Micropilot FMR51 FMR52 TI

Technical Information
Micropilot FMR51, FMR52

Level radar
Level measurement in liquids
Application • Pressure range: –1 to +16 bar (–14.5 to +232 psi)

• Accuracy: ± 2 mm
Continuous, non-contact level measurement of liquids,
pastes and slurries
Your benefits
Features FMR51:
• Premium device for level measurements even under • Reliable measurement even for changing product and
extreme conditions process conditions
• Maximum measuring range: 40 m (131 ft); for • Integrated data memory (HistoROM) for high
version with enhanced dynamics: 70 m (230 ft) availability
• Process connection: 1½" thread/Tri-Clamp/flange • Intuitive operating menu in national languages for
• Temp. range: –196 to +450 °C (–321 to +842 °F) easy commissioning
• Pressure range: –1 to +160 bar (–14.5 to +2 320 psi) • Simple integration into control or asset management
• Accuracy: ± 2 mm systems
• Exact diagnostic and process information to assist fast
Features FMR52:
decisions
• Premium device for aggressive media as well as for
• International approvals for use in hazardous areas
highest hygiene requirements
• 5-point linearity protocol
(ASME BPE, USP Class VI)
• WHG and marine approvals
• Flush mounted, completely filled PTFE horn antenna
• SIL2 according to IEC 61508, SIL3 in case of
• Maximum measuring range: 40 m (131 ft); for
homogeneous or heterogeneous redundancy
version with enhanced dynamics: 60 m (197 ft)
• System integration via HART/PROFIBUS PA (Profile
• Process connection: Flush mounted with cladded
3.02)/FOUNDATION Fieldbus
flange; process connections for hygiene requirements
(Tri-Clamp, DIN 11851)
• Temp. range: –40 to +200 °C (–40 to +392 °F)
TI01040F/00/EN/01.12
71162672
Table of contents Micropilot FMR51, FMR52
Table of contents
Important document information . . . . . . . . . . . . . . . . 4 Degree of protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

Document conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Vibration resistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Cleaning the antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Electromagnetic compatibility (EMC) . . . . . . . . . . . . . . . . . 59
Function and system design . . . . . . . . . . . . . . . . . . . . 6
Measuring principle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Process temperature range . . . . . . . . . . . . . . . . . . . . . . . . 60
Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Process pressure range . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Measured variable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Dielectric constant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Measuring range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Operating frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Transmitting power . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Mechanical construction . . . . . . . . . . . . . . . . . . . . . 61
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Output signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Signal on alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Linearization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Operability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Galvanic isolation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Operating concept . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Protocol-specific data . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Local operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Operation with remote display and operating module FHX50 . . 72
Remote operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Integration in tank gauging system . . . . . . . . . . . . . . . . . . . 76
Terminal assignment . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
System integration via Fieldgate . . . . . . . . . . . . . . . . . . . . . 77
Device plug connectors . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Supply voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Power consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Certificates and approvals . . . . . . . . . . . . . . . . . . . . 78
Current consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 CE mark . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Power supply failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 C-Tick symbol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Potential equalization . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Ex approval . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Dual seal according to ANSI/ISA 12.27.01 . . . . . . . . . . . . . . 78
Cable entries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Functional Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Cable specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Sanitary compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Overvoltage protection . . . . . . . . . . . . . . . . . . . . . . . . . . 31 AD2000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Pressure Equipment Directive . . . . . . . . . . . . . . . . . . . . . . 78
Marine certificate (in preparation) . . . . . . . . . . . . . . . . . . . 78
Performance characteristics . . . . . . . . . . . . . . . . . . . 32
Radio standard EN302729-1/2 . . . . . . . . . . . . . . . . . . . . . 78
Reference operating conditions . . . . . . . . . . . . . . . . . . . . . 32
Radio standard EN302372-1/2 . . . . . . . . . . . . . . . . . . . . . 79
Maximum measured error . . . . . . . . . . . . . . . . . . . . . . . . 32
FCC / Industry Canada . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Measured value resolution . . . . . . . . . . . . . . . . . . . . . . . . 33
CRN approval . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Reaction time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Track record . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Influence of ambient temperature . . . . . . . . . . . . . . . . . . . 33
Other standards and guidelines . . . . . . . . . . . . . . . . . . . . . 80
Influence of gas layer . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Gas phase compensation with external pressure sensor
(PROFIBUS PA, in preparation) . . . . . . . . . . . . . . . . . . . . . 34 Ordering information . . . . . . . . . . . . . . . . . . . . . . . . 81
Ordering information . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
5-point linearity protocol (in preparation) . . . . . . . . . . . . . . . 81
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Customized parametrization . . . . . . . . . . . . . . . . . . . . . . . 82
Installation conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Measuring conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Installation in vessel (free space) . . . . . . . . . . . . . . . . . . . . 41 Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Installation in stilling well . . . . . . . . . . . . . . . . . . . . . . . . 44 Device-specific accessories . . . . . . . . . . . . . . . . . . . . . . . . 83
Installation in bypass . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 Communication-specific accessories . . . . . . . . . . . . . . . . . . 85
Vessels with heat insulation . . . . . . . . . . . . . . . . . . . . . . . 50 Service-specific accessories . . . . . . . . . . . . . . . . . . . . . . . . 86
System components . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
Environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Ambient temperature range . . . . . . . . . . . . . . . . . . . . . . . 51 Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Ambient temperature limits . . . . . . . . . . . . . . . . . . . . . . . 51 Standard documentation . . . . . . . . . . . . . . . . . . . . . . . . . 87
Storage temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 Supplementary documentation . . . . . . . . . . . . . . . . . . . . . 87
Climate class . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 Safety Instructions (XA) . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Geometric height according to IEC61010-1 Ed.3 . . . . . . . . . . 59
2 Endress+Hauser
Micropilot FMR51, FMR52 Table of contents
Registered trademarks . . . . . . . . . . . . . . . . . . . . . . . 88
Patents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Endress+Hauser 3
Important document information

Document conventions Safety symbols
Symbol Meaning
DANGER!
DANGER This symbol alerts you to a dangerous situation. Failure to avoid this situation will result in serious
A0011189-EN
or fatal injury.
WARNING!
WARNING This symbol alerts you to a dangerous situation. Failure to avoid this situation can result in serious
A0011190-EN
or fatal injury.
CAUTION!
CAUTION This symbol alerts you to a dangerous situation. Failure to avoid this situation can result in minor
A0011191-EN
or medium injury.
NOTICE!
NOTICE This symbol contains information on procedures and other facts which do not result in personal
A0011192-EN
injury.
Electrical symbols
Symbol Meaning
Direct current
A0011197 A terminal to which DC voltage is applied or through which direct current flows.
Alternating current
A0011198 A terminal to which alternating voltage is applied or through which alternating current flows.
Direct current and alternating current

A0017381 • A terminal to which alternating voltage or DC voltage is applied.
• A terminal through which alternating current or direct current flows.
Ground connection
A grounded terminal which, as far as the operator is concerned, is grounded via a grounding system.
A0011200
Protective ground connection

A terminal which must be connected to ground prior to establishing any other connections.
A0011199
Equipotential connection
A connection that has to be connected to the plant grounding system: This may be a potential
A0011201
equalization line or a star grounding system depending on national or company codes of practice.
Symbols for certain types of information
Symbol Meaning
Allowed
Indicates procedures, processes or actions that are allowed.
A0011182
Preferred
Indicates procedures, processes or actions that are preferred.
A0011183
Forbidden
Indicates procedures, processes or actions that are forbidden.
A0011184
Tip
Indicates additional information.
A0011193
Reference to documentation
Refers to the corresponding device documentation.
A0011194
4 Endress+Hauser
Symbol Meaning
Reference to page
Refers to the corresponding page number.
A0011195
Reference to graphic
Refers to the corresponding graphic number and page number.
A0011196
Symbols in graphics
Symbol Meaning
1, 2, 3 ... Item numbers

, , … Series of steps
A, B, C, ... Views
A-A, B-B, C-C, ... Sections
Hazardous area
- Indicates a hazardous area.
A0011187
Safe area (non-hazardous area)

. Indicates a non-hazardous location.
A0011188
Symbols at the device
Symbol Meaning
Safety instructions
Observe the safety instructions contained in the associated Operating Instructions.
Temperature resistance of the connection cables

Specifies the minimum value of the temperature resistance of the connection cables.
Endress+Hauser 5
Function and system design

Measuring principle The Micropilot is a "downward-looking" measuring system, operating based on the time-of-flight method
(ToF). It measures the distance from the reference point (process connection) to the product surface. Radar
impulses are emitted by an antenna, reflected off the product surface and received again by the radar system.
100%
D
E
F
0%
A0017870
å1 Setup parameters of the Micropilot

R Reference point of the measurement (lower edge of the flange or threaded connection)
E Empty calibration ( = zero)
F Full calibration (= span)
D Measured distance
L Level (L = E - D)
Input
The reflected radar impulses are received by the antenna and transmitted into the electronics. A
microprocessor evaluates the signal and identifies the level echo caused by the reflection of the radar impulse
at the product surface. The unambiguous signal identification is accomplished by the PulseMaster® eXact
software together with the Multi-echo tracking algorithms, based on many years of experience with time-of-
flight technology.
The distance D to the product surface is proportional to the time of flight t of the impulse:
D = c · t/2,
with c being the speed of light.
Based on the known empty distance E, the level L is calculated:
L=E–D
The reference point R of the measurement is located at the process connection. For details see the
dimensional drawing:
• FMR51: (® ä 62)
• FMR52: (® ä 65)
The Micropilot is equipped with functions to suppress interference echoes. The user can activate these
functions. Together with the multi-echo tracking algorithms they ensure that interference echoes (i.e. from
edges and weld seams) are not interpreted as level echo.
6 Endress+Hauser
Output
The Micropilot is commissioned by entering an empty distance "E" (=zero), a full distance "F" (=span) and
application parameters. The application parameters are automatically adapt into the instrument to the
process conditions. For models with a current output, the factory adjustment for zero point "E" and span "F"
is 4 mA and 20 mA. For digital outputs and the display module, the factory adjustment for zero point "E" and
span "F" is 0 % and 100 %.
A linearization with max. 32 points, based on a table entered either manually or semi-automatically, can be
activated locally or remotely. This function provides a measurement in engineering units and a linear output
signal for spheres, horizontal cylindrical tanks and vessels with conical outlet.
Life cycle of the product
Engineering Procurement Installation Commissioning Operation Maintenance Retirement
A0013773-EN
å2 Life cycle
Engineering
• Universal measuring principle
• Measurement unaffected by medium properties
• Hardware and software developed according to SIL IEC 61508
Procurement
• Endress+Hauser being the world market leader in level measurement guarantees asset protection
• Worldwide support and service
Installation
• Special tools are not required
• Reverse polarity protection
• Modern, detachable terminals
• Main electronics protected by a separate connection compartment
Commissioning
• Fast, menu-guided commissioning in only a few steps on site or from the control room
• Plain text display in national languages reduces the risk of error or confusion
• Direct local access of all parameters
• Short instruction manual at the device
Operation
• Multi-echo tracking: Reliable measurement through self-learning echo-search algorithms taking into
account the short-term and long-term history in order to check the found echoes for plausibility and to
suppress interference echoes.
• Diagnostics in accordance with NAMUR NE107
Maintenance
• HistoROM: Data backup for instrument settings and measured values
• Exact instrument and process diagnosis to assist fast decisions with clear details concerning remedies
• Intuitive, menu-guided operating concept in national languages saves costs for training, maintenance and
operation
• Cover of the electronics compartment can be opened in hazardous areas
Retirement
• Order code translation for subsequent models
• RoHS-conforming (Restriction of certain Hazardous Substances), unleaded soldering of electronic
components
• Environmentally sound recycling concept
Endress+Hauser 7
Input
Measured variable The measured variable is the distance between the reference point and the product surface.
Subject to the empty distance entered "E" the level is calculated.
Alternatively, the level can be converted into other variables (volume, mass) by means of linearization (32
points).
Measuring range Maximum measuring range
Device Maximum measuring range
FMR51 - standard version 40 m (131 ft)
FMR51 - with "Advanced dynamics" application package 70 m (230 ft)
FMR52 - standard version 40 m (131 ft)
FMR52 - with "Advanced dynamics" application package 60 m (197 ft)
Usable measuring range

The usable measuring range depends on the size of the antenna, the reflectivity of the medium, the
mounting location and eventual interference reflections.
The following tables describe the groups of media as well as the achievable measuring range as a function of
application and media group. If the dielectric constant of a medium is unknown, it is recommended to
assume media group B to ensure a reliable measurement.
Media groups
Media groups DK (er) Example
A 1.4 to 1.9 non-conducting liquids, e.g. liquefied gas 1)
B 1.9 to 4 non-conducting liquids, e.g. benzene, oil, toluene, …
C 4 to 10 e.g. concentrated acids, organic solvents, esters, aniline, alcohol, acetone, …
D > 10 conducting liquids, e.g. aqueous solutions, dilute acids and alkalis
1) Treat Ammonia NH3 as a medium of group A.
8 Endress+Hauser
Device Storage tank
A0018833
Calm product surface (e.g. intermittent filling, filling from bottom, immersion tubes)
Antenna size
FMR51 40 mm (1½ in) 50 mm (2 in) 80 mm (3 in) 100 mm (4 in)
FMR52 - 50 mm (2 in) 80 mm (3 in) -
A B C D A B C D A B C D A B C D
3
(9.9) 4
5 5 (13)
(16) (16)
8 8 8
8
(26) (26) (26) (26)
10 10 10
(32) 12 (32) (32)
15 15 (39) 15 15 15
(49) (49) (49) (49) (49)
25 20 25
25
(82) (65) (82)
(82)
30 30
A0018858
35 (98) (99)
(110)
40 40 40 40 40
(131) (131) (131) (131) (131)
A0018859 45
(148)
60
(197)
70
A0018860 (229)
A0018862
Measuring range [m (ft)]
Legend
Measuring range of the standard version
Measuring range for the "Advanced dynamics" application package (product structure: feature 540: "Application
Package", Option EM: "Advanced dynamics")
Endress+Hauser 9
Device Buffer tank
A0018835
Moving surfaces (e.g. continuous filling, from above, mixing jets)
Antenna size
FMR52 - 50 mm (2 in) 80 mm (3 in) -
B C D B C D A B C D A B C D
2
(6.6) 2.5
(8)
3
(9.9)
4
(13)
5 5 5 5 5
(16) (16) (16) (16) (16)
7.5 7.5 7.5

(24) (24) (24)
10 10 10 10 10 10
(32) (32) (32) (32) (32) (32)
15 15 15 15 15
A0018863
(49) (49) (49) (49) (49)
A0018864
25 25 25
(82) (82) (82)
A0018865
35
(110)
A0018866
Legend
10 Endress+Hauser
Device Process tank with agitator
A0018837
Turbulent surface. Single stage agitator (frot < 1 Hz)
Antenna size
FMR52 - 50 mm (2 in) 80 mm (3 in) -
B C D B C D B C D B C D
1
(3.2)
2 2
(6.6) (6.6)
2.5
(8.2)
3 3
(9.8) (9.8)
4
(13)
5 5 5 5
(16) (16) (16) (16)
7.5
A0018867 8 8
(25)
(26) (26) 10
10
(32) (32)
12
A0018868
(39)
15 15
(49) (49)
A0018869
20
(65)
A0018870
Legend
Endress+Hauser 11
Device Stilling well Bypass
A0018840
A0018842
Antenna size Antenna size
FMR51 40 to 100 mm ( 1½ ... 4 in) 40 to 100 mm ( 1½ ... 4 in)
FMR52 50 to 80 mm ( 2 ... 3 in) 50 to 80 mm ( 2 ... 3 in)
A, B, C, D C, D
20 20
(66) (66)
A0018851 A0018852
12 Endress+Hauser
Operating frequency K-band (~ 26 GHz)

