD and it will be
treated in the STP installed of 320 KLD
capacity of FBR technology. The treated
water will be recycled and reused for
flushing, DG Cooling and horticulture
purposes and the remaining excess treated
water, during monsoon season only, will
be discharged to sewer.
1.16 Facilities for long term housing There will be no facility for long term
No
of operational workers? housing for operational workers.
1.17 New road, rail or sea traffic Sectoral roads/existing roads are being
during construction or used in construction stage at the site for
operation? construction work and transport of
No construction materials.
During operational phase, traffic will
increase to some extent. But there will be
no rail or sea traffic.

1.18 New road, rail, air waterborne or Existing transportation routes will be used
other transport infrastructure for transportation:
including new or altered routes Transportation sources exiting near the
and stations, ports, airports etc? project site:-
Nearest railway station is New Delhi
Railway Station at an aerial distance of 4
km towards toward NNW.
No
Nearest Airport is Safdarjung Airport at
an aerial distance of 4.78 towards South -
West.
Bhairon Marg just adjacent to proposed

site towards NW.
1.19 Closure or diversion of existing No The project will not affecting the existing
transport routes or infrastructure traffic status during the construction phase
leading to changes in traffic and the same will continue during the
movements? operational phase.
1.20 New or diverted transmission No No new or diversion of transmission lines
lines or pipelines? or pipelines will be done.
1.21 Impoundment, damming, No No impoundment, damming, culverting,
culverting, realignment or other realignment or other changes to the
changes to the hydrology of hydrology of surface watercourses is
watercourses or aquifers? proposed.
1.22 Stream crossings? No No stream is crossing in the project site.
1.23 Abstraction or transfers of water No No ground water will be abstracted for
from ground or surface waters? any purpose during the construction phase
water supply will be met through private
water tankers and Water requirement
during the operational phase will be met
through Delhi Jal Board.
1.24 Changes in water bodies or the No The Yamuna river is located at the
land surface affecting drainage distance of 0.73 km towards East
or run-off? direction.
The sewage generated will be treated in
the STP and the treated water will be used
for flushing, DG cooling and landscaping.
Hence, it is expected that drainage or run
off will not be affected and change in
water body or the land surface will not
occur.
1.25 Transport of Personnel or Yes There will be transport of construction
materials for construction, materials by trucks or trolleys etc.
operation or decommissioning? Precautions will be taken to reduce the

impact of the vehicular movement by
trying to avoid the vehicular trips during
peak hours.
1.26 Long-term dismantling or No Not Applicable
decommissioning or restoration
works?
1.27 Ongoing activity during No Not Applicable
decommissioning which could
have an impact on the
environment?
1.28 Influx of people to an area in Yes Construction phase:
either temporarily or Workers from nearby area will be hired in
permanently? the construction phase. (Temporarily).
Operation Phase:
Staff and visitors within museum
complex.
1.29 Introduction of alien species? No Native/Local species will be planted.
1.30 Loss of native species or genetic

No No
diversity?
1.31 Any other actions? No No
2. Use of Natural resources for construction or operation of the Project (such as

land, water, materials or energy, especially any resources which are non-renewable or
in short supply):
S. No. Information/ Checklist Yes/No Details thereof (with approximate

confirmation quantities /rates, wherever possible
with source of information data)
2.1. Land especially No The land will be used for the cultural
undeveloped/agricultural purpose as per the master plan of DDA
2021 and will be developed as per the
same.
2.2. Water (expected source & Yes Total water requirement of the proposed
competing users) Unit: KLD project will be approximately 370 KLD.
Fresh Water Supply: 138 KLD
Flushing: 61 KLD
Horticulture: 35 KLD
DG Cooling: 18 KLD
HVAC: 114 KLD
Fire fighting: 4 KLD
Source of water would be municipal water

supply (Delhi Jal Board).
2.3. Minerals (MT) No Not Applicable
2.4. Construction material – stone, Yes List of building materials being used at
aggregates, sand/soil ( expected site:
source – MT) 1. Coarse sand
2. Fine sand
3. Stone aggregate
4. Stone for masonry work
5. Cement
6. Reinforcement steel
7. Plywood & steel shuttering
8. Pipe scaffolding (cup lock
system)
9. Bricks
10. Tiles
11. P.P.V.C. conduit
12. MCBs/DBs
13. PVC overhead water tanks
14. Pave tiles
15. GI pipe
16. Wastewater lines
17. S.W. sewer line up t o main
sewer
18. PVC rain water down take
19. Stainless steel sink in kitchen
2.5. Forests and timber (source – Yes Minimum wood will be used in the
MT) project, mainly would be used for doors in
the proposed project. Aluminium frames
will be used at most of the places.
2.6. Energy including electricity and Yes 1. Electricity Source:
fuels (source, competing users) Power consumption during the operational
Unit: fuel (MT), energy (MW) phase will be 2430 KW and will be
supplied by BSES Rajdhani Power
Limited.
2. Backup power source:
In case of power failure, 3 DG sets of total
capacity of 3030 kVA (3 x 1010) will be
provided as power back-up for the
essential load.
2.1. Any other natural resources (use No Not Applicable
appropriate standard units)

3. Use, storage, transport, handling or production of substances or materials, which

could be harmful to human health or the environment or raise concerns about actual or
perceived risks to human health.
S. Information/Checklist Yes/No Details there of (with approximate
No. Confirmation quantities/rates, wherever possible)
3.1 Use of substances or materials, No There will be no us e of the substances or

which are hazardous (as per material which are hazardous, as per
MSIHC rules) to human health or Manufacture Storage and Import of
the environment (flora, fauna, and Hazardous Chemicals Rules, 1989 and its
water supplies) amendments 2000.
3.2 Changes in occurrence of disease of No The solid waste generated both during
disease or affect disease vectors construction phase is being properly
(e.g. insect or water borne diseases) managed and disposed off during the
construction phase and the same will be
followed during the operation phase. The
sewage generated from the project will be
treated in a STP. The cleanliness of the
project shall be maintained. Hence, it is
expected that there shall be reduction in
vectors as well as vector borne diseases.
3.3 Affect the welfare of people e.g. by Yes Due to the proposed project Socio-
changing living conditions? Economic condition due to increased
employment opportunities provided by the
project and aesthetic beauty of the area
will improve due to the development of
the landscape. The project shall not have
any adverse effect on the living condition
of the people.
3.4 Vulnerable groups of people who No The project shall not affect any vulnerable
could be affected by the project e.g. groups of people in the vicinity.
hospital patients, children, the
elderly etc.,
3.5 Any other causes No Not Applicable
4. Production of solid wastes during construction or operation or operation or

decommissioning (MT/month)
S. No. Information/Checklist Yes/No Details thereof (With approximate


4.1 Spoil, overburden or mine wastes No As this project is the proposed Museum
Building Complex, so no m ine spoil and
overburden waste will be generated
4.2 Municipal wastes (domestic and or Yes Total municipal waste generated from the
commercial wastes) project will be 1687.5 kg/day.
4.3 Hazardous wastes (as per Yes Used oil/spent oil from the DG Sets as per
Hazardous Waste Management the Category 5.1, of Schedule-1 of the
Rules) Hazardous and Other Wastes
(Management and Transboundary
Movement) Rules, 2016.
Suitable management practice will be

adopted for the same. It will be stored in
HDPE drums and kept in covered rooms,
under lock and key and will be sold to
SPCB authorized vendor’s only.
Specialized care will be taken to prevent
leaks and/or spills.
4.4 Other industrial process wastes No Not Applicable
4.5 Surplus product No Not Applicable
4.6 Sewage sludge or other sludge Yes The sludge (on wet basis) generated from
from effluent treatment STP is 120.28 kg/day and it will be dried
and used for horticulture purposes.
4.7 Construction or demolition wastes Yes Details of Construction waste is given
below:
1. Soil, Sand and Gravel
2.Brick and Masonry
3. Concrete
4. Metal
5. Bitumen
6.Wood
7. Other (Glass, Plastic material, paper
etc.)
Construction waste shall be used for back
filling, road making and pavements.
There are two structures on the site which

will be demolished and the demolition
waste will be used for back filling
purposes.
4.8 Redundant machinery or equipment No Not Applicable
4.9 Contaminated soils or other No Not Applicable
materials

4.10 Agricultural wastes No Negligible waste will be generated from

landscape, which will be the bio-
degradable waste.
4.11 Other solid wastes No Not Applicable
5. Release of pollutant or any hazardous, toxic or noxious substances to air (kg/hr)

S. Information/Checklist Yes/No Details thereof (with approximate
No. confirmation quantities/rates, wherever possible)
5.1 Emissions from combustion of Yes The operation of proposed project does
fossil fuels from stationary or not envisage any major air pollutant
mobile sources generating sources.
5.2 Emissions from production No Not applicable as it is Proposed Museum
processes Building Complex.
5.3 Emissions from materials handling Yes Fugitive emissions will be envisaged only
including storage or transport from material handling and transporting
areas, loading/unloading the construction
material, transportation and earthwork
(levelling etc.) during the construction
period. Regular sprinkling of water in the
construction area will be done.
5.4 Emissions from construction Yes As most of the construction equipment
activities including construction will be mobile, the emissions will be
materials, sewage and waste fugitive in nature. The dust generated will
be also fugitive in nature, which will be
being controlled by suitable mitigation
measures like sprinkling of water.
Sewage generated from labours shed and

it will be disposed off by Soak pit /septic
tank.
The impacts are localized in nature and

the areas outside the project boundary will
not having any adverse impact with
respect to ambient air quality.
5.5 Dust of odours from handling of Yes Dust will be generated during the
materials including construction construction phase, water sprinkling and
materials, sewage and waste tarpaulin will be provided over stored raw
material to reduce dust emission.
5.6 Emissions from incineration of No Not Applicable
waste
5.7 Emissions from burning of waste in No Burning of waste will not be done and the

open air (e.g. slash materials, waste generated shall be managed as per
construction debris) the Solid Waste Management Rules, 2016.
Construction debris will be used in
internal road construction.
5.8 Emissions from any other sources No Not Applicable
6. Generation of Noise and Vibration, and Emissions of Light and Heat:

S. No Information/Checklist Yes/No Details thereof (with approximate
6.1 From operation of equipment e.g. Yes During construction the machinery used
engines, ventilation plant, crushers for construction will be of highest standard
of reputed make and will adhering to
international standard. These standards
itself take care of noise pollution control/
vibration control and air emission control.
Hence insignificant impacts due to
construction machinery will be envisaged.
Apart for this the construction activities
will be restricted to day time only.
Moderate noise being generated from
Construction Machineries such as
Concrete mixer with hopper,
JCB/Pockline, Road roller. To avoid this,
ear muffs will be provided to the
construction worker.
6.2 From industrial or similar No Not Applicable
processes
6.3 From construction or demolition Yes Moderate noise during construction
6.4 From blasting or piling No No blasting or mechanized piling will be
done in the construction phase.
6.5 From construction or operational Yes Noise generated due to traffic movement
traffic will be further minimized by plantation on
the sides of internal roads, on t he open
spaces inside the and around the
periphery.
Informatory signboards shall be provided
to encourage vehicle owners to maintain
their vehicle, not to blow horns.
6.6 From lighting or cooling systems No Not Applicable
6.7 From Any other sources No Not Applicable
7. Risks of contamination of land or water from releases of pollutants into the ground or into
sewers, surface waters, groundwater, coastal waters or the sea:

with source of information data.
7.1 From handling, storage, use or Yes The used oil from DG sets will be
spillage of hazardous materials carefully stored in HDPE drums at isolated
storage, and periodically sold to authorized
recyclers. All precautions will be taken to
avoid spillage from storage as per The
Hazardous and Other Wastes
(Management and Transboundary
Movement) Rules, 2016
7.2 From discharge of sewage or other No Treated sewage from STP will be reused
effluents to water or the land for flushing, DG cooling and landscaping
(expected mode and place of and excess treated water, during monsoon
discharge) season only, will be discharged to sewer.
7.3 By deposition of pollutants No Not Applicable
emitted to air into the land or into
water
7.4 From any other sources No Not Applicable
7.5 Is there a risk of long term build No There is no such risk.

up of pollutants in the environment
form these sources?
8. Risk of accidents during construction or operation of the Project, which could affect
human health or the environment
8.1 From explosions, spillages, fires etc No This is basically a construction project
from storage, ha ndling, use or and does not involve major hazardous
production of hazardous substances construction activity. Hence, chances of
explosions, spillages, fires are minimal.
During construction, all the labourers

will be provided with suitable personal
protective equipment (PPE) as required
under the health and safety norms.
Training and awareness about the safety
norms will be provided to all supervisors
and labourers involved in construction
activity.
An agreement will be signed with the

contractor, which will clearly deal with

the safety aspects during construction.
No major hazardous waste shall be stored
within the project site. No chemical
industry or process activity will involve
in this project, hence no chemical hazard
and accidents due to the envisaged.
8.2 From any other causes No Not Applicable.
8.3 Could the project be affected by No The project falls under seismic active
natural disasters causing Zone IV indicating High damage risk
environmental damage (e.g. floods, zone, according to the Indian Standard
Seismic Zoning Map. The buildings will
earthquakes, landslides, cloudburst
be designed as earthquake resistant and
etc)? comply with the required IS
specifications.
There are no c hances of floods and
landslide.
9. Factors which should be considered (such as consequential development) which could

lead to environmental effects or the potential for cumulative impacts with other existing or
planned activities in the locality

9.1 Lead to development of Yes Appropriate infrastructure like roads,
supporting facilities, ancillary power supply, waste management
development or development and waste water treatment will be
stimulated by the project which developed within the project site.
could have impact on t he Development of the area will be as
environment e.g.: per the proposed master plan of DDA
• Supporting infrastructure 2021. There will be a cumulative
(roads, power supply, waste or positive impact on the environment in
waste water treatment, etc.) terms of better infrastructure.
• Housing development No Not applicable

• Extractive industries No Not Applicable
• Supply industries No Not applicable
• Other No Not applicable
9.2 Lead to after-use of the site, No Not Applicable
which could have an impact on
the environment
9.3 Set a precedent for later Yes Infrastructure development of area.
development Socio Economic condition will
improve.
9.4 Have cumulative effects due to No As it is planned development by the

proximity to other existing or authorities and as per the master plan,
planned projects with similar hence no adverse impacts are
effects
envisaged.
(III) Environment Sensitivity

Aerial distance (within
S. No. Area Name/ Identity 15km) Proposed project
location boundary
1. Areas protected under • Jahanpanah City Forest Approx. 9.07 Km, S
international conventions, • Hauz Khas Forest Approx. 7.08 km, SSW
national or local legislation for • Central Ridge Reserve Approx. 6.55 km , NW
their ecological, landscape, Forest
• Nothern ridge Forest Approx. 10.55 km, N
cultural or other related value Approx. 15.07 km , SW
• Rajokri PF
2. Areas which are important or • Jahanpanah City Forest Approx. 9.07 Km, S
sensitive for ecological reasons • Hauz Khas Forest Approx. 7.08 km, SSW
–Wetlands, watercourses or • Central Ridge Reserve Approx. 6.55 km , NW
other water bodies, coastal Forest
• Nothern ridge Forest Approx. 10.55 km, N
zone, biospheres, mountains, Approx. 15.07 km , SW
forests • Rajokri PF
• Yamuna River Approx. 0.73 km, East
3. Area used by protected,
important or sensitive species of
flora or fauna for breeding, • Okhla Bird Sanctuary Approx. 8.78 Km , SSE
• Asola Wild life sanctuary Approx. 16.27 Km, S
nesting, foraging, resting, over
wintering, migration
4. Inland, coastal, marine or • Yamuna River Approx. 0.73 km, East
underground waters
5. State, National boundaries • Delhi -UP state border Approx.6 km in SE
• Delhi-Haryana border Approx.13 km, S
6. Routers or facilities used by the • Bhairon Marg Adjacent to site, NW
public for access to recreation • Mahatma Gandhi Marg Approx. 0.35 Km ,E
or other tourist, pilgrim areas • GT Road Approx.0.36 Km, E
• Mathura road Approx. 0.55 Km , W
• AH-2 Approx. 344.31 m, E
7. Defence installations None ---
8. Densely populated or built-up • Kaka Nagar Approx. 1 Km , SE
area • Bapa Nagar Approx.81 Km, SE
• Sanjay Amar Colony Approx. 1.41 Km , N
• Pandara Flats Approx. 1.9 Km , SSE
• Nizamudin Approx. 1.9 km, S

9. Areas occupied by sensitive List of Schools:

man-made land uses (hospitals, • Guru Harkrishan Public Approx. 1.09 Km, NE
schools, places of worship, School, India Gate
community facilities) • Mater Dei school, Tilak Approx. 1.04 km ,NE
lane
• Indian Society of Approx. 1.26 km , NNE
International Law
• Lady Irwin College Approx. 2 Km , NNE
List of Hospitals:
• Sanjeevan hospital Approx. 3.36 km, N
• Guru Nayak Eye Centre Approx. 3.26 km, NNW
List of Temples:
• Sri Kilkari Baba Nath ji Approx. 68 meter, W
Pando Kaalin Mandir
• Chandi Sheetla Mnadir Adjacent to site , S
• Shri baba Dudhiya Bhairo Adjacent to site, SW
Nath ji Pandav Kallin
• Matka Pir masjid Approx.0.56 Km, NW
10. Areas containing important, • Yamuna River Approx. 0.73 km, East
high quality or scarce resources • MCD Drain Adjacent, North
(ground water resources,
surface resources, forestry,
agriculture, fisheries, tourism,
minerals)
11. Areas already subjected to Okhla Industrial Area Approx. 9.07 Km, South
pollution or environmental
damage. (those where existing
legal environmental standards
are exceeded)
12. Areas susceptible to natural Yes Area is susceptible to
hazard which could cause the Earthquake. Project area
project to present environmental falls in Zone-IV as High
problems (earthquakes, Damage Risk Zone.
subsidence, landslides, erosion,
flooding or extreme or adverse
climatic conditions)
(IV) Proposed Terms of Reference for EIA studies – Not Applicable

APPENDIX II
(See paragraph 6)
FORM-1 A (only for construction projects listed under item 8 of the Schedule)
CHECK LIST OF ENVIRONMENTAL IMPACTS
(Project proponents are required to provide full information and wherever necessary
attach explanatory notes with the Form and submit along with proposed environmental
management plan & monitoring program)
1. LAND ENVIRONMENT
Figure-1: Perspective View of Project
1.1 Will the existing land use get significantly altered from the project that is not consistent
with the surroundings? (Proposed land use must conform to the approved Master Plan /
Development Plan of the area. Change of land use if any and the statutory approval from
the competent authority to be submitted). Attach Maps of (i) site location, (ii) surrounding
features of the proposed site (within 500meters) and (iii) the site (indicating levels &
contours) to appropriate scales. If not available attach only conceptual plans.

Landuse Pattern: National Museum Of Natural History is going to develop a Proposed
Museum Building Complex on the total land area measuring 26,299 m2.The built up a rea is
46,025.78 m2. The development will be done is in accordance with Municipal Corporation of
Delhi and will be developed as per the master plan of Delhi.
Site Location: National Museum of Natural History has proposed Museum building complex at
Bhairon Marg, behind Purana Quila, New Delhi.
Geographically, the proposed project site is located at:
 Latitude 28° 36' 39.57"N

 Longitude 77° 14' 48.46"E
Master plan showing the project site is given in Figure-2.

