GATE PATHSHALA Educational Services Llp. ( www.gatepathshala.

com )
Offers: GATE Aerospace Engineering Classes, Study Material, Online Test Series & Interview Guidance

The NACA airfoil series

The early NACA airfoil series, the 4-digit, 5-digit, and modified 4-/5-digit, were generated using
analytical equations that describe the camber (curvature) of the mean-line (geometric centerline) of
the airfoil section as well as the section's thickness distribution along the length of the airfoil. Later
families, including the 6-Series, are more complicated shapes derived using theoretical rather than
geometrical methods. Before the National Advisory Committee for Aeronautics (NACA) developed
these series, airfoil design was rather arbitrary with nothing to guide the designer except past
experience with known shapes and experimentation with modifications to those shapes.

This methodology began to change in the early 1930s with the publishing of a NACA report entitled
The Characteristics of 78 Related Airfoil Sections from Tests in the Variable Density Wind Tunnel.
In this landmark report, the authors noted that there were many similarities between the airfoils that
were most successful, and the two primary variables that affect those shapes are the slope of the
airfoil mean camber line and the thickness distribution above and below this line. They then
presented a series of equations incorporating these two variables that could be used to generate an
entire family of related airfoil shapes. As airfoil design became more sophisticated, this basic
approach was modified to include additional variables, but these two basic geometrical values
remained at the heart of all NACA airfoil series, as illustrated below.

NACA airfoil geometrical construction

NACA Four-Digit Series:

The first family of airfoils designed using this approach became known as the NACA Four-Digit
Series. The first digit specifies the maximum camber (m) in percentage of the chord (airfoil length),
the second indicates the position of the maximum camber (p) in tenths of chord, and the last two
numbers provide the maximum thickness (t) of the airfoil in percentage of chord. For example, the
NACA 2415 airfoil has a maximum thickness of 15% with a camber of 2% located 40% back from
the airfoil leading edge (or 0.4c). Utilizing these m, p, and t values, we can compute the coordinates
for an entire airfoil using the following relationships:

1. Pick values of x from 0 to the maximum chord c.

2. Compute the mean camber line coordinates by plugging the values of m and p into the
following equations for each of the x coordinates.
 GATE PATHSHALA Educational Services Llp. ( www.gatepathshala.com )
Offers: GATE Aerospace Engineering Classes, Study Material, Online Test Series & Interview Guidance

where
x = coordinates along the length of the airfoil, from 0 to c (which stands for chord, or length)
y = coordinates above and below the line extending along the length of the airfoil, these are
either yt for thickness coordinates or yc for camber coordinates
t = maximum airfoil thickness in tenths of chord (i.e. a 15% thick airfoil would be 0.15)
m = maximum camber in tenths of the chord
p =position of the maximum camber along the chord in tenths of chord

3. Calculate the thickness distribution above (+) and below (-) the mean line by plugging the
value of t into the following equation for each of the x coordinates.

4. Determine the final coordinates for the airfoil upper surface (xU, yU) and lower surface (xL, yL)
using the following relationships.

NACA Five-Digit Series:

The NACA Five-Digit Series uses the same thickness forms as the Four-Digit Series but the mean
camber line is defined differently and the naming convention is a bit more complex. The first digit,
when multiplied by 3/2, yields the design lift coefficient (cl) in tenths. The next two digits, when
divided by 2, give the position of the maximum camber (p) in tenths of chord. The final two digits
again indicate the maximum thickness (t) in percentage of chord. For example, the NACA 23012
has a maximum thickness of 12%, a design lift coefficient of 0.3, and a maximum camber located
15% back from the leading edge. The steps needed to calculate the coordinates of such an airfoil
are:

1. Pick values of x from 0 to the maximum chord c.

2. Compute the mean camber line coordinates for each x location using the following equations,
and since we know p, determine the values of m and k1 using the table shown below.