Up to 8 Micropilot transmitters can be installed in the same tank because the transmitter pulses are
statistically coded.
Transmitting power Distance Average energy density in beam direction
Standard version With "Advanced dynamics" application

package 1)
1 m (3.3 ft) < 12 nW/cm2 < 64 nW/cm2
5 m (16 ft) < 0.4 nW/cm2 < 2.5 nW/cm2
1) Product structure, feature 540: "Application package", option EM: "Advanced dynamics"
Endress+Hauser 13
Output
Output signal HART
Signal coding FSK ±0.5 mA over current signal
Data transmission rate 1 200 Bit/s
Galvanic isolation Yes
PROFIBUS PA (in preparation)
Signal coding Manchester Bus Powered (MBP)
Data transmission rate 31.25 kBit/s, voltage mode
FOUNDATION Fieldbus (in preparation)
Signal coding Manchester Bus Powered (MBP)
Data transmission rate 31.25 kBit/s, voltage mode
Switch output
For HART devices, the switch output is available as an option. See product structure, feature 20:
"Power Supply, Output", option B: "2-wire; 4-20mA HART, switch output"
Devices with PROFIBUS PA and FOUNDATION Fieldbus always have a switch output.
Switch output
Function Open collector switching output
Switching behavior Binary (conductive or non-conductive), switches when the programmable switch point is
reached
Failure mode non-conductive
Eectrical connection values U = 10.4 to 35 VDC, I = 0 to 40 mA
Internal resistance RI < 880 W

The voltage drop at this internal resistance has to be taken into account on planning the
configuration. For example, the resulting voltage at a connected relay must be sufficient
to switch the relay.
Insulation voltage floating, Insulation voltage 1 350 VDC to power supply aund 500 VAC to ground
Switch point freely programmable, separately for switch-on and switch-off point
Switching delay freely programmable from 0 to 100 sec. , separately for switch-on and switch-off point
Number of switching cycles corresponds to the measuring cycle
Signal source • Level linearized

device variables • Distance
• Terminal voltage
• Electronic temperature
• Relative echo amplitude
• Diagnostic values, Advanced diagnostics
Number of switching cycles unlimited
14 Endress+Hauser
Signal on alarm Depending on the interface, failure information is displayed as follows:

• Current output (for HART devices)
– Failsafe mode selectable (in accordance with NAMUR Recommendation NE 43):
Minimum alarm: 3.6 mA
Maximum alarm (= factory setting): 22 mA
– Failsafe mode with user-selectable value: 3.59 to 22.5 mA
• Local display
– Status signal (in accordance with NAMUR Recommendation NE 107)
– Plain text display
• Operating tool via digital communication (HART, PROFIBUS PA, FOUNDATION Fieldbus) or service
interface (CDI)
– Status signal (in accordance with NAMUR Recommendation NE 107)
– Plain text display
Linearization The linearization function of the device allows the conversion of the measured value into any unit of length
or volume. Linearization tables for calculating the volume in cylindrical tanks are pre-programmed. Other
tables of up to 32 value pairs can be entered manually or semi-automatically.
Galvanic isolation All circuits for the outputs are galvanically isolated from each other.
Protocol-specific data HART
Manufacturer ID 17 (0x11)
Device type ID 41 (0x28)
HART specification 6.0
Device description files (DTM, Information and files under:

DD) • www.endress.com
• www.hartcomm.org
HART load Min. 250 W
HART device variables The measured values can be freely assigned to the device variables.
Measured values for PV (primary variable)
• Level linearized
• Distance
• Analog output adv. diagnostics
Measured values for SV, TV, FV (second, third and fourth variable)
• Distance
• Absolute echo amplitude
• Area of incoupling
Supported functions • Burst mode

• Additional transmitter status
Manufacturer ID 17 (0x11)
Ident number 0x1559
Profile version 3.02
GSD file Information and files under:

• www.endress.com
GSD file version • www.profibus.org
Endress+Hauser 15
Output values Analog Input:

• Distance
• Absolute echo amplitude
Digital Input:
• Extended diagnostic blocks
• Status output PFS Block
Input values Analog Output:

• Analog value from PLC (for sensor block external pressure and temperature)
• Analog value from PLC to be indicated on the display
Digital Output:
• Extended diagnostic block
• Level limiter
• Sensor block measurement on
• Sensor block save history on
• Status output
Supported functions • Identification & Maintenance

Einfachste Geräteidentifizierung seitens des Leitsystems und des Typenschildes
• Automatic Ident Number Adoption
GSD compatibility mode with respect to the preceding product Micropilot M
FMR2xx
• Physical Layer Diagnostics
Installation check of the PRFIBUS segment and the Micropilot FMR5x via the
terminal voltage and telegram surveillance.
• PROFIBUS Up-/Download
Up to 10 times faster writing and reading of parameters via PROFIBUS up-/
download
• Condensed Status
Simple and self-explanatory diagnostic information by categorization of occurring
diagnostic messages.
Manufacturer ID 0x452B48
Device type 0x1028
Device Revision 0x01
DD Revision Information and files can be found:

• www.endress.com
CFF Revision • www.fieldbus.org
Device Tester Version (ITK 6.0.1

Version)
ITK Test Campaign Number IT085300
Link Master (LAS) capable yes
Link Master / Basic Device yes; default: Basic Device

selectable
Node address Default: 247 (0xF7)
Features supported Following methods are supported:

• Restart
• ENP Restart
• Setup
• Linearization
• Self Check
Virtual Communication Relationships (VCRs)
Number of VCRs 44
Number of Link Objects in VFD 50
16 Endress+Hauser
Permanent entries 1
Client VCRs 0
Server VCRs 10
Source VCRs 43
Sink VCRs 0
Subscriber VCRs 43
Publisher VCRs 43
Device Link Capabilities
Slot time 4
Min. inter PDU delay 8
Max. response delay 20
Transducer Blocks
Block Content Output values
Setup Transducer Block Contains all parameters for a standard commissioning • Level or volume 1)
procedure (Channel 1)
• Distance (Channel 2)
Advanced Setup Transducer Contains all parameters for a more detailed configuration no output values
Block of the device
Display Transducer Block Contains all parameters for the configuration of the no output values
display module
Diagnostic Transducer Block Contains diagnostic information no output values
Expert Configuration Contains parameters which require detailed knowledge no output values
Transducer Block of the functionalities of the device
Expert Information Contains information about the state of the device no output values
Transducer Block
Service Sensor Transducer Contains parameters which can only be operated by no output values
Block Endress+Hauser service personnel
Service Information Contains information on the state of device which is no output values
Transducer Block relevant for service operations
Data Transfer Transducer Contains parameters which allow to backup the device no output values
Block configuration in the display module and to restore it into
the device.
1) depending on the configuration of the block
Function Blocks
Block Content Number of Number of Execution Functionality
permanent instantiable time
blocks blocks
Resource Block The Resource Block contains all the data 1 0 - enhanced
that uniquely identifies the field device.
It is an electronic version of a nameplate
of the device.
Multiple The AI block takes the manufacturer's 2 3 25 ms enhanced

Analog Input input data, selected by channel number,
Block and makes it available to other function
blocks at its output.
Discrete Input The DI block takes a discrete input value 1 2 20 ms standard

Block (e.g. indication of an level limit), and
makes it available to other function
blocks at its output.
Endress+Hauser 17
Block Content Number of Number of Execution Functionality

permanent instantiable time
blocks blocks
PID Block The PID block serves as proportional- 1 1 25 ms standard

integralderivative controller and is used
almost universally to do closed-loop-
control in the field including cascade and
feedforward.
Arithmetic This block is designed to permit simple 1 1 25 ms standard

Block use of popular measurement math
functions. The user does not have to
know how to write equations. The math
algorithm is selected by name, chosen by
the user for the function to be done.
Signal The signal characterizer block has two 1 1 25 ms standard

Characterizer sections, each with an output that is a
Block non-linear function of the respective
input. The non-linear function is
determined by a single look-up table
with 21 arbitrary x-y pairs.
Input Selector The input selector block provides 1 1 25 ms standard

Block selection of up to four inputs and
generates an output based on the
configured action. This block normally
receives its inputs from AI blocks. The
block performs maximum, minimum,
middle, average and ‘first good’ signal
selection.
Integrator The Integrator Function Block integrates 1 1 25 ms standard

Block a variable as a function of the time or
accumulates the counts from a Pulse
Input block. The block may be used as a
totalizer that counts up until reset or as a
batch totalizer that has a setpoint, where
the integrated or accumulated value is
compared to pre-trip and trip settings,
generating discrete signals when these
settings are reached.
Analog Alarm 1 1 25 ms standard

Block
Up to 20 blocks can be instantiated in the device altogether, including the blocks already instantiated
on delivery.
18 Endress+Hauser
Power supply
Terminal assignment 2-wire: 4-20mA HART
2- w
4-2 ire le
0 v el
H A mA
[21 RT
4-2
0m
A ]
ope
A
n Sp
a
711 re pa
HA 20mA
08x rt
xx
RT
4...
+
1 -
1 2 4 5 6
mm
2
10
+ +
–
–
4...20 mA
3 B
7 +
1-c 1 -
1 2 4 5 han
nel 4-2 2
ove 0m
[16
] rvo A
ltag
ep
rote
ctio
n
+ + 711
286
– 17
–
4...20 mA
3
A0011294
å3 Terminal assignment 2-wire; 4-20mA HART

A Without integrated overvoltage protection
B With integrated overvoltage protection
1 Active barrier with power supply (e.g. RN221N): Observe terminal voltage (® ä 27)
2 HART communication resistor (³250 W): Observe maximum load (® ä 27)
3 Connection for Commubox FXA195 or FieldXpert SFX100 (via VIATOR Bluetooth modem)
4 Analog display device: Observe maximum load (® ä 27)
5 Cable screen; observe cable specification (® ä 30)
6 Terminals for 4-20mA HART (passive)
7 Overvoltage protection module
8 Terminal for potential equalization line
9 Cable entry
Endress+Hauser 19
2-wire: 4-20mA HART, switch output
10
9
8
2- w
4-2 ire
0
HA mA
[02 RT
PF
S
A /03
] ope
n Sp
a
711 re pa
HA 20 mA
08x rt
3+ ++ xx
31 --
RT
4...
42 +
7
1 -
mm
2 6
4-
10
+ +
–
-
³250W 4...20 mA
1 2 3 4 5 B
3+ 11 +
3 -
4-2 4
0m +
2-c
A/ 1 -
han 4-2 2
4- [17
nel
ove FIE 0mA
] rvo LD /
ltag
ep
BU
ro S
tec
tion
+ + 711
286
– 19
-
³250W 4...20 mA
1 2 3 4 5
A0013759
å4 Terminal assignment 2-wire; 4-20mA HART, switch output

1 Active barrier with power supply (e.g. RN221N): Observe terminal voltage (® ä 27)
6 Terminals for 4-20mA HART (passive)
7 Terminals for switch output (open collector)
9 Cable entry for 4-20mA HART line
10 Cable entry for switch output line
20 Endress+Hauser
2-wire: 4-20mA HART, 4-20mA
14
13
12
2- w
4-2 ire le
0 v el
HA mA
[04 RT
4-2
0m
A /05
]
A
ope
A
n Sp
20m
a
711 re pa
HA 20mA
08x rt
xx
+
4 ...
3 -
RT
11
4 ...
4 +
1 -
mm
2
+
10
+
1 –
-
4...20 mA
9 8
+ +
2 –
-
4...20 mA
3 5 6 7 4
B
+ +
1 –
+
- 3 -
4...20 mA 4-2 4
10 0m +
9 8 2-c
A/ 1 -
han
nel 4- 2
[17
ove FIE 20mA
] rvo LD /
ltag
ep
B U
ro S
tec
tion
+ + 711
28 6
2 – 19
-
4...20 mA
3 5 6 7 4
A0013923
å5 Terminal assignment 2-wire, 4-20 mA HART, 4...20mA

1 Connection current output 2
2 Connection current output 1
3 Supply voltage for current output 1 (e.g. RN221N); Observe terminal voltage (® ä 28)
5 HART communication resistor (³ 250 W): Observe maximum load (® ä 28)
7 Analog display device ; observe maximum load (® ä 28)
8 Analog display device ; observe maximum load (® ä 28)
9 Supply voltage for current output 2 (e.g. RN221N); Obesrve terminal voltage (® ä 28)
11 Terminals for current output 2
12 Terminal for the potential equalization line
13 Cable entry for current output 1
14 Cable entry for current output 2
This version is also suited for single-channel operation. In this case, current output 1 (terminals 1 and
2) must be used.
Endress+Hauser 21
4-wire: 4-20mA HART (10.4 to 48 VDC)
13
12
11
2- w
4-2 ire
0
HA mA
[08 RT
A ]
= V
ope
48
n Sp
4...
a
711 re pa
HA 20 mA
08x rt
10.
L+ xx
1 L-
RT
4...
2 +
10 9
3 -
mm
4 8
10
7
+
-
³250W 4...20 mA
6
1 2 3 4 5
A0011340
å6 Terminal assignment 4-wire; 4-20mA HART (10.4 to 48 VDC)

1 Evaluation unit, e.g. PLC
5 Signal cable including screening (if required), observe cable specification (® ä 30)
6 Protective connection; do not disconnect!
7 Protective earth, observe cable specification (® ä 30)
8 Terminals for 4...20mA HART (active)
9 Terminals for supply voltage
10 Supply voltage: Observe terminal voltage (® ä 29), observe cable specification (® ä 30)
11 Terminal for potential equalization
12 Cable entry for signal line
13 Cable entry for power supply
!CAUTION
To ensure electrical safety:
► Do not disconnect the protective connection (7).
► Disconnect the supply voltage before disconnecting the protective earth (8).
Connect protective earth to the internal ground terminal (8) before connecting the supply voltage. If
necessary, connect the potential matching line to the external ground terminal (12).
In order to ensure electromagnetic compatibility (EMC): Do not only ground the device via the
protective earth conductor of the supply cable. Instead, the functional grounding must also be
connected to the process connection (flange or threaded connection) or to the external ground
terminal.
An easily accessible power switch must be installed in the proximity of the device. The power switch
must be marked as a disconnector for the device (IEC/EN61010).
22 Endress+Hauser
4-wire: 4-20mA HART (90 to 253 VAC)
13
12
11
2- w
4-2 ire
0
HA mA
[09 RT
A ]
~
3V
ope
n
..25
Sp
a
711 re pa
HA 20 mA
9 0.
08x rt
xx
L
1 N
RT
4...
2 +
10 9
3 -
mm
4 8
10
7
+
-
³250W 4...20 mA
6
1 2 3 4 5
A0018965
å7 Terminal assignment 4-wire; 4-20mA HART (90 to 253 VAC)

1 Evaluation unit, e.g. PLC
5 Signal cable including screening (if required), observe cable specification (® ä 30)
6 Protective connection; do not disconnect!
7 Protective earth, observe cable specification (® ä 30)
8 Terminals for 4...20mA HART (active)
9 Terminals for supply voltage
10 Supply voltage: Observe terminal voltage (® ä 29), observe cable specification (® ä 30)
11 Terminal for potential equalization
12 Cable entry for signal line
13 Cable entry for power supply
!CAUTION
To ensure electrical safety:
► Do not disconnect the protective connection (7).
► Disconnect the supply voltage before disconnecting the protective earth (8).
Connect protective earth to the internal ground terminal (8) before connecting the supply voltage. If
necessary, connect the potential matching line to the external ground terminal (12).
In order to ensure electromagnetic compatibility (EMC): Do not only ground the device via the
protective earth conductor of the supply cable. Instead, the functional grounding must also be
connected to the process connection (flange or threaded connection) or to the external ground
terminal.
An easily accessible power switch must be installed in the proximity of the device. The power switch
must be marked as a disconnector for the device (IEC/EN61010).
Endress+Hauser 23
PROFIBUS PA / FOUNDATION Fieldbus (in preparation)
2-
F4IEwire
-20L lev
mD
ABU el
FA
P IE/F S
06/ LD
[2 F B PFS
A 07]
2 U S
op en Sp
a
7110 re pa
US
0283x4 rt
3+ ++ x5x7
B
31 --
/LFDF
PIAE
42 +
F
2
1 2-
mm
4-
10
3
1
B
3+ 6 +
3 -
4-2 4 +
0m
2-c
A/ 1 -
han
nel 4-2 2
4- [17
]
ove
rvo
FIE 0mA
LD /
ltag BU
1 ep
rote S
ctio
n
711
286
19
A0011341
å8 Terminal assignment PROFIBUS PA / FOUNDATION Fieldbus

1 Cable screen: Observe cable specifications (® ä 30)
2 Terminals for switch output (open collector)
3 Terminals PROFIBUS PA / FOUNDATION Fieldbus
5 Cable entries
24 Endress+Hauser
Connection examples for the switch output

For HART devices, the switch output is available as an option. See product structure, feature 20:
"Power Supply, Output", option B: "2-wire; 4-20mA HART, switch output"
Devices with PROFIBUS PA and FOUNDATION Fieldbus always have a switch output.
+
1
3+ 2
3+
+
-
4-
4-
A0015909 A0015910
å9 Connection of a relay å 10 Connection of a digital input

1 Pull-up resistor
Suitable relays (examples):
2 Digital input
• Solid-state relay: Phoenix Contact OV-24DC/480AC/5 with mounting
rail connector UMK-1 OM-R/AMS
• Electromechanical relay: Phoenix Contact PLC-RSC-12DC/21
Endress+Hauser 25
Device plug connectors For the versions with fieldbus plug connector (M12 or 7/8"), the signal line can be connected without
opening the housing.
Pin assignment of the M12 plug connector

Pin Meaning
1 Signal +
4 3 –
2 not connected
1 + 2 nc 3 Signal -
4 Ground
A0011175
Pin assignment of the 7/8" plug connector

Pin Meaning
1 3 1 Signal -
2 Signal +
2 4 3 Screen
4 Not connected
A0011176
26 Endress+Hauser
Supply voltage An external power supply is required.

