3G KPI Optimization Sheet Nokia

Jump/Network Operations Portal NOP (intranet)
–Includes counters, KPIs and also reports in Reporting Suite

–http://nop-i.nokia.com/docs/jump.htm
•Almost all data has to be analysed at WCELL or WBTS level for the worst cells -> Evaluation over time
–Cell Availability
–Failures due to Radio, BTS or transport
–Handover Performance
–Traffic
–Cell Resources
–Iub Signalling
•Some data is better analysed at RNC level->Here only the time evolution and RNC comparison is usefu
–Failures due the RNC, Iu, Iur
–Iur, Iu, Relocation Signalling
Monitor Cell/Neighbour cells Availability - missing cell has impact to neighbouring cells performance also
1. Assess weekly average PLMN KPI performance to identify KPIs below targets
–Start from bigger picture assessment (PLNM -> RNC -> Cluster -> WCEL )
–Weekly average will smooth the performance and gives better accuracy of performance
2. Assess network performance at RNC/Area level to check if bad performance happens across
–Compare different RNC/Regions Performance
3. Apply drill down approach to assess bad performing KPIs in WCEL level
–Identify the failure call phases
–Categorizing failure ratio or distribution of each counters (Radio, transmission, BTS, RN
–Identify main cause of underperforming KPI’s
4. Prioritize analysis
–Filter using high number of failures or high number failure ratio (weighting)
–Identify top 20/50 worst cells
5. Analyze failure distribution in the network topology (rural, RNC border, expressway)
6. Propose Solution for cells having network KPIs below KPI targets
Because of the large number of cells in the network, it is not feasible to analyse all the cells.
Good methodology is to list top 10-20 worst cells per region and to build and follow an action plan on those
•This required a part-time or dedicated tracking role
Either total number of failures or failure rate (%) could be used
•Coverage hole, missing neighbour or capacity problem
In Loaded networks the Weekly Busy Hour CSSR is relevant

• The failures originate mostly from congestions (Iub, BTS HW (CEs), radio)
• The call blocking probability is designed for the BH
In Unloaded networks the Weekly Busy Hour CSSR may not yield the hour with highest blocking as NRT traf
In cell level it is needed to compute BH statistic based on absolute time period (e.g. 16-18h every day)
Typically CS and PS busy hours does not exist in the same time
•In example below, the PS Busy Hour is later in the evening (20-21 hours) than CS (15-16 hours).
During weekend CS data drops significantly while PS data is quite constant
The new smart phones such as Blackberry (RIM), iPhone (Apple) and N97 (Nokia) are loading the network in a new
•Applications which require ‘always on’ connectivity have become very popular in many networks
Fast dormancy or Quick Release will have impact to the load & performance
Call can be traced by using subscriber's IMSI, MSISDN or equipment’s IMEI number
Subscriber trace can be used for:
In system testing and provisioning phase for trouble shooting and network optimisation.
Jump User Id:
Jump password:
mparison between large areas (Cities, RNCs) is still required
ment as daily performance varies a lot especially in unloaded network, gives more accurate picture of KPIs.
or only particular RNC/Area
aken in the account as well as RT traffic
1.1.1.1.1. Accessibility Analysis (CS/PS/HS)
CS/PS Access Failure Optimization: Call Setup analysis
Call Setup Success Rate (CSSR)

CSSR is essentially •RRC Setup & Access Success * RAB Setup & Access Success
Poor CSSR could be a result of
•Poor coverage or dominance or interference issues in Radio interface
•Capacity issues in Radio or Iub interface
•Configuration issues in WBTS (parameters or HW)
Voice Access failure= RRC Setup & Access fails + RAB Setup & Access fails
Starting criteria for setup failure analysis
1) Site Ok?-- Cell Availability(Cell level report-RSRAN001), Alarms/HW Issues
2) Coverage or Interference-- Cell Power Report

a) Coverage-- best server RSCP should not be lesser than -102dbm----- Coverage Optimiza
b) Interference-- best server Ec/No should not be less than -12db
Tilt- for Dominance Optimization
Missing neighbor checks-- for neighbor optimization
3) AICH ACK. Received?----No (UL Coverage & RACH parameter Optimization)

4) RRC Connection Setup Received?
NO---a) RRC Setup reject msg. received---No (Check failure Cause)
Yes (AC Optimization--- check PRx Noise & Interferer Around BT
RRC Setup fails occurs (due to HC, AC, BTS, frozen BTS, Transp, Iub AAl2 fails, RNC, RNTI &
RRC_CONN_STP_FAIL_HC (very Minor)--- usually 0%
RRC_CONN_STP_FAIL_AC (dominant)
•Check UL Interference (R99 Noise Rise, RTWP- Cell Power Report), DL Power (HSDPA, R99 power) & Code o
•UL Power Spikes -> Disable UL Admission Control to if the number of failures is critical (PrxTarget-> 30 dB), imple
RRC_CONN_STP_FAIL_BTS (dominant when HSDPA active)

•Check BTS configuration in terms of CE allocation – Use Channel Element (M5001) Counters in order to evalu
•Evaluate NBAP counters (radio link reconfiguration failures)-- NBAP Signalling Per cause Report
•Expand the Capacity or decrease the traffic offered to the site--- Check Uplink CE Usage(should not be >8
•Frozen BTS/BTS not responding-- delete and re-create COCO/Site Reset
RRC_CONN_STP_FAIL_TRANS
•Evaluate Number of reconfiguration failure due the transmission-- Traffic_on_Physical_Medium_Sub-Layer & I
•Expand the capacity or decrease the traffic offered to the site
For ATM based Iub
•Check COCO Configuration
•Use AAL2 Multiplexing in case of two WAM
For IP based Iub---•Check IP based route parameters (ZQRL;)/ IP_Route_Resource_Reservations Report
DCH Reconfiguration failures due to AC/BTS/Trans-- NRT_DCH_Allocations_Statistics report

SHO Branch setup fails BTS/Iub-- SHO Overhead Report--No. 88, traffic
RNC capacity SW New DSP counters-- DSP Resource Usage, DSP State Changes- System reset/user reset &
RRC_CONN_STP_FAIL_RNC
•Typically RNC fault or Incoming SRNC Relocation Failure (inter-RNC border)--- RNSAP/NBAP Signalling
•Iur Troubleshooting-- RNSAP_Signalling Report
•DMPG problem in RNC
•Required ICSU log tracing if no RNC fault or SRNC relocation problem
RRC_CONN_STP_FAIL_ICSU_OVERL
•ICSU overload
RRC_CONN_STP_FAIL_RNTI ALLO FAIL

• RNC decides to reject RRC connection request due to RNTI allocation failure caused by RRMU overload
YES---RRC Connection Setup complete msg. sent from UE?---No (L1 Synchronization Fail/ RN
YES ( RRC Active fails
b)
c)
RRC Access failure reasons: RRC Active release can be due t
RRC_CONN_ACC_FAIL_RADIO (Dominant failure cause type)
• Perform drive test to detect if UL or DL coverage Coverage or interference-- C
–UL Coverage
§UL coverage(TMA/MHA chk), Interference-- Tilt / Missing Neighbor chk / best serve
–DL Coverage
§Tune SCCPCH Power if UE does not receive the RRC Setup Message from RNC./ Ante
/ Coverage Optimization-- PRACH_Propagation_Delay Report
• If UE does not synchronize(L1)
–tune CPICHToRefRABOffset vs.Qqualmin (or Qrxlevmin)
–Due to Increased interference with HSDPA, this max radio link power for AMR (offset parameter) has
RRC_CONN_ACC_FAIL_MS
–UL Coverage
§Tune Cell Dominance (or CPICH) in order to balance UL and DL (if UL interference is
If RRC setup/access failure due to Radio/MS, it is also possible to check whether UEs are located at distance area or close
•Propagation delay counters from RRC measurement M1006C128-C148 reports call setup distance during RRC
•This give hints that either cells has large coverage area (tall sites with over-shooting) or non-optimum cell coverag
Some more counters of RRC Access fails

•M1006C203 RRC CONN REJECT DUE TO IUB OVERLOAD CTRL
•M1006C204 RRC CONN REJECT DUE TO MAX REGISTRATIONS
•M1006C205 RRC CONN REJECT DUE TO CENTRALIZED UNIT OVERLOAD
•M1006C206 RRC CONN REJECT DUE TO BUFFER LIMIT CTRL
•M1006C208 RRC CONN REJECT DUE TO RNC RESTART
When the RNC sends RRC CONNECTION REJECT message to the UE because the RNC has recently restarted and the max
Yes---RAB Setup failure received?---No ( chk failure cause)
Yes (chk failure cause--Not Radio related Problem/Cell U
RAB Setup fails occurs (due to AC, BTS, frozen BTS, Transp, Iur Trans, Iu-CS Trans, Iub AAl2
then RNC sends RANAP: RAB Assignment Response msg. to CN, sending appropriate failure cause.
RAB Access fails occurs (due to UE & RNC fails)-----

UE sends RB setup failure msg. to RNC, RNC sends RAB Assignment response to CN, + Iu release requ
RAB Active fails occurs (due to Radio, Iu, Iur, Iub, RNC internal fails)-----
RAB setup & Access Fail Root Cause Analysis

RAB_CONN_STP_FAIL_AC (dominant) [ Admission control could reject establishment of new Connection/b
•Check UL Interference (R99 Noise Rise, RTWP- Cell Power Report), DL Power (HSDPA, R99 power) & DL Cod
•UL Power Spikes -> Disable UL Admission Control to if the number of failures is critical (PrxTarget-> 30 dB), imple
•When HSPA is enabled in the cell, the DL and UL resources are shared between HSPA and R99 users
–Both R99 and HSPA should be monitored-- Cell utilization + Allocated_Traffic_Amounts_(R99
–From the HSDPA side, besides of blocking, HSDPA throughput limitations can be also monitored
RAB_CONN_STP_FAIL_BTS (dominant when HSDPA active)

•Check BTS configuration in terms of CE allocation – Use Channel Element (M5001) Counters in order to evalu
•Expand the Capacity or decrease the traffic offered to the site--- Check Uplink CE Usage(shouls not be >8
•Frozen BTS/BTS not responding-- delete and re-create COCO/Site Reset
RAB_CONN_STP_FAIL_TRANS
•Evaluate Number of reconfiguration failure due the transmission-- Traffic_on_Physical_Medium_Sub-Layer & I
•Expand the capacity or decrease the traffic offered to the site
For ATM based Iub
•Check COCO Configuration
•Check RAB_STP_FAIL_XXX_IUB_AAL2, M1001C531-C533
•Use AAL2 Multiplexing in case of two WAM
For IP based Iub---•Check IP based route parameters (ZQRL;)/ IP_Route_Resource_Reservations Report
DCH Reconfiguration failures due to AC/BTS/Trans-- NRT_DCH_Allocations_Statistics report

SHO Branch setup fails BTS/Iub-- SHO Overhead Report--No. 88, traffic
RAB_CONN_STP_FAIL_RNC
RAB_CONN_STP_FAIL_ICSU_OVERL
•ICSU overload
RAB_CONN_STP_FAIL_RNTI ALLO FAIL

• RNC decides to reject RRC connection request due to RNTI allocation failure caused by RRMU overload
RAB_ACC_FAIL_Iur trans--- RNC capacity Report

RAB_ACC_FAIL_IuCS trans--- IuCS Report(94)
RAB_ACC_FAIL_Iub AAl2 fails--- •Check RAB_STP_FAIL_XXX_IUB_AAL2, M1001C531-C533, •Use AAL2 Multiplexing in c
RAB_ACC_FAIL_XXX_MS
•Evaluate Cell resource Prx and Ptx (for example high uplink interference)--NRT_Radio_Bearer_stats report
•Check RB reconfiguration failure ratio ( If ATO setting is insufficient , rec. 500ms)--- RRC signalling report
RRC_CONN_ACC_FAIL_RADIO (Dominant failure cause type)

• Perform drive test to detect if UL or DL coverage Coverage or interference-- C
–UL Coverage
–DL Coverage
/ Coverage Optimization-- PRACH_Propagation_Delay Report
Packet Service & Session [ PS ]

Packet Service - A call with RABQoS parameters: Traffic Class = Interactive or Background.
•The RRC setup has been done with cause codes: MOC Interactive, MTC Interactive, MOC Background or MTC B
Packet Session - A call with RAB/RB QoS parameters: Traffic Class = Interactive or Background.
•Here a call refers to the DCH/HS-DSCH/E-DCH live time, that is, the time the session is active for traffic.
•The RRC setup has been done with cause codes: MOC Interactive, MTC Interactive, MOC Background or MTC B
Packet calls starts with user plane capacity allocation (transfer from FACH/PCH, DCH 0/0) and ends with dedicated resource re
There are counters for the following channel combinations
•Rel99 DL = DCH UL = DCH
•HSDPA DL = HS-DSC UL = DCH •There could be multiple p
•HSUPA DL = HS-DSC UL = E-DCH • RU20 introduce Direct re
Packet Session RAB Setup Failures

AC, BTS, Frozen BTS, RNC, ANCH fails
Packet Session RAB Access Failures
UE, RNC fails
Packet Session Setup Failures (R99)

Initial Setup fail procedure
•AC failure : lack of DL power or high UL interference
•BTS failure: lack of HW capacity
•DMCU failure: lack of DSP resources in RNC
(DSP resource usage/ DSP state changes/ DSP service statistics reports)- hardware
•TRANS failure: lack of Iub capacity (COCO parameters)

•UE failure: UE internal problem (not capability issue)
•Other Failures
HSDPA Setup fails reasons: RNC, BTS, Iub, UE, UL-DCH, Multi-RAB, Max. users, DL Pwr limit
HSDPA
HSDPA Setup fails reasons: RNC, BTS, Max. users, UE, E-DCH not selected due to too many
HSUPA
overage Optimization-- PRACH_Propagation_Delay Report
nterferer Around BTS) PrxNoise value between -99.5 dBm and -103.5 dBm. In Tmo=-105dbm
fails, RNC, RNTI & ICSU fails)--- then sends RRC connection setup reject msg.
PA, R99 power) & Code occupancy if there is need to upgrade radio capacity-- [ HSPA no. of Users ] Cell Utilization/capacity Report
PrxTarget-> 30 dB), implement TN159
unters in order to evaluate lack of Channel Elements-- NodeB Utilization/CE Utilization Report
Usage(should not be >80-85%--- NodeB Utilization/CE Utilization Report)
Example
Short One day dat-- to show top
Medium_Sub-Layer & Iub Capacity reports •Majority of BTS Failures is com
•Check CE usage for these site
One site detail analysis show that Average UL CE usage ratio is above
Reservations Report
stem reset/user reset & DSP_Service_Statistics reports
NBAP Signalling
ronization Fail/ RNC Internal failures)-- RRC Access fails

( RRC Active fails-- a) Radio Fails---
Ue fails---
RNC Internal fails--
elease can be due to-- ISHO, IFHO, SRNC Relocation, Pre-emption
or interference-- Cell Power Report
eighbor chk / best server Ec/No should not be less than -12db
Missing
essage from RNC./ Antenna tilt(CPICH RSCP should neighbor/ checks-- for neighbor optimization
not be<-102dbm)
R (offset parameter) has been increased (0-> -2 dB->-4 for networks with lot of smartphones)
DL (if UL interference is not the cause)
distance area or close to cell edge area

tup distance during RRC connection request or cell update
non-optimum cell coverage from neighbouring cells
ly restarted and the maximum number of RRC connection establishments is limited until a guard timer expires.
lated Problem/Cell Update)
CS Trans, Iub AAl2 fails)-----

te failure cause.
N, + Iu release request to CN
ent of new Connection/bearer ]

PA, R99 power) & DL Code occupancy if there is need to upgrade radio capacity-- [ HSPA no. of Users ] Cell Utilization/Capacity Report
PrxTarget-> 30 dB), implement TN159
and R99 users
_Traffic_Amounts_(R99_+_HSPA) report
s can be also monitored-- Node B utilization/ HSPA Overview/
Number_of_HSPA_Users_and_UE_capability/ MAC-hs_Retransmissions_by_Code_and_Modula
unters in order to evaluate lack of Channel Elements-- NodeB Utilization/CE Utilization Report
Usage(shouls not be >80-85%--- NodeB Utilization/CE Utilization Report)
•Check M1005C128 CANC_ADD_SRNC_TRA

Medium_Sub-Layer & Iub Capacity reports i.e. (The number of cancelled synchronised rad
due to a transmission setup failure or RNC DMP
Reservations Report
stem reset/user reset & DSP_Service_Statistics reports
NBAP Signalling
e AAL2 Multiplexing in case of two WAM, Iub Capacity report, NRT_Radio_Bearer_stats--AAl2 congestion
dio_Bearer_stats report for Prx & Ptx ratio –UL Coverage tuning
RC signalling report §Tune C
–DL Coverage tuning
§Tune S
or interference-- Cell Power Report
eighbor chk / best server Ec/No should not be less than -12db
essage from RNC./ Antenna tilt(CPICH RSCP should not be<-102dbm) / Missing neighbor checks--
C Background or MTC Background.
active for traffic.

C Background or MTC Background.
ith dedicated resource release (transfer back to FACH/PCH, DCH 0/0, RAB release, outgoing relocation, HHO, ISHO)
There could be multiple packets inside single RAB

RU20 introduce Direct resource allocation for HSPA
s)- hardware
users, DL Pwr limits. 1. If high HSDPA Access Failure _too many HSDPA users --
§Check simultaneous HSDPA users--- Number
§DCH selected due to too many HSDPA users, R
Now -- check schedular type: 16 users/cell, 64 users/cell, shared sche
Schedular type defined in WBTS commissioning parameter---
•If shared scheduler is used, the number of schedulers depend on Tce
Wrong scheduler type may cause HSDPA setup problems due to too m
Can cause High HS-DSCH set up fails during busy hrs due to max use
2. If high HSDPA Access Failures_UL DCH (RNC_661c/d)

§Rejected HS-DSCH return channel due to lack o
Check--RSRAN071_-_Utilization_Shares_of_Total_Traffic_Allo
chn bitrate utilization(16,64,128,384)
§Monitor UL load --chk UL power congestion ( lac
3. If high HSDPA Access Failure_UE
§Check RB reconfiguration failure rate-- termina
§ICSU log for UE types troubleshooting ?
4.If high HSDPA Access Failure_BTS
§Lack of UL channel resources (check CE resour
§Too high SHO overhead – all branches must h
SHO Overhead chk--- cell level report--should be nearly 40
Software bugs in BTS hardware with some features.
5. HS-DSCH return channel setup fail due to Iub transport
–Breakdown the failure distribution (64,128,384,MAC-d)
–Evaluate number of reconfiguration failure due the transmiss
–Check M1005C128 CANC_ADD_SRNC_TRAN_STP_FAIL
–Check RAB_STP_FAIL_XXX_IUB_AAL2, M1001C531-C533
6. HSDPA setup fail due RNC internal reason

–Check RNC Unit load (DMPG)
–Max number of users/RNC
–DSP failures and faulty alarms
d due to too many hsupa users, AC Fails.
If HSDPA setup is failing also HSUPA setup will fail, but it could be also th
RNC_956a E-DCH Setup FR du
RN E-DCH Setup FR du
Also there could be too many HSUPA users
RN UL DCH Selected du
HSUPA setup failed due to BTS reports HSUPA cannot be a
RN E-DCH Not Selected
M1000C268-C270 – These counters measure th
EDCH cannot be allocated in case HSUPA is not supported in SHO bran
RNC_1103a E-DCH Allocation F
For static resource allocation the power could limit
RNC_969a DL DCH Selected du
.5 dBm. In Tmo=-105dbm(Nokia default=-105dbm)
lization/capacity Report
hort One day dat-- to show top 10 sites having highest number of BTS failures
Majority of BTS Failures is coming from few sites.
Check CE usage for these sites - > add CE capacity if needed or try to reduce the usage
e UL CE usage ratio is above 90% causing high blocking -> Capacity issue
•Configuration & SW issues
Utilization/Capacity Report Setup Failures due Ad
Number_of_HSPA_Users_and_UE_capability report •RRC/RAB cs s
•RAB PS setup
_by_Code_and_Modulation_Usage reports •HSDPA Acces
•HSDPA access
C128 CANC_ADD_SRNC_TRAN_STP_FAILfailure)
ncelled synchronised radio link reconfigurations on SRNC side
setup failure or RNC DMPG/DSP resource allocation)
–UL Coverage tuning
§Tune Cell Dominance (or CPICH) if the cause is UL interference
–DL Coverage tuning
§Tune SCCPCH Power if UE does not receive the RRC Setup Message from RNC.

SDPA users --
ous HSDPA users--- Number_of_HSPA_Users_and_UE_capability report
e to too many HSDPA users, RNC_660b---- Number_of_HSPA_Users_and_UE_capability report
64 users/cell, shared schedular/ full baseband schedular
ssioning parameter--- as HSDPA shared schedular type license
schedulers depend on Tcell parameter settings on the site.
up problems due to too many users, or waste baseband capacity if schedulers are underutilized.
busy hrs due to max users reached.
_UL DCH (RNC_661c/d)

CH return channel due to lack of UL radio resources
hares_of_Total_Traffic_Allocation_Amounts report-- for HS-DSCH return
84)
-chk UL power congestion ( lack of radio resource for UL return channel)-- cell capacity report
guration failure rate-- terminal problem-- RRC signalling report

types troubleshooting ?
el resources (check CE resource utilisation using M5001 counters at BH)

verhead – all branches must have enough CE capacity if UE is in SHO when HS-DSCH allocation is started
port--should be nearly 40%.
th some features.
p fail due to Iub transport
tion (64,128,384,MAC-d)
ration failure due the transmission-- RRC signalling report
DD_SRNC_TRAN_STP_FAIL
_IUB_AAL2, M1001C531-C533
ernal reason
p will fail, but it could be also that only HSUPA will fail. The reasons are similar to HSDPA
E-DCH Setup FR due to BTS (RL reconfiguration failure to RNC)
E-DCH Setup FR due to Transport (RL reconfiguration cancel from RNC)
E-DCH Setup FR due to UE (RB reconfiguration failure from UE)--terminal problem-- RRC signalling report
E-DCH Setup FR due to Other Failures (RNC internal reason)
UL DCH Selected due to too many HSUPA users

TS reports HSUPA cannot be allocated
E-DCH Not Selected due the BTS HW (BTS sent radio resource measurement report)
0 – These counters measure the BTS HW limitation during HSUPA Calls
A is not supported in SHO branch
E-DCH Allocation FR due to Not Acceptable Active Set
DL DCH Selected due to the HSDPA power (HSDPA static power allocation in use)
etup Failures due Admission Control - AC
•RRC/RAB cs setup failures due AC - Admission control rejects the establishment of new RRC/RAB connection due the
–UL Power, DL Power and DL Codes
•RAB PS setup failures due AC – Admission control rejects the establishment of new PS radio bearer due the
–UL power, DL Power, DL codes and too many users in the scheduler
•HSDPA Access failures due the UL DCH – AC rejects the establishment of new HSDPA connection (related to HSDPA UL retur
–UL power
•HSDPA access failures due number of HSDPA users reached – new HSDPA connection is rejected due too many HSDPA users
AB connection due the
arer due the
ion (related to HSDPA UL return channel)
ed due too many HSDPA users

 Total_Numberof_Radi Lnks 
SHO_verhad10% 1
1.1.1.1.1. Retainibility Analysis (CS/PS/HS)
Voice Drop Call Optimization:
1. Monitor Daily Performance Reports/KPIs Worksheet---Pick Worst Offenders
2. Identify DCR top offenders…. few cells?…. Any particular area ? Known Coverage issue? Need a
3. check cell & its neighbor cells availability (availability should be 100%)---- cell level report
4. Check current alarms on the site / sector & same for neighbor cells?--- alarm history especial
6. Check if the sector is dropping the calls due to RF (Radio fails)-- Not RF(Iu, Iur, BTS, RNC, M
7. If not RF, check :
• Voice Drops due to Iu
Check core network parameter setting if RAB_ACT_FAIL_XXX_IU
Check SCCP SGSN/RNC IuPS Tias/Tiar if RAB_ACT_FAIL_BACKG_IU
• Voice Drops due to Iur

• Voice Drops due to BTS

-- Check if any BTS faulty alarm (7651, 7653, 7654 alarm)
•If No alarms-- delete and re-create COCO/COCO reset/Site Reset---may be due to Frozen BTS/BTS not re
•Expand the Capacity or decrease the traffic offered to the site--- Check Uplink CE Usage(shouls not be >8
• Voice Drops due to RNC

•ICSU overload
• RNC decides to reject RRC/RAB connection RRMU overload, priority calls during Busy hrs
• Voice Drops due to UE

–Check physical channel reconfiguration failure rate (IFHO, ISHO, code optimisation)
•Evaluate Cell resource Prx and Ptx (for example high uplink interference)--NRT_Radio_Bearer_stats report
•Check RB reconfiguration failure ratio ( If ATO setting is insufficient , rec. 500ms)--- RRC signalling report
• Voice Drops due to CIPH
• Voice Drops due to Trans

RAB_ACC_FAIL_IuCS trans--- IuCS Report(94)
RAB_ACC_FAIL_Iub AAl2 fails--- •Check RAB_STP_FAIL_XXX_IUB_AAL2, M1001C531-C533, •Use AAL2 Multiplexing in c
7. If drops are due to RF (Voice Drops due to Radio fails), check the Site location, Neigh
Number_ofBstServ_RadioLnks
 
Need Tilt / Azimuth change to improve the area?
–UL Coverage
–DL Coverage
/ Coverage Optimization-- PRACH_Propagation_Delay Report ( Cell range in TMO Sit
9. HO issue/HO fails? All Neighbor Exists? SHO….ISHO……IFHO…….?? Neighbor Add/dele

Check SHO KPI if performance < 90% ( leads to Radio failure)--- Yes
–Check if cells are at RNC border
Yes-- (check Iur capacity and SRNC relocation problem)
No-- SHO_Adjacencies(46)--neighbor add/delete, Soft_Handover_Performance(28), Active_S
–Detect badly performing neighbours using HO success rate per adjacency counters--
check SHO Overhead  Total _ Number _ of _ Radio _ Links
SHO _ Overhead  100%  
 Number _ of _ Best _ Server _ Radio _ Lin
Check SHO Overhead (RNC_79b) to see how big is SHO area, if it is too small SHO may fails a
–High incoming HO failure rate in all ADJS – check sync alarms

–Audit Adjacent sites for Alarms/capacity/traffic and visualization check with map
–Evaluate HO control parameters and trigger threshold
If SHO KPI> 90%-- check ISHO failures?