Surrounding Features: The proposed project site is connected to Noida, and other NCR
regions. It is surrounded by Kaka Nagar, Bapa nagar, Sanjay amar colony, Pandara Flats ,
Nizamudin.etc. Residential areas within 2km radius area of the proposed project site.
A Google Map showing surrounding area of project within 500 m is shown in Figure-3.
The topographical survey plan is attached as Annexure-VII.

Proposed Museum building complex at Bhairon Marg, behind Purana Quila, New Delhi by National Museum Of Natural History
Project Site
Figure-2: Master plan showing the project site

Figure-3: Google Map of the area showing surroundings within 500m radius

1.2 List out all the major project requirements in terms of the land area, built up area, water
consumption, power requirement, connectivity, community facilities, parking needs etc.
National Museum of Natural History has proposed Museum building complex at Bhairon Marg,
behind Purana Quila, New Delhi.
The development will be done is in accordance with Municipal Corporation of Delhi and will be
developed as per the master plan of Delhi.
Land Area: The proposed Project is being developed on the total plot area of 26,299 m2.
Built up Area: The built up a rea of the proposed project is 46,025.78 m2 which includes the
FAR and Basement.
Water Consumption: During the construction phase, water requirement will be met through the
private water tanker. It is estimated that water demand during the construction phase may vary
from 24 KLD.
The total water requirement for the proposed project has been estimated to be 370 KLD. This
includes domestic water requirement, flushing, landscaping, DG cooling and make water
requirement for swimming pool. The total fresh water requirement is 138 KLD which includes
Domestic water requirement & make water requirement for swimming pool. T he water
requirement for Flushing, DG cooling and landscaping will be met through treated water from
STP.
Power Requirement: The total electrical load demand has been estimated to be 2,430 KW. The
source of power will be supplied by BSES Rajdhani Power Limited.
Connectivity: Nearest railway station is New Delhi Railway Station at an aerial distance of 4 km
towards NNW.
Nearest Airport is Safdargunj Airport at an aerial distance of 4.78 km towards South West.
Community Facilities: The project site is surrounded by many schools and hospitals such as:
Schools:
Guru Harkrishan Public School, India Gate Approx. 1.09 Km, NW
Mater Dei school, Tilak lane Approx. 1.04 km , NW
Indian Society of International Law Approx. 1.26 km , NNW

Lady Irwin College Approx. 2 Km , NNW
Parking Requirements: 635 ECS is provided in the basement, stilt and on surface.
1.3 What are the likely impacts of the proposed activity on the existing facilities adjacent to the
proposed site? (Such as open spaces, community facilities, details of the existing land use,
disturbance to the local ecology).
The proposed development shall be carried out as per the Delhi building by-laws and as per
planned land use, hence no negative impact is envisaged due to proposed development. Further,
the construction as well as operation stage of the project will generate direct and indirect
employment opportunities for a large section of society. The employment will have positive
impact thereby improving the quality of life.
As the project site for construction consists of herbs and shrubs it will require clearance of land
for construction purposes. The green area will be developed as shelter belt, along with avenue
plantation on both sides of road, lawns area including herbs and shrubs. The indigenous/local
plants will be planted, which will increase the aesthetic value of the area. Hence, there will be no
disturbance to the local ecology of the area.
1.4 Will there be any significant land disturbance resulting in erosion, subsidence &
instability? (Details of soil type, slope analysis, vulnerability to subsidence, seismicity etc
may be given).
Delhi geography divides the state into three parts- the Delhi ridge, the Yamuna flood plain and
the plains. The Yamuna river plains are very fertile as they are flooded by the river and rich in
alluvial soil. The Delhi ridge is the most important characteristic of the state and is a part of the
Aravali range that passes through Delhi.
Soil Type: The soil type is derivative of Yamuna flood plain alluvium due to which there is
progressive clayey material at the top of the soil horizon while the sand and silt portions increase
progressively downwards.
The Soil sample was collected from the project site and the results are given in Table- 1 below:-

Table-1: Result of Soil Quality
Sr.No. Test Parameters Unit Results Test Method

1 pH(1:5) - 8.56 IS 2720 (P-26)
2 Conductivity(1:5) µmhos/cm 216 USDA Method
3 Colour - Brown USDA Method
4 Texture
Silt % 13
USDA Method
Clay % 28
sand % 59
5 Sodium absorption ratio - 0.34 USDA Method
6 Cation exchange capacity Meq/100gm 75.3 IS 2720 (P-24)
7 Porosity % 61 USDA Method
8 Water Holding Capacity % 39.9 USDA Method
9 Bulk Density gm/cc 1.17 USDA Method
10 Chloride as Cl mg/kg 175 USDA Method
11 Calcium as Ca mg/kg 1.15 USDA Method
12 Sodium as Na mg/kg 155 USDA Method
13 Potassium as K mg/kg 50 USDA Method
14 Magnesium as Mg mg/kg 3500 USDA Method
15 Organic matter % 0.79 IS 2720 (P-22)
16 Available Nitrogen mg/kg 565 USDA Method
17 Phosphorous mg/kg 50 USDA Method
18 Zinc as Zn mg/kg <2.0 USDA Method
19 Manganese as Mn mg/kg <2.0 USDA Method
20 Copper as Cu mg/kg <2.0 USDA Method
Reference Methods: Soil Chemical analysis by Jackson, M.L. 1967.
The Monitoring reports are attached as Annexure-VIII.
The proposed activity will not affect any land disturbance resulting in erosion, subsidence and
instability. The area is not susceptible to erosion.
Slope Analysis:
The topography of the City is almost plain.

(Source: CGWB 2008-2009)

The project area possesses fairly plain terrain with negligible drainage slope of the project site.
Subsidence/Erosion:
Proper greening and paving of site area will not cause any soil subsidence problem.
Seismicity:
 The whole country has been divided into 5 S eismic zones as per maximum intensity of
‘Modified Mercalli Scale’ (MMS). The project site lies in Seismic Zone IV, called as ‘High
Damage Risk Zone’.(Reference: India Earthquake Zone map)
Seismic zone classification of India is shown in Figure-4.
Project site
.
Source: Indian Meteorological Department
Figure-4: Map showing the Seismic Zone classification

1.5 Will the proposal involve alteration of natural drainage systems? (Give details on a contour
map showing the natural drainage near the proposed project site).
River Yamuna is coming within 0.73 km towards East and MCD Drain is adjacent to the
proposed site towards North. No natural drainage lies in the vicinity of the Proposed Project Site.
Drainage map of the proposed project site is given in the Figure-5 below:

Figure-5: Drainage Map of 10 km radius of the Project Site

1.6 What are the quantities of earthwork involved in the construction activity-cutting, filling,
reclamation etc. (Give details of the quantities of earthwork involved, transport of fill
materials from outside the site etc?)
During Construction phase, excavation will be carried out to provide foundations and for
establishing the pillar. This excavated soil will be properly stacked within the site under tarpaulin
cover. The filling works will be done by the excavated material and no extra material will be
used. All the topsoil excavated during construction activities is being stored for use in
horticulture/landscape development within the project site.
1.7 Give details regarding water supply, waste handling etc. during the construction
period.
Water Supply:
Water required during the construction period will be supplied through private water tanker.
It is estimated that water demand during the construction phase may vary from 24 KLD.
Water will be used in the construction activity for cement mixing, sprinkling, dust
suppression and domestic purposes of the construction workers.
Waste Generation/Handling:
Sewage: The existing sewerage collection facilities comprising of toilets and urinals shall be
used by the construction workers and staff involved. No additional sewage shall be generated
which has to be separately disposed off.
Construction waste: No demolition waste will be generated as the site was a vacant plot
when the excavation began. The solid waste generated during the construction phase like
metal cutting. Debris, plastic material and wooden log etc. is being collected and stored in a
separate covered area so as to prevent damage to property and personnel working at the
project site. Further, most of the construction debris is being used for filling activities and the
rest is being disposed off through authorized recyclers. The excavated soil will be used on
site for the development of green belt and leveling of the plot.
The waste generated during the construction activities is limited to project site only and
during construction phase only. These will be reused for backfilling and road development
after manual segregation. This waste shall be utilized for construction of roads.
Major types of construction wastes are expected from the proposed Project: -
 Clean Fills:
Clean fill is uncontaminated soil, rock, sand, gravel, concrete, asphaltic concrete, cinder
blocks brick, minimal amounts of wood and metal and inert (non-reactive) solids for fill,
reclamation or other beneficial use. Minimal means the smallest amount possible.

 Recovered Materials
Recovered Materials are those removed for reuse (lumber, doors, windows, ceramic tile
and glass) and those removed to be recycled into new products. Potentially recyclable
construction and demolition wastes will include scrap metals, asphalt shingles, sheet
rock, lumber, glass and electrical wire.
 Regulated construction and demolition waste

Regulated construction and demolition wastes are those not classified as clean fill and not
being reused or recycled. Regulated non-hazardous construction and demolition wastes
will be disposed off at a permitted landfill or transfer station.
Scrap metal painted with heavy metals will be sent to a salvage yard for recycling.
Conclusively, it can be stated that impacts may be confined to small area (mainly to project
site) and for short duration. Construction waste will be reused; disposal of non-reusable
waste will be done through authorized vendors/recyclables.
Solid Waste during Construction Phase
Table-2 gives an estimate of the average composition of waste generated from the onsite
construction activities whereas Table-3 lists of the various hazardous wastes expected to be
generated from the project during construction.
Table-2: Waste Composition - During Construction Phase

S. No. Constituents Percentage Composition
1 Soil, Sand and Gravel 34.99
2 Brick and Masonry 29.95
3 Concrete 24.98
4 Metal 4.97
5 Bitumen 2.04
6 Wood 2.04
7 Other 1.02
Total 100
Source: TIFAC Report “Utilization of Waste from Construction Industry,” 2001

Table-3: Types of hazardous waste to be generated during construction

S.No. Hazardous Waste
Construction phase
1. Used Oil from DG Sets
2. Centering Oil, formwork oil
3. E-waste- Circuit boards, CRTs, Electronic parts, solder dross, weld waste
4. Paints, pigments, dyes and primers
Fuels and heating oils and other volatile/ flammable liquids such as coolants, grease
5.
etc.
6. Tar and tar products
7. Lead containing products
8. Product packaging (cement bags, cartons, containers, plastic covers etc.
Fluorescent lamps intact and crushed, halogen lamps, arc lamps, UV lamps, high
9.
pressure sodium lamps, neon lamps, incandescent lamps.
Mercury containing lamps and tubes, mercury vapor lamps, Mercury containing
10. devices- mercury switches, relays, regulators, thermostats, manometers and debris
containing mercury.

Solid Waste
Construction
Waste Food Waste Hazardous waste
As per Solid
Empty Waste As per Hazardous
Cement Excavated Soil Management and Other Wastes
Construction waste, (Management and
Broken Bricks, Bags Rules, 2016
Transboundary
Waste Plaster Movement) Rules,
2016
Sold to agency for Top soil conserved

Used in re-filling,
recycling/used for for landscaping,
raising site level
road construction balance used in re-
filling
Figure-6: Solid Waste Management during Construction Phase
1.8 Will the low lying areas & wetlands get altered? (Provide details of how low lying and
wetlands are getting modified from the proposed activity).
Sewage generated will be treated in the onsite STP of Fluidised Bed Reactor Technology of 320
KLD. Hence, no low lying areas will get altered.
1.9 Whether construction debris & waste during construction cause health hazard? (Give
quantities of various types of wastes generated during construction including the
construction labor and the means of disposal).
 No significant health hazard is associated with the proposed construction.
 During construction period, source of fugitive dust generation is from material handling and
vehicular movement. Impact due to fugitive dust emission shall be negligible as water
sprinklers are being used to suppress fugitive dust emission as and when generate. However,
the impacts are confined to laborers/workers particularly with regard to occupational

exposure. Proper Personal Protective Equipments have been provided to the workers working
in the potential areas (e.g. masks, ear plugs etc.).
 Careful design, planning and good site management has minimized waste of materials such
as concrete, mortars and cement grouts. Construction wastes are being segregated as much as
possible at site itself to increase the feasibility of recycling concrete and masonry as filling
material and steel pieces as saleable scrap. Litter disposal and collection points have been
established around the work sites. Empty packaging materials, drums, glass, tin, paper,
plastic, pet bottles, wood, and other packaging materials, etc are being disposed through
recyclers. The construction spoils are being temporarily stored at designated dumpsite
located inside the site premises. Later on these wastes will be used for land filling / leveling
work within the site premises. An estimate of the average composition of waste generated
from the onsite construction activities given in Table-2.
2. WATER ENVIRONMENT
2.1. Give the total quantity of water requirement for the proposed project with the breakup of
requirements for various uses. How will the water requirement met? State the sources &
quantities and furnish a water balance statement.
Water Requirement:
During Construction Phase:
During construction phase, water will be sourced primarily through tankers arranged by the
contractor. It is estimated that water demand during the construction phase may vary from 24
KLD which will be used in domestic as well as construction purpose.
Details of 24KLD water used During Construction:

Supervisory & Construction Labour= 550 persons @45 LPCD =12.22 KLD
(Drinking = 11.25 KLD and Other=22.5 KLD)
Curing & Mixing of Mortar & Cement = Approx. 8KLD
Dust control = Approx. 3 KLD
During Operation Phase:

Water requirement during the operational phase will be met through Delhi Jal Board.
includes domestic water requirement, flushing, landscaping, DG cooling and make water
requirement for swimming pool. The total fresh water requirement is 138 KLD which includes
Domestic water requirement & make water requirement for swimming pool. T he water
requirement for Flushing, DG cooling and landscaping will be met through treated water from
STP.
Table-4: Detail of water requirement for the proposed project
Unit water
Area in Total
water requiremen Flushing Total
Sq.m. / water
S. No. Description consumpt t for water Wastewat
Populati required
ion domestic (kld) er (kld)
on (kld)
(litres) use (kld)
Visitors population
+Auditorium population +
Imax Theatre + 4830 15 72.45 43.470 28.980 63.756
Convention Centre
1 Population
Staff population +
Dormitories population + 1858 45 83.61 55.740 27.870 72.462
2 Guest room
Population of rental
282 45 12.69 8.460 4.230 10.998
3 offices and other offices
Kitchen & Pantry.
Restaurant Kitchen, Food ….. 30 30.000 ….. 18.000
4 Court
7003.91 5 litr per
35.02 …. ….. ….
5 Horticulture Sqm sqm
1
3030.00 ltr/KVA/h 18.18 ….. ….. ….
6 DG Sets r
11.5
412.00 113.71 ….. ….. ….
7 HVAC lt./ton/hr.
1% of
total water
requireme
8 Fire fighting nt 3.66 …. …. ….
TOTAL 369.32 137.670 61.080 165.216
Say 370 Say 138 Say 61 Say 165
Water balance diagram in Non-Monsoon season is given in Figure-7 and monsoon season is
given in Figure-8.
Total waste water generated is 165 KLD, which will be treated in the STP of capacity higher
than the waste water generated i.e. 320 KLD. The treated water available is 132 KLD (@ of
80%) and it will be recycled and re-used for flushing, DG Cooling and landscaping. During the
non-monsoon season, treated water will be used in Flushing, DG Cooling & landscaping and

during the monsoon season, as there will be less requirement of water for landscaping, and the
excess treated water i.e. 20 KLD will be discharged to sewer during monsoon season.

One time water

Requirtment=
370
Firefighting Fresh water Flushing water 61

Requirtment (one Requirtment= Requirtment= 61
time) = 4 138 35
Landscaping = 35
Domestic Water Kitchen Water 18 DG sets cooling =

requirement = 108 requirement = 30 18
96
Domestic Wasteweter Kitchen Wasteweter Flushing Wasteweter HVAC = 114

generation @ 80 % = 86 generation @ 60 % = 18 generation @ 100 % = 61
18
All Figures in KLD
Total Wastewater generation
= 86+18+61= 165
Total water Requirtment

One Time Requirement
Fresh Water Requirement
Fresh water Requirement STP capacity 20% more than
Wastewater Generation total wastewater generation = Recycled water
Treated Water
Wastewater Generated 200 @80% = 132
but we provided approx 320
Recycled Water Recirculated condensate KLD STP at site for safer side
Water
Figure-7: Water Balance Diagram for Non-Monsoon Season

One time water

Requirtment=
370

time) = 4 138 15
Landscaping = 15

96

All Figures in KLD

18

= 86+18+61= 165
Fresh Water Requirement Discharge to sewer

Wastewater Generation = 20
Treated Water STP capacity 20% more than

total wastewater generation = Recycled water
Recirculated condensate 200 @80% = 132
Water but we provided approx 320
KLD STP at site for safer side
Figure-8: Water Balance Diagram for Monsoon Season

2.2. What is the capacity (dependable flow or yield) of the proposed source of water?
Water requirement of construction phase will be met from Private water supplier/treated water
from CSTP. While during operation phase water requirement will be met through Municipal
supply.
2.3. What is the quality of water required, in case, the supply is not from a municipal source?
(Provide physical, chemical, biological characteristics with class of water quality)
Water requirement of construction phase will be met from Private water supplier/treated water
from CSTP. During post construction water demand will be met form Delhi Jal Board. Ground
water, if required abstraction will be done only after getting NOC from CGWA. During
operation phase the supplied drinking water to each dwelling unit will be as per Bureau of Indian
Standards (BIS) and IS: 10500-2012.
2.4. How much of the water requirement can be met from the recycling of treated wastewater?
(Give the details of quantities, sources and usage)
About 132 KLD of total water requirement will be fulfilled from recycled water after treatment
from STP and rest will be met from Delhi Jal Board.
2.5. Will there be diversion of water from other users? (Please assess the impacts of the project
on other existing uses and quantities of consumption).
There will not be such diversion of water from other users as the water demand during
construction phase will be met from Private water tanker. In operational phase water demand
will be met form Delhi Jal Board. Ground water abstraction, if required will be done only after
getting NOC from CGWA. Hence, no impact on others user observed.
2.6. What is the incremental pollution load from wastewater generated from the proposed
activity? (Give details of the quantities and composition of wastewater generated from the
proposed activity).
During the operational phase, 165 KLD waste water will be generated which will be treated in
the proposed sewage treatment Plant.
The waste water generated will be treated in the Sewage Treatment Plan, and the capacity of
Sewage Treatment Plant (STP) will be higher of waste water generated i.e. 320 K LD. The
proposed STP is based on FBR (Fluidised Bed Reactor). The treated waste water will be used for
flushing and horticulture, DG Cooling purposes.
The waste water generation is given in Table-5. Table-6 shows expected characteristic of
untreated and treated wastewater.