Various supply units can be ordered from Endress+Hauser: see "Accessories" section (® ä 86)
2-wire, 4-20mA HART, passive
"Power Supply, "Approval" 2) Terminal voltage U at Maximum load R, depending on the supply voltage U0 at the
Output" 1) the device supply unit
A: 2-wire; 4-20mA HART • Non-Ex 10.4 to 35 V 3) R [?]

• Ex nA
• Ex ic 500
• CSA GP
Ex ia / IS 10.4 to 30 V 3)
0
10 20 30 35 U0 [V]
10.4 21.4
A0017140
4)
• Ex d(ia) / XP 12 to 35 V R [W]
• Ex ic(ia)
• Ex nA(ia) 500
• Ex ta / DIP
Ex ia + Ex d(ia) / IS + XP 12 to 30 V 4)
0
10 20 30 35 U0 [V]
12 23
A0019136
1) Feature 020 of the product structure

3) For ambient temperatures Ta £ -20 °C (-4 °F) a minimum voltage of 15 V is required for the sartup of the device at the MIN error current (3,6 mA). The
startup current can be parametrized. If the device is operated with a fixed current I ³ 5,5 mA (HART multidrop mode), a voltage of U ³ 10,4 V is sufficient
throughout the entire range of ambient temperatures.
4) For ambient temperatures Ta £ -20 °C (-4 °F) a minimum voltage of 16 V is required for the satrtup of the device at the MIN error current (3.6 mA).
"Power Supply, Output" 1) "Approval" 2) Terminal voltage U at Maximum load R, depending on the supply voltage U0 at the
the device supply unit
B: 2-wire; 4-20 mA HART, • Non-Ex 12 to 35 V 3) R [W]

switch output • Ex nA
• Ex nA(ia) 500
• Ex ic
• Ex ic(ia)
• Ex d(ia) / XP
• Ex ta / DIP
• CSA GP
• Ex ia / IS 12 to 30 V 3)
0
• Ex ia + Ex d(ia) / IS + XP
10 20 30 35 U0 [V]
12 23
A0019136

Endress+Hauser 27
"Power Supply, Output" 1) "Approval" 2) Terminal voltage U at the Maximum load R, depending on the supply voltage U0 at the
device supply unit
C: 2-wire; 4-20mA HART, 4-20mA any 12 to 30 V 3) R [?]
500
0
10 20 30 U0 [V]
12 23
A0017055

Polarity reversal protection Yes
Admissible residual ripple USS < 1 V

at f = 0 to 100 Hz
Admissible residual ripple USS < 10 mV

at f = 100 to 10000 Hz
28 Endress+Hauser
4-wire, 4-20mA HART, active
"Power supply; Output" 1) Terminal voltage Maximum load Rmax
K: 4-wire 90-253VAC; 4-20mA HART 90 to 253 VAC (50 to 60 Hz), 500 Ω

overvoltage category II
L: 4-wire 10,4-48VDC; 4-20mA HART 10.4 to 48 VDC
PROFIBUS PA, FOUNDATION Fieldbus (in preparation)
"Power supply; Output" 1) "Approval" 2) Terminal voltage

3)
E: 2-wire; FOUNDATION Fieldbus, switch output • Non-Ex 9 to 32 V
G: 2-wire; PROFIBUS PA, switch output • Ex nA
• Ex nA(ia)
• Ex ic
• Ex ic(ia)
• Ex d(ia) / XP
• Ex ta / DIP
• CSA GP
3)
• Ex ia / IS 9 to 30 V
• Ex ia + Ex d(ia) / IS + XP

3) Input voltages up to 35 V will not spoil the device.
Polarity sensitive No
FISCO/FNICO compliant Yes

according to IEC 60079-27
Power consumption "Power supply; Output" 1) Power consumption
A: 2-wire; 4-20mA HART < 0.9 W
B: 2-wire; 4-20mA HART, switch output < 0.9 W
C: 2-wire; 4-20mA HART, 4-20mA < 2 x 0.7 W
K: 4-wire 90-253VAC; 4-20mA HART 6 VA
L: 4-wire 10,4-48VDC; 4-20mA HART 1.3 W
Current consumption HART
Nominal current 3.6 to 22 mA, the start-up current for multidrop mode can be parametrized (is set to
3.6 mA on delivery)
Breakdown signal adjustable: 3.59 to 22.5 mA

(NAMUR NE43)
Nominal current 14 mA
Error current FDE (Fault 0 mA

Disconnection Electronic)
Endress+Hauser 29
Device basic current 14 mA
Error current FDE (Fault 0 mA

Disconnection Electronic)
FISCO (in preparation)
Ui 17.5 V
Ii 550 mA
Pi 5.5 W
Ci 5 nF
Li 10 mH
Power supply failure • Configuration is retained in the HistoROM (EEPROM).

• Error messages (incl. value of operated hours counter) are stored.
Potential equalization No special measures for potential equalization are required.

If the device is designed for hazardous areas, observe the information in the documentation "Safety
Instructions" (XA, ZD).
Terminals • Without integrated overvoltage protection

Plug-in spring terminals for wire cross-sections 0.5 to 2.5 mm2 (20 to 14 AWG)
• With integrated overvoltage protection
Screw terminals for wire cross-sections 0.2 to 2.5 mm2 (24 to 14 AWG)
Cable entries • Cable gland (not for Ex d):

– Plastics M20x1.5 for cable Æ 5 to 10 mm (0.2 to 0.39 in): non-Ex, ATEX/IECEx/NEPSI Ex ia/ic
– Metal M20x1.5 for cable Æ 7 to 10 mm (0.28 to 0.39 in): dust-Ex, FM IS, CSA IS, CSA GP, Ex nA
• Thread for cable entry:
– ½" NPT
– G ½"
– M20 × 1.5
• Connector (only for non-Ex, Ex ic, Ex ia): M12 or 7/8"
Cable specification • Standard device cable is sufficient for the power supply of the device.
• Minimum cross-section: (® ä 30)
• For ambient temperature TU³60 °C (140 °F): use cable for temperature TU +20 K.
HART
• A normal device cable suffices if only the analog signal is used.
• A shielded cable is recommended if using the HART protocol. Observe grounding concept of the plant.
PROFIBUS (in preparation)

Use a twisted, screened two-wire cable, preferably cable type A.
For further information on the cable specifications, see Operating Instructions BA00034S "Guidelines
for planning and commissioning PROFIBUS DP/PA", PNO Guideline 2.092 "PROFIBUS PA User and
Installation Guideline" and IEC61158-2 (MBP).

Endress+Hauser recommends using twisted, shielded two-wire cables.
For further information on the cable specifications, see Operating Instructions BA00013S
"FOUNDATION Fieldbus Overview", FOUNDATION Fieldbus Guideline and IEC 61158-2 (MBP).
30 Endress+Hauser
Overvoltage protection If the measuring device is used for level measurement in flammable liquids which requires the use of
overvoltage protection according to DIN EN 60079-14, standard for test procedures 60060-1 (10 kA, pulse
8/20 ms), overvoltage protection has to be ensured by an integrated or external overvoltage protection
module.
Integrated overvoltage protection

An integrated overvoltage protection module is available for 2-wire HART as well as PROFIBUS PA and
FOUNDATION Fieldbus devices.
Product structure: Feature 610 "Accessory mounted", option NA "Overvoltage protection".
Technical data
Resistance per channel 2 * 0.5 W max
Threshold DC voltage 400 to 700 V
Threshold impulse voltage < 800 V
Capacitance at 1 MHz < 1.5 pF
Nominal arrest impulse voltage (8/20 ms) 10 kA
External overvoltage protection

HAW562 or HAW569 from Endress+Hauser are suited as external overvoltage protection.
For detailed information please refer to the following documents:
• HAW562: TI01012K
• HAW569: TI01013K
Endress+Hauser 31
Performance characteristics
Reference operating • Temperature = +24 °C (+75 °F) ±5 °C (±9 °F)
conditions • Pressure = 960 mbar abs. (14 psia) ±100 mbar (±1.45 psi)
• Humidity = 60 % ±15 %
• Reflector: metal plate with a minimum diameter of 1 m (40 in)
• No major interference reflections inside the signal beam
Maximum measured error Typical data under reference operating conditions: DIN EN 61298-2, percentage values in relation to the
span.
Device Value Output
digital analog 1)
FMR50/FMR51 Sum of non-linearity, ± 2 mm (0.08 in) ± 0.02 %

Standard version nonrepeatability and
hysteresis
Offset/Zero ± 4 mm (0.2 in) ± 0.03 %
FMR50/FMR51 Sum of non-linearity, ± 3 mm (0.12 in) ± 0.02 %

Version with application package "Advanced nonrepeatability and
dynamics" 2) hysteresis
Offset/Zero ± 4 mm (0.2 in) ± 0.03 %
1) Add error of the analogous value to the digital value.

2) Product structure: Feature 540 "Application Package", Option EM "Advanced dynamics"
Differing values in near-range applications

R
4 (0.16)
D [mm] ([in])
2 (0.08)
0
-2 (-0.08)
-4 (-0.16)
0 A 1 (3.3) D [m] ([ft])

A0019035
å 11 Maximum measured error in near-range applications; values for standard version

D Maximum measured error
D Distance from the reference point R
A Lower edge of the antenna
32 Endress+Hauser
R
20 (0.79)
D [mm] ([in])
3 (0.12)
0
-3 (-12)
-20 (-0.79)
0 A 2 (6.6) D [m] ([ft])

A0019034
å 12 Maximum measured error in near-range applications; values for version with the "Advanced dynamics"
application package
D Maximum measured error
D Distance from the reference point R
A Lower edge of the antenna
Measured value resolution Dead band according to EN61298-2:

• digital: 1 mm
• analog: 1 mA
Reaction time The reaction time can be parametrized. The following step response times (as per DIN EN 61298-2) 1)are
valid if the damping is switched off:
Tank height Sampling rate Step response time
< 10 m (33 ft) ³ 3.6 s–1 < 0.8 s
< 70 m (230 ft) ³ 2.2 s–1 <1s
Influence of ambient The measurements are carried out in accordance with EN 61298-3
temperature • Digital (HART, PROFIBUS PA):
– Standard version: average TK = 2 mm/10 K; maximum 5 mm
– Version with advanced dynamics 2): average TK = 5 mm/10 K; maximum 15 mm
• Analog (current output):
– zero point (4 mA): average TK = 0.02 %/10 K
– span (20 mA): average TK = 0.05 %/10 K
Influence of gas layer High pressures reduce the propagation velocity of the measuring signals in the gas/vapor above the fluid.
This effect depends on the kind of gas/vapor and of its temperature. This results in a systematic measuring
error that gets bigger as the distance increases between the reference point of the measurement (flange) and
1) According to DIN EN 61298-2 the response time is the time which passes after a sudden change of the input signal until the output signal for the first time
assumes 90% of the steady-state value.
2) Feature 540 "Application Package", option EM
Endress+Hauser 33
the product surface. The following table illustrates this measured error for a few typical gases/vapors (with
regard to distance; a positive value means that too large a distance is being measured):
Gas layer Temperature Pressure
°C °F 1 bar (14,5 psi) 10 bar (145 psi) 50 bar (725 psi) 100 bar (1450 psi) 160 bar (2320 psi)
Air/ 20 68 0.00 % 0.22 % 1.2 % 2.4 % 3.89 %

Nitrogen
200 392 –0.01 % 0.13 % 0.74 % 1.5 % 2.42 %
400 752 –0.02 % 0.08 % 0.52 % 1.1 % 1.70 %
Hydrogen 20 68 –0.01 % 0.10 % 0.61 % 1.2 % 2.00 %
200 392 –0.02 % 0.05 % 0.37 % 0.76 % 1.23 %
400 752 –0.02 % 0.03 % 0.25 % 0.53 % 0.86 %
Water 100 212 0.02 % - - - -

(saturated
steam) 180 356 - 2.1 % - - -
263 505,4 - - 8.6 % - -
310 590 - - - 22 % -
364 687 - - - - 41.8 %
When the pressure is known and constant, this measured error can, for example, be compensated by
means of a linearization.
Gas phase compensation with PROFIBUS devices can receive the signal of an external pressure sensor through the bus and use it to
external pressure sensor perform a pressure dependent time-of-flight correction. In the case of saturated steam in the temperature
(PROFIBUS PA, in range from 100 to 350 °C (212 to 662 °f), for example, the measuring error of the distance measurement
preparation) can be reduced by this method from up to 29 % (without compensation) to less than 3 % (with
compensation).
34 Endress+Hauser
Installation
Installation conditions Mounting position
• Recommended distance A from wall to outer

edge of nozzle: ~ 1/6 of tank diameter.
1 2 3 Nevertheless the device should not be installed
closer than 15 cm (5.91 in) to the tank wall.
• Not in the center (2), as interference can cause
signal loss.
• Not above the fill stream (3).
• It is recommended to us a weather protection
cover (1) in order to protect the device from
direct sun or rain.
A
A0016882
Vessel installations
Avoid any installations (limit switches, temperature

sensors, braces, vacuum rings, heating coils, baffles
etc.) inside the signal beam. Take into account the
beam angle (® ä 38):
A0018944
Endress+Hauser 35
Reduction of interference echoes
Metallic screens mounted at a slope spread the

radar signal and can, therefore, reduce
interference echoes.
A0016890
Measurement in a plastic vessel