No ISHO failures--- new site needed?/ RF & IFHO Neighbor Optimization
Yes ISHO failures (ISHO Reports)---
Check No cell found ratio>40% or not?-- Inter-System_Handover_Performance report
If No cell found ratio >40%-- 3G cell at inter-RNC border/ 3G cell covers a coverage hole---
–Check missing neighbour/badly performing neighbors(ISHO Adjacencies report),
Coverage_Quality_ISHO_Performance_per_Cause reports--- UL DCH qual, UE tx pwr, DL DP
GSM frequency plan neighbour RNC and MSC database consistency audit( for BCCh/BSIC co
check alarm of reference clock in 3G or in 2G,
check 2G TCH congestion
4.Check ISHO KPI if RT ISHO < 90% or NRT < 80% (leads to radio failure)
If No cell found ratio is>90% & enough ADJIs--- Wrong reference Clock tuning( 10MHz tunn
If No cell found ratio<40% & ISHO Success rate<90%----- Investigate 2G
TCH Blocking/TCH congestion/TCH fa
5. Detecting DL or UL path loss problem if RAB drop due to radio (dominant call drop cause >
–Check ASU failure rate (UNSUC_ASU) which link to NO RESPONSE FROM RLC
–Mapping radio failures with Tx power and CPICH related parameters -> CPICHToRefRA
–Check Call reestablishment timer -> T315 (rec.10s)
–Ecno distribution for bad coverage issue (M1007C38-M1007C47)
RRC active drops reasons:
Iu
Iur
BTS
RNC
MS
CIPH
UE
Trans
Radio fails
Ciphering
R99 PS Drop Call Optimization:

 
10. It might be observed on some sites that although there is no alarm and cell is carryin
RAB AMR active drops reasons:

Iu
Iur
RNC
MS
UE
Trans
Radio fails
R99 is NRT service basically
PSSR rate can be monitored separately for R99, HSDPA and HSUPA
Packet Session Analysis

Packet call normal releases (normal end of the call) counters includes
• Transition to DCH 0/0, Cell_FACH or Cell_PCH due to inactivity or low utilisation
• Outgoing SRNC relocation
• Inter-RNC hard handover
• Inter-system Hard Handover
Packet call Failures are divided into
•RL fails
•Other Non-RL Fails
•Pre-emption
HSDPA Retainability •The normal transition from HS-DSCH to FACH/DCH are considered as a normal HS-DSCH rel
HSDPA Drop reasons: RL fails, Non-RL fails, Mobility fails, Pre-emption fails, other fails
ATO=Offset for activation time of SRBs on HSPA= 300 to 500ms

Ptx target=40dbm
Prxtarget=5dbm
CPICH tx power= 35.1dbm
Check NBAP RL reconfiguration failure rate?

NBAP_Signalling report-- Radio link - SRNC, Radio link - DRNC, RL setups/reconf fails for HSDPA MAC-d
NBAP_Signaling_per_cause report--- RL setup for an RRC connection-Fail, BTS not respond, RL operatio
Required ICSU log for further tro

HSDPA Retainability •The retainability of all successfully allocated E-DCH resources for NRT traffic
HSUPA Drop reasons: RL fails, Non-RL fails, E-DCH RelRate(HS-DSCH SCC), other fails
o_Links
1
Drop Call Rate (DCR)
Call Drop rate (CDR) is calculated based on RAB activation failures
• Call is dropped if one (or more) of the following RAB, RB or RL, drops
Coverage issue? Need a new site ?
---- cell level report
alarm history especially for transmission issues (NBAP link failures/T1 fluctuations?)
RF(Iu, Iur, BTS, RNC, MS, CIPH, UE, trans fails)
ue to Frozen BTS/BTS not responding
er cause Report
k CE Usage(shouls not be >80-85%--- NodeB Utilization/CE Utilization Report)
SAP/NBAP Signalling
s- System reset/user reset & DSP_Service_Statistics reports
O, code optimisation)
T_Radio_Bearer_stats report for Prx & Ptx ratio
s)--- RRC signalling report
•Use AAL2 Multiplexing in case of two WAM, Iub Capacity report, NRT_Radio_Bearer_stats--AAl2 congestion
he Site location, Neighbors, Cell to cell HO stats(SHO,IFHO,ISHO), PRACH delay distance and Ec/No
Radio_Lnks

sing Neighbor chk / best server Ec/No should not be less than -12db Coverage or interferen
tup Message from RNC./ Antenna tilt(CPICH RSCP should not be<-102dbm) / Missing neighbor checks-
Cell range in TMO Sites-20Kms)
….?? Neighbor Add/delete?
erformance(28), Active_Set_Size_for_NRT-RT_Traffic--active set update fails-- check ad/delete/replacement wind

per adjacency counters-- delete/create them again,
otal _ Number _ of _ Radio _ Links  From cell level report
1
ber _ of _ Best _ Server _ Radio _ Links 
t is too small SHO may fails and if too big capacity is wasted
ation check with map
ers a coverage hole---- RF & ISHO neighbor optimization

Adjacencies report),
CH qual, UE tx pwr, DL DPCh, RSCP/EcNo, IMSI, Emergency drops, PRx total, PTx Total, drops due to service base
y audit( for BCCh/BSIC collision)
k tuning( 10MHz tunning)
g/TCH congestion/TCH failures/2G traffic/2G coverage & Interference
ominant call drop cause > 50%)

SPONSE FROM RLC
ameters -> CPICHToRefRABOffset, PTXDPCH MAX
Iu
Iur
RNC
MS
UE
Trans
Radio fails

arm and cell is carrying traffic, some HW faults ( could be found only during the site visits) causing
Packet service RAB active, drops reasons:
NRT PS RAB active fail due to---
2. BTS--
Active_Set_Size_for_NRT-RT_Traffic report
Packet session, drops reasons:
HS-DSCH/E-DCH DR, RL
HS-DSCH/DCH DR, RL
DCH/DCH DR, RL
HS-DSCH/E-DCH DR, Other
HS-DSCH/DCH DR, Other
DCH/DCH DR, Other
1. Radio-- Chk NRT Radio Bearer fails due to radio--- NRT_DCH_Allocations_Statistics/ NRT_R
chk BTS HW resources-- NRT_Radio_Bearer_stats report for BTS congestion

Failed SCC due to HSDPA return channel-- chk SCC fails-- Service_Session_Reta
HSPA_Serving_Cell_Change report-- for reasons, causes, fails
SCC=Serving Cell Change
3. Iu-- chk core network parameter settings---
4. Iur-- Inter RNC mobility?
5. RNC-- RNC Internal problem
6. UE-- Terminal problem
Release due to RL Failure counters: Release due to Other Failure counter

M1022C57 PS_REL_RL_FAIL_HS_E_INT M1022C63 PS_REL_OTH_FAIL_HS_
M1022C58 PS_REL_RL_FAIL_HS_E_BGR M1022C64 PS_REL_OTH_FAIL_HS_
M1022C59 PS_REL_RL_FAIL_HS_D_INT M1022C65 PS_REL_OTH_FAIL_HS_
M1022C60 PS_REL_RL_FAIL_HS_D_BGR M1022C66 PS_REL_OTH_FAIL_HS_
M1022C61 PS_REL_RL_FAIL_D_D_INT M1022C67 PS_REL_OTH_FAIL_D_D
M1022C62 PS_REL_RL_FAIL_D_D_BGR M1022C68 PS_REL_OTH_FAIL_D_D
are incremented in case RL Failure is received from BTS and are incremented in case the PS alloca
cannot be acquired back during specific time any other reason expect normal, pre-
M1022C57 PS_REL_RL_FAIL_HS_E_INT M1022C63 PS_REL_OTH_FAIL_HS_
M1022C58 PS_REL_RL_FAIL_HS_E_BGR M1022C64 PS_REL_OTH_FAIL_HS_
M1022C59 PS_REL_RL_FAIL_HS_D_INT M1022C65 PS_REL_OTH_FAIL_HS_
M1022C60 PS_REL_RL_FAIL_HS_D_BGR M1022C66 PS_REL_OTH_FAIL_HS_
M1022C61 PS_REL_RL_FAIL_D_D_INT M1022C67 PS_REL_OTH_FAIL_D_D
M1022C62 PS_REL_RL_FAIL_D_D_BGR M1022C68 PS_REL_OTH_FAIL_D_D
are incremented in case RL Failure is received from BTS and are incremented in case the PS alloca
cannot be acquired back during specific time any other reason expect normal, pre-
ered as a normal HS-DSCH release (including transitions due to mobility and pre-emption)
on fails, other fails 1. RL Fails Compare RL fails with -- Cell Upd ATT RL Fails & Cell Upd ATT RLC Fails--re
Check SCC Failure rate--HSPA_Serving_Cell_Change report (HSDPA
Radio fails -- UL coverage(TMA/MHA chk) & Interference
DL coverage & Interference-- PRACH delay range r
Neighbor Optimization etc.
Iub -- HSPA Overview report-- for Iub congestion
RAB_ACC_FAIL_Iub AAl2 fails--- •Check RAB_STP_FAIL_XXX_IUB_A
•Use AAL2 Multiplexing in case of two WAM, Iub Capacit
NRT_Radio_Bearer_stats--AAl2 congestion
Iub_Traffic_-_FP_layer report-- for rejections, discarded fram
CE resource congestion--- CE utilization/Cell capacity/Number_of_H
Check CQI distribution (HSPA Overview report)

EcNo distribution for bad coverage issues- (M1007C38-M10
Check Active_Set_Size_for_NRT-RT_Traffic report-- Active set update
Check HSDPA FMCS Mobility Control Parameter --(Add/Drop window,
Check call re-establishment T315 timer due to radio link failure 9 (60
2. Non- RL Fails/Others-- Check

UE responding with some failure msg or not responding to some msg, but no RL
Chk RNC fails & use RNC logging If required
Check RB reconfiguration, physical channel reconfiguration, NBAP RL r
RB reconfiguration failure ratio ( If ATO setting is insufficient , rec. 500
Evaluate Cell resource Prx and Ptx (for example high uplink interfere
nf fails for HSDPA MAC-d flow

not respond, RL operations- RL fails(SRNC,DRNC), RL setup for HO failures, SRNC/DRNC(SHO/HHO-BTS not resp
CSU log for further troubleshooting ?

or NRT traffic
SCC), other fails
•There are several reasons for HSUPA release:

–RNC_1108a E-DCH Rel due to RL Failures
–RNC_1109a E-DCH Rel due to other failures
•RL fail is incremented If:

– a radio link failure happens during HSDPA call
– uplink RLC unrecoverable error happens (Cell Update
– RLC-entity in RNC reports RLC protocol reset
Cell capacity report -- UL load- HSUPA Physical CH pwr

HSPA serving cell change report -- HSUPA SCC- E-DCH down to D
Soft handover performance report -- HSUPA SHO Success Rate
HSPA Overview report -- HSUPA(2ms/10ms TTI thp, E-DCH 2m

HSUPA usage( happy Bit rate, 2ms/10ms TTi trans usage rate,
correctly/ceived correctly but lost)
Number_of_HSPA_Users_and_UE_capability report -- hsupa simu
Traffic_on_AAL5 report
on RAB activation failures
lowing RAB, RB or RL, drops.
y distance and Ec/No quality distribution statistics

overage or interference-- Cell Power Report
elete/replacement window
ops due to service based HO

e site visits) causing call drops e.g. bad feeder or antenna or MHA problem?
cations_Statistics/ NRT_Radio_Bearer_stats/ SHO Overhead NRT_RT chk?/
for BTS congestion

Service_Session_Retainability report--for HS_DSCH SCC fails
e due to Other Failure counters:

C63 PS_REL_OTH_FAIL_HS_E_INT
C64 PS_REL_OTH_FAIL_HS_E_BGR
C65 PS_REL_OTH_FAIL_HS_D_INT
C66 PS_REL_OTH_FAIL_HS_D_BGR
C67 PS_REL_OTH_FAIL_D_D_INT
C68 PS_REL_OTH_FAIL_D_D_BGR
emented in case the PS allocation is released due to
er reason expect normal, pre-emption or RL failure
C63 PS_REL_OTH_FAIL_HS_E_INT
C64 PS_REL_OTH_FAIL_HS_E_BGR
C65 PS_REL_OTH_FAIL_HS_D_INT
C66 PS_REL_OTH_FAIL_HS_D_BGR
C67 PS_REL_OTH_FAIL_D_D_INT
C68 PS_REL_OTH_FAIL_D_D_BGR
emented in case the PS allocation is released due to
er reason expect normal, pre-emption or RL failure
HS-DSCH Allocation release
ell Upd ATT RLC Fails--recoverable error ( present in retainability report)

hange report (HSDPA SCC fails due to UE,BTS,Trans,AC)-- high SCC failures lead to radio link failure
k) & Interference
e-- PRACH delay range report/tilt
ub congestion
RAB_STP_FAIL_XXX_IUB_AAL2, M1001C531-C533,
two WAM, Iub Capacity report,
congestion
ejections, discarded frames & lost PDUs with reasons
ell capacity/Number_of_HSPA_Users_and_UE_capability(Simultaneous users, NRT DCH select due to too many hs
ues- (M1007C38-M1007C47, CPICH EcNo class 0-9)
ort-- Active set update fails, 1-2-3 cells (% & no.) in active set for different RT & NRT services
er --(Add/Drop window, handover or SCC too late, SCC parameter)
o radio link failure 9 (60 secs in TMO)
to some msg, but no RL failure (timer expiry)
figuration, NBAP RL reconfiguration failure rate

g is insufficient , rec. 500ms)--- RRC signalling report
ple high uplink interference)--NRT_Radio_Bearer_stats report for Prx & Ptx ratio
(SHO/HHO-BTS not respond/other cause)

E-DCH Allocation release
during HSDPA call

error happens (Cell Update by UE)
RLC protocol reset
sical CH pwr
A SCC- E-DCH down to DCH, Inter RNC
UPA SHO Success Rate
ms TTI thp, E-DCH 2ms TTI utilization), HSUPA Transmitted Power Ratio,
TTi trans usage rate, MAC-e PDU not transmitted/not received
ty report -- hsupa simultaneous users, hsdpa/hsupa user distribution

to radio link failure
elect due to too many hsdpa/hsupa users)

SHO success rate
SHO_Adjacencies
SC_INTRABUCESFL_INTRBSUCEFL
•SHO success rate KPI (RNC_195a) is informing how many successful Active set updates we will have, comp
RNC_153b SHO SR, RT
RNC_192b SHO SR, NRT
SHO Reports:
Soft_Handover_Performance Cell level AS update RT+NRT, RT Update % - 1a,1b,1c, NRT U
Cell level
SHO adjacencies are checked to increase SHO Success R
then decide whether neighbor is to be added or not.---- A
Check SHO KPI if performance < 90% ( leads to Radio failure)--- Yes
–Check if cells are at RNC border
Yes-- (check Iur capacity and SRNC relocation problem)
No-- SHO_Adjacencies(46)--neighbor add/delete, Soft_Handover_Performance(28), Active
–Detect badly performing neighbours using HO success rate per adjacency counters--
check SHO Overhead  Total _ Number _ of _ Radio _ Links
SHO _ Overhead  100%  
 Number _ of _ Best _ Server _ Radio _ L
Check SHO Overhead (RNC_79b) to see how big is SHO area, if it is too small SHO may fails
–High incoming HO failure rate in all ADJS – check sync alarms

–Audit Adjacent sites for Alarms/capacity/traffic and visualization check with map
–Evaluate HO control parameters and trigger threshold
Check if DL Active set update received(Active_Set_Size_for_NRT-RT_Traffic Report)

No-- SC clash?---yes(fix SC clash)
no --- congestion on target cell ( Load optimization)
DL Tx power max.?---yes ( in this case; Link is unbalanced--- do CPICH Op
Yes-- UE Tx Power max.?--- no(chk RF levels)
yes( check Uplink interference? )
RNC_73A10%
SHO based on DSR( Detected Set relation)-- Enabled in TMO
Example: SHO Parameters Changed
–FMCS: AdditionTime = 100 ms

–FMCS: DropWindow = 6 dB
–FMCS: DropTime = 640 ms
•Periodical reporting intervals
If UL interference----load optimization/Externa
•Replacement parameters were changed in live network in the RU10 pilot:

–FMCS: ReplacementWindow 2dB -> 6dB
–FMCS: ReplacementTime 100ms -> 640ms
•Addition and drop parameters were:
–FMCS: AdditionWindow = 4 dB
–AdditionReportingInterval = ReplacementReportingInterval = 0.5s

–DropReportingInterval = disabled (now event based as in RAS06)
SHO Update Attempt RT Same, SHO success ratio RT increased from 99.8 to 99.9% and above.
RAB Attempts CS Voice same, RAB Success ratio CS Voice increased from 99.4 to 99.6%.
ISHO Success Rate

SC_TAREDPIHCNOS_TAREDULI OR
The inter-system handover measurement is carried out in the serving RNC (SRNC)
The RT and NRT Inter System HO differs in nature. Therefore the ISHO KPI can be spitted in RT and NRT parts
•ISHO success rate for RT services (RNC_300g)
•ISHO success rate for NRT services (RNC_301e)
If RRC connection drops during ISHO… TRelocOverall timer expires[8sec](in case of RT); RRCtmriRCCl
cause can be: CPICH RSCP, CPICH EcNo, UL-DCH, TxPwr, DL-DPCH
If No cell found ratio >40%-- 3G cell at inter-RNC border/ 3G cell covers a coverage hole---
If No cell found ratio is>90% & enough ADJGs--- Wrong reference Clock tuning( 10MHz tunn
If No cell found ratio<40% & ISHO Success rate<90%----- Investigate 2G
TCH Blocking/TCH congestion/TCH f
ISHO Cancellation
•The inter-system measurement phase takes a few seconds and during that time the conditions in the WCDMA lay
–Event 1E cancellation
–AS Update (1A or 1C) can also cancel ISHO in case of RSCP or Ec/No triggered ISHO
§If the CPICH Ec/No or the CPICH RSCP of this cell is found to be greater than or equal t
•No cancellation once measurement phase is completed
Parameters:
•Activation per RNC required with parameter RNC: ISHOCancellation
•Enabled per trigger reasons with parameters FMCG: ISHOClcauseXXX
•Parameter FMCG: DLDPCHTxPwrClOffset allows to influence cancellation (-3 in TMO)
•RNC: MaxNumISHOClPerAS sets the maximum number of ISHO cancellations per UE and per active se
Steps to Improve ISHO SR:

1. Multiple BSIC Identification feature enabled chk?-- BSIC Identification of max. 3 GSM carriers
MultipleBSICIdent parameter---must be set to 'on'
MaxBSICIdentTime is 3 or 4 seconds if the overall procedure of HandOver to GSM is close to typical va
2. ISHO parameter threshold changes

3. Force Decode BSIC feature for NRT--> •ISHO success rate improved a lot -> ISHO cell fou
4. Missing ADJG/bad performing neighbors(SR/Adjacency)-- ISHO Adjacencies report---> to
5. Compressed mode parameter set changes
6. GSM Measurement reporting parameters changes
7. Changes in Decision Algorithm parameters
a) AdjgTxPwrMaxTCH-- Maximum UE TX Power on TCH(HCConfiguratio
b) AdjgRxLevMinHO (n)--- minimum required GSM RSSI level----------------------->
c) GsmMeasAveWindow -- kitni measurement report se RNC avg GSM RSSI value
ISHO Parameters
CPICH RSCP (Event 1F)
Thresholds:
HHoRscpThreshold DL DPCH power
HHoRscpCancel Threshold:
L3 filter: HHoRscpFilterCoefficient GsmDLTxPwrThrXX
Timers: Data rate threshold
HHoRscpTimeHysteresis HHOMAxAllowedBitrateDL
HHoRscpCancelTime
UE Tx Power (Event 6A)

Threshold:
GsmUETxPwrThrXX
L3 filter: GsmUETxPwrFilterCoeff 2. GSM measurement reporting
Hysteresis margin: GsmMeasRepInterval
GsmUETxPwrTimeHyst GsmNcellSearchPeriod
Data rate threshold GsmMinMeasInterval
HHOMAxAllowedBitrateUL GsmMaxMeasPeriod
(XX=AMR,CS,NrtPS,RtPS)
3. Decision Algorithm
AdjgTxPwrMaxTCH
AdjgRxLevMinHO (n)
GsmMeasAveWindow
1.Triggering
2.GSM measuring
3.Decision
Handover Execution
Multiple BSIC identification – RU20

SC_TAREDIVS_UPCTARED_OH SN
•The RNC initiates BSIC identification to the UE for max three GSM carriers simultaneously.
•If the ISHO attempt to the best neighbour cell fails, a new attempt to the other cell can be started without new
–Reduces compressed mode measurements
–Increase ISHO success rate
•ISHO may fail if the initial BSIC identification of the best GSM cell (according to the GSM RSSI measurements) fa
•Instead of waiting the penalty period and then retrying the HO with new CM measurements, the BSIC identificatio
•This increases the probability of successful BSIC identification and allows another handover attempt to the secon
ISHO Failure Scenarios

CM start not possible
HS-DSCH Serving Cell Change
There seems not to be a relation with poor SCC success and HSDPA retainability.
SCC success rate for HSDPA and HSUPA is not very accurate in cell level as denominator is incremented in the source cell (old
UCESFL
updates we will have, compared to initial Addition/Replacement/Deletion requests.
% - 1a,1b,1c, NRT Update % - 1a,1b,1c, Events Ratio RT+NRT, HSUPA SHO Success Rate, CPICH EcN
ncrease SHO Success Rate, Target cells without neighbors are checked with their attempts & SR, Also their Avg
o be added or not.---- ADJs addition & deletion of neighbors with no share
erformance(28), Active_Set_Size_for_NRT-RT_Traffic--active set update fails-- check ad/delete/replacement wind

per adjacency counters-- delete/create them again,
otal _ Number _ of _ Radio _ Links
on check with map
RT-RT_Traffic Report)
anced--- do CPICH Optimization


ber _ of _ Best _ Server _ Radio _ Links
From cell level report
1

t is too small SHO may fails and if too big capacity is wasted
d optimization/External Interferer
–If UL SRB becomes overloaded, it can cause:

§Delayed HOs -> decreased KPIs
§NAS signaling problems
§RRC signaling problems
•These problems can be avoided by optimizing the following param
–Increasing ReplacementWindow
–Increasing ReplacementTime
–Changing the interval of the periodical reports
New value for ReplacementWindow for Event 1C must be set in rela

•FMCS: increase ReplacementWindow
–The amount of the ReplacementWindow increase depends
No exact value can be given.
•FMCS: increase ReplacementTime to 640ms

–UE measures CPICH Ec/N0 internally every 200ms
–Therefore practical ReplacementTime parameter values are
§Other values just cause delay (for example 320m
•Reporting happens on occasions 0
–This is valid also for event 1A and 1B
•Periodical reporting parameters
–AdditionReportingInterval
–ReplacementReportingInterval
–DropReportingInterval (RU10 parameter)
•Increase the interval of the periodical measurements or disable periodici
–Event 1C measurements are long, each occupying 160-200m
–If the measurement interval is too short, the whole UL SRB b
–Recommended way is to increase the interval from 0.5s
_ERO
and NRT parts
1. CM start possible?--No( Chk Admission Control rejection--> PRxTotal, PTxTotal)

AC rejects CM request due to Interference(UL/DL)
Radio Link(or physical channel) re-configuration failure--due to BTS/UE reasons--
Yes-- ISHO measurement Success?