Table-5: Details of Wastewater Generation

Details Water (KLD)
Water requirement for domestic purpose 108
Wastewater to be generated from domestic use (@ 80% of domestic 86
water requirement)
Water Requirement for kitchen purpose 30
Wastewater to be generated from kitchen use (@60%) 18

Water requirement for Flushing Purpose 61
Wastewater to be generated from Flushing (@ 100% of flushing 61
requirement)
Total Wastewater generated 86+18+61 = 165 KLD
Table-6: Characteristic of untreated and treated sewage

S.No Parameter Unit Inlet Outlet
1. pH - 6.5 – 8.5 7.0-7.5
2. Suspended Solids mg/l 200-300 <10
3. BOD (3 days at 27 ºC) mg/l 250-300 <10
4. COD mg/l 350 – 450 <75
5. Oil & Grease mg/l 10-20 <10
The waste water generation will be about 165 KLD. After treatment in STP, about 132 KLD will
be available for reuse, which will be used for flushing, horticulture, DG Cooling and all excess
treated water will be discharged to sewer.
2.7. Give details of the water requirements met from water harvesting? Furnish details of the
facilities created.
(i) Rainwater Collection Potential for Reuse or Recharging
 Rainwater harvesting is the activity of direct collection of rainwater. Collected Rainwater
will be stored for direct use, for harvesting or for recharging the groundwater. Rain Water
Harvesting is the technique through which rain water is captured from the roof and paved
surfaces and stored in sub-surface ground water reservoir by adopting artificial recharge
techniques. The run off calculations for Rain Water Harvesting are shown in Table-7 and for
pits in Table-8.

 As in delhi, the ground water table is very high i.e. 2.5 m below the existing ground level. So,
RWH pits are not feasible.
 Therefore, we are proposing 5 rain water harvesting structure.
Table-7 Runoff Calculation of the Area
Intensity of Intensity of Runoff

S. Type of Catchment Runoff Runoff
Rainfall Rainfall (In 15
No. Surface Area (m2) Coefficient (m3 /hr)
(mm/hr) (m/hr) minutes)
1. Roof Area 9202.7 0.8 11 0.011 80.98 20.24
2. Green Area 7003.91 0.2 11 0.011 15.41 3.85
3. Paved Area 10092.39 0.7 11 0.011 83.26 20.82
Total Runoff (m3 /hr) 179.65 44.91
Table-8: Numbers of RWH Structure Calculation
Runoff in No. of No. of

S. No. Diameter of the Depth of the Volume of
15 minutes structures structures
structure (m) structure (m) the Pit(m3)
(m3) required proposed
1. 4 3 37.68 44.91 1.19 5
As per the calculation provided above, we are proposing 5 nos. of RWH structure.
2.8. What would be the impact of the land use changes occurring due to the proposed project
on the runoff characteristics (quantitative as well as qualitative) of the area in the post
construction phase on a long term basis? Would it aggravate the problems of flooding or
water logging in any way?
 There will not be such impact as the proposed project will be developed on a land base which
is for “cultural” purpose as per the Delhi Master Plan 2021.
 As the project site is almost plain land and the topography of the site is not anticipated to
change due to the project activities, hence, no impacts are expected on the drainage profile or
runoff characteristics after construction phase.

 A network of storm water drain is proposed all along the direction along the main roads and
cross roads of suitable area size. All storm water drains will be covered with RC slabs so as to
prevent the entry of soil and dust. Storm water collected through storm water drains and
discharged into existing Storm Water Drains. Storm water drains will be constructed on all
the edges of roads.
 The proposed project will have a storm water management system aiming at “Maximum uses
of Storm water.” The system will include collection of storm water and roof-top rainwater
and stored through designed RWH structure. Excess storm water will be discharged outside
of the project site through a drainage system. The proposed project would not aggravate the
problems of flooding or water logging in anyway.
2.9 What are the impacts of the proposal on the ground water? (Will there be tapping of
ground water; give the details of ground water table, recharging capacity, and approvals
obtained from competent authority, if any)
Adequate management measures are being taken to protect the water quality during construction
phase. Excavation during monsoon season will be avoided. Care is being taken to avoid soil
erosion. To prevent surface and ground water contamination by oil/grease, leak proof containers
shall be used for storage and transportation of oil/grease. The floors of oil/grease handling area
shall be kept effectively impervious. Collection and settling of storm water, prohibition of
equipment wash downs, and prevention of soil loss and toxic release from the construction site
will be adhered to minimize water pollution. Figure-9 and Figure-10 shows Hydrogeology map
of India and categorization of Blocks. Figure-11 shows Depth to water level in post monsoon.
Figure-12 shows area identified for artificial recharge in Delhi.
Project Site
Figure-9: Hydrological map of India

Project Site
Figure-10: Categorization of Blocks
Project Site
Figure-11: Depth to Water level (Post Monsoon)

Project Site
Figure-12: Areas identified for Artificial Recharge in Delhi
2.9. What precautions/measures are taken to prevent the runoff from construction activities
polluting land & aquifers? (Give details of quantities and the measures taken to avoid the
adverse impacts)
The construction shall be taken up on a piece of land within the existing Public and semi-public
area which is enclosed from three side. As such there shall not be major impact due to the runoff
from construction activities. However, a channel shall be prepared to collect the surface runoff
during rains to collect at a place which shall be disposed off to existing storm water drain.
In operation phase most of the storm water produced on site will be harvested through rain water
harvested structure. Thus proper management of this resource must be ensured so that it is free of
contamination. A detailed Storm Water Management Plan will be developed which will consider
the sources of storm water. The plan will incorporate best management practices which will
include the following:
 Regular inspection and cleaning of storm drains.

 Installation of clarifiers or Oil/Water separators system of adequate capacity around
parking areas and garages as per requirement.
 Cover waste storage areas.
 Avoid application of pesticides and herbicides before wet season.
 Conducting routine inspections to ensure cleanliness.

 Preparation of spill response plans, particularly for fuel and oil storage areas.
 Provision of silt traps in storm water drains.
 Good housekeeping in the above areas.
Precautions /Measures Taken to Prevent the Run-Off from Construction Activities

• Domestic Wastewater from Toilets: Additional generation of sewage is not envisaged to be
treated and disposed off separately. Existing sewage line with toilet facilities shall be used by
then involved construction workers and staff.
• Site Development and Construction: The wastewater generation during site development
and construction mainly includes the storm water run-off from the construction areas,
stockpiles of construction materials and wastes, etc. mainly containing high suspended solids
(SS), in case these activities are undertaken during rainy season.
2.10. How is the storm water from within the site managed? (State the provisions made to avoid
flooding of the area, details of the drainage facilities provided along with a site layout
indication contour levels).
As the ground water table is very high i.e. 2.5 m below the existing ground level. So, RWH pits
are not feasible. Therefore, we are proposing the rain water harvesting structure for the direct use
or for water harvesting. Most of the storm water will be managed through Rain water harvesting
technology. The storm water management plan will include practices as stated in point 2.7 & 2.8
2.11. Will the deployment of construction laborers particularly in the peak period lead to
unsanitary conditions around the project site (Justify with proper explanation).
No it shall not lead to unsanitary conditions. Additional generation of sewage is not envisaged to
be treated and disposed off separately. Existing sewage line with toilet facilities shall be used by
then involved construction workers and staff.
2.12. What on-site facilities are provided for the collection, treatment & safe disposal of sewage?
(Give details of the quantities of wastewater generation, treatment capacities with
technology & facilities for recycling and disposal).
There is a provision of the onsite STP to treat the sewage. The treatment of sewage generated
from the site will be done in proposed Sewage treatment of capacity 320 KLD.

Fluidised Bed Reactor (FBR)
A fluidized bed reactor (FBR) is a type of reactor device that can be used to carry out a variety of
multiphase chemical reactions. In this type of reactor, a fluid (gas or liquid) is passed through a
solid granular material (usually a catalyst possibly shaped as tiny spheres) at high enough
velocities to suspend the solid and cause it to behave as though it were a fluid. This process,
known as fluidization, imparts many important advantages to the FBR. As a result, the fluidized
bed reactor is now used in many industrial applications.
The solid substrate (the catalytic material upon which chemical species react) material in the
fluidized bed reactor is typically supported by a porous plate, known as a distributor. The fluid is
then forced through the distributor up t hrough the solid material. At lower fluid velocities, the
solids remain in place as the fluid passes through the voids in the material. This is known as a
packed bed reactor. As the fluid velocity is increased, the reactor will reach a s tage where the
force of the fluid on the solids is enough to balance the weight of the solid material. This stage is
known as incipient fluidization and occurs at this minimum fluidization velocity. Once this
minimum velocity is surpassed, the contents of the reactor bed begin to expand and swirl around
much like an agitated tank or boiling pot of water. The reactor is now a fluidized bed. Depending
on the operating conditions and properties of solid phase various flow regimes can be observed
in this reactor.
2.13. Give details of dual plumbing system if treated waste is used for flushing of toilets or any
other use.
Dual plumbing system that utilizes separate piping systems for freshwater and recycled
wastewater will be adopted for the project. Treated water from the STP is estimated at 320 KLD.
The recycled water system shall utilize this treated water and serve for non-contact uses such as
flushing, horticulture, DG Cooling etc.
3. VEGETATION
3.1. Is there any threat of the project to the biodiversity? (Give a description of the local
ecosystem with its unique features, if any)
Okhla Bird Sanctuary is coming within the 8.78 km radius of the project site which may have an
indirect impact.
Local eco-system has the unique features of north western plains sub zone of upper gangetic
plain agro climatic zone. The climate of the area varies from dry sub humid to semi arid and soil
type is mainly alluvial. Numerous alluvial landforms such as marshes ox-bow lakes, meander-
cuts, peniplain and pedyplain are unique features of local ecosystem. The major tree found in the
study area involves Bahuinia variegata, Delonix regia etc. The area is very fertile and numerous
agricultural crops i.e. wheat and mustard are grown.
3.2. Will the construction involve extensive clearing or modification of vegetation? (Provide a
detailed account of the trees & vegetation affected by the project)
The construction will not involve any extensive clearing or modification of vegetation. As the
land is a Government owned land by Delhi Development Authority no forest land is involved in
the construction of proposed project site.
3.3. What are the measures proposed to be taken to minimize the likely impacts on important
site features (Give details of proposal for tree plantation, landscaping, creation of water
bodies etc along with a layout plan to an appropriate scale?)
The following steps were taken to minimize the likely impacts on the surrounding environment.
• The Green Belt is proposed for clean, healthy and beautiful green environment for the
people to live in and work in.
• Within the proposed project site green belt to be developed by plantation of various
species of plants, shrubs to create a clean, healthy and aesthetic environment that
provides a visual retreat and relaxation to the occupants of the project. A combination of
evergreen trees and ornamental flowering trees and shrubs recommended by CPCB.
• The plantation arrangement would be based on optimal use of available land and
quantum of irrigation water and treated waste water.
• The capability of plants to act as a s ink for air contaminants has been addressed by a
number of reviews. Various studies indicate that the surface of vegetation provides a
major filtration and reaction surface to the atmosphere for removing pollutants from the
atmosphere. Therefore, the green belt is essential feature of any developmental project
because it acts as a pollution cleaning region, improvement of the aesthetic value of the
project and a noise buffer.

Table-9: List of Species for Greenbelt Development

Crown Leaf
Common Sensitive/ Height Crown Surface Area Area Stomatal
S.No Binomial Name Family Name Hindi Name Tolerant (M) Flowering Season Shape M2 CM2 Index
Silver
1 Acacia dealbata Link Mimoseae Wattle Tolerant 15m April-June Oblong
Indian
Acacia nilotica (Linn) Gum-
2 Willd. Mimoseae Arabic-tree Babul Tolerant 8m Aug-JAN. Spreading 8294 136 11
Albizia moluccana White Subabul, Tolerant
3 Mig Mimoseae popinae Vilaitibaral 15m July - Oct. Oblong
Alstonia scholaris Tolerant
4 (linn.)R. Br. Apocynaceae Chattiyan 15m Dec - Mar. Round 241681 52 15
Tolerant March -July
Anona swuamosa Custard extended up to
5 Linn. Anonaceae apple Seetaphal 10m sept. Round 2178 54 26
Anona reticulata Bullock's Tolerant
6 Linn. Anonaceae Heart Luvuni, nona 10m June. Round 2017 51 17
Azadirachta indica A. Tolerant Jan - March, Aug.
7 juss. Meliaceae Indian Lilac Nim 20m - Sept. Spreading 300445 84 29
Balanites roxburghiji Tolerant
8 planch Balanitaceae Desert-date Hingan 9m April-June Spreading
Barringtonia Barringtoniacea Tolerant March-May, Sept-
9 acutangula (l)Gaertn e Indian Oak Hijal 9-12m Oct. Spreading
Yellow Tolerant
10 Cassia pumila Lamk Caesalpinaceae Cassia 10-12m Round 13274 118 20
Iron wood Minjri Tolerant
11 Cassia siamea Lamk Caesalpinaceae tree (Beng.) 10-12m Aug - May Oblong 3927 138 21
Australian Tolerant
or
Casuarina Whistling Feb. -April, Sept-
12 equisetifolia Linn. Caesalpinaceae pine Jangli saru 10m OCT Oblong
Citrus aurantium Tolerant Round/
13 Linn Rutaceae Limbu 5m Sept - Nov Oblong 495 20 36
Clerodendrum inerme Tolerant
14 (Linn) Gaertn verbenaceae Vanjai 5m Nov - Jan Round 723 42 18
15 Derris indica Fabaceae Pongam-Oil Karanja Tolerant 10m April - June Round 6278 80 25

Crown Leaf
(Lam.)Bennett. Tree,
Karanj
Tolerant Throughout the
16 Duranta repens L verbenaceae 3m year Spreading 60 63 22
Mysore Tolerant Feb. -April, Oct.-
17 Eucalyptus hybrid Myrtaceae gum 20m Dec. Conical 50047 50 13
Ficus benghalensis Banyan Tolerant
18 Linn Moraceae Tree Bargad 20m April - June Spreading 236494 119 22
19 Ficus benjamina Linn Moraceae Pakur Tolerant 12m Sept - Nov Spreading 87326 29 19
Indian Tolerant
Rubber Spreading/
20 Ficus elastica Roxb Moraceae Tree 12m Round 6028 94 19
Korotosani(O Tolerant
21 Ficus gibbosa Blume Moraceae risa) 10m April - May Spreading 223,45.4 40 20
Tolerant Round/
22 Ficus religiosa Linn Moraceae Peepal Tree Pipal 20m Jan.- May. Oblong 1,44,868.7 114 19
23 Ficus virens Ait Moraceae Pilkhan Tolerant 10m Jan.- May. Oblong 1,97,838.2 43 16
Tolerant April - Aug
Gardenia tasminoides Extended up to
24 Eills Rubiaceae 5m Sept. Oblong 266 58 19
Grevillea robusta A. Silvery or Tolerant
25 Cunn. Proteaceae Silky oak 20m Feb - April Oblong
Guazma ulmifolia Tolerant Round/
26 Lamk Sterculiaceae Rudraki 10m Mar - August. Spreading 30280 85 13
Heterophragma Tolerant Round/
27 roxburghiji DC Bignoniaceae 18m Feb. - April. Oblong 155218 35 14
Hibiscuc rosa- Tolerant Throughout the Round
28 sinensis Linn Malvaceae Jasud Jasum 3m year /Oblong 61 45 23
Tolerant Throughout the
29 Lxora coccinea L Rubiaceae Rangan 6m year Oblong 183 70 23
Tolerant More or Less
throughout the
30 Lxora Rosea Rubiaceae 6m year Oblong 296 62 20

Crown Leaf
Kigelia africana Sausage Tolerant Round/
31 Lamk Bingnoniaceae tree 10m Mar.- June Oblong 58432 268 13
Lagerstroemia Queen Tolerant
32 speciosa (Linn) Lythraceae crape Myrte Jarool 10m April - June. Oblong 72569 88 14
Managifera indica The mango South India -Jan - Round /
33 Linn Anacardiaceae tree Am Sensitive 15m Mar Oblong 69005 85 31
Round /
34 Milletia pequensis Ali Fabaceae Tolerant 10m Aug. - Oct. Oblong 42312 167 12
Indian
Millingtonia hortensis cork- tree, Oblong /
35 L.F Bignoniaceae Buch Sensitive 10m Oct.- Dec. Round 22439 139 18
Mimusops hexandra Oblong /
36 Roxb. Sapotaceae Khirni Tolerant 10m Sept - Nov Round 4063 89 20
37 Morus alba Linn. Moraceae Tuti Tut Sensitive 8m Feb.- June Oblong 1048 285 17
Peltophorum Tolerant
pterocarpum Copper pod Oblong /
38 (DC)Backer Caesalpinaceae tree. May - Sept. Round 231045 371 17
Manila Tolerant
Pithecellobium ducle tamarind,M
39 (Roxb.) Benth Mimosaceae adras thorn Vilayatimili 8m Jan. - Feb. Oblong 2565 183 12
Prosopis chilensis Vilayati Tolerant
40 (Molina)Stuntz Mimosaceae Mesquite kikkar 10m Dec. - April. Spreading 7951 51 19
Prosopis cineraria Tolerant
41 Linn. Mimosaceae Khejri 12m Dec. - April. Spreading 13431 54 18
Psidium Guayava Tolerant
42 Linn. Myrtaceae Guava tree Amrud 5m Oblong 9243 54 28
Tolerant Spreading
43 Samanea saman Jacq Mimosaceae Rain Tree 20m Mar. - June. /Round 99306 283 16
Sapindus emarginatus Tolerant Oblong /
44 Vihl Sapindaceae Soapnut 10m Oct. - Dec. Round 43789 111 24
Saraca asoka Tolerant
45 Roxb.De Wilde Caesalpinaceae Ashok 5m Dec. - May Spreading 2295 69 18
Sesbania grandiflora Swamp- Ogosti Tolerant
46 Pers Fabaceae pea,Agathi (Oriya) 10m Sept. - Dec. Oblong 4695 130 20

Crown Leaf
Sesbania sesban Common Tolerant
47 (Linn)Merrill Fabaceae Sesban Jainti 6m Aug. - Dec. Oblong 4564 118 19
Spathaodea Indian Tolerant Oblong/
48 campanulata Beauv Bingnoniaceae Tulip Tree 12m Nov. - Jan. Round 73250 89 25
Spondias pinnata Tolerant
49 (L.f) Anacardiaceae Tolerant 10m Feb - April Round 25587 131 23
Oblong/
50 Syzygium cumini Linn Myrtaceae Black plum Jaman Tolerant 20m Mar. - May. Spreading 112143 78 21
The
Tamarindus indica Tamarind
51 Linn Caesalpinaceae Tree Imli Tolerant 20m April - Oct. Spreading 276840 129 18
Thespesia
populeneoides(Roxb) Umbrella
52 Kostel Malvaceae Tree Paraspipal Tolerant 10m Through the year Round 34635 184 30
Thuja occidentalis American
53 Linn. Cupressaceae Arborvitae, White cedar Tolerant 15m Conical
Terma orientalis Charcoal Gio Indian Throughout the Round/
54 Blume Ulmaceae Tree, nettle tree Tolerant 6m year Oblong 425734 66 27
Zizyphus mauritiana Indian
55 Var. Fruticosa Rhamnaceae Jujube Ber Tolerant 10m April -Oct. Round 2638 24 12

4. FAUNA
4.1. Is there likely to be any displacement of fauna- both terrestrial and aquatic or creation of
barriers for their movement? Provide the details.
The proposed site is an open land when the construction begins and devoid of forestation so in
the existing conditions, this place was not the habitat for any wild fauna. There will not be any
type of displacement or any other effect on the local fauna due to proposed project activities.
4.2. Any direct or indirect impacts on the avifauna of the area? Provide details.
The following impacts to be observed after completion of the project.
• After green belt development, the planted trees and shrubs will provide shelters and shed
especially to the birds and other domesticated animals and human being.
• Within the proposed project site, proper landscaping has been planned to provide a clean,
healthy, and beautiful green environment for the people to live and work in.
• The common native variety of trees and ornamental flowering species will be planted in
the green space.
• The vibration raised during construction will affect the movement of birds during day
time.
• The monitoring to be done for regular checkup of the pollution raised by construction
activities. That should not above the prescribed limit as per CPCB norms.
4.3. Prescribe measures such as corridors, fish ladders etc to mitigate adverse impacts on
fauna.
These measures are not applicable for this project.
5. AIR ENVIRONMENT
5.1. Will the project increase atmospheric concentration of gases & result in heat islands? (Give
details of background air quality levels with predicted values based on dispersion models
taking into account the increased traffic generation as a result of the proposed
constructions)
Increased traffic generation due to proposed project is not going to cause significant increase in
atmospheric concentration of gases and will not result in island formation.
Background Air Quality:
The Air monitoring analysis report given below of the proposed project site and the background
air quality results are provided in the Table-10.