If the outer wall of the vessel is made of a non-conductive material (e.g. GRP), microwaves can also be
reflected off interfering installations outside the signal beam (e.g. metallic pipes (1), ladders (2), grates
(3), ...). Therefore, there should be no such interfering installations in the signal beam. Please contact
Endress+Hauser for further information.
3
1
A0017123
36 Endress+Hauser
Optimization options
• Antenna size
The bigger the antenna, the smaller the beam angle a and the fewer interference echoes (® ä 38).
• Mapping
The measurement can be optimized by means of electronic suppression of interference echoes.
• Antenna alignment
Take into account the marker on the flange or threaded connection (® ä 41) (® ä 43) .
• Stilling well
A stilling well can be applied to avoid interferences (® ä 44).
• Metallic screens mounted at a slope
They spread the radar signals and can, therefore, reduce interference echoes.
Endress+Hauser 37
Beam angle
a
W = 2 . D . tan _
2
D
a
A0016891
å 13 Relationship between beam angle a, distance D and beamwidth diameter W
The beam angle is defined as the angle a where the energy density of the radar waves reaches half the value
of the maximum energy density (3-dB-width). Microwaves are also emitted outside the signal beam and can
be reflected off interfering installations.
Beam diameter W as a function of beam angle a and measuring distance D:
FMR51
Antenna size 40 mm (1½ in) 50 mm (2 in) 80 mm (3 in) 100 mm (4 in)
Beam angle a 23° 18° 10° 8°
Measuring Beamwidth diameter W

distance (D)
3 m (9.8 ft) 1.22 m (4 ft) 0.95 m (3.1 ft) 0.53 m (1.7 ft) 0.42 m (1.4 ft)
6 m (20 ft) 2.44 m (8 ft) 1.9 m (6.2 ft) 1.05 m (3.4 ft) 0.84 m (2.8 ft)
9 m (30 ft) 3.66 m (12 ft) 2.85 m (9.4 ft) 1.58 m (5.2 ft) 1.26 m (4.1 ft)
12 m (39 ft) 4.88 m (16 ft) 3.80 m (12 ft) 2.1 m (6.9 ft) 1.68 m (5.5 ft)
15 m (49 ft) 6.1 m (20 ft) 4.75 m (16 ft) 2.63 m (8.6 ft) 2.10 m (6.9 ft)
20 m (66 ft) 8.14 m (27 ft) 6.34 m (21 ft) 3.50 m (11 ft) 2.80 m (9.2 ft)
25 m (82 ft) 10.17 m (33 ft) 7.92 m (26 ft) 4.37 m (14 ft) 3.50 m (11 ft)
30 m (98 ft) - 9.50 m (31 ft) 5.25 m (17 ft) 4.20 m (14 ft)
35 m (115 ft) - 11.09 m (36 ft) 6.12 m (20 ft) 4.89 m (16 ft)
40 m (131 ft) - 12.67 m (42 ft) 7.00 m (23 ft) 5.59 m (18 ft)
45 m (148 ft) - - 7.87 m (26 ft) 6.29 m (21 ft)
60 m (197 ft) - - 10.50 m (34 ft) 8.39 m (28 ft)
70 m (230 ft) - - - 9.79 m (32 ft)
FMR52
Antenna size 50 mm (2 in) 80 mm (3 in)
Beam angle a 18° 10°
Measuring distance (D) Beamwidth diameter W
3 m (9.8 ft) 0.95 m (3.1 ft) 0.53 m (1.7 ft)
6 m (20 ft) 1.9 m (6.2 ft) 1.05 m (3.4 ft)
38 Endress+Hauser
9 m (30 ft) 2.85 m (9.4 ft) 1.58 m (5.2 ft)
12 m (39 ft) 3.80 m (12 ft) 2.1 m (6.9 ft)
15 m (49 ft) 4.75 m (16 ft) 2.63 m (8.6 ft)
20 m (66 ft) 6.34 m (21 ft) 3.50 m (11 ft)
25 m (82 ft) 7.92 m (26 ft) 4.37 m (14 ft)
30 m (98 ft) 9.50 m (31 ft) 5.25 m (17 ft)
35 m (115 ft) 11.09 m (36 ft) 6.12 m (20 ft)
40 m (131 ft) 12.67 m (42 ft) 7.00 m (23 ft)
45 m (148 ft) - 7.87 m (26 ft)
60 m (197 ft) - 10.50 m (34 ft)
Endress+Hauser 39
Measuring conditions • In case of boiling surfaces, bubbling or tendency for foaming use FMR53 or FMR54. Depending on its
consistence, foam can either absorb microwaves or reflect them off the foam surface. Measurement is
possible under certain conditions. For FMR50, FMR51 and FMR52, the additional option "Advanced
dynamics" is recommended in these cases (feature 540: "Application Package", option EM).
• In case of heavy steam development or condensate, the maximum measuring range of FMR50,
FMR51 and FMR52 may decrease depending on density, temperature and composition of the steam ®
use FMR53 or FMR54.
• For the measurement of absorbing gases such as ammonia NH3 or some fluorocarbons 3), please use
Levelflex or Micropilot FMR54 in a stilling well.
• The measuring range begins, where the beam hits the tank bottom. Particularly with dish bottoms or
conical outlets the level cannot be detected below this point.
• For stilling well applications, the zero should be positioned at the end of the tube, as the electromagnetic
waves do not propagate completely outside the tube. It must be taken into account that the accuracy may
be reduced in the area C. In order to guarantee the required accuracy in these cases, it is recommended to
position the zero-point at a distance C above the end of the tube (see figure).
• In case of media with a low dielectric constant (er = 1.5 to 4) 4) the tank bottom can be visible through the
medium at low levels (low height C). Reduced accuracy has to be expected in this range. If this is not
acceptable, we recommend positioning the zero point at a distance C (see figure) above the tank bottom
in these applications.
• In principle it is possible to measure up to the tip of the antenna with FMR51, FMR53 and FMR54.
However, due to considerations regarding corrosion and build-up, the end of the measuring range should
not be chosen any closer than A (see figure) to the tip of the antenna.
• When using FMR54 with planar antenna, especially for media with low dielectric constants, the end of
the measuring range should not be closer than 1 m (3.28 ft) to the flange.
• The smallest possible measuring range B depends on the antenna version (see figure).
• The tank height should be at least H (see table).
A
100%
H
B
C
0%
øD
A0018872
Device A [mm (in)] B [m (ft)] C [mm (in)] H [m (ft)]
FMR51 50(1.97)
> 0.2 (0.7) 50 to 250 (1.97 to 9.84) > 0.3 (1.0)
FMR52 200(7.87)
3) Affected compounds are e.g. R134a, R227, Dymel 152a.

4) Dielectric constants of important media commonly used in the industry are summarized in the document SD106F, which can be downloaded from the
Endress+Hauser web page (www.endress.com).
40 Endress+Hauser
Installation in vessel (free Horn antenna (FMR51)

space)
Alignment
• Align the antenna vertically to the product surface.
The maximum range may be reduced if the horn antenna is not vertically aligned.
• A marking at the flange or the boss enables alignment of the antenna. This marking must be aligned
towards the tank wall.
A B
°
°
90
90
°
90
° °
°
90 90
90
90 90
° °
90 90
° °
A0018974
Nozzle mounting
The horn antenna should extend below the nozzle. Select version with antenna extension up to
500 mm (19.7 in), if necessary 5). Nozzle heights up to 500 mm (19.7 in) can be accepted if this should not
be possible due to mechanical reasons.
H
øD
A0016820
å 14 Nozzle height and diameter for horn antenna (FMR51)
Antenna size 40 mm (1½ in) 50 mm (2 in) 80 mm (3 in) 100 mm (4 in)
D 40 mm (1.57 in) 48 mm (1.89 in) 75 mm (2.95 in) 95 mm (3.74 in)
H < 85 mm (3.35 in) < 115 mm (4.53 in) < 210 mm (8.27 in) < 280 mm (11.0 in)
Please contact Endress+Hauser for applications with higher nozzle.
5) In the product structure: feature 610 "Accessory mounted", options OM, OU, OV.
Endress+Hauser 41
Threaded connection
• Tighten with the hexagonal nut only.
• Tool : Hexagonal wrench 55 mm
• Maximum permissible torque: 60 Nm (44 lbf ft)
Mesurement from the outside through plastic walls

• If possible, use an antenna 100 mm (4").
• The distance from the lower edge of the antenna to the tank ceiling should be about 100 mm (4 in).
• If possible, avoid mounting locations where condensation or build-up might occur.
• In case of outdoor mounting, the space between antenna and vessel has to be protected from the
elements.
• Do not mount any potential reflectors (e.g. pipes) outside the tank in the signal beam.
Suitable thickness of the tank ceiling:

Penetrated material PE PTFE PP Perspex
DK / er 2.3 2.1 2.3 3.1

1)
Optimum thickness 3.8 mm (0.15 in) 4.0 mm (0.16 in) 3.8 mm (0.15 in) 3.3 mm (0.13 in)
1) Other possible values for the thickness are multiples of the values listed (e.g. for PE: 7,6 mm (0.3 in), 11,4 mm
(0.45 in)
42 Endress+Hauser
Horn antenna, flush mount (FMR52)
Alignment
• Align the antenna vertically to the product surface.
The maximum range may be reduced if the horn antenna is not vertically aligned.
• A marking at the flange or the boss enables alignment of the antenna. This marking must be aligned
towards the tank wall.
A B
°
°
90
90
°
90
° °
°
90 90
90
90 90
° °
90 90
° °
A0018974
Nozzle mounting
H
øD 1
A0016819
å 15 Nozzle height an diameter for horn antenna, flush mount (FMR52)

1 Spring washers
Antenna size 50 mm (2 in) 80 mm (3 in)
D 44 mm (1.73 in) 75 mm (2.95 in)
H < 500 mm (19.7 in) < 500 mm (19.7 in)
Please contact Endress+Hauser for applications with higher nozzle.
For flanges with PTFE cladding: Use spring washers (see figure) to compensate for the sagging of the
cladding.
It is recommended to tighten the the flange bolts periodically, depending on process temperature and
pressure.
Recommended torque: 60 to 100 Nm (44.25 to 73.75 lbf ft)
Endress+Hauser 43
Installation in stilling well
°
90
1
A0016841
å 16 Installation in stilling well

1 Marking for antenna alignment
• For horn antenna: Align the marking towards the slots of the stilling well.
• Measurements can be performed through an open full bore ball valve without any problems.
• After mounting, the housing can be turned 350° in order to simplify access to the display and the terminal
compartment.
44 Endress+Hauser
Recommendations for the stilling well

• Metal (no enamel coating; plastic on request).
• Constant diameter.
• Diameter of stilling well not larger than antenna diameter.
• Weld seam as smooth as possible and on the same axis as the slots.
• Slots offset 180° (not 90°).
• Slot width or diameter of holes max. 1/10 of pipe diameter, de-burred. Length and number do not have
any influence on the measurement.
• Select horn antenna as big as possible. For intermedaite sizes (e.g. 180 mm (7 in)) select next larger
antenna and adapt it mechanically (for horn antennas)
• At any transition (i.e. when using a ball valve or mending pipe segments), no gap may be created
exceeding 1 mm (0.04 in).
• The stilling well must be smooth on the inside (average roughness Rz ≤ 6.3 mm (248 min)). Use extruded
or parallel welded stainless steel pipe. An extension of the pipe is possible with welded flanges or pipe
sleeves. Flange and pipe have to be properly aligned at the inside.
• Do not weld through the pipe wall. The inside of the stilling well must remain smooth. In case of
unintentional welding through the pipe, the weld seam and any unevenness on the inside need to be
carefully removed and smoothened. Otherwise, strong interference echoes will be generated and material
build-up will be promoted.
• Particularly on smaller nominal widths it needs to be observed that flanges are welded to the pipe such
that they allow for a correct orientation (marker aligned toward slots).
The performance of Micropilot FMR54 with planar antenna is not dependent on the alignment or
geometry of standard stilling wells. No special alignment is required. However, make sure that the
planar antenna is installed vertically relative to the stilling well axis.
Endress+Hauser 45
Examples for the construction of stilling wells
A B A-A
A A 1
1 C
2 3
100%
100%
4
5
(5.91...19.7)
150…500
≤ 1 (0.04)
(5.91...19.7)
150…500
≤ 1 (0.04)
D 6
0%
0%
mm (in)
A0019009
A Micropilot FMR50/FMR51: Horn 40mm(1½")

B Micropilot FMR50/FMR51/FMR52/FMR54: Horn 80mm(3")
C Stilling well with slots
D Full bore ball valve
1 Marking for axial alignment
2 Threaded connection
3 e.g. welding neck flange DIN2633
4 Æ hole max. 1/10 Æ stilling well
5 Æ hole max. 1/10 Æ stilling well; single sided or drilled through
6 Inside of holes deburred
7 Diameter of opening of ball valve must always be equivalent to pipe diameter; avoid edges and constrictions.
46 Endress+Hauser
Installation in bypass
°
90
1
°
90
A0019446
å 17 Installation in bypass
1 Marking for antenna alignment
2 Tank connectors
• Alighn the marker perpendicular (90°) to the tank connectors.

• Measurements can be performed through an open full bore ball valve without any problems.
• After mounting, the housing can be turned 350° in order to simplify access to the display and the terminal
compartment.
Endress+Hauser 47
Recommendations for the bypass pipe

• Metal (no plastic or enamel coating).
• Constant diameter.
• Select horn antenna as big as possible. For intermediate sizes (e.g. 95 mm (3.5 in)) select next larger
antenna and adapt it mechanically (for horn antennas).
• At any transition (i.e. when using a ball valve or mending pipe segments), no gap may be created
exceeding 1 mm (0.04 in).
• In the area of the tank connections (~ ±20 cm (7.87 in)) ia reduced accuracy of the measurement has to
be expected.
48 Endress+Hauser
Example for the construction of a bypass
A
A-A
A A
≤ 1 (0.04)
2
C
(7.87) (7.87)
100% 200 200
3
4 B
4
3
(7.87) (7.87)
200
0%
200
mm (in)
A0019010
A Micropilot FMR50/FMR51/FMR52/FMR54: Horn 80mm(3")

B Full bore ball valve
C Minimum distance to upper connection pipe: 400 mm (15,7 in)
1 Marking for axial alignment
2 e.g. welding neck flange DIN2633
3 Diameter of the connection pipes as small as possible
4 Do not weld through the pipe wall; the inside of the bypass must remain smooth.
5 Diameter of opening of ball valve must always be equivalent to pipe diameter. Avoid edges and constrictions.
Endress+Hauser 49
Vessels with heat insulation
1
2
A0019142
If process temperatures are high, the device must be included in normal tank insulation to prevent the
electronics heating up as a result of heat radiation or convection. The insulation may not exceed beyond the
neck of the housing.
50 Endress+Hauser
Environment
Ambient temperature range Measuring device –40 to +80 °C (–40 to +176 °F); –50 °C (–58 °F) with manufacturer declaration on
request
Local display –20 to +70 °C (–4 to +158 °F), the readability of the display may be impaired at
temperatures outside the temperature range.
When operating the device in the open with strong sunlight:

• Mount the device in a shady position.
• Avoid direct sunlight, especially in warmer regions.
• Use a weather protection cover (see accessories).
Ambient temperature limits The following diagrams take into account only function requirements. There may be further restrictions
for certified device versions. Please refere to the separate Safety Instructions (® ä 87).
With a temperature (Tp) at the process connection the admissible ambient temperature (Ta) is reduced
according to the following diagram (temperature derating):
Information concerning the derating tables

Option Meaning
A 2-wire; 4-20 mA HART
B 2-wire; 4-20 mA HART, switch output
C 2-wire; 4-20 mA HART, 4-20 mA
E 2-wire; FF, switch output
G 2-wire; PA, switch output
K 4-wire 90-253VAC; 4-20 mA HART
L 4-wire 10, 4-48VDC; 4-20 mA HART
FMR51 Ta
P1 P2
Seal:
• Viton GLT, –40 to 150 °C (–40 to 302 °F) P3
• Kalrez, –20 to 150 °C (–4 to 302 °F)
Housing: GT18 (316 L) Tp
Temperature unit: °C (°F) P5 P4
A0019351
Power Supply; Output (Pos. 2 of P1 P2 P3 P4 P5 P6

the product structure)
Tp Ta Tp Ta Tp Ta Tp Ta Tp Ta Tp Ta
A -40 81 81 81 150 66 150 -40 -40 -40 - -

(-40) (178) (178) (178) (302) (151) (302) (-40) (-40) (-40)
B -40 82 82 82 150 67 150 -40 -40 -40 - -

Switch output not used (-40) (180) (180) (180) (302) (153) (302) (-40) (-40) (-40)
B -40 77 77 77 150 61 150 -40 -40 -40 - -

Switch output used (-40) (171) (171) (171) (302) (142) (302) (-40) (-40) (-40)
C -40 82 82 82 150 67 150 -40 -40 -40 - -

Channel 2 not used (-40) (180) (180) (180) (302) (153) (302) (-40) (-40) (-40)
C -40 79 79 79 150 63 150 -40 -40 -40 - -

Channel 2 used (-40) (174) (174) (174) (302) (145) (302) (-40) (-40) (-40)
E, G -40 83 83 83 150 68 150 -40 -40 -40 - -