y1. missing ADJG/bad performing neighbors(SR/Adjacency)-- ISHO Adja
2. 2G neighbors BCCH/BSIC collision chk
3. Alarm of reference clock in 3G or in 2G
4. TCH Blocking/TCH congestion( target GSM cell is fully Loaded)/TCH
5. Compressed mode parameter set checking
6. Too low ISHO triggering threshold
7. Strict ADJG minimum threshold

ADJG RxlevMinHO--(here set as -95dbm)
8. Poor GSM Coverage
se of RT); RRCtmriRCCl timer expires[8sec](in case of NRT);
rs a coverage hole---- RF & ISHO neighbor optimization

k tuning( 10MHz tunning)
g/TCH congestion/TCH failures/2G traffic/2G coverage & Interference
conditions in the WCDMA layer may change => Cancellation
riggered ISHO
to be greater than or equal to the threshold for event 1E
ons per UE and per active set
of max. 3 GSM carriers simultaneously
SM is close to typical value of 10 sec (GsmMeasRepInterval * GsmMaxMeasPeriod); visible benefit in reducing CM

GsmMeasRepInterval= 0.5sec
GsmMaxMeasPeriod= 6
a lot -> ISHO cell found ratio decrease
cencies report---> to be defined & corrected
---------> If Max. Output power of UE is < value of AdjgTxPwrMaxTCH parameter; RNC adds Power diff
---------------------> GSM neighbor cell must exceed the RSSI level of AdjgRxLevMinHO-- for a handover to be p
C avg GSM RSSI value for handover nikallegi---- 1...32 MeasRep, step 1 MeasRep, (6 in TMO
CPICH Ec/Io (Event 1F)

H power Thresholds:
HHoEcNoThreshold
X HHoEcNoCancel
ld L3 filter:
itrateDL EcNofilterCoefficient
Timers:
HHoEcNoTimeHysteresis
HHoEcNoCancelTime
ent reporting UL Quality

Timer
ULQualDetRepThreshold
Data rate threshold
HHOMAxAllowedBitrateUL
n Algorithm
wrMaxTCH
vMinHO (n)
AveWindow
Execution
2G-to-3G back prevention

GsmMinHoInterval
HER_ASON
multaneously.
ll can be started without new inter-system measurements in compressed mode.
GSM RSSI measurements) fails, or the target GSM cell is fully loaded.
ments, the BSIC identification for more than one GSM cell is performed.
andover attempt to the second or third best cell without repetitive GSM measurements if the first handover attempt fails.
Multiple BSIC identification can be enabled with The MultipleBSICIdent parameter which must be set to ‘on’ to
The MaxBSICIdentTime parameter limits the maximum time for BSIC identification measurements per cell. If d
•The MaxBSICIdentTime parameter must be configured with a value of greater than 0
•Suggested valued for testing of MaxBSICIdentTime is 3 or 4 seconds if the overall procedure of Hand
•Feature is applicable to both CS and PS connections so parameter is applicable in both RT and NRT FMCG param
mented in the source cell (old serving cell) and numerator is incremented in the target cell (new serving cell).
Determine
###SCC success rate, SCC failure rate and failure cause distribution
Check target
### cells HSDPA Setup performance (M1002C401 – M1002C428) if source
•To find out which target cells are causing the SCC fa
If high SCC_FAILED_due_to_AC
###
•Check target cells M1000C22 AVE_PTXTOT_CLASS
•Check target cells number of simultaneous active HS
If high SCC_FAILED_due_to_BTS
###
•Check target cells M1002C416/424 SETUP_FAIL_BT
•Check target cells CE resource utilisation at BH using
•Check NBAP Radio Link Reconfiguration Failure rate
•Check SHO overhead – all branches must have enou
If high SCC_FAILED_due_to_UE
###
•Check target cells M1002C415/423 SETUP_FAIL_UE
•Check RB reconfiguration Failure rate
•Require ICSU troubleshooting for UE types monitorin
6.If high SCC_FAILED_due_to_TRANS
•Check target cells of M1002C414 SETUP_FAIL_IUB
•Evaluate number of reconfiguration failure due the tra
•Check M1005C128 CANC_ADD_SRNC_TRAN_STP
•Check M1001C531-C533 RAB_STP_FAIL_XXX_IUB
7.If high SCC_FAILED_due_to_Others
•Check RNC internal transport resources usage (DMP
•Require ICSU troubleshooting
ccess Rate, CPICH EcNo Report(in % & no.) - Excellent, good, Acceptable, Poor, Bad
pts & SR, Also their Avg. EcNo & RSCP shown their,
delete/replacement window
> decreased KPIs
problems
timizing the following parameters:
the periodical reports
nt 1C must be set in relation to events 1A and 1B
entWindow increase depends on AddWindow and DeletionWindow sizes
nternally every 200ms

entTime parameter values are 0ms, 240ms, 640ms and above to optimally utilize averaging in the UE
cause delay (for example 320ms compared to 240ms means extra 80ms delay)
orting happens on occasions 0, 200, 400, 600
surements or disable periodicity to make reporting event based

long, each occupying 160-200ms air interface time
too short, the whole UL SRB bandwidth will be easily fully occupied by long measurement reports
crease the interval from 0.5s to 1.0s
BSIC decoding need to be done in target GSM cell for RT
BSIC decoding is not needed for NRT
Cell found ratio for RT tells how easily target cell is found
No Cell found ratio-- should not be greater than 40-50%.
-> PRxTotal, PTxTotal)
-due to BTS/UE reasons--- ISHO is parallel procedure at the same time
R/Adjacency)-- ISHO Adjacencies report

cell is fully Loaded)/TCH failures/2G traffic/2G Hardware Alarm
FMCS parameter set
ble benefit in reducing CM.
MaxBSICIdent= 3sec
eter; RNC adds Power diff(db) to AdjgRxLevMinHO -- 0...43 dBm, step 1 dBm ( set as 30dbm in TMO)
-- for a handover to be possible----- ( set as -95dbm in TMO)
p, (6 in TMO)
Force Decode BSIC feature for NRT

•RAS06 ED2.1 feature
•ISHO success rate improved a lot -> ISHO cell found ratio decrease
er which must be set to ‘on’ to enable the feature across an RNC
on measurements per cell. If during this time no handover succeeded the handover attempt to GSM is finished.
greater than 0
the overall procedure of HandOver to GSM is close to typical value of 10 sec (GsmMeasRepInterval * GsmMaxMeasPeriod); visible benef
both RT and NRT FMCG parameter sets (although BSIC verification is not always required for PS connections)
re cause distribution
401 – M1002C428) if source cells SCC failure rate is high
et cells are causing the SCC failure
000C22 AVE_PTXTOT_CLASS_4 and M1000C20 AVE_PTXTOT_CLASS_3 if SCC failures due to the lack of DL power (SCC_Failed_due_
mber of simultaneous active HSDPA users
002C416/424 SETUP_FAIL_BTS_HS_DSCH_XXX
resource utilisation at BH using M5001 counters for lack of UL return channel resource
nk Reconfiguration Failure rate
– all branches must have enough CE capacity if UE is in SHO when HS-DSCH allocation is started
002C415/423 SETUP_FAIL_UE_HS_DSCH_XXX
tion Failure rate
shooting for UE types monitoring
M1002C414 SETUP_FAIL_IUB_MAC_D_INT or M1002C422 SETUP_FAIL_IUB_MAC_D_BGR

configuration failure due the transmission
ANC_ADD_SRNC_TRAN_STP_FAIL
33 RAB_STP_FAIL_XXX_IUB_AAL2
ansport resources usage (DMPG)

FMCG parameter set
30dbm in TMO)
MaxMeasPeriod); visible benefit in reducing CM.
f DL power (SCC_Failed_due_to_AC) – this is not visible in HSDPA accessibility KPI
Usually operator maintains a list of planned values.
If no planned value exists for a parameter, it can be compared to NSN default value or to the most common value in
ØTarget is to find and correct discrepancies in the parameter settings.
Discrepancy check can be limited to the most important objects
WBTS licenses
-Baseband capacity (license controlled in FlexiBTS up to HW limit)
Number and type of HSDPA schedulers-- HSDPA shared schedular(in TMO)--HSDPA 48 Users per Cell
Number of HSUPA schedulers-- (HSUPA Basic 24 users per BTS enabled in TMO)
-Local cell grouping and capacity allocation between local cell groups
-Cell maximum RF power
-Antenna line properties (MHA gain, feeder loss, RX diversity branch,…)
Check allocation of local cell groups:

• number of cells per LCG
• baseband allocation per LCG
• Is HSUPA enabled in the LCG
Non-optimal LCG allocation can cause unnecessary blocking due to lack of baseband capacity in LCG
or reduced HSUPA performance if unused baseband capacity is allocated to other LCG.
•If shared scheduler is used, the number of schedulers depend on Tcell parameter settings
Tcell (Frame timing offset of a cell)-- WCEL parameter
Each cell in a BTS uses a BTS Frame Number (BFN) counter, which is delayed by a number of chips de
Tcell is used for defining the start of SCH, CPICH, Primary CCPCH and DL Scrambling Code(s)
Group 1: Tcell values 0 (0 chips), 1 (256 chips) and 2 (512 chips)
Group 2: Tcell values 3 (768 chips), 4 (1024 chips) and 5(1280 chips)
Group 3: Tcell values 6 (1536 chips), 7 (1792 chips) and 8 (2048 chips)
Group 4: Tcell values 9 (2304 chips)
Cells composing a Dual Cell HSDPA cell pair must have the same Tcell value.
UE classes –HSDPA category
Majority of the HSDPA UEs are still category 1-6 five code UEs having max 3.6 Mbps throughput
UE classes –HSUPA category

For HSUPA, the majority of the Ues in our Example are Category 5 UEs supporting 2Mbps throughput and 10
Less than 30% of the UEs are category 6 UEs supporting higher uplink bitrates with 2ms TTI.
Propagation delay counters

PRACH Propogation Delay report-- can be used to evaluate how far UEs are from the cell
•Can be used to detect overshooting sites
M1006C169 PRACH_DELAY_RANGE_VALUE Counter can be used to monitor value of WCEL parameter PRACHDelayRang
WCEL parameter PRACHDelayRange
•1 (5 km), 2 (10 km), 3 (20 km), 4 (60 km), 5 (180 km)
Example: Antenna Tilt Excercise – KPIs Used

Three main counters/KPIs was used for selecting the candidates for tilt:
•1) PRACH_distance > 10 km
•2) CSSR_CS (Call set-up success ratio)
•3) RAB_CS_DR (RAB CS drops)
Overshooting WCEL was found based on monitoring

Then decide whether it needs to be dowtilted or neigh
WCEl parameter-- Cell range- 5000, 10000, 20000 (mts) If Cell range is= 5000;
PRACH Propogation Delay report If Cell range is= 10000
Class 0 to Class 20 tak hoti hai If Cell range is= 20000;
PtxCellMax 43 dbm 40 dbm 40 dbm

PtxCPICH 33 dbm 30 dbm 33 dbm
CCCH total 35.5 32.5 35.5
Available HSDPA pwr (W) 16.4 8.2 6.5
Gammafactor 0.5 0.5 0.5
Ptx_Allowed HSDPA (W) 8.2 4.1 3.2
MPO, dB (calculated) 6.1 6.1 2.1
MPO from Nemo 6 6 2
•Reported CQI can be improved by optimisation on DL RF quality and level

–Reported CQI can not be improved by direct parameter changes in NSN RAN
o the most common value in the network.
Any errors or mismatches between planned setup, configured setup, and actual hardware on site ma
WBTS configuration can be checked using WBTS site manager:
PA 48 Users per Cell WBTS configuration files can also be collected using a tool such as FileCollectorTool:
https://twiki.inside.nokiasiemensnetworks.com/bin/view/SEM/CommandlineTools
It collects site configuration data (including commissioning data and licenses) to xml files which can
Collecting the data takes quite long time as the tool automatically logs to every WBTS to copy the da
Example script for WBTS xml file mass analysis:

Output data includes:
BTS configuration (cells, carriers, HSDPA/HSUPA schedulers, …)
BTS HW (system modules, radio modules, WSPx/WPAx/WTRx cards)
BTS licenses
Local cell group configuration
MHA and antenna line data
Check HSDPA scheduler type and number:

HSDPA scheduler type is defined in WBTS commissioning phase or by HSDPA shared scheduler lic
•If shared scheduler is used, the number of schedulers depend on Tcell parameter settings o
Wrong scheduler type may cause HSDPA setup problems due to too many users, or waste baseban
ell parameter settings on the site.
by a number of chips defined by the value of Tcell.

DL Scrambling Code(s) in a cell relative to BFN. The main purpose is to avoid having the overlapping SCHs
ps throughput
2Mbps throughput and 10 ms TTI.

ith 2ms TTI.
Es are from the cell
parameter PRACHDelayRange when the last RRC Connection Request or Cell Update of the measurement interval was received.
Classification criterias in the below table.
found based on monitoring the three main KPIs.

eds to be dowtilted or neighbor relations needs to be modified.
Cell range is= 5000; 5000 21 238.09m 1 class=238.09m

Cell range is= 10000 10000 21 476.19m 1 class=476.19m
Cell range is= 20000; 20000 21 952.38m 1 class=952.38m
•UE estimates CQI using available information on the channel quality.

–RSCP
–Ec/N0
–HSDPA transmit power (signalled to UE)
–Retransmission rate
–Etc.
Impact of PtxCPICH power tuning

Under isolated cell without any other traffic. HSDPA 15 code, 64QAM enabled, Category14 – 64QAM HSDPA UE used
•Both PtxCPICH 33 dBm and PtxCPICH 30 dBm measured. All other parameter remains untouched (PtxCellMax
•While decreasing CPICH tx power by 3 dB (from 33 dBm to 30 dBm)
–Ave reported EcNo decrease ~ 2.5 - 3 dB EcNo degraded
–Ave reported CQI increases only by ~ 1 - 1.5
nges in NSN RAN

and actual hardware on site may lead to performance degradation.
ileCollectorTool:
CommandlineTools
censes) to xml files which can be mass post-processed.
s to every WBTS to copy the data, but it can collect all the files in background without user interaction.
by HSDPA shared scheduler license

on Tcell parameter settings on the site.
many users, or waste baseband capacity if schedulers are underutilized.
ng the overlapping SCHs in different cells belonging to the same BTS. An SCH burst is 256 chips long.
interval was received.
64QAM HSDPA UE used
mains untouched (PtxCellMax was 40 dBm in both cases)
56 chips long.
• Capacity Bottlenecks & Analysis
•Common Channel Load Monitoring- RACH, FACH, SCCPCH & PCH Load
•Air Interface Load Monitoring
–R99 Usage
–UL capacity issues
–HSDPA DL power & Usage
–DL Code Usage
–Number of HSPA Users
•BTS Capacity monitoring
•Smart phones
Overall Flowchart for Capacity Management
RU20 Reporting Suite – Capacity Reports

RU20 full report set contains following capacity reports
•RSRAN068 – RNC Capacity
•RSRAN085 – RNC Capacity Usage
•RSRAN066 – Node B Capacity
•RSRAN067 – Cell Capacity
•RSRAN068 – Iub Capacity
•RSRAN086 – Cell Power
•RSRAN097 – NRT DCH Allocations Statistics
•RSRAN013 – NRT Radio Bearer Statistic
The PRACH preamble load

RACH transport channel may
PRACH load c
•Increasing the
•Increasing the
•Increasing the
•Check whethe
•Evaluate whet
•Upgrading the
RNC_ 978b_AveragePR
RACHCapacity parameter- HW capacity reserved for a RACH transport channel in the BTS.
•RACH Capacity is indicated as the capacity of BTS to decode RACH messages in a 10 ms radio fra
•also Defines the number of PRACH preamble signatures used
•Range 1,2,3,4 (messages) and default = 2
•Recemmended value:4
For example if the RACHCapacity = 2 (default) then it means that the BTS can decode 2 RACH messages in every
S-CCPCH Configuration 1
• In this configuration, PCH Bit R

•PCH is multiplexed with the FAC
•PCH always has priority
•SF64 is required to transfer the
RAS06 and RU10 support a PCH bitrate

• Transport block size of 80 bits & carry a
i.e. single paging record can be broa
–FACH-c and FACH-u load =100 paging records per second
–PCH load =a single cell can thus page maximu
Max PCH Throughput 8 kbps çè max 100
SCCPCH load is used by PS in downlink channel type selection algorithm

Average SCCPCH load-- ratio between the SCCPCH transmission power and the CPICH power.
•incremented when the MAC-c sends to the RRM an internal message (every 20 seconds, including 0.5s sampling
M 1000C 64 AVE_SCCPC H_INC_PCH_LOA

RNC_ 979 a_SCCPCHAv erageLoad 
M 1000C 65 SCCPCH_LOAD_DENOM_0
The load of different transport channels (FACH-u, FACH-c and PCH) can be monitored separately
RNC_2029b FACH-u Load
RNC_2030b FACH-c Load
Paging Types and PCH Load

•When the network needs to contact a certain user a Paging procedure will take place.
•Paging method used depends on RRC state of UE:
–IDLE: Paging Type 1 - over PCH - LA/RA level - CN originated
–Cell/URA-PCH: Paging Type 1 - over PCH - Cell/URA level - CN/RNC origin.
–Cell-DCH/Cell-FACH: Paging Type 2 / over SRB / Cell level
Only Paging Type 1 affects
the PCH Load
Example:
•The average PCH Throughput approaches 7kbps several times per day
•It is a clear symptom of PCH congestion during the traffic peak hour.
•Average PCH Load equal to 80..90% at RNC≡LAC level
•It is a highly congested situation, a high rate of missing pages is expected and LAC splitting needs to be
•The Paging success rate starts to decrease when PCH throughput exceeds 4-4.5kbps, that is a PCH Load
•Threshold of 50% PCH Load confirmed as Rule of Thumb to trigger PCH Load optimization
Paging Load Optimization: LAC splitting

•Enabling a 2nd S-CCPCH without 24 kbps paging channel will not increase the PCH capacity (8kbps), but only FA
•LAC splitting is needed to reduce the Paging Load
Paging Load Optimization: DRX Cycle Length

•DRX Cycle Length changed from 1280ms to 640ms
•Linear region increased from 45% to 58%
Paging Load Optimization: (RU20) 24 kbps Paging Channel

RU20 support PCH bitrate of 8kbps and 24 kbps
–Transport block size of 240 bits & 10 ms TTI
=Up to 8 paging records per TTI allowed (3GPP)
If 1 paging record broadcasted/10ms TTI=100 paging records per second= 1 single cell can
Then for 8 paging records/10ms TTI=1 single cell can page 8*100=800 UEs/sec
Max PCH Throughput 24 kbps çè max 800 Pages/sec per cell
Example: Updating 8 kbps to 24 kbps PCH
Object Parameter Name Abbreviated Name

RNC Low utilization time to trigger of the MAC-d flow MACdflowutilTimetoTrigger
RNC Window size of the MAC-d flow throughput measurement MACdflowthroughputAveWin
RNC Low throughput time to trigger of the E-DCH MAC-d flow EDCHMACdFlowThroughputTim
RNC Window size of E-DCH MAC-d flow throughput measurement EDCHMACdFlowThroughputAve
RNC Uplink traffic volume measurement low threshold TrafVolThresholdULLow
RNC UL/DL activation timer UL_DL_activation_timer
RNC Inactivity timer for uplink 8kbps DCH InactivityTimerUplinkDCH8
PCH loading and FACH throughput

One SCCPCH and 8 kbps PCH Case
When SCCPCH is heavily loaded there is risk that FACH messages are delayed or even dropped. This may cause reconfigur
Paging Parameter Recommendations – 3G
Def/Curr Recom
Parameter Name (Cell level) ent mended
N300 3 2
2000ms
2000ms
T300 (10)
Recomme
Parameter Name (RNC level) Current nded
WaitTimeRRCconversational 3 2
WaitTimeRRCstreaming 3 2
WaitTimeRRCinteractive 5 8
WaitTimeRRCbackground 5 8
WaitTimeRRCsubscribed 3 3
WaitTimeRRCemergency 1 1
WaitTimeRRCinterRATreselectio 3 3
WaitTimeRRCregistration 5 5
WaitTimeRRChighPrioritySignalling 1 2
WaitTimeRRClowPrioritySignalling 5 2
WaitTimeRRCunknown 1 2
WaitTimeRRCother 0 2
Air/Radio Interface Load/Capacity Monitoring-- (R99 Usage, UL Capacity Issues,

•Radio interface monitoring includes resources that cause Admission control to reject establishment of new Conne
–UL Power
–DL Power
–DL Codes
–No. of HSPA users
•When HSPA is enabled in the cell, the DL and UL resources are shared between HSPA and R99 users
–Both R99 and HSPA should be monitored
•Reactive Measurements
–Setup Failures due AC
▪RRC/RAB setup failures
▪PS Call setup failures due AC
–HSDPA setup failures
▪Setup failures due UL DCH
▪Max. Number of HSDPA users reached
–Rejection rates in downlink and uplink
▪SRB, AMR, CS data, PS data, separately for UL and DL
–Low HSDPA throughput
–Channelisation code blocking rate
•Proactive Measurements
–Common channel Load (RACH, FACH, PCH)
–R99 Usage - Overview of cell loading status in UL/DL for R99 traffic only
–HSPA throughput limitations
▪HSPA Power & Usage
–Channelisation Code utilisation
–Simultaneous number of HSDPA users
R99 Usage:
UL Capacity Issues:
•UL admission control start blocking incoming traffic if the RTWP (Received Total Wideband Power) and controlled pa
–For years this has been solved by increasing the targets of the AC but now in 3G
•1 UE transmission interferes the other UEs
–One problematic connection can make the other UEs increasing the tx power and the cell starts b
▪the coverage decreases as the UEs in the cell edge run out of tx power
•The control must be returned to 3G network by decreasing the AC targets and blocking the traffic in a controlled way
System Noise
•System noise (WCEL: PrxNoise) is the sum of all stationary noises;
–thermal noise
–interference caused by spurious emissions of other systems,
–noise caused by additional equipment such as repeaters
•PrxNoise can vary place to place and even time to time
•PrxNoise is a RNP parameter whose setting affects the capacity of cell
–PrxNoise too low: overestimation of cell load and can lead to unnecessary call blocking
–PrxNoise too high: underestimation of cell load and can lead to overload situation
Wrong Prx Noise level causes error to estimated power in PIE (Power Increase Estimation) and PDE (Power Decrease
Autotuning Prx noise:
•PrxNoise is updated by the autotuning algorithm which adjust Prx Noise level automatically. Enabled with Pr
PrxNoise autotuning step sizes is limited by PrxNoiseMaxTuneAbsolute parameter (by default not limited)
•Recommended parameter value is 2 dB. Value 2 dB allows 4 dB range in Prx Noise autotuning functionality
•It is important to verify that prxnoise in the unloaded cell is close to -105 dBm. If that is not the case the cell needs further inve
PrxTarget is defined relative to PrxNoise.
–M1000C12 Maximum PrxNoise Level
–M1000C13 Minimum PrxNoise Level
Uplink Scheduling
RAN capacity management includes three sequential steps:
1.Counter & KPI monitoring with agreed trigger thresholds (daily/weekly) to measure resource usa
2.Detailed Blocking cause analysis & optimisation actions
3.Possible Hardware Capacity upgrade actions & verifications
Capacity upgrade process involves making a decision as to whether an upgrade is required or whether the
If an upgrade is required, upgrade verification is performed once the upgrade has been implemented
CCH Load includes:

–RACH pre-amble
–RACH-c and RACH-u load
–FACH-c and FACH-u load
–PCH load
–SCCPCH power load
CCH load of each cell needs to be measured, for example FACH-c, FACH-u and PCCH transport channels can be m
he PRACH preamble load depends upon the no. of UE making use of RACH transport channel.
ACH transport channel may be used for the transfer of either user plane (RACH-u) or control plane (RACH-c) information.
PRACH load can be reduced by:
•Increasing the number of available PRACH preamble signatures
•Increasing the number of available PRACH access slots
•Increasing the number of available PRACH
•Check whether a large amount of signalling generated by cell, URA, location area or routing area updates. If so, consider a
•Evaluate whether or not there is excessive user plane data transfer within CELL_FACH. If so, consider reducing the RLC b
•Upgrading the BTS configuration in terms of an additional carrier
SUM_RACH_ACK_PREAMB LES •M1000C176

RNC_ 978b_AveragePRACHMessageLoad 
DENOM_RACH _ACK_PREAM BLES •M1000C177
ssages in a 10 ms radio frame
2 RACH messages in every 10ms radio frame
nfiguration 1 S-CCPCH Configuration 2
n this configuration, PCH Bit Rate is limited to PCH bit rate to 8 kbps •PCH24kbpsEnabled is conf
CH is multiplexed with the FACH-u and FACH-c •PCH bit rate is increased to
CH always has priority •PCH is allocated its own sep
F64 is required to transfer the FACH-u and FACH-c bit rates •SF128 is allocated to the PC
RU10 support a PCH bitrate of 8 Kbps RU20 support PCH bitra

block size of 80 bits & carry a single paging record per TTI (10 ms TTI) –Transport bl
aging record can be broadcasted per 10 ms TTI –24kbps pag
cords per second
ll can thus page maximum 100 UEs per second
ughput 8 kbps çè max 100 Pages/s per cell 24Kbps paging Channel - Impact to C
•HSDPA cannot use 15 HS-PD
(B/coz Channelisation code fo
•The transmit power of the S

•PtxSCCPCH1 (P
•PtxSCCPCH2 (S
•PtxSCCPCH3 (S
•PtxSCCPCH2SF
•The PtxSCCPCH2SF128 par
•All parameters define the tr
conds, including 0.5s sampling period) with the common channel information
C H_INC_PCH_LOAD
%
_LOAD_DENOM_0
RAS06 and RU10 support a PCH bitrate of 8 Kbps

• Transport block size of 80 bits & carry a single paging record per TTI (10 ms TTI)
i.e. single paging record can be broadcasted per 10 ms TTI
=100 paging records per second
=a single cell can thus page maximum 100 UEs per second
Max PCH Throughput 8 kbps çè max 100 Pages/sec per cell
In case of too high Paging Load a considerable percentage of paging messages could get lost causing a bad user experience (
e.g. high traffic, LAC oversize,…).
From S-CCPCH Configuration 1, we know that S-CCPCH can be shared with the FACH-c and FACH-u but
It means that high Paging load has an impact upon FACH capacity when single S-CCPCH is configured.
 M 1006 C 25 _ PAGING_TYPE_ 1_ATT_CN_ORIG 

 
Paging Att empts per Cell    M 1006 C 25 PAGING_TYPE_ 1_ATT_RNC_O RIG 
  M 1006 C 27 _ PAGING_TYPE_ 2 _ATT 
 
nd LAC splitting needs to be planned.
-4.5kbps, that is a PCH Load of 50-55% approximately and is below 90% when PCH throughput exceeds 6kbps
d optimization
H capacity (8kbps), but only FACH capacity.
24 kbps Paging Channel feature can increase the paging channel capacity three
So PCH throughput is increased- 24 kbps PCH
When the amount of paging messages exceeds 50% of the nominal capa
second= 1 single cell can page 100 UEs/sec •50 msg/sec for 8 kbps PCH
=800 UEs/sec •250 msg/sec for 24 kbps PCH
Actual
bbreviated Name value new value
ACdflowutilTimetoTrigger 2 sec 0 sec *
ACdflowthroughputAveWin 3 sec 2 sec
DCHMACdFlowThroughputTimetoTrigger 5 sec 1 sec
DCHMACdFlowThroughputAveWin 3 sec 2 sec
rafVolThresholdULLow 128 bytes 256 bytes
L_DL_activation_timer 2 sec 1 sec
activityTimerUplinkDCH8 5 sec 2 sec
d. This may cause reconfiguration process failures and PS RABs drops.