Table-10: Air quality monitoring Result
Results NAAQS
S.No Parameter Location Units Test Method
(mg/m³)
Particulate Matter
1 μg/m3 128 100 (24 Hourly) IS 5182(Pt-23)
as PM10
Particulate Matter ELPL/SOP-
2 μg/m3 58.1 060 (24 Hourly)
as PM2.5 Air/06
Sulphur Dioxide Temple
3 μg/m3 18.4 080 (24 Hourly) IS 5182 (Pt-02)
as SO2 Roof
Oxides of
4 μg/m3 33.7 080 (24 Hourly) IS 5182 (Pt-06)
Nitrogen as NO2
Carbon mg/m
5 3 1.02 002 (08 Hourly) IS 5182 (Pt-10)
monoxide(CO)
The Monitoring Reports are attached as Annexure-VIII.

5.2. What are the impacts on generation of dust, smoke, odorous fumes or other hazardous
gases? Give details in relation to all the meteorological parameters.
Construction Phase:
During construction phase there is increased generation of dust and smoke from the background
levels. There is no activity associated with generation of odorous fumes and any hazardous gases
during construction phase.
The main sources of dust generation are land clearing, drilling, ground excavation, cut and fill
operations (i.e., earth moving), and construction of a particular facility. A large portion of the
dust emissions results from equipment traffic over temporary roads at the construction site.
Measures taken during Transport and Handling of Materials during Construction

The transport and handling of materials during construction has potential impacts on air quality
in the vicinity. Thus the following mitigation measures are being adopted to minimize the
impacts.

Air Emissions
• Dust Suppression: The most cost-effective dust suppressant applied to mitigate airborne
dust is water, because of its efficiency as well as ready availability on the construction site.
Water shall be applied using handheld sprays and automatic sprinkler systems. Water spray
at the work site also effectively suppresses dust generated. Results have proven that for about
80% of such active area(s), the water spray suppresses airborne dust by about >90%.
Table-11: EMP for Dust Suppression

Sources/Process Emission Scope of Control Effectiveness
Potential
Hydraulic excavators and High when Use of water sprays to moisten material Moderate
loaders (e.g Front loader, dry or fine being handled. Soils may be subject to a
backhoe face shovel silty material soil moisture content planning condition
bulldozers) for the are being
excavation, lifting and handled,
movement of material particularly
such as Soil, overburden. during strong
windy
weather
Low when Minimize drop heights when unloading
coarse or wet material. Protect from exposure to wind
material are where possible.
being handled
during
conditions of
low wind
speed
Vehicles for transport of High Minimize onsite transportation distances. High
material within the site. particularly
when Use of water sprays to moisten road
travelling surfaces during dry weather.
over Use mechanical road sweepers during dry
unsurfaced weather, to, limit v isible dust emissions.
and dry site Restrict vehicle speeds through
roads. signage/staff training.
Use of covered conveyors to transport
material around the site.
• Emission Control for Construction Equipment/Vehicles: Construction equipment and

heavy transport vehicles meet emission standards like Bharat Stage - IV requirements for
vehicles. The operation and maintenance of all vehicles, equipments deployed on s ite by
different contractors are being regulated and effectively monitored. The Pollution under
Control (PUC) certification is being ensured for proper O&M of vehicles.
• Improved Maintenance: Recognizing that significant emission reductions can be achieved

through regular equipment and vehicle maintenance, all site contractors have been asked to
take necessary steps for proper maintenance of vehicle and equipments. A monetary
incentive/ disincentive provision encourages contractors to comply with regular maintenance
requirements. The fuel used in the equipments, and vehicles is of good quality with low
“Sulphur” percentage by following the norms prevailing in project area.
• Reduction of On-site Construction Time: The heavy construction activities are being
confined to the daytime to avoid higher impacts during the nighttime. During daytime, there
is higher atmospheric dilution. Rapid on-site construction reduces the duration of traffic
interference and therefore, reduces emissions from traffic delay. Off-site fabrication of
various moulded structural components, obtaining proper cut size of stone, pre-fabricated
concrete slabs, etc. also enhance the quality of work environment at the construction site
because other factors such as traffic congestion and emissions are then not relevant.
• Barrier around the Site: Besides the project site will be enclosed by about 2.5 m high
temporary barrier during the whole construction period so that the spread of dust to the
neighborhood shall be restricted.
Operation Phase:
The land use of the site will be designed to have open areas covered with either soft or hard
landscape and paved areas (roads and pedestrian walkways). This will mitigate dust emissions in
any meteorological conditions.
5.3. Will the proposal create shortage of parking space for vehicles? Furnish details of the
present level of transport infrastructure and measures proposed for improvement
including the traffic management at the entry & exit to the project site.
No, the proposed project will not create shortage of parking space for the vehicle. 635 ECS is
provided in the basement and on surface.
5.4. Provide details of the movement patterns with internal roads, bicycle tracks, pedestrian
pathways, footpaths etc., with areas under each category.
Internal road width of 6 meters is proposed for internal traffic management.

5.5. Will there be significant increase in traffic noise & vibrations? Give details of the sources
and the measures proposed for mitigation of the above.
Sources of traffic noise & vibrations in construction phase:
Construction vehicles (Majorly Trucks & JCBs, Road rollers etc.)
The trucks carrying materials such as concrete bags, construction debris etc. will be serviced
regularly and there will be speed limit for all the vehicles moving within the project site. Proper
maintenance of the internal roads will be carried out, encourage vehicle owners to not to blow
horns. The movements of vehicles have been restricted to day time so as to reduce the
disturbances in nearby areas of project site during night.
Sources of traffic noise in operation phase:

Light motor vehicles & 2-wheelers. There will be negligible effect of vibration from movement
of light vehicles and 2 wheelers. To mitigate the noise effects vehicle owners will be encouraged
for regular checks of their vehicles.
Moreover the effect of noise will be further minimized by plantation on t he sides of internal
roads, on the open spaces inside and around the periphery of whole project site.
5.6. What will be the impact of DG sets & other equipment on noise levels & vibration in &
ambient air quality around the project site? Provide details.
In case of power failure, 3 DG sets of total capacity of 3030 kVA (3 x 1010) will be provided as
power back-up for the essential load.
The DG sets will be of water- cooled.
Calculation of DG Stack Height:

Stack Height for D.G. set capacity more than 1000 KVA:
H=14*Q0.3------- (As per CPCB norms for D.G. sets commissioned after 1.7.2003)
Where,
H= Maximum Stack Height in Meter (m)
Q= Total SO2 emissions from D.G. sets in kg/hour

Sulphur content in HSD =0.25%

Density of HSD= 0.85 kg/liter
D.G. Set combined Capacity = 3,030 KVA

Fuel Consumption for D.G sets capacity of 3030 KVA = 460 lit/hour
D.G. Set of combined Capacity = 4500 KVA (2x 2000+1x 500)
Density of HSD= 0.85 kg/liter
Emission of Sulphur = 1.15 Lit/hour * 0.85 Kg/Lit * (0.25/100) =1.995Kg/hour
Applying,
H= 14*Q0.3
= 16.41 ~ 17 m
We suggest 6 meter above the max. height of the building.
Impact of D.G. sets on noise & vibration and mitigation measures to be adopted in
construction and operational phase:
D.G. sets if not enclosed in acoustic enclosures will contribute to significant increase in noise
levels at the project site.
However the D.G. sets used during construction and operation phase will be enclosed in an
acoustic enclosure to reduce the noise. The DG sets foundation will comprise of heavy weight
inertia concrete block. No vibration impacts are expected from the DG sets.
The D.G. sets will be checked for noise every 6 months.
The noise level of DG sets will be maximum 75dB (A) (at 1.0 m distance) & the insertion loss
will be maintained at minimum 25 db as per the prescribed compliance standards of the MoEF
{Noise pollution (regulation & control) (Amendment) rule 2010}.

Impact of D.G. sets on ambient air quality and mitigation measures to be adopted:
The D.G. Set emission consist of following pollutants
1. Hydrocarbon+ NOx
2. Carbon Monoxide (CO)
3. Particulate Matter (PM)
4. Smoke
If unchecked the emissions from D.G sets will increase the concentration of above mentioned
pollutants in the atmosphere. To mitigate the polluting effects of D.G. sets following mitigation
measures will be taken,
A. Use of High Speed Diesel as a fuel to run D.G. sets

B. Provision of stack with height as prescribed by Central Pollution Control Board.
C. Emission test of D.G. stacks every 6 months to check the concentration of pollutants.
6. AESTHETICS
6.1. Will the proposed constructions in any way result in the obstruction of a view, scenic
amenity or landscapes? Are these considerations taken into account by the proponents?
The site lies in well planned area designated for “cultural” purposes as per the master plan of
Delhi. Thus, no obs truction of view or scenic beauty or landscape is anticipated. Furthermore,
the construction is being done in such a way that the organized open spaces and landscaped areas
will render the plot aesthetically appealing.
6.2. Will there be any adverse impacts from new constructions on the existing structures? What
are the considerations taken into account?
There will not be any adverse impacts from new constructions on the existing structures as the
proposed development shall be carried out as per the defined Delhi building by-laws. All
precautions are being taken to mitigate the impact due to water air and noise pollution during
construction the construction phase and same will be followed during the operation phase.
6.3. Whether there are any local considerations of urban form & urban design influencing the
design criteria? They may be explicitly spelt out.
There is no local consideration of urban form and urban design criteria. The proposed project
will be constructed within the designated site as per the defined building bye laws of Delhi.
6.4. Are there any anthropological or archaeological sites or artifact nearby? State if any other
significant features in the vicinity of the proposed site have been considered.
Since, all the activities whether during the construction or operation stage, will be carried out in
the project premises hence no impact on any type of archeological monuments are envisaged.
7. SOCIO-ECONOMIC ASPECTS
7.1. Will the proposal result in any changes to the demographic structure of local population?
Provide the details.
Establishment of any project plotted development leads to socio-economic changes. Influx of
population leads to change in social & economic status of the community. During construction
period local people will be engaged and hence there will be demand of 700 w orkers (peak
labour), till construction complete. The different features/facility mentioned above requires
skilled personnel to operate the individual facility. Also there shall be requirement of domestic
workers and maids. So there shall be indirect increment in employment opportunities and
additional income.
7.2. Give details of the existing social infrastructure around the proposed project.
School:
Guru Harkrishan Public School, India Gate Approx. 1.09 Km, NW
Mater Dei school, Tilak lane Approx. 1.04 km , NW
Indian Society of International Law Approx. 1.26 km , NNW
Hospital:
Diwan Chand hospital Approx. 2.8 km, NE
Sanjeevan hospital Approx. 3.36 km, N
Guru Nayak Eye Centre Approx. 3.26 Km, NNW
7.3. Will the project cause adverse effects on local communities, disturbance to sacred sites or
other cultural values? What are the safeguards proposed?
No, the proposed development will not have adverse effects on local communities. On the
contrary, it is expected that there will be major positive impacts due to development of the
proposed project. Positive impacts would include improvement in economic condition of society
indirectly. Respect to the local sacred sites and other cultural phenomena will be the integral part
of the proposed project.

8. BUILDING MATERIALS
8.1. May involve the use of building materials with high-embodied energy. Are the construction
materials produced with energy efficient processes? (Give details of energy conservation
measures in the selection of building materials and their energy efficiency).
The main construction materials being utilized in the construction of the proposed project
include cement ,stone aggregate, Coarse sand/fine sand, Steel, Sand Stone, Granite/Marble,
Bricks, and Blocks, glass etc.
The embodied energy content of the material is given in Table-12.
Table-12: Embodied Energy Content of the Material
Primary Energy
Primary Energy
Materials Requirement
Requirement
(Gj/tonne)
Aluminum 200-250
Stainless steel 50-100
Plastic 100+
Very High Energy
Copper 100+
Steel 30-60
Lead 25+
Glass 12-25
Cement 5-8
High Energy
Plasterboard 8-10
Lime 3-5
Clay bricks and 2-7
tiles 1-4
Medium Energy Gypsum Plaster <0.5
Concrete
Sand, aggregate
Source: Manual on norms and standards for environment clearance of large construction projects, MoEF
 These construction materials will be procured from the reputed suppliers/manufacturers and
thus it is expected that they are produced with energy efficient processes. Most of the quality
grade building material production facilities and industries now use energy efficient
processes.
 All the items to be used in the proposed project will be as per the National Building Code
specification. If the building materials with high-embodied energy are locally available, it
will be used in construction.
8.2. Transport and handling of materials during construction may result in pollution, noise &
public nuisance. What measures are taken to minimize the impacts?

The transport and handling of materials during construction phase has potential impacts on a ir
and noise emissions in the vicinity. To control this, various mitigation measures shall be adopted
to minimize the impacts.
Air Emissions
Dust Suppression: The most cost-effective dust suppressant applied to mitigate airborne dust is
water, because of its efficiency as well as ready availability on the construction site. Water is
being applied using water trucks, handheld sprays and automatic sprinkler systems. Water
spraying at the site also effectively suppresses dust generated. Results have proven that for about
80% of such active area(s), the water spray suppresses airborne dust by about >90%.
Emission Control for Construction Equipment/Vehicles: Construction equipment and heavy

transport vehicles meet emission standards like Bharat Stage - IV requirements for vehicles. The
operation and maintenance of all vehicles, equipments to be deployed on site by different
contractors shall be regulated and effectively monitored. The Pollution under Control (PUC)
certification are being ensured for proper O&M of vehicles.
Improved Maintenance: Recognizing that significant emission reductions can be achieved

through regular equipment and vehicle maintenance, all site contractors have been asked to take
necessary steps for proper maintenance of vehicle and equipments. A monetary incentive/
disincentive provision encourages contractors to comply with regular maintenance requirements.
The fuel to be used in the equipments, and vehicles shall be of good quality with low “Sulphur”
percentage by following the norms prevailing in project area.
Reduction of On-site Construction Time: The heavy construction activities will be confined to
the daytime to avoid higher impacts during the nighttime. During daytime, there will be higher
atmospheric dilution. Rapid on-site construction reduces the duration of traffic interference and
therefore, reduces emissions from traffic delay. Off-site fabrication of various moulded structural
components, obtaining proper cut size of stone, pre-fabricated concrete slabs, etc. shall also
enhance the quality of work environment at the construction site because other factors such as
traffic congestion and emissions are then not relevant.
Noise Emissions
 The mitigation measures concerning technological control at source (of vehicles) shall meet
the minimum compliance requirements for manufacturing stage. Besides these, other
measures shall be of preventive nature as follows:

 Restriction of Time of Construction: The heavy construction and transport activities will
be restricted to daytime operation when the background noise levels are high so that impacts
like sleep disturbance during the night time will be avoided.
 Provision of Noise Barrier: No extra barriers will be provided because it will be within the
premises of the project site.
 Proper Maintenance of Construction Equipment/Vehicles: Proper operation and
maintenance of heavy equipment as well as transport vehicles will be ensured for lower noise
emissions.
 Occupational & Passive Protection: Ear plugs, ear muffs, etc. will be provided to workers
handling high noise equipment or stone cutting operations shall protect them from high noise
exposure.
8.3. Are recycled materials used in roads and structures? State the extent of savings achieved?
Fly ash used materials would be utilized for paving work etc, if viable. Also, the construction
waste (particularly the construction debris) will be used on the project site for leveling purposes.
An approximate saving of 5% to 7% is proposed to be achieved.
8.4. Give details of the methods of collection, segregation& disposal of the garbage generated
during the operation phases of the project.
Solid Waste during Operation Phase
Solid waste and other waste to be generated from the proposed project will be classified as given
in Table-13.
Table-13: Classification of Solid Wastes and other Wastes
S. No. Types of Solid waste and other waste Description

Wastes from the kitchen including
1. Food Waste (garbage)*
preparation, cooking and serving of food.
Combustible (Primary Organic):
Paper, cardboard, cartons, wood, boxes,
plastics, rags, cloths, beddings, leather,
rubber, grass, leaves.
2. Rubbish*
Non-combustibles (Primary Inorganic):
Metals, tin cans, metals foils, dirt, stones,
bricks, ceramics, crockery, glass bottles,
other metal refuses.
Street sweeping, dirt, leaves, catch basin dirt,
3. Street Waste* animal dropping, contents of litter
receptacles dead animals.
4. Horticultural waste* Tree trimming, leaves, waste from parks and
gardens etc.
General domestic waste from office and
5. Paper, General Domestic Waste etc.
administration
Sludge generation after treatment of sewage
6. STP Sludge
in STP.
*Source: Manual on Municipal Solid Waste Management, published by Central Public Health and
Environmental Engineering Organization (CPHEEO), Ministry of Urban Development, Government of India.
 The proposed project is expected to generate certain types of wastes which would include
both non-hazardous and some hazardous wastes. The non-hazardous wastes generated at the
project would be municipal solid waste including paper & cardboard wastes, food wastes,
plastic wastes etc. STP sludge and other solid waste would also generate.
 It is estimated that total quantity of municipal solid waste generated will be approx. 1,687.5
kg / day, from the proposed project.
Collection:
The solid waste expected to be generated by the visitors and staff. A collection will be carried
out by private vendors.
Segregation:
 The solid waste expected to be generated by the population in the proposed project can be
broadly categorized into bio-degradable and non-biodegradable. These solid wastes will be
collected separately by putting three types of separate bins at the source of generation. For
the biodegradable waste green bins will be provided, for the recyclable waste blue bins and
for the non-recyclable waste dark grey bins will be provided.
Disposal:
• Biodegradable waste will be subjected to composting by Organic waste converter and
compost will be used as manure.
• Overall it would be ensured that all waste fractions are appropriately recycled/ disposed of
through authorized recyclers/re-refiners/contractors. Records will be kept regarding amount
and characteristics of all types of wastes.
• Paper & cardboard wastes, plastic wastes, metal wastes and other recyclable wastes will be
sold to authorized contractors.
• The STP sludge will be properly collect, store and used as manure or will be disposed
through authorized agencies/or used for horticultural purposes.