E, G -40 78 78 78 150 63 150 -40 -40 -40 - -

K, L -40 77 77 77 150 62 150 -40 -40 -40 - -

(-40) (171) (171) (171) (302) (144) (302) (-40) (-40) (-40)
Endress+Hauser 51
FMR51 Ta
P1 P2
Seal:
• Kalrez, –20 to 150 °C (–4 to 302 °F)
Housing: GT19 (Plastics PBT) Tp
A0019351

A -40 80 80 80 150 56 150 -40 -40 -40 - -

(-40) (176) (176) (176) (302) (133) (302) (-40) (-40) (-40)
B -40 76 76 76 150 56 150 -40 -40 -40 - -

B -40 60 60 60 150 38 150 -40 -40 -40 - -

C -40 82 82 82 150 56 150 -40 -40 -40 - -

Channel 2 not used (-40) (180) (180) (180) (302) (133) (302) (-40) (-40) (-40)
C -40 74 74 74 150 55 150 -40 -40 -40 - -

Channel 2 used (-40) (165) (165) (165) (302) (131) (302) (-40) (-40) (-40)
E, G -40 79 79 79 150 56 150 -40 -40 -40 - -

E, G -40 63 63 63 150 41 150 -40 -40 -40 - -

FMR51 Ta
P1 P2
Seal:
• Kalrez, –20 to 150 °C (–4 to 302 °F)
Housing: GT20 (Alu, coated) Tp
A0019351

A -40 81 81 81 150 69 150 -40 -40 -40 - -

(-40) (178) (178) (178) (302) (156) (302) (-40) (-40) (-40)
B -40 82 82 82 150 70 150 -40 -40 -40 - -

B -40 77 77 77 150 64 150 -40 -40 -40 - -

C -40 82 82 82 150 70 150 -40 -40 -40 - -

Channel 2 not used (-40) (180) (180) (180) (302) (158) (302) (-40) (-40) (-40)
C -40 79 79 79 150 66 150 -40 -40 -40 - -

Channel 2 used (-40) (174) (174) (174) (302) (151) (302) (-40) (-40) (-40)
E, G -40 83 83 83 150 71 150 -40 -40 -40 - -

E, G -40 78 78 78 150 65 150 -40 -40 -40 - -

K, L -40 77 77 77 150 65 150 -40 -40 -40 - -

(-40) (171) (171) (171) (302) (149) (302) (-40) (-40) (-40)
52 Endress+Hauser
FMR51 Ta
Seal: Graphite, –40 to 250 °C (–40 to 482 °F) P1 P2
Housing: GT18 (316 L) P3
Temperature unit: °C (°F)
Tp
P5 P4
A0019351

A -40 81 81 81 250 63 250 -40 -40 -40 - -

(-40) (178) (178) (178) (482) (145) (482) (-40) (-40) (-40)
B -40 82 82 82 250 64 250 -40 -40 -40 - -

B -40 77 77 77 250 58 250 -40 -40 -40 - -

C -40 82 82 82 250 64 250 -40 -40 -40 - -

Channel 2 not used (-40) (180) (180) (180) (482) (147) (482) (-40) (-40) (-40)
C -40 79 79 79 250 61 250 -40 -40 -40 - -

Channel 2 used (-40) (174) (174) (174) (482) (142) (482) (-40) (-40) (-40)
E, G -40 83 83 83 250 65 250 -40 -40 -40 - -

E, G -40 78 78 78 250 60 250 -40 -40 -40 - -

K, L -40 77 77 77 250 59 250 -40 -40 -40 - -

(-40) (171) (171) (171) (482) (138) (482) (-40) (-40) (-40)
FMR51 Ta
Housing: GT19 (Plastics PBT) P3
Tp
P5 P4
A0019351

A -40 80 80 80 250 44 250 -40 -40 -40 - -

(-40) (176) (176) (176) (482) (111) (482) (-40) (-40) (-40)
B -40 76 76 76 250 44 250 -40 -40 -40 - -

B -40 60 60 60 250 32 250 -40 -40 -40 - -

C -40 82 82 82 250 44 250 -40 -40 -40 - -

Channel 2 not used (-40) (180) (180) (180) (482) (111) (482) (-40) (-40) (-40)
C -40 74 74 74 250 44 250 -40 -40 -40 - -

Channel 2 used (-40) (165) (165) (165) (482) (111) (482) (-40) (-40) (-40)
E, G -40 79 79 79 250 44 250 -40 -40 -40 - -

E, G -40 63 63 63 250 35 250 -40 -40 -40 - -

Endress+Hauser 53
FMR51 Ta
Housing: GT20 (Alu, coated) P3
Tp
P5 P4
A0019351

A -40 81 81 81 250 67 250 -40 -40 -40 - -

(-40) (178) (178) (178) (482) (153) (482) (-40) (-40) (-40)
B -40 82 82 82 250 68 250 -40 -40 -40 - -

B -40 77 77 77 250 62 250 -40 -40 -40 - -

C -40 82 82 82 250 68 250 -40 -40 -40 - -

Channel 2 not used (-40) (180) (180) (180) (482) (154) (482) (-40) (-40) (-40)
C -40 79 79 79 250 64 250 -40 -40 -40 - -

Channel 2 used (-40) (174) (174) (174) (482) (147) (482) (-40) (-40) (-40)
E, G -40 83 83 83 250 69 250 -40 -40 -40 - -

E, G -40 78 78 78 250 64 250 -40 -40 -40 - -

K, L -40 77 77 77 250 63 250 -40 -40 -40 - -

(-40) (171) (171) (171) (482) (154) (482) (-40) (-40) (-40)
FMR51 Ta
P6 Tp
P5 P4
A0019344

A -196 81 81 81 450 26 450 -40 -40 -40 -196 -15

(-321) (178) (178) (178) (842) (79) (842) (-40) (-40) (-40) (-321) (+5)
B -196 82 82 82 450 26 450 -40 -40 -40 -196 -15

Switch output not used (-321) (180) (180) (180) (842) (79) (842) (-40) (-40) (-40) (-321) (+5)
B -196 77 77 77 450 25 450 -40 -40 -40 -196 -15

Switch output used (-321) (171) (171) (171) (842) (77) (842) (-40) (-40) (-40) (-321) (+5)
C -196 82 82 82 450 26 450 -40 -40 -40 -196 -15

Channel 2 not used (-321) (180) (180) (180) (842) (79) (842) (-40) (-40) (-40) (-321) (+5)
C -196 79 79 79 450 26 450 -40 -40 -40 -196 -15

Channel 2 used (-321) (174) (174) (174) (842) (79) (842) (-40) (-40) (-40) (-321) (+5)
E, G -196 83 83 83 450 26 450 -40 -40 -40 -196 -15

Switch output not used (-321) (181) (181) (181) (842) (79) (842) (-40) (-40) (-40) (-321) (+5)
E, G -196 78 78 78 450 26 450 -40 -40 -40 -196 -15

Switch output used (-321) (172) (172) (172) (842) (79) (842) (-40) (-40) (-40) (-321) (+5)
K, L -196 77 77 77 450 26 450 -40 -40 -40 -196 -15

(-321) (171) (171) (171) (842) (79) (842) (-40) (-40) (-40) (-321) (+5)
54 Endress+Hauser
FMR51 Ta
P6 Tp
P5 P4
A0019344

A -196 80 80 80 450 -29 450 -40 -40 -40 -196 9

(-321) (176) (176) (176) (842) (-20) (842) (-40) (-40) (-40) (-321) (48)
B -196 76 76 76 450 -29 450 -40 -40 -40 -196 9

Switch output not used (-321) (169) (169) (169) (842) (-20) (842) (-40) (-40) (-40) (-321) (48)
B -196 60 60 60 450 -29 450 -40 -40 -40 -196 9

Switch output used (-321) (140) (140) (140) (842) (-20) (842) (-40) (-40) (-40) (-321) (48)
C -196 82 82 82 450 -29 450 -40 -40 -40 -196 9

Channel 2 not used (-321) (180) (180) (180) (842) (-20) (842) (-40) (-40) (-40) (-321) (48)
C -196 74 74 74 450 -29 450 -40 -40 -40 -196 9

Channel 2 used (-321) (165) (165) (165) (842) (-20) (842) (-40) (-40) (-40) (-321) (48)
E, G -196 79 79 79 450 -29 450 -40 -40 -40 -196 9

Switch output not used (-321) (174) (174) (174) (842) (-20) (842) (-40) (-40) (-40) (-321) (48)
E, G -196 63 63 63 450 -29 450 -40 -40 -40 -196 9

Switch output used (-321) (145) (145) (145) (842) (-20) (842) (-40) (-40) (-40) (-321) (48)
FMR51 Ta
P6 Tp
P5 P4
A0019344

A -196 81 81 81 450 39 450 -40 -40 -40 -196 -20

(-321) (178) (178) (178) (842) (102) (842) (-40) (-40) (-40) (-321) (-4)
B -196 82 82 82 450 39 450 -40 -40 -40 -196 -20

Switch output not used (-321) (180) (180) (180) (842) (102) (842) (-40) (-40) (-40) (-321) (-4)
B -196 77 77 77 450 36 450 -40 -40 -40 -196 -20

Switch output used (-321) (171) (171) (171) (842) (97) (842) (-40) (-40) (-40) (-321) (-4)
C -196 82 82 82 450 39 450 -40 -40 -40 -196 -20

Channel 2 not used (-321) (180) (180) (180) (842) (102) (842) (-40) (-40) (-40) (-321) (-4)
C -196 79 79 79 450 38 450 -40 -40 -40 -196 -20

Channel 2 used (-321) (174) (174) (174) (842) (100) (842) (-40) (-40) (-40) (-321) (-4)
E, G -196 83 83 83 450 39 450 -40 -40 -40 -196 -20

Switch output not used (-321) (181) (181) (181) (842) (102) (842) (-40) (-40) (-40) (-321) (-4)
E, G -196 78 78 78 450 38 450 -40 -40 -40 -196 -20

Switch output used (-321) (172) (172) (172) (842) (100) (842) (-40) (-40) (-40) (-321) (-4)
K, L -196 77 77 77 450 37 450 -40 -40 -40 -196 -20

(-321) (171 (171) (171) (842) (99) (842) (-40) (-40) (-40) (-321) (-4)
Endress+Hauser 55
FMR52 Ta
Antenna: Horn 50mm/2" P1 P2
Tp
P5 P4
A0019351

A -40 81 81 81 200 61 200 -40 -40 -40 - -

(-40) (178) (178) (178) (392) (142) (392) (-40) (-40) (-40)
B -40 82 82 82 200 61 200 -40 -40 -40 - -

B -40 77 77 77 200 55 200 -40 -40 -40 - -

C -40 82 82 82 200 62 200 -40 -40 -40 - -

Channel 2 not used (-40) (180) (180) (180) (392) (144) (392) (-40) (-40) (-40)
C -40 79 79 79 200 58 200 -40 -40 -40 - -

Channel 2 used (-40) (174) (174) (174) (392) (136) (392) (-40) (-40) (-40)
E, G -40 83 83 83 200 62 200 -40 -40 -40 - -

E, G -40 78 78 78 200 57 200 -40 -40 -40 - -

K, L -40 77 77 77 200 56 200 -40 -40 -40 - -

(-40) (171) (171) (171) (392) (133) (392) (-40) (-40) (-40)
FMR52 Ta
Tp
P5 P4
A0019351

A -40 80 80 80 200 42 200 -40 -40 -40 - -

(-40) (176) (176) (176) (392) (108) (392) (-40) (-40) (-40)
B -40 76 76 76 200 42 200 -40 -40 -40 - -

B -40 60 60 60 200 31 200 -40 -40 -40 - -

C -40 82 82 82 200 42 200 -40 -40 -40 - -

Channel 2 not used (-40) (180) (180) (180) (392) (108) (392) (-40) (-40) (-40)
C -40 74 74 74 200 42 200 -40 -40 -40 - -

Channel 2 used (-40) (165) (165) (165) (392) (108) (392) (-40) (-40) (-40)
E, G -40 79 79 79 200 42 200 -40 -40 -40 - -

E, G -40 63 63 63 200 33 200 -40 -40 -40 - -

56 Endress+Hauser
FMR52 Ta
Tp
P5 P4
A0019351

A -40 81 81 81 200 65 200 -40 -40 -40 - -

(-40) (178) (178) (178) (392) (149) (392) (-40) (-40) (-40)
B -40 82 82 82 200 65 200 -40 -40 -40 - -

Switch output not used (-40) (180) (180) (180) (392) (149 (392) (-40) (-40) (-40)
B -40 77 77 77 200 59 200 -40 -40 -40 - -

C -40 82 82 82 200 66 200 -40 -40 -40 - -

Channel 2 not used (-40) (180) (180) (180) (392) (151) (392) (-40) (-40) (-40)
C -40 79 79 79 200 62 200 -40 -40 -40 - -

Channel 2 used (-40) (174) (174) (174) (392) (144) (392) (-40) (-40) (-40)
E, G -40 83 83 83 200 66 200 -40 -40 -40 - -

E, G -40 78 78 78 200 61 200 -40 -40 -40 - -

K, L -40 77 77 77 200 60 200 -40 -40 -40 - -

(-40) (171) (171) (171) (392) (140) (392) (-40) (-40) (-40)
FMR52 Ta
Tp
P5 P4
A0019351

A -40 81 81 81 200 57 200 -40 -40 -40 - -

(-40) (178) (178) (178) (392) (135) (392) (-40) (-40) (-40)
B -40 82 82 82 200 57 200 -40 -40 -40 - -

B -40 77 77 77 200 51 200 -40 -40 -40 - -

C -40 82 82 82 200 57 200 -40 -40 -40 - -

Channel 2 not used (-40) (180) (180) (180) (392) (135) (392) (-40) (-40) (-40)
C -40 79 79 79 200 54 200 -40 -40 -40 - -

Channel 2 used (-40) (174) (174) (174) (392) (129) (392) (-40) (-40) (-40)
E, G -40 83 83 83 200 57 200 -40 -40 -40 - -

E, G -40 78 78 78 200 53 200 -40 -40 -40 - -

K, L -40 77 77 77 200 52 200 -40 -40 -40 - -

(-40) (171) (171) (171) (392) (126) (392) (-40) (-40) (-40)
Endress+Hauser 57
FMR52 Ta
Tp
P5 P4
A0019351

A -40 80 80 80 200 36 200 -40 -40 -40 - -

(-40) (176) (176) (176) (392) (97) (392) (-40) (-40) (-40)
B -40 76 76 76 200 36 200 -40 -40 -40 - -

B -40 60 60 60 200 27 200 -40 -40 -40 - -

C -40 82 82 82 200 36 200 -40 -40 -40 - -

Channel 2 not used (-40) (180) (180) (180) (392) (97) (392) (-40) (-40) (-40)
C -40 74 74 74 200 36 200 -40 -40 -40 - -

Channel 2 used (-40) (165) (165) (165) (392) (97) (392) (-40) (-40) (-40)
E, G -40 79 79 79 200 36 200 -40 -40 -40 - -

E, G -40 63 63 63 200 30 200 -40 -40 -40 - -

FMR52 Ta
Tp
P5 P4
A0019351

A -40 81 81 81 200 61 200 -40 -40 -40 - -

(-40) (178) (178) (178) (392) (142) (392) (-40) (-40) (-40)
B -40 82 82 82 200 62 200 -40 -40 -40 - -

B -40 77 77 77 200 56 200 -40 -40 -40 - -

C -40 82 82 82 200 62 200 -40 -40 -40 - -

Channel 2 not used (-40) (180) (180) (180) (392) (144) (392) (-40) (-40) (-40)
C -40 79 79 79 200 58 200 -40 -40 -40 - -

Channel 2 used (-40) (174) (174) (174) (392) (136) (392) (-40) (-40) (-40)
E, G -40 83 83 83 200 62 200 -40 -40 -40 - -

E, G -40 78 78 78 200 58 200 -40 -40 -40 - -

K, L -40 77 77 77 200 57 200 -40 -40 -40 - -

(-40) (171) (171) (171) (392) (135) (392) (-40) (-40) (-40)
Storage temperature –40 to +80 °C (–40 to +176 °F)
Climate class DIN EN 60068-2-38 (test Z/AD)
58 Endress+Hauser
Geometric height according Up to 2 000 m (6 600 ft) above MSL.