3. Calculate the thickness distribution using the same equation as the Four-Digit Series.
 GATE PATHSHALA Educational Services Llp. ( www.gatepathshala.com )
Offers: GATE Aerospace Engineering Classes, Study Material, Online Test Series & Interview Guidance

4. Determine the final coordinates using the same equations as the Four-Digit Series.

Modified NACA Four- and Five-Digit Series:

The airfoil sections you mention for the B-58 bomber are members of the Four-Digit Series, but the
names are slightly different as these shapes have been modified. Let us consider the root section,
the NACA 0003.46-64.069, as an example. The basic shape is the 0003, a 3% thick airfoil with 0%
camber. This shape is a symmetrical airfoil that is identical above and below the mean camber line.
The first modification we will consider is the 0003-64. The first digit following the dash refers to the
roundedness of the nose. A value of 6 indicates that the nose radius is the same as the original
airfoil while a value of 0 indicates a sharp leading edge. Increasing this value specifies an
increasingly more rounded nose. The second digit determines the location of maximum thickness in
tenths of chord. The default location for all four- and five-digit airfoils is 30% back from the leading
edge. In this example, the location of maximum thickness has been moved back to 40% chord.
Finally, notice that the 0003.46-64.069 features two sets of digits preceeded by decimals. These
merely indicate slight adjustments to the maximum thickness and location thereof. Instead of being
3% thick, this airfoil is 3.46% thick. Instead of the maximum thickness being located at 40% chord,
the position on this airfoil is at 40.69% chord. To compute the coordinates for a modified airfoil
shape:

1. Pick values of x from 0 to the maximum chord c.

2. Compute the mean camber line coordinates using the same equations provided for the Four-
or Five-Digit Series as appropriate.
3. Calculate the thickness distribution above (+) and below (-) the mean line using these
equations. The values of the ax and dx coefficients are determined from the following table
(these are derived for a 20% thick airfoil).

4. Determine the "final" coordinates using the same equations as the Four-Digit Series.
5. As noted above, this procedure yields a 20% thick airfoil. To obtain the desired thickness,
simply scale the airfoil by multiplying the "final" y coordinates by [t / 0.2].

NACA 1-Series or 16-Series:

Unlike those airfoil families discussed so far, the 1-Series was developed based on airfoil theory
rather than on geometrical relationships. By the time these airfoils were designed during the late
1930s, many advances had been made in inverse airfoil design methods. The basic concept behind
this design approach is to specify the desired pressure distribution over the airfoil (this distribution
dictates the lift characteristics of the shape) and then derive the geometrical shape that produces
 GATE PATHSHALA Educational Services Llp. ( www.gatepathshala.com )
Offers: GATE Aerospace Engineering Classes, Study Material, Online Test Series & Interview Guidance

this pressure distribution. As a result, these airfoils were not generated using some set of analytical
expressions like the Four- or Five-Digit Series. The 1-Series airfoils are identified by five digits, as
exemplified by the NACA 16-212. The first digit, 1, indicates the series (this series was designed for
airfoils with regions of barely supersonic flow). The 6 specifies the location of minimum pressure in
tenths of chord, i.e. 60% back from the leading edge in this case. Following a dash, the first digit
indicates the design lift coefficient in tenths (0.2) and the final two digits specify the maximum
thickness in tenths of chord (12%). Since the 16-XXX airfoils are the only ones that have ever seen
much use, this family is often referred to as the 16-Series rather than as a subset of the 1-Series.

NACA 6-Series:
Although NACA experimented with approximate theoretical methods that produced the 2-Series
through the 5-Series, none of these approaches was found to accurately produce the desired airfoil
behavior. The 6-Series was derived using an improved theoretical method that, like the 1-Series,
relied on specifying the desired pressure distribution and employed advanced mathematics to
derive the required geometrical shape. The goal of this approach was to design airfoils that
maximized the region over which the airflow remains laminar. In so doing, the drag over a small
range of lift coefficients can be substantially reduced. The naming convention of the 6-Series is by
far the most confusing of any of the families discussed thus far, especially since many different
variations exist. One of the more common examples is the NACA 641-212, a=0.6.
In this example, 6 denotes the series and indicates that this family is designed for greater laminar
flow than the Four- or Five-Digit Series. The second digit, 4, is the location of the minimum pressure
in tenths of chord (0.4c). The subscript 1 indicates that low drag is maintained at lift coefficients 0.1
above and below the design lift coefficient (0.2) specified by the first digit after the dash in tenths.
The final two digits specify the thickness in percentage of chord, 12%. The fraction specified by
a=___ indicates the percentage of the airfoil chord over which the pressure distribution on the airfoil
is uniform, 60% chord in this case. If not specified, the quantity is assumed to be 1, or the
distribution is constant over the entire airfoil.