• As regards hazardous wastes, the building management staff of the proposed project will
review the proposed operations and make a thorough "applicability analysis" of the
Hazardous Waste Rules, to identify specific wastes, to be generated in the proposed project,
that shall be categorized as hazardous wastes. The management staff would then manage
hazardous waste as per the prevailing rules. The management staff of the proposed project
would ensure compliance with all the conditions on a continual basis.
• Hazardous wastes shall be stored in secured places with adequate secondary containment and
labelling as per the requirements of Hazardous Waste Rules.
• Appropriate records of hazardous wastes generation and disposal (in Form-3, Form-4, Form-
9, Form-13 etc.) shall be maintained as per the requirements of MoEFCC’s Rule.
9. ENERGY CONSERVATION
9.1. Give details of the power requirements, source of supply, backup source etc. What is the
energy consumption assumed per square foot of built-up area? How have you tried to
minimize energy consumption?
The total electrical load demand has been estimated to be 2,430 KW. The source of power will
be supplied by BSES Rajdhani Power Limited.
power back-up for the essential load. The DG sets will be of water cooled.
The DG sets will be provided with acoustic enclosure. Adequate stack heights of D.G. Sets will
be provided as per the stipulated guidelines of Central Pollution Control Board (CPCB) to
facilitate natural dispersion of exhaust gases.
Energy Conservation Measures:

 Fly ash bricks would be used.
 Use of LED lights in circulation area and in toilets.
 P.V. Cell system shall be installed for all street and compound lighting.
 The external surfaces of all the buildings will have granite stone cladding upto first floor
level and aluminum composite panels cladding above to have maintenance free external
façade of the building.
 All roofs shall be insulated with foam concrete to reduce the heat gain through the roof.
 Use of adequate window areas for getting natural light and ventilation.
 Use of electrical fittings, fans, A/C pumps and plants with star rating to save electricity
and improve energy efficiency.

Efforts shall be made to employ equipment, fixtures & systems which will conserve energy.
Following shall be considered towards energy conservation:
 Use of transformers with NO LOAD & ON LOAD watt losses as per ECBC.
 Use of high frequency, high power factor, electronic ballasts in place of conventional
copper-iron ballasts in light fixtures.
 Using energy efficient light fixtures with good photometric properties.
 Using LED in external lighting bollards, in areas such as staircases, corridors & lift
lobbies, where lights burn on 24 hrs. basis. Alternatively LED based fixtures shall be
used.
 Using T-5 (28W) fluorescent lamps in place of T-8 lamps (36W) in basements, stilts &
underground parking areas.
 Putting external lighting control on time switch / timer control.
 Using time switch control / timer control for basements lighting.
 Using LED light sources for some of the external lighting fixtures.
 Using solar powered lighting for part of the external lighting fixtures / garden landscape.
 Using high efficiency motors ‘EFF-1’ for pumps & ventilation fans.
 Capacitors shall have a long life in excess of 150,000 hours with low losses in the range
of 0.2 watt / KVAR.
To minimize the energy consumption & power load, building can be designed and constructed
according to Energy Conservation Building Code 2007 w hich sets minimum energy standards
for buildings.
The proposed project will adopt various energy conservation measures. The range of these
energy efficiency measures can be broadly categorized under:
• Architectural Design Features;

• Energy saving preventive practices; and
• Behavioral change and raising awareness.
Energy conservation program will include measures taken for both energy demand as well as
supply management.

Energy Conservation,
Monitoring & Management
SUPPLY DEMAND
system
• Reduce Consumption.
• Utililise Energy-efficient
equipment. • Use energy-efficient building designs
and ventilation systems.
• Exploring the possibilities of
utilizing renewable energy. • Create staff awareness and conduct
training programmes.
• Maximizing the use of Natural
lighting.
The Energy Conservation efforts may consist of the following mitigation measures:
a. Architectural Design Features
• Most of the external surface of the building will be design in way to have an air gap between
the wall surface and the external skin. This should reduce the transmission of heat into the
building as the heat would get dissipated into the air gap to an extent. Landscaping will be
carefully considered within the overall architectural concept.
b. Energy Saving Practices:

• Purchase of energy efficient appliances.
• Constant monitoring of energy consumption and defining targets for energy conservation.
• Adjusting the settings and illumination levels to ensure minimum energy used for desired
comfort levels.
• Use of Light Emitting Diodes (LED) and low voltage lighting.
c. Behavioral Change for Reducing the Consumption

• Train all staff and operators for energy efficiency measures.
• Promoting staffs’ awareness on energy conservation.
• Training of staffs on methods of energy conservation and to be vigilant of such opportunities.
• Turn on all lights when not in use, especially in conference rooms and turn down remaining
lighting levels where ever possible.

Passive Solar Design Considerations

Following are the consideration adopted for passive solar design of the buildings in the proposed
project:
• Maximum openings would be towards the north to get natural light that will not unduly heat
up the interiors.
• Least opening would be provided towards southern and western walls so as to cut out the hot
incident rays of the sun.
• Windows provided would be shaded adequately by designing double layer glass glazing so
that no direct rays of sun can come into the building.
Most of the external surface of the building will be designed in a way to have an air gap between
the wall surface and the external skin. This should reduce the transmission of heat into the
building as the heat would get dissipated into the air gap to an extent.
As an endnote, the design has been a conscious effort to make a modern building with local
materials and will not use excessive amount of glass and steel.
9.2 What type of, and capacity of, power back-up to you plan to provide?
The total electrical load demand has been estimated to be 2430 KW. The source of power will be
supplied by BSES Rajdhani Power Limited.
power back-up for the essential load. The DG sets will be of water cooled. The DG sets will be
of water cooled.
9.3. What are the characteristics of the glass you plan to use? Provide specifications of its
characteristics related to both short wave and long wave radiation?
Glass panel will have maximum light transmission but low solar heat radiation. This will reduce
quantity of heat inflow into the building. Single pane glass of 0.25 inches thickness with visible
transmittance up to 85% day lighting may be used.

Glass Assembly:
Single glazing for all frame types will have U-factor of 7.1 W/m2 o C, SHGC as 0.82 and VLT as
0.76.
Double glazing for wood, vinyl or fiberglass frame will have U-factor as 3.3 W/m2 o C, SHGC as
0.59 and VLT as 0.64.
Double glazing for metal and other frame type will have U-factor as 5.1 W/m2 o C, SHGC as 0.68
and VLT as 0.66
9.4. What passive solar architectural features are being used in the building? Illustrate the
applications made in the proposed project.
Passive solar design in Architecture: Solar design is the use of architectural features to replace
the use of grid electricity and fossil fuel with the use of solar energy and decrease the energy
needed in a home or building with insulation and efficient lighting and appliances.
Architectural features used in solar design include:

• Large south facing windows and minimum north-facing glazing.
• Use of materials with high thermal masses such as walls or roofs that absorbs and hold
the sun’s heat. Materials with high specific heat capacities, like stone, concrete, adobe or
water work bests.
• Insulation to reduce heat loss
• Sunspaces such as conservatories on s outh-facing elevations. These collect heat which
can be distributed throughout the building and reduce heat losses by creating thermal
buffer.
• Insulating shutters for windows to be closed at night and on overcast days. These trap the
solar heat in the building.
• Planting deciduous trees near the windows. The leaves will give shade in summer but
falls in winter to let the sunlight enter the building.
9.5. Does the layout of streets & buildings maximize the potential for solar energy devices?
Have you considered the use of street lighting, emergency lighting and solar hot water
systems for use in the building complex? Substantiate with details.
Yes, the streets and building is designed to maximize the potential of solar energy devices.

9.6. Is shading effectively used to reduce cooling/heating loads? What principles have been used
to maximize the shading of Walls on the East and the West and the Roof? How much
energy saving has been effected?
Yes. Shading has been effectively used to reduce the cooling loads. The following techniques
have been adopted:
• For walls on the east and west side of the building a maximum of 10% window to wall
ratio is recommend to minimize solar radiations, which further helps minimize
cooling/ventilation.
• Living areas to be aligned to get maximum north south light and services areas are to be
located on the western side.
• Shading is used to increase cooling effects in the building.
• There will be less numbers of openings on the west side and ore numbers of openings on
south side
• Projections such as balconies are provided on the south direction such that summer sun is
stopped and winter sun is let in.
• Promoting residents awareness on energy conservation.
9.7. Do the structures use energy-efficient space conditioning, lighting and mechanical systems?
Provide technical details. Provide details of the transformers and motor efficiencies,
lighting intensity and air-conditioning load assumptions? Are you using CFC and HCFC
free chillers? Provide specifications.
Suitable energy optimization will be adopted during the calculation of the energy load of the
proposed project. The space heating load will be minimized using passive solar structure,
suitable building envelop materials. Use of incandescent and halogen lamps will be avoided and
energy efficient compact fluorescent lamps /LED will be used for all common area.
9.8. What are the likely effects of the building activity in altering the micro-climates? Provide a
self-assessment on the likely impacts of the proposed construction on creation of heat island
& inversion effects?
Heat emission from the proposed construction can be from the following sources: Heat absorbed from
the paved and concrete structures, heat generated from equipments / appliances, and due to increased
population in the proposed project site. However the heat generated will not be significant and will be
dissipated in the lush greens and open areas provided within the project site. Hence it can be concluded
that the heat island effect shall not be a concern for the concerned project.

Moreover, Green cover will be provided at site and will incorporate such design considerations that
control formation of heat islands.
The buildup of indoor air contaminants is contributed by inadequate ventilation, contamination from
inside and outside the building, besides microbial contamination and contamination from building
fabric. The measures proposed for maintaining indoor air quality is presented in Table 14.
Table 14: Indoor air contaminants, Source and Health Effects
S.No. Indoor air Source Health Effects Measure to be
contaminant considered
1. Volatile organic Paints, Cleaning compounds , Nausea, Adequate
compounds glues, photocopiers, “Spirit Dizziness, Eye, ventilation
(VOCs) duplicators, signature respiratory tract,
machines, Tobacco smokes, mucous
dried out floor drains, membrane
cosmetics and other personal irritation,
products headache and
fatigue
2. Miscellaneous Window cleaners, acid drain Eye, respiratory Adequate
inorganic gases cleaners, combustion products, tract, mucous ventilation
which included tobacco smoked , blue print membrane
ammonia, equipment irritation ,
Hydrogen sulfide, aggravation of
sulphur dioxide chronic
respiratory
diseases.
3. Asbestos Insulation and other building Asbestos is Avoidance of use
material such as floor tiles dry normally not a of asbestos in
wall compounds, reinforces source of acute buildings and
plaster health effects. equipments to the
However, during extent possible.
renovation or
maintenance
operations
asbestos may be
dislodged and
become airborne.
4. Synthetic fibers Fibrous glass and mineral Irritation to the Avoid use of these
wool eyes, skin and material in
lungs dermatitis insulation
5. Carbon Dioxide Unvented gas, improperly Difficulty Proper venting
vented devices, processes or concentrating, any combustion
operations, which produce drowsiness, equipment.
combustion products, human increased
respiration. Respiration rate.

6. Carbon Monoxide Fossil-fuel engine exhausts, Dizziness, Adequate venting
improperly vented fossil-fuel headache, and ventilation.
appliances. nausea, cyanosis,
Cardiovascular
effects and death.
7. Nitrogen Oxides Combustion products from gas Eye, respiratory Adequate venting
furnaces and appliances, and mucous of combustion
tobacco smoke, welding, and membrane stacks.
gas and diesel engine exhausts. irritation.
8. Ozone Copy machines, electrostatic Eye, respiratory Adequate
air cleaners, electrical arcing, tract, ventilation.
and smog mucous
membrane
irritation;
aggravation of
chronic
respiratory
diseases.
9.9. What are the thermal characteristics of the building envelope? (a) roof; (b) external walls;
and (c) fenestration? Give details of the material used and the U-values or the R values of
the individual components.
The building envelope for external walls will be made of bricks, concrete and steel. The R and U
values building material will be considered as per ECBC norms at the designing stage. The
Thermal characteristic is provided in Table-15 below:
Table-15: Thermal Characteristic of Building

U-Factor R-Value
S.No. Building Envelope
(W/m2-ºC) (m2-ºC/W)
1 Roof 0.409 2.1
2 Opaque wall 0.44 2.1

SHGC:0.25(max)
3 Vertical Fenestration 3.30 (max.) (for WWR less than
or equal to 40%)
9.10. What precautions & safety measures are proposed against fire hazards? Furnish details of
emergency plans.

Adequate fire protection facilities will be installed including fire detectors, fire alarm and fire
fighting system. All fire protection facilities would be designed as per the National Building
Code.
Response in case of Fire

• Required response during in the event of a fire should be described in signs located in the
lobby.
• On sighting a fire, it should be immediately informed to the environment manager giving
the exact location and type of fire in detail.
• Initiate the Emergency Response Team for fires.
• If the fire is small, engage in extinguishing the fire using the nearest fire extinguisher.
• Guide the Emergency Response Team staff to the emergency assembly point.
• The Emergency Response Team should immediately inform the nearest dispensary and
security force. If required a fire tender should be summoned.
• The response team should immediately move to the point of fire and take all necessary
steps to stop the fire. If the fire is not controllable and spreads then the manager in charge
should inform the district authorities and call for external help.
• The Emergency Response Team will provide immediate relief to the injured residents at
the scene of incident. Any injured persons should be evacuated on priority to the
dispensary or one of the nearest hospitals based on their condition.
General Instructions for Occupants in case of Fire

• Get out of buildings as quickly and as safely as possible.
• Use the stairs to escape. When evacuating, stay low to the ground.
• If possible, cover mouth with a cloth to avoid inhaling smoke and gases.
• Close doors in each room after escaping to delay the spread of the fire.
• If in a room with a closed door.
• If smoke is pouring in around bottom of the door or if it feels hot, keep the door closed
• Open a window to escape or for fresh air while awaiting rescue.
• If there is no smoke at bottom or top and the door is not hot, then open the door slowly
• If there is too much smoke or fire in the hall, slam the door shut.
• Stay out of damaged buildings.
• Check that all wiring and utilities are safe.

Fire fighting system is proposed to prevent and control fire outbreaks for the project. The fire
fighting system will consist of portable fire extinguishers, hose reel, wet riser, yard hydrant,
automatic sprinkler system, and manual fire alarm system. The project will also be provided with
automatic fire detection and alarm system.
Schematic Fire Fighting Plan is attached as Annexure-IX

Risk Assessment and Management Plan is attached as Annexure-X
9.11. If you are using glass as wall material provides details and specifications including
emissivity and thermal characteristics.
Glass panel will have maximum light transmission but low solar heat radiation. This will reduce
quantity of heat inflow into the building. Single pane glass of 0.25 inches thickness with visible
transmittance up to 85% day lighting may be used.
The Double pane glass (clear/tinted) with a transmission coefficient of ‘U factor’ as 3.3 W/m2 -
ºC (for clear) and ‘U factor’ as 3.4 W/m2 -ºC (for tinted) may be used for composite climate
zone. The Solar heat gain coefficient (SHGC) is 0.59 (clear) and 0.42 (tinted).
9.12 What is the rate of air infiltration into the building? Provide details of how you are
mitigating the effects of infiltration.
Reduced air infiltration combined with proper ventilation can not only reduce energy bills but it
can also improve the quality of indoor air. Outdoor air that leaks indoor makes it difficult to
maintain comfort and energy efficiency. In addition, air leakage accounts for 25-40% energy
used for heating and cooling in a typical building. For this purpose the building has been
designed in a compact manner, leaving ventilation shaft in between buildings for facilitating the
escape of hot exhaust air.
9.13 To what extent the non-conventional energy technologies are utilized in the overall energy
consumption? Provide details of the renewable energy technologies used.
• The Energy efficient lighting will be done with the use of LED lamps. Additionally solar energy
will be explored.
• Use of Solar energy for street lightening will be explored.
10. ENVIRONMENT MANAGEMENT PLAN

10.1. The Environment Management Plan would consist of all mitigation measures for each item
wise activity to be undertaken during the construction, operation and the entire life cycle to
minimize adverse environmental impacts as a result of the activities of the project. It would
also delineate the environmental monitoring plan for compliance of various environmental

regulations. It will state the steps to be taken in case of emergency such as accidents at the
site including fire.
The mitigation measures suggested for the impacts identified on t he various environmental
components due to the project activities are given in this section. A detailed environmental
management plan is presented in Table-16 to mitigate all the identified environmental impacts
that are found to be significant.

Table-16: Environmental Management Plan – Construction Phase and Operational phase

S.No. Environmental Potential Potential Source Controls Impact Evaluation Remedial Measures
components Impacts of Impact Through EMP &
Design
1 Ground Water Ground Water Construction • Soak pit / septic No significant
Quality Contamination Phase tank will be impact as majority
• Sewage provided of labors would be
generated from locally deployed
temporary labor
tents.
Operation Phase • Proponent will No negative impact In an unlikely event of
• Sewage provide the STP to on ground water soil and ground water
Discharge from treat the sewage of quality envisaged. contamination.
the project Project. Not significant. Remediation measures
shall be implemented.
2. Ground Water Ground Water Construction • Not Applicable No significant
Quantity Depletion Phase impact on gr ound
• Ground water quantity
water will be not envisaged.
be used during
construction.
Operation Phase • Rain water No significant In an unlikely event of
• Groundwater harvesting scheme. impact on non-availability of
will not be used • Black and surface/ground water supply, water will
during operation Grey water water quantity be brought using
phase. The treatment and envisaged. tankers.
required water reuse.
will be met • Storm water
through the collection for
municipal supply water harvesting.
• Percolation
well to be
introduced in
landscape plan.
• Awareness
Campaign to
reduce the water
consumption
3. Surface Water Surface water Construction • Silt traps and No off site impact
Quality contamination Phase other measures envisaged as no
• Surface runoff such as additional surface water
from site during on site diversion receiving body is
construction ditches will be present in the core
activity. constructed to zone.
control surface
run-off during site
development
Operation Phase • Domestic waste No off site impact Excess of water will be
• Discharge of water will be envisaged discharged as per
domestic treated in STP CPCB standards.
wastewater to
STP.
4. Air Quality Dust Emissions Construction • Suitable control Not significant During construction
Phase measures will be because dust phase the contractors
• All heavy adopted for generation will be are advised to facilitate
construction subsiding the PM temporary and will masks for the labors.
activities level in the air as settle fast due to Water sprinklers will be
per air pollution dust suppression used for suppression of
control plan. techniques dust during
construction phase.
Emissions of Operational Phase • Rapid on-site Not significant. Regular monitoring of
PM10, PM2.5 , • Operation of construction and emissions and control
SO2, NO2 and construction improved measures will be taken
CO equipment and maintenance of to reduce the emission

vehicles during equipment levels.

site development.
Operation Phase • Use of low Not significant Use of Personal

sulphur diesel in There are no Protective Equipment
• Emission from vehicles and sensitive receptors (PPE) like earmuffs and
vehicular traffic machinery located within the earplugs during
in use Providing vicinity of site. construction activities.
Footpath and
Construction pedestrian ways
Phase within the site.
• Green belt will
• Operation of be developed with
construction specific species to
equipment and help to reduce PM
vehicle level
movements • Use of equipment
during site fitted with turbo
development. chargers
• Proper
maintenance o f
equipment
• Provision of
noise shields near
the heavy
construction
operations and
acoustic
enclosures for DG
sets
Construction
activity will be
limited to day time
hours only
5. Noise Operation Phase Green Belt No significant
Environment • Noise from Development impact due to
vehicular Green belt suitable width of
moveme development Greenbelt.
nt shall make a
barrier both for
noise and air
pollution.
6. Land Soil Construction • Construction No significant
Environment contamination Phase debris will be impact.
collected and Impact will be
• Disposal of suitably used on local, as waste
construction site as per the generated will be
debris solid waste reused for f illing
management of low lying areas
plan for etc.
construction
phase
Operation Phase • It is proposed Since solid waste
that the solid is handled by the
• Dumping of waste generated authorized
municipal solid will be managed agency, waste
waste on land. by an authorized dumping is not
agency. going to be
• Collection, allowed. Not
segregation, significant.
transportation
and disposal will Negligible impact.
be done as per

MSW
Management
Rule, 2000 b y
the authorized
agency
7. Biological Displacement of Construction Important The site has

Environment Flora and Fauna Phase species of trees, scanty vegetation
(Flora and on site if any, will be
Fauna) Site identified and
Development marked and will
during be planted for
construction landscape
development.
Operation Phase •Suitable green Beneficial impact.
belts will be
• Increase in developed as per
green cover landscaping plan
in and around the
site using local
flora
8. Socio- Employment Construction • Project No negative
Economic and livelihood Phase development as impact.
Environment options. Construction per the DDA
activities leading Master Plan
to gain in direct 2021.
& indirect
employment
Operation Phase • Project will Beneficial impact
provide direct
Site operation and indirect
employment

during the two

phases.
• Providing
quality-
Integrated
facility
9. Traffic Pattern Increase of Construction •Heavy No negative
vehicular traffic Phase Vehicular impact
• Heavy movement will
Vehicular be restricted to
movement daytime only and
during adequate parking
construction facility will be
provided
Operation Phase • Vehicular No major
• Traffic due movement will significant impact
to personal cars be regulated
inside the project
with adequate
roads and
parking lots in
the site.