Capacity Issues,
ct establishment of new Connection/bearer
SPA and R99 users
nd Power) and controlled part of UL noise increase too much
he tx power and the cell starts breathing

edge run out of tx power
ic in a controlled way
unnecessary call blocking

to overload situation
) and PDE (Power Decrease Estimation) algorithms, in turn causes power spiking in the uplink spectrum.
utomatically. Enabled with PrxNoiseAutotuning (WCEL)

eter (by default not limited)
x Noise autotuning functionality. In this case PrxNoise should have default value -105 dBm.
case the cell needs further investigation.
•PrxTarget is scheduling target for RT services and also NRT service [when there is not E-DCH connections w
•Prx_Target_PS is used for NRT scheduling when one or more E-DCH connections have been established. Th
PrxMaxTargetBTS is BTS scheduling target for HSUPA. It is suggested to configure this parameter to be greater than PrxTarget +
•NRT PS R99 packet scheduling should be done with target lower than PrxMaxTargetBTS in order to provide capa
•PrxNoise autotuning should be limited
Note: Requires WCEL level check of minimum PrxNoise
Object Parameter Default

WCEL PrxMaxTargetBTS 6 dB
WCEL PrxTarget 4 dB
WCEL PrxTargetPSMin 4 dB
WCEL PrxTargetPSMax 4 dB
RNC PrxNoiseMaxTuneAbsolute not lim
y) to measure resource usage or/and blocking.
e is required or whether the network is likely to benefit from further optimisation.

as been implemented
nsport channels can be multiplexed into same SCCPCH

ACH-c) information.
ea updates. If so, consider adjusting the area boundaries.

onsider reducing the RLC buffer thresholds that trigger the transition to CELL_DCH
Total no. of RACH Frames=RRIndPeriod/Length of 1 RACH Frame

i.e. 200ms/20ms=10
M1000C176 SUM_RACH_ACK_PREAMBLES
M1000C177 DENOM_RACH_ACK_PREAMBLES
nfiguration 2
CH24kbpsEnabled is configured to enabled with this configuration

CH bit rate is increased to 24 kbps
CH is allocated its own separate S-CCPCH
F128 is allocated to the PCH to support the increased bit rate
RU20 support PCH bitrate of 8kbps and 24 kbps

–Transport block size of 240 bits & 10 ms TTI
–24kbps paging channel require activation of second SCCPCH channel
ng Channel - Impact to Code and power capacity
SDPA cannot use 15 HS-PDSCH codes when HSUPA 2 ms TTI is enabled with 24 kbps PCH
coz Channelisation code for 24 kbps PCH uses a larger section of the code tree)
he transmit power of the S-CCPCH is defined using the parameters:

•PtxSCCPCH1 (PCH/FACH or only FACH)
•PtxSCCPCH2 (Standalone PCH)
•PtxSCCPCH3 (S-CCPCH for SAB)
•PtxSCCPCH2SF128 (Standalone PCH SF128 / 24kbps)
he PtxSCCPCH2SF128 parameter defines the transmit power of the S-CCPCH used to transfer the 24 kbps PCH
ll parameters define the transmit power of the data bits (rather than the transmit power of the TFCI and Pilot bits)
record per TTI (10 ms TTI)

er 10 ms TTI
s per second
ing a bad user experience (‘non-reachability’ of UEs due to missing pages).
ACH-c and FACH-u but PCH always has priority.

configured.
ng channel capacity three times higher from the 8 kbps
ds 50% of the nominal capacity, its good time to start thinking about actions to reduce paging channel load to avoid degradation in paging s
is not E-DCH connections with the cell]
s have been established. This can be adjusted between PrxTargetPSMax and PrxTargetPSMin.
be greater than PrxTarget + PrxOffset because the Node B is more responsive than the RNC.
BTS in order to provide capacity for HSUPA users
Recommended
6 - 12 dB
4 - 8 dB
4 - 8 dB
4 - 8 dB
2 dB
o avoid degradation in paging success rate.
1.1.1.1.1. Accessibility Analysis (CS/PS/HS)
CS/PS Access Failure Optimization: Call Setup analysis
HSDPA Access Failure Optimization:
1.1.1.1.1. Retainibility Analysis (CS/PS/HS)

Voice Drop Call Optimization:
1. Monitor Daily Performance Reports/KPIs Worksheet---Pick Worst Offenders
2. Identify DCR top offenders…. few cells?…. Any particular area ? Known Coverage issue? Need a
3. Was the availability of the site 100%?
4. Any current alarms on the site / sector?
5. Check the alarm history especially for transmission issues (NBAP link failures/T1 fluctuations?)
6. Check if the sector is dropping the calls due to RF (Counter: Voice_Drops_due_to_radio_int)
7. If not RF, check if the following counters are pegged:
• Voice Drops due to Iu
• Voice Drops due to BTS
• Voice Drops due to Iur (Not applicable for Cleveland or Columbus now)
• Voice Drops due to RNC
• Voice Drops due to UE
7. If drops are due to RF (Voice Drops due to radio int), check the Site location, Neighbors, Cell to c
8. Need Tilt / Azimuth change to improve the area?
9. HO issue? All Neighbor Exists? SHO….ISHO……IFHO…….?? Neighbor Adds?
10. It might be observed on some sites that although there is no alarm and cell is carrying traffic, som
R99 PS Drop Call Optimization:
2.8.1.2.3 Throughput Optimization:

HSDPA Throughput Optimization:
2.8.1.2.4. Capacity Analysis (Power, Codes, Node-B CE, RNC)
2.8.1.3 UMTS Special Feature Optimization
2.8.1.3.1 Multi Band Load Balancing(MBLB)
Candidates for MBLB are Inter Frequency neighbors on different freq layer, if prioritized hig
· Triggering Events
· Target Layer Selection Criteria
· Handover Execution
1.Four Triggering Events: Radio Bearer Setup, Inactivity in Cell-DCH, State Transition to Cell-DCH, M
2.Four Target Layer Selection Criterion: Freq Layer Preference (based on UE capability, Requeste
3.IFHO Execution: Blind HO (W/o Comp Mode)- (RB Setup Triggered & Transition to DCH state Trigge
Measurement Based HO(With CM) -( Inactivity Timer Triggered & Mobility Trigg
Trigger Events:
Optimization Strategy:
Confirmation to the recommended parameter set in most cases. Some market/Cluster/Site specific ad
Main Parameters to keep Track /Tune and Effects:

1. MBLBRABSetupEnabled; MBLBInactivityEnabled; MBLBStateTransEnabled; MBLBMobil
(Each type can be enabled on cell level independently on others, by corresponding source cell WCEL p
2. Preferred Frequency Layer Identifiers: (Parameters used to create/define the preferred

Example: RNC-1 / PFLIdentifier-1
· LaySelWeightLoad=50
· LaySelWeightRSCP=0
· LaySelWeightPrefLayer= 100
· LaySelWeightBand= 0
· LowLoadPreference = 1
· PreflayerHSDPAxxx=F4
· PrefayerR’99xxx=F3
· PrefayerDCHSCxxx=F1, F2
· PreferBandForLayering=F1,
3. RSCP thresholds used to make upper or lower frequency bands appear more attractive:
BlindHORSCPThrAbove ; BlindHORSCPThrBelow.
4. Weights allocated to each component of the Preference Score calculation

LaySelWeightPrefLayer; LaySelWeightBand; LaySelWeightRSCP; LaySelWeightLoad
5. Whether or not increased weight is given to low loaded cells: LaySelLowLoadPref
6. Preferred layers for fast moving UE: PFLFastMovUECS , PFLFastMovUEPS

2.8.2.2. GSM Optimization Process using OSS KPI/Counters
2.8.2.2..1. Voice Accessibility Analysis (SDCCH/TCH)
Any
NO
alarms in
YES High Access Failure R
problem
1
period
YES
High RACH Failure?
NO
YES
High AG Blocking?
100% NO
Access
failure?
YES
NO
YES
High SDCCH YES

Is cell YES Blocking?
barred?
NO NO
YES
Wrong LAC, YES YES
CI in MSC? High TCH Blocking?
NO
DMAX YES
=0 Modify the parameters accordingly
Escalate to NSN
technical
support
GSM Voice Access Failure Analysis P

2.8.2.2.3 HO Failure Analysis
Check the neighbor list to
High HO Failures
see if any neighbors are
2 missing
NO Any alarms in YES 1

surrounding area?
YES Are HO fails
outgoing?
NO
Check HO Adj Check TCH report

Problem is at report to find to verify if there’ YES
Is HOF due to YES
the target problematic TCH blocking
blocking?
cell relationship
NO
NO
Check the site alarms
Check HO Adj report to (e.g. transmission) of
target and source.
find problematic
relationship
Check if there’s any Check neighbor list

Is the failure YES discrepancy of the -could be the same
100%? neighbor BCCH-BSIC
NO
Check HO cause report 153
Major HO cause Check

if there’s co & Review Freq plan
YES YES
by quality? adj-BCCH interfers
NO NO
Neighbor
optimization (e.g.
HO margin, tilting)
GSM Voice Call Handover Analysis Process

IDD (intelligent DL Diversity)
Downlink diversity means that downlink signal is sent via two separate transceivers, which
IDD method provides its best gain in low-correlated channels. Therefore, phase hopping is used to cha
Both transmitters transmit on the same frequency, but the transmission of secondary transmitter is r
Intelligent downlink diversity (IDD) doesn’t need to be enabled from BSC. It requires re-co
From network side only the master TRX will be seen, the auxiliary TRX will not be seen by
4XUD (Four way UL Diversity)

Four Way Uplink Diversity means that four received signals are combined together by usin
IRC eliminates correlated noise received by both antennas. If no correlated noise exists, IRC behaves l
The combining gain depends on Dominant Interference Ratio and angular spread of Interference Post
Regarding 4UD activation, The 4UD (as well as the IDD) is activated using the BTS manage
The 4UD can only be switched on if the IDD option has been switched on earlier, so 4UD cannot be us
For activating the 4UD feature, in the BSC, the Rx DIV parameter needs to be set to Yes (Y) in order to
SHO overhead RT = 130-199
SHO overhead NRT = 30-45
Poor RAB drop for PS, HSDPA and HSUPA observed for Node B's on ATM
Poor RAB drop rate observed for some sites working on ATM and when the BTS commissioning for these sites were audited it
For signaling and RT services-- the bit rate should be "CBR" (constant bit rate) and for NRT services-- it has to be "UBR+" (u
Initially poor performing sites were identified and rectified accordingly and then all ATM sites were audited for commis
100% HS AFR
The software version was not compatiable with 4 way UL Rx Diversity enabled due to the software gli
Until new version comes:
WCEL - “HSUPA2msTTIenabled” – changed from “Enabled(1)” to Disabled “0”
WCEL - “MaxTotalUplinkSymbolRate” – Changed from 3(5760kbps) to 2(3840 kbps)
Poor ISHO success rate observed for RT

In the compressed mode it is not able to decode the BCCH BSIC or is not able to make accurate decision.
GsmMaxMeasPeriod parameter tuned from 3 Sec’s to 6 Sec’s so that the probability to decode BCCH BSIC of the GSM sites c
The value of GsmMaxMeasPeriod must be greater than the value of GsmNcellSearchPeriod. The value for this parameter was
HSUPA Access Failure Optimization:
Coverage issue? Need a new site ?
ailures/T1 fluctuations?)
ops_due_to_radio_int)
ation, Neighbors, Cell to cell HO statistics, PRACH delay distance and Ec/No quality distribution statistics
cell is carrying traffic, some HW faults ( could be found only during the site visits) causing call drops e.g. bad fee
HSDPA Drop Optimization:

q layer, if prioritized higher than the source cell layer or neighbors in different bands supported by UE The co
e Transition to Cell-DCH, Mobility.

n UE capability, Requested Service, Speed etc), Band Preference, Better Coverage, Traffic/Load Balancing.
sition to DCH state Triggered);
Triggered & Mobility Triggered).
Layer Priority:
t/Cluster/Site specific adjustments needed in order to meet performance KPI and balance traffic between PCS an
sEnabled; MBLBMobilityEnabled
nding source cell WCEL parameter (enabling in target cell not needed)
/define the preferred network layer for each UE capability / service type combination) Up to 8 preferred
pear more attractive:
aySelWeightLoad
SelLowLoadPref
MovUEPS
2.8.2.2.2. Drop Call Analysis (TCH)
Any alarms
gh Access Failure Rate in problem
period
NO
Check if sector is overshooting
NO Is drop due
Check if there’s UL interference to HO?
Check BTS parameters -

maxNumberRetransmission (RET) and YES
nbrOfSlotsSpreadTrans (SLO)
Is drop YES
due to
HO?
Check if combined configuration is used
Check BTS parameters - NO

noOfBlocksForAccessGrant (AG), Set
Is the link YES
AG=0 to make AGCH have higher priority
than PCH balanced?
Check SDCCH capacity

Check if Dynamic SDCCH Allocation
feature is enabled NO
Check if FACCH Call Set Up feature is
enabled
Is UL/DL having
bad quality?
Check TCH capacity
Check and modify HR parameters

NO
Check and modify HO/ADJ parameters
to offload traffic to neighbor cells Is the cell serving
YES
an area it should
not serve?
Is drop due to Abis YES Check T1

or A-if?
NO
Escalate to
YES NSN technical
. Is drop due to TC
support
or others?
ess Failure Analysis Process

1.1.1.1.1. Link Imbalance Analysis:
Use Link Imbalance Report from KPI reports (DL-UL). It is u
IDD/4UD features for DL/UL coverage improvement
1.1.1.2. GSM Special Feature Optimization
· IDD, 4UD, MHA

IDD combined with MHA and 4UD gives best results accord
The MHA and 4UD can improve the performance on highly
· IDD, MHA

Increase HR IDD combined with MHA gives also good results but if the c
penetration
So this configuration is recommended if the cell is 3-5 dB
· IDD, 4UD

IDD improves DL more compared to 4UD on UL. This config
Expected Results:
Drive test
– Bigger coverage area (2-3 dB more in ru
– Better average RxQual (25 % better)
heck neighbor list – Less HO attempts (25 % less) and Cell re
could be the same – Better (E)GPRS data rate
CCH-BSIC
• OSS data
– More traffic (31%)
– Better DCR (0.26%)
– Less HO attempts (~23%)
view Freq plan

ate transceivers, which are fed to separate antennas.
se hopping is used to change phasing between adjacent burst, which decreases correlation between the main an
econdary transmitter is randomly delayed to decrease correlation between the main and secondary transmitters
BSC. It requires re-commissioning of the BTS. During the commissioning with BTS manager softwa
RX will not be seen by BSC.
bined together by using several combining techniques (Interference Rejection Combining (IRC), Max
oise exists, IRC behaves like a normal Maximum Ratio Combiner allowing traffic to flow without requiring noise re
ead of Interference Post Detection Maximum Ratio.
using the BTS manager software during the BTS commissioning. During the commissioning the 4UD
ier, so 4UD cannot be used without IDD.
set to Yes (Y) in order to be able to activate 4UD.

for these sites were audited it was found that the problem was with the bit rate definition for RT and NRT services.
rvices-- it has to be "UBR+" (unspecified bit rate).
tes were audited for commissioning recheck.
d due to the software glitch, temporary solution untill next software load
BCCH BSIC of the GSM sites can be increased

e value for this parameter was changed from 6 to 12 value
ibution statistics
ng call drops e.g. bad feeder or antenna or MHA problem?

supported by UE The complete MBLB feature basically consists of following three operations:
affic/Load Balancing.
IFHO types:
ce traffic between PCS and AWS bands or between multiple carriers within a specific band.
nation) Up to 8 preferred frequencies can be listed for each 16 capability & service combination .
Call Analysis (TCH)
YES High Drop Call Rate

1
Check the severity of

the alarm
Check the fault

situation
YES YES Check transmitter

Is DL
worse?
path including
transmitter.
NO
Check receiver path incl

receiver, cables, MHA,
connectors.
YES Check Rx-level

distribution report
Is bad quality Check idle UL interference

Make due to YES
modification: interference?
Downtilts,
Azimuth, power
adjust
NO
In-band interference?
Check for coverage hole Check frequency plan
Check T1 External interference?
Spectrum Analyzer
Check Receiver
Check TRX .
Escalate to
NSN technical
support
GSM Voice Call Analysis Process

PI reports (DL-UL). It is useful to check if both DL and UL are balanced.
verage improvement etc.
ure Optimization
gives best results according the drive test and OSS data.
e performance on highly unbalanced cells (UL limited) and improve coverage in DL with IDD.
o good results but if the cell is highly unbalanced (UL limited) it could not compensate DL totally (cell will be stil
nded if the cell is 3-5 dB UL limited.
to 4UD on UL. This configuration is recommended if the cell is 1-3 dB UL limited (the gain of 4UD is less in rulal)
e area (2-3 dB more in rural, better indoor, better overlapping in HO)

RxQual (25 % better)
pts (25 % less) and Cell re-selections (24 % less)
data rate
pts (~23%)
tion between the main and auxiliary transmitter.
d secondary transmitters. Phase hopping could increase interference levels.
h BTS manager software the IDD option needs to be switched on.
Combining (IRC), Maximum Ratio Combining (MRC), to get a unique combined signal with better q
without requiring noise reduction.
ommissioning the 4UD feature needs to be switched on.

DL totally (cell will be still UL limited).
in of 4UD is less in rulal).

d signal with better quality.
FMCX
FMCG Parameter
DL DPCH Transmission power Cancellation Offset (db)
DL DPCH Tx Power threshold for AMR (db)
DL DPCH Tx Power threshold for CS (db)
DL DPCH Tx Power threshold for NRT PS (db)
DL DPCH Tx Power threshold for RT PS (db)
GSM HO cause by CPICH EcNo
GSM HO cause by CPICH RSCP
GSM HO cause by DL DPCH TX Power
GSM HO cause by UE TX Power
GSM HO cause by UL DCH Quality
GSM Neighbor Cell Search Period (MEasRep)
IMSI Based GSM HO
ISHO Cancellation cause by CPICH EcNo
ISHO Cancellation cause by CPICH RSCP
ISHO Cancellation cause by DL DPCH TX Power
ISHO Cancellation cause by UE TX Power
Maximum BSIC Identification Time (s)
Maximum Measurement Period (MeasRep)
Maximum Averaging Window (MeasRep)
Measurement reporting Interval
Maximum Interval between Hos (s)
Maximum Interval between Repetitive inter_RAT SLHOs (s)
Minimum measurement Interval (s)
Name
UE TX Power Filter Coefficient
UE Tx Power threshold for AMR (db)
UE Tx Power threshold for CS (db)
UE Tx Power threshold for NRT PS (db)
UE Tx Power threshold for RT PS (db)
UE Tx Power Time Hysteresis
Usage of Directed Retry of AMR call Inter-System Handov
FMCS Parameter
Active Set Weighting coefficient
Addition Reporting Interval
Addition Time
Addition Window (db)
Allow E-DCH usage EcNo offset (db)
change origin
CPICH Ec/No filter Coefficient
CPICH Ec/No HHO Cancellation (db)
CPICH Ec/No HHO Cancellation Time
CPICH Ec/No HHO Threshold (db)
CPICH Ec/No HHO Time Hysteresis
CPICH EcNo offset E-DCH usage Removal (db)
CPICH RSCP HHO Cancellation (db)
CPICH RSCP HHO Cancellation Time
CPICH RSCP filter Coefficient
CPICH RSCP HHO Threshold (db)
CPICH RSCP HHO Time Hysteresis
Detected Set reporting Based HHO
Drop Reporting Interval
Drop Time
Drop Window (db)
IMSI Based SHO
Maximum Active Set Size
Name
Replacement Reporting Interval
Replacement Time
Replacement Window (db)
FMCI Parameter
DL DPCH Tx Power threshold for AMR (db)
DL DPCH Tx Power threshold for CS (db)
DL DPCH Tx Power threshold for NRT PS (db)
DL DPCH Tx Power threshold for RT PS (db)
IFHO cause by CPICH EcNo
IFHO cause by CPICH RSCP
IFHO cause by DL DPCH TX Power
IFHO cause by UE TX Power
IFHO cause by UL DCH Quality
IMSI Based IFHO
Maximum Measurement Period (MeasRep)
MBLB due to Mobility EcNo offset (db)
MBLB due to Mobility RAB Combinations
Maximum Averaging Window (MeasRep)
Measurement reporting Interval
Maximum Interval between Hos (s)
Maximum Interval between Repetitive IF SLHOs (s)
Minimum measurement Interval (s)
Name
Neighbour cell Search Period (MeasRep)
UE TX Power Filter Coefficient
UE Tx Power threshold for AMR (db)
UE Tx Power threshold for CS (db)
UE Tx Power threshold for NRT PS (db)
UE Tx Power threshold for RT PS (db)
UE Tx Power Time Hysteresis
Core PCS Bou
RT NRT HSDPA HSDPA Multi RT
-3
-3
-3
-1
-3
1- Enabled 0- Disabled 0- Disabled 1- Enabled 1- Enabled
1- Enabled
0- Disabled
1- Enabled
0- Disabled
0
0- Not Allowed
1- Enabled
1- Enabled
1- Disabled
1- Enabled
0- Feature not Used 0- Feature not U 0- Feature not U 0- Feature not U 0- Feature not U
6
6
2- 0.5s
10
30
2
8- Approx. 10ms
-3
-3
-1
-3
13- 1280ms
0- Disabled
Core PCS Bou
0
2- 0.5s
11- 320ms
3 3 1.5 3 3
0
3- Apprx. 600ms
-17 -17 -17 -17 -11
13- 1280ms
-19 -19 -19 -19 -13
13- 1280ms 11- 320ms 11- 320ms 13- 1280ms 13- 1280ms
2
-102 -102 -102 -102 -109
13- 1280ms
3- Apprx. 600ms
-105 -105 -105 -105 -112
11- 320ms 11- 320ms 11- 320ms 11- 320ms 12- 640ms
2- Enabled
0- No periodical reporti 2- 0.5s 2- 0.5s 2- 0.5s 0- No periodical
12- 640ms 12- 640ms 12- 640ms 12- 640ms 12- 640ms
6 6 3.5 6 6
0- Not Allowed
3
2- 0.5s
12- 640ms 11- 320ms 11- 320ms 11- 320ms 12- 640ms
6 2.5 1.5 2.5 6
Core PCS Bou