to IEC61010-1 Ed.3
Can be expanded to 3 000 m (9 800 ft) above MSL by application of an overvoltage protection, e.g. HAW562
or HAW569.
Degree of protection • With closed housing tested according to:

– IP68, NEMA6P (24 h at 1.83 m under water surface)
– For plastic housing with transparent cover (display module): IP68 (24 h at 1.00 m under water
surface) 6)
– IP66, NEMA4X
• With open housing: IP20, NEMA1 (also ingress protection of the display)
Degree of protection IP68 NEMA6P applies for M12 PROFIBUS PA plugs only when the PROFIBUS
cable is plugged in and is also rated IP68 NEMA6P.
Vibration resistance DIN EN 60068-2-64 / IEC 68-2-64: 20 to 2 000 Hz, 1 (m/s2)2/Hz
Cleaning the antenna The antenna can get contaminated, depending on the application. The emission and reception of microwaves
can thus eventually be hindered. The degree of contamination leading to an error depends on the medium
and the reflectivity, mainly determined by the dielectric constant er.
If the medium tends to cause contamination and deposits, cleaning on a regular basis is recommended. Care
has to be taken not to damage the antenna in the process of a mechanical or hose-down cleaning. The
material compatibility has to be considered if cleaning agents are used! The maximum permitted
temperature at the flange should not be exceeded.
Electromagnetic compatibility Electromagnetic compatibility to all relevant requirements of the EN 61326- series and NAMUR
(EMC) recommendation EMC (NE21). For details see declaration of conformity. 7).
If only the analogue signal is used, unshielded interconnection lines are sufficient for the installation. In case
of using the digital signal (HART/ PA/ FF) use shielded interconnection lines. Use a shielded cable when
working with a digital communications signal.
Max. fluctuations during EMC- tests: < 0.5 % of the span. As an exception to this, the maximum
fluctuations may amount to 2 % of the span for devices with plastic housing and see-through lid (integrated
display and operating module SD02 or SD03) if strong electromagnetic interferences in the frequenency
range of 1 to 2 GHz are present.
6) This restriction is valid if the following options of the product structure have been selected at the same time: 030("Display, Operation") = C("SD02") or
E("SD03"); 040("Housing") = A("GT19").
7) Can be downloaded from www.endress.com.
Endress+Hauser 59
Process
Process temperature range Sensor Seal 1) Process temperature range
FMR51 Viton GLT –40 to +150 °C (–40 to 302 °F)
Kalrez –20 to +150 °C (–4 to 302 °F)
Graphite, -40 ... 250°C / -40 ... 482°F –40 to +250 °C (–40 to 482 °F)
Graphite, -196...450°C / -321...842°F –196 to +450 °C (–321 to 842 °F)
FMR52 - –40 to +200 °C (–40 to 392 °F)
Process pressure range Sensor Process pressure range
FMR51 prel = –1 to 40 bar (–14.5 to 580 psi)
FMR52 prel = –1 to 25 bar (–14.5 to 363 psi)
This range may be reduced by the selected process connection. The pressure rating (PN) specified on
the flanges refers to a reference temperature of 20 °C, for ASME flanges 100 °F. Pay attention to
pressure-temperature dependencies.
Please refer to the following standards for the pressure values permitted for higher temperatures:
• EN 1092-1: 2001 Tab. 18
With regard to their temperature stability properties, the materials 1.4435 and 1.4404 are grouped
under 13E0 in EN 1092-1 Tab. 18. The chemical composition of the two materials can be identical.
• ASME B 16.5a - 1998 Tab. 2-2.2 F316
• ASME B 16.5a - 1998 Tab. 2.3.8 N10276
• JIS B 2220
Dielectric constant • For liquids

– er ³ 1.9 in free-field applications
– er ³ 1.4 in stilling well
• For bulk solids
er ³ 1.6
60 Endress+Hauser
Mechanical construction
Dimensions Dimensions of the electronics housing
R100 98 (3.86)*
78 (3.07) 90 (3.54)
)
.07
(ø4
3.5
141.9 (5.59)
ø108.5 (ø4.27)
ø10
144 (5.67)
115.25 (4.54)
A0011666
å 18 Housing GT18 (316L); Dimensions in mm (in)

*This measure is valid for devices with integrated overvoltage protection.
R100
99.5 (3.92)*
78 (3.07) 90 (3.54)
7)
4.1
6 (ø
ø10
163 (6.42)
ø106 (ø4.17)
134.5 (5.3)
A0011346
å 19 Housing GT19 (Plastics PBT); Dimensions in mm (in)

R100
97 (3.82)*
78 (3.07) 90 (3.54)
7)
0
ø4.
(
3.5
ø111 (ø4.37) - 1°
141.5 (5.57)
ø10
144 (5.67)
ø108.5 (ø4.27)
117.1 (4.61)
A0011665
å 20 Housing GT20 (Alu coated); Dimensions in mm (in)

Endress+Hauser 61
Dimensions FMR51 (process connection/antenna)
A B C D
55 55
(2.66)
(2.66)
67.5
67.5
(2.48)
63
R
100(3.94)
b
26 (1.02)
26 (1.02)
5 (0.2)
5 (0.2)
L
5 (0.2)
ød ød
øD
L
øA
ød mm (in)
A0017753
A Threaded connection
B Clamp adapter 2"/3"
C Flange version
D Threaded connection with antenna extension 100 mm (3.94 in)
R Reference point of the measurement
A B C D
121.4 (4.78)
115.4 (4.54)
55
(2.48)
63
R
26 (1.02)
100(3.94)
b
L
ød ød
5 (0.2)
øD
L
ød mm (in)
øD
øA
A0017755
A Clamp adapter 2"/3" with antenna extension 100 mm (3.94 in)

B Flange version with antenna extension 100 mm (3.94 in)
C Version XT 250°C (482 °F) with threaded connection
D Version XT 250°C (482 °F) with flange
62 Endress+Hauser
(2.56)
65
R
b
3 (0.12)
L
ød
øD
140.1 (5.52)
B C
(2.48) 55
(2.66)
67.5
b
63
R
(2.09...17.8) (1.85)
47
26 (1.02)
b
L
53...453
ø27 (1.06)
ød
øD
L2
ød
øD mm (in)
A0017756
A Flange version, coated

B Version flange with antenna extension > 100 mm (3.94 in) to 500 mm (19.7 in)
C Version threaded connection with antenna extension > 100 mm (3.94 in) to 500 mm (19.7 in)
D Version HT 450 °C (842 °F) with flange
Horn antenna
Dimension 40 mm (1") 50 mm (2") 80 mm (3") 100 mm (4")
L 86 mm (3.39 in) 115 mm (4.53 in) 211 mm (8.31 in) 282 mm (11.1 in)
⌀d ⌀40 mm (1.57 in) ⌀48 mm (1.89 in) ⌀75 mm (2.95 in) ⌀95 mm (3.74 in)
L2 51 mm (2.01 in) 80 mm (3.15 in) 176 mm (6.93 in) 247 mm (9.72 in)
Flanges according to EN1092-1 (suitable for DIN2527)

Dimension Version DN50 DN80 DN100 DN150
b 18 mm (0.71 in) 20 mm (0.79 in) 20 mm (0.79 in) 22 mm (0.87 in)

PN16
⌀D ⌀165 mm (6.5 in) ⌀200 mm (7.87 in) ⌀220 mm (8.66 in) ⌀285 mm (11.2 in)
b 20 mm (0.79 in) 24 mm (0.94 in) 24 mm (0.94 in) -

PN40
⌀D ⌀165 mm (6.5 in) ⌀200 mm (7.87 in) ⌀235 mm (9.25 in) -
b - - 30 mm (1.18 in) -
PN63
⌀D - - ⌀250 mm (9.84 in) -
Endress+Hauser 63
b - - 36 mm (1.42 in) -
PN100
⌀D - - ⌀265 mm (10.4 in) -
Flanges according to JIS B2220


10 K
⌀D ⌀155 mm (6.1 in) ⌀185 mm (7.28 in) ⌀210 mm (8.27 in) ⌀280 mm (11 in)
b - - 44 mm (1.73 in) -
63 K
⌀D - - ⌀270 mm (10.6 in) -
Flanges according to ANSI B16.5

Dimension Version 2" 3" 4" 6"
b 19.1 mm (0.75 in) 23.9 mm (0.94 in) 23.9 mm (0.94 in) 25.4 mm (1 in)
150 lbs
⌀D ⌀152.4 mm (6 in) ⌀190.5 mm (7.5 in) ⌀228.6 mm (9 in) ⌀279.4 mm (11 in)
300 lbs
⌀D ⌀165.1 mm (6.5 in) ⌀209.5 mm (8.25 in) ⌀254 mm (10 in) ⌀279.4 mm (11 in)
Tri-Clamp according to ISO 2852

Dimension 2" 3"
A 64 mm (2.52 in) 91 mm (3.58 in)
64 Endress+Hauser
Dimensions FMR52 (process connection/antenna)
A B C
92.6(3.65)
2.6 (0.1)
95 (3.74)
4 (0.16)
94(3.7)
5 (0.2)
b
R
ø48 (1.89) ø48 ø48 (1.89)
(0.54)
(0.54)
(0.54)
13.8
13.8
13.8
øa (1.89) øb øc
ød
D E F
119.6 (4.71)
121(4.76)
123 (4.84)
2.6 (0.1)
4 (0.16)
5 (0.2)
b
R
ø75 (2.95) ø75 ø75 (2.95)
28.6 (1.13)
28.6 (1.13)
28.6 (1.13)
øa (2.95) øb øc
ød
mm (in)
A0017748
A Dairy coupling adapter DN50

B Clamp adapter DN50
C Version DN50 with flange
D Dairy coupling adapter DN80
E Clamp adapter DN80
F Version DN80 with flange
Dairy coupling according to DIN 11851

Dimension DN50 DN80
⌀a ⌀68.5 mm (2.7 in) ⌀100 mm (3.94 in)
Tri-Clamp according to ISO 2852

Dimension 2" 3" 4"
⌀b ⌀64 mm (2.52 in) ⌀91 mm (3.58 in) ⌀119 mm (4.69 in)
Flanges according to EN1092-1 (suitable for DIN2527)

⌀c PN16 ⌀102 mm (4.02 in) ⌀138 mm (5.43 in) ⌀158 mm (6.22 in) ⌀212 mm (8.35 in)
Endress+Hauser 65
Flanges according to ANSI B16.5

Dimension Version 2" 3" 4" 6"
⌀c 150 lbs ⌀92 mm (3.62 in) ⌀127 mm (5 in) ⌀158 mm (6.22 in) ⌀212 mm (8.35 in)
⌀d ⌀152.4 mm (6 in) ⌀190.5 mm (7.5 in) ⌀228.6 mm (9 in) ⌀279.4 mm (11 in)
Flanges according to JIS B2220

⌀c 10 K ⌀96 mm (3.78 in) ⌀127 mm (5 in) ⌀151 mm (5.94 in) ⌀212 mm (8.35 in)
⌀d ⌀155 mm (6.1 in) ⌀185 mm (7.28 in) ⌀210 mm (8.27 in) ⌀280 mm (11 in)
Weight Housing
Part Weight
Housing GT18 - stainless steel approx. 4.5 kg (9.9 lbs)
Housing GT19 - plastic approx. 1.2 kg (2.7 lbs)
Housing GT20 - aluminium approx. 1.9 kg (4.2 lbs)
Antenna and process connection

Device Weight of antenna and process connection
FMR51 max. 3.0 kg (6.6 lbs) + weight of flange 1)
FMR52 max. 4 kg (8.8 lbs) + weight of flange 1)
1) For the weight of the flange refer to Technical Information TI00426F.
Materials Housing
2.1 1 2.2 5
4 3 9 8 7 6
A0013788
Housing GT18 - stainless steel, corrosion-resistant
No. Part: material No. Part: material
1 Housing: 316L (CF-3M, 1.4404) 5 Cable entry

• Sealing: EMPB
2.1 Cover of the electronics compartment • Cable gland: 316L (1.4404)
• Cover: 316L (CF-3M, 1.4404) • Adapter: 316L (1.4435)
• Window: glass
• Cover seal: EPDM
66 Endress+Hauser
Housing GT18 - stainless steel, corrosion-resistant
2.2 Cover of the terminal compartment 6 Dummy plug: 316L (1.4404)

• Cover: 316L (CF-3M, 1.4404)
• Cover seal: EPDM 7 Pressure relief stopper: 316L (1.4404)
3 Cover lock 8 Ground terminal

• Screw: A4 • Screw: A4
• Clamp: 316L (1.4404) • Spring washer: A4
• Clamp: 316L (1.4404)
• Holder: 316L (1.4404)
4 Turn housing 9 Identification

• Screw: A4-70 • Nameplate: 304 (1.4301)
• Clamp: 316L (1.4404) • Groove pin: A2
Housing GT19 - plastic
1 Housing: PBT 5 Cable entry

• Sealing: EMPB
2.1 Cover of the electronics compartment • Cable gland: polyamide (PA), nickel-plated brass (CuZn)
• Cover: • Adapter: 316L (1.4435)
– PA (see-through cover)
– PBT (non-transparent cover)
2.2 Cover of the terminal compartment 6 Dummy plug: nickel-plated brass (CuZn)
• Cover: PBT
• Cover seal: EPDM 7 Pressure relief stopper: nickel-plated brass (CuZn)
4 Turn housing 8 Ground terminal

• Screw: A4-70 • Screw: A2
• Clamp: 304 (1.4301)
• Holder: 304 (1.4301)
9 Identification
Nameplate: sticker
Housing GT20 - die-cast aluminum, powder-coated, seawater-resistant
1 Housing: AlSi10Mg(<0.1% Cu) 5 Cable entry

Coating: polyester • Sealing: EMPB
• Cable gland: polyamide (PA), nickel-plated brass (CuZn)
2.1 Cover of the electronics compartment • Adapter: 316L (1.4435)
• Cover: AlSi10Mg(<0.1% Cu)
• Window: glass
2.2 Cover of the terminal compartment 6 Dummy plug: nickel-plated brass (CuZn)
• Cover: AlSi10Mg(<0.1% Cu)
• Cover seal: EPDM 7 Pressure relief stopper: nickel-plated brass (CuZn)
3 Cover lock 8 Ground terminal

• Screw: A4 • Screw: A2
• Clamp: 304 (1.4301)
• Holder: 304 (1.4301)
4 Turn housing 9 Identification

• Screw: A4-70 Nameplate: sticker
• Clamp: 316L (1.4404)
Endress+Hauser 67
Antenna and process connection
FMR51
A B C D
7 7
1 7
3 3
2 2 2
E F G H
3 6 6 3
A0018961
A Version with screw-in adapter

B XT version with threaded connection
C XT version with flange
D HT version with flange
E Version with flange and antenna extension > 100 mm (3.94 in) to 500 mm (19.7 in)
F Version with threaded connection and antenna extension > 100 mm (3.94 in) to 500 mm (19.7 in)
G Version with clamp adapter and antenna extension 100 mm (3.94 in)
H Version with flange and antenna extension 100 mm (3.94 in)
Pos. Part Material
1 Process adapter 316L (1.4404)
Locking washer
2 Horn 316L (1.4404) Hastelloy C22
Screws A4 Hastelloy C22
Spring-lock washer (compact version) A4
Nordlock washer A4
(extension >100 mm, XT und HT
version)
Process separation cone Standard: XT: HT:

PTFE PEEK Al2O3
Seal Standard: XT: HT:

FKM/FFKM Graphite Graphite
3 Flange 316L (1.4404/1.4435) optionally Hastelloy C22 clad
4 Tube extension + adapter 316L (1.4404)
68 Endress+Hauser
Pos. Part Material
5 Extension process adapter 316L (1.4404)
Locking washer
6 Process adapter 316L (1.4404)
7 Housing adapter 316L (1.4404)
Temperature reduction (XT) 316L (1.4404)
Intermediate adapter (HT) 316L (1.4404)
Process adapter 316L (1.4404)
FMR52
A B C
1 1 1
2 2 3
4 4 4
A0018951
A Dairy coupling
B Clamp adapter
C Flange version
Pos. Part Material
1 Adapter 304 (1.4301)
2 Process connection 316L (1.4435)
3 Flange 316L (1.4404/1.4435)
4 Cladding PTFE
(in accordance with FDA 21 CFR 177.1550 and USP <88> Class
VI)
Endress+Hauser 69
Weather protection cover
3.1
3.2
2.1 4
2.2
2.2 5.1
2.1 5.2
4
6
A0015473
Nr. Part: material Nr. Part: material
1 Protection cover: 304 (1.4301) 4 Bracket: 304 (1.4301)
2.1 Washer: A2 5.1 Cheese head screw: A2-70
2.2 Cheese head screw: A4-70 5.2 Nut: A2
3.1 Washer: A2 6 Ground terminal

• Screw: A4
3.2 Tightening screw: 304 (1.4301) • Spring washer: A4
• Clamp: 316L (1.4404)
• Holder: 316L (1.4404)
70 Endress+Hauser
Operability
Operating concept Operator-oriented menu structure for user-specific tasks
• Commissioning
• Operation
• Diagnostics
• Expert level
Quick and safe commissioning
• Guided menus ("Make-it-run" wizards) for applications
• Menu guidance with brief explanations of the individual parameter functions
Reliable operation
• Local operation in different languages (see product structure, feature "Additional Operation Language")
• Standardized operation at the device and in the operating tools
• Data storage device (HistoROM) for process and measuring device data with event logbook available at all
times - even if electronics modules are replaced
Efficient diagnostics increase measurement reliability
• Remedy information is integrated in plain text
• Diverse simulation options and line recorder functions
Local operation Order code for "Display; Operation", option C "SD02" Order code for "Display; Operation", option E "SD03"
(in preparation)
1 1
– –
+ +
E E
A0015544 A0015546
1 Operation with pushbuttons 1 Operation with touch control
Display elements
• 4-line display
• In the case of order code for "Display; Operation", option E: white background lighting; switches to red in
event of device errors (in preparation)
• Format for displaying measured variables and status variables can be individually configured
• Permitted ambient temperature for the display: –20 to +60 °C (–4 to +140 °F)
The readability of the display may be impaired at temperatures outside the temperature range.
Operating elements
• In the case of order code "Display; Operation", Option C: local operation with 3 push buttons ( , , ) E
• In the case of order code for "Display; Operation", option E: external operation via touch control; 3 optical
keys: , , (in preparation)
E
• Operating elements also accessible in various hazardous areas

Additional functionality
• Data backup function
The device configuration can be saved in the display module.
• Data comparison function
The device configuration saved in the display module can be compared to the current device
configuration.
• Data transfer function
The transmitter configuration can be transmitted to another device using the display module.
Endress+Hauser 71
Operation with remote

display and operating module
FHX50
1 2 3
A0013137
å 21 FHX50 operating options

1 Housing of the remote display and operating module FHX50
2 Display and operating module SD02, push buttons; cover must be removed
3 Display and operating module SD03, optical keys; can be operated through the glass of the cover (in preparation)
Remote operation Via HART protocol
6 8
3
2
1 4 5 7
A0013764
å 22 Options for remote operation via HART protocol

1 PLC (programmable logic controller)
2 Transmitter power supply unit, e.g. RN221N (with communication resistor)
3 Connection for Commubox FXA191, FXA195 and Field Communicator 375, 475
4 Field Communicator 375, 475
5 Computer with operating tool (e.g. FieldCare, AMS Device Manager, SIMATIC PDM)
6 Commubox FXA191 (RS232) or FXA195 (USB)
7 Field Xpert SFX100
8 VIATOR Bluetooth modem with connecting cable
9 Transmitter
72 Endress+Hauser
Via PROFIBUS PA protocol (in preparation)
2 3
PROFIBUS DP
ENDRESS + HAUSER
PROFIBUS PA
T
4 4 4
A0015775
1 Segment coupler
2 Computer with Profiboard/Proficard and operating tool (e.g. FieldCare)
3 PLC (Progrommable Logic Controller)
4 Transmitter
5 Additional functions (valves etc.)
Endress+Hauser 73
Via FOUNDATION Fieldbus (in preparation)
IN
BT
FF-HSE
1
FF-H1 SB 2
PS BT
LD 4
3
BT ENDRESS + HAUSER
– +
%
PS
FF-H1
BT
1
2
A0017188
å 23 FOUNDATION Fieldbus system architecture with associated components

IN Industrial network
FF- High Speed Ethernet
HSE
FF- FOUNDATION Fieldbus-H1
H1
LD Linking Device FF-HSE/FF-H1
PS Bus Power Supply
SB Safety Barrier
BT Bus Terminator
1 FFblue Bluetooth modem
2 Field Xpert SFX100
3 FieldCare
4 NI-FF interface card
74 Endress+Hauser
Via service interface (CDI)
3 –
+
E
2 1
A0014019
1 Service interface (CDI) of the measuring device (= Endress+Hauser Common Data Interface)
2 Commubox FXA291
3 Computer with "FieldCare" operating tool
Endress+Hauser 75
Integration in tank gauging The Endress+Hauser Tank Side Monitor NRF590 provides integrated communications for sites with multiple
system tanks, each with one or more sensors on the tank, such as radar, spot or average temperature, capacitive
probe for water detection and/or pressure sensors. Multiple protocols out of the Tank Side Monitor
guarantee connectivity to nearly any of the existing industry standard tank gauging protocols. Optional
connectivity of analog 4...20 mA sensors, digital I/O and analog output simplify full tank sensor integration.
Use of the proven concept of the intrinsically safe HART bus for all on-tank sensors yields extremely low
wiring costs, while at the same time providing maximum safety, reliability and data availability.
1 2 3
4 5
8 NXA820
16...253 VAC
A0017982
å 24 The complete measuring system consists of:

1 Tankvision workstation
2 Commubox FXA195 (USB) - optional
3 Computer with operating tool (ControlCare) - optional
4 Level measuring device
5 Temperature measuring device
6 Tank Side Monitor NRF590
7 Pressure measuring device
8 Tankvision Tank Scanner NXA820
76 Endress+Hauser
System integration via Vendor Managed Inventory

Fieldgate
By using Fieldgates to interrogate tank or silo levels remotely, suppliers of raw materials can provide their
regular customers with information about the current supplies at any time and, for example, account for
them in their own production planning. For their part, the Fieldgates monitor the configured level limits and,
if required, automatically activate the next supply. The spectrum of options here ranges from a simple
purchasing requisition via e-mail through to fully automatic order administration by coupling XML data into
the planning systems on both sides.
Remote maintenance of measuring equipment

Fieldgates not only transfer the current measured values, they also alert the responsible standby personnel, if
required, via e-mail or SMS. In the event of an alarm or also when performing routine checks, service
technicians can diagnose and configure connected HART devices remotely. All that is required for this is the
corresponding HART operating tool (e.g. FieldCare, ...) for the connected device. Fieldgate passes on the
information transparently, so that all options for the respective operating software are available remotely.
Some on-site service operations can be avoided by using remote diagnosis and remote configuration and all
others can at least be better planned and prepared.
1 1 2
ENDRESS+HAUSER ENDRESS+HAUSER
RN 221N RN 221N
FXN 520
20...45 VDC
-
.
A0011278
å 25 The complete measuring system consists of devices and:

1 Fieldgate FXA520
2 Multidrop Connector FXN520
The number of instruments which can be connected in mutidrop mode can be calculated by the
"FieldNetCalc" program. A description of this program can be found in Technical Information TI 400F
(Multidrop Conncector FXN520). The program is available form your Endress+Hauser sales
organisation or in the internet at: www.de.endress.com/Download (text search = "Fieldnetcalc").
Endress+Hauser 77
Certificates and approvals

CE mark The measuring system meets the legal requirements of the applicable EC guidelines. These are listed in the
corresponding EC Declaration of Conformity together with the standards applied.
Endress+Hauser confirms successful testing of the device by affixing to it the CE mark.
C-Tick symbol The measuring system meets the EMC requirements of the "Australian Communications and Media
Authority (ACMA)".
Ex approval • ATEX
• IEC Ex
• CSA (in Vorbereitung)
• FM (in Vorbereitung)
• NEPSI (in Vorbereitung)
• TIIS (in Vorbereitung)
Additional safety instructions must be observed for applications in hazardous areas. They are contained in
the separate "Safety Instructions" (XA) document, which is included in the scope of delivery. Reference is
made to the XA on the nameplate of the device.
Details on the available certificats as well as the associated XAs can be found in the Associated
documentation chapter in the Safety instructions section: (® ä 87).
Dual seal according to The devices Micropilot FMR5x have been designed according to ANSI/ISA 12.27.01 as dual seal devices,
ANSI/ISA 12.27.01 allowing the user to waive the use and save the cost of installing external secondary process seals in the
conduit as required by the process sealing sections of ANSI/NFPA 70 (NEC) and CSA 22.1 (CEC). These
instruments comply with the North-American installation practice and provide a very safe and cost-saving
installation for pressurized applications with hazardous fluids.
Further information can be found in the control drawings of the relevant devices.
Functional Safety Used for level monitoring (MIN, MAX, range) up to SIL 3 (homogeneous or inhomogeneous redundancy),
independently assessed by TÜV Rhineland as per IEC 61508. Other information see documentation
SD01087F: "Functional Safety Manual".
Sanitary compatibility FMR52 with flange cladding made of PTFE conforms to FDA 21 CFR 177.1550 and USP <88> Class VI
3A and EHEDG approval with Tri-Clamp process connection.
The leak-tight connections can be cleaned with the cleaning methods usually used in this industry
without leaving residues.
The 316L housing (GT18), option B in the order attribute 40, is not suitable for applications which
need a 3A approval.
AD2000 The pressure retaining material 316L (1.4435/1.4404) corresponds to AD2000 - W2/W10.
Pressure Equipment Directive The Micropilot is not subject to the scope of the Pressure Equipment Directive 97/23/EC, as it does not
have a pressure-bearing housing according to article 1, section 2.1.4 of the directive.
Marine certificate (in in preparation

preparation)
Radio standard The devices Micropilot FMR50, FMR51, FMR52, FMR56 and FMR57 are conform with the LPR (Level
EN302729-1/2 Probing Radar) standard EN302729-1/2. The devices are allowed to be used inside or outside of closed bins
or tanks in countries of th EU and the EFTA. Precondition is that the country itself already has implemented
the directive.
At present, the following countries have already implemented the directive:
Belgium, Bulgaria, Germany, Denmark, Estonia, France, Greece, Great Britain, Ireland, Iceland, Italy,
Liechtenstein, Lithuania, Latvia, Malta, Netherland, Norway, Austria, Poland, Romania, Sweden,
Switzerland, Slovakia, Spain, Czech Republic and Cyprus.
All countries not mentioned above are at present in the implementation phase.
78 Endress+Hauser
For the use of the devices outside of closed bins or tanks, the following has to be observed:
1. The installation has to be done by trained personnel.
2. The antenna of the device has to be mounted on a fixed place and vertically to the bottom.
3. The mounting place has to be in a distance of at least 4 km to the mentioned astronomical stations or
an appropriate permission has to be issued by the national authority. If the device is mounted at a
distance of 4 to 40 km from the stations mentioned, the maximum mounting height is restricted to
15 m (49 ft).
Astronomical stations
Country Name of the station Geographical latitude Geographical longitude
Germany Effelsberg 50°31'32" N 06°53'00" E
Finland Metsähovi 60°13'04" N 24°23'37" E
Tuorla 60°24'56" N 24°26'31" E
France Plateau de Bure 44°38'01" N 05°54'26" E
Floirac 44°50'10" N 00°31'37" W
United Kingdom Cambridge 52°09'59" N 00°02'20" E
Damhall 53°09'22" N 02°32'03" W
Jodrell Bank 53°14'10" N 02°18'26" W
Knockin 52°47'24" N 02°59'45" W
Pickmere 53°17'18" N 02°26'38" W
Italy Medicina 44°31'14" N 11°38'49" E
Noto 36°52'34" N 14°59'21" E
Sardinia 39°29'50" N 09°14'40" E
Poland Krakow Fort Skala 50°03'18" N 19°49'36" E
Russia Dmitrov 56°26'00" N 37°27'00" E
Kalyazin 57°13'22" N 37°54'01" E
Pushchino 54°49'00" N 37°40'00" E
Zelenchukskaya 43°49'53" N 41°35'32" E
Sweden Onsala 57°23'45" N 11°55'35" E
Switzerland Bleien 47°20'26" N 08°06'44" E
Spain Yebes 40°31'27" N 03°05'22" W
Robledo 40°25'38" N 04°14'57" W
Hungary Penc 47°47'22" N 19°16'53" E
In general the requirements of EN 302729-1/2 has to be taken in consideration.
Radio standard The devices Micropilot FMR50, FMR51, FMR52, FMR53, FMR54, FMR56 and FMR57 are conform with
EN302372-1/2 the TLPR (Tanks Level Probing Radar) standard EN302372-1/2 and can always be used in closed tanks or
bins. For installation, points a to f in Annex B of EN302372-1 have to be taken into account.
FCC / Industry Canada This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Canada CNR-Gen Section 7.1.3
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the
following two conditions: (1) This device may not interference, and (2) this device must accept any
interference, including interference that may cause undesired operation of the device.
Endress+Hauser 79
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de
licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de
brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d'en compromettre le fonctionnement.
[Any] changes or modifications not expressly approved by the party responsible for compliance could void the
user's authority to operate the equipment.
CRN approval in preparation
Track record FMR5x is the upgrade model of the corresponding FMR2xx series.
Other standards and • EN 60529

guidelines Degrees of protection by housing (IP code)
• EN 61010-1
Protection Measures for Electrical Equipment for Measurement, Control, Regulation and Laboratory
Procedures.
• IEC/EN 61326
"Emission in accordance with Class A requirements". Electromagnetic compatibility (EMC requirements)
• NAMUR NE 21
Electromagnetic compatibility (EMC) of industrial process and laboratory control equipment.
• NAMUR NE 43
Standardization of the signal level for the breakdown information of digital transmitters with analog output
signal.
• NAMUR NE 53
Software of field devices and signal-processing devices with digital electronics
• NAMUR NE 107
Status classification as per NE107
• NAMUR NE 131
Requirements for field devices for standard applications
• IEC61508
Functional safety of electrical/electronic/programmable electronic safety-related systems
80 Endress+Hauser
Ordering information
Ordering information Detailed ordering information is available from the following sources:
• In the Product Configurator on the Endress+Hauser website: www.endress.com ® Select country ®
Instruments ® Select device ® Product page function: Configure this product
• From your Endress+Hauser Sales Center: www.endress.com/worldwide
Product Configurator - the tool for individual product configuration
• Up-to-the-minute configuration data
• Depending on the device: Direct input of measuring point-specific information such as measuring
range or operating language
• Automatic verification of exclusion criteria
• Automatic creation of the order code and its breakdown in PDF or Excel output format
• Ability to order directly in the Endress+Hauser Online Shop
5-point linearity protocol (in The following notes must be taken into account if option F4 ("5 point linearity protocol") has been
preparation) selected in feature 550 ("Calibration").
The five points of the linearity protocol are evenly distributetd across the measuring range (0% to 100%). In
order to define the measuring range, Empty calibration (E) and Full calibration (F) have to be specified 8).
The following restrictions have to be taken into account when defining E and F:
R
A
200 (7.87)
E
F
mm (in)
A0017983
Minimum distance between reference point (R) and Minimum span Maximum value for "empty
100% level calibration"
A ³ Length of antenna + 200 mm (8 in) F ³ 400 mm (16 in) E £ 24 m (79 ft)