Environmental Monitoring Plan

It is proposed to monitor essential parameters for ambient air quality, ambient noise quality,
ground water quality, and waste water quality both during the construction and operation phases
of the project. However the monitoring schedule for the compliance report is given in Table-17
Table-17: Environmental Monitoring Schedule for Compliance

S. No Particulars Monitoring Duration of Important Monitoring
Frequency Sampling Parameters
1 Ambient Air Quality Monitoring

Project site Once in 6 Months 24 hr continuously PM10, PM2.5,SO2, NO2&
except CO (8 CO
hourly)
3 Ambient Noise Level
Near DG set Once in 6 Months 8 hr continuous Noise level in dB(A)
with 1 hr interval
4 Ground/Drinking Water Quality Monitoring
Ground Water – Once in 6 Months Grab Sampling Parameters specified under
at project site IS:10500-2012
5 Soil Quality
At the green belt Twice in a year Samples will be Parameter for soil quality:
area collected from pH, texture, electrical
three different conductivity, organic
depths viz., 30cm, matter, nitrogen, phosphate,
60cm, and 100cm sodium, calcium, potassium
below the surface and Magnesium.
Environmental Monitoring:
Various environmental protection and mitigation measures have been suggested in the previous
Chapter/section for ensuring compliance with the stipulated environmental regulations and
applicable standards. Also, there are specified environmental monitoring and record keeping
requirements for operating facilities that the proposed Project will have to comply with. Though
record keeping would be largely an in-house activity, environmental monitoring within and
outside of the proposed Project would be carried out through recognized environmental
laboratories as per the requirements of MoEFCC.
The purpose of environmental monitoring is to evaluate the effectiveness of implementation of

EMP by periodically monitoring the important environmental parameters within the impact area,
so that any potential adverse impacts are detected and timely action can be taken. In order to

ensure compliance with the applicable regulatory requirements, the Project plans to conduct the
following environmental monitoring activities.
Wastewater Quality Monitoring and Record Keeping
The wastewater discharges from the proposed Project will mainly comprise of domestic sewage
and other wastewater discharges from drinking water points, toilets, washbasins, food court and
kitchen, backwashing of filters (used in water treatment) etc.
Therefore, as per the requirements of the Water (Prevention and Control of Pollution) Act 1974,
the Project proponent will apply to DPCC for the Consent to Establish. Before starting the
operation, the Project proponent will apply to DPCC for the Consent to Operate for Wastewater
Discharges and thereafter periodically renew its Consent to Operate. Subsequently, whenever
there is a change in the operations, the Project will get the requisite amendments in its Consent.
The Project would maintain an inventory of all sources of wastewater and maintain records of
waste water quality and quantity for the wastewater streams, as required. The Project will ensure
that wastewater analysis is conducted for all regulated parameters as per DPCC’s specification or
as per conditions of Consent to Operate and to ensure compliance with any other specifically
applicable standards. The frequency of wastewater quality monitoring would be decided in
consultation with the DPCC officials. Care will be taken to ensure that wastewater analysis is
conducted at such a frequency that potential variations due to various operational factors are
recorded.
Noise Level Monitoring and Record keeping

The Project would maintain an inventory of all point and non-point sources of noise emissions
and identify regulated sources, specified in the DPCC’s Consent to Operate for Air Emissions.
Main source of noise would be DG sets during the construction phase, But as DG s ets with
acoustic enclosure has been proposed, there would be minimal chance of noise pollution.
However, the Project management would conduct noise level monitoring at the specified
locations within, on t he fence line/boundary, and outside the Project’s premises to ensure
compliance with the specific standards and conditions of the Consent to Operate. The locations
of the noise monitoring stations and frequency of noise level monitoring would be decided in
consultation with the DPCC officials. The noise level monitoring would be conducted at such a
frequency that potential variations due to various operational factors are recorded.
Awareness and Training

Training and human resource development is an important link for achieving sustainable
operation of the facility and environmental management. For successful functioning of the

project, relevant EMPs will be communicated to the residents of the project. Everyone will be
made aware of importance of their various environmental responsibilities including waste
segregation and storage, water and energy conservation, etc. This awareness will be provided
through documents and periodic meetings. They will be informed of their responsibilities for
successful operation of various environmental management schemes inside the Project premises.
Relevant personnel at site will be trained for the following:
• Applicable EH&S regulations and compliance requirements for the same.

• Collection, Segregation, Storage and Disposal of solid and hazardous wastes.
• Operation and maintenance of Sewage Treatment Plant and recycling system
• Techniques for waste minimization, water conservation and energy conservation, etc.
• Functioning of the Project’s Environmental Management System (EMS) including
environmental monitoring, reporting and documentation needs.
• Requirements and responsibilities in case of an emergency as per emergency response plan.
Environmental Monitoring Program during Construction period

Based on t he above, the following environmental monitoring program during construction
activities is proposed for the Project. The monitoring program would be discussed and approved
by DPCC are given in Table-18.
Table-18: Proposed Monitoring Program for Construction Phase of the Project

Period and
S. No. Type Locations Parameters
Frequency
Ambient Air As per requirement SO2, NO2, PM10, PM2.5 As per DPCC’s
1. Quality and CO requirements
Monitoring
Ambient Noise As per requirement Noise level Leq both As per DPCC’s
2. Monitoring during day time and requirements
nighttime
Water Quality (i) Any operational Drinking water As per DPCC’s
Testing bore well parameters as per IS requirements
3. (Portability (ii) One of the 10500:2005.
testing) Drinking Water
Point
Treated Inlet and outlet of the Parameters for assessing As per DPCC’s
Wastewater STP compliance with requirements
4.
Quality standards for recycling
and horticulture use

Post-Project Environmental Monitoring Program

Based on t he above, the following post-project environmental monitoring program is proposed
for the Project. The monitoring program would be discussed and approved by DPCC are given in
Table-19.
Table-19: Proposed Monitoring Program for Operational Phase of the Project
Period and
S. No. Type Locations Parameters
Frequency
Ambient Air As per requirement SO2, NO2, PM 10, As per DPCC’s
1. Quality PM2.5 and CO requirements
Monitoring
Ambient Noise As per requirement Noise level Leq both As per DPCC’s
2. Monitoring during day time and requirements
night time
Water Quality (iii) Any operational Drinking water As per DPCC’s
Testing borewell parameters as per IS requirements
3. (Potability (iv) One of the 10500:2012.
testing) Drinking Water
Point
Treated Inlet and outlet of the Parameters for assessing As per DPCC’s
Wastewater STP compliance with requirements
4.
Quality standards for recycling
and horticulture use
Environmental Documentation
Documentation and reporting of environmental performance is an important management tool for
ensuring sustainable operation of the Project. Documents/Records shall be maintained for
regulatory, monitoring and operational issues. Typical documentation requirements for the
“Project” are summarized in Table-20.
Table-20: Environmental Documentation for Operational Phase of the Project
PARAMETER PARTICULARS
Air Emissions • Consent to Establish from DPCC
(incl. Noise) • Consent to Operate for Air Emissions from DPCC
• Ambient Air Quality Monitoring records
• Ambient Noise Monitoring Records
Water Supply • Water Quality Monitoring records
• Water Cess Returns
Wastewater • Consent to Establish from DPCC
Discharges • Consent to Operate for Wastewater Discharges from DPCC
• Details of quantity of wastewater discharged from various sources

PARAMETER PARTICULARS
and discharged from the outlet of the STP for recycling/into the
sewer
• Operational details of STP including number of hours of operation,
chemical usage, in-process wastewater quality, etc.
• Wastewater Quality and Quantity Monitoring records
Waste Management • Permission for disposal of solid wastes from concerned
municipality/authority
• Wastes Management Inventory including details of quantity of
wastes generated on-site and mode of their disposal
• Inventory of wastes stored on-site
• Records of hazardous wastes stored on-site (in Form-3) (if
generated)
• Annual Returns for hazardous wastes (in Form-4 and Form-13) to
DPCC
• Documentation related to off-site transportation and disposal of
hazardous wastes (including Form-9 and Form-10)
Environmental • Submission of Environmental Statement to DPCC before 30th
Statement September every year
Petroleum Storage • License from PESO for storage of HSD and other petroleum
substances (based on their quantities)
• Inventory of petroleum substances stored on-site both at storage
and usage locations
• Regular integrity testing/inspection reports for the storage tanks
Table-21: Environment Management Plan
Capital Cost Recurring Cost

Component
(Rs. in Lacs) (Rs. in Lacs)
Rain Water Harvesting System 15 2.3
Sewage Treatment Plant 96 48
Solid Waste Management 5 1
Environmental Monitoring -- 9
Green Area 3.5 0.5
Others (Energy saving devices, miscellaneous) 7 1.4
Total 126.50 62.20

CONCEPTUAL PLAN
1. INTRODUCTION
National Museum of Natural History (Ministry of Environment, Forests and Climate Change) is
going to develop a Museum Building Complex on the total land area measuring 26,299 sq.m.
The built up area is 46,025.78 sq.m.
The land is allotted the Ministry of Environment, Forests and Climate Change, GOI by Ministry
of Urban Development, GOI vide letter no. L-IIA-1(1377)/313 dated 18.12.2014. The copy of
the letter is attached as Annexure-I.
The development will be done is in accordance with Building byelaws of Delhi and will be
developed as per the master plan of Delhi. The Project is designated under Category “B” and
falls under Item 8(a) (Building & Construction) of the Environmental Impact Assessment (EIA)
Notification of September 14th, 2006 and its amendments.
2. SITE SURROUNDING & CONNECTIVITY

The proposed project site is connected to Noida, and other NCR regions. It is surrounded by
Kaka Nagar, Bapa nagar, Sanjay amar colony, Pandara Flats , Nizamudin.etc. residential areas
within 2km radius area of the proposed project site. Site surroundings and Connectivity details of
the proposed project are given in Table-1.
Table-1: Site Surroundings and Connectivity Details
S. No. Connectivity & Site Surroundings

Description Distance and Direction
Nearest Railway
1. New Delhi Railway Station Approx. 4 km, NNW
Station
2. Nearest Metro Station Indraprastha Metro station Approx.1.0 km, NNW
3. Nearest Airport Safdargunj Airport Approx. 4.78 km, SW
Kaka Nagar Approx. 1 Km , SE
Bapa Nagar Approx.81 Km, SE
Nearest Residential
4. Sanjay Amar Colony Approx. 1.41 Km , N
Area
Pandara Flats Approx. 1.9 Km , SSE
Nizamudin Approx. 1.9 km, S
5. State Boundary Delhi -UP state border Approx.6 km in SE
Delhi-Haryana border Approx.13 km, S

6. Nearest Highway and Bhairon Marg Adjacent to site, NW

Roads Mahatma Gandhi Marg Approx. 0.35 Km ,E
GT Road Approx.0.36 Km, E
Mathura road Approx. 0.55 Km , W
AH-2 Approx. 344.31 m, E
7. River / Drain Yamuna River approx. 0.73 km, East
MCD Drain Adjacent, North
Guru Harkrishan Public School, Approx. 1.09 Km, NW
India Gate
Mater Dei school, Tilak lane Approx. 1.04 km ,NW
8. Nearest School
Indian Society of International Approx. 1.26 km , NNW
Law
9. Nearest Hospital Sanjeevan hospital Approx. 3.36 km, N
Guru Nayak Eye Centre Approx. 3.26 Km, NNW

Sri Kilkari Baba Nath ji P ando Approx. 68 meter, W
Kaalin Mandir
Chandi Sheetla Mnadir Adjacent to site , S
10. Places of worship
Shri baba Dudhiya Bhairo Nath Adjacent to site, SW
ji Pandav Kallin
Matka Pir masjid Approx. 0.56 Km, NW
Jahanpanah City Forest Approx. 9.07 Km, S
Hauz Khas Forest Approx. 7.08 km, SSW
11. Forest * Central Ridge Reserve Forest Approx. 6.55 km , NW
Nothern ridge Forest Approx. 10.55 km, N
Rajokri PF Approx. 15.07 km , SW
Okhla Bird Sanctuary Approx. 8.78 Km , SSE
12 Sanctuaries
Asola Wild life sanctuary Approx. 16.27 Km, S
Archeological Old Fort Approx. 0.23 Km, W
Monuments India Gate Approx. 1.57 Km, WNW
Baroda House Approx. 1.65 Km, NNW
Supreme Court Approx. 1.38 Km, NNW
13
National Zoological Park Approx. 905.53 m, S
National Science Centre Approx. 225.49 m, N
National Handicrafts and Approx. 426.25 m, NW
Handlooms Museum
Parks Indraprastha park Approx. 2.03 km, SSE
13
Delhi Golf Club Approx. 1.65 Km , SSW

14 Power Station Gas turbine Power Station Approx. 1.25 Km, NNE
15 Industrial area Okhla Industrial area Approx. 9.07 Km ,South
Source: Google Earth
A Google Map of 500m buffer map showing the surrounding area of the proposed project is
shown in Figure-1.
The topographical map showing the surrounding area within 10 km radius is shown in the
Figure-2 and topographical map showing the eco-sensitive area within 15 km radius is shown in
the Figure-3.

Figure-1: Google Map of 500m radius showing surroundings of the area

Source: Survey of India
Figure-2: Topographical map (Survey of India) of 10km radius showing surrounding area

Figure-3: Topographical map (Survey of India) of 15km radius showing Eco-sensitive area

3. PROJECT LOCATION AND DESCRIPTION

National Museum of Natural History is going to develop a Museum Building Complex on the
26,299 sq.m. The built up area is 46,025.78 sq.m.
The coordinates of the project boundary along with the centre of the project site is given below
in the Table-2.
Table-2: Coordinates of the Project Boundary
Latitude Longitude
Centre of the Plot 28°36'39.57"N 77°14'48.46"E
Corner-I 28°36'39.69"N 77°14'43.89"E
Corner-II 28°36'40.14"N 77°14'44.39"E
Corner-III 28°36'40.38"N 77°14'44.67"E
Corner-IV 28°36'41.77"N 77°14'47.90"E
Corner-V 28°36'41.77"N 77°14'47.90"E
Corner-VI 28°36'42.46"N 77°14'48.59"E
Corner-VII 28°36'41.93"N 77°14'51.45"E
Corner-VIII 28°36'39.43"N 77°14'52.69"E
Corner-IX 28°36'39.27"N 77°14'53.04"E
Corner-X 28°36'36.14"N 77°14'45.86"E
Corner-XI 28°36'40.02"N 77°14'41.21"E
Corner-XII 28°36'40.37"N 77°14'41.71"E
Corner-XIII 28°36'40.14"N 77°14'44.39"E
The project envisages construction of Museum building. The building will have Open and
basement parking and 7003.91 m2 is to be developed as landscaped. The area details are given in
Table-3.
Table-3: Detailed Area Statement
S. No. Particulars Area in Sq.m.

1 Total Plot Area 26,299.00
2 Permissible Ground Coverage @ 35% of plot area 9,204.65
Permissible Additional Ground Coverage for Atrium @ 2629.90
3
10%
4 Achieved Ground Coverage @ 34.99% of plot area 9,202.7
5 Permissible FAR @ 1.2 of plot area 31,558.80
6 Proposed FAR@ 1.1998 of Plot area 31,553.90
7 Total Basement Area 14,471.88

8 Built Up Area (FAR + Basement) 46,025.78

9 Open Area (Plot Area – Achieved Ground Coverage) 17,096.30
10 Minimum Landscape area required @ 25% of open area 4,274.075
11 Landscape Area Proposed@ 37.35 % of open area 7,003.91
12 Height of the tallest tower 21 m
13 Paved Area 10,092.39
The Site Layout Plan is attached as Annexure-II.
4. DETAIL OF BUILDING BLOCK

Details of Building Blocks are given in Table 4.
Table 4: Details of Building Blocks

S. No. Type of building Story
1 Museum Building B+G+4
The building plans are attached as Annexure-III. The building plan approval has been exempted
by Central Public Works Department vide letter no. 7/ 10/2014-W-II/DG/Vol.II/501 dated
18.05.2016. The copy of letter is attached as Annexure-IV. The section and elevation plans are
attached as Annexure-V.
5. POPULATION DETAIL
Total population of the proposed project will be 6,970. Breakup of the population is given in
Table-5.
Table-5: Calculation of Population
Description Population
Auditorium population 200
Imax Theatre @ 1 person per 1.5 sqm 598
Convention centre @1 person per 1.5 sqm 466
Dormitories population @1 person per 7.5 sqm gross floor area ratio 26
Guest room (no. of rooms is 4) 8
Population of rental offices and other offices @ 1 person per 10 sqm
(fourh floor) 282
Staff population @ 1 person per 3 sqm 1824
visitors population area @ 1 person per 3 sqm 3566
Total 6970
*Source- National Building Code, 2005

6. ROAD & PARKING DETAILS

Internal Road – Project has 6 meters wide roads inside the premises.
External Road – Bharion Marg is just adjacent to project site towards North.
Setbacks – 12 meters wide setbacks have been provided in all around four direction of
project site.
Entry/exits provided in the project Premises –1 main entry and 1 main exit has been
provided in the East direction of project site.
Parking Details - The total parking required is 631 ECS, & proposed parking are 635 ECS is
provided in the basement and on surface.
The details of the Parking requirement are provided in the Table-6.
Table-6: Calculation of Parking Requirement
Parking
Description As Per Delhi Building Byelaws
(E.C.S.)
Parking For Museum: 2 ECS/100 sq.m of FAR 631

Required FAR of the Museum (31,553.5402 m2 )
Total ECS required 631
In Basement Area @ 1ECS/16m2
602
Basement Area (9632 m2)
Parking
Proposed In Open Area @ 1ECS/23 m2
Open Area (759 sq.m) 33
Total ECS provided 635
Basement parking plan is attached as Annexure-VI.
7. LANDSCAPE DEVELOPMENT
Increasing vegetation in the form of greenbelt is one of the preferred methods to mitigate air
pollution. Plants serve as a sink for pollutants, reduce the flow of dust and reduce noise
pollution. Calculation of green area for proposed project is given in Table-7. Table-8 indicates
various planned species to be used in greenbelt development.
Table-7: Calculation of Green Area
Total Plot area 26,299 m2
Required Landscape are required@ 25% of open area 4274.075 m2
Landscape are proposed@ 37.35% of plot area 7003.91 m2

Table-8: List of Species for Greenbelt Development along with Nos.