-1
-3
-1
-3
1- Enabled
1- Enabled
0- Disabled
0- Disabled 0- Disabled 0- Disabled 0- Disabled 1- Enabled
0- Disabled
0- Not Allowed
6
2
0- All
6
2- 0.5s
10
30
2
0
8- Approx. 10ms
-3
-3
-1
-3
13- 1280ms
Boundary Core
NRT HSDPA HSDPA Multi RT NRT HSDPA
1- Enabled 1- Enabled 1- Enabled 1- Enabled 0-Disabled 0-Disabled

0-Disabled 1- Enabled 0-Disabled
2 2 0- Feature not U 0- Feature not 2 2
Boundary Core
12- 640ms 12- 640ms

3 0 3 3 3 0
-14 -14 -11 -17 -17 -17
-16 -16 -13 -19 -19 -19

13- 1280ms 13- 1280ms 13- 1280ms 13- 1280ms 11- 320ms 11- 320ms
-112 -112 -109 -112 -112 -112
-115 -115 -112 -115 -115 -115

12- 640ms 13- 1280ms 12- 640ms 11- 320ms 11- 320ms 11- 320ms
2- 0.5s 2- 0.5s 2- 0.5s 0- No periodical2- 0.5s 2- 0.5s

12- 640ms 13- 1280ms 12- 640ms 12- 640ms 12- 640ms 13- 1280ms
6 6 6 6 6 6
11- 320ms 13- 1280ms 11- 320ms 12- 640ms 11- 320ms 13- 1280ms
2.5 3 2.5 6 2.5 3
Boundary Core
1- Enabled 1- Enabled 1- Enabled 0- Disabled 0- Disabled 0- Disabled

HSDPA Multi
1- Enabled
0-Disabled
0- Feature not Used
Core_NRT SHOOverhead Reduction Boundary_NRT SHOOverhea

HSDPA Multi RT NRT HSDPA HSDPA Multi RT
3 2
-17 -17
-19 -19
13- 1280ms 11- 320ms
-112 -112
-115 -115
11- 320ms 11- 320ms
2- 0.5s 2- 0.5s
12- 640ms 12- 640ms
6 4
11- 320ms 11- 320ms

2.5 2
HSDPA Multi
0- Disabled
Boundary_NRT SHOOverhead Reduction
NRT HSDPA HSDPA Multi
-14
-16
13- 1280ms
-112
-115
11- 320ms
2- 0.5s
12- 640ms
4
11- 320ms
2
Parameter Value
DCellHSDPAEnabled Enabled
HSDPA64QAMallowed Enabled
MaxTotalUplinkSymbolRate 5760
HSPDSCHCodeSet 54560
HSUPA2MSTTIEnabled Enabled
DLmaxBitRateSF16 1080 kbps
AMRLCRelatTXWindowRate7Size 512
AMRLCRelatTXWindowRate8Size 750
MaxBitRateNRTMacdflow 0
MaxNbrOfHSSCCHCodes 4
HSPDSCHMarginSF128 2
DPCHOverHSPDSCHThreshold 5
HSPA72UsersEnabled Enabled
HSDPA14MbpsPerUser Enabled
DCellHSDPACapaHO Disabled
FDPCHEnabled Disabled
DCellHSDPAFmcsId #NAME?
FRLCEnabled Enabled
WCEL_AC
WCEL_AC
WCEL_AC
WCEL_AC
wbts
hc
AC
RNFC
WCEL AC AC LC LC PS
Service Affecting Non-Service Aff
Cell DL Power MaxDLPowerCapability PtxCellMax PtxMaxHSDPA PtxTarget PtxOffset PtxTargetPSMax

20W 430 430 430 425 5 420
40W 460 460 460 455 5 450
60W 478 478 478 473 5 468
30W 448 448 448 443 5 438
PS PS WCEL AC
Non-Service Affecting
PtxHighHSDPA PtxPrimaryCPI
PtxTargetPSMin Pwr CH PtxTargetHSDPA
360 425 330 420
390 455 354 450
408 473 354 468
378 443 354 438
DUMP : 6/5/2014 1:52
RNC database Total 1 0