NACA 7-Series:
The 7-Series was a further attempt to maximize the regions of laminar flow over an airfoil
differentiating the locations of the minimum pressure on the upper and lower surfaces. An example
is the NACA 747A315. The 7 denotes the series, the 4 provides the location of the minimum
pressure on the upper surface in tenths of chord (40%), and the 7 provides the location of the
minimum pressure on the lower surface in tenths of chord (70%). The fourth character, a letter,
indicates the thickness distribution and mean line forms used. A series of standaradized forms
derived from earlier families are designated by different letters. Again, the fifth digit incidates the
design lift coefficient in tenths (0.3) and the final two integers are the airfoil thickness in perecentage
of chord (15%).

NACA 8-Series:
A final variation on the 6- and 7-Series methodology was the NACA 8-Series designed for flight at
supercritical speeds. Like the earlier airfoils, the goal was to maximize the extent of laminar flow on
the upper and lower surfaces independently. The naming convention is very similar to the 7-Series,
an example being the NACA 835A216. The 8 designates the series, 3 is the location of minimum
pressure on the upper surface in tenths of chord (0.3c), 5 is the location of minimum pressure on
the lower surface in tenths of chord (50%), the letter A distinguishes airfoils having different camber
or thickness forms, 2 denotes the design lift coefficient in tenths (0.2), and 16 provides the airfoil
thickness in percentage of chord (16%).
 GATE PATHSHALA Educational Services Llp. ( www.gatepathshala.com )
Offers: GATE Aerospace Engineering Classes, Study Material, Online Test Series & Interview Guidance

Summary:
Though we have introduced the primary airfoil families developed in the United States before the
advent of supersonic flight, we haven't said anything about their uses. So let's briefly explore the
advantages, disadvantages, and applications of each of these families.

Family Advantages Disadvantages Applications

4-Digit 1. Good stall characteristics 1. Low maximum lift coefficient 1. General aviation
2. Horizontal tails
2. Small center of pressure movement 2. Relatively high drag
across large speed range Symmetrical:
3. High pitching moment
3. Roughness has little effect 3. Supersonic jets
4. Helicopter blades
5. Shrouds
6. Missile/rocket fins
5-Digit 1. Higher maximum lift coefficient 1. Poor stall behavior 1. General aviation
2. Piston-powered bombers,
transports
2. Low pitching moment 2. Relatively high drag
3. Commuters
4. Business jets
3. Roughness has little effect
16-Series 1. Avoids low pressure peaks 1. Relatively low lift 1. Aircraft propellers
2. Ship propellers
2. Low drag at high speed
6-Series 1. High maximum lift coefficient 1. High drag outside of the 1. Piston-powered fighters
optimum range of operating 2. Business jets
conditions 3. Jet trainers
2. Very low drag over a small range of
4. Supersonic jets
operating conditions
2. High pitching moment
3. Optimized for high speed
3. Poor stall behavior

4. Very susceptible to roughness

7-Series 1. Very low drag over a small range of 1. Reduced maximum lift Seldom used
operating conditions coefficient

2. Low pitching moment 2. High drag outside of the

optimum range of operating
conditions

3. Poor stall behavior

4. Very susceptible to roughness

8-Series Unknown Unknown Very seldom used

Today, airfoil design has in many ways returned to an earlier time before the NACA families were
created. The computational resources available now allow the designer to quickly design and
optimize an airfoil specifically tailored to a particular application rather than making a selection from
an existing family.