S. Crown Leaf
N Hindi Sensitive/ Heigh Crown Surface Area Area Stomata
o Binomial Name Family Common Name Name Tolerant t (M) Flowering Season Shape M2 CM2 l Index
Mimosea
1 Acacia dealbata Link e Silver Wattle Tolerant 15m April-June Oblong
Acacia nilotica (Linn) Mimosea Indian Gum-
2 Willd. e Arabic-tree Babul Tolerant 8m Aug-JAN. Spreading 8294 136 11
Albizia moluccana Mimosea Subabul, Tolerant
3 Mig e White popinae Vilaitibaral 15m July - Oct. Oblong
Alstonia scholaris Apocyna Tolerant
4 (linn.)R. Br. ceae Chattiyan 15m Dec - Mar. Round 241681 52 15
Tolerant March -July
Anona swuamosa Anonace extended up to
5 Linn. ae Custard apple Seetaphal 10m sept. Round 2178 54 26
Anona reticulata Anonace Luvuni, Tolerant
6 Linn. ae Bullock's Heart nona 10m June. Round 2017 51 17
Azadirachta indica A. Meliacea Tolerant Jan - March, Aug.
7 juss. e Indian Lilac Nim 20m - Sept. Spreading 300445 84 29
Balanites roxburghiji Balanitac Tolerant
8 planch eae Desert-date Hingan 9m April-June Spreading
Barringtonia Barringto Tolerant March-May, Sept-
9 acutangula (l)Gaertn niaceae Indian Oak Hijal 9-12m Oct. Spreading
Caesalpi Tolerant 10-
10 Cassia pumila Lamk naceae Yellow Cassia 12m Round 13274 118 20
Caesalpi Minjri Tolerant 10-
11 Cassia siamea Lamk naceae Iron wood tree (Beng.) 12m Aug - May Oblong 3927 138 21
Casuarina Caesalpi Australian or Tolerant Feb. -April, Sept-
12 equisetifolia Linn. naceae Whistling pine Jangli saru 10m OCT Oblong
Citrus aurantium Tolerant Round/
13 Linn Rutaceae Limbu 5m Sept - Nov Oblong 495 20 36
Clerodendrum inerme verbenac Tolerant
14 (Linn) Gaertn eae Vanjai 5m Nov - Jan Round 723 42 18
Derris indica Pongam-Oil Tolerant
15 (Lam.)Bennett. Fabaceae Tree, Karanj Karanja 10m April - June Round 6278 80 25
verbenac Tolerant Throughout the
16 Duranta repens L eae 3m year Spreading 60 63 22

S. Crown Leaf
Myrtacea Tolerant Feb. -April, Oct.-
17 Eucalyptus hybrid e Mysore gum 20m Dec. Conical 50047 50 13
Ficus benghalensis Moracea Tolerant
18 Linn e Banyan Tree Bargad 20m April - June Spreading 236494 119 22
Moracea Tolerant
19 Ficus benjamina Linn e Pakur 12m Sept - Nov Spreading 87326 29 19
Moracea Indian Rubber Tolerant Spreading/
20 Ficus elastica Roxb e Tree 12m Round 6028 94 19
Moracea Korotosani( Tolerant
21 Ficus gibbosa Blume e Orisa) 10m April - May Spreading 223,45.4 40 20
Moracea Tolerant Round/
22 Ficus religiosa Linn e Peepal Tree Pipal 20m Jan.- May. Oblong 1,44,868.7 114 19
Moracea Tolerant
23 Ficus virens Ait e Pilkhan 10m Jan.- May. Oblong 1,97,838.2 43 16
Tolerant April - Aug
Gardenia tasminoides Rubiacea Extended up to
24 Eills e 5m Sept. Oblong 266 58 19
Grevillea robusta A. Proteacea Silvery or Silky Tolerant
25 Cunn. e oak 20m Feb - April Oblong
Guazma ulmifolia Sterculia Tolerant Round/
26 Lamk ceae Rudraki 10m Mar - August. Spreading 30280 85 13
Heterophragma Bignonia Tolerant Round/
27 roxburghiji DC ceae 18m Feb. - April. Oblong 155218 35 14
Hibiscuc rosa- Malvacea Tolerant Throughout the Round
28 sinensis Linn e Jasud Jasum 3m year /Oblong 61 45 23
Rubiacea Tolerant Throughout the
29 Lxora coccinea L e Rangan 6m year Oblong 183 70 23
Tolerant More or Less
Rubiacea throughout the
30 Lxora Rosea e 6m year Oblong 296 62 20
Kigelia africana Bingnoni Tolerant Round/
31 Lamk aceae Sausage tree 10m Mar.- June Oblong 58432 268 13
Lagerstroemia Lythrace Queen crape Tolerant
32 speciosa (Linn) ae Myrte Jarool 10m April - June. Oblong 72569 88 14

S. Crown Leaf
Managifera indica Anacardi South India -Jan - Round /
33 Linn aceae The mango tree Am Sensitive 15m Mar Oblong 69005 85 31
Round /
34 Milletia pequensis Ali Fabaceae Tolerant 10m Aug. - Oct. Oblong 42312 167 12
Millingtonia hortensis Bignonia Indian cork- tree, Oblong /
35 L.F ceae Buch Sensitive 10m Oct.- Dec. Round 22439 139 18
Mimusops hexandra Sapotace Oblong /
36 Roxb. ae Khirni Tolerant 10m Sept - Nov Round 4063 89 20
Moracea
37 Morus alba Linn. e Tuti Tut Sensitive 8m Feb.- June Oblong 1048 285 17
Peltophorum Tolerant
pterocarpum Caesalpi Oblong /
38 (DC)Backer naceae Copper pod tree. May - Sept. Round 231045 371 17
Manila Tolerant
Pithecellobium ducle Mimosac tamarind,Madras
39 (Roxb.) Benth eae thorn Vilayatimili 8m Jan. - Feb. Oblong 2565 183 12
Prosopis chilensis Mimosac Vilayati Tolerant
40 (Molina)Stuntz eae Mesquite kikkar 10m Dec. - April. Spreading 7951 51 19
Prosopis cineraria Mimosac Tolerant
41 Linn. eae Khejri 12m Dec. - April. Spreading 13431 54 18
Psidium Guayava Myrtacea Tolerant
42 Linn. e Guava tree Amrud 5m Oblong 9243 54 28
Mimosac Tolerant Spreading
43 Samanea saman Jacq eae Rain Tree 20m Mar. - June. /Round 99306 283 16
Sapindus emarginatus Sapindac Tolerant Oblong /
44 Vihl eae Soapnut 10m Oct. - Dec. Round 43789 111 24
Saraca asoka Caesalpi Tolerant
45 Roxb.De Wilde naceae Ashok 5m Dec. - May Spreading 2295 69 18
Sesbania grandiflora Swamp- Ogosti(Oriy Tolerant
46 Pers Fabaceae pea,Agathi a) 10m Sept. - Dec. Oblong 4695 130 20
Sesbania sesban Tolerant
47 (Linn)Merrill Fabaceae Common Sesban Jainti 6m Aug. - Dec. Oblong 4564 118 19
Spathaodea Bingnoni Indian Tulip Tolerant Oblong/
48 campanulata Beauv aceae Tree 12m Nov. - Jan. Round 73250 89 25

S. Crown Leaf
Spondias pinnata Anacardi Tolerant
49 (L.f) aceae Tolerant 10m Feb - April Round 25587 131 23
Myrtacea Oblong/
50 Syzygium cumini Linn e Black plum Jaman Tolerant 20m Mar. - May. Spreading 112143 78 21
Tamarindus indica Caesalpi The Tamarind
51 Linn naceae Tree Imli Tolerant 20m April - Oct. Spreading 276840 129 18
Thespesia
populeneoides(Roxb) Malvacea
52 Kostel e Umbrella Tree Paraspipal Tolerant 10m Through the year Round 34635 184 30
Thuja occidentalis Cupressa American
53 Linn. ceae Arborvitae, White cedar Tolerant 15m Conical
Terma orientalis Ulmacea Gio Indian Throughout the Round/
54 Blume e CharcoalTree, nettle tree Tolerant 6m year Oblong 425734 66 27
Zizyphus mauritiana Rhamnac
55 Var. Fruticosa eae Indian Jujube Ber Tolerant 10m April -Oct. Round 2638 24 12
Source: Guidelines for development of greenbelt CPCB-2007
Landscape Area is shown in Site Plan attached as Annexure-II.

8. WATER REQUIREMENT, SUPPLY AND DISTRIBUTION

Water Requirement for the proposed project is discussed below.
8.1 Water requirement during Construction phase

Water requirement during the Construction phase will be met by private water tanker.
8.2 Water requirement during operation phase

Water requirement during the operational phase will be met through Delhi Jal Board.
includes fresh water requirement, flushing, landscaping, DG cooling. The total fresh water
requirement is 138 KLD. The water requirement for Flushing, DG cooling and landscaping will
be met through treated water from STP.
Details of break-up of water requirement are given in Table-9.
Table 9: Details of Water Requirement
Unit water
Area in Total
water requiremen Flushing Total
S. Sq.m. / water
Description consumpt t for water Wastewat
No. Populati required
ion domestic (kld) er (kld)
on (kld)
(litres) use (kld)
Visitors population
+Auditorium population +
4830 15 72.45 43.470 28.980 63.756
Imax Theatre + Convention
1 Centre Population
Staff population +
Dormitories population + 1858 45 83.61 55.740 27.870 72.462
2 Guest room
Population of rental offices
282 45 12.69 8.460 4.230 10.998
3 and other offices
Kitchen & Pantry.
Restaurant Kitchen, Food ….. 30 30.000 ….. 18.000
4 Court
7003.91 5 litr per
35.02 …. ….. ….
5 Horticulture Sqm sqm
1
3030.00 ltr/KVA/h 18.18 ….. ….. ….
6 DG Sets r
11.5
412.00 113.71 ….. ….. ….
7 HVAC lt./ton/hr.
1% of
total water
requireme
8 Fire fighting nt 3.66 …. …. ….
TOTAL 369.32 137.670 61.080 165.216
Say 370 Say 138 Say 61 Say 165

8.3 Wastewater Generation

The total estimated quantity of wastewater to be generated from proposed project is 165 KLD.
Calculation of wastewater generation is shown below in Table-10.
Table-10: Calculation of Wastewater Generation
Details Water (KLD)

Water requirement for domestic purpose 108
Wastewater to be generated from domestic use (@ 80% of domestic 86
water requirement)
Water Requirement for kitchen purpose 30
Wastewater to be generated from kitchen use (@60%) 18

Water requirement for Flushing Purpose 61
Wastewater to be generated from Flushing (@ 100% of flushing 61
requirement)
Total Wastewater generated 86+18+61 = 165 KLD
Water balance diagram for Non-Monsoon is given in Figure-4 and for Monsoon is given in
Figure-5.

One time water

Requirtment=
370

time) = 4 138 35
Landscaping = 35

96

18
All Figures in KLD
= 86+18+61= 165
Fresh Water Requirement

STP capacity 20% more than
Wastewater Generation total wastewater generation = Recycled water
Treated Water 200 @80% = 132
but we provided approx 320
Recirculated condensate KLD STP at site for safer side
Water
Figure-4: Water Balance Diagram for Non-Monsoon Season

One time water

Requirtment=
370

time) = 4 138 15
Landscaping = 15

96

All Figures in KLD

18

= 86+18+61= 165
Fresh Water Requirement Discharge to sewer

Wastewater Generation = 20
Treated Water STP capacity 20% more than

total wastewater generation = Recycled water
Recirculated condensate 200 @80% = 132
Water but we provided approx 320
KLD STP at site for safer side
Figure-5: Water Balance Diagram for Monsoon Season

Reuse of Treated Water:
Total waste water generated is 165 KLD, which will be treated in the STP of capacity higher
than the waste water generated i.e. 320 KLD. The treated water available is 132 KLD (@ of
80%) and it will be recycled and re-used for flushing, DG Cooling and landscaping. During the
non-monsoon season, treated water will be used in Flushing, DG Cooling & landscaping. The
details of recycled water uses are provided in Table-11 below.
Table-11 Recycled Water Uses

Treated DG HVAC Discharge to
Flushing Landscaping
Water Cooling sewer
Non-Monsoon 18 KLD
132 KLD 61 KLD 35 KLD 20 KLD 0
Season
Monsoon Season 132 KLD 61 KLD 15 KLD 20 KLD 18 KLD 20 KLD
Wastewater Treatment Scheme

The waste water generated will be treated in the Sewage Treatment Plant, and the capacity of
Sewage Treatment Plant (STP) will be higher of waste water generated i.e. 320 KLD. The
proposed STP is based on Fluidized Bed Reactor (FBR).
9. STORM WATER DRAINAGE

The storm water disposal system for the premises shall be self-sufficient to avoid any collection/
stagnation and flooding of water. Maximum harvesting will be done within the site. Therefore, it
has been decided to provide sufficient rain water harvesting at selected locations, which are
liable to catch the maximum run-off from the area. Following are some measures for Storm
water disposal:
1) Since the existing topography is congenial to surface disposal, a network of storm water
pipe drains is planned adjacent to roads. All building roof water will be brought down
through rain water pipes.
2) Proposed storm water system consists of pipe drain and catch basins at regular intervals
for rain water harvesting.
3) The annual rainfall intensity of 11 mm/hr shall be considered for designing the storm
water drainage system.
4) The entire site is provided with extensive planned underground drainage system with
gravity connections to the RWH structures. The arrangement provides appropriate
protection to the site against flooding.

10. RAINWATER HARVESTING

Rainwater harvesting is the activity of direct collection of rainwater. Collected Rainwater will be
stored for direct use. Rain Water Harvesting is the technique through which rain water is
captured from the roof and paved surfaces and stored in sub-surface reservoir.
Advantages:
 To meet the ever increasing demand for water.
 To avoid flooding of roads.
 To reduce ground water pollution.
 To reduce the soil erosion.
 To supplement domestic water requirement during summer, drought etc.
Rainwater Harvesting Calculation for the proposed project is given in Table-12 and Table-13.
Table-12: Runoff Calculation of the Area
Intensity of Intensity of Runoff

Type of Catchment Runoff Runoff
S. No. Rainfall Rainfall (In 15
Surface Area (m2) Coefficient (m3 /hr)
(mm/hr) (m/hr) minutes)
1. Roof Area 9202.7 0.8 11 0.011 80.98 20.24
2. Green Area 7003.91 0.2 11 0.011 15.41 3.85
3. Paved Area 10092.39 0.7 11 0.011 83.26 20.82
Total Runoff (m3 /hr) 179.65 44.91
Table-13: Numbers of Pits Calculation

Runoff in No. of No. of
S. No. Diameter of the Depth of the Volume of
15 minutes structures structures
structure (m) structure (m) the Pit(m3)
(m3) required proposed
1. 4 3 37.68 44.91 1.19 5
As per the calculation provided above, the nos. of RWH structure is required 1.19 and we are
proposing 5 nos. of RWH structures.

11. POWER REQUIREMENT

The total electrical load demand has been estimated to be 2430 KW. The source of power will be
supplied by BSES Rajdhani Power Limited.
power back-up for the essential load. The DG sets will be of water cooled.
12. SOLID WASTE GENERATION AND MANAGEMENT

The project will adopt a systematic approach for solid waste collection and disposal. Solid waste
generated from the project will be collected properly and will be managed as per MSW Rules,
2000.
The domestic solid waste will be generated by the occupants of the Residential Apartments,
Visitors, Community Population, pertains to the two categories, Bio-degradable and Non-
biodegradable. These solid wastes will be collected separately by putting three types of separate
bins at the source of generation. For the biodegradable waste green bins will be provided, for the
recyclable waste blue bins and for the non-recyclable waste dark grey bins will be provided.
Biodegradable waste will be subjected to composting by Organic waste converter and compost
will be used as manure. It is estimated that maximum solid waste generation would be about
1687.5 kg / day, and 120.28 kg of sludge (wet basis). Following are the solid waste generation
rate has been considered as given in Table-14.
Table-14: Proposed Solid Waste Generation Rate

Total
S. Waste
Waste Generation Formul Popu
N Category of Solid Waste Genera
Rate a latio
o. ted
n
Visitors population +Auditorium Total
1 population + Imax Theatre + 0.1 to 0.2 kg/cap/day Populati 4830 724.5
Convention centre Population on*0.15
Staff population + Dormitories Total
2 population + Guest room + Population 0.3 to 0.6 kg/cap/day Populati 2140 963
of rental offices and other offices on*0.45
1687.5
Total kg/day
* Source: Manual on Municipal Solid Waste Management, published by Central Public Health and
Environmental Engineering Organization (CPHEEO), Ministry of Urban Development, Government of India.