RNC 10 10 0
RNAC 10 10 0
RNFC 10 9 1
RNHSPA 10 0 10
RNMOBI 10 3 7
RNPS 10 7 3
RNRLC 10 10 0
RNTRM 10 8 2
WRAB 25 10 15
WBTS 2937 0 2937
WCEL 13949 6728 7221
WCEL power 13949 3404 10545
WCEL_AC 13949 11979 1850
WCEL_AC power 13949 5167 8662
WCEL_HC common 13949 2439 11510
WCEL_HC MBLB 9174 168 9006
WCEL_HC LTE 8408 8408 0
WCEL_LC 13673 276 0
WCEL_LC power 13952 5177 8652
WCEL_PC 8871 5078 0
WCEL_PS 1256 4787 0
WCEL_PS power 13952 2148 3838
WCEL_SIB common 6225 7724 0
WCEL_SIB MBLB 7619 1555 4775
WCEL_SIB LTE 4104 4304 5541
CLASS Parameters default Celcom
RNAC RNACId 1 1
RNAC AMRLoadTxPower 1 1
RNAC AMRNumofReconf 10 10
RNAC AMRwinSizeSCload 10 10
RNAC AdjustmentPeriod 2 2
RNAC AdjustmentRatio 0 0
RNAC BitRateSetPSNRT 0 0
RNAC DCHSlopeOfTheCurve 2 2
RNAC DLInLoopPCStepSizeCPC 2 2
RNAC DLLoadSource 2 2
RNAC DLmaxBitRateSF128 75 75
RNAC DLpuncturingLimit 5 7
RNAC DownlinkInnerLoopPCStepSize 1 1
RNAC EDCHSlopeOfTheCurve 20 20
RNAC ExpectReorderingPDCP 0 0
RNAC FmaxPeriodPDCP 256 256
RNAC FmaxTimePDCP 5 5
RNAC FreePtxSafetyMarginStr 0 0
RNAC PrachBetaC120 10 10
RNAC PrachBetaD120 15 15
RNAC HSFACHDiscardTimer 2 0
RNAC HSFACHResetTimer 2 0
RNAC HeaderCompressionMethod 0 0
RNAC ICRHostOperatorId 255 0
RNAC LoadBasedAMRCodecMode 0 0
RNAC MaxAdjustmentStep 8 8
RNAC MaxFreezingTime 30 30
RNAC MaxHeaderPDCP 168 168
RNAC MaxNumberOfReAttemptsCong 2 2
RNAC MinPrefChange 3 3
RNAC NonTCPspacePDCP 15 15
RNAC PCPreamble 0 0
RNAC PCrangeDL 15 22
RNAC PeriodULRCAMR 255 10
RNAC PrefSubtract 2 2
RNAC PrxNoiseMaxTuneAbsolute 255 4
RNAC SRBDelay 7 7
RNAC SignallingLinkInactivityTimer 4 4
RNAC StepSizeForDCHBLER 30 30
RNAC StepSizeForEDCHBLER 3 3
RNAC TCPspacePDCP 15 15
RNAC TDMultForHSDPAStreaming 6 6
RNAC TFDCHZeroBitRate 16384 16384
RNAC ULmaxBitRateSF128 30 30
RNAC ULpuncturingLimit 7 7
RNAC UlScrCodeMin 1000000 1000000
RNAC UpLinkInitialTransmitPowerMode 0 0
RNAC UpLinkRecoveryPeriodPowerMode 0 0
RNAC WaitTimeRRCbackground 5 8
RNAC WaitTimeRRCconversational 3 2
RNAC WaitTimeRRCemergency 1 1
RNAC WaitTimeRRChighPrioritySignalling 1 2
RNAC WaitTimeRRCinterRATreselection 3 5
RNAC WaitTimeRRCinteractive 5 8
RNAC WaitTimeRRClowPrioritySignalling 5 2
RNAC WaitTimeRRCother 0 2
RNAC WaitTimeRRCregistration 1 5
RNAC WaitTimeRRCstreaming 3 2
RNAC WaitTimeRRCsubscribed 3 3
RNAC WaitTimeRRCunknown 1 2
RNC CommonMCC 65535 0
RNC CommonMNC 65535 0
RNC CommonMNCLength 0 0
RNC ConnectionRetryCounter 10 10
RNC DLBLERConfInterval 23 23
RNC EmergencyCallRedirectTimer 60 0
RNC ExtendedULDLactivationTmr 0 0
RNC LCSSupportForAnchoring 0 0
RNC LCSfunctionality 0 1
RNC MSActivitySupervision 29 29
RNC N302 7 7
RNC N304 2 2
RNC N308 2 2
RNC PWSMDuration 5 5
RNC PWSMExceededTrafficDur 20 20
RNC PageRep1stInterv 7 7
RNC PageRep2ndInterv 20 20
RNC RANAPprocInitWait 10 30
RNC RTservicesForPS 2 2
RNC RestrictionInterval 60 60
RNC SIB11_priority 4 4
RNC SIB19Priority 3 3
RNC SecOMSIpAddress 0.0.0.0 0.0.0.0
RNC ServingOMS 1 1
RNC ServingOMSAdminSetting 0 0
RNC ServingOMSSwoRequest 0 0
RNC T302 10 12
RNC T304 4 4
RNC T305 3 3
RNC T307 4 4
RNC T308 2 2
RNC T309 8 8
RNC T314 2 2
RNC T316 3 3
RNC T317 4 4
RNC ToAWE_NRT_DCH_tti10 10 7
RNC ToAWE_RT_DCH_tti10 10 10
RNC ToAWE_Speech 5 5
RNC ToAWS_NRT_DCH_tti10 25 15
RNC ToAWS_RT_DCH_tti10 25 25
RNC ToAWS_Speech 15 25
RNC TraceLCSHorizAccur 30 0
RNC TraceLCSPriority 1 0
RNC TraceLCSVertAccur 70 0
RNC TraceLCSWaitPeriod 10 0
RNC ULBLERConfInterval 23 23
RNC UL_DL_activation_timer 2 2
RNC UL_DLcapacityReqWait 10 40
RNC maxCallCapability
RNC maxThroughput
RNFC AMRWithEDCH 0 1
RNFC AMRWithHSDSCH 0 1
RNFC AutomDLPlanUpdEnabled 0 0
RNFC CCCHforCUCallowed 1 1
RNFC CMmasterSwitch 0 0
RNFC CUCforPCHtoDCHallowed 1 1
RNFC CVUserInactInSignConnRel 1 1
RNFC CapaSmartphoneEnabled 0 1
RNFC DCHBitRateBalancing 1 1
RNFC DCHScheOverIur 0 0
RNFC DLOptimisationUsage 1 1
RNFC DynUsageHSDPAReturnChannel 0 1
RNFC EUTRAdetection 0 1
RNFC EmergencyCallISHOSupport 0 0
RNFC EmergencyCallRedirect 0 0
RNFC FRLCEnabled 0 1
RNFC FastDormancyEnabled 1 1
RNFC FlexUpgrUsage 0 1
RNFC HLSModeSelection 0 0
RNFC HSDPA16KBPSReturnChannel 0 1
RNFC HSDPA48UsersEnabled 0 1
RNFC HSDPADynamicResourceAllocation 0 1
RNFC HSDPAMobility 0 1
RNFC HSPAInterRNCMobility 0 2
RNFC HSPAOverIurExt 0 0
RNFC ISHOCancellation 0 1
RNFC ISHOInIurMobility 0 0
RNFC IntelligentEmergencyCallISHOSupport 0 0
RNFC IuPSrelWait3G2GMultiServ 4 4
RNFC MIBPLMNIdIncluded 0 0
RNFC MOCNenabled 0 0
RNFC PBSpolicy 1 1
RNFC PSOpThroUsage 0 15
RNFC PWSMDriftAllowed 0 0
RNFC PostVerifPeriodDLSynch 0 0
RNFC PowerBalancing 0 0
RNFC RABDRAEnabled 0 0
RNFC RRCSetupCCHEnabledR99 0 1
RNFC SLHOCmAllowedNRT 1 1
RNFC SignConnActivitySupervision 4 4
RNFC WPSCallRestriction 0 0
RNFC WireLessPriorityService 0 0
RNHSPA WeightForARP1 100 100
RNHSPA ATOSRBsOnHSPA 30 30
RNHSPA N10msCPCOptObjective 1 1
RNHSPA N10msCQIDTXTimer 7 7
RNHSPA N10msCQIFeedbackCPC 4 4
RNHSPA N10msInacThrUEDRXCycle 7 7
RNHSPA N10msInacThrUEDTXCycl2 3 3
RNHSPA N10msMACDTXCycle 1 1
RNHSPA N10msMACInacThr 0 0
RNHSPA N10msUEDPCCHburst1 0 0
RNHSPA N10msUEDRXCycle 2 2
RNHSPA N10msUEDTXCycle1 2 2
RNHSPA N10msUEDTXLongPreamble 1 1
RNHSPA N2msCPCOptObjective 1 1
RNHSPA N2msCQIDTXTimer 7 7
RNHSPA N2msCQIFeedbackCPC 3 3
RNHSPA N2msInacThrUEDRXCycle 7 7
RNHSPA N2msInacThrUEDTXCycl2 5 5
RNHSPA N2msMACDTXCycle 3 3
RNHSPA N2msMACInacThr 0 0
RNHSPA N2msUEDRXCycle 2 2
RNHSPA N2msUEDTXLongPreamble 1 1
RNHSPA S10msCPCOptObjective 1 1
RNHSPA S10msCQIDTXTimer 7 7
RNHSPA S10msCQIFeedbackCPC 4 4
RNHSPA S10msInacThrUEDRXCycle 7 7
RNHSPA S10msInacThrUEDTXCycl2 3 3
RNHSPA S10msMACDTXCycle 1 1
RNHSPA S10msMACInacThr 0 0
RNHSPA S10msUEDPCCHburst1 0 0
RNHSPA S10msUEDRXCycle 2 2
RNHSPA S10msUEDTXCycle1 2 2
RNHSPA S10msUEDTXLongPreamble 1 1
RNHSPA S2msCPCOptObjective 1 1
RNHSPA S2msCQIDTXTimer 7 7
RNHSPA S2msCQIFeedbackCPC 3 3
RNHSPA S2msInacThrUEDRXCycle 7 7
RNHSPA S2msInacThrUEDTXCycl2 5 5
RNHSPA S2msMACDTXCycle 3 3
RNHSPA S2msMACInacThr 0 0
RNHSPA S2msUEDRXCycle 2 2
RNHSPA S2msUEDTXLongPreamble 1 1
RNHSPA V10msCPCOptObjective 1 1
RNHSPA V10msCQIDTXTimer 6 6
RNHSPA V10msCQIFeedbackCPC 4 4
RNHSPA V10msInacThrUEDRXCycle 6 6
RNHSPA V10msInacThrUEDTXCycl2 2 2
RNHSPA V10msMACDTXCycle 1 1
RNHSPA V10msMACInacThr 4 4
RNHSPA V10msUEDPCCHburst1 0 0
RNHSPA V10msUEDRXCycle 1 1
RNHSPA V10msUEDTXCycle1 2 2
RNHSPA V10msUEDTXLongPreamble 1 1
RNHSPA V2msCPCOptObjective 1 1
RNHSPA V2msCQIDTXTimer 6 6
RNHSPA V2msCQIFeedbackCPC 3 3
RNHSPA V2msInacThrUEDRXCycle 6 6
RNHSPA V2msInacThrUEDTXCycl2 4 4
RNHSPA V2msMACDTXCycle 3 3
RNHSPA V2msMACInacThr 0 0
RNHSPA V2msUEDRXCycle 1 1
RNHSPA V2msUEDTXLongPreamble 1 1
RNHSPA CPICHECNOSRBHSPA -6 -6
RNHSPA CPICHECNOThreEDCH2MS -6 -6
RNHSPA CPICHRSCPThreEDCH2MS 136 136
RNHSPA CPICHRSCPThreSRBHSDPA -103 -103
RNHSPA DCellVsMIMOPreference 0 0
RNHSPA DiscardTimerHSCSVoice 2 0
RNHSPA EDCHCTSwitchGuardTimer 4 4
RNHSPA EDCHMACdFlowThroughputAveWin 6 4
RNHSPA EDCHMACdFlowThroughputRelThr 1 1
RNHSPA EDCHMACdFlowThroughputTimetoTrigger 25 10
RNHSPA EDCHMACdflowtputStrTtT 25 25
RNHSPA EDCHMaxHARQReTxStr 3 3
RNHSPA EDCHMaxHarqReTxSRB 3 3
RNHSPA EDCHMaxHarqReTxSRB2MS 4 4
RNHSPA EDCHMaxNumberOfHARQReTx 3 3
RNHSPA EDCHQOSClasses 63 15
RNHSPA EnablDelayHHO 6 6
RNHSPA EnablDelayStand 5 5
RNHSPA FDPCHAllocMinInterval 3 3
RNHSPA FDPCHAndSRBOnHSPATC 127 127
RNHSPA FDPCHSetupEC 4065 4065
RNHSPA FactorEDCHMaxBRPSstream 18 18
RNHSPA FactorEDCHMaxBitRate 15 15
RNHSPA FactorEDCHMaxBitRate2NRT 14 16
RNHSPA FactorEDCHMaxBitRate3NRT 13 17
RNHSPA HSDPACPICHCTSRepPer 2 2
RNHSPA HSDPACPICHEcNoThreshold -10 -18
RNHSPA HSDPACellChangeRepetitionTime 10 10
RNHSPA HSDPAChaTypeSwitchWindow 0 0
RNHSPA HSDPAInitialBRULStrNRT 3 3
RNHSPA HSDPAMaxCellChangeRepetition 4 4
RNHSPA HSDPAMinBRULStrNRT 3 3
RNHSPA HSDPAPeakRateLimitRABMax 1 1
RNHSPA HSDPAPriority 1 1
RNHSPA HSDPARRCdiversity 1 1
RNHSPA HSDPASRBWindow 2 2
RNHSPA HSDPAinitialBitrateUL 3 1
RNHSPA HSDPAminAllowedBitrateUL 3 1
RNHSPA HSDSCHCTSwitchGuardTimer 5 5
RNHSPA HSDSCHGuardTimerLowThroughput 30 0
RNHSPA HSDSCHQoSclasses 63 15
RNHSPA NBRForPri0DL 0 0
RNHSPA NBRForPri0UL 0 0
RNHSPA HSPDSCHAdjustPeriod 10 5
RNHSPA HappyBitDelayConditionEDCH 3 3
RNHSPA HsdschGuardTimerHO 5 5
RNHSPA InacUserNbrXXXOverNRT 2 2
RNHSPA InacUsersOverloadFact 90 90
RNHSPA InactCPCBatOptT 0 36
RNHSPA InactCPCNoBatOptT 48 48
RNHSPA InactNonCPCBatOptT 0 0
RNHSPA InactNonCPCNoBatOptT 0 0
RNHSPA MACdflowthroughputAveWin 6 4
RNHSPA MACdflowthroughputRelThr 0 0
RNHSPA MACdflowthroughputTimetoTrigger 25 0
RNHSPA MACdflowtputStrTtT 25 25
RNHSPA MACdflowutilRelThr 1 1
RNHSPA MACdflowutilStrTtT 10 10
RNHSPA MACdflowutilTimetoTrigger 0 0
RNHSPA MaxBitRateNRTMACDFlow 0 0
RNHSPA MaxCSDelayRNCETTI10 5 0
RNHSPA MaxCSDelayRNCETTI2 8 0
RNHSPA MaxCSDelayUE 6 0
RNHSPA MaxEHARQReTxCSAMR10 1 0
RNHSPA MaxEHARQReTxCSAMR2 2 0
RNHSPA MaxReWaitTime 32 32
RNHSPA MaxReWaitTime2msTTI 60 60
RNHSPA MaxReWaitTime2msTTI16 60 0
RNHSPA MaxReWaitTimeRT 10 10
RNHSPA MaxSetOfEDPDCHCSAMR10 0 0
RNHSPA MaxSetOfEDPDCHCSAMR2 0 0
RNHSPA NRTRBBRWithEDCHStr 1 1
RNHSPA PeriodicityForSI 6 6
RNHSPA PowerOffsetEHARQVoice 0 0
RNHSPA PowerOffsetForSI 3 3
RNHSPA T1HSCSVoice 1 0
RNHSPA T1HSFACH 1 0
RNHSPA TGPLAMRHSDPAInterFreq 4 4
RNHSPA TGPLHSDPAInterFreq 4 4
RNHSPA ThresholdMaxEDPDCHSR1920kbps 16 16
RNHSPA UPResAllocInCellDCHWait 3 3
RNHSPA WeightDCHBG 15 15
RNHSPA WeightDCHTHP1 90 90
RNHSPA WeightHSPABG 25 25
RNHSPA WeightHSPATHP1 100 100
RNMOBI AnchorFmciIdentifier 0 0
RNMOBI AnchorFmcsIdentifier 0 0
RNMOBI AnchorHopiIdentifier 0 0
RNMOBI AnchorHopsIdentifier 0 0
RNMOBI CellReselectionObservingTime 16 16
RNMOBI DRRCForHSDPALayerServices 204 524
RNMOBI DefaultAuthorisedNetworkId 0 0
RNMOBI DirectedRRCForHSDPALayerEnhanc 0 1
RNMOBI DisablePowerInHSDPALayeringDecision 0 0
RNMOBI EcnoDifferenceThreshold 16 16
RNMOBI EnableULQualDetRep 0 1
RNMOBI FastDormOverCpcPri 0 0
RNMOBI FastUECancel 1 1
RNMOBI FastUEPeriod 10 10
RNMOBI FastUEThreshold 3 3
RNMOBI GANetwARFCN 65535 0
RNMOBI GANetwBCC 255 0
RNMOBI GANetwNCC 255 0
RNMOBI GapPositionSingleFrame 4 4
RNMOBI GsmHandoverAMR 1 1
RNMOBI GsmHandoverCS 0 0
RNMOBI GsmHandoverNrtPS 0 1
RNMOBI GsmHandoverRtPS 0 0
RNMOBI HSCAHORabCombSupport 1 1
RNMOBI HSDPACPICHAveWindow 3 3
RNMOBI HSDPACPICHReportPeriod 1 1
RNMOBI HSDPACellChangeMinInterval 3 3
RNMOBI HSDPALayerLoadShareThreshold 3 3
RNMOBI HSDPASIRErrorAveWindow 3 3
RNMOBI HSDPASIRErrorFilterCoefficient 5 5
RNMOBI HSDPASIRErrorReportPeriod 1 1
RNMOBI HSDPASIRErrorServCell -6 -14
RNMOBI HSDPASIRErrorTargetCell -4 -12
RNMOBI HSDPAServCellWindow 4 4
RNMOBI HSPADRNCEcNoOffset 6 6
RNMOBI HSPADRNCSIRErrorOffset 6 6
RNMOBI IBTSRabCombSupport 1 0
RNMOBI LHOMinNrtDchAllocTime 20 20
RNMOBI LowerRxTxTimeDiff 874 874
RNMOBI MBLBGuardTimer 10 10
RNMOBI MaxCellReselections 3 0
RNMOBI MaxNumISHOClPerAS 1 1
RNMOBI MultipleBSICIdent 0 1
RNMOBI NCHOFilterCoeffComLoadMeasDRNCCell 15 15
RNMOBI NCHOHystComLoadMeasDRNCCell 300 300
RNMOBI NCHOThrComLoadMeasDRNCCell 70 70
RNMOBI PreferBandForLayering 0 1
RNMOBI RANAPCause1LoadHO 43 43
RNMOBI RANAPCause1ServHO 41 41
RNMOBI SLHOHandlingOfCellLoadMeasNotAct 0 0
RNMOBI SLHOProfileBackgroundPSNRTData 0 4
RNMOBI SLHOProfileConvCSSpeech 0 4
RNMOBI SLHOProfileConvCSTData 0 0
RNMOBI SLHOProfileConvPSRTData 0 0
RNMOBI SLHOProfileConvPSSpeech 0 0
RNMOBI SLHOProfileInteractivePSNRTData 0 0
RNMOBI SLHOProfileStreamCSNTData 0 0
RNMOBI SLHOProfileStreamPSRTData 0 0
RNMOBI SLHOUseBackgroundPSNRTData 0 3
RNMOBI SLHOUseConvCSSpeech 0 3
RNMOBI SLHOUseConvCSTData 0 0
RNMOBI SLHOUseConvPSRTData 0 0
RNMOBI SLHOUseConvPSSpeech 0 0
RNMOBI SLHOUseInteractivePSNRTData 0 0
RNMOBI SLHOUseStreamCSNTData 0 0
RNMOBI SLHOUseStreamPSRTData 0 0
RNMOBI ServBtwnHSDPALayers 3 3
RNMOBI ServicesToHSDPALayer 0 1
RNMOBI TGPLdoubleframeNRTPSgsm 4 4
RNMOBI TGPLdoubleframeNRTPSinterFreq 4 4
RNMOBI TGPLsingleframeAMRgsm 4 4
RNMOBI TGPLsingleframeAMRinterFreq 4 4
RNMOBI TGPLsingleframeCSgsm 4 4
RNMOBI TGPLsingleframeCSinterFreq 4 4
RNMOBI TGPLsingleframeNRTPSgsm 4 4
RNMOBI TGPLsingleframeNRTPSinterFreq 4 4
RNMOBI TGPLsingleframeRTPSgsm 4 4
RNMOBI TGPLsingleframeRTPSinterFreq 4 4
RNMOBI TRelocOverall 8 8
RNMOBI TRelocPrep 6 6
RNMOBI UEQualityRepInterv 4 4
RNMOBI UETxPowerMaxRef 24 24
RNMOBI ULQualDetRepThreshold 1 1
RNMOBI UpperRxTxTimeDiff 1174 1174
RNPS ActivationTimeOffset 300 500
RNPS CellDCHtestTmr 0 0
RNPS CrQueuingTimeDL 4 4
RNPS CrQueuingTimeUL 4 4
RNPS DCHUtilBelowDowngradeThr 6 6
RNPS DCHUtilHighAveWin 100 100
RNPS DCHUtilHighBelowNRTDataRateThr 6 6
RNPS DCHUtilHighTimeToTrigger 20 20
RNPS DCHUtilLowerAveWin128 200 100
RNPS DCHUtilLowerDowngradeThr128 16 64
RNPS DCHUtilLowerTimeToTrigger128 140 80
RNPS DCHUtilMeasGuardTime 6 2
RNPS DCHUtilRelAveWin 100 100
RNPS DCHUtilRelThrDL 8 8
RNPS DCHUtilRelThrUL 8 8
RNPS DCHUtilRelTimeToTrigger 20 20
RNPS DCHUtilUpperAveWin128 200 100
RNPS DCHUtilUpperDowngradeThr128 64 64
RNPS DCHUtilUpperTimeToTrigger128 400 200
RNPS DLOptimisationProhibitTime 2 2
RNPS DLOptimisationPwrOffset 20 20
RNPS FactorMinPBSinterval 2 2
RNPS HSFACHDiscardTimerDTCH 8 0
RNPS HSFACHRestTimerDTCH 2 0
RNPS ICRDowngradeDelayTimer 3 0
RNPS InactDetForStreamingRB 1 1
RNPS InactivityTimerDownlinkDCH128 2 2
RNPS InactivityTimerUplinkDCH128 2 2
RNPS IurPriority 0 0
RNPS PriForBackARP1 0 3
RNPS PriForConvOnHSPA 14 14
RNPS PriForHSFACHDTCH 0 0
RNPS PriForIntSignaling 12 12
RNPS PriForIntTHP1ARP1 11 11
RNPS PriForSRBsOnHSPA 15 15
RNPS PriForStreamARP1 13 13
RNPS RTOverNRTPriThresholdARP1 11 11
RNPS ToCellFACHinTest 1 1
RNPS TrafVolPendingTimeDL 200 400
RNPS TrafVolPendingTimeUL 200 400
RNPS TrafVolThresholdDLHigh 7 7
RNPS TrafVolThresholdDLHighDCH128 8 8
RNPS TrafVolThresholdULHigh 7 4
RNPS TrafVolThresholdULHighDCH128 8 8
RNPS TrafVolThresholdULLow 128 512
RNPS TrafVolTimeToTriggerDL 0 0
RNPS TrafVolTimeToTriggerUL 0 0
RNPS ULLoadStateTTT 4 4
RNRLC AMRLCBufMaxOverbook2NRT 13 13
RNRLC AMRLCBufMaxOverbook3NRT 18 18
RNRLC AMRLCHSFACHPSMaxDAT 15 0
RNRLC AMRLCHSFACHPSMaxMRW 12 0
RNRLC AMRLCHSFACHPSMaxRST 12 0
RNRLC AMRLCHSFACHPSPeriodMax 200 0
RNRLC AMRLCHSFACHPSPeriodMin 4 0
RNRLC AMRLCHSFACHPSPollPDU 23 0
RNRLC AMRLCHSFACHPSPollSDU 1 0
RNRLC AMRLCHSFACHPSPollWin 70 0
RNRLC AMRLCHSFACHPSTriggers 5940 0
RNRLC AMRLCRespHSFACHandRACH 50 0
RNRLC HSFACHAMRLCRespHSRACH 50 0
RNRLC AMRLCMaximumBufferUE100 25 25
RNRLC AMRLCMaximumBufferUE1k 200 125
RNRLC AMRLCmaximumBufferUE400 70 70
RNRLC AMRLCOnDCHOfNRTPSCount 10 10
RNRLC AMRLCOnDCHOfNRTPSFilterReTX 80 80
RNRLC AMRLCOnDCHOfNRTPSMaxDAT 15 15
RNRLC AMRLCOnDCHOfNRTPSMaxMRW 12 12
RNRLC AMRLCOnDCHOfNRTPSMaxRST 12 24
RNRLC AMRLCOnDCHOfNRTPSPeriodMax 140 300
RNRLC AMRLCOnDCHOfNRTPSPeriodMin 4 4
RNRLC AMRLCOnDCHOfNRTPSPollPDU 23 23
RNRLC AMRLCOnDCHOfNRTPSPollSDU 1 1
RNRLC AMRLCOnDCHOfNRTPSPollWindow 70 70
RNRLC AMRLCOnDCHOfNRTPSTriggers 56849 24081
RNRLC AMRLCOnDCHOfSRB136MaxDAT 40 40
RNRLC AMRLCOnDCHOfSRB136PeriodMax 100 100
RNRLC AMRLCOnDCHOfSRB136PeriodMin 4 4
RNRLC AMRLCOnDCHOfSRB136PollPDU 23 23
RNRLC AMRLCOnDCHOfSRB136PollSDU 1 1
RNRLC AMRLCOnDCHOfSRB136PollWindow 70 70
RNRLC AMRLCOnDCHOfSRB136Triggers 1988 1988
RNRLC AMRLCOnDCHOfSRB34MaxDAT 30 30
RNRLC AMRLCOnDCHOfSRB34PeriodMax 112 112
RNRLC AMRLCOnDCHOfSRB34PeriodMin 4 4
RNRLC AMRLCOnDCHOfSRB34PollPDU 23 23
RNRLC AMRLCOnDCHOfSRB34PollSDU 1 1
RNRLC AMRLCOnDCHOfSRB34PollWindow 70 70
RNRLC AMRLCOnDCHOfSRB34Triggers 1988 1988
RNRLC AMRLCOnDCHOfStreamCount 10 10
RNRLC AMRLCOnDCHOfStreamDiscardTime 20 20
RNRLC AMRLCOnDCHOfStreamFilterReTX 80 80
RNRLC AMRLCOnDCHOfStreamMaxDAT 15 15
RNRLC AMRLCOnDCHOfStreamMaxMRW 12 12
RNRLC AMRLCOnDCHOfStreamMaxRST 12 12
RNRLC AMRLCOnDCHOfStreamPeriodMax 140 140
RNRLC AMRLCOnDCHOfStreamPeriodMin 4 4
RNRLC AMRLCOnDCHOfStreamPollPDU 23 23
RNRLC AMRLCOnDCHOfStreamPollSDU 1 1
RNRLC AMRLCOnDCHOfStreamPollWindow 70 70
RNRLC AMRLCOnDCHOfStreamTriggers 32273 15889
RNRLC AMRLCOnEDCHOfNRTPSCount 10 10
RNRLC AMRLCOnEDCHOfNRTPSMaxDAT 15 15
RNRLC AMRLCOnEDCHOfNRTPSMaxMRW 12 12
RNRLC AMRLCOnEDCHOfNRTPSMaxRST 12 24
RNRLC AMRLCOnEDCHOfNRTPSPeriodMax 200 300
RNRLC AMRLCOnEDCHOfNRTPSPeriodMin 4 4
RNRLC AMRLCOnEDCHOfNRTPSPollPDU 23 23
RNRLC AMRLCOnEDCHOfNRTPSPollSDU 1 1
RNRLC AMRLCOnEDCHOfNRTPSPollWindow 70 70
RNRLC AMRLCOnEDCHOfNRTPSTriggers 3857 3857
RNRLC EDCHStrPSCount 10 10
RNRLC EDCHStrPSDiscardTime 20 20
RNRLC EDCHStrPSMaxDAT 15 15
RNRLC EDCHStrPSMaxMRW 12 12
RNRLC EDCHStrPSMaxRST 12 12
RNRLC EDCHStrPSPeriodMax 200 200
RNRLC EDCHStrPSPeriodMin 4 4
RNRLC EDCHStrPSPollPDU 23 23
RNRLC EDCHStrPSPollSDU 1 1
RNRLC EDCHStrPSPollWindow 70 70
RNRLC EDCHStrPSTriggers 3601 3601
RNRLC AMRLCOnFACHOfPSMaxDAT 15 15
RNRLC AMRLCOnFACHOfPSMaxMRW 12 12
RNRLC AMRLCOnFACHOfPSMaxRST 12 12
RNRLC AMRLCOnFACHOfPSPeriodMax 200 200
RNRLC AMRLCOnFACHOfPSPeriodMin 4 4
RNRLC AMRLCOnFACHOfPSPollPDU 23 23
RNRLC AMRLCOnFACHOfPSPollSDU 1 1
RNRLC AMRLCOnFACHOfPSPollWindow 70 70
RNRLC AMRLCOnFACHOfPSTriggers 6100 6100
RNRLC AMRLCOnFACHOfSRBMaxDAT 30 30
RNRLC AMRLCOnFACHOfSRBPeriodMax 200 200
RNRLC AMRLCOnFACHOfSRBPeriodMin 4 4
RNRLC AMRLCOnFACHOfSRBPollPDU 23 23
RNRLC AMRLCOnFACHOfSRBPollSDU 1 1
RNRLC AMRLCOnFACHOfSRBPollWindow 70 70
RNRLC AMRLCOnFACHOfSRBTriggers 1988 1988
RNRLC AMRLCOnHSDSCHOfNRTPSCount 10 10
RNRLC AMRLCOnHSDSCHOfNRTPSFilterReTX 66 66
RNRLC AMRLCOnHSDSCHOfNRTPSMaxDAT 15 15
RNRLC AMRLCOnHSDSCHOfNRTPSMaxMRW 12 12
RNRLC AMRLCOnHSDSCHOfNRTPSMaxRST 12 24
RNRLC AMRLCOnHSDSCHOfNRTPSPeriodMax 200 300
RNRLC AMRLCOnHSDSCHOfNRTPSPeriodMin 4 4
RNRLC AMRLCOnHSDSCHOfNRTPSPollPDU 23 23
RNRLC AMRLCOnHSDSCHOfNRTPSPollSDU 1 1
RNRLC AMRLCOnHSDSCHOfNRTPSPollWindow 70 70
RNRLC AMRLCOnHSDSCHOfNRTPSTriggers 122385 24337
RNRLC HSDSCHStrDiscardTime 20 20
RNRLC HSDSCHStrPSCount 10 10
RNRLC HSDSCHStrPSFilterReTX 66 66
RNRLC HSDSCHStrPSMaxDAT 15 15
RNRLC HSDSCHStrPSMaxMRW 12 12
RNRLC HSDSCHStrPSMaxRST 12 12
RNRLC HSDSCHStrPSPeriodMax 200 200
RNRLC HSDSCHStrPSPeriodMin 4 4
RNRLC HSDSCHStrPSPollPDU 23 23
RNRLC HSDSCHStrPSPollSDU 1 1
RNRLC HSDSCHStrPSPollWindow 70 70
RNRLC HSDSCHStrPSTriggers 65041 16145
RNRLC AMRLCRelatTXWindowRate1 1 1
RNRLC AMRLCRelatTXWindowRate1Size 2 2
RNRLC AMRLCRespTimeDCH10 10 10
RNRLC AMRLCRespTimeDCHRevHSDSCH 14 14
RNRLC AMRLCRespTimeRevEDCH 10 10
RNRLC AMRLCRespTimeEDCH 10 10
RNRLC AMRLCRespTimeFACHAndRACH 50 50
RNRLC AMRLCRespTimeHSDSCHRevDCH 10 15
RNRLC AMRLCRespTimeHSDSCHRevEDCH 10 15
RNRLC AMRLCRespTimeSRBHSPA 10 10
RNRLC AMRLCSRBHSPAMaxDAT 30 30
RNRLC AMRLCSRBHSPAPeriodMax 116 116
RNRLC AMRLCSRBHSPAPeriodMin 4 4
RNRLC AMRLCSRBHSPAPollPDU 23 23
RNRLC AMRLCSRBHSPAPollSDU 1 1
RNRLC AMRLCSRBHSPAPollWindow 70 70
RNRLC AMRLCSRBHSPATriggers 1988 1988
RNRLC AMRLCTXWindowSizeSRB2 2 2
RNRLC PDUSizeBitRateThr 3584 3584
RNRLC PDUSizeCodeThreshold 10 5
RNRLC PDUSizeSIRThr 90 90
RNRLC SDUdiscardModeRTPS 1 0
RNRLC UMRLCEVoiceDiscardTime 10 0
RNTRM Af122AMRDL 60 60
RNTRM Af122AMRUL 60 60
RNTRM Af59AMRDL 60 60
RNTRM Af59AMRUL 60 60
RNTRM Af144CSStreDL 100 100
RNTRM Af144CSStreUL 100 100
RNTRM Af576CSStreDL 100 100
RNTRM Af576CSStreUL 100 100
RNTRM Af64CSConDL 100 100
RNTRM Af64CSConUL 100 100
RNTRM Af128And136DCCHDL 8 8
RNTRM Af128And136DCCHUL 8 8
RNTRM AfFACHCCDL 10 10
RNTRM AfFACHCIDL 10 10
RNTRM AfFACHContUL 10 10
RNTRM AfFACHSDL 10 10
RNTRM AfFACHUDL 10 10
RNTRM AfRACH208UL 10 10
RNTRM AfRACHContDL 10 10
RNTRM AfRTHSDPA 100 100
RNTRM AfRTHSUPA 100 100
RNTRM AfSRBOnHSDPA 1 1
RNTRM AfSRBOnHSUPA 1 1
RNTRM Af128NRTDCHDL 100 60
RNTRM Af128NRTDCHUL 100 60
RNTRM AfPCHContUL 10 10
RNTRM AfPCHDL 10 10
RNTRM Af128RTPSAMDL 100 100
RNTRM Af128RTPSAMUL 100 100
RNTRM Af128RTPSUMDL 100 100
RNTRM Af128RTPSUMUL 100 100
RNTRM EchoRequestSending 0 0
RNTRM HSDPAFlowControlLowThresholdDedicatedVCC 35 35
RNTRM HSDPAFlowControlLowThresholdSharedVCC 35 35
RNTRM HSDPAFlowControlTargetDelayDedicatedVCC 205 205
RNTRM HSDPAFlowControlTargetDelaySharedVCC 205 205
RNTRM IPStackErrorTimer 30 30
RNTRM IuDATree 3 3
RNTRM IubDATree 1 1
RNTRM IurDATree 2 2
RNTRM N3Requests 5 5
RNTRM NRTDCHFlowControlTargetDelay 100 100
RNTRM SignallingToDSCP 34 34
RNTRM T3Response 10 10
RNTRM THP1DelaySensitivitySwitch 0 0
RNTRM ToAWEOffsetForOverbook 10 10
RNTRM ToAWSOffsetForOverbook 100 100
RNTRM ULCACSwitch 2 2
RNTRM UsedSRBALCSet 3 3
WRAB DeltaSIRAfterDownlink 7 7
WRAB DeltaSIRAfterUplink 7 7
WRAB DeltaSIRDownlink 15 15
WRAB DeltaSIRUplink 15 15
WRAB DownlinkOrthog 50 50
WRAB EDCHBLERAdjCSVoice10 1
WRAB EDCHBLERAdjCSVoice2 2
WRAB EbNoDCHOfPSNRTPriQua -20 -20
WRAB EbNoDCHOfPSNRTPrim 80 80
WRAB EbNoDCHOfPSNRTSec 65 65
WRAB EbNoDCHOfPSNRTSecQua -13 -13
WRAB EbNoDCHOfPSNRTSelQuaDL 127 127
WRAB EbNoDCHOfPSNRTSelQuaUL 127 127
WRAB EbNoDCHOfPSStrPriQua -20 -20
WRAB EbNoDCHOfPSStrPrim 80 80
WRAB EbNoDCHOfPSStrSec 65 65
WRAB EbNoDCHOfPSStrSecQua -13 -13
WRAB EbNoDCHOfPSStrSelQuaDL 63 63
WRAB EbNoDCHOfPSStrSelQuaUL 31 31
WRAB EbNoDCHOfSRB136 80 100
WRAB EbNoDCHOfSRB136Qua -20 -20
WRAB EbNoDCHOfSRB34 80 100
WRAB EbNoDCHOfSRB34Qua -20 -20
WRAB EbNoDCHRateGainCSAMR -5 -5
WRAB EbNoDCHRateGainCSData -20 -20
WRAB EbNoDCHRateGainPSData -20 -20
WRAB EbNoDCHRateGainSFDown 15 15
WRAB EbNoDCHRateGainSFUp 7 7
WRAB EbNoDCHRateGainSRB -5 -5
WRAB EbNoDCHRxDiv2 -30 -30
WRAB EbNoDCHRxDiv4 -40 -40
WRAB EbNoDCHTxDiv 0 0
WRAB EbNoEDCHCSAMR 40
WRAB EDCHPSStr128Kbps 60 60
WRAB EDCHPSStrOver248Kbps 50 50
WRAB EbNoDCHOfCSDataNT 80 80
WRAB EbNoDCHOfCSDataNTQua -27 -27
WRAB EbNoDCHOfCSDataT 80 80
WRAB EbNoDCHOfCSDataTQua -27 -27
WRAB EbNoDCHOfCSNBAMR122 80 80
WRAB EbNoDCHOfCSNBAMR59 80 80
WRAB EbNoDCHOfCSNBAMRQua -20 -20
WRAB EbNoDCHOfCSNBAMRb -5 -5
WRAB EbNoDCHOfCSNBAMRc -10 -10
WRAB EbNoDCHOfCSWBAMR1265 80 80
WRAB EbNoDCHOfCSWBAMRQua -20 -20
WRAB EbNoDCHOfCSWBAMRb -5 -5
WRAB L1BLERTEDCHVoice10 -10
WRAB L1BLERTEDCHVoice2 -10
WRAB SIRDPCCHInitialDCH128 45 45
WRAB SIRDPCCHInitialDCHHS128 75 45
WRAB SIRDPCCHInitialDCHMax 60 60
WRAB SIRDPCCHInitialDCHMin -60 -60
WRAB SIRDPCCHInitialDCHOffset 0 -20
WRAB SIRDPCCHInitialDCHRxDiv2 -30 -30
WRAB SIRDPCCHInitialDCHRxDiv4 -40 -40
WBTS AdminWBTSState 2 0
WBTS BTSFallbackEnabled 0 0
WBTS BTSSupportForHSPACM 0 0
WBTS BlindHOIntraBTSQCheck 0 0
WBTS BlindTFdetectionUsage 0 0
WBTS BroadcastSIB15 0 0
WBTS BroadcastSIB15_2 0 0
WBTS BroadcastSIB15_3 0 0
WBTS DCHnumberRL 8 0
WBTS DCNLinkStatus 0 1
WBTS DCNSecurityStatus 255 0
WBTS DLORLAveragingWindowSize 0 0
WBTS DSCPHigh 46 46
WBTS DSCPLow 0 0
WBTS DSCPMedDCH 34 34
WBTS DSCPMedHSPA 26 26
WBTS DediMeasRepPeriodCSdata 3 3
WBTS DediMeasRepPeriodPSdata 1 1
WBTS DedicatedMeasReportPeriod 5 5
WBTS DelayThresholdMax 10000 10000
WBTS DelayThresholdMax2msTTI 10000 10000
WBTS DelayThresholdMid 7000 7000
WBTS DelayThresholdMid2msTTI 7000 7000
WBTS DelayThresholdMin 5000 5000
WBTS DelayThresholdMin2msTTI 5000 5000
WBTS HARQRVConfiguration 1 1
WBTS HSDPA14MbpsPerUser 0 1
WBTS HSDPACCEnabled 0 1
WBTS HSDPAIurWeight 0 0
WBTS HSDPAULCToDSCP 34 34
WBTS HSDPAUserHysterisis 0 0
WBTS HSDPAUserThreshold 1 0
WBTS HSUPADLCToDSCP 34 34
WBTS HSUPAXUsersEnabled 0 60
WBTS ICREnabled 0 0
WBTS IPBasedRouteIdIub 0 0
WBTS IPBasedRouteIdIub2 0 0
WBTS IPNBId 0 0
WBTS InactCACThresholdATM 170 170
WBTS InactCACThresholdIP 80 80
WBTS InactUsersCIDThreshold 6 6
WBTS IntelligentSDPrioHO 0 0
WBTS IubTransportFallback 15 0
WBTS IubTransportMedia 0 1
WBTS LoadControlPeriodPS 20 20
WBTS MDCBufferingTime 50 0
WBTS MaxDCHuserRateRLDL 3 0
WBTS MaxDCHuserRateRLUL 3 0
WBTS MaxNumberEDCHLCG 0 160
WBTS MeasFiltCoeff 5 5
WBTS MinUDPPortIub 1026 1026
WBTS NbrOfOverbookedHSDPAUsers 48 48
WBTS NodeBRABReconfigSupport 0 0
WBTS OverbookingSwitch 0 1
WBTS PDUSize656WithHSDSCH 2 2
WBTS PSAveragingWindowSize 4 4
WBTS PSRLAveragingWindowSize 0 0
WBTS PWSMInUse 0 0
WBTS PWSMRemCellSDBeginHour 22 22
WBTS PWSMRemCellSDBeginMin 0 0
WBTS PWSMRemCellSDEndHour 6 6
WBTS PWSMRemCellSDEndMin 0 0
WBTS PWSMShutdownBeginHour 22 22
WBTS PWSMShutdownBeginMin 0 0
WBTS PWSMShutdownEndHour 6 6
WBTS PWSMShutdownEndMin 0 0
WBTS PWSMWeekday 0 0
WBTS ProbabilityFactorMax 1000 1000
WBTS ProbabilityFactorMax2msTTI 1000 1000
WBTS PrxAlpha 0 0
WBTS PrxMeasAveWindow 10 20
WBTS PrxTargetPSAdjustPeriod 5 5
WBTS PtxAlpha 0 0
WBTS PtxDPCHmax -30 -30
WBTS PtxDPCHmin -28 -28
WBTS PtxMeasAveWindow 10 10
WBTS RACHloadIndicationPeriod 1 1
WBTS RFSharingState 0 0
WBTS RRIndPeriod 40 40
WBTS RRMULDCHActivityFactorCSAMR 50 50
WBTS RRMULDCHActivityFactorCSNTData 95 95
WBTS RRMULDCHActivityFactorCSTData 100 100
WBTS RRMULDCHActivityFactorPSBackgr 95 50
WBTS RRMULDCHActivityFactorPSStream 95 50
WBTS RRMULDCHActivityFactorPSTHP1 95 50
WBTS RRMULDCHActivityFactorSRB 1 1
WBTS ReleaseTimerForSharedHSDPAallocation 3 1
WBTS SatelliteIubUsage 0 0
WBTS SchedulingPeriod 100 100
WBTS SharedHSDPAVCCSelectionMethod 0 0
WBTS SharedHSDPAallocation 0 40
WBTS TQMId 0 1
WBTS ToAWEOffsetNRTDCHIP 0 5
WBTS ToAWEOffsetRTDCHIP 0 0
WBTS ToAWSOffsetNRTDCHIP 0 10
WBTS ToAWSOffsetRTDCHIP 0 0
WBTS WinACRABsetupDL 5 5
WBTS WinACRABsetupUL 5 5
WBTS WinLCHSDPA 5 5
WBTS WinLCHSUPA 5 5
WBTS DLCECapacity 0 0
WBTS HSDPACodeCapacity 5 5
WBTS ULCECapacity 0 0
WBTS autoConfMode 1 1
WBTS autoConfPlanReady 0 0
WBTS autoConfStatus 0 0
WBTS bburruFlag 0 0
WBTS nbrRepeater 0 0
WBTS numFa 1 1
WBTS type 3 3
Deviation Remarks ModificatioRNC
1 Cell DL Po
wcel MaxDLPower
wcel PtxCellMax
wcel PtxMaxHSD
wcel PtxTarget
wcel PtxOffset
wcel PtxTargetP
wcel PtxTargetP
wcel PtxHighHS
wcel PtxPrimary
wcel PtxTargetH
0 ok
1
0 Related to HS Cell FACH feature which is not active.