Minimum value: 400 mm (16 in)
The linearity is checked under reference conditions.
The selected values of Empty calibration and Full calibration are only used to record the linearity
protocol and are reset to their antenna specific default values thereafter. If values different from the
default are required, they must be ordered as a customized parametrization (® ä 82).
8) If E and F are not specified, antenna dependent default values will be used instead.
Endress+Hauser 81
Customized parametrization If the option IJ "Customized parametrization HART", IK "Customized parametrization PA" or IL "Customized
parametrization FF" has been selected in feature 570 "Service", customer specific presettings can be selected
for the following parameters:
Parameter Communication Selection list / range of

values
Setup ® Distance unit • HART • in

• PA • mm
• FF
Setup ® Empty calibration • HART 0 to 70 m (0 to 230 ft)

• PA
• FF
Setup ® Full calibration • HART 0 to 70 m (0 to 230 ft)

• PA
• FF
Setup ® Adv. Setup ® Current output 1/2 ® Damping HART 0 to 999,9 s
Setup ® Adv. Setup ® Current output 1/2 ® Failure mode HART • Min
• Max
• Last valid value
Expert ® Comm. ® HART config. ® Burst mode HART • Off

• On
82 Endress+Hauser
Accessories
Device-specific
Accessory accessories
Description
222 (8.74)
mm (in)
A0015466
298.5 (11.8) 273.8 (10.8)

255.1 (10) 164 (6.46)
b
55°
35°
65
)
(6.1
°
155
mm (in)
A0015472
a 37.8 mm (1.49 in)

b 54 mm (2.13 in)
The weather protection cover can be ordered together with the device (product structure, feature 620 "Accessory Enclosed",
option PB "Weather Protection Cover").
Alternatively, it can be separately ordered as an accessory; order code 71132889.
Endress+Hauser 83
Accessory Description
Remote display FHX50
A0019128
• Material:
– Plastics PBT
– 316L (in preparation)
• Suitable for the display modules:
– SD02 (push buttons)
– SD03 (touch control) (in preparation)
• Connection cable:
– Cable with M12 plug; supplied with the FHX50; up to 30 m (98 ft)
– Customer supplied standard cable; up to 60 m (196 ft)
• If the remote display is to be used, the Micropilot must be ordered in the version "Prepared for display FHX50" (feature
030, option L or M). For the FHX50, on the other hand, the option A: "Prepared for display FHX50" has to be selected in
feature 050: "Option Measurement Device".
• If a Micropilot has not been ordered in the version "Prepared for display FHX50", but is nevertheless to be equipped with
an FHX50, it is essential to select the option B: "Not prepared for display FHX50" in feature 050: "Option Measurement
Device" of the FHX50. In this case, a retrofit kit, needed to prepare the Micropilot for the remote display, is supplied
together with the FHX50.
For details refer to the document SD01007F.
Horn protection for

80 mm (3 in) horn antenna
ød
ø96 (3.78)
³ DN100 237 (9.33) mm (in)

A0019143
For details please refer to the Mounting Instructions SD01084F.

Danger of explosion
Avoid electrostatic charging of the horn protection.
84 Endress+Hauser
Horn protection for

100 mm (4 in) horn
antenna
ød
³ DN150
ø116 (4.57)
450 (17.72)
mm (in)
A0019144
For details please refer to the Mounting Instructions SD01084F.

Danger of explosion
Avoid electrostatic charging of the horn protection.
Communication-specific Accessory Description

accessories
Commubox FXA195 HART For intrinsically safe HART communication with FieldCare via the USB interface.
For details refer to Technical Information TI00404F
Commubox FXA291 Connects Endress+Hauser field devices with CDI interface (= Endress+Hauser Common
Data Interface) to the USB interface of a computer.
For details refer to Technical Information TI00405C
HART Loop Converter Evaluates the dynamic HART variables and converts them to analog current signals or
HMX50 limit values.
For details refer to Technical Information TI00429F and Operating Instructions
BA00371F
WirelessHART Adapter Connects field devices to a WirelessHART network.

SWA70 The WirelessHART adapter can be mounted directly at a HART device and is easly
integrated into an existing HART network. It ensures safe data transmission and can be
operated in parallel with other wireless networks.
For details refer to Operating Instructions BA00061S
Endress+Hauser 85
Fieldgate FXA320 Gateway for remote monitoring of connected 4-20mA measuring devices via web
browser.
For details refer to Technical Information TI00025S and Operating Instructions
BA00053S
Fieldgate FXA520 Gateway for remote diagnosis and parametrization of connected HART measuring devices
via web browser.
For details refer to Technical Information TI00025S and Operating Instructions
BA00051S
Field Xpert SFX100 Compact, flexible and robust industry handheld terminal for remote parametrization and
measured value inspection via the HART output or via FOUNDATION Fieldbus .
For details refer to Operating Instructions BA00060S
Service-specific accessories Accessory Description
FieldCare Endress+Hauser's FDT-based Plant Asset Management tool.

Helps to configure and maintain all field devices of your plant. By supplying status
information it also supports the diagnosis of the devices.
For details refer to Operating Instructions BA00027S and BA00059S.
System components Accessory Description
Graphic Data Manager The graphic data manager Memograph M provides information on all the relevant process
Memograph M variables. Measured values are recorded correctly, limit values are monitored and
measuring points analyzed. The data are stored in the 256 MB internal memory and also
on an SD card or USB stick.
For details refer to Technical Information TI00133R and Operating Instructions
BA00247R
RN221N Active barrier with power supply for safe separation of 4 to 20 mA current circuits.
Provides bi-directional HART transmission.
BA00202R
RNS221 Transmitter supply for 2-wire sensors or transmitters exclusively for non-Ex areas.
Provides bi-directional communication using the HART communication sockets.
KA00110R
86 Endress+Hauser
Documentation
The following document types are available:
• On the CD supplied with the device
• In the Download Area of the Endress+Hauser Internet site: www.endress.com ® Download
Standard documentation Micropilot FMR51, FMR52
Correlation of documentations to the device:

Device Power supply, Communikation Document type Document code
output
FMR51 A, B, C, K, L HART Operating Instructions BA01049F/00/EN

FMR52
Brief Operating Instructions KA01100F/00/EN
Description of Device Parameters GP01014F/00/EN
G PROFIBUS PA Operating Instructions BA01125F/00/EN

(in preparation)
E FOUNDATION Fieldbus Operating Instructions BA01121F/00/EN

(in preparation)
Supplementary Device Document type Document code

documentation
Fieldgate FXA520 Technical Information TI369F/00/EN
Tank Side Monitor NRF590 Technical Information TI402F/00/EN
Operating Instructions BA256F/00/EN
Description of Device Parameters BA257F/00/EN
Safety Instructions (XA) Depending on the approval, the following Safety Instructions (XA) are supplied with the device. They are an
integral part of the Operating Instructions.
Feature 010 Approval Available for Safety Instructions HART Safety Instructions
PROFIBUS
FOUNDATION Fieldbus
BA ATEX: II 1 G Ex ia IIC T6 Ga • FMR51

XA00677F XA00685F
• FMR52
BB ATEX: II 1/2 G Ex ia IIC T6-T1 Ga/Gb • FMR51

XA00677F XA00685F
• FMR52
BC ATEX: II 1/2 G Ex d [ia] IIC T6-T1 Ga/Gb • FMR51 XA00680F XA00688F

• FMR52
BD ATEX: II 1/2/3 G Ex ic [ia Ga] IIC T6-T1 Ga/Gb/Gc • FMR51 XA00678F XA00686F
• FMR52
BG ATEX: II 3 G Ex nA IIC T6-T1 Gc • FMR51

XA00679F XA00687F
• FMR52
BH ATEX: II 3 G Ex ic IIC T6-T1 Gc • FMR51

XA00679F XA00687F
• FMR52
BL ATEX: II 1/2/3 G Ex nA [ia Ga] IIC T6-T1 Ga/Gb/Gc • FMR51 XA00678F XA00686F
• FMR52
B2 ATEX: II 1/2 G Ex ia IIC T6-T1 Ga/Gb • FMR51 XA00683F XA00691F

ATEX: II 1/2 D Ex ia IIIC Txx°C Da/Db • FMR52
B3 ATEX: II 1/2 G Ex d [ia] IIC T6-T1 Ga/Gb • FMR51 XA00684F XA00692F

ATEX: II 1/2 D Ex ta IIIC Txx°C Da/Db • FMR52
Endress+Hauser 87
Feature 010 Approval Available for Safety Instructions HART Safety Instructions
PROFIBUS
FOUNDATION Fieldbus
B4 ATEX:II 1/2 G Ex ia IIC T6-T1 Ga/Gb • FMR51 XA00681F XA00689F

ATEX: II 1/2 G Ex d [ia] IIC T6-T1 Ga/Gb • FMR52
IA IECEx: Ex ia IIC T6-T1 Ga • FMR51

XA00677F XA00685F
• FMR52
IB IECEx: Ex ia IIC T6-T1 Ga/Gb • FMR51

XA00677F XA00685F
• FMR52
IC IECEx: Ex d [ia] IIC T6-T1 Ga/Gb • FMR51 XA00680F XA00688F

• FMR52
ID IECEx: Ex ic [ia Ga] IIC T6-T1 Ga/Gb/Gc • FMR51 XA00678F XA00686F

• FMR52
IG IECEx: Ex nA IIC T6-T1 Gc • FMR51

XA00679F XA00687F
• FMR52
IH IECEx: Ex ic IIC T6-T1 Gc • FMR51

XA00679F XA00687F
• FMR52
IL IECEx: Ex nA [ia Ga] IIC T6-T1 Ga/Gb/Gc • FMR51 XA00678F XA00686F

• FMR52
I2 IECEx: Ex ia IIC T6-T1 Ga/Gb • FMR51 XA00683F XA00691F

IECEx: Ex ia IIIC Txx°C Da/Db • FMR52
I3 IECEx: Ex d [ia] IIC T6-T1 Ga/Gb • FMR51 XA00684F XA00692F

IEXEx: Ex ta IIIC Txx°C Da/Db • FMR52
I4 IECEx: Ex ia IIC T6-T1 Ga/Gb • FMR51 XA00681F XA00689F

IECEx: Ex d [ia] IIC T6-T1 Ga/Gb • FMR52
For certified devices the relevant Safety Instructions (XA) are indicated on the nameplate.
If the device is prepared for the remote display FHX50 (product structure: feature 030: Display, Operation",
option L or M), the Ex marking of some certificates changes according to the following table 9):
Feature 010 ("Approval") Feature 030 ("Display, Operation") Ex marking
BE L oder M ATEX II 1D Ex ta [ia] IIIC T500 xx°C Da
BF L oder M ATEX II 1/2 D Ex ta [ia Db] IIIC Txx°C Da/Db
BG L oder M ATEX II 3G Ex nA [ia Ga] IIC T6 Gc
BH L oder M ATEX II 3G Ex ic [ia Ga] IIC T6 Gc
B3 L oder M ATEX II 1/2G Ex d [ia] IIC T6 Ga/Gb,

ATEX II 1/2D Ex ta [ia Db] IIIC Txx°C Da/Db
IE L oder M IECEx Ex ta [ia] IIIC T500 xx°C Da
IF L oder M IECEx ta [ia Db] IIIC Txx°C Da/Db
IG L oder M IECEx Ex nA [ia Ga] IIC T6 Gc
IH L oder M IECEx Ex ic [ia Ga] IIC T6 Gc
I3 L oder M IECEx Ex d [ia] IIC T6 Ga/Gb,

IECEx Ex ta [ia Db] IIIC Txx°C Da/Db
Registered trademarks
HARTÒ
Registered trademark of the HART Communication Foundation, Austin, USA
9) The marking of certificates not mentioned in this table are not affected by the FHX50.
88 Endress+Hauser
PROFIBUSÒ
Registered trademark of the PROFIBUS User Organization, Karlsruhe, Germany
FOUNDATIONTM Fieldbus
Registered trademark of the Fieldbus Foundation, Austin, Texas, USA
KALREZÒ, VITONÒ
Registered trademark of DuPont Performance Elastomers L.L.C., Wilmington, USA
TEFLONÒ
Registered trademark of E.I. DuPont de Nemours & Co., Wilmington, USA
TRI CLAMPÒ
Registered trademark of Alfa Laval Inc., Kenosha, USA
Patents
This product may be protected by at least one of the following patents.
Further patents are pending.
US Patents EP Patents
5.948.979 882 957
6.087.978 955 527
6.140.940 -
6.155.112 834 722
- 882 955
6.266.022 1 083 413
6.295.874 210 567
6.512.358 1 301 914
6.606.904 -
6.640.628 -
6.679.115 1 360 523
- 1 389 337
6.779.397 -
7.201.050 -
7.412.337 -
7.552.634 -
7.730.760 -
7.819.002 -
- 1 774 616
7.966.141 -
8.040.274 -
8.049.371 -
Endress+Hauser 89
Instruments International
Endress+Hauser
Instruments International AG
Kaegenstrasse 2
4153 Reinach
Switzerland
Tel.+41 61 715 81 00
Fax+41 61 715 25 00
www.endress.com
info@ii.endress.com
TI01040F/00/EN/01.12
71162672
CCS/EH-COSIMA ProMoDo

Micropilot FMR51 FMR52 TI

Uploaded by

Copyright:

Available Formats

Micropilot FMR51 FMR52 TI

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Micropilot FMR51 FMR52 TI

Uploaded by

Copyright:

Available Formats

Technical Information

Micropilot FMR51, FMR52

Application • Pressure range: –1 to +16 bar (–14.5 to +232 psi)

Important document information . . . . . . . . . . . . . . . . 4 Degree of protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

Important document information

Direct current and alternating current

Protective ground connection

Symbols for certain types of information

1, 2, 3 ... Item numbers

A-A, B-B, C-C, ... Sections

Safe area (non-hazardous area)

Symbols at the device

Temperature resistance of the connection cables

Function and system design

å1 Setup parameters of the Micropilot

Life cycle of the product

Engineering Procurement Installation Commissioning Operation Maintenance Retirement

Measuring range Maximum measuring range

Device Maximum measuring range

FMR51 - standard version 40 m (131 ft)

FMR51 - with "Advanced dynamics" application package 70 m (230 ft)

FMR52 - standard version 40 m (131 ft)

FMR52 - with "Advanced dynamics" application package 60 m (197 ft)

Usable measuring range

A 1.4 to 1.9 non-conducting liquids, e.g. liquefied gas 1)

B 1.9 to 4 non-conducting liquids, e.g. benzene, oil, toluene, …

C 4 to 10 e.g. concentrated acids, organic solvents, esters, aniline, alcohol, acetone, …

1) Treat Ammonia NH3 as a medium of group A.

Device Storage tank

FMR51 40 mm (1½ in) 50 mm (2 in) 80 mm (3 in) 100 mm (4 in)

FMR52 - 50 mm (2 in) 80 mm (3 in) -

Measuring range [m (ft)]

Device Buffer tank

Moving surfaces (e.g. continuous filling, from above, mixing jets)

FMR51 40 mm (1½ in) 50 mm (2 in) 80 mm (3 in) 100 mm (4 in)

FMR52 - 50 mm (2 in) 80 mm (3 in) -

7.5 7.5 7.5

Measuring range [m (ft)]

Device Process tank with agitator

Turbulent surface. Single stage agitator (frot < 1 Hz)

FMR51 40 mm (1½ in) 50 mm (2 in) 80 mm (3 in) 100 mm (4 in)

FMR52 - 50 mm (2 in) 80 mm (3 in) -

Measuring range [m (ft)]

Device Stilling well Bypass

Antenna size Antenna size

FMR51 40 to 100 mm ( 1½ ... 4 in) 40 to 100 mm ( 1½ ... 4 in)

FMR52 50 to 80 mm ( 2 ... 3 in) 50 to 80 mm ( 2 ... 3 in)

Measuring range [m (ft)]

Operating frequency K-band (~ 26 GHz)

Transmitting power Distance Average energy density in beam direction

Standard version With "Advanced dynamics" application

1 m (3.3 ft) < 12 nW/cm2 < 64 nW/cm2

5 m (16 ft) < 0.4 nW/cm2 < 2.5 nW/cm2

Signal coding FSK ±0.5 mA over current signal

Data transmission rate 1 200 Bit/s

Galvanic isolation Yes

PROFIBUS PA (in preparation)

Signal coding Manchester Bus Powered (MBP)

Data transmission rate 31.25 kBit/s, voltage mode

Galvanic isolation Yes