The E-waste generated will be managed as per the E-waste management and handling rules
2016.
The detailed Solid Waste Generation Management Plan is provided in Figure-7 below:
Waste
Organic Waste: Inorganic waste: E -waste: Electronic waste:

-CFL Lamps
-Waste from -Plastic waste -Information - Fluorescent tubes
cafeteria. - Metal waste. technology and
-Waste from green belt - W aste from street The Hazardous telecommunication As per CPCB Guideline
and landscape sweeping Wastes (Management, H equipments for Environmentally
Municipal Solid Wastes -Municipal Solid Wastes andling and - Consumer Sound Mercury
(Management and (Management and Transboundary electrical and Management in
Handling) Rules, 2016 Handling) Rules, 2000 Movement) Rules ,2008 electronics Fluroscent Lamp Sector
Disposed by Will be disposed off Will be disposed through Will be disposed Will be disposed
Organic waste through private waste Recylcerauthorized by through recyclers through recyclers
Converter to collecting vendors after Central Pollution Control authorized by authorized by
produce manure. temporary storage at Board. On each disposal Central Pollution Central Pollution
site. Temporary storage , Form 13 will be control Board. control Board.
to be enabled through a maintained and returns Records will be Records will be
2 m x 2 m x 1m blue will be filled to the maintained for the maintained for the
colored bin. Pollution Control Board e-waste generated e-waste generated
through Form 2 as through Form 2 as
Infrastructure required: Infrastructure required: per the E -Waste per the E -Waste
1) Trolleys – 5 1) 2 x 200 liter barrel (Management and (Management and
2) Blue Bins – 2 with proper marking Handling Rules) Handling Rules)
2) Secondary 2011. 2011.
containment in
basement
Figure-7: Solid Waste Management Plan
13. FIRE FIGHTING SYSTEM

The Fire Fighting will be designed as per the recommendations of the National Building Code of
India : Part 4 F ire and Life safety: 1997 T he building has been classified under Group-A :
Residential Building, Sub Division Apartment Housing (A-4) in the National Building Code
2005.The firefighting system has been designed considering the following codes, manual and
guidelines;
• National Building Code of India (NBC);
• As per requirement of fire officer/local fire approving authorities; and

• As per Indian Standard Code for Fire Protection (IS Codes)
14. DETAIL OF CONSTRUCTION MATERIAL

List of building materials being used at site:
1. Coarse sand
2. Fine sand
3. Stone aggregate
4. Stone for masonry work
5. Cement
6. Reinforcement steel
7. Plywood & steel shuttering
8. Pipe scaffolding (cup lock system)
9. Bricks
10. Tiles
11. P.P.V.C. conduit
12. MCBs/DBs
13. PVC overhead water tanks
14. Wastewater lines
15. S.W. sewer line up to main sewer
16. PVC rain water down take
17. Stainless steel sink in kitchen
List of Machinery to be used during Construction is as follows:

1. Dumper : Shall be used for mud and material handling
2. Concrete mixer with hopper : for RCC work
3. JCB/Pock line : Shall be used for digging and earth work
4. Concrete Batching Plant : Will be used for concrete mixing
5. Road roller : For compacting the earth

Annexure-I
Land Allotment Letter
Annexure-II
Site Plan
AREA STATEMENT
AREA CHART AREA UNITS
PLOT AREA 26299 SQ.MT.

FAR
PERMISSIBLE FAR 120
PERMISSIBLE BUILT UP AREA 31558.8 SQ.MT.
GROUND COVERAGE
PERMISSIBLE GROUND COVERAGE 35 PERCENT
PERMISSIBLE AREA ON GROUND FLOOR 9204.65 SQ.MT.
PERMISSIBLE ADDITIONAL GROUND
COVERAGE FOR ATRIUM @ 10% 2629.9 SQ.MT.
SET BACKS
FRONT 15 MT.
REAR 12 MT.
SIDE 12 MT.
PROPOSED BUILT UP AREA

BASEMENT 14471.88 SQ.MT.
GROUND FLOOR 9202.7 SQ.MT.
FIRST FLOOR 6720.56 SQ.MT.
SECOND FLOOR 7914.4 SQ.MT.
THIRD FLOOR 3112.8 SQ.MT.
FOURTH FLOOR 3973.75 SQ.MT.
ATRIUM (@ 25% OF 2518.76 SQMT) 629.69 SQ.MT.
TOTAL BUILT UP AREA(EXCLUDING

31553.9 SQ.MT.
BASEMENT)
TOTAL BUILT UP AREA (INCLUDING
46025.78 SQ.MT.
BASEMENT)
FAR ACHIEVED 119.98
GROUND COVERAGE ACHIEVED 34.99 PERCENT
PARKING PROVISIONS
ECS REQUIRED@2 ECS/100 SQMT.OF BUA 631.08 ECS

SAY 631 ECS
PARKING PROVIDED ECS
BASEMENT 2X301 (DOUBLE STACK) 602 ECS
SURFACE 33 ECS
TOTAL PARKING 635 ECS
Annexure-III
Building Floor Plans
Annexure-IV
CPWD letter of exemption from
Building plans approval
Annexure-V
Section and elevation plan
Annexure-VI
Basement Parking Plan
Annexure-VII
Topographical Survey Plan
Annexure-VIII
Environmental Monitoring
Report
Annexure-IX
Firefighting schematic plan
Annexure-X
Risk Assessment Report
DISASTER MANAGEMENT PLAN
The Proposed project encompasses the lives of a large number of people. It also involves
installation of various structures and machineries that meet the comfort and needs of its
population but may also pose serious threat to the occupants in case of an accident. It is thus
considered necessary to carry out a risk assessment and disaster management plan for the project.
Type of Emergency, External and Internal Origin of Hazards

It is attempted to plan and construct the buildings following all safety norms. However, it is not
always possible to totally eliminate such eventualities and random failures of equipment or
human errors. An essential part of major hazard control has therefore, to be concerned with
mitigating the effects of such emergency and restoration of normalcy at the earliest. A detailed
Table showing activities during construction and operation phase along with mitigation measures
are given in Table below:.
Activities during Construction and Operation along with Mitigation Measures
Hazards Associated with Activities Control / Mitigation Measures

Manual Handling Exercise/ warm up-get help when needed-
Strains and sprains - incorrect lifting - too control loads-rest breaks/ no e xhaustion-
heavy loads -twisting - bending - no rapid movement/ twisting/
repetitive movement - body vibration. bending/repetitive movement - good
housekeeping.
Falls - Slips - Trips Housekeeping - tidy workplace -
Falls on same level - falls to surfaces guardrails, handholds, harnesses, hole
below - poor housekeeping- slippery cover, hoarding, no slippery floors/trip
surfaces uneven surfaces -poor access to hazards - clear/ safe access to work areas-
work areas climbing on and off plant- egress from work areas - dust/water
unloading materials into excavations wind controlled - PPE.
- falling objects.
Fire Combustible/ flammable materials
Flammable liquids/Gases like LPG, properly stored / used -good
Diesel Storage area and combustible housekeeping-fire extinguishers made
building materials - poor housekeeping - available & Fire hydrant Network with
grinding sparks - open flames, absence of reserve Fire water (As per NFPA Code) -
Fire hydrant net work. Emergency Plan in case of Fire or collapse
of structure.
Absence of Personal Protective Head / face- footwear- hearing / eye-skin-
Equipment respiratory protection provided - training-
maintenance.
Lack of adequate footwear- head
protection hearing/ eye protection -
respiratory protection-gloves-goggles.
Defective or wrong Hand Tools Right tool for the job - used properly -
Wrong tool - defective tool - struck by good condition/ maintenance guards-
flying debris- caught in or on -missing isolation- eye/ face protection - flying
guards -carbon monoxide - strains and debris controlled.
sprains - dust.
Electricity Leads good condition and earthed - no
Electrocution – overhead / underground temporary repairs - no exposed wires-
services - any leads damaged or poorly good insulation-no overloading - use of
insulated- temporary repairs -no testing protective devices - testing and tagging -
and tagging-circuits overloaded-non use no overhead/ underground services
of protective devices.
Scaffolding All scaffolds correctly braced and
Poor foundation-lack of ladder access stabilized - 3:1 height to base ratio - firm
insufficient planking-lack of guardrails foundation, plumb and level - ladder
and toe boards-insufficient ties or other access provided and used - proper
means-all scaffolds incorrectly braced or platform (3 planks/ 675 mm) - planks
stabilised to prevent overturning. secured- guardrails and toe boards – 900
mm to 1100mm high, within 200 mm of
working face, mid - rail.
Ladders Secured against movement or footed -
Carrying loads - not secured against ladders in good condition - regularly
dislodgement - defective ladders– not inspected - extend 1m above platform -
sufficient length- wrong positions - 4:1 angle - out of access ways, vehicle
incorrectly placed (angles, in access movements - climbing - no carrying loads
ways, vehicle movements. - 3 points of contact - no higher than 3rd
step down - use for access only, not
working platforms.
Excavations Soil stability known-no water
Trench collapse - material falling in accumulation- existing services known -
undetected underground services-falls- material 600 mm from edge - clear of
hazardous atmosphere struck by traffic suspended loads-hardhats/ PPE- ladders -
and mobile plant. public protection - atmospheric testing-
traffic controls - Emergency Plan.
Gas Cutting and Welding Welding flash and burns controlled with
Fire-welding flash, burns, fumes, PPE and shields -fumes controlled with
electrocution in wet conditions- ventilation and PPE (in good condition
flashback in oxygen set, leaking and properly positioned),Gas cylinders be
cylinders, acetylene cylinders lying kept upright & secured position (properly
down-poorly maintained leads. tied) - combustible materials to be kept at
secured place to avoid fire & Fire
Extinguishers to be kept in fire prone area
with training to people for its use.
Noise Levels below 85 decibels - proper
Unknown noise levels - known noise protection.
levels over 85 decibels
Falling Material Materials to be secured-kept away from
Fall during carrying/ Lifting materials- edge- toe boards -Use of hard hats.
dislodged tools and materials from
overhead work areas.
Craneage& Lifts Periodic testing by competent authority-
Display of carrying capacity i.e load (No. correctly slung/ secured loads, lifting
of person) incorrectly slung, defective equipment good condition-use of proper
lifting equipment, unsecured loads, hand signals - falls while unloading
craning in close proximity to building controlled.
people and plant- falls-falling materials.
Visitors Presence at site Sufficient hoarding - fencing and
Falls -struck by - dropped materials-road barricades-safe pedestrian access past site
accidents -insufficient hoarding or traffic management for loading and
fencing-pedestrian access past site- delivery- construction separated from
mechanical plant movement on a nd off occupied areas of projects
site
Emergency Response Plan (ERP)
The overall objective of an Emergency Response Plan (ERP) is to make use of the combined
resources at the site and outside services to achieve the following:
• To localize the emergency and if possible eliminate it;
• To minimize the effects of the accident on people and property;
• Effect the rescue and medical treatment of casualties;
• Safeguard other people;
• Evacuate people to safe areas;
• Informing and collaborating with statutory authorities;
• Initially contain and ultimately bring the incident under control;
• Preserve relevant records and equipment for the subsequent enquiry into the cause and
circumstances of the emergency;
• Investigating and taking steps to prevent reoccurrence.
The ERP is therefore related to identification of sources from which hazards can arise and the
maximum credible loss scenario that can take place in the concerned area. The plan takes into
account the maximum credible loss scenario-actions that can successfully mitigate the effects of
losses/ emergency need to be well planned so that they would require less effort and resources to
control and terminate emergencies, should the same occur.
Standards and codes used in building construction to minimize the risk of natural calamities like
wind load, seismic load (earthquake), thunder storm/ lightning etc, as per NBC 2005 are given
below:
Design Standards
• IS: 456-2000 - Code of Practice for Plain and Reinforced Concrete
• IS: 875 (Part 1 to 5)-1987 - Code of Practice for Design Loads (Other Than Earthquake)
for Buildings and Structures.
o Part-1 Dead Loads- Unit Weights of Building Materials and Stored Materials
o Part-2 Imposed Load
o Part-3 Wind Loads
o Part-4 Snow Loads (Not releventin this case)
o Part-5 Special Loads and Combinations
• IS: 1893 (Part1)-2002 - Criteria for Earthquake Resistant Design of Structures
• IS: 4326- Earthquake resistant design and construction of building
• IS: 13920-1993-Code of Practice for Ductile Detailing of Reinforced Concrete Structures
subjected to Seismic Forces
• IS: 3370 (Part I, II & IV)- 1965: Code of practice for concrete structure for the storage of
liquids
• IS: 2950 (Part I) Code of practice for design and construction of raft foundations
• IS: 1904- Code of practice for design and construction of foundations in soils
• IS: 800-2007–General construction in steel-code of practice.
Main hazards identified for the project include hazards pertaining to fires in buildings and fire in
diesel storage areas, earthquake and LPG leakage and an ERP pertaining to these is described in
the following section.
Response in case of Earthquake
Response Procedures for Occupants

If indoors:
• Take cover under a piece of heavy furniture or against an inside wall and hold on.
• Stay inside: The most dangerous thing to do during the shaking of an earthquake is to try
to leave the building because objects can fall on you.
If outdoors:
Move into the open, away from buildings, streetlights, and utility wires. Once in the open, stay
there until the shaking stops.
If in a moving vehicle:
Stop quickly and stay in the vehicle. Move to a clear area away from buildings, trees, overpasses,
or utility wires. Once the shaking has stopped, proceed with caution. A void bridges or ramps
that might have been damaged by the quake.
After the quake
• After the quake be prepared for aftershocks.
• Although smaller than the main shock, aftershocks cause additional damage and may
bring weakened structures down. Aftershocks can occur in the first hours, days, weeks, or
even months after the quake.
Help injured or trapped persons.
• Give first aid where appropriate. Do not move seriously injured persons unless they
are in immediate danger of further injury. Call for help.
• Remember to help those who may require special assistance--infants, the elderly, and
people with disabilities.
• Use the telephone only for emergency calls.
Response Procedure for emergency team
• Formulate an emergency response team for earthquake response. Using the public
address system, inform residents of response procedures discussed above.
• Inform the necessary authorities for aid.
• Ensure no person is stuck beneath any debris, in case of a structural failure.
• Ensure that all occupants standing outside near the buildings are taken to open areas.
• Ensure that the first-aid ambulance and fire tender vehicles are summoned if
necessary.
• Inform the nearby hospitals if there are any injuries.
• Check the utilities and storage tanks for any damage.
Response in case of LPG Leakage
• The affected area should be evacuated and cordoned off immediately

• Initiate an Emergency Response Team for LPG leakage.
• Shut down the main valves in the gas bank.
• Ensure that only concerned personnel are present in the affected area and all other
personnel and visitors are moved to the nearest assembly points.
• Rescue trapped personnel, also check if any personnel are unconscious in the area and
immediately move them outside and provide first aid. Ambulance should be summoned
to take injured personnel to the nearest hospital.
• Personnel in the nearby buildings to close all doors and windows to prevent entry of the
leaked gas.
• Source of leakage to be traced and isolated from all the other areas and if required use
pedestal fans to bring down the gas concentration.
• In case of a fire follow the instructions in case of fire.
Response in case of Fire

• Required response during in the event of a fire should be described in signs located in the
lobby.
• On sighting a fire, it should be immediately informed to the environment manager giving
the exact location and type of fire in detail.
• Initiate the Emergency Response Team for fires.
• If the fire is small, engage in extinguishing the fire using the nearest fire extinguisher.
• Guide the Emergency Response Team staff to the emergency assembly point.
• The Emergency Response Team should immediately inform the nearest dispensary and
security force. If required a fire tender should be summoned.
• The response team should immediately move to the point of fire and take all necessary
steps to stop the fire. If the fire is not controllable and spreads then the manager in charge
should inform the district authorities and call for external help.
• The Emergency Response Team will provide immediate relief to the injured residents at
the scene of incident. Any injured persons should be evacuated on priority to the
dispensary or one of the nearest hospitals based on their condition.
General Instructions for Occupants in case of Fire
• Get out of buildings as quickly and as safely as possible.
• Use the stairs to escape. When evacuating, stay low to the ground.
• If possible, cover mouth with a cloth to avoid inhaling smoke and gases.
• Close doors in each room after escaping to delay the spread of the fire.
• If in a room with a closed door.
• If smoke is pouring in around bottom of the door or if it feels hot, keep the doorclosed
• Open a window to escape or for fresh air while awaiting rescue.
• If there is no smoke at bottom or top and the door is not hot, then open the door slowly
• If there is too much smoke or fire in the hall, slam the door shut.
• Check that all wiring and utilities are safe.
Fire fighting system is proposed to prevent and control fire outbreaks for the project. The fire
fighting system will consist of portable fire extinguishers, hose reel, wet riser, yard hydrant,
automatic sprinkler system, and manual fire alarm system. The project will also be provided with
automatic fire detection and alarm system.

PDF of Proposed Museum Project

Uploaded by

Copyright:

Available Formats

PDF of Proposed Museum Project

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

PDF of Proposed Museum Project

Uploaded by

Copyright:

Available Formats

Proposed Museum Project

Form-1, Form -1A & Conceptual Plan,

Ascenso Management & Consulting Services Pvt. Ltd.

11. Nearest Town, City, District District Headquarters- New Delhi.

Consultant-Ascenso Enviro Pvt. Ltd. Page 1 of 17

15. Address for correspondence:

Designation(Owner/Partner/CEO) Executive Engineer

Address CED-1, CCU, MoEF&CC, Room No. 722,

18. Whether separate application of

20. If no, reason Not Applicable

21. Whether the proposal involves

22. Whether there is any Government Not applicable

Consultant-Ascenso Enviro Pvt. Ltd. Page 2 of 17

During the construction phase, land cover

Consultant-Ascenso Enviro Pvt. Ltd. Page 3 of 17

No Construction work has been started

Consultant-Ascenso Enviro Pvt. Ltd. Page 4 of 17

Consultant-Ascenso Enviro Pvt. Ltd. Page 5 of 17

The biodegradable waste will be collected

2.)Details regarding the Disposal and

Consultant-Ascenso Enviro Pvt. Ltd. Page 6 of 17

Bhairon Marg just adjacent to proposed

operation or decommissioning? Precautions will be taken to reduce the

1.30 Loss of native species or genetic

2. Use of Natural resources for construction or operation of the Project (such as

S. No. Information/ Checklist Yes/No Details thereof (with approximate

Source of water would be municipal water

Consultant-Ascenso Enviro Pvt. Ltd. Page 9 of 17

3. Use, storage, transport, handling or production of substances or materials, which

3.1 Use of substances or materials, No There will be no us e of the substances or

4. Production of solid wastes during construction or operation or operation or

S. No. Information/Checklist Yes/No Details thereof (With approximate

Consultant-Ascenso Enviro Pvt. Ltd. Page 10 of 17

Suitable management practice will be

There are two structures on the site which

Consultant-Ascenso Enviro Pvt. Ltd. Page 11 of 17

4.10 Agricultural wastes No Negligible waste will be generated from

5. Release of pollutant or any hazardous, toxic or noxious substances to air (kg/hr)

Sewage generated from labours shed and

The impacts are localized in nature and

Consultant-Ascenso Enviro Pvt. Ltd. Page 12 of 17

6. Generation of Noise and Vibration, and Emissions of Light and Heat:

S. No. Information/Checklist Yes/No Details thereof (with approximate

7.5 Is there a risk of long term build No There is no such risk.

During construction, all the labourers

An agreement will be signed with the

contractor, which will clearly deal with

9. Factors which should be considered (such as consequential development) which could

S. No. Information/Checklist Yes/No Details thereof (with approximate

• Housing development No Not applicable

9.4 Have cumulative effects due to No As it is planned development by the

(III) Environment Sensitivity

Consultant-Ascenso Enviro Pvt. Ltd. Page 16 of 17

9. Areas occupied by sensitive List of Schools:

(IV) Proposed Terms of Reference for EIA studies – Not Applicable

Consultant-Ascenso Enviro Pvt. Ltd. Page 17 of 17

Figure-1: Perspective View of Project

Consultant-Ascenso Enviro Pvt. Ltd. Page 1 of 66

 Latitude 28° 36' 39.57"N