Related to HS Cell FACH feature which is not active.
1
0
1
0 ok
ok
1
0 RNC 127 usYes 127
1
0 ok
ok
1
0 ok
ok
ok
ok
ok
ok
ok
1
0 ok
0
1
0 RNC 127 usYes 127

1
0 ok
1
0
1
0 ok
1
0 ok
ok
1
0 ok
ok
1
0 ok
1
0 ok
Based on license in RNC
Based on license in RNC
0 ok
ok
1
0 ok
1
0 ok
ok
1
0 ok
1
0 ok
1
0 ok
ok
ok
ok
ok
1
0 ok
1
0 ok
1
0 ok
1
0
1
0 RNC 127 usYes 127
1
0 RNC 127 usYes 127
1
0 ok
1
0 ok
ok
1
0 ok
1
0 ok
ok
1
0 ok
ok
1
0 ok
1
0 ok
1
0 RNC 127 usYes 127

1
0 RNC 127 usYes 127
1
0
1
0 ok
1
0 ok
1
0 ok
1
0 ok
1
0 ok
ok
1
0
1
0 ok
1
0 ok
1
0 ok
1
0 ok
RNC 127 usYes 127
1
0 ok
Load and Service Based HO active in 6 RNCs. RNC 111 has Service Based HO only. RNC 11
1
0 ok
1
0 ok
1
0 ok
ok
ok
ok
ok
ok
ok
1
0 ok
ok
ok
ok
ok
ok
1
0 ok
ok
ok
ok
ok
1
0 ok
ok
ok
ok
ok
ok
ok
1
0 ok
1
0 ok
1
0 ok
ok
1
0 ok
1
0 ok
1
0 ok
ok
1
0 ok
ok
ok
1
0 ok
ok
ok
1
0 ok
ok
ok
ok
1
0 RNC127 usiYes 127

RNC127 usiYes 127
1
0 ok
1
0 ok
ok
1
0 ok
1
0 ok
ok
1
0
1
0 RNC 127 usYes 127

1
0 RNC 127 usYes 127

RNC 127 usYes 127
1
0 RNC 127 usYes 127

1
0 RNC 127 usYes 127
1
0 RNC 127 usYes 127

RNC 127 usYes 127
1
0 RNC 127 usYes 127
RNC 127 usYes 127
1
0 RNC 127 usYes 127

1
0 RNC 127 usYes 127

1
0 RNC 127 usYes 127

RNC 127 usYes 127
1
0 RNC 127 usYes 127
RNC 127 usYes 127
1
0 RNC 127 usYes 127

1
0 RNC 127 usYes 127
1
0 Related to Transport Bearer Tuning and this feature is inactive. RNC 126 and RNC 127 is u
Related to Transport Bearer Tuning and this feature is inactive. RNC 126 and RNC 127 is u
1
20W 30W 40W 60W
430 448 460 478
430 448 460 478 CLASS Parameters
430 448 460 478 WCEL AdminCellS
425 443 455 473 WCEL CSGroupId
5 5 5 5 WCEL CTCHCapaH
420 438 450 468 WCEL CUCEcNoTh
360 378 390 408 WCEL CUCRSCPTh
425 443 455 473 WCEL EVAMCapabi
330 354 354 354 WCEL MultiplePL
420 438 450 468 WCEL PCH24kbps
WCEL PRACHDela
WCEL PSGroupId
WCEL PWSMAVLim
WCEL PWSMAVLim
WCEL PWSMAVLim
WCEL PWSMAVLim
WCEL PWSMAVPw
WCEL PWSMAVPw
WCEL PWSMCellG
WCEL PWSMEXPwr
WCEL PWSMEXUsr
WCEL PWSMSDLim
WCEL PWSMSDLim
WCEL PWSMSDLim
WCEL PWSMSDLim
WCEL PWSMSDLim
WCEL PWSMSDPw
WCEL PWSMSDPw
WCEL PWSMSDPw
WCEL PWSMShutd
WCEL PWSMShutd
WCEL PowerSave
WCEL PtxPrimary
WCEL RACHCapac
WCEL RNARGroup
WCEL RRCconnRe
WCEL RRCconnRe
WCEL RelocComm
WCEL SACB
WCEL ShutdownS
WCEL ShutdownW
WCEL ToAWE_CC
WCEL ToAWS_CC
WCEL UTRAN_DRX
WCEL WCELCSCNI
WCEL WCELPSCNI
WCEL WCelState
WCEL NumofEagc
WCEL NumofErgH
WCEL cellLevel
WCEL_AC AMROverS
WCEL_AC AMROverTra
WCEL_AC AMROverT
WCEL_AC AMROverTx
WCEL_AC AMROverTxT
WCEL_AC AMRSF
WCEL_AC AMRTarget
WCEL_AC AMRTargetT
WCEL_AC AMRTarget
WCEL_AC AMRTarget
WCEL_AC AMRTargetT
WCEL_AC AMRUnder
WCEL_AC AMRUnderTr
WCEL_AC AMRUnder
WCEL_AC AMRUnderT
WCEL_AC AMRUnderT
WCEL_AC AdminPICSt
WCEL_AC AssignedPI
WCEL_AC CCHSetupE
WCEL_AC CIRForFDP
WCEL_AC CPICHEcNo
WCEL_AC CPICHRSCP
WCEL_AC CPICHtoRef
WCEL_AC CSAMRMod
WCEL_AC CSAMRMod
WCEL_AC CableLoss
WCEL_AC CodeTreeOp
WCEL_AC CodeTreeOp
WCEL_AC CodeTreeU
WCEL_AC DPCHOverH
WCEL_AC DRRCprxMa
WCEL_AC DRRCprxOff
WCEL_AC DRRCptxMa
WCEL_AC DRRCptxOff
WCEL_AC EVAMInUse
WCEL_AC EvamDInit
WCEL_AC EvamNumPh
WCEL_AC EvamTKeep
WCEL_AC EvamTSwe
WCEL_AC FDPCHCode
WCEL_AC FDPCHEnab
WCEL_AC FDPCHSetu
WCEL_AC HSDPA64QA
WCEL_AC HSDPA64Us
WCEL_AC HSDPAenab
WCEL_AC HSFACHEna
WCEL_AC HSFACHRel
WCEL_AC HSPA72User
WCEL_AC HSPDSCHCo
WCEL_AC HSPDSCHMa
WCEL_AC HSUPA16QA
WCEL_AC HSUPA2MST
WCEL_AC HSUPAUser
WCEL_AC MHA
WCEL_AC MaxBitRat
WCEL_AC MaxBitRat
WCEL_AC MaxCodeRe
WCEL_AC MaxNbrOfH
WCEL_AC PICState
WCEL_AC PrxLoadMa
WCEL_AC PrxLoadMa
WCEL_AC PrxOffsetW
WCEL_AC PtxCellMax
WCEL_AC PtxDLabsM
WCEL_AC PtxFDPCHM
WCEL_AC PtxFDPCHM
WCEL_AC PtxMaxHSD
WCEL_AC PtxOffset
WCEL_AC PtxOffset
WCEL_AC PtxOffset
WCEL_AC PtxOffsetH
WCEL_AC PtxOffsetW
WCEL_AC PtxPSstre
WCEL_AC PtxTargetH
WCEL_AC PtxTargetT
WCEL_AC PtxTargetTo
WCEL_AC RefServFor
WCEL_AC RxDivIndica
WCEL_AC SIRDPCCHO
WCEL_AC SRBBitRat
WCEL_AC SRBMapRRC
WCEL_AC TPCComman
WCEL_AC UEtxPower
WCEL_AC UEtxPower
WCEL_AC UEtxPower
WCEL_AC UsersPerH
WCEL_HC BlindHOEcN
WCEL_HC BlindHORSC
WCEL_HC CellWeight
WCEL_HC DCellHSDP
WCEL_HC DLLoadStat
WCEL_HC HSDPAFmcgIdentifier
WCEL_HC HSDPAFmciIdentifier
WCEL_HC HSDPAFmcsIdentifier
WCEL_HC HSPAFmcsIdentifier
WCEL_HC DirectedRR
WCEL_HC DirectedRR
WCEL_HC HHoMaxAllo
WCEL_HC HHoMaxAllo
WCEL_HC HSCapabil
WCEL_HC HSCapabili
WCEL_HC HSDPALaye
WCEL_HC HSLoadSta
WCEL_HC HSLoadStat
WCEL_HC HSLoadSta
WCEL_HC HSLoadStat
WCEL_HC HSLoadSta
WCEL_HC HSPACapa
WCEL_HC IncomingLT
WCEL_HC LHOCapaRe
WCEL_HC LHOCapaRe
WCEL_HC LHODelayO
WCEL_HC LHODelayO
WCEL_HC LHODelayOF
WCEL_HC LHODelayO
WCEL_HC LHOHardBl
WCEL_HC LHOHardBlo
WCEL_HC LHOHystTi
WCEL_HC LHOHystTim
WCEL_HC LHOHystTim
WCEL_HC LHOHystTi
WCEL_HC LHONRTTraf
WCEL_HC LHONumbUE
WCEL_HC LHONumbUE
WCEL_HC LHOPwrOff
WCEL_HC LHOPwrOff
WCEL_HC LHOResRat
WCEL_HC LHOWinSiz
WCEL_HC LHOWinSize
WCEL_HC LHOWinSize
WCEL_HC LHOWinSiz
WCEL_HC LHOWinSiz
WCEL_HC LHOWinSiz
WCEL_HC LHOWinSize
WCEL_HC LHOWinSiz
WCEL_HC LoadBased
WCEL_HC LoadBased
WCEL_HC MBLBInacti
WCEL_HC MBLBMobili
WCEL_HC MBLBRABSe
WCEL_HC MBLBRABSe
WCEL_HC MBLBStateT
WCEL_HC MIMOHSDP
WCEL_HC MaxNumbe
WCEL_HC NrtFmcgIdentifier
WCEL_HC NrtFmciIdentifier
WCEL_HC NrtFmcsIdentifier
WCEL_HC PFLIdentifier
WCEL_HC RTWithHSDPAFmcgIdentifi
WCEL_HC RTWithHSDPAFmciIdentifie
WCEL_HC RTWithHSDPAFmcsIdentifi
WCEL_HC RTWithHSPAFmcsIdentifie
WCEL_HC RtFmcgIdentifier
WCEL_HC RtFmciIdentifier
WCEL_HC RtFmcsIdentifier
WCEL_HC ServHONum
WCEL_HC ServHONum
WCEL_HC ServHOPeri
WCEL_HC ServHOPeri
WCEL_LC MaxIncrInt
WCEL_LC NonHSEve
WCEL_LC PrxMeasFilt
WCEL_LC PrxNoise
WCEL_LC PrxNoiseAu
WCEL_LC PrxOffset
WCEL_LC PrxTarget
WCEL_LC PrxTargetM
WCEL_LC PrxTotalRep
WCEL_LC PtxMeasFilt
WCEL_LC PtxOffset
WCEL_LC PtxTarget
WCEL_LC PtxTotalRep
WCEL_LC RACHloadRe
WCEL_LC RACHmeasFi
WCEL_LC RSEPSEve
WCEL_LC RTWPEvent
WCEL_LC RTWPEven
WCEL_LC RTWPMeasFi
WCEL_LC TCPEventE
WCEL_LC TCPEvent
WCEL_LC TCPMeasFil
WCEL_LC VoiceOverr
WCEL_PC DPCModeCh
WCEL_PC PRACHRequi
WCEL_PC PTxPICH
WCEL_PC PowerOffs
WCEL_PC PO1_15
WCEL_PC PO1_30
WCEL_PC PO1_60
WCEL_PC PowerRamp
WCEL_PC PtxAICH
WCEL_PC PtxBCCHH
WCEL_PC PtxBCCHH
WCEL_PC PtxMaxEHI
WCEL_PC PtxOffsetE
WCEL_PC PtxOffset
WCEL_PC PtxOffset
WCEL_PC PtxOffsetE
WCEL_PC PtxOffset
WCEL_PC PtxOffsetH
WCEL_PC PtxPrimar
WCEL_PC PtxPrimary
WCEL_PC PtxSCCPCH
WCEL_PC PtxSCCPCH
WCEL_PC PtxSCCPCH
WCEL_PC PtxSCCPCH
WCEL_PC PtxSecSCH
WCEL_PC RsrvdSigna
WCEL_PS AltScrambl
WCEL_PS CPCEnable
WCEL_PS DCellAndM
WCEL_PS DCellHSDP
WCEL_PS DeltaPrxM
WCEL_PS DeltaPrxM
WCEL_PS DeltaPtxM
WCEL_PS DeltaPtxM
WCEL_PS EDCHMinSe
WCEL_PS EDCHMinim
WCEL_PS FachLoadM
WCEL_PS FachLoadT
WCEL_PS HSDPAMPO
WCEL_PS HSDPAMaxB
WCEL_PS HSFACHActT
WCEL_PS HSFACHActi
WCEL_PS HSFACHActi
WCEL_PS HSFACHRLCT
WCEL_PS HSFACHVol
WCEL_PS HSPAQoSEn
WCEL_PS HSUPAEnab
WCEL_PS HspaMultiN
WCEL_PS InitialBitR
WCEL_PS InitialBitR
WCEL_PS MIMOEnabl
WCEL_PS MIMOWith6
WCEL_PS MaxNumbHS
WCEL_PS MaxNumbH
WCEL_PS MaxNumber
WCEL_PS MaxNumber
WCEL_PS MaxNumbe
WCEL_PS MaxNumbe
WCEL_PS MaxNumbe
WCEL_PS MaxNumbe
WCEL_PS MaxTotalUp
WCEL_PS MinAllowed
WCEL_PS MinAllowed
WCEL_PS NASsignVol
WCEL_PS NASsignVol
WCEL_PS NumberEDC
WCEL_PS OCULNRTDC
WCEL_PS OCdlNrtDCH
WCEL_PS PBSgranted
WCEL_PS PBSgranted
WCEL_PS PBSgranted
WCEL_PS PrxLoadMa
WCEL_PS PrxMaxOrig
WCEL_PS PrxMaxTarg
WCEL_PS PrxTargetP
WCEL_PS PrxTargetP
WCEL_PS PrxTargetP
WCEL_PS PrxTargetP
WCEL_PS PtxHighHS
WCEL_PS PtxMargin
WCEL_PS PtxTargetP
WCEL_PS PtxTargetP
WCEL_PS PtxTargetP
WCEL_PS PtxTargetP
WCEL_PS PtxTargetP
WCEL_PS PtxThresho
WCEL_PS RachLoadM
WCEL_PS RachLoadT
WCEL_PS TargetNSE
WCEL_PS TrafVolThr
WCEL_PS ULLoadSta
WCEL_PS ULLoadStat
WCEL_SIB ACBarredLi
WCEL_SIB AICHTraTim
WCEL_SIB AbsPrioCell
WCEL_SIB AllowedPre
WCEL_SIB AllowedRA
WCEL_SIB CellBarred
WCEL_SIB CellSelQua
WCEL_SIB Cell_Reser
WCEL_SIB HCS_PRIO
WCEL_SIB InterFreqSc
WCEL_SIB InterRATSca
WCEL_SIB IntraFreq_C
WCEL_SIB KforCTCH
WCEL_SIB LTECellRese
WCEL_SIB N300
WCEL_SIB N312
WCEL_SIB N312Conn
WCEL_SIB N313
WCEL_SIB N315
WCEL_SIB NCr
WCEL_SIB NbrOfSCCP
WCEL_SIB NforCTCH
WCEL_SIB NonHCSNcr
WCEL_SIB NonHCSTcr
WCEL_SIB NonHCSTcr
WCEL_SIB PI_amount
WCEL_SIB PRACHScra
WCEL_SIB PRACH_prea
WCEL_SIB QHCS
WCEL_SIB Qhyst1
WCEL_SIB Qhyst1FAC
WCEL_SIB Qhyst1PCH
WCEL_SIB Qhyst2
WCEL_SIB Qhyst2FAC
WCEL_SIB Qhyst2PCH
WCEL_SIB QqualMin
WCEL_SIB QrxlevMin
WCEL_SIB RACHInter
WCEL_SIB RACHIntraF
WCEL_SIB RACH_Tx_N
WCEL_SIB RACH_Tx_N
WCEL_SIB RACH_tx_M
WCEL_SIB SHCS_RAT
WCEL_SIB SHCS_RATC
WCEL_SIB SIB4Indicat
WCEL_SIB SIB7factor
WCEL_SIB Sintersearc
WCEL_SIB Sintersear
WCEL_SIB Sintrasearc
WCEL_SIB Sintrasear
WCEL_SIB Slimit_Sea
WCEL_SIB Slimit_Sea
WCEL_SIB SpeedScale
WCEL_SIB Spriorityse
WCEL_SIB Spriorityse
WCEL_SIB SsearchHC
WCEL_SIB SsearchHC
WCEL_SIB Ssearch_RA
WCEL_SIB Ssearch_R
WCEL_SIB T300
WCEL_SIB T312
WCEL_SIB T312Conn
WCEL_SIB T313
WCEL_SIB T315
WCEL_SIB TBarred
WCEL_SIB TCrmax
WCEL_SIB TCrmaxHys
WCEL_SIB Threshserv
WCEL_SIB Treselectio
WCEL_SIB Treselecti
WCEL_SIB Treselecti
WCEL_SIB UseOfHCS
Based HO only. RNC 119, RNC 121 and RNC 126 having Load Based HO.
C 126 and RNC 127 is using default.
TEMPLATE
1 rf 900 1rf 2100 2rf+2hs 2100

default Celcom Deviation Remarks Modificatiocarrier 1 carrier 1 carrier 1
0 1 0 Cell lock/unlock status.
0 0 1 0 0 0
0 0 0 0 0
31 31 31 31 31
-92 -92 -92 -92 -92
1 0 0 no value 0 0 0
0 0 1 0 0 0
0 1 0 24 kbps paging channe 1 1 1
3 3 1 3 3 3
0 0 0 0 0
10 10 10 10 10
10 10 10 10 10
37 37 37 37 37
0 0 0 0 0
31 31 31 31 31
37 37 37 37 37
0 0 0 0 0
37 37 37 37 37
5 5 5 5 5
5 5 5 5 5
10 10 10 10 10
5 5 5 5 5
10 10 10 10 10
5 5 5 5 5
34 34 34 34 34
37 37 37 37 37
34 34 34 34 34
0 0 0 0 0
0 0 0 0 0
0 0 0 0 0
330 354 0 cell specif Yes Refer to worksheet " summary configuration"
2 2 1 2 2 2
0 0 0 0 0
6 6 6 6 6
5 5 5 5 5
0 0 0 0 0
0 0 0 0 0
10 10 10 10 10
15 15 15 15 15
10 10 10 10 10
25 25 25 25 25
5 5 5 5 5
65535 1 0 ok 1 1 1
65535 2 ok 2 2 2
0 0 1 0 0 0
1 1 1 1 1
1 1 1 1 1
0 0 0 0 0
90 90 90 90 90
9 9 9 9 9
-10 -10 -10 -10 -10
0 0 0 0 0
20 20 20 20 20
-2 -2 -2 -2 -2
70 70 70 70 70
8 8 8 8 8
-20 -20 -20 -20 -20
-10 -10 -10 -10 -10
0 0 0 0 0
50 50 50 50 50
2 2 2 2 2
-100 -100 -100 -100 -100
-100 -100 -100 -100 -100
-100 -100 -100 -100 -100
1 1 1 1 1
0 0 0 0 0
0 1 0 Common channel setup 1 1 1
-44 -44 1 -44 -44 -44
-16 -16 -16 -16 -16
-92 -92 -92 -92 -92
20 -40 0 Celcom defa
Yes -40 -40 -40
0 7 ok 7 7 7
0 1 ok 1 1 1
30 30 1 30 30 30
3600 3600 3600 3600 3600
1 1 1 1 1
40 40 40 40 40
5 5 5 5 5
0 0 0 0 0
-10 -10 -10 -10 -10
-5 -5 -5 -5 -5
-30 -30 -30 -30 -30
0 0 0 0 0
0 0 0 0 0
8 0 0 no value 0 0 0
4320 0 no value 0 0 0
216 0 no value 0 0 0
6 6 1 6 6 6
0 0 0 0 0
0 0 0 0 0
0 1 0 HSDPA 64 QAM feature 1 1 1
0 1 HSDPA 64 users featur 1 1 1
0 1 enabled 1 1 1
0 0 1 0 0 0
458124 0 0 no value. Related to H 0 0 0
0 1 HSPA 72 users license 1 1 1
32 54560 ok 54560 54560 54560
8 8 1 8 8 8
0 0 0 0 0
0 1 0 HSUPA 2ms TTI featur 1 1 1
2 0 no value. Related to 0 0 0
0 0 1 0 0 0
384 384 384 384 384
384 384 384 384 384
40 40 40 40 40
1 4 0 4 HS SCCHYes 4 4 4
1 1 1 1 1 1
20 40 0 ok 40 40 40
0 0 1 0 0 0
8 0 0 no value 0 0 0
430 460 depends onYes Refer to worksheet " summary configuration"
370 370 1 370 370 370
90 90 90 90 90
200 200 200 200 200
430 460 0 depends onYes Refer to worksheet " summary configuration"
20 20 1 20 20 20
12 12 12 12 12
6 6 6 6 6
8 10 0 ok 10 10 10
8 0 no value 0 0 0
370 370 1 370 370 370
385 450 0 depends on power sett Refer to worksheet " summary configuration"
32767 32767 1 32767 32767 32767
32767 32767 32767 32767 32767
0 0 0 0 0
1 1 1 1 1
0 0 0 0 0
66559 508927 0 ok 508927 508927 508927
457728 310272 ok 310272 310272 310272
4 4 1 4 4 4
24 24 24 24 24
21 21 21 21 21
21 21 21 21 21
30 0 0 no value 0 0 0
-24 0 ok, RACH EYes 0 0 0
-95 -25 ok Yes -25 -25 -25
100 100 1 100 100 100
0 0 0 0 0
4 4 4 4 4
SDPAFmcgIdentifier
SDPAFmciIdentifier
SDPAFmcsIdentifier
SPAFmcsIdentifier
1 0 0 not enabled as MBLB i 0 0 0
0 1 Enabled for HSDPA 1 1 1
32 64 ok Yes 64 64 64
32 64 ok Yes 64 64 64
3 3 1 3 3 3
5 0 0 ok Yes 0 0 0
0 1 enabled. Yes 1 1 1
32 32 1 32 32 32
127 127 127 127 127
24 24 24 24 24
127 127 127 127 127
2 2 2 2 2
0 0 0 0 0
0 1 0 ok, based oYes 1 1 1
70 70 1 70 70 70
70 70 70 70 70
30 30 30 30 30
30 30 30 30 30
30 30 30 30 30
30 30 30 30 30
10 10 10 10 10
50 50 50 50 50
2 2 2 2 2
2 2 2 2 2
2 2 2 2 2
2 2 2 2 2
10 10 10 10 10
0 0 0 0 0
0 0 0 0 0
-15 -15 -15 -15 -15
-7 -7 -7 -7 -7
80 80 80 80 80
5 5 5 5 5
5 5 5 5 5
5 5 5 5 5
5 5 5 5 5
0 0 0 0 0
0 0 0 0 0
0 0 0 0 0
0 0 0 0 0
-25 -25 -25 -25 -25
0 0 0 0 0
0 0 0 0 0
0 0 0 0 0
0 1 0 MBLB enablYes 0 0 0
1 1 1 1 1 1
0 1 0 MBLB enablYes 0 0 0
0 0 1 0 0 0
6 6 6 6 6
rtFmcgIdentifier
rtFmciIdentifier
rtFmcsIdentifier
FLIdentifier
TWithHSDPAFmcgIdentifier 1
TWithHSDPAFmciIdentifier
TWithHSDPAFmcsIdentifier
TWithHSPAFmcsIdentifier
tFmcgIdentifier
tFmciIdentifier
tFmcsIdentifier
1 2 0 Service and Load Base 2 2 2
1 1 1 1 1 1
0 0 0 0 0
0 0 0 0 0
10 10 10 10 10
1 0 0 no value 0 0 0
2 2 1 2 2 2
-1050 -1050 -1050 -1050 -1050
1 1 1 1 1
10 10 10 10 10
40 80 0 ok Yes 80 80 80
65535 65535 1 65535 65535 65535
80 0 0 no value 0 0 0
2 2 1 2 2 2
10 5 0 ok Yes 5 5 5
400 455 depends on power sett
Refer to worksheet " summary configuration"
80 0 no value 0 0 0
80 0 no value 0 0 0
10 10 1 10 10 10
1 0 0 no value 0 0 0
20 0 no value 0 0 0
1 0 no value 0 0 0
2 0 no value 0 0 0
20 0 no value 0 0 0
1 0 no value 0 0 0
2 0 no value 0 0 0
1 1 1 1 1 1
1 1 1 1 1
-25 -20 0 ok -20 -20 -20
-8 -8 1 -8 -8 -8
2 -3 0 ok -3 -3 -3
8 8 1 8 8 8
12 12 12 12 12
16 16 16 16 16
2 3 0 ok 3 3 3
-8 -3 ok -3 -3 -3
70 0 no value 0 0 0
-20 0 no value 0 0 0
84 84 1 84 84 84
108 108 108 108 108
128 128 128 128 128
128 128 128 128 128
84 84 84 84 84
128 128 128 128 128
140 0 0 no value 0 0 0
-50 -50 1 -50 -50 -50
-30 -30 -30 -30 -30
0 0 0 0 0
-50 0 0 ok 0 0 0
-20 0 ok 0 0 0
-20 -20 1 -20 -20 -20
-30 -30 -30 -30 -30
10 10 10 10 10
0 0 0 0 0
0 0 0 0 0
0 0 0 0 0
0 1 0 enabled feature 1 1 1
4 10 ok 10 10 10
6 6 1 6 6 6
4 4 4 4 4
6 15 0 ok 15 15 15
29 29 1 29 29 29
4 4 4 4 4
5 5 5 5 5
75 75 75 75 75
12 0 0 no value 0 0 0
6 6 1 6 6 6
0 0 0 0 0
1 0 0 no value 0 0 0
16 0 no value 0 0 0
0 0 1 0 0 0
512 0 0 no value 0 0 0
0 2 ok 2 2 2
0 1 enabled 1 1 1
0 1 enabled 1 1 1
64 64 1 64 64 64
64 64 64 64 64
0 0 0 0 0
0 0 0 0 0
0 0 0 0 0
0 0 0 0 0
0 72 0 ok 72 72 72
0 0 1 0 0 0
0 0 0 0 0
16 16 16 16 16
10 10 10 10 10
5 5 5 5 5
0 3 0 ok, for 5.8 Yes 3 3 3
8 64 ok Yes 64 64 64
8 64 ok yes 64 64 64
8 8 1 8 8 8
8 8 8 8 8
2 2 2 2 2
10 10 10 10 10
60 60 60 60 60
20 20 20 20 20
30 30 30 30 30
15 15 15 15 15
20 20 20 20 20
80 80 80 80 80
60 100 0 ok, in shr1 Yes 100 100 100
40 80 ok Yes 80 80 80
40 80 ok Yes 80 80 80
5 5 1 5 5 5
5 5 5 5 5
410 455 0 depends onYes Refer to worksheet " summary configuration"
5 5 1 5 5 5
5 10 0 ok Yes 10 10 10
10 10 1 10 10 10
10 10 10 10 10
-10 -10 -10 -10 -10
5 5 5 5 5
75 75 75 75 75
30 50 0 ok Yes 50 50 50
128 512 ok Yes 512 512 512
8 8 1 8 8 8
-5 127 0 ok Yes 127 127 127
0 0 1 0 0 0
0 0 0 0 0
0 0 0 3 3
15 15 15 15 15
4095 4095 4095 4095 4095
1 1 1 1 1
0 0 0 0 0
1 1 1 1 1
0 0 0 0 0
4 4 4 4 4
4 4 4 4 4
0 0 0 0 0
0 0 0 0 0
0 1 0 ok, based oYes 1 1 1
3 2 ok Yes 2 2 2
2 2 1 2 2 2
2 2 2 2 2
4 4 4 4 4
0 0 0 0 0
8 8 8 8 8
1 2 0 ok Yes 2 2 2
2 2 1 2 2 2
8 8 8 8 8
0 0 0 0 0
0 0 0 0 0
2 2 2 2 2
0 0 0 0 0
8 8 8 8 8
0 0 0 0 0
0 0 0 0 0
0 0 0 0 0
0 0 0 0 0
1 1 1 1 1
2 2 2 2 2
2 2 2 2 2
-18 -18 -18 -18 -18
-58 -58 -58 -58 -58
1 0 0 ok, for MBLYes 1 1 1
0 1 ok, for MBLYes 0 0 0
50 50 1 50 50 50
0 20 0 ok Yes 20 20 20
8 4 ok Yes 4 4 4
-1 -1 1 -1 -1 -1
-1 -1 -1 -1 -1
0 1 0 ok Yes 1 1 1
0 0 1 0 0 0
4 3 0 ok for U2100
Yes 7 3 3
4 3 ok for U2100
Yes 7 3 3
5 5 1 5 5 5
5 5 5 5 5
1 1 1 1 1
1 1 1 1 1
7 7 7 7 7
0 3 0 ok Yes 3 3 3
0 2 ok Yes 2 2 2
-1 -1 1 -1 -1 -1
-1 -1 -1 -1 -1
2 1 0 ok Yes 1 1 1
2 1 ok Yes 1 1 1
10 10 1 10 10 10
6 6 6 6 6
1 6 0 ok Yes 6 6 6
3 2 ok Yes 2 2 2
4 2 ok Yes 2 2 2
2 2 1 2 2 2
2 2 2 2 2
0 0 0 0 0
0 1 0 ok, it is a Yes 1 1 1
2 2 1 2 2 2
10 10 10 10 10
2 2 2 2 2
0 0 0 0 0
2rf+2hs 2100 3rf+3hs 2100 POWER (W)
carrier 2 carrier 1 carrier 2 carrier 3 20 30 40 60
0 0 0 0
0 0 0 0
31 31 31 31
-92 -92 -92 -92
0 0 0 0
0 0 0 0
1 1 1 1
3 3 3 3
0 0 0 0
10 10 10 10
10 10 10 10
37 37 37 37
0 0 0 0
31 31 31 31
37 37 37 37
0 0 0 0
37 37 37 37
5 5 5 5
5 5 5 5
10 10 10 10
5 5 5 5
10 10 10 10
5 5 5 5
34 34 34 34
37 37 37 37
34 34 34 34
0 0 0 0
0 0 0 0
0 0 0 0
ummary configuration" 330 354 354 354
2 2 2 2
0 0 0 0
6 6 6 6
5 5 5 5
0 0 0 0
0 0 0 0
10 10 10 10
15 15 15 15
10 10 10 10
25 25 25 25
5 5 5 5
1 1 1 1
2 2 2 2
0 0 0 0
1 1 1 1
1 1 1 1
0 0 0 0
90 90 90 90
9 9 9 9
-10 -10 -10 -10
0 0 0 0
20 20 20 20
-2 -2 -2 -2
70 70 70 70
8 8 8 8
-20 -20 -20 -20
-10 -10 -10 -10
0 0 0 0
50 50 50 50
2 2 2 2
-100 -100 -100 -100
-100 -100 -100 -100
-100 -100 -100 -100
1 1 1 1
0 0 0 0
1 1 1 1
-44 -44 -44 -44
-16 -16 -16 -16
-92 -92 -92 -92
-40 -40 -40 -40
7 7 7 7
1 1 1 1
30 30 30 30
3600 3600 3600 3600
1 1 1 1
40 40 40 40
5 5 5 5
0 0 0 0
-10 -10 -10 -10
-5 -5 -5 -5
-30 -30 -30 -30
0 0 0 0
0 0 0 0
0 0 0 0
0 0 0 0
0 0 0 0
6 6 6 6
0 0 0 0
0 0 0 0
1 1 1 1
1 1 1 1
1 1 1 1
0 0 0 0
0 0 0 0
1 1 1 1
54560 54560 54560 54560
8 8 8 8
0 0 0 0
1 1 1 1
0 0 0 0
0 0 0 0
384 384 384 384
384 384 384 384
40 40 40 40
4 4 4 4
1 1 1 1
40 40 40 40
0 0 0 0
0 0 0 0
370 370 370 370
90 90 90 90
200 200 200 200
20 20 20 20
12 12 12 12
6 6 6 6
10 10 10 10
0 0 0 0
370 370 370 370
32767 32767 32767 32767
32767 32767 32767 32767
0 0 0 0
1 1 1 1
0 0 0 0
508927 508927 508927 508927
310272 310272 310272 310272
4 4 4 4
24 24 24 24
21 21 21 21
21 21 21 21
0 0 0 0
0 0 0 0
-25 -25 -25 -25
100 100 100 100
0 0 0 0
4 4 4 4
0 0 0 0
1 1 1 1
64 64 64 64
64 64 64 64
3 3 3 3
0 0 0 0
1 1 1 1
32 32 32 32
127 127 127 127
24 24 24 24
127 127 127 127
2 2 2 2
0 0 0 0
1 1 1 1
70 70 70 70
70 70 70 70
30 30 30 30
30 30 30 30
30 30 30 30
30 30 30 30
10 10 10 10
50 50 50 50
2 2 2 2
2 2 2 2
2 2 2 2
2 2 2 2
10 10 10 10
0 0 0 0
0 0 0 0
-15 -15 -15 -15
-7 -7 -7 -7
80 80 80 80
5 5 5 5
5 5 5 5
5 5 5 5
5 5 5 5
0 0 0 0
0 0 0 0
0 0 0 0
0 0 0 0
-25 -25 -25 -25
0 0 0 0
0 0 0 0
0 0 0 0
0 0 0 0
1 1 1 1
0 0 0 0
0 0 0 0
6 6 6 6
2 2 2 2
1 1 1 1
0 0 0 0
0 0 0 0
10 10 10 10
0 0 0 0
2 2 2 2
-1050 -1050 -1050 -1050
1 1 1 1
10 10 10 10
80 80 80 80
65535 65535 65535 65535
0 0 0 0
2 2 2 2
5 5 5 5 5 5 5 5
0 0 0 0
0 0 0 0
10 10 10 10
0 0 0 0
0 0 0 0
0 0 0 0
0 0 0 0
0 0 0 0
0 0 0 0
0 0 0 0
1 1 1 1
1 1 1 1
-20 -20 -20 -20
-8 -8 -8 -8
-3 -3 -3 -3
8 8 8 8
12 12 12 12
16 16 16 16
3 3 3 3
-3 -3 -3 -3
0 0 0 0
0 0 0 0
84 84 84 84
108 108 108 108
128 128 128 128
128 128 128 128
84 84 84 84
128 128 128 128
0 0 0 0
-50 -50 -50 -50
-30 -30 -30 -30
0 0 0 0
0 0 0 0
0 0 0 0
-20 -20 -20 -20
-30 -30 -30 -30
10 10 10 10
0 0 0 0
0 0 0 0
0 0 0 0
1 1 1 1
10 10 10 10
6 6 6 6
4 4 4 4
15 15 15 15
29 29 29 29
4 4 4 4
5 5 5 5
75 75 75 75
0 0 0 0
6 6 6 6
0 0 0 0
0 0 0 0
0 0 0 0
0 0 0 0
0 0 0 0
2 2 2 2
1 1 1 1
1 1 1 1
64 64 64 64
64 64 64 64
0 0 0 0
0 0 0 0
0 0 0 0
0 0 0 0
72 72 72 72
0 0 0 0
0 0 0 0
16 16 16 16
10 10 10 10
5 5 5 5
3 3 3 3
64 64 64 64
64 64 64 64
8 8 8 8
8 8 8 8
2 2 2 2
10 10 10 10
60 60 60 60
20 20 20 20
30 30 30 30
15 15 15 15
20 20 20 20
80 80 80 80
100 100 100 100
80 80 80 80
80 80 80 80
5 5 5 5
5 5 5 5
5 5 5 5
10 10 10 10
10 10 10 10
10 10 10 10
-10 -10 -10 -10
5 5 5 5
75 75 75 75
50 50 50 50
512 512 512 512
8 8 8 8
127 127 127 127
0 0 0 0
0 0 0 0
2 3 2 2
15 15 15 15
4095 4095 4095 4095
1 1 1 1
0 0 0 0
1 1 1 1
0 0 0 0
4 4 4 4
4 4 4 4
0 0 0 0
0 0 0 0
1 1 1 1
2 2 2 2
2 2 2 2
2 2 2 2
4 4 4 4
0 0 0 0
8 8 8 8
2 2 2 2
2 2 2 2
8 8 8 8
0 0 0 0
0 0 0 0
2 2 2 2
0 0 0 0
8 8 8 8
0 0 0 0
0 0 0 0
0 0 0 0
0 0 0 0
1 1 1 1
2 2 2 2
2 2 2 2
-18 -18 -18 -18
-58 -58 -58 -58
1 1 1 1
0 0 0 0
50 50 50 50
20 20 20 20
4 4 4 4
-1 -1 -1 -1
-1 -1 -1 -1
1 1 1 1
0 0 0 0
3 3 3 3
3 3 3 3
5 5 5 5
5 5 5 5
1 1 1 1
1 1 1 1
7 7 7 7
3 3 3 3
2 2 2 2
-1 -1 -1 -1
-1 -1 -1 -1
1 1 1 1
1 1 1 1
10 10 10 10
6 6 6 6
6 6 6 6
2 2 2 2
2 2 2 2
2 2 2 2
2 2 2 2
0 0 0 0
1 1 1 1
2 2 2 2
10 10 10 10
2 2 2 2
0 0 0 0
LTE InterwoMBLB
10762 10712 10737 U9
0 0 0 0 0
0 0 0 0 0
31 31 31 31 31
-92 -92 -92 -92 -92
0 0 0 0 0
0 0 0 0 0
1 1 1 1 1
3 3 3 3 3
0 0 0 0 0
10 10 10 10 10
10 10 10 10 10
37 37 37 37 37
0 0 0 0 0
31 31 31 31 31
37 37 37 37 37
0 0 0 0 0
37 37 37 37 37
5 5 5 5 5
5 5 5 5 5
10 10 10 10 10
5 5 5 5 5
10 10 10 10 10
5 5 5 5 5
34 34 34 34 34
37 37 37 37 37
34 34 34 34 34
0 0 0 0 0
0 0 0 0 0
0 0 0 0 0
2 2 2 2 2
0 0 0 0 0
6 6 6 6 6
5 5 5 5 5
0 0 0 0 0
0 0 0 0 0
10 10 10 10 10
15 15 15 15 15
10 10 10 10 10
25 25 25 25 25
5 5 5 5 5
1 1 1 1 1
2 2 2 2 2
0 0 0 0 0
1 1 1 1 1
1 1 1 1 1
0 0 0 0 0
90 90 90 90 90
9 9 9 9 9
-10 -10 -10 -10 -10
0 0 0 0 0
20 20 20 20 20
-2 -2 -2 -2 -2
70 70 70 70 70
8 8 8 8 8
-20 -20 -20 -20 -20
-10 -10 -10 -10 -10
0 0 0 0 0
50 50 50 50 50
2 2 2 2 2
-100 -100 -100 -100 -100
-100 -100 -100 -100 -100
-100 -100 -100 -100 -100
1 1 1 1 1
0 0 0 0 0
1 1 1 1 1
-44 -44 -44 -44 -44
-16 -16 -16 -16 -16
-92 -92 -92 -92 -92
-40 -40 -40 -40 -40
7 7 7 7 7
1 1 1 1 1
30 30 30 30 30
3600 3600 3600 3600 3600
1 1 1 1 1
40 40 40 40 40
5 5 5 5 5
0 0 0 0 0
-10 -10 -10 -10 -10
-5 -5 -5 -5 -5
-30 -30 -30 -30 -30
0 0 0 0 0
0 0 0 0 0
0 0 0 0 0
0 0 0 0 0
0 0 0 0 0
6 6 6 6 6
0 0 0 0 0
0 0 0 0 0
1 1 1 1 1
1 1 1 1 1
1 1 1 1 1
0 0 0 0 0
0 0 0 0 0
1 1 1 1 1
54560 54560 54560 54560 54560
8 8 8 8 8
0 0 0 0 0
1 1 1 1 1
0 0 0 0 0
0 0 0 0 0
384 384 384 384 384
384 384 384 384 384
40 40 40 40 40
4 4 4 4 4
1 1 1 1 1
40 40 40 40 40
0 0 0 0 0
0 0 0 0 0
370 370 370 370 370

90 90 90 90 90
200 200 200 200 200
20 20 20 20 20
12 12 12 12 12
6 6 6 6 6
10 10 10 10 10
0 0 0 0 0
370 370 370 370 370
32767 32767 32767 32767 32767

32767 32767 32767 32767 32767
0 0 0 0 0
1 1 1 1 1
0 0 0 0 0
508927 508927 508927 508927 508927
310272 310272 310272 310272 310272
4 4 4 4 4
24 24 24 24 24
21 21 21 21 21
21 21 21 21 21
0 0 0 0 0
0 0 0 0 0
-25 -25 -25 -25 -25
100 100 100 100 80
0 33 37 41 45
4 4 4 4 4
33 37 41 45
33 37 41 45
33 37 41 45
33 37 41 45
0 0 0 0 0
1 1 1 1 1
64 64 64 64 64
64 64 64 64 64
3 3 3 3 3
0 0 0 0 0
1 1 1 1 1
32 32 32 32 32
127 127 127 127 127
24 24 24 24 24
127 127 127 127 127
2 2 2 2 2
0 0 0 0 0
1 1 1 1 1
70 70 70 70 70
70 70 70 70 70
30 30 30 30 30
30 30 30 30 30
30 30 30 30 30
30 30 30 30 30
10 10 10 10 10
50 50 50 50 50
2 2 2 2 2
2 2 2 2 2
2 2 2 2 2
2 2 2 2 2
10 10 10 10 10
0 0 0 0 0
0 0 0 0 0
-15 -15 -15 -15 -15
-7 -7 -7 -7 -7
80 80 80 80 80
5 5 5 5 5
5 5 5 5 5
5 5 5 5 5
5 5 5 5 5
0 0 0 0 0
0 0 0 0 0
0 0 0 0 0
0 0 0 0 0
-25 -25 -25 -25 -25
0 0 0 0 0
0 0 0 0 0
0 0 0 0 0
0 1 1 1 1
1 1 1 1 1
0 1 1 1 1
0 0 0 0 0
6 6 6 6 6
32 36 40 44
32 36 40 44
32 36 40 44
47 48 49 50
34 38 42 46
34 38 42 46
34 38 42 46
34 38 42 46
31 35 39 43
31 35 39 43
31 35 39 43
2 2 2 2 2
1 1 1 1 1
0 0 0 0 0
0 0 0 0 0
10 10 10 10 10
0 0 0 0 0
2 2 2 2 2
-1050 -1050 -1050 -1050 -1050
1 1 1 1 1
10 10 10 10 10
80 80 80 80 80
65535 65535 65535 65535 65535
0 0 0 0 0
2 2 2 2 2
5 5 5 5 5
0 0 0 0 0
0 0 0 0 0
10 10 10 10 10
0 0 0 0 0
0 0 0 0 0
0 0 0 0 0
0 0 0 0 0
0 0 0 0 0
0 0 0 0 0
0 0 0 0 0
1 1 1 1 1
1 1 1 1 1
-20 -20 -20 -20 -20
-8 -8 -8 -8 -8
-3 -3 -3 -3 -3
8 8 8 8 8
12 12 12 12 12
16 16 16 16 16
3 3 3 3 3
-3 -3 -3 -3 -3
0 0 0 0 0
0 0 0 0 0
84 84 84 84 84
108 108 108 108 108
128 128 128 128 128
128 128 128 128 128
84 84 84 84 84
128 128 128 128 128
0 0 0 0 0
-50 -50 -50 -50 -50
-30 -30 -30 -30 -30
0 0 0 0 0
0 0 0 0 0
0 0 0 0 0
-20 -20 -20 -20 -20
-30 -30 -30 -30 -30
10 10 10 10 10
0 0 0 0 0
0 0 0 0 0
0 0 0 0 0
1 1 1 1 1
10 10 10 10 10
6 6 6 6 6
4 4 4 4 4
15 15 15 15 15
29 29 29 29 29
4 4 4 4 4
5 5 5 5 5
75 75 75 75 75
0 0 0 0 0
6 6 6 6 6
0 0 0 0 0
0 0 0 0 0
0 0 0 0 0
0 0 0 0 0
0 0 0 0 0
2 2 2 2 2
1 1 1 1 1
1 1 1 1 1
64 64 64 64 64
64 64 64 64 64
0 0 0 0 0
0 0 0 0 0
0 0 0 0 0
0 0 0 0 0
72 72 72 72 72
0 0 0 0 0
0 0 0 0 0
16 16 16 16 16
10 10 10 10 10
5 5 5 5 5
3 3 3 3 3
64 64 64 64 64
64 64 64 64 64
8 8 8 8 8
8 8 8 8 8
2 2 2 2 2
10 10 10 10 10
60 60 60 60 60
20 20 20 20 20
30 30 30 30 30
15 15 15 15 15
20 20 20 20 20
80 80 80 80 80
100 100 100 100 100
80 80 80 80 80
80 80 80 80 80
5 5 5 5 5
5 5 5 5 5
5 5 5 5 5
10 10 10 10 10
10 10 10 10 10
10 10 10 10 10
-10 -10 -10 -10 -10
5 5 5 5 5
75 75 75 75 75
50 50 50 50 50
512 512 512 512 512
8 8 8 8 8
127 127 127 127 127
0 0 0 0 0
0 0 0 0 0
3 3 2 2 0
15 15 15 15 15
4095 4095 4095 4095 4095
1 1 1 1 1
0 0 0 0 0
1 1 1 1 1
0 0 0 0 0
4 4 4 4 4
4 4 4 4 4
0 0 0 0 0
0 0 0 0 0
1 1 1 1
2 2 2 2 2
2 2 2 2 2
2 2 2 2 2
4 4 4 4 4
0 0 0 0 0
8 8 8 8 8
2 2 2 2 2
2 2 2 2 2
8 8 8 8 8
0 0 0 0 0
0 0 0 0 0
2 2 2 2 2
0 0 0 0 0
8 8 8 8 8
0 0 0 0 0
0 0 0 0 0
0 0 0 0 0
0 0 0 0 0
1 1 1 1 1
2 2 2 2 2
2 2 2 2 2
-18 -18 -18 -18 -18
-58 -58 -58 -58 -58
1 0 0 0 0
0 1 1 1 1
50 50 50 50 50
20 20 20 20 20
4 4 4 4 4
-1 -1 -1 -1 -1
-1 -1 -1 -1 -1
1 1 1 1 1
0 0 0 0 0
3 3 3 3 7
3 3 3 3 7
5 5 5 5 5
5 5 5 5 5
1 1 1 1 1
1 1 1 1 1
7 7 7 7 7
3 3 3 3 3
2 2 2 2 2
-1 -1 -1 -1 -1
-1 -1 -1 -1 -1
1 1 1 1 1
1 1 1 1 1
10 10 10 10 10
6 6 6 6 6
6 6 6 6 6
2 2 2 2 2
2 2 2 2 2
2 2 2 2 2
2 2 2 2 2
0 0 0 0 0
1 1 1 1 1
2 2 2 2 2
10 10 10 10 10
2 2 2 2 2
0 0 0 0 0

3G KPI Optimization Sheet Nokia

Uploaded by

Copyright:

Available Formats

3G KPI Optimization Sheet Nokia

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

3G KPI Optimization Sheet Nokia

Uploaded by

Copyright:

Available Formats

What are some of the main metrics and KPIs discussed for analyzing network performance?

What are some of the main metrics and KPIs discussed for analyzing network performance?

What are some of the steps described for prioritizing analysis of underperforming cells?

What are some of the steps described for prioritizing analysis of underperforming cells?

Jump/Network Operations Portal NOP (intranet)

–Includes counters, KPIs and also reports in Reporting Suite

In Loaded networks the Weekly Busy Hour CSSR is relevant

mparison between large areas (Cities, RNCs) is still required

Call Setup Success Rate (CSSR)

1) Site Ok?-- Cell Availability(Cell level report-RSRAN001), Alarms/HW Issues

2) Coverage or Interference-- Cell Power Report

3) AICH ACK. Received?----No (UL Coverage & RACH parameter Optimization)

RRC_CONN_STP_FAIL_BTS (dominant when HSDPA active)

•Frozen BTS/BTS not responding-- delete and re-create COCO/Site Reset

DCH Reconfiguration failures due to AC/BTS/Trans-- NRT_DCH_Allocations_Statistics report

RRC_CONN_STP_FAIL_RNTI ALLO FAIL

Some more counters of RRC Access fails

RAB Access fails occurs (due to UE & RNC fails)-----

RAB setup & Access Fail Root Cause Analysis

RAB_CONN_STP_FAIL_BTS (dominant when HSDPA active)

•Frozen BTS/BTS not responding-- delete and re-create COCO/Site Reset

DCH Reconfiguration failures due to AC/BTS/Trans-- NRT_DCH_Allocations_Statistics report

RAB_CONN_STP_FAIL_RNTI ALLO FAIL

RAB_ACC_FAIL_Iur trans--- RNC capacity Report

RRC_CONN_ACC_FAIL_RADIO (Dominant failure cause type)

Packet Service & Session [ PS ]

Packet Session RAB Setup Failures

Packet Session Setup Failures (R99)

•TRANS failure: lack of Iub capacity (COCO parameters)

Usage(should not be >80-85%--- NodeB Utilization/CE Utilization Report)

ronization Fail/ RNC Internal failures)-- RRC Access fails

or interference-- Cell Power Report

DL (if UL interference is not the cause)

distance area or close to cell edge area

CS Trans, Iub AAl2 fails)-----

ent of new Connection/bearer ]

Usage(shouls not be >80-85%--- NodeB Utilization/CE Utilization Report)

•Check M1005C128 CANC_ADD_SRNC_TRA

stem reset/user reset & DSP_Service_Statistics reports

or interference-- Cell Power Report

C Background or MTC Background.

active for traffic.

There could be multiple packets inside single RAB

2. If high HSDPA Access Failures_UL DCH (RNC_661c/d)

6. HSDPA setup fail due RNC internal reason

_by_Code_and_Modulation_Usage reports •HSDPA Acces

Missing neighbor checks-- for neighbor optimization

_UL DCH (RNC_661c/d)

guration failure rate-- terminal problem-- RRC signalling report

el resources (check CE resource utilisation using M5001 counters at BH)

UL DCH Selected due to too many HSUPA users

arer due the

ion (related to HSDPA UL return channel)

ed due too many HSDPA users

• Voice Drops due to Iur

• Voice Drops due to BTS

• Voice Drops due to RNC

• Voice Drops due to UE